Rexton - Service Manual - ENGINE PDF

ENGINE
SERVICE MANUAL
PYUNGTAEK, KOREA
SECTION INDEX
SERVICE VOLUME 1 OF 2
MANUAL(vol. 1 of 2) GENERAL INFORMATION DI0A
REXTON ENGINE ASSEMBLY DI01
ENGINE HOUSING DI02
INTAKE SYSTEM DI03

FOREWORD
This manual includes procedure for maintenance, EXHAUST SYSTEM DI04

adjustment, service operation and removal and
installation of components.
All information, illustrations and specifications LUBRICATION SYSTEM DI05
contained in this manual are based on the latest
product information available at the time of manual
approval.
The right is reserved to make changes at any time COOLING SYSTEM DI06
without notice.
FUEL SYSTEM DI07
ENGINE CONTROL SYSTEM DI08
ELECTRIC DEVICES AND

SENSORS DI09
SSANGYONG MOTOR CO., LTD.

DIAGNOSIS DI10
PYUNGTAEK, KOREA
DI ENGINE
CONTENTS
GENERAL INFORMATION .................... DI0A
ENGINE ASSEMBLY ............................. DI01

ENGINE HOUSING ................................ DI02
INTAKE SYSTEM................................... DI03
EXHAUST SYSTEM............................... DI04

LUBRICATION SYSTEM ....................... DI05
COOLING SYSTEM ............................... DI06
FUEL SYSTEM ...................................... DI07

ENGINE CONTROL SYSTEM ............... DI08
ELECTRIC DEVICES AND SENSORS . DI09
DIAGNOSIS ........................................... DI10

SECTION DI0A
GENERAL INFORMATION
DI0A-1
SECTION
00 DI0A
GENERAL INFORMATION
Table of Contents
CLEANNESS ....................................... DI0A-3 FUEL SYSTEM ................................. DI0A-21
STRUCTURE ...................................... DI0A-8 Fuel supply system ...................... DI0A-22

GENERAL SPECIFICATIONS ........... DI0A-23
ENGINE CONTROLS ....................... DI0A-11
Vehicle specifications ................... DI0A-23
ECU related components .............. DI0A-11
Maintenance ................................ DI0A-26
Engine and sensors ..................... DI0A-12
Electrical components and VEHICLE IDENTIFICATION .............. DI0A-28
pre heating system ...................... DI0A-13
HOW TO USE AND MAINTAIN WORKSHOP
INTAKE SYSTEM ............................. DI0A-14 MANUAL ........................................... DI0A-30
Intake air flow chart ...................... DI0A-15 Consists of workshop manual ...... DI0A-30
INTAKE SYSTEM ............................. DI0A-16 Manual description ...................... DI0A-30
Guidelines for service work
Exhaust air flow chart ................... DI0A-17
safety ........................................... DI0A-31
LUBRICATION SYSTEM .................. DI0A-18 Lifting points ................................. DI0A-36
COOLING SYSTEM ......................... DI0A-19 Tightening torque of standard
bolts .............................................. DI0A-37
Coolant flow chart ........................ DI0A-20
GENERAL INFORMATION CHANGED BY

DI ENG SM - 2004.4 EFFECTIVE DATE
AFFECTED VIN
DI0A-3
CLEANNESS
Cleanness of DI Engine Fuel System and Service Procedures
The fuel system for DI engine consists of transfer (low pressure) line and high pressure line. Its highest pressure
reaches over 1600 bar. Some components in injector and HP pump are machined at the micrometer 100 µm of
preciseness. The pressure regulation and injector operation are done by electric source from engine ECU.
Accordingly, if the internal valve is stucked due to foreign materials, injector remains open. Even in this case, the
HP pump still operates to supply high pressurized fuel. This increases the pressure to combustion chamber (over
250 bar) and may cause fatal damage to engine.
You can compare the thickness of injector nozzle hole and hair as shown in below figure (left side). The right side
figure shows the clearance between internal operating elements.
Valve actuator lift: 0.028 mm

Hair
Diameter: 0.40 mm
Operating
clearance:
Nozzle hole 0.002 mm
Diameter:
2.0 mm
Y220_0A035
The core elements of fuel system has very high preciseness that is easily affected by dust or very small foreign
material. Therefore, make sure to keep the preliminary works and job procedures in next pages. If not, lots of
system problems and claims may arise.

AFFECTED VIN
DI0A-4
Job procedures
1. Always keep the workshop and lift clean (especially, from dust).
2. Always keep the tools clean (from oil or foreign materials).
3. Wear a clean vinyl apron to prevent the fuzz, dust and foreign materials from getting into fuel system. Wash
your hands and do not wear working gloves.
4. Follow the below procedures before starting service works for fuel system.
Carefully listen the symptoms and problems from customer.
Visually check the leaks and vehicle appearance on the wiring harnesses
and connectors in engine compartment.
Perform the diagnosis proceee with Scan-i

(refer to “DIAGNOSIS” section in this manual).
Locate the fault. If the cause is from fuel system (from priming pump to
injector, including return line), follow the step 1 through step 3 above.
5. If the problem is from HP pump, fuel supply line or injector, prepare the clean special tools and sealing caps
to perform the diagnosis for DI engine fuel system in “DIAGNOSIS” section in this manual. At this point,
thoroughly clean the related area in engine compartment.
Notice
Clean the engine compartment before starting service works.
Tool kit for high pressure line Took kit for low pressure line Removal tool box and cap kits
CHANGED BY GENERAL INFORMATION

EFFECTIVE DATE DI ENG SM - 2004.4
AFFECTED VIN
DI0A-5
6. Follow the job procedures. If you find a defective component, replace it with new one.
Disconnect the negative battery cable.
For safety reasons: check pressure is low before opening the HP systems (pipes)
Use special tools and torque wrench to perform the correct works.
Once disconnected, the fuel pipes between HP pump and fuel rail and between fuel rail
and each injector should be replaced with new ones. The pipes should be tightened to
specified tightening torques during installation. Over or under torques out of specified
range may cause damages and leaks at connections. Once installed, the pipes have been
deformed according to the force during installtion, therefore they are not reusable.
The copper washer on injector should be replaced with new one. The injector holder bolt
should be tightened to specified tightening torque as well. If not, the injection point may be
deviated from correct position, and it may cause engine disorder.
Plug the disconnected parts with sealing caps, and remove the caps immediately
before replacing the components.
Fuel pressure sensor
High pressure pump Common rail
IMV valve
Transfer pump and high Injection
pressure pump pipe
Fuel temperature sensor
Water separator
Water detection sensor
Priming
pump
Fuel filter
Injector
Cap position
Supply line
Return line
Fuel tank
Y220_0A039

AFFECTED VIN
DI0A-6
7. Plug the removed components with clean and

undamaged sealing caps and store it into the box to
keep the conditions when it was installed.
8. Clear the high pressure offset value by Scan-100 after
replacing the high pressure pump.
Y220_0A040
9. To supply the fuel to transfer line of HP pump press

the priming pump until it becomes hard.
Warning
Do not crank engine before having filled pump.

Priming pump
Y220_0A041
10. Check the installed components again and connect

the negative battery cable. Start the engine and check
the operating status.
11. With Scan-i, check if there are current faults and erase
the history faults.
Note
For details, refer to “DI10 Diagnosis teable”.
Y220_0A042

AFFECTED VIN
DI0A-7
DI Engine and Its Expected Problems and Remedies Can be Caused

by Water in Fuel
SYSTEM SUPPLEMENT AGAINST PARAFFIN SEPARATION.

In case of Diesel fuel, paraffin, one of the elements, can be separated from fuel during winter and then can stick on
the fuel filter blocking fuel flow and causing difficult starting finally. Oil companies supply summer fuel and winter
fuel by differentiating mixing ratio of kerosene and other elements by region and season. However, above phenomenon
can be happened if stations have poor facilities or sell improper fuel for the season.
In case of DI engine, purity of fuel is very important factor to keep internal preciseness of HP pump and injector.
Accordingly, more dense mesh than conventional fuel filter is used. To prevent fuel filter internal clogging due to
paraffin separation, SYMC is using fuel line that high pressure and temperature fuel injected by injector returns
through fuel filter to have an effect of built-in heater (see fuel system).
SYSTEM SUPPLEMENT AND REMEDY AGAINST WATER IN FUEL

As mentioned above, some gas stations supply fuel with
excessive than specified water. In the conventional IDI
engine, excessive water in the fuel only causes dropping
engine power or engine hunting. However, fuel system in
the DI engine consists of precise components so water in
the fuel can cause malfunctions of HP pump due to poor
lubrication of pump caused by poor coating film during high
speed pumping and bacterization (under long period parking).
To prevent problems can be caused by excessive water in
fuel, water separator is installed inside of fuel filter. When
fuel is passing filter, water that has relatively bigger specific
gravity is accumulated on the bottom of the filter.
Y220_0A041
If water in the separator on the fuel filter exceeds a certain level, it will be supplied to HP pump with fuel, so the
engine ECU turns on warning light ( ) on the meter cluster and buzzer if water level is higher than a certain level.
Due to engine layout, a customer cannot easily drain water from fuel filter directly, so if a customer checks in to
change engine oil, be sure to perform water drain from fuel filter. (See fuel system for details.)

AFFECTED VIN
DI0A-8
STRUCTURE
Front view
Rear view
Y220_0A001
1. TVD (Torsional Vibration Damper) 7. Cooling fan pulley & viscos clutch 13. Oil filter housing
2. Air conditioner compressor 8. Aut tensioner pulley 14. Vacuum pump
3. Power steering pump pulley 9. Auto tensioner 15. Crank position sensor
4. Idle pulley 10. Poly-groove belt 16. EGR valve
5. Water pump pulley 11. Cam position sensor 17. Power steering pump
6. Alternator 12. Drive plate (M/T: DMF) 18. EGR center pipe

AFFECTED VIN
DI0A-9
Top view
Y220_0A002
19. Cylinder head cover 24. Fuel pipe 29. Booster pressure sensor
20. Intake manifold 25. Injector 30. Oil separator
21. Water outlet port 26. Fuel return line 31. Oil dipstic
22. Common rail 27. Oil filler cap 32. EGR center pipe
23. Fuel pressure sensor 28. Glow plug

AFFECTED VIN
DI0A-10
Left side view
Right side view
Y220_0A003
33. Cylinder head 38. EGR - RH pipe 42. Turbocharger vacuum modulator
34. Cylinder block 39. Oil separator 43. EGR valve vacuum modulator
35. Oil pan 40. Oil dipstic 44. EGR valve
36. Drain plug 41. HP pump 45. Exhaust manifold
37. Turbocharger

AFFECTED VIN
DI0A-11
ENGINE CONTROLS
ECU RELATED COMPONENTS
Fuel filter
ECU/barometric sensor Cam position sensor (water detection sensor) Accelerator pedal sensor
HFM sensor/intake air Pre heating time relay Main relay

temperature sensor
Y220_0A004

AFFECTED VIN
DI0A-12
ENGINE AND SENSORS
Crankshaft position
Injector Common rail
sensor
Glow plug Fuel pressure sensor
Camshaft position Booster pressure sensor

sensor
HP pump Coolant temperature Knock sensor (2)

sensor
Y220_0A005

AFFECTED VIN
DI0A-13
ELECTRICAL COMPONENTS AND PRE HEATING SYSTEM
Glow plug Pre heating time relay
Fuse box Battery
Starter motor Alternator
Y220_0A006

AFFECTED VIN
DI0A-14
INTAKE SYSTEM
Air cleaner assembly HFM sensor Intake duct hose Intake manifold
Intake outlet hose Turbocharger Intercooler Inlet hose
Y220_0A007

AFFECTED VIN
DI0A-15
INTAKE AIR FLOW CHART
Intake valve (in combustion chamber)
Intake manifold
Air cleaner side
Turbo-
charger Engine
(compressor)
HFM sensor
Intake hose (outlet) Intercooler Intake hose (inner)
Y220_0A008

AFFECTED VIN
DI0A-16
INTAKE SYSTEM
Muffler Exhaust manifold EGR valve
Turbocharger Catalytic converter EGR pipe Vacuum modulator
Y220_0A009

AFFECTED VIN
DI0A-17
EXHAUST AIR FLOW CHART
Catalytic converter Exhaust pipe Muffler
Ambient
air
Exhaust gas
Turbocharger
(turbine side)
EGR vacuum
modulator
To turbocharger
booster
Turbocharger
booster vacuum
modulator
Turbocharger booster EGR valve
Exhaust manifold
EGR pipe
Y220_0A010

AFFECTED VIN
DI0A-18
LUBRICATION SYSTEM
Cylinder head cover Oil dipstic PCV valve Engine oil filter
housing
Engine oil pump Oil pan Engine oil cooler Engine oil pressure
switch
Y220_0A011

AFFECTED VIN
DI0A-19
COOLING SYSTEM
Coolant reservoir Water pump
Radiator assembly Cooling fan and fan

clutch
Y220_0A013

AFFECTED VIN
DI0A-20
COOLANT FLOW CHART
Heater
Oil cooler
Coolant reservoir Intake manifold
Thermostat
Coolant outlet port
Water pump
Inner hose Outlet hose
Cooling fan
Radiator
Y220_0A014

AFFECTED VIN
DI0A-21
FUEL SYSTEM
Fuel return hose Fuel pressure pipe Common rail Fuel filter
Injector HP pump Priming pump
Y220_0A015

AFFECTED VIN
DI0A-22
FUEL SUPPLY SYSTEM
High pressure pump Common rail
IMV valve
Low and high High
pressure
pressure pump
pipe
Fuel temperature
sensor
Water separator
Label
Fuel filter Prining pump (C21)
Water detection
sensor
Injector
Sensors
HFM sensor
Cam position sensor
Crank position sensor
Fuel tank ECU
Knock sensor etc.
Components:
Supply line
- High pressure fuel pump - Fuel rails - Fuel pressure sensor Return line
- Fuel injectors - Electroc control unit (ECU) - Various sensors and actuators ECU communication line
Y220_0A016
According to input signals from various sensors, engine ECU calculates driver’s demand (position of the accelerator
pedal) and then controls overall operating performance of engine and vehicle on that time.
ECU receives signals from sensors via data line and then performs effective engine air-fuel ratio controls based on those
signals. Engine speed is measured by crankshaft speed (position) sensor and camshaft speed (position) sensor deter-
mines injection order and ECU detects driver’s pedal position (driver’s demand) through electrical signal that is gener-
ated by variable resistance changes in accelerator pedal sensor. Air flow (hot film) sensor detects intake air volume and
sends the signals to ECU. Especially, the engine ECU controls the air-fuel ratio by recognizing instant air volume
changes from air flow sensor to decrease the emissions (EGR valve control). Furthermore, ECU uses signals from
coolant temperature sensor and air temperature sensor, booster pressure sensor and barometric sensor as compensa-
tion signal to respond to injection starting, pilot injection set values, various operations and variables.

AFFECTED VIN
DI0A-23
GENERAL SPECIFICATIONS
VEHICLE SPECIFICATIONS
Vehicle Dimension (mm)
Y220_0A017

AFFECTED VIN
DI0A-24
Specifications
Systems Items Diesel Remark
General Overall length (mm) 4,720 (4,785) ( ): optional
Overall width (mm) 1,870 item
Overall height (mm) 1,760 (1,830)

Gross vehicle weight (kg) AT: 2450 (2510), MT: 2405 (2465)
Curb weight (kg) AT: 1995 (2055), MT: 1950 (2010)
Min. turning radius (m) 5.6
Ground clearance (mm) 200
Fuel Diesel
Fuel tank capacity 80
Engine Model D27DT
No. of cyl./Compression ratio 5/18:1
Total displacement 2,696 cc
Camshaft arrangement DOHC
Max. power 170 ps/4,000 rpm
Max. torque 34.7 kg•m/1,800 rpm
Injection timing ATDC 4° ± 1°(at idle)
Idle speed 760 ± 50 rpm
Cooling system Water-cooled/forced circulation
Coolant capacity Approx. 11.5
Lubrication Gear pump, forced circulation
Max. oil capacity 9.3
Turbo charger and cooling type Turbo charger, air-cooled
Manual Type Remote control, floor change type
transmission 1st IDI Engine 4.007 DI Engine 4.315
2nd 2.367 2.475
rd
3 1.473 1.536
th
4 1.000 1.000
5th 0.872 0.807
Rev. 3.700 3.591
Automatic Model Electronic
transmission Type Floor change type
1st 2.742 3.595 2.742
2nd 1.508 2.186 1.508
rd
3 1.000 1.405 1.000
th
4 0.708 1.000 0.708
5th - 0.831 -
Rev. 1st 2.429 3.162 2.429
nd
Rev. 2 - 1.926 -

AFFECTED VIN
DI0A-25
Specifications (Cont’d)
Systems Items Diesel Remark
Transfercase Model Part-time ( ): optional item
Type Planetary gear type
Gear ratio High 1.000 : 1
Low 2.483 : 1
Clutch Type Hydraulic [A/T: Torque converter]
Disc type Dry single diaphragm type
[A/T: 3 elements 1 stage 2 phases]
Power Type Rack and pinion
steering Steering angle Inner 36° 17'
Outer 32° 40'
Front axle Drive shaft type Ball joint type
Axle housing type Build-up type
Rear axle Drive shaft type Semi-floating type
Axle housing type Build-up type
Brake Master cylinder type Tandem type
Booster type Vacuum booster
Type Inner Disc
Outer Drum (Disc)
Parking brake Cable type (internal expansion)
Suspension Front Wishbone + Coil spring
Rear 5-link + Coil spring
Air Refrigerant R134a
conditioner Compressor type Vane type
Electrical Battery type/Capacity (V-AH) MF / 12 - 90
Starter capacity (V-kW) Diesel : 12 - 2.2, Gasoline : 12 - 1.8
Alternator capacity (V-A) IDI 12 - 75 (12 - 90)
DI 12 - 140 (12 - 115)
Gasoline 12 - 115

AFFECTED VIN
DI0A-26
MAINTENANCE
Major Components and Service Interval
* Use only Ssangyong Genuine Parts.
Components Daily Weekly Service Interval Remarks
Engine Gasoline O - Initial change: 10,000 km More frequent maintenance is required if
the vehicle is operated under severe
oil and engine Replace at every 15,000 km condition.
oil filter O - Severe conditions?
DI diesel Initial change: 5,000 km
- Frequent low-speed operation as in
engine Replace at every 10,000 km or 12 months stop-and-go traffic
- When most trips are less than 6 km (in
IDI diesel O - winter, less than 16 km)
engine - Driving in sandy, dusty, and salty road
- Driving in mountainous areas
- Extensive idling or high load operation
such as towing a trailer
Coolant O - Replace at every 60,000 km or 3 years
Brake pipe and hose - - Initial inspection: 1,000 km
Inspect at every 20,000 km, replace if necessary
Brake pad, shoe and - - Inspect at every 10,000 km, check or adjust if necessary
disc
Air Gasoline - O Clean at every 15,000 km, If vehicle is operated under dusty or sandy
area, frequently clean and inspect the air
cleaner engine Replace at every 60,000 km cleaner system. If necessary, replace the air
element - O cleaner element.
DI diesel Initial clean: 5,000 km,
engine Clean at every 10,000 km, replace if
IDI diesel - O necessary,
engine Replace at every 30,000 km
Fuel filter Gasoline - - Replace at every 60,000 km
engine
DI diesel - - Replace at every 30,000 km (Drain the water from fuel filter at every 10,000 km)
engine
IDI diesel - - Replace at every 40,000 km
engine
Auto- 4-speed - - Inspect at every 30,000 km or 1 year, More frequent maintenance is required if the
matic replace if necessary (replace at every vehicle is operated under severe condition.
transmis- 5-speed - - - Driving in unpaved road
60,000 km if the vehicle is operated - Towing a trailer
sion oil
under severe conditions)
Manual transmission - - Inspect at every 10,000 km,
oil Replace at every 60,000 km
Transfer case oil - - Inspect at every 10,000 km,
Replace at every 60,000 km (but, frequently chexk the leaks)
Axle oil - - Replace at every 30,000 km
Air conditioner air - - Replace at every 10,000 km More frequent maintenance is required if the
vehicle is operated under severe condition.
filter - Driving in sandy, dusty, and unpaved road
- Excessive operation of air conditioner or
heater
Spark plug (gasoline - - Replace at every 60,000 km
engine)

AFFECTED VIN
DI0A-27
Lubrication Chart
Lubricant Capacity Classification
Quality API : CG grade or above,
IDI Engine 6.0 ~ 8.0 L
class** ACEA : B2, B3 or B4
Diesel
MB sheet : 229.1/3 (preferable)
DI Engine 6.8 ~ 8.3 L
Viscosity MB sheet No. 224.1
Engine oil
Quality API : SJ grade or above,
G23D 5.5 ~ 7.5 L
class** ACEA : A2 or A3
Gasoline
MB sheet : 229.1/3 (preferable)
G32D/G28D 7.0 ~ 9.0 L
Viscosity MB sheet No. 224.1
IDI Engine 10.5 ~ 11.0 L
MB sheet 325.0
Engine coolant DI Engine 11.0 ~ 12.0 L
(Antifreeze and soft water mixed) G23D 10.0 ~ 10.5 L BASF GLYSANTIN G05-11,
G32D/G28D 11.3 ~ 11.5 L HOECHST GENANTIN SUPER 8023/14
ATF DEXRON® II, III,
Manual transmission oil 4WD: 3.6 L, 2WD: 3.4 L
ATF S-2, S-3, S-4, TOTAL FLUID ATX
Brake/Clutch fluid (Level must be
maintained between MAX & MIN Properly SAE J 1703, DOT 3 or DOT 4
level)
Power steering fluid 1.1 L ATF DEXRON® II, III
4-speed: 9.5 L CASTROL TQ 95
Automatic transmission fluid
5-speed: 8.0 L SHELL or FUCHS ATF 3353
Transfer case fluid IDI Engine Part time 1.2 ~ 1.4 L
ATF DEXRON® II, III,
Part time 1.4 ~ 1.5 L
DI Engine
Full time(TOD) 1.4 ~ 1.5 L
ATF S-4, TOTAL FLUID ATX
Gasoline Full time(TOD) 1.4 ~ 1.5 L
Front 1.4 ~ 1.5 L
Axle fluid SAE 80W/90, API GL-5
Rear 2.2 L
Wheel bearing grease Properly SHELL Retinax “A” grade
Propeller shaft grease - Front/Rear Properly ALVANIA EP#2
* Please contact Ssangyong Dealer for approved alternative fluid.

** In only case not available MB 229.1 or 229.3, API or ACEA oil may be accepted, however it would rather recommend
to shorten the change interval around 30%.
IDI: Indirect Injection

DI: Direct Injection

AFFECTED VIN
DI0A-28
VEHICLE IDENTIFICATION
1. Vehicle identification Number
Vehicle identification number (VIN) is is on the right front
axle upper frame.
[KPTPOA19S1P 122357]
K .. Nation (K: Korea)
P .. Maker Identification (P: Ssangyong Motor Company)
T .. Vehicle Type (T: Passenger car - 4WD)
P .. Line Models (P: Rexton)
O . Body Type (O: 5-door)
A .. Trim Level (A: Standard, B: Deluxe,
Y220_0A018
C: Super deluxe)
1 .. Restraint System (0: No seatbelts, 1: 3-point
seatbelts, 2: 2-point seatbelt)
9 .. Engine Type (9: 3199cc, In-line 6 cylinders, Gasoline E32)
(D: 2874cc, Il-line 5 cylinders, Diesel)
S .. Check Digit (S: All area except North America)
1 .. Model Year (1: 2001, 2: 2002, 3: 2003)
P .. Plant Code (P: Pyungtaek plant)
122357 (Production serial number)
2. Certification Label
The certification label is affixed on the bottom of driver’s side
B-pillar.
Y220_0A019

AFFECTED VIN
DI0A-29
3. Engine Serial Number

The engine serial number is stamped on the lower area of
cylinder block in exhaust manifold side.
Y220_0A020
4. Manual Transmission Number

The transmission label is affixed on the upper area of clutch
housing.
5. Automatic Transmission Number

The transmisson label is affixed on the right area of transmis-
sion housing.
Y220_0A021
6. Transfer Case Number

The transfer case label is affixed on the transfer case housing.
Y220_0A022

AFFECTED VIN
DI0A-30
HOW TO USE AND MAINTAIN WORKSHOP MANUAL

CONSISTS OF WORKSHOP
MANUAL Consists of Small Group
1. Group: The manual is divided in large group like 1. Contents: In small group, included subjects and
engine, transmission, axle and others and this group detailed subjects are described in.
is also divided in small group by vehicle state. 2. General: In the general, summary of the small group
2. Small group: Each small group consists of general, (assembly), function and operational principle,
vehicle service, unit repair and special tool usage. specifications, structure and components, diagnosis
and circuit diagram are described in.
MANUAL DESCRIPTION 3. Vehicle service: Service works on the vehicle like
• The contents of the manual consist of operational replacement of parts and inspection repairs are
principle of system, specifications, diagnosis, removal/ described in the order of repair works with actual
installation on vehicle, inspections, disassembly/ photos and illustrations. Also cautions in service
assembly of removed assembly, special tool usage. works, references and inspection methods after
Not providing simple removal/installation information completion of service are described in.
but focused on to describe much more functions, roles 4. Disassembly and assembly of unit assembly:
and principles of system. Detailed service works like disassembly, inspection,
• Every automotive term like part name on the manual adjustment and assembly on removed component
is the same in parts catalog, technical bulletin and (assembly) are described in with systematic contents
drawings to avoid confusion among them. and photo illustration.
Vehicle model
Abbreviation of small
group and page
Bolded: Notice, Installation Notice,

Note
Describes information on the manual Describes small group name, model

like modification, application date, and publication date
applicable V.I.N

AFFECTED VIN
DI0A-31
GUIDELINES FOR SERVICE WORK SAFETY

General Cautions on Inspection/Service
Notice
During service works, be sure to observe below general
items for your safety.
• For service works, be sure to disconnect battery
negative (-) terminal if not starting and inspection.
• While inspecting vehicle and replacing various
consumable parts, be sure to take caution not to
damage vehicle and injure people.
• Engine and transmission may be hot enough to
burn you. So inspect related locations when they
cooled down enough.
Y220_0A024
• If engine is running, keep your clothing, tools, hair
To maintain and operate the vehicle under optimum state and hands away from moving parts.
by performing safe service works, the service works should • Even when the ignition key is turned off and
be done by following correct methods and procedures. positioned to LOCK, electrical fan can be operated
Accordingly, the purpose of this manual is to prevent dif- while working on near around electrical fan or
ferences that can be caused by personal working method, radiator grille if air conditioner or coolant
skill, ways and service procedures and to allow prompt/ temperature rises.
correct service works. • Every oil can cause skin trouble. Immediately wash
out with soap if contacted.
Note, Notice
• Painted surface of the body can be damaged if
While using this manual, there are a lot of Note or Notice
spilled over with oil or anti-freeze.
having below meaning.
• Never go under vehicle if supported only with jack.
Note • Never near the battery and fuel related system to
Note means detailed description of supplementary flames that can cause fire like cigarette.
information on work procedure or skill. • Never disconnect or connect battery terminal or other
electrical equipment if ignition key is turned on.
Notice
• While connecting the battery terminals, be cautious
Notice means precautions on tool/device or part of polarities (+, –) not to be confused.
damages or personal injuries that can occur during • There are high voltage and currency on the battery
service works. and vehicle wires. So there can be fire if short-
circuited.
However, above references and cautions cannot be inclu-
• Do not park while running the engine in an
sive measures, so should have habits of taking concerns
enclosed area like garage. There can be toxication
and cautions based on common senses.
with CO, so make sufficient ventilation.
• The electrical fan works electrically. So the fan can
be operated unexpectedly during working causing
injuries if the ignition key is not in LOCK position.
Be sure to check whether ignition key is in LOCK
position before work.
• Be careful not to touch hot components like
catalytic converter, muffler and exhaust pipe when
the engine is running or just stopped. They may
burn you badly.

AFFECTED VIN
DI0A-32
Guidelines on Engine Service Fuel and lubrication system

Painted surface of the body can be damaged or rubber
To prevent personal injuries and vehicle damages that can
products (hoes) can be corroded if engine oil and fuel are
be caused by mistakes during engine and unit inspection/
spilled over. If spilled over engine, foreign materials in air
repair and to secure optimum engine performance and
can be accumulated on the engine damaging fuel system.
safety after service works, basic cautions and service work
guidelines that can be easily forgotten during engine ser- • If work on the fluid system such as fuel and oil, working
vice works are described in. area should be well ventilated and mechanic should
not smoke.
Cautions before service works • Gasket or seal on the fuel/lubrication system should
• Before work on engine and each electrical equipment, be replaced with new and bolts and nuts should be
be sure to disconnect battery negative (-) terminal. tightened as specified.
• Before service works, be sure to prepare the works by • After removal/installation works, be sure to check
cleaning and aligning work areas. whether there is leak on the connecting section.
• Always position the ignition switch to OFF if not
required. If not, there can be electrical equipment If fine dust or foreign material enters into DI engine’s
damages or personal injuries due to short-circuit or fuel system, there can be serious damages between
ground by mistake. HP pump and injectors. So, be sure to cover removed
• There should be no leak from fuel injection system fuel system components with cap and protect removed
(HP pump, fuel hose, high pressure pipe) of the D27DT parts not to be contaminated with dirt. (Refer to clean-
engine. So they should be protected from foreign ness in this manual while working on DI engine fuel
materials. system)
• While removing the engine, do not position the jack
and others under the oil pan or engine. To secure the
safety, use only safety hook on the engine. Electrical equipment
Engine and accessories Electrical equipment should be handled more carefully.
Engine has a lot of precise portions so tightening torque Currently, the engine is equipped with a lot of electrical
should be correct during disassembly/assembly and re- equipments so there can be engine performance drops,
moval/installation and service work should be done in clean incomplete combustion and other abnormals due to short
ways during disassembly/assembly. and poor contact. Mechanics should well aware of vehicle’s
electrical equipment.
Maintaining working area clean and cautious service ad-
ministration is essential element of service works while • If have to work on the electrical equipment, be sure to
working on the engine and each section of the vehicle. So disconnect battery negative (-) terminal and position
the mechanics should well aware of it. the ignition switch to off if not required.
• While removing the engine, related parts (bolts, • When replacing electrical equipment, use the same
gaskets, etc.) should be aligned as a group. genuine part and be sure to check whether ground or
connecting portions are correctly connected during
• While disassembling/assembling internal components
installation. If ground or connecting portion is loosened,
of the engine, well aware of disassembly/assembly
there can be vehicle fire or personal injury.
section in this manual and clean each component with
engine oil and then coat with oil before installation.
• While removing engine, drain engine oil, coolant and
fuel in fuel system to prevent leakage.
• During service work of removal/installation, be sure to
check each connected portions to engine not to make
interference.

AFFECTED VIN
DI0A-33
During Service Work - Inspection

1. Before lifting up the vehicle with lift, correctly support the
lifting points and lift up.
2. When using a jack, park the vehicle on the level ground
and block front and rear wheels. Position the jack under
the frame and lift up the vehicle and then support with
chassis stand before service work.
Y220_0A025
3. Before service work, be sure to disconnect battery

negative (-) terminal to prevent damages by bad wire and
short.
Y220_0A026
4. If service from interior of the vehicle, use protection cover

to prevent damage and contamination of seat and floor.
5. Brake fluid and anti-freeze can damage painted surface
of body. So carefully handle them during service work.
Y220_0A027
6. Use recommended and specified tools to increase

efficiency of service work.
7. Use only genuine spare parts.
Y220_0A028

AFFECTED VIN
DI0A-34
8. Never reuse cotter pin, gasket, O-ring, oil seal, lock

washer and self-locking nut. Replace them with new.
If reused, normal functions cannot be maintained.
9. Align the disassembled parts in clean according to
disassembling order and group for easy assembling.
10. According to installing positions, the bolts and nuts have
different hardness and design. So be careful not to mix
removed bolts and nuts each other and align them
according installing positions.
11. To inspect and assemble, clean the parts.
12. Securely clean the parts that related with oil not to be
Y220_0A029 affected by viscosity of oil.
13. Coat oil or grease on the driving and sliding surfaces
before installing parts.
14. Use sealer or gasket to prevent leakage if necessary.
15. Damaged or not, never reuse removed gasket. Replace
with new and cautious on installing directions.
16. Tighten every bolt and nut with specified torque.
17. When service work is completed, check finally whether
the work is performed properly or the problem is solved.
18. If work on the fuel line between priming pump and injector
(including return line), be sure to cover the removed parts
with cap and be careful not to expose the connecting
Y220_0A030
passage and removed parts to external foreign materials
or dust. (Refer to cleanness.)
19. If remove high pressure fuel supply pipe between HP pump
and fuel rail and high pressure fuel pipe between fuel rail
and each injector, be sure to replace them with new.

AFFECTED VIN
DI0A-35
During Service Work for Electric

Devices
Notice
Be careful not to modify or alter electrical system and

electrical device. Or there can be vehicle fire or serious
damage.
1. Be sure to disconnect battery negative (-) terminal during

every service work. Before disconnecting battery negative
(-) terminal, turn off ignition key. Y220_0A031
2. Replace with specified capacity of fuse if there is bad,

blown or short circuited fuse. If use electrical wire or steel
wire other than fuse, there can be damages on the various
electrical systems. If replaced with over-capacity fuse,
there can be damages on the related electrical device
and fire.
3. Every wire on the vehicle should be fastened securely
not to be loosened with fixing clip.
4. If wires go through edges, protect them with tape or other
materials not to be damaged.
5. Carefully install the wires not to be damaged during

installation/removal of parts due to interference.
6. Be careful not to throw or drop each sensor or relay.
7. Securely connect each connector until hear a “click”
sound.
Y220_0A032

AFFECTED VIN
DI0A-36
LIFTING POINTS
Lifting Positions
1. 4-post lift
As illustrated, position the vehicle on the 4-post lift securely and block the front and rear of each tire not to move during
working.
Notice
During lifting, be sure to check whether vehicle is empty.

• Board-on lift connection device installed in front of vehicle should be positioned in front of sill locating
under the front door.
• Install lift connecting device on the edge of front and rear of board-on lift.
Warning
• Be sure to use attachment during lifting to prevent the lift from contacting with body floor.
• While lifting the vehicle, widen the lift floor as far as possible to stabilize between vehicle front and rear. When
fixing the lift floor, be careful not to contact with brake tube and fuel lines.
2. Safety jack and safety stand

If lift up the vehicle with safety jack and stand, should be more
careful during works.
Warning
• Never be under the vehicle if supported with only jack.
If have to be under the vehicle, be sure to use safety
block.
• Use wheel block in front and rear of every wheel.
Y220_0A033

AFFECTED VIN
DI0A-37
TIGHTENING TORQUE OF STANDARD BOLTS

Tightening Torque By Bolt Specification
Tightening Torque (kg.cm)
Bolt
Pitch Standard Tightening Torque Max. Allowable Tightening Torque
Diameter
4T 7T 9T 4T 7T 9T
M3 0.5 5 9 13 7 12 17
M4 0.7 12 20 30 16 27 40
M5 0.8 24 40 57 32 53 77
M6 1.0 41 68 99 55 91 130
M8 1.25 88 160 230 130 210 310
M10 1.25 190 330 470 260 430 620
1.5 190 310 450 250 420 600
M12 1.25 350 580 840 460 770 1,100
1.75 330 550 790 440 730 1,000
M14 1.5 550 910 1,300 730 1,200 1,900
M16 1.5 830 1,100 2,000 1,100 1,900 2,700
M18 1.5 1,200 2,000 2,900 1,600 2,700 3,800
M20 1.5 1,700 2,800 4,000 2,200 3,700 5,300
M22 1.5 2,300 3,800 5,400 3,000 5,000 7,200
M24 1.5 2,900 4,900 7,000 3,900 6,500 9,400
2.0 2,800 4,700 6,800 3,800 6,300 9,100
Y220_0A034
1. Metric bolt strength is embossed on the head of each 3. Determine extra proper tightening torque if tightens
bolt. The strength of bolt can be classified as 4T, 7T, with washer or packing.
8.8T, 10.9T, 11T and 12.9T in general. 4. If tightens bolts on the below materials, be sure to
2. Observe standard tightening torque during bolt determine the proper torque.
tightening works and can adjust torque to be proper • Aluminum alloy: Tighten to 80 % of above torque
within 15 % if necessary. Try not to over max. table.
allowable tightening torque if not required to do so.
• Plastics: Tighten to 20 % of above torque table.

AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SECTION DI01
ENGINE ASSEMBLY
DI01-1
SECTION
00 DI01
ENGINE ASSEMBLY
Table of Contents
STRUCTURE AND FUNCTION DESCRIPTIONS ........ DI01-3

D27DT engine ........................................................ DI01-3
Engine performance curve ..................................... DI01-8
General diagnosis ................................................. DI01-10
DIAGNOSTIC INFORMATION AND PROCEDURE .. DI01-15
Oil leak diagnosis .................................................. DI01-15
Compression pressure test .................................. DI01-16
Cylinder pressure leakage test ............................ DI01-18
Tightening torque .................................................. DI01-19
REMOVAL AND INSTALLATION .............................. DI01-22
Engine mounting ................................................... DI01-22
DISASSEMBLY AND REASSEMBLY ........................ DI01-32
Components and special tools ............................. DI01-32
ENGINE ASSEMBLY CHANGED BY

AFFECTED VIN
DI01-3
STRUCTURE AND FUNCTION DESCRIPTIONS

D27DT ENGINE
Major Components in Engine and Engine Compartment
The advanced electronically controlled D27DT engine that has high pressure fuel system has been introduced to this
vehicle. It satisfies the strict emission regulation and provides improved output and maximum torque.
Y220_01001
1. Coolant reservoir 6. Fuse box 11. EGR valve

2. FFH device 7. Battery 12. Air cleaner assembly
3. Brake fluid reservoir 8. Fuel filter 13. Turbo charger
4. Washer fluid reservoir 9. Power steering pump 14. Oil dipstick
5. Common rail 10. Priming pump

AFFECTED VIN
DI01-4
Engine Structure
Front View
Rear View
Y220_01002
1. TVD (Torsional Vibration Damper) 7. Viscos fan clutch 13. Oil filter
2. Air conditioner compressor 8. Auto tensioner pulley 14. Vacuum pump
3. Power steering pump pulley 9. Auto tensioner 15. Crank position sensor
4. Idle pulley 10. Poly-grooved belt 16. EGR valve
5. Coolant pump pulley 11. Cam position sensor 17. Power steering pump
6. Alternator 12. Drive plate (MT: DMF) 18. EGR to center pipe
CHANGED BY ENGINE ASSEMBLY

AFFECTED VIN
DI01-5
Top View
Y220_01003
19. Cylinder head cover 24. Fuel pipe 29. Booster pressure sensor
20. Intake manifold 25. Injector 30. PCV valve and oil separator
21. Water outlet port 26. Fuel return line 31. Oil dipstick
22. Common rail 27. Oil filler cap 32. EGR-LH pipe
23. Fuel pressure sensor 28. Glow plug

AFFECTED VIN
DI01-6
Left Side View
Right Side View
Y220_01004
33. Cylinder head 38. EGR-RH pipe 42. Turbo charger booster vacuum
34. Cylinder block 39. PCV valve and oil separator modulator
35. Oil pan 40. Oil dipstick 43. EGR valve vacuum modulator
36. Drain plug 41. High pressure pump 44. EGR valve
37. Turbo charger 45. Exhaust manifold

AFFECTED VIN
DI01-7
Specifications
Description Specification
Engine Type/Number of cylinders D27DT/5-cylinder
Cylinder Inner diameter (mm) 86.2
Stroke (mm) 92.4
Displacement (cc) 2696
Compression ratio 18:1
Maximum output (ps/rpm) 170/4,000
Maximum torque (kg.m/rpm) 34.7/1,800
Idle speed For Manual Transmission 750 ± 50 rpm

For Automatic Transmission 750 ± 50 rpm
Valve Intake Opens (BTDC) 16°
Closes (ABDC) 33°
Exhaust Opens (BBDC) 46°
Closes (ATDC) 21°
Camshaft Type DOHC

Fuel system Fuel type Low sulfur diesel
Fuel pump type Vane pump in HP pump
Fuel supply pressure HP pump inlet port: max. 400 mbar
HP pump outlet port (with IMV fully open):
over 1,050 bar
Water separation in fuel filter at every 10,000 km
Fuel tank capacity ( ) 80
Lubrication system Oil specification SAE 10W40, 5W40
(MB Sheet 229.1, 229.3 approved oil)
Lubrication type Forced delivery
Oil filter type Full flow, filter element type
Oil capacity ( ) 6.8 ~ 8.3
Cooling system Cooling type Water cooling type
Cooling fan operation type Belt operated typr
Thermostat: Fully Opening 85
Open: 100°C) temperature (°C)
Type WAX pellet type
Coolant capacity ( ) 11.5

AFFECTED VIN
DI01-8
ENGINE PERFORMANCE CURVE

Output and Torque
Output [PS]
Torque [Nm]
Speed [rpm]
Y220_00025

AFFECTED VIN
DI01-9
Oil Temperature/Pressure and Boost Pressure
Oil pressure [bar]
Oil temperature [C]

Boost pressure [bar]
Speed [rpm]
Y220_00026

AFFECTED VIN
DI01-10
GENERAL DIAGNOSIS
Condition Probable Cause Correction
Hard Starting Malfunction of • Faulty fuse. • Replace the fuse.
(With normal Ignition System
cranking) • Faulty spark plug. • Clean, adjust the plug gap or
replace.
• Electric leakage at the high • Replace the cable.
tension cable.
• Poor connection of the high • Replace the cable or wires.
tension cable or lead wires.
• Improper ignition timing. • Adjust the ignition timing.
• Faulty ignition coil. • Replace the ignition coil.
Malfunction of • Lock of fuel in the fuel tank. • Feed the fuel.
Fuel System
• Dirty or clogged fuel filter. • Replace the filter.
• Clogged fuel pipe. • Clean the fuel pipe.
• Malfunction of the fuel pump. • Replace the fuel pump.
• Malfunction of the fuel injector. • Replace the injector.
• The foreign material in the fuel • Clean the fuel tank.
tank.
Decline of • Poor tightening spark plug. • Tighten to the specified torque.
Compression Compression
Pressure
• Cracked cylinder head gasket. • Replace the gasket.
• Inadequate the valve clearance. • Adjust the clearance.
• Leakage of the valve clearance. • Repair the valve.
• Interference of the valve stem. • Replace the valve or the valve
guide.
• Low elasticity or damage of the • Replace the valve spring.
valve spring.
• Abnormal interference of pistons • Replace the piston ring.
and cylinders.
• Excessive wear of pistons, • Replace the ring or the piston
rings, or cylinders. and boring or replace the
cylinder.
Others • Broken timing belt. • Replace the belt.
• Loosening, damage or leakage • Connect the hose correctly or
of the vacuum hose. replace it.
• Leakage of intake system. • Replace intake system.
Lack of Engine Decline of • Refer to above in this page. • Refer to above in this page.
Power Compression
Pressure
Malfunction of • Improper ignition timing. • Adjust the ignition timing.
Ignition System
• Faulty spark plug. • Adjust or replace the spark plug.
• Electric leakage or poor • Connect the cable correctly or

connection of the high tension replace it.
cable.

AFFECTED VIN
DI01-11
GENERAL DIAGNOSIS (Cont’d)

Lack of Engine Malfunction of • Clogged fuel pipe. • Clean the pipe.
Power Fuel System
• Clogged or contaminated fuel • Replace the filter.
filter.
Others • Clogged exhaust system. • Check and repair the system.
• Clogged or contaminated air • Clean or replace the air cleaner
cleaner element. element.
• Leak of the intake manifold • Replace the gasket.
gasket.
• Dragging brakes. • Repair or replace the brakes.
Rough Engine Decline of • Refer to “Compression Pressure • Refer to “Compression Pressure
Idling Compression Test”. Test”.
Pressure
Malfunction of • Clogged fuel pipe. • Clean the pipe.
Fuel System
• Clogged or contaminated fuel • Replace the filter.
filter.
• Malfunction of the fuel pressure • Replace the regulator.
regulator.
Malfunction of • Malfunction of the spark plug. • Adjust or replace the spark plug.
Ignition System
• Electric leakage or poor connec- • Connect the cable correctly or
tion of the high tension cable. replace it.
• Poor ignition timing. • Adjust the ignition timing.

• Malfunction of the ignition coil. • Replace the ignition coil.
Others • Clogged or contaminated air • Clean or replace the air cleaner
cleaner element. element.
gasket.
• Poor connection or damage or • Connect the hose correctly or
leakage of the vacuum hose. replace it.
Engine Hesitate Decline of • Refer to “Compression Pressure • Refer to “Compression Pressure
(Upon pressing Compression Test”. Test”.
accelerating Pressure
pedal, the
engine makes
Malfunction of • Poor ignition timing. • Adjust the ignition timing.
Ignition System
delayed re- • Poor spark plug or Poor adjust- • Replace the plug or adjust the
sponse This ment of the plug gap. gap.
situation is • Electric leakage or poor connec- • Connect the cable correctly or
remarkable tion of the high tension cable. replace it.
when cruising or
starting.) Others • Malfunction of the air cleaner • Clean or replace the air cleaner
system. system.
gasket.

AFFECTED VIN
DI01-12

Engine Surging Decline of • Refer to “Compression Pressure • Refer to “Compression Pressure
(Engine power Compression Test”. Test”.
makes Pressure
fluctuation in a Malfunction of
fixed speed and • Clogged fuel pipe. • Clean the pipe.
Fuel System
speed changes • Clogged or contaminated fuel • Replace the filter.
without filter.
operating the • Malfunction of the fuel pressure • Replace the fuel pressure
accelerating regulator. regulator.
pedal.)
Malfunction of • Malfunction of the spark plug. • Adjust or replace the spark plug.
Ignition System
• Electric leakage or poor • Connect the cable correctly or
cable.
• Poor ignition timing. • Adjust the ignition timing.
Others • Leak of the intake manifold • Clean or replace the gasket.
gasket.
• Leakage of the vacuum hose. • Connect the hose correctly or
replace it.
Excessive Overtheated • Refer to “Overheat” in this page. • Refer to “Overheat” in this page.
Detonation Engine
(According to
the opening
Malfunction of • Abnormal spark plug. • Replace the spark plug.
Fuel System
range of Mal- • Poor ignition timing. • Adjust the ignition timing
function of • Electric leakage or poor • Connect the cable correctly or
metallic is connection of the high tension replace it.
made with cable.
abnormal Malfunction of
explosion )
• Clogged or contaminated fuel • Clean or replace the fuel filter
Ignition System filter and fuel pipe. and the fuel pipe.
Others • Leak of the intake manifold • Replace the gasket.
gasket.
• Excessive carbon deposit due to • Remove the carbon.
abnormal combustion.
Overheat Malfunction of • Lack of coolant. • Refill coolant.
Cooling System
• Malfunction of the thermostat. • Replace the thermostat.
• Malfunction of the cooling fan. • Check or replace the cooling
fan.
• Poor water pump performance. • Replace the pump.
• Clogged or leaky radiator. • Clean, repair or replace the
radiator.
Malfunction of • Poor engine oil. • Replace engine oil with the
Lubrication specified one.
System
• Blocking oil filter or strainer. • Clean or repair the oil filter or the
strainer.
• Lack of engine oil. • Refill oil.
• Poor oil pump performance. • Replace or repair the pump.
Other • Leakage of oil • Repair.
• Damaged cylinder head gasket. • Replace the gasket.

AFFECTED VIN
DI01-13

Poor Fuel Decline of • Refer to “Compression Pressure • Refer to “Compression Pressure
Consumption Compression Test”. Test”.
Pressure
Malfunction of • Leakage of the fuel tank or the • Repair or replace the fuel tank or
Fuel System fuel pipe. the fuel pipe
Malfunction of • Improper ignition timing. • Adjust the ignition timing.
Ignition System
• Abnormal spark plug • Replace the plug.
(Excessive carbon deposit,
inadequate gap, burnt electrode).
• Electric leakage or poor • Connect the cable normally or
cable.
Malfunction of • Malfunction of the thermostat. • Repair the thermostat.
Cooling System
Others • Improperly installed valve. • Repair or replace the valve.
• Low pressure of tires. • Adjust the pressure of tires.
Excessive Leakage of • Loosened oil drain plug. • Tighten the plug.
Consumption of Engine Oil
Engine Oil
• Loosened oil pan bolt. • Tighten the bolt. Engine Oil
• Loosened oil filter. • Tighten the filter.
• Loosened oil pressure switch. • Tighten the switch.
• Leakage of camshaft front oil • Replace the seal.
seal.
• Leakage of crankshaft front oil • Replace the seal.
seal.
• Leakage at the cylinder head • Replace the gasket.
cover gasket.
• Damage of the cylinder head • Replace the gasket.
gasket.
Oil Mixing in • Stuck piston ring. • Remove carbon and replace the
Combustion ring.
Chamber
• Worn piston or cylinder. • Replace the piston or the
cylinder.
• Worn piston ring or ring groove. • Replace the piston or ring.
• Inadequate position of the piston • Adjust the position.
ring cutting part.
• Abrasion or damage of the valve • Replace the valve system.
system.
Low Oil Malfunction of • Inadequate oil viscosity. • Replace with the specified one.
Pressure Lubrication
System
• Loosening of the oil pressure • Tighten the switch.
switch.
• Lack of engine oil. • Refill oil.
• Blocking oil strainer. • Clean the strainer.
• Lowered function of the oil • Replace the pump.
pump.
• Abrasion or damage of the oil • Replace the valve.
pump relief valve.

AFFECTED VIN
DI01-14

Engine Noise Valve Noise • Inadequate valve clearance • Adjust the valve clearance.
• Abrasion of valve stem or guide. • Replace the valve stem or the
guide.
• Weak valve spring. • Replace the spring.
Piston, Ring, • Abrasion of the piston, the ring • Boring the cylinder or replace
Cylinder Noise or the cylinder. the piston, the ring or the
cylinder.
Connecting Rod • Abrasion of the connecting rod • Replace the bearing.
Noise bearing.
• Loosened the connecting rod • Tighten to the specified torque
nut.
Crankshaft • Abrasion of the crankshaft • Replace the bearing.
Noise bearing.
• Abrasion of the crankshaft • Grind or replace the crankshaft
journal. journal.
• Loosened bearing cap bolt. • Tighten to the specified torque.
• Excessive clearance of the • Adjust or replace.
crankshaft thrust bearing.
• Low oil pressure. • Refer to “Low Oil Pressure” in
this section.

AFFECTED VIN
DI01-15
DIAGNOSTIC INFORMATION AND PROCEDURE

OIL LEAK DIAGNOSIS Black Light and Dye Method
Most fluid oil leaks are easily located and repaired by vi- A dye and light kit is available for finding leaks, Refer to
sually finding the leak and replacing or repairing the nec- the manufacturer's directions when using the kit.
essary parts. On some occasions a fluid leak may be dif- 1. Pour the specified amount of dye into the engine oil
ficult to locate or repair. The following procedures may fill tube.
help you in locating and repairing most leaks.
2. Operate the vehicle normal operating conditions as
directed in the kit.
Finding the Leak 3. Direct the light toward the suspected area. The dyed
1. Identify the fluid. Determine whether it is engine oil, fluid will appear as a yellow path leading to the
automatic transmission fluid, power steering fluid, etc. source.
2. Identify where the fluid is leaking from.
2.1 After running the vehicle at normal operating Repairing the Leak
temperature, park the vehicle over a large sheet Once the origin of the leak has been pinpointed and traced
of paper. back to its source, the cause of the leak must be deter-
2.2 Wait a few minutes. mined in order for it to be repaired properly. If a gasket is
2.3 You should be able to find the approximate replaced, but the sealing flange is bent, the new gasket
location of the leak by the drippings on the will not repair the leak. The bent flange must be repaired
paper. also. Before attempting to repair a leak, check for the fol-
lowing conditions and correct them as they may cause a
3. Visually check around the suspected component.
leak.
Check around all the gasket mating surfaces for
leaks. A mirror is useful for finding leaks in areas that
are hard to reach. Gaskets
4. If the leak still cannot be found, it may be necessary • The fluid level/pressure is too high.
to clean the suspected area with a degreaser, steam
• The crankcase ventilation system is malfunctioning.
or spray solvent.
• The fasteners are tightened improperly or the threads
4.1 Clean the area well.
are dirty or damaged.
4.2 Dry the area.
• The flanges or the sealing surface is warped.
4.3 Operate the vehicle for several miles at normal
• There are scratches, burrs or other damage to the
operating temperature and varying speeds.
sealing surface.
4.4 After operating the vehicle, visually check the
• The gasket is damaged or worn.
suspected component.
• There is cracking or porosity of the component.
4.5 If you still cannot locate the leak, try using the
powder or black light and dye method. • An improper seal was used (where applicable).
Seals
Powder Method • The fluid level/pressure is too high.
1. Clean the suspected area. • The crankcase ventilation system is malfunctioning.
2. Apply an aerosol-type powder (such as foot powder) • The seal bore is damaged (scratched, burred or nicked).
to the suspected area. • The seal is damaged or worn.
3. Operate the vehicle under normal operating • Improper installation is evident.
conditoins.
• There are cracks in the components.
4. Visually inspect the suspected component. You
• The shaft surface is scratched, nicked or damaged.
should be able to trace the leak path over the white
powder surface to the source. • A loose or worn bearing is causing excess seal wear.

