Indian Standard: Methods of Test For Aggregates For Conci

Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata(anuradhapatra84@gmail.com) 42.110.148.147 [for non-commercial use only].
IS : 2386 ( Part VI) - 1963

(Reaffirmed 2011)
(Reaffirmed 2016)
Indian Standard
METHODS OF (Reaffirmed 2015)
TEST FOR AGGREGATES FOR CONCI
PART VI MEASURING MORTAR MAKING PROPERTIES
OF FINE AGGREGATE (Reaffirmed 2014)

Tenth Reprint APRIL 2006
( Including Amendment No.1 and 2 ) (Reaffirmed 2013)
(Reaffirmed 2012)
(Reaffirmed 2011)
(Reaffirmed 2010)
(Reaffirmed 2009)

© Copyright 1963 (Reaffirmed 2008)
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
(Reaffirmed 2007)
Gr 2 October 1963

(Reaffirmed 2006)
IS J 1386 ( Part VI ) • 1963
Indian Standard
METHODS OF TEST
FOR AGGREGATES FOR CONCRETE
PART VI MEASURiNG MORTAR MAKING PROPERTIES
OF FINE AGGREGATE
Cement and Concrete Sectional Committee, BDC 2

Chairman Representing
~llRI K. K. NAMBIAR The Concrete Association of India, Bombay
Members
~HRI K. V. TltADA-SEY ( Alternate to
:Shd K. K. Narnbiar )
~ll.lU K. F. Ax'rIA 1\1. N. Dastur & Co Private Ltd , Calcutt»
SHIH 1'. :S. BHA'.rNAGAR Bhakra Dam Designs Directorate, Kew D6Jhi
Du I. C. Dos 1\1. PAIS CUDDOU Central '\\,Yater & Power Commission ( Miuil:itry of
Irrigation & Power )
~J(UI Y. K. MURTHY ( Alternate)
~Hltl N. D. DAFTABY Khira Steel Works Private Ltd, Bombay
8HRI N. G. DEWAN Central Public "'Yorks Department
SUPERINTENDING ENGINEER,
2:-iD CIRCLE ( Alternate)
DJ~ R. R. H ATTIANGADI The Associated Cement-Companies Ltd , Bombay
8HBI V. N. PAl ( Alternate)
SURI J}. C. HAZRA Geological Survey of India, Calcutta
JOINT DIREc'rOR STAXDARDS Research, Designs & Standards Organization
(B& S) ( Ministry of Railways)
ASSISTANT DIRECTOR STAND-
ARDS ( B & S ) ( Alternate )
SUBI S. B. JOSHI S. B. Joshi & Co Private Ltd, Bombay
SHIU 1\1.1\1. LAL U. P. Government Cement Factory, Churk
~HRI B. N. l\IAJUl\IDAR Directorate General of Supplies &; Disposals ( Mini.-
try of Economic & Defence Co-ordination)
SURI P. L. DAB ( Alternate)
!lUO}' S. It. ~lEHRA Central Road Research In.stitute (CSIR), New
Delhi
8HBI X. H. l\IOlIILE The Concrete Association of India, Bombay
SHIU S. N. ~IUKERJI Government Test House, Calcutta
~HIU N. C. Sl!.:N GUPTA ( Alternate)
8HBI EBACH A. N ADIRSHAH Institution of Engineers ( India ), Calcutta
~UBI C. n, PATEL National Buildings Organisation (Minist.ry of
Works, Housing & Rehabilitation)
SURI RABINDl!;R SINGH ( Alternate )
PROF O. S. IlAMAs\\'AMY Central Building Research Institute (CSIR),
Roorkee
SURI K. SIVA PRASAD ( Alternate)
SHUI T. N. 8. RAO Gammon India Limited, Bombay
:::>HRI S. R. PlliHElRO (Alternate)
( Continued on page 2 )

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARO
NEW DELHI 110002
18 I 2386 ( Part VI ) • 1963

