Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 215 views

    Product Specification Sheet BELZONA 5891: General Information

    Uploaded by

    Mohamed Nouzer

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Product Specification Sheet BELZONA 5891: General Information

    Uploaded by

    Mohamed Nouzer
    215 views4 pages

    Original Title

    BELZONA 5891.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    215 views4 pages

    Product Specification Sheet BELZONA 5891: General Information

    Uploaded by

    Mohamed Nouzer

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    PRODUCT SPECIFICATION SHEET

    BELZONA 5891
    FN10105

    GENERAL INFORMATION

    Product Description:
    A two component, epoxy/amine system containing mineral and ceramic fillers. Provides excellent corrosion resistance when immersed in
    water/hydrocarbon mixtures up to 194°F(90°C). Applied by brush or heated airless spray. May also be applied by injection to create irregular shims.

    Application Areas:
    When mixed and applied as detailed in the Belzona Instructions for Use (IFU), the system is ideally suited for application to the following:

    - Effluent tanks and channels - Condensers - Condensate tanks


    - Water boxes - Knock out drums - Strippers and scrubbers
    - Separators - Evaporators

    APPLICATION INFORMATION

    Working Life Base Component


    Will vary according to temperature. At 68°F (20°C) the usable life of Appearance Viscous liquid
    mixed material is 45 minutes. Color Grey
    Density 1.75 - 1.79 g/cm3
    Coverage Rate
    The Belzona 5891 shall be applied to achieve a minimum thickness of Solidifier Component
    16 mils (400 microns). At this thickness the theoretical coverage rate is Appearance Thin liquid
    27sq.ft. (2.5 m2)/litre. Color Amber
    Refer to the Instructions For Use for practical coverage rate guidelines. Density 0.95 - 0.99 g/cm3

    Cure Time Mixed Properties


    Allow to cure for the times shown in the Belzona IFU before subjecting Mixing Ratio by Weight (Base : Solidifier) 13 : 1
    it to the conditions indicated. Mixing Ratio by Volume (Base : Solidifier) 7.2 : 1
    Density 1.65 - 1.69 g/cm3
    In certain instances it may be necessary to post cure material prior to Time to peak exotherm 125-160 mins.
    putting into service where chemical contact is involved or service Peak exotherm temperature 122-149°F (50-65°C)
    temperature is below 86°F (30°C). Viscosity 55-65 poise
    Sag resistance >25 mil (635 micron)

    The above application information serves as introductory guide only. For full application details including the recommended application
    procedure/technique, refer to the Belzona IFU which is enclosed with each packaged product.

    Belzona 5891 - Product Specification Sheet www.belzona.com Publication No. 67-08-16


    Page 1 of 4
    PRODUCT SPECIFICATION SHEET
    BELZONA 5891
    FN10105

    ADHESION FLEXURAL STRENGTH

    Tensile Shear When tested to ASTM D790 typical values obtained are:
    When tested in accordance with ASTM D1002, using mild steel, grit
    blasted to a 3-4 mil profile, typical values are: 6,500 psi (44.82 MPa) ambient cure
    9,600 psi (66.19 MPa) post cure
    2,690 psi (18.54 MPa) ambient cure
    3,470 psi (23.92 MPa) post cure
    3,350 psi (23.10 MPa) post cure and tested at 212°F (100°C)
    HARDNESS
    Pull Off Adhesion
    When tested in accordance with ASTM D4541/ ISO 4624, the pull off
    strength from grit blasted steel will be typically: Shore D
    The Shore D hardness of the material when tested to ASTM D2240 is
    4,800 psi (33.09 MPa) ambient cure typically:
    5,700 psi (39.30 MPa) post cure
    87 ambient cure
    87 post cure

    CATHODIC DISBONDMENT Koenig Pendulum


    When tested to ISO 1522 the Koenig damping time of the coating will
    be typically:
    When tested in accordance with ASTM G42 at 158°F (70°C) the
    disbondment diameter is typically 0.4 in (10.2mm). 85 seconds ambient cure
    142 seconds post cure

    CHEMICAL RESISTANCE
    HEAT RESISTANCE
    The material will demonstrate excellent resistance to a broad range
    of chemicals. Heat Distortion Temperature
    Tested to ASTM D648 (264 psi fiber stress), typical values obtained
    * For a more detailed description of chemical resistance properties, will be:
    refer to relevant Chemical Resistance chart.
    124°F (51°C) ambient cure
    252°F (122°C) post cure

    COMPRESSIVE STRENGTH Heat Resistance


    Atlas Cell
    When tested in accordance with NACE TM 0174 the coating will
    When tested in accordance with ASTM D695, typical values obtained exhibit no rusting (ASTM D714 rating 10) or blistering (ASTM D610
    are: rating 10) after 6 months immersion in water at 194°F (90°C).

