page 10/20 SERIES

3 Single Wheel Furniture Casters CASTER “101”

Caster Size: A loose term for classifying
page 12 SERIES casters, based on the nominal diameter
3 Nylon Twin Wheel Casters of the wheel. A “6 inch” caster is any
caster having a 6 inch diameter wheel.

page 21 SERIES Face (Tread Width): The width of the

4 Institutional Casters wheel tread cross-section, measured at
the base of the tread rather than at the
point of floor contact.
page 30 SERIES
4 General Duty Dolly Casters Offset: The per-
pendicular dis-
tance between
page 31/32/33 SERIES the vertical cen-
5 Light Duty Casters terlines of the
kingpin and the
axle of a swivel
page 40/44 SERIES caster. Larger
6 Medium Duty Casters offsets mean
easier swiveling,
shorter offsets
page 50 SERIES yield greater
7 Medium Heavy Duty Casters strength.

Overall Height:
page 52/54 SERIES The vertical dis-
8 Heavy Duty Casters tance from the
top of the caster
mounting plate
page 60 SERIES to the bottom of
9 Heavy Duty Casters the wheel.

Swivel Radius: The horizontal distance from the vertical cen-

page 65 SERIES terline of the kingpin to the outside edge of the wheel tread.
9 Extra Heavy Duty Casters This dimension indicates the minimum distance required for
the caster to swivel 360o when mounted.

page 71/72 SERIES Rollability: Rollability is affected by wheel size, tread type, and
10 Medium Duty Kingpinless Casters bearing type. The larger the wheel, the easier it will roll. A hard
narrow crowned tread rolls easier than a soft flat tread on a
smooth floor. However, soft treads protect floors and pass over
page 75 SERIES floor obstructions more easily.
11 Heavy Duty Kingpinless Casters
Swivel Types:

page 76 SERIES Single Ball: Most economical and basic of swivel variations.
11 Extreme Duty Kingpinless Casters Found on most dolly casters. Not recommended for shock
conditions.

page LEVEL MOUNTS Double Ball: Two sets of ball bearings revolve in upper and
12-13 Tube Ends, Level Mounts, Glides lower raceways. The upper raceway supports direct loads; the
lower absorbs shock to the kingpin from side forces.

page FLOOR LOCKS KingpinlessTM: This design eliminates

14 Various Sizes and Types the cause of most caster failure, the king-
pin. Proven design absorbs outside
forces by utilizing a precision machined
page MATERIAL HANDLING raceway and hardened ball bearings.
14 Hand Trucks, Pallet Jacks, Dollies
 Resistance

Range (F)
Protection

Resitance

Operation

Operating
Rollability

Chemical
Capacity

Bearing
Options
IDEAL ACCEPTABLE NOT RECOMMENDED

Impact

Quiet
Floor

Load
Description

TRThermoplastic
Non-marking gray rubber wheel provides a -40 Precision
soft and cushioned ride. Thermoplastic rub- to Ball
ber resists chemicals, caustics, oils, acids 180
Rubber and wear. TR wheels offer excellent floor
Straight
Roller
protection.
Delrin

RIRubber on Iron
Cushioned rubber tread for quiet movement -40 Straight
with medium to heavy loads. These univer- to Roller
sal rubber wheels are very resilient and pro- 140
vide good floor protection. Delrin
Tapered

PP
Polyurethane tread for high load capacity -40 Precision
and extended wear. Protects floors and to Ball
Polyurethane on resists chemicals, caustics, acids, and oils. 180
Polypropylene Tread and hub are mechanically interlocked
Straight
Roller
to eliminate tread separation.
Delrin

-50

SUSolid Urethane
Solid urethane/elastomer wheels are mold- Precison
ed from high strength compounds that pos- to
Ball
SU 180
sess the load characteristics of steel, but Caged

SESolid Elastomer give the smooth ride expected from -50

Roller
polyurethane. Solid wheel has no core, to
SE 180 Delrin

STANDARD WHEELS
thereby eliminating tread separation.

PAPolyurethane on Aluminum
Polyurethane tread chemically bonded to a -40 Straight
metal core delivers a cushioned ride, excel- to Roller
lent mobility, and extended life under 180
Delrin
PIPolyurethane on Iron extremely heavy loads. They provide floor
protection and wear much longer than most Tapered
other wheel materials.

-20

GPReinforced Polypropylene
Glass-reinforced polypropylene wheels offer Precison
a price-competitive alternative to phenolic to Ball
wheels. These wheels are ideal where high GP 250 Straight

GHHi-Temp Polypropylene impacts or moisture are a factor. GH wheels -20 Roller

to Delrin
are ideally suited for high-temperature appli- GH
480 Plain Bore
cations.

PNPhenolic
Phenolic wheels offer a high strength, less -40 Straight
expensive alternative for demanding applica- to Roller
tions. Phenolic wheels are non-marking, 275 Delrin
non-conductive, and provide good floor pro- Tapered
tection. Plain Bore

POPolypropylene
Polypropylene wheel material is light weight, -20 Straight
less expensive, and high in impact strength. to Roller
It resists water and chemical absorption, 180
Delrin
even stands up to steam cleaning. Non-
marking. Plain Bore

CICast Iron
Cast iron wheels are exceptionally long-last- -40 Straight
ing, highly shock-resistant, and a good to Roller
choice for warehouses and manufacturing 800
Tapered
plants. Not recommended for applications
where noise or floor protection are a con- Plain Bore
cern.

FSForged Steel
Drop forged steel wheels are die formed -50 Straight
from pre-heated carbon steel billets. Forged to Roller
steel wheels offer the greatest load capacity, 800
Tapered
impact strength, and rollability of all caster
wheels.

VIV-Groove Steel
High-strength iron castings or forged steel -50 Straight
with a 90o groove (VI) or flange (FL) for to Roller
operation on in-plant track. These wheels 800
Tapered

FLFlanged Steel are used to control the flow of a load in pro-

duction line applications.

SFFull Pnuematic
This tube-type (SF) or solid cushion (SN), Flanged
tire combines shock absorbtion with quiet Ball
operation and easy rolling.
Straight

SNSemi-Pneumatic
 10/20 SERIES
FURNITURE CASTERS
Dia. Width Wheel Mounting Mount Finish Capacity Overall Model
(IN) (IN) Type Type Size ( LBS) HT.(IN) No.
2 7/8 Hard Rubber Grip Ring 7/16x7/8 Zinc 75 2.5 10ZH20-G714
2 7/8 Soft Rubber Grip Ring 7/16x7/8 Zinc 75 2.5 10ZS20-G714
2 7/8 Hard Rubber Grip Ring 7/16x1-3/8 Zinc 75 2.5 10ZH20-G722
2 7/8 Soft Rubber Grip Ring 7/16x1-3/8 Zinc 75 2.5 10ZS20-G722
2 7/8 Hard Rubber Grip Ring 3/8x1 Zinc 75 2.5 10ZH20-G616
2 7/8 Soft Rubber Grip Ring 3/8x1 Zinc 75 2.5 10ZS20-G616
2 7/8 Hard Rubber Threaded 5/16-18x3/4 Zinc 75 2.5 10ZH20-T512
2 7/8 Soft Rubber Threaded 5/16-18x3/4 Zinc 75 2.5 10ZS20-T512
2 7/8 Hard Rubber Threaded 3/8-16x1-1/2 Zinc 75 2.5 10ZH20-T624
2 7/8 Soft Rubber Threaded 3/8-16x1-1/2 Zinc 75 2.5 10ZS20-T624
2 7/8 Hard Rubber Wood Stem 5/16 x 1-1/2 Zinc 75 2.5 10ZH20-W524
7/8
Features: 2
2 7/8
Soft Rubber
Hard Rubber
Wood Stem
Top Plate
5/16 x 1-1/2
1-3/16 x 2
Zinc
Zinc
75
75
2.5
2.625
10ZS20-W524
10ZH20-P1932
Description: Single wheel furniture 2 7/8 Soft Rubber Top Plate 1-3/16 x 2 Zinc 75 2.625 10ZS20-P1932
casters available with hard or soft 2.5 7/8 Hard Rubber Grip Ring 7/16x7/8 Nickel 75 3.023 10NH25-G714
tread wheels for multiple floor sur- 2.5 7/8 Soft Rubber Grip Ring 7/16x7/8 Nickel 75 3.023 10NS25-G714
2.5 7/8 Hard Rubber Grip Ring 7/16x1-3/8 Nickel 75 3.023 10NH25-G722
faces.
2.5 7/8 Soft Rubber Grip Ring 7/16x1-3/8 Nickel 75 3.023 10NS25-G722
2.5 7/8 Hard Rubber Grip Ring 3/8x1 Nickel 75 3.023 10NH25-G616
Swivel: Double ball bearing design. 2.5 7/8 Soft Rubber Grip Ring 3/8x1 Nickel 75 3.023 10NS25-G616
2.5 7/8 Hard Rubber Threaded 3/8-16x1-1/2 Nickel 75 3.023 10NH25-T624
Finish: Standard zinc or nickel are 2.5 7/8 Soft Rubber Threaded 3/8-16x1-1/2 Nickel 75 3.023 10NS25-T624
2.5 7/8 Hard Rubber Wood Stem 5/16 x 1-1/2 Nickel 75 3.023 10NH25-W524
available as listed; please see 2.5 7/8 Soft Rubber Wood Stem 5/16 x 1-1/2 Nickel 75 3.023 10NS25-W524
options. 3 13/16 Gray Rubber on Polypropylene Grip Ring 7/16x1-3/8 Zinc 90 3.5 20TRP30S-G722
3 13/16 Gray Rubber on Polypropylene Threaded 3/8-16X1-1/2 Zinc 90 3.5 20TRP30S-T624
Options: 3 13/16 Gray Rubber on Polypropylene Threaded 7/16-14X2-1/8 Zinc 90 3.5 20TRP30S-T734
4 15/16 Gray Rubber on Polypropylene Grip Ring 7/16X1-17/32 Zinc 115 4-5/8 20TRP40S-G724
CB: Cam Brake (10 Series) 15/16
4 Gray Rubber on Polypropylene Threaded 1/2-13X1-1/2 Zinc 115 4-11-16 20TRP40S-T824
TB: Tread Brake (20 Series) 4 15/16 Gray Rubber on Polypropylene Threaded 7/16-14X2-1/8 Zinc 115 4-11/16 20TRP40S-T734
AC: Antique Copper Finish (10 Series) 5 15/16 Gray Rubber on Polypropylene Grip Ring 7/16x1-17/32 Zinc 125 5-5/8 20TRP50S-G724
BO: Black Oxide Finish (10 Series) 5 15/16 Gray Rubber on Polypropylene Threaded 1/2-13X1-1/2 Zinc 125 5-23/32 20TRP50S-T824
5 15/16 Gray Rubber on Polypropylene Threaded 7/16-14X2-1/8 Zinc 125 5-23/32 20TRP50S-T734
Mountings, Wheels and Styles: Many
other options available; please call.

