ESL-HH-04-05-28

Innovative Design Concept for the

New Bangkok International Airport, NBIA
Dr. Wolfgang KESSLING Stefan HOLST Matthias SCHULER
Project Manager Director Visiting Professor Harvard University
Transsolar Energietechnik Transsolar Energietechnik Managing Director
Munich, Germany Munich, Germany Transsolar Energietechnik
kessling@transsolar.com holst@transsolar.com Stuttgart, Germany
schuler@transsolar.com

ABSTRACT the desired indoor climate conditions of 24 °C room

Thermal and visual comfort for the occupants of a temperature and 50 to 60 % relative humidity call for
room are not defined by air temperature only, but also permanent cooling and dehumidification within the
radiation with its three components solar radiation, building and a sophisticated concept for the envelope to
daylight and heat radiation has to be taken into account minimize the effects of the external solar loads.
(among other factors such as humidity, air speed and
CONCEPT DEVELOPMENT
occupant activity and clothing levels). In hot climates the
This approach was used in the design of the New
optimization of room comfort is a challenging task due
Bangkok International Airport, to develop an optimized
to the high solar radiation over the whole year.
building concept in a design team comprising the
In intelligent buildings new material developments architects, structural and mechanical engineers, HVAC,
are applied optimizing the building envelope in an acoustic and climate engineers.
integral building design process. New solutions for
For the terminal building of the NBIA with a length of
weather, noise and heat protection are developed, where
440 m and a width of 110 m the technique of shading by
building envelope and installed mechanical equipment
large overhangs was applied, but at the same time a roof
work together creating optimal comfort at minimum
created that allows daylight to pass through. Large
energy consumption.
external trellis blades that face to the south and open up
This approach was used in the design of the New to the north provide effective shading for direct sunlight
Bangkok International Airport, NBIA to develop an allowing diffuse indirect light from the sky to enter the
optimized building concept in a design team comprising building. Proper daylighting levels for the terminal hall
the architects, structural and mechanical engineers, and views through the roof to the sky in combination with
HVAC, acoustic and climate engineers. sun protection are achieved. The shading trellis blades are
naturally ventilated and located outside the building
envelope, so their absorbed solar heat does not enter the
building.

Figure 1 Model of the terminal and concourse buildings

BOUNDARY CONDITIONS
In Bangkok, the climate is characterized by
temperatures of 25 to 35 °C and a high level of relative
humidity all the year round. The annual horizontal solar Figure 2 Model of the New International Bangkok
radiation total is more than 1,500 kWh/m²a and results in Airport
a solar radiation of 1,000 W/m² on many days of the year
In this case the separation of weather and sun
with solar altitudes near the zenith.
protection layers leads to an optimized result as a starting
The situation of an international airport with 24- situation for the air conditioning in the terminal hall,
hours working days and high internal heat loads from because most of the solar radiation is prevented from
people, electric equipment and lighting combined with entering the terminal hall.
269
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 Air conditioning of large volume enclosures with ESL-HH-04-05-28
different densities and a sun protection coating the
internal building elements creates a high cooling demand intended material properties of the glass are achieved. In
in relation to the actually occupied space. In the case of the lower parts of the envelope more glazing is applied
the NBIA the total volume of the building is split into and a lower degree of fritting is used to allow a good
unconditioned zones at higher levels and cooled view to the outside. In the roof parts less glazing with a
occupied zones at low levels drastically reducing the denser frit is used to achieve good solar protection against
total cooling demand because mechanical cooling is the high sun of Thailand keeping these parts of the
applied only in spaces where it is actually needed. envelope optically transparent.
Two different mechanical systems for cooling are The membrane parts of the envelope are constructed
used. First there is a radiant floor cooling directly using a translucent multi-layer membrane assembly that
removing solar and heat radiation hitting the floor. The allows a part of the sunlight to pass as diffuse light into
floor surface stays cool and therefore thermal comfort is the building. Due to its low specific weight and its high
increased. strength these membranes can be used in wide spanning
roof constructions. The achieved savings in the amount of
The second is an air displacement system with
material used results in a cost effective building envelope
controllable air stream supplying cooled air to the room
construction. This translucent roof construction ensures
at floor level and at low velocity. The system uses a
sufficient daylighting levels for the building interior.
share of return air for the rejection of convective heat
loads and provides the room with the required amount of
cooled and dehumidified fresh air. Due to the fact that membrane
warm air rises, a thermal stratification in the hall is solar
reflection
induced, with cool air at the bottom and warm air at the fritted glass absorption 70%
28%
top, which is supported by the radiant floor cooling. The solar absorption low-e coating
reflection
conditioned zone is limited to the air volume up to a 60%
36,5%

