Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Mri Shielding: Architectural Site Planning Guide

Download as pdf or txt
Download as pdf or txt
You are on page 1of 34

MRI SHIELDING

ARCHITECTURAL SITE PLANNING GUIDE

Abbott Northwestern Hospital,


Minneapolis, MN

Sept. 2009- Rev. C

400 High Grove Boulevard • Glendale Heights, IL 60139 • (630) 307-7200 Phone • (630) 307-7571 Fax
www.ets-lindgren.com • info@ets-lindgren.com
Table of Contents
Section 1 Introduction

Section 2 MRI Systems

Section 3 Before the Shielding

Section 4 RF Shielding
Section 4.1 RF Flooring
Section 4.2 RF Filters and Waveguides

Section 5 Magnetic Shielding

Section 6 Siting Considerations/Requirements

Section 7 Details

Section 8 Service

Section 9 Accessories
Section 1 Introduction
Magnetic Resonance Imaging (MRI) is a diagnostic imaging tool that uses magnetic fields and radio waves
to generate an image of the patient. It is different from X-ray in that it does not expose the patient to anything
harmful and is a much better tool for soft tissue imaging, whereas X-ray is ideal for hard tissue such as bone.

An MRI is primarily defined by its field strength. For clinical applications, low field magnets are generally less
than 1.5 Tesla while 3.0 Tesla is considered high to very high. Research magnets often range from 0.2 Tesla to
above 20 Tesla.

MRI shielding is also different than X-ray shielding. X-ray requires the use of lead and is more “line-of-sight”
with respect to where the shielding must be positioned. MRI requires radio frequency shielding nearly 100% of
the time with the exception being some small research MR systems. Some of these do not require RF shielding
as they are usually too small to be used for imaging people. MRI can also require magnetic shielding; however,
this is determined on a site-by-site basis.

RF shielding must create a complete box with all walls, ceiling, and flooring covered with an RF shield. The RF
shield can be made of almost any metal, but the most common types of metals are copper, galvanized steel and
aluminum.

What is the purpose of RF shielding? To block out specific radio waves that may distort images created by
the MRI. The specific radio waves may vary based upon the type of MRI installed. As an example, the typical
performance required of an MRI shield is to achieve 100 dB of RF signal attenuation at 100 MHz.

What is the purpose of magnetic shielding? To contain some amount of magnetic field generated by the MRI,
so as not to interfere with surrounding areas. Each site is different as the layout and type of magnet varies.
However, the single most common goal for each MRI site is to contain the 5-gauss field to controlled areas. 5
gauss should not exist in any area where a person may unknowingly walk through the field. Examples include
a waiting room behind or next to an MRI, a service space in the ceiling below the MRI where maintenance
workers may frequent, or an area used for another modality such as PET, where a magnetic field would not be
anticipated.

It should be noted that the 5-gauss limit is a Federal Drug Administration (FDA) recommendation and not law.
The end user must determine what levels of magnetic field are to be contained to which locations.

Page 3 of 34
Philips Open Magnet

Section 2 MRI Systems


Clinical MRI systems are produced by companies such as General Electric Healthcare, Siemens Medical
Solutions, Philips Medical Systems, Hitachi Medical Systems and Toshiba Medical Systems. Others produce
specialized MRI systems such as ONI and Esaote. And, there are those that provide a unique system that utilizes
the MRI produced by one of these companies, but augments it with special features or applications such as
BrainLab or IMRIS.

Some research MRI system manufacturers include Magnex Scientific/Varian Medical, Bruker, and Oxford
Instruments. There are also MRI systems designed specifically for animals. For our purposes, these will be
categorized under research systems to distinguish them from discussions on clinical MRI.

All MRI systems are considered either a closed bore system or an open bore system. A closed bore system is
much like a donut where the patient is moved into the donut hole to be scanned. An open bore system is like a
C-clamp with a gap or slot between two magnet plates. The patient is slid between the plates to be scanned.

The benefit of a closed bore system is that you can typically generate higher field strengths for the magnet.
High-field strength generally means clearer images and shorter scan times or more patients within the normal
workday.