12 SERIES
NYLON TWIN WHEEL CASTERS

Features: Dia.
(IN)
Wheel &
Tread Type
Brake
Option
Finish Capacity Overall
(LBS) HT.(IN)
Model
No.
Description: Available in a variety of stem 2 Nylon-Hard No Brake Black 90 2.5 12BH50
and body combinations for any applica- 2 Nylon-Hard With Brake Black 90 2.5 12BH50-B
tion. These hooded twin wheel casters are 2 Urethane-Soft No Brake Black 90 2.5 12BS50
2 Nylon-Hard No Brake Chrome 90 2.5 12CH50
made of extra durable nylon. For your
2 Nylon-Hard No Brake Brass 90 2.5 12RH50
application, please choose the body size 2 Nylon-Hard No Brake Antique 90 2.5 12AH50
and finish, then select a stem. Please see 2.5 Nylon-Hard No Brake Black 100 2.75 1 2 B H 6 0
ordering example below. 2.5 Nylon-Hard With Brake Black 100 2.75 12BH60-B
2.5 Nylon-Hard No Brake Chrome 100 2.75 1 2 C H 6 0
Options: 2.5 Nylon-Hard No Brake Brass 100 2.75 1 2 R H 6 0
Mountings, Wheels and Styles: Many other 2.5 Nylon-Hard No Brake Antique 100 2.75 1 2 A H 6 0
options available; please call.
Stem Options:
Also Available: Also Available: Ordering Information: Description Model
Stem No.
14 Series 16 Series Grip Ring Stem 3/8 x 1 G616
1. Select body according to Grip Ring Stem 7/16 x 7/8 G714
Die Cast Metal Bodies Metal Ball Casters your needs (see chart, above). Grip Ring Stem 7/16 x 1 G716
2. Select stem for the body. Grip Ring Stem 7/16 x 1-3/8 G722
Threaded Stem 5/16-18 x 3/4 T512
3. Use the model number for the
Threaded Stem 5/16-18 x 1 T516
body and combine it with the Threaded Stem 3/8-16 x 3/4 T612
model number for the stem. Plate 1-1/2 x 1-1/2* P2424
EXAMPLE: Plate 1-3/16 x 2* P1932
Wood Stem 5/16x1-15/32 W523
12BH50-G716
* Special overall height

3
 21 SERIES
INSTITUTIONAL CASTERS
Swivel Section: Double ball bearing design.
Finish: Corrosion resistant zinc.
Wheel Bearings: Precision ball, delrin, and plain self-lubricating bearings.
Options: TB: Tread Brake
Dia. Width Wheel Bearing Stem Stem Capacity Overall Model
(IN) (IN) Type Type Type Size (LBS) HT.(IN) No.
3 1-1/4 Polypropylene Plain Threaded 1/2-13X1-1/2 270 3-47/64 21POP30S-T824
3 1-1/4 Gray Rubber on Polypropylene Delrin Threaded 1/2-13X1-1/2 180 3-47/64 21TRD30S-T824
3 1-1/4 Gray Rubber on Polypropylene Prec. Ball Threaded 1/2-13X1-1/2 180 3-47/64 21TRB30S-T824
3 1-1/4 Polyurethane on Polypropylene Delrin Threaded 1/2-13X1-1/2 225 3-47/64 21PPD30S-T824
3 1-1/4 Polyurethane on Polypropylene Prec. ball Threaded 1/2-13X1-1/2 225 3-47/64 21PPB30S-T824
MOUNTING 4 1-1/4 Polypropylene Plain Threaded 1/2-13X1-1/2 275 4-7/8 21POP40S-T824
4 1-1/4 Gray Rubber on Polypropylene Delrin Threaded 1/2-13X1-1/2 225 4-7/8 21TRD40S-T824
SOCKETS 4 1-1/4 Gray Rubber on Polypropylene Prec. ball Threaded 1/2-13X1-1/2 225 4-7/8 21TRB40S-T824
4 1-1/4 Polyurethane on Polypropylene Delrin Threaded 1/2-13X1-1/2 275 4-7/8 21PPD40S-T824
4 1-1/4 Polyurethane on Polypropylene Prec. ball Threaded 1/2-13X1-1/2 275 4-7/8 21PPB40S-T824
4 1-1/4 Polypropylene Plain Threaded 7/16-14X2-1/8 225 5 21POP40S-T734
4 1-1/4 Gray Rubber on Polypropylene Delrin Threaded 7/16-14X2-1/8 190 5 21TRD40S-T734
4 1-1/4 Gray Rubber on Polypropylene Prec. ball Threaded 7/16-14X2-1/8 190 5 21TRB40S-T734
4 1-1/4 Polyurethane on Polypropylene Delrin Threaded 7/16-14X2-1/8 225 5 21PPD40S-T734
4 1-1/4 Polyurethane on Polypropylene Prec. ball Threaded 7/16-14X2-1/8 225 5 21PPB40S-T734
4 1-1/4 Polypropylene Plain Grip Ring 7/16x1-3/8 225 5 21POP40S-G722
4 1-1/4 Gray Rubber on Polypropylene Delrin Grip Ring 7/16x1-3/8 190 5 21TRD40S-G722
USE WITH 7/16” GRIP RINGS 4 1-1/4 Gray Rubber on Polypropylene Prec. ball Grip Ring 7/16x1-3/8 190 5 21TRB40S-G722
Model Tube 4 1-1/4 Polyurethane on Polypropylene Delrin Grip Ring 7/16x1-3/8 225 5 21PPD40S-G722
No. I.D. 4 1-1/4 Polyurethane on Polypropylene Prec. ball Grip Ring 7/16x1-3/8 225 5 21PPB40S-G722
82SRH777G .777 5 1-1/4 Polypropylene Plain Threaded 1/2-13X1-1/2 275 6 21POP50S-T824
ROUND TUBE

82SRH872G .872 5 1-1/4 Gray Rubber on Polypropylene Delrin Threaded 1/2-13X1-1/2 250 6 21TRD50S-T824
82SRH902G .902 5 1-1/4 Gray Rubber on Polypropylene Prec. ball Threaded 1/2-13X1-1/2 250 6 21TRB50S-T824
82SRH1072G 1.072 5 1-1/4 Polyurethane on Polypropylene Delrin Threaded 1/2-13X1-1/2 300 6 21PPD50S-T824
82SRH112G 1.12 5 1-1/4 Polyurethane on Polypropylene Prec. ball Threaded 1/2-13X1-1/2 300 6 21PPB50S-T824
82SRH131G 1.31 5 1-1/4 Polypropylene Plain Threaded 7/16-14X2-1/8 225 6 21POP50S-T734
82SRH1495G 1.495 5 1-1/4 Gray Rubber on Polypropylene Delrin Threaded 7/16-14X2-1/8 190 6 21TRD50S-T734
82SSH620G .620 5 1-1/4 Gray Rubber on Polypropylene Prec. ball Threaded 7/16-14X2-1/8 190 6 21TRB50S-T734
82SSH652G .652
SQUARE TUBE

5 1-1/4 Polyurethane on Polypropylene Delrin Threaded 7/16-14X2-1/8 225 6 21PPD50S-T734

82SSH880G .880 5 1-1/4 Polyurethane on Polypropylene Prec. ball Threaded 7/16-14X2-1/8 225 6 21PPB50S-T734
82SSH902G .902 5 1-1/4 Polypropylene Plain Grip Ring 7/16X1-3/8 225 6 21POP50S-G722
82SSH101G 1.01 5 1-1/4 Gray Rubber on Polypropylene Delrin Grip Ring 7/16X1-3/8 190 6 21TRD50S-G722
82SSH112G 1.12 5 1-1/4 Gray Rubber on Polypropylene Prec. ball Grip Ring 7/16X1-3/8 190 6 21TRB50S-G722
82SSH1152G 1.152 5 1-1/4 Polyurethane on Polypropylene Delrin Grip Ring 7/16X1-3/8 225 6 21PPD50S-G722
82SSH1402G 1.402 5 1-1/4 Polyurethane on Polypropylene Prec. ball Grip Ring 7/16X1-3/8 225 6 21PPB50S-G722

30 SERIES
DOLLY CASTERS
Swivel Section: Single ball raceway design utilizing a one-piece heavy gauge steel formed construction.
Finish: Corrosion resistant zinc.
Wheel Bearings: Standard plain self-lubricating bearings.
Top Plate: Please see chart below.
Options: CB: Cam Brake (Swivel Only)

Dia. Width Wheel Bearing Capacity Overall Swivel Rigid

RIGID TOP PLATES (IN) (IN) Type Type (LBS) HT.(IN) Model No. Model No.
Caster Mounting Bolt Hole Bolt 2 1 Sintered Iron Plain 150 2-1/2 30CIP20S 30CIP20R
Size Plate Spacing Size 2 1 Soft Rubber Plain 90 2-1/2 30SRP20S 30SRP20R
2” 1-1/2 x 2-21/32 15/16 x 2-1/8 1/4 2 1 Hard Rubber Plain 150 2-1/2 30HRP20S 30HRP20R
2-1/2” 2-1/4 x 4-7/16 1-1/16 x 3-1/2 5/16 2 1 Polypropylene Plain 150 2-1/2 30POP20S 30POP20R
3” 2-1/2 x 4-15/16 1-3/16 x 4 5/16 2-1/2 1 Sintered Iron Plain 200 3-3/16 30CIP25S 30CIP25R
4” 3-1/8 x 6-1/4 1-3/4 x 5 3/8 2-1/2 1-1/8 Soft Rubber Plain 100 3-3/16 30SRP25S 30SRP25R
2-1/2 1-1/8 Hard Rubber Plain 200 3-3/16 30HRP25S 30HRP25R
2-1/2 1-1/8 Polypropylene Plain 200 3-3/16 30POP25S 30POP25R
SWIVEL TOP PLATES 3 1-3/16 Sintered Iron Plain 300 3-13/16 30CIP30S 30CIP30R
3 1-1/4 Soft Rubber Plain 175 3-13/16 30SRP30S 30SRP30R
Caster Mounting Bolt Hole Bolt 3 1-1/4 Hard Rubber Plain 270 3-13/16 30HRP30S 30HRP30R
Size Plate Spacing Size 3 1-1/4 Polypropylene Plain 270 3-13/16 30POP30S 30POP30R
2” 1-7/8 x 2-9/16 15/16 x 2-1/8 1/4 4 1-3/8 Sintered Iron Plain 450 5 30CIP40S 30CIP40R
2-1/2” 2-3/4 x 3-13/16 1-3/4 x 3 5/16 4 1-5/16 Soft Rubber Plain 225 5 30SRP40S 30SRP40R
3” 3-1/8 x 4-1/8 2-3/8 x 3-3/8* 5/16 4 1-5/16 Hard Rubber Plain 350 5 30HRP40S 30HRP40R
4” 4 x 5-1/8 3x4 3/8 4 1-5/16 Polypropylene Plain 350 5 30POP40S 30POP40R
* Slotted to 3-7/16
4
 31/32/33 S E R I E S
LIGHT DUTY CASTERS

Features: #31 TOP PLATE

Swivel Section: Dual ball raceway design uti- Mounting Bolt Hole Bolt
lizing a heavy-gauge steel top plate attached Plate Spacing Size
to a full-drawn steel horn with integral, hard- 3-3/4 x 4-5/8 2-5/8 x 3-5/8 3/8
ened raceways. slotted to
Finish: Corrosion resistant zinc. 3x3
Wheel Bearings: Plain self-lubricating, del-
rin,roller, and precision ball bearings are
available as listed.
#32 TOP PLATE
Mounting Bolt Hole Bolt
Options: Plate Spacing Size
TB: Tread Brake 3-1/2” to 5" (Swivel Only) Swivel = 2-7/8 x 3-5/8 1-3/4 x 2-15/16 5/16
FB: Face Brake 3-1/2" to 5" (Swivel Only) Rigid = 2-15/16 x 4-1/8 1-3/4 x 2-15/16 5/16
CB: Cam Brake 3" (32 Series Swivel Only)
NEW! SS: Stainless Steel (32 Series Only)
TLB: Total Lock Brake 3” to 5"
#33 TOP PLATE
Optional Overall Heights: 32 Series Only Mounting Bolt Hole Bolt
32 Series Standard Optional Plate Spacing Size
Overall Overall 3-1/8 x 4-1/8 2-3/8 x 3-13/32 5/16
HT. HT.
3” Model 3-13/16” 4-1/4”
3-1/2” Model 4-3/4” 4-11/16”
4” Model 5” 5-1/8” Swivel Rigid Swivel Rigid Swivel Rigid
Model No. Model No. Model No. Model No. Model No. Model No.