( ColIIllJllea from page 1 )
Mtmbers Reprtst1lnng
RxpaalCNTATIVP: ~Itll,tin
Burn Ltd, Calcutta
~HRI NIHAB CHANDRA Roy Dulmia Cement C Bharar ) Ltd, Calcutta
~E(;BETAR" Oentral Boord of Irrigatiou & Power ( l\Iinistl'Y of
Irrigation & Power )
HRIG G. S. SIROTA Ellgilloer-in·Chief's Branch, .:\1'1l1~P Headquarters
R, 8. 11~~liA:NDnu ( Alternate )
'-iRBI
DR BH. SUDRARAJV Indian RO~l(.l., Congress, 'Now Delhi
SHRI J. 11. TR};}IAN Roads \\"jug, )Iiuiat I'Y of 'I'ransport &. Conuuuui-
vat icue
8){RI ~. H, KK8WA~1 ( Alternate )
VB H. C. VISVJo;SVABAYA, Director, BIS, ( Ex-officio Member )
Deputy Director ( Bldg)
Secretary
SHut A. PRI'!'HIVI IL\"
ExtrB Assistant Director ( Bldg ), BIS
Concrete Subcommittee, BDC 2 : 2
Convener
SHRI S. B. JOSHI S. B, Joshi & Co Private Ltd, Bombay
Members
ASSISTANT DIREC1.'On S·.rA~D- Research, Designs & Standards Organization
ABDR ( B & s ) ( l\Iinistry of Railways)
SUBI N. H. nH AOW AN A~I Engineer- in-Chief''s Branch, Army Headquarters
Du I. C. Dos M. PAIS Cunnou Central Wo,ter & Power Connuissicn (Ministry of
Irrigution & POW01' )
~Hal Y. K. :\IuR1.'uy ( Alternate)
~HBI P. IJ. DA~ Directorate General of Supplies & Diepoaels
( Ministry of BCUIlOIUic & Defence Co-ordlna-
tion)
SKRI D. x, ~IAJ UMDAR ( Alternate)
DIRECTOR Enginoering H,08CUl'eh LU),Ol'UtOl'y, Hyderabad
SURI V. N. GUNAJI Mahareshtra Public 'Yorks Department
:SHBI1\1. A. HAJ'EEZ National Buildings Organisation (}linistl'y of
Works, Housing & Rehabilitation )
SKBI B. S. SHIVA~UR'r"Y ( Alternate )
~.HRI C. I~. HANDA Central "-nLer & Power Commiasion ( ~Iillistry of
Irrjgation & Power )
SKat P. e. HAZRA Goological Survey of Fndin, Calcut.ta
~HRI K. K. ~AMBl.\R 'I'he Concrete Associutiou of India, BOlnUt\Y
SH RX C. L. N. I Yl!:SOAR (Allt!rllale )
Va M. I". PURl Central Road Research Institute (CSIR), New
Delhi
1)gol' G.~, RAMA8\vluy Central Building Rcseurch Inatituto (CSIR),
Roorkee
~HRI K. Hlv.\. PBASAU ( ..Alternate )
5MBI T. N. 8. RAO Gammon India Ltd , Bouibuy
SHBt S. R. PIS lIll:IRO ( Alternate)
SU.PERINT~NDl.NG ENOINb:ER, Central Public 'VorkH Department
2~D CIRCLE
SHIll O. P.
GOEL ( Alternate )
SKIll J. M. TBEHAN Roads \Ving. J\linjstry of Transport & Communica-
tions
SHBI R. P. SlICK A ( Alternate )
SHBI H. 'r. YAN Braithwaite Burn & Jessop Construction Co Ltd,
Calcutta
2
AMENDMENT NO. 1 FEBRUARY 1982

TO
IS:2386(Part VI)-1963 METHODS OF TEST FOR
AGGREGATES FOR CONCRETE
Part VI MEASURING MORTAR MAKING PROPERTIES
OF FINE AGGREGATF
-----
Alteration
[Page B~ claus.. ? and ?1 (zagnumbered as 8 and
8.1)] - Substitute the following tor the existing
clauses:
,8 • REPORTING 01 RESULT
8.1 CaJ.culate the average crushing strength or Dot

less than three specimens containing untreated sand.
Similarly calculate the average crushing strength of
the corresponding number ot specimens containing
treated sand. Report the average crushing strength
ot specimens containing untreated Band as a percentage
ot the average crushing strength or the speelmen8
containing treated sand.'
Addend!!!
(Page 4 ~ claws. 1.1) - Add tbe tollowing DeY
clauses after 1.1 and renumber the clauses '2 to T' &s
'3 to 8':
"2 • BASIS rOR COMPARlSOB
2.1 The rine aggregate shllll be compared 1n !IOrter,

