Ultrasonic Testing

Materials Testing
Dr. Belal Gharaibeh
JU

1
• Ultrasonic Testing (UT) uses high frequency
sound waves (typically in the range between
0.5 and 15 MHz) to conduct examinations and
make measurements. Besides its wide use in
engineering applications (such as flaw
detection/evaluation, dimensional
measurements, material characterization,
etc.), ultrasonics are also used in the medical
field (such as sonography, therapeutic
ultrasound, etc.).

2
• In general, ultrasonic testing is based on the
capture and quantification of either the
reflected waves (pulse-echo) or the
transmitted waves (through-transmission).
• Each of the two types is used in certain
applications, but generally, pulse echo systems
are more useful since they require one-sided
access to the object being inspected.

3
 Basic Principles
• A typical pulse-echo UT inspection system consists of
several functional units, such as the pulser/receiver,
transducer, and a display device. A pulser/receiver is an
electronic device that can produce high voltage electrical
pulses. Driven by the pulser, the transducer generates
high frequency ultrasonic energy.

4
 Basic Principles
• The sound energy is introduced and propagates
through the materials in the form of waves.
• When there is a discontinuity (such as a crack) in
the wave path, part of the energy will be reflected
back from the flaw surface.
• The reflected wave signal is transformed into an
electrical signal by the transducer and is
displayed on a screen. Knowing the velocity of
the waves, travel time can be directly related to
the distance that the signal traveled.
• From the signal, information about the reflector
location, size, orientation and other features can
sometimes be gained. 5
 Advantages
• It is sensitive to both surface and subsurface
discontinuities.
• The depth of penetration for flaw detection or
measurement is superior to other NDT methods.
• Only single-sided access is needed when the pulse-echo
technique is used.
• It is highly accurate in determining reflector position and
estimating size and shape.
• Minimal part preparation is required.
• It provides instantaneous results.
• Detailed images can be produced with automated systems.
• It is nonhazardous to operators or nearby personnel and
does not affect the material being tested.
• It has other uses, such as thickness measurement, in
addition to flaw detection.
• Its equipment can be highly portable or highly automated.
6
 Disadvantages
• Surface must be accessible to transmit ultrasound.
• Skill and training is more extensive than with some other
methods.
• It normally requires a coupling medium to promote the
transfer of sound energy into the test specimen.
• Materials that are rough, irregular in shape, very small,
exceptionally thin or not homogeneous are difficult to
inspect.
• Cast iron and other coarse grained materials are difficult to
inspect due to low sound transmission and high signal
noise.
• Linear defects oriented parallel to the sound beam may go
undetected.
• Reference standards are required for both equipment
calibration and the characterization of flaws. 7
 Wave propagation
• Ultrasonic testing is based on the vibration in
materials which is generally referred to as
acoustics. All material substances are comprised of
atoms, which may be forced into vibrational
motion about their equilibrium positions.
• Many different patterns of vibrational motion exist
at the atomic level; however, most are irrelevant to
acoustics and ultrasonic testing. Acoustics is
focused on particles that contain many atoms that
move in harmony to produce a mechanical wave.
•

8
• When a material is not stressed in tension or
compression beyond its elastic limit, its individual
particles perform elastic oscillations. When the
particles of a medium are displaced from their
equilibrium positions, internal restoration forces
arise.
• These elastic restoring forces between particles,
combined with inertia of the particles, lead to the
oscillatory motions of the medium.
9
• In solids, sound waves can propagate in four
principal modes that are based on the way the
particles oscillate. Sound can propagate as
longitudinal waves, shear waves, surface
waves, and in thin materials as plate waves.
Longitudinal and shear waves are the two
modes of propagation most widely used in
ultrasonic testing.

10
 Properties of Acoustic Waves
• Among the properties of waves propagating in
isotropic solid materials are wavelength,
frequency, and velocity. The wavelength is
directly proportional to the velocity of the
wave and inversely proportional to the
frequency of the wave. This relationship is
shown by the following equation:

11
• The velocity of sound waves in a certain medium
is fixed where it is a characteristic of that
medium.
• As can be noted from the equation, an increase in
frequency will result in a decrease in wavelength.
• For instance, the velocity of longitudinal waves in
steel is 5850 m/s and that results in a wavelength
of 5.85 mm when the frequency is 1 MHz.

12
Wavelength and Defect Detection
• In ultrasonic testing, the inspector must make a
decision about the frequency of the transducer
that will be used in order to control the
wavelength.
• The wavelength of the ultrasound used has a
significant effect on the probability of detecting a
discontinuity.
• A general rule of thumb is that a discontinuity
must be larger than one-half the wavelength to
stand a reasonable chance of being detected.
13
 Sensitivity and resolution factors
• Sensitivity and resolution are two terms that are
often used in ultrasonic inspection to describe a
technique's ability to locate flaws.
• Sensitivity is the ability to locate small
discontinuities. Sensitivity generally increases
with higher frequency (shorter wavelengths).
• Resolution is the ability of the system to locate
discontinuities that are close together within the
material or located near the part surface.
• Resolution also generally increases as the
frequency increases.
14
 wave frequency factor
• The wave frequency can also affect the capability
of an inspection in adverse ways. Therefore,
selecting the optimal inspection frequency often
involves maintaining a balance between the
favorable and unfavorable results of the
selection.
• Before selecting an inspection frequency, the
material's grain structure and thickness, and the
discontinuity's type, size, and probable location
should be considered

15
• As frequency increases, sound tends to scatter
from large or course grain structure and from
small imperfections within a material.
• Cast materials often have coarse grains and
thus require lower frequencies to be used for
evaluations of these products.
• Wrought and forged products with directional
and refined grain structure can usually be
inspected with higher frequency transducers.