height of 2.5 m directly above the floor in each occupied transmission

2%
space.
transmission reduced long wave radiation
3,5%

solar reflection supply air 18°C floor surface

shading louvers
60 % +sunprotection glass
Low-e coating 4 ac/h 21°C
absorption Tair= 24°C
39 %
Toperative= 27°C
13°C 19°C

transmission reduced longwave

radiation 13°C
1%
19°C
13°C 19°C Figure 4 Climate concept for the concourse areas
In addition to this, the membrane construction works
Tair= 24°C
Toperative= 27°C
displacement ventilation
supply air 18°C 1 ac/h
mixed ventilation
airconditioned
as a buffer layer for sound protection from the outside
(aircraft noise) and from the inside (room acoustics).
Between the weather protecting outer membrane made of
Figure 3 Climate concept for the terminal building
teflon coated glass fibres and the inner membrane
In the unconditioned higher levels below the roof the translucent sound baffles are mounted with an air gap on
air warms up to about ambient temperature. The both sides. This baffle layer absorbs noise from the
reduction of conditioned air volume is reducing the outside and the inside.
cooling loads of the building and also decreases the need
The inner membrane is a laminate of two layers. The
for thermal insulation of a large part of the building
layer facing the room is a low-e coated transparent foil
envelope.
being in radiative exchange with all internal surfaces of
The passenger lounges are situated in the concourse the building.
building, which adjoins the terminal and has a total
Thin metal coatings block the radiative heat exchange
length of about 3500 m. The same concept for air
between the warm membrane construction and the
conditioning is used here, but in this case the boundary
internal building parts and is transparent for daylight and
conditions are different.
sound due to its very low thickness. This low-e coated
The envelope is constructed using two different surface has an additional advantage. Instead of radiating
groups of materials which are alternating along the heat from the hot roof the radiation of the cooled floor
concourses, transparent glazed facades for outside views surfaces is reflected to the room by this low-e coating
and a translucent membrane roof for daylighting. which is improving thermal comfort for the occupants as
they thermally sense cooler surrounding surface.
The glazed parts use single laminated glass units with
different values for transmission, reflection and
absorption of solar radiation and daylight depending on
their position on the envelope. Using ceramic frit of

270
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
CONCEPT VERIFICATION BY SIMULATION To achieve a true model of such ESL-HH-04-05-28
a building, it is
The energy and ventilation concept developed by the crucial to create an accurate representation of the solar
project team was checked by simulation programs in radiation passing through the membrane roof and the
order to prove that the suggested solutions will work in fritted glass units and of the resulting heat transfer to the
reality. room. Another important aspect is the long-wave
radiative exchange between the warm inner surfaces of
A dynamic building simulation was carried out to
the enclosing walls and the floor surfaces cooled by
examine the thermal loads of the building and the change
mechanical cooling systems. The low-e layers on the
in temperature and humidity, to detect possible problems
inner side of the glass units and the membrane roof also
with condensation and to determine the expected cooling
need to be taken into account.
loads and the effects of the radiant floor cooling.
This is important for the evaluation of the heat
Furthermore, daylight simulations help evaluate
radiation entering the room, which is considerably
illuminance levels throughout the building resulting from
reduced by the layers, and of the thermal comfort,
daylight passing through the translucent / transparent
because the coolness of the floor surfaces is reflected and
building envelope, and can be used to detect problems
further lowers the mean temperature of the enclosing
with glare effects.
surfaces.
Stationary and transient fluid dynamic simulations
A dynamic finite element model of the radiant floor
(CFD) have examined the structure of the thermal
cooling was integrated into the building model so that the
stratification and the movement of humidity within the
time-dependend behaviour of the floor cooling system
building. The CFD simulations help specify ascending
can also be represented.
and descending air streams and identify the need to
separate some areas from one another with regard to air
movements.