AFFECTED VIN
DI01-16
COMPRESSION PRESSURE TEST

The compression pressure test is to check the conditions of internal components (piston, piston ring, intake and
exhaust vale, cylinder head gasket). This test provides current engine operating status.
Notice
• Before cranking the engine, make sure that the test wiring, tools and persons are keeping away from moving
components of engine (e.g., belt and cooling fan).
• Park the vehicle on the level ground and apply the parking brake.
• Do not allow anybody to be in front of the vehicle.
Y220_01005
Specifications
Compression ratio 18 : 1
Test temperature at normal operating temperature (80°C)
Compression pressure Normal value 32 bar
Minimum value 18 bar
Permissible pressure difference between individual cylinders Max. 3 bar

AFFECTED VIN
DI01-17
Measuring Procedure
Notice
• Disconnect the fuel rail pressure sensor connector to cut off the fuel injection.
• Discharge the combustion residues in the cylinders before testing the compression pressure.
• Apply the parking brake before cranking the engine.
1. Warm the engine up to normal operating temperature

(80°C).
2. Disconnect the fuel rail pressure sensor connector to
cut off the fuel injection.
3. Place the diagram sheet to compression pressure tester.
Y220_01006
4. Remove the glow plugs and install the compression

pressure tester into the plug hole.
Tightening torque (Tester) 15 Nm
Y220_01007
5. Crank the engine for approx. 10 seconds by using the

start motor.
6. Record the test result and measure the compression
pressure of other cylinders with same manner.
7. If the measured value is not within the specifications,
perform the cylinder pressure leakage test.
Y220_01008

AFFECTED VIN
DI01-18
CYLINDER PRESSURE LEAKAGE TEST

If the measured value of the compression pressure test is not
within the specifications, perform the cylinder pressure leak-
age test.
Y220_01009
Permissible Pressure Leakage

Test temperature at normal operating temperature (80°C)
At whole engine Max. 25 %
At valve and cylinder head gasket Max. 10 %
At piston ring Max. 20 %
Notice
• Perform the pressure in order: 1 - 2 - 3 - 4 - 5

• Do not test the cylinder pressure leakage with wet type test procedure. (do not inject the engine oil into the
combustion chamber)

AFFECTED VIN
DI01-19
TIGHTENING TORQUE
NO. Name Size Quantity Tightening Torque
1 Oil nozzle M6 x 22 5 10 ± 1
55 ± 5
2 Main bearing cap M11 x 62 12
90° ± 10°
40 ± 5
3 Connecting rod cap M9 x 52 5
90° ± 10°
4 Rear cover M6 x 20 6 10 ± 1
5 Oil pump M8 x 35SOC 3 25 ± 2.5
6 Oil baffle plate assembly M6 x 20 10 10 ± 1
M6 x 16 1 10 ± 1
M6 x 40 6 10 ± 1
7 T.G.C.C M6 x 60 3 10 ± 1
M6 x 70 2 10 ± 1
M8 x 80SOC 1 25 ± 2.5
45 ± 5
8 Flywheel M10 x 30 8
90° ± 10°
325 ± 33
9 Crankshaft hub M18 x 50 1
90° ± 10°
M6 x 20 24 10 ± 1
M6 x 35 3 10 ± 1
10 Oil pan
M6 x 38 3 10 ± 1
M6 x 40 4 25 ± 2.5
11 High pressure pump assembly M8 x 40 4 25 ± 2.5
12 High pressure pump sprocket assembly M14 x 1.5-8-1 1 65 ± 5
13 High pressure pump bracket M7 x 16 3 20 ± 2 x 90° + 10°
M8 x 25 2
25 ± 2.5
M8 x 50 2
14 Cylinder head assembly Step1: 20 Nm ± 2 Nm
M12 x 177 11
Step2: 85 Nm ± 5 Nm
M12 x 158 1 Step3: 3 x 90° + 10°
15 Camshaft cap M8 x 60 24 25 ± 2.5
16 Stud bolt M8 10 15 ± 1.5
Camshaft sprocket (Intake) 1 25 ± 2.5
17 M11 x 52
Camshaft sprocket (Exhaust) 1 90° ± 10°
18 Chain tensioner M22 1 65 ± 5
19 Coolant temperature sensor M14 1 22 ± 2.2

AFFECTED VIN
DI01-20

M8 x 45(LOWER) 1 32 ± 3
20 Auto tensioner
M12 x 90 1 82 ± 6
21 Water pump assembly M6 x 50 7 10 ± 1
22 Water pump pulley M6 x 12 4 10 ± 1
23 Hot water inlet pipe assembly M6 x 12 2 10 ± 1
24 Alternator bracket M8 x 32 4 25 ± 2.5
25 Alternator M10 x 90 2 46 ± 4.6
26 Air conditioner compressor assembly M8 x 95 4 46 ± 4.6
Air conditioner compressor bracket M8 x 25 1 25 ± 2.5
27
assembly M8 x 60 3 25 ± 2.5
Air conditioner compressor sub M6 x 14 1 10 ± 1.0
28
bracket assembly M8 x 16 1 25 ± 2.5
M8 x 45 6 25 ± 2.5
29 Intake manifold
M8 x 130 6 25 ± 2.5
30 Bracket M6 x 16 1 10 ± 1.0
31 Knock sensor M8 x 28 2 20 ± 2.6
32 Camshaft position sensor M8 x 16 1 12 ± 1.7
33 Booster pressure sensor M6 x 16 2 10 ± 1.0
34 Exhauster manifold M8 10 40 ± 4
35 Turbo charger assembly M8 4 25 ± 2.5
36 Turbo charger adaptor piece 1 32 ± 3.2
37 Nut M8 1 25 ± 2.5
38 Combination bolt M8 x 22 1 25 ± 2.5
M6 x 16 (Cylinder block side) 1 25 ± 2.5
39 T/C oil supply pipe
M16 (T/C side) 1 20 ± 2.0
M6 x 16 (T/C side) 2 10 ± 1.0
40 T/C oil return pipe
M6 x 16 (Cylinder block side) 2 10 ± 1.0
41 EGR valve assembly M8 x 22 2 25 ± 2.5
M6 x 16 2 10 ± 1.0
42 EGR-LH pipe bolt
M8 x 22 2 35 ± 2.0
M6 x 16 4 10 ± 1.0
EGR combination bolt
43 M8 x 16 4 25 ± 2.5
EGR-RH pipe nut M8 2 35 ± 2.0
44 Glow plug cable nut M5 5 15 ± 3
45 Vacuum pump M6 x 20 3 10 ± 1.0
M6 x 25 5 10 ± 1.0
46 Cooling fan bracket assembly M6 x 65 1 10 ± 1.0
M6 x 85 3 10 ± 1.0
47 Cylinder head cover M6 x 35 21 23 ± 2.3

AFFECTED VIN
DI01-21

48 Vacuum modulator M6 x 16SOC 4 10 ± 1.0
49 WDT combination bolt M6 x 16 3 10 ± 1.0
50 Oil dipstick tube M6 x 16 1 10 ± 1.0
M8 x 35SOC 1 25 ± 2.5
51 Oil filter assembly M8 x 50SOC 2 25 ± 2.5
M8 x 55SOC 1 25 ± 2.5
52 Fuel rail assembly M8 x 35SOC 3 25 ± 2.5
10 ± 1.0
53 Injector clamp washer M6 x 60 5
180 + 20°
54 Fuel pipe clip (H-C) M6 x 19 1 10 ± 1.0
55 Fuel pipe clip (C-I) M6 x 16 5 10 ± 1.0
56 Crankshaft position sensor M5 x 17 1 0.8 ± 0.4
57 Crankshaft position sensor GAP 0.7 ~ 1.5
58 Fuel pressure sensor 1
59 Wiring M6 x 16 5 10 ± 1.0
M8 x 16 2 25 ± 2.5
60 Intake manifold bracket
M8 x 40 2 25 ± 2.5
M8 x 100 2 25 ± 2.5
61 Power steering pump
NUT 2 25 ± 2.5
62 Piston protrusion 5 0.765 ~ 1.055
Clearance between connecting rod
63 5 0.05 ~ 0.31
and pin boss
64 End play of crankshaft NEW: 0.100 ~ 0.245 mm // USED: 0.300 mm

AFFECTED VIN
DI01-22
REMOVAL AND INSTALLATION

ENGINE MOUNTING
1. Side Mountings
Left
Right
2. Transmission Mounting
3. Exhaust Manifold and Pipe 4. Cables and Connectors
Y220_01010
Notice
1. Disconnect the negative battery cable before removal.

2. Drain the engine oil.
3. Drain the engine coolant.
4. Be careful not to splash the fuel to the vehicle body. It may cause a fire or vulcanization of rubber products.
Make sure to block the fuel related hoses before removal.

AFFECTED VIN
DI01-23
Engine Assembly - Removal

1. Disconnect the negative battery cable.
Notice
If not necessary, place the ignition switch at “OFF”
position.
Y220_01011
2. Remove the engine hood assembly.
Note
Refer to “Body” section.
Y220_01012
3. Remove the skid plate under the engine compartment.

Installaiton Notice
Tightening torque 12 ± 1.2 Nm
Y220_01013
4. Loosen the radiator drain cock and drain the coolant.
Notice
1. Be careful not to contact with coolant. If contacted,

wash with soap and water to ensure all coolant is
removed.
2. Use only designated coolant.
3. Open the coolant reservoir cap to help the
draining.
Y220_01014

AFFECTED VIN
DI01-24
5. Loosen the cylinder block drain plug (under the intake

manifold) and drain the coolant completely.
6. Retighten the drain plug with the specified tightening
torque.
Tightening torque 30 Nm
Y220_01015
7. Remove the inlet hose (1) and the heater hose (2) under
the radiator.
Notice
Be careful not to damage the rubber hose.
Y220_01016
8. Remove the coolant outlet hose over the radiator.
Notice
Be careful not to damage the rubber hose.
Y220_01017
9. Remove the radiator grille and loosen the hose clamp on

the outlet port of turbo intercooler.
Note
For the removal and installation of radiator grille,
refer to “Cooling System” section.
Y220_01021

AFFECTED VIN
DI01-25
10. Loosen the hose clamp on intake air hose of turbo charger
and remove the intake air hose.
Y220_01022
11. Separate the outlet hose of oil separator from the intake
air hose of turbo charger.
12. Loosen the clamp on the intake air duct hose of turbo
charger at the air cleaner side and separate the hose
from the air cleaner housing.
Y220_01018
13. Loosen the clamps and remove the intake air hose from
the turbo charger.
Y220_01020
14. Loosen the clamp on the inlet hose of intercooler.
Y220_01023

AFFECTED VIN
DI01-26
15. Loosen the clamp on the intake manifold and remove the
intake air hose.
Y220_01024
16. Remove the exhaust pipe mounting nuts from the turbo
charger.
Installation Notice
Y220_01027
17. Remove the power steering inlet pipe and the outlet hose
from the power steering pump.
Notice
Plug the openings of hoses and pump with caps not
to flow out the oil.
Installation Notice
Inlet pipe union nut 25 ± 2.5 Nm
Y220_01028
18. Remove the vacuum hose from the brake booster.

Installation Notice
Vacuum pipe union nut

10 Nm
(at vacuum pump side)
Y220_01029

AFFECTED VIN
DI01-27
19. Remove the supply inlet, supply outlet and return hose
from the fuel filter.
Notice
1. When separating the hoses from the fuel filter,

plug the openings with caps so that the
contaminants will not get into the fuel system.
2. Mark on all the hoses not to be mixed each other.
Y220_01030
20. Remove the engine oil heater outlet hose.

21. Disconnect the cables from the cylinder block and other
components.
(e.g., coolant temperature sensor cable and oil
temperature switch)
Y220_01031
22. Disconnect the engine ground cable and the alternator

“+” terminal cable.
Notice
Make sure to properly tighten the cable nuts when

installing. Otherwise, it may cause a poor ground or
electric charging problem.
Y220_01032
23. Disconnect the “ST” terminal and “+” terminal cables from
the starter motor.
Notice
Make sure to properly tighten the cable nuts when

installing. Otherwise, it may cause an engine starting
problem.
Y220_01033

AFFECTED VIN
DI01-28
24. Disconnect the air conditioner compressor connector and

remove the inlet and outlet pipes from the compressor.
Y220_01034
25. For the automatic transmission equipped vehicle, remove

the oil cooler pipes.
Y220_01035
Note
The oil cooler pipes are connected to cylinder block
at both sides and bottom area of oil with brackets.
Installation Notice
Pipe mounting bracket bolt 25 ± 2.5 Nm

Pipe hose (radiator side)
25 ± 2.5 Nm
union nut
Y220_01036
26. Set up the special to the cooling fan pulley and remove
the cooling fan assembly. To make the removal easier,
loosen the radiator shroud.
Installation Notice
Cooling fan pulley bolt 10 ± 1.0 Nm
Y220_01038

AFFECTED VIN
DI01-29
27. Remove the radiator shroud.
Installation Notice
Y220_01039
28. Take off the fan belt from the engine.
Note
1. Insert a tool into the belt tensioner and rotate it
counterclockwise to take off the fan belt.
2. After installation of the fan belt, pump the belt
tensioner 3 to 4 times.
Y220_01040

AFFECTED VIN
DI01-30
29. Remove the transmission mounting bolts and separate the engine assembly from the transmission assembly.
Y220_01041
Note
1. Before unscrewing the transmission mounting
bolts, remove the starter motor.
Installation Notice
Mounting bolt 55 ± 5 Nm

AFFECTED VIN
DI01-31
30. Remove the engine assembly mounting nuts at both sides.

Installation Notice
Mounting Nut 55 ± 5 Nm
Y220_01042
31. Hook the chain on the engine brackets and carefully 32. Put the removed engine assembly on the safety stand.
pull out the engine assembly from the vehicle by using
a hoist or crane.
Y220_01043

AFFECTED VIN
DI01-32
DISASSEMBLY AND REASSEMBLY
COMPONENTS AND SPECIAL TOOLS

Injector puller Glow plug puller Fuel pipe wrench Sealing caps
Injector copper washer

puller
Engine lock
Valve remover/installer Pulley lock/wrench HP pump lock HP pump bearing puller
Y220_01044

AFFECTED VIN
DI01-33
Inspection Before Disassembly and

Reassembly
Preparations and Preceding Works
1. Remove the cylinder block drain plug and seal and
completely drain the residual coolant from the cylinder
block.
Notice
Y220_01045
Replace the seal with new one once removed.
2. When the fan belt is installed, gently pump the belt shock
absorber mounting bolt (M19) 3 times.
3. Take off the fan belt while pushing the mounting bolt (M19).
Y220_01046
4. Loosen the oil drain plug and completely drain the engine
oil.
Drain plug 25 ± 2.5 Nm
Y220_01047

AFFECTED VIN
DI01-34
Accessories - Removal and Installation
PCV valve and oil separator EGR valve pipe (LH, Center, RH)
Power steering pump

Turbo charger
Cooling fan clutch
Auto tensioner
Alternator
Fuel return hose
Cable and connector
Oil filter assembly
EGR valve
Air conditioner compressor Start motor
Mounting bracket
Y220_01048

AFFECTED VIN
DI01-35
• The engine accessories can be removed without any specific order. In general, remove the components from top
to bottom. However, be careful not to splash the lubricants to engine and body when disassembly. Especially,
avoid getting into other components.
Removal and Installation Order of Major Accessories
1. Vacuum Modulator * Camshaft Position Sensor

* Crankshaft Position Sensor
* Injector Fuel Line Connector
* Glow Plug Connector
2. Engine Cables and Connectors * Fuel Return Hose
* High/Low Pressure Hoses in HP Pump
* Ground Cables
* Fuel Pressure Sensor Connector
3. Fuel Hoses * Booster Pressure Sensor Connector
* Knock Sensor Connector
* Coolant Temperature Sensor Connector
* HP Pump: Fuel Temperature Sensor (Green)
3-1. EGR Valve Assembly IMV (Brown)
4. Oil Filter Assembly
4-1. Belt Tensioning Assembly
5. Power Steering Pump Assembly
6. Air Conditioner Compressor Assembly
7. PCV Valve Assembly + Oil Dipstick Tube
8. Turbo Charger Alternator Assembly

AFFECTED VIN
DI01-36
1. Remove the fuel pipes.

A. Remove the fuel supply pipes between each
cylinder and common rail with a special tool.
Installation Notice
Y220_01049
Notice
1. Plug the openings of injector nozzle and common

rail with sealing caps after removed the fuel pipes.
Y220_01050
2. Replace the pipes with new ones. Be careful not

to be mixed the fuel pipes because the pipe
appearance of #1 and #3 cylinders and #2 and #4
are same each other.
No. 1 No. 3 No. 2 No. 4 No. 5

Y220_01051
B. Remove the high fuel pressure pipe mounting bolts

with a special tool.
- High fuel pressure supply pipe at common rail
side
Installation Notice
Tightening torque 40 ± 4 Nm
Y220_01052

AFFECTED VIN
DI01-37
C. High fuel pressure supply pipe at HP pump side

Installation Notice
Y220_01053
D. Unscrew the bracket mounting bolts and remove the

high fuel pressure supply pipes.
Note
Special tool: Fuel pipe remover and installer
Y220_01055
Y220_01054

AFFECTED VIN
DI01-38
2. Disconnect the vacuum hoses and module cables from the vacuum modulator.
Notice
Put the installation marks on the modulator hoses and connectors.
To EGR valve
EGR vacuum booster
vacuum modulator
Turbo charger
booster vacuum
modulator
From vacuum pump
To turbo charger
booster
Y220_01056
A. Remove the vacuum modulator bracket.

(Upper: 10 M x 2, Lower: 10M x 2)
Installation Notice
Upper bolt 25 ± 2.5 Nm

Lower bolt 25 ± 2.5 Nm
Y220_01057

AFFECTED VIN
DI01-39
3. Disconnect the wiring harnesses and connectors from the engine.
Fuel return hose Injector fuel line Glow plug connector

connector
Camshaft position Crankshaft position

sensor sensor
HP pump connector Oil pressure switch
Fuel temperature
Sensor
IMV
Coolant temperature Booster pressure sensor Fuel pressure sensor

Knock sensor connector connector connector
sensor connector
Y220_01058

AFFECTED VIN
DI01-40
A. Remove the cable assembly from the engine.
Important
1. If possible, remove the cables after removing the
fuel pipes. It make the operation easier and protect
the cables and connectors.
Y220_01059
2. Remove the cable screws and ground cable, and

then remove the engine cable assembly.
Notice
• Be careful not to damage the HP pump connecting
pipe (venturi) while removing the fuel hose from
the HP pump.
Y220_01060
4. Disconnect the high and low fuel pressure hoses from

the HP pump.
Notice
• Be careful not to damage the hose connections.

• Plug the openings in HP pump immediately after
disconnecting the hoses.
Y220_01061

AFFECTED VIN
DI01-41
5. Remove the EGR valve and EGR valve pipe.

A. Disconnect the vacuum hose from the EGR valve.
B. Unscrew the EGR valve bolts and EGR #1 pipe
connecting bolts and remove the EGR valve and steel
gasket.
Installation Notice
EGR valve bolt 25 ± 2.5 Nm

EGR valve and
25 ± 2.5 Nm
center pipe bolt
Y220_01062
C. Remove the EGR valve #1 pipe.

Installation Notice
Center pipe bolt 35 ± 3.5 Nm

Center pipe and #1 pipe
35 ± 3.5 Nm
bolt and nut
Notice
The EGR #2 pipe should be replaced with new one.
Y220_01063
D. Unscrew the EGR valve #3 pipe (2) mounting bolts

and remove the pipe from the exhaust manifold.
Installation Notice
Notice
1. The EGR #3 pipe should be replaced with new
one.
2. Make sure that the convex surface of new steel Y220_01064
gasket is facing to the bolts.
6. Remove the oil filter assembly.

A. Remove the oil cooler hose.
Y220_01065

AFFECTED VIN
DI01-42
B. Remove the oil filter assembly mounting bolts.
Notice
Be careful not to flow out the residual oil from the

engine. If flown out, immediately wipe it out.
Y220_01066
C. Remove the oil filter assembly from the cylinder block.

Installation Notice
- Replace the oil filter gasket with new one.
Y220_01067
7. Remove the belt tensioning device.

A. Remove the shock absorber lower mounting bolt.
Installation Notice
Y220_01068
B. Remove the shock absorber upper mounting bolt.

Installation Notice
Y220_01069

AFFECTED VIN
DI01-43
C. Remove the belt tensioning device.

Notice
• To prevent the oil leaks, store the removed shock

absorber assembly with standing up.
• For air bleeding, pump the shock absorber around
3 times after installation.
• Be careful not to damage the rubber parts of the
shock absorber when removing.
• To prevent the oil leaks, remove the bolts from bottom
to top section. On the contrary, when installing,
tighten the bolts from top to bottom section. Y220_01070
7. Remove the power steering pump assembly.

A. Remove the power steering pump mounting bolts.
Installation Notice
Notice
Be careful not to flow out the oil.
Y220_01071
B. Remove the power steering pump assembly from the

engine.
Notice
To prevent the oil leaks, store the removed power

steering pump assembly with standing up.
Y220_01072
8. Remove the air conditioner compressor assembly.

A. Unscrew the bolts and remove the air conditioner
compressor assembly.
Installation Notice
Y220_01073

AFFECTED VIN
DI01-44
B. Unscrew the bolts and remove the air conditioner

mounting bracket.
Installation Notice
Front bolt 25 ± 2.5 Nm

Side bolt 25 ± 2.5 Nm
Y220_01074
9. Remove the PCV valve assembly.

A. Remove the PCV valve hose.
Y220_01075
B. Remove the PCV valve hose connected to the engine

oil hose.
Y220_01076
C. Unscrew the PCV valve mounting bolts and remove

the PCV valve assembly.
Installation Notice
Y220_01077

AFFECTED VIN
DI01-45
10. Remove the oil dipstick tube assembly.

Unscrew the bracket bolts and remove the dipstick tube
with O-ring.
Installation Notice
Insert new O-ring into the oil dipstick tube before
installation.
Y220_01078
Installation Notice
Y220_01079
11. Remove the turbo charger assembly.

A. Unscrew the bolts and remove the oil supply pipe.
Installation Notice
Upper bolt (M19) 25 ± 2.5 Nm

Lower bolt (M17) 20 ± 2.0 Nm
Y220_01080
B. Unscrew the bolts and remove the oil return pipe.

Installation Notice
• Make sure to install the gasket with correct direction.
Y220_01081

AFFECTED VIN
DI01-46
C. Unscrew the turbo charger mounting bracket bolts.

Installation Notice
Y220_01082
D. Unscrew the turbo charger mounting bolts to exhaust

manifold.
Notice
Use only 12 1/2 wrench.
Installation Notice
Y220_01083
E. Remove the turbo charger assembly.
Y220_01084
12. Remove the alternator assembly.

A. Unscrew the bolts and remove the alternator.
Note
Alternator Capacity: 140 A
Installation Notice
Y220_01085

AFFECTED VIN
DI01-47
B. Remove the alternator mounting bracket.

Installation Notice
M13 bolt 25 ± 2.5 Nm

Torx 6 bolt 25 ± 2.5 Nm
Y220_01086

AFFECTED VIN
DI01-48
Engine - Disassembly and Reassembly

1. Unscrew the injector nozzle holder bolts (12-sided) and
remove the injector bracket.
Installation Notice
9 ± 1.0 Nm,
Tightening torque
190° + 10°
Y220_01089
2. Remove the injectors with a injector extractor (special

tool).
Notice
• Be careful not to take off the sealing caps on the

injectors and fuel system.
• Replace the copper washers with new ones when
installing.
Y220_01090
3. If the copper washer is in injector hole, remove it with a

special tool as shown in the figure.
Y220_01092

AFFECTED VIN
DI01-49
4. Remove the glow plugs with a special tool.

Installation Notice
Y220_01091
5. Unscrew the Torx bolts and remove the common rail from
the engine.
Installation Notice
Notice
Plug the openings with sealing cap.
Y220_01087
6. Remove the booster sensor from the engine.

Installation Notice
Y220_01088
7. Unscrew the bolt and remove the camshaft position

sensor.
Installation Notice
• Apply Loctite on the thread before installation.
Y220_01093

AFFECTED VIN
DI01-50
8. Unscrew the bolts and remove the cooling fan pulley while
holding it with a special tool.
Y220_01094
9. Remove the cooling fan belt idle pulley while holding it

Y220_01095
10. Unscrew the bolts and remove the cooling fan bracket
assembly (timing chain cover).
Y220_01096
11. Unscrew the bolts and remove the cylinder head cover.
Y220_01097

AFFECTED VIN
DI01-51
12. Turn over the engine and remove the oil pan.
Installation Notice
Tightening torque Nm
M6 x 20: 24 EA 10 ± 1.0
M6 x 35: 2 EA 10 ± 1.0
M6 x 85: 2 EA 10 ± 1.0
M8 x 40: 4 EA 25 ± 2.5
Y220_01100
Installation Notice
Remove the oil seal residues from the oil pan and
apply the liquid gasket on the parting surface.
Y220_01101
13. Unscrew the nuts and remove the exhaust manifold.

Installation Notice
Y220_01102
Notice
The exhaust manifold gasket is removed along with

the exhaust manifold. Mark the installation direction
to prevent wrong installation. Otherwise, it may cause
a sealing trouble.
Y220_01103

AFFECTED VIN
DI01-52
14. Unscrew the bolts and remove the thermostat.

Installation Notice
Notice
Be careful not to flow out the residual coolant.
Y220_01104
15. Unscrew the bolts and remove the water pump.

Installation Notice
Y220_01105
16. Unscrew the bolts and remove the water pump housing.
Installation Notice
Notice
Be careful not to flow out the residual coolant.
Y220_01106
17. Unscrew the bolts and remove the coolant inlet port from
the intake manifold.
Installation Notice
Notice
Be careful not to get the coolant into the intake
manifold and engine.
Y220_01107

AFFECTED VIN
DI01-53
18. Unscrew the bolts and remove the intake manifold

assembly.
Installation Notice
Y220_01108
Notice
Replace the gasket with new one once removed.
Y220_01109
19. Remove the vacuum pump from the cylinder head.

Installation Notice
Y220_01110
20. Install the engine lock (special tool) onto the flywheel
ring gear so that the engine will not rotate.
Y220_01111

AFFECTED VIN
DI01-54
21. Remove the chain tensioner.

Preceding works: removal of EGR pipe and oil dipstick
tube
Y220_01119
22. Pull out the lock pin and remove the upper chain guide
bracket.
Y220_01112
23. Unscrew the bolt and remove the intake camshaft

sprocket.
Installation Notice
25 ± 2.5 Nm,
Tightening torque
90° + 10°
Y220_01113
24. Unscrew the bolt and remove the exhaust camshaft

sprocket.
Installation Notice
25 ± 2.5 Nm,
Tightening torque
90° + 10°
Y220_01114

AFFECTED VIN
DI01-55
25. Remove the camshaft bearing cap bolts so that the

tightening force can be relieved evenly. Exhaust
• Intake: #1, #3, #6
• Exhaust: #7, #9, #12
* However, there is no specific removal sequence.
Intake Y220_01115
• Intake: #2, #4, #5

• Exhaust: #8, #10, #11
* Do not remove the bolts at a time completely. Remove
them step by step evenly or camshaft can be seriously
damaged.
Installation Notice
Y220_01116
26. Remove the intake and exhaust camshafts from the

cylinder head.
Y220_01117
27. Remove the finger follower and the HLA device.

Notice
• Avoid contact with hot metal parts when removing
the HLA device immediately after stopping the
engine.
• Be careful not to be contaminated by foreign
materials.
• To prevent the oil leaks, store the removed finger
follower and HLA device with standing up.
• If the HLA can be easily pressed in by hand, it
indicates the oil inside of HLA has been flown out.
In this case, replace it with new one. Y220_01118

AFFECTED VIN
DI01-56
28. Pull out the pin and remove the timing chain guide from
the engine.
Y220_01120
29. Remove the cylinder head bolts according to the

numerical sequence.
Installation Notice
M8 x 25: 2 EA 25 ± 2.5
M8 x 50: 2 EA 25 ± 2.5
M12 x 177: 11 EA
85 ± 5 Nm,
M12 x 158: 1 EA
3 x 90° + 10°
(Vacuum pump side)
Y220_01121
30. Measure the length of cylinder head bolts.

• If the maximum length is exceeded by 2 mm, replace
the cylinder head bolt.
Length when new Maximum Limit

177 mm 179 mm
158 mm 160 mm
Y220_01122
31. Remove the cylinder head.
Notice
• Inspect the cylinder head surface.

• Store the removed injectors and glow plugs so that
they will not be damaged.
Y220_01123

AFFECTED VIN
DI01-57
32. Measure the piston protrusion from the parting surface.

• Specified Value: 0.765 ~ 1.055 mm
Y220_01124
33. Remove the cylinder head gasket.
Installation Notice
• Replace the cylinder head gasket with new one.
Make sure to place the “TOP” mark upward.
1. Put the steel gasket on the cylinder block and
position the cylinder head.
Y220_01125
2. Tighten the cylinder head bolts to specified torque

and torque angle.
Step 1 20 ± 2.0 Nm
Tightening torque Step 2 85 ± 5.0 Nm
Step 3 90 ± (3 times) + 10°
• Apply the oil on the bolt thread when installing.

• Always insert new washer first.
• The bolts (12) at vacuum pump side are shorter
than others.
Y220_01126
34. Turn over the engine and remove the baffle plate.
Installation Notice
Y220_01127

AFFECTED VIN
DI01-58
35. Unscrew the bolts and remove the oil strainer assembly.
Installation Notice
Y220_01128
36. Remove the piston assembly from the cylinder block.

A. Unscrew the bearing cap bolts.
Installation Notice
Step 1 55 ± 5.0 Nm
Step 2 90° + 10°
* Tighten the bolts from #1 cap.
Y220_01129
Installation Notice
* Align the oil grooves in bearing cap and connecting
rod.
B. Remove the bearing caps and lower bearing shells.
Y220_01130
C. Remove the piston assembly through the cylinder.
Notice
Do not mix up upper and lower crankshaft bearing
shells.
Y220_01131

AFFECTED VIN
DI01-59
D. Remove the snap ring piston pin from the piston.

E. Disassemble the piston and connecting rod.
F. Remove the piston rings from the piston.
Installation Notice
Replace the piston ring, bearing and snap ring with
new ones.
Y220_01132
37. Lock the flywheel and remove the center bolt and
crankshaft pulley.
Installation Notice
325 ± 33 Nm,
Tightening torque
90° + 10°
Y220_01133
38. Remove the timing chain cover assembly.

A. Remove the cover bolts.
Installation Notice
Y220_01134
B. Hold the timing chain and remove the timing chain

cover by tapping it with a rubber hammer and a
screwdriver.
Installation Notice
Apply the sealant on the parting surface.
Y220_01135

AFFECTED VIN
DI01-60
39. Remove the timing chain guide rail and timing chain.
Y220_01136
40. Remove the HP pump bolts and the HP pump bracket

bolts.
Y220_01138
• Remove the HP pump assembly.
Y220_01139
41. Remove the crankshaft sprocket with a special tool.
Y220_01137

AFFECTED VIN
DI01-61
42. Remove the flywheel and the crankshaft strainer.

Installation Notice
45 ± 5.0 Nm,
Tightening torque
90° + 10°
43. Unscrew the bolts and remove the crankshaft bearing

caps.
Installation Notice
55 ± 5.0 Nm,
Tightening torque
90° + 10°
Y220_01140
Notice
• Remove the bearing cap bolts from inside to outside

with a pair.
• Do not mix up the crankshaft bearing caps and
shells.
Y220_01141
Note
• Install in the reverse order of removal.

• Tighten the fasteners with the specified tightening torques.
• Replace the gaskets and bearings with new ones.
• Make sure to install the gaskets in correct direction.

AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SECTION DI02
ENGINE HOUSING
DI02-1
SECTION
00 DI02
ENGINE HOUSING
Table of Contents
CYLINDER HEAD/CYLINDER BLOCK ....................... DI02-3

Cylinder head .......................................................... DI02-3
Camshaft assembly .............................................. DI02-17
Timing chain assembly .......................................... DI02-25
Cylinder block ....................................................... DI02-29
CRANKSHAFT ........................................................... DI02-32
Arrangement of thrust washers and bearings ...... DI02-33
Torsional vibration damper ................................... DI02-38
FLYWHEEL ................................................................ DI02-42
Dual mass flywheel (DMF, Manual transmission
equipped vehicle) ................................................. DI02-42
PISTON AND CONNECTING ROD ............................ DI02-44
Piston ring ............................................................. DI02-45
Cylinder inner diameter and piston size ............... DI02-46
HIGH PRESSURE PUMP (HPP) ............................... DI02-51
Components locator ............................................. DI02-51
ENGINE HOUSING CHANGED BY

AFFECTED VIN
DI02-3
CYLINDER HEAD/CYLINDER BLOCK

CYLINDER HEAD
Cylinder head bolt
Oil return check valve
Y220_02001
System Characteristics
• 4-valve DOHC valve mechanism Intake port
• Swirl and tangential port

• 4-bolt type cylinder head bolt
• Water jacket integrated casting
• Integrated chain housing and cylinder head
• Oil gallery: drilled and sealing with cap and screw plug Exhaust port
Y220_02002

AFFECTED VIN
DI02-4
Cylinder Head Pressure Leakage Test

Preceding Works:
- Removal of cylinders
- Removal of intake and exhaust manifold
- Removal of valves
Test Procedures
1. Place the pressure plate on a flat-bed work bench.
Y220_02003
2. Install the cylinder head on the pressure plate.
3. Immerse the cylinder head with the pressure plate into

warm water (approx. 60°C) and pressurize with
compressed air to 2 bar.
Notice
Examine the cylinder head for air bubbling. If the air

bubbles are seen, replace the cylinder head.
Y220_02004
CHANGED BY ENGINE HOUSING

AFFECTED VIN
DI02-5
Cylinder Head Parting Surface Check

Specifications
Height “A” (cylinder head parting surface - cylinder head cover parting surface) 142.9 ~ 143.1 mm
Minimum height after machining 142.4 mm
Permissible unevenness of parting surface in longitudinal direction 0.08 mm
in transverse direction 0.0 mm
Permissible variation of parallelism of top parting surface to bottom in longitu-
within 0.1 mm
dinal direction
Peak-to-valley height 0.004 mm
Valve recess “a” Intake valve 0.1 ~ 0.7 mm
Exhaust valve 0.1 ~ 0.7 mm
Measurement
1. Measure the cylinder head height “A”.
Limit Over 142.4 mm
Notice
If the height is less than the limit, the cylinder head

must be replaced.
Y220_02005
2. Insert the valves into the valve guides and measure the
recesses.
Valve recess “a” 0.1 ~ 0.7 mm
Notice
If the measured value is out of the specified range,

machine the valve seat as much as necessary until
the specified value is achieved.
Y220_02006

AFFECTED VIN
DI02-6
Cylinder Head
- Disassembly and Reassembly
Disassembly
Preceding Works:
- Removal of fan belt
- Removal of fuel supply and return lines
- Removal of EGR related pipes
- Removal of intake manifold mounting bracket
- Removal of injector fuel line and connector, and glow plug
Y220_02007 connector
Notice
• Plug the openings of injector holes and common

rail with the protective caps.
1. Remove the cylinder head cover.
Y220_02008
2. Remove the camshaft position sensor.

• The intake manifold can be interfered by the sensor
when installing.
Y220_02010
3. Mark on the intake camshaft sprocket and exhaust

camshaft sprocket for timing setting during installation.
Y220_02011

AFFECTED VIN
DI02-7

Preceding work: removal of EGR pipe and oil dipstick tube
Y220_02012
5. Hold the camshafts and remove the intake camshaft

sprocket and exhaust camshaft sprocket.
Y220_02013
6. Pull out the lock pins with a sliding hammer and remove
the upper guide rail.
Notice
Correctly align the electronic control module onto

the shift plate by using two central pins when
installing.
Y220_02014
7. Remove the oil cooler, then remove the intake manifold.

• The intake manifold can be interfered by the cylinder
head bolt (M8 x 50).
Y220_02015

AFFECTED VIN
DI02-8
8. Remove the cylinder head bolts according to the

numerical sequence.
M8 x 25 : 2 EA
M8 x 50 : 2 EA
M12 x 177 : 11 EA
M12 x 158 : 1 EA (Vacuum pump side)
Y220_02016
9. Measure the length of cylinder head bolts.

• If the maximum length is exceeded by 2 mm, replace
the cylinder head bolt.
Length when new Maximum Limit

177 mm 179 mm
158 mm 160 mm
Y220_02017
10. Remove the cylinder head.
Notice
• Inspect the cylinder head surface.

• Store the removed injectors and glow plugs so that
they will not be damaged.
Y220_02018
11. Measure the piston protrusion from the parting surface.

• Specified Value: 0.765 ~ 1.055 mm
Y220_02019

AFFECTED VIN
DI02-9
Reassembly
1. Install the cylinder head with the steel gasket.
Notice
Make sure to place the “TOP” mark upward.
Y220_02020
2. Tighten the cylinder head bolts to specified torque and

torque angle.
Step 1 20 ± 2.0 Nm
Tightening torque Step 2 85 ± 5.0 Nm
Step 3 270° (90° x 3) + 10°
Notice
• Apply the oil on the bolt thread when installing.

• Always insert new washer first.
• The bolts (12) at vacuum pump side are shorter than
others. Y220_02021
3. Install the HLA device and finger follower. Check the HLA
device with the diagnosis procedures before installation.
Notice
• Put the cylinder head on the locating pins.
Y220_02022
4. Tighten the camshaft bearing cap bolts.

• Intake: #2, #4, #5
• Exhaust: #8, #10, #11
Y220_02023

AFFECTED VIN
DI02-10
• Exhaust: #1, #3, #6

Exhaust • Intake: #7, #9, #12
Notice
Check the finger follower positions and align if

needed.
Intake Y220_02024
5. Install the intake and exhaust camshaft sprockets and

the timing chain.
Tightening torque 25 Nm + 90°
Notice
• If the sprocket bolt is stretched over 0.9 mm, replace
it with new one.
• Always install the intake camshaft sprocket first.
• Ensure that the markings on camshaft sprocket and
timing chain are aligned.
• Make sure that the timing chain is securely seated
Y220_02025 on the guide rail.
6. Rotate the crankshaft pulley two revolutions and ensure

that the OT mark on the crankshaft pulley and the OT
mark on the camshaft pulley are aligned.
Notice
If the markings are not aligned, reinstall the cylinder

head.
Y220_02026
7. Place the bearing cap with the OT marks on both

camshafts facing upward.
Notice
• Apply the sealant on the cap (#12) for the vacuum
pump when installing.
• Apply the oil on the bearing journals before
installation.
Y220_02027

AFFECTED VIN
DI02-11
8. Fit the timing chain onto the camshaft sprockets and

install the upper guide rail.
• Install the clamping guide rail pin.
Notice
• Install the guide rail with slanted side facing

forward.
• Be careful not to change the timing of HP pump
when fitting the timing chain.
Y220_02028
9. Tighten the intake and exhaust camshaft sprocket bolts.
25 ± 2.5 Nm,
Tightening torque
90° + 10°
Y220_02029
10. Install the camshaft position sensor.

11. Apply the Loctite to the bolt and tighten it.
12. Check the intake camshaft before installing the vacuum

pump.
Y220_02030
13. Install the intake manifold. Install the oil cooler with new
gasket.
Notice
Ensure that there is no leaks around the coolant line

for #1 cylinder
Y220_02031

AFFECTED VIN
DI02-12
14. Install the chain tensioner.
Y220_02032
15. Install the cylinder head cover assembly.

16. Install the rubber gasket.
Y220_02033
17. Tighten the cylinder head cover bolts.
Notice
• Apply the sealant to the bolts for the vacuum pump

and the timing chain cover.
Y220_02034
18. Check the parting surface of the #12 bearing cap and the
cylinder head for contacting.
19. Check if the O-ring is installed in the vacuum pump.
20. Install the vacuum pump with the key groove aligned.
21. Tighten the vacuum pump mounting bolts.
Y220_02037

AFFECTED VIN
DI02-13
22. Install the PCV valve assembly on the cylinder head.
Y220_02035
23. Engage the engine oil hose and the PCV valve hose.
Y220_02036
24. Remove the protective caps and install the new fuel supply
pipes.
Notice
• To keep the cleanness and protect the components,

the fuel pipes should be replaced with new ones.
• Be careful not to be mixed the fuel pipes because
the pipe appearance of #1 and #3 cylinders and #2
and #4 are same each other.
Y220_02038

AFFECTED VIN
DI02-14
Intake/Exhaust - Removal/Installation
1. Remove the cylinder head assembly.
Y220_02039
2. Install the removed cylinder head on the assembly board

(special tool) and set the supporting bar and lever (special
tool) on the cylinder head.
Y220_02040
3. Push the valve spring seat down with the lever and remove
the valve cotter, valve seat and valve spring.
Y220_02041
4. Remove the valves from the cylinder head.
Y220_02042

AFFECTED VIN
DI02-15
Special Tools and Equipment

Name and Part Number Application
Compression pressure measur-

ing adapter and gauge
Y220_02043 Y220_02044
Pressure plate (cylinder head

pressure leakage test)
Y220_02045 Y220_02046
Pressure plate (intake camshaft

pressure leakage test
Y220_02047 Y220_02048
Pressure plate (exhaust camshaft

pressure leakage test)
Y220_02049 Y220_02050

AFFECTED VIN
DI02-16
Cylinder head hanger
Y220_02051 Y220_02052
Supporting bar and lever
Y220_02053 Y220_02054
Guide pin extractor
Y220_02055 Y220_02056
Intake manifold guide pin
Y220_02057 Y220_02058

AFFECTED VIN
DI02-17
CAMSHAFT ASSEMBLY
Preceding Work: Removal of cylinder head cover
Intake camshaft and

Finger follower and HLA exhaust camshaft
Camshaft sprockets
Cylinder head
Camshaft position sensor Chain tensioner
Y220_02059

AFFECTED VIN
DI02-18
Camshaft Position Sensor
Gap
Hall voltage
<Location of camshaft position sensor> <Operation principle of hall sensor>

Y220_02060
The camshaft position sensor uses hall-effect to set the camshaft position and metallic-magnetic-material sensor end is
attached on the camshaft and then rotates with it. If sensor protrusion passes camshaft position sensor’s semi-conduc-
tor wafer, magnetic field changes direction of electron on the semi-conductor wafer to the current flow direction that
passes through wafer from the right angle. When operation power is supplied from camshaft position sensor, camshaft
hall sensor generates signal voltage. The signal voltage will be 0V if protrusion and camshaft position sensor are near
and 5 V if apart.
ECU can recognize that the No. 1 cylinder is under compression stroke by using this voltage signal (hall voltage).
The rotating speed of camshaft is half of the crankshaft and controls engine’s intake and exhaust valves. By installing
sensor on the camshaft, can recognize specific cylinder’s status, compression stroke or exhaust stroke, by using
camshaft position when the piston is moving toward TDC (OT). Especially when started first, it is difficult to calculate the
stroke of a specific cylinder with only crankshaft position sensor.
Accordingly, camshaft position sensor is necessary to identify the cylinders correctly during initial starting. However,
when engine is started, ECU learns every cylinder of the engine with crankshaft position sensor signals so can run the
engine even though the camshaft position sensor is defective during engine running.
Pulse generation Cam angle ± 6°

Sensor air gap 0.2 ~ 1.8 mm
Tightening torque 10 ~ 14 Nm
Operating temperature - 40 ~ 130°C
Ground
Camshaft sensor
<Circuit diagram of camshaft position sensor>

Y220_02061

AFFECTED VIN
DI02-19
Removal
Preceding Works:
- Removal of fan belt
- Removal of fuel supply and return lines
- Removal of intake manifold mounting bracket
1. Remove the injector fuel line and connector, and glow

plug connector
Notice
Plug the openings of injector holes and common rail
with the protective caps.
Y220_02062
2. Remove the cylinder head cover.
Y220_02063
3. Remove the camshaft position sensor.
Y220_02065

AFFECTED VIN
DI02-20
4. Mark on the intake camshaft sprocket and exhaust

camshaft sprocket for timing setting during installation.
Y220_02066
Preceding work: removal of EGR pipe and oil dipstick tube
Y220_02067
6. Hold the camshafts and remove the intake camshaft

sprocket and exhaust camshaft sprocket.
Y220_02068
7. Remove the camshaft bearing cap bolts so that the

Intake tightening force can be relieved evenly.
• Intake: #1, #3, #6
• Exhaust: #7, #9, #12
* However, there is no specific removal sequence.
Exhaust
Y220_02069

AFFECTED VIN
DI02-21
• Intake: #2, #4, #5

• Exhaust: #8, #10, #11
* Do not remove the bolts at a time completely. Remove
them step by step evenly or camshaft can be seriously
damaged.
8. Remove the intake and exhaust camshafts from the

cylinder head.
Y220_02070
9. Remove the finger follower and the HLA device.
Notice
Avoid contact with hot metal parts when removing

the HLA device immediately after stopping the
engine.
Y220_02071

AFFECTED VIN
DI02-22
Installation
1. Install the HLA device and finger follower. Check the HLA
device with the diagnosis procedures before installation.
Notice
• Put the cylinder head on the locating pins.
Y220_02072
2. Place the bearing cap with the OT marks on both

camshafts facing upward.
Notice
• Apply the sealant on the cap (#12) for the vacuum

pump when installing.
• Apply the oil on the bearing journals before
installation.
Y220_02073
3. Tighten the camshaft bearing cap bolts.

• Intake: #2, #4, #5
• Exhaust: #8, #10, #11
1 2 3 4 5 6
7 8 9 10 11 12
Y220_02074
• Intake: #1, #3, #6

Intake
• Exhaust: #7, #9, #12
1 2 3 4 5 6 Tightening torque 25 Nm
Notice
7 8 9 10 11 12
Check the finger follower positions and align if
needed.
Exhaust Y220_02075

AFFECTED VIN
DI02-23
4. Install the intake and exhaust camshaft sprockets and

the timing chain.
Tightening torque 25 Nm + 90° + 10°
Notice
• If the sprocket bolt is stretched over 0.9 mm, replace
it with new one.
• Always install the intake camshaft sprocket first.
• Ensure that the markings on camshaft sprocket and
timing chain are aligned.
• Make sure that the timing chain is securely seated Y220_02076
on the guide rail.
5. Rotate the crankshaft pulley two revolutions and ensure

that the OT mark on the crankshaft pulley and the OT
mark on the camshaft pulley are aligned.
Notice
If the markings are not aligned, reinstall the cylinder

head.
Y220_02077
Y220_02079

AFFECTED VIN
DI02-24

HLA remover
Y220_02080 Y220_02081
Stem seal drift
Y220_02082 Y220_02083

AFFECTED VIN
DI02-25
TIMING CHAIN ASSEMBLY

Chain Drive System
System Layout
Oil injecting direction
Y220_02084
1. Exhaust camshaft sprocket 7. Oil pump tensioner

2. Upper guide rail 8. Oil pump sprocket
3. Intake camshaft sprocket 9. Crankshaft sprocket
4. Clamping guide rail 10. Oil nozzle
5. HP pump sprocket 11. Tensioner guide rail
6. Lower guide rail 12. Chain tensioner

AFFECTED VIN
DI02-26
Chain
• Chain type: Double Bush
• Pitch: 9.525 mm
• Load limits: 19,000 N
• No. of links: 144 EA
• Overall length: 1371.6 mm
• Replace when the chain is extended by 0.5 % from overall length (Replace if extended by over 6.858 mm)
Chain tensioner
Check valve
* Check valve opening pressure: 0.2 ~ 0.5 bar
Y220_02085
The major function of tensioner is optimizing the movement of chain drive system by using spring constant and oil
pressure in the tensioner.
The tensioner performs function of adjusting chain tension to be always tight, not loose, while engine running. By doing
so, can reduce wears of each guide rail and sprocket.
65 ± 5.0 Nm
Tightening torque
(Installed on the cylinder head)
Guide rail
Guide rail is used to optimize the movement of chain drive system like tensioner.
Guide rail can prevent chain slap when chain is extended and reduce chain wears.
Guide rail is needed especially when the distance between the sprockets are too long.
The material is plastic.
• Location of guide rail

- Tensioner guide rail: Between crankshaft sprocket and exhaust camshaft sprocket
- Upper guide rail: Between exhaust camshaft sprocket and intake camshaft sprocket
- Clamping guide rail: Between intake camshaft sprocket and HP pump sprocket
- Lower guide rail: Between HP pump sprocket and crankshaft sprocket

AFFECTED VIN
DI02-27
Timing setting
Sprocket marking: 4 points

(Gold marking)
<Timing marking points on chain>

Y220_02086
• Check marking links on the chain (Gold marking)

• Locate a point with two continuous marking links and align it to a marking on crankshaft sprocket ( )
• Align respective marking link to each camshaft sprocket (intake and exhaust) marking ( )
• Align another marking link to HP pump sprocket marking ( )

AFFECTED VIN
DI02-28
Removal and Installation

1. Remove the cylinder head assembly.
2. Remove the oil pan.
3. Remove the chain guide rail with a sliding hammer.
4. Remove the chain cover.
Y220_02087
5. Remove the oil pump drive chain.

6. Remove the upper guide rail while pushing the retaining
spring with a screwdriver.
7. Remove the lower guide rail.
8. Remove the oil pump drive chain.
Y220_02088
9. Remove the tensioning guide rail.
Y220_02089
10. Remove the timing chain.

11. Install in the reverse order of removal.
* Thoroughly clean the removed components before

installing.
Y220_02090

AFFECTED VIN
DI02-29
CYLINDER BLOCK
Deep head bolt thread to prevent the

deformation at cylinder bore surfaces
Internal and external ribs considered Water jacket design to increase

vibration and strength the cooling efficiency
Cambering type skirt to reduce the noise
Y220_02091
• Rib design by considering strength against engine • Reinforcement of strength
vibrations and weight - Main bearing housing / Main bearing cap
• Cambering type skirt design on case housing wall to - Extended main bearing cap bolt
reduce the engine noise
• Water jacket design to increase the cooling efficiency
• Reducing the noise, vibration and harshness (NVH)
of cylinder bore bridge
- Minimize the vibration by adding external ribs
• Deep head bolt thread to prevent the deformation at
cylinder bore surfaces - Adding the ribs around oil pan parting surface

AFFECTED VIN
DI02-30
Knock Sensor
Two knock sensors are located on the cylinder block (intake manifold side).
To detect engine vibration under abnormal combustion, knock sensor has piezoelectric element fixed on the
vibration plate and this vibration plate is fixed on the base. If happens knocking, pistons or connecting rods
vibrate and occurs heavy sounds that hit metal. Knock sensor is used to detect those knockings caused by
abnormal combustions. It controls idling stabilities and turns on the engine warning light when detects injector
damages. And also controls pilot injection very precisely during MAP learning.
When knock sensor is defective, engine ECU corrects injection timing based on MAP values like engine speed,
intake air volume and coolant temperature.
Before checking the knock sensor unit, be sure to check the tightening torque of the sensor and connector
connecting conditions.
Insulating resistance Min. 1MΩ

Resonance frequency 25 kHz
26 ± 8 mV/g (at 5 kHz)
Output voltage 22 ~ 37 mV/g (3 ~ 10 kHz)
22 ~ 57 mV/g (10 ~ 20 kHz)
<Location of knock sensor>

Y220_02092
1. Sensor housing 7. Piezo element

2. Nut 8. Lower contact plate
3. Disc spring 9. Body
4. Weight 10. Terminal
5. Insulation disc 11. Resister
6. Upper contact plate

AFFECTED VIN
DI02-31
Notice
The knock sensor should be tightened with the specified tightening torque. Otherwise, the engine output may
be decreased and the “ENGINE CHECK” warning lamp may come on. The internal resistance of the sensor is
approx. 4.7 kΩ.
Ground
Knock sensor
Signal
Signal
Knock sensor
Ground
<Circuit diagram of knock sensor>

Y220_02093

AFFECTED VIN
DI02-32
CRANKSHAFT
Preceding Works: Removal of end cover
Removal of pistons
Removal of crankshaft sprocket
Y220_02094
3. Crankshaft main bearing shells, upper 7. Lower thrust bearing

4. Upper thrust bearing 8. Crankshaft main bearing cap
5. Crankshaft 9. Crankshaft thrust bearing cap
6. Crankshaft main bearing shells, lower 10. 12-sided stretch bolt ....... 55 ± 5.0 Nm, 90° + 10°

AFFECTED VIN
DI02-33
ARRANGEMENT OF THRUST WASHERS AND BEARINGS
Y220_02095
1. Crankshaft 4. Crankshaft main bearing shells, lower

2. Crankshaft main bearing shells, upper 5. Lower thrust bearing
3. Upper thrust bearing
Notice
The clearance between bearing shell and bore and between
bearing shell and journal are various. Refer to the table
on next page to select bearings when installing.

