Nistir4758 PDF

A 11 ID 3 7377T5
NISTIR #758
HVAC Functional Inspection and

Testing Guide
James Y. Kao
Building and Fire Research Laboratory

Gaithersburg, Maryland 20899
NIST
United States Department of Commerce
Technology Administration
-QC -V-_Lm al Institute of Standards and Technology
100
. U56
4758
1992
C.2
V
NISTIR 1758
HVAC Functional Inspection and

Testing Guide
James Y. Kao
Building Environment Division
Building & Fire Research Laboratory
March 1992
Prepared for:
U.S. Department of Commerce General Services Administration
Barbara Hackman Franklin, Secretary Richard G. Austin, Administrator
Technology Administration Public Building Service
Robert M. White, Under Secretary for Technology William C. Coleman, Commissioner
National Institute of Standards and Technology Office of Real Property Development
John W. Lyons, Director Washington, DC 20405
Abstract
ABSTRACT
This guide is developed for the Public Building Service (PBS) of the General
Services Administration (GSA) for final inspection and testing of heating,
ventilating, and air-conditioning (HVAC) systems in Federal buildings prior to
Government acceptance. The guide describes in detail the functional
inspection and testing procedures and calculations. It includes eight
chapters: General, Basic Measurement, Refrigeration Plant, Heating Plant, Air
Handling Equipment and systems, Building Automation Systems, Fire Safety Air
Moving Systems, and Unitary Air Conditioning Equipment. The appendix contains
detailed inspection checklist and test work sheets designed to be used in the
field.
iii
HVAC FUNCTIONAL INSPECTION AND TESTING GUIDE
Acknowledgment
This project is sponsored by the U.S. General Services Administration. The

author is grateful to Mr. David Eakin of GSA's Office of Real Property
Development for coordinating this effort; and to Mr. G.C. Rogerson, Chief,
Inspections Section and Mr. Michael Oliveri, both of GSA's National Capital
Region, for their constructive review of this Guide.
iv
Table of Contents
Table of Contents
CHAPTER 1 GENERAL 1
1. Scope 1
2. Purpose. . 1
3. Organization of This Guide 1
4. The Commissioning Team ..... 2
5. Designated Inspection and Testing Agent 2
6. Codes, Regulations, and Standards . . 3
7. General Principles 3
8 . Procedures and Sequences 4
9. Preparation and Coordination 5
10. Witness of Tests 5
11. Maintenance and Operation Manuals 5
12. Spare Parts . 5
13. Documentation 5
14. System Capacity 6
15. System Energy Consumption 6
16. Safety 6
17. Notation/ Abbreviation 7
CHAPTER 2 BASIC MEASUREMENT 9

1. Scope 9
2. General Requirements 9
3. Calibration of Test Instruments 9
4. Field Test Instruments 9
5. Permanently Installed Field Instruments 10
6. Standard Equations 10
7. Standard Test Procedures 10
EXHIBIT 2 -A FIELD TEST INSTRUMENTS 11

1. Selection of instruments 11
2. Field test instruments 11
3. Instrumentation instructions 16
EXHIBIT 2-B STANDARD EQUATIONS FOR CALCULATIONS 17
1. Air 17
2. Air property equations 17
3. Fan calculations 22
4. Flow rate measurement for water, air, steam, or
refrigerant 24
5. Electric power 26
v
EXHIBIT 2-C STANDARD TEST PROCEDURES 28

1. General 28
2. Reference standards 28
3. Permanently installed sensor locations 29
4. Simulation of sensors . 29
5. Measurement of air flow rate in duct 31
6. Measurement of air flow rate across coil or filter face . . 32
CHAPTER 3 REFRIGERATION PLANT . 33

1. Scope 33
2. Reference Standards. ......... 33
3. Refrigeration System Inspection 33
4. Refrigeration System Testing. ......... 34
EXHIBIT 3 -A INSPECTION PROCEDURES FOR REFRIGERATION

MACHINES . 35
1. General ....... 35
2. Centrifugal refrigeration machine . 37
3. Absorption refrigeration machine . .38
4. Reciprocating refrigeration machine ..... .38
5. Brush cleaning system for refrigeration machine 39
EXHIBIT 3-B INSPECTION PROCEDURES FOR HEAT REJECTION
EQUIPMENT 41
1. General ........ ...... 41
2. Cooling tower and evaporative condenser ... 42
EXHIBIT 3-C CENTRIFUGAL REFRIGERATION MACHINE TEST
PROCEDURES 44
1. Scope ..... ............ 44
2. Purpose 44
3. Industry standards 44
4. Preparation for test 45
5. Recommended tests 46
6. Instrumentation ......... . . 47
7. Test procedures 49
8 . Calculations and rate performance . 57
EXHIBIT 3-D RECIPROCATING REFRIGERATION MACHINE TEST
PROCEDURE . 59
1. Scope 59
2. Purpose 59
3. Industry standards . 59
5. Recommended tests . ...... 62
6. Instrumentation 63
8. Calculations and rate performance 74
vi
Table of Contents
EXHIBIT 3-E ABSORPTION REFRIGERATION MACHINE TEST

PROCEDURE 76
1. Scope 76
2. Purpose 76
5. Recommended tests . 78
6. Instrumentation . 79
EXHIBIT 3-F HEAT REJECTION EQUIPMENT TEST PROCEDURES . . 88
1. Scope and general 88
2. Purpose 88
7. Calculations and comparison of performance 95
CHAPTER 4 HEATING PLANT 99

1. Scope 99
2. Reference Standards 99
3. Heating System Inspection 100
4. Heating System Testing 100
EXHIBIT 4 -A INSPECTION PROCEDURES FOR BOILERS AND

FURNACES 101
1. Scope 101
3. General inspection 102
4. Boiler burner safety control inspection and tests.... 105
5. Boiler capacity control 108
6. Boiler safety relief valve inspection and test 108
7. Boiler water level, makeup water control and low water
cutoff 109
8. Other boiler inspection and tests 110
9. Air-heating furnace tests 112
EXHIBIT 4-B TEST PROCEDURES FOR BOILERS 113
1. Scope 113
3. General 113
4. Preparation for tests 115
6. Test Procedures 118
vii
EXHIBIT 4—C TEST PROCEDURES FOR AIR-HEATING FURNACES . 125

1. Scope 125
3. General 125
4. Preparation for tests 126
6. Test Procedures 128
CHAPTER 5 AIR HANDLING EQUIPMENT AND SYSTEMS . 137

1. Scope 137
2. Reference Standards ..... 137
3. Air Handling Equipment and System Inspection 138
4. Air Handling Equipment and System Testing 138
EXHIBIT 5-A INSPECTION PROCEDURES FOR AIR HANDLING

SYSTEMS 139
1. Scope 139
3. Air handling system general inspection 139
4. Fan 141
5. Heating and cooling coils 142
6. Air filters 142
7. Dampers 143
8. Air louvers 143
9. Casings . 143
10. Thermal insulation 144
11. Controls 144
12. Fan coil units and unit ventilators 146
EXHIBIT 5-B TEST PROCEDURES FOR AIR HANDLING SYSTEMS . 147
1. Scope 147
2. Industry standards ..... 147
3. General 149
5. Air handling unit component tests 153
6. Calculation and evaluation of performance of air handling
components 159
7. Air handling system operational tests . 162
CHAPTER 6 BUILDING AUTOMATION SYSTEMS ..... 171

1. Scope 171
2. Reference Standards 171
3. EMCS Inspection 171
4. EMCS Testing 172
viii
Table of Contents
EXHIBIT 6 -A INSPECTION PROCEDURES FOR BUILDING

AUTOMATION SYSTEM (BAS) 173
1. Scope 173
3. Inspection procedures 173
EXHIBIT 6-B TEST PROCEDURES FOR BUILDING AUTOMATION

SYSTEM (BAS) 177
1. Scope 177
3. General 178
CHAPTER 7 FIRE SAFETY AIR MOVING SYSTEMS 195

1. Scope 195
2. Reference Documents 195
3. Inspection of Fire Safety Aspects of Air Moving Systems .... 196
4. Testing of Fire Safety Aspects of Air Moving Systems 196
EXHIBIT 7 -A FIRE SAFETY INSPECTION PROCEDURES FOR AIR

MOVING SYSTEMS 197
1. Scope 197
3. General inspection procedures 199
4. Controls for systems without smoke control capability . . 203
5. Controls for systems with zoned smoke control
capability 203
EXHIBIT 7-B TEST PROCEDURES FOR ZONED SMOKE CONTROL
SYSTEMS 204
1. Scope 204
2. General references 204
3. Emergency power 204
4. Smoke control diagram 204
5. Normal operation test 204
6. Smoke mode test 205
EXHIBIT 7-C TEST PROCEDURES FOR STAIRWELL
PRESSURIZATION SYSTEMS 207
1 . Scope 207
2. General references 207
3. Emergency power 207
4. Normal operation test 207
5. Stairwell pressurization test 207
ix
CHAPTER 8 UNITARY AIR CONDITIONING EQUIPMENT ......... 209

1. Scope 209
3. Unitary air conditioning equipment inspection ......... 210
4. Unitary air conditioning equipment testing .......... 210
EXHIBIT 8 -A INSPECTION PROCEDURES FOR UNITARY AIR

CONDITIONING UNITS .... 211
1. Scope 211
3. Unitary air conditioning unit general inspection .... 212
4. Inspection items specific to rooftop units 215
5. Inspection items specific to computer room units .... 215
6. Inspection items specific to packaged terminal
air-conditioners 216
7. Fan 216
8. Heating and cooling coils . 217
9. Air filters ..... ...... 218
10. Dampers ......... 218
11. Air louvers 218
12. Casings 219
13. Thermal insulation 219
14. Controls . 219
EXHIBIT 8-B TEST PROCEDURES FOR UNITARY AIR
CONDITIONING UNITS 220
1. Scope 220
3. General 221
5. Rooftop and computer room unit tests 225
6. PTAC tests 233
7. Calculation and evaluation of performance 233
8. Air conditioning system operational tests . 236
APPENDIX (Inspection Check Lists and Test Work Sheets) ......... Al
x
CHAPTER 1 GENERAL
CHAPTER 1 GENERAL
1. Scope. This document addresses general criteria and procedures for the
functional inspection and testing of heating, ventilating, and air
conditioning (HVAC) equipment and systems prior to their acceptance.
Functional inspection and testing as used herein refers to those actions
necessary to verify system performance and operating conditions.
Commissioning process is defined by ASHRAE in ANSI/ASHRAE 1-1988 "Guideline
for Commissioning of HVAC Systems" as the overall process which includes
procedures and methods for documenting and verifying the performance of HVAC
systems so that the systems operate in conformity with the design intent. The
process starts at the pre-design phase and goes through the design phase, the
construction phase, the functional performance tests of installed equipment,
sub-systems and complete systems before acceptance, and ends with the post
acceptance phase. The functional inspection and testing as described in this
guide correspond to the functional performance tests phase of the ASHRAE
commissioning process. For brevity, this functional inspection and testing
will be referred to as commissioning in this document.
2. Purpose. Commissioning serves to improve project quality through the

validation of project design and the certification of product delivery. This
material is intended as a guide for evaluating and testing mechanical systems
before 3.1
being accepted and commissioned into building service. This document
is intended to serve as a reference source to GSA and contract personnel in
understanding procedural requirements associated with commissioning. Excerpts
and/or reference to specific commissioning material herein can be applied
within construction contract specifications as a means of defining project
requirements. References can also be made within Construction Management
contracts/actions to help define scope requirements.
3. Organization of This Guide.

This guide is organized in two parts.
3.1.1 The main body formulates basic inspection and test

requirements, organized into chapters which recognize major equipment
categories. Inspection and testing procedures for functional performance are
separately described by EXHIBITS within each chapter. The required data,
calculation equations, and acceptance criteria are given.
3.1.2 Recommended inspection check lists and test work sheets to

be used in the field, are grouped in the appendicx, cross referenced by number
to associated chapters.
Page 1
3.2 Often used equations for calculations are called Standard Equations
in this guide and are designated as SE- (number)
Often used test procedures are called Standard Test Procedures in

3.3
this guide and are designated as STP- (number)
Not all procedures identified apply to all equipment and systems of

3.4
a project. Project specifications and drawings should address required
inspections and tests for involved equipment and systems. The inspection
lists and test work sheets in the appendicx are designed for field use and
should be duplicated to suit the individual project.
4. The Commissioning Team.

The commissioning team (often abbreviated "the Team" in this guide)
4.1
is the team which represents Public Building Service (PBS) in the
commissioning process. The commissioning team could be composed of PBS
construction engineer(s), agency operation and maintenance representatives,
construction (quality) manager, the contract architect/engineer, and/or
specialty consultants. Depending on the sophistication of the equipment and
systems, the Team may also include designers, fire/safety officers, equipment
and system specialists, and/or supplemental inspection contract agents.
4.2 The commissioning team must be able to understand and to interpret

contract specifications and drawings. However, the team has no authority to
alter the requirements of these documents.
Testing and operation of equipment and systems during commissioning

4.3
is the responsibility of the construction contractor or his representatives
(see paragraph 5. below). The Team shall inspect and verify that equipment
and systems are installed in accordance with the contract documents and
witness all tests conducted by the contractor and perform verifications and
documentation
4.4 The project contract should require the contractor to assist the
commissioning team in inspections when needed (e.g. access to inside boilers).
4.5 The PBS construction engineers will coordinate the commissioning

process. Final responsibility for acceptance of the HVAC system shall be as
designated by the Contracting Officer.
5. Designated Inspection and Testing Agent.
5.1 Designated testing agents are the persons actually operating the
equipment/systems and performing tests during commissioning. Contractually,
Page 2
. . . . . . .
CHAPTER 1 GENERAL
5.2 almost always be the installing contractor and/or manufacturer of

this will
the installed equipment/system.
Designated testing agents may be employees of the equipment

manufacturers, independent testing laboratories or agencies, and other
qualified specialists. Project specifications usually specifies the
qualifications of testing inspection agents. For major equipment testing,
such as for large chillers and boilers, it may be appropriate to require
factory personnel of the equipment manufacturer as the testing agent.
6. Codes, Regulations, and Standards. Where codes, regulations, and

standards are cited in this guide and its appendices, the latest editions
shall be used unless construction contract specifications direct the specific
use of an earlier version. Relevant standards of the following organizations
are listed in the equipment chapters as general references for interested
readers
a. American Society of Heating, Refrigerating, and Air-Conditioning

Engineers (ASHRAE)
b. American Society of Mechanical Engineers (ASME)
c. Air-Conditioning and Refrigeration Institute (ARI).
d. National Fire Protection Association (NFPA)
e. Underwriters Laboratories (UL)
f . Sheet Metal Contractors National Association (SMACNA)
7. General Principles. Inspect and test HVAC equipment and systems to

verify that construction, installation, and performance is in accordance with
the project specifications, drawings, approved submittal documents, and
generally recognized good practices.
7.1 All components and systems must meet project specifications

drawings and contract requirements
7.2 Since product data, shop drawings, and wiring diagrams of major
equipment are typically required by construction contract documents to be
submitted for approval before installation, the following should be done.
7.2.1 For the equipment and systems whose submittals are

approved, verify that the installation meets contract requirements.
7.2.2 For the equipment and systems whose submittals are approved
Page 3
as noted, pay special attention to the items noted as conditions of approval.
7.2.3 In no case should rejected equipment and systems be

installed.
7.2.4 For equipment and systems where submittals are not

required, verify the quality and quantity as specified.
7.2.5 Verify the performance of equipment and systems to meet

specification requirements.
7.3 The inspection and functional testing procedures outlined in this

guide assumes that project construction is virtually complete, including
balancing and adjusting of all equipment and support systems.
7.4 Any equipment which has been used extensively before commissioning
inspection and testing must be cleaned or reconditioned to meet the project
specification requirements.
7.5 Temporary measures (such as temporary piping hookups) may be

required for inspection and testing. Unless otherwise directed in design
documents, temporary measures shall be removed and the systems restored to
their specification required permanent conditions after inspection and testing
are performed.
7.6 The specification of each project must specify the scope of

functional tests required for the project. Selected inspection and test
procedures from this guide must be incorporated into the project
specification. As this guide gives general principals for project inspection
and testing, special project equipment/system may require different
commissioning procedures. The commissioning team must give individual
planning to each project before field inspection and testing.
8. Procedures and Sequences.

8.1 Inspection. Inspection is the first step in commissioning any
equipment and system. Observe and note damage, rust, omissions, and unsafe
conditions. For equipment and systems which have been required to submit shop
drawings for approval, it is necessary to verify that products and
installation are in accordance with the design and approved submittals.
8.2 Steady-state tests. Steady-state tests are usually used to verify

the design capacities and conditions of the equipment and systems. These
tests should generally be performed after inspection procedures are completed.
The exact kind of tests to be performed depend on what the contract documents
require. If steady-state tests do not meet project requirements, operation
tests (see paragraph 8.3 below) should not be performed.
Page 4
. .
CHAPTER 1 GENERAL
8.3 Operation tests. These tests should be performed after the

steady-state tests are performed. All designated modes of operation shall be
witnessed to verify proper sequencing, control stability, and assurance of
system performance. These tests can usually be used to predict future
operation deficiencies.
8.4 Factory tests. Where specifications require factory testing of

either the installed item or a similar item, copies of test reports must be
provided to the commissioning team.
8.5 Inspections and tests may be performed concurrently, if time and

costs may be saved.
9. Preparation and Coordination.

9.1 The commissioning team must become familiar with contract
documents, design intent, project specification, drawings, manufacturer's
installation instructions, and manufacturer's operation and maintenance
manuals
9.4
9.2 The commissioning team shall coordinate with the project manager
and/or construction engineer to review inspection records and to obtain
pertinent information regarding the history of construction.
9.3 The commissioning team shall plan, prepare and review the test
procedures for the equipment and systems to be tested and coordinate the
tests
If a Quality Control Plan is required of the contractor, consult

scheduling and other requirements for involved inspections and tests.
10. Witness of Tests. The commissioning team must witness all tests.
11. Maintenance and Operation Manuals. Before commissioning

inspection, be certain that maintenance and operating manuals have been
delivered to the Government in accordance with contract requirements.
12. Spare Parts. During the inspection, verify the quality and quantity
of spare parts as may be required by project specifications.
13. Documentation.
13.1 The testing inspection agent and the commissioning team shall
Page 5
record and maintain detailed inspection and testing data. The data recorded
shall be comprehensive, concise, and precise.
13.2 All data must be recorded as soon as possible during the course of
the inspection and testing.
13.3 All documentation shall have the date, time, and names of persons
participating in the inspection and testing.
13.4 All test instruments shall be documented for valid calibration.
13.5 The recommended data recording work sheets and inspection check
lists are shown in the appendices cross referenced to the various chapters of
this guide where inspection and testing procedures/criteria are detailed.
13.6 The commissioning team should be aware that inspection and testing
records may be used as evidence in legal disputes.
13.7 PBS construction engineers of the commissioning team will receive

the final documentation for the Government.
14. System Capacity.
14.1 The capacities of HVAC systems and components at full load shall
be not less than those indicated in contract documents, project specifications
and drawings
14.2 At full load conditions, the space temperature shall not differ
from design set temperature +/- set point control tolerances.
15. System Energy Consumption. The installed HVAC system must operate
efficiently. The energy consumption rates shall not be greater than the full
and part load energy rates as indicated in the contract documents, project
specifications and drawings.
16. Safety.
16.1 All equipment and systems must be able to operate safely for the
system operating personnel, building occupants, and the public.
Necessary precautions must be taken during inspection and testing

16.2
to prevent injury to personnel and damage to equipment. These shall include,
but not limited to:
Page 6
CHAPTER 1 GENERAL
16.2.1 Providing fire extinguishing equipment.
16.2.2 Presence of all factory recommended guards to belt drives,

rotating shafts, and electrical leads.
16.2.3 No clutter of construction debris.
16.2.4 No ongoing work by other trades in immediate areas.
16.2.5 Lock-out capability to all secured electrical circuits.
16.2.6 Personnel safety gear, including acoustic ear protection,

safety glass and hard hats.
16.2.7 Make no overrides to equipment safety controls, except as

required to test secondary safety control/operation.
16.2.8 Coordinate all temporary control modifications and

equipment tests with the Building Manager and Construction Engineer.
17. Notation/Abbreviation . Abbreviations for organizations contained

in this guide are listed in the following table:
AABC Associated Air Balance Council

ACC A Air-Conditioning Contractors of America
ADA Air Diffusion Council
AGA American Gas Association
AHAM Association of Home Appliance Manufacturers
AMCA Air Movement and Control Association
ANSI American National Standards Institute
ARI Air-Conditioning and Refrigeration Institute
ASHRAE American Society of Heating, Refrigerating and Air-Conditioning
Engineers
ASME The American Society of Mechanical Engineers
ASTM American Society for Testing and Materials
CTI Cooling Tower Institute
HYD I Hydronics Institute
IEEE Institute of Electrical and Electronic Engineers
ISA Instrument Society of America
NEBB National Environmental Balancing Bureau
NEMA National Electrical Manufacturers Association
NFPA National Fire Protection Association
SMACNA Sheet Metal and Air Conditioning Contractors National
Association
UL Underwriters Laboratories, Inc.
Page 7
Page 8
: . . .
CHAPTER 2 BASIC MEASUREMENT
1. Scope. This chapter provides general instrumentation requirements and

basic measurement techniques for commissioning tests.
2. General Requirements. Instrumentation selection and measurement

techniques shall generally comply with recommendations of the following
organizations
a. American Society of Heating, Refrigerating, and Air-Conditioning

Engineers (ASHRAE)
b. American Society of Mechanical Engineers (ASME)
c. Instrument Society of America (ISA).
d. American Society of Testing and Materials (ASTM)
3. Calibration of Test Instruments.
3.1 All test instruments must have valid calibration.
3.2 Calibration of test instruments may be performed by their

manufacturers with calibration certificates, by companies or government
agencies regularly engaged in calibrating similar instruments, or as witnessed
during testing in accordance with calibrating procedures recommended by the
instrument manufacturer or organizations listed in paragraph 2. above.
4. Field Test Instruments.

4.1 The minimum accuracy requirements for equipment testing are listed
under the equipment testing chapters of this guide. Field test instruments
must meet these minimum requirements.
4.2 The expected accuracies of the most commonly used field test
instruments and some precautions for their use are listed in EXHIBIT 2-A.
4.3 The 1989 ASHRAE Handbook of Fundamentals, Chapter 13 also lists the
commonly used test instruments and their associated ranges and accuracies.
Page 9
.

5.
Permanently Installed Field Instruments.

5.1 Permanently installed instruments may be available as part of the
basic construction contract requirements. If identified for the purpose of
commissioning, these sensors, transmitters, and wiring, must be calibrated and
inspected to insure that they will perform properly. It is extremely
important that special attention be paid to their installation locations and
details during the inspection. Strict adherence to the recommendations of the
manufacturers or those of the organizations of paragraph 2. above must be
6.
observed .
5.2 Specific recommendations of installation and testing of these

instruments may be found in the Appendices.
7. 5.3 Permanently installed field instruments may be used for

commissioning tests, if they are proven to meet accuracy requirements.
Standard Equations.
6.1 Standard equations shall be used as referenced herein for

calculations which evaluate equipment and system performance.
6.2 Standard equations are listed in EXHIBIT 2-B.
Standard Test Procedures.

7.1 During equipment and system tests, standard test procedures shall
be adhered to as much as possible.
7.2 Standard test procedures are listed in EXHIBIT 2-C as well as other
chapters of this guide where equipment and system test procedures are
described
7.3 Discussion of error analysis may be found in ASHRAE 1989

Fundamentals Handbook, Chapter 13, ANSI/ASHRAE Standard 114 (Practices for
Measurement, Testing, Adjusting, and Balancing of Building Heating,
Ventilating, Air Conditioning and Refrigeration Systems).
Page 10
. . . 4
2
3
EXHIBIT 2 -A FIELD TEST INSTRUMENTS
1. Selection of instruments.
1.1 A general principal of selecting instruments is to match the
minimum instrument accuracies to the allowed measurement tolerances. The
required measurement tolerances are specified in contract documents or given
in testing procedures of this guide.
1.2 In order to minimize the instrumentation error, the ranges of the

instruments should be selected close to the intended measurement without
chances of overloading the instruments. Many instrument accuracies are
expressed in percent of full scale readings which will result in very large
when the measured quantities are not close to the full scale readings.
errors 2.1
In such cases, instrument of different ranges should be used.
2. Field test instruments. The following instruments can easily be

carried and used in the field. Listed are the accuracies of these instruments
and precautions of their use. These accuracies are considered to be easily
attainable
Temperature.
2.1.1 Portable digital thermometer. Use to measure air or water

temperature. Accuracy +/- 0.3 °C (0.5 °F) .
2. 1.1.1 Use contact grease for thermometer well

applications
2. 1.1. 2 Do not take measurements in stagnant areas.
2.1.2 Mercury- in- glass thermometer. Available in various grades

and graduations. Select thermometer to suit required accuracy. Thermometers
graduated in 0.1 °C (0.2 °F) is easily obtainable for temperature from 0 to
149 °C (32 to 300 °F)
2. 1.2.1 May be used for high accuracy applications and for

calibrating other temperature instruments. Relatively long response time.
2. 1.2. Careful reading of scale is required. Use

magnifying glass, if necessary.
2. 1.2. If partial- immersion thermometer is used, align the

immersion line with the fluid being measured.
2. 1.2. Adjustment for immersion may be necessary for high

accuracy applications.
Page 11
6
5 , ,
* Using total- immersion thermometer partially immersed:
correction = 0.00016 n (t x -t) (For SI)

,
= 0.00009 n (tj^-t), (For Customary)
where n = mercury column length outside measuring

fluid, expressed in temperature
t : = indicated temperature, °C (°F)
t = average stem temperature, measured with an
auxiliary thermometer, °C (°F)
* Using partial- immersion thermometer in an environment

where the stem temperature differs substantially from the stem temperature
marked on the thermometer:
correction = 0.00016 n (t x -t) (For SI)

or 0.00009 n (t x -t) (For Customary)
where n = mercury length above immersion line,

expressed in temperature
t : *= stem temperature marked on thermometer,
°C (°F)
t = average stem temperature, measured with an
auxiliary thermometer, °C (°F)
2. 1.2. See paragraph 2.1.1 above for use precautions.
2. 1.2. If mercury column separation has taken place, the

gaps must be eliminated by carefully heating or cooling the mercury bulb until
the gaps reach the upper or lower chamber (consult thermometer manufacturer or
thermometer care book for details) The thermometer must be recalibrated.
.
2.1.3 Electric resistance box. Use to simulate electric

resistance for calibrating resistance temperature detector (RTD) in critical
applications, such as for differential temperature measurement in chilled
water lines). Accuracy 0.1 ohm. Contact terminals must be polished after
extended period of storage to minimize measurement errors.
2.2.4 Thermocouple indicator/simulator. Use for indicating

temperature from thermocouple input or simulating thermocouple output.
Accuracy of +/- 0.5 °C (0.9 °F) may be achieved with factory calibrated
thermocouple wires.
2.1.5 Infrared thermometer. Use for testing steam leaking.

Accuracy +/- 2% full scale.
Page 12
.

2.2
Humidity.
2.2.1
Sling and aspirated psychrometer Accuracy +/- 3% RH.

. (The
accuracy of sling psychrometer is limited by the thermometer length and
°
graduation. Accuracy of +/- c (1 ° F ) wet bulb, equivalent to
approximately 3.5% RH at 25 °C (77 °F) and 50%RH, can be expected.)
2. 2. 1.1 Wicks must be clean and only distilled water is

used for the wet-bulb thermometer. Be sure the wicks are fully wet during
measurement
2. 2. 1.2 The air velocity should be at 3 - 5 m/s (590 - 984
ft/min) across the wet bulb. For the sling type, swing the psychrometer to
produce the recommended 1.1speed.
2. 2. 1.2
1.3 Thermometers need calibration.
2.2.1
2. 2. 1.4 Sling psychrometer is simple in construction and
easy to use. It should be considered as an essential instrument in all
commissioning work.
Portable digital humidity meter. Accuracy +/- 3% RH.
2. 2. Avoid high humidity environment of over 95% RH or

low humidity 2.3.1
environment of under 20% RH.
2. 2. Must be recalibrated frequently.
2.3 Pressure.
3.1
U-tube manometer. Accuracy +/- 7 Pa (0.03 in. of water).
2. 3. 1.1 Must use the right density fluid.
2. 3. 1.2 Leveling of manometer is important.
2. 3. 1.3 Be careful reading scales (avoid parallax errors).
2. 3. 1.4 When using a static pressure tip for measuring air,

the location of the sensing tip must be selected that no velocity component of
the air flow affects the readings.
2.3.2 Inclined manometer. Accuracy +/- 2.5 Pa (0.01 in. of

water). Same application precautions as described for U-tube manometer.
2.3.3 Bourdon- tube and bellow type pressure and compound gage.
Accuracy +/- 0.1% full scale.
2. 3. Must be calibrated periodically.
Page 13
2
3
2 . 3 . 3 . Be aware of possible errors caused by parallax,
2 . 3 . 3 . 3 Must not subject to overpressure.
2. 3. 3.4 Be aware of possible error caused by elevation of

gage.
2.3.4 Diaphragm air pressure gage. Accuracy +/- 2% full scale.

Same application precautions as paragraph c. above.
2.3.5 Pressure calibrator.
2. 3. 5.1 For simulating pneumatic control systems - range to

3
357 kg/m (20 psig) . Accuracy +/- 0.5% full scale.
2. 3. 5. For simulating duct air pressure - range depends on

application.
2. 3. 5. Commonly used "squeeze bulb" is not a good

instrument for creating and maintaining a desired pressure and should not be
used for commissioning work.
2.3.6 Pressure readings for air or water are often fluctuating.

Applying pressure restriction devices between the test instruments and the
tested equipment usually helps. If the instrument readings still fluctuate,
the average of several readings must be used.
2.4 Velocity and flow rate.
2.4.1 Pitot tube.
2.4. 1.1 In combination with appropriate pressure measuring

instrument to measure air velocity. For example, inclined manometers with
accuracy of 1.2 Pa (0.005 in. of water) may be used to measure air velocity
down to 3 m/s (590 ft/min) to give results within 15% accuracy.
2. 4. 1.2 Selection of traverse location is important. Avoid

locations having unstable air flow profiles. A minimum distance of 7.5
diameters down stream of duct fittings or 1.5 diameters after straightening
vanes is preferred.
2. 4. 1.3 In calculating the average velocity cf air in a

duct, average the individual velocities of the traverse, not the velocity
heads (pitot readings).
2.4.2 Air measurement station. A permanently placed in-duct unit

consisting of numerous pitot tube sensors manifolded together with pressure
gages or other readout devices to give readings of velocity pressure,
Page 14
2
velocity, or air flow rate. Units equipped with air straighteners upstream of
pressure sensing tips are available.
2. 4. 2.1 Data of accuracy and air friction for these units

may be obtained from manufacturer. +/- 5% reading is usually obtainable.
2. 4. 2. Site conditions are critical for good measurement.

Unit manufacturers usually make recommendations for location selections.
Units with air straighteners are required should duct placement not match
2 . 4 . 1 . 2 .
2.4.3 Heated thermocouple anemometer. May measure down to 0.05

m/s (10 ft/min) air velocity. Accuracy +/- 3% of reading or no less than +/-
0.01 m/s (2 ft/min). Correction for air temperature and humidity may be
necessary. Consult manufacturer's instructions.
2.4.4 Rotating vane anemometer.
2. 4. 4.1 May be used to measure air velocities lower than

for pitot tube at locations such as coil face or grille face. Accuracy is +/-
10% of reading and is considerably lower than that of pitot tube at ideal
locations and velocities.
2. 4. 4. Instrument must be calibrated for the entire range

of the intended velocity.
2.4.6
2.4.5 Flow hoods are used to measure volume flow of air from
devices such as air diffusers and registers. Accuracy depends on the velocity
reading instrument used. The hood and reading instrument must be calibrated
as a unit.
Positive displacement meters measure volumetric flow rate

of gas and liquid. Accuracy +/- 1% full scale.
2.5 Electric power, energy, voltage, and current.
2.5.1 Portable kilowatt meter/kilowatt-hour meter. Accuracy +/-

1% of reading at unity power factor.
2.6.1
2.5.2 Electric clamp-on meter (for motor current and voltage
measurement). Accuracy +/- 2% full scale.
2.5.3 Some instruments may require zeroing before measurement.

Frequent calibration may be needed.
2.6 Rotation speed.
Contact tachometer. Accuracy +/- 1 rpm. Exercise caution

in taking readings. Guards for drive mechanisms should have provisions to
Page 15
remain in place while making measurements.
2.6.2 Photo tachometer. Accuracy +/- 1.5% full scale.
2.6.3 Stroboscope. Accuracy +/- 3% full scale.
2.7 Portable temperature/humidity recorder. For recording space

temperature and humidity over a minimum period of one week. Accuracy depends
on the quality of the instrument and the resolution of the scale. Generally,
+/- 2% and 4% of full scale may be achieved for temperature and humidity
measurements, respectively. Should be calibrated periodically.
2.8 Portable refrigerated liquid bath. For calibrating temperature

instruments. Must provide +/- 0.01 °C (0.02 °F) temperature stability.
Minimum temperature range -20 - 100 °C (-4 - 212 °F) .
2.9 Refrigerant leak detector. Automatic electronic halogen leak

detector for continuous refrigeration system leak detection. Sensitivity
3ppm.
2.10 Orsat flue gas analyzer. For measuring and analyzing flue gas.
Measures oxygen, carbon dioxide, and carbon monoxide components in the
combustion product.
2.11 Flow measurement of liquid and superheated steam may be performed

using pressure instruments connected to pressure taps of built-in flow
measuring device such as orifice plate, flow nozzles, and venturies. See
pressure section for accuracy for manometers, pressure gages, etc.
3. Instrumentation instructions. Whenever the instructions or user

manuals are available from the instrument manufacturers, they should be
closely followed.
Page 16
: .
EXHIBIT 2-B STANDARD EQUATIONS FOR CALCULATIONS
1. Standard air is defined as air having a density of 1.20 kg/m 3

Air.
(0.075 lb/ft 3 ). This density is approximately that of dry air at a barometric
pressure of 101.039 kPa (29.92 in. of mercury) and a temperature of 21 °C (70
°F) Most construction documents and manufacturer's equipment data express
.
air properties in terms of standard air. When air flow rate measurement is
performed at conditions considerably different from these conditions, it may
be necessary to adjust to standard conditions in order to compare the measured
results with specified quantities.
If the temperature of air is higher than 29 °C (85 °F) or lower than 13 °C (55
°F) the measured volume flow rate should be adjusted to that of the standard
,
air by using SE-7 and SE-14 (see example 2). Without adjusting between these
temperatures, the maximum error is 3%.
The effect of static pressure inside an air duct or air handling apparatus can
usually be ignored in air calculations (e.g. the error of air density for
ignoring a 995 Pa (4 in. of water) static pressure under 101.039 kPa (29.92
in. of mercury) barometric pressure is less than 1%). Barometric pressure
changes have far more influence on air properties and should be used in all
pertinent calculations. The commissioning team should note under what
conditions the air quantities are specified in the construction documents (at
standard conditions or at high elevation conditions) The air equations given
.
in this EXHIBIT may be used directly if the barometric pressure is measured

during the commissioning. If barometric pressure is not measured, an estimate
of total air pressure may be made by using the following standard atmospheric
data
Altitude, m (ft) Pressure, kPa (in. Hg)
152 (500) 99.21 (29.38)

305 (1000) 97.46 (28.86)
610 (2000) 93.94 (27.82)
914 (3000) 90.57 (26.82)
1219 (4000) 87.19 (25.82)
1524 (5000) 84.08 (24.90)
1829 (6000) 80.98 (23.98)
2134 (7000) 77.97 (23.09)
For sample air property calculations at high altitude, see Example 1 below.
2. Air property equations. The following air property equations are

presented for reference for possible use during commissioning. The theory and
derivation of these equations may be found in most engineering handbooks of
thermodynamics, and fluid mechanics, for example, the ASHRAE 1989 Handbook of
Fundamentals
Page 17
.
2.1
Saturated water vapor pressure. Knowing the dry-bulb temperature

of the air, the saturated water vapor pressure may be found from steam tables
(e.g. 1989 ASHRAE Fundamentals Handbook, Chapter 6, Table 2) or using the
following equation. The equation yields less than 1% error if the dry-bulb
temperature is above -1 °C (30 °F)
636 ' 728A/(1 8 x Td +

P sw = 3376.85 x e (15 * - * 2 «>>
(For SI) SE-I
728A/(Td + 392))
P sw = e (15 A636
"
(For Customary)
where constant e = exp 1 = 2.71828
2.2 Vapor pressure. Knowing the relative humidity of air (by direct
measurement) and saturated vapor pressure (SE-1), the vapor pressure of air
may be calculated.
Pw *= RH x P sw SE-2
2.3 Humidity ratio. Humidity ratio of air may be calculated by knowing

the barometric pressure (by direct measurement) and air vapor pressure (SE-2).
W = 0.622 x Pw / (Pb - PJ SE-3
2.4 Enthalpy of air. Enthalpy of air is calculated from air humidity

ratio (SE-3) and dry-bulb temperature.
H = T d + W (2501 + 1.805 x T d ) (For SI) SE-4
H = 0.24 x T d + W (1061 + 0.444 x T d) (For Customary)
2.5 Specific volume of air. To calculate specific volume of moist air

knowing barometric pressure, dry bulb temperature, and humidity ratio.
287.055 (273.15 + T d )
v - (1 + 1.6078 x W) (For SI) SE-5
Pb
0.7543 (459.67 + T d )
v = - (1 + 1.6078 x W) (For Customary)
Pb
2.6 Density of moist air.
D *= (1 + W) / v SE-6
Page 18
2.7
Adjusting density of air. Air density may be adjusted from one set
of temperature and pressure to another set.
Di Pi + Pb i T d2 + 273.15
---- - ( ) ( ) (For SI) SE-7
D2 P 2 + Pb2 Tdi + 273.15
Di Pi + 13.6 P bl T d2 + 459..67
= ( ) ( ---) (For Customary)
d2 P 2 + 13.6 P b2 T dl + 459..67
2.8 Air velocity by pitot-static and reverse pitot measurement.

Velocity pressure is directly obtained by measuring of total pressure and
static pressure with a pitot tube.
Pv - P t - SE-8
Velocity of air stream may be calculated from velocity pressure.
V - 139.91 (P v / D) 1/2 (For SI) SE-9
V - 1096.5 (Pv / D) 1/2 (For Customary)
At 101.325 kPa (29.921 in. Hg) atmospheric pressure and 21.1 °C (70
°F) air temperature, the air density is 1.20 kg/m 3 (0.075 lb/ft 3 ). The
equation reduces to:
V -= 127.63 (P v ) 1/2 (For SI) SE-10
V = 4004 (P v ) 1/2 (For Customary)
The average velocity of several velocity-pressure readings is

calculated by (at standard air conditions):
1/2
sum [(P v ) ]
V = 127.63 (For SI) SE-11

no. of readings
sum [(P v ) 1/2 ]
V = 4004 (For Customary)

no. of readings
2.9 Volume flow rate.
Q = A x V SE-12
2.10 Relationship of volume flow rate, velocity, and density.
Qi / Q 2 = V x / V 2 = D 2 / Di SE-13
Page 19
2.11 Mass flow rate.
M = QxD = Q/ v SE-14
2.12 Duct system air friction. The following equation may be used in
most applications to plot duct system curves or to calculate new air friction
from known air flow rates and air friction.
2
(Qi / Q2 ) “ (Fi / F 2 ) SE-15
2.13 Conversion from gage to absolute pressure.
P a = Pb + P 6 SE-16
Symbols for air: A = net cross sectional area of duct, m 2 (ft 2 )

D = density of air, kg/m 3 (lb/ft 3 )
F = air friction (or pressure drop), m (in.) of water
H *= enthalpy of air, kJ/kg of air (Btu/lb of air)
M *= air mass flow rate, kg/s (lb/min)
P - static pressure of air, kPa (in. of water)
P a - absolute pressure
P b = barometric pressure, kPa (in. of Hg)
P g = gage pressure
P s = static pressure, m (in.) of water
P sw = saturated vapor pressure, Pa (in. of Hg)
P t *= total pressure, m (in.) of water
P v = velocity pressure, m (in.) of water
P w = vapor pressure of air, Pa (in. of Hg)
Q = volume flow rate, m /s (ft /min)
3 3
RH = relative humidity of air, %

T d = dry-bulb temperature of air, °C (°F)
v = specific volume of moist air, m 3 /kg of dry air (ft 3 /lb
of dry air)
V = air velocity, m/s (ft/min)
W = humidity ratio, kg (lb) of vapor/kg (lb) of dry air
1 ,
2 = at 1 or 2 conditions
Example 1 - air property calculations:
Assume that the following air properties are measured: T d = 26.7 °C

(80 °F) RH = 61%, and P b = 84.09 kPa (24.90 in. of Hg) (at approximately 1524
,
m (5000 ft) above sea level).
Saturated vapor pressure (SE-1):
(15A63 6-7284/(l. 8x26. 7+424) = 3,493 k p a For

P sw = 3376. 85xe ( S I)
Page 20
t : :
4636-7284/(80+392) _ 1.032 in. Hg

P sw - e ( 15 (For Customary)
.
)
Vapor pressure (SE-2)
P w = 0.61 x 3491 = 2.130 kPa (For SI)
Pw *= 0.61 x 1.032 = 0.6296 in. Hg (For Customary)
Humidity ratio (SE-3):
0.6296
W - 0.622 ( )
= 0.01614 kg (lb) of moisture/kg (lb)
24.90 - 0.6296 of dry air
Enthalpy of air (SE-4)
H - 26.7 + 0.01614 (2501 + 1.805 x 26.7) - 67.84 kJ/kg
H - 0.24 x 80 + 0.01614 (1061 + 0.444 x 80) -= 36.90 Btu/lb dry air
Specific volume of air (SE-5)
287.055 (273.15 + 26.7)

v (1 + 1.6078 x 0.01614)
84090
= 1.050 m 3 /kg dry air
0.754 (460 +80)

v (1 + 1.6078 x 0.01614)
24.90
= 16.78 f 3 /lb dry air
Density of air (SE-6):
1 + 0.01614
D 0.9678 kg/m 3
1.050
1 + 0.01614
D - - 0.06056 lb/ft 3
16.78
Example 2 - adjustment of measured air flow rates:
Air flow rate is measured in a duct with pitot tube and a pressure
measuring device to be 4.248 m 3 /s (9000 ft 3 /min) The temperature . of air at
the place of flow measurement is 48.9 °C (120 °F) The barometric . pressure is
at standard atmospheric pressure 101.325 kPa (29.92 in. Hg) The . volume flow
Page 21
)
rate at standard air conditions is (SE*7 and SE-13):
273.15 + 21.1
Q - 4.248 x 3.881 m 3 /s
273.15 + 48.9
460 + 70
Q *= 9000 x 8224 ft 3 /min
3.1
460 + 120
3. 3.1.1
Fan calculations.
Definition of fan pressure.
3.1.2 The basic pressure equation in any duct is SE-8, i.e.,
Pt = Ps + Pv
where Pt, Ps ,
and Pv can all be measured.
Fan pressure by definition:
Fan total pressure:

tf t(out) -
Ptu
(in) SE-17
Fan velocity pressure:

Pvf = Pv(out) SE-18
Fan static pressure:
3.1.3 Psf — Ptf * Pvf SE-19

— Pt(out) “ Pt(in) Pv(out
_ Ps(out) Pv(out) Pt(in) P v(out)
P.f — Ps(out) ”
Pt(in) SE-20
Note that fan static pressure is not the difference

between the static pressures at fan outlet and inlet.
Special cases:
3. 1.3.1 Fan with inlet duct only.
Ps(out) “ 0
Psf = *
Pt(in) 21
Note that it is always negative.
Page 22
3
2 )
Ptf - Pt(out) P t(in)

Pv(out) Pt(in) SE-22
3. 1.3. Fan without a inlet duct.
Ps in)(
= Pv(in) “ Pt(in) - ®
Ptf = Pt(out) Pt(in)

— Pt(out) SE-23
P.f “ Ptf ‘ Pvf = Pt(out) *

Pv(out)
Ps (out SE-24
3. 1.3. Fan with both inlet and outlet ducts.
Ptf = Pt(out) Pt(in) SE-25
Psf - Ps(out) P t(in) same as SE-20
Symbols: all units in Pa (in. of water)

P t(out) = outlet total pressure
P s(out) = outlet static pressure
Pv(out) = outlet velocity pressure
Pt(i n = inlet total pressure
)
P s in) = inlet static pressure

(
P V (in) = inlet velocity pressure

P tf = fan total pressure
P sf = fan static pressure
P vf = fan velocity pressure
3.2 Fan equations.
3.2.1 For the same fan and air density:
Qi = q 2 X (N, / N 2 ) SE--26
Ptl or ]
?sl = (P t2 or P s2 ) x (N x / n 2 ) 2 SE--27
Wi = W 2 X (N x / N 2 ) 3 SE-•28
Ptl or P sl - (P t2 or P s2 ) x (Qi / q 2 ) 2 SE-29
Wi " SE-30
3
W2 X (Qi / Q 2 )
Pti or P sl
(3/2)
Wi = W 2 X ( ) SE-31
Pt 2 or P s2
Page 23
:
BVAC FUNCTIONAL INSPECTION AND TESTING GUIDE
3.2.2 For the same fan and speed, at varying air density:
Pti or P.i Di
SE-32
P t2 or P s2 D2
Wi / W2 - D x / D 2 SE-33
3.2.3 Fan efficiency:
(e) t = Pt x Q / W (For SI) SE-34
(e) t - P t x Q / 6350 W (For Customary)
(e) 8 = Ps x Q / W (For SI) SE-35
(e) s = P s x Q / 6350 W (For Customary)
Symbols
D = air density, kg/m 3 (lb/ft 3 )
(e) s - fan static efficiency, %
(e) t = fan total efficiency, %
N = fan speed, RPM
P s - static pressure, Pa (in. of water)
P t = total pressure, Pa (in. of water)
Q = volume flow rate, m /s (ft /min)
3 3
W = power input, W (hp)

1, 2 = at 1 or 2 conditions
4. Flow rate measurement for water, air, steam, or refrigerant.

4.1 Orifice, nozzle, and venturi meters.
D hw
(1/2)
M = 0.01252 (C Y d 2 Fa) [-- ]
(For SI)SE-36
A
(1 - B )
D hw
(1/2)
M = 358.93 (C Y d 2 Fa) [
]
(For Customary)
(1 " B*)
hw
2 (1/2)
Q = 0.01252 (C Y d Fa) [
]
(For SI)SE-37
D (1 - B*)
Page 24
. : )
hw
2 (1/2)
Q = 358.93 (C Y d Fa) [
]
(For Customary)
D (1 - BA )
If data from ASHRAE standards are used for calculation of flow

rates, the discharge coefficient C is combined with the term (1/(1 - B ) (1/2) )
A
and given as flow coefficient K. These equations become:
(1/2)
M = 0.01252 (K Y d 2 Fa) ( D hw ) (For SI) SE-38
(1/2)
M = 358.93 (K Y d 2 Fa) ( D hw ) (For Customary)
hw
2 (1/2)
Q = 0.01252 (K Y d Fa) ( ) (For SI) SE-39
D
hw
(1/2)
Q = 358.93 (K Y d 2 Fa) ( ) (For Customary)
D
Symbols
B *= ratio of d to pipe inside diameter, dimensionless

C = coefficient of discharge, dimensionless, look up in
orifice, nozzle, or venturi tables
D = density of fluid at primary element, kg/m 3 (lb/ft 3 )
d = diameter of orifice, nozzle throat, or venturi throat,
mm ( in.
Fa = area factor for thermal expansion of primary element,
dimensionless, look up in orifice, nozzle, or venturi
charts
hw = differential pressure of taps, mm (in.) of water
K = flow coefficient, dimensionless, look up in orifice,
nozzle, or venturi tables
M = mass flow rate, kg/h (lb/h)
Q = volume flow rate, m /h (ft3/h)
3
Y = fluid expansion factor, dimensionless, look up in charts
4.2 Positive displacement meter, turbine meter, and vortex shedding

meter
M = 3600 (D) (f / K) SE-40
Q = f / K (For SI) SE-41
Q = 60 (f / K) (For Customary)
Page 25
::
Symbols
D density of fluid, kg/m 3 (lb/gal)

*=
M = mass flow rate, kg/h (lb/h)

3
Q = volume flow rate, m /s (gpm)
f -= pulse frequency, Hz
K = calibration factor, pulse/m 3 (pulse/gal)
4.3 Variable area flow meter.
Vf x Gf (G f - G)
1/2
M = K a D w (---- ) SE-42
Af
When measuring liquid refrigerant flow, the meter should be

calibrated for the refrigerant at its flowing temperature. If the meter is
calibrated for water, the specific gravity of the refrigerant should be used
to adjust the measured flow rate by:
(1/2)
Mref = Mwater ( G ) SE-43
Symbols
a = annular area of flow, m 2 (ft 2 )
Dw = density of water, kg/m 3 (lb/ 3 )
G = specific gravity of fluid
Gf = specific gravity of float
GF = gravitational force of float, grams
K = flow constant
M = mass flow rate, kg/s (lb/h)
M ref = flow rate of refrigerant, kg/m 3 (lb/ft 3 )
Mwater = meter reading calibrated for water, kg/m
3
(lb/ft 3 )
V f = volume of float
5. Electric power. (Horsepower equations are for customary unit use only)
5.1 Single phase.
To calculate from measured wattage input.
Watt input
HP - SE-44
746
Page 26
To calculate from measured voltage, current and power factor. The

motor efficiency must be estimated.
I x E x Eff x Pf
HP - SE-45
746
5.2 Three phase. To calculate from watt meter measurement as given in

SE-45, or from measured voltage, current, and power factor. Efficiency of
motor must be estimated.
1.73 x I x Ex Eff x Pf
HP SE-46
746
where
E is the line potential, volts
Eff is the motor efficiency, %
Pf is the motor power factor, %
HP is motor horsepower, hp
I is the measured current, A
Page 27
,
EXHIBIT 2-C STANDARD TEST PROCEDURES
1. General. Standard test procedures which are used frequently are

described in this EXHIBIT. They are referenced within various chapters of
this guide.
2. Reference standards.
a. ASHRAE Standard 41.1 (Standard Measurements Guide: Section on
Temperature Measurements) describes instruments, measurement techniques, and
recommended practices for temperature measurement generally encountered in
HVAC equipment testing. The temperature range is limited between 4.4 to 204.4
°C (40 to 400 °F) The instruments covered are mercury- in- glass thermometers,
.
thermocouples, and resistance thermometers.
b. ASHRAE Standard 41.5 (Standard Measurement Guide: Engineering

Analysis of Experimental Data) describes definitions, recommended practices
and procedures for treating and reporting test data. Uncertainty analyses of
test data are discussed.
c. ASHRAE Standard 41.6 (Standard Method for Measurement of Moist Air

Properties) describes instruments, measurement techniques, and recommended
practices for measuring air humidity. It gives recommended calculation
procedures of moist air properties. Instruments included are psychrometer
dew point hygrometer, heated electrical salt-phase transition hygrometer,
Dunmore sensor, and electrolytic hygrometer.
d. ASHRAE Standard 41.7 (Standard Method for Measurement of Flow of Gas)

describes meter construction, measurement techniques, and recommended
practices for measurement of gas flow by orifice meter. Flow formulae are
given.
e. ASHRAE Standard 41.8 (Standard Methods of Measurement of Flow of

Fluids- -Liquids) is similar to the standard in d. above. This Standard is for
liquid flow measurement.
f. ASHRAE Standard 111-1988 (Practices for Measurement, Testing,

Adjusting, and Balancing of Building Heating, Ventilation, Air Conditioning
and Refrigeration Systems)
g. ASME PTC 19.3 (Temperature Measurement Instruments and Apparatus)

describes various temperature measurement instruments and recommended
measurement practices. Calibration methods of temperature instruments is also
given.
Page 28
.
h.ASME PTC 19.5 (Flow Measurement Instruments and Apparatus) deals with
flow measurement and is similar in purpose to the standard in f. above.
i.ISA MC-96.1 (Standard for Temperature Measurement Thermocouples)

describes principles and recommended practices of temperature measurement of
thermocouples
3. Permanently installed sensor locations. It is extremely important

that permanently installed field sensors as part of the contract be located
and installed correctly, even if site conditions make it difficult. A case in
point is the locations of primary elements for water flow rate measurements
(such as orifice plates). It is extremely difficult, if not impossible, to
get good test results during commissioning, if the primary element is
installed at a poor location for a large pipe. Good installation practices as
recommended by various engineering guide books (e.g. ASHRAE standards) should
be followed.
4. Simulation of sensors.
4.1 Reasons for simulating sensors. At the time of commissioning, a
sensor responds to only one condition of the controlled variable where the
sensor is situated. Therefore only one response of the control loop may be
observed. It is desirable to vary the controlled variable so that more than
one or a continuous set of responses may be tested. In most cases, it is not
practical to subject the sensor to the full range of possible changes.
However, a simulated change may be easily and accurately accomplished.
4.2 Principal of simulation. Responding to the controlled variable, a

sensor varies the output signal (pneumatic pressure, electric resistance or
voltage, etc.) transmitting to the controller at a predetermined relationship.
If this relationship is known, the sensor may be bypassed and an appropriate
signal fed into the controller to represent the controlled variable condition.
4.3 Preparation. There are numerous kinds of sensors used in detecting

different controlled variables in a project. The commissioning team must be
familiar with the project specifications and especially the submittals before
inspections and tests. The simulation procedures described in this guide are
the ones most commonly encountered.
4.4 Sensor simulation procedures.
4.4.1 Temperature, STP-1.
4.4. 1.1 Pneumatic control system.
* Obtain a temperature/air pressure relationship chart of
Page 29
. 2 . ,
the sensor from the contractor.
* Disconnect the sensor tubing at the controller and

replace with the output tubing of a portable pneumatic calibrator (simulator).
The building compressed air source for the control system or manual pressure
generator may be used for the calibrator.
* Manipulate the pressure output of the calibrator. This

1.2
output corresponds to a desired temperature simulation.
* Observe and record the responses of the equipment or

system.
* After test, restore the sensor pneumatic tube to the

controller after test. Make sure no leakage occurs afterward.
4. 4. Electric/electronic control system.
* Depending on the type of temperature sensing devices

installed, obtain a temperature/resistance, temperature/voltage, or
temperature/current chart. Note that not all temperature sensors of the same
type have the same charts
* Disconnect the output wires of the sensor at the

transmitter and connect a resistance simulator (for RTD or thermistor type
sensor) or a thermocouple simulator (for thermocouple type sensor).
* Manipulate the resistance or the voltage simulator

according to the charts to simulate the desired temperature.
4.4.2
* Observe and record the responses of the equipment or
system.
* Restore the original wires to the transmitter after

test
Humidity, STP-2.
4. 4. 2.1 Pneumatic system. Similar to the procedure outlined

in paragraph 4.4. 1.1 above, except that a humidity/air pressure chart is used.
4. 4. 2. Electric/electronic. Similar to the procedures

outlined in paragraph 4.4. 1.2 above, except that humidity/resistance
humidity/voltage, or humidity/current charts are used.
4.4.3 Air static pressure, STP-3.
4.4. 3.1 Connect the pressure calibrator to the pressure
Page 30
; 4
1
2
3
sensor of the system to be tested. Generate a gage or differential pressure

as outlined below.
4.4. 3. The pneumatic calibrator (simulator) may be

connected to a steady air pressure source.
4.4. 3. Manipulate the pressure calibrator to generate the

desired pressure output.
4.4.4 Observe and record the responses of the equipment
4. 4. 3.
or system.
Fluid flow, STP-4. Applies in testing of monitoring and

controlling of air, water, and steam systems to simulate different flow rates.
4.4.4. Disconnect sensing lines from the primary sensing

element to the unit receiving the sensed signal. Examples are:
* water sensing lines from orifice plate to transmitter;
* air sensing lines from pitot rake assembly to

transmitter
* electric signal lines from pulse generating meters (e.g.

turbine meter, vortex shedding meter) to pulse counter.
4. 4. 4. Connect signal simulator to the project signal

receiving unit. Examples of signal simulators are:
* water manometer;
* air pressure calibrator;
* count generator.
5. Measurement of air flow rate in duct, STP-5.

5.1 Select a location which is at least 7.5 diameters downstream from
any fitting which may cause air disturbance or a location at least 1.5
diameters downstream from straightening vanes for pitot traverse.
5.2 For round ducts divide the duct cross sectional area into at least
5 annular rings of equal area. Take 4 velocity pressure readings with pitot
tube in each ring along two diameters of the duct at right angles. Measured
from the center of the duct, pitot measurement positions are 0.316r, 0.548r,
0.707r, 0.837r, and 0.949r, where r is the radius of the duct.
Page 31
. . . . .
5.3For rectangular ducts divide the duct cross sectional area into at
least 16 sub -rectangles of equal area. Take one velocity pressure reading
with pitot tube at the center of each sub - rectangle
5.4If velocity pressure readings fluctuate the average of several

readings should be used for each measuring point.
5.5Calculate individual air velocity from each measured velocity

pressure by using SE-10 or SE-11.
5.6 Average individual velocities to obtain the averaged duct air

velocity.
5.7 Calculate volume flow rate of air by using SE-13.
5.8 Test work sheets for air flow rate measurement in round and
rectangular duct, WS 2C-1 and WS 2C-2, are included in the appendix.
6. Measurement of air flow rate across coil or filter face,

STP-6
6.1 Select a face downstream of coil or air filter. The sole selection
criterion is steady air flow with minimum air turbulence caused by
obstructions
6.2 Divide the coil or filter face into at least 16 sub-areas with the
maximum sub -area not more than one square foot.
6.3 Measure air velocity at the center of each sub-area. The

instrument used for the velocity measurement should be appropriate for the
velocity being measured. The instrument should be held perpendicular to the
face of the coil or filter. If the measurement is in a built-up casing, the
tester's body should not be allowed to interfere with the reading being taken.
6.4 Average individual velocities to obtain the averaged duct air

velocity
6.5 Calculate volume flow rate of air by using SE-13.
6.6 Same test work sheets for rectangular ducts may be used for
measuring at coils or at air filters.
6.7 Accuracy is considerably less than the results of pitot tube

measurement in ducts. Recommend to be used only when duct measurement is not
practical
Page 32
. . .
CHAPTER 3 REFRIGERATION PLANT
1. Scope. This chapter provides inspection and testing procedures for

refrigeration systems and associated heat rejection equipment. Refrigeration
machines included in this Chapter are centrifugal, absorption, and reciprocating
types. Heat rejection equipment includes cooling towers, air cooled and
evaporatively cooled refrigerant condensers.
2. Reference Standards.
a. ASHRAE Standard 15 - Safety Code for Mechanical Refrigeration.
b. ASHRAE Standard 20 - Methods of Testing for Rating Remote

Mechanical-Draft Air-Cooled Refrigerant Condensers.
c. ASHRAE Standard 30 - Method of Testing Liquid Chilling Packages.
d. ASHRAE Standard 64 - Methods of Testing Remote Mechanical -Draft

Evaporative Refrigerant Condensers.
e. ASHRAE Standard 90 - Energy Conservation in New Building Design.
f. ARI Standard 460 - Remote Mechanical Draft Air-Cooled Refrigerant

Condensers
g. ARI Standard 550 - Standard for Centrifugal or Rotary Water-Chilling

Packages
h. ARI Standard 560 - Standard for Absorption Water-Chilling Packages.
i. ARI Standard 590 - Standard for Reciprocating Water- Chilling Packages.
j. ASME Standard PTC-23 - Test Code for Atmospheric Water-Cooling

Equipment
k. CTI Bulletin ATC-105 - Acceptance Test Code for Water Cooling Towers.
3. Refrigeration System Inspection.

3.1 Refrigeration machines and components shall be inspected for their
construction and installation to meet safety and functional requirements. See
EXHIBIT 3-A for inspection procedures. See Appendix for inspection check lists.
Page 33
.

3.2
Heat rejection equipment and components shall be inspected for their

construction and installation to meet safety and functional requirements. ee
EXHIBIT 3-B for inspection procedures. See Appendix for inspection check liscs.
4. Refrigeration System Testing.

4.1 Equipment Testing General. Refrigeration machines and heat rejection
equipment, shall be tested for full load capacity, full and part load
performances, control sequencing, and safety protection. Startup and operating
tests are included.
4.2 False Load. If building

load at the time of testing does not
correspond to the specified capacity design conditions and/or commissioning
tests, a false load shall be introduced to make up for the building load
shortage. Precautions must be taken so that the introduction of false loads do
not damage the refrigeration equipment or any other building equipment, nor cause
excessively uncomfortable conditions in the building. See test procedure
appendices for options and procedures of applying false load.
4.3 Equipment Operation Prior to Test. If the refrigerating system has

been in operation for more than 80 hours, the heat exchanger surface of the
refrigeration machine should be cleaned before testing to meet the fouling
factors specified. However, since scaled tubes may cause tests to fail, the
burden of determining tube cleaning rests on the construction contractor and the
chiller manufacturer.
4.4 Manufacturer's Factory Testing. The project specification may allow

manufacturer's factory testing in lieu of field testing. Factory testing must
be witnessed by selected members of the commissioning team. The test intention,
test procedures, and acceptance criteria of this guide must be followed.
4.5 Centrifugal Refrigeration Machine Testing. See EXHIBIT 3-C for test
procedures
4.6 Reciprocating Refrigeration Machine Testing. See EXHIBIT 3-D for test
procedures
4.7 Absorption Refrigeration Machine Testing. See EXHIBIT 3-E for test
procedures
4.8 Heat Rejection Equipment Testing. See EXHIBIT 3-F for test
procedures
4.9 See Appendix for test work sheets.
Page 34
. . .
EXHIBIT 3-A INSPECTION PROCEDURES FOR REFRIGERATION MACHINES
1. General.
1.1 Review equipment manufacturer's instructions on start-up and operation
procedures
Give general inspection of refrigeration machine and associated

1.2
equipment, including base, vibration eliminating units, starting electrical
equipment, piping, etc. Be sure that no damage or rusting occurred.
Check equipment name plates to verify equipment model.

1.3 Compressor,
condenser, evaporator, and starter must have the same model numbers as approved
submittals
1.4 Check for headrooms and access spaces around the machine. The spaces
required in the design documents must be provided. Pay special attention to the
refrigeration machine heat exchanger tube replacement and cleaning spaces.
1.5 Verify installed pipe fittings and accessary equipment against project
drawings for completeness and proper installation. Fittings and accessories
include but not limit to valves, strainers, vibration elimination units,
thermometer wells, piping supports, etc.
1.6 Verify field installed wiring against project drawings and

manufacturer's submittals.
1.7 Check piping at equipment connections. Pipes should be supported from

building structure without undue stress on equipment (refrigeration machine,
pump etc )
, .
1.8 Check refrigerant relief pipe installation in accordance to project

drawings. If drawings do not indicate, all discharge pipes must terminate at
outside of building 4.6 m (15 ft) minimum from ground or 6.1 m (20 ft) minimum
from windows or doors. Pipe size must not be smaller than relief device opening
area
1.9 Check water flow direction marks for check valves and flow switches.
1.10 All moving parts (motors, belts, etc.) should have protection shields
for personnel safety.
1.11 Check alignment for all non-hermetic motor driven equipment (solution
and refrigerant pumps of absorption machines are usually hermetic type),
including motor, compressor, gear boxes, oil pump, purge pump, and water pumps.
Using some simple tools such as straight edges, square edges, plumb lines, and
strings yield good results. Also observe shaft and coupling for misalignment
Page 35
while machine is running.
1.12 Observe belt tightness of belt driven equipment. Use belt tension
gage if needed. Belt tension should be as recommended by belt manufacturer.
1.13 Check for completeness of required instrumentation, including

thermometers, gages, temperature and flow measuring and control devices. Required
straight pipe runs and arrangements for temperature and flow measuring devices
must be met.
1.14 Check electric equipment and controls for proper grounding.
1.15 Check all electrical connections for tightness.
1.16 For motor starter equipped with overcurrent heaters, check heater
sizes against starter manufacturer's recommendations. The recommendations are
usually contained in operator's manual or posted in starter cabinet.
1.17 If pneumatic pressure is used for system controls, check control air
system pressure.
1.18 Be sure the machine is charged with right kind of refrigerant. Check
sight glass for proper level.
1.19 Check for refrigerant leakage at component connections, shaft seals,

refrigeration pipe joints, and valves with electronic halogen leak detector. The
equipment room should be well ventilated to increase the sensitivity of
detection.
1.20 Make certain that the lubrication material used satisfy the
manufacturer's recommendations. Lubrication are required for compressor
bearings, motor bearings, gear trains, and other equipment. Oil level must be
as recommended.
1.21 Check thermal insulation for damages and omissions.
1.22 Check surface paint for damages and omissions. Equipment nameplates
must not be painted over. Required equipment labels must be present and legible.
1.23 No leakage should be noted for water, oil, refrigerant, steam, and
other fluid (such as lithium bromide).
1.24 Check vibration elimination units. The chiller or its sub-base

should float freely on springs or resilient pads without solid objects
transmitting vibration from chiller to base.
1.25 Note any unusual noise and vibration at varying load conditions.
Page 36
. .
2. Centrifugal refrigeration machine.

2.1 Inspect alignment at points of connections for field assembled
machines (see paragraph 1.11 above for alignment tools).
2.2 Be sure that temperature and pressure indicators for oil system are
functioning properly to indicate the oil system operation.
2.3 Regardless of the oil pump arrangement, the oil pressure supplied to
the compressor bearings and gear box must meet the minimum pressure requirement
specified by the manufacturer whenever the compressor is running (including
coastdown) .If a separate oil pump is used for start-up only, observe the
switch-over operation of the start-up pump and the main oil pump to insure proper
oil pressure at all times.
2.4 Check compressor interlocking function with oil pressure to insure the
operation of paragraph 2.2 above.
2.5 Be sure oil pump is wired separately from circuit feeding to the
compressor
2.6 Be sure oil filter is properly installed in oil pumping system and it
is clean.
2.7 Check oil heating system for proper operation. Oil sump temperature
must not be lower than the manufacturer's recommended temperature for proper
separation of refrigerant. Be sure the oil temperature control system is
operating properly.
2.8 Check oil cooling system for proper oil temperature control and
operation. Oil temperature shall not be over the manufacturer's recommended
temperature
2.9 Be sure necessary piping accessories (valves, strainers, etc.) are

installed in oil cooling system cooling water lines.
2.10 Observe compressor pre-rotation damper operation for the entire

capacity range. The damper control system (actuator and linkage) should have
smooth operation without fluttering.
2.11 Be sure compressor pre-rotation dampers do not open before compressor

reaches full speed.
2.12 Note unusual noise and vibration of compressor, bearings, gear box,
and motor.
Page 37
.
3. Absorption refrigeration machine.

3.1 Absorption refrigeration machines are sensitive to capacity control
at low condensing water temperature. Control line pneumatic pressure, steam
valve, water thermometer and 3 -way condenser water valve need to be checked for
proper calibration.
3.2 Check pump lubricant (usually water or salt solution) system strainer
and magnetic strainer for cleanliness.
3.3 Check strainers and traps for steam and hot water supply lines for
cleanliness, and condensate piping for proper type of steam traps and vacuum
breakers. Check for proper placement and orientation of same.
3.4 Cleaning of condenser tubes due to fouling is more important for

absorption chillers than other types of chillers because of higher condenser
water temperature of absorption chillers. The Team should note the time length
of the chiller in operation prior to the time of inspection and signs of fouling.
If fouling is suspected, a decision of cleaning condenser tubes should be made
with the construction contractor and chiller manufacturer's representative.
3.5 At the time of commissioning inspection, the chiller should have been
adjusted and charged properly by manufacturer's representative. The Team shall
obtain charge data sheet (lithium bromide and additives). If solution samples
have not been drawn for concentration tests, samples should be gathered when the
chiller is in operation (see EXHIBIT 3-E).
3.6 Check relief pipe installation for chiller pressure relief device in
accordance to project drawings. If drawings do not indicate, relief pipe from
steam chiller must terminate at outside of building and relief pipe from hot
water chiller must terminate at a floor drain. Pipe size must not be smaller
than relief device opening area.
4. Reciprocating refrigeration machine.

4.1 Be sure that temperature and pressure indicators for oil system are
functioning properly to indicate the oil system operation. Oil pressure must be
as recommended by the manufacturer.
4.2 Check compressor interlocking function with oil pressure to insure the
operation of paragraph 4.1 above.
compressor
4.4 Be sure oil filter is properly installed and clean.
4.5 Check oil heating system for proper operation. Electric wiring should
Page 38
.
be verified as per manufacturer's submittals or checked to be sure that crankcase

heater power is on even when the main power is off. The crankcase heater should
be installed snugly in its position. It should be on during compressor off time.
4.6 Check oil level before and during operation. Oil should not be
foaming excessively.
4.7 For chillers with remote condensers, check refrigerant pipe pitch and
oil traps for proper oil return.
4.8For air cooled and evaporatively cooled chillers, spaces for air
circulation is important. Be sure that manufacturer's recommendations are
followed and air is not short circulated from discharge to intake.
4.9 Check direction of fan rotation for air cooled condenser.
4.10 For air cooled condensers equipped with damper controls for low
ambient operation, check damper mechanism for proper adjustment and operation.
4.11 Check direction of fan rotation for evaporative condenser.
4.12 Check water level of evaporative condenser. Water float valve shall
not "chatter". Spray nozzles should have correct pattern without blockage.
There shall be no excessive water carry- through
4.13 If evaporative condenser is specified and equipped with bleed-off

arrangement, visually check valve adjustment for flow.
4.14 Check electric interlocks with condenser water pump and chilled water
pump. Check operation of flow switches.
5. Brush cleaning system for refrigeration machine.

