INTEGRATED CIRCUITS

74ALS151
8-input multiplexer

Product specification 1991 Feb 08

IC05 Data Handbook


 
 
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

FEATURES PIN CONFIGURATION

• 8-to-1 multiplexing
• On chip decoding I3 1 16 VCC

• Multi-function capability I2 2 15 I4

• Complementary outputs
I1 3 14 I5

I0 4 13 I6
• See 74ALS251 for 3-State version Y 5 12 I7

Y 6 11 S0

DESCRIPTION E 7 10 S1
The 74ALS151 is a logic implementation of a single 8-position GND 8 9 S2
switch with the switch position controlled by the state of three select
(S0, S1, S2) inputs. True (Y) and complementary (Y) outputs are SF00742
both provided.
The enable (E) is active-Low. When E is High, Y output is Low and ORDERING INFORMATION
the Y output is High regardless of all other inputs.
ORDER CODE
DESCRIPTION COMMERCIAL RANGE DRAWING
TYPICAL VCC = 5V ±10%, NUMBER
TYPICAL
TYPE SUPPLY CURRENT Tamb = 0°C to +70°C
PROPAGATION DELAY
(TOTAL)
16-pin plastic DIP 74ALS151N SOT38-4
74ALS151 8.0ns 8.0mA 16-pin plastic SO 74ALS151D SOT109-1

INPUT AND OUTPUT LOADING AND FAN-OUT TABLE

74ALS (U.L.) LOAD VALUE
PINS DESCRIPTION
HIGH/LOW HIGH/LOW
I0 – I7 Data inputs 1.0/1.0 20µA/0.1mA
S0 – S2 Select inputs 1.0/1.0 20µA/0.1mA
E Enable input (active-Low) 1.0/1.0 20µA/0.1mA
Y, Y Data outputs 130/240 2.6mA/24mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.

LOGIC SYMBOL IEC/IEEE SYMBOL

4 3 2 1 15 14 13 12 7 MUX
EN
11
0
10
0 5
I0 I1 I2 I3 I4 I5 I6 I7 9 G
7
4 2
11 S0
3 6
10 S1
2
9 S2
1
7 E
15
Y Y
14
13
12
VCC = Pin 16 5 6
GND = Pin 8
SF00743 SF00744

1991 Feb 08 2 853–1022 01670

Philips Semiconductors Product specification

8-input multiplexer 74ALS151

LOGIC DIAGRAM

I0 I1 I2 I3 I4 I5 I6 I7
4 3 2 1 15 14 13 12
9
S2

10
S1

11
S0

7
E

5 6
VCC = Pin 16
GND = Pin 8 Y Y
SF00741

FUNCTION TABLE
INPUTS OUTPUTS
S2 S1 S0 E Y Y
X X X H L H
L L L L I0 I0
L L H L I1 I1
L H L L I2 I2
L H H L I3 I3
H L L L I4 I4
H L H L I5 I5
H H L L I6 I6
H H H L I7 I7
H = High voltage level
L = Low voltage level
X = Don’t care

1991 Feb 08 3
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

ABSOLUTE MAXIMUM RATINGS

(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL PARAMETER RATING UNIT
VCC Supply voltage –0.5 to +7.0 V
VIN Input voltage –0.5 to +7.0 V
IIN Input current –30 to +5 mA
VOUT Voltage applied to output in High output state –0.5 to VCC V
IOUT Current applied to output in Low output state 48 mA
Tamb Operating free-air temperature range 0 to +70 °C
Tstg Storage temperature range –65 to +150 °C

RECOMMENDED OPERATING CONDITIONS

SYMBOL PARAMETER LIMITS UNIT
MIN NOM MAX
VCC Supply voltage 4.5 5.0 5.5 V
VIH High-level input voltage 2.0 V
VIL Low-level input voltage 0.8 V
IIk Input clamp current –18 mA
IOH High-level output current –2.6 mA
IOL Low-level output current 24 mA
Tamb Operating free air temperature range 0 +70 °C

DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS1 UNIT
MIN TYP2 MAX

VCC = ±10%,, VIL = MAX,, IOH = –0.4mA VCC – 2 V

VOH
O High level output voltage
High-level VIH = MIN IOH = MAX 2.4 3.2 V

VCC = MIN,, VIL = MAX,, IOL = 12mA 0.25 0.40 V

VOL
O Low level output voltage
Low-level VIH = MIN IOL = 24mA 0.35 0.50 V
VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.5 V
II Input current at minimum input voltage VCC = MAX, VI = 7.0V 0.1 mA

IIH High-level input current VCC = MAX, VI = 2.7V 20 µA

IIL Low-level input current VCC = MAX, VI = 0.4V –0.1 mA

IO Output current3 VCC = MAX, VO = 2.25V –30 –112 mA
ICC Supply current (total) VCC = MAX 8.0 12 mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS.

1991 Feb 08 4
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

AC ELECTRICAL CHARACTERISTICS
LIMITS
Tamb = 0°C to +70°C
SYMBOL PARAMETER TEST CONDITION VCC = +5.0V ± 10% UNIT
CL = 50pF, RL = 500Ω

MIN MAX
tPLH Propagation delay 3.0 12.0
Waveform 1 ns
tPHL In to Y 5.0 12.0
tPLH Propagation delay 3.0 15.0
Waveform 2 ns
tPHL In to Y 5.0 15.0
tPLH Propagation delay 5.0 15.0
Waveform 1, 2 ns
tPHL Sn to Y 7.0 16.0
tPLH Propagation delay 5.0 15.0
Waveform 1, 2 ns
tPHL Sn to Y 5.0 16.0
tPLH Propagation delay 4.0 12.0
Waveform 1 ns
tPHL E to Y 4.0 12.0
tPLH Propagation delay 4.0 12.0
Waveform 1 ns
tPHL E to Y 5.0 14.0

AC WAVEFORMS
For all waveforms, VM = 1.3V.

VIN
VIN VM VM
VM VM

tPLH tPHL
tPHL tPLH

VM VM
VOUT VM VM VOUT

SF00093 SF00092

Waveform 1. Propagation Delay for Inverting Output Waveform 2. Propagation Delay for Non-inverting Output

TEST CIRCUIT AND WAVEFORMS

VCC tw AMP (V)

90% 90%
NEGATIVE
VM VM
PULSE
VIN VOUT 10% 10%
0.3V
PULSE D.U.T.
GENERATOR tTHL (tff) tTLH (tr )

RT CL RL tTLH (tr ) tTHL (tf )

AMP (V)
90% 90%
POSITIVE
PULSE VM VM
Test Circuit for Totem-pole Outputs 10% 10%
tw 0.3V

Input Pulse Definition

DEFINITIONS:
RL = Load resistor; INPUT PULSE REQUIREMENTS
see AC electrical characteristics for value. Family
CL = Load capacitance includes jig and probe capacitance; Amplitude VM Rep.Rate tw tTLH tTHL
see AC electrical characteristics for value.
RT = Termination resistance should be equal to ZOUT of 74ALS 3.5V 1.3V 1MHz 500ns 2.0ns 2.0ns
pulse generators.
SC00005

1991 Feb 08 5
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

1991 Feb 08 6
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

1991 Feb 08 7
Philips Semiconductors Product specification

8-input multiplexer 74ALS151

DEFINITIONS
Data Sheet Identification Product Status Definition

This data sheet contains the design target or goal specifications for product development. Specifications
Objective Specification Formative or in Design
may change in any manner without notice.

This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Preliminary Specification Preproduction Product Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.

This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
Product Specification Full Production
at any time without notice, in order to improve design and supply the best possible product.

Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.

LIFE SUPPORT APPLICATIONS

Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.

Philips Semiconductors  Copyright Philips Electronics North America Corporation 1997

811 East Arques Avenue All rights reserved. Printed in U.S.A.
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381


 
 
1991 Feb 08 8
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.