AFFECTED VIN
DI02-34
Dimensions of Crankshaft Main Bearing

(mm)
Color Crankshaft Journal Upper Main Bearing Lower Main Bearing
Blue 57.965 ~ 57.960 2.260 ~ 2.255 2.260 ~ 2.255
Yellow 57.960 ~ 57.955 2.265 ~ 2.260 2.265 ~ 2.260
Red 57.955 ~ 57.950 2.270 ~ 2.265 2.270 ~ 2.265
White 57.950 ~ 57.945 - 2.275 ~ 2.270
Violet 57.945 ~ 57.940 - 2.280 ~ 2.275
Bearing Clearance
(mm)
Description Crankshaft Bearing Thrust Bearing
When new 0.027 ~ 0.051 0.026 ~ 0.068
Radial clearance
Wear limit Max. 0.070 Max. 0.080
When new 0.100 ~ 0.254 -
Axial clearance
Wear limit Max. 0.300 -
Matching the Fit Bearing Journal Width to Thrust Washers

(mm)
Fit bearing Journal Width Thrust Washer Thickness
24.500 ~ 24.533 2.15
24.600 ~ 24.633 2.20
24.70 ~ 24.733 2.25
24.900 ~ 24.933 2.35
25.000 ~ 25.033 2.40
Notice
• Measure the crankshaft axial clearance and correct if necessary with appropriate thrust washers.
• Thrust washers of the same thickness must be installed on both sides of the fit bearing.
Matching the Crankshaft Bearing Shells to Basic Bearing Bore in Crankcase

Marking of Basic Bearing Bore in Lower Parting Surface Relevant Crankshaft Bearing Shell With Color Coding
1 punch mark or blue blue or white - blue
2 punch marks or yellow yellow or white - yellow
3 punch marks or red red or white - red
Matching Crankshaft Bearing Shells to Basic Bearing Journal of Crankshaft

Marking of Bearing journals on Crank Webs Relevant Crankshaft Bearing Shell With Color Coding
blue or white - blue blue or white - blue
yellow or white - blue yellow or white - yellow
red or white - blue red or white - red

AFFECTED VIN
DI02-35
Selection of Upper Main Bearing Shell

Punch Mark Color
• Blue
• • Yellow
• • • Red
Y220_02096
Selection of Lower Main Bearing Shell

Mark Color
B Blue
Y Yellow
R Red
W White
V Violet
Y220_02097

AFFECTED VIN
DI02-36
Crankshaft Position Sensor
Permanent
magnet
Iron
Standard coil
position
Ring gear
<Location of crankshaft position sensor> <Structure of crankshaft position sensor>

Y220_02098
The crankshaft position sensor is located near to flywheel on the rear of cylinder block. It generates AC voltage between
increment type driven plate that fixed on flywheel inside. The sensor consists of soft iron core that winded copper wire
on permanent magnet and generates sign wave AC voltage when magnetism on the sensor wheel passes the sensor.
When the crankshaft rotates, ‘+’ signal will be generated from near the front edge and ‘-’ signal will be generated from
near the rear edge among teeth on the driven plate near to crankshaft position. The AC voltage increases as the engine
speed increases, however, no signal occurs from the 2-missing-tooth on the increment type driven plate. By using these
teeth, ECU recognizes TDC of No. 1 and 5 cylinders.
ECU converts the alternative signals into digital signals to recognize crankshaft position, piston position and engine
speed. The piston position that coupled with crankshaft is main factor in calculating injection timing. By analyzing the
reference position and camshaft position sensor, can recognize No. 1 cylinder and calculate the crankshaft speed.
<Drive plate>
Y220_02099
A. Distance between ‘+’ max. voltage and ‘-’ max. a. Front edge
voltage b. Rear edge
c. 2-missing-tooth

AFFECTED VIN
DI02-37
Ground
Crankshaft position Signal

Drive plate sensor
<Circuit diagram of crankshaft position sensor>
Y220_02100
Output voltage Min. voltage: 1.0 V (40 rpm, air gap: 1.3 mm)
( 1 ~ 150 V) Max voltage: 150 V (7000 rpm, air gap: 0.3 mm)
Sensor unit coil resistance (Ω) 1,090 ± 15 %
Sensor air gap 0.3 ~ 1.5 mm

AFFECTED VIN
DI02-38
TORSIONAL VIBRATION DAMPER
Laser welding
Bearing
Cover
Hub
Bushing
Pin
Inertia ring
Silicone oil
Y220_02101
System Description
• Components: Hub, inertia mass, cover, bearing, bushing, silicon oil
• Functions: The crankshaft pulley optimizes the drive system by reducing the amount of torsional vibration in crankshaft.
Conventional rubber damper is limited in changing materials (rubbers) to absorb vibration, but this crankshaft
pulley (viscous damper), using silicon oil, takes advantage of less changing viscosity according to the
temperature.

AFFECTED VIN
DI02-39
Crankshaft - Disassembly
1. Unscrew the bolts and remove the connecting rod journal
bearing and bearing caps.
Notice
Position the #1 piston at TDC and remove the piston
connecting rod journal bearing caps.
2. Remove the bearing cap bolts.

Y220_02102
3. Remove the bearing caps.
Notice
• The crankshaft bearing caps are marked with
stamped numbers. Start to remove from the
crankshaft pulley side.
• Do not mix up the bearing shells.
4. Remove the bearing caps and lower thrust bearing.

5. Separate the lower bearing shells from the bearing caps.
Y220_02103
6. Remove the crankshaft.
Y220_02104
7. Remove the upper thrust washers.

8. Remove the upper bearing shells from the crankcase.
Notice
Do not mix up the bearing shells.
Y220_02105

AFFECTED VIN
DI02-40
Crankshaft - Reassembly
1. Thoroughly clean the oil galleries and check the journal
section and bearings. Replace if necessary.
Y220_02106
2. Coat the upper thrust washers with oil and insert into the
crankcase so that the oil grooves are facing the crank
webs (arrow).
3. Coat the lower thrust washers with oil and insert into the
crankcase so that the oil grooves are facing the crank
webs (arrow).
Notice
The retaining lugs should be positioned in the grooves

(arrow).
Y220_02107
Notice
If the maximum permissible length of L= 63.8 mm is
exceeded, the 12-sided stretch bolts should be
replaced.
Y220_02108
4. Coat the new crankshaft with engine oil and place it on

the crankcase.
5. Install the crankshaft bearing caps according to the
markings and tighten the bolts.
Tightening torque 55 ± 5 Nm + 90° + 10°
Notice
Install from #1 cap.
Y220_02109

AFFECTED VIN
DI02-41
6. Position the #1 piston at TDC and install the crankshaft.

7. Install the piston connecting rod journal to the crankshaft
journal and tighten the bolts.
8. Measure the crankshaft bearing axial clearance.
• When new: 0.100 ~ 0.245 mm
• When used: 0.300 mm
9. Rotate the crankshaft by hand and check whether it
rotates smoothly.
Y220_02110

AFFECTED VIN
DI02-42
FLYWHEEL
DUAL MASS FLYWHEEL (DMF, MANUAL TRANSMISSION EQUIPPED VEHICLE)
Primary wheel
Ring gear
Primary wheel
Secondary
wheel
Plastic bushing
Y220_02111
System Description
This flywheel is installed to the rear end of crankshaft and transfers the output from the engine to the power train
mechanism. When starting the engine, this drive the crankshaft train mechanism initially by using the power from the
start motor. Also, DMF measure the crankshaft speed, sends the signals to ECU, and controls the ignition timing.
Conventional flywheel DMF
Y220_02147

AFFECTED VIN
DI02-43
Structure
Function and characteristics
• When the output changes from the engine is high during
power stroke ( ): The damper absorbs the shocks to
reduce the changes to transmission.
• When the output changes from the engine is low during
compression stroke ( ): The damper increases the torque
changes to clutch.
<Example of DMF operation>

Y220_02112
<Torque change curve of engine and drive shaft>

Angular acceleration amplitude [1/s 2]
Conventional system DMFW
Engine
Engine
Transmission
Transmission
Speed [rpm] Speed [rpm]

Y220_02113
Function Advantages of DMF
• Filters irregularities of engine: The secondary flywheel • Improved torque response by using 3-stage type spring:
operates almost evenly so does not cause gear noises Strengthens the torque response in all ranges (low,
• The mass of the primary flywheel is less than medium, and high speed) by applying respective spring
conventional flywheel so the engine irregularity constant at each range.
increases more (less pulsation absorbing effect) • Stable revolution of the primary and secondary wheel
• Transmission protection function: Reduces the load to by using planetary gear: Works as auxiliary damper
powertrain (transmission) by blocking the irregularity against spring changes
of engine • Less heat generation due to no direct friction against
spring surface: Plastic material is covered on the spring
Characteristics of DMF outer surface
• Reduced vibration noise from the powertrain by blocking
• Increased durability by using plastic bushing (extends
the torsional vibrations
the lifetime of grease)
• Enhanced vehicle silence and riding comforts: reduced
engine torque changes
• Reduced shifting shocks
• Smooth acceleration and deceleration
AFFECTED VIN
DI02-44
PISTON AND CONNECTING ROD
Y220_02114
1. Piston 4. Oil ring

2. No.1 compression ring 5. Piston pin
3. No.2 compression ring 6. Snap ring
Description D27 DT ENG

Cylinder bore diameter φ 86.2 (0~0.018) mm
Piston outer diameter (D1) φ 86.133 (±0.009) mm
Clearance between bore and piston 74
Piston cooling gallery Applied
Pin offset N/A
Compression ratio 18 : 1
Length of piston pin 71.2 mm
Material of top ring / coating Steel / Gas nitride
Tightening torque of connecting rod bolt 40 ± 5.0 Nm, 90° + 10°
Permissible weight difference of connecting rod 4g
Thickness of connecting rod bearing (Red) 1.806 ~ 1.809 mm
Thickness of connecting rod bearing (Yellow) 1.809 ~ 1.812 mm
Thickness of connecting rod bearing (Blue) 1.812 ~ 1.815 mm

AFFECTED VIN
DI02-45
PISTON RING
1. No.1 compression ring

2. No.2 compression ring
3. Oil ring
5. Coil spring and oil control ring
6. Hook spring
Y220_02115
Replacement of Piston Ring

• Measure piston ring end play.
- Piston ring end play (mm)
1st groove: 0.20 ~ 0.35
2nd groove: 0.20 ~ 0.35
3rd groove: 0.20 ~ 0.40
- Clearance between piston ring and piston (mm)
1st compression ring: 0.075 ~ 0.119
2nd compression ring: 0.050 ~ 0.090
3rd oil ring: 0.030 ~ 0.070 Y220_02116
• Install the piston so that “Y” marking on piston head is

facing in the direction of travel. Arrange the piston ring
ends to be 120° apart.
• Adjust the hook spring joint in the oil ring 180 ° away from
the ring end.

AFFECTED VIN
DI02-46
CYLINDER INNER DIAMETER AND PISTON SIZE
Y220_02117
(Unit : mm)
Engine Code Used piston Cylinder Diameter Piston Diameter
D27DT A A or X 86.200 ~ 86.206 86.124 ~ 86.130
X A, B or X 86.206 ~ 86.212 86.129 ~ 86.137
B B or X 86.212 ~ 86.218 86.136 ~ 86.142
+5 +5 86.250 ~ 86.260 86.167 ~ 86.181
+ 10 + 10 86.300 ~ 86.310 86.217 ~ 86.231

AFFECTED VIN
DI02-47
Piston - Reassembly
1. Install the compression ring and oil ring on the piston
Y220_02118
Arrange the piston ring ends to be 120° apart.
Notice
• Install the No.1 and No.2 pistons so that “Y” marking
on piston head is facing upward.
• No.1 piston ring is thicker than No.2 piston ring.
• Arrange the oil ring end to opposite position of
current ring end.
• Oil ring is not directional.
• Make sure that the piston ring end is not aligned to
axial direction and lateral direction. Y220_02119
2. Check the clearance of piston oil ring and compression

ring with a thickness gauge and adjust if necessary.
1st groove 0.20 ~ 0.35 mm

2nd groove 0.20 ~ 0.35 mm
3rd groove 0.20 ~ 0.40 mm
* Piston ring end play (mm)

1st groove: 11.0 mm
2nd groove: 10.5 mm
3rd groove: 7.0 mm
Y220_02120
3. Check the clearance of piston rings with a thickness

gauge and adjust if necessary.
No.1 compression ring 0.075 ~ 0.119 mm

2nd compression ring 0.050 ~ 0.090 mm
3rd oil ring 0.040 ~ 0.080 mm
Y220_02121

AFFECTED VIN
DI02-48
4. Fit the piston onto connecting rod so that the marking

on piston crown and locking slot are facing to straight
ahead direction.
Notice
Install the piston so that the piston recess (marking)
or the stamped surface of connecting rod is facing to
straight ahead direction.
Y220_02122
5. Lubricate piston pin and push in by hand.
Notice
Do not heat up the piston.
6. Place new snap rings into the grooves.
Notice
The snap rings should be replaced with new one.
7. Lubricate the cylinder bore, connecting rod bearing

Y220_02123
journals, connecting rod bearing shells and pistons.
8. Push piston into the cylinder with a wooden stick.
Notice
The marking on the piston crown must be facing to

straight ahead direction.
Y220_02124
9. Insert connecting rod bearing shells.
Notice
• The upper and lower connecting rod bearings have

same appearance. Therefore, make sure to check
the part number before replacing them.
• Install bearing rod bearing cap so that so that the
retaining lugs are on the same side of the
connecting rod bearing.
Y220_02125

AFFECTED VIN
DI02-49
10. Measure stretch shaft diameter of the connecting rod

bolts.
Limit “C” 7.1 mm
Y220_02126
11. Lubricate the new connecting rod bolts and tighten.
40 ± 5.0 Nm,
Tightening torque
90° + 10°
• End play of connecting rod cap
Specified value 0.5 ~ 1.5 mm
Y220_02127
12. Position piston to TDC and measure the distance between

piston and parting surface of crankcase.
Permissible piston
0.765 ~ 1.055 mm
protrusion
• Measure at both ends of axial direction.
Y220_02128

AFFECTED VIN
DI02-50

Piston protrusion measuring jig
Y220_02129 Y220_02130
Piston insertion jig
Y220_02131 Y220_02132

AFFECTED VIN
DI02-51
HIGH PRESSURE PUMP (HPP)
COMPONENTS LOCATOR
High pressure
line
Low pressure line Venturi return line
Fuel temperature sensor
IMV connector
Inlet Metering
Valve (IMV)
High pressure
supply line
Y220_02133
1. Inlet Metering Valve (IMV) 7. Low pressure pump

2. Hydraulic pressure head 8. Fuel temperature sensor
3. Plunger 9. Venting
4. Drive shaft and cam ring 10. High fuel pressure supply line
5. Housing 11. Pressure regulator
6. Roller and shoe

AFFECTED VIN
DI02-52
HP Pump - Disassembly and Reassembly

Preceding works:
- Removal of fan belt (including cooling fan and fan clutch)
and fan shroud
- Removal of intake manifold assembly
- Removal of water pump pulley
- Removal of auto tensioner
- Removal of EGR pipe
- Removal of oil dipstic gauge
Y220_02134
Notice
• To prevent oil leaks, store the removed auto tensioner
in upright position.
• Be careful not to damage the rubber bellows.
• Plug the oil ports for HP pump with sealing caps.
1. Set crankshaft pulley to OT point. Open the oil filler cap

and check if the cam shaft notch marking is aligned to
OT point.
Y220_02135
2. Remove the cooling fan idle pulley with a pulley holder

(special tool).
Y220_02136

AFFECTED VIN
DI02-53
3. Remove the cooling fan bracket assembly.
Notice
Be careful not to get the sealant or foreign materials

into the engine.
Y220_02137
4. Place the marks on the chain and HP pump sprocket for

installation.
Y220_02138
5. Remove the vacuum modulator bracket.

6. Remvoe the fuel pipes and wiring connectors which
connected to fuel pump.
Y220_02148
7. Turn the crankshaft pulley to the counter clockwise

direction to ATDC 45° then remove the chain tensioner.
Installation Notice
Tightening torque 80 ± 8Nm
Y220_02149

AFFECTED VIN
DI02-54
8. While insert finger and push the chain guide backward

direction and turn the crankshaft pulley to ATDC 65° by
counter clockwise direction until feel the chain guide
inclined backward.
Y220_02139
9. Install a special tool into the cooling fan bracket hole to

hold the sprocket.
Y220_02140
10. Remove the sprocket bolts and center nut and after
slightly lifted up the chain, remove the pump sprocket.
Installation Notice
Sprocket bolt 20 Nm + 90°
Center nut 65 ± 5 Nm
Y220_02141
11. Remove the HP pump bearing with HP pump bearing

puller (special tool).
Notice
Do not apply excessive force. The timing chain may
deviates.
Y220_02142

AFFECTED VIN
DI02-55
12. Remove the HP pump mounting bracket.

Installation Notice
Y220_02143
13. Unscrew the external bolts and remove the HP pump

while rocking and tapping it with a rubber hammer.
Notice
• To prevent HP pump shaft damaging, do not apply

excessive impact.
• Do not apply excessive force. The timing chain may
deviates.
Y220_02144
14. Remove the HP pump.
15. Install the new HP pump with sealing caps.
Notice
Remove the sealing caps only when connecting the
pipes and hoses.
16. When replaced the HP pump, initialize the fuel pressure

by using SCAN-100. Refer to “Trouble Diagnosis” section
in this manual.
Y220_02145

AFFECTED VIN
DI02-56
Notice
If the initialization of fuel pressure has not been

performed, the engine ECU controls new HP pump
with the stored offset value. This may cause the poor
engine output.
Install in the reverse order of removal and tighten the

fasteners with the specified tightening torque.
1. HP pump sprocket
2. 12-sided sprocket mounting bolt
3. HP pump bearing housing
4. HP pump (High Pressure Pump)
5. HP pump shaft
6. HP pump center nut
7. HP pump outer bolt
8. HP pump bearing shaft
9. Oil gallery
10. Bearing bushing
11. Gasket
* Tightening torque
Y220_02146
Center nut
65 ± 5.0 Nm
(M14 x 1.5 - 1EA)
Outer bolt
24 ± 2.4 Nm
(M8 x 55 - 3EA)
Sprocket bolt
20 Nm ± 90°
(M7 x 13 - 3EA)

AFFECTED VIN
SECTION DI03
INTAKE SYSTEM
DI03-1
SECTION
00 DI03
INTAKE SYSTEM
Table of Contents
AIR FLOWS ................................................................. DI03-3
INTAKE SYSTEM LAYOUT ......................................... DI03-4

Components locator ............................................... DI03-4
Air cleaner ............................................................... DI03-5
Air flow sensor
(hot film air mass sensor) ....................................... DI03-8
Intercooler ............................................................. DI03-14
Intake manifold assembly ..................................... DI03-16
SPECIAL TOOLS AND EQUIPMENT ........................ DI03-17
INTAKE SYSTEM CHANGED BY

AFFECTED VIN
DI03-3
AIR FLOWS
Intake Valve
(in combustion chamber)
Intake Manifold
Air Cleaner
Turbo
Charger Engine
HFM Sensor
Intake Air Outlet Hose Intercooler Intake Air Inlet Hose
Y220_03001
Work Flow of Intake System

Combustion
Air HFM Turbo Intake
Intercooler Chamber in
Cleaner Sensor Charger Manifold
Engine

AFFECTED VIN
DI03-4
INTAKE SYSTEM LAYOUT
COMPONENTS LOCATOR
Air cleaner Intake manifold
HFM sensor Intercooler
Y220_03002
CHANGED BY INTAKE SYSTEM

AFFECTED VIN
DI03-5
AIR CLEANER
Cover
Element
Housing
Y220_03003
Specifications
Element Type Dry-Element Type
* Initial cleaning: 5,000 km, Clean or change every 10,000 km as required.
However, change every 30,000 km.
Service Interval
* If the vehicle is operated under severe condition (short distance driving, extensive
idling or driving in dusty condition): More frequent maintenance is required.

AFFECTED VIN
DI03-6
Air Cleaner Element - Replacement

Preceding Work: Disconnection of negative battery cable
1. Disconnect the HFM sensor connector.

2. Loosen the locking clamp and remove the intake duct.
Y220_03004
3. Unscrew the screws and remove the air cleaner cover.
Y220_03005
4. Remove the air cleaner element. Clean or replace the

element as required.
Y220_03006

AFFECTED VIN
DI03-7
Air Cleaner Housing

- Removal and Installation
Preceding Work: Removal of air cleaner cover
1. Set aside the return hose and remove the coolant reservoir
bolts.
Y220_03007
2. Remove the air cleaner housing bolts.

Y220_03008
Air Cleaner Housing/Element - Check

1. Check the air cleaner body, cover and packing for
deformation, corrosion and damage.
2. Check the air duct for damage.
Y220_03009
3. Check the air cleaner element for clogging, contamination

and damage. If the element is partially clogged, remove
the dust or foreign materials with the compressed air. If
the contamination is severe, replace it with new one. Also,
be careful not to contaminate during the replacement.
4. Check the air cleaner housing for clogging, contamination
and damage.
5. If the inside of housing is contaminated, remove the
contaminants.
Notice
When cleaning the air cleaner with compressed air,
direct the air from inside (engine) to outside (ambient
air). Otherwise, contaminants can get into the engine. Y220_03010

AFFECTED VIN
DI03-8
AIR FLOW SENSOR (HOT FILM AIR MASS SENSOR)
Change history
inner tube added + grid (No.3)
added + sensing chip changed +
sensing section design changed
Results
Durability has enhanced 60
times (lab test results)
<CI type HFM sensor structure>

Y220_03011
1. Plug-in sensor 7. Hybrid

2. Cylinder housing 8. Sensor
3. Protection grid 9. Mounting plate
4. Hybrid cover 10. O-ring
5. Measuring duct cover 11. Temperature sensor
6. Housing
Air flow sensor is locating on the air intake passage between air cleaner and intake manifold and measures air volume
flows to engine combustion chamber and intake air temperature.
And intake temperature sensor built-in the sensor detects intake temperature.
Internal circuit of the air flow sensor is being used to control the voltage value to control the temperature to maintain the
heating resistance (Rh) to 160°C that is higher temperature than intake air temperature that is measured by resistance
(RI).
Temperature sensor of the heating resistance (Rh) is measured by resistance (Rs).
If temperature changes occur due to increasing/decreasing intake air volume, voltage of the heating resistance changes
to maintain the intake air temperature changes to set value (160°C).
Control unit computes intake air volume based on voltage changes of heating resistance.
Intake air temperature is measured by NTC integrated in the sensor.

AFFECTED VIN
DI03-9
Intake air temperature sensor is a part of HFM sensor and a thermister and resister and detects air temperature
changes that flow into the engine. There occurs high resistance when temperature is low and low resistance when high
(NTC type).
ECU supplies 5 V to intake air temperature sensor and then measures voltage changes to determine the intake air
temperature. When air in the intake manifold is cold, the voltage is high and air is hot, the voltage is low.
The reason for using HFM sensor is that this sensor is most proper in controlling accurate air-fuel ratio to meet the legal
emission regulations. This sensor measures actual intake air mass into engine very accurately during specific instant
acceleration and deceleration, and determines engine loads and detects intake air pulsation and air flows.
Main functions of HFM sensor are:

• Using for EGR feedback control
• Using for turbocharger booster pressure control valve control
• Using for fuel injecting compensation
CI type HFM sensor: The air flowing the sensor does not directs toward sensing section but flows along with lower wall
after passing protection grid to enhance durability of the sensor. Oil, water and dust less damage the sensor.
Air outlet Air inlet
<Structure of CI type HFM sensor>

Y220_03012

AFFECTED VIN
DI03-10
Power supply
Intake air
flow
sensor
Ground
Ground
Signal
Intake air temperature

sensor
HFM sensor
<Circuit diagram of HFM sensor>

Y220_03013

AFFECTED VIN
DI03-11
HFM Sensor - Removal and Installation
HFM sensor
Y220_03014

2. Loosen the clamps on the air cleaner and the turbo
charger and remove the duct.
Y220_03015
3. Unscrew the bolts and remove the HFM sensor assembly.
Y220_03016

AFFECTED VIN
DI03-12
Y220_03017
Intake Air Outlet Hose (Turbo Charger)

1. Remove the radiator grille.
Y220_03018
2. Loosen the clamp at both sides and remove the outlet

hose.
Y220_03019
3. Loosen the clamp on the intake air hose and remove the
intake air hose.
Installation Notice
Notice
Securely fasten the clamps on the pipes and hoses.
Y220_03020

AFFECTED VIN
DI03-13
Intake Air Inlet Duct (Air Cleaner)

1. Loosen the clamp at intercooler side.
2. Loosen the clamp at turbo charger side.
Y220_03021
3. Separate the hose from the oil separator and remove the
intake duct.
Y220_03022
Intake Air Inlet Duct (Intake Manifold)

1. Loosen the clamp on the inlet hose in intercooler.
Y220_03023
2. Loosen the clamp at the intake manifold and remove the

inlet hose.
Installation Notice
Y220_03024

AFFECTED VIN
DI03-14
INTERCOOLER
The turbo charger is designed to improve the engine power by introducing more air (oxygen) into the engine. However,
the intake air is heated (100 ~ 110°C) during the compression process in turbo charger compressor and the density is
lowered.
The intercooler is the device which cools (50 ~ 60°C) the air entering the engine. Colder air has more oxygen molecules
than warm air. Thus cooler air gives more power and better fuel economy.
Y220_03025
1. Intercooler

AFFECTED VIN
DI03-15
Intercooler - Removal and Installation

Y220_03018
2. Loosen the clamp at both sides (inlet and outlet) of the

intercooler.
Installation Notice
Y220_03027
3. Remove the intercooler mounting bolts.

Installation Notice
Y220_03028
4. Remove the air duct in intake manifold and the intercooler

assembly.
5. Install in the reverse order of removal. Y220_03029

AFFECTED VIN
DI03-16
INTAKE MANIFOLD ASSEMBLY
Y220_03030
• Shape that delivers the required capacity of compressed air from turbo charger to inlet port
• Optimized EGR gas mixture in inlet chamber
• Maximized intake efficiency with helical and tangential inlet port
- Improving the swirl ratio in low and mid operating range
- Improving the acceleration/fuel economy and reducing the maintenance in low and mid operating range
• Integrated inlet port and coolant outlet port

AFFECTED VIN
DI03-17
SPECIAL TOOLS AND EQUIPMENT

Intake manifold locking guide pin Installation of intake manifold
Y220_03031 Y220_03032

AFFECTED VIN
DI03-18
Intake Manifold - Removal/Installation

1. Lift up the vehicle and remove the skid plate.
Y220_03033
2. Open the coolant reservoir cap and remove loosen the

drain cock to drain the coolant.
Y220_03034
3. Remove the air inlet hose (1) from intake manifold.

4. Loosen the clamp and remove the coolant inlet hose (2).
Y220_03035
5. Remove the coolant inlet port housing.

6. Remove the vacuum hose from EGR valve.
7. Remove the EGR valve mounting bolts and gasket.
Remove the EGR exhaust pipe (primary) mounting bolts
and gasket.
Notice
• Replace the pipes (2, 3) at both sides of EGR cooler

(1) and gaskets with new ones.
• Make sure that the convex surface of gasket is facing
to the pressurized direction.
Y220_03036

AFFECTED VIN
DI03-19
8. Remove the brackets and connectors from top section of

the engine.
- Vacuum hose bracket in turbo charger
- Booster pressure sensor
- Main wiring bracket
- Ground cable bracket
- Fuel pressure sensor connector
9. Unscrew the bolts and remove the vacuum modulator
bracket.
Tightening torque 9.0 Nm

Y220_03037
10. Remove the HP pump fuel supply line bolts.

11. Remove the HP pump fuel supply line mounting bracket.
12. Remove the HP pump fuel return line at fuel filter.
Notice
• Plug the openings of pipes and ports with sealing

caps to keep the cleanness of the fuel system.
• Replace the pipes with new one once removed.
Y220_03038
13. Remove the injector return line at HP pump.
Notice
• Be careful not to damage the pipes to HP pump.

• Plug the fuel return port of the HP pump with a
sealing cap.
Y220_03039

AFFECTED VIN
DI03-20
14. Remove the intake manifold mounting bolts.
Notice
1. Check the length of the bolts before installation.

M8 x 45: 6EA
M8 x 130: 6EA
Y220_03040
15. Lift up the vehicle and remove the propeller shaft joint
bolts.
16. Unscrew the bolt in oil filter and remove the intake
manifold and gasket.
Notice
• Replace the gasket with new one.
• Make sure that the residual coolant in intake
manifold gets into the inside of inlet port.
Y220_03041 17. Install in the reverse order of removal.
Notice
• Replace the gasket with new one.
• If replaced only gasket without any other service
operation, completely remove the coolant and other
contaminants from the engine before installation.

AFFECTED VIN
SECTION DI04
EXHAUST SYSTEM
DI04-1
SECTION
00 DI04
EXHAUST SYSTEM
Table of Contents
EXHAUST SYSTEM LAYOUT ..................................... DI04-3

Components locator ............................................... DI04-3
Exhaust gas flows ................................................... DI04-4
Turbo charger assembly ......................................... DI04-6
EGR VALVE AND VACUUM MODULATOR ............... DI04-27
EGR system .......................................................... DI04-27
EGR valve and turbo charger actuator
control vacuum circuit ........................................... DI04-28
EXHAUST SYSTEM AND MUFFLER ........................ DI04-36
Muffler ................................................................... DI04-36
System overview ................................................... DI04-37
EXHAUST SYSTEM CHANGED BY

AFFECTED VIN
DI04-3
EXHAUST SYSTEM LAYOUT

COMPONENTS LOCATOR
Muffler Exhaust manifold EGR valve
Catalytic converter
Turbo charger (DOC) EGR pipe Vacuum modulator
Y220_04001

AFFECTED VIN
DI04-4
EXHAUST GAS FLOWS

Catalytic converter Exhaust pipe Muffler
A
Atmo-
sphere
A Exhaust gas
Turbo charger
(turbine side)
EGR vacuum modulator
To turbo
charger booster
Turbo charger booster
vacuum modulator
Turbo charger booster EGR valve
Exhaust manifold
Blow-by gas
EGR pipe
Y220_04002
Engine
Exhaust Turbo Exhaust
-Combustion Atmosphere
Manifold Charger Muffler
Chamber-
Intake
EGR Valve
Manifold
CHANGED BY EXHAUST SYSTEM

AFFECTED VIN
DI04-5
Exhaust Manifold
1. Remove the two intake hoses from the turbo charger.
Y220_04003
2. Remove the turbo charger assembly (refer to Turbo

Charger section).
Y220_04004
3. Remove the #3 pipe of EGR valve from the exhaust

manifold.
Notice
The #3 pipe of EGR valve is exposed to the high

temperature and pressure of exhaust gas. Replace
the gasket and pipe with new ones. Otherwise, it may
cause the leakage of exhaust gas.
Y220_04005
4. Unscrew the nuts and remove the exhaust manifold and

gasket.
Notice
Replace the gasket with new one.
Y220_04006

AFFECTED VIN
DI04-6
TURBO CHARGER ASSEMBLY

The turbo charger is an air pump installed on the intake manifold. It enhances power and increases torque power of
engine to increase the fuel consumption rate. The engine without turbo charger cannot get as much power output as it
inducts air by the means of vacuum being generated from descending strokes of the piston. Therefore, by installing the
turbo charger on the intake manifold, it supplies great amounts of air to the cylinder increasing the volume efficiency
and, subsequently, enhances output power.
Also, as the engine’s power enhances, it increases the torque power and improves the fuel consumption rate. The
regular turbo charger operates by utilizing the pressure from the exhaust gas and the other, called Super Charger,
operates by utilizing power from the engine. When the turbo charger is installed, weight of the engine increases by 10
to 15 % whereas the output power increases by 35 to 45 %.
Y220_04007
Operating Principle of Turbo Charger

The turbo charger has one shaft where at each ends are in-
stalled with two turbines having different angles to connect
one end of housing to the intake manifold and the other end to
Turbine
Impeller the exhaust manifold. As the turbine, at exhaust end, is ro-
tated by exhaust gas pressure the impeller, at intake end,
Intercooler gets rotated to send air around center of the impeller, being
circumferentially accelerated by the centrifugal force, into the
diffuser.
Intake Exhaust The air, which has been introduced to the diffuser having a
passage with big surface, transforms its speed energy into
Intercooler the pressure energy while being supplied to the cylinder im-
coolant proving the volume efficiency. Also, the exhaust efficiency
Y220_04008 improves as the exhaust turbine rotates. The turbo charger is
often referred to as the exhaust turbine turbo charger.
Diffuser: With the meaning of spreading out it is a device that
transforms fluid’s speed energy into the pressure energy by
enlarging the fluid’s passage to slow down the flow.

AFFECTED VIN
DI04-7
Construction of Turbo Charger

The turbine wheel in turbo charger and compressor wheel are installed at each side of the shaft. It is comprised with the
shaft supporting center housing (supporting the compressor with two float journal bearings), the turbine side parts of
Turbine Wheel, Shroud and Turbine Housing, and the compressor side parts of compressor wheel, back plate and
compressor housing.
• The turbine rotates turbine wheel by receiving exhaust gas energy from the engine.
• The compressor receives torque energy from the turbine and the compressor wheel inducts air to force it inside of
the cylinder.
Y220_04009
1. Turbine housing A. Air inlet (from atmosphere)

2. Turbine wheel B. Exhaust gas inlet (from cylinder)
3. Compressor housing D. Exhaust gas outlet (to atmosphere)
4. Compressor wheel E. Exhaust gas bypass passage
5. Center housing H. Oil supply opening
6. Turbo charger booster pressure control valve J. Oil return line
7. Control link
8. Bypass flap

AFFECTED VIN
DI04-8
Turbine
Impeller
Impeller
The impeller is wings (wheel) installed on the intake end and
Turbine shaft performs the role of pressurizing air into the cylinder.
Thrust collar Floating bearing

Y220_04010
The radial type has the impeller plate arranged in straight line
Turbine at the center of shaft and, compared to the backward type, is
Impeller
being widely used as it is simple, easy to manufacture and
appropriate for high speed rotation. As the impeller rotates in
the housing with the diffuser installed in it, the air receives
centrifugal force to be accelerated in the direction of housing’s
Exhaust gas
outer circumference and flows into the diffuser.
As surface of the passage increases, air flown into the dif-
fuser transforms its speed energy into pressure energy and
flows into the intake manifold where the pressurized air is
Diffuser supplied to cylinder each time the intake valve of cylinder opens
Oil passage
Y220_04011
up. Therefore, the efficiency of compressor is determined by
the impeller and diffuser.
Turbine
The turbine is wings installed at the exhaust end where, by the pressure of exhaust gas, it rotates the compressor and
performs the role of transforming heat energy of exhaust gas into torque energy. The radial type is used as the turbine’s
wings. Therefore, during operation of the engine, the turbine receives temperature of exhaust gas and it rotates in high
speed, it requires to have sufficient rigidity and heat resisting property.
During operation of the engine, exhaust gas discharged through the exhaust valve of each cylinder makes turbine rotate
by coming in contact with the turbine’s wings from the outer circumference within housing of the turbine and is ex-
hausted through the exhaust manifold. At the same time, as the impeller is on the same shaft, it rotates.
Floating Bearing
Floating Bearing is a bearing, which supports the turbine shaft that rotates at about 10,000 to 15,000 rpm. It could be
rotated freely between the housing and the shaft as it gets lubricated by oil being supplied from the engine.
Notice
Stopping the engine immediately after driving at high speed stops oil from being supplied to the bearing and
may cause it to get burnt. Therefore, the engine must be stopped after cooling the turbo system by sufficiently
idling the engine.

AFFECTED VIN
DI04-9
Booster Pressure Control Valve Unit (Turbo Charger Actuator)

In order to reduce discharging of hazardous exhaust gas and to avoid the engine’s overrun the turbo charger must be
appropriately controlled. The maximum turbo charging pressure must be controlled as excessive increase in the pres-
sure and power output can cause critical damages to the engine. In order to control these, the booster pressure control
valve is installed on the turbo charger.
The difference of the booster pressure control between the existing IDI engine and DI engine is that in IDI engine, booster
pressure of the intake manifold operates the booster pressure control valve connected directly to the turbo charger
whereas in DI engine, the control is achieved by utilizing vacuum modulator (vacuum from a vacuum pump) designed to
control the booster pressure control valve. It operates booster pressure control valve by supplying electrical power to the
vacuum modulator having the amount of air being flown into the HFM sensor from the engine’s ECU as the base signal.
Refer to the EGR section in following pages for the function of turbo charger and HFM sensor in exhaust system.
Booster pressure control valve unit and vacuum modulator
Turbo charger booster Turbo charger booster

vacuum modulator
Y220_04012

AFFECTED VIN
DI04-10
Diagnosis and Maintenance for Turbo Charger System

Cautions During Driving Inspection of Turbo Charger
The following lists cautions to take during test drive and When problem occurs with the turbo charger, it could cause
on the turbo charger vehicle, which must be considered engine power decline, excessive discharge of exhaust gas,
during the operation; outbreak of abnormal noise and excessive consumption
1. It’s important not to drastically increase the engine of oil.
rpm starting the engine. It could make rotation at 1. Inspection when installed
excessive speed even before the journal bearing is - Check the bolts and nuts foe looseness or missing
lubricated and when the turbo charger rotates in poor
- Check the intake and exhaust manifold for
oil supply condition, it could cause damage of bearing
looseness or damage
seizure within few seconds.
- Check the oil supply pipe and drain pipe for
2. If the engine is running radically after replacing the
damages
engine oil or oil filter brings poor oil supply condition.
To avoid this, it’s necessary to start off after idling - Check the housing for crack and deterioration
the engine for about 1 minute allowing oil to circulate 2. Inspection of turbine in turbo charger
to the turbo charger after the replacement. Remove the exhaust pipe at the opening of the turbine
3. When the engine is stopped abruptly after driving at and check, with a lamp, the existence of interference
high speed, the turbo charger continues to rotate in of housing and wheel, oil leakage and contamination
condition where the oil pressure is at ‘0’. In such (at blade edge) of foreign materials.
condition, an oil film between the journal bearing and - Interference: In case where the oil leak sign exists,
the housing shaft journal section gets broken and even the small traces of interferences on the
this causes abrasion of the journal bearing due to the turbine wheel mean, most of times, that abrasion
rapid contact. The repeat of such condition significantly has occurred on the journal bearing. Must inspect
reduces life of the turbo charger. Therefore, the engine after overhauling the turbo charger.
should be stopped possibly in the idle condition. - Oil Leakage: Followings are the reasons for oil
leakage condition;
Notice
• Problems in engine: In case where the oil is
After string for long period of time during winter smeared on inner wall section of the exhaust
season or in the low temperature condition where gas opening.
the fluidity of engine oil declines, the engine, • Problems in turbo charger: In case where the
before being started, should be cranked to oil is smeared on only at the exhaust gas
circulate oil and must drive after checking the oil outlet section.
pressure is in normal condition by idling the
engine for few minutes. Notice
Idling for long period of time can cause oil

leakage to the turbine side due to low pressure of
exhaust gas and the rotation speed of turbine
wheel. Please note this is not a turbo charger
problem.

AFFECTED VIN
DI04-11
- Oil Drain Pipe Defect

Inspection of Turbine
In case where oil flow from the turbo charger
sensor housing to the crank case is not smooth
Thoroughly check the followings.
would become the reason for leakage as oil builds
up within the center housing. Also, oil thickens Notice
(sludge) at high temperature and becomes the
indirect reason of wheel hub section. In such case, Must absolutely not operate the turbo charger with the
clogging and damage of the oil drain pipe and the compressor outlet and inlet opened as it could damage
pressure of blow-by gas within the crank case the turbo charger or be hazardous during inspection.
must be inspected.
- Interference: In case where is trace of interference or
- Damages from Foreign Materials
smallest damage on the compressor wheel means,
When the foreign materials get into the system, most of times, that abrasion has occurred on the
it could induce inner damage as rotating balance journal bearing. Must inspect after the overhaul.
of the turbo charger gets out of alignment.
- Oil Leakage: The reason for oil leakage at the
compressor section is the air cleaner, clogged by
substances such as dust, causes the compressor
inlet negative pressure;
A. Rotating in high speed at no-load for extended
period of time can cause oil leakage to the
compressor section as oil pressure within the
center housing gets higher than pressure within
the compressor housing.
B. Overuse of engine break (especially in low gear)
in down hill makes significantly low exhaust gas
energy compared to the time where great amount
of air is required during idling conditions of the
engine. Therefore, amount of air in the
compressor inlet increases but the turbo charge
pressure is not high, which makes negative
pressure at the compressor section causing the
oil leakage within the center housing.
Notice
No problem will occur with the turbo charger if

above conditions are found in early stage but oil
leaked over long period of time will solidify at
each section causing to breakout secondary
defects.
- Damages by foreign materials: In case where the
compressor wheel is damaged by foreign materials
requires having an overhaul. At this time, it’s
necessary to check whether the foreign materials have
contaminated intake/exhaust manifold or inside of
engine.

AFFECTED VIN
DI04-12
Path of Turbo Charger Defect

The following tries to understand the defects that can occur with vehicle installed with the turbo charger and to manage
the reasons of such defects.
1. In case where oil pan/oil pipe has been contaminated, oil filter is defected and where
adhesive of gaskets has been contaminated into the oil line.
Contamination of Oil
Journal Bearing Clogging of Oil

Damage or Wear Passage
Metal Contact Poor Oil Supply
Shaft Journal Bearing Wear
Rotor Wear
Interference of
Seal Wear at Seal Wear at Intake Turbine and Com-
Exhaust System System pressor Components
Oil Leakage
Abnormal Noise Lack of Power/Poor

Acceleration (Lack of
Turbo Charged Pressure)
Check Booster Pressure

Check Exhaust Gas Pipes
Control Valve

AFFECTED VIN
DI04-13
2. Oil Pump Defect: Rapid over-loaded driving after replacing oil filter and oil and clogging of oil
line.
Poor Oil Supply
Metal Contact of Shaft /Journal Bearing/

Center Housing Inner Part
Journal Bearing/Center Housing Inner Part

Wear/Seizure
Melt down of Bearing to Turbine Wheel Journal
Rotor Rotational Movement
Seal Wear at Exhaust Seal Wear at Intake Interference of Turbine and

System System Compressor Components
Oil Leakage
Lack of Power/Poor
Abnormal Noise Acceleration (Lack of
Turbo Charged Pressure)

AFFECTED VIN
DI04-14
3. Turbine Side: Inflow of foreign materials from engine

Compressor Side: such as air filter, muffler and nut
Inflow of Foreign Materials
Inflow of Foreign Materials Inflow of Foreign Materials

into Turbine into Compressor
Compressor Wheel Blade

Shaft Wheel Blade Break
Break
Unbalancing Rotor Rotation
Rotor Bearing Wear
Rotor Turning Movement
Seal Wear at Exhaust Seal Wear at Intake Interference of Turbine and

System System Compressor Components
Oil Leakage
Lack of Power/Poor Accel-

Abnormal Noise eration (Lack of Turbo
Charged Pressure)

AFFECTED VIN
DI04-15
4. Defects caused by reasons other than that of the Turbo Charger.
Oil Leakage at Turbine
<In case where the scanner <Mechanical

displays as electrical malfunction> Malfunction>
Excessive Engine Wear Excessive Inflow of Blow-By
Gas, Idling at Low Speed,
Clogging of Oil Drain Pipe
Dampness or Poor Connec-
tion of Turbo Charger Actuator
Connecting Vacuum Circuit
Oil Leakage at Turbine Oil Leakage at Seal

Housing Entrance
Detection of DTC Code

Caused By HFM Sensor or
EGR Valve Malfunction
Misunderstanding of Oil Carbonization Caused By
Leakage High Temperature
Vacuum Modulator Power

Control Error for Controlling
No Problems in Turbo Seal Wear
Actuator in Engine ECU
Charger System
Oil Leakage
Oil Leakage at Compressor
Inflow of Dust Increase of Negative Pressure

Increase at Inlet Side
Oil Leak Sign at Compres- Excessive Inflow of Blow-By

sor Inlet and Outlet Gas, No-Load High Speed
Rotation
Misunderstanding of Oil No Problems in Turbo

Leakage Charger System

AFFECTED VIN
DI04-16
How to Diagnose
The followings are cautions to take in handling defects of turbo charger, which must be fully aware of;
Cautions When Examining the Defects:

1. After stopping the engine, check whether the bolts on pipe connecting section are loose as well as the connecting
condition of vacuum port and modulator, which is connected to the actuator.
2. During idling of the engine, check for leakage in the connecting section of pipe (hoses and pipes, duct connections,
after the turbo charger) by applying soap water. The leakage condition in the engine block and turbine housing
opening can be determined by the occurrence of abnormal noise of exhaust.
3. By running the engine at idle speed, abnormal vibration and noise can be checked. Immediately stop the engine
when abnormal vibration and noise is detected and make thorough inspection whether the turbo charger shaft
wheel has any damages as well as checking the condition of connections between pipes.
4. In case where the noise of engine is louder than usual, there is possibility of dampness in the areas related with air
cleaner and engine or engine block and turbo charger. And it could affect the smooth supply of engine oil and
discharge. 5. Check for damp condition in exhaust gas when there is sign of thermal discoloration or discharge of
carbon in connecting area of the duct.
6. When the engine rotates or in case where there is change in noise level, check for clogging of air cleaner or air
cleaner duct or if there is any significant amount of dust in the compressor housing.
7. During the inspection of center housing, inspect inside of the housing by removing the oil drain pipe to check for
sludge generation and its attachment condition at shaft area or turbine side.
8. Inspect or replace the air cleaner when the compressor wheel is damaged by inflow of foreign materials.
9. Inspect both side of the turbo charger wheel after removing inlet and outlet pipe of the turbo charger.
- Is the rotation smooth when the rotor is rotated by hand?
- Is the movement of bearing normal?
- Inspect whether there has been any signs of interference between two wheels.
Notice
It’s important not to drive the engine when the intake manifold hose has been removed.

AFFECTED VIN
DI04-17
Diagnosis and Measure
Poor Engine Power or Smoke Discharge
Air Cleaner Contamination Slack between Compres-

NO NO
and Clogging of Oil Pass sor Entrance and Exhaust Leaks at Intake Manifold
Type Air Cleaner Manifold Connection
YES YES YES
Replace Air Cleaner

Element or Oil Pass Type Inspect and Repair
Reconnect Connections
Air Filter Intake Manifold
NO
Poor Rotation or Interfer-

Leaks at Exhaust Mani- NO Leaks at Turbo Charger NO
ence of Turbo Charger
fold Connecting Flange
Components
YES YES
Inspect and Repair Intake Refer to Diagnosis

Manifold Table
NO
Clogging Between Com-

Clogging Between Air NO NO
pressor Exit and Intake Clogging of Engine Muffler
Cleaner and Compressor
Manifold
YES YES YES
Clean or Replace
Clean or Replace Affected Clean or Replace Affected
Affected Compo-
Components Components
nents
NO
Weakness of Engine
Clogging of Engine Intake/ NO Function, Intake/Exhaust
Exhaust Manifold Valve Damage, Timing
Defects of Each Valve
YES YES
Inspect and Repair Inspect and Repair

Related Components Related Components

AFFECTED VIN
DI04-18
Before Diagnosis
The base of making diagnosis on the EGR related system is the inspection on the connections of the vacuum hoses in
related system as the first priority. When abnormal condition occurs with the EGR system, the basic approach is, as
described in prior sentence, making detail inspections of vacuum circuits of each system before connecting the scan
tool or vacuum tester. It is necessary to manually check on the connections if there are any slacks or loose circuits even
if the visual inspection shows vacuum hose as being connected. If there are not any problems then the next inspection
area is the connections of the system connectors. Most problems with the occurrence of system malfunction are from
conditions of vacuum line and connector connections and the causes from the malfunction of mechanical mechanism is
actually very few.
For example, when there are no problems with basic components, let’s assume that there is a vehicle having vacuum
leak from connection slack in the vacuum line between EGR vacuum modulator and EGR valve. This vehicle, due to the
driving condition or, according to the circumstances, smog or other conditions, could create customer’s complaint and
by connecting the scanning device could display as the malfunction of the EGR valve’s potentiometer.
As previously explained, this car has a separate controller to control the Hoover EGR and, in accordance with various
input element, the controller controls EGR valve by regulating the force of vacuum being applied to the EGR valve through
PWM control. At this time, the controller has to receive feedback whether the EGR valve operates correctly according to
the value sent to the EGR modulator and this role is performed by the EGR potentiometer located at top section of the
EGR valve.
In other word, the controller sent correct output value to the EGR vacuum modulator but, due to the leakage of vacuum,
signal of required value can not be received from the EGR potentiometer causing to display as malfunction of related
parts.
As a reference, the EGR valve of diesel vehicle (DI Engine) controlling from the engine ECU to EGR system has different
shape than the Hoover EGR valve because the EGR valve’s operation signal in the DI engine is performed by the HFM
sensor instead of the EGR potentiometer.
This principle is that when the EGR valve opens up to flow exhaust gas into the intake unit the amount of fresh air,
comparatively, will be reduced. The DI engine ECU receives feedback signal of change in amount of air being passed
through the HFM sensor according to the opening amount of the EGR valve.
Hoover EGR System for IDI Engine EGR System for DI Engine
(Including the EGR Valve Potentiometer)
Y220_04013

AFFECTED VIN
DI04-19
The other big difference between the Hoover EGR and EGR controller for DI engine is that from two vacuum modulator,
one is same as being the modulator for EGR valve whereas the Hoover EGR system’s the other modulator controls
ALDA of injection pump and the DI engine’s the other modulator controls waist gate of the turbo charger.
This difference is in accordance with the difference in fuel injection method where the IDI engine has mechanical
injection system and DI engine is capable of making electronically controlled fuel injection.
In other word, to reduce the amount of the fuel injection in no-load rapid acceleration mode, the IDI engine’s Hoover EGR
utilizes solenoid valve to disconnect the connection circuit between intake manifold and ALDA causing negative pres-
sure to occur in the vacuum modulator to reduce the amount of fuel injection. When DI engine, basing input signal from
the related sensors such as acceleration pedal sensor and engine RPM, recognizes that current mode is the no-load
rapid acceleration mode it reduces the amount of fuel injection by sending short electrical signal to the injector. Therefore,
disregarding the modulator for the EGR valve in DI engine, one must keep in mind that the other modulator is used to
control the booster pressure valve in turbo charger.