5.1 This inspection procedures apply to refrigeration machines equipped
with automatic or manually initiated, built-in brush cleaning system for cleaning
condenser tubes. Consult project specifications for required specific features
of the tube cleaning system.
5.2 Visually inspect installed components. They may include manual

valves, flow diverting valve, pneumatic valve actuator, solenoid valve timer for
,
cycle control, manual override, indicating lights for power and diverting valve
positions, diverting valve speed control and indicator, cleaning cycle counter,
flow switch bypass, alarms, and control panel.
5.3 Check the function of manual override for actuating the cleaning
action.
Page 39
5.4 Check diverting valve actuation speed to meet the limitations of the
manufacturer's recommendations. Be sure the speed adjustment setting is secured.
5.5 Observe water flow and brush cleaning action for both forward and
reverse travels. Indicating lights and diverting valve action should agree.
5.6 The time between forward and reverse cleaning actions should be as
recommended by manufacturer.
5.7 Manually initiate cleaning action at least three times to ensure

proper operation.
5.8 Observe timer function. Timer should be set to actuate cleaning

action at desired intervals and time. Avoid setting time for cleaning condenser
tubes at high cooling load hours.
5.9 For manually operated systems, be sure the operation of shut-off

valves and/or diverting valve will not cause water hammer damage.
5.10 Check cleaning cycle counter for proper counting.
5.11 Be sure proper lubrication is applied to flow diverting valve and

valve actuator.
5.12 Record inspection data and final settings.
5.13 See EXHIBIT 3-C for leaking test of flow diverting valve.
Page 40
.
EXHIBIT 3-B INSPECTION PROCEDURES FOR HEAT REJECTION EQUIPMENT
1. General.
1.1 Review equipment manufacturer's instructions on start-up, operation
and maintenance procedures.
1.2 Give general inspection of heat rejection equipment and its associated
equipment, including base, vibration eliminating units, starting electrical
equipment, piping, valves, etc. Be sure that no damage occurred during
construction.
1.3 Check equipment name plates to verify equipment model. Cooling tower,
heat exchanger, and their auxiliary equipment must have the same model numbers
as approved submittals.
1.4 Check for clearance space, access doors, ladders, lightening

protection, grates, and guard rails for completeness. Manufacturer's recommended
access spaces must be provided. There shall be no obvious obstruction to air
circulation.
1.5 Verify installed piping and accessary equipment against project

drawings for completeness and proper installation. Pipe fittings and accessories
include but not limit to valves, strainers, vibration elimination units,
thermometer wells, pressure gages, piping supports, etc.
1.6 Verify installed wiring against project drawings.

building or ground support unless project drawings or approved submittals allow
supporting on cooling tower.
1.8 Check fluid flow direction marks for check valves and flow control
valves
1.10 Check alignment for all motor driven equipment, including motor, gear
boxes, fans and water pumps. Using some simple tools such as straight edges,
square edges, plumb lines, and strings yield good results. Also observe shaft
and coupling for misalignment while machine is running.
1.11 Observe belt tightness. Use belt tension gage if needed. Belt
tension should be as recommended by belt manufacturer.
Page 41

must be met.
1.15 Make sure that fan motor is of the type as specified.
sizes with starter manufacturer's recommendations. The recommendations are
1.17 If pneumatic pressure is used for system controls, check control air
system pressure.
1.18 Make certain that the lubrication material used satisfy the
manufacturer's recommendations. Lubrication are required for fan bearings, motor
bearings, gear trains, and other equipment. Oil level must be as recommended.
External extended grease lines must be provided if specified.
1.19 Check thermal insulation for damages and omissions (for cooling tower
winterizing auxiliaries, if required in specifications).
1.21 Check vibration elimination units. Equipment should float freely

on springs or resilient pads without solid objects transmitting vibration from
equipment to building.
1.22 If winterizing equipment is specified, they shall be inspected and

checked in according to the specifications.
1.23 Observe correct direction of fan rotation.
1.24 Note any unusual noise and vibration.
2. Cooling tower and evaporative condenser.

2.1 Inspect water basin for cleanliness.
2.2 Verify overflow and drain pipes (Drains are usually specified to be
piped to sewer) Check for outlet basin screen, if specified.
.
Page 42
. .
2.3 Water should not spill over hot water basins and cold water collection
basin during any time of the operation. There should not be excessive splash
over air inlet or excessive carryover from air discharge.
2.4 Observe makeup valve and float mechanism for proper operation. Water
level of the cold water collection basin should as recommended by the
manufacturer. For equipment specified with constant bleeding, observe the amount
of makeup to be approximately correct.
2.5 Observe water distribution orifices for blockage.
2.6 For equipment with spray nozzles, turn fan off (condenser water pump
is on) and observe nozzle spray pattern and blockage.
2.7 For cooling towers having more than one cell, observe water
distribution pattern for obvious imbalance of balancing valves or distribution
valves. Water level in hot water basins should be as recommended by the
manufacturer
2.8 For field assembled towers, check material (fill, frame, casing,
baffle, water distributing plate, etc.) and installation against specifications
and approved submittals.
2.9 Check cooling tower support structure with details shown on

construction drawings or approved submittals to assure adequacy of support.
2.10 For tile filled towers, check tile supports against manufacturer's
shop drawings.
2.11 Check that water treatment system is operational and adjusted. Check
interlock of chemical pump with condenser water pump (or other interlock as
specified)
Page 43
EXHIBIT 3-C CENTRIFUGAL REFRIGERATION MACHINE TEST PROCEDURES
1. Scope. The test procedures described in this EXHIBIT apply to packaged

refrigeration machines using electric driven centrifugal compressors for
refrigerant compression to achieve cooling effects. Electric motors may be open
or hermetic types. The machines produce chilled water and their condensers are
supplied with cooling water externally.
2 . Purpose
2.1 To verify full capacity of the installed refrigeration machine for
meeting the specified capacity without exceeding the specified power input.
2.2 To verify part load power consumption of the machine not exceeding the
specified part load power limits at the specified part loads.
2.3 To verify other limiting conditions set in the project specifications,

such as maximum water side frictions of the heat exchangers.
2.4 To verify ability of cooling capacity control of the machine without

encountering undesirable effects.
2.5 To verify operations of all components meeting their intended

functions
2.6 To verify safety operation of the machine.
3. Industry standards.
3.1 ARI Standard 550 (Standard for Centrifugal or Rotary WAter chilling
Packages) prescribes requirements for testing of centrifugal refrigeration
machines. It specifies the basis for testing, rating, and publishing of
capacities and power requirements. Power input is measured for the compressor
only. These machines are tested and rated under the following conditions:
Leaving chilled water temperature 6.7 °C (44 °F)

Chilled water flow rate 0.043 L/s per kW (2.4 gpm/ton)
Entering condenser water temperature 29.4 °C (85 °F)
Condenser water flow rate 0.054 L/s per kW (3.0 gpm/ton)
Refrigerant side fouling factor 0.0000 m 2 °C/W (.0000 hr ft 2 F/Btu)
Water side fouling factor 0 .000044 m 2 °C/W (0.0005 hr ft 2 F/Btu)
Page 44
.
3.2 Among other requirements, ARI Standard 550 lists the following
required safety and operating controls:
Refrigerant high-pressure cutout

Freeze -protection cutout
Provision for interlocks to stop compressor operation upon failure
of chilled water flow
Low oil-pressure cutout
Compressor over-speed trip (for non-electric motor drives)
Chilled water temperature controller
Compressor motor load limit control
ARI Standard 550 also requires that the water side of the evaporator
3.3
and condenser be suitable for a working pressure of 1034 kPa (150 psig) Verify .
exact pressure rating required and installed.
3.4ASHRAE Standard 30 (Methods of Testing Liquid Chilling Packages)

describes methods of testing of liquid chilling refrigeration machines for their
performance ratings. This standard does not specify the test conditions. Power
measurement is for compressor driver and all auxiliaries.
3.5 ASHRAE Standard 15 (Safety Code for Mechanical Refrigeration) covers

a much wider range of requirements than the refrigeration machine itself. Its
purpose is to assure the safe design, construction, installation, operation, and
inspection of refrigeration systems.
3.6 ASHARE Standard 90 (Energy Conservation in New Building Design) sets

forth the requirements for the design of new buildings, including energy
performance of HVAC equipment. The energy input to all auxiliary components of
the refrigeration machine is included (consistent to ASHRAE Standard 30
requirements). See the latest edition for minimum performance requirements.
4. Preparation for test.

4.1 It is assumed that, before the scheduled test, the project contractor
or manufacturer's representative has prepared the refrigeration machine in
according to the recommendations of the manufacturer for startup and operation
and an inspection of the refrigeration system by the Team has taken place (see
EXHIBIT 3-A for inspection).
4.2 All measurement and test instruments must be calibrated before

testing, unless documents can be shown satisfactorily that the instruments are
in calibration (see Chapter 2 for calibration of instruments) Instruments.
supplied with the machine may be used to take test data after they have been
calibrated and the accuracies satisfy the minimum tolerance requirements of
tests
Page 45
4.3 In most cases, a false load is needed for full load performance test.
Depending on individual project circumstances, false load may be introduced at
the equipment room close to the refrigeration machine to be tested or to the
building equipment installed as parts of the building facility (such as air
handling systems). The former approach may require temporary equipment (such as
temporary boiler or heat exchanger) to provide heat source, piping from the heat
source to the refrigeration machine and/or cross-over piping between the
condenser and the evaporator, and accessories such as shut-off Valves and
temperature controlling mixing valves. The Team should review the piping layout
to be sure that water entering both evaporator and condenser may be adjusted
individually to those of the specified values. The disadvantage of the latter
approach is the long lagging time for the temperature at the refrigeration
machine to stabilize (from the time to introducing false load at the air handling
systems to achieve stable and desired conditions at the test machine) . After it
is determined the approach to take based on cost comparisons, good coordination
between all involved parties is essential.
4.4 The heat exchanger tubes may not be clean to yield the specified
fouling factors. Oil film needs to be cleaned when tubes are new. If the
refrigeration machine has been running for some time to provide temporary
cooling, the tubes should be cleaned before tests. This is especially important
for condenser tubes, because of the low quality of the condenser water and higher
temperature of the tube surface. It is difficult to measure the actual fouling
factor or scale thickness in the field. Only actual cleaning will assure the
correct performance of the machine. The Team should obtain a written statement
from the contractor or witness the cleaning operation that the tubes are cleaned
according to the manufacturer's recommendations (such as using chemicals). If
the machine has been in operation, physical cleaning with rodded brushes may be
necessary unless the refrigeration machine has automatic brush cleaning equipment
and the frequency of cleaning has been set correctly since the refrigeration
machine was in operation.
5. Recommended tests.
5.1 Full load test. The refrigeration machine must deliver the specified
cooling capacity under the specified conditions. The specified conditions may
be different from the basis of the manufacturer's published and selected
conditions. The project specification usually also specifies the entering
condenser water temperature, the leaving chilled water temperature, the condenser
water and the chilled water flow rates, the maximum power consumption rate at
these conditions, and the maximum water friction loss of the two heat exchangers.
Each of these ratings or limitations must be verified by testing directly or
verified by deducing from test data (see paragraph 7.3 for test procedures).
5.2 Part load test. Depending on the refrigeration machine's part load
performance curve, the energy performance of a machine may vary considerably.
In order to have optimum energy performance for the entire cooling season,
several points of the performance curve may be specified to define a skeleton
Page 46
. .
performance curve. The commonly specified points are at 75%, 50%, 25% of the
full load, and/or the lowest desirable stable load. The test conditions for the
part load may be different from those of the full capacity test conditions,
depending on the specifications (see paragraph 7.4 for test procedures).
5.3 Capacity control test. With reduced load the machine should respond
by reducing its capacity and vice versa. The test should verify the automatic
capacity change following load changes without running into unstable conditions
for the entire range of capacity from full load to minimum load as specified.
Project specifications usually do not allow hot gas bypass above 10% of full
load. Therefore, the test should also show the hot gas bypass operation to be
compared with the specifications and the equipment manufacturer's claims (see
paragraph 7.5 for test procedures).
5.4 Safety control test. To test the refrigeration machine's safety

controls so that it will not be damaged during unforeseen events. In additions
to the controls required in ARI Standard 550 (see paragraph 3.2, Industry
Standards, of this EXHIBIT), all other safety control features should also be
tested (see paragraph 7.1 for test procedures).
5.5 Auxiliary equipment operation test. Centrifugal refrigeration machine

usually has oil pumping system, non-condensable purge system, and/or refrigerant
pumpout system. Some refrigeration machines are specified with built-in brush
cleaning system or separate add-on cleaning system. All these auxiliary systems
6.1 tested (see paragraph 7.2 for test procedures).
shall be
5.6 Cooling plant system test. This test involves interlocking of

condenser pump, chilled water pump, cooling tower operation, and other cooling
plant components, such as sequencing of chillers (see paragraph 7.6 for test
procedures)
6. Instrumentation. The required measurement, minimum accuracies, and

measurement precautions are given below:
Temperature.
6.1.1 Chilled water temperature leaving evaporator. The measurement

system error shall not exceed +/- 0.1 °C (0.2 °F).
6.1.2 Direct measurement of temperature differential of the chilled

water entering and the leaving evaporator. This measurement is preferred than
deducing the difference from separate temperature measurements at the entering
and the leaving chilled water, since it minimizes the errors of calibration of
two temperature measurements. The measurement error shall not exceed +/- 0.1 °C
(0.2 °F)
Page 47
6.1.3 Condenser water temperature entering condenser. Total

measurement error shall not exceed +/- 0.1 °C (0.2 °F) .
6.1.4 Direct measurement of temperature differential of the

condenser water entering and the leaving condenser for the same reason as given
for chilled water measurement. Same accuracy requirement as for chilled water,
+/- 0.1 °C (0.2 °F)
6.1.5 The temperature sensor locations of these four measurements

are important. They should be located to sense well mixed bulk water
temperature. If chilled water or condenser water is used to cool any component
of the refrigeration machine, the temperature sensors must be located to include
the effects of this cooling.
6.1.6 The thermometers or temperature gages, supplied as integral

parts of the ref rigeration machine such as for bearing, oil, refrigerant, etc.,
,
shall be calibrated to have errors less than +/- 0.6 °C (1 °F) .
6.2 6.1.7 Temperature sensors and thermometers are usually installed in

wells. They may be calibrated in laboratory or in field. Wells should be filled
with thermal conducting compound to insure good thermal contact between the well
and the sensing element.
6.1.8 If proper thermometer wells are not available, an insulated

extension to a vent valve allowing water to flow continually across thermometer
bulb may be used.
Water flow rate.
6.2.1 Chilled water pipe. The total error of combined sensing and
readout devices shall not exceed +/- 3% of measured quantity.
6.2.2 Condenser water pipe. The total error of combined sensing and
6.2.3 It is very important to check if the primary element location

of flow meters are appropriate.
the The minimum pipe lengths upstream and
downstream of the primary element must be not less than those given in Chapter
2. Avoid areas where water flow may be swirl (e.g. after consecutive elbows).
If space is tight provision for the use of flow straighteners is very helpful.
6.2.4 If chilled water or condenser water is used to cool any

component of the refrigeration machine, the primary element of the flow meter
must be located to include the effects of this flow.
6.2.5 In the majority of installations the water flow rate of

centrifugal refrigeration machine does not vary. For a constant flow rate the
type of flow meters to be used for permanent installation or just for
commissioning tests can be easily selected. If differential pressure type
Page 48
(orifice plate or venturi, etc.) is used, the primary element with the largest
throat diameter that still satisfies the required accuracy should be selected to
minimize the friction loss associated with the measuring element.
6.3 Pressure instrument.
6.3.1 For differential pressure type primary element - water or

mercury manometer, or electronic pressure readout unit. Manometers should read
accurately to +/- 24.9 Pa (0.1 in. of water). Total error of primary element and
readout unit shall not exceed +/- 3% of flow.
6.3.2 The pressure instruments supplied with the machine as a

package, such as pressure gages for oil pressure and refrigerant pressure shall
be calibrated in laboratory or in field. When these instruments are taken off
the machine, exercise caution so that the media to be sensed shall not be in
contact with the atmosphere.
6.3.3 Pressure gages are usually specified and installed at inlet

and outlet of heat exchangers. These instruments may be used to verify the heat
exchanger water pressure drops.
6.4 Energy measurement.
6.4.1 Polyphase watt meter or watthour meter. Error shall not

6.4.3of reading.
exceed +/- 0.5%
6.4.2 Measurement of energy shall include that consumed by

compressor and auxiliaries. This requirement differs from that of ARI Standard
550.
Check and record electric voltage between feeders and the

frequency at the power supply.
7. Test procedures. Refrigeration machine manufacturers usually have

detailed check out procedures after field installation for their particular
models. The following test procedures are designed to be generic and should be
used as guidelines only. Since the test agent is responsible for performing
tests and for demonstrating meeting construction documents, the Team must examine
all details of installation and operation manuals provided by the manufacturer
and coordinate with the testing agent to modify the test procedures given in this
guide. However, the intended purpose of these test must be carried out and their
acceptance criteria must be satisfied.
7.1 Safety control test. This test should be performed before other tests
after an inspection. Some situations requiring pressure and temperature to
trigger control actions are not appropriate to test on line. Therefore these
tests are limited to checking safety control circuits with simulated controlled
Page 49
variables. In some cases (refrigerant pressure, oil pressure, etc.), they are
tested indirectly without creating simulated controlled variables (pressure)
Indicating lights, relays, actuators, and controlled components of the machine
are used to confirm the control action.
7.1.1 Make sure area is clear of personnel .

- IMPORTANT
7.1.2 Check voltage balance of electric power service. The maximum

voltage deviation from average of three voltage measurements should not be
greater than +/- 11 of the average. In equation form, it is:
(A, B, or C) - (A + B + C) / 3
% voltage imbalance -
(A + B + C) / 3
where A, B, and C are voltage measurements between phases.
7.1.3 Disconnecting electric power to the compressor is the next

step. Depends on the wiring configuration, the power leads to the compressor may
have to be physically disconnected. Do not rely on automatic wiring arrangement
for disconnecting compressor.
7.1.4 Connect power to control circuits and auxiliary equipment

circuits. Control circuit usually have separate disconnect.
7.1.5 Test all pilot lights and alarms by pressing the appropriate
buttons
7.1.6 Simulate compressor running by turning on the compressor

switch. Indicating light for compressor should show "on".
7.1.7 At this stage of testing, all temperature and pressure

indicators should have been calibrated already.
7.1.8 Test temperature actuated safety controls. Set temperature

bath to the trip temperature of the control as recommended by the refrigeration
manufacturer. Remove temperature sensors from wells and place in temperature
bath. Vary the bath temperature +/- 1.1 °C (2 °F) slowly. By observing the
pilot lights, the make and break points of the chiller circuits shall be
recorded. Also record the set point of the temperature switch. The tolerance
of the set point and the actual break point shall not exceed 0.6 °C (1 °F) The .
temperature switches to be tested shall include, but not limited to, the
following:
7. 1.8.1 Refrigerant low temperature cutout.
7. 1.8. Refrigerant high temperature cutout.
7. 1.8. Chilled water low temperature cutout.
Page 50
. . . —
7. 1.8. 4 Oil heater thermostat control.
7.1.9 Test pressure actuated safety controls. For safety reasons

pressure actuated safety switches are not provided with valves to be isolated
from the chiller. Pressure gages (already calibrated) located at the switch
sensing areas can be used indirectly to check the functions of these switches.
Move the switch setting slowly up above the manufacturer's recommended pressure
and observe the pilot lights. Do likewise while moving the setting down slowly.
Record the pressure (as indicated by the pressure gage) where it trips the
compressor running circuit. The tolerance of the recommended and actual tripping
pressures shall not exceed +/- 3% of recommended values. Pressure switches to be
tested shall include, but not limited to, the following:
7. 1.9.1 Condenser high pressure cutout.
7. 1.9. 2 Evaporator low pressure cutout.
7. 1.9. 3 Low oil pressure cutout.
7.1.10 Test flow actuated safety controls. Bypass the flow switches
of evaporator and condenser water at the switches by using jumper wires and
observe pilot lights. This does not indicate the functioning of the flow sensing
mechanism which will be verified later in full load test.
7.1.11 Reconnect motor wires. Be sure to observe safety procedures.
7.1.12 Data to be recorded (Not all items are required for the same
machine. See project specification and submittals for items required and
installed) :
i
1
—
rH CM »
) Mechanical equipment room temperature.
7.1.12.2 Cutin and cutout temperature of refrigerant low and

high temperature safety.
7.1.12.3 Cutin and cutout temperature of chilled water low

temperature control
7.1.12.4 cutin and cutout temperature of oil heater

thermostat
7.1.12.5 Cutin and cutout pressure of condenser high pressure

safety
7.1.12.6 Cutin and cutout pressure of evaporator low pressure

safety
7.1.12.7 Cutin and cutout pressure of oil pressure safety.
Page 51
7.2 7.1.12.8 Operation of chilled water and condenser water flow

switches
Auxiliary equipment test. This test should be performed after the

cooling tower7.2.1
water circuit has been tested, adjusted and balanced.
Start condenser water pump. Check pump amperage for possible

overload.
7.2.2 Check condenser water flow rate. This should be done after
cooling tower is readied for operation. The installed condenser water pump
(permanent or temporary) may not give the correct flow rate. If the flow rate
differs from that of the specified rate, adjust flow balancing device on
condenser water line to the required rate.
7.2.3 Check temperature of entering condenser water. The cooling

tower temperature control should be adjusted to provide the desired condenser
entering water temperature.
7.2.4 Start chilled water pump. Check pump amperage for possible
overload.
7.2.5 Check chilled water flow rate. Adjust flow balancing device
if necessary.
7.2.6 Although the following items may have been checked during
inspection at the beginning of the functional performance testing, they shall be
checked again for running tests as routine startup procedure.
7. 2. 6.1 If pneumatic control is used, check air supply system.
7.2.7 7. 2. 6. Check oil and refrigerant levels.
7. 2. 6. Check oil sump temperature. The manufacturer's

recommended oil temperature should be maintained for at least 24 hours or the
duration as recommended by the manufacturer. The oil temperature control
thermostat is tested in the previous paragraph. This step confirms the entire
oil heater function.
If temporary cross-over piping connections are used for

providing false load, adjust flow control valves on cross-over piping to give
both condenser and chilled water the correct flow rate.
7.2.8 Test oil system.
7. 2. 8.1 Be sure cooling water is supplied to the oil cooling

system
7. 2. 8. Be sure oil filter is clean (should have been checked
Page 52
. 4
5
3 .
during inspection)
7. 2. 8. Turn on oil pump.
7. 2. 8. Record oil pressure. Record temperature at sump, oil

cooler, and compressor bearing. The manufacturer's pressure requirements must
be met.
7.2.9 7. 2. 8. Oil pressure during coastdown is tested later in part

load test.
7.2.10 Test automatic purge system by switching controls to manual

position. Manufacturer's recommended test procedures should be followed.
Test refrigerant pumpout system by following manufacturer's

recommended procedures. If a reciprocating machine is specified and installed
for the pumpout system, it shall be switched on for at least half hour and the
following data recorded:
7.2.10.1 Discharge pressure.
7.2.10.2 Suction pressure or temperature.

7.2.11
7.2.10.3 Oil pressure.
7.2.10.4 Condenser water entering and leaving temperature.
Test condenser brush cleaning system. The inspection

procedures for condenser brush cleaning system are given in EXHIBIT 3-A. In the
inspection procedure, most of the functional testing of the system, such as for
manual override to initiate operation, checking of diverting valve actuation
speed, timer action between forward and reverse cleaning, counter operation,
etc., have been performed. During auxiliary equipment test the diverting valve
should be tested to be certain that the valve is not leaking condenser water from
supply pipe to return pipe. This is especially important during normal mode of
operation of the condenser (brush cleaning system not in operation)
7.2.11.1 Attach two 0.025 m (1 inch) thick, 0.15 m by 0.15 m

(6 in. by 6 in.) minimum size mineral wool thermal insulation on condenser water
return pipe (water leaving condenser) at locations on both sides of the flow
diverting valve approximately 0.30 m (3 feet) from the valve. This is to minimize
the influence of ambient air on pipe surface temperature measurement.
7.2.11.2 Insert temperature sensor of a portable digital

thermometer under the insulation covers and take temperature alternately between
these two locations with the same thermometer. Take three sets of temperature
readings (a total of six readings) Five minutes should
. be allowed between
insertion of sensor and temperature taking for each reading. The time to perform
this test should be when the refrigeration machine is close to fully loaded and
Page 53
the refrigeration machine is running at approximately stable conditions.

7.2.11.3
7.3 The temperature difference between the averaged three
readings of the same locations shall not be greater than 0.5 F.
Full load test. This test follows auxiliary equipment tests with
chilled water and condenser water pumps in operation.
7.3.1 Set chilled water supply temperature setting to the specified

full load supply temperature.
7.3.2 Start the refrigeration machine.
7.3.3 Observe the rotation direction of motor and compressor to be

correct
7.3.4 The running of compressor proves that the evaporator water and
condenser water flow switches are functioning (see previous description on safety
tests)
7.3.5 Load the machine by following manufacturer's recommendations.
7.3.6 With constant flow rate, the temperature differential of the

evaporator indicates the loading condition of the refrigeration machine. In most
cases false load will be required to achieve the specified capacity.
7. 3. 6.1 If false load is applied to the building equipment,

heating media should be added gradually and in incremental manner so that no
overloading of air handling equipment and test refrigeration machine occurs.
Considerable amount of time may be needed to have the entire system stabilized
at the desired temperatures. The Team should evaluate the natural building load
(internal load and weather) at the time of test to fully utilize these loads so
that the amount of false load may be kept to a minimum.
7. 3.6.2 If false load is applied to the temporary heating

equipment and/or crossover piping between the condenser and evaporator, heat
should be added gradually and cross over valves manipulated to give the specified
temperature differentials of both condenser and chilled water. The water flow
rates of the condenser and evaporator should be checked constantly to maintain
the specified rates.
7.3.7 While load is being increased, monitor the compressor current

draw. The maximum current shall not exceed the specified demand limit.
7.3.8 Adjust chilled water leaving temperature setting slightly down

to initiate opening of compressor prerotation vanes and observe the operation of
vane actuator. The operation of vane actuator shall not "hunt".
Page 54
.
7.3.9 Condenser water temperature control and/or cooling tower

control may need to be adjusted to obtain the specified condenser water
conditions at full load. If during the time of test the outside air wet bulb
temperature is higher than that of the specified for the cooling tower and the
specified condenser water temperature is not attainable (chances of this is
rare),
the test must be postponed until the outside air wet bulb temperature
drops below the specified value of the cooling tower.
7.3.10 After water flow rates and temperature of both condenser and
evaporator have achieved the specified values, the refrigeration machine shall
run for a minimum of one (1) hour. Data shall be recorded at 10 minute
intervals. Minor adjustment of water flow rates and temperature may be needed
during this period. The test setup is considered stabilized and test data for
full load performance may be taken, if 3 sets of data (30 minutes total time),
after any adjustment, are within the tolerances as listed below:
7.3.10.1 Water flow rate +/- 5% of specified values;
7.3.10.2 Water temperature +/- 0.6 °C (1 °F) of specified

values
7.3.11 Data shall be taken at 10 minute intervals. A minimum of

three sets of data shall be averaged for capacity and energy calculations.
7.3.12 Data to be recorded:
7.3.12.1 Chilled water leaving temperature.
7.3.12.2 Chilled water differential temperature.
7.3.12.3 Condenser water entering temperature.
7.3.12.4 Condenser water differential temperature.
7.3.12.5 Chilled water entering and leaving pressure.
7.3.12.6 Condenser water entering and leaving pressure.
7.3.12.7
7.3.12.9 Chilled water flow primary element differential
pressure or other flow instrument output.
7.3.12.8 Condenser water flow primary element differential

Wattmeter output.
7.4 Part load tests. Part load tests should follow immediately after the
full load test. Unless the part load conditions are specified in the project
specification (in cooling capacity or percentage of full load), part load tests
Page 55
shall be performed at 75%, 50%, and 25% of the full load cooling capacity. The
chilled water leaving, condenser water leaving and condenser water entering
temperature shall be the same as for full load test, except for 25% capacity test
where the entering condenser water temperature shall be 19.1 °C (66.3 °F) The
.
chilled water temperature differentials shall be as calculated from equation

expressed in Section 8.2 for part load cooling output.
7.4.1 Reduce machine load by the combination of the following ways:

reducing the building load; reducing the false load; manipulating the crossover
valves; and manipulating the plant chilled water mixing control valve on the
chilled water return pipe. The new load shall be stabilized at the largest part
load under the full load.
7.4.2 Adjust condenser water temperature control to the specified

value of the part load.
7.4.3 Follow the same procedures as outlined previously for full

load test (steps 7.3.9 through 7.3.12), except that pressure measurements at
entering and leaving points of evaporator and condenser need not be performed.
7.4.4 Repeat the same procedures for all other part load tests. If
unstable conditions of compressor occur (surge), abort the test. Follow
manufacturer's recommended procedures to stop the compressor operation. See
capacity control test later for detecting compressor surge.
7.4.5 Cut off all false load and restore all valves to their normal
operation modes
7.4.6 When the compressor is coasting down, observe and record the
oil pressure gage. The oil pressure shall not be lower than the recommended
pressure as long as the compressor shaft is turning.
7.5 Capacity control test. This test is performed concurrently with the
full load and part load tests. The purpose of this test is to verify the correct
sequencing of the operation when the load changes.
7.5.1 After the full load test, set the chilled water leaving
thermostat up slowly till the start of compressor coastdown. Then set the
thermostat lower to make the circuit again by observing indicating light. A
timer prevents rapid cycling of the compressor. Count the time from the start
of compressor coastdown to the restart of the compressor. This time must be not
less than the manufacturer's recommended time. Observe the prerotation vane's
position during the period the compressor is off and restart. The vanes should
be fully closed when the compressor is off. They should stay closed before the
compressor reaches full speed, then open to their preset fully opened position.
7.5.2 While the building load is reduced for various stages of part
load tests, observe the running of the compressor. There shall be no excessive
noise and vibration. Special attention should be paid to very low load tests to
Page 56
] :
detect surge. Among other operating parameters, surge depends on the amount of
flowing refrigerant, prerotation vane position, and water temperature. Therefore
observations should be made for all part load conditions specified, since
condenser water temperature specified for part loads may be different. A current
meter shall be used to monitor the current draw of the compressor during load
changes. Marked fluctuation of current draw indicates compressor surge.
7.6 Cooling plant system tests. These tests are basically for
interlocking of cooling plant equipment rather than refrigeration machine itself.
Therefore, these tests much depend on the design of the plant. Project drawings
and specifications must be thoroughly studied.
7.6.1 Test interlocking of plant components. Compressor shall not

start before condenser water and chilled water pumps are started, if they are in
automatic mode.
7.6.2 Test lead-lag control. Verify the positions of lead-lag

switch with the sequencing of refrigeration machine operations.
7.6.3 Test automatic system start control. If the cooling system

is designed for automatic start by sensing outside air temperature or by timer
settings, the sensing bulb of the temperature controller shall be placed in
temperature bath set at the specified temperature or the timer shall be
manipulated to the specified on/off time. The cooling system shall be observed
to act in their correct sequence.
8. Calculations and rate performance.

8.1 Full load test. The full load refrigerating capacity shall be
calculated as follows by using the averaged values of the test data (at least 3)
Qout = w ( c p) (T e ' Ti)
Qm = W (For SI)
Qin = W x 3.413 (For Customary)
where: Q out = cooling capacity, J/s (Btu/h)

w = chilled water mass flow rate, kg/s (lb/h) ,
see
SE-37, 39, 41, or 43, EXHIBIT 2-B.
c
p = specific heat of water, J/(kg °C) [Btu/(lb °F) at
mean temperature of T e and T L
T e = chilled water supply temperature, °C (°F)
Tj^ = chilled water return temperature, °C (°F)
Qin
= power input of machine, J/s (Btu/h)
W = measured watt meter reading
Page 57
8.2 Part load test. Use the same equations as for full load test. All
sets of specified conditions or percent of part load conditions of 7.4 shall be
calculated
8.3 Rate performance.
8.3.1 The full load capacity of the machine must be not less than
the specified full load capacity.
8.3.2 The full load power rate shall not be more than the specified
full load power rate.
8.3.3 The part load power rates must not be more than the specified
rates
8.3.4 The pressure drop of chilled water in evaporator shall not be

more than 2.5 % of that specified.
8.3.5 The pressure drop of condenser water in condenser shall not

be more than 2.5 % of that specified.
Page 58
. .
EXHIBIT 3-D RECIPROCATING REFRIGERATION MACHINE TEST PROCEDURE
1. Scope. The test procedures described in this EXHIBIT apply to packaged

liquid chilling refrigeration machines using electric driven reciprocating
compressors for refrigerant compression to achieve cooling effects. Electric
motors may be open or hermetic types. Condensers may be water cooled or air
cooled
2. Purpose.
2.1 To verify full capacity of the installed refrigeration machine for
meeting the specified capacity without exceeding the specified power input.
2.2 To verify part load power consumption of the machine not exceeding the
specified part load power limits at the specified part loads.



functions
3.1 ARI Standard 590 (Standard for Reciprocating Water- chilling Packages)
prescribes requirements for testing of packaged reciprocating water chillers.
It specifies the basis for testing, rating, and publishing of capacities and
power requirements. These machines are tested and rated at full load under the
following conditions:
Leaving chilled water temperature 6 .

7 °C
(44 °F)
Entering chilled water temperature 12.4 °C (54 °F)
Fouling factor of water side surfaces

non-ferrous tubes 0.000088 m 2 °C/W (0.0005 °F h ft 2 /Btu)
steel tubes 0.000176 m 2 °C/W (0.0010 °F h ft 2 /Btu)
Water cooled units:
Leaving condenser water temperature 35 °c (95 °F)
Page 59
Air cooled and evaporatively cooled units:

Entering air dry bulb temperature 35 °C (95 °F)
Entering air wet bulb temperature (evap cooled only) 23.9 °C (75 °F)
Heat reclaim units:
Entering condenser water temperature (water cooled) 23.9 °C (75 °F)
Entering air dry bulb temperature (air cooled) 4.4 °C (40 °F)
Heat reclaim condenser entering and leaving temperature:
Water cooled -- 40.6 to 48.9 °C (105 to 120 °F) or 35 to 48.9 °C (95 to
105 °F)
Air cooled -- 21.1 to 35 °C (70 to 95 °F)
Package with remote condenser:
Saturated discharge temp (water or evap cooled) 40.6 °C (105 °F)
Liquid refrigerant (water or evap cooled) 35 °C (95 °F)
Saturated discharge temp (air cooled) 48.9 °C (120 °F)
Liquid refrigerant (air cooled) 43.3 °C (110 °F)
Part load test. A minimum of two part load tests are required. Depending on the
unloading steps of the compressor, the part loads and test condition requirements
vary (see paragraph 5.2). The conditions of entering condenser water, air, or
refrigerant are given as:
Condenser inlet conditions = A x B + C
where A and C are constants as listed in table below

B = % full load compressor displacement
A C
Condenser entering air dry bulb, °C (°F) 0.4 55

(air cooled)
Condenser entering air wet bulb, °C (°F) 0.1 65
(evap cooled)
Condenser entering water temperature, °C °F)
(
0.1 75
(water cooled)
Saturated discharge temp of air cooled
with remote condenser, °C (°F) 0.4 80
Saturated discharge temp of water or evap
cooled with remote condenser, °C (°F) 0.1 95
Water flow rate for water cooled units is the same as full load test (i.e.
0.538 L/s per kW (3 gpm/full load ton)). The liquid refrigerant temperature of
remote condensers is 5.6 °C (10 °F) below saturated discharge temperature
calculated above.
Page 60
.
3.2 Among other requirements, ARI Standard 590 requires the following
safety controls:
High refrigerant pressure cutout,

Cooler ambient freeze protection for cooler located outdoors,
Cooler water freeze protection, and
Hermetic compressor motor protection.
3.3 ASHRAE Standard 30 (Methods of Testing Liquid Chilling Packages)

describes methods of testing of liquid chilling refrigeration machines for their
performance ratings. This standard does not specify the test conditions. Power
measurement is for compressor driver and all auxiliaries.
3.4 ASHRAE Standard 15 (Safety Code for Mechanical Refrigeration) covers

a much wider range of requirements than the refrigeration machine itself. Its
purpose is to assure the safe design, construction, installation, operation, and
inspeetion of refrigeration systems.
3.5 ASHARE Standard 90 (Energy Conservation in New Building Design) sets

performance of HVAC equipment. The latest edition should be used for minimum
performance requirements. The energy input to all auxiliary components of the
refrigeration machine is included (consistent to ASHRAE Standard 30
requirements)

EXHIBIT 3-A for inspection).

in calibration (see Chapter 2 for calibration of instruments). Instruments
supplied with the machine may be used to take test data, if they are calibrated
and the accuracies satisfy the minimum tolerance requirements of tests.
4.3 In most cases a false load is needed for full load performance test.
handling systems). The former approach may require temporary equipment to
provide heat source, piping from the heat source to the refrigeration machine or
cross-over between the condenser and the evaporator (for water cooled condenser
units only) and accessories such as shut-off valves and temperature controlling
,
mixing valves. If cross-over of chilled water and condenser water is used, the
Page 61
Team should review the piping layout to be sure that water entering both
evaporator and condenser may be adjusted individually to those of the specified
values. The disadvantage of the latter approach is the long lagging time for the
temperature at the refrigeration machine to stabilize (from the time to
introducing false load at the air handling systems to achieve stable and desired
conditions at the test machine). After it is determined the approach to take
based on cost comparisons, good coordination between all involved parties is
essential.
4.4 The heat exchanger tubes may need to be cleaned to yield the specified
cooling, excessive scale inside the water tubes may have accumulated. This is
especially important for condenser tubes, because of the low quality of the
condenser water and higher temperature of the tube surface. It is difficult to
measure the actual fouling factor or scale thickness in the field. Only actual
cleaning will assure the correct performance of the machine. The Team should
obtain written statement from the contractor or witness the cleaning operation
that the tubes are cleaned according to the manufacturer's recommendations (such
as using chemicals). If the machine has been in operation, the contractor or
manufacturer's representative must make the decision of cleaning tubes, since
chillers with scaled tubes may not pass the power consumption criteria of the
contract specification and the commissioning tests.
5.1 Full load test. The refrigeration machine must deliver the specified
conditions. Project specification usually specifies the entering and the leaving
chilled water temperature, and/or the water flow rates, the maximum water
friction of the heat exchanger (s) the operating conditions of the condenser, and
,
the maximum power consumption rate at these specified conditions. The maximum
water velocity in the heat exchanger tubes may also be specified. Each of these
ratings or limitations must be verified by testing directly or verified by
deducing from test data. Since the capacities of air cooled condensers and
evaporative condensers depend on the conditions of the ambient air, the full load
test may not verify the capacities of the condensers. If the conditions of the
ambient air is not as specified during this test, the full capacity test is for
the packaged units excluding the condensers. The capacities of these condenses
(air cooled or evaporatively cooled) must be tested separately as described in
EXHIBIT 3-F, HEAT REJECTION EQUIPMENT TEST PROCEDURES.
5.2 Part load test. Depending on the refrigeration machine’s part load
performance curve, the energy performance of a machine may vary considerably. In
order to have optimum energy performance for the entire cooling season, more than
one part load conditions may be specified. The chiller performance at these
specified part load shall be tested.
Page 62
.
to reduce its capacity and vice versa. The test should verify the automatic
capacity change following load changes without running into unstable conditions
for the entire range of capacity from full load to minimum load as specified.
Capacity control involves step control of cylinder unloading and/or compressor
sequencing.

to the controls required in ARI Standard 590 (see paragraph 3 of this EXHIBIT,
Industry standards), other safety features are usually specified, such as
refrigerant circuit low pressure cutout, low oil pressure cutout, non-recycling
compressor overload safety, etc. All these safety controls, if specified, should
also be tested.
5.5
plant components, such as sequencing of chillers.
6. Instrumentation. The required measurement, minimum accuracies, and

Temperature.
6.1.1 Chilled water temperature leaving evaporator. The measurement

system error shall not exceed +/- 0.1 °C (0.2 °F) .

two temperature measurements. The measurement error shall not exceed +/- 0.1 °C
(0.2 °F)
6.1.3 Condenser water temperature entering condenser (water cooled).

The measurement error shall not exceed +/- 0.1 °C (0.2 °F) .

condenser water entering and the leaving condenser (water cooled) for the same
reason as given for chilled water measurement. Same accuracy requirement as for
chilled water, +/* 0-1 °C (0.2 °F) .
6.1.5 For air cooled units, measure the dry bulb temperature of air
entering condensing coil. The measurement error shall not exceed +/- 0.3 °C
(0.5 °F) .
Page 63
6.1.6 For evaporatively cooled units, measure the wet bulb

temperature of air entering evaporative cooler. The measurement error shall not
exceed +/- 0.5 °C (1 °F) .
6.1.7 For units with remote condensing units, measure the saturated
discharge temperature of the refrigerant at the refrigeration machine (not at the
condenser end). The measurement error shall not exceed +/- 0.3 °C (0.5 °F)
6.1.8 For units with remote condensing units, measure the liquid
refrigerant temperature of the refrigerant at the refrigeration machine (not at
the condenser end). The measurement error shall not exceed +/- 0.3 °C (0.5 °F) .
6.1.9 The temperature sensor locations for temperature measurements

are important. For water measurement, they should be located to sense well mixed
bulk water temperature. If chilled water or condenser water is used to cool any
component of the refrigeration machine, the temperature sensors must be located
to include the effects of this cooling. For air measurement (dry and wet bulb),
pay attention that the air at the point of measurement is the same that enters
the heat exchangers.

6.2the refrigeration machine for maintenance purposes, such as for bearing,
parts of
oil, refrigerant, etc., shall be calibrated to have errors less than +/-0.6 °C
(1 °F) . They shall not be used for commissioning tests unless they are verified
to meet the minimum accuracy requirements as stated previously.
6.1.11 Temperature sensors and thermometers for water and

refrigerant measurement are usually installed in wells. They may be removed from
equipment and calibrated either in laboratory or in field. Wells should be
refilled with thermal conducting compound when replacing sensors.
Water flow rate.
6.2.1 Chilled water pipe. The total error of combined sensing and
6.2.2 Condenser water pipe. The total error of combined sensing and

of theflow meters are appropriate. The minimum pipe lengths upstream and
2. Avoid areas where water flow may be swirl (e.g. after consecutive elbows).
If space is tight, using of flow s traighteners is very helpful.

Page 64
6.2.5 In majority of installations the water flow rates of

reciprocating refrigeration machines are of fixed values. Without having to
consider flow ranges, the type of flow meters to be used for permanent
installation or just for functional performance tests can be easily selected.
If differential pressure type (orifice plate or venturi, etc.) is used, the
primary element with the largest throat diameter satisfying the required accuracy
should be selected.

6.3.2 The pressure instruments supplied with the machine for

operation and maintenance purposes, such as pressure gages for oil pressure and
refrigerant pressure shall be calibrated in laboratory or in field. When these
instruments are taken off the machine, exercise caution so that the media to be
sensed shall not be in contact with the atmosphere.
6.3.3 For large chillers where maximum pressure drops of water heat
exchangers are specified, pressure gages are usually required and installed at
inlet and outlet of evaporators and condensers. These instruments may be used
to verify the heat exchanger water pressure drops.
6.4.1 Polyphase watt meter or watthour meter. Error shall not

exceed +/- 0.5% of reading.
6.4.2 Measurement of energy shall include that consumed by

compressor and auxiliaries.
6.4.3 Check and record electric voltage between feeders and the

used as guidelines only. Since the testing agent is responsible for performing
guide. However, the intended purposes of these tests must be carried out and
their acceptance criteria must be satisfied.
Page 65
7.1
Safety control and general operational test. This test should be

performed before full and part load tests. Certain simulated inputs may be
needed to trigger control actions. Therefore some tests are limited to checking
safety control circuits instead of creating true cutout situations. Indicating
lights and responses of relays, actuators, and compressors are used to confirm
the control action. Details of control sequence may differ somewhat between
manufacturers and design setup, the Team should be familiar with the wiring
diagrams and manufacturer's instructions. The following tests are general
procedures for confirming control sequencing function.
7.1.1 Make sure area is clear of personnel . - IMPORTANT
7.1.2 Check voltage balance of electric power service. The maximum

voltage deviation from average of three voltage measurements should not be
greater than +/- 1% of the average. In equation form, it is:
(A, B, or C) - (A + B + C) / 3
% voltage imbalance =
(A + B + C) / 3
where A, B, and C are voltage measurements between phases.
7.1.3 Make sure the crankcase heater has been on and is working by
feeling the warmth of the compressor. The heater should be on for at least 24
hours with all valves in the refrigerant lines in open positions.
7.1.4 Check compressor oil level.
7.1.5 With control circuit power connected, test all pilot lights
and alarms by pressing the appropriate buttons (if provided).
7.1.6 (For machines with water cooled condensers) Start condenser

water pump.
7.1.7 (For machines with water cooled condensers) Check condenser

water flow rate. This should be done after cooling tower is readied for
operation. If the flow rate differs substantially from that of the specified
rate, adjust flow balancing device on condenser water line to approximately the
required rate.
7.1.8 (For machines with water cooled condensers) Check temperature

of entering condenser water. The cooling tower temperature control should be
adjusted to provide the specified condenser water temperature.
7.1.9 (For evaporatively cooled machines with remotely evaporative

cooler) Turn on evaporative cooler unless refrigeration machine is interlocked
to start the evaporative cooler automatically.
7.1.10 Start chilled water pump.
Page 66
.
7.1.11 Check and adjust chilled water flow rate to approximately

specified rate.
7.1.12 Check and set chilled water temperature thermostat to supply

the specified chilled water. Machine manufacturer's instruction may be needed
for determining set point (depending on controller throttling range, compressor
configuration, and allowed water temperature rise).
7.1.13 Start machine operation by pushing "on" button.
7.1.14 Confirm compressor starting and energizing of liquid line

solenoid valve after a preset time delay. Compressor should start with only
first step of cylinder loaded.
7.1.15 (For air cooled and evaporately cooled machines) Make sure
rotation direction of fan is correct.

bath to the trip temperature of the control as recommended by the machine
manufacturer. Remove temperature sensor from well and place in temperature bath.
Vary the bath temperature +/- 1.1 °C (2 °F) slowly. By observing pilot light,
measuring electric potential at appropriate wiring junction, or observing other
responses of the machine, the make and break point of the chiller circuits shall
be recorded. Also record the set point of the temperature switch. The tolerance
of the set point and the actual break point shall not exceed 0.6 °C (1 °F) The .
temperature switches to be tested shall include chilled water low temperature

cutout and any other temperature sensing safety devices. For air cooled units
located outdoors, heating cables equipped with thermostats are usually specified
for evaporators in cold climatic regions. It is not practical to expose and test
this heating system due to the thermal insulation covering, unless its
functioning is obviously questionable.
7.1.17 Test flow actuated safety controls. When flow switches in

the chilled and the condenser water lines are specified to stop the compressor
when low or 7.1.18
no flow conditions exist, test these switches by disengaging
interlocking between pump starters and compressor starter and switching off the
respective water pumps or by turning off valves in the chilled and the condenser
water pipes (providing the pipe arrangement permit turning valves off) to the
machine. The compressor should stop to verify the functioning of this safety
control
Test pressure actuated safety controls. Check to be sure

that the refrigerant line to high pressure safety switch and the high pressure
gauge are located on compressor side of discharge service valve. Slowly close
compressor discharge service valve until compressor power is cut. This is the
high pressure cutout and its pressure should be recorded. To restart the
compressor, restore the start circuit (see manufacturer's operation manual) and
reopen the discharge service valve. For compressors equipped with time delay,
the time elapsed between compressor cutout and cutin should be recorded and
Page 67
compared with manufacturer's specifications. The low pressure safety switch is

tested by slowly closing the suction service valve until the compressor is cut
out. Reopening the suction valve should restart the compressor. The cutin and
cutout pressures of the test results shall be compared with the manufacturer's
recommended pressure as listed in the machine manual. The differences of the
actual recorded pressure and recommended pressure shall not exceed the tolerances
given by the machine manufacturer. For multi-compressor machines there may be
more than one high and low pressure switches. Each switch shall be tested.
7.1.19 Check oil level again after machine has been running for at
least 1/2 hour. Oil should have no foam and at correct level. If oil pressure
gage is specified or installed, record pressure.
7.1.20 Check refrigeration level through sight glass for refrigerant

undercharge. There should be no bubbles. Measure and record liquid line
pressure and temperature. Calculate subcooling to verify refrigerant charge.
7.1.21 Load the machine gradually. With constant water flow rate
through the evaporator, the temperature differential of the chilled water
entering and leaving the evaporator and the numbers of active cylinders and
compressors indicates the loading condition of the machine. In most cases false
load will be required.
7.1.21.1 If false load is applied to the building equipment,

overloading of air handling equipment and test refrigeration machine occurs. The
Team should evaluate the natural building load (internal load and weather) at the
time of test to fully utilize these loads so that the amount of false load may
be kept to a minimum.
7.1.21.2 If false load is applied to the temporary heating

equipment and/or crossover piping between the condenser and evaporator (water
cooled machines), heat should be added gradually and cross over valves
manipulated to give the specified temperature differentials of both condenser and
chilled water. The water flow rates of the condenser and evaporator should be
checked frequently to maintain the specified rates.
7.1.23
7.1.22 While load is being increased, observe and record the return
chilled water temperature when the loading of cylinders and compressors occur.
The temperature should agree with the control step settings. Also monitor the
compressor current draw. The maximum current shall not exceed the specified
demand limit.
Check compressor discharge pressure for refrigerant

overcharge. The discharge pressure and the condensing media temperature
relationship should be obtained from the machine manufacturer. However, non-
condensibles, poor heat transfer, improperly adjusted backpressure valve, etc.
may also cause high discharge pressure. Refrigeration overcharge may also
determined by measuring liquid subcooling.
Page 68
. .
7.1.24
(For air cooled and condenserless machines) Test head
pressure control. Head pressure control must maintain minimum head pressure
during low ambient operation. When machine unloads, head pressure tends to drop
presenting opportunity to observe head pressure control. Depending on
manufacturer's preference (air cooled type) and system design (condenserless
type),
there are various ways to control head pressure during low ambient
applications. The Team should be familiar with the submittals for the chiller
installed. The following examples are for machines with simple ambient
temperature and head pressure controls.
7.1.24.1 For ambient temperature control. Place temperature

sensor in liquid temperature bath. Adjust bath temperature to the project
specified or manufacturer's recommended temperature. Observe and confirm
condenser control actions (fan, damper or other action as specified).
7.1.24.2 For head pressure control. By manually blocking

condenser air flow or fan operation, observe and confirm head pressure controller
signals
7.1.25 Test lead- lag compressor control arrangement by manipulating

lead- lag
7.2 switches. Confirm sequencing by observing compressor actions.
7.1.26 Test automatic system start control. If the cooling system

is designed for automatic start by sensing outside air temperature or by timer
settings, the sensing bulb of the temperature controller shall be placed in
temperature bath set at the specified temperature or the timer shall be
manipulated to the specified on/off time. The cooling system shall be observed
to act in their correct sequence. Automatic start/stop controls should not
bypass automatic pumpdown control circuit.
Full load test. This test shall be performed immediately after safety
control and general operational control tests. Test procedures depend on
condenser arrangement. Note that before recording full load data, verify that
hot gas by-pass is off. The manual valve on the hot gas bypass may be turned off
during full load test.
7.2.1 Chiller with water cooled condenser.
7. 2. 1.1 Add false load until the chiller is fully loaded (all
steps of all compressors are loaded)
7. 2. 1.2 Check flow rate of chilled water to specified value.

Adjust balancing device if necessary.
7. 2. 1.3 Adjust chilled water supply and chilled water return

temperature to those of the specified by adjusting chilled water temperature
controller and the amount of false load.
Page 69
7. 2. 1.4 Check flowrate of condenser water to specif led value

Adjust balancing device if necessary. If temporary crossover between chilled and
condenser water pipes are contemplated for adding false load, careful adjustment
of valves may be necessary to obtain the specified flow rates and temperatures
of the chilled and condenser water. If during the time of test the outside air
wet bulb temperature is higher than that of the specified for the cooling tower
and the specified condenser water temperature is not attainable (chances of this
is rare), the test must be postponed until the outside air wet bulb temperature
drops below the specified value of the cooling tower.
After water flow rates and temperature of both

7. 2. 1.5
condenser and evaporator have achieved the specified values, the refrigeration
machine shall run for a minimum of one hours. Data shall be recorded at 10
minute intervals. Minor adjustment of water flow rates and temperature may be
needed during this period. The test setup is considered stabilized and test data
for full load performance may be taken, if 3 sets of data (30 minutes total
time), after any adjustment, are within the tolerances as listed below:
* Water flow rate +/- 5% of specified values;
* Water temperature +/- 0.6 °C (1 °F) of specified values.
7. 2. 1.6 Data shall be taken at 10 minute intervals. A minimum

of three sets of data shall be averaged for capacity and energy calculations.
7. 2. 1.7 Data to be recorded:
* Chilled water leaving temperature.
* Chilled water differential temperature (or chilled water

entering temperature).
* Condenser water entering temperature.
* Condenser water differential temperature (or condenser

water leaving temperature)
* Chilled water flow primary element differential pressure

or other flow instrument output.
* Chilled water entering and leaving pressure (Required only

for large chillers where specifications limit maximum water pressure drops).
* Condenser water flow primary element differential pressure

* Condenser water entering and leaving pressure (Required

only for large chillers where specifications limit maximum water pressure drops)
Page 70
. . 4
6 .
* Total Wattmeter output (For compressor and auxiliaries, but

7.2.2 chilled and condenser water pumps, see paragraph 6.4).
does not include
Chiller with packaged air cooled condenser and remote air

cooled condenser.
1 1.2 Check flow rate of chilled water to specified value.

. 2 .
.2.2.3 Adjust chilled water supply and chilled water return

7
7 .2.2. Measure condenser entering air temperature. In most

cases it is lower than the project specified air temperature. In order to
simulate an operation condition similar to that of the specified, it is necessary
to reduce the condenser air flow rate to increase the saturated discharge
temperature of the refrigerant so that the actual saturated discharge temperature
equals the specified value. Since chillers are always equipped with a pressure
gage or other pressure measurement device at the compressor discharge piping,
this pressure reading may be converted to indicate the saturated discharge
temperature. Depending on the physical arrangement of the condenser coils and
the setup of automatic head pressure controls, various ways may be used to reduce
the condenser air flow rate, thus raise the compressor discharge pressure and
temperature: manually blocking air passage to the condensers, manipulating air
dampers or fan controls
7 .2.2.5 After the chilled water flow rate, the temperature of

the chilled water, and the compressor discharge pressure/temperature have
achieved the specified values, the refrigeration machine shall run for a minimum
of one hours. Data shall be recorded at 10 minute intervals. Minor adjustments
may be needed during this period. The test setup is considered stabilized and
test data for full load performance may be taken, if three sets of data (30
minutes total time), after any adjustment, are within the tolerances as listed
below:
* Water flow rate +/- 5% of specified value;
* Saturated compressor discharge pressure +/- 20.7 kPa (3

psig)
7. 2. 2. Data shall be taken at 10 minute intervals. A minimum

Page 71
7 .2.2.7 Data to be recorded:


* Water pressure at inlet and outlet of evaporator (Required

only for large chillers where specifications limit maximum water pressure drops).
* Condenser air entering temperature.
7.2.3 * Saturated compressor discharge pressure.
* Total Wattmeter output (For compressor and auxiliaries,

including condenser fan motor)
Chiller with evaporative condenser.
7. 2. 3. Check flow rate of chilled water to specified value.

7. 2. 3. Adjust chilled water supply and chilled water return

7. 2. 3. Measure dry bulb and wet bulb temperature of air

entering evaporative condenser. In most cases it is lower than the project
specified air temperature. In order to simulate an operation condition similar
to that of the specified, it is necessary to reduce the condenser air flow rate
and/or the amount of spraying water to increase the saturated discharge
temperature of the refrigerant so that the actual saturated discharge temperature
equals the specified value. Since chillers are always equipped with a pressure
gage or other pressure measurement device at the compressor discharge piping,
this pressure reading may be converted to indicate the saturated discharge
temperature. Depending on the physical arrangement of the evaporative condenser
and the setup of automatic head pressure controls, various ways may be used to
raise the compressor discharge pressure and temperature: manually blocking air
passage to the condensers, manipulating air dampers or fan controls to reduce
condenser air flow, or manipulate valves on the spray piping to reduce the amount
of spray water.
Page 72
. . 5 . .
7. 2. 3. After the chilled water flow rate, the temperature of

the chilled water, and the compressor discharge pressure/temperature have
achieved the specified values, the refrigeration machine shall run for a minimum
of one hours. Data shall be recorded at 10 minute intervals. Minor adjustments
may be needed during this period. The test setup is considered stabilized and
test data for full load performance may be taken, if three sets of data (30
minutes total time), after any adjustment, are within the tolerances as listed
below:
* Water flow rate +/- 5% of specified value;
* Saturated compressor discharge pressure +/- 20.7 kPa (3

psig)
Data shall be taken at 10 minute intervals. A minimum

7. 2. 3. 6
7. 2. 3. 7 Data to be recorded:


* Water pressure at inlet and outlet of evaporator (Required

only for large chillers where specifications limit maximum water pressure drops)
* Dry and wet bulb temperatures of air entering evaporative

condenser
* Saturated compressor discharge pressure.
* Total Wattmeter output (For compressor and auxiliaries,

including fan and pump motor of evaporative condenser)
7.3 Part load tests. Part load tests shall be performed immediately after
the full load test. Unless the part load conditions are specified in the project
specification (in cooling tonnage or percentage of full load), part load tests
shall be performed at two load steps - a step closest to 60% of full load and the
lowest step. If the chiller has only one step of unloading or no capability of
unloading, it shall be tested at 60% and 40% of full capacity. The chilled water
leaving temperature shall be as for full load. The condenser entering conditions
are the same as those of ARI Standard 590 (see paragraph 3.1). They are listed
below for 60%, 50%, and 40% of full load.
Page 73
Part load
60% 50% 40%
Entering cond. w. temp. °C °F) (
(water cooled) 81 80 79
Saturated disch. temp. °C (°F)
(air cooled, evap. cooled) 104 100 96

chilled water return pipe. The new load shall be stabilized at the larger part
load of the two part load described in paragraph 7.3 above.
7.2.2

load tests (paragraphs 7.2.1 for units with water cooled condensers, paragraph
for units with air cooled condensers, and paragraphs 7.2.3 for units with
evaporative condensers), except that water pressure measurements at inlet and
outlet of heat exchangers need not be performed.
7.3.3 Repeat the same procedures for the lower part load tests.
7.3.4 After tests, cut off all false load and restore all valves to
their normal operation modes.

8.1 Full load test.
8.1.1 Full load capacity. The full load refrigerating capacity

shall be calculated as follows by using the averaged values of the test data (at
least 3) :
Qout ~ w ( c p) (Te ll)
Q in = W (For SI)
Qm " W x 3.413 (For Customary)
where: Q out = cooling capacity, J/s (Btu/h)

w *= chilled water mass flow rate, kg/s (lb/h) ,
see
SE-37, 39, 41, or 43, EXHIBIT 2-B.
c p = specific heat of water, J/(kg °C) [Btu/(lb °F) ]
at
mean temperature of Te and T1
T e = chilled water supply temperature, °C (°F)
Ti = chilled water return temperature, °C (°F)
Qin = power input of machine, J/s (Btu/h)
W = measured watt meter reading
Page 74
.
8.2 Part load test. Use the same equations as for full load test. Both
part load conditions of paragraph 7.3 shall be calculated.
8.3.1 The full load capacity of the machine must be not less than
8.3.2 The full load power rate shall not be more than the specified
full load power rate.
8.3.3 The pressure drops of chilled and condenser water in

evaporator and water cooled condenser shall not be higher than those specified.
This requirement applies only to large chillers where maximum water pressure
drops are given in the project specifications.
8.3.4 The part load power rate must not be more than the specified
rates
Page 75
EXHIBIT 3-E ABSORPTION REFRIGERATION MACHINE TEST PROCEDURE
1. Scope. The test procedures described in this EXHIBIT apply to absorption

refrigeration machines using steam or hot water as energy source.
2. Purpose.
2.1 To verify full capacity of the machine for meeting the project
specified capacity without exceeding the specified energy input.
2.2 To verify part load energy input of the machine not exceeding the
specified part load energy limits at the specified part loads.



functions
3 1 . ARI Standard 560 (Standard for Absorption Water- chilling Packages)
prescribes requirements for testing of absorption water chillers. It specifies
the basis for testing, rating, and publishing of capacities and energy
requirements. These machines are tested and rated at full load under the
following conditions:
Leaving chilled water temperature 6.7 °C (44 °F)

Entering chilled water temperature 12.2 °C (54 °F)
Fouling factor of water side surfaces 0.000088 m 2 °C/W
(0.0005 hr ft 2 °F/Btu)
For part load performance, the chilled water temperature, chilled water flow
rate, and condenser water flow rate remain the same as for full load. The
entering condenser water temperature varies linearly with load, decreasing from
29.4 °C (85 °F) for full load to 15.6 °C (60 °F) for no load.
The standard requires that the published capacity be not less than 95% of test
capacity and that the published energy consumption rate and condenser water flow
Page 76
rate be not more than 105% of their corresponding test rates.
3.2
The required safety controls include low temperature cutout and provisions for
interlocking to stop operation of the chiller if chilled water flow fails.
ASHARE Standard 90 (Energy Conservation in New Building Design) sets

performance of HVAC equipment. The latest edition should be used for the mimimum
performance requirements.

EXHIBIT 3 * A for inspection).

supplied with the machine may be used to take test data, if they are calibrated
and the accuracies satisfy the minimum tolerance requirements of tests.
4.3 In most cases a false load is needed for full load performance test.
handling systems) The former approach may require temporary equipment to
.
provide heat source, piping from the heat source to the refrigeration machine or
cross-over between the condenser and the evaporator, and accessories such as
shut-off valves and temperature controlling mixing valves. If cross-over of
chilled water and condenser water is used, the Team should review the piping
layout to be sure that water entering both evaporator and condenser may be
adjusted individually to those of the specified values. The disadvantage of the
latter approach is the long lagging time for the temperature at the refrigeration
machine to stabilize (from the time to introducing false load at the air handling
systems to achieve stable and desired conditions at the test machine) After it
.
is determined the approach to take based on cost comparisons, good coordination

between all involved parties is essential.
4.4 The heat exchanger tubes may need to be cleaned to yield the specified
cooling, excessive scale inside the water tubes may have accumulated. This is
especially important for condenser and absorber tubes, because of the low quality
of the condenser water and high temperature of the tube surface. It is difficult
to measure the actual fouling factor or scale thickness in the field. Only
Page 77
actual cleaning will assure the correct performance of the machine. The Team
should obtain written statement from the contractor or witness the cleaning
operation that the tubes are cleaned according to the manufacturer's
recommendations (such as using chemicals). If the machine has been in operation,
the contractor or manufacturer's representative must make the decision of
cleaning tubes, since chillers with scaled tubes may not pass the thermal
performance
5.1 criteria of the contract specification and the commissioning tests.
Full load test. The refrigeration machine must deliver the specified
conditions. Project specification usually specifies the entering and the leaving
chilled water and condenser temperatures, and/or the water flow rates, the
maximum water friction of the heat exchanger(s) ,
and the maximum energy
consumption rate at these specified conditions. The maximum water velocity in
the heat exchanger tubes may also be specified. Each of these ratings or
limitations must be proven by testing directly or proven by deducing from test
data
5.2 Part load test. Some project specifications may also specify part
load performance (capacities vs. energy consumption rates) for optimum energy
performance. The operating conditions of the condenser water temperature are
usually different from that of the full load. The chiller performance at part
load shall be tested at the specified part load conditions.
by reducing its capacity and vice versa. The test should verify the automatic
capacity change following load changes without running into undesirable
conditions for the entire range of capacity from full load to minimum load as
specified

to the controls required in ARI Standard 560 (see paragraph 3 of this EXHIBIT,
Industry standards), other safety and operation features provided by the chiller
manufacturer (such as non-condensable purging equipment) should be tested.

plant components, such as sequencing of chillers.
Page 78
.
6. Instrumentation.
6.1 The required measurement, minimum accuracies, and
Temperature.
6.1.1 Chilled water temperature leaving evaporator . The measurement

system error shall not exceed +/- 0.1 °C (0.2 °F) .

two temperature measurements. The measurement error shall not exceed +/- 0 1 °C .
(0.2 °F) If separate measurement of entering evaporator is desired, total

.
measurement error for chilled water entering evaporator shall not exceed 0.1 °C
(0.2 °F)
6.1.3 Condenser water temperature entering absorber. The


condenser water entering absorber and leaving condenser. Similar to chilled
water temperature measurement, the accuracy shall be +/- 0.1 °C (0.2 °F) If .
condenser water leaving condenser is measured, the measurement error shall not
exceed +/- 0-1 °C (0.2 °F) .
6.1.5 Hot water measurement (for hot water operated chiller). Same
as for chilled water measurement.
6.1.6 Steam and condensate measurement (for steam operated chiller).

The measurement error shall not exceed +/- 0.6 °C (1 °F) The steam temperature
.
measurement is for checking the state of steam. The temperature sensing location
should be close to the steam control valves. The condensate temperature sensing
location should be in the condensate drop leg before steam traps.
6.1.7 The temperature sensor locations for temperature measurements

are important. They should be located to sense well mixed bulk water
temperature. If chilled water or condenser water is used to cool any component
of the refrigeration machine, the temperature sensors must be located to include
the effects of this cooling.

parts of the refrigeration machine for maintenance purposes, shall be calibrated
to have errors less than +/- 0.6 °C (1 °F) They shall not be used for full and
.
part load tests unless they are verified to meet the minimum accuracy
requirements as stated previously.
Page 79
6.1.9 Temperature sensors and thermometers for water measurement are

usually installed in wells. They may be removed from equipment and calibrated
either in laboratory or in field. If the sensing elements are removed, wells
must be refilled with thermal conducting compound when replacing the elements.
6.2 Water and steam flow rates.
6.2.1 The flow rates of chilled water, condenser water, hot water
and steam shall all be measured. The total error of combined sensing and readout
devices shall not exceed +/- 3% of measured quantity.

of the flow meters are appropriate. The minimum pipe lengths upstream and
2. Avoid areas where fluid flow may be swirl (e.g. after consecutive elbows).
If space is tight, using of flow straighteners is very helpful.

6.2.4 In majority of installations the flow rates of chilled and

condenser water are of fixed values. Without having to consider flow ranges, the
type of flow meters to be used for permanent installation or just for
commissioning tests can be easily selected. If differential pressure type
(orifice plate or venturi, etc.) is used, the primary element with the largest
throat diameter satisfying the required accuracy should be selected.

6.3.2 Steam pressure measurement at chiller inlet. Instrument error

shall not exceed 689 Pa (0.1 psig)
6.3.3 Pressure gages are usually specified and installed at inlet

and outlet of heat exchangers. These instruments may be used to verify the heat
exchanger water pressure drops.
6.3.4 The pressure instruments supplied with the machine or

installed by construction contractor for operation and maintenance purposes shall
be calibrated in laboratory or in field. When these instruments are taken off
the machine, exercise caution so that the media to be sensed shall not be in
contact with the atmosphere.
Page 80
. !
6.4.1 Watt meter or watthour meter shall be used for chiller

electrical power measurement. Error shall not exceed +/- 0.5% of reading.
6.4.2 Check and record electric voltage between feeders and the

used as guidelines only. Since the testing agent is responsible for performing
guide. However, the intended purposes of these tests must be carried out and
their acceptance criteria must be satisfied.
7.1 General operational test. This test should be performed before full
and part load tests. Certain simulated inputs may be needed to trigger control
actions. Therefore some tests are limited to checking safety control circuits
instead of creating true cutout situations. Indicating lights and responses of
relays, actuators, and other equipment are used to confirm the control action.
Details of control sequence may differ between manufacturers and design setup.
The Team should be familiar with the wiring diagrams and manufacturer's
instructions. The following tests are general procedures for confirming control
sequencing function.
7.1.1 Make sure area is clear of personnel .