16
• Since more things in a material are likely to
scatter a portion of the sound energy at higher
frequencies, the penetration depth (the
maximum depth in a material that flaws can be
located) is also reduced.
• Frequency also has an effect on the shape of the
ultrasonic beam. Beam spread, or the divergence
of the beam from the center axis of the
transducer, and how it is affected by frequency
will be discussed later.

17
 Sound Propagation in Elastic
Materials
• sound waves propagate due to the vibrations or
oscillatory motions of particles within a material.
• An ultrasonic wave may be visualized as an
infinite number of oscillating masses or particles
connected by means of elastic springs.
• Each individual particle is influenced by the
motion of its nearest neighbor and both inertial
and elastic restoring forces act upon each particle

18
• A mass on a spring has a single resonant
frequency (natural frequency) determined by its
spring constant k and its mass m.
• Within the elastic limit of any material, there is a
linear relationship between the displacement of a
particle and the force attempting to restore the
particle to its equilibrium position.
• This linear dependency is described by Hooke's
Law. In terms of the spring model, the relation
between force and displacement is written as F =
k x.

19
 The Speed of Sound
• Hooke's Law, when used along with Newton's Second
Law, can explain a few things about the speed of
sound. The speed of sound within a material is a
function of the properties of the material and is
independent of the amplitude of the sound wave.
• Newton's Second Law says that the force applied to a
particle will be balanced by the particle's mass and the
acceleration of the particle. Mathematically, Newton's
Second Law is written as F = m a.
• Hooke's Law then says that this force will be balanced
by a force in the opposite direction that is dependent
on the amount of displacement and the spring
constant. Therefore, since the applied force and the
restoring force are equal, m a = k x can be written 20
• Since the mass m and the spring constant k are
constants for any given material, it can be seen that the
acceleration a and the displacement x are the only
variables.
• It can also be seen that they are directly proportional.
For instance, if the displacement of the particle
increases, so does its acceleration.
• It turns out that the time that it takes a particle to
move and return to its equilibrium position is
independent of the force applied.
• So, within a given material, sound always travels at the
same speed no matter how much force is applied when
other variables, such as temperature, are held
constant.
21
 Material Properties Affecting the Speed of Sound
• Of course, sound does travel at different speeds
in different materials. This is because the mass of
the atomic particles and the spring constants are
different for different materials.
• The mass of the particles is related to the density
of the material, and the spring constant is related
to the elastic constants of a material.
• The general relationship between the speed of
sound in a solid and its density and elastic
constants is given by the following equation:

22
• This equation may take a number of different
forms depending on the type of wave
(longitudinal or shear) and which of the elastic
constants that are used.
• It must also be mentioned that the subscript
“ij ” attached to “ C” in the above equation is
used to indicate the directionality of the elastic
constants with respect to the wave type and
direction of wave travel

23
• In isotropic materials, the elastic constants are
the same for all directions within the material.
However, most materials are anisotropic and the
elastic constants differ with each direction.
• For example, in a piece of rolled aluminum plate,
the grains are elongated in one direction and
compressed in the others and the elastic
constants for the longitudinal direction differs
slightly from those for the transverse or short
transverse directions.

24
• For longitudinal waves, the speed of sound in
a solid material can be found as:

25
• While for shear (transverse) waves, the speed
of sound is found as:

26
 Attenuation of Sound Waves
• When sound travels through a medium, its
intensity diminishes with distance. In idealized
materials, sound pressure (signal amplitude) is
reduced due to the spreading of the wave.
• In natural materials, however, the sound
amplitude is further weakened due to the
scattering and absorption.

27
 Scattering
• Scattering is the reflection of the sound in
directions other than its original direction of
propagation.
• Absorption is the conversion of the sound
energy to other forms of energy.
• The combined effect of scattering and
absorption is called attenuation.
• Attenuation is generally proportional to the
square of sound frequency.
28
• The amplitude change of a decaying plane
wave can be expressed as:

29
30
 Acoustic Impedance
• Sound travels through materials under the
influence of sound pressure.
• Because molecules or atoms of a solid are
bound elastically to one another, the excess
pressure results in a wave propagating
through the solid.
• The acoustic impedance ( Z) of a material is
defined as the product of its density ( ρ) and
the velocity of sound in that material (V ).

31
32
• Acoustic impedance is important in:
• the determination of acoustic transmission
and reflection at the boundary of two
materials having different acoustic
impedances.
• the design of ultrasonic transducers.
• assessing absorption of sound in a medium.

33
 Reflection and Transmission Coefficients

• Ultrasonic waves are reflected at boundaries

34
• The fraction of the incident wave intensity that is
reflected can be derived based on the fact that
particle velocity and local particle pressures must
be continuous across the boundary.
• When the acoustic impedances of the materials
on both sides of the boundary are known, the
fraction of the incident wave intensity that is
reflected (the reflection coefficient) can be
calculated as:

35
• Since the amount of reflected energy plus the
transmitted energy must equal the total
amount of incident energy, the “transmission
coefficient” is calculated by simply subtracting
the reflection coefficient from one (T=1-R)

36
• Taking for example a water steel interface and calculating
the reflection and transmission coefficients (using the
acoustic impedance information given in the previous
table), we get = 0.88 and = 0.12.
• This means that the amount of energy transmitted into the
second material is only 12% while 88% is reflected back at
the interface.
• If we convert the amounts of reflection and transmission to
decibels, we find that to be -1.1 dB and -18.4 dB
respectively.
• The negative sign indicates that individually, the amount of
reflected and transmitted energy is smaller than the
incident energy.

37