Dia. Width Wheel Bearing Capacity Overall #31 #31 #32 #32 #33 #33
(IN) (IN) Type Type (LBS) HT.(IN) Top Top Top Top Top Top
Plate Plate Plate Plate Plate Plate
3 1-1/4 Phenolic Roller 270 3-13/16 32PNR30S 32PNR30R
3 1-1/4 Phenolic Plain 270 3-13/16 32PNP30S 32PNP30R
3 1-1/4 Polypropylene Plain 270 3-13/16 32POP30S 32POP30R
3 1-1/4 Polyurethane on Polypropylene Delrin 225 3-13/16 32PPD30S 32PPD30R
3 1-1/4 Polyurethane on Polypropylene Prec. Ball 225 3-13/16 32PPB30S 32PPB30R
3 1-1/4 Gray Rubber on Polypropylene Delrin 180 3-13/16 32TRD30S 32TRD30R
3 1-1/4 Gray Rubber on Polypropylene Prec. Ball 180 3-13/16 32TRB30S 32TRB30R

3-1/2 1-1/4 Polypropylene Plain 275 4-3/4 31POP35S 31POP35R 32POP35S 32POP35R 33POP35S 33POP35R
3-1/2 1-1/4 Polyurethane on Polypropylene Delrin 250 4-3/4 31PPD35S 31PPD35R 32PPD35S 32PPD35R 33PPD35S 33PPD35R
3-1/2 1-1/4 Polyurethane on Polypropylene Prec. Ball 250 4-3/4 31PPB35S 31PPB35R 32PPB35S 32PPB35R 33PPB35S 33PPB35R
3-1/2 1-1/4 Gray Rubber on Polypropylene Delrin 225 4-3/4 31TRD35S 31TRD35R 32TRD35S 32TRD35R 33TRD35S 33TRD35R
3-1/2 1-1/4 Gray Rubber on Polypropylene Prec. Ball 225 4-3/4 31TRB35S 31TRB35R 32TRB35S 32TRB35R 33TRB35S 33TRB35R

4 1-1/4 Phenolic Roller 270 5 32PNR40S 32PNR40R

4 1-1/4 Phenolic Plain 270 5 32PNP40S 32PNP40R
4 1-1/4 Polypropylene Plain 275 5 31POP40S 31POP40R 32POP40S 32POP40R 33POP40S 33POP40R
4 1-1/4 Polyurethane on Polypropylene Delrin 300 5 31PPD40S 31PPD40R 32PPD40S 32PPD40R 33PPD40S 33PPD40R
4 1-1/4 Polyurethane on Polypropylene Prec. Ball 300 5 31PPB40S 31PPB40R 32PPB40S 32PPB40R 33PPB40S 33PPB40R
4 1-1/4 Gray Rubber on Polypropylene Delrin 250 5 31TRD40S 31TRD40R 32TRD40S 32TRD40R 33TRD40S 33TRD40R
4 1-1/4 Gray Rubber on Polypropylene Prec. Ball 250 5 31TRB40S 31TRB40R 32TRB40S 32TRB40R 33TRB40S 33TRB40R
4 1-1/2 Phenolic High Temp Plain 300 5 31HTP40S 31HTP40R 32HTP40S 32HTP40R 33HTP40S 33HTP40R
4 1-1/2 Polypropylene GP High Temp Plain 300 5 31GHP41S 31GHP41R 32GHP41S 32GHP41R 33GHP41S 33GHP41R

5 1-1/4 Phenolic Roller 300 6-1/8 32PNR50S 32PNR50R

5 1-1/4 Phenolic Plain 300 6-1/8 32PNP50S 32PNP50R
5 1-1/4 Polypropylene Plain 290 6-1/8 31POP50S 31POP50R 32POP50S 32POP50R 33POP50S 33POP50R
5 1-1/4 Polyurethane on Polypropylene Delrin 300 6-1/8 31PPD50S 31PPD50R 32PPD50S 32PPD50R 33PPD50S 33PPD50R
5 1-1/4 Polyurethane on Polypropylene Prec. Ball 300 6-1/8 31PPB50S 31PPB50R 32PPB50S 32PPB50R 33PPB50S 33PPB50R
5 1-1/4 Gray Rubber on Polypropylene Delrin 250 6-1/8 31TRD50S 31TRD50R 32TRD50S 32TRD50R 33TRD50S 33TRD50R
5 1-1/4 Gray Rubber on Polypropylene Prec. Ball 250 6-1/8 31TRB50S 31TRB50R 32TRB50S 32TRB50R 33TRB50S 33TRB50R

6 1-3/8 Polypropylene Plain 300 7-1/16 32POP60S 32POP60R

6 1-3/8 Polyurethane on Polypropylene Delrin 300 7-1/16 32PPD60S 32PPD60R
6 1-3/8 Polyurethane on Polypropylene Ball 300 7-1/16 32PPF60S 32PPF60R
6 1-3/8 Gray Rubber on Polypropylene Delrin 250 7-1/16 32TRD60S 32TRD60R
6 1-3/8 Gray Rubber on Polypropylene Ball 250 7-1/16 32TRF60S 32TRF60R

5
 40/44 SERIES
MEDIUM DUTY CASTERS

Dia. Width Wheel Bearing Capacity Overall Swivel Rigid

(IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
3-1/4 1-1/2 Cast Iron Roller 400 4-1/4 40CIR31S 40CIR31R
3-1/4 1-1/2 Phenolic Roller 600 4-1/4 40PNR31S 40PNR31R
3-1/4 1-1/2 Polyurethane on Aluminum Roller 420 4-1/4 4 0 PA R 3 1 S 4 0 PA R 3 1 R
3-1/4 2 Cast Iron Roller 700 4-1/4 44CIR32S 44CIR32R
3-1/4 2 Phenolic Roller 700 4-1/4 44PNR32S 44PNR32R
3-1/4 2 Polyurethane on Iron Roller 540 4-1/4 44PIR32S 44PIR32R
4 1-1/2 Cast Iron Roller 500 5-5/8 40CIR41S 40CIR41R
4 1-1/2 Phenolic Roller 600 5-5/8 40PNR41S 40PNR41R
4 1-1/2 Polypropylene Roller 375 5-5/8 40POR41S 40POR41R
Features: 4 1-1/2 Polyurethane on Aluminum Roller 600 5-5/8 4 0 PA R 4 1 S 4 0 PA R 4 1 R
Swivel Section: 4 1-1/2 Polyurethane on Iron Roller 600 5-5/8 40PIR41S 40PIR41R
4 1-1/2 Rubber on Iron Roller 250 5-5/8 40RIR41S 40RIR41R
Cold-forged top plate, yoke and button 4 1-1/2 V-Groove Iron Roller 700 5-5/8 40VIR41S 40VIR41R
are all heat treated to prevent brinelling, 4 1-1/2 Forged Steel Roller 900 5-5/8 44FSR41S 44FSR41R
improve swivel action and increase serv- 4 2 Cast Iron Roller 700 5-5/8 44CIR42S 44CIR42R
ice life. 4 2 Phenolic Roller 700 5-5/8 44PNR42S 44PNR42R
Kingpin: 4 2 Polypropylene Roller 400 5-5/8 44POR42S 44POR42R
4 2 Polypropylene GP Roller 800 5-5/8 44GPR42S 44GPR42R
5/8” Diameter. 4 2 Polyurethane on Polypropylene Roller 600 5-5/8 44PPR42S 44PPR42R
Axle: 4 2 Polyurethane on Aluminum Roller 700 5-5/8 4 4 PA R 4 2 S 4 4 PA R 4 2 R
1/2” Diameter with lubrication fitting. 4 2 Polyurethane on Iron Roller 700 5-5/8 44PIR42S 44PIR42R
Finish: 4 2 Rubber on Iron Roller 300 5-5/8 44RIR42S 44RIR42R
Corrosion resistant zinc. 4 2 Gray Rubber on Polypropylene Roller 300 5-5/8 44TRR42S 44TRR42R
4 2 Solid Urethane Caged 700 5-5/8 44SUC42S 44SUC42R
Wheel Bearings: 4 2 Solid Elastomer Prec. Ball 900 5-5/8 44SEB42S 44SEB42R
Straight roller bearings standard. 4 2 V-Groove Iron Roller 800 5-5/8 44VIR42S 44VIR42R
5 1-1/2 Cast Iron Roller 600 6-1/2* 40CIR51S 40CIR51R
Options: 5 1-1/2 Phenolic Roller 600 6-1/2* 40PNR51S 40PNR51R
Series Availablity 5 1-1/2 Polypropylene Roller 440 6-1/2* 40POR51S 40POR51R
SL: Swivel Lock 40 & 44 Series 5 1-1/2 Polyurethane on Aluminum Roller 720 6-1/2* 4 0 PA R 5 1 S 4 0 PA R 5 1 R
CB: Cam Brake 40 & 44 Series 5 1-1/2 Polyurethane on Iron Roller 720 6-1/2* 40PIR51S 40PIR51R
5 1-1/2 Rubber on Iron Roller 300 6-1/2* 40RIR51S 40RIR51R
TB: Tread Brake 44 Series Only 5 2 Forged Steel Roller 900 6-1/2* 44FSR52S 44FSR52R
FB: Face Brake 44 Series Only 5 2 Cast Iron Roller 900 6-1/2* 44CIR52S 44CIR52R
TLB: Total Lock Brake 44 Series Only 5 2 Phenolic Roller 900 6-1/2* 44PNR52S 44PNR52R
GS: Grease Seals 40 & 44 Series 5 2 Polypropylene Roller 550 6-1/2* 44POR52S 44POR52R
SS: Stainless Steel 44 Series Only 5 2 Polypropylene GP Roller 900 6-1/2* 44GPR52S 44GPR52R
Delrin Bearings 40 & 44 Series 5 2 Polyurethane on Polypropylene Roller 750 6-1/2* 44PPR52S 44PPR52R
Caged Bearings 44 Series Only 5 2 Polyurethane on Aluminum Roller 900 6-1/2* 4 4 PA R 5 2 S 4 4 PA R 5 2 R
5 2 Polyurethane on Iron Roller 900 6-1/2* 44PIR52S 44PIR52R
5 2 Rubber on Iron Roller 350 6-1/2* 44RIR52S 44RIR52R