- IMPORTANT
7.1.2 Make sure all temperature sensors and controllers have been
calibrated and functioning properly. These include chilled water supply
controller for controlling steam or hot water valves and condenser water
temperature controller for cooling tower and/or condenser water by-pass valve.
Be sure controllers are set at the project specified temperatures.

bath to the trip temperature of the control as recommended by the machine
manufacturer. Remove low temperature cutout sensor from well and place in
temperature bath. Vary the bath temperature +/- 1.1 °C (2 °F) slowly. By
observing pilot light and measuring electric potential at appropriate wiring
junction, the make and break point of the chiller circuits shall be recorded.
Also record the set point of the temperature switch. The tolerance of the set
point and the actual break point shall not exceed 0.6 °C (1 °F) If the chiller
.
is provided with other safety temperature switches, they shall be tested

similarly
Page 81
7.1.4
Make sure chilled water pump, condenser water pump, and
cooling tower interlocking is functioning properly. Cooling tower should be
readied for operation.
7.1.5 Test flow actuated safety controls. When flow switches in the
chilled water (required by ARI Standard 560) and the condenser water lines are
specified to stop the chiller operation when low or no flow conditions exist,
test these switches by disengaging interlocking between water pump starters and
switching off the respective water pumps or by turning off valves in the chilled
and the condenser water pipes (providing the pipe arrangement permit turning
valves off) to the chiller. Their operation may be verified by observing pilot
lights, measuring electric potential at appropriate wiring junctions or operation
of chiller pumps.
7.1.6 All pilot lights should be checked for proper indication.
7.1.7 Check chilled water and condenser water flow rates. They
shall agree with project specified rates. Adjust flow balancing devices if
necessary 7.1.9
7.1.8 Chiller is started in accordance to manufacturer's

instructions
The testing agent (manufacturer's representative or other

qualified personnel see project specifications) shall load the machine gradually
,
until it is fully loaded. With constant water flow rate through the evaporator,
the temperature differential of the chilled water entering and leaving the
evaporator indicates the loading condition of the machine. In most cases false
load will be required.
7. 1.9.1 If false load is applied to the building equipment,

overloading of air handling equipment and test refrigeration machine occurs. The
Team should evaluate the natural building load (internal load and weather) at the
time of test to fully utilize these loads so that the amount of false load may
be kept to a minimum.
7.1.10
7. 1.9. 2 If false load is applied to the temporary heating
equipment and/or crossover piping between the condenser water and chilled water,
heat should be added gradually and cross over valves manipulated to give the
specified temperature differentials of chilled water. The water flow rates of
the condenser and evaporator should be checked frequently to maintain the
specified rates.
After chiller is fully loaded and operating in stable

conditions, withdraw solution samples from generator and absorber with flasks.
These samples shall be dried in oven to determine their salt concentration. The
concentration shall agree with the manufacturer's recommendations. It is usually
the responsibility of the manufacturer's representative to adjust chiller to its
Page 82
. . ,
most efficient operating conditions.
7.1.11 Operate purge system for at least one hour to remove

non- condensables .Take factory recommended procedures to demonstrate that the
chiller is free of non-condensables. Also check non-condensables at purge system
discharge to be hydrogen free.
7.1.12 Due to the high temperature of the condenser water in the

condenser, the condenser tube fouling should be checked. Determine the
condensing temperature of the refrigerant by using a refrigerant
pressure - temperature chart (also known as lithium bromide equilibrium chart) and
7.2
by knowing the concentration of solution withdrawn from concentrator and the
solution temperature leaving concentrator. The difference between the
temperature of concentrated solution leaving concentrator and the vapor
condensing temperature at full load shall not exceed the manufacturer's
specifications
Full load thermal performance test. This test shall be performed

immediately after general operational tests.
7.2.1 Check flow rate of chilled water to specified value. Adjust

balancing device if necessary.
7.2.2 Adjust chilled water supply and chilled water return

7.2.3 Check flow rate of condenser water to specified value. Adjust

balancing device if necessary.
7.2.4 Adjust condenser water temperature controls and/or cooling

tower temperature controls to obtain the specified condenser water temperature
(at entering absorber) . The purpose of this step is to simulate the effect of
design weather. If temporary crossover between chilled and condenser water pipes
7.2.5
are used for adding false load, careful adjustment of valves may be necessary to
obtain the specified flow rates and temperatures of the chilled water. If during
the time of test the outside air wet bulb temperature is higher than that of the
specified value for the cooling tower and the specified condenser temperature is
not attainable (chances of this is rare) the test must be postponed until the
outside air wet bulb temperature drops below the specified value of the cooling
tower
After water flow rates and temperature of both condenser and

evaporator have achieved the specified values, the refrigeration machine shall
run for a minimum of one hours. Data shall be recorded at 10 minute intervals.
Minor adjustment of water flow rates and temperature may be needed during this
period. The test setup is considered stabilized and test data for full load
performance may be taken, if three sets of data (30 minutes total time), after
any adjustment, are within the tolerances as listed below:
Page 83
7. 2. 5.1 Water flow rate +/- 5% of specified values;
7. 2. 5. Water temperature +/- 0.6 °C (1 °F) of specified

values
7.2.6 Data shall be taken at 10 minute intervals. A minimum of

three sets of data shall be averaged for capacity and energy calculations.
7.2.7 Data to be recorded:
7. 2. 7.1 Chilled water leaving temperature.
1 2 1.2 Chilled water differential temperature (or chilled

. .
water entering temperature).
7.2.7 .3 Condenser water entering temperature.
7 .2.7 .4 Condenser water differential temperature (or condenser

water leaving temperature)
1 2 1 .5 Chilled water
. . flow primary element differential
7 .2.7 .6 Chilled water entering pressure.
1 . 2 . 1 .1 Chilled water leaving pressure.
7. 2. 7. Condenser water flow primary element differential

7.2.7.10
7. 2. 7. Water pressure of condenser water when entering
absorber
Water pressure of condenser water when leaving

condenser
7.2.7.11 Watthour reading for electric consumption.
For hot water operated chiller:
7.2.7.12 Hot water entering temperature.
7.2.7.13 Hot water differential temperature (or hot water

entering temperature)
7.2.7.14 Hot water flow primary element differential pressure

7.2.7.15 Hot water entering pressure.
Page 84
7.2.7.16 Hot water leaving pressure.
For steam operated chiller:
7.2.7.17 Steam temperature before control valve.
7.2.7.18 Steam pressure before control valve. - IMPORTANT.
7.3
7.2.7.19 Steam flow primary element differential pressure or
other flow instrument output.
7.2.7.20 Condensate temperature.
Part load tests. If part load thermal performance tests are required
in the project specification, part load tests shall be performed immediately
after the full load test. The amount of chiller loads, chilled water
temperature, and condenser water temperature shall be adjusted in accordance to
those specified.

chilled water return pipe. The new load shall be stabilized at the largest part
load of the part loads specified. The leaving chilled water temperature and the
condenser water temperature entering absorber shall be as specified for the part
load.

load tests (paragraphs 7.2), except that the water pressure measurements for
chilled, condenser, and hot water need not be performed.
7.3.3 Repeat the same procedures for the next larger part load
specified until all specified part loads have been tested.
7.3.4 After tests, remove all false load and restore all valves to
their normal operation modes.
Page 85
8.1
8.1.1load test.
Full
Full load capacity. The full load refrigerating capacity

shall be calculated as follows by using the averaged values of the test data (at
least 3) :
Qout = W1 ( c pl) (Tel Tu )
Qine = W (For SI)
Qine = W x 3.413 (For Customary)
For hot water operated chiller:
Qinh “ w2 ( c p2 ) (T e 2 * T 12 )
For steam operated chiller:
Qinh = w2 ( H2 * c p2 x T 12 )
where
c pi = specific heat of chilled water, J/(kg °C) [Btu/(lb °F) ]
at mean temperature of T el and T u

Cp 2 = specific heat of hot water, J/(kg °C) [Btu/(lb °F)
at mean temperature of T e2 and T 12
H = enthalpy of steam, J/kg (Btu/lb)
Qine
= electric energy input to chiller, J/s (Btu/h)
Qinh
= hot water or steam energy input of chiller, J/s (Btu/h)
Qout
= cooling capacity, J/s (Btu/h)
Te i = chilled water entering temperature, °C (°F)
T e2 = hot water entering temperature, °C (°F)
Tn = chilled water leaving temperature, °C (°F)
T 12 = hot water leaving temperature, or condensate
temperature, °C (°F)
W = measured watt meter reading.
8.3.1 w : = chilled water mass flow rate, kg/s (lb/h), see SE-37,
39, 41, or 43, EXHIBIT 2-B.
Wo = Hot water mass flow rate, kg/h (lb/h), see SE-37, 39,
41, or 43, EXHIBIT 2-B.
8.2 Part load test. Use the same equations as for full load test.
The full load capacity of the machine must be not less than
Page 86
8.3.2 The heating energy consumption rate at full and part loads
shall not be more than those specified.
8.3.3 The chiller coefficient of performance at full load shall not

be less than that specified. The COP is calculated as:
Qout
cop
Qine + Qinh
8.3.4 The pressure drop of chilled water in evaporator shall not be

more than that specified.
8.3.5 The combined pressure drop of condenser water in absorber and

condenser shall not be more than that specified.
8.3.6 The pressure drop of hot water in generator shall not be more
than that specified.
Page 87
EXHIBIT 3-F HEAT REJECTION EQUIPMENT TEST PROCEDURES
1. Scope and general.
1.1 The procedures described in this EXHIBIT apply to testing of heat

rejection equipment for refrigeration machines, including factory and field
assembled cooling towers, evaporative condensers, and dry coil refrigerant
condensers
1.2 Since the performance of heat rejection equipment depends on the

conditions of outside air, it is difficult to test these equipment in the field
under exactly the specified conditions. The method of testing of cooling towers
and evaporative condensers used in this EXHIBIT is to test these equipment under
weather conditions at the time of testing, with certain limitations, and compare
test results with the manufacturer supplied test data curves or tables.
1.3 For air cooled condensing coils, the condensing coil capacity is
closely proportional to the temperature difference of condensing temperature and
air dry bulb temperature. Therefore, the coil capacity tested at a certain
outdoor temperature may be converted to design conditions if the condensing
temperature and outside air temperature are known. The test procedures in this
EXHIBIT is based on this assumption.
1.4 In order to test the performance of air cooled condensers and

evaporative condensers accurately, the flow rate of the refrigerant must be
measured. However, the installation of additional flanges, valves, flow meters,
etc. to facilitate flow rate measurement increases the possibility of refrigerant
loss. Therefore, it is a decision of the designers and specifiers whether
accurate capacity test is required during the functional tests. The test
procedure outlined in this guide assumes that accurate capacity measurements are
required
2. Purpose.
2.1 To verify thermal performance of heat rejection without exceeding

specified power input.

functions
2.3 To verify safe operation of the equipment.
Page 88
2
3.1
3.1.1 tower.
Cooling
ASME Standard PTC-23 ( Test Code for Atmospheric Water-Cooling

Equipment) provides methods and procedures for testing overall performance of
atmospheric cooling 1.1.1
towers. This code does not set a definite set of test
conditions. In stead, it gives limitations of test conditions referencing to
tower design conditions. Among these limitations are:
3. Wet-bulb temperature of air not more than 1.7 °C (3

°F) above or 3.9 °C (7 °F) below design wet-bulb temperature. Air temperature
may be measured at tower air intake or windward side (relative to tower) of
atmospheric air
3. 1.1. 2 Circulating water flow not more than +/- 10% of design
circulating water flow.
3. 1.1. 3 Range (water in temperature minus water out

temperature) not more than +/- 20% of design.
3.1.2
3. 1.1.4 Heat load not more than +/- 20% of design.
Manufacturer's performance curves within these limitations are used to compare

the test results and tower performance.
3.2
CTI Bulletin ATC-105 (Acceptance Test Code for Water Cooling
Towers) is very similar to the ASME test code. The major differences are:
3. 1.2.1 Wet -bulb temperature of air not more than +/- 5.6 °C
3.2.1 Air temperature is measured at tower air intake.
(10 °F) of design.
3. 1.2. As an alternative to using performance curves for

comparing test results, this code allows using characteristic curves for
estimating thermal performance of the tower at specified conditions.
Air cooled refrigerant condenser.
ARI Standard 460 (Remote Mechanical draft air- Cooled

Refrigerant Condensers) prescribes testing and rating requirements for remote
air-cooled condensers. The standard rating conditions are, among others:
3. 2. 1.1 35 °C (95 °F) entering air dry-bulb temperature;
3. 2. 1.2 51.7 °C (125 °F) refrigerant condensing temperature;
3. 2. 1.3 87.8 °C (190 °F) entering (condenser) refrigerant

vapor temperature.
Page 89
Degree of refrigerant subcooling is not specified. The condensing coil has no

3.2.2pressure ( no external ductwork)
external static
ASHRAE Standard 20 (Methods of Testing for Rating Remote

Mechanical -Draft Air-Cooled Refrigerant Condensers) describes test methods and
procedures for remote air-cooled condensers. It does not specify test
conditions. Methods of measuring refrigerant flow are made by using either
calorimeter or orifice plate.
3.3.1
3.3 Evaporative refrigerant condenser.
ASHRAE Standard 64 (Methods of Testing Remote Mechanical -Draft

Evaporative Refrigerant Condensers). The testing method is quite similar to that
for air cooled condensers. The standard does not specify test conditions,
therefore it does not give criteria for comparing with specified thermal
performance

4.1 It is assumed that, before the scheduled test, the construction
contractor or manufacturer's representative has prepared the heat rejection
equipment in accordance to the recommendations of the manufacturer for startup
and operation and an inspection of the equipment and condenser water system, if
applicable, has taken place (see EXHIBIT 3-B for inspection).

supplied with the equipment may be used to take test data after they have been
calibrated and the accuracies satisfy the minimum tolerance requirements of the
tests
4.3 The heat rejection equipment tests should precede or follow

immediately the refrigeration machine tests. Certain measurements and procedures
for refrigeration machine may be used or modified for heat rejection equipment
test. Examples are condenser water flow rate measurement, application of false
load to test equipment, or condenser water temperature measurement in some
installations
4.4 Cooling tower.
4.4.1 Condensing water system must be balanced in accordance to

project specifications. If multi- tower are installed, condenser water flow rates
to individual towers must be balanced correctly.
4.4.2 Water distribution valves at tower inlet, if installed, must

be balanced.
Page 90
.
4.4.3 Tower static head (discharge to distribution plate or through

nozzles) must be adjusted to specified value.
4.4.4 Water level in the water basin is as recommended by the

manufacturer and is stable.
4.4.5 Water is free from debris. Check and clean sump and screen
(or strainer) for debris.
4.4.6 Measure wet-bulb temperature at air intake of tower. It must

be within +/- 5.6 °C (10 °F) of specified wet-bulb temperature. If wet-bulb
temperature of air is beyond these limitations, the test must be postponed until
a more appropriate weather.
4.4.7 Check wind velocity where air circulation is not influenced

by tower air (or when tower fan is off) The wind velocity shall not be over 268
.
km/s (10 mph) during the test.
4.4.8 Disable basin temperature control if basin temperature control

is specified and provided (i.e. the tower has no automatic temperature control
on condenser water temperature).
4.5 Air cooled condenser.
4.5.1 The outdoor temperature during the test must be above 26.7 °C
(80 °F)
4.5.2 Disable discharge pressure control during test.
4.5.3 It is assumed that the project specification has specified and

the construction contractor has installed pressure gages at coil inlet and
outlet, and valved branch pipes with orifice plate at coil inlet (check project
specifications for detailed requirements).
4.6 Evaporative condenser.
4.6.1 Make sure spray water is clean and free of debris.
4.6.2 Make sure water level in water basin is as recommended by the

equipment manufacturer, the bleed line is balanced, and the makeup valve is
working properly.
4.6.3 Measure wet-bulb temperature around air intake. It must be

within +/- 5.6 °C (10 °F) of specified wet-bulb temperature. If wet-bulb
temperature of air is beyond these limitations, the test must be postponed until
a more appropriate weather.
4.6.4 If the condenser is located outdoors, check wind velocity. The

wind velocity shall not be over 268 m/s (10 mph) during the test.
Page 91
5. Instrumentation.
5.1 Cooling tower.
5.1.1 Condenser water entering temperature (hot water). The

measurement system error shall not exceed +/- 0.1 °C (0.2 °F) For multi-tower
.
or multi-cell installation, a preferred measurement location is at the main

condenser pipe before any branching. Location of leaving condenser water
measurement for chiller test may be used if the distance between the tower and
the chiller is less than 15.2 m (50 ft).
5.1.2 Condenser water entering (hot water) and leaving (cold water)
temperature differential measurement. Direct measurement of temperature
differential is preferred than measuring both entering and leaving temperatures
and deducing the difference. The measurement error shall not exceed +/- 0,1 °C
(0.2 °F) If differential temperature measurement is difficult to obtain, the
.
leaving condenser water temperature should be measured and the measurement error
of this measurement shall not exceed +/- 0.1 °C (0.2 °F) For multi-tower or
.
multi-cell installations, special attention should be given so that the sensor

or sensors of the water leaving towers measure the truly mixed water temperature
and has minimum influence from pumping and piping heat gains. A good compromise
is at the condenser water pump discharge pipe if the pump is within 15 2 m (50 .
ft) of the tower.
5.1.3 Condenser water flow rate. The measurement system error shall
not exceed +/- 3% of measured quantity. Pitot traverse shall be used for
determining water velocity. The instruments for condenser flow rate measurement
in chiller tests may be used for cooling tower tests.
5.1.4 Wet-bulb temperature of air entering cooling tower. The

measurement error shall not exceed +/- 0.6 °C (1 °F) Measurements shall be
.
taken in inlet air stream, at 1.2 m (4 ft) from the tower and 1.5 m (5 ft) above
water basin. A minimum of three wet-bulb temperature measurements at different
locations (same level) shall be averaged for thermal performance comparisons.
5.1.5 Fan power. Watt meter of watthour meter. Error shall not
exceed +/- 0.5% of reading.
5.2 Air cooled condenser and evaporative condenser.
5.2.1 Refrigerant temperature at condenser inlet and outlet. The

measurement error shall not exceed +/- 0.3 °C (0.5 °F) If no thermometer wells
.
are provided, attach temperature sensors on the outside of refrigerant pipe and
cover sensor and pipe with 0.025 m (1 in.) thick mineral wool thermal insulation
at least 0.3 m (1 ft) long.
5.2.2 Refrigerant pressure at condenser inlet and outlet. The

measurement error shall not exceed +/- 6.89 kPa (1 psig) (see project
specification)
Page 92
. 2 .
5.2.3 Refrigerant flow rate. Measure at condenser outlet with

variable area flow meter or turbine flow meter. The measurement error shall not
exceed +/- 1% of reading (see project specification).
5.2.4 Fan power rate. Watt meter or watthour meter. Measurement

error shall not exceed 0.5% of reading.
5.2.5 Dry bulb temperature of air +/- 0.6 °C (1 °F) .
5.2.6 For evaporative condenser only:
5. 2. 6.1 Wet bulb temperature of air. Measurement error shall

not exceed +/- 0.6 °C (1 °F) .
6.1
5. 2. 6. Water circulating pump power rate. Watt meter or
watthour meter. Error shall not exceed +/- 0.5% of reading.
6. Test procedures.
Cooling tower.
6.1.1 Load refrigeration machine to specified full capacity.

Chilled water and condenser water temperature are measured at 10 minute
intervals. The system is considered stabilized if 3 sets of data 10 minutes
apart (30 minutes total) are within the tolerances as described in chiller test
procedures (see Appendices 3-C, 3-D, and 3-E)
6.1.2 Turn off makeup and bleed valves.
6.1.3 Measure condenser water flow rate.
6.1.4 Measure temperature of condenser water entering and leaving

cooling tower and/or condenser water temperature differential.
6.1.5 Measure entering air wet bulb temperature.
6.1.6 Measure fan power rate.
6.1.7 All measurements shall be repeated every 10 minutes for a

total test run time of one hour (6 sets of data) All data shall be averaged for
.
capacity calculations. The tolerances of measured data shall be as listed below.

If any data variation is greater than listed, the test is invalidated and new
test must be performed.
6. 1.7.1 Water flow rates +/- 5% of specified values.
6. 1.7. Condenser water (entering and leaving tower) +/- (0.3

°C (0.5 °F)
Page 93
1.1
6. 1.7. Entering air wet bulb temperature variation rate +/-
°C/h (2 °F/h)
6.2
6. 1.7. Tower heat load +/- 5%.
Air cooled condenser and evaporative condenser.
6.2.1 Check head pressure control following procedures outlined in

paragraph 7.1 of EXHIBIT 3-D.
6.2.2 Manipulate liquid line bypass valves directing refrigerant

going through flow measuring device during test (see project specifications for
piping and valve arrangement)
6.2.3 Measure condensing coil entering air temperature. This

temperature shall be above 26.7 °C (80 °F) .
6.2.5
6.2.4 The refrigeration machine shall be fully loaded. For loading
procedures and system stabilization requirements, see paragraph 7.2 of EXHIBIT
3-D.
Data shall be taken at 10 minute intervals for a total test

time of one hour (6 sets). Required data and their tolerances are as follows:
6. 2. 5.1 Entering air dry bulb temperature.
6. 2. 5. Refrigerant temperature at condenser inlet and outlet.

The tolerance of temperature difference between this temperature and entering air
dry bulb shall not be over +/- 0.1 °C (1 °F) .
6. 2. 5. Refrigerant pressure at condenser inlet and outlet.
6. 2. 5. Liquid refrigerant flow rate.
6. 2. 5. Fan power rate.
6. 2. 5. For evaporative condenser only:
* Wet bulb temperature around intake air.
* Circulation pump power rate.
Page 94
7. Calculations and comparison of performance.

7.1 Cooling tower.
7.1.1 Temperature range = T in - T out
7.1.2 Temperature approach *= T out - Twb
where T in -= condenser water entering cooling tower (hot

water) ,
average of readings
T out = condenser water leaving cooling tower (cold
water) ,
average of readings
T wb = entering air wet bulb temperature, average of
readings
7.1.3 Performance criteria. The cooling tower performance from the

measured values are compared with manufacturer supplied performance curves. With
the same air wet bulb temperature and cooling range of the test conditions and
the manufacturer's performance curve:
7.1.4 the tested approach shall be not less than the approach of the
manufacturer's curve; and
7.1.5 The measured fan power rating shall not be more than the
specified rating.
7.2 Air cooled refrigerant condenser.
7.2.1 Find enthalpy of refrigerant at condenser inlet by locating

one set of inlet pressure and temperature on a pressure -enthalpy diagram (ASHRAE
1985 Handbook). If absolute pressure is needed, covert gage pressure to absolute
pressure by
P abs = Pgage + 101-3 kPa (all units in kPa) (For SI)
P abs = Pgage + 14.696 psi (all units in psi) (For Customary)
7.2.2 Check refrigerant condition at condenser outlet by using

outlet pressure and temperature. The refrigerant must be at subcooled
conditions. If the refrigerant condition is not subcooled and the corresponding
outside air dry bulb temperature is below the specified value, the condenser is
undersized and should be rejected.
7.2.3 Similar to paragraph 7.2.1, find enthalpy of refrigerant at

condenser outlet.
7.2.4 Adjust refrigerant flow rate if required (see EXHIBIT 2-B for
flow rate calculations and adjustments).
Page 95
7.2.5 Calculate condenser heat rejection rate.
Q - M (H in - H out )
where H in = enthalpy of refrigerant at condenser inlet as

calculated in 7.2.2, J/kg (Btu/lb)
H ou t “ enthalpy of refrigerant at condenser outlet
as calculated in 7.2.3, J/kg (Btu/lb)
M - Refrigerant mass flow rate as calculated in 7.2.4,
kg/h (lb/h)
Q = Condenser heat rejection rate, J/h (Btu/h)
7.2.6 Average the 6 heat rejection rates, Q avg . This is the

condenser capacity at the test conditions.
7.2.7 Convert condenser heat rejection capacity at test conditions

to that of the design conditions.
(Tcond) spec - (T db ) spec

(Q) spec ( Q ) avg X
C^cond) test * (T d b)test
where (Q) spec calculated coil capacity at specified conditions,

*=
J/h (Btu/hr)
(Q)avg = tested coil capacity (see 7.2.6 above), J/h (Btu/h)
(Tcond ) spec = condensing temperature from specifications,
°C (°F)
( CO nd ) test
= saturation temperature corresponding to tested
discharge pressure, °C (°F)
(Tdb) spec = air dry bulb temperature from specifications, °C
(°F)
(o
(Tdb ) test = air dry bulb temperature from test, °C F)
7.2.8 The heat rejection rate (Q) spe c shall not be less than 95% of
the specified heat rejection capacity.
7.2.9 Calculate the average of the 6 measured fan power rates. The
averaged power rate shall not be more than the specified power rate.
7.3 Evaporative condenser.
7.3.1 Find enthalpy of refrigerant at condenser inlet by locating

one set of inlet pressure and temperature on a pressure-enthalpy diagram (ASHRAE
1985 Handbook). If absolute pressure is needed, covert gage pressure to absolute
pressure by
Pabs = Pgage + 101.3 kPa (all units in kPa) (For SI)
Pabs = Pgage + 14.696 psi (all units in psi) (For Customary)
Page 96
. 3
2
7.3.2 Check refrigerant condition at condenser outlet by using

outlet pressure and temperature. The refrigerant must be at subcooled
conditions. If the refrigerant condition is not subcooled and the corresponding
outside air wet bulb temperature is below the specified value, the condenser is
undersized and shall be rejected.
7.3.3 Similar to 7.3.1, find enthalpy of refrigerant at condenser

outlet
7.3.4 Adjust refrigerant flow rate if required (see EXHIBIT 2-B for
flow rate calculations and adjustments).
7.3.5 Calculate condenser heat rejection rate.
Q = M (H in - H out )
where H in «= enthalpy of refrigerant at condenser inlet as

calculated in 7.2.2, J/kg (Btu/lb)
H out = enthalpy of refrigerant at condenser outlet
as calculated in 7.2.3, J/kg (Btu/lb)
M = Refrigerant mass flow rate as calculated in 7.2.4,
kg/h ( lb/h)
Q = Condenser heat rejection rate, J/h (Btu/h)
7.3.6 Average the 6 heat rejection rates, Q avg •

This is the
evaporative condenser capacity at the test conditions.
7.3.7 Performance criteria.
7. 3. 7.1 The total heat rejection rate Q avg shall not be less
than that shown on the manufacturer supplied curve or table at the same entering
air wet bulb and saturated condensing temperature.
7. 3. 7. The average measured power rating of fan shall not be

more than the specified rating.
7. 3. 7. The average measured power rating of the circulation

pump shall not be more than the specified rating.
Page 97
. . . . .
CHAPTER A HEATING PLANT
CHAPTER 4 HEATING PLANT
1. Scope. This chapter provides inspection and testing procedures for heating
equipment and systems. Heating equipment included in this chapter are packaged
air-heating furnaces, hot-water boilers and steam boilers. Boilers may be
cast-iron sectional, fire-box or Scotch-marine fire- tube type, or water-tube
type. Steam boilers may be low pressure (103.4 kPa (15 psig) ASME Boiler and ,
Pressure Vessel section IV) or medium pressure (up to 1034 kPa (150 psig), ASME
Boiler and Pressure Vessel section I). Fuels for furnaces and boilers may be
natural gas, oil, or electric.
a. ASME Boiler and Pressure Vessel Code - Section I (for power boilers, to
operate over 103.4 kPa (15 psig) steam pressure, or over 121 °C/1103 kPa (250 °F
/160 psig) hot water) Section VI (for heating boilers, to operate not over 103.4
;
kPa (15 psig) steam, or not over 121 °C/1103 kPa (250 °F/160 psig) hot water).
b. ASME PTC 4.1 - Steam Generating Units.
c. ASHRAE Standard 103 - Methods of Testing for Heating Seasonal Efficiency

of Central Furnaces and Boilers.
d. The Hydronic Institute - Testing and Rating Standard for Heating

Boilers
e. AGA Standard - Standard for Gas-Fired Low-Pressure Steam and Hot-Water

Boilers
f. NFPA Standard 31 - Standard for the Installation of Oil Burning

Equipment
g. NFPA Standard 54 - National Gas Fuel Code.
h. NFPA Standard 85A - Standard for Prevention of Furnace Explosions in

Fuel Oil- and Natural Gas-Fired Single Burner Boiler- Furnaces
i. NFPA Standard 85B - Standard for Prevention of Furnace Explosions in

Natural Gas-Fired Multiple Burner Boiler- Furnaces
j NFPA Standard 85D - Standard for Prevention of Furnace Explosions in

.
Fuel Oil-Fired Multiple Burner Boiler- Furnaces
Page 99
3. Heating System Inspection. Boilers, furnaces, and their components

shall be inspected for construction and installation to meet safety and
functional requirements. See EXHIBIT 4-A for inspection procedures. See Appendix
for inspection check lists.
4. Heating System Testing.

4.1 Boilers shall be tested in the field to meet the capacity and
efficiency requirements of the contract specification. See EXHIBIT 4-B for test
procedures. See Appendix for test work sheets.
4.2 Furnaces shall be tested in the field to meet the efficiency

requirements of the contract specification. See EXHIBIT 4-C for test procedures.
See Appendix for test work sheets.
4.3 Boilers, furnaces, and their components shall be tested for functional
operations. Burners, automatic safety and capacity controls, oil preheat systems
and other components must perform as prescribed in the contract specifications.
4.4 If the building load at the time of testing does not meet the
specified capacity of the contract specification, means to dispose the heat
generated by the test shall be provided. For hot water boilers, temporary pipe
connections to load sources or building equipment cooling sources may be used.
For steam boilers, applying temporary condensers to absorb discharged steam,
using building equipment cooling sources, or wasting steam to the atmosphere may
be used to accommodate the test. However, the test shall not cause excessively
uncomfortable conditions in the building.
4.5 Operation of boilers must be preceded by heating system cleaning,

boiler boil-off, and appropriate water treatment so that the heating system and
boilers are protected from being contaminated.
4.6 The contract specification may allow manufacturer's factory testing

in lieu of field testing. Factory testing must be witnessed by a commissioning
team representative. The test intentions, test procedures, and acceptance
criteria of this guide must be followed.
Page 100
.
EXHIBIT 4 -A INSPECTION PROCEDURES FOR BOILERS AND FURNACES
1. Scope. The inspection procedures described in this EXHIBIT apply to

packaged and field erected boilers and packaged forced-air heating furnaces.
Boilers included are cast-iron, fire box, scotch marine, electric, and packaged
water- tube boilers used for hot water or steam generation for HVAC systems.
Energy sources for these equipment are gas, oil, or electric.
a. ASME Boiler and Pressure Vessel Code specifies the requirements of
construction and inspection of boilers. Section I of the Code is for power
boilers and Section VI is for heating boilers. Heating boiler is defined as low
pressure boiler having a maximum working pressure of 103.4 kPa (15 psig) for
steam operation or a maximum working temperature of 121 °C (250 °F) and/or
maximum working pressure of 1103 kPa (160 psig) for hot water operation. Power
boiler is defined as medium and high pressure boiler having working pressure or
temperature above those defined for low pressure boiler.
b. NFPA Standard 31 (Standard for the Installation of Oil Burning

Equipment) prescribes requirements for safety in the installation of oil burners
and their associated equipment used in steam, hot water, and hot air heating
plants. Included are chimneys and connectors, oil storage tanks, piping, pumps,
pipe fittings and accessories, and burner controls.
c. NFPA Standard 54 (National Fuel Gas Code) is a safety code which applies
to the installation, inspection and testing of fuel gas systems, equipment using
fuel gas and related accessories.
d. NFPA Standard 85A (Standard for Prevention of Furnace Explosions in Fuel

Oil-and Natural Gas-Fired Single Burner Boiler-Furnaces) establishes standards
for design, installation, operation and maintenance of single burner oil- and
gas-fired boilers to contribute to safety and prevention of furnace explosions.
Boiler sizes are limited to fuel input greater than 3663 kW (12.5 x 10 6 Btu/h)
Burners included are those firing natural gas only, No. 2, 4, 5, or 6 fuel oil
only, simultaneous firing of gas and oil for fuel transfer, and simultaneous
firing of gas and oil continuously. Emphasis is on operating and maintenance
procedures, combustion control equipment, safety interlocks, alarms, trips and
other related controls of boiler operation.
e. NFPA Standard 85B (Standard for Prevention of Furnace Explosions in

Natural Gas-Fired Multiple Burner Boiler-Furnace) is similar to Standard 85A in
its scope and purpose except that this Standard is for natural gas fired boilers
only and that the number of burners are more than one. Multiple burners cause
Page 101
certain safety requirements to differ from those for single burner boilers. They
are used mostly in field erected large boilers and their application for HVAC use
are not common.
f .NFPA Standard 85D (Standard for Prevention of Furnace Explosions in Fuel

Oil-Fired Multiple Burner Boiler-Furnaces) is similar to Standard 85A in its
scope and purpose, except that this Standard is for oil fired boilers only and
that the number of burners are more than one. The description in paragraph e.
above on gas-fired multiple burners also apply to these boilers.
3. General inspection.
3.1 Review equipment manufacturer's instructions on start-up and operation
procedures
3.2Give complete inspection of boiler, furnace, burner, control system,

oil preheating system, and their associated equipment, including base, vibration
eliminating units associated electrical equipment, piping, ductwork, smoke stack
,
and breeching etc. Be sure that no mis-adjustments damage or rusting occurred.

, ,
All fastenings such as nuts, bolts, and setscrews should be inspected.
3.3 Check equipment name plates to verify equipment model and serial
number. They must have the same model numbers as approved submittals.
3.4 Check for headrooms and access spaces around boiler and furnace for
operation and maintenance. Design specification and manufacturer's recommended
spaces must be provided. For boilers, pay special attention to heat exchanger
tube replacement and cleaning spaces and access spaces to manholes and handholes.
For furnaces, make sure air filter replacement space and burner service space are
adequate
3.5 Inspect heating plant (boiler room and furnace room) for possible fire
hazards. The heating plant should be kept free of combustible fibers and dusts,
flammable liquids, or contents susceptible to smoke or fume contamination.
3.6 Inspect heating plant ventilation openings. Check actual installation

with project drawings and specifications. There shall not be blockage to
combustion air inlets. If automatic dampers are specified and installed, test
damper operator to be sure that dampers open before automatic burners are allowed
to operate
3.7 Verify installed pipe fittings and accessary equipment against project
drawings and equipment manufacturer's recommendations for completeness and proper
installation. Piping includes blow down piping, steam piping, feed water piping,
gas piping (main fuel and pilot systems), and oil piping (include oil preheat
system for heavy oils). Fittings and accessories include but not limit to
valves, strainers, vibration elimination units, thermometer wells, piping
supports, steam traps, etc.
Page 102
.

building structure without undue stress on equipment (boiler, furnace, pump,
etc.). Pay special attention to boiler safety relief valve pipes.
3.9 Make sure all gas vent pipes are terminated outdoors.
3.11 Check alignment of motor driven equipment. Using some simple tools
such as straight edges, square edges, plumb lines, and strings yield good
results. Also observe shaft and coupling for misalignment while machine is
running.
3.12 Observe belt tightness of belt driven equipment. Use belt tension
gage if needed. Belt tension should be as recommended by belt manufacturer.
3.13 Make sure required lubrication is complete (fan, motor, etc.).

must be met.
3.15 Verify installed wiring against project drawings and manufacturer's

submittals
3.17 Check safety control wiring connections. All safety control switches
(switches respond to temperature, pressure, flow, level, etc. to break the safety
control circuit) should be connected in the ungrounded conductor.
3.19 Test run motors (fan, pump, air compressor, etc.) to check correct
direction of rotation.
3.20 Check thermal insulation for damages and omissions. All joints
should be sealed. The material, thickness, and finish should be as specified.
Page 103
3.23 Inspections pertaining to boiler only:
3.23.1 Check water flow direction marks for check valves and flow
switches
3.23.2 All controls containing mercury switches should be checked

for proper leveling.
3.23.3 If pneumatic pressure is used for boiler system controls,

check control air system pressure level.
3.23.4 Inspect boiler refractory for integrate and dryness. There

should be no cracks, chips, and damages. The application of refractory should
be neat and plumb.
3.23.5 After boiler has been in full load operation, inspect

exterior paint for discoloration spots. Discoloration spots are indications of
inappropriate application of refractory material.
3.23.6 Induced draft fans must be insulated as specified.
3.23.7 make sure piping system has been cleaned before connections
to boiler are made.
3.23.8 Make sure boiler is cleaned by flushing with water and

boilout process is performed. Be sure boilout process is performed by the
contractor or manufacturer's representative in according to manufacturer's
recommendations
3.23.9 Perform hydrostatic test to the pressure requirements of the

specification. Secure Certificate of Inspection from boiler inspector. Safety
valves must be removed or protected during hydrostatic test.
3.23.10 For cast iron sectional boilers during hydrostatic test, pay
special attention to sealed joints, possible cracks, and defective castings which
may develop leaks.
3.23.11 Make sure water treatment requirements and blowdown are

maintained during operation for inspection and tests.
3.23.12 For motor starter equipped with overcurrent heaters, check

heater sizes against starter manufacturer's recommendations. The recommendations
are usually contained in operator's manual or posted in starter cabinet.
3.23.13 No leakage should be noted for water, oil, and steam.
Page 104
.
3.24 Inspection pertaining to air-heating furnace only:
3.24.1 Inspect furnace duct connections for excessive air leakage.
3.24.2 Inspect furnace air filters for proper installation and

cleanliness.
3.24.3 Make sure that flexible connections are installed between

furnace and duct system.
4. Boiler burner safety control inspection and tests. Burner

sequence of operations may vary between manufacturers, boiler types, heating
media, pressure levels, sizes, etc. They are all designed for safe operation of
boilers and are generally following certain safety codes. The Commissioning Team
should be familiar with the manufacturer's operation manual before inspection.
The following procedures are presented for general use:
4.1 Inspect oil nozzles, ignitors, electrodes, and other burner

components
4.2 Inspect fuel-air ratio controller, linkages, mechanical fastenings and

stops for tightness and movement.
4.3 Make sure gas and oil line strainers are cleaned. Observe oil line
pressure gage for erratic movement.
4.4 Before operate burners, make sure all valves and switches are in their
operation positions.
4.5 Check pilot flame while draft fan is at maximum and main burner is
off. The pilot should be stable. When burner switch is opened, the pilot flame
should extinguish promptly. Lingering flame require checking of pilot gas valve.
4.6 Verify combustion air interlock with fuel safety valve and electric
ignition. If boiler is equipped with air flow interlock, open air flow switch
to verify control. If boiler is equipped with air pressure (some boilers have
air pump and draft fan from the same motor and is provided with atomizing air
proving switch) and damper sensing interlock, stop fan and manipulate damper
position sensor to verify control. Whenever combustion air control is
interrupted, the fuel safety valve and ignition must deactivate automatically.
4.7 Verify temperature interlock switches by adjusting up (for high

temperature) or down (for low temperature) the temperature settings. The load
contacts and indicating lights (if specified and installed) should act
accordingly. This should be tested and recorded for both cut-in and cut-out
positions. If calibration inaccuracies are suspected for the temperature
Page 105
switches, the sensing elements of the switches should be placed in temperature

bath and calibrated about their recommended set points. Low temperature
interlock switches are usually required in oil preheating systems for heavy
heating oil boilers. High temperature interlock switches are required in hot
water boilers to prevent water temperature exceeding high limits. On a 206.9 kPa
(30 psi) hot water boiler the cut-out temperature should not exceed 116 °C (240
°F) .
4.8 Verify pressure interlock switches by adjusting pressure settings up

or down similar to temperature switches described above. In addition, reduce the
pressure source (air, gas, or oil) for low pressure switches to test their
responses. Low pressure interlock switches are usually required in oil supply
pipes and in atomizing medium (air or steam) pipes for oil-fired burners, in gas
supply pipes for gas -fired burners, and in combustion air streams to prove draft
fan operation. High pressure interlock switches are required in gas pipes for
gas -fired burners and in steam boilers to prevent steam pressure exceeding high
limits. Some oil burners sense the differential pressure between atomizing
medium (air or steam) and oil pressure to interlock main fuel line and ignition.
This safety should be checked for its functioning by creating unfavorable
differential pressure.
4.9 Verify automatic gas safety shutoff valve (gas fired and gas/oil fired
boilers) tightness by the following procedures:
4.9.1 Connect a short flexible tubing to leakage test connection tap

(located downstream of automatic safety shutoff valve between the shutoff valve
and a manual gas cock) and immerse the free end of the tubing in a water cup.
4.9.2 Trip the automatic shutoff valve by removing its energy source
(electricity or air pressure). The valve indicator should now agree with the
valve status.
4.9.3 Close the gas cock downstream of the automatic shutoff valve.
Open the pipe cock on the leakage test tap.
4.9.4 There should be no bubble observed from the flexible tubing

in the water cup.
4.9.5 When the gas pipe is newly installed and is not thoroughly
cleaned, the automatic shutoff valve may indicate leakage. The entire piping and
valves must be cleaned and the test repeated till the valves close tight.
4.10 Test time delays and minimum or maximum time periods of safety
actions by measuring actual time and compare with specified or regulation
required time. Examples are:
4.10.1 When energy source (electricity or air pressure) is removed

from automatic safety shutoff valve, it must close within a specified time.
Page 106
4.10.2 Flame sensing relay must respond to flame failure within a

specified time to trigger alarm and/or indicating light. It must also initiate
control action for combustion safeguard sequences.
4.10.3 Purge timer must prevent safety shutoff valve from opening
before the end of boiler purge cycle.
4.11 While the burner is on, remove the energy source (electricity or air
pressure) of the automatic fuel safety valve. The fire must be out completely
within specified or regulation required time. Also observe valve position
indicator. The indicator must agree with the valve status.
4.12 While the burner is on, close the manual burner valve. The automatic
safety shutoff valve must closed automatically within its specified or regulation
required time.
4.13 Check low fire lighting-off. After pre-ignition purge and before
ignition cycle, the fuel and combustion air control should be interlocked in the
low fire lighting-off position.
4.14 For boilers with automatic cycling controls, check pilot flame
detection controls. The main fuel shut-off valve must be closed when the pilot
flame is not proven.
4.15 For larger sectional boilers with gas burners, there may be multiport
main burners with multi-pilot igniters. Check electronic or thermal supervised
pilot during light-off. Failure of any pilot should cause shut off of fuel to
the pilots and main burners.
4.16 Check indicating lights during the entire inspection and test period
to be sure that they agree with the burner control operation. Indicating lights
are usually provided for:
a. Flame failure
b . Load demand
c. Fuel valve open
d. Low water
e. Draft fan.
4.17 If any lockout fails, it must be corrected and test repeated.
Page 107
5. Boiler capacity control.

5.1 Be sure boiler water circulation is at the contract specified or
manufacturer recommended minimum rate.
5.2 Be sure the oil preheating system is working properly and stable. The
oil temperature supplied to the boiler should be as recommended by the
manufacturer
5.3 After boiler has been operating for a sufficient time to assure warm
conditions, check fuel and air modulating controls for proper settings. The fuel
air ratio at various load conditions should be maintained automatically in
optimum ranges.
5.3.1 The optimum fuel-air ratio may best be checked by flue gas
analysis. An Orsat apparatus may be used for flue gas analysis (see EXHIBIT 2-A
for description of Orsat apparatus) with combustion product drawn from test
opening in stack.
5.3.2 The proper amount of carbon dioxide in the combustion air for
optimum combustion depends on the kind of fuel used. 9.5% to 10.5% for natural
gas and 12.5% to 13% for fuel oil are considered reasonable. There should never
be carbon monoxide measured in the flue gas.
5.3.3 The flue gas should be analyzed at various firing conditions

of the boiler. If the results of combustion analysis is not satisfactory, the
contractor or manufacturer's representative must readjust the settings (gas/oil
pressure, gas valve, capacity controls, capacity sensing, etc., depending on the
make of burner controls) and the test repeated.
6. Boiler safety relief valve inspection and test.

6.1 Inspect safety relief valve installations and obvious damages. The
valves must not show leakage. The discharge pipes must not be supported on the
valves to cause strains on the valves.
6.2 Check installed pipe sizes against project drawings. If the drawings
do not show relief pipe sizes, make sure the inside diameter of the discharge
pipe is equal to or larger than the safety valve outlet diameter. If manifold
discharge pipes are used, the manifold inside area must be equal to or larger
than the combined areas of individual pipes. Valves should be installed on
boilers directly without other fittings between boilers and safety valves.
6.3 Remove safety valves during boiler cleaning and boiloff operations to
protect from damaging to valve internal parts.
6.4 Note valve settings. These valves are factory set and sealed and
should not be altered in the field.
Page 108
.
6.5 Field testing of safety valves. Although safety valves are tested and
adjusted in factory, they should be tested on boiler to be sure no damage
occurred during storage, installation, or boiler hydrostatic testing. Testing
should be done by the valve manufacturer's representative or by boiler inspector.
Testing may be performed in one of the following two methods:
6.5.1 Raise boiler pressure by increasing operating pressure or by

applying hydrostatic pressure to boiler (using hand pump) to the safety valve
pressure setting. The valve should open.
6.5.2 While boiler is under pressure (hydrostatic pressure or

operating pressure which is known by observing pressure gage), use a hand pump
and hydraulic piston to lift the valve spindle until the valve is unseated.
Using the boiler pressure, hand hydrostatic pressure, and the valve seat area,
the valve relieve pressure may be calculated.
7. Boiler water level, makeup water control and low water cutoff.
7.1 Make sure water level control and low water cutoff is mounted in a
plumb position.
7.2 Remove electric control box cover and inspect wiring connections,
terminals and mercury switches for looseness and damages.
7.3 Test makeup water control and low water cutoff to be sure the required
control actions are performed at the correct water levels.
7.3.1 The test should be done while burner is in low fire operation.
7.3.2 By observing glass gauge level, the make up water cut-in and
cut-out levels may be tested by draining boiler water through drain valve or
blowdown valves
7.3.3 When makeup water line is valved off or makeup water pump
disabled and the boiler is slowly drained, the point of fuel cutoff may be
observed. At the moment of fuel cutoff alarm should sound and warning light
activated. In no case should the water level drops below the lowest point of the
water level gauge or the lowest permissible water level. For boilers equipped
with dual low-water protection, each device should be tested independently. If
the lowest allowable water level is reached and the burner is not cutoff
automatically, the drain or blowdown valves should be closed immediately and the
normal water level restored to avoid damage to the boiler.
7.3.4 For electric boilers, be sure the electric power is cutoff

before water level drops below electric heating element.
Page 109
7.3.5
Caution should be exercised during this test. The boiler
drain and blowdown valves should always be attended so that they may be closed
immediately when needed.
7.4 Inspect water gauge glass for cracks and leakage at gaskets. The
gauge glass should be clean. Operate gauge column isolation valves and drain
valves to make sure they function properly. After test, be sure the isolation
valves are left open.
7.5 Check try-cock operations by opening and closing cocks. Compare

try-cock indicated water level with that shown in gauge glass.
8. Other boiler inspection and tests:

8.1 Boiler blowdown.
8.1.1 Test manual blowdown operation by opening and closing blowdown

valves. Blowdown valves shall not leak and blowdown pipe should be terminated
as indicated in project drawings.
8.1.2 Check continuous blowdown valve for appropriate setting.
8.2 Soot blower. Oil-fired or gas/oil-fired steam water-tube boilers

should be tested to assure soot blower operation.
8.2.1 Perform this test only when the boiler is operating close to
full firing. Soot blowing operation during low firing may produce unfavorable
conditions that could interrupt combustion.
8.2.2 Open drain valve to drain accumulated water.
8.2.3 Crack open steam valve to warm pipe up and close drain valve.
8.2.4 Adjust steam pressure to the manufacturer recommended

pressure
8.2.5 Operate soot blower as recommended by manufacturer.
8.2.6 Close steam valve and open drain valve.
8.2.7 Note any abnormal conditions.
8.3 Oil preheating system inspection (for No. 4, 5, and 6 oil).
8.3.1 Check piping and component requirements according to contract

specifications and submittals.
Page 110
.
8.3.2 Test electric oil heater thermostat cutin and cutout points
by immerse its sensing element in liquid temperature bath.
8.3.3 Test hot water or steam oil heater thermostat cutin and cutout
points by immerse its sensing element in liquid temperature bath.
8.3.4 Check electric heater capacity by observing oil temperature

gage during startup period.
8.3.5 Test overall hot water or steam oil heater operation by

observing oil temperature gage, hot water circulating pump, and steam valve
actions. At any firing rate up to burner full fire, the oil temperature and
pressure shall be maintained as required. The fuel oil relief valve should
release excess oil to oil return line during low firing period.
8.3.6 The steam trap and condensate pipe of the steam oil heater
must not be unduly hot.
8.4 Boiler breeching.
8.4.1 Check breeching for correct pitch, as specified.
8.4.2 Check cleanout doors for location, size, latching, and

tightness when closed.
8.4.3 Check expansion joints for tightness.
8.4.4 Check joint of breeching entering masonry chimney for

tightness
8.4.5 Check insulation thickness and integrate.
8.4.6 Make sure test hole is provided at correct locations.
8.5 Boiler automatic recording and control instrumentation.
8.5.1 Make sure automatic recording and control instruments are as

specified in contract documents and submittals.
8.5.2 Demonstrate correct calibration of all instruments. These

usually include temperature (water, air, flue, etc.), pressure (steam, oil, gas,
air, etc.), flue gas and other instruments as the contract specified..
8.5.3 Observe any incorrect ranges, settings, and general operations

of automatic recording and control instruments.
Page 111
9. Air-heating furnace tests.

9.1 Activate furnace heating operation by raising control thermostat
setting and observe operations of components (burner, air circulation fan,
combustion air fan, ignition system, vent damper, etc.). The entire on-cycle
operation should be as required in project specifications and described in
manufacturer's manuals. If system is equipped with thermostat having switches
for cooling-heating and fan on/off, place switches at different combination of
locations and observe furnace operation.
9.2 Check thermostat for correct leveling, if mercury bulb is used for
electrical contacts.
9.3 Check operation of limit switch. Disconnect one leg of electric

wiring at fan control switch. Insert a thermometer with sensing element at the
vicinity of limit switch sensor. The activate furnace control. Observe burner
operation. Burner should stop c sration (firing) at the limit control
temperature. If the bonnet temperature reaches 150 F, or reaches manufacturer's
recommended limit, and firing is not stopped automatically, the limit control is
defective and furnace operation must be manually stopped by turning off switch
on burner control wiring. Restore fan wiring and thermostat setting after test.
Page 112
EXHIBIT 4-B TEST PROCEDURES FOR BOILERS
1. Scope. The test procedures in this EXHIBIT apply to boilers used for HVAC
systems. Included are cast-iron, fire box, scotch marine, electric, and packaged
water tube boilers used for hot water or steam generation. Tests to confirm
capacity and energy conversion efficiency are covered in this EXHIBIT.
Functional tests of boilers and their auxiliaries may be found in EXHIBIT 4-A,
INSPECTION PROCEDURES FOR BOILERS.
a. ASHRAE Standard 103 (Methods of Testing for Heating Seasonal Efficiency

of Central Furnaces and Boilers) provides procedures for determining heating
seasonal efficiency of residential central furnaces and boilers using gas, oil
or electric for fuel. It gives cyclic and part load testing method, test data
manipulation, and calculation of seasonal performance.
b. ANSI Standard Z21.13 (AGA Standard for Gas-Fired Low-Pressure Steam and
Hot-Water Boilers) covers construction and performance requirements of gas-fired
steam or hot water boilers. This standard is applicable to low pressure boilers
as defined in Section VI of ASME Boiler and Pressure Vessel Code and is limited
to boilers of less than 3663 kW (12,500,000 Btu/h) input.
c. ASME Performance Test Code 4.1 (Steam Generating Unit) describes

procedures for conducting performance tests to determine efficiency, capacity and
other related characteristics of steam boilers.
d. The Hydronic Institute Testing and Rating Standard for Heating Boilers
specify methods and procedures for determining performance of cast iron, steel
and copper heating boilers (ASME Section IV boilers) .This Standard gives test
procedures and requirements for overall efficiency and combustion efficiency of
boilers with 87.9 kW (300,000 Btu/h) and larger input. For boilers having less
than 87.9 kW (300 Btu/h) input, the Standard use DOE test requirements.
e. See EXHIBIT 4-A INSPECTION PROCEDURES FOR BOILERS for other standards.
3. General.
3.1 All boilers shall be tested for output at full capacity to verify
capacity requirement, except for small boilers. See contract specifications for
clarification.
3.2 All boilers shall be tested for thermal efficiency at full load. Gas
Page 113
and oil fired boilers shall also be tested for combustion efficiencies at part
loads. Two ways are generally used to test boiler thermal efficiencies for gas
and oil fired boilers. They are tested by input/output method or by heat loss
method. Since this guide requires testing of output at full capacity,
input/output method shall be used for full capacity thermal efficiency tests.
3.3 Contract specifications usually specify the amount of energy input (in
terms of fossil fuel amount or electric input amount) and the amount of energy
output and its conditions, all at peak load. It may also specify the required
efficiencies at different loads. Unless the specification requires otherwise,
the following tests and verifications of the boiler performance shall be
performed during commissioning.
3.3.1 For gas and oil fired boilers, test boiler combustion
efficiencies at 25%, 50%, and 75% of specified capacity. At full load, test
thermal efficiency by using input/output method. For boilers having on-off type
burner controls, efficiencies shall be tested for full capacity only.
3.3.2 For gas and oil fired boilers, test and prove that the
limitation of unburned combustibles is met. The amount of unburned combustibles
allowed may be found in the contract specifications.
3.3.3 For electric boilers, efficiency test by input/output method

is required for full load only.
3.4 The input/output method measures heat in fuel consumed and the heat
output of the boiler. Boiler efficiency is calculated by:
output
Efficiency (per cent) x 100
input
3.5 Flue losses account for the biggest part of gas and oil fired boiler
losses. Combustion efficiency is derived from flue losses. Major effort of
commissioning test should be on measuring flue losses.
3.6 Loss of unburned combustibles is minimized by gas and oil burner

tuning. The contract specification gives the limitations of the amount of
unburned combustibles, therefore, the commissioning team should confirm that the
amount of unburned combustibles in the flue gas is below what is specified.
3.7 Since many of the steps of the boiler test procedure coincide with
boiler tuneup and startup procedures which are usually performed by a factory
personnel of the boiler manufacturers, the same factory personnel may be the Test
Agent
Page 114
.
4. Preparation for tests.

4.1 Before the scheduled performance tests, the project contractor or
manufacturer's representative has prepared the boiler in according to the
recommendations of the manufacturer. The breeching and chimney should be cleaned.
4.2 Make sure that the boiler has been cleaned. Oil, grease, and foreign
matter must be chemically cleaned and flushed. Water treatment specialist should
be consulted as to the cleaning compounds and application procedures for cleaning
boiler and treatment of feed water (For requirement of water treatment, consult
contract specification) . In most cases the building piping system is connected
to the boiler to be commissioned. The entire system shall be cleaned. Safety
relief valves must be protected during cleaning.
4.3 Make sure that boiler and auxiliaries (burners, pumps, fans, etc.) are
adjusted for operation.
4.4 Make sure that boiler has been boiled out. Water treatment specialist
should be consulted for selection of chemical compounds and boil-out procedures.
Safety relief valves must be protected.
4.5 Most boiler inspection items should be performed and requirement

satisfied before performance tests are attempted. See EXHIBIT 4-A for inspection
requirements
4.6 Final adjustments by construction contractor or manufacturer's

representative must be performed before commencing performance tests.
4.7 For boilers requiring preheating of heavy oil, the oil preheat system
must be in normal operating conditions before tests.
4.8 During capacity and efficiency tests (see Paragraph 6. below), the
heating energy produced by the boiler must be absorbed by building air handling
and/or other equipment such as temporary heat exchangers or steam condensers with
cooling medium provided from building cooling system or temporary cooling
equipment. These building equipment should be prepared and ready for operation
before boiler tests. Steam boilers may be arranged to waste steam to the
atmosphere if the steam produced can be safely piped to outside the heating
plant. The construction contractor should have complete plan and preparation for
this exercise. Overheating of building occupied spaces should be avoided.
Page 115
5. Instrumentation.
5.1 Make sure that all instrumentation are in good working orders and are
in calibration. See Chapter 2 BASIC MEASUREMENT for calibration of instruments.
5.2 Instruments required by the contract specification and/or installed

by the contractor or boiler manufacturer may be used for performance tests, if
they meet the accuracy and calibration requirements of this guide.
5.3 The required measurement, minimum accuracies, and measurement

precautions of instruments are given below:
5.3.1 Temperature.
5. 3. 1.1 Flue temperature. The total measurement system error

shall not exceed +/- 2.8 °C (5 °F) Most temperature measurement instruments
.
suitable for the temperature range of up to 538 °C (1000 °F) may satisfy this
requirement. The selection of instruments depends mainly on how practical they
can be used in the field for the size of the boiler.
5. 3. 1.2 Combustion air temperature. The total measurement

error shall not exceed +/- 0.6 °C(1 °F) .
5. 3. 1.3 Steam temperature and feed water temperature. The

total measurement error shall not exceed +/- 0.6 °C (1 °F) .
5. 3. 1.4 Hot water (for hot water boiler) inlet and outlet
temperature. The total measurement error shall not exceed +/- 0.3 °C (0.5 °F) .
A single measurement of temperature differential (water outlet temperature minus

water inlet temperature) is preferred than measuring individual inlet and outlet
temperatures. The total measurement error for differential temperature
measurement shall not exceed +/- 0.3 °C (0.5 °F) .
5.3.2 Flue gas concentration measurement. Orsat apparatus may be

used to measure carbon dioxide, oxygen, and carbon monoxide from the same gas
sample. Portable oxygen, carbon dioxide, or carbon monoxide monitors may be used
to measure individual gas components in the flue gas.
5. 3. 2.1 Orset apparatus. See EXHIBIT 2 -A COMMONLY USED FIELD

TEST INSTRUMENTS. Be certain that the person conducting flue gas measurement
with Orsat apparatus is experienced in its use and the chemical reagents are
fresh.
5. 3. 2. Oxygen monitor, The total measurement error shall not

exceed +/- 0.1 percentage points
Page 116
. 4
2
5
3 .
CHAPTER < HEATING PLANT
5. 3. 2. 3 Carbon dioxide monitor. The total measurement error

shall not exceed +/- 0.1 percentage points.
5. 3. 2. Carbon monoxide monitor. The total measurement error

5. 3. 2. Gas concentration monitors must be calibrated with

standard gas with concentration close to that of the flue gas.
3.3.3 Gas flow rate measurement. Use calibrated gas flow meter.
There may be gas flow meters installed by the gas company. Check if the meter
is dedicated for the boiler to be tested. If not, gas use to other boiler of
appliances need to be turned off during this test. Measurement error shall not
exceed 1% of flow.
5.3.4 Oil flow rate measurement. Use positive displacement meter

(see EXHIBIT 2-A COMMONLY USED FIELD TEST INSTRUMENTS). The meter must be
calibrated for the kind of oil and the temperature at the measuring location.
Depending on the piping arrangement of the burner (with or without oil return,
oil heating equipment location in relationship to the burner, etc.), the location
of the meter should be closely examined so that the exact amount of oil consumed
by the burner may be recorded. The measurement error shall not exceed 1%.
5.3.5 Steam flow rate and hot water flow rate. The total
measurement error shall not exceed +/- 3%. It is important to check the primary
element location for good data. If pipe length does not meet those given in
Chapter 2, flow straightener should be used.
5.3.6 Feed water flow to steam boilers may be intermittent. A

positive displacement meter with flow readout should be used. The measurement
error shall not exceed +/- 1%.
5.3.7 Electric usage for heating element of electric boiler shall

be measured by Watt-hour meter with total measurement error not to exceed 0.5%.
5.3.8 Pressure.
5. 3. 8.1 Gas pressure for gas-fired boiler at a location where

the gas flow rate is measured. The measurement error shall not exceed +/- 50 Pa
(0.2 in. of water)
5. 3. 8. Steam pressure for steam boiler. Measurement error

shall not exceed +/- 0.5% of reading.
5. 3. 8. Barometric pressure. Measurement error not to exceed

+/- 338 Pa (0.1 in of Hg)
Page 117
5. 3. 8. Pressure at flue pipe. Measurement error not to

exceed 12.4 Pa (0.05 in. of water).
6.1
6. Test Procedures, (see Section 3. for required tests)
Gas and oil-fired boilers.
6.1.1 The tests to confirm the boiler capacity and thermal

efficiency are essentially steady state tests at various loads.
6.1.2 After the boiler has been warmed up, the boiler capacity shall
be adjusted to 25% of the full load capacity as required in the contract
specification and the burner capacity control shall be set to manual. The
measurement of load level is done by measuring fuel input flow rate and the
heating value of the fuel or by measuring the output rate of the boiler
(Measuring output at 25% capacity is for hot water boiler only. Measuring steam
output at this low capacity is generally not advisable) The actual running
.
capacity shall be within +/- 3% of the calculated capacity (full capacity input
or output as specified times 25%).
6.1.3 The building air handling and/or other cooling equipment may
need to be adjusted during the test to provide steady and approximately correct
load.
6.1.4 Test data shall be taken after boiler has been running at
steady state conditions for at least 30 minutes. Steady state conditions of the
boiler operation is defined by measuring the temperature of flue, entering water,
and leaving water (for hot water boiler) or steam pressure (for steam boiler).
All these temperatures shall not vary over 5.6 °C (10 °F) and the pressure shall
not vary over 13.8 kPa (2 psi) during a 30 minute period with three set of
measurements at 15 minute intervals.
6.1.5 Test data required are listed below (See later sections for
detailed measurement requirements). Three sets of test data shall be taken at
15 minute intervals and they shall be arithmetically averaged for capacity and
efficiency calculations.
6. 1.5.1 Measure carbon monoxide concentration (volumetric) of

flue gas. If the concentration is higher than that allowed in the contract
specification, the test shall be stopped and the burner retuned. If Orsat
apparatus is used for measuring gas concentration levels, the Orsat procedure
requires that carbon dioxide and oxygen levels are measured before carbon
monoxide
6. 1.5. Measure carbon dioxide or oxygen concentration level

of flue gas.
Page 118
4
9
6
7
8
5 ,
6. 1.5. 3 Measure flue gas temperature.
6. 1.5. For gas-fired units, record gas flow rate, gas

temperature and pressure at burner inlet of gas train.
6. 1.5. For oil-fired units, record oil flow rate oil

temperature and pressure at burner inlet.
6. 1.5. For hot water boilers, measure and record water inlet
and outlet temperature. If differential temperature measurement is chosen,
measure and record differential temperature.
6. 1.5. For steam boilers measure and record feed water

temperature, steam temperature, and steam pressure. Check the state of steam by
comparing steam temperature and pressure against steam tables. Steam must be
dry. If the steam is wet, the boiler must be rejected.
6. 1.5. Measure and record barometric pressure.
6. 1.5. Measure and record combustion air temperature.
6.1.6 During the 30 minute test period there shall be no blowdown

or soot-blowing.
6.1.7 Same procedures outlined in paragraphs 6.1.2, 6.1.3, 6.1.4,

6.1.5, and 6.1.6 above shall be repeated at 50%, and 75% load. For the 100% load
(full load) tests, the burner fuel control setting shall be at its highest level.
In addition to the measurements as required for part load tests, hot water flow
rate (for hot water boilers) or steam flow rate (for steam boilers), shall be
measured at 100% load test.
6.1.8 Measurement details.
6. 1.8.1 Heating values of fuel. Higher heating values of

fuels are required for combustion efficiency calculations.
* Gas company supplying the fuel can provide heating value

data for the time of the test. Heating values are usually quite steady for a
short period such as for boiler testing. Make sure the heating value data error
from the gas company is less than 1%.
* Oil-fired units need laboratory calorimetry tests to

determine the higher heating values of the oil. Sample oil should be send to
creditable laboratories for the test. Be certain that the oil used for the
performance test is the same oil for heating value determination and that the
laboratory conducting this service can keep the measurement error below 1%.
Page 119
6. 1.8. 2 Flue gas temperature.
* Flue temperature should be measured at the boiler flue

outlet close to the boiler to avoid errors caused by air leakage. For gas-fired
boilers having draft hoods or diverters, temperature should be measured upstream
of hoods and diverters. If temperature sensor must be located in breeching,
examine any possibility of air leakage between boiler flue outlet and the
temperature taking location. The temperature measuring section of the flue pipe
or breeching shall be insulated with foil-faced 0.051 m (2 in.) thick mineral
fiber or other high temperature insulation. The length of insulated section shall
not be less than three times of the flue or breeching diameter.
* For small boilers with a short smoke path, pay attention

to the location of the temperature sensing elements so that the sensors do not
sense the direct radiation effect of the fire.
* In order to reduce the effect of flue gas temperature

stratification, temperature traverse shall be measured at a rate of one
measurement per one square foot of cross sectional area on the measurement plane.
The measurement data shall be arithmetically averaged to represent average flue
temperature
6. 1.8. Flue gas component measurement.
* Flue gas sampling. If flue gas sampling line is used, it

should be made as short as possible and slope in the direction of flow. Also
check the following:
** The material of the sampling tube must be suitable for

the temperature of the flue gas.
** Check possible leakage of the tube at tube fittings and

around sampling holes at flue pipe or breeching. Make certain that the sample
gas represents the true flue gas.
** If metal tube is used, draw flue sample for at least

10 minutes through the tube before the sample is used for gas analysis, so that
the chemical reaction of the inner tube surface does not affect the results.
* Flue gas sensor.
** When flue gas sensor is directly placed in flue line,

check flue opening around sensor for possible air leakage.
** Flue sensing instrument installed as part of combustion

sensing and control device may be used to monitor flue composition for
commissioning purpose.
Page 120
4
2
3 3
** Portable or permanent sensing instrument must be

calibrated with standard gas for the entire instrument range.
* Flue gas measuring location shall be as close to flue gas

temperature measuring location as possible.
* Flue gas component measurement should follow immediately

the flue temperature measurement given in paragraph 6. 1.4. above.
6.2
(e) Combustion air temperature measurement. One measurement shall
be made in front of the boiler combustion air intake approximately 1.2 m (4 ft)
from the boiler. A radiation shield shall be used between the temperature sensor,
the boiler, and other high surface temperature equipment.
Electric boilers.
6.2.1 Electric boilers shall be tested for full capacity and for
efficiency at full load by input/output method.
6.2.2 The building air handling and/or other equipment may need to
be adjusted during the test to provide steady and approximately correct load.
6.2.3 Test data shall be taken after boiler has been running at
steady state conditions for at least 30 minutes. Steady state conditions of the
boiler operation is defined by measuring the temperature of entering water and
leaving water (for hot water boiler) or entering water and steam pressure (for
steam boiler). All these temperature shall not vary over 5.6 °C (10 °F) during
a 30 minute period with three set of measurements at 15 minute intervals.
6.2.4 Test data required are listed below.
6. 2. 4.1 Measure and record electricity input power rate of

heating elements and voltages of all three phases.
6. 2. 4. For hot water boilers, measure and record water inlet

and outlet temperature.
6. 2. 4. For steam boilers measure and record water inlet

temperature and steam pressure.
6. 2. 4. Measure and record hot water (for hot water boiler)

or steam (for steam boiler) flow rate.
Page 121

7.1 Boiler capacity.
7.1.1 Boiler capacity is calculated from 100% capacity test data.
7. 1.1.1 Steam boiler.
(q)out - M (H s - HJ
7. 1.1. 2 Hot water boiler.
(q)out “ M (H out - H in )
Symbols: (q) ou t “ boiler output, W (Btu/h)

M = mass flow rate of steam or hot water, kg/s (Ib/h), see
SE-37, 39, 41, or 43 of EXHIBIT 2-B
H s = enthalpy of steam, J/kg (Btu/lb) locate in steam table ,
knowing temperature and pressure

H„, H out ,
H in = enthalpy of feed water, hot water
supply, and hot water return, respectively,
locate in steam tables knowing their respective
temperature
7.1.2 Boiler capacity shall not be less than specified in the

contract specifications.
7.2 Boiler heat input.
7.2.1 For gas -fired units. Convert measured gas volume flow rate
to standard conditions. Standard conditions for gas is usually at 15 °C (60 °F)
and 101.3 kPa (30 in. of Hg) This standard conditions should be confirmed with
.
gas supplier who provides gas heating values.
Pm + Pb 15 + 273
Qs = Qm (* ) ( (For SI)
101.3 T m + 273
P m + P b x 13.57 60 + 460
Qs - Qm (- ) ( ) (For Customary)
30 x 13.57 Tm + 460
where: Q s = volume flow rate of gas at standard conditions,

m 3 /s (ft 3 /h)
3 3
Qm = measured flow rate of gas, m /s (ft /h)
P m *= measured gas pressure, kPa (in. of water)
P b = barometric pressure, kPa (in. of Hg)
T m = measured gas temperature, °C (°F)
Page 122
Then, calculate the heat input to the boiler:
(q) in = Q s x (HHV) g
where: (q)in = heat input rate,

W (Btu/h)
(HHV) g *= higher heating value of gas, J/m 3 (Btu/ft 3 )
7.2.2 For oil-fired units.
Q s « Qi x [1 - (T B - 15) x V f ]
(For SI)
Qs = Qn, x [1 - (T m - 60) x V f ]
(For Customary)
( q ) in - Qs X (HHV) 0
where: Q s = volumetric oil flow rate at 15 °C (60 °F) m 3 /s (gph) ,
Qn,
•= measured volumetric flow rate of oil, m 3 /s (gph)
T m = measured oil temperature at flow meter, °C (°F)
V f = specific volume factor to adjust volume change
due to temperature, if not available from oil
test lab, use 0.00068 per °C (0.00038 per °F)
(q) in = heat input rate, W (Btu/h)
(HHV) C = higher heating value of oil as supplied by
testing lab, J/m 3 (Btu/gal)
7.3
7.2.3 For electric units. Calculate heat input to electric elements
of boiler from measured electric energy:
( q ) in = W (For SI)
( q ) in = W x 3413 (For Customary)
where: (q)in = heat input rate, W (Btu/h)

W = watt meter reading, W
Boiler thermal efficiency at full load.
( q ) out
7.3.1 eff (in 1) x 100
(q)in
7.3.2 Boiler thermal efficiency at full load shall not be lower than
that required in the contract specification.
Page 123
7.4 Combustion efficiency at part loads (for gas and oil fired boilers
only)
7.4.1 Flue losses (q) f Flue losses may be obtained by using charts
.
supplied by burner manufacturers or other professional/trade associations.

Calculate the temperature difference between the temperature and combustion air
temperature. The flue loss is obtained from the charts as a function of the
measured percent of 02 (or C0 2 ) at the measured temperature difference.
7.4.2 The combustion efficiency is represented by:
eff (in %) = 100 - (Flue loss in percent)
7.4.3 Boiler combustion efficiencies at 25%, 50%, and 75% shall not
be less than those required in the contract specifications.
Page 124
. .
EXHIBIT 4-C TEST PROCEDURES FOR AIR-HEATING FURNACES
1. Scope. The test procedures in this EXHIBIT apply to gas, oil, or electric
fired packaged furnaces used for building air heating systems. Tests to confirm
capacity and energy conversion efficiency are covered in this EXHIBIT.
Functional tests of furnaces may be found in EXHIBIT 4-A, INSPECTION PROCEDURES
FOR BOILERS AND FURNACES.
a. ASHRAE Standard 103-1988R (Methods of Testing for Heating Seasonal

Efficiency of Central Furnaces and Boilers) provides procedures for determining
heating seasonal efficiency of residential central furnaces and boilers using
gas, oil or electric for fuel. It gives cyclic and part load testing method,
test data manipulation, and calculation of seasonal performance.
b. ANSI Z21.7 (Standard for Gas-Fired Warm Air Furnaces) gives the minimum
construction, safety, and performance requirements for gas furnaces.
c. See EXHIBIT 4-A INSPECTION PROCEDURES FOR BOILERS AND FURNACES for other
standards
3. General.
3.1 All furnaces shall be tested for output at full capacity to verify
capacity requirements, except certain small furnaces specifically exempt by
contract specifications. Check contract specifications for requirement.
3.2 All fossil -fuel furnaces shall be tested for combustion efficiency at
full load.
3.3 Two ways are generally used in the industry to test furnace
efficiencies. They are tested by input/output method or by heat loss method.
Since air heating furnaces in federal building are relatively small as compared
to other heating equipment (boilers), commissioning tests should be concentrated
on verifying capacity and combustion efficiency.
3.3.1 Gas and oil fired furnaces shall be tested for combustion
efficiency (not thermal efficiency) at full capacity by using heat loss method.
3.3.2 Electric furnaces need not be tested for combustion

efficiency
Page 125
3.4 The input/output method measures heat in fuel consumed and the heat
output of the furnace. Furnace efficiency is calculated by:
output
Efficiency (percent) = x 100
input
3.5 Combustion efficiency is calculated by:
efficiency (percent) = [1 - (sensible loss of dry gas)

- (hydrogen loss)] x 100
Hydrogen loss is the loss of water vapor of combustion air.
3.6.1 Flue losses account for the biggest part of furnace losses.
Major effort of commissioning test should be on measuring flue losses.
3.6.2 Furnace surface losses are small compared to stack losses.

Therefore, it is ignored in commissioning tests for furnaces.
3.6.3 Loss of unburned combustibles is minimized by burner tuning.

The contract specification gives the limitations of the amount of unburned
combustibles, therefore, the commissioning team should confirm that the amount
of unburned combustibles in the flue gas is below what is specified.
4. Preparation for tests.