Figure 5 Cross-section view of a typical concourse

building showing separated zones of the thermal
building model and cooled floor areas Figure 6 Radiant floor cooling system in construction
Thermal concept evaluation is based on selected For the selected floor cooling system (see Fig. 6) the
crucial parts of the building, which have been carefully chilled water pipes are arranged at a distance of 150 mm
examined in a dynamic building simulation carried out (200 mm in partly shaded areas). They are covered by a
with the simulation program TRNSYS (1). From the 7 cm thick layer of plaster and a 10 cm thick insulation
existing hourly weather data for Bangkok a period with layer beneath. The system is run with a permanent supply
extremely high daily top temperatures of 34 °C and a temperature of 13 °C and is designed for a maximum
horizontal solar radiation of 1,000 W/m² was chosen as cooling capacity of 80 W/m² and a return temperature of
the basis for comparing several concept variants. 19 °C.
The model has four thermal zones: First, an air Fig. 7 shows relevant building and system
conditioned zone, situated on the bottom level, temperatures and their change during the day. With the
comprising passenger lounges and corridors. Second, air displacement system working with a supply air
above the former, a zone with multi-level corridors and temperature of 18 °C, the air temperature in the occupied
wide-ranging people mover, which is also supplied by an areas is maintained at 24 °C as is required, while the air
air displacement system. Both zones are provided with in unconditioned areas above the occupied spaces heats
radiant floor cooling. There are two more zones above up considerably to temperatures well above the ambient
the former, which have no air conditioning, no supply air air temperature.
inlets and no discharge air outlets.

271
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 ESL-HH-04-05-28
Ambient
NBIA Concourse Case 1 Air (Conditioned Levels)
Air (Lower Unconditioned Zone) NBIA Concourse Case 1
East-West oriented, Fritted Glass 76% -> 0% Air (Higher Unconditioned Zone)
East-West oriented, Fritted Glass 76% -> 0% Total Sensible + Latent Load
constant temperature of 13°C for floor cooling Floor Cooling Inlet
225 Total Sensible Cooling Load
Floor Cooling Outlet constant inlet temperature of 13°C for floor cooling
46 realistic schedules for occupancy Surface of Cooled Floor Floor Cooling Fluid
Operative Temperature
realistic schedules for occupancy
44 Sensible Cooling Recirculating Air
200
42 Sensible Cooling Supply Air
Dehumidifcation Supply Air
40 175
38

Cooling Power in kW
36
Temperature in °C

150
34
32
125
30
28
100
26
24
75
22
20
18 50
16
14 25
12
10 0
2496 2520 2544 2496 2520 2544

Hours of Year Hours of Year

Figure 7 Building and system temperatures of a typical Figure 8 Cooling load for a typical concourse segment
concourse segment in extreme ambient conditions in extreme ambient temperatures
With convection reduced to minimum by thermal Fig. 8 shows the cooling loads to be rejected from the
stratification, heat gains by air mixing to the conditioned system in a building segment measuring 45 m in width
areas are almost completely prevented. Therefore, and 27 m in length. The total of sensible and latent
thermal insulation of the facade is only of minor cooling loads is 165 kW for this building segment.
importance so that plain glazing with its rather poor Transferring this to the building’s total occupied surface
parameters in thermal insulation can be used instead of area of 1,593 m² the cooling load to be rejected amounts
expensive high-quality insulation glass. to 104 W/m².
The indoor climate is not defined by the air The maximum dehumidification capacity for the fresh
temperature only, but also by long-wave radiation within air required for reasons of hygiene is 35 kW. As most
the room. (Other factors such as humidity and air speed flights in international air traffic are scheduled for the
are assumed to be within the comfort range. Occupant night, maximum room occupancy also happens during the
activity and clothing levels are given.) For the occupants night hours so that only 20 kW add to the peak load at
in the room the building envelope heating up during the midday. The same applies to sensible cooling of the fresh
day has the same effect as a radiant ceiling heating air down to the supply air temperature.
running at a mean surface temperature of about 55 °C at
Cooling capacity of the radiant floor cooling is
day peak.
90 kW, which is equivalent to about 55 % of the
To achieve an acceptable quality of thermal comfort maximum cooling load in the concourse segment.
under these circumstances, long-wave radiation has to be Considering the coverage of the floor surface by chilled
minimized. To this end a pyrolytic low-e layer with an water pipes of 68 % the radiant floor cooling has a
emission coefficient of 0.17 is applied to the inner glazed specific cooling capacity of 83 W/m². This is a fairly high
surfaces. This reduces long-wave thermal radiation from value, which can be achieved with a temperature
the glazed surfaces by 80 %. Furthermore, a transparent difference of only 2 Kelvin compared to the ambient,
PET foil with a metallic low-e coating featuring which results from the fact that the radiation heat that hits
enhanced resistance to scratching is applied to the the floor directly is immediately absorbed by the building
membrane roof surfaces to serve the same purpose. component before it is transferred to the air.
The floor temperature in spaces with radiant floor The remaining sensible cooling load of 55 kW is
cooling ranges between 22 °C during the day and 19 °C covered by the return air share of the air displacement
at night, thus reducing the mean radiative temperature in system. In these areas the radiant floor cooling helps
the room. The floor temperature being reflected from the reduce the required cooling capacity of the ventilation
low-e layers in the roof construction back into the room, system to about half of the former value.
affects the mean temperature of the enclosing surfaces
If a translucent / transparent building envelope like
accordingly. Adding to this the direct and diffuse solar
this one was not optimized, there may be the risk of glare
radiation that hits the occupants, an operative (sensed)
effects and the overall illuminance level may be too high,
temperature is achieved, which can be used in evaluating
thus causing disturbance to the occupants.
the thermal comfort of the room.
The aim of optimizing the envelope was to improve
During the day the maximum operative temperature
its thermal parameters and to adjust daylight incidence
is slightly above 27 °C. At night the operative
into the the building in such a way that artificial lighting
temperature is slightly below ambient air temperature,
is not required during daytime even with overcast skies
because the envelope cools down to ambient temperature
and that at the same time the overall illuminance is
and the room is further cooled by the radiant floor
reduced so that no glare effects occur.
cooling.

