Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

MXFNX2 Booklet Finisher PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 116

SERVICE MANUAL

CODE: 00ZMXFNX2/S1E

DIGITAL FULL COLOR


MULTIFUNCTIONAL SYSTEM OPTION
SADDLE STITCH FINISHER
PUNCH MODULE
PAPER PASS UNIT

MX-FNX2
AR-PN1A/B/C/D
MODEL MX-RBX1
CONTENTS

[1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1


[2] SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[3] UNPACKING AND INSTALLATION
* For how to unpacking and installation, refer to the installation manual (00ZMX2700/I1E).

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . . 4-1


[5] OPERATIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6] DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[7] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[8] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[9] SELF DIAG MESSAGE AND TROUBLE CODE . . . . . . . . . . . . . . . 9-1
[10] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
„ PARTS GUIDE

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used


SHARP CORPORATION for after sales service only.
The contents are subject to change without notice.
CONTENTS

[1] PRODUCT OUTLINE [6] DISASSEMBLY AND ASSEMBLY


1. Product outline. . . . . . . . . . . . . . . . . . . . .1-1 1. Saddle stitch finiser (MX-FNX2) . . . . . . 6-1
2. Configuration . . . . . . . . . . . . . . . . . . . . . .1-1 2. Paper Transport Section (MX-RBX1) . . 6-11
3. Punch Unit (AR-PN1A/B/C/D) . . . . . . 6-14
[2] SPECIFICATIONS
1. MX-FNX2 . . . . . . . . . . . . . . . . . . . . . . . . .2-1 [7] MAINTENANCE
2. AR-PN1A/B/C/D. . . . . . . . . . . . . . . . . . . .2-2 1. Maintenance System Table . . . . . . . . . 7-1
3. MX-RBX1. . . . . . . . . . . . . . . . . . . . . . . . .2-2
[8] ADJUSTMENTS
[3] UNPACKING AND INSTALLATION 1. Finisher/saddle unit . . . . . . . . . . . . . . . 8-1
* For how to unpacking and installation, refer to the 2. Punch unit (option) . . . . . . . . . . . . . . . . 8-1
installation manual (00ZMX2700/I1E).
[9] SELF DIAG MESSAGE AND TROUBLE CODE
[4] EXTERNAL VIEWS AND INTERNAL
STRUCTURES 1. Self diag message . . . . . . . . . . . . . . . . 9-1

1. Part names and functions . . . . . . . . . . . .4-1 2. Trouble code . . . . . . . . . . . . . . . . . . . . 9-1

[5] OPERATIONAL DESCRIPTION [10] ELECTRICAL SECTION

1. Basic operations . . . . . . . . . . . . . . . . . . .5-1 1. Block diagram. . . . . . . . . . . . . . . . . . . 10-1

2. Feed/Drive System . . . . . . . . . . . . . . . . .5-4 2. Wiring diagram . . . . . . . . . . . . . . . . . . 10-3

3. Stapling Operation . . . . . . . . . . . . . . . . . .5-7 3. LEDs and Check Pins by PCB . . . . . . 10-8

4. Delivery Tray Operation . . . . . . . . . . . . .5-10 „ PARTS GUIDE


5. Saddle Unit . . . . . . . . . . . . . . . . . . . . . .5-10
[1] PRODUCT OUTLINE
âºíuÇ´
Service Manual

1. Product outline
This unit is installed to the following machines to perform the after-process of output paper from a copier, or a fax machine. The output paper is
passed to the saddle finisher by the interface unit (MX-RBX1). Each sheet is discharged one by one by the offset function.
1) Employment of the through-type stapler: Employment of the through-type stapler allows to make saddle stitch by one stapler.
2) 3 kinds of auto staple functions:
There are 3 staple positions available. (One position in the front, one position at the back, 2 positions at the center)
3) Saddle stitch function: Up to 10 sheets of paper can be stapled at the center and folded into two and discharged.
4) Punch function (Option):
By installation of a puncher unit, paper can be punched to make holes for a binder. (Applicable for 64 – 128g/m 2. OHP films cannot be
used.)

Applicable models MX-2300N/2700N/2300G/2700G

The finisher requires staple cartridge as a consumable part. (Staple cartridge (About 5000 staples x 3) AR-SC2)

2. Configuration
1) When installing this unit, the paper feed desk (MX-DEX1/DEX2) and the interface unit (MX-RBX1) must be installed together.
2) This unit cannot be installed with the finisher (MX-FNX1) simultaneously.

Device Tray with


Staple cartridge USB Hub (MX-RKX1) Reversing single pass feeder
(Approx. 5000 x 3) (MX-RPX1)
(MX-SCX1) Finisher
(MX-FNX1)
PCL5c/PCL6 Network SPLC-c
driver scanner driver
(Sharpdesk 1 license)

Document cover
RSPF (MX-VRX1)
Punch module
● 2-hole (MX-PNX1A)

● 3-hole (MX-PNX1B)

● 4-hole (MX-PNX1C)

● 4-hole (broad space)

(MX-PNX1D) HDD
HDD Exit tray unit
Paper pass unit (MX-TRX1)
(MX-RBX1)
Copier/Printer (PCL) Copier/Printer (SPLC-c)
/Scanner model model
Staple cartridge (MX-2300N) (MX-2300G)
(Approx. 5000 x 3)
(AR-SC2)
(MX-2700N) (MX-2700G)

Punch module
● 2-hole (AR-PN1A) Saddle stitch finisher Stand/1x500 sheet Stand/2x500 sheet Large capacity tray
● 3-hole (AR-PN1B) (MX-FNX2) paper drawer paper drawer (MX-LCX1)
● 4-hole (AR-PN1C) (MX-DEX1) (MX-DEX2)
● 4-hole (broad space)

(AR-PN1D) Printer expansion Network scanner PS3 expansion


Barcode font kit Facsimile
kit (PCL) expansion kit kit
expansion kit
(MX-FXX1)
CD ROM
CD CD CD ROM
(AR-PF1)
(MX-PBX1) (MX-NSX1) FAX memory (8MB)
Data security kit (For MX-2300G/2700G) (MX-PKX1) (packed together)
(Including document control)
CC authentication Commercial Internet Fax Sharpdesk Sharpdesk
version version expansion kit 1 license kit 10 license kit
Sharpdesk Sharpdesk
5 license kit 50 license kit
Security Security
ROM ROM
CD CD CD
(MX-USX1/ (MX-US10/
(MX-FWX1) USX5) US50)
For document For document
control PWB control PWB Application Sharpdesk Application External
integration 100 license kit communication account module
(MX-FRX1) (MX-FRX1U) module module

256MB expansion memory board


(MX-SMX1)
CD CD CD CD

(For MX-2300G/2700G) (MX-AMX1) (MX-USA0) (MX-AMX2) (MX-AMX3)

MX-FNX2/AR-PN1/MX-RBX1 PRODUCT OUTLINE 1 – 1


[2]
âºíuÇ´
SPECIFICATIONS Service Manual

1. MX-FNX2
A. Basic specifications
Type Console type finisher
Loading method Ascending offset tray
Transport speed 23/27/35/45 ppm
Transport reference Center reference
Mode types Non-staple, staple
Paper sizes allowed for offset A3, B4, A4, A4R, B5, B5R, 8K, 16K, 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R
Offset quantity 20mm, 0.8 inch
Tray type (Number of trays) Upper tray: Lift-up/down offset tray
Lower tray: Book tray for saddle stitch
Paper exit direction Face down
Paper exit paper size A3W, A3, B4, A4, A4R, B5, B5R, A5R, 16K, 16KR
12" x 18", 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5"R, 7.25" x 10.5"R
Power consumption 52W
Power source Supplied from the host machine power (DC24V/DC5V)
External dimensions (W x D x H) When the paper exit tray is on the storge position: 555 x 610 x 1010 (mm), 21 27/32 x 24 1/64 x 39 49/64 (inch)
When the paper exit tray is on the pull-out position: 665 x 610 x 1050 (mm), 26 11/64 x 24 1/64 x 41 21/64 (inch)
Occupying dimensions (W x D) When the tray is on pull-out position: 665 x 610 (mm), 21 27/32 x 24 1/64 (inch)
* Distance from the main unit: 300mm, 11 13/16 inch
Weight Approx. 46kg (101.4 lbs)
Installation/maintenance Installed by service personnel
Optional detection Auto detection supported
Packaged items Parts for mounting, operational sheet, staple directional instruction label, punch directional instrucrtion label,
installation cautionary note

B. Finishing section
Capacity of paper exit and load Non-staple: 1,000 sheets (Small size) Max. 500 sheets for A5R, INV-R (Plain paper 60 to 80g/m2 (16 to 21 lbs)
or equivalent)
500 sheets (Large size) (Plain paper 60 to 80g/m2 (16 to 21 lbs) or equivalent)
Staple sort: 30 sets * (Max. 50 sets for small size, one-position stapling at the rear)
Max: 1,000 sheets (Small size)
500 sheets (Large size)
*: Less than 1,000 sheets and less than 30 sets depending on the use environment and paper curl.
Large size: A3W, A3, B4, 8K, 12" x 18", 11" x 17", 8.5" x 14", 8.5" x 13"
Small size: A4, A4R, B5, B5R, A5R, 16K, 16KR, 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5"R, 7.25" x 10.5"R
Offset function Provided
Paper size which can be stapled A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR, 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R
Ejectable paper size Determinate AB type A3W, A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR
size Inch type 12" x 18", 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5"R,
7.25" x 10.5"R
Indeterminate AB type 148 x 100 to 432 x 297
size Inch type 5 1/2" x 5 1/2" to 17" x 11 5/8"
Paper weight Thin paper: 55 to 59g/m2 (15 to 16 lbs)
Plain paper: 60 to 105g/m2 (16 to 28 lbs)
Heavy paper: 106 to 209g/m2 (28 to 56 lbs)
Quantity of paper to be stapled (Max.) 30 sheets (Small size, 90g/m2 (24 lbs))
25 sheets (Large size, 90g/m2 (24 lbs))
Stapling 3 kinds (One in the front, one at the back, two positions)
Staple supply Staple cartridge replacement
Staple detection Staple empty detection: Provided (Nearly empty: 40 pcs. remained)
Manual stapling No

C. Saddle stitch section


Stapling type Common to the staple specifications. 2-position stapling (center stapling), face down
Folding location Center folding
Paper size A3, B4, A4R, 8K, 16KR, 11" x 17", 8.5" x 11"R
Weight of paper applicable for saddle stitch 55 to 209g/m2 (15 to 56 lbs)
Quantity of paper to be stapled 10 sets (6 to 10 sheets), 20 sets (1 to 5 sheets)

D. Consumable parts
Name Content Life Product name
Staple cartridge Staple cartridge x 3 5000 x 3 AR-SC2

MX-FNX2/AR-PN1/MX-RBX1 SPECIFICATIONS 2 – 1
2. AR-PN1A/B/C/D
Type Punch unit for saddle finisher
Punch type 2 holes / 3 holes / 4 holes / 4 holes (wide)
A punch unit that provides all of these 4 types can be installed.
Transport speed 23, 27, 35, 45, sheets/min.
Transport reference Center reference
Punch dust full detection Provided
Paper exit direction Face down
Paper weight Plain paper: 60 to 105g/m2 (16 to 28 lbs)
Thin paper: 55 to 59g/m2 (15 to 16 lbs)
Heavy paper: 106 to 209g/m2 (28 to 56 lbs)
Puchable paper size 2 holes A3, B4, A4, A4R, B5, B5R, 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 8K, 16K, 16KR
(AR-PN1A)
3 holes *1 3 holes: A3, A4, 11" x 17", 8.5" x 11"
(AR-PN1B) 2 holes: 8.5" x 14", 8.5" x 13", 8.5" x 11"R
4 holes A3, A4
(AR-PN1C)
4 holes (wide) A3, B4, A4, A4R, B5, B5R, 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R
(AR-PN1D)
Power source Supplied from the finisher
External dimensions (W x D x H) 105 x 560 x 175 (mm), 4 9/64 x 22 3/64 x 6 57/64 (inch)
Weight Approx. 2.9kg (6.4 lbs)
Packaged items Parts for mounting, instructional label for garbage pickup

*1: Auto switching: 2 holes/3 holes


Kind of hole punch

Hole Hole
Kind Hole position Kind Hole position
size size
2 holes A: 80±1mm φ6.5mm 4 holes A: 80±1mm φ6.5mm
(AR-PN1A) B: 12±3mm (AR-PN1C) B: 12±3mm

A A A A

B B

3 holes A: 108±1mm φ8.0mm 4 holes A: 70±1mm φ6.5mm


(AR-PN1B) B: 12±3mm (wide) B: 12±3mm
(AR-PN1D) C: 21±1mm

A A A C

B B

3. MX-RBX1
Type Paper pass unit
Paper reception reference Center referance
Receiving speed 62 to 450mm/sec (23 to 45cpm)
Receiving and sending speed 23 to 45cpm
Paper weight Thin paper: 55 to 59g/m2 (15 to 16 lbs)
Plain paper: 60 to 105g/m2 (16 to 28 lbs)
Heavy paper: 106 to 209g/m2 (28 to 56 lbs)
Transportable paper sizes A3W, A3, B4, A4, A4R, B5, B5R, A5R, 16K, 16KR
12" x 18", 11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11", 8.5" x 11"R, 5.5" x 8.5"R, 7.25" x 10.5"R
External dimensions (W x D x H) 555 x 535 x 165 (mm), 21 27/32 x 21 1/16 x 6 1/2 (inch)
Weight Approx. 7kg (15.4 lbs)
Power source Supplied by saddle finisher
Power consumption Included with saddle finisher power consumption
Interface Mechanical: Fixed to the main unit with screws.
Electrical: Cable connection from the finisher
Control: Controlled by the communication command from the main unit through the finisher.
Installation/maintenance Installed by service personnel
Optional detection Auto detection supported
Packaged items Parts for mounting, installation cautionary note

MX-FNX2/AR-PN1/MX-RBX1 SPECIFICATIONS 2 – 2
[4] EXTERNAL VIEWS AND INTERNAL Service
âºíuÇ´
STRUCTURES
Manual

1. Part names and functions


A. External view

1 2

3
6

5
4

1 Staple compiler 4 Front cover


2 Top cover 5 Saddle stitch tray
3 Staple section 6 Offset tray

B. Internal structure
(1) Finisher section

1 2 3 4 5 6 7

8 9 10 11 12 13 14 15 16 17

1 Paper exit tray 10 Stapler


2 Alignment plate (Front, back) 11 Saddle section
3 Paddle 12 Book making stopper
4 Paper exit roller 13 Book making tray
5 Process tray stopper 14 Bundle transport roller
6 Transport roller 15 Book making exit roller
7 Punch section (Option) 16 Paper folding roller
8 Paper exit belt 17 Paper pushing plate
9 Bundle exit roller

MX-FNX2/AR-PN1/MX-RBX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 1


(2) Punch section (Option: AR-PN1A/B/C/D)

1 2 3 4

1 Die 3 Punch
2 Cam 4 Punch dust box

(3) Interface transport section (MX-RBX1)

1 2 3 4 9

5 6 7 8 10

1 Paper exit roller 6 Paper exit front roller


2 Paper exit front roller 7 Inlet port rear roller
3 Inlet port rear roller shaft 8 Inlet port roller
4 Inlet port roller 9 Reverse flapper
5 Paper exit roller 10 Upper guide flapper

MX-FNX2/AR-PN1/MX-RBX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 2


C. Finisher and saddle section
(1) Sensor, switch and clutch

15
26
5 3
14
2 1
28
23 12
16 7
4 25 6 27
24 17 8 11
22 9
13 10
19
20
21
18

No. Signal Name Active condition


1 FED Entry paper sensor Paper detected: "H"
2 FPDHPD Paddle home position sensor Paddle HP: "H"
3 FARHPD Bundle roller home position sensor Oscillation guide HP: "H"
4 FFJHPD Alignment home position sensor (front) Alignment tray (F) HP: "H"
5 FRJHPD Alignment home position sensor (rear) Alignment tray (R) HP: "H"
6 FAD Alignment tray sensor Paper detected: "H"
7 FOBHPD Exit belt home position sensor Paper exit belt HP: "H"
8 FBED Tray paper sensor Tray paper detected: "H"
9 FSLD Paper level sensor Paper detected: "H"
10 FFPD Bookbinding position sensor Paper detected: "L"
11 FFHPD Bookbinding home position sensor Folding operation HP: "L"
12 FFRHPD Bookbinding roller home position sensor Bundle transport roller HP: "H"
13 FFED Bookbinding paper sensor Paper detected: "H"
14 FFE Bookbinding lock sensor
15 FULD Lift upper sensor Tray upper limit detected: "H"
16 FLLD Lift lower sensor Tray lower limit detected: "H"
17 FLE Lift lock sensor
18 FSTHPD Staple shift home position sensor Stapler HP: "H"
19 FSHPD Staple drive home position sensor Stapler stapling HP: "L"
20 FSPD Self prime sensor Cartridge staple detected: "L"
21 FSD Staple empty sensor Stapler cartridge detected: "L"
22 FFDD Front door sensor Front cover open: "H"
23 FCD Upper cover sensor Upper cover open: "H"
24 FFDDW Front door switch Front door closed: "H"
25 FJSW Joint switch Printer connected: "H"
26 FSSSW Staple safety switch Oscillation guide closed: "H"
27 FCC Bookbinding clutch When drive is transmitted: "H"
28 FMLD Tray middle sensor Tray middle detected: "H"