4.1 Before the scheduled performance tests, the project contractor or
manufacturer's representative should have prepared and tuned the furnace in
according to the recommendations of the manufacturer.
4.2 Make sure that furnace and air filters are cleaned, air circulation
fan (and combustion air fan, if provided) are adjusted correctly and oiled, and
burner are tuned for operation.
4.3 All furnace inspection items should be performed and requirement

satisfied before performance tests are attempted. See EXHIBIT 4-A for inspection
requirements
4.4 The commissioning team should coordinate with the contractor and
building user to arrange appropriate time for testing so that the building
occupants will not be subjected to overheating conditions.
Page 126
. . 4
2
3 .
5. Instrumentation.
5.1 Make sure that all instrumentation are in good working orders and are
in calibration. See Chapter 2 BASIC MEASUREMENT for calibration of instruments.

by the contractor or manufacturer
1.1 may be used for performance tests, if they meet
the accuracy and calibration requirements of this guide.
5.3.1
Temperature.
5. 3. Flue temperature. The total measurement system error

shall not exceed +/- 2.8 ° (5 °F) Most temperature measurement instruments
.
suitable for the temperature range of up to 538 °C (1000 °F) may satisfy this
requirement
5. 3. 1.2 Combustion air temperature. The total measurement

error shall not exceed +/- 0.6 °C (1 °F) .
5. 3. 1.3 Supply air and return air temperature. The total

5.3.2
measurement error shall not exceed +/- 0.3 °C (0.5 °F) Direct measurement of
.
temperature differential (supply air temperature minus return air temperature)

is preferred than measuring individual supply and return temperatures. The total
measurement error for differential temperature measurement shall not exceed +/-
0.3 °C (0.5 °F)
Flue gas component measurement. Orsat apparatus may be used

to measure carbon dioxide, oxygen, and carbon monoxide from the same gas sample.
Portable oxygen, carbon dioxide, or carbon monoxide monitors may be used to
measure individual gas components in the flue gas
Orsat apparatus. See EXHIBIT 2 -A COMMONLY USED FIELD

5. 3. 2.1
TEST INSTRUMENTS. Be certain that the person conducting flue gas measurement
with Orsat apparatus is experienced in its use and the chemical reagents are
fresh.
5. 3. 2. Oxygen monitor. The total measurement error shall not

exceed +/- 0.1 percentage points.
5. 3. 2. Carbon dioxide monitor. The total measurement error

5. 3. 2. Carbon monoxide monitor. The total measurement error

shall not exceed +/- 0.01 percentage points. t
Page 127
5. 3. 2. Gas concentration monitors must be calibrated with

standard gas with concentration close to that of the flue gas.
5.3.3 Furnace air flow rate. Use pitot traverse and water manometer
to measure either supply or return air flow rate. The measurement error shall
not exceed +/- 5 percent of the quantity measured.
5.3.4 Electric usage for heating element of electric furnace. The

measurement error of watt-hour meter shall not exceed 1%.
5.3.5 Pressure at flue pipe. Measurement error not to exceed 12.4

Pa (0.05 in. of water).
6. Test Procedures for full load capacity and combustion

efficiency. (see paragraph 3. above for required tests)
6.1 The test to confirm the furnace capacity and combustion efficiency is
conducted under steady state operation. Turn thermostat up for about 5.6 °C (10
°F) to initiate furnace operation. Measure the supply air temperature at 5
minute intervals. If the variation of 3 measurements are within 1.7 °C (3 °F) ,
the system is considered stabilized and test data may be collected.
6.2 Test data required are listed below (See later sections for detailed
measurement requirements) Three sets of test data shall be taken at 15 minute
.
intervals and they shall be arithmetically averaged for capacity and efficiency
calculations
6.2.1 Gas and oil-fired furnaces.
6. 2. 1.1 Measure carbon monoxide concentration (volumetric) of

flue gas. If the concentration is higher than that allowed in the contract
specification, the test shall be stopped and the burner retuned. If Orsat
apparatus is used for measuring gas levels, carbon dioxide and oxygen levels are
measured before carbon monoxide.
6. 2. 1.2 Measure carbon dioxide or oxygen concentration level

of flue gas
6. 2. 1.3 Measure flue gas temperature.
6.2. 1.4 Measure room temperature where the furnace is

situated. This temperature will be used as combustion air temperature unless
combustion air is ducted to unit.
6. 2. 1.5 Measure supply air temperature.
6. 2. 1.6 Measure return air temperature.
Page 128
4
2
5
3 .
6. 2. 1.7 Measure return air dew point or relative humidity.
6 . 2 . 1.8 Measure barometric pressure.
6. 2. 1.9 Measure air flow rate,
6 . 2.2 Electric furnaces
6 . 2 . 2.1 Measure room temperature where the furnace is

situated.
6 . 2 . 2. Measure supply air temperature.
6 . 2 . 2. Measure return air temperature.
6 . 2 . 2. Measure return air dew point or relative humidity.
6 . 2 . 2. Measure barometric pressure.
6 . 2 . 2.6 Measure air flow rate.
6.2.3 Measurement details.
Heating values of fuel.

6. 2. 3.1 Higher heating values of
fuels are required for combustion efficiency calculations.
* Gas company supplying the fuel can provide heating value

data for the time of the test. Heating values are usually quite steady for a
short period such as for furnace testing. Make sure the heating value data error
from the gas company is less than 1%.
* Oil-fired units need laboratory calorimetry tests to

determine the higher heating values of the oil. Sample oil should be send to
creditable laboratories for the test. Be certain that the oil used for the
performance test is the same oil for heating value determination and that the
laboratory conducting this service can keep the measurement error below 1%.
6. 2. 3. Flue gas temperature.
* Flue temperature should be measured at the furnace flue

outlet close to the furnace to avoid errors caused by air leakage. For gas-fired
furnaces having draft hoods or diverters, temperature should be measured upstream
of hoods and diverters. If temperature sensor must be located in breeching,
examine any possibility of air leakage between furnace flue outlet and the
temperature taking location. The temperature measuring section of the flue pipe
or breeching shall be insulated with foil-faced 0.051 m (2 in.) thick mineral
fiber or other high temperature insulation. The length of insulated section
shall not be less than three times of the flue or breeching diameter.
Page 129
* Pay attention to the location of the temperature sensing

elements. The sensors shall not sense the direct radiation effect of the fire.
* reduce the effect of flue gas temperature

In order to
stratification, three measurements at different locations of the same flue
cross-sectional plane shall be measured. The measurement data shall be
arithmetically averaged to represent average flue temperature.
6. 2. 3. Flue gas component measurement.
* Flue gas sampling. If flue gas sampling line is used, it

should be made as short as possible and slope in the direction of flow. Also
check the following:
** The material of the sampling tube must be suitable for

the temperature of the flue gas
** Check possible leakage of the tube at tube fittings and

around sampling holes at flue pipe or breeching. Make certain that the sample
gas represents the true flue gas.
** If metal tube is used, draw flue sample for at least

10 minutes through the tube before the sample is used for gas analysis, so that
the chemical reaction of the inner tube surface does not affect the results.
* Flue gas sensor.
** When flue gas sensor is directly placed in flue line,

check flue opening around sensor for possible air leakage.
** Portable or permanent sensing instrument must be

calibrated with standard gas for the entire instrument range.
* Flue gas measuring location shall be as close to flue gas

temperature measuring location as possible.
* Flue gas component measurement should follow immediately

the flue temperature measurement given in paragraph 6. 2. 3. above.
6. 2. 3. Furnace room air temperature measurement. One

measurement at approximately 1.2 m (4 ft) in front of the furnace shall be made.
A radiation shield shall be used between the temperature sensor and the furnace.
6. 2. 3. Supply and return air temperature. See EXHIBIT 2-C

STANDARD TEST PROCEDURES for details.
6.2. 3.6 Air flow rate. See EXHIBIT 2-C STANDARD TEST
PROCEDURES for details.
Page 130
. . ) : ]
7. 7.1
Calculations and rate performance. (See EXHIBIT 2-B for Standard
Equations of parameter calculations)
Furnace capacity.
Q
(*l)out ^ (ôut “
în)
V
Symbols
(q) out = furnace capacity, W (Btu/h)
Q - volume flow rate of air, m 3/s (ft 3 /m)
v = specific volume of air (average of inlet and
outlet temperature), m 3 /kg (ft 3 /lb)
H out = enthalpy of air at outlet, J/kg (Btu/lb)
H in = enthalpy of air at inlet, J/kg (Btu/lb)
7.2 Furnace capacity shall not be less than specified in the contract
specifications
7.3 Combustion efficiency (required for gas or oil fired furnaces at full
load only)
7.3.1 Sensible flue loss (q) f . Sensible flue losses maybe obtained
by either using equations or charts.
7. 3. 1.1 When calculation is preferred, the following equations

shall be used:
B
R «= A +
X
100
L « ([(1 + AF) (CF(i) + AF (R - 1) (CA(i) )
HHV
x [
(T gas + 460)* - (T air + 460)*])
where: R = ratio of combustion air to stoichiometric air, dimensionless

X = measured concentration of C0 2 (by volume, %)
HHV «= higher heating value of fuel, Btu/lb
Tgas = flue gas temperature, °F
T air = combustion air temperature, °F
CA( 1 ) = 2.5462121X10' 1
CA( 2 - - 3 0260126xl0~ 5 .
CA( 3 = 2 7608571x10'® .
Page 131
CA(4) «= -7 4253321xl0" 12
.
CA(5) - 6 4307377xl0' 16
.
i — an index, 1 through 5
A, B, AF, CF = constants from following table:
A B AF
Natural gas 0.09194 10.96 14.56

No. 2 oil 0.0679 14.22 14.56
CF(1) CF(2) CF(3)
Natural gas 2.5949478X10’ 1 - 4 9475802xl0‘ 6

. 1 . 3885838x10'®
1 -6
No. 2 oil 2 4361163X10'
. 3 . 6702686xl0 8 . 7098897xl0' 9
CF(4) CF(5)
Natural gas -2 8059994xl0‘ 12

. 3 . 7682444xl0" 17
12
No. 2 oil - 1 . 3619019xl0' - 1 . 5029209xl0' 16
(b) When using charts is preferred, calculate the temperature

difference between the flue temperature and the combustion air temperature. Using
this value and the R value as calculated in the previous paragraph on sensible
heat loss charts (charts 1 through 4) the sensible heat loss may be directly
,
read. The loss of water vapor of combustion product (also called hydrogen loss)
is 9.55% for natural gas and 6.50 for No. 2 oil. The total combustion loss is
the sum of sensible loss and hydrogen loss.
6.4 Furnace combustion efficiency shall not be less than that specified
in the construction specifications.
Page 132
1%)
XC02,
0R
S
XC02,
r t,s OR r t,f H
Chart 1 Ratio of Total Combustion to Stoichiometric Air
Page 133
400 350
(J)
SS‘Jiv
HO
</5 SS‘S
to
1V
r t,s w rt,f H
Chart 2. Steady-State Heat Loss Versus Ratio of Total

Combustion to Stoichiometric Air (No. 1 Oil)
Page 134
200 sr
t/i
CO
CO
CO
CO

Combustion to Stoichiometric Air (No. 2 Oil)
Page 135
|j)
SSJjy
HO
SS‘Sjy
r t,s «t,f I")

Combustion to Stoichiometric Air (Natural Gas)
Page 136
. . . .
CHAPTER 5 AIR HANDLING EQUIPMENT AND SYSTEMS
1. Scope. This chapter provides inspection and testing procedures for air
handling equipment and systems that use chilled water as cooling medium.
Included are central station field erected systems, central station factory
packaged systems, and room terminal units (fan coil units and unit
ventilators). Unitary air handling units that use refrigerant as cooling
media are not included in this chapter. They may be found in chapter 8,
Unitary Air Conditioning Equipment. Certain temperature controls are included
in Chapter 6, Building Automation Systems.
a ARI Standard 410
.
- Standard for Forced-Circulation Air-Cooling and
Air-Heating Coils
b. ARI Standard 430 - Standard for Central-Station Air-Handling Units.
c ARI Standard 440 - Standard for Room Fan-Coil Air-Conditioners.
d. ARI Standard 610 - Standard for Central System Humidifiers.
e. ARI Standard 630 - Standard for Selection, Installation, and Servicing

of Humidifiers.
f. ARI Standard 670 - Standard for Fans and Blowers.
g- ARI Standard 850 - Standard for Commercial and Industrial Air Filter
Equipment
h. ASHRAE Standard 33 - Methods of Testing Forced Circulation Air Cooling

and Air Heating Coils.
i. ASHRAE Standard 41.6 - Standard Method for Measurement of Moist Air

Properties
j. ASHRAE Standard 51 - Laboratory Methods of Testing Fans for RAting.
k. ASHRAE Standard 52 - Method of Testing Air-Cleaning Devices Used in

General Ventilation for Removing Particulate Matter.
l. ASHRAE Standard 62 - Ventilation for Acceptable Indoor Air Quality.
m. ASHRAE Standard 71 - Method of Testing for Rating Unit Ventilators.
Page 137
n.ASHRAE Standard 90.1 - Energy Efficient Design of New Non-Residential

Buildings and New High-Rise Residential Buildings.
o. ASHRAE Standard 111-1988 - Practices for Measurement, Testing,

Adjusting, and Balancing of Building Heating, Ventilation, Air Conditioning
and Refrigeration Systems.
p. Associated Air Balance Council - National Standards for Total System

Balance
q.National Environmental Balancing Bureau - Procedural Standards for

Testing-Balancing-adjusting of Environmental Systems.
r. Applicable codes of the National Fire Protection Association.
s. Applicable codes of Underwriters Laboratories, Inc.
3. Air Handling Equipment and System Inspection.

3.1 The air handling equipment and systems shall be inspected for
construction and installation to meet safety and functional requirements.
3.2 See EXHIBIT 5-A for inspection procedures. See Appendix for
inspection check lists.
4. Air Handling Equipment and System Testing.

4.1 The air handling equipment and systems shall be tested in the field
to verify capacity and performance requirements of the contract
specifications
4.2 Two basic type of tests shall be included:
4.2.1 The capacity and other performance compliance of the air

handling system and components.
4.2.2 The functional compliance of the automatic control system.
4.3 If building load at time of testing does not correspond to system

capacity requirements, introduction of false loads to the air handling unit or
its components may be necessary. However, tests shall not cause excessively
uncomfortable conditions in the building. Providing false load is the
responsibility of the project contractor.
4.4 See EXHIBIT 5-B for test procedures. See Appendix for test work
sheets
Page 138
EXHIBIT 5-A INSPECTION PROCEDURES FOR AIR HANDLING SYSTEMS

central station packaged and field erected air handling units, unit
ventilators, room fan coil units, and their associated automatic temperature
controls. See Chapter 6 for automatic temperature controls of systems having
building automation systems.
a. ARI Standard 630 (Standard for Selection, Installation, and Servicing
of Humidifiers) describes humidifier selection procedure, installation
practices, and service practices of humidifiers used in central stations and
self-contained applications.
b. ASHRAE Standard 62 (Ventilation for Acceptable Indoor Air Quality) is

a design standard which gives ambient air quality guidelines and outdoor air
requirements for most space ventilation applications. It also give general
requirements for ventilation systems and equipment.
3. Air handling system general inspection.

3.1 Review equipment manufacturer's instructions on start-up and
operation procedures.
3.2 Give complete inspection of fan, motor, air filters, cooling coils,
heating coils, dampers, fan and coil bases, vibration isolation units, and
their associated equipment, including associated electrical equipment, piping,
ductwork, etc. Be sure that no apparent damage or rusting occurred.
3.3 Check equipment name plates (air handling unit, fan, motor, air
filter, coils, etc.) to verify equipment model and serial number. They must
have the same model numbers as approved submittals.
3.4 Check for headrooms and access spaces around unit for operation and
maintenance. Manufacturer's recommended spaces must be provided unless the
contract documents specify otherwise. Pay special attention to coil and filter
replacement and cleaning spaces and access spaces.
3.5 Inspect equipment room for possible fire hazards. The room should
be kept free of combustible material and construction debris.
3.6 Check compliance of equipment room ventilation requirement with

project drawings and specifications. If automatic dampers are specified and
installed, test damper operation.
Page 139
3.7 Verify service piping, pipe fittings and accessory equipment for
the air handling equipment against project drawings and equipment
manufacturer's recommendations for completeness and proper installation.
Fittings and accessories include but not limit to valves, strainers,
thermometer wells, piping supports, steam traps, etc.
3.8 Check water flow direction marks of check valves and flow switches.
3.9 Check piping at equipment connections. Pipes should be supported

from building structure without undue stress on coils.
3.10 All moving parts (motors, belts, etc.) should have protective
shields for personnel safety in accordance with job specifications.
3.11 Check alignment of motor driven equipment. Using some simple

tools such as straight edges, square edges, plumb lines, and strings yield
good results. If these instruments indicate the possibility of misalignment,
checking with more sophisticated instruments should be required of the
contractor. Also observe shaft and coupling for misalignment while equipment
is running.
3.12 Observe belt tightness of fans. Use belt tension gage if needed.
Belt tension should be as recommended by belt manufacturer. Remove equipment
access panels as necessary.
3.13 Make sure required lubrication is complete (fan, motor, etc.).

Use a grease gun if necessary.

thermometers, gages, temperature and flow measuring and control devices.
Required straight pipe runs and arrangements for temperature and flow
measuring devices must be met.
3.15 Verify installed wiring against project drawings and

3.17 Check safety control wiring connections. All safety control

switches ( switches respond to temperature, pressure, smoke, etc. to break the
safety control circuit) should be connected in the ungrounded conductor.
3.18 Check all electrical connections for tightness with screwdriver,

wrench, etc. as necessary.
Page 140
. . .
3.20 Test-run motors (fan, pump, etc.) to check correct direction of

rotation.
3.21 Check surface paint for damages and omissions. Equipment

nameplates must not be painted over. Required equipment labels must be present
and legible.
3.23 Note any water, oil, or steam leaks.
3.24 Inspect duct connections at air handling unit for excessive air
leakage
4. Fan.
4.1 Inspect fan housing access door and pressure latches for tightness.
Open and close doors to detect interference of door with thermal insulation
and other equipment.
4.2 Check assembly bolts of field assembled fans for any loose bolt.
4.3 Inspect bearing for proper oil or grease application. Grease lines
for bearings should extend to outside of duct connections with grease fittings
if specified. Oiling shall not require dismantling of fans, ducts, or other
equipment if specified.
4.4 Inspect belt guard for access to oiling, speed counting device, and
other maintenance requirements.
4.5 Observe fan steadiness during operation and excessive vibration

transmission to building supporting structure.
4.6 For outlet damper or inlet vane controls inspect control linkage
manually or by manipulating controller for the full range of the stroke. When
a single operator controls inlet vanes of double inlet fans, inlet vanes on
both inlet openings must move in unison. Inspect inlet vane rotation
direction with respect to that of the fan wheel.
4.7 Fans exposed to weather should have protective weather hoods over
motors and drives if specified.
4.8 For fans without duct connections, unless they are housed in
plenums, they must be provided with protective devices for personnel safety
such as wire mesh or expanded metal screens at inlets and outlets if
specified
4.9 For power roof ventilators check curb watertightness
Page 141
4.10 For fans not enclosed in air handling unit casings, make sure
flexible duct connections are installed between fans and ducts if specified.
Check specifications for material and construction of flexible connections.
5. Heating and cooling coils.

5.1 Inspect heat transfer fins for damages.
5.2 Verify project specified or manufacturer's recommended slope of

heat transfer tubes for drain requirements.
5.3 Inspect baffles between coils and casing to assure that air is not
bypassing coils.
5.4 Inspect cooling coil drain pans. Coils must have individual pans
with drain pipes for multi-coil assembly to avoid flooding of lower coils if
specified. Similar arrangement is required for sprayed coil dehumidifiers.
5.5 Inspect pipe fittings, valves, and coil accessories in accordance

to specifications and drawings. Included are water supply, water return,
steam supply, condensate return, piping to sprayed coils, air vents, and
drains
5.6 Inspect steam coils for possible coil freezing problem. Good
condensate draining must be provided: adequate slope of tubes, adequate head
between coils and steam traps (minimum 18 in.), and vacuum breakers at high
position of coils. Adequate sizing of steam traps should be checked if the
requirements are not given in the contract specifications. Check for counter
flow, air vents, drains, water trap on cooling coil, piping and water coil.
5.7 Steam main drips must be provided before coil connections if

specified.
5.8 Check steam traps and condensate piping of steam coil temperature.
They must not be unduly hot.
5.9 Inspect primary element installation for flow measurement devices.

The specified distance of pipe lengths and accessories (such as water
straightening devices) must be viewed as minimum requirements.
6. Air filters.
6.1 Inspect filters for air leakage between filters and holding frames
and between filter assembly and unit casing. Inspect positive sealing devices
for air leakage, if specified.
6.2 For automatic renewable type air filters, inspect medium advancing
Page 142
. . .
and override operation (pressure control, timer setting, media switch, etc.
See specifications for project requirements).
6.3 Inspect filter gage sensing tips for correct static pressure
sensing
6.4 For inclined manometer type filter gages check for correct
installation levels.
6.5 Filter holding frames must be anchored securely to air handling

unit casing as per design drawing/specifications.
6.6 Make sure adequate access spaces are provided for filter media
replacement as per design drawings/specifications.
6.7 Filter media must be new at the time of commissioning inspection.
6.8 Check the number of spare filters provided by the contractor

against contract specification requirements.
7 . Dampers
7.1 Verify blade arrangement, bearing material and edge sealing
material
7.2 Inspect full range of damper movement by manipulating actuator.

Verify damper closing position.
7.3 Felt strips should be provided for backdraft dampers if specified.

Dampers shall not rattle during operation.
7.4 all dampers in ducts must have access doors if specified. Doors
must be air tight.
8. Air louvers.
8.1 Verify material, arrangement, and dimensions.
8.2 Verify material and mesh size of bird screens.
9. Casings.
9.1 Inspect casing for rigidity (reinforcement and adequate bracing).
9.2 Inspect casing for integrity.
Page 143
9.3 Verify access door sizes, gasket tightness, and latch arrangement.
9.4Make sure flexible connections are installed between air handling

equipment and duct system. Check specifications for material and construction
of flexible connections.
9.5 For outdoor installation with factory supplied enclosures, inspect

gaskets or caulking at joints for weather protection. Also inspect curb
flashing for watertightness
10. Thermal insulation.

10.1 Check thermal insulation for damages and omissions.
10.2 Material, thickness, and finish of thermal insulation and vapor

barrier must be as specified.
10.3 Check vapor barrier downstream of cooling coil for integrity.
11. Controls.
11.1 Review installed control systems with contract documents and
submittals to assure that the installations are as required.
11.2 The contractor must demonstrate correct calibration of all

instruments. These include temperature (water, air), pressure (steam), and
other instruments as the contract specified.
11.3 Observe general operation of control system. Look for incorrect

ranges and settings.
11.4 All controls containing mercury switches should be checked for

proper leveling.
11.5 Examine valve operation for tight closing. Valve motors and
linkages should be installed securely. Linkages should move through the
entire stroke without binding or interfering with other objects.
11.6 Examine damper operation for position (closing tight?). Damper

motors and linkages should be installed securely. Linkages should move
through their entire stroke without binding or interfering with other objects.
11.7 If pneumatic controls are used for system controls, check the
following:
11.7.1 Check control air tubing connections for tightness.
Page 144
. .
11.7.2 Check air filters (both intake air and air line)of air
compressors for cleanliness.
11.7.3 Check air compressor motor alignment.
11.7.4 Check air compressor belt tightness.
11.7.5 Make sure protective shields are provided for belts and
pulleys
11.7.6 Check compressor oil level and oil filter cleanliness.
11.7.7 Test open air tank drain for possible water accumulation.
11.7.8 Check condensers of control air refrigeration units for

cleanliness
11.7.9 Check for correct air pressure at air tanks and after
pressure reducing valves.
11.7.10 Check control diagrams, complete and framed with proper

item identification, understandable sequence description, etc.
11.7.11 Check inside control panels: everything labeled

correctly, installed neatly, settings marked, tubing numbered, appropriate
last-minute notes attached to panels, all features as specified.
11.7.13
11.7.12 Check for air pressure gauges installed throughout system
as specified, and reading correctly, both statically and during system
operation.
Check controls functioning accurately without hunting.
11.8 For electrical and electronic control systems check for loose wire
connections, broken wires, and rust terminals.
11.9 Check correct voltage of power supply.
11.10 Inspect electronic systems for ground shield cable and possible
interference of magnetic field with signals.
11.11 Check safety features of air handling controls such as coil

freeze protection and alarm bells.
11.12 Verify interlocking of equipment.
11.13 Note any malfunction device.
Page 145
11.14 Verify entire control installation in accordance with approved

submittals and operation manuals. See EXHIBIT 5-B for testing of control
functions
12. Fan coil units and unit ventilators.
12.1 Check type of units (wall hung, free standing, suspended,

concealed) to be the type specified. All accessories should be complete.
12.2 Check motor type, speed, and construction to be same as specified.

Plug in electric wires must be furnished. If oiling is required for motor
bearings, extended oiling tubes should be provided.
12.3 Check fan construction and material.
12.4 Check cabinet, inlet and outlet grilles to be as specified. Check

for dent or paint damages.
12.5 Check access doors for valves and controls.
12.6 Material and construction of drip pans should be as specified.
12.7 Check air filter type for specification compliance. Both outside
air and recirculated air must go through air filters.
12.8 Check fan, damper, and valve controls for specification

compliance. See EXHIBIT 5-B for functional test of controls.
12.9 Coil types and valve assembly shall be as specified. Check for
heat transfer fin damages.
12.10 Check acoustic and thermal insulation for completeness, material,

thickness, and face treatment.
12.11 Dampers should have continuous seals as specified.
12.12 If wall boxes are used for outside air, check box material and
construction. Bird screen shall be provided as specified.
Page 146
EXHIBIT 5-B TEST PROCEDURES FOR AIR HANDLING SYSTEMS
1. Scope. The test procedures described in this EXHIBIT apply to central

station packaged and field erected air handling units, room fan coil units,
room air terminal units, and their associated automatic temperature controls.
Also see Chapter 6 for automatic temperature controls of systems having
building automation systems.
a. ARI Standard 410 (Standard for Forced-Circulation Air-Cooling and
Air-Heating Coils) describes the method of testing and rating of forced air
cooling and heating coils and the method of establishing coil performance by
extension of test data to operating conditions other than test. It lists a
range of standard rating conditions for important operational parameters such
as air face velocity, fluid velocity in tubes, temperature of air and fluid.
Fluid used in coils tubes are refrigerant, cold and hot water, steam, and
ethylene glycol solution. This standard is used in conjunction with ASHRAE
Standard 33 (Methods of Testing for Rating Forced Circulation Air Cooling and
Air Heating Coils.
b. ARI Standard 430 (Standard for Central- Station Air-Handling Units)

describes the definition, classification, standard components, and testing and
rating requirements of central-station air-handling units. It is intended to
be used in conjunction with ASHRAE Standard 51 (Laboratory Methods of Testing
Fans for Rating). Test results of one unit are extended to other units by the
application of fan laws.
c. ARI Standard 440 (Standard for Room Fan-Coil Air-Conditioners)

describes the definition, classification, standard components, and testing and
rating requirements of room fan coil units. It is intended to be used in
conjunction with ASHRAE Standard 79 (Methods of Testing for Rating Room Fan
Coil Air-Conditioners). The standard testing and rating conditions are 80 F
dry bulb and 67 F wet bulb entering air, 45 F entering water, 55 or 60 F
leaving water temperature, negligible air friction through the coil, highest
fan speed setting and nameplate electrical characteristics at the unit.
d. ARI Standard 610 (Standard for Central System Humidifiers) describes

the testing and rating requirements of central station humidifiers installed
in ducts of air heating type heaters. It states the standard testing and
rating conditions of air velocity, air temperature and pressure, water
temperature and pressure of various applications (humidifier location in
relation to the central system). The humidification rate is measured by the
net water added to the air stream at the entering air conditions.
Page 147
e. ARI Standard 670 (Standard for Fans and Blowers) describes testing and
rating requirements for fans and blowers. This standard is used in
conjunction with ASHRAE Standard 51 (Laboratory Methods of Testing Fans for
Rating Purposes). Test data may be extended by use of fan laws to other fans
with certain restrictions.
f. ARI Standard 850 (Standard for Commercial and Industrial Air Filter
Equipment) describes classification, testing and rating requirements,
performance and safety requirements for factory-made air filter devices and
air filter media. This Standard is used in conjunction with ASHRAE Standard
52 (Methods of Testing Air Cleaning Devices Used in General Ventilation for
Removing Particulate Matter) It states standard rating conditions and values
.
of standard ratings to be published. It also requires a breaching test to

ascertain that no evidence of tearing, dislocation, or other damage to the air
filter device.
g. ASHRAE Standard 33 (Methods of Testing Forced Circulation Air Cooling

and Air Heating Coils) prescribes laboratory testing methods for air cooling
and air heating coils. It describes test methods and procedures, testing
instruments and apparatus, test data to be recorded, calculations to be made
from test data, and specified standard thermodynamic properties. It is not
intended for field testing.
h. ASHRAE Standard 41.6 (Standard Method for Measurement of Moist Air

Properties) gives recommended practices and procedures for measurement and
calculations of moist air properties. It describes moisture measuring
instruments, the ranges of conditions these instruments are practical, their
accuracies, and the techniques of use to achieve desired accuracies. The
instruments included are psychrometer dew point hygrometer, heated electrical
,
salt-phase transition hygrometer, Dunmore type sensor, and electrolytic

hygrometer. Calibration and reference standards are also discussed.
i. ASHRAE Standard 51 (Laboratory Methods of Testing Fans for Rating)

prescribes methods for laboratory testing of rating fan performance in terms
of flow rate, pressure, power, air density, speed of rotation, and efficiency.
It gives basic fan-related definitions, instruments and methods of
measurements, test equipment and setups, calculation equations, and some air
and equipment data. It must be cautioned that when performing fan tests,
field conditions of fans, ducts, and other associated equipment usually alter
test results significantly from those of laboratory conditions.
j ASHRAE Standard 52 (Method of Testing Air-Cleaning Devices Used in

.
General Ventilation for Removing Particulate Matter) describes the test

apparatus and procedures for testing the performance of air-cleaning devices
used in air handling applications. It evaluates air-cleaning devices by
determining their particulate arresting efficiencies, time for replacement or
cleaning, and their resistances to air flow. Both ambient atmospheric
contaminants and synthetic dust may be used in tests. This Standard should
not be used for testing air-cleaning devices having efficiencies higher than
Page 148
98%.
ASHRAE Standard 71 (Method of Testing for Rating Unit Ventilators)

k.
describes laboratory testing methods, instruments, apparatus, and test
procedures for unit ventilators. It also gives calculation equations for air
and other variables of unit heaters.
l. ASHRAE Standard 79 (Methods of Testing for Rating Room Fan-Coil Air

Conditioners) prescribes laboratory testing and rating methods for fan coil
units. It describes test instruments and measurement methods, apparatus, test
procedures, and calculation equations.
m. ASHRAE Standard 90.1 (Energy Efficient Design of New Non-Residential

Buildings and New High-Rise Residential Buildings) prescribes the requirements
for efficient energy design of new human occupied buildings. Covered are
exterior building envelopes, HVAC systems and equipment, service water
heating, lighting systems, and other auxiliary equipment. Mandatory
requirements are specified for compliance of energy efficient use.
Alternative methods of compliance are allowed: prescriptive, system
performance, and annual energy consumption.
n. Associated Air Balance Council National Standards (National Standards

for Total System Balance) is an industry standard for establishing a minimum
set of field and balancing standards. This Standard together with the one in
paragraph o. below differ from all other standards listed here in that the
purpose of these two standards are solely for field testing, adjusting, and
balancing of HVAC systems. This Standard describes measurement instruments
and their use, some basic system design information, and procedures for
testing, adjusting, and balancing of air and water systems. Detailed
equipment testing is not included.
o. National Environmental Balancing Bureau Standard (Procedural Standards

for Testing-Balancing-adjusting of Environmental Systems) is a standard
similar in purpose and practice to the previous standard for field testing,
adjusting and balancing of HVAC systems.
3. General.
3.1 One of the most important measurement in air handling system

testing is the measurement of air flow rates of the system. This measurement
is used in most installation to verify almost all component (fan, heating
coils, cooling coil, air filter, humidifier, and other components) capacities.
3.2 Field tests of air handling systems are separated into two groups
in this guide. The air handling unit component tests are based on steady
state operating conditions to verify the peak capacities of the components.
The air handling system operational tests mainly verify the control operations
of the systems.
Page 149
3.3 Unless specifications require otherwise, air handling systems

having air flow rates over 1.888 m 3 /s (4000 ft 3 /min) should have full level
tests as outlined in this guide. For air handling systems having air flow
rates at or less than 1.888 m 3 /s (4000 ft 3 /min)
,
total air flow rates and
cooling/heating temperature differentials (from inlet to outlet of units)
should be verified and the components tests are not required.
3.4 Functional inspection and test process is based on the premise that
the construction contractor has tested, adjusted, and balanced the entire air
and water systems and is ready for normal operation. Certain preparatory
procedures listed in this section are needed before commencing functional
inspection and tests of components and systems.
3.5 All architectural openings, such as windows and doors, should be at

their normally used positions (Check both architectural and mechanical
drawings)
3.6 All fans (supply, return, exhaust, transfer) which may influence
the air balance in the area should be operating at their normal conditions.
3.7 All system interlocks should be at their normal operational

conditions
3.8 All safety devices and provisions have been inspected and tested
already
3.9 The space temperature and humidity controls should be set at normal
operating conditions.
3.10 air flow rate measurement of fans and subsystems (if air flow
rates differ from that of the main fan) should be performed before other
tests
3.11 All manual damper positions as set by the construction contractor

should be marked before they are attempted to be changed for tests, so that
their original positions may be restored, if necessary.
3.12 It should be recognized that most installations of air systems are

not at ideal conditions for flow measurements. Extraordinary caution and
details should be paid to the selection of sensor locations and measurement
techniques
3.13 Fan ratings supplied by fan manufacturers and air flow rates of
the design documents are generally in standard air conditions (approximately
dry air at 21.1 °C (70 °F) and 101.3 kPa (29.92 in. of Hg) or 1.20 kg/m 3
,
3
(0.0750 lb/ft ) unless noted otherwise. It is generally adequate to use
volumetric flow rates for commissioning purpose. If the temperature,
humidity, and barometric pressure differ substantially from those of the
standard air, the volumetric flow rates from the test results must be
Page 150
.
adjusted.
3.14 Check if there are dampers installed in main ducts and have no
function in balancing air between duct branches such as fire or smoke
dampers), make sure the blades of these dampers parallel to the air flow.
3.15 The preferred method of measuring air flow rate is the pitot tube
traverse method. It is extremely important in selecting the location in the
ducts for the pitot measurement. If packaged air flow measuring stations are
specified and installed, they should be used after a preliminary check of its
performance. Use SE-9 or -10 for air velocity measurement and SE-12 for
volume air flow rate from EXHIBIT 2B, Chapter 2.
4. Instrumentation.
4.1 Make sure that all instrumentation are in good working orders and
are in calibration. See Chapter 2 BASIC MEASUREMENT for calibration of
instruments

by the contractor or equipment manufacturers may be used for performance
tests, if they meet the accuracy and calibration requirements of this Section.
4.3.1
The glass thermometers installed on water pipes for maintenance purposes do
not usually meet the requirements for performance tests.

Temperature.
4. 3. 1.1 Entering and leaving water temperature of water

coils, and entering and leaving hot water of hot water humidifiers. The
4. 3. 1.2 Direct measurement of temperature differential of

entering and leaving water for the applications of paragraph 4. 3. 1.1 above.
For calculating coil energy amount, this measurement is preferred than
deducing the difference from separate temperature measurements of entering and
leaving water. The measurement error shall not exceed +/- 0.1 °C (0.2 °F) .
4. 3. 1.3 Steam temperature of steam coils and steam

humidifiers. The measurement error shall not exceed +/- 0.6 °C (1 °F) .
Locate sensing device after steam control valves.
4. 3. 1.4 Condensate temperature of steam coil. The

measurement error shall not exceed +/- 0.6 °C (1 °F) Locate sensing element
.
after traps. If coils are individually trapped, temperature sensing device

should be in the combined condensate pipe.
Page 151
4. 3. 1.4 Entering and leaving air temperature of coils and

humidifiers. The measurement error shall not exceed +/* 0.28 °C (0.5 °F) .
Stratification is a common phenomenon in air measurement. Since both the flow

rate and temperature distribution may vary across the coils or air plenums, it
is important to obtain the flow rate weighted average temperature of the flow.
At least one measurement at each one square foot of coil face area or plenum
cross-sectional area shall be taken unless the measurement is for outside air
or the measurement is taken in a thoroughly mixed air stream.
1.6
Direct measurement of temperature differential of
4. 3. 1.5
entering and leaving air. For calculating energy amount, this measurement is
preferred than deducing the difference from separate temperature measurements
of entering and leaving air in applications of measuring air temperature
differentials. The measurement error shall not exceed +/- 0.28 °C (0.5 °F)
Precautions for measurements described in the previous paragraph must be
observed.
4. 3. Entering and leaving air relative humidity, wet

bulb temperature, or dew point temperature for cooling coils and humidifiers.
The measurement error shall not exceed +/- 0.6 °C (1 °F) wet bulb or
equivalent. The humidity conditions before and after a coil may also be
stratified. With certain instruments such as sling psychrometers it is
difficult to make multiple measurements across the face of the coil.
Locations away from coils should be selected for single humidity measurements.
If digital electronic hygrometers are used, they should be calibrated against
a sling psychrometer in the field.
4.3.2 Flow rate. Water or steam flow rates for coils or

humidifiers. The total error of combined sensing and readout devices shall
not exceed +/- 3% of specified flow rates. The minimum pipe length
requirements must be observed or flow straightener installed in accordance
with the recommendations of Chapter 2, BASIC MEASUREMENT.
4.3.3 Pressure.
4. 3. 3.1 Steam pressure. The total measurement system error

shall not exceed +/- 3448 Pa (0.5 psi) Steam pressure shall be measured
after steam control valve.
4. 3. 3. Pressure gages installed on pipes for the purpose

of maintenance operation may be used to measure the water pressure at inlet
and outlet of coils if they are calibrated and meet accuracy requirements. The
measurement error shall not exceed +/- 3448 Pa (0.5 psig)
4. 3. 3. Air static pressure and total pressure measurement.

The total measurement system error shall not exceed +/- 12.4 Pa (0.05 in. of
water)
Page 152
.

4.4
Instrumentation calibration test work sheet for air handling

systems, WS 5B-1, is included in the appendix.
5.1
5. Air handling unit component tests.

Fan performance test. The total air flow rate of a system must be
measured and verified to meet specifications first before all other
measurements. Additionally, air distribution to individual outlets must also
be measured and verified as outlined in Setions 5.1.9 and 5.1.10.
5.1.1 Project specification for fans are usually given in flow

rate and static pressures pairs. The flow rates are the actually required air
quantities. The pressure requirements are only estimates. After a
construction project is balanced by the air balancing contractor, the system
should provide the specified flow rates at the finally adjusted fan pressure.
This pressure in most cases may be different from the specified rates.
5.1.2 When fans are tested and rated in the laboratories, they
are tested under ideal inlet and outlet conditions as prescribed in the ASHRAE
(and AMCA) standards. In overwhelming cases of actual installations, the site
conditions of ducts (also called system effect factors) alter the fan
performance, sometimes substantially. The fan manufacturers base their
submittals on matching the performance of the laboratory (or allowed
equivalent) results (fan curves or tables) with estimated air friction (the
specified pressure head) Any mismatch between the laboratory performance and
.
the actual performance is corrected by adjusting and balancing of the entire

air system. Therefore, during commissioning process it is important that a)
the measured fan air flow rates satisfies the specified fan air flow rates; b)
all spaces receive their required air flow rates; and c) the measured fan
pressure heads not necessary equal the specified fan pressure heads.
5.1.3 There is no fixed rules which can be applied universally in

selection of measurement methods in determining air flow rates of fans. The
persons responsible for functional performance tests must use their judgement
in deciding the method or combination of methods for performing the test.
5.1.4 Using Pitot tube to traverse the main ducts of the air
handling unit5.1.6
is the preferred method. Make sure the air flow at the location
of measurement is steady (after minimum length of straight duct run or after
straightening vanes). See EXHIBIT 2-C, STP-5 for measurement procedures.
5.1.5 Measuring air flow rates at coil face or air filter face
with anemometer may be used for supply fan measurement, if good locations for
pitot measurement can not be found. See EXHIBIT 2-C, STP-6 for measurement
procedures
Because of possible external and internal disturbances, air

flow rate, pressure, electric current rate, power consumption, and fan speed
Page 153
measurements shall be repeated 3 times and the results averaged to represent

the fan performance
5.1.7 Required measurement data:
5. 1.7.1 Total air flow rate, Q, in m 3 /s (ft 3 /min)
5. 1.7. 2 Depending on ductwork arrangement of the air

handling unit (lacking inlet or outlet duct) the pressure measurement are
,
different. Consult EXHIBIT 2-B STANDARD EQUATIONS FOR CALCULATIONS for

measurement requirements of different duct systems. The majority of
installations have inlet and outlet ducts (or plenums) for fans. The
following pressures, all in units of Pa (in. of water), should be measured.
* Total pressure at fan inlet duct, P tin
* Total pressure at fan outlet duct, P tout
* Static pressure at fan inlet duct • Psin
* Static pressure at fan outlet duct, P sout
* Velocity pressure at fan inlet duct, Pvin
* Velocity pressure at fan outlet duct, P vout
* Barometric pressure.
5. 1.7. Voltage of electrical service, V
5. 1.7. Electric current, A
5. 1.7. Rotating speed of fan, rpm
5.1.8 It is the responsibility of the construction contractor to

provide a fan to meet the construction specifications and to adjust and
balance the entire air system. The entire air system must operate stably.
During functional performance testing the commissioning team should make sure
that the system stability is achieved by measuring the fan speed. Use a
tachometer or stroboscope (see EXHIBIT 2 -A COMMONLY USED FIELD TEST
INSTRUMENTS) to measure the fan speed continuously for at least 3 minutes. The
speed variation shall not exceed 3% of the run.
5.1.9 Test procedures for constant air volume systems.
5. 1.9.1 Set the outside air damper at the minimum position

and the return air and relief air dampers at their appropriate positions.
Disable damper automatic controls during test. (See Section 7 for testing of
outside air damper settings).
Page 154
... 6
5
2
5. 1.9. Perform the required measurements listed in 5.1.7

above
5. 1.9. 3 Check air flow rates to individual spaces. Select

air outlets randomly throughout the entire duct system from the same air
handling unit. If 10% of the outlets checked is off for more than 10% of the
specified flow rates, a second set of 10% outlets shall be checked. The
entire air distribution system, including fans and all dampers, must be
rebalanced and testing repeated, if (i) any 10% of the outlets checked have
flow rates off +/- 15% from the specified flow rates; or (ii) the total of all
measured flow rates of these outlets is off +/- 10% from the total of the
design flow rates of the same outlets.
5. 1.9. 4 Set the outside air to 100% and other dampers

(return and relief dampers) to their appropriate positions.
5. 1.9. Measure electric current rate. The motor current

rate must not be greater than the full load current shown on the motor mane
plate
5. 1.9. Restore all damper controls.
5.1.10 Test procedures for variable air volume (VAV) systems.
5.1.10.1 It is difficult, if not impossible, to know when

the system block loads occur. Fans of variable air systems can only be tested
to verify their capacities and energy rates in accordance to the specified
values despite that the pressure requirements are only estimated.
5.1.10.3
5.1.10.2 Set the outside air damper at 100% position and
the return air and relief air dampers at their appropriate positions. Disable
damper automatic controls during test.
Manipulate duct pressure sensors by applying

simulated pressure changes (thus change the fan curves on a volume -pressure
diagram) and manipulate the air volume controls of the first few air outlets
(thus change the system curves of the volume -pressure diagram). The contract
specified fan duty point (volume flow rate and pressure) may be obtained
during test. Repeated adjustment and measurement may be needed.
5.1.10.6
5.1.10.4 Perform the required measurements listed in 5.1.7
above
5.1.10.5 The electric current rate of the motor shall not

be higher than the name plate full load current.
Use similar procedures test variable air volume

return air fans.
Page 155
5.1.10.7 Restore all damper controls.
5.1.10.8 Randomly select a minimum of 10% of VAV units

which are supplied from the same air handling system. Measure the maximum and
the minimum supply air flow rates of these units by manipulating their
respective thermostats. If 10% of the selected units having their flow rates
(maximum and minimum) differ more than 10% of the specified flow rates, a
second set of 10% units should be selected and measured. The entire air
system must be rebalance and testing repeated, if (i) any 10% of the units
measured have flow rates off +/- 15% from the specified flow rates; or (ii)
the total of all measured flow rates of the selected VAV units differs over
+/- 10% from the total of the design flow rates of the same units.
5.1.10.9 During the maximum and the minimum air flow rate
manipulation, verify the operation sequence of reheat coils (for units with
reheat coils), recirculating fans (for units with recirculating fans), and
other operational controls as required in the contract specifications.
5.1.10.10 Measure and verify the required duct static

pressure at the locations of each fan static pressure sensor.
5.1.10.11 Measure static pressure of at least 25% of all

branch ducts just before the last VAV unit of the branch to verify that the
pressure is within + 49.8 Pa (0.2" of water) of the specified minimum pressure
5.2
of the VAV units. If the static pressure is lower than the minimum pressure
required or more than the total of minimum pressure plus 49.8 Pa (0.2" of
5.1.11
water) the fan static pressure controller setting must be adjusted and duct
pressure retested. The selection the these 25% branches should be estimated
and judged by the Team that these branches may encounter extreme (high or low)
pressure during building load changes.
Test work sheet for fan is included in sheets for air

handling system component tests, 5B-2, in the appendix.
Heating and cooling coils.
5.2.1 Coil measurements should be performed after fan

measurements
5.2.2 Depending on the weather at the time of testing, false

cooling or heating loads may be needed to achieve the contract specified
entering air conditions. If false loads are not available at the time of
commissioning, the heating and cooling coil tests must be postponed till the
specified conditions may be maintained.
5.2.3 Test procedures for water and steam coils.
5. 2. 3.1 Measure air flow rate through coils. See

paragraphs 5.1.4, 5.1.5, and 5.1.6 above for measurement details. For systems
Page 156
. 4
6
9
7
5
2
3
having the same air flow rates through fans and coils, the measured air flow
rates through fans shall be used for coils.
Measure water flow rate of water coils. Adjust

5. 2. 3.
balancing devices, if necessary, to within 3% of the contract specified flow
rate. This water flow rate shall be maintained during the test.
5. 2. 3. Measure entering water temperature of water coil.

Adjust, if necessary, to within 0.6 °C (1 °F) from the contract specified
temperature. This temperature shall be maintained within 0.3 °C (0.5 °F)
during the test.
5. 2. 3. Measure steam pressure and temperature for steam

coils. Check pressure and temperature against steam table to make sure that
steam is at least saturated and that the steam pressure after control valve is
at the specified pressure of the coil. If the indicated pressure is more than
+/- 6.895 kPa (1 psi) from that specified, the steam line pressure controlling
device must be adjusted. If the steam is less than saturated, it must be
brought to saturation conditions before test is continued. The pressure and
temperature of the steam shall be maintained during the test.
5. 2. 3. Measure steam flow rate to the coils. Adjust

manual or automatic valve, if necessary, to within 3% of the contract
specified flow rate. This flow rate shall be maintained during the test.
5. 2. 3. In order to maintain the water entering temperature

and flow rate, or the steam conditions and flow rate, the automatic controls
of the tested coils should be disabled during the test after first verifying
the status (N.O. or N.C.) of the valve/damper actuator.
5. 2. 3. Measure entering air dry bulb temperature.

Temperature control of the air upstream of the coil may need to be adjusted or
false load varied to maintain this temperature within 0.6 °C (1 °F) of the
contract specified entering air dry bulb temperature. For cooling coil, the
adjustment of upstream air temperature may need be performed in conjunction
with adjustment of upstream air humidity (see the following) paragraph.
5.2. 3.8 For cooling coil test, measure the entering air
humidity (relative humidity, wet bulb temperature, or dew point temperature).
Usually humidity needs to be added in the air by manipulating humidifier or
false humidity load source. The humidity must be maintained within 3% RH or
equivalent of the contract specified value.
5. 2. 3. Run the air handling unit for at least 10 minutes

to prove that the system is under steady state conditions. Steady state
condition is achieved when the average of three consecutive measurements of
coil leaving air temperature, at 5 minute intervals, do not differ by more
than 1.1 °C (2 °F)
Page 157
5.2.3.10 Measure barometric pressure.
5.2.3.11 Measure coil leaving water temperature.
5.2.3.12 Measure Water pressure at coil inlet and outlet of

water coils.
5.2.3.13 Measure air static pressure at upstream and

downstream air of coils.
5.2.3.14 Take three sets of air data at 5 minute intervals:
* Entering air dry bulb temperature.
* Leaving air dry bulb temperature.
* Entering air relative humidity, wet bulb temperature, or

dew point (for cooling coils only).
* Leaving air relative humidity, wet bulb temperature, or

dew point temperature (for cooling coil only).
5.2.4 Separate test work sheets for heating coil and cooling coil
are included in test work sheets for air handling system component tests, WS
5B-2, in the appendix.
5.3 Humidifiers.
5.3.1 Numerous types of humidifiers are being used in different

applications. The test procedures described in this section applies to
humidifiers which discharge steam directly into the air stream.
5.3.2 Humidifiers should be tested after fan and coil tests to

assure that the capacities of the fan and coil which affect the performance of
the humidifier meet the contract specification.
5.3.3 The test may be performed at any entering air temperature.

The commissioning team should be sure that the air leaving the humidifier
section do not reach 80% RH.
5.3.4 Test procedures.
5. 3. 4.1 Measure air flow rate through the humidifier

section of the unit. See paragraphs 5.1.4, 5.1.5, and 5.1.6 above for
measurement details.
5. 3. 4. Measure steam pressure and temperature at steam

supply pipe. Check steam tables to make sure that steam is at least saturated
and that the steam pressure is at the specified pressure. If the indicated
Page 158
. . 4
3
5
6
pressure is more than +/- 6.895 kPa (1 psi) from that specified, the steam
line pressure controlling device must be adjusted. Correct the degree of
steam saturation, if the steam is less than saturated, before proceeding
testing. The steam pressure shall be maintained during the test.
5. 3.4. Adjust humidifier controls to full capacities.

Maintain full capacity during the test.
5. 3. 4. Let system run for at least 10 minutes.
5. 3. 4. Take three sets of air data at 5 minute intervals:

dew point temperature.
* Leaving air, relative humidity, wet bulb temperature, or

dew point.
5. 3. 4. Observe the humidifier operation. There should not

be "spitting" of water.
5.3.5 Test work sheet for humidifier is included in test work

sheets for air handling system component tests, WS 5B-2, in the appendix.
5.4 Air filter.
5.4.1 It is not feasible to test air filter efficiencies and dust

holding capacities in the field. They must be tested in the laboratories in
according with industry standards. See construction specifications.
5.4.2 For operational testing of air filters see EXHIBIT 5-A,

INSPECTION PROCEDURES FOR AIR HANDLING SYSTEMS.
6. Calculation and evaluation of performance of air handling

components
6 . 1 Fans
6.1.1 The measured total air flow rate of the fan must be within
5% of the specified fan air flow rate. The motor current rate must not be
greater than the full load current shown on the motor mane plate.
6.1.2 Calculate the fan total pressure or fan static pressure

from pressure measurements. For the reasons stated in paragraphs 5.1 above,
Page 159
this pressure should be used for reference only, if the other data show that
the fan performance
6.1.3 is satisfied.
Air flow rates in construction documents and manufacturer's

literature are usually given in standard air conditions. Designers usually do
not adjust air properties for HVAC applications below 610 m (2000 ft)
altitude. Therefore no correction to measured data is required for ordinary
heating and cooling applications below this altitude. For applications above
2000 ft, the commissioning team should be careful in determining the basis of
6.2
air flow rates as required in the construction documents. The Team should
make sure that the measured data and the required rating are on the same
basis. For adjusting of air properties at higher altitudes, see EXHIBIT 2-B
STANDARD EQUATIONS FOR CALCULATIONS.
Heating and cooling coils.
6.2.1 For heating coils the entering and the leaving air humidity
are not required to be measured in this guide. The errors of the enthalpy of
air caused by this simplification are not significant if a 50% RH coil
entering air humidity is assumed. This assumption is justified for the
majority of HVAC applications.
6.2.2 The construction documents should state the basis of coil

capacity. If the basis of volumetric airflow rates are not stated, assume
they are for standard air.
6.2.3 Calculation procedure. The three sets of measured data

shall be separately calculated to get the coil capacity. Each set of data is
calculated as follows.
6. 2. 3.1 Calculate the saturated water pressure of the

entering air, (P sw ) en t* kPa n °f Hg)
(i- -
,
knowing the entering air dry bulb
temperature, using SE-1.
6. 2. 3. Calculate the entering air vapor pressure, (Pw ) ent .
kPa (in. of Hg) knowing the measured humidity of entering air for cooling
coil or the assumed humidity (50% RH) of the heating coil, using SE-2.
6. 2. 3. Calculate humidity ratio of entering air, (W) ent ,
kg (in) of vapor/kg (lb) of dry air, using SE-3.
6. 2. 3. Calculate enthalpy of entering air, (H) ent ,

kJ/kg
(Btu/lb) of air, using SE-4.
6. 2. 3. Calculate enthalpy of leaving air, (H) lvg kJ/kg ,
(Btu/lb) of air), using SE-4. For cooling coil both the dry bulb temperature
and humidity are as measured. For heating coil assume the leaving air has the
same humidity ratio as the entering air (calculated in 6. 2. 3. above).
Page 160
, . . , 6
9
7 ,
3
Calculate specific volume of air, v, m /kg (ft 3 /lb)
6. 2. 3.
of air), using SE-5. The air temperature at the flow measurement location
must be used in this calculation.
6. 2. 3. Calculate mass flow rate of air, M kg/s (lb/min)

3
using SE-14. The measured volume air flow rate, Q, m 3 /s (ft /min) is needed ,
in the calculation.
6.2. 3.8 Calculate heating or cooling capacity of coil.
Capacity, W (Btu/h)
- M [
(H) lvg - (H) ent (For SI)
- 60 M [(H) lvg - (H) ent ]

(For Customary)
6.2.4
6. 2. 3. Calculate net water pressure drop of water coils.
6.2.3.10 Calculate net air friction across coils for coils.

6.2.5
The average of three calculated coil capacities shall not
be less than 95% of the contract specified capacity if no tolerance is
6.3
specified. Check project specifications for specified commissioning
tolerances 6.2.6
The test water coil water pressure drop shall not be

greater than 110% of the contract specified pressure drop if no tolerance is
specified
The test air friction of coil shall not be greater than

110% of the contract specified air friction if no tolerance is specified.
Humidifiers.
6.3.1 Calculate the average entering air and the average leaving
air dry bulb temperature from measured data.
6.3.4
6.3.2 Calculate the average relative humidity, wet bulb
temperature, or dew point temperature of the entering and the leaving air from
measured data.
6.3.3 Calculate the saturated water pressure of the entering air,

( ?sw) ent *
Fa (in. of Hg) knowing the entering air dry bulb temperature, using
SE-1.
Calculate the entering air vapor pressure, (Pw ) ent ,

Pa (in.
of Hg) knowing the measured humidity, using SE-2.
Page 161
6.3.5 Calculate humidity ratio of entering air, (W) ent ,

kg (lb)
of vapor/kg (lb of dry air, using SE-3.
6.3.6 Calculate the saturated water pressure of the leaving air,

( p sw)iv 8 .
Pa (in* °f Hg) knowing the leaving air dry bulb temperature, using
SE-1.
6.3.7 Calculate the leaving air vapor pressure, (P w )ivg ,

Pa (in.
of Hg) ,
knowing the measured humidity, using SE-2.
6.3.8 Calculate humidity ratio of leaving air, (W) lvg ,

kg (lb) of
vapor/kg (lb) of dry air, using SE-3.
6.3.9 Calculate specific volume of air, v m 3 /kg (ft 3 /lb) using ,
SE-5. The air temperature at the flow measurement location must be used in
this calculation.
6.3.10 Calculate mass flow rate of air, M, kg/s (Ib/min) using ,
SE-14. The measured volume air flow rate, Q, m 3 (ft 3 /min), is needed in the
calculation.
6.3.11 Calculate humidifier capacity.
Capacity, kg/s (lb/h)
- M [(W) lvg - (W) ent ]

(For SI)
“ 60 M [(W) lvg - (W) ent ]

(For Customary)
6.3.12 The above calculated humidifier capacity shall not be less

than 95% of the contract specified capacity if no tolerance is specified.
6.3.13 The humidifier shall not "spitting".
7. Air handling system operational tests.
7.1 System operations of air handling systems are very much

individualized depending on the system design and control arrangements. The
following operational test procedures are given for commonly used systems and
control schemes. The commissioning team should review construction documents
and contractor's submittals carefully before testing. The Team should
emphasize on functional compliance to contract documents. Although some test
work sheets are attached in the appendix for field use, the commissioning team
may fine it necessary to develop its own test work sheets following similar
format given.
Page 162
4
6
5
2
3 8

7.2
During testing of control operations pay special attention to

sequencing of controlled devices (coil valves, damper motors, etc.). Make
sure they are not overlapped to cause wasting of energy over the entire
operating range.
7.3 Observe the operation of controlled devices for hunting.

Controller set points must be varied to set the controlled devices in
operation for observation of unstable operation.
7.4 Checking of minimum outside air damper setting.
7.4.1 In most installations, locations for good measurement of

outside air by pitot tube or anemometer are often difficult to find. The
return air duct openings and the outside air louvers and dampers usually
generate turbulence in the outside air stream. If direct measurement of
outside air quantity is not feasible, air mixing method may be used.
7.4.2 Air mixing measurement procedure.
7. 4. 2.1 Turn off all heating coil, cooling coil, and

humidifier of the unit (see paragraph 7. 4. 2. below for exceptions) to
minimize the influence of air temperature change. If the outdoor temperature
is below freezing, be careful to protect coils from freezing.
7. 4. 2. Disengage economy control.
7. 4. 2. Make sure the maximum outside air damper is fully

closed for systems having separate minimum and maximum outside air dampers.
For systems having only one set of outside air dampers the outside air damper
should be at its minimum outside air position.
7. 4. 2. Measure the return air temperature and humidity in

the return air duct. If return fan is installed in the system, this
measurement is done between the return air fan and the air handling unit.
Measurement location should not be too distant from the unit.
7. 4. 2. Measure the outside air temperature and humidity at

a location not too distant from the outside air intake.
7. 4. 2. Measure the mixed air temperature and humidity.

Air stratification is usually a problem in making these measurements. If the
coils and humidifier are valved off, this temperature may be taken at any
location before the supply air fan, such as after the air filters, the heating
coils or the cooling coils. The farthest point from the air mixing chamber is
the preferred location. If the coils and humidifier are not turned off, the
only location for this measurement is at the main air filter bank. At either
the air filter or the coil bank, the entire face of the filters or coils must
be divided into one square foot grids for temperature readings and two equal
Page 163
side-by-side areas for humidity readings. The mixing temperature and humidity
are the algebraic averages of their respective readings.
7. 4. 2. Calculate the outside air quantity by the formula:
Hm - Hr
outside air Q c -= Qs
H0 - Hr
3 3
where Q 0 = minimum outside air quantity, m /s (ft /min)
Q s = supply air quantity measured during component
tests, m 3 /s (ft 3 /min)
Hnj *= average mixed air enthalpy, kJ/kg (Btu/lb) of air
H r *= return air enthalpy, kJ/kg (Btu/lb) of air
H 0 *= outside air enthalpy, kJ/kg (Btu/lb) of air
See paragraph 6.3 for calculation procedures of enthalpy.
7. 4. 2. Since the differences of two enthalpies are used in

the calculations, it is extremely important that the temperature and humidity
measurements be performed accurately. The accuracy of this test may be
increased by increasing the difference of enthalpies between outside air and
return air. Operating appropriate coil of the air handling unit may achieve
this goal. For example, increasing return air temperature by operating reheat
coils or space heating during cool weather will increase accuracy. However,
this approach must be weighed against measurement difficulties stated in
paragraph 7. 4. 2.1 above. If the temperature difference between the outside
air and return air is less than 8.3 °C (15 °F) the test should be postponed.
In performing temperature and humidity measurements same instruments must be
used for all three measurements.
7.4.3 Test work sheet for checking outside air damper setting is
included in test work sheets for air handling system control operation tests,
WS 5B-3, in the appendix.
7.5 Economy cycle controls.
7.5.1 There are different versions of economy cycles. The

commissioning team should review the contract specifications and be familiar
with the ones being applied in the subject units. The following procedures
are used as examples of some economy cycles. They may need to be modified to
suit a particular economy cycle.
7.5.2 Test procedures for dry bulb economy cycle.
7. 5. 2.1 Determine from the project documents and the

automatic temperature control submittals the following temperature: the
change-over temperature above which the system admits minimum outside air
only; the upper and the lower temperatures enclosing the region where the
Page 164
. . . 4
2
6
8
3
7
5
system admits 100% outside air; and the temperature below which the preheater
valve opens
7 .5.2.2 On a psychometric chart plot the three dry-bulb

lines of paragraph 7. 5. 2.1, dividing the chart into 4 regions: minimum outside
air with cooling valve on, 100% outside air with cooling valve on, outside air
and return air dampers modulating with cooling valve off, and minimum outside
air only with preheater valve on. Some design of dry-bulb economy cycle use
only two dry-bulb lines and 3 regions: minimum outside air with cooling valve
on, outside and return air dampers modulating with cooling valve off, and
minimum outside air only with preheater valve on.
If an outdoor air sensor is installed as the

7. 5. 2.
change-over temperature sensor, use STP-1 to simulate the outdoor temperature.
The simulator will be manipulated to vary the air damper and coil valve
operation.
7. 5. 2. Use a temperature simulator to simulate the mixed

air temperature sensor (STP-1). This temperature simulator will also be
manipulated to vary the air damper and coil valve operation.
7. 5. 2. Observe damper and valve operations while

manipulate the two temperature simulators. They should agree with the
psychrometric chart regions. Actual operation of physical movement and
positioning of dampers must be observed. These movements may be compared to
pneumatic or electrical signal to the actuators, but the output readings (gage
or meter) should be used only after verifying the meter or gage readings
accurately indicate actual valve or damper position.
7. 5. 2. Simulate outdoor temperature at different regions

of the psychrometric chart, especially at both sides of the region dividing
lines
7. 5. 2. The change-over temperature test shall be repeated

for "specified change-over temperature plus 2.8 °C (5 °F) " and "specified
change-over temperature minus 2.8 °C (5 °F)".
7. 5. 2. Record the test results, remove the temperature

simulators, and restore the temperature sensors.
7.5.3 Test procedure for enthalpy economy cycle.
7. 5. 3.1 Replace the two temperature and two humidity

sensors of the economy control with temperature and humidity simulators (STP-1
and STP-2)
7. 5. 3. Measure the supply air temperature at the supply

air fan discharge.
Page 165
7. 5. 3. 3 Divide a psychometric chart into 4 regions by

plotting: a) a constant enthalpy line from the saturation line to the space
condition and from this state to the zero -humidity ratio line along a constant
dry-bulb temperature line; b) a constant dry-bulb line through the measured
supply air temperature; and c) a dry-bulb temperature line below which the
system should admit only the minimum outside air (determined from the project
documents). The regions having higher enthalpy and dry-bulb air temperature
than the space air state should admit minimum outside air only. The region
enclosed by this region and the cooling coil discharge dry-bulb line should
admit 100% outside air. The region between the cooling coil discharge air
dry -bulb line and the minimum outside air line should vary outside air amount
by sensing the mixed air temperature. And the region below the minimum outside
air line should admit only the minimum outside air.
7. 5. 3. Manipulate the outside air temperature and humidity

simulators in each of these four regions and observe the outside air dampers,
preheater valves, and cooling coil valves. Special attention should be paid
to the immediate areas at both sides of the region dividing lines.
7. 5. 3. Record the test results, disconnect the temperature

and humidity simulators, and restore the sensor connections.
7.5.4 Because of the diversity of economy cycle controls, work

sheets are not provided. Make test work sheets to suit the control
specifications of the unit.
7.6 Warm-up/cool-down cycle.
7.6.1 For systems having automatic shutdown during unoccupied

hours, they may have warm-up and cool down cycles together with unoccupied
temperature setback or setup. These systems usually require the outside air
dampers closed during the starting up time (from the time of turning on the
systems to the time of scheduled occupancy time)
7.6.2 At the time of this test the air handling systems are most
likely to be in occupied mode. It is necessary to test the sequence of
controls of shutting- down, outside air damper operation, unoccupied
temperature maintenance, and starting-up.
7.6.3 The following is the test procedure for one possible

control sequence.
7. 6. 3.1 Install temperature simulators in place of occupied

and unoccupied temperature controllers (STP-1) and manipulate unoccupied
temperature simulator not to interfere with the occupied time control.
7. 6. 3. Advance timer just past system-off time.
Page 166
4
6
8
9
53
7
7. 6. 3. Observe system operation and outside air damper

position. Supply fan should be off. Heating and cooling coil valves should be
in their status according to specifications. Outside air dampers should be
closed.
Manipulate unoccupied temperature simulator to

7. 6. 3.
activate the system. The simulated temperature activating the system should
be within 1.1 °C (2 °F) of specified unoccupied temperature. The heating or
cooling coil valve should be open according to specifications. The outside
air damper should remain closed.
7. 6. 3. Manipulate unoccupied temperature simulator to

deactivate the system.
7. 6. 3. Advance timer to just past the warm-up or cool-down

time. The system should be on, if the occupied temperature controller is not
satisfied. Otherwise, the system should remain off. When the system is on
the outside air damper should remain closed.
7. 6. 3. Advance timer to just past the system starting

time. The system should be on and the outside air damper should open.
1.1
7. 6. 3. Restor timer to its correct time.
7. 6. 3. Remove temperature simulator and restore to

original temperature controls.
7.7.1
7.6.4 Testing of warm-up/cool-down cycle is included in
test work sheets for air handling system control operation tests, WS 5B-3, in
the appendix.
7.7 A single controller set at a certain controlled variable to control

a component equipment (such as coil or fan).
Examples:
7. 7. Controller having its temperature sensor located in

heated air stream to control preheat coil.
7. 7. 1.2 Controller having its temperature sensor located in

outside air to control preheat coil.
7. 7. 1.3 Controller having its humidity sensor in humidified

air stream or conditioned space to control humidifier.
7. 7. 1.4 Controller having its temperature sensor in space

or duct to control reheat coil.
Page 167
7. 7. 1.5 Controller having its temperature sensor in air

plenum or duct to control cooling coil.
Controller having its pressure sensor or

7. 7. 1.6
differential pressure sensor in air duct to control variable speed fan or
damper for variable volume air system.
7.7.2 These controllers may have second sensors (called

overriding sensors in this test procedure) set at another level of the
controlled variable to override or limit the first sensors' signals.
7.7.3 Test procedure:
7. 7. 3.1 Use a simulated sensor (temperature, humidity,

pressure, etc.) to simulate the controller sensor (STP-1, 2, or 3).
7. 7. 3. Use a second simulated sensor to simulate the

overriding sensor (STP-1, 2, or 3) if the overriding sensor is specified.
7. 7. 3. Determine from the project documents and submittals

the respective set points of the sensor and overriding sensor.
7. 7. 3. Set the simulated overriding sensor in such a level

that it allows the simulated sensor to control the equipment.
7. 7. 3. Manipulate the simulated sensor output and observe

the action of the controlled device. The actions of the controlled device
should be in agreement with the controller's differential or throttling range.
7. 7. 3. While the controlled device is operating in its

operating range vary the overriding sensor beyond its specified limit and
observe the action change of the controlled device.
7. 7. 3. Remove the temperature simulator and restore the

temperature sensor.
7.7.4 Testing of single controller operation is included in test

work sheets for air handling system control operation tests, WS 5B-3, in the
appendix
7.8 A controller having a second sensor (reset sensor) to reset the

control point or a second controller resets the first controller.
7.8.1 Examples:
7. 8. 1.1 Discharge air temperature of a dual duct heating

coil reset by outside air.
Page 168
. .. 4
2
2
5
3 .
7. 8. 1.2 Discharge air temperature of main cooling coil

reset by outside air.
7. 8. 1.3 Varying space humidity in accordance to outside

temperature to avoid condensation.
7.8.2 test procedure:
7. 8. 2.1 Determine from the project document and the

submittals the controlled variable reset schedule (the relationship between
the reset index and the controlled variable)
7. 8. 2. Disconnect both reset and primary sensors from the

controller (or controllers) and connect two simulators in their place (STP-1,
2, or 3). Instead of temperature, humidity, or duct pressure, the simulator
indicates pneumatic pressure, electric resistance, or electric voltage.
7. 8. 2. Manipulate both simulators in accordance to the

contract specified or submittal reset schedule. The action of the controlled
device should agree with the schedule. Pay special attention to the end
points (high and low) of the schedule.
7. 8. 2. Plot the reset schedule from test results and

compare with the specified schedule.
7. 8. 2.1
2. Restore sensors.
7.9.1
7.8.3 Testing the operation of a controller resetting by a second
sensor or by another controller is included in test work sheets for air
handling system control operation tests, WS 5B-3, in the appendix.
7.9 Using multiple zone sensors to reset air temperature for heating or
cooling 7.9.2
Systems are usually designed that the zone having the

highest load resets the air temperature controller, control signals from each
zone sensors are fed into a device (called selector or discriminator) to pick
the most desired signal and this signal is used to reset the air temperature
controller
Test procedure:
7. 9. Determine from the project document and the

submittals the controlled variable reset schedule (the relationship between
the reset index and the controlled variable) and the zones which may reset the
controller
7. 9. 2. Disconnect the primary sensor from the controller

and connect a simulator in its place (STP-1, 2, or 3). Instead of
Page 169
temperature, the simulator indicates pneumatic pressure, electric resistance,

or electric voltage.
7. 9. 2. Disconnect the first zone sensor and connect a

simulator in its place (STP-1, 2, OR 3).
7. 9. 2. Vary the signal level (increasing or decreasing

depending upon the design of the control system) and observe the output of the
signal selector device. At a certain level of the zone signal it should exert
control of the output of the signal selector.
7. 9. 2. Repeat steps 7. 9. 2. 3 and 7. 9. 2. for other zones to

confirm the control of signal selector output by zone signals.
7. 9. 2. Manipulate both simulators (primary sensor and the

last zone sensor) in accordance to the contract specified or submittal reset
schedule. The action of the controlled device should agree with the schedule.
Pay special attention to the end points (high and low) of the schedule.
1 9 2.1 .Plot the reset schedule from test results and

.
compare with the specified schedule.
7. 9. 2. Restore sensors.
7.9.3 Testing the operation of multiple zone sensors resetting

heating or cooling coil air temperature is included in test work sheets for
air handling system control operation tests, WS 5B-3, in the appendix.
Page 170
CHAPTER 6 BUILDING AUTOMATION SYSTEMS
1. Scope. This chapter provides inspection and testing procedures for

energy monitoring and control system (EMCS). The procedures are applicable to
field inspection and testing of hardware and software of EMCS. Emphasis is
placed on sensor calibration, end-to-end data verification, and verification
of software logic and calculations. The subcontractor supplying and
installing the EMCS should be involved in inspecting and testing of the
systems
a. ANSI Standard C2 - National Electrical Safety Code.
b. ANSI/IEEE Standard C12.1 - Code for Electricity Metering.
c. ANSI/IEEE Standard C57.13 - Instrument Transformers.
d. ANSI Standard X3.4 - National Standard Code of Information Exchange.
e. ANSI Standard X3 64 - Additional Controls for Use with American

.
National Code for Information Interchange.
f. IEEE Standard 142 - Recommended Practice for Grounding of Industrial

and Commercial Power Systems.
g. Military Standard MIL-STD-2202 - EMCS Factory Test Procedures.
h. Military Standard MIL-STD-2203 - EMCS Performance Verification and

Endurance Test Procedures.
i. NFPA Standard 70 - National Electrical Code.
j. ANSI/ASHRAE Standard 114-1986 - EMCS Instrumentation
3. EMCS Inspection.
a. EMCS shall be inspected for construction and installation to meet

safety and functional requirements.
b. See EXHIBIT 6 -A for inspection procedures and Appendix for inspection

check lists.
Page 171
4. EMCS Testing.
a. EMCS shall be tested in the field to meet functional performance
requirements of the contract specifications.
b. Individual testing of component performance is not recommended except

for sensor calibrations.
c. EMCS sensing accuracies from sensors to display must be verified to

meet the specified accuracies.
d. EMCS calculations of sensed variables must be verified to meet the

specified accuracies or generally recognized good engineering practices.
d. EMCS application software must be verified to meet the contract

specification intent. Software to implement specification intent may vary. The
commissioning team must be familiar with the application and revise the
described procedures if necessary.
e. Certain tests of automatic temperature controls which may also apply

to EMCS functions are described in Chapter 5, AIR HANDLING EQUIPMENT AND
SYSTEM. Certain applications of measurement, instrumentation, and
calculations are described in Chapter 2, BASIC MEASUREMENT.
f. See EXHIBIT 6-B for test procedures and Appendix for test work
sheets
Page 172
EXHIBIT 6-A INSPECTION PROCEDURES FOR BUILDING AUTOMATION SYSTEM

(BAS)

energy monitoring and control systems (EMCS). Certain inspection of localized
automatic temperature controls for air handling systems which may also apply
to the EMCS are described in EXHIBIT 5-A, INSPECTION PROCEDURES FOR AIR
HANDLING SYSTEMS. Certain application precautions of measurement
instrumentation are described in CHAPTER 2, BASIC MEASUREMENT.
a. ANSI Standard C-2 (National Electrical Safety Code) states rules for
practical safeguarding of persons during installation, operation, or
maintenance of electric supply and communication lines and their associated
equipment which are used in buildings as a utility. Included, among others,
are electric supply, telephone, data, fire, and police alarm lines and
equipment
b. IEEE Standard 142 (Recommended Practice for Grounding of Industrial

and Commercial Power Systems) describes practices and methods of grounding
electric systems and equipment. Included are electric system grounding,
equipment grounding, static and lightening grounding, and methods of
connection to earth.
c. NFPA Standard 70 (National Electrical Code) describes provisions for

safeguarding of persons and property from electricity hazards. This code
covers installation of electric conductors and equipment related to building
and its occupancy and equipment use. However, it does not cover installation
of communication and electric equipment which are under the exclusive use and
control of communication and electric utilities.
3. Inspection procedures.
3.1 Review contract drawings, specifications, and approved submittals
to become familiar with the requirements.
3.2 If existing equipment and systems are interfaced with the new
system and the specifications require the contractor to test and report the
conditions of the existing equipment and systems, be sure these are performed
before starting commissioning process to minimize future possible disputes.
3.3 Verify delivery of training, operating, and maintenance manuals,

including materials for display such as control diagrams, slides for
Page 173
projectors, dynamic color graphics of screen copy (or photographs of screen),

and source code listing. Manuals must be complete and specifically designed
for the project. Control diagrams must be complete and framed with proper
item identification, understanble sequence description, etc.
3.4 Inspect equipment for completion, including field equipment and

central computer and associated equipment (display, printers, data storage
devices etc )
, .
3.5 Verify equipment models against approved submittals. Verify that

model and serial numbers are provided on major components of equipment.
Inspect that the same type of equipment are produced by the same company.
3.6 Inspect for proper installation and omissions of equipment and

wiring against drawings, specifications and approved submittals. Support
equipment such as PROM programmer, field interface device (FID) /multiplexer
(MUX) portable tester, FID and data environment (DE) simulators, if specified,
must be supplied.
3.7 Check for access spaces and clearance of equipment. Manufacturer's

recommended spaces must be provided.
3.9 Check equipment and wiring for proper grounding. This includes
equipment in the field, central computer equipment, and building facility such
as raised floor and wire troughs. The requirements of equipment grounding are
usually specified in the equipment manufacturer's installation instructions or
in codes listed in Section 2 above and should be shown on installation shop
drawings. The commissioning team should verify actual installation in the
field. Check grounding wire size, installation manner, and insulation
integrity for safety.
3.10 Certain signal wiring requires shielding to minimize interference

from other electromagnetic sources. If shielding is required from
construction documents and shop drawings, verify its existence and grounding
of shielding. Generally shielding should continue to the controller, not just
the cabinet where the controller is located if line voltage wiring exists in
the cabinet. Ground at one end only unless specifically directed otherwise by
control manufacturer.
3.11 Check for proper separation of high and low voltage wires, and
discrete vs analog wiring if applicable.
3.12 Note bare wires where insulation should be provided.
3.13 Verify wiring and terminals are identified as required in

specifications and manufacturer's instructions. Check inside control panels:
everything labeled correctly, installed neatly, settings marked, appropriate
Page 174
last-minute notes attached, and all features as specified.
3.14 Check for completeness of required instrumentation and indicating

devices. For FID's, specifications may require indicating lights for power,
on-line with central control unit (CCU) ,
self test status, FID output
disabling status, etc.
3.15 Verify cabinet type (indoor or outdoor) of FID and MUX.
3.16 Verify the type of locking devices of equipment cabinets for

specifications compliance. Verify that same key fits all locking cabinets.
3.17 Inspect duct integrity at locations of temperature, humidity,

pressure, and flow sensors. Insure that there are no leaks at these locations,
especially when located on suction side of the fan.
3.18 Thoroughly examine details of sensor manufacturer's installation

and maintenance manual for installation precautions to minimize sensing
errors
3.19 Locations of all sensors are important. They must be located at

where the intended measurement of variables can be fully detected.
3.20 Where averaging temperature sensing is needed and/or specified,

multiple sensors or averaging sensor must be provided.
3.21 Temperature sensor supporting rods should be well extended in

fluid stream to minimize conduction error.
3.22 Inspect temperature sensor location foi possible radiation

influence from other equipment. If radiation shield is required, verify its
presence
3.23 Inspect humidity sensor for water protection

.
Most humidity
.
sensors must not be in an environment close to or above saturation. Check air

baffles for salt-phase transition type sensor if applicable.
3.24 Inspect pressure sensor installation. The relative position of

sensing element to stream flow direction is important. Devices to measure
static pressure of the flow fluid must not be influenced by flow velocity. For
steam sensors, verify that the sensing line includes a pigtail to isolate the
steam from the sensor. Verify that the lines are run properly to eliminate any
signal error due to sensing line slope, restrictions, etc.
3.25 Similar to pressure sensing devices, all flow sensing devices are
sensitive to their relative position to fluid flow direction. The sensing
plane of these devices should be inspected in relation to pipe and duct flow
direction.
Page 175
3.26 Flow sensing devices must have minimum pipe length upstream and
downstream according to contract specifications, manufacturer' recommended
lengths, or other recommended practices (see Chapter 2 BASIC MEASUREMENT).
3.27 Sensors installed in chilled water pipes or vessels should have

their support long enough to avoid condensation in electronic parts.
Electrical boxes for electronic parts should be oriented to avoid receiving
condensation.
3.28 Some sensor transmitters may be influenced by high temperature.