272
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 ESL-HH-04-05-28

Figure 9 Illuminance on the lower level of a typical

concourse segment with overcast skies
The solution is the reduction of daylight transmission Figure 10 Distribution of air temperatures in a typical
through the membrane roof sections by applying concourse segment during the day
additional sound insulation layers and reducing the
These calculations were processed by the CFD
ceramic frit density on the glazed parts from 75 % at the
program FIDAP (4), which allows the user to create a
top of the roof to zero on the walls.
perfect image of the long-wave radiative exchange
The facade structure was optimized with regard to between the surfaces within a room.
daylight transmission based on the results of detailed
Starting from the night time situation with an ambient
daylight simulations carried out with the SUPERLITE
air temperature of 25 °C and a homogeneous air
(2) and RADIANCE (3) programs in combination with
temperature of 25 °C across the whole indoor air volume,
the thermal simulations.
the outdoor temperature in the CFD simulation was raised
Fig. 9 shows the illuminance of the occupied areas on to 34 °C and a solar radiation of 900 W/m² and the
the lower level for an overcast sky in Bangkok. The maximum internal heat loads resulting from occupants
distribution of illuminance is determined by the envelope and equipment were added. A floor surface temperature
structure with an increasing share of glazed surfaces in of 22 °C as determined in thermal simulation, and a
the side walls. With light transmission rates of 2 % supply air temperature of 18 °C from the air displacement
through membrane sections and 7.5 % through glass system were used for calculations.
sections with a maximum ceramic frit densitiy an even
Transient fluid simulations examined the change in
distribution of illuminance is achieved, while only a
structure of the thermal stratification over the course of
small area between the supports of the upper level shows
time. The distribution of temperatures in the examined
a daylight illuminance of less than 300 lux, which is the
concourse segments 80 minutes after switching on the
minimum value for a working place. Daylight
day time conditions are shown in Fig. 9. In the occupied
simulations proved that the target requirement to be able
areas of the lower level and in the corridors on the upper
to go without artificial lighting even on days with
level, a lake of cool air from the displacement system
overcast sky can be met.
with a temperature of 22 to 24 °C has formed and stays
The major precondition for the feasability of the stable over the whole day.
whole energy concept is the forming of a stable thermal
Only some metres above these areas, the air
stratification in the areas without air conditioning, which
temperature rises quickly to about 30 °C. Directly under
are situated above the air conditioned areas. It is crucial
the roof a temperature of 55 °C is reached. The maximum
to safeguard that the thermal stratification cannot be
temperatures of the glazing and the membrane roof
distroyed by convection of warm air along the heated
construction can be as high as 60 °C.
facade or by other disturbances from the lower level, and
to know how long it takes the stratification to form in the The stratification of the indoor air stays stable despite
morning and what happens when the facade cools down convection resulting from air rising at the glazed facade.
in the evening. Even the overspill of cool air from the multi-level
corridors over the glass balustrades does not destroy the
To find out about this and to verify the approach to
thermal stratification. In comparable scenarios without
air movements between the areas with and without air
any floor cooling system the floor surface temperature
conditioning, extensive fluid-dynamic simulations
rises to 30 °C and completely destroys the intended
accompanied the thermal evaluation of the concept.
thermal stratification. Due to convection the whole air
Several different concourse segments were examined
volume is being mixed so that minimizing the air volume
and transient calculations were carried out to determine
to be cooled is no longer possible and the cooling demand
the stratification and de-stratification processes in the
rises considerably.
morning and in the evening.