MX-FNX2/AR-PN1/MX-RBX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 3


(2) Motor and PCB

2 1
7
5
8
4
3

9
6

No. Signal Name Active condition


1 FFM Transport motor Paper transport
2 FPM Paddle motor Oscillation guide drive, paper exit to offset tray
3 FAM Bundle exit motor Paper exit operation
4 FFJM Alignment motor (front) Alignment plate (F) drive
5 FRJM Alignment motor (rear) Alignment plate (R) drive
6 FLM Lift motor Paper exit tray up/down
7 FFSM Staple motor Stapling/paper folding
8 FSM Staple shift motor Staple unit sliding
9 PBA-CONT Control PCB Finisher control

D. Interface transport section (MX-RBX1)

1
4
3
6

No. Signal Name Type Function/Operation Output


1 FJPID Interface transport unit inlet port sensor Photointerrupter Interface inlet port paper detection LO light is interrupted
when paper is provided.
2 FJPOD Interface transport unit outlet port Photointerrupter Interface outlet port paper detection LO light is interrupted
sensor when paper is provided.
3 FJPDD Interface transport unit cover sensor Photointerrupter Interface cover open detection Light is interrupted when
the cover is open.
4 FJPM Interface transport motor Paper transport roller drive
5 FINRPS Interface reverse path solenoid Drive of the flapper which selects the path in
the finisher and the reverse path
6 FJFM Interface fan Temperature rise protection fan in the
finisher inlet port section

MX-FNX2/AR-PN1/MX-RBX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 4


E. Punch section (AR-PN1A/B/C/D)
(1) Sensor

3
1
2

No. Signal Name Active condition


1 FPHPD Punch home position sensor Punch HP detected: "L"
2 FPSHPD Punch side resist home position sensor Punch slide unit HP detected: "H"
3 FPMCK Punch motor lock sensor

(2) Motor and PCB

3
1

4 2
5

No. Signal Name Active condition


1 FPNM Punch motor Punch drive
2 FPSM Punch side resist motor Punch slide unit transverse move
3 Punch control PCB
4 FPTD Side resist photo sensor PCB Punch horizontal resist and punch timing detection
5 FPSD1 – 4 Side resist LED PCB
6 FPDD Dust full photo sensor PCB Punch dust full detection
7 Dust full LED PCB

MX-FNX2/AR-PN1/MX-RBX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 5


[5]
âºíuÇ´
OPERATIONAL DESCRIPTION B. OutlineManual
Service of the Electrical Circuitry
The sequence of finisher operations is controlled by the finisher
controller PCB. The finisher controller PCB is a 16-bit microproces-
1. Basic operations sor (CPU), and is also used for combination with the host machine
(serial).
A. Specifications
The finisher controller PCB drive motors and other loads in
The finisher serves to deliver sheets coming from its host machine.
response to the various commands from the host machine. It also
The mode of delivery may be non-sort stack, job offset *, or staple
communicates such data as on the states of various sensors and
delivery.
switches to the host machine by way of the serial communication
The saddle unit built into the finisher is used to fold a stack of line.
sheets coming from the finisher unit in half for delivery.
The ICs mounted to the finisher controller PCB have the following
The punch unit (option) is designed for installation to the pickup functions:
assembly of the finisher, and is used to punch holes in sheets com-
• IC13 (CPU): Controls sequence of operations.
ing from the host machine.
• IC12 (EEP-ROM): Backs up adjustment settings.
The above operations are controlled with various commands from
the finisher controller PCB as well as the commands from the • IC6: Stores sequence programs.
punch controller PCB. • IC11 (expansion port): I/O port
The flow of signals between finisher and options controller is shown
as below.
Punch unit drive
system (punch unit; Finisher unit
option)
Host machine DC
Finisher controller PCB
Alignment drive system CPU
controller
PCB Motor
Control system

Stapler drive system


IC13
Delivery drive system CPU Clutch

Feed drive system IC12 Switch


EEP-ROM
Tray drive system
IC11 Sensor
Saddle section Communication Punch unit (option)
drive system IC
Interface pass Sensor
drive system IC6 Punch controller
ROM PCB

Motor

*: The position of delivery is shifted to the front/rear for each stack


to assist sorting.

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 1


C. Inputs to and Outputs from the Finisher • Outputs from the Finisher Controller PCB (1/2)
Controller PCB Finisher controller PCB

• Inputs to the Finisher Controller PCB (1/2) Binding clutch +24V


-1 -2 CN18-1

CN72
Finisher controller PCB FFC -2 -1 -2
B_CLU When the drive is transmitted,
FED CN44-3 CN43-1 CN42-3 CN16-10 +5V ‘1’.
Entry paper -1 -3 -1 -12 ENT_S When the sensor
sensor -2 -2 -2 -11 detects paper, ‘1’ . +24V
Feed motor -6 -1 CN10-1
-5 -2 -2
FPDHPD CN51-1 CN9-1 +5V
Paddle home -4 -3 -3

CN56
-3 -3 PDL_HP When the paddle is at FEEDMTR_A
position sensor FFM Switches between ‘1’ and
-2 -2 home position, ‘1’. -3 -4 -4
FEEDMTR_*A
-2 -5 -5 ‘0’ according to the
FEEDMTR_B direction of motor rotation.
FARHPD CN55-3 CN54-1 CN53-3 CN9-7 -1 -6 -6
Bundle roller +5V FEEDMTR_*B
-1 -3 -1 -9 When the swing guide
home position BDL_ROL_HP
-2 -2 -2 -8 is at home position, ‘1’.
sensor +24V
Paddle motor -6 -1 CN10-7
FFJHPD CN23-3 CN4 +5V -5 -2 -8
Aligning plate When the aligning
-1 -3 FJOG_HP -4 -3 -9

CN57
home position plate (front) is at PDLMTR_A
-2 -2 FPM -3 Switches between ‘1’ and
sensor (front) home position, ‘1’. -4 -10
PDLMTR_*A
-2 -5 -11 ‘0’ according to the
PDLMTR_B direction of motor rotation.
FRJHPD CN36-3 CN5-13 +5V -1 -6 -12
Aligning plate When the aligning PDLMTR_*B
home position -1 -15 RJOG_HP plate (rear) is at
-2 -14
sensor (rear) home position, ‘1’. +24V
Bundle exit motor -6 -1 CN13-1
-5 -2 -2
FAD CN30-3 CN29-1 CN28-9 CN5-1 +5V -4 -3 -3

CN59
Alignment -1 -3 -7 -3 When the sensor EJCTMTR_A
ADJ_TRAY_S FAM -3 -4 -4 Switches between ‘1’ and
tray sensor -2 -2 -8 -2 detects paper, ‘1’. EJCTMTR_*A
-2 -5 ‘0’ according to the
-5
EJCTMTR_B direction of motor rotation.
-1 -6 -6
FOBHPD CN31-3 -4 -6 -4 EJCTMTR_*B
Delivery belt +5V
-1 -6 -4 -6 When the delivery belt
home position EJCT_BLT_HP
-2 -5 -5 -5 is at home position, ‘1’. +24V
sensor Alignment motor
(front) CN63-1 CN62-5 CN3-1
-2 -4 -2
FBED CN32-3 -7 -3 -7 FJOGMTR_A
+5V -3 -3 -3 Switches between ‘1’ and
-1 -9 -1 -9 TRY_EMPS When paper is present FFJM FJOGMTR_*A
Tray paper sensor -2 -4 ‘0’ according to the
-2 -8 -2 -8 on the tray, ‘1’. -4
FJOGMTR_B direction of motor rotation.
-5 -1 -5
FJOGMTR_*B
FSLD CN35-3 CN34-1 CN33-3 CN5-10 +5V
Paper surface When the paper +24V
-1 -3 -1 -12 LVL_S Alignment motor
sensor -2 -2 -2 -11 surface is detected,
(rear) CN65-1 CN64-5 CN3-6
‘1’.
-2 -4 -7
RJOGMTR_A
-3 -3 -8 Switches between ‘1’ and
FFPD CN39-3 CN38-1 CN37-9 CN16-1 +5V FRJM RJOGMTR_*A
‘0’ according to the
Bookbinding -4 -2 -9
-2 -2 -8 -2 When paper is RJOGMTR_B direction of motor rotation.
BIND_P -1 -10
position sensor -1 -3 -7 -3 detected, ‘0’. -5
RJOGMTR_*B
BIND_L
When LED is lit, ‘1’.

• Inputs to the Finisher Controller PCB (2/2) • Outputs from the Finisher Controller PCB (2/2)
Finisher controller PCB Finisher controller PCB

Bookbinding FFHPD CN40-3 CN38-4 CN37-6 CN16-4 +5V


home position -1 -6 -4 -6 BIND_HP When at folding home Lift motor
sensor -2 -5 -5 -5
position, ‘0’. -2 -2 -2 -2 CN6-1
Switches between ‘+’ and
CN70

CN70 SIFTMTR_1
FFRHPD CN41-3 -7 -3 -7 +5V FLM ‘–’ according to the
Bookbinding -1 -1 -1 -1 -2 SIFTMTR_0 direction of motor rotation.
-1 -9 -1 -9 BIND_ROL_HP When the stack feed roller
roller home -2
-2 -8 -8 (upper) is at home position, ‘1’.
position sensor
FFED CN47-3 CN15-1
+5V
-1 -3 Staple motor
Bookbinding BIND_EMPS When the sensor
-2 -2
paper sensor detects paper, ‘1’. -2 -2 CN6-3
Switches between ‘+’ and
CN71

BINDMTR_1
FFE CN52-1 CN9-6 +5V FFSM ‘–’ according to the
-1 -1 -4 BINDMTR_0
Bookbinding -2 -5 BIND_CLK When the staple/fold motor is direction of motor rotation.
lock sensor -3 -4 rotating, alternates between
‘1’ and ‘0’.
FULD CN50-3 CN15-10 +5V
-1 -12 SIFT_UPLMT When the tray is at the
Lift upper sensor -2 -11
upper limit, ‘1’.
FLLD CN49-3 CN15-7 +5V
-1 -9
Lift lower sensor SIFT_DNLMT When the tray is at the
-2 -8
lower limit, ‘1’.

FLE CN48-3 CN15-4 +5V


Lift lock sensor -1 -6 While the lift motor
SIFT_CLK is rotating, alternates
-2 -5
between ‘1’ and ‘0’.
FFDD CN25-3 CN4-7 +5V
Front door sensor -1 -9 FDOOR_S When the front door
-2 -8 is open, ‘1’.

FCD CN24-3 CN4-4 +5V


Upper cover sensor -1 -6 TOPCOV_S When the upper cover
-2 -5 is open, ‘1’.

FMLD CN73-3 CN19-1 +5V


-1 -3 PAPER_F When the paper is
Tray middle sensor -2 -2 full, ‘1’.

FJSW +24VP
N. O.
Joint switch CN69-2 CN8-6

-1 -5
JOINT SW When connected to
the host machine, ‘1’.
FFDDW
N. O. CN68-2 CN8-4
Front door switch
-1 -3 When the front
FRONT SW
door is closed, ‘1’.
FSSSW
Stapler safety N. O.
switch CN66-2 CN8-2
When the swing
-1 -1 guide is closed, ‘1’.
STPLSAFE SW

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 2


• Inputs to and Outputs from the Finisher Controller PCB (1/2) D. Inputs to and Outputs from the Punch
Stapler unit Finisher controller PCB Controller PCB (option)
Staple shift home • Inputs to and Outputs from the Punch Controller PCB
position sensor
FSTHPD +5V
Punch controller PCB
CN72-5 CN72A-5 CN72A-5 CN11-3 SLID_HP When the stapler is at home
FPHPD J2008-3 J1006-4
position, ‘1’. Punch home +5V
-1 -6 When the hole puncher is
position sensor PUNCH
Staple driver home -2 -5 at home position, ‘0’.
position sensor
FSHPD +5V FPSHPD J2007-3 J1006-1 +5V
CN72-4 CN72A-4 CN72A-4 CN11-4 STPL_HP When the stapler is at Horizontal When the punch slide
-1 -3 unit is at home position,
stapling home position, ‘0’. registration SLIDE
-2 -2
home position ‘1’.
Staple empty sensor
sensor FPMCK J2009-3 J1006-7
FSD +5V +5V While the punch motor
Punch motor -1 -9
CN72-3 CN72A-3 CN72A-3 CN11-5 HOOK_S When the cartridge has CLOCK is rotating, alternates
lock sensor -2 -8
staples, ‘0’. between ‘0’ and ‘1’.

Self prime Waste full LED PCB +5V


sensor
LED121 J1005-1
FSPD +5V
CN72-2 CN72A-2 CN72A-2 CN11-6 When the staple is at top
SELF_P the stapler, ‘0’. -2
DUSTLED

+5V
+5V
CN72-6 CN72A-6 CN72A-6 CN11-2 Waste full photosensor PCB (FPDD) When the light is
CN72-1 CN72A-1 CN72A-1 CN11-7 blocked, ‘0’.
PT131
CN72-7 CN72A-7 CN72A-7 CN11-1 When the stapler is
STPL_CNCT connected, ‘0’. J1005-3
DUSTPTR

Staple shift motor 4


CN72-10 CN72B-5 CN72B-5 CN7-3 SLIDMTR_A
CN72-11 CN72B-4 CN72B-4 CN7-4 SLIDMTR_*A Switches between ‘1’ and
FSM CN72-12 CN72B-3 CN72B-3 CN7-5 ‘0’ according to the direction Side resist photo sensor PCB (FPTD)
SLIDMTR_B +5V
CN72-13 CN72B-2 CN72B-2 CN7-6 SLIDMTR_*B of motor rotation. +5V
J1007-12
PT1 -11 SREG1*
PT2 -10 SREG2*
PT3 -9 When paper is
SREG3*
+24V PT4 -8 detected, ‘0’.
CN2-1 SREG4*
PT5 -7
-3 PAEND*
GND
-4
GND
-5
TXD Communication line
-7 RXD -13
-6

+24V
Host
CN1-5
machine
CN1-3 • Outputs from the Punch Controller PCB
CN1-2 Punch controller PCB
Side resist LED PCB (FPSD) +5V
+5V
CN1-1 J1007-6
LED5
LED4
LED3
• Inputs to and Outputs from the Finisher Controller PCB (2/2) LED2
LED1
Finisher control PWB
Interface transport -1
unit inlet port LEDON5
sensor +5V -5
CNFJ2-1 CNFJ1- CN73A-8 LEDON4
-4
FJPID CNFJ1- CN73C-1 CN21- LEDON3 When ‘1’, LED goes ON.
"0" when paper is detected. -3
-3 -17 -17 -2 -7 -2 LEDON2
-2 -16 -16 -3 -6 -3 LVL_E_S -2
LEDON1

Punch motor
Interface transport J1002-1
unit outlet port Switches between ‘+’
sensor +5V and ‘–’ according to
CNFJ3-1 CNFJ1- CN73A-5 FPNM
FJPOD CNFJ1- CN73C-4 CN21-4 -2 the direction of motor
"0" when paper is detected. rotation.
-3 -14 -14 -5 -4 -5 LVL_P_S
-2 -13 -13 -6 -3 -6

Punch side resist motor


J1001-1
A
Interface transport -2 Switches the pulse
unit cover sensor B
FPSM -3 signals according to
CNFJ4-3 CN73A-2 +5V A* the rotation of the motor.
CNFJ1-
FJPDD "0" when the interface -4
CNFJ1- CN73C-7 CN21-7 B*
-2 -11 -11 -8 -1 -8 LVL_C_S transport cover is open.
-1 -10 -10 CN73D-2 CN73B-8 -9

Interface
transport
CNFJ5 CNFJ1-2 CN73B-
motor +24V
CNFJ1-2 CN73D-9 CN19-
The pulse signal is
-4 -7 -7 -4 -6 -2
A switched depending
-3 -6 -6 -5 -5 -3
*A on the motor RPM.
FJPM -1 -5 -5 -6 -4 -4
B
-2 -4 -4 -7 -3 -5 +24V
*B
-5 -3 -3 -8 -2 -6

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 3


2. Feed/Drive System b. Job Offset
The machine pulls the sheet once to the processing tray. It then
A. Outline moves the sheet to the front or the rear using the aligning plate.
The machine performs the following in response to the commands When it has deposited a specific number of sheets, it delivers them
coming from its host machine on the sheets arriving from the host in the form of a aligning plane. When the number of sheets stacked
machine for delivery: simple stacking, job offset, and stapling or on the processing tray reaches a specified value, the sheets are
folding (in two). delivered in a form of a stack.
If a punch unit (option) is installed, the sheets are pouched and
delivered to the delivery tray.
Sheets may be delivered in either of five ways (including one for
the punch unit):
Delivery method Normal delivery Simple stacking

Job offset

Stapling Front 1-point stapling

Rear 1-point stapling

Middle 2-point stapling


Punching

Saddle delivery Stitching Middle 2-point stapling

(1) Normal Delivery

a. Simple Stacking
The machine pulls in the sheet once to the processing tray and
then delivers it to the delivery tray.