Sensor support should be long enough to minimize this effect.
3.29 Inspect mechanism of damper and valve to position sensor. The

position should be responsive to damper and valve movement without slippage.
Check control element (damper blades/linkages) for smooth operation.
3.30 Verify all controls functioning accurately without hunting.
3.31 Verify completion of specified training programs. This may

involve personnel from the building use agency. Contract specifications
should be checked as to the steps and scope of the training.
Page 176
EXHIBIT 6-B TEST PROCEDURES FOR BUILDING AUTOMATION SYSTEM (BAS)
1. Scope. The test procedures described in this EXHIBIT apply to

field test of energy monitoring and control systems (EMCS) Certain test of
.
localized automatic temperature controls which may also apply to the EMCS are
described in EXHIBIT 5-B, TEST PROCEDURES FOR AIR HANDLING SYSTEMS. Certain
application precautions of measurement and instrumentation are described in
Chapter 2, BASIC MEASUREMENT. •
a. Military Standard MIL-STD-2202 (EMCS Factory Test Procedures) presents
guidelines for factory test requirements of EMCS using tri-service EMCS guide
specifications, before the equipment is shipped to the field for installation.
Micro systems are not included.
b. Military Standard MIL-STD-2203 (EMCS Performance Verification and

Endurance Test Procedures) presents guidelines for generic test procedures
designed to assure that EMCS installed using tri-service EMCS guide
specifications meet the specified technical, operational, and performance
requirements
c. ANSI/IEEE Standard C12 1 (Code for Electricity Metering) establishes

.
acceptable performance criteria for ac watthour meters, demand meters, demand

registers, pulse devices, instrument transformers, and their auxiliary
devices. It also includes information such as recommended measurement
standards, installation requirements, test methods, and test schedules of
these equipment.
d. ANSI/IEEE Standard C57.13 (Instrument Transformers) covers certain

electrical, dimensional, and mechanical characteristics and takes into
consideration certain safety features of current and inductively coupled
voltage transformers used in the measurement of electricity and control of
equipment. It may be used as basis for performance, interchangeability,
safety and selection of these transformers.
e. ANSI Standard X3.4 (National Standard Code of Information Interchange)

specifies a set of characters with their coded representation for interchange
of information among data processing systems and associated equipment, and
within data communication equipment. This character set includes control
characters for code extension.
f. ANSI Standard X3 64 (Additional Controls for Use with

.
American National Standard Code for Information Interchange) defines a set of

control functions that augment the set of control functions in the standard of
Page 177
e . above
g. ANSI/ASHRAE 114-1986 (EMCS Instrumentation) deals with accuracy of

instrumentation
3. General.
3.1 The size and configuration of EMCS vary considerably for GSA
managed projects according to the size and complexity of the mechanical
systems, the desire of the owner for system operation, and cost
considerations. Therefore, the commissioning team must review the contract
documents before any attempt to proceed with testing of EMCS.
3.2 Since all projects require submittal approval and most

specifications require factory tests of EMCS equipment before shipping,
commissioning tests should be concentrated on verifying functioning and
performance in the field. If factory testing for components is specified, the
Team should verify the factory test by inspection or obtain proof from the
contractor
3.3 Testing individual performance of EMCS components in the field,

except for sensors, is not included in this guide.
3.4 Essentially field testing is divided into three categories: sensor

calibration; end-to-end (from sensor to readout devices in central control
room) verification of data; and verification of software logic and
calculations
3.5 It is useful, and usually essential, to verify operation of EMCS by

forced failures of primary units.
4. Test procedures.
4.1 Verify calibration of sensors, sensor/transmitters, and
sensor/controllers. This includes temperature, humidity, pressure, flow, and
electricity consumption. See Chapter 2, BASIC MEASUREMENT.
4.2 Test system startup operation.
4.2.1 Before the test make sure all EMCS equipment are off.
4.2.2 Turn on all EMCS equipment.
4.2.3 Initiate computer manufacturer's specified startup

procedures to start computer operation.
Page 178
4.3 Verify the existence of contract specified and/or submittal

approved software by checking file storage of the computer and/or by actual
performance demonstration. Depending on the size and sophistication of the
projects, the following software may be required in the central computers:
4.3.1 Bootstrap program to load and initiate computer and EMCS

operation.
4.3.2 Disk operating system to manage all peripheral devices and

file management.
4.3.3 Editor software to create and modify source codes.
4.3.4 Language processor (compiler or interpreter) to translate

source codes to object codes.
4.3.5 Linking software to create relocatable codes.
4.3.6 Assembler for the assembly language translation.
4.4 After initial bootup, and prior to any further checkout, verify
backup system operations and switchovers including redundant processors,
backup power supplies, battery backed memories, etc. Review manufacturer's
software and functional test procedures which were performed at the
manufacturer's site. (It is important that in the system specification
process a test procedure be requested and that data from that test be
submitted prior to delivery of system.) Verify EMCS command software used by
building operators from operator's console. This may be checked by issuing
commands at the operator's console and observing display, printer output, or
HVAC equipment responses. The following features are usually specified in the
contract specifications and may be verified as outlined.
4.4.1 Software for checking input commands and issuing error

messages. Enter various correct and incorrect commands.
4.4.2 System and point addressing check. Enter command to

display I/O data. Verify all data points which are listed in point directory.
4.4.3 Start-stop or enable-disable of HVAC equipment or EMCS

components (FIDs AND MUXs). Enter commands to start/stop selected HVAC
equipment, and to disable and enable selected FIDs, MUXs, and sensor inputs.
4.4.4 Operator override/automatic mode. Enter command to change

selected automatic control under EMCS to manual and vice versa.
4.4.5 Display format. Enter commands to display data and

graphics on terminal and graphic display. Check display content for adequacy
and clarity as specified.
Page 179
4. A. 6 Ability to modify, cancel and confirm operator's commands.

Verify by entering commands.
4.4.7 Set-point adjustment and limiting. Enter commands to

adjust set points of controllers and range limits of the controlled media.
Verify by display. Also enter commands to adjust set-points outside their
range limits. EMCS should display error messages.
4.4.8 System access and access level control. Try to log on to

system with both incorrect and correct ID codes. Try to enter different
commands with different access level of the operators. The responses of the
EMCS should be as specified.
4.4.9 Start/stop equipment. Enter command to start or stop

selected equipment. Also reset time to initiate automatic mode. Verify
responses by observation of equipment and EMCS display.
4.4.10 Change parameter of points. Enter commands to change

parameters of selected points such as high and low limit alarms, scale factor,
etc. to test the adequacy of software.
4.4.11 Report generating (status, profile, energy, etc.). Enter

commands to generate reports such as all points, trend, total display of a
system, timed display, and other specified reports. Examine the report
content for general format, system/point code, time interval of reporting,
point status/value/unit, energy amount/rate/unit, status of control and set
time (manual or automatic) and other specification required information.
,
Verification of software calculations of various reporting values is outlined

in section 4.5 (Test EMCS overall performance) below.
4.4.13
4.4.12 Check for proper operation of system status reports,
including point status reviews which would include information such as points
currently in alarm, points removed from alarm checking, points off of scan,
etc
Alarm reporting. Initiate alarm conditions of different

points at different alarm levels in sequence to examine alarm reports. The
reports should show alarm location and device, alarm time, cause of alarm,
current status of the point, etc. as required in the specifications. When
alarm conditions are removed the printer should print updated status report.
Also verify audible alarm operations in accordance with specification
requirements. Then initiate alarm conditions at different levels at the same
time to check alarm priority.
4.5 Test EMCS overall performance. These tests verify the overall
accuracy of the EMCS from sensors, signal conditioning, data transmission,
etc., as well as software used for certain calculations.
Page 180
4.5.1 Sensor calibrating instruments should be used in checkout

of the overall performance. The sensors of these instruments should be placed
at the proximity of EMCS sensors to indicate the conditions of the controlled
media (air, water, etc.). A preliminary evaluation should be made as to the
suitability of having the EMCS sensors checked in place or they may be placed
in simulated environment. If the response times of the two sensors (EMCS
sensor and calibration sensor) are similar, it may be performed with the
sensors in place. If the conditions of the controlled media change slowly, it
may also be performed with the sensors in place. However, if the conditions of
the controlled media change rapidly and the time responses of the two sensors
vary considerably, the checkout process should be done with the sensors placed
in a known environment such as a temperature bath.
4.5.2 For EMCS sensors measuring air or water temperature the

checkout may be done with sensors in place, if conditions described in 4.5.1
above are satisfied. Specifications of many projects require that calibration
sensor wells be installed in pipes for in place calibration. If calibration
wells are not installed in pipes, checkout must be done with a temperature
bath.
4.5.3 Ways of communicating (transmitter/receiver, telephone,

etc.) between the sensor locations and EMCS central control room are needed to
coordinate timing and other calibration information.
4.5.4 Checkout procedures for air, steam, and water temperature,

air humidity, air static pressure, and steam pressure with sensors in place.
4.5.4. Place calibration sensor in the controlled medium

(air, water, or steam). Caution should be exercised that EMCS and calibration
sensors do not interfere with each other (such as for temperature or pressure
sensing) and that the calibration sensor does sense the true conditions.
4. 5. 4. Wait sufficient time for the calibration sensor to

stabilize. The time required depends on the time constant and the initial
condition of the sensor.
4. 5.4. Coordinate time between the site and central

control room for taking readings
4. 5. 4. Simultaneously take readings of the calibration

instrument and the EMCS readout terminal.
4. 5. 4. Take at least one more reading for the same sensor.

The range of the two readings taken should be as wide as the HVAC operation
allows, but not more than that called for in the contract specifications. In
order to have the wide range desired the second test may need to be conducted
at a different time from the first test when the HVAC equipment experiences
different loads.
Page 181
4. 5. 4. Compare readings from the calibration instrument

and the EMCS They must be within the accuracy requirements of the contract
.
specifications. The values of certain data need to be calculated before

comparison. These are specifically noted in the following paragraphs.
4.5.5 Checkout procedures for water and steam temperature with

sensors removed from pipes.
4. 5. 5.1 Remove sensor from pipe and place it in a portable

temperature bath.
4. 5. 5. Place calibration sensor in the portable

temperature bath. Since temperature is measured at steady conditions during
this test, there is no need to concern time constant differences of the two
sensors
4. 5. 5. Set bath temperature to around the contract

specified low range of the sensor.
4. 5. 5. Wait sufficient time for sensor temperature to

stabilize
4. 5. 5. Coordinate time between the site and central

control room for taking readings.
4. 5. 5. Simultaneously take readings of the calibration

instrument and the EMCS readout terminal. These readings give the low range
check.
4. 5. 5. Set bath temperature to approximately

three-quarters of the contract specified operation range of the sensor.
4. 5. 5. Repeat steps 4. 5. 5. 4 to 4. 5. 5. to get the high

range data.
4. 5. 5. Compare both low and high readings from the

calibration instrument and the EMCS. They must be within accuracy
requirements of the contract specifications.
4.5.6 Checkout procedures for flow measurement.
4. 5. 6.1 To check flow measurement from end-to-end (from

sensor to readout device) in most cases is difficult. The primary flow sensors
(such as orifice plates, turbine meters, etc.) must be substituted by sensor
simulating instruments which may be manipulated to give known sensing
quantities (such as manometer or pressure calibrator for pressure, count
generator for turbine meter, etc.).
Page 182
4. 5. 6. 2 Remove primary flow sensor from EMCS
4. 5. 6. Connect sensor simulating instrument to EMCS.
4. 5. 6. Manipulate sensor simulating instrument signal to

zero flow signal.
4. 5. 6. Take reading from EMCS readout terminal. This

reading should show zero flow.
4. 5. 6. Manipulate sensor simulating instrument signal to

approximately three-quarters of the high range of the specified flow. Record
this data.
4. 5. 6. Take reading from EMCS readout terminal. This is

the high range data.
4. 5. 6. Calculate manually the theoretical flow rates from

the high simulated data (from differential pressure or counts to flow rate).
4. 5. 6. Compare the manually calculated flow rates (both

zero and high) with the readings from the EMCS readout terminal. They must be
within the accuracy requirements of the contract specifications.
4.5.6.10 Enter a new constant (say approximately 10% more

than the correct constant) in the flow calculation equation of the software.
Use the new constant to recalculate the flow rate manually. The newly
calculated flow rate should be close to the EMCS indicated flow rate within
the specified tolerance.
4.5.7 Check out procedures for enthalpy calculations.
4. 5. 7.1 Set EMCS to report outdoor temperature, humidity,

and enthalpy.
4. 5. 7. Manually calculate enthalpy of the air with one set

of temperature and humidity printout using equations given in EXHIBIT 2-B
4. 5. 7. Simulated signals of temperature and humidity may

also be used to check enthalpy calculations.
4. 5. 7. The difference of the reported enthalpy shall not

differ from that of the calculated by more than 3% or, if specified in the
specifications, shall be within the accuracy stated in the contract
specifications
4.5.8 Checkout procedures for energy calculations. Instantaneous

energy consumption rates and accumulated energy amount are usually included in
Page 183
8.1
reports. They should be verified for correctness.
4. 5. For energy consumption using water as medium,

obtain a set of operating data from EMCS containing flow rate, temperature
differential, and energy amount. Hand calculate energy amount with the flow
rate and temperature differential. Verify the hand calculated amount with the
indicated amount.
4. 5. 8. For energy consumption using steam as medium,

obtain a set of operating data from EMCS containing flow rate, steam pressure,
steam temperature, and condensate temperature. Hand calculate enthalpies of
steam and condensate (using steam tables), and the net energy amount. The
difference between hand calculated and EMCS indicated amounts should be within
the specified tolerance.
4. 5. 8. For energy accumulation calculations, set the

system to print both instantaneous and accumulated energy data for the same
period. The instantaneous data should be printed at very short intervals
within the period to be accumulated. Verify the accumulated data (thus the
accumulation software) by adding the instantaneous energy amount of the entire
period.
4. 5. 8. Verify accumulation data for electric, steam, and

water energy.
4.6 Test EMCS application software. EMCS performance and capabilities

depends upon how application software is written. Although substantial
differences may exist in actual EMCS software being offered today, the
following test procedures are considered suitable for testing typical
requirements. The commissioning team must examine the contract specifications
to be sure what the contract requirements are and compare them with the
details of the contractor' submittals. The test procedures described below do
not check the details of the software, rather, they try to verify the final
output as indicated by the field equipment. Modify the test procedures to
suit particular projects as necessary. Before testing each program the
required input and output of the program and those listed in the contract
specifications should be compared to make sure that the program covers the
specified operations. Verification of HVAC equipment operation (such as
equipment status or temperature of space air) may be done by either (1) actual
observation of equipment status and test instruments, or (2) obtaining EMCS
reports if the accuracy of these reports has been verified previously.
4.6.1 Scheduled start-stop program. To start and stop HVAC

equipment based on predetermined time of the day and day of the week. Some
applications also require time delays for large loads to reduce power surges.
4. 6. 1.1 Verify that input includes start/stop time and days

for specified equipment. Also verify input for time delays of specified
equipment. Check holiday effect.
Page 184
1.2 CHAPTER 6 BUILDING AUTOMATION SYSTEMS
1.3
4. 6. Note from operator's console the status of selected
1.4
equipment which is specified to be on scheduled start-stop program.
4. 6. Enter command to place this equipment under the

program.
4. 6. Observe equipment at the scheduled start- stop time

to verify its operation. Also verify time delay for large loads.
4. 6. 1.5 Start and stop this equipment manually by

overriding the EMCS
4.6.2 control. EMCS should issue alarm for unauthorized action.
4. 6. 1.6 See WS6B-5 for sample test work sheets.
Optimum start-stop program. To start and stop equipment

based on weather and building thermal conditions to optimize equipment running
time
4. 6. 2.1 Verify that the required input includes space

temperature, outdoor temperature, occupied time and days of the week, and the
response time of the air handling equipment, on an individual system by system
basis
4. 6. 2. Enter command to place selected equipment under the

program.
4. 6. 2. At the beginning and the end of the scheduled

occupancy time record the space temperature. These temperatures must not
differ by more than 1.7 °C (3 °F) from the required occupied space
temperature, or, if specified, by an amount greater than the tolerance
specified in original specification.
4. 6. 2. Verify that at the beginning of the occupied time

the air handling system is on and ventilation air is being admitted.
4. 6. 2. Start and stop the equipment manually by overriding

the EMCS control. EMCS should issue alarm for unauthorized action.
4. 6. 2. See WS6B-6 for sample test work sheets.
4.6.3 Duty cycling program. To shut down equipment during

building occupied hours to save energy and reduce demand charge. The cycling
time is varied so that the space conditions will be kept within a
predetermined temperature and relative humidity band. Minimum on-period and
maximum off-period may also be specified.
4.6. 3.1 Input required data. This usually include maximum

and minimum space temperature, and minimum cycling time.
Page 185
4. 6. 3. Enter command to place equipment under duty cycling

control
4 .6. 3. Record space temperature at 5 minute intervals.
4. 6. 3. Verify that the equipment is cycling.
4. 6. 3. Input space temperature at different levels and

verify cycling time change by observation. Contract specified minimum
on-period and maximum off-period must not be violated.
4. 6. 3. Space temperature during duty cycling time must be

4.6.4 and minimum temperature band.
within the maximum
Electrical demand limiting program. This program limits

electric load to below utility company demand schedule by shedding certain
electric loads. The demand charge depends on the method the utility company
uses. Generally, fixed interval metering may shed equipment sequentially or
rotationally The loads which have been shed are restored when the demand
.
becomes lower than a predetermined level. There are many versions of demand
limiting. The commissioning team should be familiar with the demand charge
method and the contract specification requirement of demand limiting.
4.6.4. The contract specification of electrical demand

limiting program may require some of the following input: electric loads
(equipment) under the program, load priority, demand metering interval,
average power during metering interval, delay time, minimum off -time,
minimum- on time, and maximum off- time. The time and days applicable may also
be included. Check to make sure the contractor supplied input list agrees with
required items of the specification.
4. 6. 4. Override demand sensor during testing.
4. 6. 4. Turn on HVAC equipment and/or increase electric

load so the target demand will be exceeded.
4. 6. 4. Confirm equipment shut-down by observation of

equipment or EMCS report. Record the sequence of shut-down. The sequence
must agree with specified priority levels.
4. 6. 4. Selectively decrease equipment load so the target

demand will not be exceeded. Confirm the sequence of restoring loads in
accordance with priority level (reverse the sequence of shedding).
4. 6. 4. If rotation of shedding equipment in the same

priority level is required in the contract specifications, repeat steps in
4. 6. 4. 2 to 4. 6. 4. above to verify the rotation.
Page 186
Verify that the minimum off- time, minimum on-time,

4. 6. 4. 7
maximum off- time, and delay time are not violated for the HVAC equipment which
is given these limitations.
4.6.5 5.1
Day-night setback program. To reduce energy consumption

during unoccupied hours by lowering space temperature in the heating season
and raising space temperature in the cooling season.
4. 6. Verify the input parameters of the software. They

usually include time and day of the setbacks, and the space temperature during
the setbacks.
4. 6. 5. For heating setback test, change the setback time

from occupied to unoccupied (setback) time. The HVAC system should respond to
setback mode. If it is an air handling system, the outside air damper should
close5.4and the fan should cycle to maintain the setback temperature.
4. 6. 5. Change the setback temperature to slightly higher

than the current space temperature. The system should operate to reach and
maintain the setback temperature. During this period the outside air damper
should remain closed regardless of the fan operation.
4. 6. 5. After the system operation in 4. 6. 5. above is

confirmed, change the setback time to the correct occupied time. The system
should now be in the occupied mode and the fan and damper should operate
accordingly as specified.
4.6.6
4. 6. 5. For cooling setback test, repeat steps 4. 6. 5. 2 to
4. 6. above, except that in step 4. 6. 5. the setback temperature for
unoccupied period is set to slightly lower than the current space temperature
so the cooling system will be in operation during the test.
4. 6. 5. 6 See WS6B-9 for sample test work sheets.
Dry bulb economy cycle program. Dry-bulb air temperatures

are used as indices to utilize outdoor air for free cooling. There are
different versions of dry bulb economy cycles. However, they all compare
outside air temperature with a changeover temperature. The commissioning team
should review the contract specifications and be familiar with the scheme of
dry bulb economy cycle being used. Under EXHIBIT 5-B TEST PROCEDURES FOR AIR
HANDLING SYSTEMS a procedure is outlined for testing economy cycle controls by
using temperature simulators to simulate certain temperature sensors. That
procedure may also be used to test EMCS economy cycles. Since the changeover
temperature setting may easily be changed from the operator's console in an
EMCS, the following procedure is provided as an alternate for dry bulb economy
cycle test and is considered as more suitable for EMCS.
Page 187
4. 6. 6.1 Verify that the contract specification required

inputs are included in the EMCS input. They usually are the outdoor air, the
return air, the mixed air, and the change-over temperatures.
4. 6. 6. Request a report on current status of the air

handling unit and examine the outdoor temperature, the return air temperature,
the mixed air temperature, the change-over temperature, the outside air damper
position, and the return air damper position.
4. 6.6. If the outdoor temperature is higher than the

change-over temperature, the outside air damper should be at its minimum
position. If the outdoor temperature is lower than the change-over
temperature, the damper control should be under local control and the mixed
air temperature should be as required by the specifications. The return air
damper position should be confirmed to complement the outdoor air damper
position. In most projects the heating and the cooling coil controls also
depend upon the relationship of the outdoor and the change-over temperatures
so a maximum amount of mechanical cooling may be saved. Therefore, coil valve
positions should also be verified.
4. 6. 6. Change the change-over temperature setting from

that of condition in 4.6.6. to the other side (higher or lower) of the
outdoor temperature and confirm the positions of the outdoor air and the
return air dampers, and the positions of the coil valves.
4.6.7 Enthalpy economy cycle program. Air temperature and

humidity are used as indices to utilize outside air for free cooling. Since
enthalpy economy cycle senses actual temperature and humidity of both outdoor
air and return air to make control decisions, temperature and humidity
simulators or a portable temperature bath are needed to create the temperature
and/or humidity conditions desired. Test of this program should confirm the
outdoor air and return air damper actions and the correctness of the enthalpy
calculations
4. 6. 7.1 Confirm that the temperature and humidity of both

outdoor air and return air are included in the input of the program.
4. 6. 7. Request a report on current status of the air

handling unit and examine the outdoor temperature, outdoor humidity, outdoor
enthalpy, return air temperature, return air humidity, return air enthalpy,
and outside air and return air damper positions.
4. 6. 7. Compare the enthalpies of outdoor air and return

air from the report. Verify the correctness of damper positions.
4. 6. 7. Remove outdoor temperature and humidity sensors

from EMCS and substitute with temperature and humidity simulators to change
Page 188
the indicated outdoor enthalpy. An alternative-way is to immerse the outdoor

temperature sensor in a portable temperature bath. However, it is difficult
to accurately produce a desired outdoor humidity in the field. Therefore, if
the latter method is used to alter the outdoor enthalpy, the test may need to
be prolonged for weather change. To proceed with the test, set the outdoor
temperature (simulator or bath) and humidity (simulator) to different levels.
The enthalpy regions to be checked are detailed in TEST PROCEDURES FOR ECONOMY
CYCLE section of EXHIBIT 5-B TEST PROCEDURES FOR AIR HANDLING SYSTEMS. In
each of the enthalpy regions the enthalpy of the outside air and the return
air must be reported and compared to confirm the outdoor damper positions. A
psychrometric chart to visually locate the outside air and return air
conditions is helpful during this test.
4. 6. 7. After completing of test restore outdoor

temperature and humidity8.1 sensors to their original places.
4.6. 7.6 See WS6B-11 for sample test work sheets.
4.6.8 Ventilation air control program. To reduce energy

consumption during warm-up or cool-down periods by cutting off outdoor air.
However, some contract specifications (in some geographic areas of the
country) may require outdoor dampers be open during warm -up/cool- down periods
when the outdoor air is warmer/cooler than the space temperature. The
commissioning team should be familiar with the contract requirements.
4. 6. Verify that the program requires and includes input

of equipment start/stop time and day, occupied/unoccupied time schedule, and
space temperature.
4. 6. 8. It is assumed that this test is being conducted

during occupied period. Confirm that the outdoor damper is admitting outdoor
air
4. 6. 8. Change the occupied/unoccupied schedule to put the

system about 15 minutes before occupied period.
4. 6. 8. The outside air damper and the return damper

positions depend on relationship of the outdoor and the return air
temperatures and whether the system is in the heating or cooling mode at the
time of test.
4. 6. 8. If the system is in the heating mode and the

outdoor temperature is higher than the space temperature, the heat of the
outdoor air may be used to heat the space and the dampers should be under
,
local loop control. Otherwise, the outdoor damper should be closed so energy
is not wasted to heat the outdoor air. Therefore, the space temperature
setting should be altered during the test so it will be higher and lower than
the outdoor temperature during the course of the test. The damper positions
should be verified during the test to comply with the control logic of the
Page 189
software program.
4. 6. 8. Similar procedures should be used to test the

operation of the outdoor and the return air dampers for cooling mode.
4.6.9 Heating/cooling coil temperature reset program. To reset

heating coil discharge temperature (hot deck) lower or to set cooling coil
discharge temperature (cold deck) higher in accordance to certain indices to
save coil energy. Certain programs also sense air humidity to give upper
cooling coil reset temperature values. The heating/cooling coil temperature
reset program is especially important in multi-zone or dual-duct systems where
hot air and cold air are mixed to satisfy space loads.
4. 6. 9.1 Verify required input data. These data may include

upper and lower hot deck temperatures for heating, upper and lower cold deck
temperatures for cooling, index temperature to reset hot deck or cold deck
temperature, and maximum allowed space humidity. Outdoor air temperature or
space temperature is usually used as the index temperature.
4. 6. 9. Substitute the index temperature sensor with a

temperature simulator or place it in a portable temperature bath.
4. 6. 9. Vary the index temperature output by either

manipulate the simulator or by varying the bath temperature. Verify hot deck
or cold deck temperature change. The deck temperature should change in the
opposite direction as the index temperature changes. However, the deck
discharge temperature should not go beyond the specified upper and lower
temperature limits.
4. 6. 9. To test cold deck programs which limit the space

humidity level, set the space humidity limit slightly below the actual space
humidity (depending on system design it may be the return air humidity).
Repeat step 4. 6. 9. above and observe the cold deck temperature. The cold
deck temperature should decrease.
4.6.10 Reheat system reset program. To reset cooling coil

discharge air temperature of a reheat system in accordance with space load.
This program is very similar to the cold deck reset program described in (9)
above
4.6.10.1 Verify required input data. This may include

upper and lower cold deck temperatures, index temperature for resetting, and
maximum allowed space humidity. Outdoor air temperature or space temperature
is usually used as the index temperature.
Page 190
4.6.10.2 Substitute the index temperature sensor with a

temperature simulator or place it in a portable temperature bath.
4.6.10.3 Vary the index temperature output by either

manipulating the simulator or by varying the bath temperature. Verify coil
discharge temperature changes. The coil temperature should change in the
opposite direction as the index temperature changes.
4.6.10.4 Set the space humidity limit slightly below the

actual space humidity (depending on system design it may be the return air
humidity). Repeat step 4.6.10.3 above and observe the cooling coil discharge
temperature. This temperature should decrease.
4.6.10.5 See WS6B-13 for sample test work sheets.
4.6.11 Hot water temperature reset program. To reset hot water

temperature in accordance to heating load changes. In most cases the outdoor
air temperature is 4.6.11.1
used as the index to lower water temperature as the outdoor
air temperature increases.
Verify required input data. This may include

outdoor air temperature, the relationship of hot water temperature and outdoor
air temperature (reset schedule) and the maximum and minimum water
,
temperatures
4.6.11.2 Substitute the outside air temperature sensor with

a temperature simulator or place it in a portable temperature bath.
4.6.11.3 Vary the outdoor air temperature output by either

manipulating the simulator or by varying the bath temperature. Verify hot .
water supply temperature changes. The water temperature should change in

accordance with the reset schedule.
4.6.11.4 Change the outdoor air temperature simulator or

temperature bath to 2.8 °C (5 °F) higher than the high end of the reset
schedule. Verify that the hot water temperature is not lower than the minimum
water temperature in the reset schedule.
4.6.11.5 Change the outdoor air temperature simulator or

temperature bath to °C (5 °F) lower than the low end of the reset schedule.
Verify that the hot water temperature is not higher than the maximum water
temperature in the reset schedule.
4.6.12 Boiler sequencing program. To sequence boilers in a

multi-boiler plant under varying load conditions for achieving optimum plant
efficiency
Page 191

heating value of fuel, fuel consumption rate, energy output rate, and boiler
sequencing schedule. Steam pressure, temperature, and boiler feed water
temperature may also be required for steam boilers. Hot water supply and hot
water return temperatures are needed for water boilers. The output of the
program should show boiler efficiency data and boiler sequencing schedule
(on/off status of boilers).
4.6.12.2 In order to have the highest efficiencies at all

building load conditions, the boiler efficiency profile ( efficiency vs. load)
of each boiler must be known. Since this information may not be known to the
EMCS contractor at the time of commissioning, it may be difficult to perform a
true verification of this application software, i.e. to verify that the plant
is producing the highest efficiency at all load conditions. Therefore, the
test procedure described here is limited to verifying the indicated boiler
operation against the programmed boiler operation.
4.6.12.3 Manipulate the EMCS sensing parameter of the plant

output or building load, i.e. the flow rate of steam or hot water (depending
on system design, the inlet and outlet temperature of hot water system may be
appropriate). The plant output or building load is gradually increased from
minimum load to full load.
4.6.12.4 While changing the load as described in 4.6.12.3

above, verify boiler sequencing. The boiler on-off status and alarm
conditions as indicated by EMCS must agree with that programmed in the
software
4.6.13 Chilled water temperature reset program. To reset chilled

water temperature during low load or less critical cooling periods. This
program is usually done by sensing space temperature or sensing chilled water
coil valve position to reset chilled water temperature while monitoring indoor
humidity levels.

chilled water valve position (or control signal to valve) chilled water
temperature low limit, chilled water temperature, space temperature high
limit, space temperature and humidity, and space humidity high limit.
4.6.13.2 If space temperature is used to reset chilled

water temperature, substitute the temperature sensor with a temperature
simulator or place the sensor in a portable temperature bath. Manipulate the
temperature simulator or the temperature bath controls to raise temperature.
Verify that the chilled water temperature decreases or increases as required
by the specifications.
4.6.13.3 If chilled water valve position or control signal

to valve is used to reset chilled water temperature, manipulate the position
sensor to simulate opening of valve (increasing load). Verify that the
Page 192
chilled water temperature decreases.
4.6.13.3 4.6.13.4 Continue the action described in 4.6.13.2 or

above. Verify that the chilled water temperature does not decrease
below the low limit of the specified chilled water temperature.
4.6.13.3 4.6.13.5 Reverse the direction of space temperature or

valve position (or control signal to valve) as indicated in 4.6.13.2 or
and 4.6.13.4 above. Verify that the chilled water temperature
increases, yet it does not raise above the specified high limit specified for
the chilled water temperature.
4.6.13.6 Substitute the space humidity sensor with a

humidity simulator. Increase the simulated space humidity. Verify that when
the simulated humidity is higher than the specified high limit, as entered in
the program, the chilled water temperature decreases.
4.6.13.7 The design of the EMCS may sense air temperature

or valve positions (or control signal to valve) of more than one zone or HVAC
system and select the highest demand zone or system to reset the water
temperature. All zone or system sensors (temperature or position or control
signal) must be tested in sequence and verified as outlined above.
4.6.14 Condenser water temperature control program. To reset the

condenser water temperature from a fixed temperature downward, when the
outdoor wet bulb temperature is lower, to produce lower condenser water
temperature. This reduces the energy consumption of the chiller.
4.6.14.1 Verify required input data. The data may include

condenser water temperature, relationship of outdoor wet bulb temperature and
condenser water temperature, condenser water temperature low limit, outdoor
temperature and outdoor humidity.
4.6.14.2 Substitute outdoor temperature and outdoor

humidity sensors with temperature and humidity simulators. Manipulate
simulators to produce successively lower wet bulb temperatures. Verify that
the condenser water temperature decreases
4.6.14.4
4.6.14.3 When the simulated outdoor wet bulb temperature is
lower than the low limit of condenser water temperature/wet bulb relationship,
the condenser water temperature should not go below the low limit. Verify
this requirement.
Verify the relationship between the outdoor wet

bulb temperature and the condenser water temperature by referring to the
cooling tower data or contacting the cooling tower manufacturer. This
relationship is normally referred to as "the approach temperature". A 3.9 °C
Page 193
(7 °F) temperature differential, or approach temperature, is usually

specified.
Page 194
CHAPTER 7 FIRE SAFETY AIR MOVING SYSTEMS
1. Scope. This chapter provides inspection and testing procedures for fire
safety functions associated with air moving systems including heating,
ventilating, and air conditioning (HVAC) systems. These systems may be with
or without smoke control capabilities, systems specifically dedicated to zone
smoke control, or systems for stairtower pressurization.
2. Reference Documents.
b. ASHRAE Manual - Design of Smoke Control Systems for Buildings.
c. ASTM Standard E136 - Standard Method of Test for Noncombustibility of

Elementary Materials - 1973 (note: the standard has been changed but version
referenced here is that referenced by NFPA 90A)
d. NBSIR 75-673 - Development of a Fire Test Method for Flexible

Connectors in Air Distribution Systems.
e. NFPA Standard 31 - Standard for the Installation of Oil Burning

Equipment
f. NFPA Standard 54 (ANSI Z223) - National Fuel Gas Code.
g. NFPA Standard 70 - National Electrical Code.
h. NFPA Standard 72E - Standard on Automatic Fire Detectors.
i. NFPA Standard 90A - Standard for Installation of Air Conditioning and

Ventilating Systems.
j. NFPA Standard 92A - Recommended Practice for Smoke Control Systems

(draft document)
k. NFPA Standard 255 - Standard Method of Test of Surface

Characteristics of Building Materials.
l. NFPA Standard 259 - Standard Test Method for Potential Heat of

Building Materials.
m. GSA ORDER PBS P 5900. 2B - Accident and Fire Protection-General.
Page 195
n. UL Standard 181 - Standard for Factory -Made Air Ducts and Connectors.
o.
q. UL Standard 555 - Standard for Fire Dampers and Ceiling Dampers.
UL Standard 555S
p. - Standard for Leakage Rated Dampers for Use in
Smoke Control Systems.
UL Standard 900 - Standard for Test Performance of Fan Filter Units.
3. Inspection of Fire Safety Aspects of Air Moving Systems.
3.1 Air Moving systems shall be inspected to verify that the fire
safety requirements of the contract documents pertaining to materials and
installation have been fulfilled. The fire safety features of air moving
systems must be designed and specified in accordance with GSA Order PBS
P5900.2B, Accident and Fire Protection-General. This order requires that air
conditioning systems be in accordance with NFPA 90A with some specific
exceptions
3.2 See EXHIBIT 7 -A for inspection procedures and Appendix for check
lists for HVAC systems with and without zoned smoke control and for stairtower
pressurization systems.
4. Testing of Fire Safety Aspects of Air Moving Systems.

4.1 Systems for zoned smoke control and systems for stairtower
pressurization shall be tested in the field to verify that they meet the
requirements of the contract documents. HVAC systems do not require testing.
4.2 See EXHIBIT 7-B for testing requirements for zoned smoke control
systems that are either part of an HVAC system or are dedicated for smoke
control only.
4.3 See EXHIBIT 7-C for treating requirements for stairtower

pressurization systems.
Page 196
EXHIBIT A FIRE SAFETY INSPECTION PROCEDURES FOR AIR MOVING

SYSTEMS
1. Scope.The inspection procedures described in this EXHIBIT apply to the

fire safety of systems for heating, ventilating, and air conditioning (HVAC)
with or without smoke control capabilities or to systems only dedicated to
controlling smoke in building fires. This procedure is intended for HVAC
systems that are in accordance with the 1985 version of NFPA 90A. The levels
of performance, standards, test methods and other requirements listed in this
procedure are consequences based upon its foundation in the 1985 version of
NFPA 90A. This procedure is intended as an example inspection procedure, and
it is anticipated that users will modify the procedure to suit their needs.
2 . Reference standards
a. ASHRAE 15 (Safety Code for Mechanical Refrigeration) is intended to
assure the safe design, construction, installation, operation, and inspection
of refrigeration systems. Among other safety features and precautions, this
standard describes requirements of pressure-limiting devices and pressure-
relief protection, including installation requirements of refrigeration piping
and machinery room housing refrigerating equipment.
b. ASTM E136 (Standard Method of Test for Noncombustibility of

Elementary Materials - 1973) is a test method for determination of
noncombustibility of elementary materials, to indicate those materials which
do not act to aid combustion or add appreciable heat to an ambient fire. It
is not intended to apply to laminated or coated materials, (note: the standard
has been changed but version referenced here is that referenced by NFPA 90A)
c. NBSIR 75-673 (Development of a Fire Test Method for Flexible

Connectors in Air Distribution Systems) is a test method which evaluates the
fire performance of a flexible duct connector in terms of: (a) resistance of
the flexible connectors to failure by direct fire penetration, (b) adequacy of
attachment method of the flexible connector to the duct, and (c) effectiveness
of the blocking (firestopping) of the penetration through a fire-rated floor
and ceiling.
d. NFPA 31 (Standard for the Installation of Oil Burning Equipment)

applies to oil-fired stationary equipment including residential, commercial
and industrial steam, hot water plants, and warm air heating plants.
e. NFPA 54 (ANSI Z223, National Fuel Gas Code) is a safety code which
applies to the installation of fuel gas piping systems, fuel gas utilization
equipment and related accessories. Among the areas this code addresses are
piping design, piping materials, piping components, piping installation,
Page 197
piping testing, equipment installation, and equipment venting.
f. NFPA 70 (National Electrical Code) applies to the installation of

electric conductors and equipment within public and private buildings, and the
code contains provisions considered necessary for safety to life and property.
This code addresses wiring design, protection, methods, and materials. Also
addressed are electrical equipment, special occupancies, and communication
systems
g. NFPA 72E (Standard on Automatic Fire Detectors) provides basic

minimum requirements for the performance of automatic fire detectors with the
intent of ensuring timely warning for the purposes of life safety and property
protection. The kinds of fire detectors addressed include heat sensing, smoke
sensing, flame sensing, and gas sensing. The standard addresses installation,
maintenance and testing of detectors.
h. NFPA 90A (Standard for the Installation of Air Conditioning and

Ventilating Systems) prescribes minimum fire safety requirements for systems
for the movement of environmental air within structures. This standard
addresses aspects of fire safety for these systems in detail including
definitions, system components, impact on fire integrity of building
construction, and controls.
i. NFPA 255 (Standard Method of Test of Surface Characteristics of

Building Materials) is a method of testing the surface burning characteristics
of building materials to determine comparative characteristics by evaluating
the flame spread over the surface and the density of smoke produced.
j NFPA 259 (Standard Test Method for Potential Heat of Building

.
Materials) is a test to determine, under controlled laboratory conditions, the

heat released from a material under fire conditions.
k. UL 181 (Standard for Factory-Made Air Ducts and Connectors) is a

standard test method for air ducts and connector systems. The air ducts and
connectors covered by this standard include preformed lengths of flexible or
rigid ducts, materials in the form of boards for field fabrication of lengths
of rigid ducts, and preformed flexible connectors. The method includes tests
for surface burning characteristics, flame resistance, flame penetration,
burning, corrosion resistance, mold resistance, temperature resistance,
puncture resistance, static load resistance, impact resistance, erosion
resistance, pressure resistance, collapse resistance, tension resistance,
bending resistance, leakage resistance. Air ducts are classified as Class 0,
Class 1 or Class 2. This standard requires that installation instructions be
supplied by manufacturers.
l. UL 555 (Standard for Fire Dampers and Ceiling Dampers) is a test

method applicable to fire dampers and ceiling dampers intended for
installation in floor-ceiling and roof -ceiling assemblies. The test method
includes construction requirements and tests for fire endurance, hose-stream
Page 198
exposure, closing reliability, duct loading exposure salt-spray exposure, and

,
spring closing force. Fire dampers are rated at 3/4 hr, 1 hr, 1-1/2 hr, and 3
hr. Ceiling dampers are not assigned hourly ratings, but rather are assembly
components designed for use in specific hourly rated resistive assembles. The
standard requires that manufacturers supply installation instructions for
these dampers.
m. UL 555S (Standard for Leakage Rated Dampers for Use in Smoke Control
Systems) is a test method for leakage rated dampers intended for use in
heating, ventilating, and air conditioning systems. The test method includes
construction requirements and tests for cycling, temperature degradation, duct
loading exposure, salt- spray exposure, and air leakage. These smoke dampers
are classified as 0, I, II, III, or IV leakage rated dampers, and they are
tested at 250 'F or at an elevated temperature selected in increments of 100
'F above 250 'F.
n. UL 900 (Standard for Test Performance of Fan Filter Units) presents

test requirements of air filter units of both washable and throwaway types.
Filter units are subjected to a flame -exposure test and a spot-flame test.
Filter units are classified as either Class 1 or Class 2.
3. General inspection procedures.

3.1 Check ducts to verify that materials of duct construction are as
specified. Ducts may be constructed of iron, steel, concrete, masonry or clay
tile. For ducts constructed of other materials, check that they are Class 0
or Class 1 ducts as specified and that they are tested in accordance with UL
181, Standard for Factory-Made Air Ducts and Connectors. The duct class is
imprinted on it by the manufacturer.
3.2 Check duct installation. Duct installation including the hangers

must not reduce the fire resistance rating of structural members and of
assemblies. Frequently, structural members and assemblies have fire
protective coverings, such as drywall construction or a sprayed-on layer.
Check that ducts are installed in such a manner that these protective
coverings are not damaged. Check that clearance from ducts to combustible
construction is in accordance with NFPA 90A. In addition, check that where
ducts pass through walls, floors, or partitions the openings in construction
around the ducts are in accordance with NFPA 90A.
3.3 Check installation and materials of duct connectors and flexible

duct connectors. Class 1 or Class 2 duct connectors tested in accordance with
UL 181, Standard for Factory-Made Air Ducts and Connectors, may be used
subject to limitations of NFPA 90A. The class is imprinted on the duct
connector by the manufacturer. Duct connectors must not exceed 14 ft in
length, and they must not pass through floors of buildings. Flexible duct
connectors meeting a 1-hour fire exposure, as set forth in NBSIR 75-673,
Development of a Fire Test Method for Flexible Connectors in Air Distribution
Page 199
Systems, may pass through one floor to connect ducts with air terminal units
subject to the limitations of NFPA 90A including firestopping around openings.
Flexible duct connectors must not exceed 14 ft in length. CAUTION: Because
the characteristics of duct connectors and flexible duct connectors are
different, one should not be substituted for the other.
3.4 Check duct coverings and linings to verify that their fire safety
requirements are as specified. Coverings and linings must be in accordance
with the requirements of NFPA 90A. Check that duct coverings do not conceal
any service opening.
3.5 Check direct access and inspection provisions. A service opening

or a telescoping or removable duct section are used for direct access and
inspection. Check that a service opening or a telescoping or removable duct
section is provided in ducts adjacent to fire dampers, smoke dampers and smoke
detectors. Check that these access openings are identified with letters no
less that 0.0127 m (1/2 inch) in height which identify the fire protection
device within. Check that service openings are provided in horizontal ducts
and plenums where required by contract documents.
3.6 Check plenums between ceilings and floors. Check materials exposed
to air flow in these plenums to verify that these materials have smoke
developed ratings not greater than 50 and are non-combustible or limited
combustible except for electrical wiring, electrical equipment, optical fiber
cable and pneumatic tubing. Check that electrical wiring and equipment in
plenums is installed in accordance with NFPA 70, National Electrical Code.
Check that optical fiber cable in plenums conforms to provisions of NFPA 70,
National Electrical Code, or is listed as having adequate fire-resistant and
low smoke producing characteristics. Check that pneumatic tubing for control
systems is listed as having adequate fire-resistant and low smoke producing
characteristics
The following notes are provided for the convenience of the user of this
inspection method, however, in matters of contract compliance or code
requirements the definitions and wording of NFPA 90A apply:
3.6.1 A smoke developed rating of a material refers to a number

or classification of a material obtained according to NFPA 255, Standard
Method of Test of Surface Characteristics of Building Materials, which
measures visible smoke.
3.6.2 A non-combustible material is a one which, in the form in

which it is used and under the conditions anticipated, will not ignite,
support combustion, or release flammable vapors when subjected to fire or
heat. Many common materials such as iron, steel, aluminum, concrete, masonry
and clay tile are non- combustible Materials reported as non- combustible
.
when tested in accordance with ASTM E136, Standard Method of Test for
Noncombustibility of Elementary Materials, are considered non- combustible
materials
Page 200
3.6.3 A limited combustible material is one not complying with

the requirements of a non-combustible material, which, in the form in which
it is used, has a potential heat value not exceeding 8140 kJ/kg (3500 Btu/lb)
(see NFPA 259, Standard Test Method for Potential Heat of Building Materials)
and complies with one of the following paragraphs (a) or (b) Materials which
decrease in fire performance due to age or usage are considered combustible
materials
3. 6. 3.1 Materials having a structural base of non-

combustible material, with a surfacing not exceeding a thickness of 0.00318 m
(1/8 inch) which has a flame spread rating not greater than 50.
3. 6. 1.2 Materials other than described in 3. 6. 3.1, having

neither a flame spread rating greater than 25 nor evidence of continued
progressive combustion, and of such composition that surfaces that would be
exposed by cutting through the material on any plane would have neither a
flame spread rating greater than 25 nor evidence of continued progressive
combustion.
3.6.4 The flame spread rating of a material refers to a number or

classification of a material obtained in accordance with NFPA 255, Standard
Method of Test of Surface Characteristics of Building Materials.
3.7 Check air filters. Check air filters to verify that they have the
classification required by the contract documents and that they have been
rated in accordance with UL 900, Standard for Test Performance of Fan Filter
Units
3.8 Check that exposed fan inlets are protected with metal screens in
accordance with contract documents to prevent the entry of paper, trash, and
similar foreign material.
3.9 Check that heating and cooling equipment is installed in accordance

with manufacturers' instructions and the following applicable standards:
Description Standard
Mechanical refrigeration used ASHRAE 15, Safety Code for

with air duct systems Mechanical Refrigeration
Gas fired heating furnaces combined NFPA 54 (ANSI Z223) National Fuel
with cooling units in the same duct Gas Code
Oil fired heating furnaces combined NFPA 31, Standard for the
with cooling units in the same duct Installation of Oil Burning
Equipment
Electrical duct heaters Part F, Duct Heaters, of Article 424

of NFPA 70, National Electric Code
Page 201
3.10 Check the location, fire protection rating and installation of

fire dampers. Check that fire dampers are located at all places where they
are required by the contract documents Check the label attached to the fire
.
dampers to verify that they meet the fire protection rating specified by the
contract documents and that the damper has been tested in accordance with UL
555, Standard for Fire Dampers and Ceiling Dampers. Check that fire dampers
have been installed in accordance with the conditions of their listing and the
manufacturer's installation instructions which are supplied with the damper.
Further check installation by removing fusible link (where applicable) and
operating damper to verify that it closes fully. It is desirable to operate
dampers with normal air flow to assure that they are not held open by the air
stream. Remember to reinstall all fusible links that have been removed during
inspection.

ceiling dampers. Check that ceiling dampers are located at all places where
they are required by the contract documents. Check the label attached to the
ceiling dampers to verify that they are appropriate for the floor-ceiling or
roof-ceiling assembly in which they are used and that the damper has been
tested in accordance with UL 555, Standard for Fire Dampers and Ceiling
Dampers. Check that ceiling dampers have been installed in accordance with
the conditions of their listing and the manufacturer's installation
instructions which are supplied with the damper. Further check installation
by removing fusible link (where applicable) and operating damper to verify
that it closes fully. It is desirable to operate dampers with normal air flow
to assure that they are not held open by the air stream. Remember to
reinstall all fusible links that have been removed during inspection.
3.12 Check the location, fire protection classification and

installation of smoke dampers. Check that smoke dampers are located at all
places where they are required by the contract documents. Check the label
attached to the smoke dampers to verify that they meet the leakage and
temperature class specified by the contract documents and that the damper has
been tested in accordance with UL 555S, Standard for Leakage Rated Dampers for
Use in Smoke Control Systems. Check that smoke dampers have been installed in
accordance with the conditions of their listing and the manufacturer's
installation instructions. During normal system operation, check that each
smoke damper required by the contract documents to be closed is fully and
tightly closed, and that each smoke damper required to be opened is fully
opened.

combination fire and smoke dampers. Check that combination fire and smoke
dampers are located at all places where they are required by the contract
documents. Check the label(s) attached to the combination fire and smoke
dampers to verify that they meet the fire protection rating specified b> the
contract documents and that the damper has been tested in accordance with UL
555, Standard for Fire Dampers and Ceiling Dampers. Also, check the label to
verify that they meet the leakage and temperature class specified by the
Page 202
. .
contract documents and that the damper has been-^tested in accordance with UL
555S, Standard for Leakage Rated Dampers for Use in Smoke Control Systems.
Check that combination fire and smoke dampers have been installed in
accordance with the conditions of their listing and the manufacturer's
installation instructions. Further check installation by removing fusible
link (where applicable) and operating damper to verify that it fully closes.
It is desirable to operate dampers with normal air flow to assure that they
are not held open by the air stream. Remember to reinstall all fusible links
that have been removed during inspection.
4. Controls for systems without smoke control capability.

4.1 Check manual controls. Check that each air distribution system has
manually operated device(s) that will stop the operation of supply, return,
and/or exhaust fan(s) in an emergency, and that this device is located as
specified. With the system in normal operating mode, operate each manual
shutdown device, and check that all fans required by the contract documents to
be stopped have actually stopped. Also, check that any smoke dampers required
by the contract documents to be closed are fully and tightly closed.
4.2 Check automatic controls. If automatic shutdown capability is

required, check that the air system has automatic shutdown capability. Check
that detectors used to activate any automatic shutdown are located as
specified, are of the type as specified, and are installed in accordance with
NFPA 72E, Standard on Automatic Fire Detectors. Where applicable, check
system shutdown by detectors located in supply duct, return duct, and by
detector system installed in the building. With the system in normal
operating mode, activate the detector (where applicable) in the return air
stream. Check that all fans required by the contract documents to be stopped
have actually stopped. Also, check that any smoke dampers required by the
contract documents to be closed are fully and tightly closed.
5. Controls for systems with zoned smoke control capability.

5.1 Check manual controls. Check that devices required by the contract
documents for manual activation and deactivation of the zoned smoke control
system have been installed (a detailed check of the functioning of manual
control is included in EXHIBIT B)
5.2 Check automatic controls. Check that devices required by the

contract documents for automatic activation and deactivation of the zoned
smoke control system have been installed (a detailed check of the functioning
of automatic control is included in EXHIBIT B)
Page 203
EXHIBIT B TEST PROCEDURES FOR ZONED SMOKE CONTROL SYSTEMS
1. Scope. The test procedures described in this EXHIBIT apply to zoned

smoke control systems that are either dedicated systems or part of systems for
heating, ventilating, and air conditioning (HVAC). These procedures should be
thought of as an initial effort to develop information which could be of use
to engineers and code officials tasked with determining the acceptability of a
zoned smoke control system. It is anticipated that users will want to modify
the methods to suit their specific needs.
2. General references.
a. ASHRAE manual "Design of Smoke Control Systems for Buildings" by
Klote and Fothergill consolidates and systematically presents data and
calculation procedures necessary to smoke control systems designers and
discusses design criteria. Included are discussions of the driving forces of
smoke movement, the principles of smoke control, calculation of effective flow
areas, concept of symmetry, and design parameters. A computer program for
analysis of smoke control systems is presented. Concepts of stairwell
pressurization and zoned smoke control are presented.
b. NFPA 92A, Recommended Practice for Smoke Control Systems. This

document provides recommendations about design, installation, testing,
operation, and maintenance of new and retrofitted mechanical air conditioning
and ventilation systems for the control of smoke.
3. Emergency power. If standby power or other emergency power has been

provided for the operation of the zoned smoke control system, acceptance
testing shall be conducted with emergency power and normal power.
4. Smoke control diagram. Identify the exact location of each smoke

control zone. If it is not part of the building plans, make a smoke control
zone diagram of the building. This diagram should include the locations of
all zone boundaries and of all doors in those boundaries.
5. Normal operation test. With all building HVAC systems in normal

operation, the zoned smoke control system shut off, and the smoke barrier
doors closed; measure and record the pressure differences across each smoke
barrier door. Evaluate these pressure differences to determine that they are
appropriate for the balanced HVAC system.
Page 204
.
6. Smoke mode test. Each smoke zone is to-be individually tested by

performing the following sequence.
6.1 Activate smoke control system operation in the zone. This should
be accomplished by putting one of the detectors into alarm that are intended
to activate the smoke control system in that zone.
6.2 Check that the operation of fans is as required by the contract

documents
6.3 Check that the position of smoke dampers is as required by the

contract documents. Also, check that any smoke dampers required to be closed
are fully and tightly closed.
6.4 Check to verify that all doors required by the contract documents
to be closed during smoke control system operation are fully closed and that
they operate freely allowing use during evacuation without becoming jammed in
their door frames. This should include doors in the boundary of the smoke
zone being tested.
6.5 Measure and record pressure differences across all closed doors in
the boundary of the smoke zone being tested. Pressure differences resulting
from air flowing to the smoke zone being tested are to be recorded as positive
values, and pressure differences resulting from air flowing from the smoke
zone being tested are to be recorded as negative values.
6.6 Check that the measured pressure difference is within the

acceptable range as defined in the contract documents. If the pressure
difference is not in the acceptable range, double check that the state of
fans, dampers and doors is as required. If any of these is not as required,
they should be fixed and the zone retested. After this, if the pressure
difference is not acceptable, the flow rates of air to and from the smoke
zones in question should be measured and adjusted as appropriate. If the
pressure differences are too low after these actions, excessive air leakage
paths in the construction should be filled, caulked or sealed as appropriate.
(Often it is very difficult to locate leakage paths in buildings. Chemical
smoke from smoke bombs can be used to find these leakage paths. The high
pressure sides of smoke barriers are exposed to heavy concentrations of
chemical smoke, while the low pressure side of the barrier is examined for
smoke leakage that indicates the location of a leakage path. Exterior walls,
interior partitions, floors and ceilings including areas above suspended
ceilings must not be overlooked when hunting for excessive leakage areas.)
Then the zone should be retested.
6.7 Test for smoke feedback into supply air. Place six smoke bombs (3
minute duration size) in a metal container, simultaneously ignite all bombs,
and locate container near exhaust inlet in smoke zone being tested so that all
of the chemical smoke produced by the bombs is drawn directly into the exhaust
Page 205
air stream. Check that air supplied to other zones of the building has no
trace of chemical smoke. If chemical smoke is detected in this supply air,
its path should be determined, the path should be blocked, and then the smoke
feedback test should be conducted again. (The two most likely causes of smoke
feedback are a leaky or partly opened return air damper and an outside air
inlet located in the vicinity of the exhaust air outlet.)
6.8 Make sure that this zone has been returned to its normal setting
before continuing to test other zones.
7. Duct mounted smoke detector test. Verify that the smoke detector
is properly selected and properly installed to satisfactorily measure any
products of combustion located in the duct. Smoke is drawn through the
detector sampling chamber by the air flow velocity pressure. Since velocity
pressure is a function of the volume of air flowing (cfm) and the area of the
duct, the test team shall confirm that the velocity pressure is within the
range specified by the equipment manufacturer and the contract specifications.
Test the duct mounted smoke detector operation by setting off a smoke bomb in
the air stream ahead of the detector. Confirm that the detector signals the
alarm properly and that the total post-alarm sequence is proper.
Page 206
EXHIBIT C TEST PROCEDURES FOR STAIRWELL PRESSURIZATION SYSTEMS
1. Scope. The test procedures described in this EXHIBIT apply to systems

for stairwell pressurization. These procedures should be thought of as an
initial effort to develop information which could be of use to engineers and
code officials tasked with determining the acceptability of a pressurized
stairwell system. It is anticipated that users will want to modify the
methods to suit their specific needs.
2. General references.
a. ASHRAE manual "Design of Smoke Control Systems for Buildings" by
Klote and Fothergill consolidates and systematically presents data and
calculational procedures necessary to smoke control systems designers and
discusses design criteria. Included are discussions of the driving forces of
smoke movement, the principles of smoke control, calculation of effective flow
areas, concept of symmetry, and design parameters. A computer program for
analysis of smoke control systems is presented. Concepts of stairwell
pressurization and zoned smoke control are presented.
b. NFPA 92A, Recommended Practice for Smoke Control Systems, is a draft

document to be voted on by NFPA in November 1987. This document provides
recommendations about design, installation, testing, operation, and
maintenance of new and retrofitted mechanical air conditioning and ventilation
systems for the control of smoke.
3. Emergency power. If standby power or other emergency power has been

provided for the operation of the stairwell pressurization control system,
acceptance testing shall be conducted with emergency power and normal power.
4. Normal operation test. With all building HVAC systems in normal

operation, any zoned smoke control systems shut off, and the stairwell doors
closed, measure and record the pressure differences across each stairwell
door. The sign convention for all pressure difference readings in the
stairwell tests is: a pressure difference resulting from a flow from the
stairwell is positive, and a pressure difference resulting from a flow to the
stairwell is negative. Evaluate these pressure differences to determine that
they are appropriate for the balanced HVAC system.
5. Stairwell pressurization test. Activate the stairwell

pressurization systems by putting a detector in alarm as required by the
contract documents. Test each pressurized stairwell by conducting the
Page 207
"
following steps.
5.1 With all stairwell doors closed (except for the exterior ground
floor door if it is required to be opened upon system activation) measure and
,
record pressure differences across each closed stairwell door.
5.2 Open the exterior ground floor stairwell door (except if the
exterior ground floor door is required to be opened upon system activation)
and measure and record pressure differences across each closed stairwell door.
For stairwells without a ground floor exterior door, another highly severe
open door condition must be tested. This can be an exterior door not at the
ground floor or a large flow path to the outside created by opening the
stairwell door and other doors including an exterior building door.
5.3Open an additional stairwell door, and measure and record pressure

differences across each closed stairwell door. Repeat this step opening
another door each time until the required number of doors is opened. The
required number of doors is that number that must be opened during testing as
stipulated in the applicable codes or contract documents.
5.4 With the required number of doors opened, check flow direction
through open doorways using a 1.83 m (6 ft) strip of tissue paper secured at
the top of the door frame
5.5 Check that the measured pressure difference is within the

acceptable range as defined in the contract documents. If the pressure
difference is not in the acceptable range, double check that the states of
fans, dampers and doors is as required. If any of these is not as required,
they should be fixed and the zone retested. After this, if the pressure
difference is not acceptable, the flow rate of air to the stairwell in
question should be measured and adjusted as appropriate. If the pressure
differences are too low after these actions, excessive air leakage paths in
the construction should be filled, caulked or sealed as appropriate. (Often
it is very difficult to locate leakage paths in buildings. Chemical smoke
from smoke bombs can be used to find these leakage paths. The stairwell is
filled with chemical smoke and pressurized, while the low pressure side of the
stairwell barriers are examined for smoke leakage that indicates the location
of a leakage path.) Then the zone should be retested.
Page 208
. . .
CHAPTER 8 UNITARY AIR CONDITIONING EQUIPMENT
1. Scope. This part provides inspection and testing procedures for unitary
air conditioning equipment. A unitary air conditioning unit consists of one
or more factory-made assemblies designed to be used as a matched assembly. It
normally has an evaporator, a compressor, a condenser, and may include a
heating section. Included equipment are packaged rooftop units, computer room
air conditioning units, and packaged terminal air conditioners (PTAC) which
are also known as through- the -wall units. Heat pumps are not included in this
chapter
2. Reference standards.
b. ASHRAE Standard 37 - Method of Testing for Rating Unitary Air

Conditioning and Heat Pump Equipment.
c. ASHRAE Standard 41.6 - Standard Method for Measurement of Moist Air

Properties
d. ASHRAE Standard 58 - Method of Testing Room Air Conditioner Heating

Capacity
e. ASHRAE Standard 62 - Ventilation for Acceptable Indoor Air Quality.
f. ASHRAE Standard 111-1988 - Practices for Measurement, Testing,

Adjusting and Balancing of Building Heating, Ventilation, Air Conditioning and
Refrigeration Systems.
g. ARI Standard 110 - Standard for Air-Conditioning and Refrigerating

Equipment Nameplate Voltages.
h. ARI Standard 210 - Standard for Unitary Air-Conditioning Equipment.
i. SRI Standard 310 - Standard for Packaged Terminal Air- Conditioners.
j. ARI Standard 360 - Standard for Commercial and Industrial Unitary

Air-Conditioning Equipment.
k. ARI Standard 630 - Standard for Selection, Installation, and Servicing

of Humidifiers.
l. Associated Air Balance Council - National Standards for Total System
Page 209
Balance
m.National Environmental Balancing Bureau - Procedural Standards for

Testing-balancing-adjusting of Environmental Systems.
n. Applicable codes of the National Fire Protection Association.
o. Applicable codes of Underwriters Laboratories, Inc.
3. Unitary air conditioning equipment inspection.

a. Unitary air conditioning equipment shall be inspected for
construction and installation to meet safety and functional requirements.
b. See EXHIBIT 8 -A for inspection procedures and Appendix for inspection

check lists.
4. Unitary air conditioning equipment testing.