273
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 ESL-HH-04-05-28
respectively. With pre-cooling of aircrafts and jetbridges
added the maximum demand amounts to 50.5 MW.
Transferred to an air conditioned occupied surface area of
about 375,000 m², the specific cooling demand is
135 W/m².
Optimizing the building envelope and adjusting the
cooling system (base line: mixed air-only cooling
concept) helped reduce the total cooling demand of
77 MW or 205 W/m² in the starting situation by about
35 %. Although energy input was reduced, the thermal
comfort for the occupants of the airport was considerably
improved.
The annual energy demand for the cooling system
amounts to 191 GWh/a, which is equivalent to
Figure 11 Segmentation of concourses into typical zones
513 kWh/m²a for the occupied area. The share of heat
to determine the total cooling demand of the building
covered by the radiant floor cooling is about 40 %.
50 000
Cooling Load of Entire Airport NBIA
Energy demand is reduced by about 84 GWh/a
45 000 Optimized Concept compared to the starting situation, which is equivalent to
40 000
a reduction by about 30 %.
35 000 Radiant Floor [kW]
Recirculation Air [kW]
30 000 Supply Air [kW] MATERIAL DEVELOPMENTS AND CONCEPT
Load in kW

25 000
Total Cooling Load [kW]
ANALYSIS BY MEASUREMENTS
20 000
To achieve thermal comfort in a transparent building
in the extreme climate of Thailand, the building envelope
15 000
needs to be perfectly optimized.
10 000

5 000
In cooperation with our partners in industry, the
0
findings from the simulation processes were used to
1 731 1461 2191 2921 3651 4381 5111 5841 6571 7301 8031 develop practical solutions to achieve the required optical
Hours and energetical parameters in the glass structure.
Figure 12 Annual change in cooling demand of the Fig. 13 shows the structure of optimized laminated
building for the optimized building concept glass. There is an 8 mm thick clear tempered safety glass
To determine the cooling demand for the whole pane with a double-fritt pattern of ceramic frit on the
airport, the whole building complex is segmented into inner surface with white dots to the outer and black dots
several representative zones. The terminal building was to the inner space in densities of 75 %, 65 %, 55 %, 37 %
segmented into its 6 occupied levels, and the concourses and 20 % down to zero. The ceramic frit layer is followed
were segmented into zones of typical cross-sectional by a highly selective and anti-reflective sun protection
structures and for different purposes, and all zones were coating and a 6 mm thick heat strengthened clear glass
processed in thermal simulation. pane with a pyrolytic low-e coating on the inner surface.

Fig. 11 shows the typical concourse segements that This structure shows transmission rates of 30 % in the
were examined and their occurrence in the building visible region and 15 % in the solar spectrum for glass
complex. Figures on a grey background show the sections without ceramic frit, although the light reflection
respective conditioned air volume. The total dynamic rate of such panes is not higher than that of uncoated
cooling demand of the airport was determined by glazing.
analysis of these results in the correct sequence in time.
Fig. 12 shows a graph of the annual change in
cooling demand for the whole airport as well as the share
for the radiant floor cooling, fresh air cooling and
dehumidification and the return air for the ventilation
system according to the optimized building concept. In
this diagram maximum passenger occupation of the
airport was moved to midday with maximum solar
radiation, to show that the concept will work even if
flight schedules are drastically changed.
The building has a maximum cooling demand of
44 MW, where a third is covered by radiant floor
cooling, fresh air conditioning and return air cooling Figure 13 Structure of optimized glazing

274
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 The black frit pattern on the inner surface when ANALYSIS OF THERMAL STRATIFICATION ESL-HH-04-05-28
looked at from a certain distance in the building creates The crucial step in verifying if the energy concept is
an optical effect that is similar to that of wearing sun feasible in practice was to prove by experiment that the
glasses: there is a clear undisturbed view from inside to thermal stratification is really formed as predicted by
the outside, but the brightness is reduced. This effect is fluid simulations.
facilitated by the ability of the human eye to supply the
missing information in the image. Fig. 14 shows the
view through glazing with a high ceramic frit density in
a test building.