Results of offset delivery (4 jobs)

4th set

3rd set 2nd set


1st set

(direction of delivery)

c. Stapling
The machine stacks sheets coming from its host machine on the
processing tray. When the number of sheets stacked on the pro-
cessing tray reaches a specified value, the finisher staples them
delivers the stapled stack to the delivery tray.

Tray

Paper

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 4


d. Saddle Delivery
The machine deposits a stack of sheets on the processing tray, sta- Finisher controller PCB (1/2)

drive signal RJOGMTR


Alignment motor (front)
drive signal FJOGMTR

drive signal FEEDMTR

Interface transport motor


ples it (middle 2-point), and then moves it to the saddle unit. The

Alignment motor (rear)

drive signal B_CLU


drive signal PDLMTR
saddle unit folds the stack in two, and delivers it to the bind tray.

drive signal RIM


Paddle motor

Bind clutch

Feed motor
FFJM FRJM FPM FFM FJPM

FFC
FAM

FSM
FLM

Bundle exit motor drive signal EJCTMTR


FFE
FFSM

Lift motor drive signal SIFTMTR

Staple slide motor drive signal

Bookbinding lock sensor


detect signal BIND_CLK
drive signal BINDMTR
Staple motor
SLIDMTR
Finisher controller PCB (2/2)

Finisher controller PCB

Entry paper detect signal


ENT_S

Bookbinding position
detect signal BIND_P
B. Feed/Delivery FED

(1) Outline
The machine forwards the sheets coming from its host machine to
the delivery tray, processing tray, or saddle unit according to the
FFPD
type of delivery used. The sheets forwarded to the processing tray
or the saddle unit are offset, stapled, or folded.
The following table shows the motors that are associated with mov-
ing and aligning sheets. These motors are controlled (rotated clock-
wise or counterclockwise) by the microprocessor (CPU) on the
finisher controller PCB.
The paper path is equipped with the sensors shown in the following
figure used to monitor the arrival or passage of sheets.
If a sheet fails to arrive at or move past a specific sensor within a
specific period of time, the finisher controller will assume a jam, and
stops the ongoing operation and, at the same time, communicates Connector on
the presence of a jam to the host machine. Notation Name Description finisher
controller PCB
Connector on FED Entry paper sensor Photointerrupter CN16
Notation Name Description finisher FFPD Bookbinding position Photointerrupter CN16
controller PCB sensor
FFM Feed motor Stepping motor CN10
FPM Paddle motor Stepping motor CN10
FAM Bundle exit motor Stepping motor CN13
FFJM Alignment plate motor Stepping motor CN3
(front)
FRJM Alignment plate motor Stepping motor CN3
(rear)
FFSM Staple motor Brush DC motor CN6
FJPM Interface transport motor Stepping motor CN21

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 5


C. Job Offset (3) Offset Operation
(1) Outline Each sheet is pulled forward or backward using the aligning plate
(front) and the aligning plate (rear).
"Job offset" refers to the operation by which the machine delivers a
set of sheets with them pulled forward or backward for sorting. The offset operation is performed each time a sheet is pulled onto
the processing tray.
Switching between the forward and backward directions is made
using an aligning plate (front) and an aligning plate (rear). Offsetting in the forward direction
The sheet coming between the delivery rollers is fed onto the pro- Aligning plate (rear)
cessing tray and then fed toward the stopper by the paddle.
A swing guide is at the up position while a sheet is being pulled
onto the processing tray or during alignment. It is at the down posi-
tion during stack feeding, stack delivery, or stapling.
At power-on, the finisher controller PCB drives the aligning motor Sheet to be offset
(front) (FFJM) and the aligning motor (rear) (FRJM) to return the
two aligning plates to their home positions.

Sensor Symbol Connector


Aligning home position sensor (front) FFJHPD CN4-3
Aligning home position sensor (rear) FRJHPD CN5-15
Stack roller home position sensor FARHPD CN9-9 Tray
Paddle home position sensor FPDHPD CN9-3 Aligning plate (front)

Function Motor Symbol Offsetting in the backward direction


Drives the aligning plate (front) Aligning motor (front) FFJM Aligning plate (rear)
Drives the aligning plate (rear) Aligning motor (rear) FRJM
Drives the swing guide drive Paddle motor FPM
Drives the paddle (feeds paper) Paddle motor FPM

Aligning home position sensor (rear)


Aligning plate
(rear)
(FRJHPD) Sheet to be offset

Light-shielding plate

Alignment motor (front)


(FFJM)

Alignment Tray Aligning plate (front)


motor (rear) (FRJM)

Aligning plate (4) Stack Delivery Operation


(front)
Stack delivery takes place when 1 sheet of large-size paper or 25
Light-shielding plate sheets of small-size paper have been stacked on the processing
(Front)
Paper tray with them offset in either direction.
Aligning home position sensor (front)
(FFJHPD)
The paddle motor (FPM) rotates and the swing guide descends to
hold the paper stack between the upper and lower stack delivery
rollers. The stack delivery motor (FAM) rotates in the forward direc-
(2) Processing Tray Paper Stacking Operation
tion to rotate the delivery rollers, feeding the paper stack in the
A sheet coming between the delivery rollers is fed onto the pro- delivery direction. The delivery belt home position sensor is turned
cessing tray. Then, the paddle taps on the sheet surface to locate OFF. The delivery motor is driven a specified number of pulses,
the sheet against the processing tray stopper. causing the swing guide to ascend. Next, the paper delivery motor
Paper is driven. Next, the delivery motor is driven to deliver the paper
Aligning plate
stack with the nails of the delivery belt that rotates in sync with the
Paddle stack delivery rollers.
Stack delivery roller (upper)

Swing guide

Swing guide

Processing tray stopper


Delivery belt
Stack delivery roller (lower)

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 6


Job offset sequence B. Stapling Operation
Start signal When stacking and alignment of paper on the processing tray are
complete, the finisher controller PCB drives the paddle motor
Host machine delivery signal
Entry paper sensor
(FFD)
Alignment tray sensor
(FPM) in the reverse direction and lowers the swing guide. When
(FAD) the swing guide descends, the paper stack is sandwiched between
Feed motor (FEM)
the upper and lower stack delivery rollers.
Bundle exit motor (FAM)
The finisher control PCB shifts the stapler according to the speci-
Delivery belt home
position sensor (FOBHPD) fied staple position to perform stapling. (Only for B5-R, 1-position
4 ms (A4) ∗ 4 ms (A4) ∗ 4 ms (A4) ∗ 4 ms (A4) ∗ bottom stapling is made at the rear side of 2-posiiton stapling.)
Paddle motor (FPM)

Paddle home position When the stapler shifts toward you, the process tray stopper is put
sensor (FPDHPD)
Bundle roller home position
down to the lower side.
sensor (FARHPD)
Staple safety switch Paper stack
(FSSSW)
Alignment motor (front) 60msec 30msec 220msec
(FFJM) Swing guide
Alignment home position
sensor (front) (FFJHPD) Stack delivery roller (upper)
Alignment motor (rear)
(FRJM) Processing tray
Alignment home position stopper
sensor (rear) (FRJHPD)
Delivery tray Stapler
∗ Variable by the size : CW rotation : CCW rotation

Stack
delivery
3. Stapling Operation roller
(lower)
A. Outline
Staple operation is performed to staple a specified sheets of paper
using a stapler unit.
The stapling position depends on the staple mode and paper size.
Bundle roller home
When the machine starts immediately after power-on, the finisher position sensor
Paddle motor (FPM)
controller PCB drives the staple shift motor (FSM) to return the sta- (FARHPD)
pler unit to the home position. The stapler unit starts moving toward
Light-shielding plate
the front of the stapler frame. It stops when the staple shift home
position sensor (FSTHPD) on the slide PCB located under the sta-
pler unit. Next, the staple shift motor (FSM) is driven a specified
number of pulses. The stapler unit moves to rear standby position
at the back of the machine, entering the standby state.

Sensor Symbol Connector Function Remarks


Staple shift FSTHPD CN11-3 Detects the home
home position position for the
— Staple safety
sensor stapler moving switch (FSSSW)
back and forth.
Staple drive FSHPD CN11-4 Detects the home In the
home position position for the stapler
sensor stapling operation Swing guide
Self prime FSPD CN11-5 Detects presence In the
Stack delivery
sensor or absence of stapler roller (upper)
staples in the
cartridge.
Staple empty FSD CN11-6 Cartridge empty In the Stack delivery
sensor detection stapler roller (lower)

Function Motor Symbol Remarks


Moves the stapler. Staple shift motor FSM —
Performs stapling operation Staple motor FFSM —

Stapler

(Deliver direction)
Paper stack

Staple
shift motor
(FSM) Light-shielding plate

Staple shift home position sensor (FSTHPD)

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 7


C. Delivery Operation after Stapling D. Stapler Unit
When stapling is complete, the finisher controller PCB drives the The staple motor (FFSM) is used to perform stapling operation.
stack delivery motor (FAM) in the forward direction to feed the This motor rotates the cam one turn for stapling. The home position
paper stack (sandwiched between the stack delivery rollers) in the of this cam is detected by the staple drive home position sensor
delivery direction. The delivery belt home position sensor (FOB- (FSHPD).
HPD) is turned OFF. The stack delivery motor (FAM) is driven a The staple motor (FFSM) is rotated in the forward or reverse direc-
specified number of pulses, causing the swing guide to ascend. At tion under the control of the macro computer (IC13) on the finisher
the same time, the staple shift motor (FSM) is driven to return the controller PCB.
stapler back to the standby position, followed by driving of the stack
When the staple drive home position sensor (FSHPD) is OFF, the
delivery motor (FAM). Then, the paper stack is delivered with the
finisher controller PCB rotates the staple motor (FFSM) in the for-
nails of the delivery belt that rotates in sync with the stack delivery
ward direction until the sensor turns ON, allowing the staple cam to
rollers.
the original position.
Paper stack The staple empty sensor (FSD) is used to detect presence/
absence of a staple cartridge in the machine. The self prime sensor
(FSPD) is used to detect presence/absence of staples in the car-
Swing guide
tridge.
The finisher controller circuit does not drive the staple motor
Stapler (FFSM) unless the staple safety switch (FSSSW) is ON (the swing
Delivery tray guide is close). This assures safety in case where you happen to
put your finger in the stapler.

Delivery belt

Stack delivery
roller (lower)

Stack roller home position


sensor (FARHPD)
Paddle motor (FPM)

Light-shielding plate

Staple safety
switch (FSSSW)

Swing guide

FFSM

Stack delivery Stack delivery roller


roller (lower) (upper)
Staple drive home position detect signal

Staple empty detect signal

Staple motor drive signal


Cartridge detect signal

Finisher controller PCB

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 8


(1) Stapler Movement Controller 4) Middle 2-point stapling (bind mode)
The stapler unit is moved by the staple shift motor (FSM). Its home The stapler waits at the back. The stapler moves to and
position is detected by the staple shift home position sensor returns from the stapling position for each stapling operation.
(FSTHPD). The stapler waits at the back irrespective of the staple The stapler first staples a paper stack at the rear stapling posi-
mode and paper size. After paper has been stacked on the pro- tion and then staples it at the front stapling position.
cessing tray, the stapler is moved to the specified stapling position
in response to the stapling command from the host machine.
The figure below shows the standby position of the stapler and the
Standby position
stapling position depending on the staple mode.
1) Front 1-point stapling
Stapler
The stapler waits at the back. The stapler moves to and
returns from the stapling position for each stapling operation. Stapling position

Stopper
Standby position
Feed direction Stapling position

Stapler

Feed direction
Stapling Operation Sequence
Stopper
Rear 1-point Stapling of 2 Sheets
Stapling position Start signal
Host machine delivery signal

Entry paper sensor (FED) Staple Stack delivery

Alignment tray sensor


2) Rear 1-point stapling (FAD)

The stapler waits at the back. The stapling position is the same Feed motor (FFM)

as the standby position. (Except B5R) Bundle exit motor (FAM)

Exit belt home position 10msec


sensor (FOBHPD)
Standby position 4ms (A4) ∗ 4ms (A4) ∗
Paddle motor (FPM)
Stapling position
Paddle home position
sensor (FPDHPD)
Stapler Bundle roller home
position sensor (FARHPD)
Staple safety switch
(FSSSW)
Alignment motor (front)
(FFJM)
Alignment home position
sensor (front) (FFJHPD)
Feed direction
Staple motor (FFSM) 20msec

Stopper Staple drive home position


sensor (FSHPD)

∗ Variable by the size : CW rotation : CCW rotation

3) Middle 2-point stapling


The stapler waits at the back. The stapler moves to and
returns from the stapling position for each stapling operation.
The stapler first staples a paper stack at the rear stapling posi-
tion and then staples it at the front stapling position.

Standby position

Stapler
Stapling position

Stopper
Feed direction Stapling position

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 9


4. Delivery Tray Operation 5. Saddle Unit
A. Outline A. Basic Operations
The machine has a delivery tray in the finisher unit and a bind tray (1) Outline
in the saddle unit.
The machine stitches a stack of sheets (middle 2-point), then folds
The bind tray in the saddle unit is of the fixed type and all the folded the stack in two in the finisher. These operations are controlled by
paper stacks are delivered to this tray. This tray has a bind tray the finisher controller PCB.
sensor (FFED) to detect presence/absence of paper.
The finisher controller PCB is controlled by the commands from the
The delivery tray in the finisher unit is moved up and down using a host machine.
lift motor (FLM).
The finisher has a tray paper sensor (FBED) to detect presence/ B. Feed/Drive System
absence of paper on the stack tray. (1) Outline
The home position sensor of the delivery tray is detected by the This machine stitches the paper stack coming from the finisher,
paper surface sensor (FSLD). When paper has already been folds it, and delivers it to the bind tray in the saddle unit in response
stacked on the delivery tray, the home position is on the top surface to the commands from the host machine.
of the stacked paper. When paper has not yet been stacked on the
That is, the machine performs the following operations:
delivery tray, the home position is at the position where the edge of
the delivery tray is detected. At power-on, the finisher controller a. Paper feed-in
PCB drives the lift motor (FLM) to return the delivery tray to the b. Stitching
home position. c. Stack feed
d. Folding/delivery
When the paper coming from the processing tray is stacked on the
delivery tray, the lift motor (FLM) is driven a specified number of
pulses, causing the delivery tray to descend. Clock pulses are
detected by the lift lock sensor (FLE). Then, the delivery tray
returns to the home position for the next stacking operation.
The upper limit of the delivery tray is detected by the lift upper limit
sensor (FULD). When the lift upper limit sensor (FULD) is turned
ON, the finisher controller PCB stops the lift motor (FLM) that is
ascending. b) Stitching
a) Paper feed-in
The lower limit of the delivery tray is detected by the lift lower limit
sensor (FLLD). When the lift lower limit sensor (FLLD) is turned
c) Stack feed
ON, the finisher controller PCB stops the lift motor (FLM) that is
descending.
The finisher unit has a tray middle sensor (FMLD) to detect over-
stacking of large-size or mixed paper according to the stack height. d) Folding/delivery

Lift upper sensor


(FULD)

Tray paper sensor a. Paper feed-in


Lift lower sensor
(FBED) After being aligned on the processing tray, a stack of sheets is
(FLLD)
Paper level sensor sandwiched between the stack delivery rollers. As the stack deliv-
(FSLD)
ery rollers rotate, the stack is fed toward the saddle unit.
Edge
Stack delivery roller (upper)
Lift lock sensor
(FLE)
Delivery tray Paper stack

Tray middle sensor


(FMLD)

Lift motor (FLM)

Stack delivery roller


(lower)

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 10


b. Stitching C. Paper Feed System
When the center of the paper stack (stitching position) reaches the (1) Outline
stapler's staple position, the stapler stitches the paper stack.
The paper feed system feeds a stack of sheets (coming from the
When only one sheet is fed from the host machine, the next step finisher) to the position where the center of the paper stack (stitch-
(stack feed) is performed without performing the stitching opera- ing position) is aligned to the stapler's staple, allowing the next step
tion. (stitching and folding) to be performed.
When sheets of paper have been stacked and aligned on the pro-
Staple
Stapler (upper) cessing tray, the paddle motor (FPM) rotates in the reverse direc-
tion, causing the swing guide to descend. As the swing guide
descends, the paper stack is sandwiched between the upper and
lower stack delivery rollers. The stack delivery motor (FAM) rotates
in the reverse direction, feeding the paper stack toward the saddle
unit. When the leading edge of the paper stack reaches the binding
position sensor (FFPD), the finisher controller PCB drives the stack
delivery motor (FAM) a specified number of motor pulses to stop
the center of the paper stack (stitching position) at the stapler's sta-
ple position. Before the paper stack passes through the stack feed
rollers, the feed motor (FFM) is driven to rotate the stack feed roller
Stapler (lower)
(lower) so that the leading edge of the paper stack is not bent.
Stack delivery roller (upper)

Paper stack

c. Stack feed
The stack feed rollers feed the paper stack to the stack folding/ Fold position sensor

delivery position where the center of the stack (stitched position) is


level with the paper pushing plate and paper folding roller's nip part. Stack delivery roller
(lower)

Stack feed roller (lower)

Stack feed roller (upper)

Paper pushing plate

D. Stack Feed System


(1) Outline
The stack feed system feeds the stitched paper stack to the folding
position.
When stitching is complete, the feed motor (FFM) rotates, causing
Stack feed roller (lower)
the stack feed roller (upper) to descend. The paper stack is sand-
Paper fold roller
wiched between the stack feed rollers. Then, the bind clutch (FFC)
is turned ON to rotate the feed motor (FFM) in the forward direc-
d. Folding/delivery tion, thus feeding the paper stack to the folding position. The feed
The paper pushing plate pushes in the center of the paper stack to amount is equivalent to the number of pulses used to drive the feed
feed it toward the paper fold rollers. Then, the paper fold rollers and motor (FFM) until the paper stack reaches the folding position.
bind delivery rollers deliver the paper stack to the bind tray.