4.1 Unitary air conditioning equipment shall be tested in the field to
meet the capacity requirements of the contract specifications. Two basic type
of tests shall be included:
4.1.1 Capacity and other performance compliance of the air

conditioning unit.
4.1.2 Functional performance compliance of the automatic control

of the unit.
4.2 If the building load at the time of testing does not meet the
system capacity, introduction of false load may be necessary. Tests shall not
cause excessively uncomfortable conditions in the building.
4.3 See EXHIBIT 8-B for test procedures and Appendix for test work
sheets
Page 210
.
EXHIBIT 8-A INSPECTION PROCEDURES FOR UNITARY AIR CONDITIONING

UNITS

unitary air conditioning units. Included equipment are packaged rooftop
units, computer room air conditioning units, and packaged terminal air
conditioners (PTAC)
a. ASHRAE Standard 15 (Safety Code for Mechanical Refrigeration) is
intended to assure the safe design, construction, installation, operation, and
inspection of refrigeration systems. Among other safety features and
precautions, this Standard describes requirements of pressure - limiting devices
and pressure - relief protection, including installation requirements of
refrigerant piping and machinery room housing refrigerating machine.
b. ASHRAE Standard 37 (Method of Testing for Rating Unitary Air

Conditioning and Heat Pump Equipment) provides standard test methods for
determining the cooling capacity of unitary air-conditioning equipment and the
cooling and/or heating capacities of unitary heat pump equipment. Unitary
equipment is limited to electrically driven mechanical compression types. It
does not include testing method for room air-conditioners.
c. ASHRAE Standard 62 (Ventilation for Acceptable Indoor Air Quality)

gives ambient air quality guidelines and outdoor air requirements for most
space ventilation applications. It also gives general requirements for
ventilation systems and equipment.
d. ARI Standard 110 (Air-Conditioning and Refrigeration equipment

Nameplate Voltages) provides definitions, classifications, recommended
standard nameplate voltages, recommended maximum and minimum utilization
voltages for air-conditioning and refrigerating equipment, heat pumps, and
electric furnaces.
e. ARI Standard 210 (Unitary Air-Conditioning Equipment) provides

definitions, classifications, requirements for testing and rating, performance
requirements, safety requirements, and conformation conditions for
factory-made residential, commercial, and industrial air-conditioners or
matched assemblies with electrically-driven mechanical compressors. This
standard apply to units with cooling capacities less than 135,000 Btuh.
f. ARI Standard 310 (Packaged Terminal Air- Conditioners ) applies to

factory-made residential, commercial, and industrial packaged terminal
air-conditioners. It provides definitions, classifications, standard
Page 211
equipment, requirements for testing and rating, specifications, literature and

advertising requirements, performance requirements, design, construction and
assembly requirements for safety, and conformance conditions. This standard
does not applies to rating and testing of individual assemblies, such as a
cooling or heating section, for separate use and may be used for systems with
a total external duct static resistance up to 0.1 inch of water.
g. ARI Standard 360 (Commercial and Industrial Unitary Air-Conditioning

Equipment) provides, for commercial and industrial unitary air-conditioning
equipment: definitions and classification; requirements for testing and
rating; specifications, literature and advertising requirements; performance
requirements; safety requirements; and conformance conditions. This standard
does not apply to unitary air-conditioners with capacities less than 135,000
Btuh.
h. ARI Standard 630 (Standard for Selection, Installation, and Servicing

of Humidifiers) describes humidifier selection procedure, installation
practices, and service practices of humidifiers used in central stations and
self-contained applications.
3. Unitary air conditioning unit general inspection.

3.1 Review equipment manufacturer's instructions on start-up and
operation procedures.
3.2 Give general inspection of compressor, refrigerant system, fan,

motor, air filters, cooling coils, heating coils, dampers, fan and coil bases,
vibration isolation units, outdoor heat exchanger, and their associated
equipment, including associated electrical equipment, piping, ductwork, etc.
Be sure that no apparent damage or rusting occurred.
3.3 Check equipment name plates to verify equipment model and serial
number. They must have the same model numbers as approved submittals.
Check for service access spaces around unit for operation and
3.4
maintenance. Manufacturer's recommended spaces must be provided. Pay special
attention to coil and filter replacement and cleaning spaces and access
spaces
3.5 Inspect equipment space for possible fire hazards. The space
should be kept free of combustible material and construction debris.
3.6 Verify service piping (steam, gas, condenser water, condensate,

etc.), pipe fittings and accessary equipment for the unit against project
drawings and equipment manufacturer's recommendations for completeness and
proper installation. Fittings and accessories include but not limited to
valves, strainers, thermometer wells, piping supports, steam traps, etc.
Page 212
3.7 Check water flow direction marks of -check valves and flow switches.
3.8 Check piping at equipment connections. Pipes should be supported

from building structure without undue stress on coils.
3.9 All moving parts (motors, belts, etc.) should have protective
shields for personnel safety.
3.10 Check alignment of motor driven equipment. Using some simple

tools such as straight edges, square edges, plumb lines, and strings yield
good results. Also observe shaft and coupling for misalignment while
equipment is running.
3.11 Observe belt tightness of fans. Use belt tension gage if needed.
Belt tension should be as recommended by belt manufacturer.
3.12 Make sure required lubrication is complete (fan, motor, etc.)
3.13 Be sure the system is charged with the right kind of refrigerant.
Check sight glass for proper level.
3.15 Be sure crankcase heater is installed snugly in position.

Crankcase heater should be on during compressor off time.
3.16 Check oil level of compressor before and during compressor

operation. Oil should not be foaming excessively.

thermometers, gages, temperature and flow measuring and control devices.
Required straight pipe runs and arrangements for temperature and flow
measuring devices must be met.
3.18 Verify installed wiring against project drawings and

3.20 Check safety control wiring connections. All safety control

switches (switches respond to temperature, pressure, smoke, etc. to break the
safety control circuit) should be connected in the ungrounded conductor.
Page 213
3.23 Test-run motors (fan, pump, etc.) to^check correct direction of

rotation.
3.24 Check surface paint for damages and omissions. Equipment

nameplates must not be painted over. Required equipment labels must be
present and legible.
3.26 No leakage should be noted for water, oil, and steam.
3.27 Inspect duct connections at air conditioning unit for excessive

air leakage.
3.28 Be sure that temperature and pressure indicators for oil system
are functioning properly to indicate the oil system operation. Oil pressure
must be as recommended by the manufacturer.
3.29 Check compressor interlocking function with oil pressure to insure

the operation of paragraph 3.28 above.
compressor if so specified.
3.32 Check oil heating system for proper operation. Electric wiring
should be verified as per manufacturer's submittals or checked to be sure that
crankcase heater power is on even when the main power is off. The crankcase
heater should be installed snugly in its position. It should be on during
compressor off time.
3.33 Check oil level before and during operation. Oil should not be
foaming excessively.
3.34 For units with remote condensers, check refrigerant pipe pitch and
oil traps for proper oil return.
3.35 For air cooled and evaporatively cooled units, spaces for air
circulation is important. Be sure that manufacturer's recommendations are
followed and air is not short circulated from discharge to intake.
3.36 Check direction of fan rotation for air cooled condenser.
3.27 For air cooled condensers equipped with damper controls for low
ambient operation, check damper mechanism for proper adjustment and operation.
3.38 Check direction of fan rotation for evaporative condenser.
Page 214
.
3.39 Check water level of evaporative condenser. Water float valve

shall not "chatter". Spray nozzles should have correct pattern without
blockage. There shall be no excessive water carry- through
3.40 If evaporative condenser is specified and equipped with bleed-off

arrangement, visually check valve adjustment for flow.
3.41 Additional inspection procedures specifically pertaining to

rooftop, computer room, and packaged terminal air-conditioners are listed in
paragraphs 4, 5, and 6 below.
4. Inspection items specific to rooftop units.

4.1 Check unit location in relationship to roof supporting structure.
Unit manufacturer's instruction must be followed.
4.2 Check roof curb and unit installation for correct leveling.
4.3 Noise is often a problem for rooftop units. Inspect to make sure
that the unit and ducts are properly installed. Ducts should have flexible
connections and they should not be in contact with roofing structure above
flexible connections. Spaces between ducts or pipes and roofing structure in
duct/pipe sleeves should be sealed.
4.4 Inspection check list CL 8A-1 for rooftop air conditioning units is
included in the Appendix.
5. Inspection items specific to computer room units.

5.1 For units equipped with indicating lights and test switches, press
switches to verify indicating light status with unit operation. Indicating
lights usually include power on/off, system on/off, humidifier on/off,
free-cooling status, hot gas status, room or return air humidity range,
cooling and heating status. Note that indicating lights usually read room
conditions independent of system controls.
5.2 For units equipped with audible alarms, create unfavorable

conditions to confirm alarm functions. Some units may have alarms in
conjunction with indicating lights. Check that audible alarms can be manually
silenced, if so specified or included in product data.
5.3 If unit is specified to dehumidify only when air flow is reduced,

check fan speed control or damper control against compressor operation to
verify control.
5.4 For units equipped with underfloor water detector, fire detector,
and smoke detector, create conditions (presence of water, high temperature,
Page 215
and smoke) at the respective sensors to verify alarm actions.
5.5 Verify sensor calibrations and readouts.
5.6 Check that control deadbands and alarm set points can be easily
changed if so specified.
5.7 Inspection check list CL 8A-2 for computer room air conditioning
units is included in the Appendix.
6. Inspection items specific to packaged terminal

air-conditioners
6.1 Packaged terminal air-conditioners are installed in wall sleeves.
Inspect installation to make sure that units may be removed easily for
servicing and replacement.
6.2 Inspect around units to be sure that wall sleeves, unit cabinets,
and wall louvers are installed properly for weatherproofing to seal out wind,
rain, snow, and insects.
6.3 Condensate from cooling coil is usually rejected in the condenser

air stream. Inspect units during time of high humidity (either high space
humidity or high outdoor humidity) to be sure that condensate is not staining
building exterior.
6.4 Turn unit controls to change outside damper positions to be sure

that dampers are operating properly. Dampers should be closed tightly when
units are off.
6.5 Inspection check list CL 8A-3 for packaged terminal air-conditioner

is included in the Appendix.
7. Fan.
7.1 For large units inspect fan housing access door and pressure
latches for tightness. Open and close doors to detect interference of door
with thermal insulation and other equipment.
7.2 Inspect bearing for proper oil or grease application. Grease lines
for bearings should extend to outside of duct connections with grease
fittings. Oiling shall not require dismantling of fans, ducts, or other
components if so specified in contract documents.
7.3 Inspect belt guard for access to oiling, speed counting device, and
other maintenance requirements.
Page 216
7.4 Observe fan steadiness during operation and excessive vibration

transmission to building supporting structure.
7.5 For outlet damper or inlet vane controls inspect control linkage
manually or by manipulating controller for the full range of the stroke. When
a single operator controls inlet vanes of double inlet fans, inlet vanes on
both inlet openings must move in unison. Inspect inlet vane rotation
direction with respect to that of the fan wheel.
7.6 Fans exposed to weather should have protective weather hoods over
motors and drives.
7.7 For fans without duct connections, unless they are housed in
plenums, they must be provided with protective devices for personnel safety
such as wire mesh or expanded metal screens at inlets and outlets.
8. Heating and cooling coils.

8.1 Inspect heat transfer fins for damages.
8.2 Inspect baffles between coils and casing to assure that air is not
bypassing coils.
8.3 Inspect cooling coil drain pans and drain pipes. For large units
with multi-coil assemblies, each coil must have individual pans with drain
pipes to avoid flooding of lower coils. Cooling coil drain traps must be
adequate for the static pressure imposed.
8.4 Inspect pipe fittings, valves, and coil accessories in accordance

with specifications and drawings. Included are water supply, water return,
steam supply, condensate return, air vents, and drains.
8.5 Inspect steam coils for possible coil freezing problem. Good
condensate draining must be provided: adequate slope of tubes, adequate
pressure head between coils and steam traps (minimum 18 in.), and vacuum
breakers at high position of coils. Adequate sizing of steam traps should be
checked if the requirements are not given in the contract specifications.
8.6 Steam main drips must be provided before coil connections.
8.7 Check temperature of steam traps and condensate piping for possible
steam leaks. They must not be unduly hot.
8.8 Inspect primary element installation for flow measurement devices,

if specified. The specified distance of pipe lengths and accessories (such as
water straightening devices) must be viewed as minimum requirements.
Page 217
9.
"
Air filters.
9.1 Inspect filters for air leakage between filters and holding frames
and between filter assembly and unit casing. Inspect positive sealing devices
for air leakage, if specified.
9.2 For large units with automatic renewable type air filters, inspect
medium advancing and override operation (pressure control, timer setting,
media switch, etc. See specifications for project requirements).
9.3 Inspect filter gage sensing tips and lines for correct static
pressure sensing.
9.4 For inclined manometer type filter gages check for correct
installation levels.
9.5 Filter holding frames must be anchored securely to air conditioning

unit casing.
9.6 Make sure adequate access spaces are provided for filter media
10.
replacement
9.7 Filter media must be new (clean) at the time of commissioning

inspection.
9.8 Check the number of spare filters provided by the contractor

against contract specification requirements.
Dampers.
11. 10.1 Verify that the blade arrangement, bearing material and edge
sealing material meet the requirement of the specifications.
10.2 Inspect full range of damper movement by manipulating actuator.

Verify damper closing position.
10.3 Felt strips should be provided for backdraft dampers. Dampers

shall not rattle during operation.
10.4 all dampers in ducts must have access doors in accordance with
specifications. Doors must be air tight.
Air louvers.
11.1 Verify material, arrangement, and dimensions.
11.2 Verify material and mesh size of bird or insect screens.
Page 218
12.
Casings.
12.1 Inspect casing for integrity.
12.2 Verify access door sizes, gasket tightness, and latch arrangement.
12.3 If required by contract documents, make sure flexible connections

are installed between air conditioning equipment and duct system. Check
13.
specifications for material and construction of flexible connections. Verify
that all pipings and conduits crossing the flexible connections also include a
flexible connection to maintain the integration of the connections.
Thermal insulation.
14. 13.1 Check thermal insulation for damages and omissions.
13.2 Material, thickness, and finish of thermal insulation and vapor

barrier must be as specified.
13.3 Check vapor barrier downstream of cooling coil for integrity.
Controls.
14.1 Most unitary units are selected with factory installed controls
to satisfy the requirements of contract specifications. The commissioning
team should be familiar with the specifications and manufacturer's operating
instructions to verify the control operations.
14.2 For units having pneumatic interface with building pneumatic

control systems, inspect interfacing devices (usually electric to pneumatic
devices or vice versa) to make sure that the correct transducing and control
are achieved.
Page 219
EXHIBIT 8-B TEST PROCEDURES FOR UNITARY AIR CONDITIONING UNITS
1. Scope. The test procedures described in this EXHIBIT apply to unitary

air conditioning units. Included equipment are packaged rooftop units,
computer room air conditioning units, and packaged terminal air conditioners
(PTAC)
a. ASHRAE Standard 37 (Method of Testing for Rating Unitary Air
Conditioning and Heat Pump Equipment) provides standard test methods for
determining the cooling capacity of unitary air- conditioning equipment and
the cooling and/or heating capacities of unitary heat pump equipment. Unitary
equipment is limited to electrically driven mechanical compression types. It
does not include testing method for room air-conditioners.
b. ASHRAE Standard 41.6 (Standard Method for Measurement of Moist Air

Properties) gives recommended practices and procedures for measurement and
calculations of moist air properties. It describes moisture measuring
instruments, the ranges of conditions these instruments are practical, their
accuracies, and the techniques of use to achieve desired accuracies. The
instruments included are psychrometer dew point hygrometer, heated electrical
,
salt-phase transition hygrometer, Dunmore type sensor, and electrolytic

hygrometer. Calibration and reference standards are also discussed.
c. ASHRAE Standard 58 (Method of Testing Room Air Conditioner Heating

Capacity) prescribes test methods for determining the heating capacities and
air flow quantities for room air conditioners equipped with means for room
heating. It is used to test through- the -wall window, or console air
,
conditioners
d. ARI Standard 210 (Unitary Air-Conditioning Equipment) provides

definitions, classifications, requirements for testing and rating, performance
requirements, safety requirements, and conformation conditions for
factory-made residential, commercial, and industrial air-conditioners or
matched assemblies with electrically-driven mechanical compressors. This
standard applies to units with cooling capacities less than 135,000 Btuh.
e. ARI Standard 310 (Packaged Terminal Air-Conditioners) applies to

factory-made residential, commercial, and industrial packaged terminal
air-conditioners. It provides definitions, classifications, standard
equipment, requirements for testing and rating, specifications, literature and
advertising requirements, performance requirements, design, construction and
assembly requirements for safety, and conformance conditions. This standard
does not apply to rating and testing of individual assemblies, such as a
Page 220
.
cooling or heating section, for separate use and may be used for systems with
a total external duct static resistance up to 24.9 Pa (0.1 inch of water).
f. ARI Standard 360 (Commercial and Industrial Unitary Air-Conditioning

Equipment) provides, for commercial and industrial unitary air-conditioning
equipment: definitions and classification; requirements for testing and
rating; specifications, literature and advertising requirements; performance
requirements; safety requirements; and conformance conditions. This standard
does not apply to unitary air- conditioners with capacities less than 135,000
Btuh
g. Associated Air Balance Council National Standards (National Standards

for Total System Balance) is an industry standard for establishing a minimum
set of field and balancing standards. This Standard together with the one in
paragraph h. below differ from all other standards listed here in that these
two standards are solely for field testing, adjusting, and balancing of HVAC
systems. This Standard describes measurement instruments and their use, some
basic system design information, and procedures for testing, adjusting, and
balancing of air and water systems. Detailed equipment testing is not
included.
h. National Environmental Balancing Bureau Standard (Procedural Standards

for Testing-Balancing-adjusting of Environmental Systems) is a standard
similar in purpose and practice to the previous standard for field testing,
adjusting and balancing of HVAC systems.
3. General.
3.1 Since the capacities of unitary air conditioning units in contract

specifications are for the entire assemblies and are rated by specifying the
air conditioning capacities (air flow rates, states of air, heating/cooling
capacities, etc.) and conditions of condensing media (water states and flow
rates for water cooled condensers, states of air for air cooled condensers,
etc.), verification of actual capacities under the specified conditions is the
main task of testing.
3.2 Limited testing of PTAC is recommended in this guide. This is

based on the following considerations:
3.2.1 Variations of equipment arrangement of PTAC is not large.
3.2.2 The contract specification usually requires that the units

be certified under the ARI Unitary Air-Conditioner Certification Program.
3.2.3 Accurate measurement of air flow rate in the field without

altering the unit performance is difficult for PTAC units.
Page 221
3.3 One of the important measurements in iôoftop and computer room air
conditioning unit testing is the measurement of supply air flow rates.
Depending on field duct arrangements of the project, temporary alteration of
ducts to accommodate measurement instruments may be necessary. However,
temporarily altering ductwork may be costly and should be done as a last
resort when the system is not meeting performance. Good practices for
measuring air flow should be followed (see Chapter 2 AND BASIC MEASUREMENT).
However, the duct alteration should not unduly change the unit performance.
3.4Functional inspection and test is based on the premise that the

construction contractor has tested, adjusted, and balanced the entire air and
water systems and is ready for normal operation. Certain preparatory
procedures listed in this section are needed before commencing functional
performance tests of units.
3.5 All architectural openings, such as windows and doors, should be at

their normally used positions (Check both architectural and mechanical
drawings)
3.6 All fans (supply, return, exhaust, transfer) which may influence
the air balance in the area should be operating at their normal conditions.
3.7 All system interlocks should be at their normal operational

condition.
3.8 All safety devices and provisions have been inspected and tested
already.
3.9 The space temperature and humidity controls should be set at normal
operating conditions.
3.10 Air flow rate measurement of fans and subsystems (if air flow
rates differ from that of the main fan) should be performed before other
tests
3.11 All manual damper positions as set by the construction contractor

should be marked before they are attempted to be changed for tests, so their
original positions may be restored, if necessary.
3.12 It should be recognized that most installations of air systems are

not at ideal conditions for flow measurements. Extraordinary caution and
details should be paid to the selection of sensor locations and measurement
techniques
3.13 Fan ratings supplied by fan manufacturers and air flow rates of
the design documents are generally in standard air conditions, approximately
dry air at 21.1 °C (70 °F) and 101.3 kPa (29.92 in. of Hg) or 1.20 kg/m 3
,
(0.0750 lb/cu. ft) unless noted otherwise. It is generally adequate to use

volumetric flow rates for commissioning purpose. If the temperature,
Page 222
humidity, and barometric pressure differ substantially from those of the

standard air, the volumetric flow rates from the test results must be
adjusted.
3.14 Check for dampers installed in main ducts that have no function in
balancing air between duct branches, set the blades of these dampers parallel
to the air flow, or have the dampers removed.
3.15 The preferred method of measuring air flow rate is the pitot tube
traverse method. It is extremely important in selecting the location in the
ducts for the pitot measurement. If packaged air flow measuring stations are
specified and installed, they should be used after a preliminary check of its
performance. Use SE-9 to 11 for air velocity measurement and SE-12 for volume
air flow rate.
4. Instrumentation.
4.1 Make sure that all instrumentation is in good working order and is
in calibration. See Chapter 2 AND BASIC MEASUREMENT for calibration of
instruments. Instrumentation calibration work sheet WS 8B-1 is included in
the Appendix.

by the contractor or equipment manufacturers may be used for performance
tests, if they meet the accuracy and calibration requirements of this Section.
4.3.1
(The glass thermometers installed on water pipes for maintenance purposes do
not usually meet the requirements for performance tests.)
4.3 The required measurement, minimum accuracies, and instruments

Temperature.
4. 3. 1.1 Entering and leaving condenser water temperature,

and entering and leaving hot water temperature of hot water humidifiers. The
measurement system error shall not exceed +/- 0.1 °C (0.2 °F) .
4. 3. 1.2 Temperature differential of entering and leaving

water for the applications of paragraph 4. 3. 1.1 above. Direct measurement of
this measurement is preferred over deducing the difference from separate
temperature measurements of entering and leaving water. The measurement
system error shall not exceed +/- 0.1 °C (0.2 °F).
4. 3. 1.3 Steam temperature of steam coils and steam

humidifiers. The measurement system error shall not exceed 0.6 °C (1 °F) .
Locate sensing device after steam control valves.
Page 223
4. 3. 1.4 Condensate temperature^ of steam coil. The

measurement system error shall not exceed 0.6 °C (1 °F) . Locate sensing
element after traps. If coils are individually trapped, temperature sensing
device should be in the combined condensate pipe.
4. 1.3. Entering and leaving air temperature of units. The

measurement error shall not exceed +/- 0.3 °C (0.5 °F) . Stratification is a
common phenomenon in air measurement. Since both the flow rate and
temperature distribution may vary across the coils or air plenums, it is
important to obtain the average temperature of the flow. At least one
measurement at each one square foot of coil face area or plenum
cross-sectional area shall be taken unless the measurement is for outside air
or the measurement is taken in a thoroughly mixed air stream.
4. 1.3. The temperature differential of entering and

leaving air. This measurement is preferred over deducing the difference from
separate temperature measurements of entering and leaving air in applications
of measuring air temperature differentials. The measurement system error
shall not exceed +/- 0.3 °C (0.5 °F) The precautions for measurements
.
described in the previous paragraph must be observed.
4. 1.3. Entering and leaving air relative humidity, wet

bulb temperature, or dew point temperature for cooling coils and humidifiers.
The total system measurement error shall not exceed +/- 0.6 °C (1 °F) wet bulb
or equivalent. The humidity conditions before and after a coil may also be
stratified. With certain instruments such as sling psychrometers it is
difficult to make multiply measurements across the face of the coil. Locations
away from coils should be selected for single humidity measurements.
4.3.2 Flow rate.
4. 3. 2.1 Water or steam flow rates for coils or humidifiers.

The total error of combined sensing and readout devices shall not exceed +/-
3% of specified flow rates. The minimum pipe length requirements must be
observed or flow straightener installed in accordance with the recommendations
of Chapter 2, AND BASIC MEASUREMENT.
4.3.3 Pressure.
4. 3. 3.1 Steam pressure. The measurement system error shall

not exceed +/- 689.5 Pa (0.1 psi). Steam pressure shall be measured after
steam control valve.
4. 3. 3. Pressure gages installed on pipes for the purpose

of maintenance operation may be used to measure the water pressure at inlet
and outlet of coils if they are calibrated and meet accuracy requirements. The
measurement error shall not exceed +/- 3.448 kPa (0.5 psig)
Page 224
3
4. 3. 3. Air static pressure -and total pressure measurement.

The measurement system error shall not exceed +/- 12.4 Pa (0.05 in. of water).
4.4 Instrumentation calibration test work sheet for air conditioning

systems, WS 8B-1, is included in the appendix.
5.1
5. Rooftop and computer room unit tests.

Air flow rate measurement. The total air flow rate of a system
must be measured and verified to meet specifications first before all other
measurements. Additionally, air distribution to individual outlets must also
be measured and verified.
5.1.1 Project specification for some fans (usually for large

units) are given in flow rate and static pressure pairs. The flow rates are
the actually required air quantities. The pressure requirements are only
estimates. After a construction project is balanced by the air balancing
contractor, the system should provide the specified flow rates at the finally
adjusted fan pressure. This pressure in most cases may be different from the
specified rates.
5.1.2 For smaller units without external ducts for air

distribution, external static pressure is not specified in the construction
specification. Therefore, only air flow rates need to be measured.
5.1.3 When fans are tested and rated in the laboratories, they
are tested under ideal inlet and outlet conditions as prescribed in the ASHRAE
(and AMCA) standards. In overwhelming cases of actual installations, the site
conditions of ducts (also called system effect factors) alter the fan
performance, sometimes substantially. The fan manufacturers base their
submittals on matching the performance of the laboratory (or allowed
equivalent) results (fan curves or tables) with estimated air friction (the
specified pressure head) Any mismatch between the laboratory performance and
.
the actual performance is corrected by adjusting and balancing of the entire

air system. Therefore, during commissioning process it is important that a)
the measured fan air flow rates satisfies the specified fan air flow rates; b)
all spaces receive their required air flow rates; and c) the measured fan
pressure heads not necessary equal the specified fan pressure heads.
5.1.4 There is no fixed rules which can be applied universally in

selection of measurement methods in determining air flow rates of fans. The
persons responsible for commissioning tests must use their judgement in
deciding the method or combination of methods for performing the test.
5.1.5 Using Pitot tube to traverse the main ducts of the air
conditioning unit is the preferred method. Make sure the air flow at the
location of measurement is steady (after the recommended minimum length of
Page 225
straight duct run or after straightening vanes). ^ See EXHIBIT 2-C, STP-5 for
measurement procedures.
5.1.6 For very large units, measuring air flow rates at coil face
or air filter face with anemometer may be used for supply fan measurement, if
good locations for pitot measurement can not be found. See EXHIBIT 2-C, STP-6
for measurement procedures
5.1.7 Caused by possible external and internal disturbances, air

flow rate, pressure, electric current rate, power consumption, and fan speed
measurements shall be repeated 5 times and the results averaged to represent
the fan performance.
5.1.8 Required measurement data:
1.8.1 Total supply air flow rate, Q, in m 3 /s (ft 3 /min).

5.
This is the only air flow measurement required for units without external
distributing ducts.
5. 1.8. Depending on ductwork arrangement of the air

conditioning unit (lacking inlet or outlet duct), the pressure measurement are
different. Consult EXHIBIT 2-B STANDARD EQUATIONS FOR CALCULATIONS for
measurement requirements of different duct systems. The majority of
installations have inlet and outlet ducts (or plenums) for fans. The
following pressures, all in units of Pa (in. of water) should be measured.
* Total pressure at fan inlet duct, P t (in)
* Total pressure at fan outlet duct, P t(out)
* Static pressure at fan inlet duct, PS ( in )
* Static pressure at fan outlet duct, P s(out)
* Velocity pressure at fan inlet duct, P v(in)
* Velocity pressure at fan outlet duct, P V (out)
* Barometric pressure.
5. 1.8. Voltage of electrical service, V
5. 1.8. Electric current, A
5. 1.8. Rotating speed of fan, rpm
5.1.9 It is the responsibility of the construction contractor to

supply a fan to meet the construction specifications and to adjust and balance
the entire air system. The entire air system must operate stably. During
Page 226
..
commissioning testing the commissioning team shtmld make sure that the system
stability is achieved by measuring the fan speed. Use a tachometer or
stroboscope (see EXHIBIT 2-A COMMONLY USED FIELD TEST INSTRUMENTS) to measure
the fan speed continuously for at least 3 minutes. The speed variation shall
not exceed 3%.
Test procedures for constant air volume systems.

5.1.10 5.1.10.1
Set the outside air damper at the minimum position

and the return air and relief air dampers at their appropriate positions.
5.1.10.2controls during test.
Disable damper automatic
Perform the required measurements listed in 5.1.8

above
5.1.10.3 Check air flow rates to individual spaces. Select

air outlets randomly throughout the entire duct system from the same air
conditioning unit. If 10% of the outlets checked is off for more than 10% of
the specified flow rates, a second set of 10% outlets shall be checked. The
entire air distribution system, including fans and all dampers, must be
rebalanced and testing repeated, if (i) any 10% of the outlets checked have
flow rates off +/- 15% from the specified flow rates; or (ii) the total of all
measured flow rates of these outlets is off +/- 10% from the total of the
design flow rates of the same outlets.
5.1.10.4 Set the outside air to 100% and other dampers

(return and relief dampers) to their appropriate positions.
5.1.10.6
5.1.10.5 Measure electric current rate. The motor current
rate must not be greater than the full load current shown on the motor mane
plate
Restore all damper controls.
5.1.11 Test procedures for variable air volume systems.
5.1.11.1 It is difficult, if not impossible, to know when

the system block loads occur. Fans of variable air systems can only be tested
to verify their capacities and energy rates in accordance to the specified
values despite that the pressure requirements are only estimated.
5.1.11.2 Set the outside air damper at 100% position and

the return air and relief air dampers at their appropriate positions. Disable
damper automatic controls during test.
5.1.11.3 Manipulate duct pressure sensors by applying

simulated pressure changes (thus change the fan curves on a volume -pressure
diagram) and manipulate the air volume controls of the first few air outlets
(thus change the system curves of the volume -pressure diagram). The contract
Page 227
specified fan duty point (volume flow rate and pressure ) may be obtained
during test. Repeated adjustment and measurement may be needed.
5.1.11.4
Perform the required measurements listed in 5.1.8
above
5.1.11.5 The electric current rate of the motor shall not

be higher than the name plate full load current.
5.1.11.6 Use similar procedures test variable air volume

return air fans
5.1.11.7 Restore all damper controls.
5.1.11.8 Randomly select a minimum of 10% of VAV units

which are supplied from the same air conditioning system. Measure the maximum
and the minimum supply air flow rates of these units by manipulating their
respective thermostats. If 10% of the selected units having their flow rates
(maximum and minimum) differ more than 10% of the specified flow rates, a
second set of 10% units should be selected and measured. The entire air
system must be rebalanced and testing repeated, if (i) any 10% of the units
measured have flow rates off +/- 15% from the specified flow rates; or (ii)
the total of all measured flow rates of the selected VAV units differs over
+/- 10% from the total of the design flow rates of the same units.
5.1.11.9 During the maximum and the minimum air flow rate
manipulation, verify the operation sequence of reheat coils (for units with
reheat coils), recirculating fans (for units with recirculating fans), and
other operational controls as required in the contract specifications.
5.1.11.10 Measure and verify the required duct static

pressure at the locations of each fan static pressure sensor.
5.1.11.11 Measure static pressure of at least 25% of all

branch ducts just before the last VAV unit of the branch to verify that the
pressure is within + 49.8 Pa (0.2" of water) of the specified minimum pressure
of the VAV units. If the static pressure is lower than the minimum pressure
required or more than the total of minimum pressure plus 49.8 Pa (0.2" of
water) the fan static pressure controller setting must be adjusted and duct
,
pressure retested. The selection the these 25% branches should be estimated
and judged by the Team that these branches may encounter extreme (high or low)
pressure during building load changes.
Page 228
. . 2
3

5.2
Cooling/heating measurement. --
5.2.1 Cooling/heating measurements should be performed after fan

measurements
Depending on the weather at the time of testing, false

5.2.2
cooling or heating loads may be needed to achieve the contract specified
entering air conditions to the unit. If false loads are not available at the
time of commissioning, the heating and cooling tests must be postponed till
the specified conditions may be maintained.
5.2.3 For cooling tests turn automatic controls to cooling. Make

sure the heating coils are locked out.
5.2.4 In addition to load conditions described in paragraph 5.2.2

above, the performance of cooling depends on the conditions of the condensing
media
5. 2. 4.1 For air cooled units measure outside air dry bulb
temperature. If the temperature is not within 1.1 °C (2 °F) of the contract
specified temperature the test shall be postponed unless the temperature is
within 5.6 °C (10 °F) of the contract specified temperature AND manufacturer's
capacity versus ambient temperature data are available for extrapolation.
5. 2. 4. For water cooled units measure the condenser

entering water temperature. Adjust flow balancing devices or other means, if
necessary, to within 0.6 °C (1 °F) of the contract specified entering water
temperature. This temperature shall be maintained during the test.
5.2.4. For water cooled units measure the condenser water

flow rate. Adjust flow balancing devices or other means if necessary, to
within 3 % of the contract specified flow rate. This flow rate shall be
maintained during the test.
5.2.5 In order to maintain steady state conditions, the cooling

control must be energized during the cooling capacity test.
5.2.6 Measure cooling coil entering air dry bulb temperature.

Temperature control of the air upstream of the coils may need to be adjusted
or false load varied to maintain this temperature within 0.6 °C (1 °F) of the
contract specified entering air dry bulb temperature. The adjustment of
upstream air temperature may need be performed in conjunction with adjustment
of upstream air humidity (see the following) paragraph.
5.2.7 Measure the coil entering air humidity (relative humidity,

wet bulb temperature, of dew point temperature). Usually humidity needs to be
added in the air by manipulating humidifier or false humidity load source.
The humidity must be maintained within 5% RH or equivalent of the contract
specified value.
Page 229
5.2.8 Run air conditioning units for- at least 20 minutes to prove

that the systems are under steady state conditions. Steady state condition is
achieved when three consecutive measurements of coil leaving air temperature,
at 10 minute intervals, do not differ more than 0.6 °C (1 °F)
5.2.9 Measure barometric pressure.
5.2.10 Measure condenser leaving water temperature for water

cooled units.
5.2.11 Measure condenser water pressure at condenser inlet and

outlet for water cooled units having specified condenser water pressure drops
larger than 29.86 kPa (10 ft of water).
5.2.12 Take three sets of coil air data at 5 minute intervals:
5.2.12.1 Entering air dry bulb temperature.
5.2.12.2 Leaving air dry bulb temperature.
5.2.12.3 Entering air relative humidity, wet bulb

temperature, or dew point temperature.
5.2.12.4 Leaving air, relative humidity, wet bulb

temperature, or dew point.
5.2.13 During heating capacity tests, make sure the cooling

operation of the units are locked out and the heating operation is on.
5.2.13.1 Measure water flow rate of water heated units.

Adjust balancing devices, if necessary, to within 3% of the contract specified
flow rate. This water flow rate shall be maintained during the test.
5.2.13.2 Measure entering water temperature of water coil.

Adjust, if necessary, to within 0.6 °C (1 °F) from the contract specified
temperature. This temperature shall be maintained during the test.
5.2.13.3 Measure steam pressure and temperature for steam

heated units. Check pressure and temperature against steam table to make sure
that steam is at least saturated and that the steam pressure after control
valve is at the specified pressure of the coil. If the indicated pressure is
more than +/- 6.89 kPa (1 psi) from that specified, the steam line pressure
controlling device must be adjusted. If the steam is less than saturated, it
must be brought to saturation conditions before test is continued. The
pressure and temperature of the steam shall be maintained during the test.
5.2.13.4 Measure steam flow rate to the coils. Adjust

manual or automatic valve, if necessary, to within 3% of the contract
specified flow rate. This flow rate shall be maintained during the test.
Page 230
.
5.2.13.5 For electrically heated units, make sure electric

coil controls are energized.
5.2.13.6 For gas heated units, make sure gas heaters are in
operation.
5.2.13.7 Measure entering air dry bulb temperature.

Temperature controls of the air entering the units may need to be adjusted or
false load varied to maintain this temperature within 0.6 °C (1 °F) of the
contract specified entering air dry bulb temperature.
5.2.13.8 Run the air conditioning units for at least 10

minutes to prove that the units are under steady state conditions. Steady
state condition is achieved when three consecutive measurements of coil
5.2.13.9at 5 minute intervals, do not differ more than 0.6 °C
leaving air temperature,
(1 °F) 5.3
Take three sets of air data at 5 minute intervals:
Humidifying capacity measurement.
5.3.1 This section concerns mostly with humidifiers for computer

room unitary air conditioning units. In most applications water vapor is
directly injected into the conditioned air stream. Therefore, the test is to
measure the moisture adding capacity by measuring the inlet and outlet
conditions of the air stream. It is similar to testing of unit cooling
capacities. Depending on the conditions of the moisture being added to the
air, a very small amount of heat energy of the water vapor may be giving to
the air stream as sensible heat.
5.3.2 Humidifiers should be tested after fan and cooling/heating

tests. All heating and cooling sources to the units must be turned off except
for the energy to operate the fans and humidifiers.
5.3.3 The test may be performed at any entering air temperature.

The commissioning team should be sure that the air leaving the humidifier
section do not reach 80% RH or cause damage to buildings and equipment.
5.3.4 Test procedures.
5. 3.4.1 For humidifiers injecting steam directly into the

air stream, measure steam pressure and temperature at steam supply pipe.
Check steam tables to make sure that steam is at least saturated and that the
steam pressure is at the specified pressure. If the indicated pressure is
more than +/- 6.89 kPa (1 psi) from that specified, the steam line pressure
Page 231
{TV AC FUNCTIONAL INSPECTION AND TESTING GUIDE
controlling device must be adjusted. Correct the- degree of steam saturation,

if the steam is less than saturated, before proceeding testing. The steam
pressure shall be maintained during the test. For other types of humidifiers,
follow equipment supplier's instructions to prepare the humidifiers for
testing.
5. 3. 4. Make sure all energy sources to the unit, except

for fan, control, and humidifier operation, are turned off.
5. 3.4. Adjust humidifier controls to full capacities.

Maintain full capacity during the test.
5. 3.4.4 Let system run for at least 5 minutes.
5. 3. 4. Take three sets of air data at 5 minute intervals:

3.4.6
dew point temperature.
* Leaving air, relative humidity, wet bulb temperature, or

dew point.
5. Observe the humidifier operation. There should not

be "spitting" of water into the air stream.
5.3.5 Test work sheet for humidifier is included in test work

sheets for air conditioning system component tests, WS 5B-2, in the appendix.
5.4 Air filter.
5.4.1 It is not feasible to test air filter efficiencies and dust

holding capacities in the field. They must be tested in the laboratories in
according with industry standards. See construction specifications.
5.4.2 For operational testing of air filters see EXHIBIT 5-A,

INSPECTION PROCEDURES FOR AIR CONDITIONING SYSTEMS.
Test work sheet WS 8B-2 included in the Appendix may be used for
5.5
rooftop and computer room units.
Page 232
. .
6. PTAC tests.
Test procedures described in this guide for PTAC are basically for
6.1
operational tests.
6.2 If the contract specification requires that the units be certified

under the ARI PTAC Certification Program, make sure the certification symbols
are displayed on the units.
6.3 Test procedures.
6.3.1 Turn unit control to system-on position. Unit fan should

be on.
6.3.2 Turn unit ventilation air control to off position.
6.3.3 Turn unit control to cooling position or set unit

thermostat 10 F below space temperature.
6.3.5
6.3.4 Measure unit discharge air after unit is in cooling
position for at least 5 minutes. This air should be below 15.6 °C (60 °F) .
The cooling coil should show condensation if the space dew point is over 10 °C
(50 °F)
Turn unit control to heating position or set unit

thermostat 5.6 °C (10 °F) above space temperature. If hydronic heating system
is used for the system, make sure the specified hot water temperature is
available
6.3.6 Measure unit discharge air after unit is in heating

position for at least 5 minutes. This air should be above 48.9 °C (120 °F) .
6.3.7 Turn unit control to ventilation position. The outside air

damper should be open.
6.4 Test work sheet WS 8B-3 included in the Appendix may be used for
PTAC units.
7. Calculation and evaluation of performance.

7.1 Air flow.
7.1.1 The measured total air flow rate of the unit must not be
less than the specified fan air flow rate. The motor current rate must not be
greater than the full load current shown on the motor mane plate.
7.1.2 Calculate the fan total pressure or fan static pressure

from pressure measurements, if pressure rating is specified in the contract
Page 233
documents. For the reasons stated in paragraphs'^.! above, this pressure

should be used for reference only, if the other data show that the fan
performance 7.1.3
is satisfied.
Air flow rates in construction documents and manufacturer's

literature are usually given in standard air conditions. Designers usually do
not adjust air properties for HVAC applications below 79.50 kPa (2000 ft)
altitude. Therefore it does not justify to adjust measured data for ordinary
heating and cooling application below this altitude. For applications above
2000 ft, the commissioning team should be careful in determining the basis of
7.2
air flow rates as required in the construction documents. The Team should
make sure that the measured data and the required rating are on the same
bases. For adjusting of air properties at higher altitudes, see EXHIBIT 2-B
Heating and cooling capacities.
7.2.1 For heating capacities, the entering and the leaving air
humidity are not required to be measured in this guide. The errors of the
enthalpies of air caused by this simplification are not significant if a 50%
RH entering air humidity is assumed. This assumption is justified for the
majority of HVAC
7.2.3 applications.
7.2.2 The construction documents should state the basis of unit

capacity. If the basis of air flow rates are not stated, assume they are for
standard air.
Calculation procedure.
7. 2. 3.1 Calculate the average entering and the average

leaving air dry bulb temperature from measured data.
7. 2. 3. Calculate the average entering and the average

leaving air relative humidity, wet bulb temperature, or dew point temperature
from measured data. For heating capacities, only entering air calculations
are needed.
7. 2. 3. Calculate the saturated water pressure of the

entering air, (P sw ) ent Pa (in. of Hg) knowing the entering air dry bulb
. ,
temperature, using SE-1.
7. 2. 3. Calculate the entering air vapor pressure, (Pw ) ent »
Pa (in. of Hg) knowing the measured humidity of entering air for cooling coil
,
or the assumed humidity (50% RH) of the heating coil, using SE-2.
7. 2. 3. Calculate humidity ratio of entering air, (W) ent ,
kg (lb) of vapor/kg (lb) of dry air, using SE-3.
7. 2. 3. Calculate enthalpy of entering air, (H) ent ,

J/kg
Page 234
. , , 8
9 5 ,
(Btu/lb) of air, using SE-4.
7 .2.3.7 Calculate enthalpy of leaving air, (H) lvg J/kg ,
(Btu/lb) of air, using SE-4. For cooling coil both the dry bulb temperature
and humidity are as measured. For heating coil assume the leaving air has the
same humidity ratio as the entering air (calculated in step 7. 2. 3. above).
Calculate specific volume of air, v (in cu ft/lb of

7. 2. 3.
air), using SE-5. The air temperature at the flow measurement location must
be used in this calculation.
Calculate mass flow rate of air, M, kg/s (lb/min)

7. 2. 3.
3 3
using SE-15. The measured volume air flow rate, Q, m /s (ft /min) is needed ,
in the calculation.
7.2.3.10 Calculate heating or cooling capacity of coil.
Capacity, J/s = M [(H) lvg - (H) ent ]

(For SI)
Capacity, Btu/h = 60 M [(H) lvg - (H) ent ]

(For Customary)
7.3
7.2.3.11 Calculate net air friction across coils for coils
having specified friction greater than 124.4 Pa (0.5 in. of water).
7.2.4 The tested unit capacity shall not be less than 95% of the
contract specified capacity.
7.2.5 The test air friction of coil shall not be greater than
110% of the contract specified air friction.
Humidifying capacities.
7.3.1 Calculate the average entering air and the average leaving
air dry bulb temperature from measured data.
7.3.2 Calculate the average relative humidity, wet bulb

temperature, or dew point temperature of the entering and the leaving air from
measured data.
7.3.3 Calculate the saturated water pressure of the entering air,

(P sw ) entl Pa (in. of Hg) knowing the entering air dry bulb temperature, using
SE-1
7.3.4 Calculate the entering air vapor pressure, (P w ) en f Pa (in.

of Hg) knowing the measured humidity, using SE-2.
7.3.5 Calculate humidity ratio of entering air, (W) ent ,

kg (lb)
of vapor/kg (lb) of dry air, using SE-3.
Page 235
7.3.6
Calculate the saturated water 'pressure of the leaving air,
( ^sw) Ivg >
Pa (in. of Hg) ,
knowing the leaving air dry bulb temperature, using
SE-1.
7.3.7 Calculate the leaving air vapor pressure, (P w ) lvg ,

Pa (in.
of Hg) ,
knowing the measured humidity, using SE-2.
7.3.8 Calculate humidity ratio of leaving air, (W) lvg ,

kg (lb) of
vapor/kg (lb) of dry air, using SE-3.
7.3.9 Calculate specific volume of air, v, m 3 /kg (ft 3 /lb), using

SE-5. The air temperature at the flow measurement location must be used in
this calculation.
7.3.10 Calculate mass flow rate of air, M, kg/s (lb/min), using

SE-15. The measured volume air flow rate, Q, m 3 /s (ft 3 /min), is needed in the
calculation.
7.3.11 Calculate humidifier capacity.
Capacity, kg/s = M [(W) lvg - (W) ent ]

(For SI)
Capacity, (lb/h) - 60 M [(W) lvg - (W) ent ] (For Customary)
7.3.12 The above calculated humidifier capacity shall not be less

than 95% of the contract specified capacity.
7.3.13 The humidifier shall not "spitting".
8. Air conditioning system operational tests. The control systems

of unitary air conditioning units are factory designed and equipped.
Depending on their applications and sizes, control strategies of these units
are usually not as complicated as some other field erected systems. Refer to
Chapter 5 test procedures (EXHIBIT 5-B TEST PROCEDURES FOR AIR CONDITIONING
SYSTEMS) for operational tests for systems specified with those controls, such
as economy cycles, warm-up cycles, etc.
Page 236
APPENDIX
APPENDIX
(Inspection Check Lists and Test Work Sheets)
Al
3 6
APPENDIX
INSPECTION CHECK LIST/TEST WORK SHEET Page
2.1 TEST WORK SHEET WS 2C-1 -- AIR FLOW RATE IN ROUND DUCTS ... A5
2.2 TEST WORK SHEET WS 2C-2 -- AIR FLOW RATE IN RECTANGLE DUCTS . A6
3.1 INSPECTION CHECK LIST CL 3A-1 -- CHILLER • • • A8
3.2 INSPECTION CHECK LIST CL 3B-1 -- HEAT REJECTION EQUIPMENT
(COOLING TOWER, EVAPORATIVE CONDENSER, AND AIR COOLED
CONDENSER) A12
3.3 TEST WORK SHEET WS 3C-1 -- INSTRUMENT CALIBRATION FOR COOLING
PLANT A14
3.4 TEST WORK SHEET WS 3C-2 -- CENTRIFUGAL CHILLER (SAFETY
CONTROL TEST) A16
3.5 TEST WORK SHEET WS 3C-3 -- CENTRIFUGAL CHILLER (AUXILIARY
EQUIPMENT TEST) A17
3.6 TEST WORK SHEET WS 3C-4 -- CENTRIFUGAL CHILLER (FULL LOAD
TEST) A19
3.7 TEST WORK SHEET WS 3C-5 -- CENTRIFUGAL CHILLER (* % PART
LOAD AND CAPACITY CONTROL TEST) A23
3.8 TEST WORK SHEET WS 3C-6 -- CENTRIFUGAL CHILLER ( COOLING
PLANT SYSTEM TEST) A27
3.9 TEST WORK SHEET WS 3D-1 -- RECIPROCATING CHILLER (SAFETY
CONTROL AND GENERAL OPERATIONAL TESTS) A28
3.10 TEST WORK SHEET WS 3D-2 -- RECIPROCATING CHILLER (FULL LOAD
TEST) A31
3.11 TEST WORK SHEET WS 3D- -- RECIPROCATING CHILLER (* %
PART LOAD TEST) A3
3.12 TEST WORK SHEET WS 3E-1 -- ABSORPTION CHILLER (GENERAL
OPERATIONAL TESTS) A40
3.13 TEST WORK SHEET WS 3E-2 -- ABSORPTION CHILLER (FULL OR PART
LOAD TEST) A42
3.14 TEST WORK SHEET WS 3F-1 -- COOLING TOWER A48
3.15 TEST WORK SHEET WS 3F-2 -- REFRIGERANT CONDENSER (AIR COOLED
OR EVAPORATIVELY COOLED) . A51
4.1 INSPECTION CHECK LIST CL 4A-1 -- BOILER A55
4.2 INSPECTION CHECK LIST CL 4A-2 -- FURNACE A61
4.3 TEST WORK SHEET WS 4B-1 -- INSTRUMENT CALIBRATION FOR BOILER
AND FURNACE A63
4.4 TEST WORK SHEET WS 4B-2 -- GAS AND OIL FIRED BOILER A65
4.5 TEST WORK SHEET WS 4B-3 -- ELECTRIC BOILER A75
4.6 TEST WORK SHEET WS 4C-1 -- GAS AND OIL FIRED AIR FURNACE . . . A79
4.7 TEST WORK SHEET WS 4C-2 -- ELECTRIC AIR FURNACE A81
5.1 INSPECTION CHECK LIST WS 5A-1 -- AIR HANDLING UNIT A83
5.2 TEST WORK SHEET WS 5B-1 -- INSTRUMENT CALIBRATION FOR AIR
HANDLING SYSTEMS A89
5.3 TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT
TEST),
FAN A91
A3
6.1 INSPECTION CHECK LIST CL 6A-1 -- EMCS ^ Alll

6.2 TEST WORK SHEET WS 6B-1 -- EMCS GENERAL A113
6.3 TEST WORK SHEET WS 6B-2 -- EMCS OVERALL PERFORMANCE TEST,
TEMPERATURE, HUMIDITY, AND PRESSURE . . A116
6.4 TEST WORK SHEET WS 6B-3 -- EMCS OVERALL PERFORMANCE TEST,
FLOW A118
6.5 TEST WORK SHEET WS 6B-4 -- EMCS OVERALL PERFORMANCE TEST, FOR
ENERGY CALCULATIONS . . A120
6.6 TEST WORK SHEET WS 6B-5 -- EMCS APPLICATION SOFTWARE TEST,
SCHEDULED START/STOP . A124
OPTIMUM START/STOP ..... A125
DUTY CYCLING A127
ELECTRICAL DEMAND LIMITING A128
DAY- NIGHT SETBACK .... A130
DRY BULB ECONOMY CYCLE A132
ENTHALPY ECONOMY CYCLE . A133
VENTILATION AIR CONTROL A135
HEATING/COOLING COIL TEMPERATURE RESET A137
HOT WATER TEMPERATURE RESET A138
CHILLED WATER TEMPERATURE RESET . A139
CONDENSER WATER TEMPERATURE RESET A141
7.1 INSPECTION CHECK LIST CL 7A-1 -- FIRE SAFETY IN HVAC SYSTEMS A143
7.2 INSPECTION CHECK LIST CL 7A-2 -- FIRE SAFETY CONTROLS IN HVAC
SYSTEMS WITHOUT SMOKE CONTROL CAPABILITIES A144
7.3 TEST WORK SHEET WS 7B-1 -- ZONED SMOKE CONTROL SYSTEM . . . A145
7.4 TEST WORK SHEET WS 7C-1 -- PRESSURIZED STAIRWELL SYSTEM . . A148
8.1 INSPECTION CHECK LIST CL 8A-1 -- ROOFTOP AIR CONDITIONING
UNIT A150
8.2 INSPECTION CHECK LIST CL 8A-2 -- COMPUTER ROOM AIR
CONDITIONING UNIT A155
8.3 INSPECTION CHECK LIST CL 8A-3 -- PACKAGED TERMINAL
AIR- CONDITIONER A159
8.4 TEST WORK SHEET WS 8B-1 -- INSTRUMENT CALIBRATION FOR UNITARY
AIR CONDITIONING UNIT A160
8.5 TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND COMPUTER ROOM
UNIT A162
8.6 TEST WORK SHEET WS 8B-3 -- UNITARY PTAC TEST A182
A4
:
APPENDIX
2.1 TEST WORK SHEET WS 2C-1 -- AIR FLOW RATE IN ROUND DUCTS
Air handling system no. Date
Duct designation no, Test agent
Size
Specified flow rate* cfm Commissioning team
Duct location
Notes for using form:

and subscript "s" denote data required from specification,
drawings, manufacturer's manuals or by calculations. Copy in blanks.
No. Steps
Velocity pressure readings: Velocity:

Horizontal diameter:
Ring 1 "w.c. fpm
Ring 2 "w.c. fpm
Ring 3 "w.c. fpm
Ring 4 "w.c. fpm
Ring 5 "w.c. fpm
Ring 5 "w.c. fpm
Ring 4 "w.c. fpm
Ring 3 _____ "w.c. fpm
Ring 2 "w.c. fpm
Ring 1 "w.c. fpm
Vertical diameter:
Ring 1 "w.c. fpm
Ring 2 "w.c. fpm
Ring 3 "w.c. fpm
Ring 4 "w.c. fpm
Ring 5 "w.c. fpm
Ring 5 "w.c. fpm
Ring 4 "w.c. fpm
Ring 3 "w.c. fpm
Ring 2 "w.c. fpm
Ring 1 "w.c. fpm
Average velocity fpm

7T
Air flow rate *= average velocity x x (dia. of duct) 2

4
measured air flow rate
% Error = (1 ) x 100%
specified air flow rate
COMMENTS
A5
2.2 TEST WORK SHEET WS 2C-2 — AIR FLOW "RATE IN RECTANGLE DUCTS
Page 1

Duct designation no. Test agent
Size
Duct location

1. and subscript "s" denote data required from specification, drawings,
manufacturer's manuals or by calculations. Copy in blanks.
2. Add rows/columns and positions as necessary.
No. Steps
Velocity pressure readings: Velocity:

First row or column:
Position 1 "w. c fpm
Position 2 "w c . fpm
Position 4 "w.c. fpm
Second row or column:

Third row or column:

Position 5 "w.c fpm
COMMENTS
A6
: ...
APPENDIX
TEST WORK SHEET WS 2C-2 -- AIR FLOW RATE IN REGTANGLE DUCTS (continued)
Page 2

Duct designation no. Test agent
Size
Duct location
No. Steps
Fourth row or column:

Position 1 "w c
.
fpm
Position 2 "w c
.
fpm
Position 3 "w c
.
fpm
Position 4 "w c
. fpm
Position 5 "w c
. fpm
Position 6 "w c
.
fpm
Fifth row or column:

Position 2 "w c
. fpm
Position 3 "w c
. fpm
Sixth row or column:

Position 5 "w.c fpm
Average velocity fpm
Air flow rate = average velocity x Duct width x duct depth
measured air flow rate

% Error « (1 ) x 100%
specified air flow rate
COMMENTS
A7
3.1 INSPECTION CHECK LIST CL 3A-1 -- CHTLLER

Page 1
Chiller no. Date

Make & model Inspection agent
Serial no. Commissioning team
Chiller type
Refrigerant
Condensing: Water Air Evap
NO. DESCRIPTION YES NO N/A REMARKS NO
For all chillers:

1 Operation and maintenance manuals complete 1
2 Video taping of 0 & M performed and accepted 2
by vendors
3 General appearances no apparent damage
, 3
4 Headroom around chiller adequate 4
5 Tube pulling space adequate 5
6 Other access space adequate 6
7 Proper vibration unit installation 7
8 Isolation valves and balancing valves 8
installed (unions, flanges)
9 Pipe fittings and accessories complete 9
10 Pipes not supported on chiller 10
11 Evaporator air vent provided 11
12 Water cooled condenser air vent provided 12
13 Evaporator drain extended to floor drain 13
14 Water cooled condenser drain extended to 14
floor drain
15 Refrigerant relief pipe extended to outside 15
16 Protection shields for motor and belts 16
17 Alignment of motor driven components 17
18 Belt tightness 18
19 Thermometers complete 19
20 Pressure gages complete 20
21 Flow meters meet installation requirements 21
22 Proper refrigerant type 22
23 Proper refrigerant level 23
24 No refrigernat leakage 24
25 Proper oil types 25
COMMENTS
A8
:
APPENDIX
INSPECTION CHECK LIST CL 3A-1 -- CHILLER (continued)

Page 2
Chiller no. Date
NO. DESCRIPTION YES NO N/A REMARKS NO.
26 Proper oil level 26

27 Piping type and flow direction labeled on
piping 27
28 Equipment labels affixed 28
29 Thermal insulation complete and no damage 29
30 Surface paint complete 30
31 Control wiring installed properly 31
32 Power wiring installed properly 32
33 All elec components grounded properly 33
34 Oil heater installed properly 34
35 Size of overcurrent heater in motor starter 35
36 Oil filter clean 36
37 No unusual noise & vibration when running 37
For centrifugal chillers only:
1 Check alignment for field assembled unit 1

2 Oil system temperature and pressure gages 2
complete
3 Compressor interlocking with oil pressure 3
4 Forced oil pump wired separatly 4
5 Adequate oil pressure when compressure 5
shaft is turning (incl. coastdown)
6 Oil cooling system piping system complete 6
7 Prerotation vane closed before comressor 7
reaches full speed
8 Prerotation vane steady when load changes 8
COMMENTS
A9
INSPECTION CHECK LIST CL 3A-1 -- CHILLER (contintted)

Page 3
Chiller no. Date
For reciprocating chillers only:
Oil pump wired separately from compressor

1 1
Interlocking between oil pressure and
2 2
compressure
3 Crankcase heater installed properly 3
4 Crankcase heater is on when compressor 4
power is off
5 Crankcase heater is off when compressor 5
is on
6 Oil has correct level before operation 6
7 Oil has correct level during operation 7
8 Oil not foaming excessively 8
9 For unit with remote condenser, check 9
pitch of refrigerant pipes and oil trap
10 For unit with air cooled condenser:
10a Adequate space for air circulation, 10a
no short circulation
10b Rotation direction of fan 10b
10c Air damper linkage adjustment 10c
11 For unit with evaporative condenser:
11a Adequate space for air circulation, 11a
no short circulation
11b Rotation direction of fan lib
11c Water level correct 11c
lid Float valve lid
lie Spray nozzle pattern lie
Ilf bleed valve adjustment Ilf
For absorption chiller only:
1 Automatic control line pressure 1

(pneumatically controlled unit only)
2 Steam control valve adjusted 2
3 Water control valve adjusted 3
4 Check solution pump strainer 4
5 Check refrigerant pump strainer 5
COMMENTS
A10
:
APPENDIX
INSPECTION CHECK LIST CL 3A-1 -- CHILLER (continued)

Page 4
Chiller no. Date
6 Check Steam or hot water pipe strainer

7 Check correct installation of steam trap
8 Obtain operating data from contractor to
decide if tube cleaning is necessary
9 Obtain charge data (lithium bromide and
additives)
10 Draw strong and week solution samples for
concentration analysis
11 Isolation valve for steam condensate 11
12 Isolation valve for hot water supply and 12
return lines
13 Pressure gages and thermometers
13a Hot water supply 13a
13b Hot water return 13b
13c Steam pressure gage 13c
For automatic tube cleaning system (ATCS) only:
1 Condenser water pump off:

la General appearance of ATCS, no apparent la
damage
lb Verify manual override (test one cycle) lb
1c Check diverter actuator speed setting lc
Id Verify indicating lights: Id
* Power on
* Diverter position
* Malfunctioning
le Verify cycle counter le
If Verify no interference with condenser If
flow switch
lg Check cycle timer settings lg
lh Check diverting valve lubrication lh
2 Condenser water pump on:
2a Manually initiate cleaning action 2a
2b Initiate cleaning action by resetting 2b
timer
COMMENTS
All
3.2 INSPECTION CHECK LIST CL 3B-1 ~

HEAT REJECTION EQUIPMENT
(COOLING TOWER EVAPORATIVE
,
CONDENSER, AND AIR COOLED CONDENSER)
Page 1
Equipment no. Date


Type: cooling tower
Evap condenser
Dry condenser
General

,
2
3 Air circulation space adequate 3
4 Equipment access space adequate 4
7 Pipe fittings, valves and accessories complete 7
8 Isolation valves installed 8
9 Balancing valves installed 9
10 Pipes supported on building structure member 10
11 Correct flow control device installation 11
(check valve, control valve, flow meter)
12 Thermometers and wells complete 12
15 Strainers or screens as specified 15
19 Lubrication properly applied 19
(motor and fan bearings, gear train)
20 Lubrication material as required 20
COMMENTS
A12
: .
APPENDIX
INSPECTION CHECK LIST CL 3B-1 -- HEAT REJECTION-EQUIPMENT (COOLING TOWER,

EVAPORATIVE CONDENSER, AND AIR COOLED CONDENSER) - continued Page 2
Equipment no Date

23 Piping type and flow direction labeled on
piping 23
24 Electic wiring installed properly 24
27 Direction of fan rotation 27
Cooling tower and evaporative condenser:

28 Water basin cleanliness 28
29 Drain terminated as specified 29
30 No excessive water carryover in air 30
31 Water level in basin correct 31
32 Proper float operation 32
33 Bleed valve adjusted corretly 33
34 No blockage to distribution orifices 34
35 Correct spray nozzle pattern 35
36 Correct balancing between cells 36
37 Correct balancing between towers 37
38 Correct balancing between condensers 38
39 Winterizing as specified 39
40 Railing, gratings, ladder adequate and secure 40
41 Material and installation as required 41
for field assembled towers
42 Tile support as required for tile filled towers 42
Air cooled and evaporatively cooled condensers:

43 Air damper mechanism operation . 43
COMMENTS
A13
3.3 TEST WORK SHEET WS 3C-1 — INSTRUMENT CALIBRATION FOR

COOLING
PLANT Page 1
Date
Test agent
Commissioning team

1. This work sheet is generally used for calibrating sensing devices and
instruments used in recording performance tests. Calibration of
functional and indicating devices for equipment operations are covered
under equipment test work sheets.
2. Standard instruments used for calibrating sensing devices must have
valid calibration. Record calibration data in Block A.
3. All instruments and sensing devices must be calibrated on bench or in
field with standard instruments. At least two points covering the
entire range of normal operation should be calibrated. This work sheet
lists recommended calibration points. After final calibration, record
data in Block B.
A. Standard instruments data (copy from standard instrument records):

Make, model & Calib. Calib. by
type serial no. Date (organization)
Temperature
Humidity
Pressure
Power
Others
B. Final calibration data (set temperature listed below may be changed

according to application)
Low point High point
Instrument Approx. Std Final Approx. Std Final

or sensing Calib Inst Calib Calib Inst Calib
No. Device Point Reading Reading Point Reading Reading No.
Temperature, F:
1 Water (for chilled, 32 200 1
condenser, steam
condensate, and hot)
2 Low pressure steam 200 300 2
3 Hot water for 200 300 3
absorption machine
4 Refrigerant for 100 200 4
remote condenser
A14
.. ::
APPENDIX
TEST WORK SHEET WS 3C-1 -- INSTRUMENT CALIBRATION FOR COOLING PLANT

(continued)
Page 2
Date

or sensing Set Inst Calib Set Inst Calib
No. Device Temp Reading Reading Temp Reading Reading No.
Air humidity:
5 Wet bulb temp, F 35//1 75#1 5
6 Relative humidity, % 30# 2 90# 2 6
Flow:
7 Flow sensing devices #3 #4 7
for water, steam, and refrigerant, gpm
a
b.
c ._
8 Pressure sensing devices, see Below 8
Pressure
9 Water static #5 #6 9
pressure, ft w.c. or psi
a
b.
c
10 Refrigerant static #7 #8 10
pressure, psi
a.
b.
c
11 Water pressure for 0 20 11
velocity sensing, in. w.c.
Other devices:
a
b.
#1 Within dry bulb temperature of 10 - 100 F

#2 Within dry bulb temperature of 35 - 100 F
y/3 25% below specified
#4 25% above specified
#5 25% below specified
y/6 25% above specified
#7 25 psig below specified
y/s 25 psig above specified
Comments
A15
3.4 TEST WORK SHEET WS 3C-2 — CENTRIFUGAL CHILLER (SAFETY

CONTROL TEST)
Chiller no .
Date
Make & model Test agent
Serial no. Commissioning team _
Motor serial no.
Refrigerant
1. Follow the steps outlined in the form and place check marks or
fill data as required. Initial under "pass” or "fail" colums,
supply remarks if necessary.
2. * denotes data required from specification, drawings, manufac-
turer's manuals or by calculations. Copy in blanks.
Check Fail &

No. Steps mark Pass Remarks No.
1 Check compressor electric voltage balance:

la Between phases 1 & 2: V (A) la
Between phases 2 & 3: V (B)
Between phases 1 & 3: V (C)
lb Calculate average voltage lb
(A + B + C) / 3 “ V (D)
lc Calculate deviation lc
(A - D) / D x 100 = % (E)
(B - D) / D x 100 - _% (F)
(C - D) / D x 100 - X (G)
Id E, F, or G not over +/- 1% Id
2 Disconnect power to compressor 2
3 Connect power to control panel 3
4 Test pilot lights and alarms 4
5 Turn compressor on (simulated) 5
6 Test refrig low temp cutout (* F) 6
Actual cutin F, Cutout F
7 Test refrig high temp cutout (* F) 7
8 Test ch w low temp cutout (* F) 8
9 Test oil heater thermostat (* F) 9
Actual cutin F, Curout F
10 Test cond high pres cutout (* psi) 10
Actual cutout pres psi
11 Test evap low pres cutout (* psi) 11
Actual cutout pres psi)
12 Test condenser water flow switch 12
13 Test evaporator water flow switch 13
14 Reconnect compressor wiring 14
15 Test low oil pressure safety control circuit 15
A16
: ,
APPENDIX
3.5 TEST WORK SHEET WS 3C-3 — CENTRIFUGAL CHILLER (AUXILIARY

EQUIPMENT TEST) Page 1
Chiller no. Date
Motor serial no.
Refrigerant __
fill data as required. Initial under "pass" or "fail" colums
Check Fail &

1 Start cond water pump 1

2 Balance cond water flow rate (* gpm) 2
Actual flow rate ( gpm)
3 Check ent cond water temp (* F) 3
Actual temp ( F)
4 Start ch water pump 4
5 Balance ch water flow rate (* gpm) 5
Actual flow rate ( gpm)
6 Check control air pressure 6
Actual pressure ( psi)
OIL SYSTEM:
7 Check oil level 7
8 Turn on oil pump 8
9 Check oil sump temp (* F) 9
Actual temp ( F)
10 Check oil temp at bearing (* F) 10
Actual temp ( F)
11 Check oil press at bearing (* psi) 11
Actual pressure ( psi)
PURGE SYSTEM:
12 Turn purge system to manual control 12
13 Test by following mfg recommendations 13
COMMENTS
A17
TEST WORK SHEET WS 3C-3 -- CENTRIFUGAL CHILLER (AUXILIARY EQUIPMENT TEST)

- (continued) Page 2
Chiller no. Date

14
Check Fail &
No. Steps mark Pass Remarks No
PUMPOUT SYSTEM:
Test by following mfg recommendations 14
If reciprocating compressor is provided:
14a Turn pumpout system condenser water 14a
valves on
14b Run pumpout compressor for 1/2 hour 14b
14c Record and compare running conditions 14c
with recommendations:
Discharge pressure (* psi/ psi)
Suction pressure (* psi/ psi)
Oil pressure (* psi/ psi)
Ent water temp (* F/ F)
Lvg water temp (* F/ F)
BRUSH CLEANING SYSTEM:

15 Attach thermometers and insulation at 15
both side of diverting valve
16 Take 3 sets of temperature readings 16
F, F, F
17 Compare measured temperature 17
Temp difference not to exceed 0.5 F
COMMENTS
A18
APPENDIX
3.6 TEST WORK SHEET WS 3C-4 — CENTRIFUGAL CHILLER (FULL LOAD

TEST) Page 1
Chiller no. Date

Motor serial no.
Refrigerant

fill data as required. Initial under "pass" or "fail" colums,
Check Fail &

No. Steps Mark Pass Remarks No.
1 Be sure cond w and ch w pumps are on 1

2 Set lvg ch w temp to specified (* F) 2
3 Turn on compressor 3
4 Observe direction of comp rotation 4
5 Load chiller by adding false load 5
and/or valving action using ch w
temp diff and comp current draw
as guide
6 Electric current not exceed demand 6
limit
7 Observe compressor vane actuator 7
No hunting appeared
8 Run chiller at full load for 1 hr 8
minimum with temp and flow rate
stablized as specified, minor
adjustment may be necessary
9 Take 3 sets of data at 10 min intervals 9
to verify system stablization:
tolerances from specified values not to
exceed 1 F for temp and 5% for flow
rate. Specified values:
Lvg ch w temp (* F)
Ent ch w temp (* F)
Ch w flow rate (* gpm)
Ent cond w temp (* F)
Lvg cond w temp (* F)
Cond w flow rate (* F)
A19
TEST WORK SHEET WS 3C-4 -- CENTRIFUGAL CHILLER (FULL LOAD TEST) - (continued)
Page 2
Chiller no. Date
Check Fail &

1 2 3
9a Chilled water: 9a
Lvg ch w temp ( ,
F) ,
Ent ch w temp ( ,
F) or ,
Ch w temp diff ( F)
Ch w flow rate ( gpm)
,
9b Condenser water: 9b
Lvg cond w temp ( F)
Ent cond w temp ( F) or
Cond w temp diff ( F) , ,
Cond w flow rate ( gpm)

10 Repeat step 9 if necessary until 10
differences between 3 readings are less
than the limits.
11 Take 3 sets of test data at 10 minute 11
intervals: tolerances from specified
values not to exceed 1 F for temp
and 5% for flow rate
1 2 3
Lvg ch w temp ( F)
Ent ch w temp ( F) or
Ch w temp diff ( F)
Ch w flow rate ( , ,
gpm)
Ent ch w press ( psi)
Lvg ch w press ( psi)
Evaporator lvg refrigerant
temperature ( F)
lib Condenser water: lib
Cond w temp diff ( F)
Ent condw press ( psi)
Lvg cond w press ( psi)
Cond lvg refrigerant
temperature ( , , F)
11c Electricity: 11c
Wattmeter output ( Watt)
12 No unusual noise during test 12
A20
:
APPENDIX
TEST WORK SHEET WS 3C-4 -- CENTRIFUGAL CHILLER -/FULL LOAD TEST) - (continued)
Page 3
Chiller no. Date
Check Fail &

13 Calculate average test data: 13

Lvg ch w temp ( F)
Ent ch w temp (
_F) or
Ch w temp diff (
F)
Lvg evap refrignt temp ( F)
Lvg cond refrignt temp ( F)
Ent cond w press ( psi)
14 Calculate full load capacity & performance: 14
14a Calculations: 14a
Test capacity
(CAP) t = (ch w temp diff) x (ch w flow rate) x 500 Btu/h
(ch w temp diff) x (ch w flow rate)

cooling tons
24
( ) x ( )
cooling tons
24
Specified capacity (CAP) S = * Btu/h or

= * cooling tons
Test power input (E) t = kW
Specified power input (E) s

= * kW
COMMENTS
A21
TEST WORK SHEET WS 3C-4 -- CENTRIFUGAL CHILLER (FULL LOAD TEST) continued
Page 4
Chiller no. Date_
Check Fail &

Test energy performance kW/ton

(CAP) t in tons
kW/ton
Specified energy performance kW/ton
Test evaporator water pressure drop

(Pevap) t *= water press at evap inlet - water pressure
at evap outlet
= - _____ = ft w.c.
Specified evaporator water pressure drop (P eva p)s “ * ft w.c.
Test condenser water pressure drop

(Pcond)t “ water press at cond inlet - water pressure
at cond outlet
“ _____ - - _____ ft w.c.
Spec ified condenser water pressure drop (P conci) s -= * ft w.c.
14b Acceptance criteria: 14b
(CAP) t > ( CAP s

(E) t < (E) s
Test energy performance > Specified energy performance
(
e vap) t ^ (P e vap)s
(E concj)t ^ ( E C ond ) s
COMMENTS
A22
: :
APPENDIX
3.7 TEST WORK SHEET WS 3C-5 —

CENTRIFUGAL CHILLER (* % PART
LOAD AND CAPACITY CONTROL TEST) Page 1

Serial no, Commissioning team
Motor serial no.
Refrigerant

Check Fail &

1 Ent cond w temp of certain part load 1

may be different from that of full
load (See specs.). If so, reset
cooling tower control to supply the
required ent cond w temp (* F)
2 Reduce chiller load by decreasing false 2
load and/or valving action using ch w
temp diff and comp current draw
as guide
3 Run chiller at desired part load for 3
1 hr minimum with temp and flow rate
4 Observe amperage readings of compressor 4
while load is being reduced. Readings
should not fluctuate
to verify system stablization
tolerances from specified values not
to exceed 1 F for temp and 5% for
flow rate. Specified values:
Lvg ch w temp (* F)
Ent ch w temp (* F)
Cond w flow rate (* gpm)
COMMENTS
A23
TEST WORK SHEET WS 3C-5 -- CENTRIFUGAL CHILLER (* % PART LOAD AND

CAPACITY CONTROL TEST) continued Page 2
Chiller no. Date
Check Fail &

1 2 3
i Chilled water: 5a
Lvg ch w temp ( ,
F)
Ch w temp diff ( ,
F) or
Ent ch w temp ( ,
F)
Ch w flow rate ( RPm)
1 2 3
> Condenser water: 5b
Ent cond w temp ( F)
,
Cond w temp diff ( F) or

,
Cond w flow rate ( RPm), ,
Repeat step 7 until the differences 6

between the 3 readings are less than
the limits.
Take 3 sets of test data at 10 minute 7
1 2 3
l Chilled water: 7a
Lvg ch w temp ( F)
Ent ch w temp ( ,
F) or ,
Ch w temp diff ( F)
,
Ch w flow rate ( RPm) ,
i Condenser water: 7b
Cond w flow rate ( RPm), ,
: Electricity: 7c
, ,
8 After all part load tests, remove false 8

load and/or restore valves to their
normal operating conditions
COMMENTS
A24
: )
APPENDIX
TEST WORK SHEET WS 3C-5 -- CENTRIFUGAL CHILLER -f-

* % PART LOAD AND CAPACITY
CONTROL TEST) continued Page 3
Chiller no. Date
Check Fail &

9 Turn lvg ch w thermostat up till 9

compressor starting coastdown. Then
restore this thermostat to its
original position, count time between
compressor coastdown and restart
(* min .
Actual delay time min.