AFFECTED VIN
DI04-20
When Engine Exhaust Gas shows White Smog or Blue Smog
Poor Connection between

NO Oil Leak Sign around NO Clogging of Engine Oil
Compressor Outlet and
Intake Manifold Element
Intake Manifold
YES YES YES
Reconnection Inspect PVC Line Replace Oil Filter
NO
Clogging or Damage Oil Leakage at Seal

NO NO Engine Malfunction (Ring,
between Air Cleaner and between Turbo Charger
Piston, Valve)
Turbo and Compressor
YES YES YES
Clean or Replace Affected Repair (overhaul)

Refer to Diagnosis Table
Components Engine
Excessive Consumption of Engine Oil
Poor Oil Seal at Turbo

Improper Inspection of Air NO Improper Viscosity of NO
Compressor Side (Oil leak
Cleaner Contamination Engine Oil Being Used sign at housing and wheel)
YES YES YES
Replace Air Cleaner Refer to Diagnosis

Replace with Specified Oil
Element Table
NO
Poor Oil Seal at Turbo Turbine Oil Leakage at Engine

NO
Side (trace of leakage in Exhaust Manifold (damages
housing and wheel) to ring, piston and valve)
YES YES
Refer to Diagnosis Table Inspect or repair Manifold

AFFECTED VIN
DI04-21
Abnormal Noise from Turbo Charger System
Leaks at Pipe and Hose Inflow of Foreign Material

Contamination or Clogging NO NO
Duct Parts between to Compressor Entrance
of Air Cleaner Manifolds of Turbo Charger or Housing
YES YES YES
Inspect and Repair Air

Clean or Replace If Inspect or Replace Cleaner Element and Turbo
required Connections Charger after Removing
Foreign Materials
NO
Poor Rotation of Rotating

Inflow of Foreign Materials NO Inflow of Foreign Materials NO
Turbo Charger Compo-
to Intake Manifold to Muffler
nents and Interference
YES YES YES
Inspect and Repair Air Repair Housing and

Repair Muffler and Turbo
Cleaner Element and Turbo Turbo Charger and
Charger After Removing
Charger after Removing Inspect Normal Opera-
Foreign Materials
Foreign Materials tion for Engine
NO
Check the Interference

between Rotating Turbo
Charger Components and
Housing
YES
Refer to Diagnosis Table

AFFECTED VIN
DI04-22
Poor Rotation of the Turbo Charger
Compressor Wheel Turbine Wheel Damages

NO NO Interference of Compres-
Damages By Inflow of By Inflow of Foreign
sor Wheel with Housing
Foreign Material Material
YES YES YES
Fatigue and Wear in

Repair or Replace Air
Repair or Replace Ex- Bearing or Shaft
Cleaner Element and
haust Manifold Journal (Refer to
Turbo Charger
Diagnosis Table)
NO
Excessive Deposit of
Clogging of Compressor NO Carbon or Combustion NO Gel Type Oil in Center
by Dust Residues Inside of Turbine Housing
Wheel by Oil Contamination
YES YES YES
Repair or Replace Air Repair or Replace Turbo Repair or Replace Engine

Cleaner Element and Charger Oil Filter and Turbo
Turbo Charger Charger
Oil Leakage at Turbine in Turbo Charger
Gel Type Oil in Center

Excessive Filling of Oil NO Clogging of Oil Drain NO
Housing or Excessively
When Installing Pipes in Turbo Charger
Contaminated Oil
YES YES YES
Oil Disappears After Clean or Replace Drain Repair or Replace

Combustion Line Engine Oil Filter and
Turbo Charger
NO
Poor Engine Function

Deterioration of Turbo NO
(Too High Blow-by gas
Charger Journal
pressure in crankcase)
YES YES
Refer to Diagnosis Table Inspect PVC Line

AFFECTED VIN
DI04-23
Oil Leakage at Compressor in Turbo Charger
Clogging or Damage of
Contamination of Air NO NO
Too High Oil Viscosity Pipe between Air Cleaner
Cleaner Element
and Turbo Charger
YES YES YES
Replace Damaged
Clean or Replace Air Replace With Specified
Components after
Cleaner Element Oil
Cleaning clogged Area
NO
Looseness in Connection
NO Oil Leakage at Intake NO Clogging of Oil Drain Pipe
between Compressor
Manifold in Turbo Charger System
Outlet and Intake Manifold
YES YES YES
Reconnect After Inspec- Inspect and Repair Intake Clean Clogged Area
tion Manifold After Inspection
NO
Clogging Between Com-

Deterioration or Damage NO NO
pressor Outlet and Intake Clogging of Engine Muffler
to Compressor Wheel
Manifold
YES YES YES
Clean, Repair or Replace

Air Cleaner Element and Refer to Diagnosis Table Inspect PCV Line
Turbo Charger

AFFECTED VIN
DI04-24
Wear in Turbo Charger Inner Diameter and Shaft Journal
Poor Oil Filling When

NO Contamination of Oil Filter NO Lack of Oil in Turbo
Installing or Replacing
Turbo Charger or Use of Low Grade Oil Charger
YES YES YES
Clean or Replace Air

Reinstall While Using
Cleaner Element / Re- Add Oil During Idling
Specified Oil
place With Specified Oil
NO
Poor Oil Supply by Wear in Journal Section

NO Clogging of Engine Oil NO
Clogging of Oil Supply By Clogging in Center
Pipe in Turbo Charger Filter Housing
YES YES YES
Clean and Repair Dam- Repair or Replace

Replace Oil Filter
aged Components Turbo Charger
NO
Poor Function of Engine

Oil Pump
YES
Inspect and Replace If

Required
For other diagnosis, refer to Diagnosis section.

AFFECTED VIN
DI04-25
Turbo Charger Assembly

1. Remove the drain plug and drain the engine oil from the
oil pan.
Installation Notice
Y220_04015
2. Remove the vacuum hose and inlet hose from the turbo
charger.
Installation Notice
Y220_04016
3. Remove the bolts and nuts at the exhaust manifold in

turbo charger.
Installation Notice
Y220_04017
4. Remove the lower and upper bolts at turbo charger oil

supply pipe.
Installation Notice
Y220_04018

AFFECTED VIN
DI04-26
5. Remove the lower bolts at turbo charger oil return pipe.
Notice
Replace the steel gasket with new one.
Installation Notice
Y220_04019
6. Remove the lower bolt at turbo charger bracket.

7. Remove the turbo charger bracket bolts.
Installation Notice
Notice
Use only 12 1/2" wrench.
Y220_04020
8. Remove the bolts and nuts at the turbo charger and the
exhaust manifold.
Installation Notice
Y220_04021
9. Remove the turbo charger assembly.

Notice
• Replace the steel gasket with new one.

• To prevent gas leaks, tighten the fasteners with the
specified tightening torques.
Y220_04022

AFFECTED VIN
DI04-27
EGR VALVE AND VACUUM MODULATOR

EGR SYSTEM
General Information
EGR system controls the opening vale of EGR valve by transmitting electrical signal (PWM control) from the engine
ECU to vacuum modulator. Also, the engine ECU receives the feedback signals of the amount of air flowing through the
HFM sensor.
Various sensor
Signals
Y220_04023
1. EGR valve 4. EGR center pipe (EGR cooler)

2. Vacuum modulator 5. Intake manifold
3. Vacuum pump 6. Hfm sensor

AFFECTED VIN
DI04-28
EGR VALVE AND TURBO CHARGER ACTUATOR CONTROL VACUUM

CIRCUIT
Vacuum Modulator
The biggest difference between the vacuum circuit and layout of the Hoover EGR system after K2004 has been intro-
duced is the location of the vacuum modulator for EGR valve control and the function of the other modulator. In case of
EGR equipped vehicle (IDI Engine), it performs the role of controlling the PLA of injection pump whereas, in DI engine, it
controls the turbo charger actuator.
DI engine vacuum modulator

1. EGR valve vacuum modulator
2. Turbo charger booster vacuum modulator
From vacuum pump
To EGR Valve
To turbo charger Vacuum pump

actuator
Y220_04024
IDI engine vacuum modulator (hoover EGR system - K2004)
To PLA (injection pump)
From vacuum pump
To EGR valve
From vacuum pump
Y220_04025
1. Vacuum modulator for EGR valve control 2. Vacuum modulator for injection pump PLA control

AFFECTED VIN
DI04-29
Vacuum Modulator and Vacuum Hose

Below figures illustrate vacuum hoses and related parts of EGR or turbo where wrong or poor connection of vacuum hose
would display condition of engine irregularity and defect diagnostic codes on the scan tool.
Related with EGR valve
From vacuum pump

EGR valve
Vacuum modulator for

EGR valve control
Y220_04026
Related with turbo charger actuator
Turbo charger pressure valve
Vacuum modulator for turbo From vacuum pump

charger booster control
Y220_04027

AFFECTED VIN
DI04-30
EGR System Diagram
Intercooler
Intake
manifold
Exhaust
manifold EGR
valve
Vacuum
Regulated Modulator
pump
vacuum
pressure
Duty
control
Feedback EGR Air intake signal

(Air Mass) (for EGR feed-
back control)
ECU
Improved target EGR Turbo charger
Pedal RPM
signal signal
Y220_04028
EGR Valve
EGR valve recirculates some of exhaust gases to intake system to reduce toxic NOx from engine according to ECU
signals.
• EGR valve opening point : -270 mmHg
EGR Modulator
According to ECU signals, the vacuum modulator drives EGR valve by controlling vacuum pressure that is generated by
vacuum pump with PWM type controls.

AFFECTED VIN
DI04-31
Operation Principle of Vacuum Modulator
Vacuum pump
Output vacuum
ATM
Plunger
Connector
Vacuum control
Diaphragm
Seat assembly
Atmospheric pressure Spring
Plunger
Air flow
During duty increase (B) During duty reduction (C)
Vacuum is controlled according to relationship between chamber pressure (I) in rolling nipple cover and magnetic
force (II) in plunger.
Y220_04029
According to ECU signals, the solenoid valve controls the vacuum pressure that is generated by vacuum pump (-900 ±
20 mbar) with PWM type control and drives the mechanical EGR valve and turbo charger.

AFFECTED VIN
DI04-32
Operating principle: Balance between original vacuum pressure and magnetic force (see above figure)
• Normal state (Fig. A): Original vacuum and seat section, 3 stoppers keep sealing
• Duty up state (Fig. B): Original vacuum pressure is connected to inside of diaphragm chamber
• Duty down state (Fig. C): Increased diaphragm chamber pressure is connected to atmosphere to compensate the
pressure.
Floating plunger Stroke

(mm)
Max. Distance 1mm
DUTY 50%
Output C/V
Y220_04030
Operating principles when duty is applied from 0 to 50 %
Vacuum consumption: Compared to 50 % of duty, ON/OFF periods are most unstable and vacuum
consumption is most high.
Flowing
volume
Y220_04031
Output Characteristics
Output vacuum (-mmHg)
Up
Down
Y220_04032

AFFECTED VIN
DI04-33
Operating Conditions
• Engine is running
• Engine RPM is within a specified range. (EGR OFF under high RPM range)
• Engine torque is within a specified range. (EGR OFF under high torque range)
• Vehicle speed is within a specified range. (EGR OFF under high speed range)
• Atmospheric pressure is within a specified range. (EGR OFF under high altitude and low atmospheric pressure)
• Coolant temperature is within a specified range. (EGR OFF under high or low temperature)
• EGR OFF under extended period of idling.
Control Logic
• Main map: EGR volume is controlled based on intake air volume
• Auxiliary map
- Coolant temperature (Coolant temperature sensor)
- Engine rpm (Crankshaft position sensor)
- Engine load (TPS): Detection of sharp acceleration
- Intake air temperature (HFM): Decreases when over 60°C
- Atmospheric pressure (Barometric sensor): Compensation of altitude
• Compensation value of auxiliary map will be increased/decreased based on main map then ECU calculates EGR
volume finally to regulate the vacuum duty that applies to the vacuum modulator to control EGR valve openings.
Shut-off Conditions
• Engine rpm: over 2,950 rpm
• Vehicle speed: over 105 km/h
• Coolant temperature: over 100°C or below 10°C
• Idle period: over 50 seconds

AFFECTED VIN
DI04-34
EGR Valve and Pipe

1. Remove the vacuum hose from the EGR valve.
Y220_04033
2. Unscrew the bolts and remove the EGR valve (2), EGR
valve #1 pipe (1) and gasket.
Y220_04034
3. Remove the EGR valve #1 pipe, #2 pipe, #3 pipe and

gaskets from the engine.
Y220_04035
EGR #3 pipe (LH) Notice

EGR #1 pipe (RH)
• Make sure to observe the specified tightening
EGR center pipe torques.
• Never reuse the EGR #1 pipe (intake) and #3 pipe
(exhaust) once removed.
• Replace the gaskets with new ones.
Y220_04036

AFFECTED VIN
DI04-35
Vacuum Modulator
1. Remove the vacuum hose from the vacuum modulator.
Y220_04037
2. Remove the vacuum modulator from the bracket.
Notice
Make sure that the vacuum hoses are connected to
correct locations.
Y220_04038

AFFECTED VIN
DI04-36
EXHAUST SYSTEM AND MUFFLER
(1) #1 Pipe (turbo charger side) (2) DOC (Diesel Oxidation Catalyst)
(3) Muffler Hanger Muffler (4) Tail pipe
Y220_04039
MUFFLER
The muffler is located at the middle of the exhaust pipe and reduces the pulse noise and the tail pipe noise by eliminating
the flowing resistance from the exhaust gas.
The important elements of the muffler are volume, construction and location.

AFFECTED VIN
DI04-37
SYSTEM OVERVIEW
Exhaust System Muffler
Check the complete exhaust system and the nearby body Aside from the exhaust manifold connection, the exhaust
areas and trunk lid for broken, damaged, missing or system uses a flange and seal joint design rather than a
mispositioned parts, open seams, holes, loose slip joint coupling design with clamp and U-bolts. If hole,
connections, or other deterioration which could permit open seams, or any deterioration is discovered upon in-
exhaust fumes to seep into the trunk may be an indication spection of the front muffler and pipe assembly, the com-
of a problem in one of these areas. Any defects should be plete assembly should be replace, the complete assem-
corrected immediately. bly should be replaced. The same procedure is applicable
to the rear muffler assembly. Heat shields for the front and
Notice rear muffler assembly and catalytic converter protect the
vehicle and the environment from the high temperatures
When you are inspecting or replacing exhaust system that the exhaust system develops.
components, make sure there is adequate clearance
from all points on the underbody to avoid possible
overheating of the floor panel and possible damage to
the passenger compartment insulation and trim
Heat Shield
materials. The heat shield protects the vehicle and components from
the high heat generated from the exhaust system.
In this vehicle, the heat shield to block the heat from DOC
DOC (Diesel Oxidation Catalyst) is installed to the underbody, and the heat shield to block
the heat from the rear muffler is installed to the underbody
DOC (Diesel Oxidation Catalyst) is the purification device between the fuel tank and the rear muffler.
to reduce the toxic emissions from the exhaust gas from
the engine. By using the chemical reaction, the amount of
toxic gas such as NOx can be reduced.
Hanger
Notice The hanger is to support the components.
If the ganger is not properly installed, it may cause the
To prevent damage of DOC, never contact the lift pad
vibration that is very difficult to diagnose. Therefore, install
when lifting up the vehicle.
the hanger to the correct location so that the exhaust sys-
tem cannot contact to the underbody and other
components.

AFFECTED VIN
DI04-38
DOC (Diesel Oxidation Catalyst)

System and principle Catalytic converter structure
Oxidation catalytic technology for diesel engine is basi- The Catalytic converter of monolith type consists of 2 walled
cally the same with it of gasoline engine used before de- metal bodies which is made of Cordierite.
velopment of 3 primary catalyst (2 primary catalyst), and The principal element of converter consists of the materi-
its effect and performance were already proved. als like Alumina or oxidized Serume in order to apply to
DOC (Diesel Oxidation Catalyst) reduces HO and CO con- Ceramic Monolith. Washer coat operates first, and cata-
tained exhaust gas over 80 %, and removes SOF (Soluble lytic metal elements (Pt, Pd, Ph) operates to washer coat
Organic Fraction) over 50 ~ 80 %, but because its portion next.
in total PM is low, it reduces approx, 20 ~ 40 % of TPM Monolith type is lighter than other types, easy to manu-
(Total Particulate Material). facture and quickly approaches to proper temperature.
Because of low reducing rate for PM of DOC, in order to Washer coat is used to make a contact surface with ex-
guarantee safety rate of PM regulation, this technology is haust gas bigger by adhering closely to small holes of
being used mainly. And it should keep over 80% of PM inner layer.
reducing rate, and at present it plays a role as a transition
If a lead compound or phosphorus adheres to the surface
stage.
and the temperature rises, its surface is decreased.
And also it reduces diesel odor and black smoke, plati-
The total area of general monolith converter is about
num or palladium are being used as a catalyst.
45,000 ~ 500,000 ft 3. (10 times of a football field)
On the other hand, it is a problem that it makes the reac-
Generally Alumina (AL2O3) is used as a raw material and
tion of oxidation, which SO2 produce SO3 and H2 SO4 by
its 7 phases of gamma, delta, theta have big areas and
reacting to oxygen in exhaust gas, if temperature of ex-
high stability for the temperature, and nowadays gamma
haust gas becomes over 300°C, and this produced gas is
Alumina is used usually.
very harmful to human body. To prevent is, previously it is
requested that the sulfur content rate of fuel should be
below 0.05 %, and in the future it is being expected to
keep it below 0.01 %. Cover
Insulation Upper part of
Mat converter
Plate
Lower part of Monolith catalyst

converter
Inlet gas Outlet gas
Y220_04040

AFFECTED VIN
DI04-39
Catalytic converter and temperature

Catalytic converter has the normal function of purification at a
range of the temperature. Because it has a weak point of de-
creasing of the purification rate in the condition of continuous
high temperature, it should keep the temperature range of 400
to 500°C for normal condition. HC purification rate becomes
better according to the increase of temperature in the normal
range of temperature. CO purification rate becomes the best
near the temperature of 450°C, and NOx does so near the
temperature of 400 to 500°C.
Purification of catalytic converter

• Adhesion of soluble organic fraction (SOF) below 180°C
• Purification of soluble organic fraction (SOF) over 180°C
Chemical reaction formula
• SOF(HC) + O2 ............... O2 + H2O
• 2CO + O2 ...................... 2CO2
• 2C2H6 + 7O2 ................. 4CO2 + 6H2O
Y220_04041
Aldehide
Aromatic HC
Y220_04042
• Oxygen adheres to catalytic material : below 180°C
Catalytic Material
Catalytic Material
Y220_04043

AFFECTED VIN
DI04-40
• Catalytic material supplies each CO and HC with O2 for

their oxidation : above 180°C
Catalytic Material Catalytic Material
Y220_04044
• Catalytic material conversion process by DOC

PAH (Aromatic HC)
Catalyzer
Y220_04045
Method for reduction of NOx

NOx is generated a great deal in case that combustion tem-
perature and excess air factor are high. EGR valve can de-
crease NOx (30 to 35 % decrease) by making temperature of
combustion chamber fall by means of exhaust gas re-
circulation.

AFFECTED VIN
DI04-41
#1 Exhaust Pipe
1. Remove the upper bolts at turbo charger.
Notice
Use the universal type wrench.
Y220_04046
2. Remove the lower bolts and gasket.
Y220_04047
3. Remove the pipe mounting rubber.
Y220_04048
4. Remove the #1 exhaust pipe.

Y220_04049

AFFECTED VIN
DI04-42
Catalytic Converter
1. Unscrew the bolts at both sides and remove the gasket
and the converter.
Y220_04050
#2 Exhaust Pipe
1. Unscrew the bolts and remove the gasket.
Y220_04051
2. Release the rear mounting lever with a screwdriver.
Y220_04052
3. Remove the #2 exhaust pipe.
Y220_04053

AFFECTED VIN
SECTION DI05
LUBRICATION SYSTEM
DI05-1
SECTION
00 DI05
LUBRICATION SYSTEM
Table of Contents
LUBRICATION SYSTEM ............................................. DI05-3

Lubrication system layout ....................................... DI05-4
Lubrication diagram ................................................ DI05-5
Specifications .......................................................... DI05-6
Engine oil change ................................................. DI05-10
Oil pump ................................................................ DI05-14
Oil spray nozzle ..................................................... DI05-16
Oil pan assembly .................................................. DI05-17
TROUBLE DIAGNOSIS ............................................. DI05-18
LUBRICATION SYSTEM CHANGED BY

AFFECTED VIN
DI05-3
LUBRICATION SYSTEM
Cylinder head cover Oil dipstick Oil separator Oil filter
Oil pump Oil pan Oil cooler Oil pressure switch
Y220_05001

AFFECTED VIN
DI05-4
LUBRICATION SYSTEM LAYOUT
Main oil gallery: φ 16

Hole to cylinder head: φ 9
Main bearing hole: φ 7
Chain and injection pump: φ 7
Cylinder head Return hole: φ 14
Chain nozzle: φ 1
HP pump bearing: φ 6
Cylinder block
Y220_05002
CHANGED BY LUBRICATION SYSTEM

AFFECTED VIN
DI05-5
LUBRICATION DIAGRAM
Chain lubrication REF-Roller Camshaft bearing Vacuum pump
Oil tensioner
check valve
Return check valve

to cylinder head Oil injection nozzle Turbo charger
Thrust bearing Connecting rod bearing Main bearing
Filter by-pass valve
Oil
filter
By-pass throttle
Contaminated oil Clean oil gallery

gallery
Oil pump Relief valve
Oil cooler
Fuel tank
Y220_05003
1. Opening pressure of by-pass valve in oil filter: 3 ± 0.4 bar

2. To prevent instant oil shortage after stopping the engine, the return check valve is installed in oil supply line of
cylinder head.

AFFECTED VIN
DI05-6
SPECIFICATIONS
Engine oil Specification Approved by MB Sheet 229.1 or 229.3
Viscosity: See MB Sheet 224.1
Capacity 6.8 ~ 8.3 liter
Service interval Initial change: 5,000 km, Change every 10,000 km or
12 months (Frequently check the oil level and add if needed.
And, every 5,000 km or 6 months under severe conditions)
Engine oil filter Same interval with engine oil
Oil relief valve opening pressure 5.8 ± 0.3 bar
Severe condition:
- When most trips include extended idling and/or frequent low-speed operation as in stop-and-go traffic.
- When most trips are less than 6 km (Operating when outside temperatures remain below freezing and when most
trips are less than 16 km)
- When operating in dusty, sandy and salty areas
- In hilly or moutainous terrain
- When doing frequent trailer towing
Oil Pressure Switch

• Operating temperature: -40 ~ 140°C
• Operating pressure: 0.3 ~ 0.55 bar
• Permissible pressure: 10 bar
Y220_05004

AFFECTED VIN
DI05-7
Oil Pump
Y220_05005
Engine Oil Relief Valve Opening Pressure

MB SHEET
D27DT 229.1/3 5.8 ± 0.3 bar
SAE 10W 40, 5W 40
Differences between D27DT and old model (D29ST)

- Enlarged pump capacity: Width of tooth (pump gear): 33 mm (D29ST: 30 mm)
- Increased number of teeth (sprocket): 26 (D29ST: 24)
Oil Cooler
• Oil cooler mounting bolt: M6 x 16: 4
• Replace two oil cooler gaskets with new ones when the
oil cooler has been removed.
Y220_05006

AFFECTED VIN
DI05-8
Blow-by Gas Reduction Device
Oil dipstick tube
PCV valve + oil

separator
to air duct
hose
Y220_05007
Cylinder Head Cover
Blow-by gas inlet port Baffle plate
U-type oil
drain pipe
Y220_05008
Baffle plate assembly: The baffle plates in cylinder head cover separates oil and gas from blow-by gas, and controls the
blow-by gas speed to send only gas to separator.

AFFECTED VIN
DI05-9
Oil Separator
PCV valve
Outlet port (gas only)
(connected to air duct hose)
Inlet port (oil + gas)

(connected to cylinder head cover
through blow-by hose)
Oil separator
Oil drain (oil only)

(connected to oil pan through oil dipstick tube)
Y220_05009
The first separation will happen when blow-by gas passes through baffle plates in cylinder head cover; then oil and gas
will be separated due to cyclone effect after entering the oil separator inlet port. Separated oil returns to oil pan via oil
drain port and the gas will be burnt again after entering the combustion chamber through air duct hose via PCV valve that
opens/closes due to pressure differences between the intake side and crankcase.
Engine Oil Pressure Check

Check the oil level and quality before checking the oil pressure.
1. Drain the engine oil.
2. Disconnect the oil pressure switch connector and remove the switch.
3. Install the oil pressure gauge into the switch hole. Start the engine and let it run until the coolant temperature
reaches at normal operating temperature (80 ~ 90°C).
4. Raise the engine speed by 2000 rpm and measure the engine oil pressure.
Specified oil pressure 2.5 ~ 3.0 kg/cm2(2000 RPM)
5. Install the switch and engage the connector.
Notice
• Apply the Loctite onto the thread of the switch and

check for oil leaks.
Tightening torque 120 ~ 160 kg/cm2

AFFECTED VIN
DI05-10
ENGINE OIL CHANGE

Change interval: Initial change: 5,000 km, Change every 10,000 km or 12 months
Frequently check and add if needed. Shorten the change interval under severe conditions.
* Severe condition:
- When most trips include extended idling and/or frequent low-speed operation as in stop-and-go traffic.
- When most trips are less than 6 km (Operating when outside temperatures remain below freezing and
when most trips are less than 16 km)
- When operating in dusty, sandy and salty areas
- In hilly or moutainous terrain
- When doing frequent trailer towing
Notice
Water separation from the fuel filter should be performed when changing the engine oil.
Engine Oil Changing Procedures

1. Park the vehicle on the level ground and warm up the
engine until it reaches normal operating temperature.
2. Stop the engine and wait around 5 minutes. Remove the
oil filler cap, oil filter and oil drain plug to drain the oil.
Notice
After driving, the engine oil temperature may be high
enough to burn you. Wait until the oil is cooled down.
3. Install new oil filter and tighten the drain plug with specified
Y220_05010 tighten torque.
Oil drain plug 25 ± 2.5 Nm
Notice
• Over-tightening may cause oil leaks.
• Replace the drain plug washer with new one.
4. Fill the engine oil through the oil filler opening.
Notice
The oil should not go above the upper mark on the dipstick. This would lead, for example, to increased oil
consumption, fouling of the spark plugs and excessive formation of carbon residue.
5. Close the oil filler cap and start the engine.

6. Stop the engine again and check the oil level. Add the engine oil if needed and check for the oil leaks.

AFFECTED VIN
DI05-11
Engine oil filter change

1. For changing procedures, refer to the “Lubrication System” section in this manual.
• Lubricate the engine oil gasket with engine oil before installation.
• Tighten it with the specified tightening torque.
Oil filter 25 ± 2.5 Nm
Y220_05011

AFFECTED VIN
DI05-12
Oil Filter and Cooler

Preceding Works:
- Draining of engine oil
- Removal of EGR vacuum modulator bracket
1. Remove the oil cooler hoses (supply and return lines).
Y220_05012
2. Disconnect the ground cable from the oil pressure switch.
Y220_05013
3. Remove the oil cooler and filter mounting bolt.
Notice
Pay attention to the length of bolts.
Y220_05014
4. Remove the oil cooler and filter assembly from the cylinder
block.
Notice
The oil cooler and filter assembly cannot be replaced

separately.
Y220_05015

AFFECTED VIN
DI05-13
Y220_05016

AFFECTED VIN
DI05-14
OIL PUMP
Y220_05017
1. Oil pump 5. Screw plug ...................................................... 50 Nm

2. Plunger 6. Combination bolt ................................... 23 ± 2.3 Nm
3. Compression spring 7. Oil strainer
4. Guide pin
Oil Pump - Removal and Installation

1. Remove the oil pan.
M6 x 20 (24 EA) 10 ± 1.0
M6 x 35 (2 EA) 10 ± 1.0
M6 x 85 (2 EA) 10 ± 1.0
M8 x 40 (4 EA) 25 ± 2.5
Y220_05018
2. Remove the oil pump.

3. Remove the screw plugs and the relief valve.
5. Start the engine and check for oil leaks.
Y220_05019

AFFECTED VIN
DI05-15
Oil Dipstick Guide Tube

1. Pull out the engine oil dipstick.
2. Remove the EGR valve pipe (No.3).
Notice
Replace the pipe with new one.

Y220_05020
3. Unscrew the bolt and remove the oil dipstick guide tube.
Notice
Replace the O-ring with new one.
Notice
After installation, check for oil leaks.

AFFECTED VIN
DI05-16
OIL SPRAY NOZZLE
Y220_05021
1. Fitting sleeve 3. Combination bolt .............................................. 10 Nm

2. Oil spray nozzle 4. Oil duct
Disassembly
1. Remove the oil pan or crankshaft.
2. Unscrew the bolts and remove the nozzle.
Y220_05022

AFFECTED VIN
DI05-17
OIL PAN ASSEMBLY
Y220_05023
1. Oil pump 44. Bolt ................................................................... 10 Nm

9. Oil pump cover 45. Washer
10. Bolt 46. Bolt
32. Drain plug 49. Oil pump roller chain
33. Drain plug .............. 25 ± 2.5 Nm(replace the washer) 50. Oil pump chain lock link
35. Spring pin 51. Oil pump chain tensioner
36. Oil pump drive shaft 52. Oil pump chain spring
37. Oil pump driven shaft 53. Bush
38. Oil pump relief valve piston 56. Oil pump sprocket
39. Spring 57. Bolt
40. Oil pump relief valve pin 58. Dust cover
41. Oil pump relief valve plug 59. Cylindrical pin

AFFECTED VIN
DI05-18
TROUBLE DIAGNOSIS
Symptom Cause Action

• Loosened oil drain plug • Retighten
• Loosen oil pan bolts • Retighten
• Poor sealing at oil pan gasket • Replace
• Loosened oil filter • Retighten
• Loosened oil pressure switch • Retighten
• Poor sealing at camshaft front oil seal • Replace
• Poor sealing at crankshaft front oil seal • Replace
• Poor sealing at crankshaft rear oil seal • Replace
Excessive oil
• Poor sealing at cylinder head cover gasket • Replace
consumption
• Damaged cylinder head cover gasket • Replace
Oil intrusion into combustion chamber
• Stuck piston ring • Remove carbon or replace ring
• Worn piston or cylinder • Boring or replace
• Worn piston ring or ring groove • Replace piston and piston ring
• Improper position of ring cut-outs • Adjust
• Worn or damaged valve mechanism • Replace
• Oil leaks • Repair
• Defective turbo charger • Check
Defective lubrication system
• Improper viscosity • Replace with specified oil
• Loosened oil pressure switch • Retighten
Low engine oil • Low engine oil level • Add
pressure
• Poor oil pump • Replace
• Worn or damaged oil pump relief valve • Replace
• Clogged oil filter or oil strainer • Replace or clean
• Oil leaks • Repair

AFFECTED VIN
DI05-19
103 589 02 09 00
Engine filter cap
Y220_05024

AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SECTION DI06
COOLING SYSTEM
DI06-1
SECTION
00 DI06
COOLING SYSTEM
Table of Contents
COOLING SYSTEM .................................................... DI06-3
ENGINE COOLING SYSTEM ...................................... DI06-4

Specifications ........................................................ DI06-10
INSPECTION AND REPAIR ....................................... DI06-14
Inspection .............................................................. DI06-14
REMOVAL AND INSTALLATION ............................... DI06-16
PREHEATING SYSTEM ............................................ DI06-29

Overview ............................................................... DI06-30
Preheating relay ................................................... DI06-30
Preheating system diagram .................................. DI06-31
COOLING SYSTEM CHANGED BY

AFFECTED VIN
DI06-3
COOLING SYSTEM
Coolant temperature
Coolant reservoir FFH
sensor
Radiator Water pump Cooling fan
Y220_06001
FFH (Fuel Fired Heater): refer to “FFH System” in this manual.

AFFECTED VIN
DI06-4
ENGINE COOLING SYSTEM
Coolant
reservoir
Engine
Cylinder head
Thermostat
Heater
Radiator
Water pump
Cylinder block
Oil cooler
(Heater line)
<PTC Engine Coolant Flows>
Coolant
reservoir
Engine
Cylinder head
Thermostat
Heater
Radiator
Water pump
Cylinder block
EGR cooler
Oil cooler
(henceforth)
<FFH Engine Coolant Flows>

Y220_06002
• Cylinder block side

Block #5 → Oil cooler → Heater → Heater water pump inlet pipe → Water pump
• Cylinder head side
Cylinder head → Coolant outlet port (intake #1) → Radiator → Water pump
CHANGED BY COOLING SYSTEM

AFFECTED VIN
DI06-5
Function Description
Intake Manifold
Cylinder Head
Coolant Outlet Port
Y220_06003
• Cylinder head coolant outlet port is integrated into intake manifold. (in front of cylinder #1)
: Improved shape and gasket material to prevent coolant from leaking
From cylinder head

From reservoir
4
5
6
From heater
1 2 3
Y220_06004
• In OM 600 engine, coolant inflows through the heater line rear section (cylinder #4 and #5) of cylinder head. However,
in D27DT engine, coolant inflows from cylinder block through oil cooler (refer to coolant flows layout in previous
page).
: It prevents cooling efficiency from decreasing due to coolant separation between cylinder #4 and #5.
• In OM 600 engine, the cooling fan is installed with water pump, however, in case of D27DT engine, it is connected to
water pump with an additional pulley.

AFFECTED VIN
DI06-6
Radiator
This vehicle has a lightweight tube-and-fin aluminum radiator.
Be careful not to damage the radiator core when servicing.
Y220_06005
Water pump
The belt-driven centrifugal water pump consists of an impeller,
a drive shaft, and a belt pulley. The impeller is supported by a
completely sealed bearing.
The water pump is serviced as an assembly and, therefore,
cannot be disassembled.
Y220_06006
Coolant reservoir
Notice
Scalding hot coolant and steam could be blown out under

pressure, which could cause serious injury. Never remove
the coolant reservoir cap when the engine and radiator
are hot.
The coolant reservoir is a transparent plastic reservoir, similar

to the windshield washer reservoir. The coolant reservoir is
connected to the radiator by a hose and to the engine cooling
Y220_06007
system by another hose. As the vehicle is driven, the engine
coolant heats and expands. The portion of the engine coolant
displaced by this expansion flows from the radiator and the
engine into the coolant reservoir. The air trapped in the radia-
tor and the engine is degassed into the coolant reservoir.
When the engine stops, the engine coolant cools and
contracts. The displaced engine coolant is then drawn back
into the radiator and the engine. This keeps the radiator filled
with the coolant to the desired level at all times and increases
the cooling efficiency. Maintain the coolant level between the
MIN and MAX marks on the coolant reservoir when the sys-
tem is cold.

AFFECTED VIN
DI06-7
Thermostat
A wax pellet-type thermostat controls the flow of the engine
coolant through the engine cooling system. The thermostat is
mounted in the thermostat housing to the front of the cylinder
head. The thermostat stops the flow of the engine coolant
from the engine to the radiator to provide faster warm-up, and
to regulate the coolant temperature. The thermostat remains
closed while the engine coolant is cold, preventing circulation
of the engine coolant through the radiator. At this point, the
engine coolant is allowed to circulate only throughout the heater
core to warm it quickly and evenly. As the engine warms, the
thermostat opens. This allows the engine coolant to flow Y220_06008
through the radiator where the heat is dissipated. This open-

ing and closing of the thermostat permits enough engine cool-
ant to enter the radiator to keep the engine within proper en-
gine temperature operating limits. The wax pellet in the ther-
mostat is hermetically sealed in a metal case. The wax ele-
ment of the thermostat expands when it is heated and con-
tracts when it is cooled. As the vehicle is driven and the en-
gine warms, the engine coolant temperature increases. When
the engine coolant reaches a specified temperature, the wax
pellet element in the thermostat expands and exerts pressure
against the metal case, forcing the valve open. This allows the
engine coolant to flow through the engine cooling system and
cool the engine. As the wax pellet cools, the contraction al-
lows a spring to close the valve.
The thermostat begins to open at 85°C and is fully open at
100°C. The thermostat closes at 85°C.
Operating
Thermostat Opening Value (mm)
Temperature (°C)
Begins to open 85°C 0.1 mm
Fully open 100°C 8 mm

AFFECTED VIN
DI06-8
When closed (up to 85°C) When partially opened (85°C ~ 100°C)
Y220_06009 Y220_06010
X. from vrankcase
Y. to crankcase
Z. from radiator
When fully opened (above 100°C)

If the cooling system is fully filled with, the coolant is auto-
matically bled through ball valve (arrow) in thermostat.
Y220_06011 Y220_06012

AFFECTED VIN
DI06-9
Viscous fan clutch
Y220_06014
The cooling fans are mounted behind the radiator in the

engine compartment. The electric cooling fans increase
the flow of air across the radiator fins and across the con-
denser on air conditioner. The fan is 320 mm in diameter
with five blades to aid the airflow through the radiator and
the condenser. An electric motor attached to the radiator
support drives the fan.
1. A/C Off or Non-AC Model
Y220_06013
• The cooling fan operates at low speed when the
1. Clutch housing 9. Pin coolant temperature reaches 95°C and at high
2. Drive disc 10. Bi-metal speed when the coolant temperature reaches
3. Flange 11. Bracket cover 100°C.
4. Seal ring 12. Separator disc • The cooling fan is turned from high speed to low
speed at 97°C and turns off at 90°C.
5. Needle bearing 13. Supply port
6. Cooling fan 14. Lever valve
2. A/C On
7. Oil scraper 15. Oil chamber
• The ECU will turn the cooling fan on at high speed
8. Spring 16. Operating chamber when the A/C system is on.
The cooling speed increases approx. 1,000 rpm with wind Engine coolant temperature sensor
noise when the engine speed is 4,000 to 4,500 rpm and
The Engine Coolant Temperature (ECT) sensor uses a tem-
the coolant temperature is 90 to 95°C.
perature to control the signal voltage to the Engine Control
Unit (ECU).
Notice
Keep hands, tools, and clothing away from the engine
cooling fans to help prevent personal injury. This fan
is electric and can turn on even when the engine is
not running.
Notice
If a fan blade is bent or damaged in any way, no attempt

should be made to repair or reuse the damaged part.
A bent or damaged fan assembly should always be
replaced with a new one to prevent possible injury.
Y220_06015

AFFECTED VIN
DI06-10
SPECIFICATIONS
Description Unit Specification
Cooling system Type - Water cooling forced circulation
Coolant Capacity 11.3
Thermostat Type - Wax pellet type
Initial opening temperature DI Engine °C 85
IDI Engine °C 80
Fully opening temperature DI Engine °C 100
IDI Engine °C 95
Fully closing temperature DI Engine °C 83
IDI Engine °C 78
Stroke DI Engine mm min. 8
IDI Engine mm min. 8
Cooling fan Type - Electric
Blades 5
Diameter mm 320 (2)
Low speed ON temp °C 91
Low speed OFF temp °C 88
High speed ON temp °C 95
High speed OFF temp °C 92
High speed ON temp. (By A/C pressure) psi 270
Coolant reservoir pressure valve opening pressure Kg/cm2 1.2 ~ 1.5
Vacuum valve opening pressure Kg/cm2 0.1
Water pump Type - Turbo centrifugal
Impeller diameter mm 72.3
Impeller blades 10
Radiator Type - Down-flow
Core width mm 701
Core height mm 372
Core thickness mm 18
Minimum radiation capability Kcal/h 45,000
Coolant tempera- Resistance (at 20°C) KΩ 3.33 ~ 3.78
ture sensor Resistance (at 80°C) KΩ 0.32 ~ 0.35
Anti-freeze agent Type − ALUTEC-P78
Mixture ratio (water and anti-freeze) − 50 : 50

AFFECTED VIN
DI06-11
Coolant Level Check
Notice
• Scalding hot coolant and steam could be blown out under pressure, which could cause serious injury. Never
remove the coolant reservoir cap when the engine and radiator are hot.
• Take precautions to prevent antifreeze coming in contact with the skin, eyes or vehicle body. If contact
happens, rinse affected areas immediately with plenty of water.
1. Place the vehicle on a level ground and check the coolant level through the coolant reservoir.
2. Add if needed. Change the coolant if necessary.
Y220_06016

AFFECTED VIN
DI06-12
Coolant Temperature Sensor
Temp.
Resistance
<Coolant Temperature Sensor> <Output Characteristics of Coolant Temperature Sensor>
Y220_06017
Coolant temperature sensor is a NTC resister that sends coolant temperature to ECU.
NTC resister has characteristics that if the engine temperature rises, the resistance lowers so the ECU detects lowering
signal voltages.
If the fuel injected into the engine through injector has more turbulence, then combusts very well. However, if engine tempera-
ture is too low, the fuel injected as foggy state forms big compounds causing incomplete combustion. So the sensor detects
coolant temperature and changes coolant temperature changes into voltage then sends to ECU to increase the fuel volume
during cold start for better starting. And detects engine overheating for fuel volume reduction to protect the engine.
ECU functions as below with coolant temperature sensor signals.
• When engine is cold, controls fuel volume to correct idle speed
• When engine is overheated, controls electrical fan and A/C compressor to protect the engine
• Sends information for emission control
Temperature NTC 1 Resistance ( Ω ) NTC 2 Resistance ( Ω )

20 2,550 6,062
50 826 1,800
80 321 638
120 123 200
Signal
Auto amp
Ground
<Coolant Temperature Sensor Circuit> Y220_06018

AFFECTED VIN
DI06-13
Trouble Diagnosis
Low coolant • Leaks in radiator • Replace radiator
level • Leaks in coolant reservoir • Replace coolant reservoir
• Leaks in heater core • Replace heater
• Leaks in hose connection • Reconnect hose or replace clamp
• Damaged coolant hose • Replace hose
• Leaks in water pump gasket • Replace gasket
• Leaks in water pump internal seal • Replace water pump
• Leaks in coolant inlet cap • Replace water inlet cap gasket
• Leaks in thermostat housing • Replace thermostat sealing
• Improper tightening torque of cylinder head • Retighten
• Damaged cylinder head gasket • Replace cylinder head gasket
Excessively • Coolant leaks (too low coolant level) • Add coolant
high coolant • Improper coolant mixture ratio • Check coolant concentration
temperature
• Kinked coolant hose • Repair or replace hose
• Defective thermostat • Replace thermostat
• Defective water pump • Replace water pump
• Defective radiator • Replace radiator
• Defective coolant reservoir and cap • Replace coolant reservoir or cap
• Cracks on cylinder head or cylinder block • Replace cylinder head or cylinder block
• Clogged coolant passages in cylinder head or cylinder block • Clean coolant passages
• Clogged radiator core • Clean radiator core
• Improper operation of cooling fan • Replace cooling fan or repair related circuit
• Faulty temperature sensor or defective harness • Replace sensor or repair related circuit
Excessively • Stuck thermostat (with open) • Replace thermostat
low coolant • Improper operation of cooling fan • Replace cooling fan or repair related circuit
temperature
• Faulty temperature sensor or defective harness • Replace sensor or repair related circuit

AFFECTED VIN
DI06-14
INSPECTION AND REPAIR
INSPECTION
Cooling System
1. Release the pressure from coolant reservoir by loosening
one notch of coolant reservoir cap, and then remove the
cap.
Notice
Scalding hot coolant and steam could be blown out

under pressure, which could cause serious injury.
Never remove the coolant reservoir cap when the
before the temperature goes down below 90°C.
Y220_06019
2. Add the coolant up to upper mark (arrow) on the reservoir.
3. Install the tester to the coolant reservoir and apply the

pressure of 1.4 bar.
4. Check the coolant hoses, pipes and connections for leaks
after the pointer of the tester drops. Replace or retighten
as required.
Y220_06020
Thermostat
Temperature gauge
Immerse the thermostat into the water. Heat the water and
check the valve opening temperature.
Valve opening temperature DI Engine: 85 ± 2°C
Y220_06021

AFFECTED VIN
DI06-15
Coolant Temperature Gauge Unit

1. Immerse the senor unit into the water. Heat the water
and check the resistance.
Y220_06022
2. If the measured resistance is out of specified value,

replace the gauge unit.
3. Measure the resistance between terminal A and gauge
unit housing, and terminal B and gauge unit housing.
Terminal A
Terminal B
Terminal A 0.4 Ω / 79°C
(for coolant temp.) 23.8 Ω / 115°C
Terminal B 24.8 Ω / -20°C
(for glow plug) 3.25 Ω / 20°C
Y220_06023
Thermostat
1. Immerse the thermostat into the oil. Heat the oil until it
reaches the specified temperature and check if the
coolant temperature switch is turned “OFF”.
Coolant temperature at
113 ± 3°C
point A
Coolant temperature at
point B 116°C
Y220_06024
Notice
Use only engine oil for this inspection. Stir the oil
during heating it. Never heat the oil over required
temperature.

AFFECTED VIN
DI06-16
REMOVAL AND INSTALLATION
Coolant Hose (Inlet/Outlet)

Preceding Work: Draining of coolant
1. Loosen the clamp and remove the coolant outlet hose
(engine to radiator).
Y220_06025

3. Remove the air intake duct from the air cleaner.
Y220_06026
4. Loosen the clamp and remove the coolant inlet hose

(radiator to thermostat housing).
Y220_06027

AFFECTED VIN
DI06-17

6. Loosen the clamp and remove the lower inlet hose.
Y220_06028
Shroud and Cooling Fan/Clutch

Preceding Works:
- Draining of coolant
- Removal of coolant inlet and outlet hose
- Removal of V-belt
Y220_06029
2. Remove the air intake hoses.

3. Set aside the coolant return pipe.
Y220_06030
4. Unscrew the upper bolts and loosen the shroud.
Y220_06031

AFFECTED VIN
DI06-18
5. Unscrew the center bolt and remove the cooling fan clutch
while holding the pulley with counter holder (special tool).
Installation Notice
Y220_06033
6. Remove the shroud.

Y220_06034

AFFECTED VIN
DI06-19
Water Pump - Assembly

Preceding Works:
- Removal of V-belt
- Removal of shroud
- Removal of cooling fan
Y220_06035
1. Thermostat housing 4. Belt pulley

2. Gasket ........................................................... Replace 5. Bolt ................................................................... 10 Nm
3. Bolt ................................................................... 10 Nm 6. Water pump
1. Remove the V-belt while pressing down the auto tensioner

adjusting bolt.
Y220_06036

AFFECTED VIN
DI06-20
2. Unscrew the bolts and remove the EGR pipe and bracket.
Installation Notice
Y220_06037
3. Unscrew the bolts and remove the belt pulley while

holding the belt pulley with a special tool.
Installation Notice
Y220_06038
4. Remove the oil dipstick tube.
Notice
• Replace the O-ring in oil dipstick with new one.

• Plug the oil dipstick hole with a cap not to get the
foreign materials into the engine.
Y220_06039
5. Unscrew the bolts and remove the water pump assembly.

Installation Notice
Notice
Remove the gasket residues from the sealing surface

and replace the gasket with new one.
Y220_06040 6. Install in the reverse order of removal.

AFFECTED VIN
DI06-21
Thermostat
* Preceding Works:
- Removal of V-belt
- Removal of cooling fan
- Removal of intake duct (air cleaner to turbo charger)
Y220_06041
1. Gasket ...................................................... Replace 5. Thermostat

2. Water pump housing 6. Seal
3. Connector 7. Coolant hose
4. Bolt ............................................................. 10 Nm

AFFECTED VIN
DI06-22
1. Unscrew the bolts and remove the thermostat housing.

Installation Notice
Y220_06042
2. Remove the thermostat.

Y220_06043

AFFECTED VIN
DI06-23
Water Pump Housing

Preceding Works:
- Removal of water pump assembly
- Removal of thermostat assembly
1. Remove the heater hose.
Y220_06044
2. Unscrew the bolts and remove the alternator.

Installation Notice
Y220_06045
3. Unscrew the bolts and remove the alternator bracket.

Installation Notice
Y220_06046
4. Unscrew the bolts and remove the water pump housing.

Installation Notice
Notice
• Be careful not to damage the O-ring in coolant outlet

pipe (cylinder head side).
• Remove the gasket residues from the sealing
surface and replace the gasket with new one.

AFFECTED VIN
DI06-24
Radiator
Preceding Work: Draining of coolant
Y220_06048
2. Remove the clips and washers from bottom of radiator at

both sides.
Notice
Be careful not to damage the rubber bushing.
Y220_06049
3. Unscrew the bracket mounting bolts under the radiator

condenser.
Installation Notice
Y220_06050
4. Disconnect the oil inlet and outlet hoses from bottom of

radiator.
Notice
• Plug the radiator oil holes with caps.

• Replace the hose washers with new ones.
Y220_06051

AFFECTED VIN
DI06-25
5. Remove the coolant outlet hose.
Y220_06052
Y220_06053
7. Remove the coolant inlet hose and the cooler inlet hose.
8. Remove the coolant return hose.
Y220_06054
9. Unscrew the bolts and remove the shroud.
Y220_06055

AFFECTED VIN
DI06-26
10. Unscrew the bolts and remove the radiator upper plate.
Installation Notice
Y220_06056
11. Unscrew the bracket mounting bolts on the radiator

condenser.
Installation Notice
Y220_06057
12. Remove the radiator by pulling it up carefully.
Y220_06058

AFFECTED VIN
DI06-27
Coolant Reservoir
1. Drain the coolant.
2. Remove the hoses.
Y220_06059
3. Unscrew the bolts and remove the coolant reservoir.

Installation Notice

AFFECTED VIN
DI06-28
Draining and Adding of Coolant

1. Release the pressure from coolant reservoir by loosening
one notch of coolant reservoir cap, and then remove the
cap.
Notice
Scalding hot coolant and steam could be blown out

under pressure, which could cause serious injury.
Never remove the coolant reservoir cap when the
before the temperature goes down below 90°C.
Y220_06061
2. Loosen the drain plug in bottom of radiator and drain the

coolant.
Notice
Collect the drained coolant with a proper container.
Y220_06062
3. Remove the drain plug (1) and seal (2) in the cylinder
block and drain the coolant.
4. Replace the seal with new one and install the drain plug.
Installation Notice
Y220_06063
5. Install the drain plug in bottom of radiator.

6. Add the coolant through the coolant reservoir.
Notice
• Keep the coolant mixture ratio of 50:50 (water : anti-

freezer).
• Add the coolant until the water flows out through
the overflow hose.
7. Warm up the engine until the thermostat begins to open

and check if the coolant level is at “FULL” mark on the
reservoir. Add if necessary.

AFFECTED VIN
DI06-29
PREHEATING SYSTEM
ECU Glow indicator (meter cluster)
Glow plug Preheating relay
Y220_06068

AFFECTED VIN
DI06-30
OVERVIEW
Glow plug is installed on the cylinder head (combustion chamber) in the D27DT preheating control unit system. Cold
starting performance has improved and exhaust gas during cold starting has reduced.
ECU receives coolant temperature and engine speed to control; after monitoring the engine preheating/after heating and
glow plug diagnosis function, the fault contents will be delivered to ECU.
• Engine preheating/after heating functions

• Preheating relay activation by ECU controls
- Senses engine temperature and controls the preheating/after heating time
- Glow indicator
• K-LINE for information exchanges between preheating unit and ECU
- Transmits preheating unit self-diagnosis results to ECU
- Transmits glow plug diagnosis results and operating status to ECU
PREHEATING RELAY
Structure
K-LINE #1 IG1
(ECU 34) Power terminal
Glow plug
control signal
K (ECU 113)
R/Y
Ground terminal
B+main wire
(12V)
STICS terminal
Glow plug (remote start)
terminal
Y220_06069

AFFECTED VIN
DI06-31
PREHEATING SYSTEM DIAGRAM
STICS(remote start)
Coolant
temperature
sensor
Y220_06070
Specifications
Rated voltage DC 12 V
Operating voltage range DC 8 ~ 15 V
Operating range - 40 ~ + 100°C
Relay operating voltage Over 6.5 V
Relay releasing voltage Over 1.5 V
Relay coil resistance 11.3 Ω
Voltage drop Below 150 mV at each glow plug (at 16A of current)
Parasitic current MAX 1mA

AFFECTED VIN
DI06-32
Function
Preheating system controls and checks following functions and operating conditions.
Pre-Heating
• The power will be supplied to the glow plugs by ECU controls when the power is supplied to the IG terminal from
the battery and there are normal communications with ECU within 2 seconds. The surface of glow plug will be
heated up to 850°C very quickly to aid combustion by vaporizing air-fuel mixture during compression stroke.
• Preheating time is controlled by ECU.
After-heating
• When the engine is started, after-heating starts by ECU controls. The idle rpm will be increased to reduce toxic
smoke, pollutants and noises.
• After-heating time is controlled by ECU.
Checking glow plugs
• Check each glow plug for short in circuit
• Check each glow plug for open in circuit due to overvoltage
• Check glow plug for short to ground
Forceful relay shut-down
• When glow plug is shorted to ground
K-Line communication
• ECU sends the results to preheating time control relay through K-Line to start communication.
• Preheating time control relay sends messages including self-diagnosis data for glow plugs to ECU.
• Glow plug makes communication only as response to demand.
• When power is supplied, ECU starts self-diagnosis within 2 seconds.
• Under the following conditions, communication error occurs.
- When there is no response from glow plug module within 2 seconds
- When an error is detected in checksum
- Less byte is received
Error code of “P1720 - Pre heating control communication fail” will be reported.
Operating time
Coolant Temp. -35 °C -25 °C -20 °C -10 °C 0 °C 10 °C 20 °C

Pre- Operating Time 31 sec 22 sec 19 sec 17 sec 14 sec 0 sec 0 sec
heating Operating • IG: “ON” Release • After operating time elapsed
Conditions • B+ : below 15.2V Conditions • IG: “OFF” • When engine cranking
Coolant Temp. -30 °C -20 °C -10 °C 0 °C 10 °C 20 °C 35 °C

Operating Time 115 sec 80 sec 30 sec 19 sec 11 sec 11 sec 0 sec
After-
heating • After engine starting • After operating time elapsed
Operating Release
• Torque : 190/170 Nm
Conditions Conditions
• Speed: 2100/2050 rpm
Coolant Temp. -30 °C -25 °C -20 °C -10 °C 0 °C 10 °C 20 °C
Glow Operating Time 18 sec 16 sec 10 sec 5 sec 2 sec 0 sec 0 sec
Indicator Operating Release
• IG: “ON” • When engine cranking
Conditions Conditions

AFFECTED VIN
SECTION DI07
FUEL SYSTEM
DI07-1
SECTION
00 DI07
FUEL SYSTEM
Table of Contents
CAUTIONS FOR DI ENGINE ....................................... DI07-3
FUEL SYSTEM ............................................................ DI07-6

Fuel injection system .............................................. DI07-6
Fuel transfer line ................................................... DI07-12
Inlet metering valve (IMV) ..................................... DI07-14
High fuel pressure line .......................................... DI07-17
Injector .................................................................. DI07-48
FUEL SYSTEM CHANGED BY

AFFECTED VIN
DI07-3
CAUTIONS FOR DI ENGINE

This chapter describes the cautions for DI engine equipped vehicle. This includes the water separation from engine,
warning lights, symptoms when engine malfunctioning, causes and actions.
DI Engine Water Separator Warning Light

Comparatively conventional diesel engines, DI engine con- When the water level inside water sepa-
trols the fuel injection and timing electrically, delivers high rator in fuel filter exceeds a certain level
power and reduces less emission. (approx. 39 cc), this warning light
comes on and buzzer sounds.
Also, the driving force of the vehicle
System Safety Mode decreases (torque reduction). If these
When a severe failure has been occurred in a vehicle, the conditions occur, immediately drain
system safety mode is activated to protect the system. It the water from fuel filter.
reduces the driving force, restricts the engine speed (rpm) For the draining procedures, please re-
and stops engine operation. Refer to “Diagnosis” section fer to “How to drain the water from fuel
in this manual. filter” section.