Stack feed roller (upper)

Fe
ed
am
ou
nt

Bind delivery rollers Stack feed roller (lower)


Paper fold rollers

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 11


E. Fold/Delivery System
(1) Outline
The paper fold mechanism consists of a guide plate, paper fold roll- Bookbinding home position
ers, and a paper pushing plate. sensor (FFHPD)

The guide plate, paper fold rollers, and paper pushing plate are
driven by the staple motor (FFSM). The drive force is transferred Paper pushing plate

with a combination of gears and cams. Motor operation is moni-


tored by the binding lock sensor (FFE).
Paper fold roller (upper)
Until the paper stack reaches the folding position, the guide plate
covers the paper fold rollers to act as a paper path through which a
paper stack is fed to the saddle unit and to prevent a paper stack Staple motor FFSM
from touching the rollers. (FFSM)

A binding home position sensor (FFHPD) is provided to detect the


Paper fold roller (lower)
positions of the paper fold rollers and paper pushing plate.
The paper stack folded in two by the paper fold rollers is delivered
by bind delivery rollers. The bind delivery rollers are also driven by
the staple motor (FFSM). Paper stack

A bind tray sensor (FFED) is provided on the bind tray to detect


presence/absence of a paper stack; however, it is not used to
detect a jam.
(2) Paper Folding
Paper is folded using paper fold rollers and a paper pushing plate. Paper stack
Almost concurrently with the start of roller rotation, the paper push-
ing plate starts operating to push the paper stack into the gap
between the paper fold rollers. When the paper stack is fed about
10 mm with the rotation of the paper fold rollers, the paper pushing
plate returns to the home position. Then, the paper stack is deliv- Inlet
ered to the bind tray using the paper fold rollers and bind delivery
rollers.
Half the entire surface of each paper fold roller is uncovered
excluding the central area and the area at the left and right ends. Paper push plate
The uncovered surface of the upper paper fold roller comes in
touch with the uncovered surface of the lower paper fold roller only
Outlet
at the center and left and right ends, allowing a paper stack to be
fed without causing creases. The other half of the upper paper fold
roller that is covered comes in touch with the other half of the lower
paper fold roller that is also covered, allowing a paper stack to be
folded while being fed.

Sensor flag Folds/feeds a paper stack.

Bookbinding home position


Feeds a paper stack.
sensor (FFHPD)
Came Staple
Feed motor (FFM) Fold, Delivery
Paper pushing plate
Paper stack Bundle exit motor (FAM)

Paddle motor (FPM)


Paper fold roller (upper)
Paddle home position
sensor (FPDHPD)
Bundle roller home position
Staple motor FFSM
sensor (FARHPD)
(FFSM)
Staple safety switch
(FSSSW)

Staple shift motor (FSM)


Paper fold roller (lower)
13571msec
Staple motor (FFSM)

Staple drive home position 50msec


sensor (FSHPD)
Bookbinding position
sensor (FFPD)
Bookbinding roller home
position sensor (FFRHPD)

Bookbinding clutch (FFC)

Bookbinding home
position sensor (FFHPD)
Bookbinding paper
sensor (FFED)

: CW rotation : CCW rotation

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 12


F. Punch Unit (AR-PN1A/B/C/D) The punch motor (FPNM), punch unit, and sensors make up the
punch slide unit, which moves to the front/rear to suit the selected
(1) Basic Operations
paper size. The movement to the front/rear is driven by the punch
a. Outline horizontal registration motor (FPSM). The home position of the
punch slide unit is detected by the punch horizontal registration
The punch unit is an option, and is designed for installation to the
home position sensor (FPSHPD), and the punch horizontal regis-
pickup assembly of the finisher.
tration motor (FPSM) is a stepping motor.
The punch unit is not equipped with a paper feeding mechanism,
The punch motor (FPNM) and punch horizontal registration motor
and the sheets from the host machine move through the punch unit
(FPSM) are controlled with various commands from the finisher
and then the feed system of the finisher. When the trailing edge of a
controller PCB as well as the commands from the punch controller
sheet from the host machine reaches the punch unit, the sheet is
PCB. The waste paper occurring as the result of punching is col-
stopped once, and the punch shaft is rotated to punch a hole along
lected in the waste paper case. The case is monitored by the
the trailing edge. These operations are controlled with various com-
LED121 on the waste full LED PCB and PT131 on the waste full
mands from the finisher controller PCB as well as the commands
photosensor PCB (FPDD).
from the punch controller PCB.
Punch controller PCB (1/2)
Punch drive system

Horizontal registration
motor (FPSM) drive signal
Horizontal registration detection
Horizontal registration

signal (LED1 - 4, PT1 - 4)

Punch motor (FPNM)


Trailing edge detection signal
drive system

drive signal
(LED5, PT5) FPTD
Finisher unit control system

FPSD1 - 4
Punch controller PCB
PT1
2
3
4
5
LED1
2
3
4
5

PT131

(2) Punching Operation

Punch home position sensor detection signal (FPHPD)


a. Outline
The punch unit is located in the pickup assembly of the finisher,
and is used to punch holes in sheets that have been sent from the

Horizontal registration home position


(FPSHPD) detection signal SREGHP
host machine and stopped inside it. When the trailing edge of a
Punch motor lock sensor (FPMCK)
detection signal PUNCHCLK
sheet reaches the punch unit, the inlet roller of the finisher assem-

Waste full detection signal


LED121

bly stops the sheet to punch a hole along the trailing edge of the

(LED121,PT131) FPDD
sheet.
The punch unit consists of a die and hole puncher (punch blade).
The hole puncher is driven by the punch motor (FPNM). It is
attached to the eccentric cam of the punch shaft, and the rotation of
the punch shaft is converted into reciprocating motion for punching
operation. Punch controller PCB (2/2)

The punch motor (FPNM) is a DC motor. The home position of the


punch shaft is detected by the punch home position sensor
(FPHPD). To make sure that the punch motor (FPNM), which is a
DC motor, stops exactly at its home position, the punch motor
(FPNM) is stopped in relation to the count of the clock pulses kept
by the punch motor lock sensor (FPMCK). A single punching oper-
ation is executed by rotating the punch shaft 180° from its home
position.
As many as five light-receiving transistors (photosensor PCB) are
mounted over the inlet paper path of the punch unit; on the other
hand, as many as five LEDs (LED PCB) are mounted under the
path, together serving as five sensors. The frontmost sensor
(LED5, PT5) is used as a trailing edge sensor (FPTD) to detect the
training edge of sheets, and the remaining four (LED1 through
LED4, PT1 through PT4) are used as horizontal registration sen-
sors (FPSD1 through FPSD4) to detect the rear position of sheets
when punching holes.

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 13


b. Punching Operation <1> A hole is made along the trailing edge of the 1st sheet.
The hole puncher is driven by the punch motor (FPNM). The home Sensor flag
position for the hole puncher is detected by the punch home posi-
Punch home position
tion sensor (FPHPD). sensor (FPHPD)

The punch unit comes in four types, selected to suit the country of Punch shaft
installation: 2-hole (Punch Unit-J1), 2- and 3-hole (Punch Unit-K1),
or two types of 4-hole (Punch Unit-G1, Punch Unit-H1).
The 2-hole and 4-hole types punch a hole when the punch shaft is Eccentric cam
rotated 180° from the home position, causing the punch to make a Hole
puncher
single round trip. The 2-/3-hole type punches a hole, but the cir- Die
Paper
cumference of the punch shaft is divided into two (half for 2-hole Die Waste paper
and the other half for 3-hole). (punch shaft at rest/ (punch shaft CW rotation by 180°/
(punch shaft CW rotation
1) 2-Hole, 4-Hole Type home position) by 90°/hole made) end of punching operation)

The home position is identified when the punch home position While two holes are being made, the 3-hole puncher
sensor (FPHPD) is ON. The punching operation for the first makes a single round trip in escape direction.
sheet ends when the punch shaft has rotated 180° and the
punch home position sensor (FPHPD) goes ON; the punching
operation for the second sheet ends when the punch shaft has
rotated 180° in reverse and the punch home position sensor
(FPHPD) goes ON.
<1> A hole is punched along the trailing edge of the 1st sheet.
Sensor flag

Punch home position


sensor (FPHPD)

Punch shaft

(punch shaft at rest/ (punch shaft CW rotation by 90°/ (punch shaft CW rotation by 180°/
Eccentric cam
Hole home position) punch at upper limit) punch back to initial position)
puncher
Die Paper
<2> Holes are made along the trailing edge of the 2nd sheet.
Die Waste paper
(punch shaft at rest/ (punch shaft CW rotation (punch shaft CW rotation by 180°/
home position) by 90°/hole made) end of punching operation)

<2> A hole is made along the trailing edge of the 2nd sheet.
Sensor flag

Punch home position


sensor (FPHPD)

Punch shaft

Eccentric cam
Hole (punch shaft at rest/ (punch shaft CCW rotation (punch shaft CCW rotation by 180°/
puncher home position) by 90°/hole made) end of punching operation)
Die Paper

Die Waste paper


While two hole are being made, the 3-hole puncher makes
(punch shaft at rest/ (punch shaft CW rotation (punch shaft CW rotation by 180°/ a single round trip in escape direction (moving up the hole
home position) by 90°/hole made) end of punching operation) puncher).
2) 2-/3-Hole Type
The home position is identified when the punch home position
sensor (FPHPD) is ON. To make two holes, the punching oper-
ation for the first sheet ends when the punch shaft rotates 180°
(half circumference) and the punch home position sensor
(FPHPD) goes ON. At this time, the 3-hole puncher makes a
single round trip in escape direction (moving up the hole
puncher) on a half circumference of the punch shaft. The
punching operation for the second sheet ends when the punch
shaft has rotated 180° counterclockwise and the punch home
position sensor (FPHPD) goes ON (half circumference).
At this time, the 3-hole puncher makes a single round trip in
escape direction (moving up the hole puncher) on the other (punch shaft at rest/ (punch shaft CCW rotation by (punch CCW rotation by 180°/
half circumference of the punch shaft. home position) 90°/punch at upper limit) punch back at initial position)

The punching operation takes place as follows when making


two holes in two sheets of paper:

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 14


(3) Horizontal Registration Operation 3) When the trailing edge sensor (FPTD) detects the trailing edge
The horizontal registration drive for the punch slide unit is provided of the sheet, the drive of the feed motor (FFM) is stopped,
by the punch horizontal registration motor (FPSM). The home posi- thereby stopping the sheet. Then, the punch motor (FPNM) is
tion of the punch slide unit is detected by the punch horizontal reg- driven to punch holes in the sheet.
istration home position sensor (FPSHPD). The punch slide unit
detects the trailing edge of sheets using the trailing edge sensor
(FPTD) and the horizontal registration sensors (FPSD1 through 4),
and causes a move to a specific position matching the trailing edge
of each sheet (in relation to the size of the sheet).
The horizontal registration operation takes place as follows:
1) When the leading edge of a sheet from the host machine is
detected by the trailing edge sensor (FPTD), the punch hori-
zontal registration motor (FPSM) starts to move the punch
slide unit toward the front.
Punch
Punch side resist home position sensor
(FPSHPD)

Punch slide unit

Punch side resist motor


(FPSM)

4) When the punching operation ends, the feed motor (FFM) of


Trailing edge sensor the fisher unit is driven and, at the same time, the punch hori-
(FPTD) zontal registration motor (FPSM) is rotated in reverse to return
the punch slide unit to its home position.
5) For each sheet that arrives in succession, the punch slide unit
is returned to its home position, and is caused to repeat steps
1 through 4.
(direction of
paper delivery)
Trailing edge sensor
(FPTD)
Horizontal registration
sensor (FPSD1 - 4)
Punch home position
sensor (FPHPD)
Punch horizontal registration
Paper home position sensor (FPSHPD)
Punch horizontal
2) When the horizontal registration sensor (FPSD1 through 4) registration motor (FPSM)

suited to the paper size signal from the host machine detects Punch motor (FPNM)
the rear edge of the sheet, the punch horizontal registration
Feed motor (FFM)
motor (FPSM) causes a farther move to a specific position,
and stops the punch slide unit.
: CW rotation : CCW rotation

Horizontal registration sensor 1 (FPSD1);


used to detect the edge of sheets of A3, A4,
8.5" x 11", 11" x 17".
G. Detecting Jams
(1) Outline
Horizontal registration sensor 2 (FPSD2);
used to detect the edge of sheets of B4, B5, The microprocessor (CPU) on the finisher controller PCB is pro-
8.5" x 11"R, 8.5" x 14". grammed to check for jams in the finisher/saddle/puncher (option)
at such times as set in advance. It identifies a jam in reference to
Horizontal registration sensor 3 (FPSD3); the presence/absence of paper at a specific sensor. If a jam is
used to detect the edge of sheets of A4R. found, the finisher controller PCB communicates the nature of the
jam to the host machine in the form of a code(which may be
Horizontal registration sensor 4 (FPSD4);
checked in service mode of the host machine).
used to detect the edge of sheets of B5R.

FPHPD

FED
FAD

FFPD

FED : Entry paper sensor


FAD : Alignment tray sensor
FFPD : Bookbinding position sensor
FPHPD : Punch home position sensor

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 15


a. Inlet Paper Sensor (FED) Delay Jam
Host machine delivery signal Host machine delivery signal

approx. 1.0sec.* approx. 1.0sec.*


Jam check Jam check

Entry paper sensor Normal Entry paper sensor Jam


(FED) (FED)

Feed motor (FFM) Feed motor (FFM)

* Variable depending on the paper size. (Because the paper feed speed may differ according to the paper size. (A4:1.0 sec.))

b. Inlet Paper Sensor (FED) Stationary Jam

approx. 1.4sec.* approx. 1.4sec.*


Jam check Jam check

Entry paper sensor Normal Entry paper sensor Jam


(FED) (FED)
Feed motor (FFM) Feed motor (FFM)

* Variable depending on the paper size. (Because the paper feed speed may differ according to the paper size. (A4:1.4 sec.))

c. Binding Position Sensor (FFPD) Delay Jam

1080 ms 1080 ms
Jam check Jam check
Binding position Normal Binding position Jam
sensor (FFPD) sensor (FFPD)
Stack delivery motor Stack delivery motor
(FAM) (FAM)

d. Binding Position Sensor (FFPD) Stationary Jam

approx. 16.2sec. approx. 16.2sec.


Jam check Jam check

Binding position Normal Binding position Jam


sensor (FFPD) sensor (FFPD)
Staple motor (FFSM) Staple motor (FFSM)

e. Power-On Jam
Paper is detected inside the finisher at power-on or when the door is closed.

f. Door Open Jam


The finisher is disconnected from its host machine or the front door, or the upper cover is opened while the system is in operation (paper on the
move).

g. Staple Jam
The staple drive home position sensor (FSHPD) does not go OFF 600 msec after the stapler is driven. Or, it does not return to its home position
(where the sensor goes ON).