*
5 2 Gray Rubber on Polypropylene Roller 450 6-1/2* 44TRR52S 44TRR52R
Optional Optional Standard 5 2 Solid Urethane Caged 900 6-1/2* 44SUC52S 44SUC52R
Overall Height Height 5 2 Solid Urethane H.D. Prec. Ball 900 6-1/2* 44SUB52S 44SUB52R
Height (IN) (IN) 5 2 Solid Elastomer Prec. Ball 900 6-1/2* 44SEB52S 44SEB52R
5 x 2 Models 6-1/8” 6-1/2” 5 2 V-Groove Iron Roller 800 6-1/2* 44VIR52S 44VIR52R
6 x 2 Models 7-1/2” 7-1/4” 6 1-1/2 Cast Iron Roller 600 7-1/4 40CIR61S 40CIR61R
6 1-1/2 Phenolic Roller 800 7-1/4 40PNR61S 40PNR61R
PNEUMATIC MODELS 6 1-1/2 Polyurethane on Iron Roller 800 7-1/4 40PIR61S 40PIR61R
6 1-1/2 Rubber on Iron Roller 370 7-1/4 40RIR61S 40RIR61R
Dia. Width Bearing Overall Swivel Rigid 6 2 Forged Steel Roller 900 7-1/4* 44FSR62S 44FSR62R
(IN) (IN) Type HT. (IN) Model No. Model No. 6 2 Cast Iron Roller 900 7-1/4* 44CIR62S 44CIR62R
6 2 Phenolic Roller 900 7-1/4* 44PNR62S 44PNR62R
8 2-1/2 Ball 10 44SFF825S 44SFF825R 6 2 Polypropylene Roller 650 7-1/4* 44POR62S 44POR62R
10 3-1/2 Ball 12 44SFF1035S 44SFF1035R 6 2 Polypropylene GP Roller 900 7-1/4* 44GPR62S 44GPR62R
12 3-1/2 Ball 15 44SFF1235S 44SFF1235R 6 2 Polyurethane on Polypropylene Roller 900 7-1/4* 44PPR62S 44PPR62R
Capacity (LBS): 8”=300, 10”=350, 12”=450 6 2 Polyurethane on Aluminum Roller 900 7-1/4* 4 4 PA R 6 2 S 4 4 PA R 6 2 R
6 2 Polyurethane on Iron Roller 900 7-1/4* 44PIR62S 44PIR62R
6 2 Rubber on Iron Roller 410 7-1/4* 44RIR62S 44RIR62R
STANDARD TOP PLATE 6 2 Gray Rubber on Polypropylene Roller 550 7-1/4* 44TRR62S 44TRR62R
6 2 Solid Urethane Caged 900 7-1/4* 44SUC62S 44SUC62R
Mounting Bolt Hole Bolt 6 2 Solid Urethane H.D. Prec. Ball 900 7-1/4* 44SUB62S 44SUB62R
Plate Spacing Size 6 2 Solid Elastomer Prec. Ball 900 7-1/4* 44SEB62S 44SEB62R
4 x 4-1/2 2-5/8 x 3-5/8 3/8 6 2 V-Groove Iron Roller 900 7-1/4* 44VIR62S 44VIR62R
slotted to 8 2 Cast Iron Roller 1050 9-1/2 44CIR82S 44CIR82R
3x3 8 2 Phenolic Roller 1050 9-1/2 44PNR82S 44PNR82R
8 2 Polypropylene Roller 800 9-1/2 44POR82S 44POR82R
8 2 Polypropylene GP Roller 1050 9-1/2 44GPR82S 44GPR82R
#43 OPTIONAL TOP PLATE 8 2 Polyurethane on Polypropylene Roller 1000 9-1/2 44PPR82S 44PPR82R
Mounting Bolt Hole Bolt 8 2 Polyurethane on Aluminum Roller 1050 9-1/2 4 4 PA R 8 2 S 4 4 PA R 8 2 R
Plate Spacing Size 8 2 Polyurethane on Iron Roller 1050 9-1/2 44PIR82S 44PIR82R
8 2 Rubber on Iron Roller 500 9-1/2 44RIR82S 44RIR82R
5 x 5-1/2 4-1/8 x 4-1/2 3/8
8 2 Gray Rubber on Polypropylene Roller 700 9-1/2 44TRR82S 44TRR82R
8 2 Solid Urethane Caged 1050 9-1/2 44SUC82S 44SUC82R
8 2 Solid Urethane H.D. Prec. Ball 1050 9-1/2 44SUB82S 44SUB82R
8 8 Solid Elastomer Prec. Ball 1050 9-1/2 44SEB82S 44SEB82R
TO ORDER #43 TOP PLATE, CHANGE
FIRST TWO MODEL NUMBERS TO 43. KINGPINLESS MODELS ARE AVAILABLE, SEE PAGE 10

6
 50 SERIES
MEDIUM HEAVY DUTY CASTERS

Dia. Width Wheel Bearing Capacity Overall Swivel Rigid

(IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
4 1-1/2 Forged Steel Roller 1400 5-5/8 5 0 F S R 4 1 S 5 0 F S R 4 1 R
4 2 Cast Iron Roller 700 5-5/8 5 0 C I R 4 2 S 5 0 C I R 4 2 R
4 2 Phenolic Roller 800 5-5/8 5 0 P N R 4 2 S 5 0 P N R 4 2 R
4 2 Polypropylene Roller 400 5-5/8 5 0 P O R 4 2 S 5 0 P O R 4 2 R
4 2 Polypropylene GP Roller 800 5-5/8 5 0 G P R 4 2 S 5 0 G P R 4 2 R
4 2 Polyurethane on Polypropylene Roller 600 5-5/8 5 0 P P R 4 2 S 5 0 P P R 4 2 R
4 2 Polyurethane on Aluminum Roller 700 5-5/8 5 0 P A R 4 2 S 5 0 PA R 4 2 R
4 2 Polyurethane on Iron Roller 800 5-5/8 5 0 P I R 4 2 S 5 0 P I R 4 2 R
4 2 Rubber on Iron Roller 300 5-5/8 5 0 R I R 4 2 S 5 0 R I R 4 2 R
Features: 4
4
2
2
Gray Rubber on Polypropylene
Solid Urethane
Roller
Caged
300
700
5-5/8 5 0 T R R 4 2 S 5 0 T R R 4 2 R
5-5/8 5 0 S U C 4 2 S 5 0 S U C 4 2 R
Swivel Section: 4 2 Solid Elastomer Prec. Ball 1050 5-5/8 5 0 S E B 4 2 S 5 0 S E B 4 2 R
4 2 V-Groove Iron Roller 800 5-5/8 5 0 V I R 4 2 S 5 0 V I R 4 2 R
Cold-forged top plate, yoke and but-
ton are all heat treated to prevent 5 2 Forged Steel Roller 1400 6-1/2* 50FSR52S 50FSR52R
brinelling, improve swivel action and 5 2 Cast Iron Roller 1000 6-1/2* 50CIR52S 50CIR52R
5 2 Phenolic Roller 1000 6-1/2* 50PNR52S 50PNR52R
increase service life. 5 2 Polypropylene Roller 550 6-1/2* 50POR52S 50POR52R
5 2 Polypropylene GP Roller 1000 6-1/2* 50GPR52S 50GPR52R
5 2 Polyurethane on Polypropylene Roller 750 6-1/2* 50PPR52S 50PPR52R
Kingpin: 5 2 Polyurethane on Aluminum Roller 1050 6-1/2* 5 0 PA R 5 2 S 5 0 PA R 5 2 R
3/4” Diameter. 5 2 Polyurethane on Iron Roller 1050 6-1/2* 50PIR52S 50PIR52R
5 2 Rubber on Iron Roller 350 6-1/2* 50RIR52S 50RIR52R
5 2 Gray Rubber on Polypropylene Roller 450 6-1/2* 50TRR52S 50TRR52R
Axle: 5 2 Solid Urethane Caged 1000 6-1/2* 50SUC52S 50SUC52R
1/2” Diameter with lubrication fitting. 5 2 Solid Urethane H.D. Prec. Ball 1100 6-1/2* 50SUB52S 50SUB52R
5 2 Solid Elastomer Prec. Ball 1100 6-1/2* 50SEB52S 50SEB52R
5 2 V-Groove Iron Roller 800 6-1/2* 50VIR52S 50VIR52R
Finish:
6 2 Forged Steel Roller 1400 7-1/2* 50FSR62S 50FSR62R
Corrosion resistant zinc. 6 2 Cast Iron Roller 1200 7-1/2* 50CIR62S 50CIR62R
6 2 Phenolic Roller 1200 7-1/2* 50PNR62S 50PNR62R
6 2 Polypropylene Roller 700 7-1/2* 50POR62S 50POR62R
Wheel Bearings: 6 2 Polypropylene GP Roller 1200 7-1/2* 50GPR62S 50GPR62R
Straight roller bearings standard. 6 2 Polyurethane on Polypropylene Roller 900 7-1/2* 50PPR62S 50PPR62R
6 2 Polyurethane on Aluminum Roller 1200 7-1/2* 5 0 PA R 6 2 S 5 0 PA R 6 2 R
6 2 Polyurethane on Iron Roller 1200 7-1/2* 50PIR62S 50PIR62R
Options: 6 2 Rubber on Iron Roller 410 7-1/2* 50RIR62S 50RIR62R
6 2 Gray Rubber on Polypropylene Roller 550 7-1/2* 50TRR62S 50TRR62R
SL: Swivel Lock, demountable (weld-on 6 2 Solid Urethane Caged 1200 7-1/2* 50SUC62S 50SUC62R
available) 6 2 Solid Urethane H.D. Prec. Ball 1200 7-1/2* 50SUB62S 50SUB62R
6 2 Solid Elastomer Prec. Ball 1150 7-1/2* 50SEB62S 50SEB62R
CB: Cam Brake 6 2 V-Groove Iron Roller 1000 7-1/2* 50VIR62S 50VIR62R
6 2-1/2 Cast Iron Roller 1500 7-1/2 50CIR625S 50CIR625R
6 2-1/2 Phenolic Roller 1500 7-1/2 50PNR625S 50PNR625R
GS: Grease Seals 6 2-1/2 Polyurethane on Iron Roller 1500 7-1/2 50PIR625S 50PIR625R
6 2-1/2 Rubber on Iron Roller 600 7-1/2 50RIR625S 50RIR625R

* Optional
Overall
Height
5 x 2 Models
6 x 2 Models
Optional
Height
(IN)
7”
7-3/4”
Standard
Height
(IN)
6-1/2”
7-1/2”
8
8
8
8
8
8
2
2
2
2
2
2
Cast Iron
Phenolic
Polypropylene
Polypropylene GP
Polyurethane on Polypropylene
Polyurethane on Aluminum
Roller
Roller
Roller
Roller
Roller
Roller
1400
1400
800
1400
1000
1400
10-1/8*
10-1/8*
10-1/8*
10-1/8*
10-1/8*
10-1/8*
50CIR82S
50PNR82S
50POR82S
50GPR82S
50PPR82S
5 0 PA R 8 2 S
50CIR82R
50PNR82R
50POR82R
50GPR82R
50PPR82R
5 0 PA R 8 2 R
8 x 2 Models 9-1/2” 10-1/8” 8 2 Polyurethane on Iron Roller 1400 10-1/8* 50PIR82S 50PIR82R
8 2 Rubber on Iron Roller 500 10-1/8* 50RIR82S 50RIR82R
8 2 Gray Rubber on Polypropylene Roller 700 10-1/8* 50TRR82S 50TRR82R
8 2 Solid Urethane Caged 1400 10-1/8* 50SUC82S 50SUC82R
8 2 Solid Urethane H.D. Prec. Ball 1400 10-1/8* 50SUB82S 50SUB82R
8 2 Solid Elastomer Prec. Ball 1200 10-1/8* 50SEB82S 50SEB82R
8 2-1/2 Cast Iron Roller 1500 10-1/8 50CIR825S 50CIR825R
8 2-1/2 Phenolic Roller 1500 10-1/8 50PNR825S 50PNR825R
8 2-1/2 Polyurethane on Iron Roller 1500 10-1/8 50PIR825S 50PIR825R
TOP PLATE 8 2-1/2 Rubber on Iron Roller 800 10-1/8 50RIR825S 50RIR825R

Mounting Bolt Hole Bolt 10 2-1/2 Cast Iron Roller 1500 11-1/2 50CIR1025S 50CIR1025R
Plate Spacing Size 10 2-1/2 Phenolic Roller 1500 11-1/2 50PNR1025S 50PNR1025R
4-1/2 x 6-1/2 2-7/16 x 4-15/16 1/2 10 2-1/2 Polyurethane on Iron Roller 1500 11-1/2 50PIR1025S 50PIR1025R
slotted to 10 2-1/2 Rubber on Iron Roller 800 11-1/2 50RIR1025S 50RIR1025R
3-3/8 x 5-1/4
KINGPINLESS MODELS ARE AVAILABLE, SEE PAGE 10

7
 52/54 SERIES
HEAVY DUTY CASTERS

Features: #52 TOP PLATE

Swivel Section: SAE 1045 Drop-forged steel Mounting Bolt Hole Bolt
top plate and yoke base. “Deep Groove” Plate Spacing Size
load and machined component thrust race- 4x5 2-5/8 x 3-5/8 3/8
ways secured by a heat treated bolt and nut slotted to
kingpin. 3x3
Kingpin: 3/4” Diameter.
Finish: Corrosion resistant zinc.
Axle: 1/2” Diameter with lubrication fitting.
#54 TOP PLATE
Wheel Bearings: Straight roller bearings Mounting Bolt Hole Bolt
standard. Plate Spacing Size
4-1/2 x 6-1/4 2-7/16 x 4-15/16 1/2
Options: slotted to
SL: Swivel Lock 3-3/8 x 5-1/4
CB: Cam Brake
GS: Grease Seals
Delrin Bearings
Caged Bearings

Swivel Rigid Swivel Rigid

Model No. Model No. Model No. Model No.