    13,800 psi (95.15 MPa) ambient cure Seawater immersion


    20,000 psi (137.90 MPa) post cure When tested in accordance with ISO 2812, no blistering, rusting,
    cracking or delamination was observed after 6 months immersion in
    seawater at 104°F (40°C).

    ELECTRICAL PROPERTIES Steam-out Resistance


    Once fully cured the coating will exhibit no blistering, cracking or
    When tested in accordance with ASTM D149, method A, with voltage delamination after 96 hours exposure to pressurised steam at 410°F
    rise of 2kV/s, typical value will be: (210°C).
    Dielectric strength 31.8 kV/mm
    Dry Heat Resistance
    The indicated degradation temperature in air based on Differential
    Scanning Calorimetry (DSC) operated in accordance with ISO11357 is
    EXPLOSIVE DECOMPRESSION typically 446°F (230°C).
    For many applications the product is suitable down to -40°F
    (-40°C).
    When tested to NACE TM 0185, using a seawater/hydrocarbon test
    fluid, the coating will exhibit no breakdown after a 21 day immersion
    period at 158°F(70°C) and 70 bar pressure followed by
    decompression over 15 minutes.

    Belzona 5891 - Product Specification Sheet www.belzona.com Publication No. 67-08-16


    Page 2 of 4
    PRODUCT SPECIFICATION SHEET
    BELZONA 5891
    FN10105

    IMPACT RESISTANCE THICK FILM CRACKING

    Izod Impact Strength When tested in accordance with Section 12 of NACE TM0104, the
    The Izod impact strength of the material when tested in accordance coating at three times recommended thickness, exhibited no
    with ASTM D256 is typically: cracking after 12 weeks immersion in seawater at 104°F (40°C).

    Notched Un-notched
    27 J/m 29 J/m ambient cure
    48 J/m 83 J/m post cure SHELF LIFE

    Separate base and solidifier components shall have a shelf life of


    THERMAL PROPERTIES 5 years from date of manufacture when stored in their original
    unopened containers between 32°F (0°C) and 86°F (30°C).

    Low Temperature Thermal Shock


    Coated steel panels will exhibit no blistering, cracking or
    delamination after multiple cycles of rapid cooling from 212°F APPROVALS/ACCEPTANCES
    to -76°F (100°C to -60°C).

    Thermal Cycling The material has received recognition from organizations worldwide
    When tested in accordance with section 9 of NACE TM0304, the including:
    coating passed after 252 cycles between +140°F and -22°F (+60°C
    and -30°C). USDA

    Belzona 5891 - Product Specification Sheet www.belzona.com Publication No. 67-08-16


    Page 3 of 4
    PRODUCT SPECIFICATION SHEET
    BELZONA 5891
    FN10105

    WARRANTY

    Belzona guarantees this product will meet the performance claims stated herein when material is stored and used as instructed in the Belzona
    Information For Use leaflet. Belzona further guarantees that all its products are carefully manufactured to ensure the highest quality possible and
    tested strictly in accordance with universally recognised standards (ASTM, ANSI, BS, DIN, ISO etc.). Since Belzona has no control over the use of
    the product described herein, no warranty for any application can be given.

    AVAILABILITY AND COST MANUFACTURER

    Belzona 5891 is available from a network of Belzona Distributors Belzona Polymerics Ltd. Belzona Inc.
    throughout the world for prompt delivery to the application site. For Claro Road, Harrogate, 2000N.W. 88th Court,
    information, consult the Belzona Distributor in your area. HG1 4DS, UK Miami, Florida, USA, 33172

    HEALTH AND SAFETY TECHNICAL SERVICE

    Prior to using this material, please consult the relevant Material Complete technical assistance is available and includes fully trained
    Safety Data Sheets. Technical Consultants, technical service personnel and fully staffed
    research, development and quality control laboratories.

    The technical data contained herein is based on the results of long term tests carried out in our laboratories and to the best of
    our knowledge is true and accurate on the date of publication. It is however subject to change without prior notice and the Belzona products are
    user should contact Belzona to verify the technical data is correct before specifying or ordering. No guarantee of accuracy is manufactured under an
    given or implied. We assume no responsibility for rates of coverage, performance or injury resulting from use. Liability, if any,
    is limited to the replacement of products. No other warranty or guarantee of any kind is made by Belzona, express or implied, ISO 9001 Registered
    whether statutory, by operation of law or otherwise, including merchantability or fitness for a particular purpose. Quality Management System
    Nothing in the foregoing statement shall exclude or limit any liability of Belzona to the extent such liability cannot by law be
    excluded or limited.

    Copyright © 2016 Belzona International Limited. Belzona® is a registered trademark.

    Belzona 5891 - Product Specification Sheet www.belzona.com Publication No. 67-08-16


    Page 4 of 4

    You might also like