The benefit of an open bore system is that it can accommodate obese patients more easily and allows for a
greater field of view for the patient, which helps alleviate a sense of claustrophobia. An open bore system also
tends to be less costly than a closed bore system, but may not be greater than 1.0 Tesla in field strength and is
often produced at 0.35 Tesla.

Specialty MRI systems are typically extremity scanners. They are designed to accommodate a patient’s arm,
leg, or head. The benefits of an extremity scanner include centrally focusing on a single area of the body and
producing fast, clear images. They are also much less costly than a whole body MRI scanner, but are usually
produced at less than 1.0 Tesla, with a few exceptions.

All MRI systems have their own requirements for shielding, space, acoustics, vibration, power, air conditioning,
and so forth. You should be able to obtain the requirements of your system from your MRI manufacturer.

If you are obtaining a used or refurbished MRI system, you may have difficulty obtaining the same level of
information and/or support from the original equipment manufacturer (OEM). Whoever is providing your
equipment should also provide you with OEM documentation. You can also obtain support from your RF
shielding vendor (see Section 8, Service).

Page 4 of 34
Ferromagnetic Detection
System

Section 3 Before the Shielding


Often overlooked are the things you need to do before RF shielding is installed. Every site should be evaluated
for electromagnetic interference (EMI) and vibration prior to finalization of the site. If your site has excessive
EMI and/or vibration, you may not be able to fully utilize your MRI scanner once it has been installed.

EMI is typically generated by nearby elevators, electrical distribution within the building, nearby car parking
or roads and paths as well as electric trams, subways, etc. The level of EMI can be reduced with shielding;
however, it is minimal. Types of shielding include galvanized steel and aluminum. Silicon steel or low carbon
steel may be helpful, but may require welding or soldering to create the proper eddy current shielding effect
required for EMI.

Shielding is a passive solution to EMI issues, but there are active solutions available such as magnetic active
compensation systems (MACS). These systems measure EMI fluctuations and generate a balancing field, so the
MRI does not notice the EMI. It should be noted that while 85% of all sites can benefit from an active solution,
about 15% may not be solved due to the complex nature of the site. It is critical that an EMI test be conducted
prior to finalizing the location of the MRI.

Vibration testing is often overlooked, but should be conducted on each and every site. New magnet technology
has made magnets lighter and faster, but also more sensitive to vibration. To avoid finding out after you’ve
installed your MRI that your slab needs a vibration pad, schedule a vibration test early to allow modification of
the slab construction, if needed.

Planning for the magnetic field should be done as soon as you have determined what MRI system you will be
acquiring. The 5-gauss zone is a good starting point. Examine where the 5-gauss zone will lie both in plan and
elevation. If it lies outside controlled spaces, than you need to determine if you want to post a sign stating “you
are now entering a magnetic field” or if you want to add magnetic shielding to move the 5-gauss field from the
offending area.

You should also look at the 1-guass field, again both in plan and elevation, to ensure that no sensitive equipment
will lie within that field such as CT scanners, CRT monitors, and so forth. If you cannot move the affected
equipment or reposition the MRI, then you will have to add magnetic shielding or accept the affects of the
magnetic field on the equipment.

Finally, safety should be considered with respect to the MRI suite layout. Is it possible that someone such as
a patient, non-MRI hospital personnel, or visitor could accidentally enter into the MRI scan room? Are there
adequate screening procedures in place to ensure that no accidental magnetic materials will be brought into the
MRI scan room? A Ferrous Metal Detector System (FMDS) can augment the safety and screening procedures at
most MRI sites, but are often overlooked until the project is well underway. Consideration early in the project
allows for planning, evaluation, and inclusion of these products. A single accident can cost significantly more
than the price of an FMDS and is well worth the time and effort to consider it.
Page 5 of 34
Section 4 RF Shielding
RF shielding is required for every clinical MRI system and most research systems. However, performance may
vary based upon the particular MRI system. Always check with your MRI system manufacturer to confirm
specific requirements. Following are general RF shielding sense frequencies:

9.8 MHz.......... 0.23 T 63.9 MHz.......... 1.5 T


12.7 MHz.......... 0.3 T 127.8 MHz.......... 3.0 T
15.0 MHz.......... 0.35 T 200.2 MHz.......... 4.7 T
21.3 MHz.......... 0.5 T 300.0 MHz.......... 7.0 T
42.6 MHz.......... 1.0 T 400.0 MHz.......... 9.4 T

While most MRI manufacturers will require 100 dB of RF attenuation at the sense frequency, the requirements
may vary for any given manufacturer and for higher-frequency testing specifications.