Dia. Width Wheel Bearing Capacity Overall #52 #52 #54 #54
(IN) (IN) Type Type (LBS) HT. (IN) Top Top Top Top
Plate Plate Plate Plate
4 1-1/2 Forged Steel Roller 1200 5-5/8 52FSR41S 52FSR41R 54FSR41S 54FSR41R
4 2 Cast Iron Roller 700 5-5/8 52CIR42S 52CIR42R 54CIR42S 54CIR42R
4 2 Phenolic Roller 800 5-5/8 52PNR42S 52PNR42R 54PNR42S 54PNR42R
4 2 Polypropylene GP Roller 800 5-5/8 52GPR42S 52GPR42R 54GPR42S 54GPR42R
4 2 Polyurethane on Aluminum Roller 700 5-5/8 52PAR42S 52PAR42R 54PAR42S 54PAR42R
4 2 Rubber on Iron Roller 300 5-5/8 52RIR42S 52RIR42R 54RIR42S 54RIR42R
4 2 Solid Urethane Caged 700 5-5/8 52SUC42S 52SUC42R 54SUC42S 54SUC42R
4 2 Solid Elastomer Prec. Ball 1050 5-5/8 52SEB42S 52SEB42R 54SEB42S 54SEB42R
4 2 V-Groove Iron Roller 800 5-5/8 52VIR42S 52VIR42R 54VIR42S 54VIR42R

5 2 Forged Steel Roller 1500 6-1/2 52FSR52S 52FSR52R 54FSR52S 54FSR52R

5 2 Cast Iron Roller 1000 6-1/2 52CIR52S 52CIR52R 54CIR52S 54CIR52R
5 2 Phenolic Roller 1000 6-1/2 52PNR52S 52PNR52R 54PNR52S 54PNR52R
5 2 Polypropylene GP Roller 1000 6-1/2 52GPR52S 52GPR52R 54GPR52S 54GPR52R
5 2 Polyurethane on Aluminum Roller 1050 6-1/2 52PAR52S 52PAR52R 54PAR52S 54PAR52R
5 2 Rubber on Iron Roller 350 6-1/2 52RIR52S 52RIR52R 54RIR52S 54RIR52R
5 2 Solid Urethane Caged 1000 6-1/2 52SUC52S 52SUC52R 54SUC52S 54SUC52R
5 2 Solid Elastomer Prec. Ball 1100 6-1/2 52SEB52S 52SEB52R 54SEB52S 52SEB52R
5 2 V-Groove Iron Roller 800 6-1/2 52VIR52S 52VIR52R 54VIR52S 54VIR52R

6 2 Forged Steel Roller 1500 7-1/2 52FSR62S 52FSR62R 54FSR62S 54FSR62R

6 2 Cast Iron Roller 1200 7-1/2 52CIR62S 52CIR62R 54CIR62S 54CIR62R
6 2 Phenolic Roller 1200 7-1/2 52PNR62S 52PNR62R 54PNR62S 54PNR62R
6 2 Polypropylene GP Roller 1200 7-1/2 52GPR62S 52GPR62R 54GPR62S 54GPR62R
6 2 Polyurethane on Aluminum Roller 1200 7-1/2 52PAR62S 52PAR62R 54PAR62S 54PAR62R
6 2 Rubber on Iron Roller 410 7-1/2 52RIR62S 52RIR62R 54RIR62S 54RIR62R
6 2 Solid Urethane Caged 1200 7-1/2 52SUC62S 52SUC62R 54SUC62S 54SUC62R
6 2 Solid Elastomer Prec. Ball 1150 7-1/2 52SEB62S 52SEB62R 54SEB62S 54SUC62R
6 2 V-Groove Iron Roller 1000 7-1/2 52VIR62S 52VIR62R 54VIR62S 54VIR62R

8 2 Cast Iron Roller 1400 10-1/8 52CIR82S 52CIR82R 54CIR82S 54CIR82R

8 2 Phenolic Roller 1400 10-1/8 52PNR82S 52PNR82R 54PNR82S 54PNR82R
8 2 Polypropylene GP Roller 1400 10-1/8 52GPR82S 52GPR82R 54GPR82S 54GPR82R
8 2 Polyurethane on Aluminum Roller 1500 10-1/8 52PAR82S 52PAR82R 54PAR82S 54PAR82R
8 2 Rubber on Iron Roller 500 10-1/8 52RIR82S 52RIR82R 54RIR82S 54RIR82R
8 2 Solid Urethane Caged 1500 10-1/8 52SUC82S 52SUC82R 54SUC82S 54SUC82R
8 2 Solid Elastomer Prec. Ball 1200 10-1/8 52SEB82S 52SEB82R 54SEB82S 54SEB82R

8
 60 SERIES
HEAVY DUTY CASTERS
Features:
Swivel Section: SAE 1045
drop forged steel top plate Dia Width Wheel Bearing Capacity Overall Swivel Rigid
and yoke base. “Deep (IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
Groove” load and machined 4 3 Cast Iron Roller 2000 5-1/2 6 0 C I R 4 3 0 S 6 0 C I R 4 3 0 R
component thrust raceways 4 3 Polyurethane on Aluminum Roller 1200 5-1/2 6 0 PA R 4 3 0 S 6 0 PA R 4 3 0 R
secured by a heat treated 6 2-1/2 Forged Steel Roller 2000 7-5/8* 60FSR625S 60FSR625R
bolt and nut kingpin. 6 2-1/2 Phenolic Roller 1600 7-5/8* 60PNR625S 60PNR625R
Kingpin: 3/4” Diameter. 6 2-1/2 Polyurethane on Iron Roller 1620 7-5/8* 60PIR625S 60PIR625R
Axle: 3/4” Diameter with 6 2-1/2 V-Groove Iron Roller 2000 7-5/8* 60VIR625S 60VIR625R
lubrication fitting. 6 3 Cast Iron Roller 2000 7-5/8* 60CIR630S 60CIR630R
Finish: Corrosion resistant 6 3 Phenolic Roller 2000 7-5/8* 60PNR630S 60PNR630R
zinc. 6 3 Polyurethane on Iron Roller 2000 7-5/8* 60PIR630S 60PIR630R
Wheel Bearings: Straight 6 3 Rubber on Iron Roller 675 7-5/8* 60RIR630S 60RIR630R
roller bearings standard. 8 2-1/2 Phenolic Roller 2000 10-1/8 60PNR825S 60PNR825R
Options: 8 2-1/2 Polyurethane on Iron Roller 2000 10-1/8 6 0 P I R 8 2 5 S 6 0 P I R 8 2 5 R
SL: Swivel Lock 8 3 Forged Steel Roller 2000 10-1/8 60FSR830S 60FSR830R
WB: Wheel Brake 8 3 Cast Iron Roller 2000 10-1/8 60CIR830S 60CIR830R
8 3 Phenolic Roller 2000 10-1/8 60PNR830S 60PNR830R
#60 SWIVEL TOP PLATE 8 3 Polyurethane on Iron Roller 2000 10-1/8 60PIR830S 60PIR830R
Mounting Bolt Hole Bolt 8 3 Rubber on Iron Roller 840 10-1/8 60RIR830S 60RIR830R
8 3 V-Groove Iron Roller 2000 10-1/8 60VIR830S 60VIR830R
Plate Spacing Size
4-1/2 x 6-1/4 2-7/16 x 4-15/16 1/2 10 2-1/2 Phenolic Roller 2000 11-1/2 60PNR1025S 60PNR1025R
slotted to 10 3 Forged Steel Roller 2000 11-1/2 60FSR1030S 60FSR1030R
3-3/8 x 5-1/4 10 3 Cast Iron Roller 2000 11-1/2 60CIR1030S 60CIR1030R
10 3 Phenolic Roller 2000 11-1/2 60PNR1030S 60PNR1030R
10 3 Polyurethane on Iron Roller 2000 11-1/2 60PIR1030S 60PIR1030R
#60 RIGID TOP PLATE 10 3 Rubber on Iron Roller 1000 11-1/2 60RIR1030S 60RIR1030R

Mounting Bolt Hole Bolt

Plate Spacing Size
5 x 6-1/4 2-7/16 x 4-15/16 1/2
slotted to
* Optionalis 7-1/2”
Overall Height

3-3/8 x 5-1/4

65 SERIES
EXTRA HEAVY DUTY CASTERS
Features:
Swivel Section: SAE 1045 Dia Width Wheel Bearing Capacity Overall Swivel Rigid
drop forged steel top plate (IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
4 3 Cast Iron Roller 2000 6 65CIR430S 65CIR430R
and yoke base. “Deep
4 3 Polyurethane on Aluminum Roller 1200 6 6 5 PA R 4 3 0 S 6 5 PA R 4 3 0 R
Groove” load and machined
component thrust raceways 6 2-1/2 Forged Steel Roller 3500 8 65FSR625S 65FSR625R
secured by a heat treated 6 2-1/2 Phenolic Roller 1600 8 65PNR625S 65PNR625R
6 2-1/2 Polyurethane on Iron Roller 1620 8 65PIR625S 65PIR625R
bolt and nut kingpin.
6 2-1/2 V-Groove Iron Roller 2500 8 65VIR625S 65VIR625R
Kingpin: 1” Diameter.
Axle: 3/4” Diameter with 6 3 Cast Iron Roller 2500 8 65CIR630S 65CIR630R
lubrication fitting. 6 3 Phenolic Roller 2000 8 65PNR630S 65PNR630R
6 3 Polyurethane on Iron Roller 2040 8 65PIR630S 65PIR630R
Finish: Corrosion resistant
6 3 Rubber on Iron Roller 675 8 65RIR630S 65RIR630R
zinc.
Wheel Bearings: Straight 8 2-1/2 Phenolic Roller 2000 10-1/2 65PNR825S 65PNR825R
roller bearings standard. 8 2-1/2 Polyurethane on Iron Roller 2010 10-1/2 6 5 P I R 8 2 5 S 6 5 P I R 8 2 5 R
Options: 8 3 Forged Steel Roller 3500 10-1/2 65FSR830S 65FSR830R
SL: Swivel Lock 8 3 Cast Iron Roller 2500 10-1/2 65CIR830S 65CIR830R
WB: Wheel Brake 8 3 Phenolic Roller 2500 10-1/2 65PNR830S 65PNR830R
8 3 Polyurethane on Iron Roller 2520 10-1/2 65PIR830S 65PIR830R
8 3 Rubber on Iron Roller 840 10-1/2 65RIR830S 65RIR830R
8 3 V-Groove Iron Roller 2500 10-1/2 65VIR830S 65VIR830R
#65 TOP PLATE
10 2-1/2 Phenolic Roller 2500 12-1/2 65PNR1025S 65PNR1025R
Mounting Bolt Hole Bolt
10 3 Forged Steel Roller 3500 12-1/2 65FSR1030S 65FSR1030R
Plate Spacing Size
10 3 Cast Iron Roller 2500 12-1/2 65CIR1030S 65CIR1030R
5-1/4 x 7-1/4 3-3/8 x 5-1/4 1/2 10 3 Phenolic Roller 2900 12-1/2 65PNR1030S 65PNR1030R
slotted to 10 3 Polyurethane on Iron Roller 3000 12-1/2 65PIR1030S 65PIR1030R
4-1/8 x 6-1/8 10 3 Rubber on Iron Roller 1000 12-1/2 65RIR1030S 65RIR1030R