AFFECTED VIN
DI07-4
Priming Pump
The priming pump installed in fuel pump is the device to fill the fuel into the fuel filter. When the vehicle is under the
conditions as below, press the priming pump until it becomes rigid before starting the engine.
WARNING
Never reverse filter or use it in other place (clean side)
Conditions for using Priming Pump

1. After run out of fuel
2. After draining the water from fuel separator
3. After replacing filter or any intervention on system
Fuel Filter and Water Separator
Y220_07003
1. Fuel filter 2. Water drain plug

3. Priming pump (to be drained every 15,000km max.)
Draining could be done at same time than oil
change
Notice
• When replaced the fuel filter or drained the water from fuel filter, press the priming pump until it becomes
rigid before starting the engine.
• The water drain from fuel filter should be performed whenever changing the engine oil.
CHANGED BY FUEL SYSTEM

AFFECTED VIN
DI07-5
Draining the Water From Fuel Filter

1. Place the water container under the fuel filter.
Y220_07004
2. Turn the drain plug (2) to “A” direction to drain the water.
3. Press priming pump until all water is drained, then turn
the drain plug to “B” direction to tighten it.
Notice
Be careful not to be injured by surrounding
equipment during the working procedures.
Y220_07005
4. Press the priming pump until it becomes rigid.

5. Start the engine and check the conditions.
6. Clear the fault code of ECU with scan 100.
WARNING
If the priming pump is not properly operated, air may

get into the fuel line. It may cause starting problem
or fuel system problem. Make sure to perform the
job in step 4.
Y220_07006

AFFECTED VIN
DI07-6
FUEL SYSTEM
FUEL INJECTION SYSTEM
Electronic Control of Fuel System
High pressure pump

Common rail
IMV valve
Low and high Injection
pressure pump pipe
Fuel temperature
sensor
Water separator
Fuel filter
Priming
pump
Water detection
sensor
Injectors
Sensors
HFM sensor
Cam position sensor
Crankshaft position sensor
Fuel tank ECU
Knock sensor, etc.
System composition
Supply line
- High pressure fuel pump - Fuel rail - Fuel pressure sensor
Return line
- Fuel injector - Electronic control unit (ECU) - Other sensors and actuators ECU connecting line
Y220_07007
ECU receives signals from sensors via data line and then performs effective engine air-fuel ratio controls based on those
signals. Engine speed is measured by crankshaft speed (position) sensor and camshaft speed (position) sensor deter-
mines injection order and ECU detects driver’s pedal position (driver’s demand) through electrical signal that is gener-
ated by variable resistance changes in accelerator pedal sensor. Air flow (hot film) sensor detects intake air volume and
sends the signals to ECU. Especially, the engine ECU controls the air-fuel ratio by recognizing instant air volume
changes from air flow sensor to decrease the emissions (EGR valve control). Furthermore, ECU uses signals from
coolant temperature sensor and air temperature sensor, booster pressure sensor and atmospheric pressure sensor as
compensation signal to respond to injection starting, pilot injection set values, various operations and variables.

AFFECTED VIN
DI07-7
Composition of Fuel System

Components in fuel system are designed to generate and distribute high pressure, and they are controlled electronically
by engine ECU. Accordingly, fuel system is completely different from injection pump type fuel supply system on the
conventional Diesel engine. The fuel injection system in common rail engine is composed of transfer pressure section
that transfers fuel in low pressure, high pressure section that transfers fuel in high pressure and ECU control section.
High pressure pipe
Common rail
Injector
Priming pump
Fuel pump Fuel filter

(High pressure pump, transfer pump)
<Fuel line system>

Y220_07008
Fuel route
Transfer
Fuel tank Priming pump Fuel filter
pump
Transfer pressure line
High pressure Fuel pressure

Injector Common rail
pump regulation valve
High pressure line

AFFECTED VIN
DI07-8
Hydraulic cycle in Fuel Line (Transfer and High Pressure Line)
Transfer pressure Pressure limiter

regulation (High pressure)
Transfer pump High pressure pump
Return
valve
Inlet
valve
below 2 bar
over - 0.48 bar

Venturi Common rail
Up to
1600 bar
Injector
Priming pump
Fuel filter
High pressure supply line

Transfer pressure supply line
Fuel tank Return line
Y220_07009

AFFECTED VIN
DI07-9
Components of Low Pressure Transfer Line

Low pressure stage is to supply sufficient fuel to high pressure section and components are as below.
• Fuel tank (including strainer)
• Hand priming pump
• Fuel filter
• Transfer pump
• Other low pressure fuel hoses
Fuel tank
Fuel tank is made of anti-corrosion material and its allowable
pressure is 2 times of operating pressure (more than 0.3 bar).
It has protective cap and safety valve to prevent excessive
pressure building. Also, it has structure to prevent fuel from
leaking in shocks, slopes and corners and to supply fuel
smoothly.
Y220_07010
Priming pump
If fuel runs out during driving or air gets into fuel line after fuel
filter replacement, it may cause poor engine starting or dam-
age to each component. Therefore, the hand priming pump is
installed to bleed air from transfer line.
When the vehicle is under the conditions as below, press the
priming pump until it becomes rigid before starting the engine.
- After run out of fuel
- After draining the water from fuel filter
- After replacing the fuel filter
Press the priming pump until it becomes rigid before starting
the engine. Y220_07011
Fuel filter
It requires more purified fuel supply than conventional diesel
engine. If there are foreign materials in the fuel, fuel system
including pump components, delivery valve and injector nozzles
may be damaged.
Fuel filter purifies fuel before it reaches to high pressure pump
to help proper operations in high pressure pump. And more, it
separates water from fuel to prevent water from getting into
FIE system (high pressure line).
Y220_07012

AFFECTED VIN
DI07-10
Components of High Pressure Transfer Line

In the high pressure section, sufficient fuel pressure that injectors requires will be generated and stored. The compo-
nents are as below:
• High pressure pump
• Rail pressure sensor
• Pressure limit valve
• Common rail
• High pressure pipe
• Injector
• Fuel pressure regulating valve (IMV)
High pressure pump (including IMV and limit valve)

This is plunger pump that generates high pressure; and driven
by crankshaft with timing chain. The high pressure pump in-
creases system pressure of fuel to approx. 1,600 bar and this
compressed fuel is transferred to high pressure accumulator
(common rail) in tube through high pressure line.
Y220_07013
Common rail (including pressure sensor)

It stores fuel transferred from high pressure pump and also
stores actual high pressure of fuel. Even though the injectors
inject fuel from the rail, the fuel pressure in the rail is main-
tained to a specific value. It is because the effect of accumu-
lator is increased by unique elasticity of fuel. Fuel pressure is
measured by rail pressure sensor. And the inlet metering valve
(IMV) included in high pressure pump housing keeps pres-
sure to a desired level.
Y220_07014
No.1 and 3 cylinder No. 5 cylinder

High pressure pipe (fuel pipe)
Fuel line transfers high pressure fuel. Accordingly, it is made
of steel to endure intermittent high frequency pressure changes
that occur under maximum system pressure and injection
stops. Injection lines between rail and injectors are all in the
same length; it means the lengths between the rail and each
injector are the same and the differences in length are com-
pensated by each bending.
No.2 and 4 cylinder Y220_07015

AFFECTED VIN
DI07-11
Injectors
The fuel injection device is composed of electrical solenoid
valve, needle and nozzle and controlled by engine ECU. The
injector nozzle opens when solenoid valve is activated to di-
rectly inject the fuel into combustion chamber in engine. When
injector nozzle is open, remaining fuel after injection returns
to fuel tank through return line.
Y220_07016
Transfer pump
The transfer pump is included in the housing of the high pres-
sure pump. The transfer pump is the volumetric blade type
pump. To deliver the continuously required fuel volume, the
pump transfers fuel from the fuel tank to high pressure pump.
Y220_07017
Fuel Filter Replacement

* Fuel filter change interval: every 30,000 km
* Water separation interval: every 15,000 km max. (same with engine oil change interval)
* Never reuse the removed fuel filter

AFFECTED VIN
DI07-12
FUEL TRANSFER LINE

Transfer Pump
Description
The transfer pump is the device to provide sufficient fuel to high fuel pressure line and is mechanical type feed pump that
is driven by timing chain linked to crankshaft. This mechanical type feed pump is subject to air inflow, therefore, a hand
priming pump is installed to fill fuel in Low fuel pressure(LP) circuit.
The transfer pump is included in the housing of the HP pump. The transfer pump is the volumetric blade type pump and
consists of the following components:
• A rotor turned by the shaft of the HP pump. The connection is provided by splines.
• An eccentric liner fixed to the housing of the HP pump by 6 Torx bolts. The liner is positioned by two off-set pins in
order to prevent any assembly errors.
• Four blades set at 90°. Each blade is held against the liner by a coil spring.
• The inlet and outlet orifice.
Transfer pump HP pump
<Sectional view of fuel pump>
<Sectional view of transfer pump>
Y220_07018

AFFECTED VIN
DI07-13
Principle of operation
Housing Rotor
Blade
Chamber
Y220_07025
Consider the chamber between the rotor, the liner and two successive blades (refer to above figure).
• When the chamber is in position 1, the volume of the chamber is minimal. The changes in volume according to the
angle of rotation of the rotor are small.
• The rotor makes a quarter turn clockwise. The previous chamber is now in position 2.
The inlet orifice is uncovered. The volume contained in the chamber quickly rises. The pressure inside the chamber
drops sharply. Fuel is drawn into the chamber.
• The rotor continues to rotate. It is now in position 3. The inlet and outlet orifices are now sealed off. The volume area
controlled by the rotor, the liner and the two blades is at the maximum. The changes in volume according to the
angle of rotation of the rotor are small.
• The rotor continues to rotate. It is finally in position 4. The outlet orifice is uncovered. The volume area controlled by
the rotor, the liner and the blades decreases quickly. The pressure inside the chamber rises sharply. The fuel is
expelled under pressure. The depression caused by the transfer pump’s rotation is sufficient to draw in diesel fuel
through the filter. The transfer pump is driven by the shaft of the HP pump, transfer pressure thus rises with engine
speed. A regulating valve allows the transfer pressure to be maintained at a practically constant level (about 6 bar)
throughout the whole range of engine operations by returning some of the fuel to the pump inlet.
Fuel
pressure
(bar)
Fuel pump speed (rpm)

Y220_07026
Characteristics of the transfer pump
Regulating pressure 6 bar

Volume controlled 5.6 cm3/revolution
Flow 90 /h at 300 rpm pump
650 /h at 2,500 rpm pump
Intake capacity 65 mbar at 100 rpm pump

AFFECTED VIN
DI07-14
INLET METERING VALVE (IMV)
Overview
The LP actuator, also called the inlet metering valve, is used

to control the rail pressure by regulating the amount of fuel
which is sent to the pumping element of the HP pump.
This actuator has two purposes:
Y220_07027
IMV effect
1. Firstly, it allows the efficiency of the injection system to
be improved, since the HP pump only compresses the
without IMV amount of fuel necessary to maintain in the rail the level
with IMV of pressure required by the system as a function of the
engine’s operating conditions.
Torque (Nm)
Rail pressure = 80 bar Y220_07028
2. Secondary, it allows the temperature to be reduced in

Fuel temperature at
system backleak
without IMV the fuel tank. When the excess fuel is discharged into
with IMV the back leak circuit, the pressure reduction in the fluid
(from rail pressure down to atmospheric pressure) gives
off a large amount of heat. This leads to a temperature
Fuel Temp.(°C)
rise in the fuel entering the tank. In order to prevent too

high a temperature being reached, it is necessary to limit
the amount of heat generated by the fuel pressure
reduction, by reducing the back leak flow. To reduce the
back leak flow, it is sufficient to adapt the flow of the HP
pump to the engine’s requirements throughout its
operating range.
Torque (Nm)
Y220_07029

AFFECTED VIN
DI07-15
Composition of IMV
The IMV is located on the hydraulic head of the pump. It is fed with fuel by the transfer pump via two radial holes. A
cylindrical filter is fitted over the feed orifices of the IMV. This makes it possible to protect not only the LP actuator, but
also all the components of the injection system located downstream of the IMV.
The IMV consists of the following components:
• A piston held in the fully open position by a spring.
• A piston filter located at inlet.
• Two O-rings ensuring pressure tightness between the hydraulic head and the body of the IMV.
• A body provided with two radial inlet holes and an axial outlet hole.
• Coil
Transfer pump Solenoid

Fuel
Filter Spring
High pressure Piston
Outlet hole O-ring

Fuel
Transfer pump
Y220_07019

AFFECTED VIN
DI07-16
Principle of Operation
The LP actuator is used to proportion the amount of fuel sent to the pumping element of the HP pump in such a way that
the pressure measured by the HP sensor is equal to the pressure demand sent out by the ECU. At each point of
operation, it is necessary to have:
• Flow introduced into the HP pump = Injected flow + Injector backleak flow + injector control flow
The IMV is normally open when it is not being supplied with fuel. It cannot therefore be used as a safety device to shut
down the engine if required.
The IMV is controlled by current. The flow/current law is represented below.
Flow / Current Law

Flow (I/hr)
Current (mA)
Y220_07020
Specifications
Piston stroke 1.4 mm
Diameter of holes 3.4 mm
Coil resistance 5.4 Ω (at 25°C)
Power supply Battery voltage (It is prohibited to supply the IMV directly at the battery voltage
during the diagnostic test)
Max. current 1A
Weight 260 g
Operating temperature 40°C < T < 125°C
Fluid temperature 40°C < T < 90°C
Control logic Normally open without power (The flow decreases as the current rises).
• ECU determines the value of the current to be sent to the IMV according to:
• Engine speed
E
• Flow demand • Inlet Metering
C
• Rail pressure demand Valve (IMV)
U
• Measured rail pressure

AFFECTED VIN
DI07-17
HIGH FUEL PRESSURE LINE

High Pressure Pump
Description
This pump generates high fuel pressure and is driven by timing chain (radial plunger principle). This pump pressurizes
the fuel to approx. 1600 bar and sends this high pressurized fuel to high pressure accumulator (common rail) via high
pressure line.
It is possible to extend the pumping phase in order to considerably reduce drive torque, vibration and noise since the pump no
longer determines the injection period. The differences from conventional rotary pumps lies in the fact that it is no longer the
hydraulic head rotor which turns inside the cam, but the cam which turns around the hydraulic head. Thus, any problems of
dynamic pressure tightness are eliminated because the high pressure is generated in the fixed part of the pump.
1. IMV (Inlet Metering Valve)

2. Hydraulic Head
3. Plunger
4. Drive shaft and cam ring
5. Housing
6. Roller and shoe
7. Transfer pump
8. Fuel temperature sensor
Fuel 9. High fuel pressure - OUT
discharge
10. Pressure regulator
Fuel supply
Y220_07021
Specifications
• Maximum operating pressure: 1600 ± 150 bar
• Max. Overpressure: 2100 bar
• Maximum sealing pressure: when using a plug instead of PRV, no leaks around pump outlet port (when applying
2500 bar of constant pressure)
• Operating temperature: Continuously operating within temperature range of -30°C ~ 120°C in engine compartment
• Inflowing fuel temperature: The maximum inflowing fuel temperature is 85°C (continuously able to operate)
• Pump inlet pressure: Relative pressure Min. - 0.48 bar (to end of filter’s lifetime)
• Driving torque: 15 Nm / 1600 bar
• Gear ratio (engine: pump): 0.625
• Lubrication: - Inside lubrication (rear bearing): Fuel
- Outside lubrication (front bearing): Engine oil

AFFECTED VIN
DI07-18
Principle of operation
• During the filling phase, the rollers are kept in contact with the cam by means of coil springs mounted on either side
of each shoe. The transfer pressure is sufficient to open the inlet valve and to move the pumping plungers apart.
Thus, the dead volume between the two plungers fills with fuel.
• When the diametrically opposite rollers simultaneously encounter the leading edge of the cam, the plungers are
pushed towards each other.
• As soon as the pressure becomes higher than the transfer pressure, the inlet valve closes. When the pressure
becomes higher than the pressure inside the rail, the delivery valve opens. Consequently, the fuel is pumped under
pressure into the rail.
• During the input phase, transfer pressure pushes back the inlet valve. Fuel enters the body of the pumping element.
The valve closes as soon as the pressure in the pumping element becomes higher than the transfer pressure.
• During the input phase, the ball of the delivery valve is subject to the rail pressure on its outer face and to the transfer
pressure on its inner face. Thus the ball rests on its seat, ensuring the pressure tightness of the body of the pumping
element. When the pressure in the element becomes higher than the pressure in the rail, the ball is unbalanced and
it opens. Fuel is then pumped into the rail at high pressure.
Roller
Plunger
<Fuel input> <Pressurize>

Y220_07022
This high pressure pump generates the driving torque with low peak torque to maintain the stress to driving components.
This torque is smaller than that of conventional injection pump, thus, only a small load will be applied to pump. The
required power to drive pump is determined by set pressure for rail and pump speed (delivery flow). Note that the fuel
leakage or defective pressure control valve may affect the engine output.

AFFECTED VIN
DI07-19
Inlet valve and delivery valve

During the input phase, transfer pressure pushes back the inlet valve. Fuel enters the body of the pumping element.
Under the effect of the transfer pressure, the two plungers are forced apart. When the rollers simultaneously encounter
the leading edge of the cam, pressure suddenly rises in the body. Of the pumping element. The valve closes as soon as
the pressure in the pumping element becomes higher than the transfer pressure. During the input phase, the ball of the
delivery valve is subject to the rail pressure on its outer face and to the transfer pressure on its inner face. Thus the ball
rests on its seat, ensuring the pressure tightness of the body of the pumping element. When the two diametrically
opposite rollers encounter the leading edges of the cam, the plungers are forced together and pressure quickly rises in
the body of the pumping element. When the pressure in the element becomes higher than the pressure in the rail, the
ball is unbalanced and it opens. The spring calibration is negligible compared with the pressure forces. Fuel is then
pumped into the rail at high pressure.
<Inlet valve> <Delivery valve>

Y220_07023
Lubrication and cooling of the HP pump

Lubrication and cooling of the pump are provided by the fuel circulation. The minimum flow required to ensure adequate
operation of the pump is 50 /h.
Phasing of HP pump required and offer 2 advantages

Conventional fuel injection pumps ensure pressurizing and distribution of the fuel to the different injectors. It is essential
to set the pump in such a way that the injection occurs at the required place during the cycle. The HP pump of the
common rail system is no longer used for the fuel distribution, it is therefore not necessary to set the pump in relation
to the engine.
Nevertheless, the setting or phasing of the pump offers two advantages:
• It allows the torque variations of the camshaft and the pump to be synchronized in order to reduce the stresses on
the timing belt.
• It allows pressure control to be improved by synchronizing peak pressures produced by the pump with pressure-
drops caused by each injection.
This phasing allows pressure stability to be improved, which helps to reduce the difference in flow between the cylinders.

AFFECTED VIN
DI07-20
HP Pump Fuel Route

The fuel passed through the fuel filter is sent to the transfer pump via the HP inlet pump. this fuel passes through the
transfer pump by the transferring pressure and maintains the predefined value by the regulating valve in HP pump.
Also, this fuel gets into the IMV that controls only the fuel to the high pressure pump.
The below figure describes the pump operations when acceleration and deceleration.
When need high fuel pressure (acceleration)
IMV open
Venturi
to common rail
Fuel supply
to fuel tank
Backleak

Y220_07024

AFFECTED VIN
DI07-21
When do not need high fuel pressure (deceleration)
IMV close
Venturi
to common rail
Fuel supply
to fuel tank
Backleak

Y220_07030
The fuel is sent to the high pressure side (hydraulic head) and compressed by the plunger. And, goes into the common
rail through the high pressure pipe.
The IMV installed in the high pressure side (hydraulic head) of HP pump precisely controls the fuel amount and delivers
the rail pressure feedback same as required amount.
The IMV is controlled by ECU.
Performance curve of HP pump

The time required to obtain a sufficient pressure in the rail to enable the engine to start depends on the volume of the
system (definition of the rail, length of the pipes, etc.). The aim is to reach a pressure of 200 bars in 1.5 revolutions (3rd
compression).
• Maximum operating pressure: 1600 ± 150 bar
Rail pressure (bar)
Engine speed (rpm)
<Pressure curve of HP pump> Y220_07031

AFFECTED VIN
DI07-22
Sectional View of HP Pump
<Transfer Pump> Y220_07032
IMV valve
Drive shaft
<IMV Valve and High Pressure Pump (Drive Shaft)> Y220_07033

AFFECTED VIN
DI07-23
Inlet valve
Temperature sensor
Shoe and roller Supply valve
<Inlet Valve, Outlet Valve, Shoe and Roller, Temperature Sensor>

Y220_07034
<Hydraulic Head>
Y220_07035

AFFECTED VIN
DI07-24
Removal
Preceding Works
- Disconnection of negative battery cable
- Removal of engine cover
The trouble diagnosis should be performed before removing the HP pump. Refer to “Diagnosis” section.
1. Remove the bolts on the fan shroud. Disconnect the air

intake duct from intake manifold and the coolant outlet
port connecting hose.
Notice
Plug the coolant port not to get the coolant into the
engine. Add the coolant as required when installing.
Y220_07036
2. Remove the fan belt while pressing down the auto

tensioner adjusting bolt.
Y220_07037
3. Unscrew the center bolt and remove the cooling fan clutch
while holding the pulley with counter holder (special tool).
4. Remove the fan shroud and fan clutch simultaneously.
Y220_07038

AFFECTED VIN
DI07-25
5. Unscrew the bolts and remove the belt pulley while

holding the belt pulley with a special tool.
Y220_07039
6. Unscrew the upper and lower bolts and remove the auto
tensioner.
Upper bolt 82 ± 6.0 Nm
Lower bolt 32 ± 3.0 Nm
Notice
To prevent oil leaks, store the removed auto tensioner
in upright position.
Y220_07040
7. Unscrew the bolts and remove the idle pulley.
Y220_07041
8. Unscrew the bolts and remove the cooling fan bracket

(timing chain cover side).
Y220_07042

AFFECTED VIN
DI07-26
9. Remove the engine oil filler cap and adjust the mark on
camshaft to TDC position.
Y220_07043
10. Align the TDC mark on the crankshaft pulley to the guide
pin and rotate the pulley 720° counterclockwise. Check
the mark on the camshaft again.
Y220_07044
11. Disconnect the vacuum line of EGR vacuum modulator

(1), the vacuum line of turbo charger vacuum modulator
(2) vacuum line and connectors.
Notice
Be careful not to be mixed the lines when installing.
Y220_07045
12. Unscrew the bolts and remove the intake manifold

mounting bracket.
- Upper bolts: 13M/ 2EA
Lower boltes: 5M/ 2EA (Hexagon bolt)
Y220_07046

AFFECTED VIN
DI07-27
13. Disconnect the connector behind HP pump, fuel pipes

and hose lines.
1) Fuel temperature sensor connector (green)
2) IMV connector
3) Fuel return hose (be careful not to break the HP
pump connecting port)
4) Venturi hose
Notice
Plug each opening with sealing cap.

Y220_07047
14. Remove the coolant temperature sensor and the knock

sensor.
Knock sensor 22 Nm
Temperature sensor 20 Nm
Y220_07048
15. Unscrew the bolts and remove the high fuel pressure
pipes at HP pump and common rail. Plug the openings
with sealing caps.
Notice
Replace the fuel pipes with new ones.
Y220_07049
16. Remove the HP pump mounting bracket at engine.
Y220_07050

AFFECTED VIN
DI07-28
17. Remove the intake EGR pipe and gasket.
Notice
• Replace the removed gasket with new one.

• Replace the removed #1 and #3 pipes with new
ones.
Y220_07050
Y220_07051
19. Loosen the clamp and separate the hose from air cleaner.
Y220_07052
20. Separate the connection lines from turbo charger and

PCV separator.
Y220_07053

AFFECTED VIN
DI07-29
21. Remove the exhaust EGR pipe and gasket (Front side -
10 mm/ 2EA, Exhaust side - 13mm/ 2EA). Remove the
center EGR pipe and mounting bolts (13mm/ 4EA).
Notice
• Replace the removed gasket with new one.
• Replace the removed #1 and #3 pipes with new
ones.
Y220_07054
22. Remove the oil dipstick mounting bracket and oil dipstick
tube with O-ring.
Notice
Replace the O-ring with new one.
Y220_07055
Y220_07056
24. Mark on the HP pump sprocket and timing chain.
Y220_07057

AFFECTED VIN
DI07-30
25. Remove the guide rail pins (lower and upper) with a special
tool.
Y220_07058
26. Install the special tool (1) for holding HP pump sprocket,
unscrew the mounting bolts and remove the sprocket. At
this time, rotate the crankshaft 30° to 45° counterclockwise
to remove the sprocket.
Tightening torque 20 Nm ± 90°
Y220_07059
27. Remove the center nut for HP pump shaft.
Y220_07060
28. Pull out the HP pump bearing with a special tool.
Notice
Be careful not to damage the bearing.
Y220_07061

AFFECTED VIN
DI07-31
29. Remove the HP pump bearing bracket (13mm - 3EA).
Y220_07062
30. Remove the mounting bracket behind the HP pump.

31. Slide the HP pump out rearward while holding it.
Notice
Plugs openings and put it in a box (for returns)
Y220_07063

AFFECTED VIN
DI07-32
Y220_07064
1. HP pump sprocket 7. HP pump external bolt (24 ± 2.4 Nm)

2. 12-sided bolt (20 Nm + 90°) 8. HP pump bearing shaft
3. HP pump bearing housing 9. Oil gallery
4. HP pump (High pressure pump) 10. Bearing bushing
5. HP pump shaft 11. Gasket
6. HP pump center nut (65 ± 5 Nm)

AFFECTED VIN
DI07-33
Installation
1. Install the gasket and HP pump.
Notice
Replace the removed gasket with new one.
Warning
Remove caps at last minute and always change removed HP pipes.
2. Install the HP pump bearing bracket and HP pump to the

cylinder block.
Notice
Align the oil galleries in cylinder block and bearing

bracket.
3. Install the bearing into the bracket.
Y220_07065
4. Temporarily install the upper and lower guide rails to seat

the chain.
5. Temporarily tighten the center nut for HP pump shaft.
Notice
Be careful not to rotate the shaft.
Y220_07067
6. Install the timing chain on the sprocket and lock the

sprocket with a special tool.
Notice
Do not apply excessive force to the timing chain.

Otherwise, the TDC point deviates from correct
position.
Y220_07068

AFFECTED VIN
DI07-34
7. Tighten the center nut for HP pump.
Notice
Replace the center nut with new one.
8. Press the upper and lower guide pins into the guide.
Notice
Check the timing chain and guide pin for contact.

Y220_07069
9. Align the marks on the HP pump sprocket and the timing

chain and tighten the bolts.
Tightening torque 20 Nm + 90°
10. Remove the special tool.
Y220_07070
11. Install the mounting bracket behind HP pump.
Y220_07071
Notice
• Replace the chain tensioner washer with new one.
• Be careful not to drop the washer into the hole.
Y220_07072

AFFECTED VIN
DI07-35
13. Check if the mark on the intake camshaft is at the correct

position through oil filler opening.
Notice
Rotate the bolt on crankshaft damper pulley two

revolutions and check if the mark on the intake
camshaft is at the correct position.
Y220_07073
14. Clean the timing chain cover parting surface and apply
the sealant on it.
Y220_07074
15. Install the timing chain cover.
Notice
Align the cover and the guide pin.
Y220_07075
16. Install the auto tensioner assembly.

- Upper bolt (24M):
- Lower bolt(13M):
Y220_07076

AFFECTED VIN
DI07-36
17. Install the coolant pump pulley.
Y220_07077
18. Install the fan clutch with a special tool.
19. Install the oil dipstick tube and bracket.
Y220_07078
20. Install the exhaust EGR pipe and bracket.
Notice
Make sure that the convex
surface of new steel gasket
is facing the direction as Gasket Installing
direction
shown in the figure.
21. Engage the turbo charger and PCV separator connecting

lines.
Y220_07079
22. Engage the air cleaner hose and tighten the clamp.
Notice 23. Connect the HFM sensor connector.
24. Install the EGR center pipe.
If the initialization of fuel pressure has not been
performed, the engine ECU controls new HP pump Tightening torque 25 ± 2.5 Nm
with the stored offset value. This may cause the
poor engine output. 25. Connect the HP pump connectors and engage the hose lines.
- Fuel temperature sensor connectors and IMV connector
- Venturi hose and fuel return hose
26. Install the coolant temperature sensor and the knock sensor.
27. When replaced the HP pump, initialize the fuel pressure
by using Scan-i. Refer to “Trouble Diagnosis” section in
this manual.

AFFECTED VIN
DI07-37
27. Install the vacuum modulator to the intake manifold

bracket.
28. Connect the vacuum modulator connecting lines and
connector.
(1) Vacuum modulator for turbo charger control
(2) Vacuum modulator for EGR valve control
Notice
Ensure that the vacuum hoses are connected to

correct positions.
Y220_07080
29. Connect the hose to coolant outlet port and tighten the
clamp.
30. Install the air intake duct.
31. Install the fan belt while pressing the auto tensioner
adjusting bolt.
Y220_07081
32. Place the fan shroud in its location and install the cooling
fan by using an open end wrench.
33. Install the fan shroud.

34. Add the coolant.
35. Check all the connections for tightness and pump the
priming pump to deliver the fuel to the transfer line of HP
pump.
36. Start the engine and check if abnormality is present.
37. Run leak detection cycle to get rid of air in the system
using scan 100.

AFFECTED VIN
DI07-38
Fuel Filter
Function
Foreign materials in fuel can damage the pump components, transfer valve and injectors. Therefore, the high pressure
direct injection engine must use fuel filter. Otherwise, the operation performance will drop dramatically. And, diesel fuel
may contain water due to condensation by temperature changes and this condensation water can damage the system
by corroding the injection system. Thus, the common rail engine should have function that can drain water periodically.
from HP pump to fuel tank
to HP pump
from fuel tank
Water Sensor Fuel filter

Capacity: 120 cm3 Filter volume: 500 ± 25 cm 3
Filtering efficiency
Warning light ON level: 75 cm 3
• Particles larger than 3µm > 98 %
• Particles larger than 5µm > 99.8 %
• Particles larger than 15µm > 100 %
Drain plug
Y220_07082

AFFECTED VIN
DI07-39
Change Interval: 30,000 km
Water separation and storage function

• Function: It separates the condensation water from diesel fuel to prevent the water from getting into FIE system, and
results in protection of FIE system. (manual drain)
• Water storage capacity: 120 cc
• Water sensor: light if over 39 cc
• Water drain interval: When changing engine oil or every 20,000 km
Water sensor
It is integrated in the filter and sends signal to ECU when water level reaches at a specified value (over 39 cc) in the filter
to let the driver drain the water.
Fuel De-Waxing – Improving starting performance in cold weather

Due to characteristics of diesel fuel, some of fuel components solidify during cold winter under below a specific tempera-
ture (-15°C). When those symptoms happen, engine may stall; however, some of the fuel (temperature rises due to high
compression) in the HP pump in D27DT engine return to the filter to warm up fuel when temperature is below 50°C by
improving cold start performance during cold winter.

AFFECTED VIN
DI07-40

1. Disconnect the fuel supply and return hoses.
Notice
• Plug the openings of hoses and fuel filter with

sealing caps.
• Ensure that the hoses are connected to correct
positions.
Y220_07084
2. Loosen the bracket bolts and disconnect the hose from

the drain plug.
3. Remove the fuel filter.
5. Press the priming pump until it becomes rigid to deliver
the fuel to the transfer line of HP pump.
Y220_07085

AFFECTED VIN
DI07-41
Priming Pump
If fuel runs out during driving or air gets into fuel line after fuel
filter replacement, it may cause poor engine starting or dam-
age to each component. Therefore, the hand priming pump is
installed to fill filter.
to fuel filter
When the vehicle is under the conditions as below, press the
priming pump until it becomes rigid before starting the engine.
Conditions for using Priming Pump

- After run out of fuel
from fuel tank
- After draining the water from fuel filter
Y220_07086
- After replacing the fuel filter
Notice
When the fuel filter is replaced, the fuel in the fuel tank should be transferred to the filter by using priming
pump. So never transfer the fuel in the fuel tank to the filter by driving HP pump with cranking the engine.
Relations Between Pressure and Temperature In Fuel Transfer Line

Pump inlet pressure
Pump
High pressure common rail
Fuel transfer
line
Injector
Ventury
Pump outlet pressure Injector No.1 return pressure Injector No.5 return pressure
Y220_07087
• The fuel transfer line is the line between fuel tank and HP pump inlet port. The pressure on this line affects the
lifetime of fuel filter.
• Temperature of fuel transfer line
- HP pump inlet temperature is less than 80°C.
- The temperature of fuel pump inlet is up to 80°C.
And, diesel fuel has lubrication effects due to its viscosity. Thus, the fuel is also used for pump lubrication.
However, this lubrication performance drops as the temperature rises. Accordingly, when the fuel temperature is
over 50°C, 100% of fuel is returned to fuel tank to cool down the temperature and then increase the lubrication
effects of fuel and prevent heat damage on each section of high fuel pressure line.

AFFECTED VIN
DI07-42
High Pressure Accumulator (Common Rail)
Y220_07088
Description
The high pressure accumulator reserves the high pressure fuel. Simultaneously, the pressure changes due to the
delivery from HP pump and the fuel injection is diminished by rail volume. This high pressure accumulator is commonly
used in all cylinders. Even when a large amount of fuel leaks, the common rail maintains its internal pressure. This
ensures that the injection pressure can be maintained from when the injector opens.
Function
• Relieve the pressure pulsation
• Provide pressure information to ECU (fuel pressure sensor)
Specifications
• Material: Forged Steel
• Dimension: - Volume: 22 ± 1cc
- Length: Max. 397.7 mm
- Outer diameter: 25.3 mm
• Fuel pressure sensor Integrated type
- Sensor input voltage: 5 ± 0.1V
- Sensor output signal voltage: - 4.055 ± 0.125 V @ 1600 ± 15 bar
- 0.5 ± 0.04 V @ 0 bar
• Operating pressure range
- Normal condition: 0 ~ 1600 bar
- Max. Overpressure: 2100 bar
• Ambient temperature: - available within -40°C ~ 125°C
- Spontaneous max. temperature after engine stops: 140°C (acceptable against total 15 hours)
• Fluid temperature: -40 ~ 100°C under normal operating conditions
• Removal and installation: 10 times without any damage

AFFECTED VIN
DI07-43
No. 1 No. 2 No. 3 No. 4 No. 5
HP pipe
Injector
High fuel pressure pipe
HP pipe
HP pump
<High pressure accumulator>

Y220_07089
High Fuel Pressure Pipe

• Function: Resistant to pressure changes, tightness against surroundings, supplying fuel through pump, rail and
injector with high pressure
• Material: Steel (Zn Plated)
• Common: Cylinder 1 & 3, 2 & 4, 5
• Internal pressure
- Internal operating pressure: 0 ~ 1600 bar during its lifetime
- Spontaneous max. pressure when restoring: 2100 bar (max. total period: 20 hours)
- Bursting pressure: over 2500 bar
• To keep cleanness and tightness, the high pressure pipe assembly should be used only once.
Notice
• Make sure to replace the removed high fuel pressure pipes.

• Tighten the fasteners with the specified tightening torque.

AFFECTED VIN
DI07-44

Preceding Work: Removal of engine cover
1. Disconnect the fuel pressure sensor connector.
Notice
• Replace the fuel pipes with new ones.

• Plug the openings of hole in the common rail with
sealing caps.
• Check pressure is low before opening the circuit.
Y220_07090
2. Unscrew the nuts and remove the fuel supply main pipe
from the fuel line.
Installation Notice
Notice

sealing caps.
Y220_07092 3. Unscrew the high fuel pressure line nuts and remove the
fuel pipes.
Installation Notice
Notice

sealing caps.
4. Unscrew the bolts and remove the common rail

asssembly.
Installation Notice
Notice
sealing caps.
Y220_07093

AFFECTED VIN
DI07-45
Fuel Pressure Sensor
Y220_07094
Fuel pressure sensor on the center of common rail detects instant fuel pressure changes and then sends to ECU. When
received these signals, ECU uses them to control fuel volume and injection time.
The fuel in the rail reaches to sensor diaphragm via blind hole in the pressure sensor and the pressure signal converts to
electrical signal. The signal measured by sensor will be amplified to input to ECU.
This piezo element type sensor changes pressure into electrical signal. Accordingly, when the shape of diaphragm
changes, electrical resistance in the layers on the diaphragm changes then can measure 0.5 ~ 5 V.
• Sensor input voltage: 5 ± 0.1 V
• Output signal voltage of sensor
- 4.055 ± 0.125 V: 1600 ± 15bar
- 0.5 ± 0.04 V: 0 bar

AFFECTED VIN
DI07-46
Sensing area Amplifier

Pres- Physical
Converts to Electrically
sure changes
electric signal amplyfying
signal
<Operation principle of fuel pressure sensor> Y220_07095
Upper area
Output
voltage
Lower area
Pressure (P)
<Sensor voltage> Y220_07096
Piezo resistance
Ground
SIG
REF 5V
Pressure sensor
<Circuit diagram of fuel pressuer sensor> Y220_07097

AFFECTED VIN
DI07-47
Fuel Temperature Sensor
Temperature
Resistance
<Fuel temperature sensor> <Output characteristics of fuel temperature sensor>

Y220_07098
Fuel temperature sensor is a NTC resistor that sends fuel temperature to ECU.
In case of NTC resistor, the resistance lowers if engine temperature rises so the ECU detects lowering signal voltages.
Fuel temperature sensor is installed on the fuel return line to correct pressure after measuring fuel temperature. 5V is
supplied to the sensor and voltage drop by temperature is delivered to ECU to measure the fuel temperature through
analog-digital converter (ADC).
Notice
Fuel temp sensor not to be dismounted.
Signal
Ground
<Circuit diagram of fuel temperature sensor>

Y220_07099
HFM Sensor
- Refer to “Intake System”
Crankshaft Position Sensor

- Refer to “Engine Assembly”
Knock Sensor
Camshaft Position Sensor


AFFECTED VIN
DI07-48
INJECTOR
The C21 labels including injector characteristics are attached in each injector. These C21 values should be input to ECU
by using Scan-i when replacing the ECU or injectors.
Special cautions:
1. Plug the openings of hoses and pipes with the sealing caps.
2. Replace the copper washer with new one plus injector holder bolt & washer.
3. Tighten the injector holder bolts with the specified tightening torque.
4. Be careful not to drop the injector.
Specifications
Length: · Injector body 181.35 mm
· Injector nozzle 22.155 mm
Nozzle basic: 5 Holes, 146°C Cone Angle,
840 mm3/min
Control: PWM type (solenoid injector)
Edge filter
Tightening: Clamping by fork
Leak off nipple Fuel return: Nipple
C2I label
Nozzle holder body
Bobbin
C2I value Control valve
Cap nut Adaptor plate
Nozzle body
Washer
Nozzle needle
Y220_07100

AFFECTED VIN
DI07-49
The maximum injection pressures are approximately 1,600 bar. The forces to be overcome in order to lift the needle of
the injector are therefore very large. Because of this, it is impossible to directly control the injector by using an electro-
magnetic actuator, unless very high currents are used, which would be incompatible with the reaction times required for
the multiple injections. The injector is therefore indirectly controlled by means of a valve controlling the pressurizing or
discharging of the control chamber located above the needle:
• When the needle is required to lift (at the start of injection): the valve is opened in order to discharge the control
chamber into the back leak circuit.
• When the needle has to close (at the end of injection): the valve closes again so that pressure is re-established in
the control chamber.
Valve Valve
In order to guarantee response time and minimum energy
consumption:
• The valve must be as light as possible.
Volume Contact
• The valve stroke must be as short as possible. under making seal
high
• The effort needed to move the valve must be minimal, which pressure
Depressuriza-
means that the valve must be in hydraulic equilibrium in tion grooves
Valve
the closed position. Volume under
Spill
vacuum
Spring pressure ensures contact between the valve and its orifice
seat. To lift the valve, it is therefore required to overcome the
force being applied by this spring.
Y220_07101
Spacer Spacer
The spacer is situated underneath the valve support. It inte-
grates the control chamber and the three calibrated orifice
which allow operation of the injector. These orifices are: INO inlet SPO spill
irifice orifice
• The injector supply orifice (Nozzle Path Orifice: NPO)
• The control chamber discharge orifice (Spill Orifice: SPO)
• The control chamber filling orifice (Inlet Orifice: INO)
Control
NOP nozzle
chamber
path orifice
Y220_07102

AFFECTED VIN
DI07-50
Principle of Operation
Ff
Ff= =pressure * space
S
(Ff
(Ff==PPrail
rail * S) S)
Fo = pressure * space
Fo ==Prail * S)
(Fo
(Fo = Prail A)
Valve closed Valve opens Valve open Valve closes Valve closed
Needle closed Needle closed Needle opens Needle open Needle closed
No injection No injection Start of injection End of injection No injection
Y220_07103
Injector at rest
The valve is closed. The control chamber is subject to the rail
pressure.
The pressure force applied by the fuel onto the needle is:
Ff = S * Prail
The needle is closed and hence there is no fluid circulation
through the NPO orifice. While static, the nozzle produces no
pressure drop. The cone of the needle is therefore subject to
the rail pressure. The force applied by the fuel to the needle is:
Fo = A * Prail
Since Ff > Fo, the needle is held in the closed position. There
is no injection.
Solenoid valve control

When the solenoid valve is energized, the valve opens. The
* S: The area of the flat upper surface of the injector’s needle fuel contained in the control chamber is expelled through the
* A: The area of the needle surface situated above the section discharge orifice known as the Spill Orifice (SPO).
of contact between the needle and its seat
* Ff: The force applied by the fuel onto section “S” As soon as Ff > Fo, the needle remains held against its seat
* Fo:The force applied by the fuel onto section “A” and there is no injection.
Y220_07104

AFFECTED VIN
DI07-51
Start of injection
As soon as Ff < Fo, or in other words:
Pcontrol < Prail * A/S
The needle lifts and injection begins. As long as the valve is open, the injector’s needle remains lifted. When injection
begins, fuel circulation is established to feed the injector. The passage of the fuel through the inlet orifice of the injector
(similar to a nozzle) leads to a pressure drop which depends on the rail pressure.
When the rail pressure is at its highest (1600 bar), this pressure drop exceeds 100 bar. The pressure applied to the cone
of the needle (the injection pressure) is therefore lower than the rail pressure.
End of injection
As soon as the solenoid valve is de-energized, the valve closes and the control chamber is filled. Since the needle is
open, the thrust section areas situated on either side of the needle is therefore to apply different pressures to each of
these faces. The pressure in the control chamber cannot exceed the rail pressure, so it is therefore necessary to limit
the pressure applied to the needle’s cone. This pressure limitation is achieved by the NPO orifice which produces a
pressure drop when fuel is passing through it.
Prail * S (Prail - P) * S
When static, this pressure drop is zero. When the pressure in the control chamber becomes higher than the pressure
applied to the needle’s cone, the injection stops.

AFFECTED VIN
DI07-52
Injecting Process
Fuel is delivered to the injector
Delivered fuel is passed

through supply orifice (1) and
control chamber orifice (2)
The fuel is delivered to the

volume under high pressure
through the spill orifice (3)
Y220_07105

AFFECTED VIN
DI07-53
The fuel is delivered to the

control chamber (4) in spacer
The fuel begins to get into the

nozzle needle (5)
The nozzle needle is filled with

fuel and close the valve (6) by
increased pressure
Y220_07106

AFFECTED VIN
DI07-54
The pressure is delivered to the

spill orifice (3)
The pressure is delivered to the

control chamber (7) and the
nozzle needle (8)
The nozzle needle starts to open

and inject the fuel
Y220_07107

AFFECTED VIN
DI07-55
The nozzle needle blocks the

control chamber (9)
The valve opens due to the

pressure decreases (10)
The pressure is delivered to

control chamber (11)
Y220_07108

AFFECTED VIN
DI07-56
It pushes the nozzle needle and

the control chamber opens (12)
The nozzle closes (13)
Y220_07109

AFFECTED VIN
DI07-57
Fuel pressure
Fuel pressure
• Minimum operating pressure: start injection over 100 bar
• Maximum operating pressure: 1,600 bar (max. operating pressure in normal conditions)
• Max overpressure: 2,100 bar
Maximum fuel volume at each injector cycle

• Pilot Injection 5 mm3
• Main Injection 85 mm3 (within 200 ~ 1,600 bar)
Main injection
Pilot injection
Small injection separation
Y220_07110
• Small injection separation: min. 200

(duration between the end of pilot injection and start of Opening delay definition
main injection)
• Opening Delay
10%
: Delayed time from applying operating voltage to start of signal
Injection rate
amplitude
injection Injector drive pulse
10%
• Adjustment of feedback injection volume: C2I signal
amplitude
Time ( )
Y220_07111

AFFECTED VIN
DI07-58
Injector control
Current
Peak pull current
= 22.0 A
Through pull
current = 7.5 A Peak hold current
= 22.0 A
Through hold current
= 7.5 A
Time
Pull-in period Hold period
Y220_07112
The control current of the coil takes the following form:

The low current allows the Joule effect losses in the ECU and injector to be reduced. The call current is higher than the
hold current because during the hold phase.
• The air gap between the valve and the coil is reduced and the electromagnetic force to be applied to the valve can
thus be reduced. It is no longer necessary to overcome the valve inertia.
Note
Joule Effect: The principle that the heat produced by an electric current is equal to the product of the resistance
of the conductor, the square of the current, and the time for which it flows.
I: current (A)
R: resistance (Ω)
T: time (sec)
H: calori (cal)
Heat capacity (H) = 0.24 I 2RT

AFFECTED VIN
DI07-59
Fuel Injection
Other than conventional diesel engine, common diesel engine use two steps injection as follows:
• Pilot Injection
• Main Injection
In above two step injection, the fuel injection volume and injection timing is calibrated according to fuel pressure and fuel
temperature.
Pilot injection
Before starting main injection, a small amount of fuel is injected to help proper combustion. This injection is for reducing
the engine noise and vibration.
In other words, it makes the pressure increase in combustion chamber during combustion smooth to reduce the engine
noise and vibration (suppressing the surging). Basic values for pilot injection are adjusted according to the coolant
temperature and intake air pressure.
Needle lift (k)

Cylinder pressure (p)
Needle lift (k)

Cylinder pressure (p)
Angle of crankshaft Angle of crankshaft

<Characteristic curve of discharge without pilot injection> <Characteristic curve of discharge with pilot injection>
Y220_07113
Main injection
Actual output from engine is achieved by main injection.
The main injection determines the pilot injection has been occurred, then calculates the injection volume. Accelerator
pedal sensor, engine rpm, coolant temperature, intake air temperature and atmospheric pressure are basic date to
calculate the fuel injection volume in main injection.
Pressure
1. Pilot injection
2. Main injection
1a. Ignition pressure with pilot injection
2a. Ignition pressure without pilot injection
Angle of crankshaft
<Characteristic curve of combustion chamber pressure during pilot injection>

Y220_07114

AFFECTED VIN
DI07-60
Preceding Work: Removal of engine cover

1. Disconnect the injector return hose.
Notice
Plug the openings with sealing caps.
2. Remove the relevant connector for the injector.
Y220_07115
3. Unscrew the bolts and remove the fuel pipes.
Installation Notice
Installation Notice
• Plug the openings of the common rail with sealing
caps.
Y220_07116
4. Unscrew the injector holder bolts.
Installation Notice
9 ± 1.0 Nm
Tightening torque
180° ± 10°
Replace the bolts and washer with new ones.
5. Disconnect the injector holder.
Y220_07117
6. Remove the injectors with a special tool.

Notice
• Plug the openings of the injectors with sealing caps.
• Pull the dropped washer out from the engine with
a special tool.
• Clean carbon deposite in hole with specific tool.
8. Do not forget to update C2I with Scan 100 and cross old
C2I on label fitted on engine.
Notice
Replace the copper washer, holder bolts and washer
Y220_07118
and fuel supply pipes with new ones.
AFFECTED VIN
DI07-61
ECU Wiring Diagram

AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SECTION DI08
ENGINE CONTROL SYSTEM

DI08-1
SECTION
00 DI08
Table of Contents
SENSORS FOR DIAGNOSIS ...................................... DI08-3

Engine ECU and other components ....................... DI08-3
Top view .................................................................. DI08-4
Side view ................................................................. DI08-5
ENGINE CONTROL SYSTEM ..................................... DI08-6
ECU ......................................................................... DI08-6
Fuel pressure control ........................................... DI08-12
Fuel injecstion control ........................................... DI08-13
Fuel flow control .................................................... DI08-14
Individual injector calibration (C2I) ....................... DI08-19
Minimum drive pulse (MDP) learning .................... DI08-21
ENGINE CONTROL SYSTEM CHANGED BY

AFFECTED VIN
DI08-3
SENSORS FOR DIAGNOSIS
ENGINE ECU AND OTHER COMPONENTS

ECU/barometric Camshaft position Fuel filter Accelerator pedal
sensor sensor (water sensor) sensor
HFM sensor / intake air

temperature sensor
Preheating relay PTC Box
Y220_08001

AFFECTED VIN
DI08-4
TOP VIEW
Booster pressure
Fuel pressure sensor sensor
Injectors (5) Glow Plugs (5)
Y220_08002
CHANGED BY ENGINE CONTROL SYSTEM

AFFECTED VIN
DI08-5
SIDE VIEW
Coolant temperature Knock sensors (2)

sensor
Fuel pressure Crankshaft position

Fuel temperature sensor regulating valve sensor
Y220_08003

AFFECTED VIN
DI08-6
ECU
ECU receives signals from sensors through data line and then performs effective engine air-fuel ratio controls based on
those signals.
Engine speed is measured by crankshaft speed (position) sensor and camshaft speed (position) sensor determines
injection order and ECU detects driver’s pedal position (driver’s demand) through electrical signal that generated by
variable resistance changes in accelerator pedal sensor.
Air flow (hot film) sensor detects intake air volume and then transmits to ECU. Especially, the engine ECU controls the
air-fuel ratio by recognizing instant air volume changes through air flow sensor to pursue low emission gases (EGR valve
control). Furthermore, the ECU uses signals from coolant temperature and air temperature sensor, booster pressure
sensor and atmospheric pressure sensor as compensation signal to respond to injection start and pilot injection set
values and to various operations and variables.
Y220_08004

AFFECTED VIN
DI08-7
Pin No. Description Pin No. Description

1 Engine ground 40 Fuel filter water detection sensor
2 Engine ground 41 RPM signal output
3 Main power (IG 1) 42
4 Main power (IG 1) 43
5 Main power (IG 1) 44 Knock sensor signal (#2)
6 Rail pressure sensor power supply 45 Knock sensor signal (#1)
7 46 Knock sensor ground (#1)
8 47
9 ECU power hold relay 48
10 49
11 50 Auto cruise result signal
12 ABD signal 51
13 52
14 ACC 2 sensor ground 53 ACC 1 sensor ground
15 54 CAN- H1
16 55
17 Auto cruise OFF 56
18 Auto cruise safety switch 57 ACC 2 sensor power supply
19 A/C pressure signal 58 Brake lamp switch
20 Fuel filter water detection warning lamp 59
21 Remote starter output 60 Vehicle speed indication lamp
22 Glow plug control 61 Preheater #1
23 Glow plug warning lamp 62 Preheater #2
24 63 Knock sensor ground (#2)
25 Rail pressure sensor signal 64 HFM sensor (air temperature sensor)
26 Rail pressure sensor ground 65
27 66 Engine ground
28 Engine ground 67 Auto cruise deceleration signal
29 68
30 69
31 Auto cruise acceleration signal 70
32 ACC 2 sensor signal 71 ACC 1 sensor signal
33 72 ACC 1 sensor power supply
34 K-LINE #1 73 CAN -LO
35 K-LINE #2 74
36 Vehicle speed sensor signal input 75
37 IG 1 76 A/C cycling pressure switch
38 Clutch pedal switch 77 Brake pedal switch
39 78 Trip computer

AFFECTED VIN
DI08-8
Pin No. Description Pin No. Description

79 A/C relay 101 Coolant temperature signal
80 Cooling fan LOW 102 Coolant temperature sensor ground
81 Cooling fan HIGH 103 Camshaft position sensor signal
82 Crankshaft position sensor (-) 104 Camshaft position sensor ground
83 HFM sensor (air mass sensor) 105 Engine check warning lamp
84 HFM sensor (ground) 106
85 107 Blower switch
86 HFM sensor (power supply) 108 Booster pressure sensor power supply
87 IMV (fuel pressure regulating valve) 109 Fuel temperature sensor signal
88 Engine ground 110 Fuel temperature sensor ground
89 111 Camshaft position sensor power supply
90 Crankshaft position sensor (+) 112 Immobilizer
91 113 Engine check warning lamp
92 114 Injector #1
93 115 Injector #4
94 116 Injector #3
95 Waste gate actuator 117 Injector ground (#1, 3, 4)
96 EGR valve 118 Injector ground (#2, 5)
97 119
98 120 Injector #5
99 Booster pressure sensor signal 121 Injector #2
100 Booster pressure sensor ground

AFFECTED VIN
DI08-9
ECU Inputs·Outputs
Inputs Control Output
Booster pressure sensor

Atmospheric pressure sensor Injector
(Built-in ECU) EGR system
Air flow sensor (HFM) Fuel pressure regulating valve (IMV)
Coolant temperature sensor Electrical fan control (Low/High-speed)
Fuel temperature sensor E A/C compressor relay
Fuel pressure sensor Glow plug relay
Fuel filter water sensor Immobilizer
Knock sensor
C Warning lights
crankshaft position sensor (Water warning light, glow plug indica-
camshaft position sensor
U tor light, engine warning light)
Accelerator sensor Preheater (auxiliary heater)
Vehicle speed sensor K - line
Switch input signal CAN communication
(IG, brake, clutch, A/C signal, A/C Self-diagnosis
compressor)
Structure and Function of ECU

Function of ECU
ECU receives and analyzes signals from various sensors and then modifies those signals into permissible voltage levels
and analyzes to control respective actuators.
ECU microprocessor calculates injection period and injection timing proper for engine piston speed and crankshaft
angle based on input data and stored specific map to control the engine power and emission gas.
Output signal of the ECU microprocessor drives pressure control valve to control the rail pressure and activates
injector solenoid valve to control the fuel injection period and injection timing; so controls various actuators in
response to engine changes. Auxiliary function of ECU has adopted to reduce emission gas, improve fuel economy
and enhance safety, comforts and conveniences. For example, there are EGR, booster pressure control, autocruise
(export only) and immobilizer and adopted CAN communication to exchange data among electrical systems
(automatic T/M and brake system) in the vehicle fluently. And Scanner can be used to diagnose vehicle status and
defectives.
Operating temperature range of ECU is normally -40 ~ +85°C and protected from factors like oil, water and electromag-
netism and there should be no mechanical shocks.
To control the fuel volume precisely under repeated injections, high current should be applied instantly so there is
injector drive circuit in the ECU to generate necessary current during injector drive stages.
Current control circuit divides current applying time (injection time) into full-in-current-phase and hold-current-phase and
then the injectors should work very correctly under every working condition.