&S deserlbed in this methoti. with a sample or the same
aggregate that has been washed in a 3 percent solution
of sodium hydroxide folloved by thorough rinsing in
vater. The treatment shall be repeated till the
¥ashed material produces a colour lighter than that or
the at&Dd&r4 801utioD d••crlbe4 in 6.2.2 ot

rS:2386(P&rt 11)..1963 'Methods of telt tor agreptea
tar coacrete : Part II Eatl..tloD ot deleterious
materials &Del organic lmpurltiea'. Bowever, it .ball
be ensured that DO tine. are lOlt vIlile va.hiDS vi th
aodiwa h)rdroxide. The vaahed aDd r1Dsed aggrepte
ahall be ehecked with a lu1table indicator Iuch ..
phenolphtbaleiD or l1t.u. to •••ure that all trace.
of sodium h7dronde are re8)Yed tro. the aggrepte
betore being u.ed tor -.tiDS cODtrol .,rtar."
(BDe 2)
Printed at Prabhat Offset Press, New Delhi-2

AMENDMENT NO.2 OcrOBER 1991

TO
IS 2386 ( Part 6) : 1963 METHODS OF TEST FOR
AGGREGATES FOR CONCRETE
PART 6 MEASURING MORTAR MAKING PROPERTIES OF FINE

AGGREGATE
t Pag« 4, clause 1.2 ) - Substitute the following for the existing clause:
•2.1 Tamping liar - The tamping bar shall be made of nor-absorbent, abrasion
resistant, non-brittle material such as a rubber compound having a Shore A
durometer hardness of 80 ± 10 or seasoned teak wood rendered non-absorbent
0e
by immersion for 15 minutes in paraffin at approximately 200 and shall have a
cross-section of 12.5 x 25 mm and a convenient length of 125 to 150 mm. The
tamping face shall be flat and at right angles to the length of the bar.'
( Page 4, clause 1.4 ) - Substitute the following for the existing clause:
"Z.4 Moulds - These shall be 50 mm cube moulds and shall conform 10 the
requirements laid down in IS 10036 : 19M2 'Specification for moulds for use in
tests of cement and concrete'."
( Page 5, clause 3.1, NOlt: ) - [klete.
( Page 5, clause 5.1, line 2) - Substitute '50 nun' for '7.06 crn '.
(CED 2)
Printed at Prabhat Offset Press, New Delhi-2

IS I 2386 ( Part VI ) • 1963
Indian Standard
METHODS OF TEST
FOR AGGREGATES FOR CONCRETE
PART VI MEASURING MORTAR MAKING PROPERTIES
OF FINE AGGREGATE
o. FOR E W 0 R D
0.1 This Indian Standard ( Part VI ) was adopted by the Indian Standards
Institution on 13 September 1963, after the draft finalized by the Cement
and Concrete Sectional Committee had been approved by the Building
Division Council.
0.2 One of the major contributing factors to the quality of concrete is
the quality of aggregates used therein. The test methods given in this
standard are intended to assist in assessing the quality of aggregates. In a
given situation, for a particular aggregate, it may not be necessary to
assess all the qualities and therefore it is necessary to determine beforehand
the purpose for which a concrete is being used and the qualities of the
aggregate which require to be assessed. Accordingly, the relevant test
methods may be chosen from amongst the various tests covered in this
standard. For the convenience of the users, the test methods are grouped
into the following eight parts of Indian Standard Methods of Test for
Aggregates for Concrete ( IS : 2386 - 1963):
Part I Particle Size and Shape
Part II Estimation of Deleterious Materials and Organic
Impurities
Part III Specific Gravity, Density, Voids, Absorption and
Bulking
Part IV Mechanical Properties
Part V Soundness
Part VI Measuring Mortar Making Properties of Fine Aggregate
Part VII Alkali Aggregate Reactivity
Part VIII Petrographic Examination
0.3 The Sectional Committee responsible for the preparation of this standard
has taken into consideration the views of the concrete specialists, testing
authorities, consumers and technologists and has related the standard to the
practices followed in this country. Further, the need for international
co-ordination among standards prevailing in different countries of the world
has also been recognized. These considerations led the Sectional
3
18 I 2386 ( Part VI ) • 1963
Committee to derive assistance from C 87 - 62T Tentative Method of Test