Figure 15 Measuring indoor air movements in an indoor

tennis hall, experimental setting

Figure 14 Testing glazings with different densities of

ceramic frit
The membrane roof construction was also put into Figure 16 Verification of the forming of a stable thermal
practice in this test building. The optimized transparent stratification by a smoke test
sound absorbing layer, which was developed specifically
In summer, indoor air movements were measured in
for this project, is installed directly under a 1 mm thick
an indoor tennis hall having translucent membrane roof
glass fiber PTFE membrane functioning as an enclosure
and an air conditioning concept similar to that of the
and weather protection for the building. On the inner
project. With a length of 37 m, a width of 18 m and a
side of the roof is a thin transparent foil with a low-e
height of 7 m the tennis hall is comparable to the
coating on its inner surface. For reasons of statics the foil
concourse segments in a scale of 1:3. In the experimental
is applied to a perforated membrane, which lets the
setting shown in Fig. 15 the lower part of the hall is
internal sound pass. Daylight transmission rates of about
supplied with cooled supply air from the ventilation
2 % through the translucent membrane roof were proved
system with discharge air being removed via an air
by measurements with a coefficient of thermal
discharge, which is variable in height. Thus, no air
conductance of 2.5 W/m²K.
conditioning is applied in the upper part of the hall.
The upper part of Fig. 14 shows the membrane roof.
During a summer period with high ambient
Although light transmission rates are low, the
temperatures the system was run with parameters similar
combination of membrane construction and glazing
to those of the planned energy concept. The occupied
helped achieve a building that is bright with daylight.
area was cooled down to a temperature of 24 °C by air
conditioning and the floor was kept humid and cool,
while temperatures in the upper parts reached 30 °C.

275
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 Fig. 16 shows that the smoke test proves the forming Total Annual Costs of Energy Concepts
ESL-HH-04-05-28
of a stable stratification. 22

20
20.4
18.8 18.4
18.0

The injection of smoke into the air conditioned and 18

3.7
17.4
16.9
4.4
7.1
16
permanently exchanged air volume up to a height of
3.4
6.0
14 1.6 5.7

2.4 m on the one hand, and into the heated air volume
1.4 1.8 1.4

Mio US$/a
12 13.5
12.6
with stable stratification directly below the roof of the 10 3.2
3.0 12.1
11.9

hall results in the forming of a smoke-free layer between

8
8.8
8.2
6

the two air zones. This layer stayed stable despite a 4

Annual
Energy
Annual
Operating
Annuity of
Installation

temperature gradient that was smaller than under real 2

Costs Costs Costs

conditions and was not even disturbed by the ventilation 0

Basis Concept Cogeneration Storage Cogeneration Solar Thermal Photovoltaik
Concept Concept with Storage Concept Concept
system or occupants. Concept

This experiment proves that the fluid simulations

Figure 17 Investment costs for several energy supply
provided correct results and that the energy concept will
concepts
definitely function in reality.
Installation Costs of Energy Concepts
The measurements taken in the experimental setting 70
64.9
show that the verification of a complex concept requires 60
not only the use of a wide range of simulation 51.7
48.7
technologies, but also the support for concept 50

suggestions by experimental measurements. 40

38.0

Mio US$
31.6
28.9
30

ENERGY SUPPLY CONCEPT 20

After optimizing the energy demand of the building, 10

the energy supply for the building had to be considered,

0
and several concepts for energy supply were compared. Basis Concept Cogeneration
Concept
Storage
Concept
Cogeneration
with Storage
Solar Assisted
Concept
Photovoltaik
Concept
The existing supply concept for the new airport Concept