RF shielding can be made of virtually any type of metal; however, the most prominent types used for MRI
shielding are copper, galvanized steel, and aluminum. Other metals are not typically used due to drawbacks
such as price, ease of handling or modifications, and corrosion.

ETS-Lindgren’s copper RF shield is made of copper sheeting wrapped around wood frames bolted together to
form walls and a ceiling. This system is lightweight, easily modified to address field or site discrepancies, and
provides a lasting RF enclosure.

An alternative RF shield system is the cell type, which has a plywood-like core and is laminated on both sides
with galvanized steel, copper or aluminum. This system is heavier and can be modified on site, but with more
effort. In addition, the clamping system, often called “hat and flat,” is ferrous and not recommended by some
MRI systems as it may create shimming problems.

The third type of RF shield system is a pan-form shield constructed entirely of metal. No wood is utilized. This
system is bolted together to form the walls, ceiling and floor. This system can utilize galvanized steel, stainless
steel, or aluminum, depending upon the preference of the MRI system manufacturer. However, this system
cannot be modified on site. Rather, panels must be engineered, manufactured, and shipped tot he site.
Copper Shielding
Cell Type Shielding
Pan Form Shielding

Page 6 of 34
Section 4.1 RF Flooring
There are three basic types of RF flooring: monolithic copper, modular cell type, and pan form.

Monolithic copper requires a normal 1” depression/buildup, is moisture-


resistant, and has a cement-like underlayment as a finish. This is the
recommended RF floor system for MRI applications.

Monolithic Copper
Flooring

The modular cell type floor is a panel system requiring a depression/buildup of


1 1/8” to 1 3/8” with identical construction to that of the cell wall and ceiling
panels. It is a wood core with laminated metal on both sides of the core.
A vapor barrier is placed on the floor to isolate the shield from the ground.
Finished flooring may be installed directly on top of the cell floor panels with
in-fill.
Modular Cell Type
Flooring

The pan-form floor is an all-metal construction with pan-shaped panels bolted together. In-fill of the panels is
required by the customer and is usually done with a concrete underlayment. This system is not recommended if
you have trenches within the MRI suite.

Page 7 of 34
Section 4.2 RF Filters & Waveguides
The RF shield forms a complete box around the MRI system. Everything that is to come into the MRI room
must pass through an RF filter or waveguide.

RF filters are mounted on the RF shield and create an penetration point


for electrical power for lighting or powered outlets within the MRI
room. RF filters also accommodate data cables.

Waveguides are penetrations in the RF shield that allow a fluid flow into
the MRI room. Air conditioning, water and medical gases all provide a fluid
flow and require a waveguide.

To confirm whether an RF filter or waveguide is required, just follow a simple rule of thumb:

1). If there are electrical wires, you will need a filter


2). If it is fluid (air or liquid), you will need a waveguide

Page 8 of 34
Section 5 Magnetic Shielding
Magnetic shielding is not required for every site and is often overlooked in the early planning stages.
Essentially, the goal of magnetic shielding is to protect the environment from the MRI magnetic field.

Magnetic shielding is not the same as lead shielding. Lead shielding is identified via “line of sight” whereas
magnetic shielding must take into account the geometry of the magnetic field relative to the position of the
magnetic shield.

Magnetic shielding is usually fabricated with silicon steel in sheet form,


but it can also be done in steel plate. Steel plate is not as easy to work with
and tends to be more expensive whereas silicon steel is easy to manipulate.
The type of material you will need should be determined by your shield
designer.