AFFECTED VIN
DI08-10
Control Function of ECU

• Controls by operating stages
: To make optimum combustion under every operating stage, ECU should calculate proper injection volume in
each stage by considering various factors.
• Starting injection volume control
: During initial starting, injecting fuel volume will be calculated by function of temperature and engine cranking
speed.
Starting injection continues from when the ignition switch is turned to ignition position to till the engine reaches
to allowable minimum speed.
• Driving mode control
: If the vehicle runs normally, fuel injection volume will be calculated by accelerator pedal travel and engine rpm
and the drive map will be used to match the drivers inputs with optimum engine power.

AFFECTED VIN
DI08-11
ECU - Removal and Installation

1. Flip up the front passenger’s seat and remove the ECU
cover nuts.
2. Remove the ECU bracket nuts.
Y220_08005
3. Unscrew the ECU connect bolt and remove the ECU

assembly.
Y220_08006

5. Backup the below data with Scan-i when replacing the
ECU.
- Current ECU data
- Vehicle Identification Number (VIN)
- Variant coding data
- Then, input the data into new ECU. For immobilizer
equipped vehicle, additional coding operation is
necessary.
Y220_08007

AFFECTED VIN
DI08-12
FUEL PRESSURE CONTROL

Fuel Pressure Control Elements
Pressure control consists of 2 principle modules.
• Determines rail pressure according to engine operating conditions.
• Controls IMV to make the rail pressure to reach to the required value.
Pressure in the fuel rail is determined according to engine speed and load on the engine. The aim is to adapt the
injection pressure to the engine’s requirements.
• When engine speed and load are high
: The degree of turbulence is very great and the fuel can be injected at very high pressure in order to optimize
combustion.
• When engine speed and load are low
: The degree of turbulence is low. If injection pressure is too high, the nozzle’s penetration will be excessive and part
of the fuel will be sprayed directly onto the sides of the cylinder, causing incomplete combustion. So there occurs
smoke and damages engine durability.
Fuel pressure is corrected according to air temperature, coolant temperature and atmospheric pressure and to take
account of the added ignition time caused by cold running or by high altitude driving. A special pressure demand is
necessary in order to obtain the additional flow required during starts. This demand is determined according to injected
fuel and coolant temperature.
Fuel Pressure Control

Rail pressure is controlled by closed loop regulation of IMV. A mapping system – open loop – determines the current
which needs to be sent to the actuator in order to obtain the flow demanded by the ECU. The closed loop will correct the
current value depending on the difference between the pressure demand and the pressure measured.
• If the pressure is lower than the demand, current is reduced so that the fuel sent to the high pressure pump is
increased.
• If the pressure is higher than the demand, current is increased so that the fuel sent to the high pressure pump is
reduced.
Flow demand
IMV current
Open
Engine speed
IMV
Current
Rail pressure
demand
Error PIG Correction

governor
Measured rail
pressure
Y220_08008

AFFECTED VIN
DI08-13
FUEL INJECSTION CONTROL

Fuel Injection Control
Injection control is used in order to determine the characteristics of the pulse which is sent to the injectors.
Injection control consists as below.
• Injection timing
• Injection volume
• Translating fuel injection timing and injection volume into values which can be interpreted by the injector driver.
- a reference tooth (CTP)
- the delay between this tooth and the start of the pulse (Toff)
- the pulse time (Ton)
Main injection timing control

The pulse necessary for the main injection is determined as a function of the engine speed and of the injected flow.
The elements are;
• A first correction is made according to the air and coolant temperatures.
This correction makes it possible to adapt the timing to the operating temperature of the engine. When the engine is
warm, the timing can be retarded to reduce the combustion temperature and polluting emissions (NOx). When the
engine is cold, the timing advance must be sufficient to allow the combustion to begin correctly.
• A second correction is made according to the atmospheric pressure.
This correction is used to adapt the timing advance as a function of the atmospheric pressure and therefore the altitude.
• A third correction is made according to the coolant temperature and the time which has passed since starting.
This correction allows the injection timing advance to be increased while the engine is warming up (initial 30 seconds).
The purpose of this correction is to reduce the misfiring and instabilities which are liable to occur after a cold start.
• A fourth correction is made according to the pressure error.
This correction is used to reduce the injection timing advance when the pressure in the rail is higher than the
pressure demand.
• A fifth correction is made according to the rate of EGR.
This correction is used to correct the injection timing advance as a function of the rate of exhaust gas recirculation.
When the EGR rate increases, the injection timing advance must in fact be increased in order to compensate for the
fall in termperature in the cylinder.
During starting, the injection timing must be retarded in order to position the start of combustion close to the TDC. To do
this, special mapping is used to determine the injection timing advance as a function of the engine speed and of the
water temperature. This requirement only concerns the starting phase, since once the engine has started the system
must re-use the mapping and the corrections described previously.
Pilot injection timing control

The pilot injection timing is determined as a function of the engine speed and of the total flow.
The elements are;
• A first correction is made according to the air and coolant temperatures.
This correction allows the pilot injection timing to be adapted to the operating temperature of the engine.
This correction is used to adapt the pilot injection timing as a function of the atmospheric pressure and therefore the
altitude.
During the starting phase, the pilot injection timing is determined as a function of the engine speed and of the coolant
temperature.

AFFECTED VIN
DI08-14
FUEL FLOW CONTROL

Main Flow Control
The main flow represents the amount of fuel injected into the cylinder during the main injection. The pilot flow represents
the amount of fuel injected during the pilot injection.
The total fuel injected during 1 cycle (main flow + pilot flow) is determined in the following manner.
: The driver’s demand is compared with the value of the minimum flow determined by the idle speed controller.
• When the driver depress the pedal, it is his demand which is taken into account by the system in order to
determine the fuel injected.
• When the driver release the pedal, the idle speed controller takes over to determine the minimum fuel which
must be injected into the cylinder to prevent the enigne from stalling.
It is therefore the greater of these 2 values which is retained by the system. This value is then compared with the lower
flow limit determined by the ASR trajectory control system. As soon as the injected fuel becomes lower than the flow
limit determined by the ASR trajectory control system, the antagonistic torque (engine brake) transmitted to the drive
wheels exceeds the adherence capacity of the vehicle and there is therefore a risk of the drive wheels locking. The
system thus chooses the greater of these 2 values (main flow & pilot flow) in order to prevent any loss of control of the
vehicle during a sharp deceleration.
This value is then compared with the flow limit determined by the cruise control. As soon as the injected fuel becomes
lower than the flow limit determined by the cruise control, the vehicle’s speed falls below the value required by the driver.
The system therefore chooses the greater of these 2 values in order to maintain the speed at the required level.
This valve is then compared with the flow limit determined by the flow limitation strategy. This strategy allows the flow to
be limited as a function of the operating conditions of the engine. The system therefore chooses the smaller of these 2
values in order to protect the engine. This value is then compared with the fuel limit determined by the ASR trajectory
control system.
As soon as the injected fuel becomes higher than the fuel limit determined by the ASR trajectory control system, the
engine torque transmitted to the wheels exceeds the adhesion capacity of the vehicle and there is a risk of the drive
wheels skidding. The system therefore chooses the smaller of the two values in order to avoid any loss of control of the
vehicle during accelerations.
The anti-oscillation strategy makes it possible to compensate for fluctuations in engine speed during transient conditions.
This strategy leads to a fuel correction which is added to the total fuel of each cylinder. The correction is determined
before each injection as a function of the instantaneous engine speed.
A switch makes it possible to change over from the supercharge fuel to the total fuel according to the state of the engine.
• Until the stating phase has finished, the system uses the supercharged fuel.
• Once the engine changes to normal operation, the system uses the total fuel.
The main fuel is obtained by subtracting the pilot injection fuel from the total fuel.
A mapping determines the minimum fuel which can control an injector as a function of the rail pressure. As soon as the
main fuel falls below this value, the fuel demand changes to 0 because in any case the injector is not capable of injecting
the quantity demand.

AFFECTED VIN
DI08-15
Driver’s request
Idle speed controller
ASR traction control
Cruise control
Flow limit
Speed limiter
ASR traction control

Engine status
Anti-oscillation strategy
Overflow
Programmed engine stop
Main flow < controllable min.flow
Pilot injection flow
Main flow request

0
Y220_08009
Driver Demand
The driver demand is the translation of the pedal position into the fuel demand. It is calculated as a function of the pedal
position and of the engine speed. The driver demand is filtered in order to limit the hesitations caused by rapid changes
of the pedal position. A mapping determines the maximum fuel which can be injected as a function of the driver demand
and the rail pressure. Since the flow is proportional to the injection time and to the square root of the injection pressure,
it is necessary to limit the flow according to the pressure in order to avoid extending the injection for too long into the
engine cycle. The system compares the driver demand with this limit and chooses the smaller of the 2 values. The driver
demand is then corrected according to the coolant temperature. This correction is added to the driver demand.

AFFECTED VIN
DI08-16
Idle Speed Controller

The idle speed controller consists of 2 principal modules:
• The first module determines the required idle speed according to:
- The operating conditions of the engine (coolant temperature, gear engaged)
- Any activation of the electrical consumers (power steering, air conditioning, others)
- The battery voltage
- The presence of any faults liable to interface with the rail pressure control or the injection control. In this case,
the accelerated idle speed is activated to prevent the engine from stalling when operating in degraded mode.
- It is possible to increase or to reduce the required idle speed with the aid of the diagnostic tool.
• The second module is responsible for providing closed loop control of the engine’s idle speed by adapting the
minimum fuel according to the difference between the required idle speed and the engine speed.
Flow Limitation
The flow limitation strategy is based on the following strategies:
• The flow limitation depending on the filling of the engine with air is determined according to the engine speed and the
air flow. This limitation allows smoke emissions to be reduced during stabilized running.
• The flow limitation depending on the atmospheric pressure is determined according to the engine speed and the
atmospheric pressure. It allows smoke emissions to be reduced when driving at altitude.
• The full load flow curve is determined according to the gear engaged and the engine speed. It allows the maximum
torque delivered by the engine to be limited.
• A performance limitation is introduced if faults liable to upset the rail pressure control or the injection control are
detected by the system. In this case, and depending on the gravity of the fault, the system activates:
- Reduced fuel logic 1: Guarantees 75 % of the performance without limiting the engine speed.
- Reduced fuel logic 2: Guarantees 50 % of the performance with the engine speed limited to 3,000 rpm.
- Reduce fuel logic 3: Limits the engine speed to 2,000 rpm.
The system chooses the lowest of all these values.
A correction depending on the coolant temperature is added to the flow limitation. This correction makes it possible to
reduce the mechanical stresses while the engine is warming up. The correction is determined according to the coolant
temperature, the engine speed and the time which has passed since starting.
Superchager Flow Demand

The supercharge flow is calculated according to the engine speed and the coolant temperature. A correction depending
on the air temperature and the atmospheric pressure is made in order to increase the supercharge flow during cold
starts. It is possible to alter the supercharge flow value by adding a flow offset with the aid of the diagnostic tool.
Pilot flow control

The pilot flow represents the amount of fuel injected into the cylinder during the pilot injection. This amount is determined
according to the engine speed and the total flow.
• A first correction is made according to the air and water temperature.
This correction allows the pilot flow to be adapted to the operating temperature of the engine. When the engine is
warm, the ignition time decreases because the end-of-compression temperature is higher. The pilot flow can therefore
be reduced because there is obviously less combustion noise when the engine is warm.
This correction is used to adapt the pilot flow according to the atmospheric pressure and therefore the altitude.
During starting, the pilot flow is determined on the basis of the engine speed and the coolant temperature.

AFFECTED VIN
DI08-17
Cylinder Balancing Strategy

Balancing of the point to point flows
The pulse of each injector is corrected according to the difference in instantaneous speed measured between 2 succes-
sive injectors.
• The instantaneous speeds on two successive injections are first calculated.
• The difference between these two instantaneous speeds is then calculated.
• Finally, the time to be added to the main injection pulse for the different injectors is determined. For each injector,
this time is calculated according to the initial offset of the injector and the instantaneous speed difference.
Detection of an injector which has stuck closed

The cylinder balancing strategy also allows the detection of an injector which has stuck closed. The difference in instantaneous
speed between 2 successive injections then exceeds a predefined threshold. In this case, a fault is signaled by the system.
Accelerometer Strategy
Resetting the pilot injection
The accelerometer is used to reset the pilot injection flow in closed loop for each injector. This method allows the
correction of any injector deviations over a period of time. The principle of use of the accelerometer is based on the
detection of the combustion noises.
The sensor is positioned in such a way as to receive the maximum signal for all the cylinders. The raw signals from the
accelerometer are processed to obtain a variable which quantifies the intensity of the combustion. This variable, known
as the ratio, consists of the ratio between the intensity of the background noise and the combustion noise.
• A first window is used to establish the background noise level of the accelerometer signal for each cylinder. This
window must therefore be positioned at a moment when there cannot be any combustion.
• The second window is used to measure the intensity of the pilot combustion. Its position is such that only the
combustion noises produced by the pilot injection are measured . It is therefore placed just before the main injection.
The accelerometer does not allow any evaluation of the quantity injected. However, the pulse value will be measured
when the injector starts injection and this pulse value is called the MDP (Minimum Drive Pulse). On the basis of this
information, it is possible to efficiently correct the pilot flows. The pilot injection resetting principle therefore consists of
determining the MDP, in other words the pulse corresponding to the start of the increase in value of the ratio (increase
of vibration due to fuel combustion).
Cylinder pressure
Needle lift
Major pilot injection Ratio
Minor pilot injection
No pilot injection
No injection
Y220_08011

AFFECTED VIN
DI08-18
This is done periodically under certain operating conditions. When the resetting is finished, the new minimum pulse
value replaces the value obtained during the previous resetting. The first MDP value is provided by the C2I. Each
resetting then allows the closed loop of the MDP to be updated according to the deviation of the injector.
Detection of leaks in the cylinders

The accelerometer is also used to detect any injector which may have stuck open. The detection principle is based on
monitoring the ratio. If there is a leak in the cylinder, the accumulated fuel self-ignites as soon as the temperature and
pressure conditions are favorable (high engine speed, high load and small leak).
This combustion is set off at about 20 degrees before TDC and before main injection.
The ratio therefore increases considerably in the detection window. It is this increase which allows the leaks to be
detected. The threshold beyond which a fault is signaled is a percentage of the maximum possible value of the ratio.
Because of the severity of the recovery process (engine shut-down), the etection must be extremely robust.
An increase in the ratio can be the consequence of various causes:
• Pilot injection too strong
• Main combustion offset
• Fuel leak in the cylinder
If the ratio becomes too high, the strategy initially restricts the pilot injection flow and retards the main injection. If the
ratio remains high despite these interventions, this shows that a real leak is present, a fault is signaled and the engine
is shut down.
Detection of an accelerometer fault

This strategy permits the detection of a fault in the sensor or in the wiring loom connecting the sensor to the ECU. It is
based on detection of the combustion. When the engine is idling, the detection window is set too low for the combustion
caused by the main injection. If the ratio increases, this shows that the accelerometer is working properly, but otherwise
a fault is signaled to indicate a sensor failure. The recovery modes associated with this fault consist of inhibition of the
pilot injection and discharge through the injectors.

AFFECTED VIN
DI08-19
INDIVIDUAL INJECTOR CALIBRATION (C2I)

Injected fuel is proportional to square root of injection time and rail pressure.
It is function between pulse and rail pressure and fuel injection curve is called injector characteristics curve having the
following shape.
Delivery (mm3/st)
Drive pulse (µsec)

Y220_08012
Common rail injectors are very accurate components. They are able to inject fuel delivery between 0.5 to 100 mg/str
under pressure varying from 150 to 1600 bar.
This high level of accuracy requires very low machining tolerances (few ).
Nevertheless, due to the machining dispersion, the loss of charge through the functional orifices, the friction between
moving parts and electromagnetic field level are different from one injector to the other. So, the difference of fuel delivery
for the same pressure and the same pulse can reach 5 mg/str from one injector to the other. It is impossible to control
efficiently the engine with such a dispersion between the different injectors. It is necessary to add a correction that
allows injecting the demanded fuel delivery whatever the initial hydraulic characteristics of the injector is. The method
consists in correcting the pulse that is applied to the injector with an offset that depends on the initial hydraulic map of
the injector. So, the pulse should be corrected according to characteristics of each injector.

AFFECTED VIN
DI08-20
C2I is composed of models on these characteristics of injectors.

C2I consists of 16-digit; composed of numbers from 1 to 9 and alphabets from A to F. ECU remembers C2I, character-
istics of each injector, to make the most optimal fuel injection.
• When replacing the injector, C2I code on the top of new injector should be input into ECU because the ECU is
remembering the injector’s C2I value. If C2I is not input, engine power drops and occurs irregular combustion.
• When ECU is replaced, C2I code of every injector should be input. If not, cannot accelerate the vehicle even when
the accelerator pedal is depressed.
C2I Number
(16 digits)
C2I
value
Y220_08013
For coding of C2I, refer to “Diagnosis” section

AFFECTED VIN
DI08-21
MINIMUM DRIVE PULSE (MDP) LEARNING

When the pulse value that the injector starts injection is measured, it is called mininum drive pulse (MDP). Through MDP
controls, can correct pilot injections effectively. Pilot injection volume is very small, 1 ~ 2 mm/str, so precise control of
the injector can be difficult if it gets old. So there needs MDP learning to control the very small volume precisely through
learning according to getting older injectors.
Learning Conditions
Coolant temperature > 75°C
Vehicle speed > 50 Km/h (over 5 seconds)
Intake manifold pressure > 0.7 bar
Engine speed > 2,500 rpm
Battery voltage 10 V < MDP < 16 V
Fuel temperature 0 < fuel temperature < 80 °C
Initial MDP learning on each injector 5 seconds
Trouble Codes
Trouble code Description Diagnosis
P1171 Fault MDP learning on injector No. 1
P1173 Fault MDP learning on injector No. 3 • Check each injector

AFFECTED VIN
DI08-22
Accelerator Pedal Sensor
<Location of accelerator pedal sensor> <When depressing the accelerator pedal

and brake pedal simultaneously>
Y220_08014
Accelerator pedal sensor changes accelerator pedal position into electrical signal and then sends to ECU to let know
the driver’s demand. There are 2 sensors in the accelerator pedal sensor. Accelerator pedal No.1 (ACC 1) sensor signal
determines fuel injection volume and injection timing during driving, and accelerator pedal No. 2 (ACC 2) sensor signal
compares whether the No. 1 sensor signal value is correct.
If accelerator pedal No. 1 and 2 sensors are defective, ECU remembers defect code, and acceleration responses are
getting bad and engine rpm hardly increases.
Notice
When depressing the accelerator pedal and brake pedal simultaneously while driving, the acceleration response
will be diminished abruptly and cannot drive with over 70 km/h even though depressing the accelerator pedal
to its end. At this time, the trouble code of “P-1124 Accelerator pedal sensor stuck” is stored into ECU. If
depressing the accelerator pedal over 3 times, it will be resumed to normal condition.
* For detailed information, refer to “Diagnosis” section in this manual.
Signal 1
Ground
Signal 2
Ground
<Circuit diagram of Accelerator pedal sensor> Y220_08015

AFFECTED VIN
DI08-23
Coolant Temperature Sensor
Temp.
Resistance
<Coolant temperature sensor> <Output characteristics of coolant temperature
sensor>
Y220_08016
Coolant temperature sensor is a NTC resister that sends coolant temperature to ECU.
NTC resister has characteristics that if the engine temperature rises, the resistance lowers so the ECU detects lowering
signal voltages.
If the fuel injected into the engine through injector has more turbulence, then combusts very well. However, if engine
temperature is too low, the fuel injected as foggy state forms big compounds causing incomplete combustion. So the
sensor detects coolant temperature and changes coolant temperature changes into voltage then sends to ECU to
increase the fuel volume during cold start for better starting. And detects engine overheating for fuel volume reduction to
protect the engine.
ECU functions as below with coolant temperature sensor signals.
• When engine is cold, controls fuel volume to correct idle speed.
• When engine is overheated, controls electrical fan and A/C compressor to protect the engine.
• Sends information for emission control.
Temperature (°C) Ω)
NTC 1 Resistance (Ω Ω)
NTC 1 Resistance (Ω
20 2,550 6,062
50 826 1,800
80 321 638
120 123 200
Signal
Auto amp
Ground
<Circuit diagram of coolant temperature sensor> Y220_08017

AFFECTED VIN
DI08-24
Boost Pressure Sensor
Not using terminals
<Location of boost pressure sensor> <Boost pressure sensor>

Y220_08018
Boost pressure sensor uses piezo element and uses only 3 terminals out of 6.
It sets fuel injection timing and corrects fuel injection volume according to atmospheric pressure.
The other function is determining EGR operation stops.
• Output voltage calculation
VO = VS x ( P x 0.004 - 0.04) Voltage (V)
VO : Output voltage
VS : Supply voltage
P : Applying voltage
Pressure (bar)
<Output characteristics of sensor>

Y220_08019
Performance proofing pressure range 20 ~ 250 KPa

Performance proofing temperature range - 40 ~ 110°C
Storage proofing temperature range - 40 ~ 125°C
Performance proofing supply voltage 4.85 ~ 5.35 V
Max. consuming current 10 mA (supply voltage at 5.35 V)
Responsibility TR 7ms

AFFECTED VIN
DI08-25
Ground
REF 5V
SIG
<Circuit diagram of booster pressure sensor>

Y220_08020
Vehicle Speed Sensor

The ABS or ESP control unit sends the vehicle speed signals to ECU. ECU uses these signals to calculate the vehicle
speed and meter cluster shows signals as vehicle speed.
Function
- Limits idle control correction duty range
- Controls cooling fan ABS
or
- Cuts fuel injection if exceeds max. speed ESP control unit
- Controls vehicle shifting feeling
- Used for exhaust gas control mode CAN communication
<Circuit diagram of vehicle speed sensor>

Y220_08021

AFFECTED VIN
DI08-26
Barometric Pressure Sensor

It is built-in the ECU and detects absolute pressure of atmosphere to correct fuel injection timing and injection volume
according to altitude.
Other switches
Brake switch
Brake switch detects brake pedal operations and then sends to engine ECU. It has dual structure with 2 combined
switches and there are brake switch 1 and 2. When these 2 signals are input, engine ECU recognizes as normal brake
signals. These switch signals are related with accelerator pedal sensor operations and used to control the fuel volume
during braking. It means there are no problems in operating accelerator pedal when the brake pedal is operated but the
fuel volume reduces if operates brake pedal while the accelerator pedal is depressed.
Brake pedal switch (NC)
Brake lamp switch (NO)
<Brake switch circuit>

Y220_08022
Clutch pedal switch

Clutch pedal switch is installed on the upper of the clutch and sends clutch pedal operations to engine ECU. Contact
type switch allows engine ECU to recognize the shifting points to correct the fuel volume. It means it corrects fluctuation
happens during gear shifting. Another different function is canceling auto cruise function if equipped (auto cruise control
- equipped for export).
Clutch pedal switch (NO)
Engine
ground
<Clutch pedal switch circuit>

Y220_08023

AFFECTED VIN
SECTION DI09
ELECTRIC DEVICES AND

SENSORS
DI09-1
SECTION
00 DI09
ELECTRIC DEVICES
AND SENSORS
Table of Contents
ELECTRIC DEVICES AND SENSORS ........................ DI09-3

Sensors in engine compartment ............................. DI09-3
Electric devices in engine compartment ................. DI09-4
Specifications .......................................................... DI09-5
Circuit diagram of preheating system ..................... DI09-6
Circuit diagram of starting and alternator .............. DI09-7
TROUBLE DIAGNOSIS ............................................... DI09-8
General ................................................................... DI09-8
Alternator .............................................................. DI09-10
Starter ................................................................... DI09-12
Preheating system ................................................ DI09-14
Preheating time relay ............................................ DI09-16
Glow plug .............................................................. DI09-17
ELECTRIC DEVICES AND SENSORS CHANGED BY

AFFECTED VIN
DI09-3
ELECTRIC DEVICES AND SENSORS
SENSORS IN ENGINE COMPARTMENT
Fuel pressure sensor Booster pressure

sensor
Camshaft position Oil pressure switch

sensor
Coolant temperature Crankshaft position

sensor sensor
Fuel temperature
Knock sensor
sensor
Y220_09001

AFFECTED VIN
DI09-4
ELECTRIC DEVICES IN ENGINE COMPARTMENT
Alternator Glow plug

Capacity
PTC equipped vehicle
: 12V - 140A
FFH equipped vehicle
: 12V - 115A
Air conditioner compressor Starter
Y220_09002
CHANGED BY ELECTRIC DEVICES AND SENSORS

AFFECTED VIN
DI09-5
SPECIFICATIONS
Description Unit Specification
Starter Type - WP220
Output power Kw 2.2
No load test @ 12 volts A 160
Drive pinion speed at no load rpm 4500
Drive pinion speed at load rpm/A 1700/430
Brush length mm 18
Armature diameter mm 55
Armature run-out mm 0.1
Segment groove depth mm 21.7
Alternator Type - CS128D
Output voltage / current V/A PTC equipped vehicle: 12V-140A
FFH equipped vehicle: 12V-115A
Regulator type - ←
Regulating voltage V 14.6
Brush Length mm 12.5
Quantity - 2
Wear limit mm 7
Battery Type - MF
Capacity AH 12V - 90AH
Rupture capatity RC 160
Glow plug Type - Seized type
Rated voltage - 11.5
Circuit connection - Parallel
Preheating time sec Max. 60 ~ 90

AFFECTED VIN
DI09-6
CIRCUIT DIAGRAM OF PREHEATING SYSTEM
Y220_09003

AFFECTED VIN
DI09-7
CIRCUIT DIAGRAM OF STARTING AND ALTERNATOR
Y220_09004

AFFECTED VIN
DI09-8
TROUBLE DIAGNOSIS
GENERAL
No crank • Low battery voltage. • Charging the battery or replace
the battery.
• Battery cable is loose, • Repair or replace the battery
corroded, or damaged. cable.
• Faulty starter motor or starter • Repair or replace the starter
motor circuit is open. motor/starter motor circuit.
• Faulty ignition switch. • Replace the ignition switch.
• Ground short. • Repair the ground short.
Crank ok, but too slow • Low battery voltage. • Charging the battery or replace
the battery.
• Battery. • Repair or replace the battery
• Battery cables are loose, cable.
corroded, or damaged.
• Faulty starter motor. • Repair or replace the starter
motor.
Starter motor does not stop • Faulty starter motor. • Repair or replace the starter
motor.
• Faulty ignition switch. • Replace the ignition switch.
Starter motor running, but not • Broken the clutch pinion gear or • Replace the starter motor.
cranking faulty starter motor.
• Broken the flywheel ring gear. • Replace the flywheel.
• Connected circuit is open. • Repair the open circuit.
Battery discharge • Loosen the generator drive belt. • Adjust the belt tension or replace
the belt.
• The circuit is open or a short. • Repair the open or a short circuit.
• Battery run down. • Replace the battery.
• Open ground circuit. • Repair the open ground circuit.
Charging indicator lamp does not • Charging indicator lamp is blown • Repair or replace the charging
work when the ignition switch on or fuse is blown. indicator lamp/fuse.
(engine does not work) • Faulty ignition switch. • Replace the ignition switch.
• Generator ground circuit is open • Repair the circuit.
or a short.
Charging indicator lamp does not • Battery cable is corroded or • Repair or replace the battery
put out lights after starting the damaged. cable.
engine • Loosen the generator drive belt. • Adjust the belt tension or replace
the belt.
• Faulty wiring harness. • Repair the wiring harness.
Battery over charging • Generator voltage regulator faulty • Replace generator
• Voltage detecfing wiring faulty • Repair wiring

AFFECTED VIN
DI09-9

Hard engine starting • Ignition coil faulty • Replace ignition coil
• Distributor (including optical • Replace distribator (or sensor)
sensor) faulty
• Spark plug malfuntion • Replace spark plug or adjust
clearance
• Ignition timing faulty (spark plug • Resetting valve timing
light is normal)
Unstable engine idling • Spark plug malfunction • Replace spark plug or adjust
clearance
• Ignition coil faulty • Replace ignition coil
• Ignition timing faulty • Resetting valve timing
Enging acceralation malfunction • Ignition timing faulty • Resetting valve timing

AFFECTED VIN
DI09-10
ALTERNATOR
Y220_09005
1. Cooling fan 3. Alternator

2. Bolt ............................................................. 45 Nm 4. Plug connection

AFFECTED VIN
DI09-11

2. Remove the plug connection.
Y220_09006
3. Unscrew the bolts and remove the alternator.

Installation Notice
Tightening torque
Y220_09007

AFFECTED VIN
DI09-12
STARTER
Y220_09A008
1. Starter 3. Nut .................................................................... 15 Nm

2. Washer 4. Bolt ................................................................... 48 Nm

AFFECTED VIN
DI09-13

2. Disconnect the starter terminal.
Y220_09009
3. Lift up the vehicle and remove the front propeller shaft

mounting bolts.
Y220_09010
4. Remove the upper and lower mounting bolts.

AFFECTED VIN
DI09-14
PREHEATING SYSTEM
General
Glow plug is installed on the cylinder head (combustion chamber) in the D27DT preheating control unit system. Cold
starting performance has improved and exhaust gas during cold starting has reduced.
ECU receives coolant temperature and engine speed to control; after monitoring the engine preheating/after heating and
glow plug diagnosis function, the fault contents will be delivered to ECU.
• Engine preheating/after heating functions
• Preheating relay activation by ECU controls
- Senses engine temperature and controls the preheating/after heating time
- Preheating warning light
• K-LINE for information exchanges between preheating unit and ECU
- Transmits preheating unit self-diagnosis results to ECU
- Transmits glow plug diagnosis results and operating status to ECU
STICS (remote start)
Coolant
temperature
sensor
Y220_09012

AFFECTED VIN
DI09-15
Function
Preheating system controls and checks following functions and operating conditions.
• Pre-Heating
: The power will be supplied to the glow plugs by ECU controls when the power is supplied to the IG terminal from
the battery and there are normal communications with ECU within 2 seconds. The surface of glow plug will be
heated up to 850°C very quickly to aid combustion by vaporizing air-fuel mixture during compression stroke.
Preheating time is controlled by ECU.
• While engine starting

: Help to warm up engine
• After-heating
: When the engine is started, after-heating starts by ECU controls. The idle rpm will be increased to reduce toxic
smoke, pollutants and noises.
After-heating time is controlled by ECU.
• Checking glow plugs

- Check each glow plug for short in circuit
- Check each glow plug for open in circuit due to overvoltage
- Check glow plug for short to ground
• Forceful relay shut-down

- When glow plug is shorted to ground
• K-Line communication
- ECU sends the results to preheating time control relay through K-Line to start communication.
- Preheating time control relay sends messages including self-diagnosis data for glow plugs to ECU.
- Glow plug makes communication only as response to demand.
- When power is supplied, ECU starts self-diagnosis within 2 seconds.
- Under the following conditions, communication error occurs.
When there is no response from glow plug module within 2 seconds
When an error is detected in checksum
Less byte is received
Error code of “Pre heating control communication fail” will be reported.

AFFECTED VIN
DI09-16
PREHEATING TIME RELAY

Structure
K-LINE #1 IG1 power

(ECU 34) terminal
Glow plug control

signal
(ECU 113)
Ground
terminal
B+ main
wire (12V)
Relay signal output (5V)
Glow plug terminal to RESTICS
#1~ #4 , #5
Y220_09013
Specifications
Rated voltage DC 12 V
Operating voltage range DC 8 ~ 15 V
Operating range - 40 ~ + 100°C
Relay operating voltage Over 6.5 V
Relay releasing voltage Over 1.5 V
Relay coil resistance 11.3 Ω
Voltage drop Below 150 mV at each glow plug (at 16A of current)
Parasitic current Max. 1mA

AFFECTED VIN
DI09-17
GLOW PLUG
Cylinder type glow plug is inserted into the cylinder and com-
posed of heating pin and housing.
There are heating coil and control coil in the heating pin and
those coils located inside of ceramic cover turn ON or OFF
the internal switch.
Purposes of use
- Preheating before engine starting
- During engine starting
- After-heating after engine starting Y220_09014
Conditions for glow plugs

- Prompt heating and secured temperature stabilities (temperature changes) in low operating voltage
- Should not exceed permissible max. temperature under max. operating voltage
- Heating pin should have good heat-resisting properties against combustion gas and durability
- Material of the glow plug should meet high stressing conditions (e.g., temperature, vibration and environmental
factors)
Specifications
Rated voltage 11 ± 0.1 V
Current consumption Initial current I intial < 30.0 A
Preheating time T 850°C = 5 ± 1.5 sec.
(From ambient temperature up to 85°C)
Operating temperature 900 °C
Tightening torque 15 + 3 Nm
Trouble Code
Refer to “Diagnosis” section in this manual.

AFFECTED VIN
DI09-18

1. Turn the ignition switch to “OFF” position and disconnect
the negative battery cable.
2. Set aside the harnesses on the cylinder head.
Y220_09015
3. Disconnect the glow plug connectors and loosen the glow

plugs.
Installation Notice
Tightening torque
Y220_09016
4. Remove the glow plugs from the cylinder head with a

special tool. Plug the openings of the glow plugs with
sealing caps.
Y220_09017

AFFECTED VIN
DI09-19
Glow plug remover Removal of glow plug
Y220_09018 Y220_09019

AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SECTION DI10
DIAGNOSIS
DI10-1
SECTION
00 DI10
DIAGNOSIS
Table of Contents
SCAN-I OPERATING PROCEDURES -

XDi270 ENGINE .......................................................... DI10-3
TROUBLE DIAGNOSIS TABLE ................................. DI10-23
FUEL SYSTEM DIAGNOSIS ................................... DI10-177
DIAGNOSIS CHANGED BY
AFFECTED VIN
DI10-3
SCAN-I OPERATING PROCE-

DURES - XDi270 ENGINE
ENTERING DIAGNOSIS PROCEDURES .................... DI10-4
FUNCTION SELECTION ............................................. DI10-6

Check the trouble code .......................................... DI10-6
Sensor data check .................................................. DI10-7
Actuator check ........................................................ DI10-8
Trouble code clear ................................................ DI10-10
ECU identification .................................................. DI10-12
Injector coding (C2I) ............................................. DI10-13
Leak detection ...................................................... DI10-15
Variant coding ....................................................... DI10-16
ECU replace .......................................................... DI10-18
AFFECTED VIN
DI10-4
SCAN-I OPERATING PROCEDURES - D27DT ENGINE

ENTERING DIAGNOSIS PROCEDURES
1. Select “1] DIAGNOSIS” and press “ ” in “MAIN MENU”
screen.
Y220_10001
2. Select “5] REXTON” and press “ ” in “VEHICLE

SELECTION” screen.
Y220_10002
3. Select “1] ECU” and press “ ” in “CONTROL UNIT

Y220_10003
CHANGED BY DIAGNOSIS
AFFECTED VIN
DI10-5
4. Select “4] XDi 270” and press “ ” in “MODEL

Y220_10004
5. The “FUNCTION SELECTION” screen is displayed.
Y220_10005
AFFECTED VIN
DI10-6
FUNCTION SELECTION
Check the Trouble Code
Preceding work: Perform the “Entering Diagnosis Proce-
dures”
Y220_10006
1. Select “1] TROUBLE CODE” and press “ENTER” in

“FUNCTION SELECTION” screen.
Y220_10007
2. The “DIAGNOSTIC TROUBLE CODEs” screen is

displayed and it shows the trouble.
Note
If there is not any fault, “NO TROUBLE DETECTED”
message appears.
Y220_10008
3. When selecting a trouble code, then

if you press “ ”: Displays the sensor data for the
detected trouble (Freeze Frame
Mode).
if you press “ ”: Displays the help tips for the
detected trouble.
Y220_10013
AFFECTED VIN
DI10-7
Sensor Data Check

Preceding Work: Perform the “Entering Diagnosis Proce-
dures”
Y220_10010
1. Select “2] DATA LIST” and press “ ” in “FUNCTION

Y220_10011
2. The screen shows approx. 54 sensor data.
Y220_10012
3. Select the items you want to see and press “ ” key

to freeze them.
Note
You can freeze up to 5 items (*: selected items).
Y220_10013
AFFECTED VIN
DI10-8
Actuator Check
dures”
Y220_10014
1. Select “3] ACTUATOR” and press “ ” in “FUNCTION

Y220_10015
2. The screen shows 14 items. Select the item you want to

see and press “ ”.
Y220_10016
3. For example, if you select “02] GLOW PLUG” item and

press “ ”, the screen as shown in figure is displayed.
Y220_10017
AFFECTED VIN
DI10-9
4. If you want to operate the glow plug relay, press “ ”

key. The “OPERATING” message appears and the relay
operation alarm sounds.
Y220_10018
5. If you want to stop the operation press “ ” key in

keyboard.
Y220_10019
AFFECTED VIN
DI10-10
Trouble Code Clear

dures”
Y220_10020
1. Select “1] TROUBLE CODE” and press “ ” in

Y220_10021
2. The “DIAGNOSTIC TROUBLE CODEs” screen is

displayed and it shows the trouble.
Note
C = Current trouble, H = History trouble
Y220_10022
3. Fix the trouble and go back to “1] TROUBLE CODE”

screen and check if the trouble has been changed to “H
(History trouble code)” code.
Y220_10023
AFFECTED VIN
DI10-11
4. If the trouble has been change to “H (History trouble code)”

code, press “ ” key to go back to “FUNCTION
SELECTION” screen. In this screen, select “4] TROUBLE
CODE CLEAR” and press “ ”.
Y220_10024
5. The “TROUBLE CODE CLEAR” screen is displayed. If

you press “ ”, only the history trouble codes will be
cleared.
Note
• Current trouble codes will not be cleared.
• Check the trouble codes after clearing the trouble
codes.
Y220_10025
AFFECTED VIN
DI10-12
ECU Identification
dures”
Y220_10027
1. Select “1] ECU IDENTIFICATION” and press “ ” in

Y220_10028
2. The “ECU IDENTIFICATION” screen that shows the VIN,

ECU software number, ECU software version and
programming date is displayed.
Y220_10029
3. If you replaced the ECU, press “ ” to input the vehicle

identification number.
Y220_10030
AFFECTED VIN
DI10-13
Injector Coding (C2I)

dures”
Notice
If the injector/ECU has been replaced or the injector system

defective is suspected, go to C2I Coding item and check
the injector and coded injector C2I value.
Y220_10031
1. Select “6] INJECTOR (C2I) CORRECTIONS” and press

“ ” in “FUNCTION SELECTION” screen.
Y220_10032
2. The “INJECTOR (C2I) CORRECTIONS” screen that shows

current C2I coding values of #1 to #5 injector is displayed.
3. If you replaced the ECU, enter the C2I value of the relevant
injector.
Y220_10033
Note
• The C2I value of replacing injector is recorded in
the label.
• C2I coding number: 16 digits (ex, B1 B9 D4 1B 43
C6 0E 4F)
Y220_10034
AFFECTED VIN
DI10-14
3-1. If you enter the invalid C2I value of the relevant injector,
the message as shown in figure appears with alarm sound.
Note
If you want to go back to previous screen, press
“ ” key. You can see the previous C2I value.
Y220_10035
3-2. If you enter the valid C2I value of the relevant injector, the
message as shown in figure appears with alarm sound.
Y220_10036
AFFECTED VIN
DI10-15
Leak Detection
dures”
Note
This item is for checking the high fuel pressure after the
IMV supply line of HP pump in DI engine fuel system. If
you still suspect that the fuel pressure system is defective
even after no trouble is detected, perform the fuel pressure
test again by using a fuel pressure tool kit.
Y220_10037
1. Select “7] LEAK DETECTION” and press “ ” in

Y220_10038
2. The “LEAK DETECTION” screen that shows the checking

conditions as shown in figure is displayed.
Y220_10040
AFFECTED VIN
DI10-16
Variant Coding
dures”
Y220_10041
1. Select “8] VARIANT CODING” and press “ ” in

Y220_10042
2. When the “VARIANT CODING” screen is displayed,

select “1] READ VARIANT VALUE” and press “ ”.
Y220_10043
3. The “VARIANT CODING” screen that shows currently

equipped devices is displayed.
Y220_10044
AFFECTED VIN
DI10-17
4. If you need to change the variant coding, press “ ”

key to go back to “VARIANT CODING” screen. In the
screen, select “2] WRITE VARIANT CODING” and press
“ ”.
Y220_10045
5. When the “VARIANT CODING” screen is displayed,

change the item by using arrow keys.
Y220_10046
6. If you press “ ”, the message as shown in figure

appears. And, then “VARIANT CODING” screen is
displayed.
7. Select “READ VARIANT VALUE” to see the coding coded

value.
Y220_10047
AFFECTED VIN
DI10-18
ECU Replace
dures”
1. Select “9] ECU REPLACE” and press “ ” in
Y220_10048
2. When the “ECU REPLACE (STEP 2)” screen is displayed

followed by “ECU REPLACE (STEP 1) screen, turn the
ignition “OFF” and remove the currently installed ECU.
Notice
Do not turn off the Scan-100 at this time.
Record the below data:
- Vehicle identification number
- Variant coding value
- C2I coding value
Y220_10049 - Multi calibration
3. Install the new ECU.
Y220_10050
AFFECTED VIN
DI10-19
4. If you turn the ignition switch to “ON” position and press “ ”, the message as shown in figure 1 (system
initialization) appears, and then “MULTI CALIBRATION SELECTION” screen (fig. 2) is displayed.
figure 1 figure 2
Y220_10051
5. In “MULTI CALIBRATION SELECTION” screen, select “2]

DOM/GEN” for automatic transmission equipped vehicle
and select “4] DOM/GEN” for manual transmission
equipped vehicle.
Y220_10052
6. When you press “ ”, the processing message as

shown in figure appears.
Y220_10051A
AFFECTED VIN
DI10-20
7. If the multi calibration is completed successfully, “ECU

REPLACE (STEP 5) screen is displayed.
Backup data:
- Multi calibration value
- VIN value
- Variant code value
- Injector (C2I) value
Y220_10053
8. In immobilizer equipped vehicle, the immobilizer coding

should be done after completed the multi calibration.
Y220_10054
9. Press “ ” and enter the user password.
Y220_10055
10. If the password is invalid, the “access denied” screen as

shown in figure is displayed.
Y220_10056
AFFECTED VIN
DI10-21
11. If the password is valid, an immobilizer coding is started.
Y220_10057
12. If you want to code for additional keys, remove the first
key from key switch and insert the second key. Turn it
to “ON” position and press “ ” to proceed.
Y220_10058
13. You can code up to five keys with same manner.
14. When the immobilizer coding is completed, press “ ”.

The completion message as shown in figure appears.
Y220_10059
AFFECTED VIN
DI10-22
15. When you turn the ignition key to “OFF” position, the
message screen as shown in figure is displayed. Wait
for 15 seconds and turn the ignition key to “ON” position.
Y220_10060
16. Press “ ” to return to “MAIN MENU” screen.
Y220_10061
AFFECTED VIN
DI10-23
TROUBLE DIAGNOSIS TABLE
INDEX OF DTC ..................................................... 10D-24, 71

Trouble diagnosis table ......................................... 10D-27
Trouble diagnosis procedures ............................... 10D-75
AFFECTED VIN
DI10-24
INDEX OF DTC
P0102 Low HFM Sensor Signal (Circuit Open) .......... DI10-27 P0704 Clutch switch malfunction ............................. DI10-38
P0103 High HFM Sensor Signal (Circuit Short) .......... DI10-27 P1115 Coolant Temperature Sensor Malfunction ....... DI10-39
P0100 Air Mass Flow (HFM) Malfunction .................. DI10-28 P0118 Coolant Temperature Sensor
P0344 Cam Position Sensor Malfunction .................. DI10-28 Malfunction - Short ........................................ DI10-39
P0341 Cam Position Sensor Malfunction P0117 Coolant Temperature Sensor

(Poor Synchronization) .................................. DI10-28 Malfunction - Open ........................................ DI10-40
P0219 Too Small Clearance of Crank Angle Sensor .. DI10-28 P0115 Supply Voltage Fault to Coolant
P0336 Too Large Clearance of Crank Angle Sensor . DI10-29 Temperature Sensor ...................................... DI10-40
P0372 Crank Angle Sensor Malfunction .................... DI10-29 P0685 Main Relay Malfunction .................................. DI10-40
P1107 Barometric Sensor Circuit Short/GND Short ... DI10-29 P1405 EGR Solenoid Valve Short Malfunction - Short .. DI10-40
P1108 Barometric Sensor Circuit Short ..................... DI10-29 P1406 EGR Solenoid Valve Malfunction - Short ........ DI10-40
P1105 Barometric Sensor Circuit Short ..................... DI10-29 P1480 Condenser Fan #1 Circuit Malfunction - Open . DI10-41
P0562 Low Battery Voltage ...................................... DI10-30 P1481 Condenser Fan #1 Circuit Malfunction - Short . DI10-41
P0563 High Battery Voltage ...................................... DI10-30 P1482 Condenser Fan #1 Circuit Malfunction -
P0560 Battery Voltage Malfunction ........................... DI10-30 Short to Ground ............................................. DI10-41
P0109 Low Booster Pressure Sensor Signal ............ DI10-31 P1526 Condenser Fan #2 Circuit Malfunction - Open . DI10-41
P0106 High Booster Pressure Sensor Signal ............ DI10-31 P1527 Condenser Fan #2 Circuit Malfunction - Short . DI10-41
P0107 Booster Pressure Sensor Open/GND Short ... DI10-32 P1528 Condenser Fan #2 Circuit Malfunction -
P0108 Booster Pressure Sensor Short ..................... DI10-32 Short to Ground ............................................. DI10-41
P0105 Supply Voltage Fault to Booster P0325 Accelerometer #1 (Knock Sensor)

Pressure Sensor ............................................ DI10-33 Malfunction .................................................... DI10-42
P1106 Booster Pressure Sensor Malfunction ........... DI10-33 P0330 Accelerometer #2 (Knock Sensor)
P1109 Booster Pressure Sensor Initial Check Fault . DI10-34 Malfunction .................................................... DI10-42
P0571 Brake Pedal Switch Fault ............................... DI10-34 P1611 Injector Bank #1 Malfunction - Low Voltage ... DI10-42
P1572 Brake Lamp Signal Fault ................................. DI10-35 P1612 Injector Bank #1 Malfunction - High Voltage ... DI10-43
P1571 Brake Lamp Signal Fault ................................. DI10-35 P1618 Injector Bank #2 Malfunction - Low Voltage ... DI10-43
P1286 Low Resistance for Injector #1 wiring harness . DI10-35 P1619 Injector Bank #2 Malfunction - High Voltage .. DI10-43
P1287 High Resistance for Injector #1 wiring harness .. DI10-36 P0263 Injector #1 Balancing Fault ............................. DI10-44
P1288 Low Resistance for Injector #2 wiring harness . DI10-36 P0266 Injector #2 Balancing Fault ............................. DI10-44
P1292 Low Resistance for Injector #4 wiring harness . DI10-37 P0275 Injector #5 Balancing Fault ............................. DI10-44
P1294 Low Resistance for Injector #5 wiring harness . DI10-37 P0201 Injector #1 Circuit Open .................................. DI10-44
P1295 High Resistance for Injector #5 wiring harness .. DI10-38 P0202 Injector #2 Circuit Open ................................. DI10-44
P1290 Low Resistance for Injector #3 wiring harness . DI10-38 P0204 Injector #4 Circuit Open .................................. DI10-45
P1291 High Resistance for Injector #3 wiring harness .. DI10-38 P0205 Injector #5 Circuit Open .................................. DI10-45
AFFECTED VIN
DI10-25
P0203 Injector #3 Circuit Open .................................. DI10-45 P0110 Intake Air Temperature Circuit Malfunction -
P1201 Injector #1 Circuit Short .................................. DI10-45 Source Power Problem .................................. DI10-55
P1202 Injector #2 Circuit Short .................................. DI10-45 P1171 #1 Injector MDP Malfunction ........................... DI10-55
P0182 Fuel temperature sensor - Short to Ground ... DI10-46 P1173 #3 Injector MDP Malfunction ........................... DI10-55
P0183 Fuel temperature sensor - Short to B+ ........... DI10-46 P1252 Too High IMV Pressure ................................... DI10-56
P0180 Fuel temperature sensor - Malfunction .......... DI10-47 P1120 Accelerator Pedal Sensor #1 Malfunction ..... DI10-56
P1678 Glow Plug Malfunction - Open ...................... DI10-47 P1121 Accelerator Pedal Sensor #2 Malfunction ..... DI10-56
P1679 Glow Plug Malfunction - Short ...................... DI10-47 P1122 Accelerator Pedal Sensor Malfunction
P1680 Glow Plug Malfunction - Short to Ground ...... DI10-47 (Limp Home Mode) ......................................... DI10-56
P1530 #1 Heater operating circuit - Open ................ DI10-47 P1123 Accelerator Pedal Sensor Malfunction
P1531 #1 Heater operating circuit - Short ................ DI10-48 (Torque Mode) ............................................... DI10-57
P1532 #1 Heater operating circuit - Short to Ground . DI10-48 P1124 Accelerator Pedal Sensor Malfunction - Stuck .. DI10-57
P1534 #2 Heater operating circuit - Open ................ DI10-48 P0122 Accelerator Pedal Sensor #1 Malfunction -
P1535 #2 Heater operating circuit - Short ................. DI10-48 Open .............................................................. DI10-57
P1536 #2 Heater operating circuit - Short to Ground DI10-48 P0123 Accelerator Pedal Sensor #1 Malfunction -
P1254 Maximum Rail Pressure Control Malfunction Short .............................................................. DI10-57
(IMV Fault) .................................................... DI10-49 P0120 Accelerator Pedal Sensor #1 Malfunction -
P1253 Minimum Rail Pressure Control Malfunction Supply Voltage Fault ...................................... DI10-57
(IMV Fault) .................................................... DI10-49 P0222 Accelerator Pedal Sensor #2 Malfunction -
P1256 Too Small Transfer Pressure Fuel in Open .............................................................. DI10-58