10 During entire part load tests, no 10
unusual noise, vibration and
fluctuating compressor current draw
11 Turn compressor off, record oil press 11
at bearing (required minimum * psi)
Actual bearing oil pressure ( psi)
Lvg ch w temp ( F)
Ch w temp diff ( F) or
Ent ch w temp ( F)
COMMENTS
TEST WORK SHEET WS 3C-5 -- CENTRIFUGAL CHILLER (* % PART LOAD AND CAPACITY
CONTROL TEST) continued Page 4
Chiller no. Date
Check Fail &

13 Calculate part load capacity & performance: 13

Test capacity
(CAP) t - (ch w temp diff) x (ch w flow rate) x 500 Btu/h

- cooling tons
24
x
cooling tons
24
Specified capacity (CAP) S *= * Btu/h or
_ * cooling tons
Test power input (E) t - kW
Specified power input (E) s = * kW
(E) t
Test energy performance = kW/ton
(CAP) t in tons
kw/ton
Specified energy performance - * kW/ton
(CAP t > (CAP s

(E) < (E) s
t
COMMENTS
A26
: ,
APPENDIX
3.8 TEST WORK SHEET WS 3C-6 — CENTRIFUGAL CHILLER ( COOLING

PLANT SYSTEM TEST)
Chiller no. Date

Motor serial no.
3.
Refrigerant

Cooling plant system tests depend very much on system design
of the project. The steps of this form may need modification.
Consult specification and dwgs for changes needed.
Check Fail &

1 Test chiller, ch w pump, cond w 1

pump, and cooling tower interlock
(See specification and dwgs for
interlocking arrangement)
2 Test lead- lag machine by changing 2
sequencing switch positions and
observing chiller operation
3 If system has automatic start by sensing 3
outside air temp, place outside temp
sensor in liquid temp bath at specified
temp (* F) Verify chiller start.
.
Actual temp chiller starts F.

4 If system has timer operated automatic 4
start, turn timer to starting time
to verify chiller start.
COMMENTS
A27
3.9 TEST WORK SHEET WS 3D-1 —

RECIPROCATING CHILLER (SAFETY
CONTROL AND GENERAL OPERATIONAL TESTS) Page 1
Chiller no. Date

Serial no .
Commissioning team
Motor serial no.
Refrigerant
Condens ing Water: Air Evap
Compressor voltage (phase 1-2) V
Compressor voltage (phase 1-3) V
Compressor coltage (phase 2-3)__ V

Check Fail &

1 Check electric voltage balance:

la Between phases 1 & 2: V (A) la
Between phases 2 & 3 V (B)
Between phases 1 & 3 V (C)
lb Calculate average voltage lb
(A + B + C) / 3 = V (D)
lc Calculate deviation lc
(A - D) / D x 100 - % (E)
(B - D) / D x 100 = 1 (F)
(C - D) / D x 100 = 1 (G)
Id E, F, or G not over +/- 11 Id
2 Check crankcase heater status 2
(feel compressor warmth)
3 Check compressor oil level 3
4 Test all pilot lights and alarms 4
5 Start condenser water pump (water 5
cooled)
6 Check and adjust condenser water flow 6
rate (water cooled) (* gpm) gpm
7 Check condenser water temp (water 7
cooled) (* F) F
8 Start evaporative cooler (evaporatively 8
cooled)
COMMENTS
A28
: :
APPENDIX
TEST WORK SHEET WS 3D-1 -- RECIPROCATING CHILLER (SAFETY CONTROL AND GENERAL
OPERATIONAL TESTS) continued Pa S e 2
Chiller no._ Date
Check Fail &

9 Start chilled water pump 9
10 Check and adjust chilled w flow rate 10

11 Set and check chilled w temperature 11
(* F) F
12 Start compressor 12
13 Only first step cylinder loaded when 13
compressor is started
14 Check direction of condenser fan 14
ratation (air cooled and evaporatively
cooled)
15 Test temperature safety controls (if
provided)
15a Refrig low temp cutout (* F) 15a
15b Refrig high temp cutout (* F) 15b
15c Ch w low temp cutout (* F) 15c
15d Oil heater thermostat (* F) 15d
Actual cutin F, Curout F
16 Test flow safety controls: 16
16a Chilled water flow switch
16b Condenser waterflow switch
17 Test pressure safety controls:
17a High pres cutout (* psi) 17a
Actual cutout pres psi
17b Low pres cutout (* psi) 17b
Actual cutout pres psi)
18 Check oil level and foaming, record 18
oil pressure (if gage is provided)
psi (recommended * psi)
19 Check refrigerant charge through 19
sight glass
20 Load machine by adding false load 20
and/or valving operation
COMMENTS
A29
TEST WORK SHEET WS 3D-1 -- RECIPROCATING CHILLER "( SAFETY CONTROL AND GENERAL
OPERATIONAL TESTS) continued Page 3
Chiller no. Date
Check Fail &

21 Observe chilled water return temp vs. 21

cylinder loading
22 Observe electric current draw, it 22
shall not exceed maximum
23 Check discharge pressure for over- 23
charge
24 Test head pressure control (air cooled 24

and remote condenser)
24a Temperature sensed control
24b Pressure sensed control
25 Test lead-lag control 25
26 Test automatic start control:
26a Outside air temperature operated 26a
(* F) F
26b Timer operated 26b
COMMENTS
A30
:
APPENDIX
3.10 TEST WORK SHEET WS 3D-2 — RECIPROCATING CHILLER (FULL LOAD

TEST) Page 1
Chiller no. Date

Make & model_ Test agent
Motor serial no.
Refrigerant__

Check Fail &

1 Add false load til chiller is 1

fully loaded
2 Adjust and check chilled water flow 2
rate (* gpm) gpm
3 Adjust and check condenser water 3
flow rate (water cooled)
(* gpm) gpm
4 Adjust and check discharge pressure, 4
(air cooled and evaporatively cooled)
(* psi) psi
5 Find equvilent saturated discharge 5
temperature, F (air cooled and
evaporatively cooled)
6 Run chiller at full load for 1 hr 6
COMMENTS
A31
:
TEST WORK SHEET WS 3D-2 -- RECIPROCATING CHILLER FULL LOAD TEST) continued
Page 2
Chiller no. Date
Check Fail &


to verify system stablization: tolerances
from specified values not to exceed 1 F
for temp and 5% for flow rate
Specified values for all units:
Lvg ch w temp (* F)
Ent ch w temp (* F)
For water cooled units:
For air cooled units:
Saturated discharge pressure (* psi)
7a Chilled water:
12 3
7a
Lvg ch w temp (_ ,
F)
Ent ch w temp ( F)
gpm)
7b For water cooled condenser: 7b
7c For air or evap cooled condenser: 7c
Saturated discharge pressure
( psi)
Saturated discharge temperature
( F)
than the limits.
COMMENTS
A32
:
APPENDIX
TEST WORK SHEET WS 3D- 2 -- RECIPROCATING CHILLER, (FULL LOAD TEST) continued
Page 3
Chiller no. Date
Check Fail &


9a Chilled water:
12 3
9a
Lvg ch w temp ( 9 y
F)
Ch w temp diff ( y y
F) or
Ent ch w temp ( y y
F)
Ch w flow rate ( y y KPm)
Ent ch w press ( 9 y
psi)
Lvg ch w press ( y y
psi)
9b Electricity: 9b
Wattmeter output ( , ,
Watt)
9c Water cooled condenser: 9c
Ent cond w temp ( y y
F)
Cond w temp diff ( y y
F) or
Lvr cond w temp ( y y
F)
Cond w flow rate ( y y gP m )
Ent cond w press ( y y
psi)
Lvg cond w press ( y y
psi)
Air or evap cooled condenser:

12 3
9d
( psi)
( y y
F)
Ambient air dry bulb temperature
( y y
F)
Ambient air wet bulb temperature
( y y
F)
COMMENTS
A33
: : .
TEST WORK SHEET WS 3D- 2 -- RECIPROCATING CHILLER ^ FULL LOAD TEST) continued
Page 4
Chiller no. Date
Check Fail &

No, Steps Mark Pass Remarks No
10 Calculate average test data 10

Lvg ch w temp ( F)
Ent ch w temp ( F)
Lvg ch w press ( Psi)
10b Electricity: 10b
10c Water cooled condenser *
10c
Ent cond w press ( psi)
lOd Air or evap cooled condenser: lOd
Saturated discharge temp ( F)
Ambient air dry bulb temp ( _F)
Ambient air wet bulb temp ( F)
11 During entire full load tests, no 11
unusual noise, vibration
12 Calculate full load capacity & performance: 12

Test capacity

cooling tons
24
cooling tons
24
COMMENTS
A34
:
APPENDIX
TEST WORK SHEET WS 3D-2 -- RECIPROCATING CHILLER (FULL LOAD TEST) continued
Page 5
Chiller no. Date
Check Fail &


= * cooling tons
Test power input (E) t = _kW
Specified power input (E) s = * kW
(E) t
(CAP) t in tons
kW/ton
Specified energy performance = *

(P evap ) t “ water press at evap inlet - water press
at evap outlet
*= - = ft w.c.
Specified evaporator pressure drop (P eva p)s = * ft w.c.
Test condenser water pressure drop (water cooled only)

(Pcond)t = water press at cond inlet - water press
at cond outlet
= - = ft w.c.
Specified condenser pressure drop (P cond ) s = * ft w.c
12b Acceptance criteria:
(CAP) t > (CAP) s

(E) t < (E) s
(Pevap)t ^ (êvap)s
( P cond ) t < ( p cond)s (water cooled only)
COMMENTS
:
3.11 TEST WORK SHEET WS 3D-3 — RECIPROCATING CHILLER (* %

PART LOAD TEST) Page 1
Chiller no. Date

Motor serial no.
Refrigerant

Check Fail &

1 Reduce chiller load to specified 1

part load and adjust condenser water
temp (water cooled) or saturated
discharge temp (air or evap cooled)
to specified or those of the Manual
2 Run chiller at part load for 1 hr 2
to verify system stablization:
to exceed 1 F for temp and 5% for
flow rate
Specified values for all units:
Lvg ch w temp (* F)
Ent ch w temp (* F)
For water cooled units:
For air cooled units:
Saturated discharge pressure (* psi)
COMMENTS
A36
. : 3
APPENDIX
TEST WORK SHEET WS 3D- -- RECIPROCATING CHILLER (* % PART LOAD TEST)

continued Page 2
Chiller no Date
Check Fail &

No Steps Mark Pass Remarks
3a Lvr ch w temp (
12 3
F) 3a
Ch w temp diff ( ,
F) or
Ent ch w temp ( F)
3b Water cooled Condenser: 3b
Ent cond w temp ( , ,
F)
Lve cond w temp ( F)
3c Air or evap cooled condenser: 3c

( psi)
( F)

than the limits.
5a Chilled water:
12 3
5a
Lvg ch w temp ( , ,
F)
Ch w temp diff ( , ,
F) or
Ent ch w temp ( , ,
F)
gpm)
COMMENTS
: :
TEST WORK SHEET WS 3D- 3 -- RECIPROCATING CHILLER H* % PART LOAD TEST)

continued Pag® 3
Chiller no. Date
Check Fail &

5b Electricity: 5b
Wattmeter output ( , ,
Watt)
5c Water cooled condenser: 5c
F)
Cond w temp diff ( , ,
F) or
Lvg cond w temp ( , ,
F)
Cond w flow rate ( gP m )
5d Air or evap cooled condenser: 5d
( psi)
( F)
Ambient air dry bulb temperature
( F)
Ambient air wet bulb temperature
( F)
6 Calculate average test data 6
Lvg ch w temp ( F)
Ent ch w temp ( F)
6b Electricity: 6b
6c Water cooled condenser l 6c
6d Air or evap cooled condenser: 6d
Saturated discharge temp ( F)
Ambient air dry bulb temp ( F)
Ambient air wet bulb temp ( _F)
COMMENTS
A38
: ) ) .
APPENDIX
TEST WORK SHEET WS 3D-3 -- RECIPROCATING CHILLER (* % PART LOAD TEST)

continued Page 4
Chiller no. Date
Check Fail &

No, Steps Mark Pass Remarks No
7 During entire part load tests, no

unusual noise, vibration
8 Calculate part load capacity & performance: 8
8a Calculations: 8a
Test capacity

cooling tons
24
cooling tons
24

= * cooling tons
Test power input (E) t = kW
Specified power input (E) s *= * kW
(E) t
(CAP) t in tons
kW/ton
Specified energy performance = * kW/ton
( CAP t > (CAP s

(E) t < (E) s
COMMENTS
:
3.12 TEST WORK SHEET WS 3E-1 ~ ABSORPTION CHILLER (GENERAL

OPERATIONAL TESTS) Page 1
Chiller no. Date

Serial no .
Commissioning team
Energy source: Steam psi
Hot water F

Check Fail &

1 Test low temp cutout (* F) 1

Actual cutin F, cutout F
2 Test other temp safety control (See 2
specs for requirements) (* F)
10
Actual cutin F, cutout_ F
3 Check interlocking of ch w cond w 3
pumps and cooling tower (See spec
and dwgs for requirements)
4 Test flow safety control:
4a Chilled water flow switch 4a
4b Condenser water flow switch 4b
5 Test pilot lights and alarms 5
6 Adjust and check chilled water 6
flow rate
7 Adjust and check condenser water 7
flow rate (* gpm) gpm
8 Start chiller 8
9 Apply load gradually until chiller 9
is fully loaded
If steam is energy source and demand 10
limit is specified, check steam flow
rate (* % full load) _____ Ib/h
COMMENTS
A40
:
APPENDIX
TEST WORK SHEET WS 3E-1 -- ABSORPTION CHILLER ('GENERAL OPERATIONAL TESTS)

continued Page 2
Chiller no. Date
Check Fail &

11 After chiller is operating under 11

stable conditions, withdraw solution
samples from generator and absorber
12 Analyze sample concentration and 12

.
compare with manufacturer's
recommendations
Generator (* %) %
Absorber (* %) %
13 Operate purge system and check for 13
hydrogen presence, purge system
should be on for at least 1 hr
14 Determin fouling condition 14
of condenser tubes (See Guide)
COMMENTS
A41
: ,
3.13 TEST WORK SHEET WS 3E-2 — ABSORPTION CHILLER (FULL OR PART

LOAD TEST) Page 1
Chiller no .
Date
Make & model_ Test agent
Energy source: Steam psi
Hot water F
Load: Full load % part load
,

Check Fail &

1 Adjust machine load and chilled 1

water temp setting to the desired
testing load and temp (* F) F
2 Check and adjust chilled water flow 2

rate (* gpm) _____ gpm
3 Check and adjust condenser water 3
flow rate (* gpni) gpm
4 Adjust condenser water temp control 4
to obtain specified temp entering
absorber (* F) _____ F
5 For chiller with hot water as energy 5
source, measure and adjust water temp
to specified (* F) F
6a For chiller with steam as energy 6a
source, measure steam pressure at
control valve (* psig) ____ psig
6b Measure steam temp at control valve 6b
F
6c Determine quality of steam from 6c
steam table, it must be saturated
or superheated
7 Run chiller for 1 hr minimum with temp 7
and flow rate stablized as specified,
minor adjustment may be necessary
COMMENTS
A42
: : : .
APPENDIX
TEST WORK SHEET WS 3E-2 -- ABSORPTION CHILLER (-PULL OR PART LOAD TEST)
continued
Page 2
Chiller no. Date
Check Fail &

No. Steps Mark Pass Remarks No
8 Take 3sets of data at 10 min intervals 8
to verify system stablization

to exceed 1 F for temp, 5% for flow
rate, and 0.2 psig for steam pressure
Specified values:
Lvg ch w temp (* F)
Ent ch w temp (* F)
Ent hot w temp (* F)
Lvg hot w temp (* F)
Steam pressure (* psi)
8a Chilled water:
12 3
8a
Lvg ch w temp ( , ,
F)
Ent ch w temp (_ , ,
F) or
Ch w temp diff ( , ,
F)
gpm)
Lvg cond w temp ( , ,
F)
F) or
Cond w flow rate ( , ,
gpm)
Hot water: 8c
Lvg hot w temp ( F)
Ent hot w temp ( ,
F) or
Hot w temp diff ( ,
F)
Steam 8d
Steam pressure ( ,
psi)
COMMENTS
A43
: :
TEST WORK SHEET WS 3E-2 -- ABSORPTION CHILLER (FULL OR PART LOAD TEST)
continued
Page 3
Chiller no. Date
Check Fail &


than the tolerances

values not to exceed 1 F for temp,
5% for flow rate, and 0.2 psig for
steam pressure
10a Chilled water:

12 3
10a
Lvg ch w temp ( ,
F)
Ent ch w temp ( ,
F) or
Ch w temp diff ( F)
Ch w flow rate ( , KPm)
Full load only:
Ent ch w press ( , ,
psi)
Lvg ch w press ( ,
psi)
Lve cond w temp ( F)
Ent cond w temp ( ,
F) or
Cond w temp diff( ,
F)
Cond w flow rate( ,
F)
Full load only:
Ent cond w press ( ,
psi)
Lvg cond w press ( , ,
psi)
10c Electricity 10c
Wattmeter output ( ,
Watt)
lOd Hot water: lOd
Lvr Hot w temp ( F)
Ent hot w temp ( , F) or
Hot w temp diff ( F)
Hot w flow rate ( , £Pm)
Full load only:
Ent hot w press ( ,
psi)
Lve hot w press ( , ,
psi)
COMMENTS
A44
:
APPENDIX
TEST WORK SHEET WS 3E- 2 -- ABSORPTION CHILLER (-EULL OR PART LOAD TEST)
continued
Page 4
Chiller no. Date
Check Fail &

lOe Steam and condensate: lOe

Steam pressure ( ,
psig),
Steam temperature( ,
F) ,
Steam flow rate ( ,

lb/hr)
,
Condensate temp ( ,
F) ,
11 No unusual noise and vibration noticed 11

Lvg ch w temp ( F)
Ent ch w temp ( F) or
Ch w temp diff ( F)
Full load only:
Ent ch w press ( Psi)
Condenser water: 12b

Full load only:
Ent cond w press ( Psi)
Hot water: 12c
Lvg hot w temp ( F)
Ent hot w temp ( F) or
Hot w temp diff ( F)
Hot w flow rate ( gpm)
Full load only:
Ent hot w press ( Psi)
Lvg hot w press ( psi)
Steam and condensate: 12d
Steam pressure ( psig)
Steam temp ( F)
Steam flow rate ( lb/hr)
Condensate temp ( F)
COMMENTS
A45
: :
TEST WORK SHEET WS 3E-2 -- ABSORPTION CHILLER (FULL OR PART LOAD TEST)
continued
Page 5
Chiller no. Date
Check Fail &

13 Calculate capacity & performance: 13

13A Calculations: 13a
Capacity
Test capacity
(CAP) t -= (ch w temp diff) x (ch w flow rate) x 500 Btu/h

- cooling tons
24
cooling tons
24
Specified capacity (CAP) S = * Btu/h
Heat energy input:
Test energy input for hot water chiller

(Qin)t ” (hot w temp diff) x (hot w flow rate) x 500 Btu/h
= x x 500 -= Btu/h
Test energy input for steam chiller:

(Qin)t “ [(enthalpy of inlet steam) - (condensate temp - 32)]
x (steam flow rate) Btu/h
where enthalpy of steam is found from steam table by

knowing temp and pressure
Steam flow rate is in lb of steam/h
- (
- 32)] x Btu/h
Specified energy input (Q in ) s -= * Btu/h
COMMENTS
A46
: ) ) . .
APPENDIX
TEST WORK SHEET WS 3E-2 -- ABSORPTION CHILLER (-FULL OR PART LOAD TEST)
continued
Page 6
Chiller no. Date
Check Fail &

No. Steps Mark Pass Remarks No
COP of chiller:
(CAP) t
Test performance (COP) t =
(Qin)t
Specified performance (COP) s = *
Heat exchanger pressure drops (Full load test only):

(Pevap)t “ water pressure at evap inlet
- water
pressure at evap outlet
= - *= ft w.c.
Specified evaporator pressure drop (P eV ap)s “ * ft w.c.
Test condenser/absorber water pressure drop

(Pcond)t
= water pressure at cond inlet - water
pressure at cond outlet
= - = ft w.c.
Specified cond/absorb pressure drop (P con d) s = * ft w.c.
Test hot water pressure drop

(P hot )t = water pressure at generator inlet - water
pressure at generator outlet
«= - = ft w. c
Specified hot water pressure drop (Phot)s = * ft w.c.
(CAP t > ( CAP s
(Qin)t < (Qin)s

(COP t > (COP) s
(Pevap)t ^ (êvap)s
(^cond)t (^cond)s
(Phot)t < (^hot)s
COMMENTS
A47
:
3.14 TEST WORK SHEET WS 3F-1 — COOLING --TOWER

Page 1
Tower no. Date

Type: induced draft
forced draft
Number of cells

Check Fail &

1 Make sure water distribution is 1

balanced
2 Make sure water level in cold water 2
basin is correct
3 Check wind velocity, _mph, do not 3
10 proceed testing if wind velocity is
over 10 mph
4 Check air wet bulb temp, F, do not 4
proceed testing if wet bulb temp is
over or under 10 F of specified
(* F)
5 Disable condenser water temp control 5
6 Load refrigeration machine to full 6
load (see refrigeration machine test)
7 turn off makeup and bleed valves 7
8 Measure and adjust condenser water 8
flow rate to specified
(* gpm) gpm
9 Measure 3 hot water temp at 10 minute 9
intervals, variations between
measurements shall not exceed 0.5 F
F, F ,
F
Repeat step 9 if variations exceeds 10
limits
COMMENTS
A48
.
:
APPENDIX
TEST WORK SHEET WS 3F-1 -- COOLING TOWER continued

Page 2
Tower no Date
Check Fail &

11 Take 6 sets of test data at 10 min 11

intervals, tolerances between data
not to exceed: o.5 F for for water
temp, 2 F for air wet bulb temp, and
5% for water flow rate
Cold water temp (

12 , ,
3
F)
Hot water temp ( , ,
F) or
Water temp diff ( , ,
F)
Avg air WB temp ( , ,
F)#
Water flow rate ( , ,
gpm)
Wattmeter output( , ,
W)
4 5 6
Cold water temp ( , ,
F)
Hot water temp ( , ,
F) or
Water temp diff ( , ,
F)
Avg air WB temp ( , ,
F)#
Water flow rate (_ , ,
gpm)
Wattmeter output( , ,
W)
# Average of one or more
stations, see Manual
12 Calculate tower load for 6 data sets: 12
Test tower load = (water temp diff) x (water flow rate) x 500 Btu/h
Set 1 - X X 500 Btu/h
Set 2 - X X 500 = Btu/h
Set 3 - X X 500 = Btu/h
Set 4 - X X 500 = Btu/h
Set 5 = X X 500 = Btu/h
Set 6 = X X 500 = Btu/h
The difference of maximum and
minimum calculated tower load
not to exceed 5% of minimum.
(max - min) = - =
5% x min = 5% x
Repeat test if limit is exceeded.
COMMENTS
A49
:
TEST WORK SHEET WS 3F-1 -- COOLING TOWER continued

Page 3
Tower no. Date
Check Fail &


Cold water temp ( F)
Hot water temp ( F) or
Water temp diff ( F)
Air W B temp ( F)
Water flow rate (_ gpm)
14 Calculate and compare performance: 14

14a Test tower performance: 14a
Test tower range — (water temp diff) or

= (hot water temp) - (cold water temp)
F
Test cooling approach = (cold water temp) - (air WB temp)

F
14b Compare tower performance: 14b

The calculated test results of water
range and tower approach are compared
with manufacturer submitted curves
(see project specs)
COMMENTS
A50
:
APPENDIX
3.15 TEST WORK SHEET WS 3F-2 — REFRIGERANT CONDENSER (AIR

COOLED OR EVAPORATIVELY COOLED)
Page 1
Condenser no. Date

Type: Dry coil
Evaporative
Motor size: fan
pump_

Check Fail &

1 Check wind velocity (for evap condenser 1

located outdoor only) mph, do not
proceed if wind velocity is over 10 mph
2 check air wet bulb temp (for evap cond 2
only) F, do not proceed if it is
10 over or under 10 F from specified
(* F)
3 Check air temp F, do not proceed 3
if temp is below 80 F
4 Make sure water level is correct 4
(evap condenser only)
5 Test discharge pressure control (see 5
spec or submittals for details)
5a Temperature operated 5a
5b Pressure operated 5b
6 Disable discharge temp (or pressure) 6
control
7 Load refrigeration machine to full 7
load (see refrigeration machine test)
8 turn off makeup and bleed valves 8
9 Manipulate shut off valves to direct 9
refrigerant gas through flow measuring
device
Run system for at least 1 hour 10
COMMENTS
A51
:
TEST WORK SHEET WS 3F-2 -- REFRIGERANT CONDENSER S AIR COOLED OR EVAPORATIVELY

COOLED) continued Page 2
Condenser no. Date
Check Fail &


intervals, tolerances between data
not to exceed: 2 F for temp and 5%
for refrigerant flow rate
Ref inlet temp ( F)

ref inlet press ( F)
Ref outlet temp ( F)
ref outlet press( F)
Ref flow rate ( lb/hr)
Air DB temp # ( F) or
Air WB temp ## ( F)
Wattmeter ififif ( W)
4 5 6
Ref inlet temp ( ,
F)
ref inlet press ( ,
F),
Ref outlet temp ( F),
ref outlet press( ,

F),
Ref flow rate ( ,

Ib/hr)
,
Air DB temp if ( ,
F) or
,
Air WB temp if if ( F),
Wattmeter ififif ( ,
W),
if For air cooled condenser only

ifif For evaporative condenser only
ififif Fan elec power (air cooled)
Fan & pump elec power (evap cooled)
12 Check all 6 outlet conditions of 12
refrigerant: locate outlet temp and
press on refrig table or chart, if:
a) refrig is not subcooled and
b) air DB temp for air cooled or
air WB temp for evap cooled is
below specified,
the condenser is undersized
COMMENTS
A52
:
APPENDIX
TEST WORK SHEET WS 3F-2 -- REFRIGERANT CONDENSER (AIR COOLED OR EVAPORATIVELY

Condenser no. Date
Check Fail &

13 Calculate average data:

Ref inlet temp ( F)
ref inlet press ( F)
Ref outlet temp (____ F)
ref outlet press( F)
Ref flow rate (
lb/h)
Air DB temp # (
F) or
Air WB temp ## (
F)
Wattmeter ### ( W)
14 Calculate and compare performance: 14
14a Test capacity of air cooled condenser: 14a
14aa Enthalpy at inlet H in -- locate
,
14aa
inlet temp and press on refrig
table or chart Btu/lb
14ab Enthalpy at outlet, H out -- locate 14ab
outlet temp & press on refrig
14ac Test heat rejection rate at test conditions: 14ac
Qt - (refrig flow rate) x (H in -H out ) Btu/h
= x ( - ) = Btu/h
14ad Determin test condensing temp by locating refrig inlet 14ad
pressure on refrig table or chart, F
14ae Test heat rejection rate at specified conditions (in Btu/h): 14ae
(specified condensing temp) - (specified outdoor temp)

Qts
= x Qt
(test condensing temp) - (test outdoor temp)
x = Btu/h
14b Specified heat rejection rate Q s = * Btu/h 14b
COMMENTS
A53
:
TEST WORK SHEET WS 3F-1 -- REFRIGERANT CONDENSER-^ AIR COOLED OR EVAPORATIVELY

Condenser no. Date
Check Fail &

14c Test capacity of evaporative condenser: 14c

14ca Enthalpy at inlet Hin, -- locate 14ca
inlet temp and press on refrig
14cb Enthalpy at outlet, Hout -- locate 14cb
outlet temp & press on refrig
table or chart _Btu/lb
14cc Test heat rejection rate at test conditions: 14cc
Qt “ (refrig flow rate) x (H in -H out ) Btu/h
« x ( - ) = Btu/h
14cd Determin test condensing temp by locating refrig inlet
pressure on refrig table or chart, F 14cd
14d Manufacturer supplied capacity at test conditions (same air 14d
wet bulb temperature and refrigerant condensing temperature)
Q s *= * Btu/hr
15 Acceptance criteria: 15
15a Air cooled condenser: 15a
Qts > Qs
15b Evapratively cooled condenser: 15b
Qt > Q s
COMMENTS
A54
:
APPENDIX
4.1 INSPECTION CHECK LIST CL 4A-1 ~ BOILER

Page 1
Boiler no. Date


Boiler type
Heating medium: steam water
Energy source: oil gas elec
Pressure psig
NO. DESCRIPTION YES NO REMARKS NO.
For all boilers:

2 General appearances, no apparent damage 2
3 Verify boiler and burner model with submittals 3
5 Other access space adequate (headroom, 5
access doors, manholes, etc)
6 Heating plant clean, no fire hazards 6
7 Heating plant ventilation opening proper 7
9 Pipes cleaned before connecting to 9
boiler
11 Check valves and flow switches flow 11
direction correct
12 Pipes not supported on boiler (special 12
attention to safety valves)
13 Gas vent pipe extended to outside 13
17 Lubrication complete and proper 17
22 Insulation for induced draft fan applied 22
23 Surface paint complete, equipment labels 23
complete and legible
24 Refractory installed properly 24
COMMENTS
A55
:
INSPECTION CHECK LIST CL 4A-1 -- BOILER (continued)

Page 2
Boiler no. Date
26 Mercury switchs leveled correctly 26

27 Control air pressure correct (compressed 27
air control)
30 All electric connections tight 30
32 Test run motors for direction of rotation
32a fan 32a
32b pump 32b
32c air compressor 32c
32d other motors 32d
33 Oil filter clean 33
34 Water treatment maintained 34
35 Blowdown maintained 35
37 Test blowdown valves 37
38 Blowdown shows no leak 38
39 Setting of continuous blowdown proper 39
40 Automatic recording and control 40
instruments installed as specified
41 Proper calibration of instrumentation 41
42 Ranges, settings, and operations of 42
automatic recording and control
instrumantation proper
Boiler safety relief valve:

1 No damage noted 1
2 No leak noted 2
3 Pipe not supported on valve 3
4 Size of discharge pipe adequate 4
5 Valve removed during boiler boiloff 5
6 Valve setting correct 6
7 Field test of valve relief action 7
Note pressure when valve opened psi
COMMENTS
A56
:
APPENDIX

Page 3
Boiler no. Date
For oil and gas fired burners:

1 Inspect oil nozzles, igniters, 1
electrodes, etc.
2 Fuel -air ratio controller and linkage 2
3 Gas and oil line strainers clean, oil 3
pressure gage indication steady

4 Check all valves and switches for 4
correct positions
5 Gas pilot flame stable, when draft 5
fan is fully on
6 Pilot flame extinguish promptly, 6
when burner is on
7 Verify fuel safety valve interlocks 7
8 Verify temperature interlock switches
8a Low temperature 8a
8b High temperature 8b
9 Verify pressure interlock switches
9a Low pressure, oil supply line 9a
9b Low pressure, atomizing medium pipe 9b
9c Low pressure, gas supply pipe 9c
9d Low pressure, draft proof 9d
9e High pressure, gas supply pipe 9e
9f High pressure, steam 9f
9g Differential pressure, oil burner 9g
9h Other pressure 9h
10 Verify automatic gas safety shut- 10
off valve
11 Verify time delay action
11a Automatic safety shut-off valve 11a
lib Flame failure alarm lib
11c Control responses of flame failure 11c
lid Purger timer lid
12 Check action and time of automatic
fuel safety valve for:
12a Power failure (removing valve 12a
energy source)
12b Pressure interruption (closing 12b
manual valve)
13 Check low-fire lighting-off 13
14 Check pilot flame detection control 14
COMMENTS
A57
:

Page 4
Boiler no. Date
15 For sectional boilers with multi- 15

port burners and igniters, check
light-off action
16 Check all indicationg lights:
16a Flame failure 16a
16b Load demand 16b
16c fuel valve position 16c
16d Low water 16d
16e Draft fan 16e
16f Others 16f
Boiler capacity control:

1 Water circulation rate correct 1
2 Oil preheating system working properly 2
3 Oil temperature within limits 3
4 Boiler achieve warm conditions 4
5 Check fuel-air adjustment at low fire
5a Set firing rate at minimum 5a
5b Perform flue gas analysis 5b
5c Check CO and C0 2 amounts 5c
6 Check fuel-air adjustment at 25% fire
6a Set firing rate at 25% 6a
9 Check fuel-air adjustment at full fire
COMMENTS
APPENDIX

Page 5
Boiler no. Date
Boiler water level control and safety:

1 Water level control and low water 1
cutoff level
2 Wiring connection, switch installed 2
correctly
3 Test actual operation:
3a Set burner in low fire 3
3b Turn off makeup water valve 3b

3c Drain boiler water slowly 3c
3d observe water gauge glass, control 3d
action, and alarm
4 Gauge glass and gasket integraty 4
5 Gauge glass cleanliness 5
6 Operation of gauge glass isolation 6
and drain valves properly
7 Operation of try-cocks properly 7
Boiler breeching (for oil and gas boilers only):

1 Pitch of breeching 1
2 Cleanout door (location, size, 2
latching, etc.)
3 Expansion joint tightness 3
4 Tightness of breeching entering chimney 4
5 Test hole size and location 5
6 Insulation thickness and integraty 6
Oil preheating system (for No. 4, 5, and 6 oil only):

1 Check piping arrangement against 1
contract drawings
2 Test electric heater thermostat 2
2a Cutin temperature (* F) F 2a
2b Cutout temperature (* F) F 2b
3 Test hot water or steam heater 3
thermostat
3a Cutin temperature (* F) F 3a
3b Cutout temperature (* F) F 3b
4 Electric heater capacity 4
5 Hot water or steam heater capacity 5
6 Overall heater operation 6
7 Steam trap operation 7
COMMENTS:
A59
: :

Page
Boiler no. Date
Soot blower (Oil fired steam boilers only)

1
1 Burner at full firing )(-
2 Open drain valve

WK
3 Open steam valve to warm piping
s
4 Close drain valve
5 Steam pressure at recommended level
6 Perform soot blowing
\OOOvJO'Ult
7 Close steam valve

8 open drain valve
9 Evaluate soot blowing operation
COMMENTS
A60
: .
APPENDIX
4.2 INSPECTION CHECK LIST CL 4A-2 — FURNACE

Page 1
Furnace no. Date

Furnace type
Energy source: oil gas elec
NO. DESCRIPTION YES NO REMARKS NO

,
2
3 Verify furnace model with submittals 3
4 Access space adequate 4
5 Heating plant clean, no fire hazards 5
6 Heating plant ventilation opening proper 6
8 Pipes not supported on furnace 8
9 Flexible connection on duct installed 9
11 Alignment of motor and fan 11
17 Mercury switchs and mercury type 17
thermosta leveled correctly
21 Test run fan motor for direction of rotation 21
22 Air filter clean 22
23 Inspect oil nozzles, oil filter 23
24 Gas pilot flame stable, when fan is on 24
COMMENTS
A61
:
INSPECTION CHECK LIST CL 4A-2 -- FURNACE (continued)

Page 2
Furnace No .
Date
25 Test control operation

25a Raise room thermostat setting 10 F 25a
above room temperature
25b Observe burner operation 25b
25c Record bonnet tempertature when 25c
fan starts running F
25d Test limit switch and record 25d
temperature when burner stops F
25e Turn thermostat down 10 F or till 25e
burner stops
25f Record bonnet temperature when fan 25f
stops F
COMMENTS
A62
:
APPENDIX
4.3 TEST WORK SHEET WS 4B-1 -- INSTRUMENT CALIBRATION FOR BOILER

AND FURNACE Page 1
Date
Test agent
Commissioning team

1. This work sheet is used for calibrating sensing devices and
instruments used in recording performance tests. Calibration of
indicating devices for equipment operations are covered under
equipment test work sheets.
3. All instruments and sensing devices must be calibrated on bench or
in field with standard instruments. At least two points covering the
entire rangeofnormal operation should be calibrated. This work sheet
data in Block B.

Temperature
Humidity
Pressure
Power
Flow rate
Gas concentration
Others
B. Final calibration data (calibration points listed below may be changed


Temperature, F:
1 Water (for feed 32 200 1
water, condensate,
and hot water)
A63
: : .. ::
TEST WORK SHEET WS 8B-1 -- INSTRUMENT CALIBRATION' FOR BOILER AND FURNACE
continued Page 2
Date

Humidity:
2 Relative humidity, % 30#1 90//1 2
3 Dew point temp, F 35 75 3
4 Wet bulb temp, F 3 5# 2 75#2 4
6 Air 32 150 6
7 Flue 300 2000 7
Flow
8 Water and steam, gpm #3 #4 8
a
b.
c
9 Fuel (gas/oil) #5 9
Pressure
10 Gas, in. w.c. 0 20 10
11 Steam, psia 0 50 11
(for low pressure steam)
Flue gas concentration
12 C02 % ,
0 20 12
13 02, % 0 20 13
14 CO, % 0 3 14
Other devices:
a
b.
c
Notes
#1 Within a dry bulb range of 10 - 100 F
#2 Within a dry bulb range of 35 - 100 F
#3 25% below specified values
#4 25% above specified values
#5 Check against a calibrated flow instrument
Comments
A64
:
APPENDIX
4.4 TEST WORK SHEET WS 4B-2 -- GAS AND -OIL FIRED BOILER
Page 1
Boiler no. Date


Boiler type_
Energy source: oil gas
Pressure psig

2. and subscript "s" denote data required from specification,
Check Fail &

1 Test combustion efficiency at 25% 1

capacity:
la After boiler is warmed up set la
capacity to approx. 25% and on
manual control; adjust building
load to match boiler capacity
lb Capacity check by fuel input or lb

heat output:
(a) Fuel input:
elapsed time h
net gas meter reading ft 3
net oil meter reading gal
fuel input ft 3 /h or gph
(b) Heat output:
measured heat output Btu/h
* Btu/h x 0.25 -= Btu/h
COMMENTS
A65
:
TEST WORK SHEET WS 4B-2 -- GAS AND OIL FIRED BOILER continued
Page 2
Boiler no .
Date
Check Fail &

lc Prove of steady state: lc
Flue temp
12 3
F
,
For hot water boiler:

ent water temp , ,
F
lvg water temp , ,
F
For steam boiler:
steam pressure ,
psig
steam temp F
Id Check steam condition (steam Id

boiler only for all 3 sets of
steam readings. Steam must be
at least saturated.
le Flue gas CO level_ % by vol le

Specified max CO level * % by vol
If measured level is higher than
specified, stop test
If Take data at 15 min intervals: If
C0 2 or 0 2 level
12 3
%
,
flue gas temp , ,

F
comb air temp , ,
F
For H W boiler:
ent water temp , ,
F
lvg water temp F or
water temp diff ,
F
For steam boiler:
steam pressure ,
psig
steam temp , ,
F
feed water temp ,
F
COMMENTS
A66
:
APPENDIX
Page 3
Boiler no. Date
Check Fail &

lg Average test data: !g

C0 2 or 0 2 level ___ %
flue gas temp F
comb air temp F
For H W boiler:
ent water temp F
lvg water temp F or
water temp diff F
For steam boiler:
steam pressure psig
steam temp F
feed water temp F

capacity
2a Set capacity to approx. 50% and on 2a
2b Capacity check by fuel input or 2b

heat output:
(a) Fuel input:
elapsed time h
fuel input ft 3 /h or gph
* ft 3 /h or gph x 0.5 =
(b) Heat output:
* Btu/h x 0.5 = Btu/h
2c Prove of steady state: 2c

1 2 3
Flue temp ,
F
ent water temp ,
F
lvg water temp ,
F
For steam boiler:
: .
Page 4
Boiler no. Date
Check Fail &

2d Check steam condition (steam 2d

at least saturated.
2e Flue gas CO level % by vol 2e

2f Take data at 15 min intervals: 2f
C0 2 or 0 2 level
12 3
%
,
flue gas temp ,

F
comb air temp , ,
F
For H W boiler:
ent water temp ,
F
lvg water temp ,
F or
water temp diff , ,
F
For steam boiler:
steam pressure ,
psig
steam temp , ,
F
feed water temp ,
F
2g Average test data: 2g

C0 2 or 0 2 level %
For H W boiler:
water temp diff F

For steam boiler:
steam pressure psig
steam temp F
feed water temp _____ F
COMMENTS
A68
:
APPENDIX
TEST WORK SHEET WS 4B-2 -- GAS AND OIL FIRED BOTLER continued
Page 5
Boiler no. Date
Check Fail &

capacity
3a Set capacity to approx. 75% and on 3a
3b Capacity check by fuel input or 3b

heat input:
(a) Fuel input:
elapsed time h
* ft 3 /h or gph x 0.75 = Btu/h
(b) Heat output:
* Btu/h x 0.75 = __ Btu/h
3c Prove of steady state: 3c
Flue temp
12 3

ent water temp , ,
F
lvg water temp , ,
F
For steam boiler:
steam pressure , ,
psig
steam temp , ,
F
3d Check steam condition (steam 3d

at least saturated.
3e Flue gas CO level % by vol 3e

COMMENTS :
A69
: .
Page 6
Boiler no. __ Date ____

Check Fail &
C0 2 or 0 2 level
12 ,
3
%
,
flue gas temp

comb air temp F
For H W boiler:
ent water temp F
lvg water temp F or
water temp diff F
For steam boiler:
steam pressure psig
steam temp F
feed water temp F

C0 2 or 0 2 level %
flue gas temp F
comb air temp F
For H W boiler:
ent water temp F
lvg water temp F or
water temp diff F
For steam boiler:
steam pressure _ Psig
steam temp F
feed water temp F
4 Test boiler capacity and efficiency 4

at 100% capacity:
4a Set capacity to full and on 4a

COMMENTS
A70
: .
APPENDIX
Page 7
Boiler no .
Date
Check Fail &

4b Prove of steady state: 4b
Flue temp
12 3
F
,

ent water temp , ,
F
lvg water temp , ,
F
For steam boiler:
steam pressure , ,
psig
steam temp ,
F
4c Check steam condition (steam 4c

at least saturated.
4d Flue gas CO level % by vol 4d

Specified max CO level * 1 by vol
4e Take fuel data for test period: 4e

elapsed time h
For gas fired boiler:
barometric pressure in. Hg
gas pressure in. wc
gas temp F or
For oil fired boiler:
oil pressure psig
oil temp F_
Gas or oil flow rate:
meter reading
ft 3 /h or gph
time
COMMENTS
A71
:
Page 8
Boiler no. Date
Check Fail &

comb air temp

12 ,
3
F
,
For H W boiler:
ent water temp , ,
F
lvg water temp ,
F or
water temp diff , ,
F
water flow rate , ,
gpm
location of flow measurement:
(check one) ent lvg ,
For steam boiler:

steam pressure , ,
psig
steam temp , ,
F
feed water temp , ,
F

comb air temp F
For H W boiler:
ent water temp F
lvg water temp F or
water temp diff F
water flow rate gpm
For steam boiler:
steam pressure _____ psig
steam temp F
feed water temp F

5a Capacity: use 100% capacity test data 5a
(a) Hot water boiler:
If test data is in vol flow rate (Q gpm) convert to mass flow
,
rate (M lb/h) by SE-13

Enthalpy of leaving water (H out ) Btu/lb
Enthalpy of entering water (H in ) Btu/lb
Test capacity (CAP) t = M x (H out - H in ) Btu/h

= x ( - )
- Btu/h
COMMENTS
A72
:
APPENDIX
TEST WORK SHEET WS 4B-2 -- GAS AND OIL FIRED BO-ILER continued
Page 9
Boiler no .
Date
Check Fail &

(b) Steam boiler:

If test data is in vol flow rate (Q) convert to mass flow
,
rate (M Ib/h) by using steam table

Enthalpy of steam (H s ) Btu/lb
Enthalpy of feed water (H^) Btu/lb
Test capacity (CAP) t «= M x (H s - H„) Btu/h

= x ( - ) - Btu/h
5b Combustion efficiency at part load, use charts 5b

(see EXHIBIT 4-B)
efficiency at 25% cap (25% eff) = %

5c Thermal efficiency at full load: 5c

(a) Heat input for gas fired boiler:
Convert measured gas flow rate to that of standard
conditions (equation in 7.2.1, EXHIBIT 4-B):
Flow rate at std conditions Q s = ft 3 /h
3
Heating value of gas (HHV) Btu/ft
Calculate heat input of boiler:
(q)m = (Qs) X (HHV) = X = Btu/h
(b) Heat input for oil fired boiler:

Calculate oil flow rate at 60 F (equation in 7.2.2, Exhibit 4-B):
Flow rate at 60 F = gph
Heating value of oil (HHV) Btu/gal
Calculate heat input of boiler:
(q)m = (Qs) x (HHV) = x_ = Btu/h
COMMENTS
A73
:
Page 10
Boiler no. Date
Check Fail &

(c) Output of boiler:

(q)out * (CAP) t - Btu/h (from 5a)
(d) Boiler thermal efficiency:
(q)out
eff - x 100 - x 100 - %
(q)in
6. Acceptance criteria: 6
Capacity: (CAP) t > (CAP) S
Combustion efficiency at part load:
at 25% capacity not less than * %
Thermal efficiency at full load no less than * %
COMMENTS
A74
: ,
APPENDIX
4.5 TEST WORK SHEET WS 4B-3 — ELECTRIC- BOILER

Page 1
Boiler no. Date


Boiler type
Pressure psig

Check Fail &

1 Test boiler capacity and efficiency 1

at 100% capacity:
la Set capacity to full and on la
lb Check electric voltage: lb
phases 1-2 V
phases 1-3 V
phases 2-3 V
lc Prove of steady state: lc
ent water temp

12 3
HW boiler
, ,
lvg water temp , ,

HW boiler
steam pressure , ,
St boiler
steam temp , ,
F
Id Check steam condition (ST boiler Id
only) for all 3 sets of steam
readings. Steam must be at least
saturated.
COMMENTS
A75
: t
TEST WORK SHEET WS 4B-3 -- ELECTRIC BOILER continued

Page 2
Boiler no._ Date
Check Fail &

le Take data for test period: le

time at start of test h min sec
watthour reading at beginning Wh
time at end of test h min sec
watthour reading at end Wh
If Take data at 15 min intervals: If
room air temp

12 ,
3
F
,
For H W boiler:
ent water temp , ,
F
lvg water temp ,
F or
water temp diff ,
F
water flow rate , ,
gpm
location of flow measurement:
(check one) ent lvg ,
For steam boiler:

steam pressure , ,
psig
steam temp , ,
F
feed water temp , ,
F
steam flow rate , ,
ft 3 /min
lg Average test data: lg

room air temp F
For H W boiler:
ent water temp F
lvg water temp F or
water temp diff F
water flow rate gpm
For steam boiler:
steam pressure psig
steam temp F
feed water temp F
3
steam flow rate f /min
COMMENTS
:
APPENDIX

Page 3
Boiler no. Date
Check Fail &


2a Capacity: 2
(a) Hot water boiler:
If test data is in vol flow rate (Q gpm) convert to ,
mass flow rate (M lb/h) by SE-13

Enthalpy of leaving water (H out ) Btu/lb
Enthalpy of entering water (H in ) Btu/lb
Test capacity (CAP) t = M x (H out - H in ) Btu/h

= x ( - ) = Btu/h
(b) Steam boiler:

If test data is in vol flow rate (Q) convert to mass flow,
rate (M lb/h) by using steam table

Enthalpy of steam (H s ) Btu/lb
Enthalpy of feed water (H^) Btu/lb
Test capacity (CAP) t = M x (H s - H„) Btu/h

= x ( )
= Btu/h
2b Thermal efficiency at full load: 2b

(a) Heat input rate to boiler (see Id):
(end kwh - start kwh)

(q)in
(end time - start time)
(
kwh) -
(
kwh)
= x 3413 = Btu/h
( h) - ( h)
COMMENTS
A77
: q .

Page 4
Boiler no. Date__
Check Fail &

(b) Output of boiler:

(q)out “ ( CAp )t - Btu/h (from 2a)
(c) Boiler thermal efficiency:
( ) out _
eff - x 100 -- x 100 - ___ %
<q)in
3. Acceptance criteria: 3
Thermal efficiency at full load no less than * %
COMMENTS
A78
APPENDIX
4.6 TEST WORK SHEET WS 4C-1 — GAS AND— OIL FIRED AIR FURNACE
Page 1
Furnace no. Date


Furnace type_
Energy source: oil gas

Check Fail &

1 Turn thermostat up 10 F to start 1

furnace combustion.
2 Test capacity and combustion efficiency: 2
2a Run furnace for at least 15 minutes. 2a
2b Flue gas CO level % by vol 2b
2c Take 3 sets of data at 15 min 2c
intervals
C0 2 or 0 2 level
12 %
3
, ,
flue gas temp ,

F ,
comb air temp ,

F ,
return air temp ,

F //,
supply air temp ,

F # ,
air flow rate ,

CFM #
,
# Traverse of duct cross section is

required for both temperature and
air flow. Prepare data recording
sheet for traverse data. See
EXHIBIT 2-C for flow traverse
procedures
2d Take data: 2d
return or supply air humidity
1 or F dew point
barometric pressure in. water
COMMENTS
A79
:
TEST WORK SHEET WS 4C-1 -- GAS AND OIL FIRED AIR-FURNACE continued
Page 2
Furnace no. Date
Check Fail &

2e Average test data: 2e

C0 2 or 0 2 level _____ %
flue gas temp F
comb air temp F
return air temp F
supply air temp F
air flow rate CFM

3a Capacity: 3a
See EXHIBIT 2-B for calculation of air properties.
Calculate return air enthalpy (Hout) _____ Btu/lb
Calculate supply air enthalpy (Hout) Btu/lb
Calculate specific volume of air (v) using average of supply
,
and return air conditions:

average air temp F
average air humidity _____ % or ___ F dew point
average air density (v) lb/ft 3
Measured air flow rate (Q) from 2e, ,
CFM
Calculate furnace capacity:
Q
Test capacity (CAP) t x (H out - H in ) Btu/h
v
x (____ - ) - _____ Btu/h
3b Combustion efficiency at full load, use equations or 3b

charts (see Chapter 4)
combustion efficiency = __ %
Combustion efficiency at full
load not less than * %
COMMENTS
A80
APPENDIX
4.7 TEST WORK SHEET WS 4C-2 — ELECTRIC AIR FURNACE

Page 1
Furnace no. Date

Serial no._ Commissioning team

Furnace type
N o e s for using form:

t:
Check Fail &

1 Check electric voltage: 1

phases 1-2 V
phases 2-3 V
phases 2-3 V
2 Turn thermostat up 10 F to start 2
furnace combustion.
3 Test capacity: 3
3a Run furnace for at least 15 minutes. 3a
3b Take 3 sets of data at 15 min 3b
intervals
return air temp

12 3
F #
, ,
supply air temp , ,

F #
air flow rate , ,
CFM #
# Traverse of duct cross section is
required for both temperature and
air flow. Prepare data recording
sheet for traverse data. See
EXHIBIT 2-C for flow traverse
procedures
3c Take other data: 3c
return or supply air humidity
% or F dew point
barometric pressure in. water
COMMENTS
:
TEST WORK SHEET WS 4C-2 -- ELECTRIC AIR FURNACE continued

Page 2
Furnace no. Date
Check Fail &

3d Average test data: 3d

return air temp F
supply air temp F
air flow rate CFM

4a Capacity: 4a
See Chapter 2 for calculation of air properties.
Calculate return air enthalpy (H out ) Btu/lb
Calculate supply air enthalpy (H out ) Btu/lb
Calculate specific volume of air (v) using average of
,
supply and return air conditions:

average air temp F
average air humidity ___ % or F dew point
average air density (v) lb/ft'
Measured air flow rate (Q) from 2f, ,
CFM
Calculate furnace capacity:
Test capacity (CAP) t = --- x (H out - H in ) Btu/h

v
x ( ) - Btu/h
4b Combustion efficiency at full load, use equations 4b

or charts (see Chapter 4)
combustion efficiency = 1
Combustion efficiency at full
load not less than * %
COMMENTS
A82
APPENDIX
5.1 INSPECTION CHECK LIST WS 5A-1 — AIR HANDLING UNIT

Page 1
ACU no. Date

Serial no. Commissioning team _

Type
General
2 General appearances,
no apparent damage 2
3 Verify unit model with submittals 3
5 Air filter replacement space adequate 5
access doors, etc)
7 Equipement room cleaned, no fire hazards 7
8 Equipment room ventilation opening proper 8
9 Ventilation opening automatic damper 9
12 Check valves and flow switches flow 12
direction correct
13 Pipes supported properly 13
21 Electric wiring installation proper 21
22 Elec motors & components grounded properly 22
25 Test run motors for direction of rotation 25
COMMENTS
A83
. :
INSPECTION CHECK LIST WS 5A-1 -- AIR HANDLING UNTT (continued)

Page 2
ACU no Date
28 Control air pressure correct (compressed 28

air control)
29 No excessive air leakage of unit 29
31 Automatic control instruments 31
installed as specified
Fan:
Housing access doors and latchs tight
1 1
Assembly bolts tight (field assembled fan)
2 2
103 Grease or oil tubes for bearins proper 3

A No need removing belt guard for oiling 4
or speed check
5 Fan running steadily 5
6 Fans with inlet vanes or outlet dampers:
6a Damper linkage no excessive play 6a
6b Damper closes tight 6b
6c Direction of inlet damper blade proper 6c
6d Inlet dampers for double inlet fan proper 6d
7 Protective hood over motor and belt for 7
outdoor installation
8 Inlet and outlet wire protection for fan 8
without duct connection
9 Flexible connections between fan and ducts 9
Curb watertightness (power roof vent) 10
COMMENTS
A84
APPENDIX
INSPECTION CHECK LIST WS 5A-1 -- AIR HANDLING UNIT (continued)

Page 3
Coils
1 No damage to heat transfer fins 1
la Preheat coil la
lb Main heating coil
lc Precooling coil lc
Id Main cooling coil Id
le Reheat coil le
2 Coil tubes pitch correctly 2
2a Preheat coil 2a
2b Main heating coil 2b
2c Precooling coil 2c
2d Main cooling coil 2d
2e Reheat coil 2e
3 No air bypass between coil and casing 3
3a Preheat coil 3a
3b Main heating coil 3b
3c Precooling coil 3c
3d Main cooling coil 3d
3e Reheat coil 3e
4 Cooilin coil drain pans and pipes 4
5 Coil pipe fittings and accessories 5
5a Shut-off valves 5a
5b Strainers 5b
5c Air vents 5c
5d Thermometer wells 5d
5e Balancing devices 5e
5f Drain 5f
5g Others 5g
6 Flow measuring device 6
6a Upstream pipe length or flow straightener 6a
6b Downstream pipe length 6b
6c Meter connection and valves complete 6c
6d Tag with flow rate information 6d
7 Condensate pipe at steam trap - check that 7
steam trap is not passing steam when
control valve is open
(for low pressure steam only)
COMMENTS :
A85
: .

Page 4
AHU no. Date
Air filters:
1 Filter frame anchored to casing securely 1
2 No air leakage around filter frame 2
3 No air leakage between filter bank 3
and unit casing
4 New filter media 4
5 Filter gage pressure sensing tip proper 5
6 Inclined manometer gage installation 6
7 Check auto renewable filter advancing 7
mechanism
7a Motor 7a
7b Drivingtrain 7b
7c Timer 7c
7d Pressure sensing 7d
7e Overriding operation 7e
8 Filter replacement spece adequate 8
9 Spare filters 9
Air dampers:
1 Blade arrangement: parallel 1
opposed
2 Blade edge sealing 2
3 Bearings as specified 3
4 Actuator linkage and blade movement 4
5 Access door for dampers in duct 5
Air louvers:
1 Material 1
2 Construction 2
3 Dimensions 3
4 Screen 4
COMMENTS
A86
APPENDIX

Page 5
AHU no. Date
Casings
1 Rigidity 1
2 Integraty 2
3 Access doors: 3
3a Size 3a
3b Gasket 3b
3c latches 3c
4 Flexible connections between unit 4
and ducts
5 Outdoor unit roof curb flashing 5
6 Enclosure for outdoor unit 6
Thermal insulation:
1 No damages and omissions 1
2 Material 2
3 Thickness 3
4 Method of application 4
5 Vapor barrier material and sealing 5
6 Surface finishing 6
COMMENTS
A87
: j

Page 6
AHU no . Date
Automatic controls:
1 Give general check on control installations 1
against contract documemts and submittals,
control diagrams complete, framed and mounted
2 Observe general operation. Any obvious 2
malfunction, incorrect calibrations, or
incorrct settings and ranges? Hunting observed?
3 Are mercury switches leveled correctly? 3
4 Check valves for correct closing 4
5 Valves and linkages installed securely 5
6 Valve linkages travel freely 6
7 Check dampers for correct closing 7
8 Dampers and linkages installed securely 8
9 Damper linkages travel freely 9
10 Safety features (coil freeze trotection, 10
etc.) installed correctly
11 Interlocking installed correctly 11
12 For pneumatic systems: 12
12a Compressor intake filter clean 12a
12b Compressor discharge filter clean 12b
12c Compressor motor alignment 12c
12d Compressor belt tightness 12d
12e Belt protective shield 12e
12f Compressor oil level 12f
12g Compressor oil filter clean 12g
12h Air tank drain 12h
12i Air pressure at air tank 12i
12 j Air pressure after pressure 12
reducing valves
12k Air tubing connections tight 12k
121 Air pressure gages
13 For electrcal and electronic systems: 13
13a Wire connections tight 13a
13b No broken wires 13b
13c No rust on wire terminals 13c
13d Correct voltage of power supply 13d
13e Signal wires shielded correctly 13e
14 Control panels: wires and tubes labeled,
settings marked, notes attached
COMMENTS
A88
APPENDIX
5.2 TEST WORK SHEET WS 5B-1 — INSTRUMENT CALIBRATION FOR AIR

HANDLING SYSTEMS Page 1
Date
Test agent
Commissioning team

1. This work sheet is used for calibrating sensing devices and instruments
used in recording performance tests. Calibration of indicating devices
for equipment operations are covered under equipment test work sheets.
field with standard instruments. At least two points covering the
entire rangeofnormal operation should be calibrated. This work sheet
data in Block B.
A. Standard instruments data (copy from standard instrument records)

Temperature
Humidity
Pressure
Power
Others
B. Final calibration data (set- temperature listed below may be changed

Instrument Approx. Std Final Approx Std

. Final
No. Device Point Reading Reading Point Reading Reading No
Temperature, F:
1 Water (for chilled, 32 200 1
condenser, steam
condensate, and hot)
3 Air 32 150 3
A89
: .. ::
TEST WORK SHEET WS 5B-1 -- INSTRUMENT CALIBRATION- FOR AIR HANDLING SYSTEMS
continued Page 2
Date

9
Humidity:
A Relative humidity, % 30//1 90#1 4
see Note #1
6 Wet bulb temp, F 35#2 75#2 6
see Note #2
Flow:
a.
b.
c
8 Air velocity, fpm, 0 1000 8

Also see #5
Pressure
Water, ft w.c. or psi 0 //6 9
10 Air, in. w.c. 0 #7 10
Other devices:
a
b.
c
Notes
n Within a dry bulb temperature range of 10 - 100 F
#2 Within a dry bulb temperature range of 35 - 100 F
y/4 25% above specified values
#5 This is for velocity type instrumsnts, see pressure calibration
for pressure sensing devices (pitot)
#6 Expected highest pressure
#7 Expected highest pressure or 5 in. w.c. whicherever is higher
Comments
A90
APPENDIX
5.3 TEST WORK SHEET WS 5B-2 — AIR HANDLING SYSTEM (COMPONENT

TEST) FAN
, Page 1
AH (or fan) no. Date

Serial no._ Commissioning team

Type
Fan type

Check Fail &

Supply air fan and return air fan

for constant air volume system:
1 Set and lock

outside air damper 1
at minimum
position
2 Set and lock
return air damper 2
3 Set and lock
relief air damper 3
4 Measure barometric pressure •Hg 4
5 Measure electric service voltage: 5

5a Supply fan motor: 5a
Phases 1-2 V
Phases 2-3 V
Phases 3-1 V
5b Return fan motor: 5b

Phases 1-2 V
Phases 2-3 V
Phases 3-1 V
COMMENTS
A91
: : . .
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), FAN continued
Page 2
Check Fail &

6 Measure supply air fan performance:
6a Air flow rate, use Test Work Sheet 6a

WS 2C-1 or 2C-2 cfm (* cfm)
6b Total p at fan inlet in. w. c 6b
6c Static p at fan inlet in.w.c. 6c
6d Total p at fan outlet in.w.c. 6d
6e Static p at fan outlet in.w.c. 6e
6f Velocity p at fan inlet in.w.c. 6f
6g Velocity p at fan outlet in.w.c. 6g
6h Fan speed rpm 6h
6i Motor current and name plate FL current: 6i

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
7 Check 10% of supply air outlets 7
7a Room ,
measured cfm (* cfm) 7a
Room ,
measured cfm (* cfm)
Room ,
Room ,
Room ,
7b Calculate error 7b
(1 - measured/specified supply) x 100%
Room ,
Error = %
Room ,
Error = %
Room ,
Error = %
Room ,
Error = %
Room ,
Error *= %
7c If 10% of 7b is outside +/- 10 %, 7c

check another 10% of supply outlets:
COMMENTS
A92
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ^COMPONENT TEST), FAN continued
Page 3
Check Fail &

7d Room measured
,
cfm (* cfm) 7d
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
7e Calculate error 7e
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%
8 If 10% of the outlets measured in 7b & 7e 8

are outside +/- 15%, rebalance system.
9 Total air flow rate of measured outlets cfm (7a & 7d) 9
10 Total air flow rate of specified cfm (7a & 7d) 10
11 Calculate error 11
(1 - measured/specified supply) x 100% = %
12 If error in 11 is outside +/- 10%, rebalance system. 12
13 Measure return air fan performance: 13

13b Total p at fan inlet in w c . . 13b
13c Static p at fan inlet in. w. c 13c
13d Total p at fan outlet in w c . . 13d
13e Static p at fan outlet in.w. c 13e
13f Velocity p at fan inlet in w c . . 13f
13g Velocity p at fan outlet in. w. c 13g
13h Fan speed rpm 13h
COMMENTS
A93
:
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ( 6OMP0NENT TEST), FAN continued
Page 4
AH (or fan) no._ Date
Check Fail &


Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
14 Set outside air damper to 100% OA 14
15 Set return air damper 15
16 Set relief air damper 16
17 Measure supply fan motor current: 17

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
18 Measure return fan motor current: 18

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
19 Restore damper controls 19
20 Check 10% of return air outlets 20
20a Room ,
Room ,
Room ,
Room ,
Room ,

Room ,
Error = %
Room ,
Error = %
Room ,
Error = %
Room ,
Error *= %
Room ,
Error = %
COMMENTS
A94
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM -(.COMPONENT TEST), FAN continued
Page 5
Check Fail &

20c If 10% of 7b is outside +/- 10%, 20c

20d Room measured
,
cfm (* cfm) 20d
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
Room measured
,
cfm (* cfm)
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%
Room Error =
,
%

COMMENTS
A95
:
Page 6
AH (or fan) no .
Date
Check Fail &


for variable air volume system:
1 Set and lock outside air damper 1

at 100% OA position
2 Set and lock return air damper 2
3 Set and lock relief air damper 3
4 Measure barometric pressure in.Hg 4

Phases 1-2 V
Phases 2-3 V
Phases 3-1 V

Phases 1-2 V
Phases 2-3 V
Phases 3-1 V
6 Select 10% of VAV boxes:

6a Lower rm. thermostats 5 F to measure max. flow, note 6a
operation of reheat coil/recirculating fan:
Box if measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Raise rm. thermostats 10 F to measure min. flow 6b
operation of reheat co il/recirculating fan:
Box # measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
Box if measured
,
cfm (* cfm)
COMMENTS
A96
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM -(-COMPONENT TEST), FAN continued
Page 7
Check Fail &

6c Calculate error: 6c
Box # ,
Error = % (max) Error = % (min)
Box # ,
Box # ,
Error - % (max) Error = % (min)
Box # ,
Error *= % (max) Error - % (min)
Box # ,
7 If 10% of VAV boxes measured are

outside +/- 10%, check another 10% of boxes:
7a Lower rm. thermostats 5 F to measure max. flow, note
Box # measured
,
cfm (* cfm) 7a
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Raise rm. thermostats 10 F to measure min. flow,
Box # measured
,
cfm (* cfm) 7b
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Calculate error: 7c
Box # Error =
, % ( max ) Error = %(min)
Box # Error =
, % (max) Error = %(min)
Box # Error =
Box # Error =
Box # Error =
, % (max) Error =
;
%(min)
COMMENTS
:
Page 8
AH (or fan) no._ Date
Check Fail &

8 If 10% of the VAV boxes measured in 6 & 7 are 8

outside +/- 15%, rebalance system.
9 Total air flow rate of measured boxes cfm (max) 9
10 Total air flow rate of specified cfm (max) 10
11 Total air flow rate of measured boxes_ cfm (min) 11
12 Total air flow rate of specified cfm (min) 12
13 Calculate error: 13
(1 - measured/specified supply) x 100% - % (max)
(1 - measured/specified supply) x 100% = % (min)
15 Measure and record duct static pressure at fan 15

static pressure sensor locations:
Sensor //I measured "w.c. (shown on control dwg _"w.c.)
Sensor #2 measured "w.c. (shown on control dwg "w.c.)
16 Measure duct static pressure at branch ducts 16

before last VAV boxes:
Branch 1 measured "w c
.
Branch 2 measured "w.c

17 Specified minimum static pressure * "w.c. 17
18 Any branch must be: 18

* w.c. < measured press < measured press + 0.2"w.c.
COMMENTS
A98
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ^COMPONENT TEST), FAN continued
Page 9
Check Fail &

No Steps mark Pass Remarks No.
19 Record supply air fan performance: 19

19a Air flow rate, see Test Work Sheet 19a
19b Total p at fan inlet in.w.c. 19b

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)

20b Total p at fan inlet_ in.w.c. 20b
20d Total p at fan outlet_ in.w.c. 20d

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
COMMENTS
A99
:
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), HEATING COIL
continued Page 10
AH no .
Date
Preheat coil no. Inspection agent
Reheat coil no. Commissioning team

Heating medium: Steam
(Check
3. one) Water

All air temperature for coils must be measured at 1 ft sq face area
9 Check Fail &

Heating coil:
1 Measure coil air flow rate, see 1
Test Work Sheet WS 2C-2 cfm
2 Measure entering air temp 2
apply false load if needed
(* F)
average temp F
3 Measure & adjust ent w temp to within 3
1 F of specified (water coil)
(* F) F
4 Measure & adjust steam temp & 4
pressure (steam coil) to
within 1 psi of specified
(* psi) psi _____ F
Is steam saturated?
5 Measure and adjust water or steam 5
flow rate to within 3% of specified
6 Disable control of test coil 6
7 Run unit for at least 10 minutes 7
8 Test for steady state at 5 minute 8
intervals: (max diff 2 F)
average lvg air temp:
Measure barometric pressure in.Hg 9