Silicon Steel Shielding

Steel Plate Shielding

In most cases, your MRI vendor should be able to provide you with magnetic shield design services. There are
also independent companies who offer it. And, ETS-Lindgren offers magnetic shield design services as well.
You should consider a company that is associated with your shielding vendor. If a design is poorly done, it is all
too easy to finger point. An all-in-one solution is usually the best decision.

Page 9 of 34
Section 6 Siting Considerations / Requirements
There are many facets to take into account when planning an MRI suite. The following are some key items to
consider:
If not, have
• Is the site suitable for the magnet from a vibration standpoint? it tested before
• Is the site suitable for the magnet from an EMI noise standpoint? finalizing the location.
Testing can be done
by either the MRI or
shielding vendor.

________________________________________________________________

•What is the delivery path for the magnet?
•Are the halls wide enough? Are they tall enough?
•Is the floor strong enough?
•Who will rig the magnet?
•Have the riggers evaluated the site as well as the proposed path of
delivery?
•If the magnet has to be removed in the future, will it significantly disrupt
others with the intended exit path?

__________________________________________________________________________________________

Consult the MRI vendor’s Site Planning Specialist with respect to the following:

• Is the site large enough? • Have you examined the proximity of


• Does it meet room size moving metal (i.e., cars trucks,
requirements (length, dumpsters, elevators) and electrical
width, height)? equipment (switchgear and
• Is there adequate air transformers) to the MRI?
conditioning? • Have you considered all possible
• Will it remain at least 65 routes of access for people to
degrees Fahrenheit in the accidentally enter the MRI suite?
MRI room for curing of • Would a ferrous metal detection
floor epoxies? system serve as an effective
• Does the magnetic field supplement to your safety screening
overlap with areas around, process?
above, or below other
equipment that may be disturbed by the MR magnetic field?

You should consider the 1 gauss and 5 gauss lines for most interference Consider where you will place it early in the
concerns. Consider altering the layout first, then magnetic shielding second. layout design for optimal effectiveness.
Page 10 of 34
• Have you considered the sound level of the MRI and will it impact surrounding offices or suites?

Sound can be carried structurally through ducts or vents and even the penetration panel of the MRI
system. Acoustic options for RF shielding consist of sound absorption material within RF panels,
acoustic doors, and an additional layer of glass on RF windows.

Consult your MRI vendor to obtain the acoustic levels of their equipment and then select a Sound
Engineer who can evaluate your entire acoustic situation- not just RF shielding.

ETS-Lindgren has partnered with a professional acoustic engineering company that can conduct a
complete analysis of your acoustic needs.

Acoustic installations take approximately 5-7 days based upon room size and options. Contact your
ETS-Lindgren representative for more information.
__________________________________________________________________________________________

RF Shield Considerations:

Typically, ETS-Lindgren installs the RF shield, closes all temporary openings to run an initial test of the shield,
and, once acceptable, leaves the site. Upon delivery of the magnet, ETS-Lindgren returns to close the access
opening in the RF shield and conducts a final RF test. Your situation may differ, so consult your ETS-Lindgren
representative for your specific requirements.

• What is the proposed delivery path for the RF and/or magnetic installation shielding materials?
• Can these materials fit within the service elevator?
• What is the weight capacity of the service elevator?
• How far is the loading dock from the MRI suite?
• How large and where is the staging area for the shielding materials relative to the MRI suite?
Check with your RF shielding vendor to verify the size of the staging area required, which will vary depending upon the type and
amount of shielding installed.
• Will the staging area be secure from vandalism?
• Will the storage area and MRI suite be protected from the elements (rain, wind, snow, sun)?
• Will the MRI suite be heated during installation?
• Will there be electrical power available for tools?

Page 11 of 34
Section 7 Details
The Enclosure

The preferred RF enclosure for MRI application consists of wood panels wrapped with copper. This provides a
lightweight system that offers the best longevity in RF integrity. The panels are bolted together and to the floor
system.

The alternative consists of metal-wood-metal composite panels. Each panel is clamped to the adjacent panel to
form the entire shield. It is heavier and introduces some amount of ferrous material around the MRI. Consult the
MRI vendor for acceptance of this type of system.

