‘I’ Scheme

CURRICULUM RE-DESIGN PROJECT

2019

QUESTION PAPER PROFILE,

SAMPLE QUESTION PAPER,
SAMPLE PROGRESSIVE TEST PAPERS
FOR

COURSE TITLE: Industrial Engineering and Quality

Control
(Course code: )

Programme Name:Mechanical Engineering

(Programme code: )

SIXTH SEMESTER

2019

1
 MAHARASHTRA STATE
BOARD OF TECHNICAL EDUCATION, Mumbai
(Autonomous) (ISO 9001:2008) (ISO/IEC 27001:2005)

2
 SAMPLE QUESTION PAPER

Guided by NITTTR Bhopal Resource Persons

S.No. Name and Designation Department

1 Dr. Ernest Joshua Professor NITTTR Bhopal

List of Contributors
MSBTE Course Experts

S.No. Name and Designation Institute

1
2
3 Prof N S Salunke SVC Polytechnic, Pune

Maharashtra State Board of Technical Education,

49, Kherwadi, Aliyawar Jung Road, Bandra (East), Mumbai-400051.
Maharashtra State, India.

MAHARASHTRA STATE BOARD OF TECHNICAL

EDUCATION, MUMBAI.

This is to certify that

3
 1. We the undersigned, have prepared sample question paper and two progressive test
papers of the course Industrial Engineering and Quality Control (Course code:
……………….) of VI semester of (Programmename)Mechanical Engineeringas per
Outcome based curriculum-‘I’ schemeof MSBTE, Mumbai.

2. Specification table has been attached and question paper profile of the course has
been prepared and due care is taken to prepare sample question paper so that there is
no mismatch / mistake in it.

MSBTE Course Experts

1. Name:- Prof. S.S. Harip
Instt Code- 006, Mobile No. 9890055381
2. Name- mngesh mahajan
3. Name prof N S Salunke
Instt Code- 0040 Mobile- 9373533580

Specification Table
Programme name: Mechanical Engineering Programme code:
Course Title: Industrial Engineering and Quality Control Course code:
Semester: Sixth

4
 Unit Unit Title Distribution of Theory Marks
R U A Total
Level Level Level Marks
I Work Study (Method Study 2 04 06 12
and Work Measurement)
II
02 04 06 12
Process Engineering
III
02 04 06 12
Ergonomics
IV
02 04 12 18
Quality Control& Inspection
V Statistical Quality Control
02 06 08 16

Total
10 22 38 70

R =Remember U= Understand A= Apply and above

5
 QUESTION PAPER PROFILE

Programme Name:Mechanical Engineering

Programme Code:
Course Title: Industrial Engineering and Quality Control
Course code:
Semester: Sixth
Q. Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Option Marks
No. s
T L M T L M T L M T L M T L M T L M T L M

1 1 R 2 2 R 2 3 R 2 4 R 2 4 R 2 5 R 2 5 R 2
5(7) 10(14)
2 1 U 4 2 U 4 3 U 4 4 U 4                  
3(4) 12(16)
3 1 U 4 1 A 4 2 U 4 3 U 4            
      3(4) 12(16)
4 2 A 4 3 A 4 3 A 4 4 A 4 5 A 4            
3(5) 12(20)
5 1 A 6 4 A 6 5 A 6                        
2(3) 12(18)
6 4 A 6 5 A 6 5 A 6
2(3) 12(18)
TOTAL 70(102
)

T=Topic/Unit Number L=Level of Question M=Marks

R =Remember U= Understand A= Apply and above

6
 Sample Question Paper:

Exam Paper code:

Seat No.

Maharashtra State Board of Technical Education

Scheme – I
ProgrammeName: Mechanical Engineering
Programmecode: Semester:VI Sem
Course Title: Industrial Engineering and Quality Control
Course code:
Marks :70 Time:3Hrs.

Instructions:
(1)All questions are compulsory.
(2)Illustrate your answers with neat sketches wherever necessary.
(3)Figures to the right indicate full marks.
(4)Assume suitable data if necessary.
(5)Preferably, write the answers in sequential order.

Q.1) Attempt any FIVE of the following. 10 Marks

a) Define Method Study. State its objectives.
b) state the factors of production
c) Enlist various QC tools
d) Name the various control charts in SQC
e) State the types and location of display.
f) State the characteristics of Quality
g) State the merits of acceptance sampling.
Q.2) Attempt any THREE of the following. 12 Marks
a) Explain in brief different "Recording Techniques" used in Method study
b) Explain part print analysis.
c) Explain Ergonomic considerations applied to types and location of display
d) Differentiate between Inspection & quality control

Q.3) Attempt any THREE of the following. 12 Marks

a) Define process chart .draw the symbols used in process chart
b) Prepare a two handed process chart for a task of sharpening the pencil with
appropriate process chart symbol
c) State considerations for selection of manufacturing processes for a given product
d) Redesign the given simple levers/knobs for specific applications.