9
 Kingpinless
71/72 SERIES
MEDIUM DUTY CASTERS

Features: #71 TOP PLATE

Swivel Section: Patented Kingpinless single ball bearing, preci- Mounting Bolt Hole Bolt
sion machined 2-3/8” raceway, hardened to 50 Rockwell C with Plate Spacing Size
3/8” ball bearings. 4 x 4-1/2 2-5/8 x 3-5/8 3/8
Axle: 1/2” Diameter with lubrication fitting. slotted to
3x3
Finish: Corrosion resistant zinc.
Wheel Bearings: Straight roller bearings standard.
Options: #72 TOP PLATE

*
SL: Swivel Lock Mounting Bolt Hole Bolt
Optional Optional Standard
CB: Cam Brake Plate Spacing Size
Overall Height Height
SS: Stainless Steel 4-1/2 x 6-1/2 2-7/16 x 4-15/16 1/2
Height (IN) (IN)
slotted to
Delrin Bearings 8 x 2 Models 9-1/2” 10-1/8”
3-3/8 x 5-1/4
Caged Bearings

Swivel Rigid Swivel Rigid

Model No. Model No. Model No. Model No.
Dia Width Wheel Bearing Load Overall #71 #71 #72 #72
(IN) (IN ) Type Type (LBS) HT. (IN) Top Top Top Top
Plate Plate Plate Plate
4 2 Forged Steel Roller 1400 5-5/8 71FSR41S 71FSR41R 72FSR41S 72FSR41R
4 2 Cast Iron Roller 700 5-5/8 71CIR42S 71CIR42R 72CIR42S 72CIR42R
4 2 Phenolic Roller 800 5-5/8 71PNR42S 71PNR42R 72PNR42S 72PNR42R
4 2 Polypropylene Roller 400 5-5/8 71POR42S 71POR42R 72POR42S 72POR42R
4 2 Polypropylene GP Roller 800 5-5/8 71GPR42S 71GPR42R 72GPR42S 72GPR42R
4 2 Polyurethane on Polypropylene Roller 600 5-5/8 71PPR42S 71PPR42R 72PPR42S 72PPR42R
4 2 Polyurethane on Aluminum Roller 700 5-5/8 7 1 PA R 4 2 S 7 1 PA R 4 2 R 7 2 PA R 4 2 S 7 2 PA R 4 2 R
4 2 Polyurethane on Iron Roller 700 5-5/8 71PIR42S 71PIR42R 72PIR42S 72PIR42R
4 2 Rubber on Iron Roller 300 5-5/8 71RIR42S 71RIR42R 72RIR42S 72RIR42R
4 2 Gray Rubber on Polypropylene Roller 300 5-5/8 71TRR42S 71TRR42R 72TRR42S 72TRR42R
4 2 Solid Urethane Caged 700 5-5/8 71SUC42S 71SUC42R 72SUC42S 72SUC42R
4 2 Solid Elastomer Prec. Ball 1050 5-5/8 71SEB42S 71SEB42R 72SEB42S 72SEB42R
4 2 V-Groove Iron Roller 800 5-5/8 71VIR42S 71VIR42R 72VIR42S 72VIR42R

5 2 Forged Steel Roller 1500 6-1/2 71FSR52S 71FSR52R 72FSR52S 72FSR52R

5 2 Cast Iron Roller 1000 6-1/2 71CIR52S 71CIR52R 72CIR52S 72CIR52R
5 2 Phenolic Roller 1000 6-1/2 71PNR52S 71PNR52R 72PNR52S 72PNR52R
5 2 Polypropylene Roller 550 6-1/2 71POR52S 71POR52R 72POR52S 72POR52R
5 2 Polypropylene GP Roller 1000 6-1/2 71GPR52S 71GPR52R 72GPR52S 72GPR52R
5 2 Polyurethane on Polypropylene Roller 750 6-1/2 71PPR52S 71PPR52R 72PPR52S 72PPR52R
5 2 Polyurethane on Aluminum Roller 1050 6-1/2 7 1 PA R 5 2 S 7 1 PA R 5 2 R 7 2 PA R 5 2 S 7 2 PA R 5 2 R
5 2 Polyurethane on Iron Roller 1050 6-1/2 71PIR52S 71PIR52R 72PIR52S 72PIR52R
5 2 Rubber on Iron Roller 350 6-1/2 71RIR52S 71RIR52R 72RIR52S 72RIR52R
5 2 Gray Rubber on Polypropylene Roller 450 6-1/2 71TRR52S 71TRR52R 72TRR52S 72TRR52R
5 2 Solid Urethane Caged 1000 6-1/2 71SUC52S 71SUC52R 72SUC52S 72SUC52R
5 2 Solid Urethane H.D. Prec. Ball 1100 6-1/2 71SUB52S 71SUB52R 72SUB52S 72SUB52R
5 2 Solid Elastomer Prec. Ball 1100 6-1/2 71SEB52S 71SEB52R 72SEB52S 72SEB52R
5 2 V-Groove Iron Roller 800 6-1/2 71VIR52S 71VIR52R 72VIR52S 72VIR52R

6 2 Forged Steel Roller 1500 7-1/2 71FSR62S 71FSR62R 72FSR62S 72FSR62R

6 2 Cast Iron Roller 1200 7-1/2 71CIR62S 71CIR62R 72CIR62S 72CIR62R
6 2 Phenolic Roller 1200 7-1/2 71PNR62S 71PNR62R 72PNR62S 72PNR62R
6 2 Polypropylene Roller 700 7-1/2 71POR62S 71POR62R 72POR62S 72POR62R
6 2 Polypropylene GP Roller 1200 7-1/2 71GPR62S 71GPR62R 72GPR62S 72GPR62R
6 2 Polyurethane on Polypropylene Roller 900 7-1/2 71PPR62S 71PPR62R 72PPR62S 72PPR62R
6 2 Polyurethane on Aluminum Roller 1200 7-1/2 7 1 PA R 6 2 S 7 1 PA R 6 2 R 7 2 PA R 6 2 S 7 2 PA R 6 2 R
6 2 Polyurethane on Iron Roller 1200 7-1/2 71PIR62S 71PIR62R 72PIR62S 72PIR62R
6 2 Rubber on Iron Roller 410 7-1/2 71RIR62S 71RIR62R 72RIR62S 72RIR62R
6 2 Gray Rubber on Polypropylene Roller 550 7-1/2 71TRR62S 71TRR62R 72TRR62S 72TRR62R
6 2 Solid Urethane Caged 1200 7-1/2 71SUC62S 71SUC62R 72SUC62S 72SUC62R
6 2 Solid Urethane H.D. Prec. Ball 1200 7-1/2 71SUB62S 71SUB62R 72SUB62S 72SUB62R
6 2 Solid Elastomer Prec. Ball 1150 7-1/2 71SEB62S 71SEB62R 72SEB62S 72SEB62R
6 2 V-Groove Iron Roller 1000 7-1/2 71VIR62S 71VIR62R 72VIR62S 72VIR62R

8 2 Cast Iron Roller 1400 10-1/8* 71CIR82S 71CIR82R 72CIR82S 72CIR82R

8 2 Phenolic Roller 1400 10-1/8* 71PNR82S 71PNR82R 72PNR82S 72PNR82R
8 2 Polypropylene Roller 800 10-1/8* 71POR82S 71POR82R 72POR82S 72POR82R
8 2 Polypropylene GP Roller 1400 10-1/8* 71GPR82S 71GPR82R 72GPR82S 72GPR82R
8 2 Polyurethane on Polypropylene Roller 1000 10-1/8* 71PPR82S 71PPR82R 72PPR82S 72PPR82R
8 2 Polyurethane on Aluminum Roller 1500 10-1/8* 7 1 PA R 8 2 S 7 1 PA R 8 2 R 7 2 PA R 8 2 S 7 2 PA R 8 2 R
8 2 Polyurethane on Iron Roller 1500 10-1/8* 71PIR82S 71PIR82R 72PIR82S 72PIR82R
8 2 Rubber on Iron Roller 500 10-1/8* 71RIR82S 71RIR82R 72RIR82S 72RIR82R
8 2 Gray Rubber on Polypropylene Roller 700 10-1/8* 71TRR82S 71TRR82R 72TRR82S 72TRR82R
8 2 Solid Urethane Caged 1500 10-1/8* 71SUC82S 71SUC82R 72SUC82S 72SUC82R
8 2 Solid Urethane H.D. Prec. Ball 1500 10-1/8* 71SUB82S 71SUB82R 72SUB82S 72SUB82R
8 2 Solid Elastomer Prec. Ball 1200 10-1/8* 71SEB82S 71SEB82R 72SEB82S 72SEB82R

10
 Kingpinless
75 SERIES
HEAVY DUTY CASTERS
Features:
Dia Width Wheel Bearing Capacity Overall Swivel Rigid
Swivel Section: Patented (IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
Kingpinless single ball bearing 6 2-1/2 Forged Steel Roller 4000 7-1/2 75FSR625S 75FSR625R
precison machined 3” diameter 6 2-1/2 Phenolic Roller 1600 7-1/2 75PNR625S 75PNR625R
raceway hardened to 50 6 2-1/2 Polyurethane on Iron Roller 1620 7-1/2 75PIR625S 75PIR625R
Rockwell C with 1/2” ball bear- 6 2-1/2 V-Groove Iron Roller 2500 7-1/2 75VIR625S 75VIR625R
ings.
6 3 Cast Iron Roller 2500 7-1/2 75CIR630S 75CIR630R
Axle: 3/4” Diameter with lubrica-
6 3 Phenolic Roller 2000 7-1/2 75PNR630S 75PNR630R
tion fitting. 6 3 Polyurethane on Iron Roller 2040 7-1/2 75PIR630S 75PIR630R
Finish: Laguna Blue Paint 6 3 Rubber on Iron Roller 680 7-1/2 75RIR630S 75RIR630R
Wheel Bearings: Straight roller
bearings standard. 8 2-1/2 Phenolic Roller 2000 10-1/8 75PNR825S 75PNR825R
8 2-1/2 Polyurethane on Iron Roller 2010 10-1/8 7 5 P I R 8 2 5 S 7 5 P I R 8 2 5 R
Options:
8 3 Forged Steel Roller 4500 10-1/8 75FSR830S 75FSR830R
SL: Swivel Lock 8 3 Cast Iron Roller 2500 10-1/8 75CIR830S 75CIR830R
WB: Wheel Brake 8 3 Phenolic Roller 2500 10-1/8 75PNR830S 75PNR830R
8 3 Polyurethane on Iron Roller 2500 10-1/8 75PIR830S 75PIR830R
8 3 Rubber on Iron Roller 840 10-1/8 75RIR830S 75RIR830R
8 3 V-Groove Iron Roller 2500 10-1/8 75VIR830S 75VIR830R
#75 TOP PLATE
10 2-1/2 Phenolic Roller 2300 11-1/2 75PNR1025S 75PNR1025R
Mounting Bolt Hole Bolt
Plate Spacing Size 10 3 Forged Steel Roller 4500 11-1/2 75FSR1030S 75FSR1030R
4-1/2 x 6-1/2 2-7/16 x 4-15/16 1/2 10 3 Cast Iron Roller 3000 11-1/2 75CIR1030S 75CIR1030R
slotted to 10 3 Phenolic Roller 2600 11-1/2 75PNR1030S 75PNR1030R
3-3/8 x 5-1/4 10 3 Polyurethane on Iron Roller 3000 11-1/2 75PIR1030S 75PIR1030R
10 3 Rubber on Iron Roller 1000 11-1/2 75RIR1030S 75RIR1030R