comprises a chilled water network with system Figure 18 Total annual costs for several energy supply
temperatures of 6 / 12 °C and chilled water generation by concepts
an electrically powered compression chiller system.
The total annual costs including not only the
This concept was compared with a co-generation investment costs broken down to an annual value, but
concept using gas turbines on the one hand, and another also the energy and operational costs for the system show
concept using absorption chiller systems on the other that the integration of a storage tank reduces the
hand. For both concepts the effect of using a chilled investment costs because of a decrease in cooling demand
water storage tank with a capacity of 285 MWh to level and annual regular costs.
out the changes in cooling demand over the course of the
day was examined. It showed that the chilled water The co-generation concept in combination with a
storage is usefull to cut cooling peaks (investment cost) storage tank accounts for the least annual costs. It is
and reduce energy cost (due to lower off peak electricity remarkable that the thermal use of solar energy produces
cost) whereas the cooling energy demand is hardly less annual costs than the conventional concept.
changed.
To evaluate the different concepts under the aspect of
Furthermore, the use of highly efficient solar ecology, the concept using regenerative solar energy and
collectors covering a surface area of 35,000 m² in the approach for an efficient use of energy by co-
combination with an absorption chiller system and gas generation were compared to the conventional concept
heating as a back-up system was examined. Under using an electrically powered vapour compression chiller
climatic conditions as in Thailand with high solar system in combination with a storage tank.
radiation, high-efficiency evacuated tube collectors with
CPC reflectors can be used to generate a temperature of
190 °C required for the operation of a double-effect
absorption chiller system.
A concept using photovoltaic modules covering a
surface area of 55,000 m² for the immediate generation
of electric power in combination with an electrically
powered compression chiller system was compared to
other concepts under the aspect of economy. Fig. 17
shows the investment costs for severel different
concepts.

276
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004
 DESIGN - TEAM ESL-HH-04-05-28
Annual CO2 Savings
60 000
55 000
Systems compared to Energy Storage System
Total Annual CO2 Emission: 217 634 t/a
Architects: Murphy / Jahn Architects,
50 000
CO2 Emission of Electricity Production : 0.629 t/MWhel
Chicago
Annual CO2 Reduction in t/a Project Management: TAMS, Chicago
45 000
- 18.9 % - 18.9 %
40 000
35 000 Structural engineers: Werner Sobek Ingenieure,
30 000 Stuttgart
25 000
20 000
Energy, comfort: Transsolar Energietechnik GmbH,
15 000 Stuttgart
10 000
5 000
- 3.3 %
- 1.5 %
HVAC engineers: Flack+Kurtz Consulting Engineers
0 San Franscisco
Photovoltaic System Solar Thermal Cogeneration without Cogeneration System Acoustics: Laboratorium für Optik und
Collectors Storage
Dynamik, Dr. R. Blum, Leonberg
Figure 19 CO2 reduction potential for several energy SIMULATION PROGRAMS USED FOR ANALYSIS
supply concepts (1) TRNSYS 14.2, A Transient System Simulation
Program, Solar Energy Laboratory, University of
Cost of CO2 Savings Wisconsin, Madison, U.S.A. 1996
Systems compared to Energy Storage System
475

425 413
CO2 Emission of Electricity Production : 0.629 t/MWhel
(2) SUPERLITE, Adeline 2.0 IEA Solar Heating and
375
Cooling Program ,Task 12
Cost in US $ per ton CO 2

325 306

275
(3) RADIANCE , Lighting Systems Research Group,
225 Lawrence Berkeley Laboratory
175

125
(4) FIDAP 7.52, Fluid Dynamics International,
75 Evanston, Illinois, U.S.A.
25 14
-11
-25
Photovoltaic System Solar Thermal Cogeneration without Cogeneration System
Collectors Storage

Figure 20 Specific costs for the reduction of CO2

emissions for several energy supply concepts
Fig. 19 shows that with the determined specific CO2
emissions for power production in Thailand, co-
generation of power and refrigeration achieves
considerably higher reductions in CO2 emissions than the
use of solar energy.
When the total annual reduction in CO2 emissions is
divided by the additional annual costs for each system,
the result are the specific costs for reducing emissions by
one tonne of CO2 (see Fig. 20).
For the co-generation concept, costs for the reduction
of CO2 emissions are very low, or even negative if the
storage tank is used, which means that this concept
provides the required amount of energy at lower costs
than the other concept. As a consequence, this energy
supply concept featuring very favourable ecological
parameters is strongly recommended for the airport.
For additional investment costs energy contractors
can provide preliminary financing without charges for
the constructor.
This study shows that not only under the aspect of
investment costs, but also with regard to costs for
environmentally friendly systems, optimized innovative
concepts using thermal solar collectors should be given
preference over systems using photovoltaics technology.

277
Proceedings of the Fourteenth Symposium on Improving Building Systems in Hot and Humid Climates, Richardson, TX, May 17-20, 2004