The Floor

The RF floor should be moisture-resistant and consist of copper sheets covered with a cementitious
underlayment ready to accept finished flooring materials (to be installed by another contractor). The RF floor
is a nominal 1” in total depth. For a flush floor finish, a nominal 1” depression is required in the MRI suite.
Alternatively, a 1” rise will require a ramp outside the MRI suite.

The alternative is a composite metal-wood panel system. This is covered with an underlayment material such as
particleboard and ready to accept finished flooring materials.

The RF Door

Although there are many types of RF door systems available, including single swing, double swing, sliding,
double sliding, acoustic, non-acoustic, automatic, and manual, typical doors used for MRI applications are:

ETS-Lindgren MRDS Door- Manual door system with friction seals that require periodic maintenance. Available
in acoustic and non-acoustic.

ETS-Lindgren Auto-Seal II RF Door- Pneumatically-operated door system using hospital air or compressor
air. Smooth edges are perfect for general cleaning and will not snag on clothing or break off. Popular security
options on this door include an automatic opener/closer or keypad entry.

Auto-Seal II Door MRDS Door

Page 12 of 34
Windows

ETS-Lindgren offers the highest-visibility RF view window for the technician sitting at the control console to
monitor and observe the patient. It is an aluminum extruded window with a double layer of mesh sandwiched
between two layers of safety glass. The window can be sized from 2’ x 2’ up to 4’ x 5’. For larger sizes, a
mullion is required.

For skylights or exterior windows, the Clearshield™ RF Window Wall System can be designed to cover an
entire wall from floor to ceiling. With an attractive black matte finish, the window can be used as a future
magnet access path without having to tear out finishes.

Waveguides and Filters

All services for the MRI suite must pass through either a filter or a waveguide. Waveguides used for air supply
to and from the room are honeycomb and can be sized to match the duct running to the MRI suite. Additional
waveguides include those for sinks, medical gas, sprinklers, fiber optics, and plastic or rubber tubing. Finally,
the cryogen vent from superconducting magnets must pass through a cryogen waveguide. The size of the
cryogen waveguide will vary based upon the MRI system. Typically, the MRI vendor will connect the magnet
to the waveguide, but it is the customer or contractor’s responsibility to run the pipe beyond the shield to the
outside of the building.

Filters are primarily used to supply electrical power to the MRI suite. Power for outlets and lighting will require
a separate RF filter for each separate circuit. Filters are also used for nurse call, code blue, telephone, and data.
As each site has its own needs, please contact your ETS-Lindgren representative for the appropriate RF filter for
your particular application.

Architectural Details

The following are standard details that may be obtained from ETS-Lindgren in either AutoCAD format or PDF
for use in the architectural drawing package. Site-specific details will be included in the RF shielding drawing
package. Contact your ETS-Lindgren representative for more information. (Please note the plans reflecting
pages are attached to this Site Planning Guide).