fer Measuring Mortar Making Properties of Fine Aggregate issued hy
American Society for Testing and Materials.
0.4 Wherever a reference to any Indian Standard appears in this method, it
shall be taken as a reference to its latest version.
0.5 For the purpose of deciding whether a particular requirement of this
standard is complied with, the final value, observed or calculated, expres-
sing the result of a test or analysis!' shall be rounded off in accordance with
IS: 2-1960 Rules for Rounding Off Numerical Values (Revised). The
number of significant places retained in the rounded off value shou ld be the
same as that of the specified value in this standard.
0.6 This standard is intended chiefly to cover the technical provisions
relating to testing of aggregates for concrete, and it does not include all the-
necessary provisions of a contract.
1. SCOPE
1.1 This standard (Part VI) covers the test procedure for measuring the
mortar-making properties of fine aggregate for concrete by means of
a compression test on specimens made from a mortar of a plastic consistency
and gauged to a definite water-cement ratio.
2. APPARATUS
2.1 Flow Table and Flow Mould - These shall conform to the require-
ments specified in 12 of *'IS: 1727· 1960 Methods of Test for Pozzolanic
Materials.
2.2 Tamper - It shall be made of a non-absorptive, non-abrasive material,
such as medium-hard rubber or seasoned oak wood rendered non-absorptive
by immersion for 15 minutes in paraffin at approximately 200°C and shall
have a cross-section of 12· 5 X 25 mm and a convenient length from 125 to
150 rom. The tamping face of the tamper shall be flat and at right angles
to the length of the tamper.
2.3 Trowel- It shall have a steel blade 100 to 150 mm in length, with
straight edges.
2.4 Mould. - These shall be 7·06 em cube moulds.
2.5 Tampiag Rod - It shall be approximately 10 mm in diameter and
100 rom long, with one end rounded to a hemispherical tip 10 mm
dia X approx 300 mm long.
2.6 Testing Machine - A compression testing machine of suitable capa-
city shall be used.
4
III 1116 (Part VI) • 1963
3. YOIlTAIl
3.1 Place cement and water in quantities that will give a water-cement ratio
of n·fi by weight in an appropriate vessel and permit the cement to absorb
water for one minute. Mix the materials into a smooth paste with a spoon.
Beat into the mixture a known weight of the sample of sand under test that
has been brought to a saturated surface-dry condition. Mix until the
material appears to be of the desired consistency t flow 100 ± 5). Oontinue
the mixing for 30 seconds and make a determination of the flow in
accordance with 4.
NOT. - }'or six '·00 eru cubes 1830 II or loeUlent and uno g of wawr will u.ualll
give ~"ft'l~iellt nlort.\r. 'rhe \lu~nt,ity of Mud uBed with thi.. alnount of l-elnell" anDy
vllry froan 3300 I for fine ..aud to 1) aut» g or InOl'. for uo. .......nd,
4. PROCEDURE
4.1 Qu'efuUy wipe the Row-table top clean and dry, and place the now
mould at the centre. Immediately after completing the mixing operation,
place a layer of mortar about 25 nun in thickness in the mould and tamp
20 times with the tamper. The tamping pressure shall be just sufficient to
insure uniform filling of the mould. Fill the mould with mortal" and tamp
clS specified for the first layer. Cut off the mortar to a plane surface, flush
with the top of the mould, by drawing the straight edge of a trowel (held
nearly perpendicular to the mould) with a sawing motion across the top of
the mould. Wipe the table top clean and dry, being especially careful to
remove any water front around the edge of the flow mould, Lift the mould
away from the mortar one minute aftel" completing the mixing operation.
Immediately, drop the table through a height of 12·5 rom ten times in 6
seconds. The flow is the resulting increase in average diameter of the
mortar mass, measured on at least four diameters at approximately equal
