Tructural Alculations: Project Name1

© MasterSeries PowerPad - Project Title 494303486.
docx
STRUCTURAL CALCULATIONS
Using
MASTERSERIES POWERPAD
Project Name1
Address 1
Address 2
Address 3
ARCHITECT
ARCHITECT NAME
Location
Location
Location
STRUCTURAL ENGINEERS
© Civil and Structural Computer Services Limited, 1 Circular Road, Newtownabbey, Co. Antrim BT37 0RA, Tel : 028 9036 5950 Fax : 028 9036 5102
© MasterSeries PowerPad - Project Title 494303486.docx
MASTERSERIES SAMPLE OUTPUT

to place your title block here ensure you have copied your personal
TABLESWD.OVR file to the MasterSeries application directory.
In Word 2007 specify the MasterSeries app dir in Trusted Loactions
PROJECT NO: P12345
December 1997
V.A.T. Reg. No. ___ ____ __
 C:\PROGRAM FILES (X86)\MASTERSERIES\MASTER\SAMPLE MOMENT AND SIMPLE CONNECTIONS.IMJ
BASE-PLATE
Base-Plate Connection
LOADING CASE 001
Basic Data
Applied Forces at Interface
Resultant Forces M, Fv, F Moment +0.0 kNm, Shear +19.6 kN, Axial -42.3 kN
(Axial Up-Lift)
Basic Dimensions
Column: 139.7x6.3CHS [28] Ø=139.7, T=6.3, py=275
Data grout, Fcu, Fcv, py, slope 25 N/mm², 30 N/mm², 0.35 N/mm², 265 N/mm², 30 deg to vertical
Design to BS 5950-1: 2000 and the SCI Green Book:
Joints in Steel Construction : Moment Connections: SCI-P-207/95
Column Capacities Mc, Fvc, Fc 27.8 kN.m, 261.4 kN, 726.1 kN Fvc = 261.4 kN OK
Summary of Results (Unity Ratios)

Bolt Tension 0.16 OK
Plate Tension Bending 0.60 0.60 OK
Concrete Embedment 0.17 OK
Washer Bending & Shear 0.00, 0.05 0.05 OK
Pullout Cones 0.02, 0.03, 0.05 0.05 OK
Horizontal Shear 0.09 OK
Weld 0.05, 0.08, 0.01 0.08 OK
Step 1: Base-Plate Pressure

No Net Compression Tension Only
Bolt Ecc=L-Lcent-Rcent 400.0 - 50.0 - 50.0 300.0 mm
Fmom=M/Bolt ecc 0.0/300.0 0.0 kN
Bolt Force=Fa/2+Fmom 42.3/2 + 0.0 (per side) 21.2 kN
Bolt Capacity=0.8•pt•No.Bolts 0.8•84.7•2 135.6 kN OK
Step 2b: Plate Tension Bending

m=(Rmax-D/2) (212.1 - 139.7/2) 142.3 mm
Le=Lei+2•m <= B <= Pi•D/2 109.7 + 2•142.3 <=400 <= Pi • 139.7 / 2 219.4 mm
mt=(T•n)•m (10.6•2)•142.3 3.0 kN.m
tp=√(4•mt/py/Le) √(4•3.0/265/219) 14.4 mm OK
Step 3: Bolt Pullout

Washer Embedment
Min Embedment Fn(Ft, Void, Fbear) 10.6, 50,30 1.7 mm
Actual Embedment (70 - 50)/2 10.0 mm OK
Washer Shear and Bending

Washer Force per Bolt 10.58 kN
Washer Bending Fn(py, ts, Le, ø') 275, 12, 25, 14.0 Void <= 1.7Ø + 2t n/a
Washer Shear Cap=Ø•pyq•0.9•t (1.7•24•)(0.6•275)•0.9•12 228.4 kN OK
Individual Cones
Limit Washer width Lap=5•t/0.6 5•12/0.6 100.0 mm
Force per Bolt 10.58 kN
Capacity Fn(w, Slope, h, Pyq) 70.0, 30°, 788, 0.35 544.35 kN OK
Single Cone
Total Bolt Force 21.15 kN
Capacity Fn(w, d, Slope, h, Pyq) 70.0, 370.0, 30°, 788, 0.35 735.43 kN OK
Single Cone on All Bolts

Total Bolt Force 42.30 kN
Capacity Fn(w, d, Slope, h, Pyq) 370, 370, 30°, 788, 0.35 926.51 kN OK
Note Minimum distance from any tension Bolt to free edge 490 mm
If less then pullout cone shear capacity will be reduced
Step 4: Shear
Base Friction
Friction Fr=0.30•Fc 0.30•-42.3 kN uplift therefore ignore 0.0 kN
Bolt Bearing
Bolt Shear Bs=Fn(ShrCap, tg) 56.5, 24 56.5 kN
Concrete Bearing Cb=6•Ø²•Fcu 6•24²•25 86.4 kN
Plate Bearing Pb=Fn(pb,e,Ø,t,kbs) 460, 50, 24, 24, 0.70 185.5 kN
Bolt Bearing Bb=pb•Ø•tk 460•24•24 265.0 kN
Bsten=min(1, 1.4 -Ft/(0.8•Pt))•Bs min(1, 1.4 - 21.2) /(0.8•169.4))•56.5 56.5 kN
Pts=Min(Bsten, Cb, Pb, Bb)•nbt Min(56.5, 86.4, 185.5, 265.0) = 56.5•4 225.9 kN
Total Shear Capacity

Total Cap=Pts 225.9 225.9 kN OK
Step 5: Weld
Axial Load Fa=F/(pi•D) -42.3/(3.14•139.7) -0.10 kN/mm
Moment load Fm=M/(D•D) 0.0/(139.7•139.7) 0.00 kN/mm
Shear load Fv=V/(pi•D) 19.6/(3.14•139.7) 0.04 kN/mm
Direct Bearing therefore design for tensile forces only.
Fapp=Fa 0.10 0.10 kN/mm
Shear (Longitudinal)
Fcap w=1•0.7•leg•Py 1•0.7•6•220 0.92 kN/mm OK
Tension (transverse)
Fcap w=1•0.7•leg•Py 1•0.7•6•275 1.16 kN/mm OK
Combined
Comb (Ft/Pt)²+(Fl/Pl)²<1 (0.10/1.16)² + (0.04/0.92)² 0.01 OK

Tructural Alculations: Project Name1

Uploaded by

Copyright:

Available Formats

Tructural Alculations: Project Name1

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tructural Alculations: Project Name1

Uploaded by

Copyright:

Available Formats

© MasterSeries PowerPad - Project Title 494303486.

MASTERSERIES SAMPLE OUTPUT

TABLESWD.OVR file to the MasterSeries application directory.

In Word 2007 specify the MasterSeries app dir in Trusted Loactions

PROJECT NO: P12345

V.A.T. Reg. No. _

 C:\PROGRAM FILES (X86)\MASTERSERIES\MASTER\SAMPLE MOMENT AND SIMPLE CONNECTIONS.IMJ

LOADING CASE 001

Summary of Results (Unity Ratios)

Step 1: Base-Plate Pressure

Step 2b: Plate Tension Bending

Step 3: Bolt Pullout

Washer Shear and Bending

Single Cone on All Bolts

Total Shear Capacity

You might also like