Page 13 of 34
CELL TYPE SHIELD CEILING TO WALL

Page 14 of 34
COPPER SHIELD CEILING TO WALL

Page 15 of 34
AUTO-SEAL II DOOR ELEVATION- INSWING, CELL
TYPE SHIELD, CELL TYPE FLOOR

Page 16 of 34
AUTO-SEAL II DOOR ELEVATION- INSWING, COPPER
SHIELD, CELL TYPE FLOOR

Page 17 of 34
AUTO-SEAL II DOOR ELEVATION- INSWING, COPPER
SHIELD, MONOLITHIC FLOOR

Page 18 of 34
AUTO-SEAL II DOOR ELEVATION- OUTSWING, CELL
TYPE SHIELD, CELL TYPE FLOOR

Page 19 of 34
AUTO-SEAL II DOOR ELEVATION- OUTSWING, COPPER
SHIELD, CELL TYPE FLOOR

Page 20 of 34
AUTO-SEAL II DOOR ELEVATION- OUTSWING, COPPER
SHIELD, MONOLITHIC FLOOR

Page 21 of 34
AUTO-SEAL II DOOR PLAN- INSWING, CELL TYPE
SHIELD

Page 22 of 34
AUTO-SEAL II DOOR ELEVATION- INSWING, COPPER
SHIELD

Page 23 of 34
AUTO-SEAL II DOOR PLAN- OUTSWING, CELL TYPE
SHIELD

Page 24 of 34
AUTO-SEAL II DOOR PLAN- OUTSWING, COPPER TYPE
SHIELD

Page 25 of 34
FLOOR TO WALL- CELL TYPE SHIELD, CELL TYPE
FLOOR

Page 26 of 34
FLOOR TO WALL- COPPER SHIELD, CELL TYPE FLOOR

Page 27 of 34
FLOOR TO WALL- CELL TYPE SHIELD, MONOLITHIC
FLOOR

Page 28 of 34
FLOOR TO WALL- COPPER SHIELD, MONOLITHIC
FLOOR

Page 29 of 34
MEDICAL GAS WAVEGUIDE

Page 30 of 34
RF ELECTRICAL POWER FILTER

Page 31 of 34
SPRINKLER WAVEGUIDE

Page 32 of 34
Section 8 Service
The number of used MRIs being sold and the number of sites replacing or upgrading old MRIs is growing
dramatically. In addition, hospitals are striving to make their existing MRIs function longer, thereby delaying
replacement. All of these actions necessitate the need for service.

ETS-Lindgren offers service contracts ranging from 1 to 5 years and also responds to as-needed service calls as
well. With a dedicated Service Department consisting of 10 experienced and skilled personnel, ETS-Lindgren
can respond to any problem on any RF shielding, including non-ETS-Lindgren shields.
Air Gap

Services include, but are not limited to:


Deck, Parent Ceiling
RF Panel w/ Sound Insulation Fill
Ceiling Support
Acoustic Tile Drop Ceiling
Copper Shield

• RF Testing / Troubleshooting
• EMI (moving metal) Testing
• Vibration Testing
• Design Assistance
• RF Shield Repair 3” Air Gap

Copper Shield

• RF Shield Upgrade and/or Modification RF Panel w/


Sound Insulation Fill

• Engineering & Consultation 3 5/8 in. Stud

5/8 in. layer Drywall

*Magnetic Shield Design Underlayment

*Acoustic & Vibration consulting Copper Shield


Epoxy Adhesive

*RF consulting Epoxy Isolator

Parent Floor

Acoustic Design Assistance

__________________________________________________________________________________________

Contact your ETS-Lindgren representative or call our

Service Department at

(630) 912-1900

Page 33 of 34
Section 9 Accessories
ETS-Lindgren is more than an RF shielding company. By offering a comprehensive line of accessories for the
MRI suite, we can be your single source for a number of products and services.

LED Lighting

LED downlights serve as an excellent light source in the MRI suite and never have to be replaced. This elimi-
nates the need for maintenance workers to replace bulbs within the MRI suite, which reduces the risk of ferrous
tools being introduced into the suite and accidentally pulled into the MRI.

LED Graphic Panel Display

Envision any image you would like to display in your MRI suite and then backlight it with LEDs. This type of
presentation helps create a soothing, relaxed environment for the patient. Whether you desire a ceiling or wall-
mount, ETS-Lindgren offers a system and size to suit your needs.

Magnetic Active Compensation System (MACS)

MACS is designed to protect the MRI from environmental disturbances caused by trains, cars, elevators, etc.
and resolves EMI disturbance in 90% of cases. It can be installed in conjunction with the RF shield or after.
Evaluate your need for a MACS by arranging for EMI testing.

Closed Circuit TV (CCTV) Intercom System

CCTV is an affordable audio and/or video communication system for the MRI suite that is also easy to install. It
increases your monitoring ability as well as communication with the patient.

Ferromagnetic Detection System (FMDS)

FMDS is an additional safety precaution that helps screen patients and hospital staff for ferrous objects prior
to entering the MRI suite. Equipped with color-coded lighting and an auditory alert, you are made aware both
before and as you pass the FMDS that you are at risk for causing an accident. Recommended by the American
College of Radiology, ferromagnetic detectors are a tremendous addition to your existing safety and screening
program.

Page 34 of 34

You might also like