angles, expressed as a percentage of the original diameter, Should the flow
be too great, return the mortar to the mixing vessel, add additional sand,
and make another determination of the flow. If more than two trials need
be made to obtain a flow of 100 ±5, consider the mortar as a trial mortar,
and prepat"e test specimens Irom a new batch. If the mortar is too dry,
discard the batch. Determine the quantity of sand used by subtracting the
,,·eight of the portion remaining after mbdng from the weight of the initial
sample.
S. MOULDING TEST SPECIMENS
5.1 Immediately following completion of the tlow test, place the mortal- ill
7·06 em cube moulds in two layers, R.od each layer in place with
25 strokes of the tamping rod. After the redding has been completed. fill
the moulds to overflowing_ Place the specimens in a moist closet for curiDs.
Three to four houn after moulding. strike off the specimens to a amooth
lurface. 1lemove the apecimall from the moulds 20 to 24 bow.. after
moulcliDs UId ,tore in water until tested.
5
IS I 2386 ( Part VI ) • 1963
5.2 The temperature of the mixing water, moist closet, and storage tank
shall be maintained at 27 ± 2~C.
6. TESTING OF SPECIMENS
6.1 Test the specimens for compressive strength as given in 6.1.1 to 6.1.3.
6.1.1 Test the specimens immediately after their removal from the moist
closet in the case of 24-hour specimens, and from storage water in the case
of all other specimens, If more than one specimen at a time is removed
from the moist closet for the 24-hour tests, keep these specimens covered
with a damp cloth until time of testing. If more than one specimen at a
time is removed from the storage-water for testing, keep these specimens in
water at a temperature of 27 ± 2°C and of sufficient depth to immerse
completely each specimen until time of testing.
6.1.2 Surface-dry each specimen, and remove any loose sand grains or
incrustations from the faces that will be in contact with the bearing blocks
of the testing machine. Check these faces by applying a straight edge
(see Note). If there is appreciable curvature, grind the face or faces to
plane surfaces or discard the specimen 0
NOTE -- Results much lower than tho true strength will be obtained by loading
faces of the specimen that are not truly plane surfaces. Therefore, it. is essentia.l
that. specimen moulds be kept scrupulousty clean, us otherwise large irregularities
in the surfaces will occur. Instrurncuts for cleaning of moulds should 8h"8~'S be
softer than the Uleta) ill the moulds to prevent wear. In case grinding of specirneu
faces is necessary, it can be accoruplishod Lest by rubbing the specimen on a sheet
of fine emery papor or cloth glued to a plano surface, using only a. moderato
pressurc. Such grinding is tedious for more thau a few hundredths of a millimetre,
where more than this is found necessary, it is recommended that the specimen
be discarded.
6.1.3 Apply the load to specimen faces that were in contact with the true
plane surfaces of the mould. Carefully place the specimen in the testing
machine below the centre of the upper bearing block. Use no cushioning
or bedding materials. An initial loading up to one-half of the expected
maximum load for specimens having expected maximum loads of more than
2 500 kg may be applied at any convenient rate. Adjust the rate of load
application so that the remainder of the load ( or the entire load in the case
of expected maximum loads of less than 2 500 kg) is applied, without
interruption, to failure at such a rate that the maximum load will be
reached in not less than 20 nor more than 80 seconds. Make no adjust-
ment in the controls of the testing machine while a specimen is yielding
rapidly immediately before failure.
7. REPORTING OF RESULT
7.1 Report the average crushing strength of not less than three specimens
and also the age of test.
6