7
Q.4) Attempt any THREE of the following. 12 Marks
a) State the steps in ergonomic design
b) Redesign the given simple crank or hand wheel for particular machine part.
c) With suitable example explain the criterion for machine selection.
d) Explain in detail OC curve and show following element on OC curve. 
i) α-Risk 
ii) β-Risk 
iii) AOQ 
iv) LTPD
e)  In a manufacturing process the number of defectives found in the inspection of 10
lots of 400 items each are given below

lot Number 01 2 3 4 5 6 7 8 9 10

No. of defectives
2 0 14 3 1 18 6 0 3 6

Determine the trial control limits for np chart.

Q.5) Attempt any TWO of the following. 12 Marks

a) Outline an appropriate process chart for the activity "replace old battery of car
b) Draw and explain Histogram, Pareto chart and Scatter diagram.
c) 10 samples of size 5 have been collected with following observations :

Sr. 1 2 3 4 5 6 7 8 9 10
No.

–X 2.011 2.008 2.001 2.003 1.998 1.995 1.997 1.997 2.002 2.003

R 0.011 0.017 0.009 0.026 0.27 0.21 0.014 0.017 0.023 0.015
Given A2 = 0.577, D3 = 0, D4 = 2.114
Draw the appropriate control chart

Q.6) Attempt any TWO of the following. 12 Marks

a) Draw the X –R control chart and explain the following terms on it

i. Extreme variations ii. Shift iii. Indication of trend.

b) The following table gives the no. of defects in alignment observed at the final
inspection of a certain model of an aeroplane, prepare a C-chart and comment on

8
 it.

Aeroplane 01 2 3 4 5 6 7 8 9 10 11 12 13
Number

No. of alignment
07 6 6 7 4 7 8 12 9 9 8 5 5
defect

c) Two machines producing components are checked up for the statistical stability. Draw
the 'P' chart for both machines and comment upon the processes. Sample size for both
machines are 200. 

Machine A:
Sample No. 1 2 3 4 5 6 7 8 9 10

Defectives 25 28 30 30 20 29 31 26 31 27
Machine B:
Sample No. 1 2 3 4 5 6 7 8 9 10

Defectives 11 08 22 15 12 27 10 15 10 02

9
Sample Test Paper I
Paper code:
Roll No.

MSBTE Outcome based Curriculum

Scheme – I
Institute Name:
Programme Name: Mechanical Engineering Programme Code:
Semester: Sixth
Course: Industrial Engineering and Quality Control
Marks: 20 Time: 1 hour
Instructions:All questions are compulsory
1. Illustrate your answers with neat sketches wherever necessary
2. Figures to the right indicate full marks
3. Assume suitable data if necessary
4. Preferably, write the answers in sequential order
Q.1 Attempt any FOUR. (8 Marks)
a) Define anthropometry
b) Define (i) event (ii) activity
c) List recording techniques in method study
d) Define method study and work measurement .
e) Define supply chain management
f) State the functions of process engineer

Q.2 Attempt any THREE. (12 Marks)

a) State the meaning and draw symbol for the following therbligs :
(i) Find (ii) Search (iii)Grasp (iv) Hold
b) Explain production system with block diagram. Also give two examples.
c) Explain the principles of Supply Chain Management
d) State are the factors of production? Explain any two factors of production.
e) Explain the concept of man machine system in ergonomics
f) Explain static dimension and dynamic dimension
g) Draw network, mark critical path and find total project duration.

Activity 1-2 1- 2-4 3- 3-6 4- 5- 6-8 7-8

3 5 6 7
Time in days 10 10 10 20 10 20 20 10 10

10
Sample Test Paper II

Paper code:
Roll No.

MSBTE Outcome based Curriculum

Scheme – I
Institute Name:
Programme Name: Mechanical Engineering Programme Code:
Semester: Sixth
Course: Industrial Engineering and Quality Control
Marks: 20 Time: 1 hour
Instructions:All questions are compulsory
1. Illustrate your answers with neat sketches wherever necessary
2. Figures to the right indicate full marks
3. Assume suitable data if necessary
4. Preferably, write the answers in sequential order
Q.1 Attempt any FOUR. (8 Marks)
a) State the principles of TQM
b) List the types of inspection
c) State the meaning of ISO 9000 and ISO-14000
d) Define cost of quality and value of quality.
e) Define S.Q.C and States its benefit
f) Define median, mode, range and standard deviation
g) Define Quality by Variable and Quality by Attribute

Q.2 Attempt any THREE. (12Marks)

a) Define term Quality. State meaning of term quality of product and quality of services.
b) State merits and demerits of acceptance sampling.
c) Define TQM. Describe any 3 principal elements of TQM.
d) State different types of control charts used in SQC. State the types suitably used for
Quality by Attributes and Quality by Variables.
e) Compare single and double sampling plan

11