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 16


H. Power Supply System
(1) Finisher/Saddle Assembly

a. Outline
When the host machine is turned on, it supplies the finisher controller PCB with 24VDC and 5VDC. 24VDC is for the motors and clutches.
24VDC and 5VDC are also supplied as a relay pass drive, 5VDC is used to drive sensors and ICs on PCBs.
If a punch unit (option) is installed, power is also supplied to the punch controller PCB.
Some of 24 VDC used to drive motors is cut off when the joint switch (FJSW), front door switch (FFDDW), or stapler safety switch (FSSSW) is
open.
The block diagram of the power supply system is below.
Front door switch
(FFDDW) Stapler safety switch
Joint switch
(FJSW) (FSSSW)

24V
Motor

24V
Motor
24VC

Circuit Breaker 24V


Clutch
(CB1)

Finisher
Host controller PCB
machine 5V
Circuit protector Sensor
(CP2)

5VDC 5V
Logic system

Punch controller PCB


(punch unit; option)

Relay interface PCB

b. Protective Mechanisms
A circuit breaker (CB1) is monitored to protect the 24 VDC system used to drive the motors against overcurrent. The 24-V system used to drive
the feed motor (FFM), paddle motor (FPM), and stack delivery motor (FAM) is equipped with a fuse which melts in the presence of overcurrent.
(2) Punch Unit (option)

a. Outline
When the host machine is turned on, the punch unit is supplied by the finisher controller PCB with 24-V and 5-V power.
The 24-V power is used to drive the motors, while the 5-V power is used by sensors and the ICs on the punch controller PCB.
The 24-V power to the motors will be cut off when the joint switch (FJSW) or the front door switch (FFDDW) of the finisher unit is open.
The following is a block diagram for the power supply system:

24 V 24 V
Motors

Finisher Punch controller PCB


controller 5V
Sensors
PCB

5V 5V
Logic system

b. Protective Mechanisms
The 24-V system used to drive the punch motor (FPNM) and the punch horizontal registration motor (FPSM) is equipped with a built-in fuse
which melts in the presence of overcurrent.

MX-FNX2/AR-PN1/MX-RBX1 OPERATIONAL DESCRIPTION 5 – 17


[6] DISASSEMBLY AND
âºíuÇ´ 2) Remove the
Service front cover.
Manual
ASSEMBLY
1) Turn off the host machine, disconnect the saddle stitch finisher
connctor.
2) Free the lock, and remove the saddle stitch finisher from the
host machine.

(3) Rear Cover


1) Remove the rear cover.

1. Saddle stitch finiser (MX-FNX2)


A. Externals and Controls
(1) Delivery tray
1) Remove the delivery tray.

(4) Upper Cover


1) Remove the front cover. (See (2).)
2) Remove the rear cover. (See (3).)
3) Open the upper cover, and remove the cover band.

1
(2) Front Cover
1) Open the front door, and remove the knob.

1 4) Detach the processing cover, and remove the upper cover.

2
1

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 1


(5) Processing Tray Upper Cover (7) Removing the Saddle Guide
1) Remove the front cover. (See (2).) 1) Remove the delivery tray. (See (1).)
2) Remove the rear cover. (See (3).) 2) Remove the front cover. (See (2).)
3) Remove the upper cover. (See (4).) 3) Remove the rear cover. (See (3).)
4) Disconnect the connector [1] and remove the screw [2]. 4) Free the delivery tray support plate (front) [1] and the delivery
tray support plate (rear) [2] to the outside from the rail grooves.
5) Remove the four screws [3].

[3] [3]
[2]

[1]

[3]
[3]

[2]
6) Shift the side guide [4] lightly to the front, and free the engage-
ment of the paper surface detecting lever (rear) [5]; then,
detach the side guide [4].

[1]
[5]

5) While lifting the processing tray cover [3], disconnect the con-
nector [4], then remove the processing tray upper cover [3].

[3]

[4]

NOTE: Be sure to mount the side guide after securely fitting the
paper surface detecting lever (rear) [5] in the groove of the
paper surface detecting lever (middle) [6].
After completion of mounting, push the paper surface
detecting lever several times to make sure that side guide
is mounted securely.
[4]

(6) Upper Right Cover, Middle Right Cover


1) Remove the front cover. (See (2).)
2) Remove the rear cover. (See (3).)
3) Open the upper cover, then remove the upper right cover and
the middle right cover.

[5] [6]

[5]

[6]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 2


B. Feeding System 1) Detach the gear cover [2] from the staple driver [1].
(1) Removing the Stapler Unit 2) Remove the E-ring [3] to detach the side cover [5] of the staple
clincher [4].
1) Open the front door.
2) Slide out the stapler unit while pressing the stopper. [4]

3
[3]

[5]

[2]
2 [1]

3) Remove the two E-rings [6] to remove the staple jam releasing
gear [7], timing belt [8], and relay gear 1 [9]. Remove the
spacer and spring at the back of the staple jam releasing gear.
NOTE: Do not remove the stapler stapler frame shaft. If removed, 4) Remove the screw [10] and spring [11] to remove the belt ten-
the position where the staple driver (lower unit of the sta- sioner [12].
pler) [4] shoots stables will shift from the position where the
staple clincher (upper unit of the stapler) [5] receives sta-
[7]
ples.
[8]
[5]
[6]
[9]

[4] [11]
[10]

[12]

5) Remove the timing belt [13].


6) Remove the E-ring [14] to remove the staple position check
gear [15].

(2) Adjusting the Stapler Phase [15]

When the gears or timing belt at the front of the stapler is replaced
or removed for some reason, the staple shooting timing of the [14]
(lower unit of the stapler) does not match the staple bending timing
of the staple clincher (upper unit of the stapler). Adjust the stapler
phase following the procedure described below.

Gear [13]

7) Turn the gear [16] to align the round hole in the staple driver
gear with the round hole [17] at the back.

Timing belt

Gear [16]

[17]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 3


8) Insert a pin [18] with a diameter of approximately 2 mm 12) Mount the staple position check gear [27] so that the blue mark
(use of a 2 mm Allen wrench is recommended) in the round [25] on the staple position check gear is aligned with the round
hole to secure the gear. hole [26] in the frame.

[26]

[25]

[18]
[27]

9) Turn the gear [19] to align the round hole in the staple clincher
cam with the round hole [20] at the back.

The position where the blue mark is aligned with the round
[19] hole is the home position for stapling. If the staple jam cancel
dial is turned for some reason, the home position deviates,
making it impossible to remove the stapler cartridge. If such a
case, the gear can be returned to the home position by check-
ing blue mark position. Therefore, it is necessary to mount the
gear at the correct position.
13) Remove the pin securing the gear to the cam.
14) Assemble the spring [28], spacer [29], staple jam releasing
gear [30], timing belt [31], and relay gear [32] and secure them
with the E-ring [33].

[28]

[31]

[20]
10) Insert a pin [21] with a diameter of approximately 2 mm (use of
a 2 mm Allen wrench is recommended) in the round hole to [29]
[32]
secure the gear.

[30] [33]

(3) Adjusting the Phase of the Gear in the Saddle Unit


If the gears at the front of the saddle unit or the paper fold rollers in
the sale unit are replaced or removed for some reason, adjust the
gear phase following the procedure described below.
1) The paper fold rollers [1] and saddle cam [2] must be posi-
tioned as shown below.

[21]
11) With the gears and cam fixed, install the timing belt [22] on
gears [23] and [24]. [2]

[1]

[23]

[22]

[24]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 4


2) With the paper fold rollers and saddle cam positioned as 7) Remove the three screws [9], and slide out the stapler unit [10]
shown, mount gears as shown below. slightly to the front.
• Align the ▲ mark (either of two ▲ marks) on the saddle cam 8) Slide out the saddle unit [11] to the front.
drive gear [3] with the ▲ mark on the relay gear [4] (on the
half of the periphery where gears with a smaller face width [10] [9]
are arranged).
• With the ▲ mark on the saddle cam drive gear [3] aligned
with the ▲ mark on the relay gear [4], align the other ▲ mark
on the relay gear withy the rib of the paper folding roller drive
gear [5].

[3]

[4] [9] [11]

(5) Processing Tray Assembly


[5]
1) Remove the processing tray upper cover. (See A.(5).)
2) Remove the side guide. (See A.(7).)
3) Remove the two screws [1], and disconnect the five connec-
tors [2].

[1]
(4) Saddle Unit
1) Remove the front cover. (See A.(2).)
2) Remove the rear cover. (See A.(3).)
3) Open the jam removal cover [1]; then, remove the two screws [2]
[2] and the right stay [3].

[3]

[2]

[2] [1] [2]

4) Pull the processing stopper base [3] to the front, and free the
[2]
claw [5] at the front and the claw [6] at the rear of the process-
[1] ing stopper [4].

4) Turn the fold jam releasing dial assembly [4] to move the paper
retaining plate assembly [5] to the inside.
[6]
[5] [5]
[4] [4]

[4] [3]

5) Remove the stop ring [6], and detach the timing belt [7].
6) Disconnect the two connectors [8].

[6]

[7]

[8]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 5


5) Disconnect the three connectors [7]. (6) Paddle Assembly
6) Release the two claws [8] of the harness retainer, and detach 1) Remove the processing tray assembly. (See B.(3).)
the motor harness [9]. 2) Place the processing tray assembly [1] as shown.
NOTE: Be sure to take care not to damage the aligning plate
[2].

[1]

[9]
[2]

[8] 3) Detach the timing belt [3], and remove the two screws [4].

[7] [4]

7) Remove the stop ring [10], and detach the timing belt [11].
8) Disconnect the connector [12], and free the harness [14] from
the edge saddle [13].

[12]
[11] [14]

[3]
[10]
[13]

9) Remove the two screws [15], and slide the processing tray
assembly [16] to the rear; then lift it to detach.
[4]

4) Separate the processing tray assembly [5] and the paddle


assembly [6] as shown.

[16] [6]

[5]

[15]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 6


(7) Staple/Fold Drive Unit 10) Disconnect the two connectors [18], and free the harness [20]
1) Open the front door, and slide out the stapler unit slightly to the from the edge saddle [19].
front.
[18]

2
1
[20]

[19]
[18]

11) Remove the three screws [21].


[21]
2) Remove the screw [3], and detach the interface retainer [4].
3) Free the six harness retainers [5], and disconnect the connec-
tor [6]. [21]
4) Free the harness [7] from the harness retainer [5].
5) Free the harness [7] from the edge saddle [8]; then, disconnect
the two connectors [9].

[9]

[7] [8]

[21]

12) Remove the screw [22], and detach the staple/fold drive unit
[5] [23].
[6]
[7]
[3]
[7] [5]

[4] [5] [7] [5]

6) Release the harness retainer [10], and disconnect the connec-


tor [11]. [22]

7) Free the harness [12] from the harness retainer [10]. [23]
8) Free the harness [12] for the edge saddle [13]; and disconnect
the two connectors [14]. (8) Feed Motor Unit
1) Remove the rear cover. (See A.(3).)
[14] [11]
2) Open the harness retainer [1], and disconnect the two connec-
tors [2].
[12] 3) Remove the screw [3], and detach the harness guide [4].
4) Remove the three screws [5], and detach the feed motor unit
[10] [6].
[13]

[5]

9) Remove the screw [15], and free the claw [17] of the harness [5]
guide from the long angle [16] of the base plate. [3]

[15]

[4]
[6]

[17] [2]
[16]
[1]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 7


(9) Feed Roller 11) Remove the feed roller [12].
1) Remove the upper cover. (See A.(4).)
2) Remove the upper right cover assembly. (See A.(6).)
3) Remove the feed motor unit. (See B.(6).)
4) Remove the screw [1].
5) Remove the stop ring [2], and detach the bushing [3].

[12]

(10) Stack Delivery Roller (Upper)


1) Remove the paddle assembly. (See B.(4).)
2) Place the paddle assembly [1] as shown.

[1]

[1] [3]
[2]

6) Remove the two screws [4].

[4]
3) Turn the gear [2] in the direction of the arrow to move up the
stack delivery roller assembly (upper) [3].

[3]

7) Remove the gear [5], and detach the gear [6] while spreading
the claw.
[2]
8) Remove the stop ring [7], and detach the bushing [8].
9) Remove the screw [9], and detach the inlet sensor [10].
10) Remove the lower paper guide [11]. 4) Push up the stack delivery roller (upper) [4] from below to free
the stack deliver roller (upper) [4] from the shaft [5].

[8] [5]
[9]

[10]
[7] [6]
[11]

[4]

[5]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 8


5) Shift up the stack delivery roller (upper) [4], and then push it 5) Push up the safety guide [4] from below to free the safety
down to detach the stack deliver roller (upper) [4]. guide [4] from the shaft [5].
6) Likewise, remove the stack delivery roller (upper) [6] at the
front.
[4]

[6]
[4]

[5]

6) Remove the paddle [6] in the direction of the arrow.


7) Likewise, remove the other paddle.
(11) Paddle
1) Remove the paddle assembly. (See B.(4).) [6]
2) Place the paddle assembly [1] as shown.

[1]

(12) Stack Delivery Roller (Lower)/Delivery Belt


1) Remove paddle assembly, and separate it from the processing
tray assembly. (See B.(4).)
3) Turn the gear [2] in the direction of the arrow to move up the 2) Slide the aligning plate (front) [2] and the aligning plate (rear)
stack delivery roller assembly (upper) [3]. [3] of the processing tray assembly [1] by sliding them to the
outside.

[1]
[3]

[3]

[2]

3) Remove the processing tray stopper [4].

[4]

[2]

4) Push up the safety guide [4] from below to free one side of the
safety guide [4] from the shaft [5].

4) Remove the screw [5], and detach the paper guide (front) [7]
while freeing the two claws [6].

[5]
[7]

[6]
[5]
[4]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 9


5) Remove the screw [8]; then, while freeing the claw [9], detach C. PCBs
the paper guide (rear) [10].
(1) Finisher Controller PCB
[8] 1) Remove the rear cover. (See A.(3).)
2) Disconnect the 17 connectors [1], and remove the screw [2].
3) Free the PCB retainer [3], and detach the finisher controller
PCB [4].

[10]
[9] [2] [3]

6) Remove the two stop rings [11]; then, move the two bushings [1]
[12] to the inside. [1]
[1]

[4]

[12]
[11] (2) Slide Home Position PCB
1) Open the front door, and turn the tab [2] on the stapler slide in
the direction of the arrow to slide the stapler to the frontmost
point.
[11] 2) Remove the stapler unit. (See B.(1).)
[12]

7) Remove the four screws [13]; then, lift the stack delivery roller
assembly (lower) [14] to detach. 2

[13]

[14] [13] 3) Place the stapler unit [3] as shown.


4) Remove the two screws [4], and detach the guide [5].

8) Remove the stack delivery roller (lower) [15] and the two deliv- [3]
ery belts [16].

[16]

[4]
[5]

[4]

[15] 5) Turn the tab [2] on the stapler side in the direction of the arrow
so that that the fixing screw [7] of the slide home position PCB
[6] is in view through the round hole.
6) Remove the fixing screw [7].

NOTE: Be sure to mount them so that the edges [17] of the claws [2]
of the delivery belts are flush.

[6]
[17]

[7]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 10


7) Disconnect the connector [8]. (2) Paper transport unit exit sensor
8) Remove the flexible cable retainer [9]. 1) Remove the paper pass unit.
9) Free the lock [10] of the connector in the direction of the arrow; 2) Remove the bracket, and remove the paper transport unit exit
then, detach the flexible cable [11], and then detach the side sensor.
home position PCB [12].

[8] [10]

[11]

[6]

[9]
(3) Upper Guide Flapper
1) Remove the paper pass unit.
2. Paper Transport Section (MX-RBX1) 2) Open the upper transport unit, remove each parts, and remove
the reverse gate.
A. Paper Pass Unit
1) Pull out the paper pass unit, and remove the screw. 1

(4) Interface Fan


1) Remove the paper pass unit.
2) Remove the bottom cover.
2) Free the lock, to remove the paper pass unit.

3) Remove the clamps, and disconnect the connector then


(1) Paper transport unit entry sensor remove the interface fan.
1) Remove the paper pass unit. * Install the interface fan so as the side with the label (A)
2) Remove the paper transport unit entry sensor. comes to the direction illustrated.

2
2

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 11


(5) Interface Transport Motor * Adjust so that the distance between the lower guide and the
1) Remove the paper pass unit. upper guide flapper is 22mm with the solenoid plunger
pushed in. Install the entry reverse pass solenoid..
2) Remove the bottom cover. (See (4).)
3) Disconnect the connector, then remove the interface transport
motor. 22mm

1 2
3 (7) Entry Roller
1) Remove the paper pass unit.
2) Remove the interface transport motor. (See (4).)
3) Remove the front cover. (See (6).)
4) Remove the stopper band, and the bracket, then remove the
(6) Entry Reverse Pass Solenoid. upper guide unit.

1) Remove the paper pass unit.


1
2) Remove the bottom cover. (See (4).)
3) Remove the front cover.
3

* When installing, adjust so that the solenoid is fit with the


4) Remove the solenoid unit bracket ±adjustment reference. If the upper guide unit mag-
net lifts up, adjust the bracket for the magnet not to lift up.