Headquarters:
ManakBhavan, 9 BahadurShahZafar Marg, New Delhi 110002
Telephones: 23230131,23233375,23239402 Fax: 91+011 23234062,23239399,23239382
E-mail: bis@vsnl.com website: http://www.bis.org.in
Central Laboratory: Telephone

Plot No. 20/9, Site IV, Sahibabad Industrial Area, SAHIBABD 201010 2770032
Regional Offices:
Central: ManakBhavan, 9 BahadurShahZatar Marg, New Delhi 110002 23237617
*Eastern; 1/14 CIT Scheme VII M, V.i.P. Road Kankurgachi, KOLKATA 700054 23378662
Northern: SeQ 335-336, Sector34-A, Chandigarh 160022 603843
Southern: C.I.T. Campus, IV Cross Road, CHENNAI 600113 254 ~9 84
Western: Manakalaya, E9, MIDC, Behind MarolTelephone Exchange, 28329295
Andheri (East), MUMBAI 400093
Branch offices:
'Pushpak' Nurmohamed Shaikh Marg, Khanpur, AHMEDABAD 380001 560 1348
Peenya Industrial Area, 1" Stage, Bangalore-TumkurRoad, BANGALORE 8394955
Commercial-cum-office Complex, opp. Dushera Maidan, Arera Colony, 2423452
Bittan Market,BHOPAL 462016
62/63, Ganga Nagar, Unit VI, BHUBANESHWAR 751001 2403139
tH
5 Floor, Kovai Towers, 44 Bala Sundaram Road, COIMBATORE 641018 221 0141
SCQ 21. Sector 12, Faridabad 121007 2292175
Savitri Complex, 116 G.T. Road Ghaziabad 201001 2861498
53/5 Ward No. 29, R.G. Baraua Road 5 by-lane, ApurbaSinha Path 2541137
GUWAHATI781003
5-8-56C L.N. Gupta Marg, Nampally StationRoad, HYBEAABAD 500001 23201084
E-52,Chitranjan Marg, C-Scheme, JAIPUR302001 2373879
117/418 B Sarvodaya Nagar, KANPUR 208005 2218774
Sethi Bhavan~ 2'Jd Floor, BehindLeela Cinema, Naval Kishora Road, 2215698
LUCKNOW 226001
NIT Building, SecondFloor,GokulpatMarket, NAGPUR 440010 2525171
MahavirBhavan, First Floor, Ropar Road, NALAGARH 174101 221451
Patliputra Industrial Estate, PATNA800013 2262808
First Floor, Plot Nos 657-660, MarketYard, Gultkdi, PUNE411037 4268659
"Sahajanand House" 3rd Floor, Bhaktinagar Circle,80 Feet Road, 2378251
RAJKOT 360002
T.C. No. 14/1421, University P.O. Palayam, THIRUVANANTHAPURAM 695034 2322104
1st Floor, UdyogBhavan, VUDA, Siripuram Junction, VISHAKHAPATNAM-03 2712833
SalesOffice is at 5 Chowringhee Approach, P.O. Princep Street, Kolkata700072 22371085

SalesOffice is at NoveltyChambers, Grant Road, MUMBAI 400007 23096528
Printed at PrahhatOffset Press,NewDelhi-2

Indian Standard: Methods of Test For Aggregates For Conci

Uploaded by

Copyright:

Available Formats

Indian Standard: Methods of Test For Aggregates For Conci

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Indian Standard: Methods of Test For Aggregates For Conci

Uploaded by

Copyright:

Available Formats

Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -

kolkata(anuradhapatra84@gmail.com) 42.110.148.147 [for non-commercial use only].

IS : 2386 ( Part VI) - 1963

IS J 1386 ( Part VI ) • 1963

Cement and Concrete Sectional Committee, BDC 2

BUREAU OF INDIAN STANDARDS

18 I 2386 ( Part VI ) • 1963

AMENDMENT NO. 1 FEBRUARY 1982

8.1 CaJ.culate the average crushing strength or Dot

2.1 The rine aggregate shllll be compared 1n !IOrter,

the at&Dd&r4 801utioD d••crlbe4 in 6.2.2 ot

Printed at Prabhat Offset Press, New Delhi-2

AMENDMENT NO.2 OcrOBER 1991

PART 6 MEASURING MORTAR MAKING PROPERTIES OF FINE

Printed at Prabhat Offset Press, New Delhi-2

IS I 2386 ( Part VI ) • 1963

18 I 2386 ( Part VI ) • 1963

Committee to derive assistance from C 87 - 62T Tentative Method of Test

III 1116 (Part VI) • 1963

IS I 2386 ( Part VI ) • 1963

BUREAU OF INDIAN STANDARDS

Central Laboratory: Telephone

SalesOffice is at 5 Chowringhee Approach, P.O. Princep Street, Kolkata700072 22371085

Printed at PrahhatOffset Press,NewDelhi-2

You might also like