Rail Pressure System ..................................... DI10-50 P0223 Accelerator Pedal Sensor #2 Malfunction -
P1257 Too Large Transfer Pressure Fuel in Short .............................................................. DI10-58
Rail Pressure System ..................................... DI10-50 P0220 Accelerator Pedal Sensor #2 Malfunction -
P1258 Too Small High Pressure Fuel in Supply Voltage Fault ...................................... DI10-58
Rail Pressure System .................................... DI10-51 P0192 Fuel Rail Pressure Sensor Malfunction - Open .. DI10-58
P1259 Too Large High Pressure Fuel in P0193 Fuel Rail Pressure Sensor Malfunction - Short .. DI10-59
Rail Pressure System .................................... DI10-51 P0190 Supply Voltage Fault to
P1191 Pressure Build Up - Too Slow ....................... DI10-52 Fuel Rail Pressure Sensor .............................. DI10-59
P0255 IMV Driver Circuit Malfunction - Open ........... DI10-52 P0191 Fuel Rail Pressure Sensor Signal Fault .......... DI10-59
P0251 IMV Driver Circuit Malfunction - Short ........... DI10-52 P1192 Fuel Rail Pressure Sensor Initial Signal Fault -
P0253 IMV Driver Circuit Malfunction - Low ............................................................... DI10-60
Short to Ground ............................................ DI10-52 P1193 Fuel Rail Pressure Sensor Initial Signal Fault -
P0113 Intake Air Temperature Circuit Malfunction - High ............................................................... DI10-60
Short .............................................................. DI10-53 P1190 Fuel Rail Pressure Sensor Initial Signal Fault .. DI10-60
P0112 Intake Air Temperature Circuit Malfunction - P0215 Main Relay Fault - Stuck ................................. DI10-61
Open ............................................................. DI10-54 P1500 Vehicle Speed Fault ....................................... DI10-61
P0642 ECU Supply Voltage 1 Fault - Low (5 V) ........ DI10-61
AFFECTED VIN
DI10-26
P0643 ECU Supply Voltage 1 Fault - High (5 V) ........ DI10-61 P1672 #2 Glow Plug Fault - Short (B+) ..................... DI10-67
P0641 ECU Supply Voltage 1 Fault (5 V) ................... DI10-61 P1673 #3 Glow Plug Fault - Short (B+) ..................... DI10-67
P0652 ECU Supply Voltage 2 Fault - Low (5 V) ........ DI10-62 P1674 #4 Glow Plug Fault - Short (B+) ..................... DI10-67
P0653 ECU Supply Voltage 2 Fault - High (5 V) ........ DI10-62 P1675 #5 Glow Plug Fault - Short (B+) ..................... DI10-67
P0651 ECU Supply Voltage 2 Fault (5 V) ................... DI10-62 P0700 TCU Signal Fault ............................................. DI10-67
P0698 ECU Supply Voltage Fault - Low (2.5 V) ........ DI10-62 P1540 Air Conditioner Operating Circuit Fault - Open . DI10-67
P0699 ECU Supply Voltage Fault - High (2.5 V) ........ DI10-62 P1541 Air Conditioner Operating Circuit Fault - Short . DI10-67
P0697 ECU Supply Voltage Fault (2.5 V) ................... DI10-63 P1542 Air Conditioner Operating Circuit Fault -
P0245 Turbo Charger Actuator Circuit Fault - Short .. DI10-63 Short to Ground ............................................. DI10-67
P0246 Turbo Charger Actuator Circuit Fault - P1149 Too High Water Level in Fuel Filter ................. DI10-68
Short to B+ ..................................................... DI10-63 P1634 Immobilizer Fault (refer to immobilizer section) .. DI10-68
P0606 ECU Watchdog Fault ...................................... DI10-63 P1635 No response from Immobilizer
P1607 ECU Injector Cut Fault ..................................... DI10-63 (refer to immobilizer section) ......................... DI10-68
P1600 ECU Shut Down Fault ..................................... DI10-63 P1630 Wrong response from Immobilizer
P1601 ECU Fault ....................................................... DI10-63 (refer to immobilizer section) ......................... DI10-68
P1602 ECU Fault ....................................................... DI10-63 P1631 Immobilizer Fault (refer to immobilizer section) . DI10-68
P1614 ECU C2I/MDP Fault ......................................... DI10-64 P1632 Immobilizer Fault (refer to immobilizer section) . DI10-68
P1620 ECU Fault ....................................................... DI10-64
P1621 ECU Fault ....................................................... DI10-64
P1622 ECU Fault ....................................................... DI10-64
P1603 ECU Fault ....................................................... DI10-64
P1604 ECU Fault ....................................................... DI10-64
P1605 ECU Fault ....................................................... DI10-64
P1148 Accelerometer (Knock Sensor) Learning Fault . DI10-64
P0400 EGR Control Valve Fault ................................. DI10-65
P1235 VGT Operation Fault ...................................... DI10-65
P1608 ECU Fault ....................................................... DI10-65
P0335 No Crank Signals ............................................ DI10-65
P1170 Torque Trim Fault - High ................................. DI10-65
P1676 Glow Plug Communication Fault ..................... DI10-65
P1677 Glow Plug Controller Fault .............................. DI10-65
P0671 #1 Glow Plug Fault - Open ............................. DI10-66
P1671 #1 Glow Plug Fault - Short (+B) ..................... DI10-66
AFFECTED VIN
DI10-27
TROUBLE DIAGNOSIS TABLE

Torque Torque Delayed Immediately Limp
DTC Trouble Help Reduction Reduction Engine Engine Home
(max.50%) (max.20%) Stop Stop Mode
P0102 Low HFM Sensor Signal - HFM sensing values are lower than
(Circuit Open) minimum sensing values.
- Check the resistance in HFM sensor.
- Check the ECU wiring harness (open
and poor contact).
• Check the ECU pin #82 and #84 for
open circuit.
- Actual air mass flow vs. Output
voltages.
• -20 Kg/h: 0.47 V
• 0 Kg/h: 0.99 V
• 10 Kg/h: 1.2226 ~ 1.2398 V
• 15 Kg/h: 1.3552 ~ 1.3778 V
• 30 Kg/h: 1.6783 ~ 1.7146 V
• 60 Kg/h: 2.1619 ~ 2.2057 V
• 120 Kg/h: 2.7215 ~ 2.7762 V
• 250 Kg/h: 3.4388 ~ 3.5037 V
• 370 Kg/h: 3.8796 ~ 3.9511 V
• 480 Kg/h: 4.1945 ~ 4.2683 V
• 640 Kg/h: 4.5667 ~ 4.6469 V
- Replace the ECU if required.
P0103 High HFM Sensor Signal - HFM sensing values are higher than
(Circuit Short) maximum sensing values.
- Check the resistance in HFM sensor.
- Check the ECU wiring harness (open
and poor contact).
open circuit.
voltages.
• -20 Kg/h: 0.47 V
• 0 Kg/h: 0.99 V
• 10 Kg/h: 1.2226 ~ 1.2398 V
• 15 Kg/h: 1.3552 ~ 1.3778 V
• 30 Kg/h: 1.6783 ~ 1.7146 V
• 60 Kg/h: 2.1619 ~ 2.2057 V
• 120 Kg/h: 2.7215 ~ 2.7762 V
• 250 Kg/h: 3.4388 ~ 3.5037 V
• 370 Kg/h: 3.8796 ~ 3.9511 V
• 480 Kg/h: 4.1945 ~ 4.2683 V
• 640 Kg/h: 4.5667 ~ 4.6469 V
AFFECTED VIN
DI10-28

P0100 Air Mass Flow (HFM) Mal- - The external power supply is faulty.
function • Check the external power supply.
• Check the sensor wiring harness
(open, short, poor contact).
voltages.
• -20 Kg/h: 0.47 V
• 0 Kg/h: 0.99 V
• 10 Kg/h: 1.2226 ~ 1.2398 V
• 15 Kg/h: 1.3552 ~ 1.3778 V
• 30 Kg/h: 1.6783 ~ 1.7146 V
• 60 Kg/h: 2.1619 ~ 2.2057 V
• 120 Kg/h: 2.7215 ~ 2.7762 V
• 250 Kg/h: 3.4388 ~ 3.5037 V
• 370 Kg/h: 3.8796 ~ 3.9511 V
• 480 Kg/h: 4.1945 ~ 4.2683 V
• 640 Kg/h: 4.5667 ~ 4.6469 V
P0344 Cam Position Sensor Mal- - No cam recognition signal (missing
function events).
- Check the source voltage of cam posi-
tion sensor (ECU pin #111) (specified
value: 4.5 ~ 12 V).
- Check the sensor wiring harness for
ECU pin #103 and #104 (open, short,
poor contact).
- Check the cam position sensor.
- Measure the air gap: 0.2 ~ 1.8 mm
P0341 Cam Position Sensor Malfunc- - Not synchronized with Crank angle
tion (Poor Synchronization) signal.
- Check the source voltage of cam posi-
tion sensor (specified value: 4.5 ~ 12 V).
ECU pin #103 and #104 (open, short,
poor contact).
- Check the cam position sensor.
P0219 Too Small Clearance of - Crank angle signal faults or clearance
Crank Angle Sensor too close.
ECU pin #90 and #82 (open, short, poor
contact).
- Check the resistance of crank angle
sensor: 1090 Ω ± 15 %.
• 1.3 mm of air gap: outputs 1.0 V at
40 rpm
• 0.3 mm of air gap: outputs 150 V at
7000 rpm
- Check the teeth condition.
• Drive plate (A/T), DMF (M/T)
AFFECTED VIN
DI10-29

P0336 Too Large Clearance of - Air gap of crank angle sensor is
Crank Angle Sensor abnormal.
contact).
sensor: 1090 Ω ± 15 %.
40 rpm
7000 rpm
P0372 Crank Angle Sensor Mal- - Even though cam position recognition
function is normal, no crank angle signal recog-
nition (missing tooth).
contact).
sensor: 1090 Ω ± 15 %.
40 rpm
7000 rpm
P1107 Barometric Sensor Circuit - Out of range about barometric sensor
Short/GND Short (short to ground).
- Actual barometric pressure vs. Output
voltages.
• 15 Kpa: 0 V 35 Kpa: 1.0 V
• 55 Kpa: 2.0 V 80 Kpa: 3.0 V
• 100 Kpa: 4.0 V 110 Kpa: 4.5 V
- Replace the ECU.
Short (short to B+).
voltages.
• 15 Kpa: 0 V 35 Kpa: 1.0 V
• 55 Kpa: 2.0 V 80 Kpa: 3.0 V
• 100 Kpa: 4.0 V 110 Kpa: 4.5 V
- Replace the ECU.
Short (over voltage).
voltages.
• 15 Kpa: 0 V 35 Kpa: 1.0 V
• 55 Kpa: 2.0 V 80 Kpa: 3.0 V
• 100 Kpa: 4.0 V 110 Kpa: 4.5 V
- Replace the ECU.
AFFECTED VIN
DI10-30

P0562 Low Battery Voltage - Malfunction in recognition of system O
source voltage (Lower than threshold).
• Less than minimum 8 Volts in 2000
rpm below
• Less than 10 Volts in 2000 rpm above.
- Check the battery wiring harness for
ECU pin #3, #4 and #5 (open, short,
poor contact).
- Check the battery main relay and fuse.
- Check the body ground.
- Measure the resistance between body
ground and ECU ground.
• Repair the ECU ground if the resis-
tance is high.
P0563 High Battery Voltage - Malfunction in recognition of system O
source voltage (Higher than threshold).
• More than minimum 16 Volts in 2000
rpm below
poor contact).
- Check the alternator.
tance is high.
P0560 Battery Voltage Malfunc- - Malfunction in recognition of system O
tion source voltage (A/D converter faults).
• Less than minimum 8 Volts in 2000
rpm below
• Less than 10 Volts in 2000 rpm above.
poor contact).
- Check the battery main relay and fuse.
tance is high.
AFFECTED VIN
DI10-31

P0109 Low Booster Pressure - Out of signal range about boost pres-
Sensor Signal sure sensor at Ignition key-On and En-
gine Stop (Lower than specified values).
- Check the supply voltage to sensor.
- Actual boost pressure vs. Output
voltages.
• Raw Signal Range: 0.545 ~ 2.490 bar
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
- Check the sensor wiring harness for ECU
pin #99 and #100 (open, poor contact).
- Visually check sensor and replace if
required.
- Check whether existing or not about
turbo boosting control malfunction
(P1235) simultaneously.
- If there is turbo boost control fault,
Should be checked followings also;
• Leakage before turbo system
• Vacuum pump malfunction
• Waste gate’ solenoid valve
• Turbo charger system defect or mal-
function itself
• Air inlet restriction
• Exhaust system restriction
P0106 High Booster Pressure - Out of signal range about boost pres-
Sensor Signal sure sensor at Ignition key-On and En-
gine Stop (Higher than specified
values).
- Actual boost pressure vs. Output
voltages.
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
ECU pin #99 and #100 (open, poor
contact).
required.
• Turbo charger system defect or
malfunction itself
AFFECTED VIN
DI10-32

P0107 Booster Pressure Sensor - Out of signal range about boost pres-
Open/GND Short sure sensor at Engine running condi-
tion (Lower than specified values).
- Actual boost pressure vs. Output volt-
ages
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
contact).
required.
function itself
P0108 Booster Pressure Sensor - Out of signal range about boost pres-
Short sure sensor at Engine running condi-
tion (Higher than specified values).
ages
• Raw Signal Range: 0.545~2.490 bar
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
contact).
required.
malfunction itself
AFFECTED VIN
DI10-33

P0105 Supply Voltage Fault to - Out of range of supply voltages about
Booster Pressure Sensor boost pressure sensor at Ignition key-
On and Engine Stop (Higher than speci-
fied values).
- Actual boost pressure vs. Output voltages
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
contact).
required.
function itself
P1106 Booster Pressure Sensor - Out of range of supply voltages about
Malfunction boost pressure sensor at Ignition key-
On and Engine Stop (Higher than speci-
fied values).
- Actual boost pressure vs. Output voltages.
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
contact).
required.
malfunction itself
AFFECTED VIN
DI10-34

P1109 Booster Pressure Sensor - Implausible signal values or range about
Initial Check Fault boost pressure sensor at Engine run-
ning condition (Higher than specified
values).
ages
• 0.4 bar: 0.6120 V
• 1.4 bar: 2.6520 V
• 2.4 bar: 4.6920 V
contact).
required.
function itself
P0571 Brake Pedal Switch Fault - The brake pedal switch or light switch
is faulty.
• Brake pedal switch: Normal Close
(NC)
• Light switch: Normal Open (NO)
• When operating the brake switch,
one signal (NO) is sent to auto
cruise and the other (NC) is sent to
brake lamp.
- Check the brake and light switch wir-
ing harness.
- Check the supply voltage to brake and
light switch (12 V).
- Check the brake and light switch for
contact.
- Check the ECU wiring harness for ECU
pin #77 and #58 (short, poor contact).
AFFECTED VIN
DI10-35

P1572 Brake Lamp Signal Fault - The brake pedal switch or light switch
is faulty.
(NC)
• When operating the brake pedal
switch, one signal (NO) is sent to
auto cruise and the other (NC) is
sent to brake lamp.
- Check the brake pedal and light switch
wiring harness.
- Check the supply voltage to brake pedal
and light switch (12 V).
- Check the brake pedal and light switch
for contact.
pin #58 (open, short, poor contact).
P1571 Brake Lamp Signal Fault - The brake pedal switch is faulty.
(NC)
• When operating the brake pedal
switch, one signal (NO) is sent to
auto cruise and the other (NC) is
sent to brake lamp.
- Check the brake pedal switch wiring
harness.
- Check the supply voltage to brake pedal
switch (12 V).
- Check the brake pedal switch for
contact.
pin #77 (open, short, poor contact).
P1286 Low Resistance for Injec- - Out of range about wiring harness re-
tor #1 wiring harness sistance for Injector #1.
• Low: Less than 0.150 Ω (injector
circuit open)
- Check the injector #1 wiring harness
and electric isolation.
for open circuit.
• If the pin in injector #1 is defective,
replace injector #1 and perform C2I
coding, then check again.
• If the pin in injector #1 is not
defective, check the ECU wiring
harness.
AFFECTED VIN
DI10-36

P1287 High Resistance for Injec- - Out of range about wiring harness re-
• High: More than 0.573 Ω (injector
circuit short)
for short circuit.
• If the trouble still exists after remov-
ing the injector connector, replace
injector #1 and perform C2I coding,
then check again.
• If the trouble is fixed after removing
the injector connector, check the
wiring harness between ECU and
injector.
circuit open)
for open circuit.
harness.
circuit short)
for short circuit.
then check again.
injector.
AFFECTED VIN
DI10-37

circuit open)
for open circuit.
harness.
circuit short)
for short circuit.
then check again.
injector.
circuit open)
for open circuit.
harness.
AFFECTED VIN
DI10-38

circuit short)
for short circuit.
then check again.
injector.
circuit open)
for open circuit.
harness.
circuit short)
for short circuit.
then check again.
injector.
P0704 Clutch switch malfunction - The clutch switch is faulty (Manual
Transmission Only).
- Check the switch wiring harness.
• Check the ECU pin #38 for open,
short and poor contact.
- Check the switch supply voltage and
operations.
AFFECTED VIN
DI10-39

P1115 Coolant Temperature Sen- - Implausible values of coolant tempera-
sor Malfunction ture (If the temperature is below the
limits values after warm up).
- If Fuel temperature is invalid, the previ-
ous coolant temperature is retained.
- Actual air temp. vs. Resistance
• 20°C: 2449 Ω
• 50°C: 826.3 Ω
• 80°C: 321.4 Ω
• 100°C: 112.9 Ω
- Check the wiring harness (open, short
and poor contact).
• ECU pin #101 and #102
- Visually check the sensor and replace
if required.
- Check the thermostat, water pump ra-
diator related coolant route (thermostat
stuck).
P0118 Coolant Temperature Sen- - Malfunction in recognition of coolant
sor Malfunction - Short temperature
• More than maximum values (Circuit
Short)
• External power supply malfunction
• 20°C: 2449 Ω
• 50°C: 826.3 Ω
• 80°C: 321.4 Ω
• 100°C: 112.9 Ω
- Check the wiring harness (short and
poor contact).
• ECU pin #101 and #102
if required.
AFFECTED VIN
DI10-40

P0117 Coolant Temperature Sen- - Malfunction in recognition of coolant
sor Malfunction - Open temperature
• Less than minimum values (Circuit
Open)
• External power supply malfunction
• 20°C: 2449 Ω
• 50°C: 826.3 Ω
• 80°C: 321.4 Ω
• 100°C: 112.9 Ω
- Check the wiring harness (open and
poor contact).
• ECU pin #101 and #102
if required.
P0115 Supply Voltage Fault to - Check if the supply voltage of approx.
Coolant Temperature Sen- 12 V is applied.
sor
P0685 Main Relay Malfunction - The the main relay is unexpectedly
high/low state (ECU is supplied after 3
seconds).
- Relay resistance: 92 ± 9 Ω (at 20°C)
- Check the relay wiring harness (open,
short and poor contact).
• Check for open and short: ECU pin #9.
- If the forced operation is not available,
replace the ECU.
P1405 EGR Solenoid Valve - Out of range about EGR gas: High.
Malfunction - Short to • EGR controller circuit: Open or short
ground to ground
- Check the EGR actuator wiring harness.
- Check the supply voltage to EGR sole-
noid valve.
- Check the EGR solenoid valve.
- Check the EGR valve for stick.
- Check the resistance of EGR actuator:
15.4 Ω.
- Check the ECU wiring harness for open
and short.
• ECU pin #96
P1406 EGR Solenoid Valve - Out of range about EGR gas: Low.
Malfunction - Short to • EGR controller circuit: Short to battery
+Batt
noid valve.
- Check the EGR solenoid valve.
- Check the EGR valve for stick.
- Check the resistance of EGR actuator:
15.4 Ω
and short.
• ECU pin #96
AFFECTED VIN
DI10-41

P1480 Condenser Fan #1 Circuit - Condenser fan #1: Open
Malfunction - Open - Check the relay and relay wiring
harness.
and short.
• ECU pin #80
- If the forced operation is not available
after replacing the relay, replace the
ECU.
P1481 Condenser Fan #1 Circuit - Condenser fan #1: Short
Malfunction - Short - Check the relay and relay wiring
harness.
and short.
• ECU pin #80
ECU.
P1482 Condenser Fan #1 Circuit - Condenser fan #1: Short to ground.
Malfunction - Short to Ground - Check the relay and relay wiring
harness.
and short.
• ECU pin #80
ECU.
P1526 Condenser Fan #2 Circuit - Condenser fan #2: Open
Malfunction - Open - Check the relay and relay wiring
harness.
and short.
• ECU pin #81
ECU.
P1527 Condenser Fan #2 Circuit - Condenser fan #2: Short
Malfunction - Short - Check the relay and relay wiring
harness.
and short.
• ECU pin #81
ECU.
P1528 Condenser Fan #2 Circuit - Condenser fan #2: Short to ground
Malfunction - Short to Ground - Check the relay and relay wiring
harness.
and short.
• ECU pin #81
ECU.
AFFECTED VIN
DI10-42

P0325 Accelerometer #1 (Knock - The signal / noise ratio is too low about
Sensor) Malfunction accelerometer # 1.
- Check the accelerometer wiring har-
ness and tightening torque.
• Tightening torque: 20 ± 5 Nm
and short.
• ECU pin #45 and #46
- If the trouble still exists even after re-
placing the accelerometer, replace the
ECU.
P0330 Accelerometer #2 (Knock - The signal / noise ratio is too low about
Sensor) Malfunction accelerometer # 1.
- Check the accelerometer wiring har-
ness and tightening torque.
• Tightening torque: 20 ± 5 Nm
and short.
- If the trouble still exists even after re-
placing the accelerometer, replace the
ECU.
P1611 Injector Bank #1 Malfunc- - Malfunction of injector (#1, #4, #3) cir-
tion - Low Voltage cuit (Low): Short to Ground or to
Battery.
- Operating voltage: 6 ~ 18 V
- Check the injector bank #1: Open and
poor contact
- Check if the trouble recurs with the
injectors removed and the ignition key
“OFF”.
• If recurred, check the injector and
ECU wiring harness.
- Check if the trouble recurs while in-
stalling the injectors one by one with
the ignition key “ON”.
• If recurred, replace the injector (perform
C2I coding after replacement).
• Check the other injectors with same
manner.
- Check the ECU wiring harness.
AFFECTED VIN
DI10-43

P1612 Injector Bank #1 Malfunc- - Malfunction of injector (#1, #4, #3) cir-
tion - High Voltage cuit (High): Short to Ground or to Battery.
- Check the injector bank #1: Short and
poor contact
- Check if the trouble recurs with the injec-
tors removed and the ignition key “OFF”.
ECU wiring harness.
manner.
P1618 Injector Bank #2 Malfunc- - Malfunction of injector (#2, #5) circuit
tion - Low Voltage (Low): Short to Ground or to Battery.
- Check the injector bank #2: Open and
poor contact
ECU wiring harness.
manner.
P1619 Injector Bank #2 Malfunc- - Malfunction of injector (#2, #5) circuit
tion - High Voltage (High): Short to Ground or to Battery.
- Check the injector bank #2: Short and
poor contact
ECU wiring harness.
manner.
AFFECTED VIN
DI10-44

P0263 Injector #1 Balancing Fault - Injector #1 cylinder balancing faults
(Injector stuck closed).
- Check the injector circuit for open.
- Check the glow plug.
- Check the inlet tube for clogging.
- Check the EGR.
- Replace the ECU if required (perform
- Check the EGR.
- Check the EGR.
- Check the EGR.
- Check the EGR.
P0201 Injector #1 Circuit Open - Injector #1 circuit malfunction: Open.
• If the injector pin is defective, per-
form C2I coding and check again.
• If the injector pin is normal, check
the ECU wiring harness (ECU pin:
#117, #114).
#118, #121).
AFFECTED VIN
DI10-45

#117, #115).
#118, #120).
#117, #116).
P1201 Injector #1 Circuit Short - Injector #1 circuit malfunction: Short.
• If the trouble recurs with the injec-
tor removed, replace the injector.
Perform C2I coding and check
again.
• If the trouble does not recur, check
the wiring harness between the in-
jector and ECU (ECU pin: #117, #114).
again.
again.
again.
AFFECTED VIN
DI10-46

again.
P0182 Fuel temperature sensor - - The sensing values are higher than
Short to Ground specified values for fuel temperature
sensor. (More than maximum sensing
values 140°C - Circuit Short)
- Actual fuel temp. vs. Resistance
• -40°C: 75.780 Ω -20°C: 21.873 Ω
• -10°C: 12.462 Ω 0°C: 7.355 Ω
• 10°C: 4.481 Ω 20°C: 2.812 Ω
• 25°C: 2.252 Ω 30°C: 1.814 Ω
• 40°C: 1.199 Ω 50°C: 0.811 Ω
• 70°C: 0.394 Ω 90°C: 0.206 Ω
• 120°C: 0.087 Ω
- Recovery values when fuel tempera-
ture sensor failure: 95°C
- Check the wiring harness for open,
• ECU pin: #109, #110
- Check the ECU wiring and replace the
ECU if required.
P0183 Fuel temperature sensor - - The sensing values are lower than
Short to B+ specified values for fuel temperature
sensor. (Less than maximum sensing
values - 40°C - Circuit Open)
• -40°C: 75.780 Ω -20°C: 21.873 Ω
• -10°C: 12.462 Ω 0°C: 7.355 Ω
• 10°C: 4.481 Ω 20°C: 2.812 Ω
• 25°C: 2.252 Ω 30°C: 1.814 Ω
• 40°C: 1.199 Ω 50°C: 0.811 Ω
• 70°C: 0.394 Ω 90°C: 0.206 Ω
• 120°C: 0.087 Ω
• ECU pin: #109, #110
ECU if required.
AFFECTED VIN
DI10-47

P0180 Fuel temperature sensor - - The power source circuit is faulty for
Malfunction fuel temperature sensor. (Fuel tem-
perature sensor is mounted in high
pressure pump)
• -40°C: 75.780 Ω -20°C: 21.873 Ω
• -10°C: 12.462 Ω 0°C: 7.355 Ω
• 10°C: 4.481 Ω 20°C: 2.812 Ω
• 25°C: 2.252 Ω 30°C: 1.814 Ω
• 40°C: 1.199 Ω 50°C: 0.811 Ω
• 70°C: 0.394 Ω 90°C: 0.206 Ω
• 120°C: 0.087 Ω
• ECU pin: #109, #110
ECU if required.
P1678 Glow Plug Malfunction - - Glow plug circuit malfunction: Open.
Open - Check the glow plug wiring harness
for open.
• ECU pin #113
- Check the glow plug relay operations.
- Check the glow plug power supply.
ECU if required.
P1679 Glow Plug Malfunction - - Glow plug circuit malfunction: Short.
Short - Check the glow plug wiring harness
for open.
• ECU pin #113
ECU if required.
P1680 Glow Plug Malfunction - - Glow plug circuit malfunction: Short to
Short to Ground ground.
- Check the glow plug wiring harness
for open.
• ECU pin #113
ECU if required.
P1530 #1 Heater operating circuit - #1 heater circuit malfunction: Open.
- Open - Check the wiring harness for open.
• ECU pin #61
- Check the heater relay operations.
replace the ECU.
ECU if required.
AFFECTED VIN
DI10-48

P1531 #1 Heater operating circuit - #1 heater circuit malfunction: Short.
- Short - Check the wiring harness for short.
• ECU pin #61
replace the ECU.
ECU if required.
P1532 #1 Heater operating circuit - #1 heater circuit malfunction: Short to
- Short to Ground ground.
- Check the wiring harness for short.
• ECU pin #61
replace the ECU.
ECU if required.
P1534 #2 Heater operating circuit - #2 heater circuit malfunction: Open.
- Open - Check the wiring harness for open.
• ECU pin #62
replace the ECU.
ECU if required.
P1535 #2 Heater operating circuit - #2 heater circuit malfunction: Short.
- Short - Check the wiring harness for short.
• ECU pin #62
replace the ECU.
ECU if required.
P1536 #2 Heater operating circuit - #2 heater circuit malfunction: Short to
- Short to Ground ground.
- Check the wiring harness for short.
• ECU pin #62
replace the ECU.
ECU if required.
AFFECTED VIN
DI10-49

P1254 Maximum Rail Pressure - Rail pressure faults: Too high
Control Malfunction (IMV - Check the IMV wiring harness.
Fault)
• Check the ECU pin #87 for open and
short.
- Check the high pressure fuel lines, fuel
rails and high pressure pipes for leaks.
- Check the rail pressure sensor.
• Supply voltage: 5 ± 0.1 V
• Output voltage at 1600 bar: 4.055 ±
0.125 V
• Output voltage at atmospheric
pressure: 0.5 ± 0.04 V
- Check the transfer pressure fuel pres-
sure lines.
• Check the fuel level in fuel tank.
Check the fuel system for air influx.
• Check the fuel filter specification.
- Check the IMV resistance: 5.44 Ω
• When out of specified value: replace
high pressure pump and IMV
P1253 Minimum Rail Pressure - Rail pressure faults: Too low
Control Malfunction (IMV - Check the IMV wiring harness.
Fault)
short.
- Check the high pressure fuel lines, fuel
rails and high pressure pipes for leaks.
0.125 V
sure lines.
AFFECTED VIN
DI10-50

P1256 Too Small Transfer Pres- - Rail pressure fault: IMV current trim too
sure Fuel in Rail Pressure high, drift.
System - Check the IMV wiring harness.
short.
0.125 V
sure lines.
- Check the high pressure fuel system.
• Check the fuel rails and high pres-
sure pipes for leaks.
P1257 Too Large Transfer Pres- - Rail pressure fault: IMV current trim too
sure Fuel in Rail Pressure high, drift.
System - Check the IMV wiring harness.
short.
0.125 V
sure lines.
AFFECTED VIN
DI10-51

P1258 Too Small High Pressure - Rail pressure fault: IMV current trim too
Fuel in Rail Pressure Sys- high, drift.
tem - Check the IMV wiring harness.
short.
0.125V
- Check the transfer pressure fuel lines.
P1259 Too Large High Pressure - Rail pressure fault: IMV current trim too
Fuel in Rail Pressure Sys- high, drift.
tem - Check the IMV wiring harness.
short.
0.125 V
AFFECTED VIN
DI10-52

P1191 Pressure Build Up - Too - The pressure build up during cranking
Slow is too slow.
- Check the IMV wiring harness.
short.
0.125 V
P0255 IMV Driver Circuit Malfunc- - IMV driver circuit malfunction: Open O O
tion - Open - Check the IMV wiring harness.
• Check the ECU pin #87 for open.
- Check the IMV resistance.
P0251 IMV Driver Circuit Malfunc- - IMV driver circuit malfunction: Short O O
tion - Short - Check the IMV wiring harness.
• Check the ECU pin #87 for short.
P0253 IMV Driver Circuit Malfunc- - IMV driver circuit malfunction: Short to O O
tion - Short to Ground ground
• Check the ECU pin #87 for short to
ground.
AFFECTED VIN
DI10-53

P0113 Intake Air Temperature Cir- - The intake air temperature sensing
cuit Malfunction - Short value is lower than maximum value of
150°C: Open
• Actual air temperature vs. Voltages
• 20°C: 2.65 Ω
• 30°C: 2.18 Ω
• 50°C: 1.40 Ω
• Recovery values when intake air
temperature sensor failure: 50°C
- Check the sensor wiring harness.
• Check the source power circuit for
short to ground.
- Check the sensor resistance.
• Actual air temperature vs. Resis-
tance
• -40°C: 39.260 Ω
• -20°C: 13.850 Ω
• 0°C: 5.499 Ω
• 20°C: 2.420 Ω
• 40°C: 1.166 Ω
• 60°C: 0.609 Ω
• 80°C: 0.340 Ω
• 100°C: 0.202 Ω
• 120°C: 0.127 Ω
open.
AFFECTED VIN
DI10-54

cuit Malfunction - Open value is lower than maximum value of
150°C: Open
• 20°C: 2.65 Ω
• 30°C: 2.18 Ω
• 50°C: 1.40 Ω
short to ground.
tance
• -40°C: 39.260 Ω
• -20°C: 13.850 Ω
• 0°C: 5.499 Ω
• 20°C: 2.420 Ω
• 40°C: 1.166 Ω
• 60°C: 0.609 Ω
• 80°C: 0.340 Ω
• 100°C: 0.202 Ω
• 120°C: 0.127 Ω
open.
AFFECTED VIN
DI10-55

cuit Malfunction - Source value is lower than minimum value or
Power Problem higher than maximum value, or the ex-
ternal power to HFM sensor is faulty.
• 20°C: 2.65 Ω
• 30°C: 2.18 Ω
• 50°C: 1.40 Ω
short to ground.
tance
• -40°C: 39.260 Ω
• -20°C: 13.850 Ω
• 0°C: 5.499 Ω
• 20°C: 2.420 Ω
• 40°C: 1.166 Ω
• 60°C: 0.609 Ω
• 80°C: 0.340 Ω
• 100°C: 0.202 Ω
• 120°C: 0.127 Ω
open and short.
P1171 #1 Injector MDP Malfunction - The #1 injector MDP is faulty.
- Replace the injector and perform C2I
coding again.
coding again.
coding again.
coding again.
coding again.
AFFECTED VIN
DI10-56

P1252 Too High IMV Pressure - The rail pressure is excessively high.
short.
0.125 V
P1120 Accelerator Pedal Sensor - The potentiometer 1 is not plausible O
#1 Malfunction with potentiometer 2.
- Check the wiring harness.
• Check the ECU pin #72, 53 and #32,
14 for open and short.
- Check the accelerator pedal module.
P1121 Accelerator Pedal Sensor - The potentiometer 1 is not plausible O
#2 Malfunction with potentiometer 2.
• Check the ECU pin #72, 53 and #32,
14 for open and short.
P1122 Accelerator Pedal Sensor - When triggering limp home mode.
Malfunction (Limp Home - Check the supply voltage to sensor.
Mode)
• Check the ECU pin #72, 71, 53 and
#57, 32, 14 for open and short.
AFFECTED VIN
DI10-57

P1123 Accelerator Pedal Sensor - When triggering reduced torque mode. O
Malfunction (Torque Mode) - Check the supply voltage to sensor.
• Check the ECU pin #72, 71, 53 and
#57, 32, 14 for open and short.
- Replace the ECU if required
P1124 Accelerator Pedal Sensor - The accelerator pedal sensor is stuck. O
Malfunction - Stuck - Check the brake switch wiring harness
and operations.
- Check the accelerator pedal operations.
P0122 Accelerator Pedal Sensor - Out of range about potentiometer 1 of O
#1 Malfunction - Open pedal sensor: lower than specified
values
• Check the circuit for open and short.
• Check the ECU pin #71, #53 for open
and poor contact.
- Check the accelerator pedal.
#1 Malfunction - Short pedal sensor: higher than specified
values
• Check the ECU pin #71, #53 for short
and poor contact.
P0120 Accelerator Pedal Sensor - The supply voltage is faulty. O
#1 Malfunction - Supply - Check the supply voltage to sensor.
Voltage Fault
and short.
AFFECTED VIN
DI10-58

#2 Malfunction - Open pedal sensor: lower than specified
values
and poor contact.
#2 Malfunction - Short pedal sensor: higher than specified
values
and poor contact.
P0220 Accelerator Pedal Sensor - The supply voltage is faulty. O
#2 Malfunction - Supply - Check the supply voltage to sensor.
Voltage Fault
and short.
P0192 Fuel Rail Pressure Sensor - The fuel rail pressure sensing values O
Malfunction - Open are lower than specified values.
• Minimum sensing values: - 1 1 2
bar (Open)
0.125 V
- Check the sensor and ECU wiring
harness.
and poor contact.
- Check the fuel rail pressure sensor.
AFFECTED VIN
DI10-59

P0193 Fuel Rail Pressure Sensor - The fuel rail pressure sensing values O
Malfunction - Short are higher than specified values.
• Maximum sensing values: 1,600 bar
(Short)
• Output voltage at 1600 bar: 4.055±
0.125V
pressure: 0.5±0.04V
harness.
and poor contact.
P0190 Supply Voltage Fault to - The supply voltage to fuel rail pres- O
Fuel Rail Pressure Sensor sure sensor is faulty.
• Output voltage at 1600 bar: 4.055±
0.125V
pressure: 0.5±0.04V
harness.
and short.
P0191 Fuel Rail Pressure Sensor - The rail pressure drop is too high. O
Signal Fault - Check the supply voltage to sensor.
0.125 V
harness.
and short.
AFFECTED VIN
DI10-60

P1192 Fuel Rail Pressure Sensor - The rail pressure sensor initial values O
Initial Signal Fault - Low are lower than specified values with
the ignition “ON”.
• Minimum sensing values: - 90 bar
(Open)
0.125 V
harness.
and poor contact.
Initial Signal Fault - High are higher than specified values with
the ignition “ON”.
• Maximum sensing values: 90 bar
(Short)
0.125 V
harness.
and poor contact.
Initial Signal Fault are higher or lower than specified val-
ues with the ignition “ON”.
• Maximum sensing values: 90 bar
(Short)
• Minimum sensing values: - 90 bar
(Open)
0.125 V
harness.
and short.
AFFECTED VIN
DI10-61

P0215 Main Relay Fault - Stuck - The main relay is stuck ; Shut down.
- Resistance of main relay: 92 Ω ± 9 Ω
(at 20°C)
- Check the main relay wiring harness.
• Check the ECU pin #3, 4, 5 for open
and short.
replace the ECU.
- Check the fuse for main relay
P1500 Vehicle Speed Fault - The vehicle speed signal through CAN
communication is faulty.
- Check the CAN communication line for
open and short.
- Check the ABS/ESP and TCU commu-
nication lines.
P0642 ECU Supply Voltage 1 Fault - Malfunction reference supply voltage
- Low (5 V) from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- High (5 V) from ECU
sor
sensor, cam sensor
(5 V) from ECU
sor
sensor, cam sensor
AFFECTED VIN
DI10-62

P0652 ECU Supply Voltage 2 Fault - Malfunction reference supply voltage O O
- Low (5 V) from ECU
sor
sensor, cam sensor
- High (5 V) from ECU
sor
sensor, cam sensor
(5 V) from ECU
sor
sensor, cam sensor
P0698 ECU Supply Voltage Fault - - Malfunction reference supply voltage
Low (2.5 V) from ECU
• Supply voltage: 2.5 V
sor
• Supply voltage (2.5 V): accelerator
pedal sensor 2
P0699 ECU Supply Voltage Fault - - Malfunction reference supply voltage
High (2.5 V) from ECU
sor
• Supply voltage (2.55 V): accelera-
tor pedal sensor 2
AFFECTED VIN
DI10-63

P0697 ECU Supply Voltage Fault - Malfunction reference supply voltage
(2.5 V) from ECU
sor
• Supply voltage (2.55 V): accelera-
tor pedal sensor 2
P0245 Turbo Charger Actuator - The waste gate driver circuit is short O
Circuit Fault - Short to ground or open
- Check the actuator wiring harness.
- Check the solenoid valve.
short.
P0246 Turbo Charger Actuator - The turbo charger actuator power O
Circuit Fault - Short to B+ source circuit is short.
- Check the actuator wiring harness.
- Check the solenoid valve.
- Check the ECU wiring harness for short
and poor contact.
P0606 ECU Watchdog Fault - The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
P1607 ECU Injector Cut Fault - The ECU is defective.
harness.
- Check the ECU.
P1600 ECU Shut Down Fault - The ECU is defective.
harness.
- Check the ECU.
P1601 ECU Fault - The ECU is defective.
harness.
- Check the ECU.
harness.
- Check the ECU.
AFFECTED VIN
DI10-64

P1614 ECU C2I/MDP Fault - The ECU is defective. O
harness.
- Check the ECU.
P1615 ECU Fault - The ECU is defective. O
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
harness.
- Check the ECU.
P1148 Accelerometer (Knock - Check if the MDP is successful. O
Sensor) Learning Fault - Check the accelerometer (knock
sensor) sensor and wiring harness.
AFFECTED VIN
DI10-65

P0400 EGR Control Valve Fault - When the EGR emission is more than
specified value.
• The EGR controller circuit is open
or short to ground.
• The EGR controller is short to
battery.
noid valve.
- Check if the EGR valve is stuck.
- Check the resistance of EGR valve: 15.
4 Ω.
short.
P1235 VGT Operation Fault - The boost pressure control is faulty. O
- Check the air intake system.
- Check the wiring harness and the ECU
wiring harness.
harness.
- Check the ECU.
P0335 No Crank Signals - Refer to P0372.
P1170 Torque Trim Fault - High - Refer to P0372.
P1676 Glow Plug Communication - The communication between ECU and
Fault glow plug is faulty.
- Check the communication line between
ECU and glow plug.
- Check the glow plug wiring harness.
- Check the resistance of glow plug:
below 1 Ω.
- Check the glow plug relay.
ground.
P1677 Glow Plug Controller Fault - The communication between ECU and
glow plug is faulty.
ECU and glow plug.
- Check the glow plug wiring harness.
- Check the resistance of glow plug:
below 1Ω.
- Check the glow plug relay.
ground.
AFFECTED VIN
DI10-66

P0671 #1 Glow Plug Fault - Open - The glow plug circuit is open.
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1 Ω.
- Check each glow plug relay.
plug: below 1 Ω.
plug: below 1 Ω.
plug: below 1Ω.
plug: below 1 Ω.
P1671 #1 Glow Plug Fault - Short - The glow plug circuit is short.
(B+) - Check the communication line between
plug: below 1 Ω.
AFFECTED VIN
DI10-67

plug: below 1 Ω
plug: below 1 Ω
plug: below 1 Ω
plug: below 1Ω
P0700 TCU Signal Fault - The communication between ECU and
TCU is faulty.
ECU and TCU.
- Check the ECU pin #54, 73 for open
and short.
P1540 Air Conditioner Operating - Check the air conditioner sensors and
Circuit Fault - Open wiring harnesses.
- Check the ECU if required.
Circuit Fault - Short wiring harnesses.
Circuit Fault - Short to wiring harnesses.
Ground - Check the ECU wiring harness.
AFFECTED VIN
DI10-68

P1149 Too High Water Level in - Drain the water from fuel filter.
Fuel Filter
P1634 Immobilizer Fault (refer to - No response from immobilizer.
immobilizer section) - Perform the immobilizer coding again.
short.
- Check the immobilizer unit for open and
short or check the supply voltage.
- Check the immobilizer antenna.
P1635 No response from Immobi- - No response from immobilizer.
lizer (refer to immobilizer - Perform the immobilizer coding again.
section)
short.
- Check the immobilizer antenna.
P1630 Wrong response from Im- - The invalid key is inserted or no communi-
mobilizer (refer to immobi- cation between transponder and immobi-
lizer section) lizer (no response from transponder).
- Perform the immobilizer coding again.
short.
- Check the immobilizer antenna and
transponder for damage.
P1631 Immobilizer Fault (refer to - The immobilizer is not operating.
short.
P1632 Immobilizer Fault (refer to - No response from immobilizer.
short.
AFFECTED VIN
DI10-69

P1633 Immobilizer Fault (refer to - No key coding.
short.
P0633 Immobilizer Fault (refer to - Key memory is not available (permissible
immobilizer section) - 5).
- Perform the immobilizer coding again.
short.
P1636 Immobilizer Fault (refer to - Severe trouble is not defined.
short.
AFFECTED VIN
MEMO
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................
DI10-71
INDEX OF DTC
HMF sensor Signal Fault (Electric Failure) .......... DI10-75 Brake Lamp Signal Fault ..................................... DI10-91
P0102 ............................................................ DI10-75 P1572 ............................................................ DI10-91
P0103 ............................................................ DI10-75 P1571 ............................................................ DI10-91
P0100 ............................................................ DI10-75
High Wiring Resistance (Injector #1) ................... DI10-92
Cam Position Sensor (missing event) .................. DI10-76 P1286 ............................................................ DI10-92
P0344 ............................................................ DI10-76 P1287 ............................................................ DI10-92
Cam Position Sensor Malfunction High Wiring Resistance (Injector #2) ................... DI10-93
(Poor Synchronization of Crank and Cam) ........... DI10-77 P1288 ............................................................ DI10-93
P0341 ............................................................ DI10-77 P1289 ............................................................ DI10-93
Too Small Clearance of Crank Angle Sensor ........ DI10-78 High Wiring Resistance (Injector #3) ................... DI10-94
P0219 ............................................................ DI10-78 P1292 ............................................................ DI10-94
P1293 ............................................................ DI10-94
Too Large Clearance of Crank Angle Sensor ........ DI10-79
P0336 ............................................................ DI10-79 High Wiring Resistance (Injector #4) ................... DI10-95
P1294 ............................................................ DI10-95
Crank Angle Sensor Malfunction .......................... DI10-80
P1295 ............................................................ DI10-95
P0372 ............................................................ DI10-80
High Wiring Resistance (Injector #5) ................... DI10-96
Barometric Sensor Malfunction (Out of range, using
P1290 ............................................................ DI10-96
strategy of restoring by MAP sensor) .................. DI10-81
P1291 ............................................................ DI10-96
P1107 ............................................................ DI10-81
P1108 ............................................................ DI10-81 Clutch Switch Malfunction ................................... DI10-97
P1105 ............................................................ DI10-81 P0704 ............................................................ DI10-97
Battery Voltage Monitoring Signal Malfunction ..... DI10-82 Coolant Temperature Sensor Malfunction
P0562 ............................................................ DI10-82 (Implausible Signal) ............................................. DI10-98
P0563 ............................................................ DI10-82 P1115 ............................................................. DI10-98
P0560 ............................................................ DI10-82
Coolant Temperature Sensor Malfunction
Booster Pressure Sensor Malfunction (Electric Fault) .................................................... DI10-99
(Out of range with Key ON) ................................. DI10-84 P0117 ............................................................ DI10-99
P0109 ............................................................ DI10-84 P0118 ............................................................ DI10-99
P0106 ............................................................ DI10-84 P0115 ............................................................ DI10-99
Booster Pressure Sensor Malfunction Too Fast or Low Main Relay Operation .............. DI10-100
(Out of range with Key ON) ................................. DI10-86 P0685 .......................................................... DI10-100
P0107 ............................................................ DI10-86
EGR Actuator Malfunction ................................. DI10-101
P0108 ............................................................ DI10-86
P1405 .......................................................... DI10-101
P0105 ............................................................ DI10-86
P1406 .......................................................... DI10-101
P1106 ............................................................ DI10-86
Condenser Fan Driving Signal Fault (Type 1) ..... DI10-102
Booster Pressure Malfunction
P1480 .......................................................... DI10-102
(Implausible Signal) ............................................. DI10-88
P1481 .......................................................... DI10-102
P1109 ............................................................ DI10-88
P1482 .......................................................... DI10-102
Brake Pedal Switch Malfunction .......................... DI10-90
P0571 ............................................................ DI10-90
AFFECTED VIN
DI10-72
Condenser Fan Driving Signal Fault (Type 2) ..... DI10-103 Open Circuit (Injector #3) ................................... DI10-119
P1526 .......................................................... DI10-103 P0203 .......................................................... DI10-119
P1527 .......................................................... DI10-103
HSD Circuit Short to LSE (Injector #1) .............. DI10-120
P1528 .......................................................... DI10-103
P1201 .......................................................... DI10-120
#1 Accelerometer Malfunction
(Idling Signal/Too Small Noise Ratio) ................. DI10-104
P1202 .......................................................... DI10-121
P0325 .......................................................... DI10-104
P1204 .......................................................... DI10-122
(Idling Signal/Too Small Noise Ratio) ................. DI10-105
P0330 .......................................................... DI10-105 HSD Circuit Short to LSE (Injector #5) .............. DI10-123
P1205 .......................................................... DI10-123
Injector Bank 1 Malfunction
(Short to Ground or B+) ..................................... DI10-106 HSD Circuit Short to LSE (Injector #3) .............. DI10-124
P1611 .......................................................... DI10-106 P1203 .......................................................... DI10-124
P1612 .......................................................... DI10-106 Fuel Temperature Sensor Malfunction ................ DI10-125
Injector Bank 2 Malfunction P0182 .......................................................... DI10-125
(Short to Ground or B+) ..................................... DI10-108 P0183 .......................................................... DI10-125
P1618 .......................................................... DI10-108 P0180 .......................................................... DI10-125
P1619 .......................................................... DI10-108 Glow Plug Malfunction (Driving Signal) .............. DI10-126
Cylinder Balancing Fault (Injector #1) = P1678 .......................................................... DI10-126
Clogged Air Intake System ................................ DI10-110 P1679 .......................................................... DI10-126
P0263 .......................................................... DI10-110 Heater 1 Malfunction (Driving Signal) ................. DI10-127
Cylinder Balancing Fault (Injector #2) = P1530 .......................................................... DI10-127
Clogged Air Intake System ................................. DI10-111 P1531 .......................................................... DI10-127
P0266 ........................................................... DI10-111 P1532 .......................................................... DI10-127
Cylinder Balancing Fault (Injector #4) = Heater 2 Malfunction (Driving Signal) ................. DI10-128
Clogged Air Intake System ................................ DI10-112 P1534 .......................................................... DI10-128
P0272 .......................................................... DI10-112 P1535 .......................................................... DI10-128
P1536 .......................................................... DI10-128
Cylinder Balancing Fault (Injector #5) =
Clogged Air Intake System ................................ DI10-113 Rail Pressure Control Fault
P0275 .......................................................... DI10-113 (Too High Pressure) ........................................... DI10-129
P1254 .......................................................... DI10-129
P1253 .......................................................... DI10-129
Clogged Air Intake System ................................ DI10-114
P0269 .......................................................... DI10-114 Rail Pressure Control Fault
(Too High IMV Current Trim, drift) ....................... DI10-131
Open Circuit (Injector #1) ................................... DI10-115
P1256 .......................................................... DI10-131
P0201 .......................................................... DI10-115
P1257 .......................................................... DI10-131
Open Circuit (Injector #2) ................................... DI10-116 P1258 .......................................................... DI10-131
P0202 .......................................................... DI10-116 P1259 .......................................................... DI10-131
Open Circuit (Injector #4) ................................... DI10-117 Rail Pressure Control Fault
P0204 .......................................................... DI10-117 (Too Slow Pressure Build Up while Cranking) .... DI10-133
P1191 .......................................................... DI10-133
Open Circuit (Injector #5) ................................... DI10-118
P0205 .......................................................... DI10-118
AFFECTED VIN
DI10-73
IMV Operation Fault (Electrical Fault) ................ DI10-135 Accelerator Pedal Sensor Malfunction
P0255 .......................................................... DI10-135 (Electrical Fault, Track 2) .................................. DI10-147
P0251 .......................................................... DI10-135 P0222 .......................................................... DI10-147
P0253 .......................................................... DI10-135 P0223 .......................................................... DI10-147
P0220 .......................................................... DI10-147
Intake Air Temperature Sensor Fault
(Electric Fault) .................................................. DI10-136 Fuel Rail Pressure Sensor Malfunction
P0112 .......................................................... DI10-136 (Out of Range, ADC or Vref) .............................. DI10-148
P0113 .......................................................... DI10-136 P0192 .......................................................... DI10-148
P0110 .......................................................... DI10-136 P0193 .......................................................... DI10-148
P0190 .......................................................... DI10-148
MDP Fault (Injector #1) ..................................... DI10-137
P0191 .......................................................... DI10-148
P1171 .......................................................... DI10-137
Fuel Rail Pressure Sensor Malfunction
MDP Fault (Injector #2) ..................................... DI10-137
(Out of Range when Key ON) ............................ DI10-150
P1172 .......................................................... DI10-137
P1192 .......................................................... DI10-150
MDP Fault (Injector #4) ..................................... DI10-138 P1193 .......................................................... DI10-150
P1174 .......................................................... DI10-138 P1190 .......................................................... DI10-150
MDP Fault (Injector #5) ..................................... DI10-138 Main Relay Malfunction - Stuck ......................... DI10-152
P1175 .......................................................... DI10-138 P0215 .......................................................... DI10-152
MDP Fault (Injector #3) ..................................... DI10-139 Vehicle Speed Fault .......................................... DI10-153
P1173 .......................................................... DI10-139 P1500 .......................................................... DI10-153
Rail Pressure Fault (Too High) ........................... DI10-140 5V Supply Voltage 1 Fault ................................. DI10-154
P1252 .......................................................... DI10-140 P0642 .......................................................... DI10-154
Accelerator Pedal Sensor Malfunction P0643 .......................................................... DI10-154
(Relationship between Track 1 and Track 2) ...... DI10-142 P0641 .......................................................... DI10-154
P1120 .......................................................... DI10-142 5V Supply Voltage 2 Fault ................................. DI10-155
P1121 .......................................................... DI10-142 P0652 .......................................................... DI10-155
(Limp Home Mode Operation) ........................... DI10-143 P0651 .......................................................... DI10-155
P1122 .......................................................... DI10-143 2.5V Supply Voltage Fault ................................. DI10-156
(Torque Reduction Mode Operation) .................. DI10-144 P0699 .......................................................... DI10-156
P1123 .......................................................... DI10-144 P0697 .......................................................... DI10-156
Accelerator Pedal Sensor Malfunction Turbo Charger Actuator Operation Fault (signal) DI10-157
(Electrical Fault, Pedal Stuck) ......................... DI10-145 P0245 .......................................................... DI10-157
P1124 .......................................................... DI10-145 P0246 .......................................................... DI10-157
Accelerator Pedal Sensor Malfunction ECU Watchdog Fault ........................................ DI10-158