COMMENTS
A100
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ^COMPONENT TEST), HEATING COIL
continued Page 11
AH no. Date
Preheat coil no.
Reheat coil no.
Check Fail &

10 Measure and record 3 sets of test data 10

at 5 min intervals:
Ent air temp

12 , ,
3
F
Lvg air temp , ,
F
Ent w pressure , ,
ft w.c.
Lvg w pressure , ,
ft w.c.
Air friction , ,
in. w.c.
11 Calculate coil capacity: 11

11a Saturated water vapor, P sw : 11a
P sw £>(15.4638 - 7284/ (Td+392 )

* «= e [ ]
4638 - 7284/ +392)]

e ( 15 [
in. Hg
.
(
(Psw) ent
lib Vapor pressure, Pw : lib
P w = RH x P sw
(Pw)ent = 0.5 x (P sw ) ent = 0.5 x = in.Hg
COMMENTS
:
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), HEATING COIL
continued Page 12
AH no. Date
Preheat coil no.
Reheat coil no.
Check Fail &

11c Humidity ratio, W: 11c
W 0.622 x
(W) ent - 0.622 x - lb vapor/lb dry air
( W) en t - (W)ent - lb vapor/lb dry air
lid Enthalpy, H: lid
H = 0.24 x Td + W (1061 + 0.444 x Td)
(H) ent - 0.24 x + (1061 + 0.444 x )

- Btu/lb
(H) lvg - 0.24 x + (1061 + 0.444 x )

- Btu/lb
lie Specific volume of air, v: lie

Note: Measurement location of Td and flow rate must be consistent.
0.754 x (Td + 460)

v - - - (1 + 1.6078 x W)
Pb
0.754 x (_ + 460)
- ---- -
(1 + 1.6078 x W) - cu ft/lb
Pb
COMMENTS
A102
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ^(COMPONENT TEST), HEATING COIL
continued Page 13
AH no. Date
Preheat coil no.
Reheat coil no.
Check Fail &

Ilf Mass flow rate of air, M: Ilf
cfm cfm
M «= lb/min
v
llg Coil heating capacity, C: llg
C = 60 M x [
( H ) lvg - (H) ent ]
-= 60 x x ( - ) = Btu/h
12 Repeat calculations for all 3 sets of data,

Averaged coil heating capacity: 12
( + + )/3 = Btu/h
13 Calculate coil water pressure drop, P: 13
P = ( P) ent - (P)lvg = - = ft w c - -
C > 0.95 x * capacity > 0.95 x >

P < 1 x * press drop < 1.1 x
.
<
AF < 1.1 x * air friction < 1.1 x <
COMMENTS
A103
: .
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), COOLING COIL
continued Page 14
AH no. Date
Precooling coil no. Inspection agent
Cooling coil no Commissioning team

3. All air temperature for coils must be measured at 1 ft sq face area
and averaged.
Check Fail &

Water coil:
2 Measure entering air temp & 2
humidity; apply false load if needed
(* F, * % RH)
average temp F, % RH
1 F of specified (water coil)
(*_ F) F
4 Measure and adjust water flow rate 4
to within 3% of specified
5 Disable control of test coil 5
Average lvg air temp:
Leaving air humidity:
COMMENTS
A104
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM -(-COMPONENT TEST), COOLING COIL
continued Page 15
AH no. Date
Precooling coil no.
Cooling coil no.
Check Fail &


at 10 min intervals:
air temp
Ent
12
F , ,
3
Lvg
air temp F , ,
air humidity
Ent % , ,
air humidity
Lvg % , ,
w pressure
Ent ft w.c. (coil or condenser)
, ,
w pressure
Lvg ft w.c. (coil or condenser)
, ,
Air friction in. w.c. , ,
10 Average test data: 10

Ent w pressure, (p)ent ft w.c. (coil or condenser)
Lvg w pressure, (P)lvg ft w.c. (coil or condenser)
Air friction, AF in. w.c.
11 Calculate coil capacity: 11
11a Saturated water vapor of air, P sw : 11a
15. 4638 - 7284/ (Td-392 )

r sw - e
P [
(Psw)ent - e<
15 -“ 38 - V™' + 392 ” = in. Hg
(Pswhvg = e
(15 * 638 - t 7284/ + 392 » = in. Hg
COMMENTS
A105
:
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), COOLING COIL
continued Page 16
AH no. Date
Precooling coil no.
Cooling coil no. _____
Check Fail &

lib Vapor pressure, P w : lib
P w - RH x P sw
( Pw) ent - 0.5 x (Psw)ent “ 0.5 X in.Hg
0.5 x (P R w)iv f - 0.5 x - in.Hg

( Pw) ent -
Pw
W - 0.622 x
Pb ‘ Pw
(W) ent = 0.622 x lb vapor/lb dry air
<W) lvg = 0.622 x lb vapor/lb dry air
lid Enthalpy, H: lid
H = 0.24 x Td + W (1061 + 0.444 x Td)
(H)ent = 0.24 X + (1061 + 0.444 x )

= Btu/lb
(H) lv , - 0.24 x + (1061 + 0.444 x )

“ Btu/lb
COMMENTS
A106
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM -{.COMPONENT TEST), COOLING COIL
continued Page 17
AH no Date
Precooling coil no.
Cooling coil no.
Check Fail &
lie Specific volume of air, v: lie

Note: Measurement location of Td and flow rate must be consistent
0.754 x (Td + 460)

v = (1 + 1.6078 x W)
Pb
0.754 x ( + 460)
(1 + 1.6078 x W) - cu ft/lb
Pb
Ilf Mass flow rate of air, M: Ilf
cfm cfm
M = lb/min
V
llg Coil cooling capacity, C: llg
C = 60 M x [(H) lvg - (H) ent ]
= 60 x x ( )
- Btu/h

Averaged coil heating capacity: 12
( + + ) /3 = Btu/h
13 Calculate coil or condenser pressure drop, P: 13
P = (P) pn , - (P) 1VB = II 4-1

> o
C > 0.95 x * capacity > 0.95 x >

P < 1 1 x * press drop < 1.1 x
.
< (coil or condenser)
AF < 1.1 x * air friction < 1.1 x <
COMMENTS :
A107
: :
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (60MP0NENT TEST), HUMIDIFIER
Page 18
AH no. Date
Humidifier no. ___________ Inspection agent
Make and model Commissioning team

Serial no.
Type

2. "*" and subscript "s" denote data required from specification,
Check Fail &


2 Measure entering air temp & humidity 2
F, % RH
3 Estimate leaving air humidity; leaving 3
air should not damage building and
equipment; otherwise postpone test
4 Measure & adjust steam temp & 4
pressure to within 1 psi of
specified
(* psi) psi F
Is steam saturated?
5 Set humidifier control to discharge 5
steam at full load
6 Run system for at least 10 minutes 6
intervals
Ent air temp

12 , ,
3
F
Lvg air temp , ,
F
Ent air humidity , ,
% RH
Lvg air humidity ,
% RH
COMMENTS
A108
APPENDIX
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM ^COMPONENT TEST), HUMIDIFIER
continued Page 19
AH no. Date
Humidifier no.
Check Fail &

8 Calculate humidifier capacity: 8

8a Saturated water vapor of air, Psw: 8a
= e ( 15 4638
. - [ 7284/ (Td-392 )
p
/ p \ = e,><15.4638 - [7284/ + 392)] in. Hg

v r sw/ent
/p \ = „(15.4638 - [7284/ + 392)] in. Hg

' r SW / lvg
8b Vapor pressure, Pw: 8b
P w - RH x P sw
( P w)ent = 0.5 X (Psw)ent = 0.5 X = in. Hg
( P w)lvg = 0- 5 x (Psw) lvg - 0.5 X = in.Hg
Humidity ratio, W: 8c
W = 0.622 x
pb - pw
(W)ent = 0.622 x = lb vapor/lb dry air
COMMENTS
A109
:
TEST WORK SHEET WS 5B-2 -- AIR HANDLING SYSTEM (COMPONENT TEST), HUMIDIFIER
continued Page 20
AH no. Date_
Hum i d i f i e r no.
Check Fail &

(W) lvg - 0.622 x lb vapor/lb dry air
8d Specific volume of air, v: 8d

0.754 x (Td + 460)

v _____ (i + 1.6078 x W)
Pb
0.754 x ( + 460)
-
(1 + 1.6078 x W) = cu ft/lb
Pb
8e Mass flow rate of air, M: 8e
cfm cfm
M = - - lb/min
v
8f Humidifier capacity, C: 8f
C = 60 M x [
(W) lvg - (W) ent ]
*= 60 x x ( - _) = Btu/n

Averaged humidifier capacity: 9
( + + _)/3 - Btu/h
10 Acceptance criteria 10
C > 0.95 x * capacity > 0.95 x >

Humidifier does not "spit"
COMMENTS
A110
APPENDIX
6.1 INSPECTION CHECK LIST CL 6A~1 — EMCS

Page 1
Supplier Date
System model Inspection agent
CPU make, model Commissioning team
CPU serial no.
NO.
5 DESCRIPTION YES NO N/A REMARKS NO
General
1 Control diagrams, 0 & M manuals complete 1
2 Specified test equipment complete:
2a PROM programmer 2a
2b FID/MUX tester 2b
6
2c Data environment simulator 2c
2d Others 2d

4 Any interfacing with existing system? If so: 4
4a Has existing system been tested? 4a
List items tested:
Are all required master control room (MCR) 5

equipment installed? Verify component
models with submittals:
Model Serial no.
5a CCU 5a
5b Disk drive 5b
5c Oper. console 5c
5d Graphic device 5d
5e Logging printer 5e
5f Alarm printer 5f
5g Others 5g
Verify field equipment models with 6

submittals
Make & Model Software version
6a FID 6a
6b Mux 6b
6c Temperature sensor 6c
6d Humidity sensor 6d
6e Pressure sensor 6e
6f Flow sensor 6f
Alll
:
INSPECTION CHECK LIST CL 6A-1 -- EMCS continued -

Page 2
Date
6g Temperature transmitter 6g
6h Humidity transmitter 6h
6i Pressure transmitter 6i
6j Flow transmitter 6j
6k Others 6k
7Equipment access space adequate 7

8Electrical connections tight, labeled 8
9 Equipmant and wiring grounding 9
(control room equipment, raised floor,
wire troughs and field equipment)
10 High and low voltage line separation 10
11 Integraty of electrical insulation 11
12 Identification of wires and terminals 12
13 FID & MUX cabinets as required 13
14 FID & MUX cabinet locks as required 14
Spare keys supplied as required
15 Indicating lights of FID & MUX as 15
required
16 Temperature sensors installed properly 16
17 Averaging temperature sensors required? 17
18 No apparant conduction loss of 18
temperature sensor supporting rod
19 No apparant radiation effect for 19
temperature sensor
20 Adequate protection from moisture for 20
temperature sensors on ch. water pipes
21 Humidity sensor installed properly 21
22 Water protection for humidity sensor 22
23 Pressure sensors installed properly 23
24 Flow sensing devices installed properly 24
25 Pressure & flow sensing devices have 25
flow straightners or adequate pipe
26 Adequate protection of transmitters for 26
high temperature
27 Equipment surface paint complete 27
28 Operation of dampers and valves, no 28
hunting noticed
COMMENTS
All 2
APPENDIX
6.2 TEST WORK SHEET WS 6B-1 — EMCS GENERAL

Page 1
Supplier Date
EMCS system model Inspection agent
CPU make .model Commissioning team
CPU serial no.
Software version

fill data as required. Initial under "pass" or "fail" columns.
Enter remarks if necessary.
Check Fail &

System general test:

1 Shut all EMCS equipment off 1
2 Energize all EMCS equipment: 2
2a Equipment in central control rm.: 2a
central control unit
storage unit
operator's unit
monitor
logging printer(s)
alarm printer(s)
display unit(s)
others
2b Field equipment 2b
FIDs
MUXs
others
3 Initiate system startup (see system 3
supplier's instructions)
4 Enter command to display content of 4
stored files:
program to load and initiate computer
operating program for peripheral devices
operating program for file management
text editor program
language processor
linking program
assembler
others
COMMENTS
A113
TEST WORK SHEET WS 6B-1 -- EMCS GENERAL continued-

Page 2
Supplier Date
EMCS system model
Software version
Check Fail &
5 Enter following commands from operator's 5

console to test system responses. When
system responds, check for correctness.
5a Log on with incorrect ID 5a
5b Log on with correct ID 5b
5c Enter at least 5 correct commands 5c
5d Enter at least 5 incorrect and incomplete 5d

commands and check error messages
5e Command to start certain HVAC equipment 5e

5f Command to stop certain HVAC equipment 5f
5g Command to disable certain FIDs 5g
5h Command to enable the FIDs disabled in 5g 5h
5i Command to disable certain MUXs 5i
5j Command to enable the MUXs disabled in 5i 5j
5k Command to disable certain sensor inputs 5k
51 Command to address the disabled sensors 51
in 5k
5m Command to enable the points in 5k 5m
5n Enter commands of higher access level 5n
than allowed
5o Enter commands for help function 5o
5p Enter invalid commands 5p
5q Cancel commands entered previously 5q
5r Command to display certain digital points 5r
5s Command to display certain analog points 5s
5t Command to change set point within 5t
limits of certain controllers
A114
APPENDIX
TEST WORK SHEET WS 6B-1 -- EMCS GENERAL continued

Page 3
Supplier Date
EMCS system model
Software version
Check Fail &
5u Command to change set point outside 5u

limits of certain controllers
5v Command to change high limits of 5v
certain control points
5w Command to change low limits of 5w
certain control points
5x Command to change certain scale factor 5x
5y Command control of certain equipment 5y
from EMCS to manual control
5z Command same equipment in 5y from 5z
manual to automatic mode
5aa Command to change time of certain 5aa
HVAC control actions
5bb Command to generate report and 5bb
examine report content and format:
All point report of all systems:
(enter system no.)
Trend of certain points:

(enter point no.)
Timed display of certain reports:
5cc Initiate alarm conditions of certain 5cc

points to generate alarm reports:
(enter point no.)
5dd Enter other commands 5dd

5ee Log off system 5ee
COMMENTS :
A115
:
6.3 TEST WORK SHEET WS 6B-2 —

EMCS OVERALL PERFORMANCE TEST,
TEMPERATURE, HUMIDITY, AND PRESSURE Page 1
Supplier Date
EMCS system model Inspection agent_
Software version Commissioning team

Check Fail &

Temperature, humidity, and pressure points:

Enter point no.
sensor kind__
service
test sensor in: pipe space_
(check one) duct
simulated
1 Prepare two way communication between 1

EMCS sensor location and central
control room
2 Place sensor in place 2
First point (low range):
3 If simulated environment is used, adjust medium 3

to around low range of sensor
4 Wait sufficient time for sensor 4
to stablize
5 Coordinate time between site and central 5
6 Take readings simultaneously 6
Reading of sensor at site
Reading at central control
COMMENTS
A116
APPENDIX
TEST WORK SHEET WS 6B-2 -- EMCS OVERALL PERFORMANCE TEST, TEMPERATURE,

HUMIDITY,
7 AND PRESSURE continued
Page 2
Supplier Date
EMCS system model
Software version
Check Fail &

Difference of two readings =
Second point (high range)
8 If simulated environment is used, adjust medium 8

to around 3/4 of high range of sensor
Set medium = 0.75 x * =
9 Wait sufficient time for sensor 9
to stablize
10 Coordinate time between site and central 10
11 Take readings simultaneously 11
Reading of sensor at site
Reading at central control
12 Difference of two readings = - 12
= gpm
*
COMMENTS
A117
:
6.4 TEST WORK SHEET WS 6B-3 — EMCS OVERALL PERFORMANCE TEST,

FLOW
Page 1
Supplier Date
HVAC system Commissioning team
Software version
N o t e s for using form:

Check Fail &

Flow points:
Enter point no.
sensor kind
service
1 Prepare two way communication between 1

EMCS sensor location and central
control room
2 Remove primary flow sensor from EMCS 2
3 Connect flow simulating instrument to EMCS 3
First point (zero flow):

4 Set simulating instrument to zero signal 4
5 Take a reading from central control 5
gP m
6 Difference of reading from zero ______ 6
Second point (high flow range):

7 Adjust simulating instrument to around 7
3/4 of equivalent high flow
Flow = 0.75 x * gpm = gpm ___
Equivalent flow signal:
For manometer in. w.c.
For count type counts/min
For other type ( )
8 Take a reading from central control 8

gpm
COMMENTS
A118
APPENDIX
TEST WORK SHEET WS 6B-3 -- EMCS OVERALL PERFORMANCE TEST, FLOW continued
Page 2
Supplier Date__
EMCS system model
HVAC system
Check Fail &
9 Calculate flow rate from data in 7

For manometer type flow (SE-37 or 39):
hw
(1/2)
Flow rate = 44.75 (K Y d 2 F a ) ( )
= 44.75 x x 2 x (-~.)U/2)
( )
= gpm
For turbine and vortex shedding type (SE-41)
Flow rate = 60 (f / k)
= 60 x (-77..)
gpm
For other types (provide calculations below)
10 Difference of calculated (in 9) and 10

central control indicated (in 8)
gpm
COMMENTS
A119
:
6.5 TEST WORK SHEET WS 6B-4 — EMCS OVERALL PERFORMANCE TEST,

FOR ENERGY CALCULATIONS
Page 1
Supplier Date
HVAC systm Commissioning team
Software version

Check Fail &

Instantaneous energy rate for water:
System
1 Command to print a set of all point 1

data for a system
2 Indicated water entering heat exchanger 2
temp F
3 Indicated water leaving heat exchanger 3
temp F
4 Calculate temperature difference 4
= - = F
5 Indicated water flow rate gpm 5
6 Calculate energy rate 6
- 500 x (temp difference) x (flow rate)
- 500 x x
“ _____ B tu /h
7 Indicated energy rate _____ 7
8 Compare calculated and indicated energy rates 8
COMMENTS
A120
APPENDIX
TEST WORK SHEET WS 6B-4 -- EMCS OVERALL PERFORMANCE TEST, FOR ENERGY
CALCULATIONS
continued Page 2
Supplier Date
EMCS system model
HVAC system_
Software version
Check Fail &
Instantaneous energy rate for steam:
System
1 Command to print a set of all point 1

data for a system
2 Indicated steam temperature F 2
3 Indicated steam pressure F 3
4 Indicated condensate temp

10 F 4
5 Indicated steam flow rate lb/h 5
6 Enthalpy of steam 6
(from 2,3 & steam table) = Btu/lb
7 Enthalpy of water (from 4 & steam table) 7
= _____ Btu/lb
8 Energy rate = (enthalpy of steam - enthalpy 8

of water) x steam flow rate
- ( - ) x
= _____ Btu/h
9 Indicated energy rate 9
Compare calculated and indicated energy rates 10
COMMENTS
A121
: :
CALCULATIONS
continued Page 3
Supplier Date
EMCS system model_
HVAC system
Software version
Check Fail &
Accumulated energy (to be tested for all

steam and water consumption)
System
1 Command to print energy consumption rate 1

(Btu/h) of system to be tested at 1 minute
intervals for 10 minutes in unit of Btu/h
2 Command to accumulate energy amount for 2
the same system and same time as in 1, Btu
3 Average the ten instantaneous energy 3
rates Btu/h
4 Calculate the total energy of the 10 minutes 4
= 10/60 x (from 3) = ______ Btu
5 Indicated energy of the same period 5

(from 2) «= Btu
6 Difference of calculated and indicated 6

energy -= (from 5) - (from 4)
- Btu
7 Percentage difference 7
«= [1 - ( _(from 6) / ( from 4) ]
x 100
%
COMMENTS
A122
APPENDIX
CALCULATIONS
continued Page 4
Supplier D ate
EMCS system model
HVAC system
Software version
Check Fail &
Accumulated energy (to be tested for all

electric consumption)
System
1 Command to print elec, energy consumption 1

rate (W) of system to be tested at
1 minute intervals for 10 minutes
2 Command to accumulate elec, energy amount for 2
the same system and same time as in 1 Wh ,
3 Average the ten instantaneous energy 3

rates W
4 Calculate the total elec, energy of the 10 minutes 4
= 10/60 x (from 3) = _
Wh
5 Indicated energy of the same period 5

(from 2) *= Wh
6 Difference of calculated and indicated 6

energy = _(from 5) - (from 4)
= Wh
7 Percentage difference 7
= [1 - ( (from 6) / (from 4) ]
x 100
%
COMMENTS
A123
:
6.6 TEST WORK SHEET WS 6B-5 — EMCS APPLICATION SOFTWARE TEST,

SCHEDULED START/STOP
Supplier Date
HVAC system Commissioning team
Software version

2. Program requirement varies, see project specification and change
test work sheet accordingly.
Check Fail &

1 System input: 1
Start time set
Stop time set
Days set: weekday
weekend
holiday
Season: heating
cooling
Time delay required? Delay time
2 Record current equipmant operation mode 2
on
off
3 Enter command to put equipment under 3
program
4 Observe equipment operation when set 4
time is reached and record equipment
operation mode
on
off
time delay time ____
5 Manually start or stop equipment 5
6 EMCS issues alarm 6
7 Test conclusion 7
COMMENTS
A124
APPENDIX

OPTIMUM START/STOP Page 1
Supplier Date
EMCS system model
HVAC system
Software version

3. Observation of equipment operation for this test should be at
equipment start/stop time which varies according to outdoor
conditions
Check Fail &

1 System input: 1
Days set: weekday
weekend
holiday
Season: heating
cooling
Time delay required? Delay time
2 Record current equipmant operation mode 2
on
off
program
COMMENTS
A125
:
TEST WORK SHEET WS 6B-6 -- EMCS APPLICATION SOFTWARE TEST, OPTIMUM START/STOP
continued Page 2
Supplier_ Date
EMCS system model
HVAC system
Check Fail &

Steps mark Pass Remarks No.
Optimum Start - :
4 Display representative space temperature 4

(or return air temperature) at close
intervals (e.g. 1 minute)
5 Observe equipment operation mode change 5
from off to on
When equipment is switched to
occupied mode record indoor air
temperature, F.
This temperature shall not differ
more than 3 F from specified room
temperature (or tolerance specified)
Optimum stop - :
6 Observe equipment operation mode change 6

from on to off
When equipment is stopped, keep
displaying indoor air temperature
until end of specified occupancy time,
space temp shall not differ more than
3 F from specified room temp during
occupied period (or as specified)
7 Manually start or stop equipment 7
8 EMCS issues alarm 8
9 Test conclusion 9
COMMENTS
A126
APPENDIX
6.8 TEST WORK SHEET WS 6B-7 *

— EMCS APPLICATION SOFTWARE TEST,
DUTY CYCLING
Supplier Date
EMCS system model
HVAC system
Software version

Check Fail &

1 System input: 1
Specified maximum space temp
Specified minimum space temp
Specified minimun cycling time min
duty cycling schedule program
3 Display space temperature (at 5 minute 3
intervals) and equipment operation
status
4 Verify that the equipment is cycling and 4
the space temp does not go beyond the
max. or min. specified temp
5 Enter command or reset temp controller 5
to raise or lower space set temp
6 Verify that the equipment is cycling and 6
the space temp does not go beyond the
max-min specified temp band
7 Verify that the specified minimum on 7
time is not violated during the entire
test period
8 Restore setting of temp controller 8
9 Test conclusion 9
COMMENTS
A127
:

ELECTRICAL DEMAND LIMITING Page 1
Supplier Date
EMCS system model
HVAC system
Software version

Check Fail &

1 System input: 1
Time applicable: start
end
Days applicable: weekday
weekend
holiday
Meter reset interval min
Average power kw
Equipment under control:
Equipment
12 3 4
name
Priority
level
Delay time
(min)
Min off
(min)
Min on
(min)
Max off
(min)
COMMENTS
A128
APPENDIX
TEST WORK SHEET WS 6B-8 -- EMCS APPLICATION SOFTWARE TEST, ELECTRICAL DEMAND
LIMITING continued Page 2
Supplier Date
EMCS system model
HVAC system_
Software version
Check Fail &
5 6 7 8
Equipment
name
Priority
level
Delay time
(min)
Min off
(min)
Min on
(min)
Max off
(min)
2 Enter command to put program in operation 2
3 Turn on HVAC equipment and/or increase 3
electric load
4 Verify equipment shut-down and record 4
equipment on/off time
Equipment
12 3 4
Time shed
Time restored
Off time (min)
On time (min)
5 6 7 8
Equipment
Time shed
Time restored
Off time (min)
On time (min)
5 Confirm that equipment shedding sequence 5
agrees with priority list
6 Confirm that equipment on/off times do not 6
exceed specified max and min limits
7 Confirm equipment rotation within 7
the same priority level, if specified
8 Test conclusion 8
COMMENTS :
A129
:

DAY-NIGHT SETBACK Page 1
Supplier Date
EMCS system model __
HVAC system
Software version

Check Fail &

1 System input: 1
weekend
holiday
Season: heating cooling
Setback time: start end ,
Occupied time set temp F

Unoccupied time set temp F
3 Enter setback time to 5 minutes 3
beyond current time
4 Confirm system operation changes when 4
time reaches setback time
For heating test:
5 Reset setback temp 3 F higher than 5

present space temp
6 Confirm system cycling to satisfy 6
temp setting
7 Confirm air damper positions in 7
accordance to spec
8 Change setback time so that current 8
control is under occupied time
9 Confirm system is under occupied 9
mode (e.g. fan and damper)
COMMENTS
A130
:
APPENDIX
TEST WORK SHEET WS 6B-9 -- EMCS APPLICATION SOEIWARE TEST, DAY-NIGHT SETBACK
continued Page 2
Supplier Date
EMCS system model
HVAC system
Check Fail &

For cooling test:
10 Reset setback temp 3 F lower than 10

present space temp
11 Confirm system cycling to satisfy 11
temp setting
12 Confirm air damper positions in 12
accordance with spec
13 Change setback time so that current 13
control is under occupied time
14 Confirm system is under occupied 14
mode (e.g. fan and damper)
15 Restore setback time and temp to 15
specified values
16 Test conclusion 16
COMMENTS
A131
:

DRY BULB ECONOMY CYCLE
Supplier Date
EMCS system model__
HVAC system
Software version

Check Fail &
1 System input: 1
Change-over temp F
3 Obtain a current report of system: 3
Outdoor air temp F
Return air temp F
Outdoor sir damper position
Return air damper position _____
Mixed air temp F
4 Compare outdoor air and change-over 4
temp .
if
,
T 0 a > T co go to steps 5 to 9
,
T oa < T co go to steps 8 to 12
,
5 Verify that outdoor damper is at 5

min OA position and return damper
position is appropriate
6 Verify that coil valve positions 6
are apporpriate
7 Raise change-over temp 3 F above 7
outdoor temp
8 Verify that outdoor and return 8
dampers are under local control (modulating)
are apporpriate
10 Lower change-over temp 3 F below 10
outdoor temp
11 Verify that outdoor damper is at 11
min OA position and return damper
position is appropriate
are apporpriate
14 Restore change-over temp setting 14
A132
: ,
APPENDIX
6.12 TEST WORK SHEET WS 6B-11 ~ EMCS APPLICATION SOFTWARE TEST

ENTHALPY ECONOMY CYCLE Page 1
Supplier Date
EMCS system model
HVAC system
Software version

Check Fail &

1 Confirm that program requires temp 1

and humidity of both outdoor and
return air
2 Enter command to put program in 2
operation
3 Obtain a current report of system: 3
Outdoor air temp F
Outdoor air humidity % RH or
F w b and
. .
F d.p.
Outdoor air enthalpy Btu/lb
Return air temp F
Return air humidity 1 RH or
F w.b. and
F d.p.
Return air enthalpy Btu/lb
4 Compare outdoor and return air 4

enthalpies. If:
H oa > H ra> g° to 5
H oa < H ra> 6° to 6
5 Verify that the OA damper is at min 5

position and RA damper position
is proper
COMMENTS
A133
: 3 .
TEST WORK SHEET WS 6B-11 -- EMCS APPLICATION SOFTWARE TEST, ENTHALPY ECONOMY
CYCLE continued Page 2
Supplier Date
EMCS system model_
HVAC system
Software version
Check Fail &

6 Substitute outdoor temp and humidity 6

sensors with simulators
7 Divide a psychromatic chart into 7

regions as outlined in paragraph
7. 5. 3. of EXHIBIT 5-B
8 Manipulate temp and humidity sensors 8

so that OA conditions are within
each of the regions where H oa < H ra
9 Verify that OA and RA damper 9

positions are in accordance with
specifications
Region OA RA
1
2
3
10 Restore temp and humidity sensors 10
COMMENTS
A134
: ,
APPENDIX
6.13 TEST WORK SHEET WS 6B-12 -- EMCS APPLICATION SOFTWARE TEST

VENTILATION AIR CONTROL Page 1
Supplier Date
EMCS system model
HVAC system
Software version

fill data as required. Initial under "pass” or "fail" columns.
2. Perform this test during occupied period.
3. This form is designed for specs requiring outdoor damper positions
be based on comparison of outdoor and space temp. Modify form if
the requirement is different.
Check Fail &

1 System input: 1
weekend
holiday
Season: heating cooling
,
Space temp: F
Occupied time: start
end
AH unit: start time
s t op time
2 Time of test 2
operation
4 Verify that OA damper is open 4
For heating mode test:

5 Change occupied/unoccupied schedule 5
so that current time is about 15
minutes before occupied period,
then go to step 6 or 9
6 If outdoor temp is higher than space 6
temp, verify that dampers are
under local loop control
COMMENTS
A135
:
TEST WORK SHEET WS 6B-12 -- EMCS APPLICATION SOFTWARE TEST, VENTILATION AIR
CONTROL continued Page 2
Supplier Date
EMCS system model
HVAC system
Check Fail &

10 Steps mark Pass Remarks No.
No.
7 Raise space temp setting 3 F above 7

outdoor temp
8 Verify that OA damper is closed 8
9 Lower space temp setting 3 F below 9

outdoor temp
Verify that dampers are under 10
local loop control
For cooling mode test:

11 Change occupied/unoccupied schedule 11
so that current time is about 15
minutes before occupied period,
then go to step 12 or 15
12 If outdoor temp is higher than space 12
temp, verify that outdoor damper
is closed to minimum position
13 Raise space temp setting 3 F above 13
outdoor temp
14 Verify that dampers are under 14
local loop control (modulating)
15 If outdoor temp is lower than space 15
temp, verify that dampers are
under local loop control
16 Lower space temp setting 3 F below 16
outdoor temp
17 Verify that outdoor damper is closed 17
18 Restore occupied/unoccupied schedule 18
and temp settings
COMMENTS
A136
: .
APPENDIX

EMCS APPLICATION SOFTWARE TEST,
HEATING/COOLING COIL TEMPERATURE RESET
Supplier_ Date
EMCS system model
HVAC system
Software version

Check Fail &
1 Coil type: heating ,

cooling 1
2 System input: 2
Reset upper temp limit F
Reset lower temp limit F
Index temp: outdoor temp
zone temp
Space humidity limit:
% RH, F w.b . ,
F d.p
operation
4a Substitute index temp sensor with temp 4a
simulator, or
4b Place index temp sensor in temp bath 4b
5 Increase simulated temp or bath temp 5
6 Observe coil discharge temp, it should 6
move lower
7 Verify that discharge temp does not go 7
below specified low limit
8 Decrease simulated temp of bath temp 8
9 Observe coil discharge temp, it should 9
move higher
10 Verify that discharge temp does not go 10
above specified high limit
11 For cooling coils which specify high 11
space humidity limits, change the
humidity limit to a lower level
12 Verify that the cooling coil discharge 12
temp decreases
13 Restore temp sensors 13
COMMENTS
A137
:

HOT WATER TEMPERATURE RESET
Supplier Date
EMCS system model
HVAC system _____
Software version __

Check Fail &

1 System input: 1
Reset schedule:
Outdoor temp HW temp
High F F
Low F F
operation
3a Substitute outdoor temp sensor with 3a
temp simulator, or
3b Place outdoor temp sensor in temp bath 3b
to below the high limit
5 Observe hot water temp, it should 5
move lower
to 5 F beyond high limit
7 Verify that hot water temp does not go 7
below specified limit
8 Decrease simulated temp or bath temp 8
to above low limit
9 Observe hot water temp, it should 9
move higher
10 Decrease simulated temp or bath temp 10
to 5 F beyond low limit
11 Verify that hot water temp does not go 11
above specified limit
12 Restore temp sensors 12
COMMENTS
A138
: ,
APPENDIX
6.16 TEST WORK SHEET WS 6B-15 •

EMCS -APPLICATION SOFTWARE TEST,
CHILLED WATER TEMPERATURE RESET Page 1
Supplier Date
EMCS system model
HVAC system
Software version

fill data as required. Initial under "pass" or "fail" columns,
Check Fail &
1 System input:
Reset schedule:
Space Valve
temp position CHW temp
High F % F
Low F % F
Space high humidity limit:
% RH
F wb
F dp
operation
3a Substitute space temp sensor with 3a
temp simulator, or
3b Place space temp sensor in temp bath, 3b
or
3c Be ready to change valve position sensor 3c
(or control signal feedback sensor)
4a Change temp simulator to raise temp 4a
(not over the limit) or
,
4b Raise bath temp (not over the limit) 4b

or
4c Move valve position or feedback sensor to 4c
indicate opening (not over the limit)
5 Verify that chilled water temp is 5
decreasing
6a Change temp simulator to raise temp 6a
3 F beyond limit, or
6b Raise bath temp 3 F beyond limit, or 6b
COMMENTS
A139
:
TEST WORK SHEET WS 6B-15 -- EMCS APPLICATION SOFTWARE TEST, CHILLED WATER
TEMPERATURE RESET continued Page 2
Supplier Date
EMCS system model
HVAC system^
Check Fail &

6c Move valve position or feedback sensor 6c

to indicate valve fully open
7 Verify that chilled water temp does 7
not drop below low limit
8a Change temp simulator to lower temp 8a
(not below the limit) or ,
8b Lower bath temp (not below the 8b

limit) or,

to indicate valve is closing (not over
the limit)
9 Verify that chilled water temp is 9
increasing
10a Change temp simulator to lower temp 10a
3 F beyond limit, or
10b Lower bath temp 3 F beyond limit, or 10b
toindicate fully closed valve
11 Verify that chilled water temp does 11
not increase above high limit
12 Substitute space humidity sensor with 12
humidity simulator
13 Change humidity simulator to raise 13
space humidity beyond high limit
14 Verify that chilled water temp 14
decreases
15 If more than one zone reset chilled 15
water temp, repeat procedures for
all zones
16 Restore temp, humidity, or position 16
(or feedback) sensors
COMMENTS
A140
: ,
APPENDIX

EMCS APPLICATION SOFTWARE TEST,
CONDENSER WATER TEMPERATURE RESET Page 1
Supplier Date
EMCS system model
HVAC system
Software version

Check Fail &

1 System input: 1
Reset schedule:
OA wet OA dry Cond water
bulb temp bulb temp temp
High F F F
Low F F F
Condenser water low limit F
operation
3 Substitute outdoor temp sensor with 3
temp simulator
4 Substitute outdoor humidity sensor 4
with humidity simulator
5 Manipulate temp and humidity sensors 5
to obtain desired successively
lower wet bulb temp (using a
psychromatric chart may be helpful)
and observe condenser water supply
temp
6 Record simulated outdoor conditions: 6
Dry bulb Humidity Wet bulb
temp ,
F temp ,
F
COMMENTS
A141
:
TEST WORK SHEET WS 6B-16 -- EMCS APPLICATION SOFTWARE TEST, CONDENSER WATER
TEMPERATURE RESET continued Page 2
Supplier Date
EMCS system model
HVAC system
Check Fail &

7 Verify that condenser water temp 7

decreases
8 Manipulate simulators to simulate 8

wet bulb temp 3 F below specified
low limit
9 Record simulated outdoor conditions: 9

Dry bulb temp F
Relative Humidity %
Wet bulb F
10 Verify that condenser water does 10

not drop below specified low limit
11 Restore temp and humidity sensors 11
COMMENTS
A142
: :
APPENDIX
7.1 INSPECTION CHECK LIST CL 7A-1 — FTRE SAFETY IN HVAC SYSTEMS

Date
Inspection agent
NO. DESCRIPTION YES NO REMARKS
General
1 All materials in plenums appropriate
2 Air filters appropriate
3 Fan inlets protected by screens
4 Heating equipment installation appropriate
5 Cooling equipment installation appropriate
6 Manual controls installed
7 Automatic controls installed
Ductwork:
1 Duct material appropriate
2 Duct installation appropriate
3 Duct connectors appropriate
4 Duct coverings appropriate
5 Duct linings appropriate
Duct access and inspection provisions:

1 Access at all required locations
2 Access properly identified
Dampers
1 Fire dampers located where required
2 Fire dampers of appropriate rating
3 Fire dampers installed appropriately
4 Ceiling dampers located where required
5 Ceiling dampers of appropriate rating
6 Ceiling dampers installed appropriately
7 Smoke dampers located where required
8 Smoke dampers of appropriate rating
9 Smoke dampers installed appropriately
10 Combination fire and smoke dampers
located where required
of appropriate rating
installed appropriately
COMMENTS
A143
: :
7.2 INSPECTION CHECK LIST CL 7A-2 —

FIRE SAFETY CONTROLS IN
HVAC SYSTEMS WITHOUT SMOKE CONTROL CAPABILITIES
Date
Inspection agent
NO. DESCRIPTION YES NO REMARKS
Manual shutdown
1 Appropriate fans stopped and started

2 Appropriate smoke dampers
fully and tightly closed
Automatic shutdown by return detector:

Automatic shutdown by supply detector:

Automatic shutdown by detector system:

COMMENTS
A144
APPENDIX
7.3 TEST WORK SHEET WS 7B-1 — ZONED SMOKE CONTROL SYSTEM

Page 1
Date
Test agent
NORMAL OPERATION TEST
Flow Direction:
Doors in barriers of smoke Pressure Difference From To
control zone (inches water gage) Zone Zone
:
TEST WORK SHEET WS 7B-1 -- ZONED SMOKE CONTROL SYSTEM (continued)

Page 2
Smoke Control Zone No.

Date
Test agent
SMOKE MODE TEST
NO. YES NO REMARKS

1. Fans operating appropriately
2. Smoke dampers in required position
3. Pass feedback test
Doors in Boundary of Smoke Pressure Difference

Control Zone (inches of water gage)
COMMENTS
A146
:
APPENDIX
TEST WORK SHEET WS 7B-1 -- ZONED SMOKE CONTROL .SYSTEM - DUCT MOUNTED DETECTOR
(continued) Page 3
Smoke Control Zone No.

Smoke Detector No.
Sensitivity Setting
Location of Detector
Date_
Test agent
DUCT MOUNTED DETECTOR SMOKE MODE TEST
NO. YES NO REMARKS

1. Fans operating appropriately
2. Smoke dampers in required position
3. Smoke detector in required position
4. Velocity pressure meets requirements
5. Smoke detector alarms in allowable time
6. Post-alarm operating sequence is proper
Air flow in duct cfm

Duct size
Minimum specified velocity pressure w.c.
Elasped time from smoke discharge to detector alarm sec
Note: Repeat test for each duct detector
COMMENTS
A147
7.4 TEST WORK SHEET WS 701 ~ PRESSURISED STAIRWELL SYSTEM

Page 1
Doors Open Date

Test agent
Stairwell No.
PRESSURE DIFFERENCE MEASUREMENTS
Doors in Pressurized Pressure Difference

Stairwell (inches water gage)
A148
:
APPENDIX
TEST WORK SHEET WS 7C-1 -- PRESSURIZED STAIRWELL SYSTEM (Continued)

Page 2
Date
Test agent
Stairwell No.
FLOW DIRECTION INDICATION
Flow Direction:
Doors Open in Pressurized From To
Stairwell Stair Stair
COMMENTS
A149
: :
8.1 INSPECTION CHECK LIST CL 8A-1 — ROOFTOP AIR CONDITIONING

UNIT
Page 1
ACU no. Date


Heating media: steam water ,
elec ,
gas (check one) ___
Stage of cooling: 1_ , 2 , 3 ,4 .
General
,
2
4 Component service space adequate 4
access doors, etc)
7 Equipment space clean, no fire hazards 7
10 Check valves and flow switches, flow 10
direction correct
14 Belt tightness satisfactory 14
16 Correct refrigerant kind 16
17 Correct refrigerant level 17
18 Compressor oil filter clean and proper 18
19 Correct compressor oil level: 19
Before operation
During operation
20 Cramkcase heater installed correctly 20
21 Crankcase heater on when unit off 21
COMMENTS
A150
APPENDIX
INSPECTION CHECK LIST CL 8A-1 -- ROOFTOP AIR CONDITIONING HANDLING UNIT

(continued) Page 2
ACU no. Date

32 Equipment labels complete and legible 32
33 Control air pressure correct (Pneumatic 33
control)
34 No excessive air leakage from unit 34
38 Unit location proper (relative to roof 38
structure)
39 Roof curb leveling correct 39
40 Roof curb weatherproofing proper 40
41 Sealing between roof curb and unit proper 41
42 All roof sleeves sealed correctly: 42
Ducts
Pipes
Wires
Conduits
Fan:
1 Housing access doors and latchs tight 1
2 Grease or oil tubes for bearings proper 2
3 No need removing belt guard for oiling 3
or speed check
5 Fans with inlet vanes or outlet dampers: 5
6 Protective hood over motor and belt for 6
outdoor installation
7 Inlet and outlet wire protection for fan 7
without duct connection
COMMENTS :
A151
: :
INSPECTION CHECK LIST CL 8A-1 -- ROOFTOP AIR CONDITIONING UNIT (continued)

Page 3
ACU no .
Date
Coils
la Heating coil la
lb Cooling coil lb
2a Heating coil 2a
2b Cooling coil 2b
3a Heating coil 3a
3b Cooling coil 3b
A Cooling coil drain pans and pipes 4
5b Strainers 5b
5c Air vents 5c
5d Sensor and thermometer wells 5d
5f Drain 5f
5g Others 5g
7 Condensate pipe at steam trap not over 7
200 F when control valve is open
(for low pressure steam only)
Air filters:
1 Filter frame securely anchored to casing 1
and unit casing
4 New (clean) filter media 4
COMMENTS
A152
: :
APPENDIX
7
Page 4
Check auto renewable filter advancing 7
mechanism
7a Motor 7a
7b Driving train 7b
7c Timer 7c
7d Pressure sensing 7d
7e Overriding operation 7e
7f Control operation 7f
8 Filter replacement space adequate 8
9 Spare filters to meet specifications 9
Air dampers:
opposed
Air louvers:
1 Material 1
2 Construction 2
3 Dimensions 3
4 Screen 4
Casings
1 Rigidity 1
2 Integraty 2
3 Access doors : 3
3a Size 3a
3b Gasket 3b
3c latches 3c
and ducts
COMMENTS
A153
:

Page 5
AHU no. Date
Thermal and acoustic insulation:

2 Material 2
3 Thickness 3
Automatic controls:
against contract documents and submittals
2 Observe general operation. Any obvious 2
incorrct settings and ranges?
10 Safety features (coil freeze protection, 10
etc.) installed correctly
11 Interlocking installed correctly 11
12 For controls interfacing with pneumatic
building system, check interfacing devices
13 For electrcal and electronic systems: 13
13a Wire connections tight 13a
13b No broken wires 13b
13c No rust, corrosion or film 13c
on wire terminals
13d Correct voltage on power supply 13d
13e Signal wires shielded correctly 13e
13f Shielding terminated at one end only 13f
COMMENTS
A154
: :
APPENDIX
8.2 INSPECTION CHECK LIST CL 8A-2 — COMPUTER ROOM AIR

CONDITIONING UNIT
Page 1
ACU no. Date


Electric reheat: yes ,
no
(check one)
General
4 Component service space adequate 4
access doors, etc)
7 Equipment space clean, no fire hazards 7

10 Check valves and flow switches. Flow 10
direction correct
16 Correct refrigerant kind 16
17 Correct refrigerant level 17
18 Compressor oil filter clean and proper 18
19 Correct compressor oil level: 19
Before operation
During operation
20 Crankcase heater installed correctly 20
21 Crankcase heater on when unit off 21
COMMENTS
A155
: . :
INSPECTION CHECK LIST CL 8A-2 -- COMPUTER ROOM AIR CONDITIONING UNIT

(continued)
Page 2
ACU no Date

32 Equipment labels complete and legible 32
33 No excessive air leakage from unit 33
Fan:
1 Housing access doors and latchs tight 1
2 Grease or oil tubes for bearings proper 2
3 No need removing belt guard for oiling 3
or speed check
5 Fans with inlet vanes or outlet dampers: 5
Coils
4 Cooling coil drain pans and pipes 4
5b Strainers 5b
5c Air vents 5c
5d Thermometer wells 5d
5f Drain 5f
5g Others 5g
COMMENTS
A156
. : .
APPENDIX

(continued)
Page 3
ACU no Date
Air filters:
1 Filter frame anchored to casing securely 1
and unit casing
7 Filter replacement spece adequate 7
8 Spare filters 8
Air dampers:
opposed
Casings
1 Rigidity 1
2 Integraty 2
3 Access doors: 3
3a Size 3a
3b Gasket 3b
3c latches 3c
and ducts
Thermal and acoustic insulation:

2 Material 2
3 Thickness 3
COMMENTS :
A157
:

(continued)
Page 4
AHU no. Date
Automatic controls:
against contract documemts and submittals
2 Observe general operation. Any obvious
10 2
incorrct settings and ranges?
Interlocking installed correctly 11
11a Control wire connections tight 11a
11b No broken control wires lib
11c No rust, corrosion or film 11c
on wire terminals
lid Correct voltage on power supply lid
lie Signal wires shielded correctly lie
Ilf Shielding grounded at one end only Ilf
12 Check operation of indicating lights 12
13 Check operation of audible alarms 13
14 Check dehumidifier operation for 14
units with variable air flow rates
when dehumidify is in operation
15 Check operation of underfloor water 15
detection system
16 Check operation of unit fire 16
detection system
17 Check operation of unit smoke 17
system
COMMENTS
A158
:
APPENDIX
8.3 INSPECTION CHECK LIST CL 8A-3 — PACKAGED TERMINAL

AIR-CONDITIONER
ACU no. Date
Make & model__ Inspection agent

Electric heat: yes no
,
(check one)

14 4 Electric wiring installation proper 4

5 Wire connections tight 5
6 No broken control wires 6
7 No rust, corrosion or film 7
on wire terminals
11 Surface finishing of thermal insulation 11
as required
13 Eequipment labels complete and legible 13
No unusual noise & vibration when running 14
15 Proper calibration of thermostat 15
19 Spare filters provided as required 19
20 Observe general operation of unit 20
21 Turn unit control knob at all stops 21
and thermostat settings to verify unit
operation:
fan (on/off)
compressor (on/off)
damper (open/close, closing tight)
heating element (on/off)
indicating lights
22 Inspect wall sleeve for proper 22
installation
23 Inspect around wall sleeve for seals 23
24 Inspect unit condensate disposing system 24
COMMENTS
A159
: .
8.4 TEST WORK SHEET WS 8B-1 -- INSTRUMENT CALIBRATION FOR

UNITARY AIR CONDITIONING UNIT
Page 1
Date
Test agent
Commissioning team

1. This work sheet is used for calibrating sensing devices and instruments
used in recording performance tests. Calibration of indicating devices
for equipment operations are covered under equipment test work sheets.
field with standard instruments. At leasttwo points covering the entire
range of normal operation should be calibrated. This work sheet lists
recommended calibration points. After final calibration, record data in
Block B.

Temperature
Humidity
Pressure
Power
Others
B. Final calibration data (set- temperature listed below may be changed

Instrument Approx. Std Final Approx Std . Final

No. Device Point Reading Reading Point Reading Reading No
Temperature, F:
1 Water (for condenser ,
32 200 1
steam, condensate,
and hot water)
3 Air 32 150 3
A160
: . ::
APPENDIX
TEST WORK SHEET WS 8B-1 -- INSTRUMENT CALIBRATION FOR UNITARY AIR CONDITIONING
UNIT continued Page 2
Date

Humidity:
4 Relative humidity, % 30#1 90#1 4
6 Wet bulb temp, F 35#2 75//2 6
Flow:
a
b.
c
8 Air velocity, fpm, 0 1000 8

Also see #5
Pressure
9 Air, in. w.c. 0 #6 9
Other devices:
a
b.
c
Notes
#4 25% above specified values
#5 This is for velocity type instrumsnts, see pressure calibration
for pressure sensing devices (pitot)
#6 Expected highest pressure or 5 in. w.c. whicherever is higher
Comments
A161
:
8.5 TEST WORK SHEET WS 8B-2 UNITARY ROOFTOP AND COMPUTER ROOM
UNIT, AIR FLOW RATE TEST Page 1
AH unit no._ Date __

Serial no. Commissioning team_

Type: (check one) Rooftop
Computer room

Check Fail &


for constant air volume system:
at minimum position
4 Measure barometric pressure • Hg 4
Phases 1-2 _____ V
Phases 2-3 V
Phases 3-1 V
Phases 1-2 V
Phases 2-3 _ V
Phases 3-1 V
COMMENTS
A162
: :
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND .COMPUTER ROOM UNIT, AIR FLOW
RATE TEST continued Page 2
AH unit no. Date
Check Fail &

6 Measure supply air fan performance: 6

(6b through 6g not required for
units without external ductwork)
6h Fan speed rpm 6h
Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
7 Check 10% of supply air outlets 7
7a Room ,
Room measured cfm (* cfm)
Room ,
Room ,
Error = %
Room Error = %
Room Error = %
Room Error = %
Room ,
Error = %
7c If 10% of 7b is outside +/- io%, 7c

COMMENTS
A163
: . .
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND COMPUTER ROOM UNIT, AIR FLOW
AH unit no. Date
Check Fail &

7d Room measured ,
cfm (* cfm) 7d
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room Error - ,
%
Room Error = ,
<y
Room Error = ,
%
Room Error = ,
%
Room Error *= ,
%

(1 - measured/specified supply) x 100% «= %

WS 2C-1 or 2C-2 ( cfm) (* cfm)
13c Static p at fan inlet in.w.c 13c
COMMENTS
A164
: .
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, AIR FLOW
RATE TEST continued Pa g e 4
AH unit no. Date
Check Fail &

13i Motor current and name plate FL current 13i

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
14 Set outside air damper to 100% OA 14
15 Set return air damper 15
16 Set relief air damper 16
17 Measure supply fan motor current: 17

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
18 Measure return fan motor current: 18

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
20 Check 10% of return air outlets: 20
Room »
Room »
Room »
Room »
Room »
Calculate error 20b

Room >
Error = %
Room »
Error = %
Room >
Error = %
Room >
Error = %
Room »
Error = %
COMMENTS
A165
: .
AH unit no. Date
Check Fail &

20c If 10% of 7b is outside +/- io%, 20c

check another 10% of s upply outlets
20d Room measured ,
cfm (* cfm) 20d
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room measured ,
cfm (* cfm)
Room Error = ,
%
Room Error = ,
%
Room Error = ,
%
Room Error = ,
%
Room Error = ,
%

22 Total air flow rate of measured outlets__ cfm (7a & 7d) 22
COMMENTS
A166
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, AIR FLOW
AH unit no. Date

5
Check Fail &

for variable air volume system:

at 100% OA position
Measure electric service voltage: 5

Phases 1-2 V
Phases 2-3 V
Phases 3-1 V

Phases 1-2 V
Phases 2-3 V
Phases 3-1 V
6 Select 10% of VAV boxes:

6a Lower rm. thermostats 5 F to measure max. flow, note 6a
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box # measured
,
cfm (* cfm)
Box y/ measured
,
cfm (* cfm)
Raise rm. thermostats 10 F to measure min. flow 6b
operation of reheat co il/recirculating fan:
Box y/ measured
,
cfm (* cfm)
Box y/ measured
,
cfm (* cfm)
Box y/ measured
,
cfm (* cfm)
Box y/ measured
,
cfm (* cfm)
Box y/ measured
,
cfm (* cfm)
COMMENTS
A167
: : ;
;
AH unit no. Date
Check Fail &

6c Calculate error: 6c
Box # ,
Error = % (max) Error «= % (min)
Box # ,
Error = % (max) Error - % (min)
Box # ,
Error = % (max) Error -= % (min)
Box // ,
Box # ,
7 If 10% of VAV boxes measured are

outside +/- 10%, check another 10% of boxes:
7a Lower rm. thermostats 5 F to measure max. flow, note
Box // measured ,
cfm (* cfm) 7a
Box # measured ,
cfm (* cfm)
Box // measured ,
cfm (* cfm)
Box // measured ,
cfm (* cfm)
Box # measured ,
cfm (* cfm)
Raise rm. thermostats 10 F to measure min. flow, note
Box # measured ,
cfm (* cfm) 7b
Box # measured ,
cfm (* cfm)
Box # measured ,
cfm (* cfm)
Box // measured ,
cfm (* cfm)
Box # measured ,
cfm (* cfm)
Calculate error 7c
( 1 - me asured/specif ied supply) x 100%
Box # Error =
,
%(max); Error = %(rain)
Box // Error =
, % (max) Error *= %(min)
Box # Error,
= % ( max ) Error -= %(min)
Box # Error,
= % (max) Error *= %(min)
Box # Error,
= % (max) Error = %(min)
COMMENTS
A168
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND XOMPUTER ROOM UNIT, AIR FLOW
AH unit no. Date
Check Fail &

8 If 10% of the VAV boxes measured in 6 & 7 are 8

outside +/- 15%, rebalance system.
9 Total air flow rate of measured boxes cfm (max) 9
10 Total air flow rate of specified _cfm (max) 10
11 Total air flow rate of measured boxes cfm (min) 11
12 Total air flow rate of specified cfm (min) 12
13 Calculate error: 13
(1 - measured/specified supply) x 100% «= % (max)
(1 - measured/specified supply) x 100% = % (min)
15 Measure and record duct static pressure at fan 15

static pressure sensor locations:
Sensor //I measured "w.c. (shown on control dwg "w.c.)
16 Measure duct static pressure at branch ducts 16

before last VAV boxes:
Branch 1 measured "w.c.
17 Specified minimum static pressure * "w.c. 17
18 Any branch must be: 18

* w.c. < measured press < measured press + 0.2"w.c.
COMMENTS
A169
:
19 Date
AH unit no.
Check Fail &

Record supply air fan performance: 19

WS 2C-1 or 2C-2 (_ cfm) (* __cfm)
19c Static p at fan inlet _in.w.c. 19c
19d
20 Total p at fan outlet in.w.c. 19d
19e Static p at fan outlet _in.w.c. 19e
19f Velocity p at fan inlet _in.w.c. 19f

L eaci 1 amp (* amp)
Lead 2 amp (* amp)
Lead ^ amp (* amp)

WS 2C-1 or 2C-2 ( cfm) (* cfm)
20c Static p at fan inlet _in.w.c. 20c
20g Velocity p at fan outlet _in.w.c. 20g

Lead 1 amp (* amp)
Lead 2 amp (* amp)
Lead 3 amp (* amp)
Restore damper controls 21
COMMENTS
A170
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND .COMPUTER ROOM UNIT, HEATING
CAPACITY TEST continued Page 10
AH unit no .
Date
Heating medium: Steam Inspection agent
(check one) Water Commissioning team

Elec_
Gas

Check Fail &

Heating capacity:
1 Air flow rate (from air flow rate test, 1
WS-2,page 2) cfm
2 Measure entering air temp 2
apply false load if needed
(* F)
average temp F
1 F of specified (water coil only)
(* F) F
A Measure & adjust steam temp & 4
pressure (steam coil only) to
within 1 psi of specified
(* psi) psi F
Is steam saturated?
5 Measure and adjust water or steam 5
flow rate to within 3 1 of specified
(water or steam coil only)
6 Disable control of test coil (water 6
or steam coil only)
7 Check electric coil is energized
(electric coil only) 7
8 Check gas burner is on (gas unit only) 8
COMMENTS
A171
: ]
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND COMPUTER ROOM UNIT, HEATING
AH unit no. Date_
Check Fail &


average lvg air temp:
,
F
at 5 min intervals:
Ent air temp

12 ,
3
F
Lvg air temp , ,
F
13 Calculate heating capacity: 13
13a Saturated water vapor, Psw: 13a
P sw A [15.4638 - 7284/ (Td+392 )

r ,= e
(Psw)ent - e'
15 * 638 - 728 * /( + 392 ” = in. Hg
13b Vapor pressure, P w : 13b
Pw - RH x P sw
(Pw)ent = °- 5 X ( P sw)ent = °- 5 x __ “ In.Hg
COMMENTS
A172
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, HEATING
AH unit no. Date
Check Fail &

W -= 0.622 x
Pb " Pw
(W)ent = 0.622 x = lb vapor/lb dry air
(W) lvg - (W) ent - lb vapor/lb dry air
13d Enthalpy, H: 13d
H = 0.24 x Td + W (1061 + 0.444 x Td)
( H ) ent = 0-24 x + (1061 + 0.444 x ) - Btu/lb
(H)iv 8 = 0.24 x + (1061 + 0.444 x ) = Btu/lb
13e Specific volume of air, v: 13e

0.754 x (Td + 460)

(1 + 1.6078 x W)
Pb
0.754 x ( + 460)
-
(1 + 1.6078 x W) = cu ft/lb
Pb
COMMENTS
A173
: ,
TEST WORK SHEET WS 8B-2 UNITARY ROOFTOP AND COMPUTER ROOM UNIT, HEATING
AH unit no. Date
Check Fail &

13f Mass flow rate of air, M: 13f
cfm cfm
M Ib/min
13g Coil heating capacity, C: 13g
C - 60 M x [(H) lvg - ( H ) ent ]
” 60 x x ( - )
= Btu/h
13h Repeat calculations for all 3 sets of data,

Averaged heating capacity: 13h
( )/3 = Btu/h
C > 0.95 x * capacity > 0.95 x
COMMENTS
A174
: ,
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, COOLING
AH unit no. Date

Inspection agent
Commissioning team

Check Fail &

1 For air cooled condensing system, 1

measure outside air temp; if it
differs more than 2 F from
specified, postpone test
(* F) F
2 For water cooled condensing system, 2
measure and adjust condensing w
temp to within 2 F from specified
(* F) F;
measure and adjust cond w flow
rate to within 3% of specified
(* KPrc) gP m
WS-2, page2) cfm
4 Measure entering air temp & 4
humidity; apply false load
if needed
(* F, * % RH)
average temp F, % RH
3 Make sure cooling is on during test 5
COMMENTS
A175
: ( ]
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND COMPUTER ROOM UNIT, COOLING
AH unit no. Date
Check Fail &


at 10 min intervals:
Ent air temp

12 ,
3
F
Lvg air temp , ,
F
Ent air humidity , , %
Lvg air humidity , %
9 Calculate cooling capacity: 9

P CW
^ «=
“ -[15.4638
“ - 7284/ (Td+392 )
-
i
\
sw/ent
= c-[15.4638 7284/ + 392)] „ in. Hg
-
'
\ _ e-[15.4638 7284/ + 392)) = in. Hg
sw/ent
9b Vapor pressure, Pw: 9b
P w - RH x P sw
(Pw)ent = 0.5 X ( P sw)ent “ °-5 X *= in.Hg
(Pw)lvg = 0.5 X (P*w)lv K = 0.5 X = in.Hg
COMMENTS
A176
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, COOLING
CAPACITY TEST continued Pa g e 16
AH no. Date
Check Fail &

W - 0.622 x
(W)ent - 0.622 X - lb vapor/lb dry air
(W) lvg = 0.622 x = lb vapor/lb dry air
9d Enthalpy, H: 9d
H = 0.24 x Td + W (1061 + 0.444 x Td)
(H) ent « 0.24 x + (1061 + 0.444 x )

' Btu/lb
(H) lvg *= 0.24 x + (1061 + 0.444 x )

- Btu/lb
9e Specific volume of air, v: 9e

0.754 x (Td + 460)

v = (1 + 1.6078 x W)
Pb
0.754 x ( + 460)
= (1 + 1.6078 x W) = cu ft/lb
Pb
COMMENTS
A177
:
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND COMPUTER ROOM UNIT, COOLING
AH no. Date
Check Fail &

9f Mass flow rate of air, M: 9f
cfm cfm
M - ----- - lb/min
_
v
9g Coil cooling capacity, C: 9g
C « 60 M x [(H) lvg - (H) ent ]
= 60 x x ( - ) = Btu/hr
9h Repeat calculations for all 3 sets of data,

Averaged heating capacity: 9h
( + + )/3 = _____ Btu/h
C > 0.95 x * capacity > 0.95 x >
COMMENTS
A178
: :
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, HUMIDIFIER
AH unit no. Date

Type Inspection agent
Commissioning team

Check Fail &


WS-2, page 2) cfm
2 Measure entering air temp & humidity 2
F, % RH
3 Estimate leaving air humidity; leaving 3
air should not damage building and
equipment; otherwise postpone test
4 Measure & adjust steam temp & pressure 4
to within 1 psi of specified (for
unit with steam humidifier only)
(* psi) psi F
Is steam saturated?
5 Set humidifier control to full 5
capacity
6 Run system for at least 10 minutes 6
intervals
Ent air temp

12 , ,
3
F
Lvg air temp , ,
F
Ent air humidity , ,
% RH
, Lvg air humidity , ,
% RH
COMMENTS
A179
: ] .
TEST WORK SHEET WS 8B-2 UNITARY ROOFTOP AND COMPUTER ROOM UNIT, HUMIDIFIER
AH unit no. Date
Check Fail &

8 Calculate humidifier capacity: 8

,[15.4638 - 7284/ (Td+392 )
,[15.4638 - 7284/ ( + 392)] in. Hg

(Psw)
sw7 ent
[15.4638 - 7284/ (_ + 392)]

(Psw) ent in. Hg
8b Vapor pressure, Pw : 8b
P„ « RH x P sw
(Pw)ent - 0.5 X ( Psw) ent = 0.5 X in.Hg
(Pw)lvg “ °- 5 X (Psw)lvg - 0.5 X in. Hg
Pw
W - 0.622 x
Pb ' Pw
(W) ent 0.622 x lb vapor/lb dry air
(W) lvg 0.622 x lb vapor/lb dry air
COMMENTS
A180
:
APPENDIX
TEST WORK SHEET WS 8B-2 -- UNITARY ROOFTOP AND -COMPUTER ROOM UNIT, HUMIDIFIER
AH unit no. Date
Check Fail &

8d Specific volume of air, v: 8d

0.754 x (Td + 460)

v (1 + 1.6078 x W)
Pb
0.754 x ( + 460)
(1 + 1.6078 x W) cu ft/lb
Pb
8e Mass flow rate of air, M: 8e
cfm cfm
M= - lb/min
v
8f Humidifier capacity, C: 8f
C = 60 M x [(W) lvg - (W) ent ]
= 60 x x ( - ) = Btu/hr
8g Repeat calculations for all 3 sets of data,

Averaged heating capacity: 8g
( + + )/3 = _____ Btu/h
C > 0.95 x * capacity > 0.95 x >

Humidifier does not "spit"
COMMENTS
A181
:
8.6 TEST WORK SHEET WS 8B-3 — UNITARY PTAC TEST

AH unit no. Date
Room no. Inspection agent
Make & model Commissioning team_

Heating type: Hot water_
(check one) Electric
Note for using form:

Follow the steps outlined in the form and place check marks or
Check Fail &

1 Verify ARI certification symbol (if 1

specified)
2 Turn unit control to on, verify 2
10
fan operation
3 Turn ventilation control to off 3
4 Turn cooling control to on, make sure 4
thermostat setting is at least 10 F
belo room temperature
T
5 Measure discharge air temperature, 5

discharge air is below 60 F
6 Turn heating control to on, make sure 6
thermostat setting is at least 10 F
below room temperature
7 If system is hot water, make sure 7
hot water temperature is as specified
8 Measure discharge air temperature, 8
discharge air is above 120 F
9 Turn ventilation control to on 9
Verify ventilation air damper is open 10
COMMENTS
A182
on hUMDtn
NIST-1 14A U.S.DEPARTMENT OF COMMERCE 1.
(REV. 3-69) NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY NISTIR 974”?

2. PERFORMING ORGANIZATION REPORT NUMBER
BIBLIOGRAPHIC DATA SHEET 3. PUBLICATION DATE

MARCH 1992
1 1. TITLE AND SUBTITLE
HVAC Functional Inspection and Testing Guide
S. AUTHOR(S)
James Y. Kao
5. PERFORMING ORGANIZATION (IF JOINT OR OTHER THAN NIST, SEE INSTRUCTIONS) 7. CONTRACT/GRANT NUMBER
DEPARTMENT OF COMMERCE
U.S.
NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY
GAITHERSBURG, MD 20899 8. TYPE OF REPORT AND PERIOD COVERED
9. SPONSORING ORGANIZATION NAME AND COMPLETE ADDRESS (STREET, CITY, STATE, ZIP)
General Services Administration

18th & F Streets, N.W.
Washington, DC 20405
10. SUPPLEMENTARY NOTES
DOCUMENT DESCRIBES A COMPUTER PROGRAM; SF-1BS, FIPS SOFTWARE SUMMARY, IS ATTACHED.

111. ABSTRACT (A 20O-WORD OR LESS FACTUAL SUMMARY OF MOST SIGNIFICANT INFORMATION. IF DOCUMENT INCLUDES A SIGNIFICANT BIBLIOGRAPHY OR
LITERATURE SURVEY, MENTION IT HERE.)
This guide is developed for the Public Building Service (PBS) of the General Services
Administration (GSA) for final inspection and testing of heating, ventilating, and air-
conditioning (HVAC) systems in Federal buildings prior to Government acceptance. The
guide describes in detail the functional inspection and testing procedures and
calculations. It includes eight chapters: General, Instrumentation and Basic
Measurement, Refrigeration Plant, Heating Plant, Air Handling Equipment and systems.
Building Automation Systems, Fire Safety Air Moving Systems, and Unitary Air Handling
Equipment. The appendix contains detailed inspection checklist and test work sheets
designed to be used in the field.
12. KEY WORDS (6 TO 12 ENTRIES; ALPHABETICAL ORDER; CAPITALIZE ONLY PROPER NAMES; AND SEPARATE KEY WORDS BY SEMICOLONS)
air handling system test; building automation system test; commissioning; field test; fire
safety test; functional test; heating plant test; inspection; smoke control test;
refrigeration plant test
13. AVAILABILITY
' — 14. NUMBER OF PRINTED PAGES
JL UNLIMITED
FOR OFFICIAL DISTRIBUTION. DO NOT RELEASE TO NATIONAL TECHNICAL INFORMATION SERVICE
429
(NTIS).
ORDER FROM SUPERINTENDENT OF DOCUMENTS, U.S. GOVERNMENT PRINTING OFFICE 15. PRICE
WASHINGTON, DC 20402.
A19
ORDER FROM NATIONAL TECHNICAL INFORMATION SERVICE (NTIS), SPRINGFIELD, VA 22161.
ELECTRONIC FORM

Nistir4758 PDF

Uploaded by

Copyright:

Available Formats

Nistir4758 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nistir4758 PDF

Uploaded by

Copyright:

Available Formats

A 11 ID 3 7377T5

HVAC Functional Inspection and

Building and Fire Research Laboratory

HVAC Functional Inspection and

This project is sponsored by the U.S. General Services Administration. The

CHAPTER 2 BASIC MEASUREMENT 9

EXHIBIT 2 -A FIELD TEST INSTRUMENTS 11

EXHIBIT 2-C STANDARD TEST PROCEDURES 28

CHAPTER 3 REFRIGERATION PLANT . 33

EXHIBIT 3 -A INSPECTION PROCEDURES FOR REFRIGERATION

EXHIBIT 3-E ABSORPTION REFRIGERATION MACHINE TEST

CHAPTER 4 HEATING PLANT 99

EXHIBIT 4 -A INSPECTION PROCEDURES FOR BOILERS AND

EXHIBIT 4—C TEST PROCEDURES FOR AIR-HEATING FURNACES . 125

CHAPTER 5 AIR HANDLING EQUIPMENT AND SYSTEMS . 137

EXHIBIT 5-A INSPECTION PROCEDURES FOR AIR HANDLING

CHAPTER 6 BUILDING AUTOMATION SYSTEMS ..... 171

EXHIBIT 6 -A INSPECTION PROCEDURES FOR BUILDING

EXHIBIT 6-B TEST PROCEDURES FOR BUILDING AUTOMATION

CHAPTER 7 FIRE SAFETY AIR MOVING SYSTEMS 195

EXHIBIT 7 -A FIRE SAFETY INSPECTION PROCEDURES FOR AIR

CHAPTER 8 UNITARY AIR CONDITIONING EQUIPMENT ......... 209

EXHIBIT 8 -A INSPECTION PROCEDURES FOR UNITARY AIR

APPENDIX (Inspection Check Lists and Test Work Sheets) ......... Al

2. Purpose. Commissioning serves to improve project quality through the

3. Organization of This Guide.

3.1.1 The main body formulates basic inspection and test

3.1.2 Recommended inspection check lists and test work sheets to

Often used test procedures are called Standard Test Procedures in

Not all procedures identified apply to all equipment and systems of

4. The Commissioning Team.

4.2 The commissioning team must be able to understand and to interpret

Testing and operation of equipment and systems during commissioning

4.5 The PBS construction engineers will coordinate the commissioning

5. Designated Inspection and Testing Agent.

5.2 almost always be the installing contractor and/or manufacturer of

Designated testing agents may be employees of the equipment

6. Codes, Regulations, and Standards. Where codes, regulations, and

a. American Society of Heating, Refrigerating, and Air-Conditioning

b. American Society of Mechanical Engineers (ASME)

c. Air-Conditioning and Refrigeration Institute (ARI).

d. National Fire Protection Association (NFPA)

e. Underwriters Laboratories (UL)

f . Sheet Metal Contractors National Association (SMACNA)

7. General Principles. Inspect and test HVAC equipment and systems to

7.1 All components and systems must meet project specifications

7.2.1 For the equipment and systems whose submittals are

as noted, pay special attention to the items noted as conditions of approval.

7.2.3 In no case should rejected equipment and systems be

7.2.4 For equipment and systems where submittals are not

7.2.5 Verify the performance of equipment and systems to meet

7.3 The inspection and functional testing procedures outlined in this

7.5 Temporary measures (such as temporary piping hookups) may be

7.6 The specification of each project must specify the scope of

8. Procedures and Sequences.

8.2 Steady-state tests. Steady-state tests are usually used to verify

8.3 Operation tests. These tests should be performed after the

8.4 Factory tests. Where specifications require factory testing of

8.5 Inspections and tests may be performed concurrently, if time and