1
Adjustment
reference
± 0.5

2 5) Remove each parts, then remove the entry roller.

5) Remove each parts, then remove the entry reverse pass sole-
noid.

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 12


(8) Post Entry Roller (10) Exit Roller
1) Remove the paper pass unit. 1) Remove the paper pass unit.
2) Remove the bottom cover. (See (4).) 2) Remove the bottom cover. (See (4).)
3) Remove the front cover. (See (6).) 3) Remove the front cover (See (6).)
4) Remove the upper guide unit. (See (7).) 4) Remove the upper guide unit. (See (7).)
5) Remove the bracket, and remove the post entry roller unit. 5) Remove the drawer bracket.
Remove each parts and remove the exit roller.

6) Remove each parts, and remove the post entry roller.

B. Reverse Tray Unit


(1) Reverse Flapper
1) Remove the paper pass unit.
2) Remove the reverse tray.

(9) Pre Entry Roller


1) Remove the paper pass unit.
2) Remove the bottom cover. (See (4).)
3) Remove the front cover. (See (6).) 3) Remove each parts, and remove the reverse flapper.
4) Remove the upper guide unit. (See (7).)
5) Remove each parts, and remove the pre entry roller.

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 13


C. Left Cabinet Unit (2) Paper Pass PCB
(1) Interface Transport Unit Cover Detection Sensor 1) Remove the paper pass unit.
1) Remove the paper pass unit. 2) Remove the reverse tray. (See B.(1))
2) Remove the reverse tray. (See B.(1).) 3) Remove the left cover. (See C.(1).)
3) Free the lock, then remove the saddle stitch finisher. 4) Remove allen screw, remove the interface PCB, then remove
the connector.

2 4

1
4) Remove the left cover.

3. Punch Unit (AR-PN1A/B/C/D)


A. Punch Driving System
(1) Removing the Punch Motor
1) Remove the two screws [1].
2) Disconnect the connector [2] to remove the punch motor [3].

[2]

5) Disconnect the connector, and the sensor bracket. Remove


the interface transport unit cover detection sensor.

[1] [3]

(2) Removing the Punch Horizontal Registration


Motor
1) Disconnect connector [1].
2) Remove the harness [3] from the harness guide [2].
3) Remove the two screws [4] to remove the punch horizontal
registration motor [5].

[4]

[3]

[1]

[2]
[5]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 14


(3) Removing the Punch Unit 7) Remove the screw [9] and washer [10].
1) Remove the waste case. 8) Disconnect the connector [11].
2) Remove the screw [1] to detach the jam processing cover [2]. 9) Remove the two screws [12] to detach the base cover [13].

[1] [2]

[9]

[10]

3) Disconnect the connector [3].


4) Remove the harness [5] from the harness guide [4].

[13]
[3]

[11]
[12]
[5]

[4]

5) Disconnect the connector [6].


6) Remove the screw [7] and sensor support plate [8].

[6]

10) Remove the four screws [14] to remove the upper transmission
sensor unit [15] and lower transmission sensor [16].

[15]

[8] [7]

[14] [14] [16] [14]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 15


11) Remove the punch unit [18] from the punch horizontal registra- 4) Disconnect the connector [5] to remove the photosensor PCB
tion motor assembly [17]. [6].

[17] [6]
[18]

B. PCBs [5]

(1) Punch Controller PCB


1) Remove the two screws [1]. (3) Removing the LED PCB
2) Disconnect the five connectors [2] to remove the punch con- 1) Remove the punch waste case.
troller PCB [3]. 2) Disconnect connector [1].
3) Remove the harness [3] from the harness guide [2].
[2] [3]

[2] [1]

[3]

[2]

4) Remove the screw [4] and washer [5].


[2] 5) Disconnect the connector [6].
6) Remove the screw [7] to detach the base cover [8].
[1]

(2) Horizontal Registration Photosensor PCB


1) Remove the punch motor. (See A.(1).)
2) Remove the screw [1]. [4]
3) Remove the harness [3] from the harness guide [2] on the
PCB, then detach the PCB cover [4].

[1]
[4]
[5]

[8]

[6] [7]

[3]

[2]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 16


7) Remove the screw [9].
8) Disconnect the connector [10] to remove the LED PCB [11].

[10]
[9]

[11]

(4) Waste-Full Photosensor PCB


1) Remove the punch controller PCB.
2) Remove the two screws [1] to remove the PCB film [2].

[2]

[1]
[3]

3) Disconnect the connector [3] to remove the waste-full photo-


sensor PCB [4].

[2]

[1]

(5) Waste Full LED PCB


1) Remove the screw [1].
2) Disconnect the connector [2] to remove the waste-full LED
PCB [3].

[3]

[4]

MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 17


[7] MAINTENANCE
âºíuÇ´
Service Manual

1. Maintenance System Table


✕: Check (Clean, replace, or adjust as necessary.) {: Clean ▲: Replace U: Adjust ✩: Lubricate †: Move position

Follows the cycle of the main


No. Part name When calling Remark
unit.
1 Transport rollers { {
2 Transport paper guides { {
3 Gears ✕ ✕
4 Belts ✕ ✕
5 Paddle ✕ { Replacement reference: Replace at every 1000K of
the finisher paper exit count value.
6 Sensors ✕ ✕
7 Discharge brush ✕ ✕
8 Staple unit Replacement reference: Replace the unit at every 100K staple.
9 Punch unit Replacement reference: Replace the unit at every 1000K.
10 Staple cartridge User replacement for every 5000pcs.

1 1 1 10 1 1 9 1 1 1 1 1 1 1 1

6
6
6

6
5 1 8 1 1 1 1 1 1
6

6
6
6 6
7 6 6
6 6
6 6
6
6
6 6 6
6 6
6 6
10

MX-FNX2/AR-PN1/MX-RBX1 MAINTENANCE 7 – 1
[8]
âºíuÇ´
ADJUSTMENTS 2) Adjust theManual
Service stapling position by pressing the PSW1 or PSW2 on
the finisher controller PCB a required number of times. Press-
ing the switch once moves the stapling position about 0.14
1. Finisher/saddle unit mm.
• To move the stapling position in the "-" direction, press the
A. Adjusting the Folding Position PSW1.
The folding position is adjusted by matching it with the stapling
• To move the stapling position in the "+" direction, press the
position.
PSW2.
If you have replaced the finisher controller PCB, you must transfer
• Pressing the PSW1 and PSW2 at the same time clears the
the existing settings to the new PCB. Perform the following if the
adjustment value.
folding position must be adjusted for some reason.
NOTE: Both the folding and stapling positions may deviate for
some type of paper. In such a case, change the "middle - direction + direction
stapling position" in the user mode of the host machine.
1) Set SW1 on the finisher controller PCB as follows:

ON

1 2 3 4 5 6 7 8

2) Adjust the folding position by pressing the PSW1 or PSW2 on


the finisher controller PCB a required number of times. Press-
ing the switch once moves the folding position about 0.16 mm.
• To move the folding position in the "-" direction, press the 3) When adjustment of the stapling position is complete, set all
PSW1. bits of the SW1 on the finisher controller PCB to OFF.
• To move the folding position in the "+" direction, press the 4) Enter the bind mode of the host machine and check whether
PSW2. the stapling position is adjusted properly. If adjusted improp-
erly, adjust the stapling position again.
• Pressing the PSW1 and PSW2 at the same time clears the
adjustment value. C. One-page exit mode
This mode is used to increase the accuracy of paper alignment in
the simple load offset mode by discharging paper one by one to the
- direction + direction offset tray.
1) Set the SW1 of the finisher control PWB as shown below.

ON

1 2 3 4 5 6 7 8

2) Turn on the power.

3) When adjustment of the folding position is complete, set all bits 2. Punch unit (option)
of the SW1 on the finisher controller PCB to OFF.
A. Adjusting the Punch Hole Position
4) Enter the bind mode of the host machine and check whether
the folding position is adjusted properly. If adjusted improperly, This adjustment is available only in the diagnostic mode (Sim 3-10)
adjust the folding position again. of the host machine. The range of punch hole displacement is
between 3 and -3 in 1-mm increments. A higher setting will move
B. Adjusting the Middle 2-Point Stapling Position the punch hole toward the leading edge of sheet.
The stapling position is adjusted by matching it with the folding
B. Adjusting the Sensor Output
position.
Perform the following when the punch controller PCB, horizontal
● This adjustment is necessary:
registration sensor (photosensor PCB/LED PCB), or waste full sen-
• If you have replaced the finisher controller PCB. sor (waste full photosensor PCB/waste full LED PCB) has been
• If the stapling position must be adjusted for some reason. replaced.
NOTE: Both the folding and stapling positions may deviate for 1) Shift bits 1 through 4 on the punch controller PCB as follows:
some type of paper. In such a case, change the "middle
stapling position" in the user mode of the host machine. ON
1) Set SW1 on the finisher controller PCB as follows:

ON 1 2 3 4

2) Press SW1002 or SW1003 on the punch controller PCB. A


press will automatically adjust the sensor output.
1 2 3 4 5 6 7 8
• The adjustment is over when all LEDs on the punch control-
ler PCB are ON: LED1001, LED1002, LED1003.
3) Shift all bits of DIPSW1001 to OFF.

MX-FNX2/AR-PN1/MX-RBX1 ADJUSTMENTS 8 – 1
C. Registering the Number of Punch Hole E. Setup by the diag simulation of the host
Perform the following to register the type of punch unit (number of machine
holes) used to the IC on the punch controller PCB for identification 1) Select "FINISHER ADJUSTMENT" in SIM 3-10.
by the finisher. Be sure to register the type whenever you have
2) Select a setup item and change the setup value.
replaced the punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch control- 0
ler PCB as follows: SIMULATION NO.03-10 CLOSE
TEST

ON FINISHER ADJUSTMENT
A:200 ; SADDLE POSITION
A: 200 B:200 ; FOLDING POSITION
1 2 3 4 C: 10 ; FRONT ADJUSUT
[197-203]
D:100 ; REAR ADJUSUT
2) Press SW1002 on the punch controller PCB to select the
appropriate number of punch holes. OK

• Each press on SW1002 moves the selection through the fol-


lowing (repeatedly from top to bottom).
10-key
Number of punch holes LED1001 LED1002 LED1003
OK
2 holes (Punch Unit-J1) ON OFF OFF
2/3 holes (Punch Unit-K1) ON ON OFF
4 holes (Punch Unit-G1) OFF ON OFF 0
4 holes (Punch Unit-H1) OFF OFF ON SIMULATION NO.03-10 CLOSE
TEST
3) Press SW1003 on the punch controller PCB twice. The FINISHER ADJUSTMENT
presses will store the selected number of punch holes on the A:197 ; SADDLE POSITION
punch controller PCB. A: 197 B:200 ; FOLDING POSITION
• A single press on SW1003 will cause the LED indication to C: 10 ; FRONT ADJUSUT
[197-203]
flash; another press on SW1003 will cause the indication to D:100 ; REAR ADJUSUT
remain ON to indicate the end of registration.
OK
4) Shift all bits of DIPSW1001 to OFF.

D. After Replacing the EEP-ROM (IC1002) Adjustable setup range is as follows.


1) Turn off the host machine.
Default Setup Change/Setup
2) Set bits 1 through 4 on the punch controller PCB as follows: Adjustment content
value range value 1
1 Saddle binding position 200 0 - 400 0.0707mm
ON
adjustment
2 Saddle folding position 200 0 - 400 0.0525mm
adjustment
1 2 3 4
3 Front alignment position 10 0 - 20 0.367mm
adjustment
3) Press SW1002 and SW1003 on the punch controller PCB at
4 Rear alignment position 10 0 - 20 0.367mm
the same time. adjustment
• The presses will initialize the EEP-ROM. At the end, all 5 Staple front one-position 100 0 - 200 0.04374mm
LEDs (LED1001, LED1002, LED1003) will go ON. binding position adjustment
4) Adjust the sensor output, and store the number of punch 6 Staple rear one-position 100 0 - 200 0.04374mm
holes. Adjust the punch hole position adjustment (horizontal binding position adjustment
registration) of necessary. 7 Staple 2-position binding 100 0 - 200 0.04374mm
center adjustment
8 Staple 2-position binding 50 0 - 100 0.04374mm
pitch adjustment
9 Punch center position 50 47 - 53
adjustment (FR direction)
10 Punch hole position 50 0 - 100 0.105mm
adjustment (paper feed
direction)

MX-FNX2/AR-PN1/MX-RBX1 ADJUSTMENTS 8 – 2
[9]
âºíuÇ´
SELF DIAG MESSAGE AND TROUBLE CODE
Service Manual

1. Self diag message


A. Saddle Finisher unit
Error Condition Timing of detection Operation Resetting
Stapler absent The stapler is not set. Monitoring at all times The staple motor (FFSM) and the staple Set the stapler.
shift motor (FSM) will stop.
Staple absent The staple cartridge has run out of Monitoring at all times Normal operation will continue; however, Replace the staple
staples. operation is subject to instructions from cartridge; or, set it
the host machine. correctly.
Mixed sheets Sheets of different sizes are deposited When a sheet of a different The sheet will be aligned based on –
in the compartment. size is placed. maximum size width and delivered as a
stack.
Overstacking for The number of sheets in the When an extra sheet is The sheets will be delivered with stapling. –
stapling compartment has exceeded the limit placed.
imposed on stapling.
Stack tray The number of sheets deposited on the When an extra sheet is Normal operation will continue. Remove the sheets
overstacking delivery tray has exceeded the limit placed. from the delivery tray.
imposed on the tray (sheets, sets).
Saddle Remove the stack from the bind tray. When an extra sheet is Normal operation will continue. Remove the stack from
overstacking More than 10 stacks are deposited on placed. the bind tray.
the folded stack tray.

B. Punch Unit (option)


Error Condition Timing of detection Operation Resetting
Waste case full The amount of waste paper in the waste During punching. Normal operation will continue. Remove the waste
case has reached the limit. paper from the waste
case.
Excess water The amount of waste paper in the waste During punching. Punching will be disabled. Remove the waste
case has exceeded the limit. paper from the water
case.

2. Trouble code
A. Outline
The CPU on the machine's finisher controller PCB is equipped with a mechanism to check the machine condition as needed; when it detects a
fault, the machine communicates the fact to the host machine in the form of a code and a detail code.
The host machine indicates the code on its control panel.

B. Trouble code

F1-00 Console finisher communication trou- F1-02 Console finisher transport motor
ble abnormality
Content Console finisher communication trouble Content Console finisher transport motor abnormality
Phenomenon Detail Communication cable test error after turning Phenomenon Detail Transport motor trouble
on the power or exiting from DIAG. Case Cause Motor lock
Communication error with the console Motor rpm abnormality
finisher Overcurrent to the motor
Case Cause Improper connection or disconnection of Console finisher control PCB trouble
connector and harness between the Check and Use DIAG (SIM3-3) to check the motor
machine and the console finisher. remedy operation.
Console finisher control PCB trouble
Control PCB (PCU) trouble
Malfunction due to electrical noise F1-03 Console finisher paddle motor (FPM)
Check and Canceled by turning OFF/ON the power.
remedy Check connectors and harness in the
trouble
communication line.
Content Console finisher paddle motor (FPM) trouble
Replace the console finisher control PCB or
Phenomenon Detail Paddle motor (FPM) operation abnormality
PCU PCB.
Case Cause Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PCB trouble
Check and Use DIAG (SIM3-3) to check the motor
remedy operation.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 1


F1-08 Console finisher staple shift motor F1-20 Console finisher alignment motor
(FSM) trouble (rear) (FRJM) trouble
Content Console finisher alignment motor (rear) (FRJM) trouble
Content Console finisher staple shift motor (FSM) trouble
Phenomenon Detail Alignment motor (rear) (FRJM) operation
Phenomenon Detail Staple shift motor (FSM) operation
abnormality
abnormality
Case Cause Motor lock
Case Cause Motor lock
Motor rpm abnormality
Motor rpm abnormality
Overcurrent to the motor
Overcurrent to the motor
Console finisher control PCB trouble
Console finisher control PCB trouble
Check and Use DIAG (SIM3-3) to check the motor
Check and Use DIAG (SIM3-3) to check the motor
remedy operation.
remedy operation.