(Electrical Fault, Track 1) .................................. DI10-146 P0606 .......................................................... DI10-158
P0122 .......................................................... DI10-146 ECU Watchdog Fault (Injector Cut-off) ............... DI10-159
P0123 .......................................................... DI10-146 P1607 .......................................................... DI10-159
P0120 .......................................................... DI10-146
ECU Watchdog Fault (Watchdog Trip) .............. DI10-160
P1600 .......................................................... DI10-160
P1601 .......................................................... DI10-160
P1602 .......................................................... DI10-160
AFFECTED VIN
DI10-74
ECU Non-Volatile Memory Fault ........................ DI10-161 Glow Plug Module Circuit Malfunction - Open .... DI10-171
P1614 .......................................................... DI10-161 P0674 .......................................................... DI10-171
P1615 .......................................................... DI10-161 P0675 .......................................................... DI10-171
P1616 .......................................................... DI10-161 P0671 .......................................................... DI10-171
P1606 .......................................................... DI10-161 P0672 .......................................................... DI10-171
P1620 .......................................................... DI10-161 P0673 .......................................................... DI10-171
P1621 .......................................................... DI10-161
Glow Plug Module Circuit Malfunction - Short .... DI10-172
P1622 .......................................................... DI10-161
P1674 .......................................................... DI10-172
ECU Memory Integration Fault .......................... DI10-162 P1675 .......................................................... DI10-172
P1603 .......................................................... DI10-162 P1671 .......................................................... DI10-172
P1604 .......................................................... DI10-162 P1672 .......................................................... DI10-172
P1605 .......................................................... DI10-162 P1673 .......................................................... DI10-172
Accelerometer Learning Fault ............................ DI10-163 TCU Signal Fault ............................................... DI10-173
P1148 .......................................................... DI10-163 P0700 .......................................................... DI10-173
EGR Valve Control Fault .................................... DI10-164 Air Conditioner Operating Circuit Fault .............. DI10-174
P0400 .......................................................... DI10-164 P1540 .......................................................... DI10-174
P1541 .......................................................... DI10-174
VGT Operation Fault ......................................... DI10-165
P1542 .......................................................... DI10-174
P1235 .......................................................... DI10-165
Excessive Water in Fuel Filter ........................... DI10-175
TBD .................................................................. DI10-167
P1149 .......................................................... DI10-175
P1608 .......................................................... DI10-167
Immobilizer Malfunction ..................................... DI10-176
No Crank Signal ................................................ DI10-168
P1634 .......................................................... DI10-176
P0335 .......................................................... DI10-168
P4335 .......................................................... DI10-176
High Torque Trim ............................................... DI10-169 P1630 .......................................................... DI10-176
P1170 .......................................................... DI10-169
P1631 .......................................................... DI10-176
Glow Plug Module Communication Fault ........... DI10-170 P1632 .......................................................... DI10-176
P1676 .......................................................... DI10-170 P1633 .......................................................... DI10-176
P1677 .......................................................... DI10-170 P0633 .......................................................... DI10-176
P1636 .......................................................... DI10-176
AFFECTED VIN
DI10-75
TROUBLE DIAGNOSIS PROCEDURES
HMF sensor Signal Fault (Electric Failure)
Trouble Code and Symptom
Trouble Code Symptom
P0102 Low Signal MIL ON
P0103 High Signal Not available EGR control(Air flow)
P0100 Supply Voltage
Diagnosis Procedures
Read DTC
YES
Fault in sensor supply voltage? Sensor problem caused by supply voltage.
Locate the problem while disconnecting the
sensor connector one by one. If not a sen-
sor problem, check the sensor supply volt-
age circuit for open and short.
NO
Check sensor wiring

NO
YES
Wiring Problem? Repair or
replace Check wiring and insulation
NO
YES
Wiring Problem? Repair wiring
Check sensor resistance
NO
YES
Resistance Problem? Replace
sensor Replace ECU
Check ECU wiring
YES
replace
NO
AFFECTED VIN
DI10-76
Cam Position Sensor (missing event)
P0344 Cam Position Sensor Malfunction
Check sensor wiring
YES NO
replace
Check wiring insulation
NO
YES
Check sensor Wiring Problem? Repair wiring
YES NO
Sensor Problem? Replace
sensor
Check cam installation
NO
YES
Check ECU wiring Cam Wheel Problem? Replace cam
wheel
YES NO
replace
Replace ECU
NO
Check if the cam and

flywheel signals are normal
with an oscilloscope
YES
Anmormal Signal? Repair or
replace
AFFECTED VIN
DI10-77
Cam Position Sensor Malfunction

(Poor Synchronization of Crank and Cam)
P0341 Cam Position Sensor Malfunction - Poor Synchro- MIL ON

nization
Check sensor wiring
YES NO
replace
NO
YES
Check sensor Wiring Problem? Repair wiring
YES NO
sensor
Check cam installation
NO
YES
Check ECU wiring Cam Wheel Problem? Replace cam
wheel
YES NO
replace
Replace ECU
NO
Check if the cam and

flywheel signals are normal
with an oscilloscope
YES
Anmormal Signal? Repair wiring
AFFECTED VIN
DI10-78
Too Small Clearance of Crank Angle

Sensor
P0219 Too Small Clearance of Crank Angle Sensor
Check sensor wiring
YES
replace
YES
Trouble Continues? Replace APS
NO wheel
NO
Check ECU wiring
Replace wheel
YES
replace
YES
Trouble Continues? Replace ECU
NO
NO
Check insulation and open
circuit
Repair completed
YES
NO
YES
Trouble Continues? Replace VR
sensor
NO
New sensor installed
AFFECTED VIN
DI10-79
Too Large Clearance of Crank Angle

Sensor
P0336 Too Large Clearance of Crank Angle Sensor MIL ON
Check sensor wiring
YES
replace
YES
NO wheel
NO
Check ECU wiring
Replace wheel
YES
replace
YES
NO
NO
circuit
Repair completed
YES
NO
YES
sensor
NO
AFFECTED VIN
DI10-80
Crank Angle Sensor Malfunction
P0372 Crank Angle Sensor Malfunction 3 MIL ON
Check sensor wiring
YES
replace
YES
NO wheel
NO
Check ECU wiring
Replace wheel
YES
replace
YES
NO
NO
circuit
Repair completed
YES
NO
YES
sensor
NO
AFFECTED VIN
DI10-81
Barometric Sensor Malfunction

(Out of range, using strategy of
restoring by MAP sensor)
P1107 Low Signal
P1108 High Signal
Replace ECU
AFFECTED VIN
DI10-82
Battery Voltage Monitoring Signal

Malfunction
P0562 Low Signal Not operatable.
P0563 High Signal Injector #1 resistance fault. Use estimate resis-

tance level.
P0560 Supply Voltage Injector #2 resistance fault. Use estimate resis-

tance level.
Injector #4 resistance fault. Use estimate resis-

tance level.

tance level.

tance level.
Unable EGR control (Air Flow)
Unable RPC trim problem detection
Unable HP leak detection
Unable accelerometer learing strategy
MIL ON
Operating limited rail pressure mode
TBD
AFFECTED VIN
DI10-83
Key ON and check battery

voltage
YES
Battery Problem? Charge
battery
Charge battery, check wiring
NO
YES
Charge battery, wiring problem Repair or
Check battery wiring replace
NO
YES
Battery Wiring Problem? Repair or
replace
Replace ECU
NO
Check ECU wiring
YES
replace
NO
Check resistance of body

ground and ECU ground
YES
High Resistance Repair ECU
ground
AFFECTED VIN
DI10-84
Booster Pressure Sensor Malfunction

(Out of range with Key ON)
P0109 Low
P0106 High Location demand=change the boost control to

O.L. mode at f (boost demand, engine cycling speed)
1. Diagnosis Procedures (Boost Pressure)
Read DTC
YES
Booster Pressure Problem? Refer to Diagnosis Tree “Check sensor(1)”
NO
Check air line malfunction:

* VGT/Turbo. * Air filter.
* Vacuum line. * Vacuum pump.
* Solenoid valve open.
* Vane condition.
* Air inlet valve function
Repiar Completed
AFFECTED VIN
DI10-85
2. Diagnosis Procedure (Check sensor (1))
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
Visually check sensor
NO
YES
sensor Replace sensor
NO
YES
Check ECU wiring
NO
YES
replace Repiar Completed
NO
AFFECTED VIN
DI10-86
Booster Pressure Sensor Malfunction

(Out of range with Key ON)
P0107 Low
P0108 High Location demand=change the boost control to

P1106 GRAD
Read DTC
YES
Booster Pressure Problem? Refer to Diagnosis Tree “Check sensor(1)”
NO

* Vane condition.
Repiar Completed
AFFECTED VIN
DI10-87
2. Diagnosis Procedures (check sensor (1))
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-88
Booster Pressure Malfunction

(Implausible Signal)
P1109 Booster Pressure Sensor Malfunction
Location demand=change the boost control to

Read DTC
YES
Booster Pressure Sensor Refer to Diagnosis Tree “Check sensor(1)”
Problem?
NO

* Vane condition.
Repiar Completed
AFFECTED VIN
DI10-89
2. Diagnosis Procedures (check sensor (1))
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-90
Brake Pedal Switch Malfunction
P0571 Brake Pedal Switch Malfunction MIL ON
Unable Cruise Control
Check switch wiring
YES NO
replace
Check ECU wiring
NO
YES
Check 12V switch supply Wiring Problem? Repair or
voltage replace
NO
YES
Source Power Problem? Check wiring
and fuse
Check wiring and insulation
NO
YES
Check switch operation
NO
YES
Switch Problem? Replace
switch
Replace ECU
AFFECTED VIN
DI10-91
Brake Lamp Signal Fault
P1572 Brake Lamp Signal Fault MIL ON
P1571 Brake Lamp Signal Fault MIL ON
Check switch wiring
YES NO
replace
Check ECU wiring
NO
YES
voltage replace
NO
YES
and fuse
NO
YES
NO
YES
Switch Problem? Replace
switch
Replace ECU
AFFECTED VIN
DI10-92
High Wiring Resistance (Injector #1)
P1286 Low Resistance of injector #1 fault. Use estimate re-

sistance level.
P1287 High MIL ON
Unable Dynamic Leak of Injector #1
Unable Accelerometer Learning Strategy
Read DTC
YES
“Low” Fault? Refer to
injector circuit
malfunction
NO (open) tree
Read DTC
YES
“High” Fault? Refer to
injector circuit
malfunction
NO (short) tree
No any other possibility
AFFECTED VIN
DI10-93

sistance level.
P1289 High MIL ON
Read DTC
YES
injector circuit
malfunction
NO (open) tree
Read DTC
YES
“High”s Fault? Refer to
injector circuit
malfunction
NO (short) tree
AFFECTED VIN
DI10-94

sistance level.
P1293 High MIL ON
Read DTC
YES
injector circuit
malfunction
NO (open) tree
Read DTC
YES
injector circuit
malfunction
NO (short) tree
AFFECTED VIN
DI10-95

sistance level.
P1295 High MIL ON
Read DTC
YES
injector circuit
malfunction
NO (open) tree
Read DTC
YES
injector circuit
malfunction
NO (short) tree
AFFECTED VIN
DI10-96

sistance level.
P1291 High MIL ON
Read DTC
YES
injector circuit
malfunction
NO (open) tree
Read DTC
YES
injector circuit
malfunction
NO (short) tree
AFFECTED VIN
DI10-97
Clutch Switch Malfunction
P0704 Clutch Switch Malfunction
Check switch wiring
YES NO
replace
Check ECU wiring
NO
YES
voltage replace
NO
YES
and fuse
NO
YES
NO
YES
Switch Contact Problem? Replace switch
Replace ECU
AFFECTED VIN
DI10-98

(Implausible Signal)
P1115 Coolant Temperature Sensor Malfunction Unable Air Conditioner Operation
Below Limited Temperature of Engine Overheat

Detection
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
sensor Replace ECU
NO
Check ECU wiring
YES
replace
NO
AFFECTED VIN
DI10-99

(Electric Fault)
P0117 Low Unable Air Conditioner Operation
P0118 High Below Limited Temperature of Engine Overheat

Detection
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
sensor Replace ECU
NO
Check ECU wiring
YES
replace
AFFECTED VIN
DI10-100
Too Fast or Low Main Relay Operation
P0685 Main Relay Malfunction
Check relay wiring
YES NO
replace
Perform forced operation
NO and replace relay
Check ECU wiring YES

Not available forced operation? Replace ECU
YES
Wiring Problem? Repair or NO
replace
NO
Repiar Completed
YES
AFFECTED VIN
DI10-101
EGR Actuator Malfunction
P1405 EGR Vacuum Modulator - Short to GND MIL ON
P1406 EGR Vacuum Modulator - Short to +Batt Unable EGR Control (Air Flow)
Check actuator wiring
NO
YES
replace Replace actuator
NO
YES
Check resistance of actuator
NO
YES
actuator
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO
AFFECTED VIN
DI10-102
Condenser Fan Driving Signal Fault

(Type 1)
P1480 Open Circuit Unable Air Conditioner Operation
P1481 Short Circuit MIL ON
P1482 Short to Ground Below Limited Temperature of Engine Overheat

Detection
Check relay wiring
NO
YES
replace
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO

and replace relay
YES
NO
AFFECTED VIN
DI10-103
Condenser Fan Driving Signal Fault

(Type 2)
P1526 Open Circuit Unable Air Conditioner Operation
P1527 Short Circuit MIL ON
P1528 Short to Ground Below Limited Temperature of Engine Overheat

Detection
Check relay wiring
NO
YES
replace
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO
Perform forced drive and

replace relay
YES
NO
AFFECTED VIN
DI10-104
(Idling Signal/Too Small Noise Ratio)
P0325 #1 Accelerometer (Knock Sensor) Malfunction MIL ON
“Caution: Check the sensing

value of coolant temp., intake
air temp., fuel temp. baromet-
ric pressure. Incorrect default
values of theses sensors may
cause wrong diagnosis.”
Check accelerometer wiring

and tightening torque, espe-
cially shield ground.
NO
YES
replace Replace accelerometer
(knock sensor)
NO
YES
Check ECU wiring Trouble Continues? Replace ECU
NO
YES
replace
Repiar Completed
NO
YES
NO
AFFECTED VIN
DI10-105
(Idling Signal/Too Small Noise Ratio)
P0330 #2 Accelerometer (Knock Sensor) Malfunction MIL ON
“Caution: Check the sensing

value of coolant temp., intake
air temp., fuel temp. baromet-
ric pressure. Incorrect default
values of theses sensors
may cause wrong diagnosis.”
Check accelerometer wiring

and tightening torque,
especially shield ground.
NO
YES
replace Replace accelerometer
(knock sensor)
NO
YES
Check ECU wiring Trouble Continues? Replace ECU
NO
YES
replace
Repiar Completed
NO
YES
NO
AFFECTED VIN
DI10-106

(Short to Ground or B+)
P1611 Low Injector Bank 1 Voltage Resistance of injector #1 fault. Use estimate re-
sistance level.
P1612 High Injector Bank 1 Voltage Resistance of injector #4 fault. Use estimate re-
sistance level.
Resistance of injector #3 fault. Use estimate re-

sistance level.
MIL ON
Unable Cylinder Balancing
Unable Injector #1 Operation
Unable High Pressure Leak Detection
AFFECTED VIN
DI10-107
1. Fuel Injection Bank 1/2 2. Check Injector Wiring
Injector - short (SC+ or SC-) Check ECU wiring
Key OFF and check injector

wiring
YES
replace
YES
Injector Wiring Problem? Repair or NO
replace
NO
Disconnect injector connec- YES

tor and key ON Wiring Problem? Repair wiring
YES NO
Trouble Continues? Refer to check
injector wiring
NO Replace ECU
Delete default and key OFF.

Key ON while connecting
injector connectors one by one.
YES
Trouble Recurred? Replace the
injector - Enter
new injector
NO C2I into ECU
Repeat same procedures for

all injectors
AFFECTED VIN
DI10-108

(Short to Ground or B+)
P1618 Low Injector Bank 2 Voltage Resistance of injector #2 fault. Use estimate re-
sistance level.
P1619 High Injector Bank 2 Voltage Resistance of injector #5 fault. Use estimate re-
sistance level.
MIL ON
Unable High Pressure Leak Detection
AFFECTED VIN
DI10-109
1. Fuel Injection Bank 1/2 2. Check Injector Wiring
Injector - short Check ECU wiring

wiring
YES
replace
YES
Injector Wiring Problem? Repair or NO
replace
NO
Disconnect injector connec- YES

tor and key ON Wiring Problem? Repair wiring
YES NO
Trouble Continues? Refer to check
injector wiring
NO Replace ECU
Delete default and key OFF.

Key ON while connecting
injector connectors one by one.
YES
Trouble Recurred? Replace the
injector - Enter
new injector
NO C2I into ECU
Repeat same procedures for

all injectors
AFFECTED VIN
DI10-110

Clogged Air Intake System
P0263 #1 Cylinder Balancing Fault MIL ON
Read DTC
NO
YES
Injector Circuit Open? Circuit Open:
Wiring problem Check air intake system
NO
YES
Air Intake System Clogged? Repair air
intake system
Check engine hardware
and check
NO EGR
YES
Engine Hardware Problem? Repair or
replace
Replace injector and enter new
injector C2I value into ECU
NO
Check glow plug
YES
Glow Plug Problem? Repair or
replace
NO
Perform forced valve opera-

tion and check it
YES
Valve Problem? Repair or
replace valve
NO
AFFECTED VIN
DI10-111

Read DTC
NO
YES
NO
YES
intake system
and check
NO EGR
YES
replace
Replace injector and enter
new injector C2I into ECU
NO
Check glow plug
YES
replace
NO

tion and check it
YES
replace valve
NO
AFFECTED VIN
DI10-112

Read DTC
NO
YES
NO
YES
intake system
and check
NO EGR
YES
replace
NO
Check glow plug
YES
replace
NO

tion and check it
YES
replace valve
NO
AFFECTED VIN
DI10-113

Read DTC
NO
YES
NO
YES
intake system
and check
NO EGR
YES
replace
NO
Check glow plug
YES
replace
NO

tion and check it
YES
replace valve
NO
AFFECTED VIN
DI10-114

Read DTC
NO
YES
NO
YES
intake system
and check
NO EGR
YES
replace
NO
Check glow plug
YES
replace
NO

tion and check it
YES
replace valve
NO
AFFECTED VIN
DI10-115
Open Circuit (Injector #1)
P0201 #1 Injector Circuit - Open Unable RPC Trim Fault Detection
Unable H/P Leak Detection

wiring
NO
YES
Wiring Problem? Repair or Check ECU wiring
replace
NO YES
replace
NO
YES
Wiring Problem? Repair or Replace ECU
replace
NO
“If the wiring is normal,

disconnect the injector
connectors and check the
resistance (difficult to check
injector resistance)”
YES
Injector Wiring Problem? Replace
injector
and enter new
NO injector C2I
value into ECU
AFFECTED VIN
DI10-116

wiring
NO
YES
replace
NO YES
replace
NO
YES
replace
NO

YES
injector
and enter new
NO injector C2I
value into ECU
AFFECTED VIN
DI10-117

wiring
NO
YES
replace
NO YES
replace
NO
YES
replace
NO

YES
injector
and enter new
NO injector C2I
value into ECU
AFFECTED VIN
DI10-118

wiring
NO
YES
replace
NO YES
replace
NO
YES
replace
NO

YES
injector
and enter new
NO injector C2I
value into ECU
AFFECTED VIN
DI10-119

wiring
NO
YES
replace
NO YES
replace
NO
YES
replace
NO

YES
injector
and enter new
NO injector C2I
value into ECU
AFFECTED VIN
DI10-120
HSD Circuit Short to LSE (Injector #1)
P1201 #1 Injector Circuit - Short Unable RPC Trim Fault Detection

wiring
NO
YES
Wiring Problem? Repair or Check wiring insulation
replace
NO YES
Disconnect injector connector

NO
YES
Same Trouble Continues? Replace Replace ECU
injector
and enter new
NO injector C2I
value into ECU
Shorted injector circuit.

Check wiring from injector tip
to ECU.
YES
replace
NO
AFFECTED VIN
DI10-121

wiring
NO
YES
replace
NO YES

NO
YES
injector
and enter new
NO injector C2I
value into ECU

to ECU.
YES
replace
NO
AFFECTED VIN
DI10-122

wiring
NO
YES
replace
NO YES

NO
YES
injector
and enter new
NO injector C2I
value into ECU

to ECU.
YES
replace
NO
AFFECTED VIN
DI10-123

wiring
NO
YES
replace
NO YES

NO
YES
injector
and enter new
NO injector C2I
value into ECU

to ECU.
YES
replace
NO
AFFECTED VIN
DI10-124

wiring
NO
YES
replace
NO YES

NO
YES
injector
and enter new
NO injector C2I
value into ECU

to ECU.
YES
replace
NO
AFFECTED VIN
DI10-125
Fuel Temperature Sensor Malfunction
P0182 Low
P0183 High
Read DTC
YES
Fault in sensor supply voltage? Sensor problem caused by supply voltage
to sensor. Locate the problem while dis-
connecting the sensor connectors one by
one. If not sensor problem, check sensor
supply voltage circuit for open and short.
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
sensor Replace ECU
NO
Check ECU wiring
YES
replace
NO
AFFECTED VIN
DI10-126
Glow Plug Malfunction (Driving Signal)
P1678 Open Circuit MIL ON
P1679 Short Circuit Glow Plug Indicator ON
P1680 Short to Ground
Check glow plug box wiring
NO
YES
replace
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO
Replace glow plug box
YES
NO
AFFECTED VIN
DI10-127
Heater 1 Malfunction (Driving Signal)
P1530 Open Circuit Unable Heater Operation
P1531 Short to +Batt
Check relay wiring
NO
YES
replace
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO

and replace relay
YES
NO
AFFECTED VIN
DI10-128
Heater 2 Malfunction (Driving Signal)
P1534 Open Circuit Unable Heater Operation
P1535 Short to +Batt
Check relay wiring
NO
YES
replace
Repiar Completed
NO
Check ECU wiring
YES
replace
NO
YES
NO

and replace relay
YES
NO
AFFECTED VIN
DI10-129
Rail Pressure Control Fault

(Too High Pressure)
P1254 Maximum Value Unable Accelerometer Decoding
P1253 Minimum Value MIL ON
1. Rail Pressure Control
Read DTC
YES
YES Transfer Fuel System Repair or
Rail preaaure sensor or IMV Refer to IMV
Problem? replace
Related DTC? diagnosis
NO
NO
YES Check high pressure fuel

Rail Pressure Sensor Repair or
system
Problem? replace
NO YES
H/P Fuel System Problem? Repair or
replace
Check transfer fuel system
NO
Replace ECU
AFFECTED VIN
DI10-130
2. Transfer Fuel System 3. High Pressyre Fuel System
Check fuel level Check high pressure fuel

system
YES
Fuel Exhausted? Add fuel YES
Cause Found? Add fuel
NO
NO
“Visually check transfer fuel

system (fuel leaks, installation)”
HP fuel system is normal
YES
Transfer Fuel System Repair or
Problem? replace
NO
Check if the air in transfer

fuel system is too much
YES
Excessive Air in Transfer Install a
Fuel System? container to
H/P pump
venturi.
Remove
venturi return
NO lines. Fill fuel
with hand
pump.
Check fuel filter specification
YES
Different Specification? Replace filter
with new one
NO
Transfer fuel system is normal
AFFECTED VIN
DI10-131
Rail Pressure Control Fault

(Too High IMV Current Trim, drift)
P1256 Small Delivery of Transfer Fuel Unable Accelerometer Decoding
P1257 Large Delivery of Transfer Fuel MIL ON
P1258 Small Delivery of High Pressure Fuel Unable Dynamic Leak of Injector #1
P1259 Large Delivery of High Pressure Fuel Unable Dynamic Leak of Injector #2
1. Diagnosis Procedures (Rail Pressure Control)
Read DTC
YES
Problem? replace
NO
NO

system
Problem? replace
NO YES
replace
NO
Replace ECU
AFFECTED VIN
DI10-132
2. Diagnosis Procedures (Transfer Fuel System)
Check fuel level
NO
YES
Fuel Exhausted? Add fuel
NO
YES
with new one
NO
YES
Transfer Fuel System Repair or Repiar Completed
Problem? replace
NO

fuel system is too much
YES
H/P pump
venturi.
Remove
venturi return
NO
lines. Fill fuel
with hand
pump.
3. Diagnosis Procedures (High Pressure Fuel System)
YES
Cause Found? Repair or
replace
NO
H/P Fuel System - Normal
AFFECTED VIN
DI10-133
Rail Pressure Control Fault (Too Slow

Pressure Build Up while Cranking)
P1191 Rail Pressure Build Up - Too Slow Unable Accelerometer Decoding
Limited Rail Pressure Mode Operation
Read DTC
YES
Problem? replace
NO
NO

system
Problem? replace
NO YES
replace
NO
Replace ECU
AFFECTED VIN
DI10-134
Check fuel level
NO
YES
NO
YES
with new one
NO
YES
Transfer Fuel System Repair or Transfer fuel system is normal
Problem? replace
NO

fuel system is too much (with
a low pressure tester)
YES
H/P pump
venturi.
Remove
venturi return
NO
lines. Fill fuel
with hand
pump.
3. Diagnosis Procedures (High Pressyre Fuel System)
YES
replace
NO
AFFECTED VIN
DI10-135
IMV Operation Fault (Electrical Fault)
P0255 Open Circuit Unable Accelerometer Decoding
P0251 Short Circuit Delayed Engine Stop
P0253 Short to Ground Unable Dynamic Leak of Injector #1
Check IMV wiring

NO
YES Check resistance of IMV

replace
NO YES
Resistance Problem? Replace H/P
pump and IMV
Check ECU wiring
NO
YES Replace ECU

replace
NO
YES
AFFECTED VIN
DI10-136
Intake Air Temperature Sensor Fault

(Electric Fault)
P0112 High MIL ON
P0113 Low
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
sensor Replace ECU
NO
Check ECU wiring
YES
replace
NO
AFFECTED VIN
DI10-137
MDP Fault (Injector #1)
P1171 #1 Injector MDP Fault Unable Accelerometer Decoding
MIL ON
Unable Pilot and Post Injection
Torque Limit For Injector Drift
Enter the injector data into

ECU after replacing injector
MIL ON

AFFECTED VIN
DI10-138
MIL ON

MIL ON

AFFECTED VIN
DI10-139
MIL ON

AFFECTED VIN
DI10-140
Rail Pressure Fault (Too High)
P1252 Too High IMV Pressure
Read DTC
NO
Check high pressure fuel

YES system
Rail preaaure sensor or IMV Refer to
Related DTC? IMV diagnosis
YES
NO H/P Fuel System Problem? Repair or
replace
YES NO
Problem? replace
Replace ECU
NO
YES
Transfer Fuel System Repair or
Problem? replace
AFFECTED VIN
DI10-141
Check fuel level
NO
YES
NO
YES
with new one
NO
YES
Transfer Fuel System Repair or Repiar Completed
Problem? replace
NO

fuel system is too much (with
a low pressure tester)
YES
H/P pump
venturi.
Remove
venturi return
lines. Fill fuel
with hand
pump.
3. Diagnosis Procedures (High Pressyre Fuel System)
YES
replace
NO
AFFECTED VIN
DI10-142
Accelerator Pedal Sensor Malfunction

(Relationship between Track 1 and Track 2)
P1120 Accelerator Pedal Sensor 1 Malfunction Unable Cruise Control
P1121 Accelerator Pedal Sensor 2 Malfunction
Torque Reduction Mode Operation
Read DTC
YES
NO
YES
Sensor Wiring Problem? Replace
sensor NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-143

(Limp Home Mode Operation)
P1122 Accelerator Pedal Sensor Malfunction (Limp MIL ON

Home Mode)
Limp Home Mode Operation
Read DTC
YES
NO
YES
Check sensor wiring Replace
sensor NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-144

(Torque Reduction Mode Operation)
P1123 Accelerator Pedal Sensor Malfunction (Torque MIL ON

Mode)
Read DTC
YES
NO
YES
Check sensor wiring Replace
sensor NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-145

(Electrical Fault, Pedal Stuck)
P1124 Accelerator Pedal Sensor Malfunction - Stuck Unable Cruise Control
Limp Home Mode Operation
Read DTC
NO
YES
Brake switch malfunction Repair or Check ECU wiring
replace brake
switch.
NO
YES
replace
Check if accelerator pedal is
normal NO
YES Check wiring insulation

Accelerator Pedal Stuck? Replace
accelerator
pedal YES
NO Wiring Problem? Repair wiring
Check if accelerator pedal NO

signal is correct with scan tool
Replace brake switch

YES
Signal Problem? Repair or
replace YES
NO
Check brake wiring connection NO
YES Repiar Completed

replace
AFFECTED VIN
DI10-146

(Electrical Fault, Track 1)
P0122 Low MIL ON
P0123 High Unable Cruise Control
P0120 Supply Voltage Limp Home Mode Operation
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-147

(Electrical Fault, Track 2)
P0222 Low MIL ON
P0223 High Unable Cruise Control
P0220 Supply Voltage Torque Reduction Mode Operation
Read DTC
YES
NO
Check sensor wiring

NO
YES
NO
YES
NO
YES
NO
YES
Check ECU wiring
NO
YES
NO
AFFECTED VIN
DI10-148

(Out of Range, ADC or Vref)
P0192 Low Unable Pilot and Post Injection
P0193 High Unable Dynamic Leak of Injector #1
P0190 Supply Voltage Unable Dynamic Leak of Injector #2
P0191 Excessive Pressure Drop Unable Dynamic Leak of Injector #4
Unable RPC Trim Fault Detection
Fully Forced Open IMV
Unable High Rail Pressure Detection
AFFECTED VIN
DI10-149
Read DTC
YES
Sensor Voltage Fault? Sensor problem caused by supply voltage
NO
Check sensor wiring

(Check sensor output) NO
YES
Wiring Problem? Repair or Replace rail and sensor
replace
NO YES
Check ECU wiring

NO
YES
Wiring Problem? Repair or Check fuel system
replace
NO
YES
AFFECTED VIN
DI10-150

(Out of Range when Key ON)
P1192 Low Unable Pilot and Post Injection
P1193 High Unable Dynamic Leak of Injector #1
P1190 Supply Voltage Unable Dynamic Leak of Injector #2
Unable RPC Trim Fault Detection
Fully Forced Open IMV
Unable High Rail Pressure Detection
AFFECTED VIN
DI10-151
Check sensor wiring

NO
YES
Wiring Problem? Repair or Reinstall connect and wiring
replace
NO
YES
Trouble Continues? Replace rail
and sensor
Check ECU wiring
NO
YES
Wiring Problem? Repair or Repair completed
replace
NO
Check resistance of wiring
YES
AFFECTED VIN
DI10-152
Main Relay Malfunction - Stuck
P0215 Main Relay Malfunction- Stuck MIL ON
Check relay wiring
NO
YES
replace Perform forced operation
and replace relay
NO
YES
Check ECU wiring Not available forced Replace ECU
operation?
YES
Wiring Problem? Repair or NO
replace
NO Repair completed
YES
AFFECTED VIN
DI10-153
Vehicle Speed Fault
P1500 Vehicle Speed Fault Unable Cruise Control
Check vehicle conditions
NO
YES
Automatic Transmission Recognize
Equipped? vehicle speed Check gear box target
through CAN.
Check CAN
NO and
YES
transmission. Gear Box Target Problem? Replace gear
box target
Check sensor and wiring NO
YES Install new target

replace
NO YES
Check ECU wiring

NO
YES
replace
NO
YES
replace
AFFECTED VIN
DI10-154
5V Supply Voltage 1 Fault
P0642 Low Unable Cruise Control
P0643 High
Supply Voltage 1 (5V):

Accelerator Pedal Sensor 1
“Supply Voltage 2 (5V): HFM
sensor, Rail pressure
sensor, Boost pressure
sensor and Cam sensor”
Supply Voltage (2.5 V): Accelera-
tor Pedal Sensor 2
Read DTC
YES
All DTCs for sensors Sensor problem caused by supply voltage to
connected to sensor supply sensor. Locate the problem while discon-
voltage? necting the sensor one by one. If not sensor
problem, check wiring.
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-155
5V Supply Voltage 2 Fault
P0652 Low
P0653 High
Supply Voltage 1 (5 V):

“Supply Voltage 2 (5 V): HFM
Supply Voltage (2.5 V): Accelera-
tor Pedal Sensor 2
Read DTC
YES
All DTCs for sensors Sensor problem caused by supply voltage
connected to sensor supply to sensor. Locate the problem while dis-
voltage? connecting the sensor one by one. If not
sensor problem, check wiring.
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-156
2.5V Supply Voltage Fault
P0698 Low Unable Cruise Control
P0699 High
Supply Voltage 1 (5 V):

“Supply Voltage 2 (5 V): HFM
Supply Voltage (2.5 V):
Read DTC
YES
All DTCs for sensors Sensor problem caused by supply voltage
connected to sensor supply to sensor. Locate the problem while dis-
voltage? connecting the sensor one by one. If not
sensor problem, check wiring.
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-157
Turbo Charger Actuator Operation Fault

(signal)
P0245 Short to GND Unable Cruise Control
P0246 Short Circuit to B+ Unable VGT Operation
Check actuator wiring
NO
YES
replace Replace actuator
NO
YES
Check resistance of actuator
NO
YES
Resistance Problem? Replace Repair completed
actuator
NO
Check EUC wiring
YES
replace
NO
YES
NO
AFFECTED VIN
DI10-158
ECU Watchdog Fault
P0606 ECU Watchdog Fault
Read DTC
YES
ECU Related DTC? Check body
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-159
ECU Watchdog Fault (Injector Cut-off)
P1607 ECU Injector Cut-off
Read DTC
YES
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-160
ECU Watchdog Fault (Watchdog Trip)
P1600 Trip TPU Write Fault
P1601 Trip Shut Dowm Write Fault
P1602 Trip Noise Write Fault
Read DTC
YES
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-161
ECU Non-Volatile Memory Fault
P1614 MDP MIL ON/Limp Home Mode Operation
P1615 Tele-Coding MIL ON/Limp Home Mode Operation
P1616 Watchdog MIL ON/Limp Home Mode Operation
P1606 CAN MIL ON/Limp Home Mode Operation
P1620 ECU Malfunction MIL ON/Limp Home Mode Operation
P1621 ECU Malfunction MIL ON/Limp Home Mode Operation
P1622 ECU Malfunction MIL ON
Read DTC
YES
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-162
ECU Memory Integration Fault
P1603 Code Integrity Immediately Engine Stop
Read DTC
YES
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-163
Accelerometer Learning Fault
P1148 Accelerometer (Knock Sensor) Learning Fault Torque Reduction Operation
Unable Cruise Control
Read DTC
YES
Knock Sensor Related DTC? Refer to
“Accelerom-
eter (Knock
NO Sensor)
Diagnosis”
Vehicl driving conditions are

not satisfy with MDP learning
requirements
AFFECTED VIN
DI10-164
EGR Valve Control Fault
P0400 EGR Valve Control Fault Unable Cruise Control
Read DTC
YES
EGR valve and HFM sensor Check
related DTC? sensors and
EGR system
NO
Check vacuum modulator/

turbo charger boost modula-
tor and vacuum lines for leak
and installation
Repair completed
AFFECTED VIN
DI10-165
VGT Operation Fault
P1235 VGT Operation Fault Unable Cruise Control
Location demand=change the boost control to O.L.

mode at f (boost demand, engine cycling speed)
1. Diagnosis Procedures(Boost Pressure)
Read DTC
YES
Boost Pressure Problem? Refer to
Diagnosis
Tree “Check
NO sensor(1)”

* Vane condition.
Repair completed
AFFECTED VIN
DI10-166
2. Diagnosis Procedures(Check sensor (1))
Read DTC
YES
Sensor Supply Voltage Sensor problem caused by supply voltage
Problem? to sensor. Locate the problem while dis-
NO
Check sensor wiring

NO
YES
NO
YES
Visually check sensor replace
NO
YES
NO
YES
Check ECU wiring
NO
YES
replace Check fuel system
AFFECTED VIN
DI10-167
TBD
P1608 ECU Malfunction
Read DTC
YES
ground wiring
NO
Check wiring
YES
NO
Repair completed
AFFECTED VIN
DI10-168
No Crank Signal
P0335 No Crank Signal MIL ON
Check sensor wiring
YES
YES
replace Trouble Continues? Replace APS
wheel
NO
NO
Check ECU wiring

Install new wheel
YES
YES
replace Trouble Continues? Replace ECU
NO
NO
Check wiring for open and

short
Repair completed
YES
NO
YES
sensor
NO
Install new sensor
AFFECTED VIN
DI10-169
High Torque Trim
P1170 High Torque Trim MIL ON
Read DTC
YES
IMV Related DTC? Refer to IMV
diagnosis
NO
Read DTC
NO
YES
Rail Pressure Sensor Repair or Check high pressure fuel
Problem? replace system
NO
YES
High pressure fuel system Repair or
Problem? replace
Check transfer pressure fuel
system
NO
YES
Transfer pressure fuel Repair or Replace ECU
system Problem? replace
* Refer to “Check High and Transfer pressure system”.
AFFECTED VIN
DI10-170
Glow Plug Module Communication Fault
P1676 Communication
P1677 Controller
Read DTC
NO
YES
Poor Glow Plug Communica-
Communication? tion problem Check wiring and insulation
between ECU
and glow plug
NO box. Check
YES
related wirings. Wiring Problem? Repair wiring
NO
YES
Wiring Problem? Repair or Replace glow plug box
replace
NO
YES
Check glow plug and wiring
(Resistance: below 1 Ω) NO
YES Repair completed

Problems? Repair or
replace glow
plug
NO
Check ECU wiring
YES
replace
AFFECTED VIN
DI10-171
Glow Plug Module Circuit Malfunction -

Open
P0671 Glow Plug #1
P0672 Glow Plug #2
P0673 Glow Plug #3
P0674 Glow Plug #4
P0675 Glow Plug #5
Read DTC
NO
YES
between ECU
and glow plug
NO
box. Check YES
NO
YES Replace glow plug box

replace
NO YES

Repair completed
YES
Problems? Repair or
replace glow
NO
plug
Check ECU wiring
YES
replace
AFFECTED VIN
DI10-172
Glow Plug Module Circuit Malfunction -

Short (B+)
P1671 Glow Plug #1
P1672 Glow Plug #2
P1673 Glow Plug #3
P1674 Glow Plug #4
P1675 Glow Plug #5
Read DTC
NO
YES
between ECU
and glow plug
NO
box. Check YES
NO
YES Replace glow plug box

replace
NO YES

Repair completed
YES
Problems? Repair or
replace glow
NO
plug
Check ECU wiring
YES
replace
AFFECTED VIN
DI10-173
TCU Signal Fault
P0700 TCU Signal Fault
Check ECU wiring
YES
replace
NO
YES
NO
Check CAN communication

(between High and Low: 120 Ω)
YES
Communication problem Repair or
continues replace
(Replace TCU)
NO
Repair completed
AFFECTED VIN
DI10-174
Air Conditioner Operating Circuit Fault
P1540 Open Circuit Unable A/C Operation
P1541 Short to +Batt Unable A/C Operation
P1542 Short to Ground Unable A/C Operation
Check vehicle condition

(above fault is related to A/C
system) NO
YES Check wiring and insulation

Switch without sensor? N/A
NO YES
Check sensor connection NO
YES Check A/C circuit and

Wiring Problem? Repair or compressor
replace
NO
YES
A/C Problem? Repair or
replace
Check sensor
NO
YES
Sensor Problem? Replace Replace sensor
sensor
NO
YES
Check ECU wiring
NO
YES
replace
AFFECTED VIN
DI10-175
Excessive Water in Fuel Filter
P1149 Excessive Water in Fuel Filter Water Separator Warning Light ON

Remove fuel filter
NO
YES
Water in fuel filter? Repair
completed Check ECU wiring
NO
YES
Check water detection sensor
replace
NO
YES
NO
YES
Check water detection
sensor wiring
NO
YES
replace
NO
Check resistance of water

detection sensor
YES
coolant
temperature
sensor
AFFECTED VIN
DI10-176
Immobilizer Malfunction
P1634 Immobilizer Malfunction MIL ON
P4335 Immobilizer Warning Light ON
P1630
P1631
P1632
P1633
P0633
P1636
Check immobilizer unit

and ECU wiring
YES
replace
NO
YES
Perform immobilizer coding Repair
again completed
NO
Repair or replace immobi-

lizer unit and related devices
AFFECTED VIN
DI10-177
FUEL SYSTEM DIAGNOSIS
OVERVIEW .............................................................. DI10-178

Fuel pressure system ......................................... DI10-179
Fuel system pressure test .................................. DI10-182
Fuel system check process ................................ DI10-184
AFFECTED VIN
DI10-178
FUEL SYSTEM DIAGNOSIS

OVERVIEW
When the Diagnostic Trouble Code (DTC) is detected through scan tool, it’s necessary to check the transfer and high
pressure fuel lines in fuel system before replacing the components.
If the trouble continues even after the trouble has been fixed with scan tool, must perform the fuel pressure test.
Below schematic diagram shows the specifications of pressure, flow mass and temperature in fuel system.
Transfer fuel Pressure limit valve

pressure regulator (High pressure line)
High pressure
Transfer pump pump
Supply
valve
Suction
valve
Below 2 bar
Over - 0.48 bar

Venturi Common rail
Up to
1600 bar
-0.6 ~ 0.1 bar
Injectors
Priming pump
Fuel filter
High pressure fuel

supply line
Transfer fuel supply line
Fuel tank Return line
Y220_10062
AFFECTED VIN
DI10-179
FUEL PRESSURE SYSTEM
Pressure/Volume Consumption in System Pressure/Volume Displacement from Pump
Conservation of fuel pressure/

volume (rail) for proper system
operation
Pump capacity for

supplying the required
target pressure/volume
Injector back
leak volume
Fuel injection
volume
Y220_10063
AFFECTED VIN
DI10-180
Example of Too Much Injector Back leak
Increased injector back leak volume
Pressure/volume loss
Injector back Pump capacity

leak volume
Fuel injection
volume
Pressure/volume Pressure/volume
consumption build up
Y220_10064
Too Much Injector Back leak

When the injector cannot be sealed due to entering the foreign materials
Ex.:
• Foreign materials in fuel
• Burnt out or worn high pressure pump
• Mechanical damage in inside of injector
AFFECTED VIN
DI10-181
Example of Pressure/Volume Loss in Pump
Decreased pressure/volume from

pump
Pressure/volume loss
Injector back
leak volume
Pump capacity
Fuel injection
volume
Pressure/volume Pressure/volume
consumption build up
Y220_10065
Pressure/Volume Loss in High Pressure Pump

When the required target pressure/volume cannot be delivered due to fuel supply line or pump damage
Ex.:
• Air in fuel supply line
• Excessive vacuum pressure in fuel supply line (-300 mbar)
• Burnt out or mechanically damaged pump
• Supply fuel with increased temperature ( > 65°C)
AFFECTED VIN
DI10-182
FUEL SYSTEM PRESSURE TEST

Test Tool Kit
For High Pressure Line
Y220_10066
For Transfer Line
Y220_10067
AFFECTED VIN
DI10-183
Prerequisite
1. Check the connections in fuel supply lines.
2. Check the fuel level in fuel tank.
3. Check if the air exists in fuel supply lines (air bubbles in fuel supply lines or fuel with air bubbles).
4. Check the fuel supply lines for leaks (transfer and high pressure).
5. Check if the specified fuel is used.
6. Check the fuel filter for contamination and abnormality.
Fuel System Test Process
Determine DTC
No Yes
DTC Detected?
No High pressure fuel Fuel system

related problem related DTC:
P1252, P1253,
P1254...P0251
no
Check and repair Diagnose and repair
transfer and H/P fuel Check fuel filter and H/P according to the de-
system fuel system tected DTC
Notice
If more than one DTC have been detected, check the wiring
harness for open or short first.
Check the transfer fuel system and fuel filter before
proceeding the high pressure fuel system check in next page.
AFFECTED VIN
DI10-184
FUEL SYSTEM CHECK PROCESS

Initial Check
• Transfer fuel system (air in system), specified fuel used
• Fuel leaks, fuel filter
• Diagnostic Trouble Code
• Wiring harness
• Abnormal noise from injector
No
No Abnormality Check and repair
in Initial Check?
Yes
Check fuel rail pressure (refer to 4-1)

When cranking engine for 5 seconds
after disconnecting IMV connector, is
the rail pressure over 1,050 bar?
Check transfer fuel system (refer to 4-2)

Yes Install the transparent tube between fuel
filter and priming pump. Check the trans-
fer fuel system for clogged or air bubbles.
Check if the vacuum pressure is proper.
No
* Thoroughly clean the components
before installation
Check the injector
back leak volume
Method 1 Method 2
Static Test for Injector Back leak Volume Dynamic Test for Injector Back leak Volume (refer to 4-4)
(refer to 4-3)
(with engine running)
(with engine cranking but not running)
1. Warm up engine (coolant temp.: over 60°C), place an
Place an empty plastic container under the return of empty plastic container under the return of injector, and
injector: start engine.
Remove IMV and injector connectors, crank for 5 2. Run the engine for 30 seconds at idle speed, perform :
seconds, and check the injector back leak volume. fuel system pressure leakage test” with Scan-i, and
The fuel length in tube should be over 20 cm. check the fuel level in container. It should be over 38 ml.
High Pressure Pump Test (refer to 4-5)

No Install the closed rail into high pressure No
pump at outlet port. Remove IMV connector
and crank engine for 5 seconds. Is the pres-
Yes Yes
sure over 1,050 bar?
Replace the injector Replace the injector

Enter new injector C2I data into ECU Enter new injector C2I data into ECU
after replacing the injector after replacing the injector
Perform the initial check again. Yes
No
Replace high pressure pump
AFFECTED VIN
DI10-185
4-1. High Pressure System Pressure Test
Fuel Rail Pressure Test

1. Disconnect the fuel rail pressure sensor connector and
IMV connector.
Y220_10068
2. Install the pressure tester in tool kit to the fuel rail

pressure sensor connector.
Y220_10069
3. Crank the engine for 5 seconds (twice).

- Read the maximum pressure displayed on the tester.
- If the maximum pressure is below 1,050 bar, refer to
“Fuel System Check Process” section.
Y220_10070
AFFECTED VIN
DI10-186
How To Use Pressure Tester

1. Check if the “TEST?” is displayed on the display when
pressing the “ ” button.
Y220_10071
2. The maximum pressure will be displayed when pressing

the button while cranking the engine (around 4 seconds
elapsed from 5 seconds).
Note
The fuel rail pressure can be measured through the scan
tool.
Y220_10072
AFFECTED VIN
DI10-187
4-2. Transfer Fuel System Test
Test Procedures
1. All wiring harnesses, connectors and fuel lines should
be installed properly and the engine should be ready to
start.
2. Prepare the special tools for transfer fuel system test
and thoroughly clean the system.
Y220_10073
3. Disconnect the key connector for connecting the priming pump to fuel filter and install both connectors of the
special tool to the fuel pump and the priming pump hoses.
Y220_10074
4. Start the engine and visually check the transfer line for clogged and air bubbles while running the engine at idle
speed.
5. If the fuel flows are not smooth or air bubbles are found in fuel lines, locate the leaking area and correct it.
AFFECTED VIN
DI10-188
4-3. Static Test for Injector Back leak Volume

1. Remove the injector return hose and seal the openings with screw type caps (included in tool kit).
Y220_10076
2. Install the hoses from back leak test containers to return

nipples of injector.
Y220_10077
3. Disconnect the IMV connector in H/P pump and the fuel

pressure sensor connector.
Y220_10078
AFFECTED VIN
DI10-189
4. Crank the engine twice with 5 seconds of interval.

5. Check if the back leak volume meets the specification.
Specified value Below 20 cm
Note
If the measured value is out of specified value, replace
the injector.
Y220_10079
AFFECTED VIN
DI10-190
4-4. Dynamic Test for Injector Back leak Volume

1. Start the engine and warm up until the coolant temperature reaches to 60°C.
2. Remove the injector return hose and seal the openings with screw type caps (included in tool kit).
Y220_10080
3. Install the hoses from back leak test containers to return

nipples of injector.
Y220_10081
4. Start the engine and let it run for 2 minutes at idle speed.
5. Check if the back leak volume meets the specification.
Specified value Below 38 ml
Y220_10082
AFFECTED VIN
DI10-191
PRESSURE LEAKAGE TEST WITH SCAN-100

1. When performing the static test for injector back leak Volume, the fuel pressure leakage test with Scan-i should be
done simultaneously. And, the fuel pressure leakage test with Scan-i can be done separately.
2. Test Conditions:
• No defective or faulty sensors and components in fuel system: checked by Scan-i
• Coolant temperature: over 60°C
3. The diagnosis procedures with Scan-i are as below:
1) Install the Scan-i to the diagnostic connector. Select

“DIAGNOSTICS” and press “ENTER” in “MAIN MENU”
screen. Select “REXTON” and press “ENTER” in “VEHICLE
2) Select “ECU” and press “ENTER” in “CONTROL UNIT

3) Select “LEAK DETECTION” and press “ENTER” in

AFFECTED VIN
DI10-192
4) If there are not any troubled conditions in “TEST

CONDITION” screen, press “ENTER”.
AFFECTED VIN
DI10-193
4-5 High Pressure Pump Test

1. Prepare the special tools for high pressure pump test
and thoroughly clean the system.
Y220_10083
2. Remove the high pressure fuel supply pipe and install

the closed rail delivered with tool kit.
Specified value 40 Nm
* The figure is to show the test method. However, the

actual test operation should be done while the high
pressure pump is installed in vehicle.
Y220_10084
3. Install the opposite end of the closed rail into the fuel rail
for test.
Specified value 40 Nm
Y220_10085
4. Remove the high pressure fuel return hose and install

the transparent tube between the high pressure pump
and the return port of fuel rail for test.
Y220_10086
AFFECTED VIN
DI10-194
5. Connect the digital tester connector into the sensor

connector of fuel rail for test.
6. Disconnect the IMV connector and the fuel rail pressure
sensor connector.
7. Check if the measured value on the digital tester meets
the specified value.
Specified value Over 1,050 bar
Y220_10087
Y220_10088
AFFECTED VIN
REXTON (1 OF 2)
ENGINE SERVICE MANUAL
ISSUED BY
INTERNATIONAL A/S TEAM
SSANGYONG MOTOR CO., LTD.
150-3, CHILGOI-DONG, PYUNGTAEK-SI

GYEONGGI-DO, 459-711 KOREA
TELEPHONE : 82-31-610-2740
FACSIMILE : 82-31-610-3762
NOTE:All rights reserved. Printed in SSANGYONG Motor Co., Ltd.

No part of this book may be used or reproduced without the
written permission of International A/S Team.

Rexton - Service Manual - ENGINE PDF

Uploaded by

Copyright:

Available Formats

Rexton - Service Manual - ENGINE PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rexton - Service Manual - ENGINE PDF

Uploaded by

Copyright:

Available Formats

ENGINE

MANUAL(vol. 1 of 2) GENERAL INFORMATION DI0A

REXTON ENGINE ASSEMBLY DI01

ENGINE HOUSING DI02

INTAKE SYSTEM DI03

This manual includes procedure for maintenance, EXHAUST SYSTEM DI04

FUEL SYSTEM DI07

ENGINE CONTROL SYSTEM DI08

ELECTRIC DEVICES AND

SSANGYONG MOTOR CO., LTD.

GENERAL INFORMATION .................... DI0A

ENGINE ASSEMBLY ............................. DI01

EXHAUST SYSTEM............................... DI04

FUEL SYSTEM ...................................... DI07

DIAGNOSIS ........................................... DI10

CLEANNESS ....................................... DI0A-3 FUEL SYSTEM ................................. DI0A-21

STRUCTURE ...................................... DI0A-8 Fuel supply system ...................... DI0A-22

GENERAL INFORMATION CHANGED BY

Cleanness of DI Engine Fuel System and Service Procedures

Valve actuator lift: 0.028 mm

GENERAL INFORMATION CHANGED BY

2. Always keep the tools clean (from oil or foreign materials).

Carefully listen the symptoms and problems from customer.

Perform the diagnosis proceee with Scan-i

Clean the engine compartment before starting service works.

CHANGED BY GENERAL INFORMATION

Disconnect the negative battery cable.

Fuel pressure sensor

High pressure pump Common rail

GENERAL INFORMATION CHANGED BY

7. Plug the removed components with clean and

9. To supply the fuel to transfer line of HP pump press

Do not crank engine before having filled pump.

10. Check the installed components again and connect

CHANGED BY GENERAL INFORMATION

DI Engine and Its Expected Problems and Remedies Can be Caused

SYSTEM SUPPLEMENT AGAINST PARAFFIN SEPARATION.

SYSTEM SUPPLEMENT AND REMEDY AGAINST WATER IN FUEL

GENERAL INFORMATION CHANGED BY

CHANGED BY GENERAL INFORMATION

GENERAL INFORMATION CHANGED BY

Left side view

Right side view

CHANGED BY GENERAL INFORMATION

HFM sensor/intake air Pre heating time relay Main relay

GENERAL INFORMATION CHANGED BY

ENGINE AND SENSORS

Glow plug Fuel pressure sensor

Camshaft position Booster pressure sensor

HP pump Coolant temperature Knock sensor (2)

CHANGED BY GENERAL INFORMATION

ELECTRICAL COMPONENTS AND PRE HEATING SYSTEM

Glow plug Pre heating time relay

Fuse box Battery

Starter motor Alternator

GENERAL INFORMATION CHANGED BY

Intake outlet hose Turbocharger Intercooler Inlet hose

CHANGED BY GENERAL INFORMATION

INTAKE AIR FLOW CHART