Kingpinless
76 SERIES
EXTREME DUTY CASTERS
Features:
Swivel Section: Patented Dia Width Wheel Bearing Capacity Overall Swivel Rigid
Kingpinless single ball bearing (IN) (IN) Type Type (LBS) HT. (IN) Model No. Model No.
6 2-1/2 Forged Steel Roller 4000 8 76FSR625S 76FSR625R
precison machined 3” diameter 6 2-1/2 Phenolic Roller 1600 8 76PNR625S 76PNR625R
raceway hardened to 50 6 2-1/2 Polyurethane on Iron Roller 1620 8 76PIR625S 76PIR625R
Rockwell C with 1/2” ball bear- 6 2-1/2 V-Groove Iron Roller 2500 8 76VIR625S 76VIR625R
ings.
Axle: 3/4” Diameter with lubrica- 6 3 Cast Iron Roller 2500 8 76CIR630S 76CIR630R
tion fitting. 6 3 Phenolic Roller 2000 8 76PNR630S 76PNR630R
Finish: Laguna Blue Paint 6 3 Polyurethane on Iron Roller 2040 8 76PIR630S 76PIR630R
6 3 Rubber on Iron Roller 680 8 76RIR630S 76RIR630R
Wheel Bearings: Straight roller
bearings standard. 8 2-1/2 Phenolic Roller 2000 10-1/2 76PNR825S 76PNR825R
8 2-1/2 Polyurethane on Iron Roller 2010 10-1/2 7 6 P I R 8 2 5 S 7 6 P I R 8 2 5 R
Options:
SL: Swivel Lock 8 3 Forged Steel Roller 4500 10-1/2 76FSR830S 76FSR830R
8 3 Cast Iron Roller 2500 10-1/2 76CIR830S 76CIR830R
WB: Wheel Brake
8 3 Phenolic Roller 2500 10-1/2 76PNR830S 76PNR830R
8 3 Polyurethane on Iron Roller 2500 10-1/2 76PIR830S 76PIR830R
8 3 Rubber on Iron Roller 840 10-1/2 76RIR830S 76RIR830R
8 3 V-Groove Iron Roller 2500 10-1/2 76VIR830S 76VIR830R
#76 TOP PLATE
Mounting Bolt Hole Bolt 10 2-1/2 Phenolic Roller 2300 12-1/2 76PNR1025S 76PNR1025R
Plate Spacing Size
10 3 Forged Steel Roller 4500 12-1/2 76FSR1030S 76FSR1030R
5-1/4 x 7-1/4 3-3/8 x 5-1/4 1/2
10 3 Cast Iron Roller 3000 12-1/2 76CIR1030S 76CIR1030R
slotted to 10 3 Phenolic Roller 2600 12-1/2 76PNR1030S 76PNR1030R
4-1/8 x 6-1/8
12” Extreme Duty Available

11
 TM
Poly Mounts
- Standard thread sizes from 3/8-16 to 1-1/4-7. OPTIONS:
- Metric thread sizes from M-10 to M-30. Elastomer Pad Add “-EL” after Model No.
- Water and corrosion resistant. Lag Holes Delete “B” prefix from Model No.
- Steel studs or stainless steel studs.
Base Only Tapped base only, please call.
- Also available without studs (tapped base).
Stud Lengths Other lengths available.
SAE METRIC
Steel Stainless Base Stud Total Max Steel Stainless Base Stud Total Max
SAE SAE Dia. Length Length Load METRIC METRIC Dia. Length Length Load
Model No. Model No. Thread (IN) (IN) (IN) (LBS) Model No. Model No. Thread (MM) (MM) (MM) (KG)

BNYLA24 BSNYLA24 3/8-16 2 4 4-7/8 4000 BMNYLA24 BSMNYLA24 M10 50 101.6 123.2 1815
BNYLA26 BSNYLA26 3/8-16 2 6 6-7/8 4000 BMNYLA26 BSMNYLA26 M10 50 152.4 174.6 1815
BNYLB24 BSNYLB24 1/2-13 2 4 4-7/8 4000 BMNYLB24 BSMNYLB24 M12 50 101.6 123.2 1815
BNYLB26 BSNYLB28 1/2-13 2 6 6-7/8 4000 BMNYLB26 BSMNYLB26 M12 50 152.4 174.6 1815
BNYLC24 BSNYLC24 5/8-11 2 4 4-7/8 4000 BMNYLC24 BSMNYLC24 M16 50 101.6 123.2 1815
BNYLC26 BSNYLC26 5/8-11 2 6 6-7/8 4000 BMNYLC26 BSMNYLC26 M16 50 152.4 174.6 1815
BNYLA34 BSNYLA34 3/8-16 3 4 4-7/8 5000 BMNYLA34 BSMNYLA34 M10 80 101.6 123.2 2268
BNYLA36 BSNYLA36 3/8-16 3 6 6-7/8 5000 BMNYLA36 BSMNYLA36 M10 80 152.4 174.6 2268
BNYLA38 BSNYLA38 3/8-16 3 8 8-7/8 5000 BMNYLA38 BSMNYLA38 M10 80 203.2 225.4 2268
BNYLB34 BSNYLB34 1/2-13 3 4 4-7/8 5000 BMNYLB34 BSMNYLB34 M12 80 101.6 123.2 2268
BNYLB36 BSNYLB36 1/2-13 3 6 6-7/8 5000 BMNYLB36 BSMNYLB36 M12 80 152.4 174.6 2268
BNYLB38 BSNYLB38 1/2-13 3 8 8-7/8 5000 BMNYLB38 BSMNYLB38 M12 80 203.2 225.4 2268
BNYLC34 BSNYLC34 5/8-11 3 4 4-7/8 5000 BMNYLC34 BSMNYLC34 M16 80 101.6 123.2 2268
BNYLC36 BSNYLC36 5/8-11 3 6 6-7/8 5000 BMNYLC36 BSMNYLC36 M16 80 152.4 174.6 2268
BNYLC38 BSNYLC38 5/8-11 3 8 8-7/8 5000 BMNYLC38 BSMNYLC38 M16 80 203.2 225.4 2268
BNYLD34 BSNYLD34 3/4-10 3 4 4-7/8 5000 BMNYLD34 BSMNYLD34 M20 80 101.6 123.2 2268
BNYLD36 BSNYLD36 3/4-10 3 6 6-7/8 5000 BMNYLD36 BSMNYLD36 M20 80 152.4 174.6 2268
BNYLD38 BSNYLD38 3/4-10 3 8 8-7/8 5000 BMNYLD38 BSMNYLD38 M20 80 203.2 225.4 2268
BNYLB44 BSNYLB44 1/2-13 4 4 4-7/8 5000 BMNYLB44 BSMNYLB44 M12 101.6 101.6 123.2 2272
BNYLB46 BSNYLB46 1/2-13 4 6 6-7/8 5000 BMNYLB46 BSMNYLB46 M12 101.6 152.4 174.6 2272
BNYLB48 BSNYLB48 1/2-13 4 8 8-7/8 5000 BMNYLB48 BSMNYLB48 M12 101.6 203.2 225.4 2272
BNYLC44 BSNYLC44 5/8-11 4 4 4-7/8 6000 BMNYLC44 BSMNYLC44 M16 101.6 101.6 123.2 2727
BNYLC46 BSNYLC46 5/8-11 4 6 6-7/8 6000 BMNYLC46 BSMNYLC46 M16 101.6 152.4 174.6 2727
BNYLC48 BSNYLC48 5/8-11 4 8 8-7/8 6000 BMNYLC48 BSMNYLC48 M16 101.6 203.2 225.4 2727
BNYLD44 BSNYLD44 3/4-10 4 4 4-7/8 7500 BMNYLD44 BSMNYLD44 M20 101.6 101.6 123.2 3490
BNYLD46 BSNYLD46 3/4-10 4 6 6-7/8 7500 BMNYLD46 BSMNYLD46 M20 101.6 152.4 174.6 3490
BNYLD48 BSNYLD48 3/4-10 4 8 8-7/8 7500 BMNYLD48 BSMNYLD48 M20 101.6 203.2 225.4 3490
BNYLE44 BSNYLE44 1-8 4 4 4-7/8 7500 BMNYLE44 BSMNYLE44 M24 101.6 101.6 123.2 3490
BNYLE46 BSNYLE46 1-8 4 6 6-7/8 7500 BMNYLE46 BSMNYLE46 M24 101.6 152.4 174.6 3490
BNYLE48 BSNYLE48 1-8 4 8 8-7/8 7500 BMNYLE48 BSMNYLE48 M24 101.6 203.2 225.4 3490
BNYLC54 BSNYLC54 5/8-11 5 4 6-1/4 10000 BMNYLC54 BSMNYLC54 M16 127 101.6 158.8 4544
BNYLC58 BSNYLC58 5/8-11 5 8 10-1/4 10000 BMNYLC56 BSMNYLC56 M16 127 152.4 209.6 4544
BNYLD54 BSNYLD54 3/4-10 5 4 6-1/4 10000 BMNYLC58 BSMNYLC58 M16 127 203.2 260.4 4544
NEW! BNYLD58
BNYLE54
BSNYLD58
BSNYLE54
3/4-10
1-8
5
5
8
4
10-1/4
6-1/4
10000
10000
BMNYLD54
BMNYLD56
BSMNYLD54
BSMNYLD56
M20
M20
127
127
101.6
152.4
158.8
209.6
4544
4544
5” Base BNYLE58
BNYLF54
BSNYLE58
BSNYLF54
1-8
1 1/8-7
5
5
8
4
10-1/4
6-1/4
10000
10000
BMNYLD58
BMNYLE54
BSMNYLD58
BSMNYLE54
M20
M24
127
127
203.2
101.6
260.4
158.8
4544
4544
BNYLF58 BSNYLF58 1 1/8-7 5 8 10-1/4 10000 BMNYLE58 BSMNYLE58 M24 127 203.2 260.4 4544
BNYLG54 BSNYLG54 1 1/4-7 5 4 6-1/4 10000 BMNYLG54 BSMNYLG54 M30 127 101.6 158.8 4544
BNYLG58 BSNYLG58 1 1/4-7 5 8 10-1/4 10000 BMNYLG58 BSMNYLG58 M30 127 203.2 260.4 4544

Threaded Tube Ends

- Easy and cost effective way to attach mounts - Glass reinforced nylon with threaded brass insert

SQUARE TUBE ENDS ROUND TUBE ENDS

SAE SAE METRIC METRIC Tube SAE SAE METRIC METRIC Tube
Square Thread Square Thread Size Round Thread Round Thread Size
Model No. Hole Model No. Hole (IN) Model No. Hole Model No. Hole (IN)