F1-10 Console finisher stapler motor (FFSM) F1-21 Interface fan (FJFM) trouble
trouble Content Interface fan (FJFM) trouble
Phenomenon Detail Interface fan (FJFM) drive trouble
Content Console finisher stapler motor (FFSM) trouble
Case Cause Missing the motor lock and the connector
Phenomenon Detail Stapler motor (FFSM) operation abnormality Check and Use DIAG (SIM3-3) to check the motor
Case Cause Motor lock remedy operation.
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PCB trouble
F1-31 Console finisher bookbinding position
Check and Use DIAG (SIM3-3) to check the motor
remedy operation. sensor (FFPD) trouble
Content Console finisher bookbinding position sensor (FFPD)
trouble
F1-11 Console finisher bundle exit motor Phenomenon Detail Sensor input value abnormality
(FAM) trouble Case Cause Sensor breakage harness breakage
Console finisher control PCB trouble
Content Console finisher bundle exit motor (FAM) trouble
Check and Use DIAG (SIM3-2) to check the sensor
Phenomenon Detail Bundle exit motor (FAM) operation remedy operation.
abnormality
Case Cause Motor lock
Motor rpm abnormality
Overcurrent to the motor
F1-32 Communication trouble between the
Console finisher control PCB trouble console finisher and the punch unit
Check and Use DIAG (SIM3-3) to check the motor (AR-PN1A/B/C/D).
remedy operation.
Content Communication trouble between the console finisher and
the punch unit (AR-PN1A/B/C/D).
F1-15 Console finisher lift motor (FLM) trou- Phenomenon Detail Communication error between the console
finisher and the punch unit (AR-PN1A/B/C/
ble D).
Content Console finisher lift motor (FLM) trouble Case Cause Improper connection or disconnection of
Phenomenon Detail Lift motor (FLM) operation abnormality connector and harness between the console
finisher and the punch unit.
Case Cause Motor lock
Console finisher control PCB trouble
Motor rpm abnormality
Control PCB (PCU) trouble
Overcurrent to the motor
Malfunction by noise
Console finisher control PCB trouble
Check and Canceled by turning OFF/ON the power.
Check and Use DIAG (SIM3-3) to check the motor
remedy Check connectors and harness in the
remedy operation.
communication line.
Replace the console finisher control PCB.

F1-19 Console finisher alignment motor


(front) (FFJM) trouble F1-33 Console finisher punch side registra-
Content Console finisher alignment motor (front) (FFJM) trouble tion motor (FPSM) trouble (AR-PN1A/
Phenomenon Detail Alignment motor (front) (FFJM) operation B/C/D)
abnormality
Case Cause Motor lock Content Console finisher punch side registration motor (FPSM)
Motor rpm abnormality trouble (AR-PN1A/B/C/D)
Overcurrent to the motor Phenomenon Detail Punch side registration motor (FPSM)
Console finisher control PCB trouble operation abnormality
Check and Use DIAG (SIM3-3) to check the motor Case Cause Motor lock
remedy operation. Motor rpm abnormality
Overcurrent to the motor
Console finisher control PCB trouble
Check and Use DIAG (SIM3-3) to check the motor
remedy operation.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 2


F1-34 Console finisher punch motor (FPNM) F1-39 Console finisher punch dust sensor
trouble (AR-PN1A/B/C/D) trouble (AR-PN1A/B/C/D)
Content Console finisher punch motor (FPNM) trouble
Content Console finisher punch dust sensor trouble
(AR-PN1A/B/C/D)
(AR-PN1A/B/C/D)
Phenomenon Detail Punch motor (FPNM) operation abnormality
Phenomenon Detail Sensor input abnormality
Case Cause Motor lock
Case Cause Dust sensor breakage harness
Motor rpm abnormality
disconnection console finisher control PCB
Overcurrent to the motor
trouble
Console finisher control PCB trouble
Check and Use DIAG (SIM3-2) to check the sensor
Check and Use DIAG (SIM3-3) to check the motor
remedy operation.
remedy operation.

F1-35 Console finisher punch side registra- F1-40 Console finisher puncher section
tion home position (FPSHPD) trouble power trouble (AR-PN1A/B/C/D)
(AR-PN1A/B/C/D) Content Console finisher puncher section power trouble
(AR-PN1A/B/C/D)
Content Console finisher punch side registration home position Phenomenon Detail Puncher operation abnormality
(FPSHPD) trouble (AR-PN1A/B/C/D) Case Cause Punch control PCB trouble
Phenomenon Detail Sensor input value abnormality Check and Replace the punch control PCB
Case Cause Sensor breakage remedy
Harness disconnection
Console finisher control PCB trouble
Check and Use DIAG (SIM3-2) to check the sensor
remedy operation.

F1-36 Console finisher punch side registra-


tion detect (FPTD, FPSD) trouble (AR-
PN1A/B/C/D)
Content Console finisher punch side registration detect (FPTD,
FPSD) trouble (AR-PN1A/B/C/D)
Phenomenon Detail Sensor input value abnormality
Case Cause Sensor breakage
Harness disconnection
Console finisher control PCB trouble
Check and Use DIAG (SIM3-2) to check the sensor
remedy operation.

F1-37 Console finisher backup RAM data


trouble
Content Console finisher backup RAM data trouble
Phenomenon Detail Backup RAM contents are disturbed.
Case Cause Console finisher control PCB trouble
Malfunction by noise
Check and Replace the console finisher control PCB.
remedy

F1-38 Console finisher punch backup RAM


data trouble (AR-PN1A/B/C/D)
Content Console finisher punch backup RAM data trouble (AR-
PN1A/B/C/D)
Phenomenon Detail Punch unit backup RAM contents are
disturbed.
Case Cause Punch control PCB trouble
Malfunction by noise
Check and Replace the punch control PCB.
remedy

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 3


C. Troubleshooting
(1) Finisher/saddle unit

a. F1-03, Paddle Motor (FPM) Fault

Cause/Trouble section Procedure Check Result Remedy


Paddle home position sensor (FPDHPD) 1 Check the paddle home position sensor (FPDHPD). NO Replace the sensor
Is the sensor normal?
Stack roller home position sensor 2 Check the stack roller home position sensor (FPDHPD). NO Replace the sensor.
(FARHPD) Is the sensor normal?
Wiring 3 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
paddle motor (FPM) normal?
Paddle, Swing guide assembly 4 Try turning the paddle motor (FPM) clockwise and YES Correct the mechanical
counterclockwise by hands. Is there mechanical tapping in mechanism.
the rotation of the paddle or the up/down movement of the
swing guide?
Paddle motor (FPM), finisher controller 5 Try replacing the paddle motor (FPM). Is the problem YES Replace the finisher controller
PCB corrected? PCB.

b. F1-06, Slide Staple Motor (FSM) Fault

Cause/Trouble section Procedure Check Result Remedy


staple shift home position sensor 1 Check the staple shift home position sensor (FSTHPD). NO Replace the sensor.
(FSTHPD) Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
staple shift motor (FSM) normal?
Stapler unit 3 Is there mechanical trapping in the stapler path? YES Correct the mechanical
system.
Slide slide motor (FSM), Finisher 4 Try replacing the staple shift motor (FSM). YES End.
controller PCB Is the problem corrected? NO Replace the finisher
controller PCB.

c. F1-10, Staple Motor (FFSM) Fault

Cause/Trouble section Procedure Check Result Remedy


Staple drive home position sensor 1 Check the staple drive home position sensor (FSHRD). Is NO Replace the sensor
(FSHPD) the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
staple motor (FFSM) normal?
Stapler unit 3 Try turning the staple jam releasing dial. YES Correct the mechanical
Is there mechanical trapping? system.
Staple motor (FFSM), Finisher controller 4 Try replacing the staple motor (FFSM). Is the problem YES End.
PCB corrected? NO Replace the finisher
controller PCB.

d. F1-10, Staple Motor (FFSM) Fault

Cause/Trouble section Procedure Check Result Remedy


Bookbinding home position sensor 1 Check the bookbinding home position sensor (FFHPD). NO Replace the sensor.
(FFHPD) Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
staple motor (FFSM) normal?
Saddle unit 3 Try turning the fold jam releasing dial. YES Correct the mechanical
Is there mechanical trapping? mechanism.
Staple motor (FFSM), Finisher controller 4 Try replacing the staple motor (FFSM). Is the problem YES End.
PCB corrected? NO Replace the finisher
controller PCB.

e. F1-10, Staple Motor (FFSM) Fault

Cause/Trouble section Procedure Check Result Remedy


Bookbinding lock sensor (FFE) 1 Check the bookbinding lock sensor (FFE). NO Replace the sensor.
Is the sensor normal?
Finisher controller PCB, Saddle unit 2 Does the staple motor (FFSM) operate at the appropriate YES Replace the finisher
timing? controller PCB.
NO Check the saddle unit drive
mechanism:
if faulty, correct it;
otherwise, go to step 3).
Staple motor (FFSM), Finisher controller 3 Try replacing the staple motor (FFSM). Is the problem YES End.
PCB corrected? NO Replace the finisher
controller PCB.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 4


f. F1-11, Stack Delivery Motor (FAM) Fault

Cause/Trouble section Procedure Check Result Remedy


Delivery belt home position sensor 1 Check the delivery belt home position sensor (FOBHPD). NO Replace the sensor.
(FOBHPD) Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
stack delivery motor (FAM) normal?
Stack delivery roller 3 Try turning the stack delivery motor (FAM) by hand. NO Correct the mechanical
Is the rotation smooth? system.
Stack delivery motor (FAM), Finisher 4 Try replacing the stack delivery motor (FAM). YES End.
controller PCB Is the problem corrected? NO Replace the finisher
controller PCB.

g. F1-15, Lift Motor (FLM) Fault

Cause/Trouble section Procedure Check Result Remedy


Paper surface sensor (FSLD) 1 Check the paper surface sensor (FSLD). NO Replace the sensor.
Is the sensor normal?
Tray up/down mechanism 2 Check the tray up/down mechanism. Is the mechanism NO Correct the mechanism.
normal?
Finisher controller PCB 3 Is 24 VDC supplied from the finisher controller PCB to the lift NO Replace the finisher
motor (FLM) as soon as the tray is driven? controller PCB.
Lift motor (FLM), Wiring 4 Check the wiring from the finisher controller PCB to the lift YES Replace the lift motor (FLM).
motor (FLM); is it normal? NO Correct the wiring.

h. F1-15, Lift Motor (FLM) Fault

Cause/Trouble section Procedure Check Result Remedy


Tray position 1 Is the tray as far as the lift upper limit sensor (FULD)? YES Lower the position of the
tray.
Lift upper limit sensor (FULD) 2 Check the lift upper limit sensor (FULD). Is the sensor NO Replace the sensor.
normal?
Finisher controller PCB, Wiring 3 Check the wiring from the finisher controller PCB to the lift YES Replace the finisher
upper limit sensor (FULD); is it normal? controller PCB.
NO Correct the wiring.

i. F1-15, Shift Motor (FLM) Fault

Cause/Trouble section Procedure Check Result Remedy


- 1 Is the tray in UP position? YES Go to step 4).
NO Go to step 2).
Finisher controller PCB 2 Is power supplied to the finisher controller PCB as soon as YES Go to step 3).
the tray is driven? NO Replace the finisher
controller PCB.
Tray up/down mechanism, lift motor 3 Is there a fault in the tray up/down mechanism? YES Correct the tray up/down
(FLM) mechanism.
NO Replace the tray up/down
motor.
Lift motor lock (FLE), Finisher controller 4 Check the lift motor lock sensor (FLE). YES Replace the finisher
PCB Is the sensor normal? controller PCB.
NO Replace the sensor.

j. F1-19, Alignment Motor (front) Fault

Cause/Trouble section Procedure Check Result Remedy


Alignment plate home position sensor 1 Check the alignment home position sensor (front; FFJHPD). NO Replace the sensor.
(front; FFJHPD) Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
alignment plate motor (front; FFJM) normal?
Alignment plate (front) 3 Is there mechanical trapping in the alignment plate path? YES Correct the mechanical
system.
Alignment motor (front; FFJM), Finisher 4 Try replacing the alignment motor (front; FFJM). YES End.
controller PCB Is the problem corrected? NO Replace the finisher
controller PCB.

k. F1-20, Alignment Motor (Rear; FRJM) Fault

Cause/Trouble section Procedure Check Result Remedy


Alignment home position sensor (rear; 1 Check the alignment home position sensor (rear; FRJHPD). NO Replace the sensor.
FRJHPD) Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
alignment motor (rear; FRJM) normal?
Alignment plate (rear) 3 Is there mechanical trapping in the path of the alignment YES Correct the mechanical
plate? mechanism.
Alignment motor (rear; FRJM), Finisher 4 Try replacing the alignment motor (rear; FRJM). YES End.
controller PCB Is the problem corrected? NO Replace the finisher controller
PCB.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 5


l. F1-30, Communication error

Cause/Trouble section Procedure Check Result Remedy


Finisher controller PCB, Host machine 1 Turn off and then on the host machine. Is the problem YES End.
DC controller PCB corrected?
Wiring 2 Is the wiring between the finisher controller PCB and the DC NO Correct the wring.
controller PCB of the host machine normal?
Finisher controller PCB, Host machine 3 Try replacing the finisher controller PCB and the host YES End.
DC controller PCB machine DC controller PCB. Is the problem corrected?

m. F1-37, Finisher Unit Back-Up RAM Fault

Cause/Trouble section Procedure Check Result Remedy


Finisher controller PCB 1 Turn off and then on the host machine. Is the problem YES End.
corrected? NO Replace the finisher controller
PCB.

n. F1-80, Finisher Unit Power Supply Fault

Cause/Trouble section Procedure Check Result Remedy


Finisher controller PCB, Host machine 1 Turn off and then on the host machine. Is the problem YES End.
DC controller PCB corrected?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
host machine DC controller PCB normal?
Power supply 3 Measure the voltage between CN1-1 (+) and CN1-3 (-)/CN2- YES Replace the finisher controller
1 (+) and CN2-3 (-) on the finisher controller PCB. Is it 24 PCB.
VDC? NO Replace the host machine
DC controller PCB.

o. F1-81, Feed Motor (FFM) Fault

Cause/Trouble section Procedure Check Result Remedy


Bookbinding roller home position 1 Check the bookbinding roller home position sensor NO Replace the sensor.
sensor (FFRHPD) (FFRHPD).
Is it normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
feed motor (FFM) normal?
Feed roller 3 Try turning the stack feed roller (upper) shaft by hand. NO Correct the mechanical
Does the stack feed roller (upper) move up/down normally? system.
Feed motor (FFM), Finisher controller 4 Try replacing the feed motor (FFM). Is the problem YES End.
PCB corrected? NO Replace the finisher controller
PCB.
(2) Punch Unit, option

a. F1-32, Communication Faulty

Cause/Trouble section Procedure Check Result Remedy


Finisher controller PCB, Punch 1 Turn off and the on the host machine. Is the problem YES End.
controller PCB corrected?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
punch controller PCB normal?
Power supply 3 Measure the voltage between CN14-5 (+) and CN14-3 (-) on NO Replace the finisher controller
the finisher controller PCB. Is it 24 VDC? PCB.
YES Replace the punch controller
PCB.

b. F1-33, Punch Horizontal Registration Motor (FPSM) Fault

Cause/Trouble section Procedure Check Result Remedy


Punch horizontal registration home 1 Check the punch horizontal registration home position NO Replace the sensor.
position sensor (FPSHPD) sensor (FPSHPD).
Is the sensor normal?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
punch horizontal registration home position sensor
(FPSHPD) normal?
Horizontal registration mechanism, 3 Is there a fault in the horizontal registration mechanism? YES Correct the horizontal
punch horizontal registration motor registration mechanism.
(FPSM) NO Replace the punch horizontal
registration motor (FPNM).
Punch controller PCB, Finisher 4 Try replacing the punch controller PCB. Is the problem YES End.
controller PCB corrected? NO Replace the finisher
controller PCB.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 6


c. F1-34, Punch Motor (FPNM) Fault

Cause/Trouble section Procedure Check Result Remedy


Punch home position sensor (FPHPD) 1 Check the punch home position sensor (FPHPD). NO Replace the sensor.
Is the sensor normal?
Punch motor lock sensor (FPMCK) 2 Check the punch motor lock sensor (FPMCK). Is the sensor NO Replace the sensor.
normal?
Wiring 3 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
sensor normal?
Punch mechanism, Punch motor 4 Is there a fault in the punch mechanism? YES Correct the punch
(FPNM) mechanism.
NO Replace the punch motor
(FPNM).
Punch controller PCB, Finisher 5 Try replacing the punch controller PCB. Is the problem YES End.
controller PCB corrected? NO Replace the fisher controller
PCB.

d. F1-35, Punch Horizontal Registration Home Position Sensor (FPSHPD) Fault

Cause/Trouble section Procedure Check Result Remedy


Horizontal registration sensor 1 Check the horizontal registration sensor. Is the sensor NO Replace the sensor.
(photosensor PCB/LED PCB) normal?
Wiring 2 Check the punch motor lock sensor (FPMCK). NO Correct the wiring.
Is the sensor normal?
Punch controller PCB, Finisher 3 Try replacing the punch controller PCB. Is the problem YES End.
controller PCB correct? NO Replace the finisher
controller PCB.

e. F1-38, Punch Unit Back-UP RAM Fault

Cause/Trouble section Procedure Check Result Remedy


Punch controller PCB 1 Turn off and the on the host machine. Is the problem YES End.
corrected? NO Replace the punch controller
PCB.