TE1-2A 3/8-16 TE1-2MA M10 1.5 OD X .065 WALL TE1-1A 3/8-16 TE1-2MA M10 1.5 OD X .065 WALL
TE1-2B 1/2-13 TE1-2MB M12 1.5 OD X .065 WALL TE1-1B 1/2-13 TE1-2MB M12 1.5 OD X .065 WALL
TE1-2C 5/8-11 TE1-2MC M16 1.5 OD X .065 WALL TE1-1C 5/8-11 TE1-2MC M16 1.5 OD X .065 WALL
TE1-2D 3/4-10 TE1-2MD M20 1.5 OD X .065 WALL TE1-1D 3/4-10 TE1-1MD M20 1.5 OD X .065 WALL
TE1-3A 3/8-16 TE1-3MA M10 1.5 OD X .120 WALL TE1-5A 3/8-16 TE1-5MA M10 1.5 SCH. 5 PIPE
TE1-3B 1/2-13 TE1-3MB M12 1.5 OD X .120 WALL TE1-5B 1/2-13 TE1-5MB M12 1.5 SCH. 5 PIPE
TE1-3C 5/8-11 TE1-3MC M16 1.5 OD X .120 WALL TE1-5C 5/8-11 TE1-5MC M16 1.5 SCH. 5 PIPE
TE1-3D 3/4-10 TE1-3MD M20 1.5 OD X .120 WALL TE1-5D 3/4-10 TE1-5MD M20 1.5 SCH. 5 PIPE
TE2-1A 3/8-16 TE2-1MA M10 2.0 OD X .065 WALL TE1-10A 3/8-16 TE1-10MA M10 1.5 SCH. 10 PIPE
TE2-1B 1/2-13 TE2-1MB M12 2.0 OD X .065 WALL TE1-10B 1/2-13 TE1-10MB M12 1.5 SCH. 10 PIPE
TE2-1C 5/8-11 TE2-1MC M16 2.0 OD X .065 WALL TE1-10C 5/8-11 TE1-10MC M16 1.5 SCH. 10 PIPE
TE2-1D 3/4-10 TE2-1MD M20 2.0 OD X .065 WALL TE1-10D 3/4-10 TE1-10MD M20 1.5 SCH. 10 PIPE
TE2-3A 3/8-16 TE2-3MA M10 2.0 OD X .109/.120 WALL TE2-2A 3/8-16 TE2-2MA M10 2.0 OD X .065 WALL
TE2-3B 1/2-13 TE2-3MB M12 2.0 OD X .109/.120 WALL TE2-2B 1/2-13 TE2-2MB M12 2.0 OD X .065 WALL
TE2-3C 5/8-11 TE2-3MC M16 2.0 OD X .109/.120 WALL TE2-2C 5/8-11 TE2-2MC M16 2.0 OD X .065 WALL
TE2-3D 3/4/10 TE2-3MD M20 2.0 OD X .109/.120 WALL TE2-2D 3/4/10 TE2-2MD M20 2.0 OD X .065 WALL

12
 TM
Level-It
- Standard thread sizes from 10-32 to 1-1/4-7. OPTIONS: M ETRIC S IZES A VAILABLE
- Metric thread sizes from M-6 to M-30. Non-skid pad Skid resistant pad, please call.
- All studs furnished with jam nuts. Delrin With
- Hardened ball swivels 10-15o in all directions. Bolt* Delrin base construction, please
- Levels on uneven ground.
Delrin Tapped call.
- Standard yellow zinc finish; nickel, black. Base ONLY*
oxide and clear zinc finishes are available.
* Load capacities differ from specifications listed, please call.

WITH BOLT WITHOUT BOLT

Steel Stainless Base Stud Total Max Steel Stainless Base Total Max
With Bolt With Bolt Dia. Length Length Load Tapped Base Tapped Base Dia. Height Load
Model No. Model No. Thread (IN) (IN) (IN) (LBS) Model No. Model No. Thread (IN) (IN) (LBS)

BSW-0 SSW-0 1/4-20 1 1-1/4 1-61/64 1000 TSW0 STS0 1/4-20 1 45/64 1000
BSW-0A SSW-0A 1/4-20 1 2-1/2 3-13/64 1000 TSW0A STS0A 1/4-28 1 45/64 775
BSW-0B SSW-0B 1/4-28 1 1-1/4 1-61/64 775 TSW100 STS100 5/16-18 1-1/4 7/8 2300
BSW-1 SSW-1 3/8-16 1-1/4 2 2-7/8 3750 TSW101 STS101 5/16-24 1-1/4 7/8 2150
BSW-1A SSW-1A 3/8-16 1-1/4 4 4-7/8 3750 TSW1 STS1 3/8-16 1-1/4 7/8 3750
BSW-2 SSW-2 1/2-13 1-7/8 2 3-1/8 5000 TSW1A STS1A 3/8-24 1-1/4 7/8 2900
BSW-2A SSW-2A 1/2-13 1-7/8 4 5-1/8 5000 TSW2 STS2 1/2-13 1-7/8 1-1/8 5000
BSW-3 SSW-3 5/8-11 2-1/2 2 3-1/4 6000 TSW2A STS2A 1/2-20 1-7/8 1-1/8 3750
BSW-3A SSW-3A 5/8-11 2-1/2 4 5-1/4 6000 TSW3 STS3 5/8-11 2-1/2 1-1/4 6000
BSW-4 SSW-4 3/4-10 3 2 3-1/2 7400 TSW3A STS3A 5/8-18 2-1/2 1-1/4 4800
BSW-4A SSW-4A 3/4-10 3 4 5-1/2 7400 TSW4 STS4 3/4-10 3 1-1/2 7400
BSW-5 SSW-5 1-8 4 3-1/2 5-3/8 20000 TSW4A STS4A 3/4-16 3 1-1/2 5500
BSW-5A SSW-5A 1-8 4 6 7-7/8 20000 TSW5 STS5 1-8 4 1-7/8 21000
BSW-5EL SW-5EL 1-8 4 4-1/4 6-1/8 2000 TSW5A STS5A 7/8-14 4 1-7/8 7750
BSW-6 SSW-6 1-1/4-7 6 4 3-3/4 43000 TSW5B STS5B 7/8-9 4 1-7/8 6200
BSW-6EL SSW-6EL 1-1/4-7 6 6 8-3/4 43000 TSW5C STS5C 1-12 4 1-7/8 6500
TSW6 STS6 1-1/4-7 6 2-3/4 43000

TM
Steel Base Stud Min/Max
Mighty Mount With Bolt Dia. Length Load
- High level of vibration isolation for extended Model No. Thread (IN) (IN) (LBS)

machinery life. MM5028A 1/4-28 2 1-3/4 30/100

- Standard thread sizes from 1/4-28 to 1-14. MM5016B 3/8-16 2 3 100/300
MM5024B 3/8-24 2 3 100/300
- 1” of elastomer padding is oil resistant. MM80163 3/8-16 3 3 100/300
- Safety yellow finish. MM80243 3/8-24 3 3 100/300
MM80136 1/2-13 3 6 300/500
- Common applications include drill presses, MM120135 1/2-13 5 5 300/500
grinders, cnc machines, saws, presses, etc. MM120118 5/8-11 5 8 500/1500
MM160135 1/2-13 6 5 1000/4200
MM160108 3/4-10 6 8 1000/4200
MM230105 3/4-10 9 5 4000/10000
TM MM230148 1-14 9 8 4000/10000
Glide-Rite
- Standard thread sizes from 10-24 to 5/8-11. OPTIONS:
- Metric thread sizes from M-6 to M-16. Stainless Steel
- Clear zinc finish.
- Available with elastomer pad.

SAE METRIC
Steel Steel Base Stud Total Max Steel Steel Base Stud Total Max
With Pad No Pad Dia. Length Height Load With Pad No Pad Dia. Length Height Load
Model No. Model No. Thread (IN) (IN) (IN) (LBS) Model No. Model No. Thread (MM) (MM) (MM) (LBS)

G01-EL G01 10-24 1.200 1.5 2.5 250 MG01-EL MG01 M6 30.5 38.1 63.3 250
G02-EL G02 1/4-20 1.200 1.5 2.5 250 MG02-EL MG02 M8 30.5 38.1 63.3 250
G03-EL G03 5/16-18 1.200 1.5 2.5 250 MG03-EL MG03 M8 51.6 38.1 63.3 250
G04-EL G04 5/16-18 2.030 2.0 3 250 MG04-EL MG04 M10 51.6 50.8 76 250
G05-EL G05 3/8-16 2.030 2.0 3 250 MG05-EL MG05 M10 60.9 50.8 76 250
G06-EL G06 3/8-16 2.400 2.0 3 250 MG06-EL MG06 M10 60.9 101.6 126.8 250
G07-EL G07 3/8-16 2.400 4.0 5 250 MG07-EL MG07 M12 60.9 50.8 76 250
G08-EL G08 1/2-13 2.400 2.0 3 250 MG08-EL MG08 M12 60.9 101.6 126.8 250
G09-EL G09 1/2-13 2.400 4.0 5 250 MG09-EL MG09 M12 71.1 50.8 76 250
G010-EL G010 1/2-13 2.800 2.0 3 500 MG010-EL MG010 M12 71.1 101.6 126.8 500
G011-EL G011 1/2-13 2.800 4.0 5 500 MG011-EL MG011 M16 71.1 50.8 76 500
G012-EL G012 5/8-11 2.800 2.0 3 500 MG012-EL MG012 M16 71.1 101.6 126.8 500
G013-EL G013 5/8-11 2.800 4.0 5 500 MG013-EL MG013 M12 80.9 101.6 126.8 500
G014-EL G014 1/2-13 3.187 4.0 5 500 MG014-EL MG014 M12 80.9 152.4 177.6 500
G015-EL G015 1/2-13 3.187 6.0 7 500 MG015-EL MG015 M16 80.9 101.6 126.8 500
G016-EL G016 1/2-13 3.187 4.0 5 500 MG016-EL MG016 M16 80.9 152.4 177.6 500
G017-EL G017 5/8-11 3.187 6.0 7 500

13
 MATERIAL HANDLING

Features:
Heavy duty steel, aluminum, or magnesium construc-
tion.

Lift, tilt and convertible truck combinations.

Hand Trucks

Designs for every application including vending, drum

handling and more.

Capacities up to 2,000 pounds.

Features:
Wood, steel, aluminum, or fiberglass
construction.

Carpet or rubber-ended models pro-

Features:
tect cargo.
Wood, steel, aluminum, or fiber-
glass construction.
Flush or recessed styles available.
Platform Trucks

Caster and wheel combinations

Standard capacity 1,000 pounds.

Movers Dollies
for tilting, trailering, and steering
are available.

Large stock of standard sizes, with custom fabrication

available.

Capcities up to 10,000 pounds.

Floor Locks
Features:
Three position finger tip control handle which TYPE 3
includes neutral position.
Pallet Jacks

TYPE 2 TYPE 1

High strength welded steel frame.

Poly steer wheels and load rollers.

Standard capacity 5,500 pounds.

STANDARD TOP PLATE TYPE 1 TYPE 2 TYPE 3

Mounting Bolt Hole Bolt Foot pedal actuated - Kick bar release lever - Foot lever actuated
All welded construction - All welded construction - Cast aluminum alloy construction
Plate Spacing Size
Finish: Corrosion-resistant zinc Finish: Corrosion-resistant zinc Finish: Corrosion-resistant aluminum
4 x 4-1/2 2-5/8 x 3-5/8 3/8 Base: Non-skid rubber pad Base: Non-skid rubber pad Base: Non-skid rubber pad
slotted to
3x3

Type Wheel Top Operating Extended Retracted Model

Dia. (IN) Plate Height (IN) Overall HT. (IN) Overall HT. (IN) No.
50 TP TOP PLATE 1 4 Standard 5-5/8 5-5/8 5-1/16 80FTL1-4-5-5/8
Mounting Bolt Hole Bolt 2 4 Standard 5-5/8 5-5/8 5-1/16 80FTL2-4-5-5/8
1 5 Standard 6-1/2 6-1/2 5-1/2 80FTL1-5-6-1/2
Plate Spacing Size
1 6 Standard 7-1/4 7-1/4 6-1/4 80FTL1-6-7-1/4
4-1/2 x 6-1/2 2-7/16 x 4-15/16 1/2 1 6 Standard 7-1/2 7-1/2 6-1/2 80FTL1-6-7-1/2
slotted to 1 6 50 TP 7-1/2 7-1/2 6-1/2 80FTL1-6-7-1/2-50TP
3-3/8 x 5-1/4 1 8 Standard 9-1/2 9-1/2 8-1/2 80FTL1-8-9-1/2
3 4-6 Standard 6-1/2 to 7-1/2 8 5-1/2 80FTL3-46-8
3 6-8 Standard 8 to 10-1/2 11 7 80FTL3-68-11

14