f. F1-39, Waste Full Sensor Fault

Cause/Trouble section Procedure Check Result Remedy


Waste full Sensor (waste full 1 Check the waste full sensor. Is the sensor normal? NO Replace the sensor.
photosensor PCB/waste full LED PCB)
Wiring 2 Is the wiring between the punch controller PCB and the NO Correct the wiring.
waste full sensor normal?
Punch controller PCB, Finisher 3 Try replacing the punch controller PCB. Is the problem YES End.
controller PCB corrected? NO Replace the finisher controller
PCB.

g. F1-40, Punch Unit Power Supply Fault

Cause/Trouble section Procedure Check Result Remedy


Finisher controller PCB, Host machine 1 Turn off and then off the host machine. Is the problem YES End.
DC controller PCB corrected?
Wiring 2 Is the wiring between the finisher controller PCB and the NO Correct the wiring.
punch controller PCB normal?
Power supply 3 Measure the voltage between CN14-5 (+) and CN4-3 (-) on YES Replace the punch controller
the finisher controller PCB. Is it 24 VDC? PCB.
NO Replace the finisher controller
PCB.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 7


(3) Paper pass (Paper transport section)

a. The transport motor (FFM) does not operate. c. A paper jam occurs in the entry port of the interface
transport unit.
Case 1 Cause Connector pin loose connection
Check & Check connection of the connectors. Case 1 Cause Flapper solenoid connector pin loose connection
Remedy (CN309, CN307, CN306, CN303, CN301, CN21) Check & Check connection of the connectors.
Case 2 Cause Harness disconnection Remedy (CN312, CN307, CN306, CN304, CN301, CN22,
Check & Execute the conduction test between connectors. If CN23)
Remedy disconnection is found, replace the defective Case 2 Cause Harness disconnection
connectors. Check & Execute the conduction test between connectors. If
Case 3 Cause Motor lead breaking Remedy disconnection is found, replace the defective
Check & Execute the conduction test of coil. If disconnection connectors.
Remedy is found, replace the coil. Case 3 Cause Flapper solenoid trouble
Case 4 Cause Control PWB trouble Check & If there is no conduction between CN312 1 pin and
Check & If the motor does not operate in the motor Remedy 2pin, replace the solenoid.
Remedy individual operation mode, replace the control Case 4 Cause Control PWB trouble
PWB. Check & If the flapper does not operate in the individual
Remedy operation mode, replace the control PWB.
b. A fan motor alarm is generated.
d. The interface unit paper jam display is made on the system
Case 1 Cause Pinching display.
Check & Visually check the suction port and remove foreign
Remedy materials. Case 1 Cause Paper jam
Case 2 Cause Connector pin loose connection Check & Visually check to remove paper jam.
Check & Check connection of the connectors. Remedy
Remedy (CN313, CN307, CN306, CN304, CN301, CN22, Cause Sensor connector pin loose connection
CN23) Check & Check connection of the connectors.
Case 3 Cause Harness disconnection Remedy (CN310, CN311, CN307, CN306, CN304, CN301,
Check & Execute the conduction test between connectors. If CN22, CN23)
Remedy disconnection is found, replace the defective Case 2 Cause Harness disconnection
connectors. Check & Execute the conduction test between connectors. If
Case 4 Cause Motor trouble Remedy disconnection is found, replace the defective
Check & If the motor does not operate in the motor connectors.
Remedy individual operation mode, replace the motor. Cause Sensor trouble
Case 5 Cause Control PWB trouble Check & Replace the sensor at the paper jam position.
Check & If the motor does not operate in the motor Remedy
Remedy individual operation mode, replace the control Case 3 Cause Sensor flag operation trouble
PWB. Check & Visually check the sensor flag operation. If it is
Remedy caught in the operation, replace the sensor flag.
Case 4 Cause Control PWB trouble
Check & If the sensor level varies but the phenomenon
Remedy remains when each sensor is turned ON/OFF,
replace the control PWB.

MX-FNX2/AR-PN1/MX-RBX1 SELF DIAG MESSAGE AND TROUBLE CODE 9 – 8


[10]
âºíuÇ´
ELECTRICAL SECTION Service Manual

1. Block diagram
A. MX-FNX2

Txd +24V
Communication
Rxd circuit Driver
circuit FFSM
DTR
DSR DC24V
Reset DC24V
DC5V
DC24V FFM
DC5V

Host machine CPU

FPM
FJSW

FFDDW SW open/
close
detection
FSSSW circuit Expansion ROM FAM
port
+24V
Driver
EEPROM circuit
FED FFJM
Control section
FPHPD

FARHPD FRJM

FFJHPD

FRJHPD FLM

FAD

FOBHPD

FBED FSM

FSLD
FSHPD
Sensor
FFPD input FSTHPD
circuit Sensor
FFHPD input
circuit FSPD
FFRHPD
FSD
FFED
Stapler
FFE

FULD Punch communication


circuit
FLLD
DC5V DC24V
FLE Punch

FFDD

FCD

Driver
circuit

Paper pass
Sensor input
circuit
PBA-CONT-JPT
Finisher

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 1


B. MX-RBX1

RIM

Control
section

Driver
circuit RFM

Fan alarm circuit

RFSL

FJPID
Sensor/Alarm
input circuit
FJPOD

DC5V DC24V DC24V


FJPDD
DC5V

PBA-CONT-JPT

Finisher

PBA-RELAY

Paper pass

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 2


2. Wiring diagram
A. MX-FNX2

8 7 6 5

MX-FNX2

To Paper Pass

(FFJHPD)

(FCD)

(FFDD)

(FAD)

C
(FOBHPD)

(FBED)

(FSLD)

(FRJHPD)

(FFPD)

(FFHPD)

(FFRHPD)

B
(FED)

(FFED)

(FLE)
Lift lock sensor

(FLLD)
Lift lower limit sensor

(FULD)
Lift upper limit sensor

(FPDHPD)

A (FFE)
Bookbinding lock sensor

(FARHPD)

(FMLD)
Tray middle sensor

8 7 6 5

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 3


4 3 2 1

1/1

(FFM) D

(FPM)

(FAM)
Bundle exit motor

(FFJM)
Alignment motor (front)

C
(FRJM)
Alignment motor (rear)

(FSSSW)

(FFDDW)

(FJSW)

(FLM)
Lift motor

(FFSM)
Stapler motor B
(FCC)
Bookbinding clutch

(FSHPD)
Staple drive
home position sensor

(FSTHPD)
Staple slide
home position sensor

(FSD)

(FSM)
Staple shift motor

(FSPD)

4 3 2 1

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 4


B. MX-RBX1

8 7 6 5

MX-RBX1

8 7 6 5

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 5


4 3 2 1

1/1

RELAY FEED UNIT COVER SENSOR


(FJPDD)
D

RELAY FEED MOTOR (FJPM)

RELAY FEED UNIT EXIT SENSOR


(FJPOD) C

RELAY FEED UNIT ENTRANCE


(FJPID)

ENTRANCE REVERSE PASS


SOLENOID (FINRPS)

B
REKAT FAN (FJFM)

4 3 2 1

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 6


8 7 6 5 4 3 2 1

AR-PN1A/B/C/D 1/1
J2011 J2011
J1007-13
1 1
J1007-12
2 2
J1007-11
3 3 Photosensor
J1007-10
4 4 circuit PCB
J1007-9
5 5
J1007-8
6 6
D J1007-7 D
7 7
C. AR-PN1A/B/C/D

J2010 J2010
J1007-6
1 1
J1007-5
2 2
J1007-4

J2011-1
J2011-2
J2011-3
J2011-4
J2011-5
J2011-6
J2011-7
J2010-1
J2010-2
J2010-3
J2010-4
J2010-5
J2010-6
3 3 LED circuit PCB
J1007-3
4 4
J1007-2
5 5
J1007-1
6 6

9
8
7
6
5
4
3
2
1

11
J1007

13
12
10
9
8
7
6
5
4
3
2
1

11

13
12
10
J1007

J1005 J1005 J2006 J2006


Waste full
1 1
photosensor
4 4
3 3 2 2 circuit PCB
2 2
1 1

J2005 J2005 Waste full LED


C 1 1 circuit PCB C
2 2

J2009
1 1 FPMCK
2 2
Punch motor
3 3
J1006 J1006 lock sensor
9 9
8 8
7 7 J2008
Punch controller PCB 6 6 1 1
FPHPD
5 5 2 2
Punch home position
CN12 CN12 4 4 3 3 sensor
3 3
10 10
2 2
9 9
1 1
8 8 J2007
7 7 1 1
6 6 FPSHPD
2 2
5 5 Punch horizontal registration
3 3
4 4 home position sensor
3 3
B 2 2 B
J1001 J1001 J2001
1 1
5 5 1
Finisher section 4 4 2 FPSM
M

3 3 3 Punch horizontal registration


CN14 CN14 2 2 4 motor
1 1
5 5
4 4

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 7


3 3 J1002 J1002 J2002
2 2 1 1 1 FPNM
M

1 1 2 2 2 Punch motor
5
4
3
2
1

1
2
3
4
5
6
7
8
9

J1003 J1004
10
5
4
3
2
1

1
2
3
4
5
6
7
8
9
10

J2003 J2004

A A

8 7 6 5 4 3 2 1
3. LEDs and Check Pins by PCB
Of the LEDs and check pins used in the machine, those needed
during servicing in the field are discussed.
NOTE: Do not touch the check pins not found in the list herein.
They are exclusively for factory use, and require special
tools and a high degree of accuracy

A. Finisher Controller PCB

6 1 1 6
1 2 1 12 1 10 CN13
CN8 4 1 CN10
CN6 CN18 CN3
5

1
CN7
CN1

CB1

7
9
1
5

CN4
CN14

1
CN22 CN21
1

1
1 4
1

15
CN23

4
CN2

CN5
3
18

1
CN12

3
CN19

LED2 LED1

1
18

1
1 5

12
1

CN15

PSW2 PSW1
CN20
CN16

CN17 SW1
34

17

6 CN11
12

1 CN9 7 1
1 9

Switch Description
SW1 Folding position adjustment, middle 2-point stapling
adjustment etc.
PSW1 Folding position adjustment, middle 2-point stapling
adjustment etc.
PSW2 Folding position adjustment, middle 2-point stapling
adjustment etc.

B. Punch Controller PCB

13 1
4

J1007
J1005
91
J1006

SW1001
51
J1001

SW1002
SW1003
1 1

LED1001
J1002

LED1002
LED1003
2

J1003 J1004
1 10 1 5

Switch Description
SW1001 Punch hole count registration/sensor output adjustment etc.
SW1002 Punch hole count registration/sensor output adjustment etc.
SW1003 Punch hole count registration/sensor output adjustment etc.

MX-FNX2/AR-PN1/MX-RBX1 ELECTRICAL SECTION 10 – 8


Memo
PARTS GUIDE

レーザープリンタ オプション
フィニッシャー / パンチユニット
LASER PRINTER OPTIONS
MX-FNX2
FINISHER / PUNCH UNIT
AR-PN1A / AR-PN1B
AR-PN1C / AR-PN1D
MX-FNX2
MODEL MX-RBX1
AR-PN1
MODEL MX-RBX1
このパーツガイドに掲載されている表示価格ランクは消費税抜きです。

CONTENTS
1 取り付けキット (Mounting Hardware) M 梱包 & 付属品
2 外装カバー (Exterial Covers,Panels etc.) (Packing Material & Accessories)

3 本体機械内部 1(Internal Components 1) N 梱包 & 付属品


(Packing Material & Accessories)
4 本体機械内部 2(Internal Components 2) [AR-PN1]
5 パンチャ部 (Puncher Assembly)[AR-PN1] O DC コントローラー回路基板
6 パンチャトータル部 (DC CONTROLLER PCB ASSEMBLY)
(Puncher Total Assembly)[AR-PN1]
P 前カバーユニット
7 スタックモーター駆動部 (FRONT COVER UNIT)[MX-RBX1]
(Stack Motor Driver Assembly)
Q 搬送部 No1
8 駆動部 (Drive Assembly) (TRANSPORT SECTION No.1)[MX-RBX1]
9 束線押えカバー部 R 搬送部 No2
(Bundle Support Cover Assembly) (TRANSPORT SECTION No.2)[MX-RBX1]
F 処理部 (Dispose Assembly) S 搬送部 No3
G 搬送部 (Paper Feeder Assembly) (TRANSPORT SECTION No.3)[MX-RBX1]
H 折り部 1/3(Fold Assembly 1/3) T 排紙トレイ & レール部
(DELIVERY PAPER TRAY & RAIL SECTION)
I 折り部 2/3(Fold Assembly 2/3)
[MX-RBX1]
J 折り部 3/3(Fold Assembly 3/3)
U 梱包 & 付属品
K ステイプル部 1/2(Staple Assembly 1/2) (PACKING MATERIAL & ACCESSORIES)
L ステイプル部 2/2(Staple Assembly 2/2) [MX-RBX1]
■ 索引 (Index)
補修部品のランク付
市場における補修部品の在庫管理が、適正に運営出来る手助けとなることを、目的とします。
Aランク : メンテナンスパーツ、メンテナンスパーツには入っていないがメンテナンスパーツに近い消耗パーツ。
Bランク : 性能・機能パーツ(センサー、クラッチ等の電気パーツ)、消耗パーツ。
Eランク : 基板含むユニットパーツ。
Dランク : 整備パーツ(外装、パッキング、同梱パーツ)。
Cランク : 上記ランク以外のパーツ(基板の子部品を除いたもの)

DEFINITION
Rank A : Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts
Rank B : Performance/function parts (sensors, clutches, and other electrical parts), consumable parts
Rank E : Unit parts including PWB
Rank D : Preparation parts (External fitting, packing, parts packed together)
Rank C : Parts other than the above (excluding sub components of PWB)
安全性・信頼性確保のため部品は、必ず正規のものをご使用下さい。
! 印の商品は、安全上重要な部品です。交換をする時は、安全及び性能維持のため必ず指定の部品をご使用下さい。
Because parts marked with "!" is indispensable for the machine safety maintenance and operation, it must be replaced with
the parts specific to the product specification.
F 当モデルのサービス資料には、この資料以外にサービスマニュアル ( 回路図含む ) があります。合わせてご利用下さい。
F Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model.
F Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order.
F For U.S. only-Use order codes provided in advertising literature. Do not order from parts department.

1 取り付けキット (Mounting Hardware)


PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A18928000 BD GN C BASE ベース
4 0CW4144P004// BA FX N C STAND FOOT スタンド足
6 0CW4A18919000 AN EG C CASTER BRACKET キャスターブラケット
9 0CW4B10389000 AU EZ C STAY ステー
10 0CW4144K100// BK HC N C FRAME フレーム
11 0CW4A18920000 AH DX C BRACKET PIN ブラケットピン
14 0CW4144P253// BC GD N D FOOT COVER 足カバー
20 0CW4B10391000 AD DJ C AJUST SCREW 調整ネジ
24 0CW4144P251// BC GJ N D COVER カバー
25 0CW4A18921000 AH DX C CASTER キャスター
26 0CW4A18926000 AK EB C BRACKET FRONT ブラケット前
27 0CW4A18927000 AK EB C BRACKET REAR ブラケット後
29 0CWFS26593000 AD DJ C GUIDE ROLLER ガイドコロ
30 0CW4A18934000 AR EQ C PLATE RAIL GUIDE レールガイド
31 0CW4A18936000 AX FG C PLATE GUIDE RAIL ガイドレール
32 0CW4A18938000 AH DX C SHAFT ROLLER コロ軸
33 0CW4A18937000 AN EQ C PLATE ROLLER コロ支板
34 0CW4A18910000 AH DX C EARTH SPRING アース板バネ
35 0CW4A18939000 AF DS C ROLLER コロ
36 0CWFC30661000 AC DJ C CLIP クリップ
37 0CW4A18923000 AM EG C BRACKET ブラケット
38 0CW4144P005// AU FG N C BRACKET ブラケット
39 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
41 0CWFC30779000 AC DJ C SCREW(M3×6) ビス
43 0CW4A18935000 AF DS C SHAFT ROLLER コロ軸
44 0CW4A12609000 AC DJ C SCREW(M4×18) ビス
46 0CW4144P250// BD GN N D FRONT LOWER COVER 前下カバー
47 0CW4144P254// BF GN N D REAR LOWER COVER 後下カバー
51 0CW4134P042// AN EQ D EARTH PLATE SPRING アース板スプリング
52 0CW4144P002// AP EQ N C FRAME COVER フレームカバー
53 0CW4144P003// AL EB N C COVER BRACKET 中央カバーブラケット
54 0CWHW080FWS// AC DJ N C WASHER(HW-80) ワッシャー
55 0CWCLP00010// AD DJ N C E-RING E リング
56 0CW4144P252// AM EG N C LOWER COVER 下カバー
57 0CW040120FNBB AB DJ C TAPPING SCREW タッピングビス
58 0CW040100FNBI AA DD C SCREW ビス
601 0CW040080FZWS AA DD C SCREW(M3×8) ビス

–1–
1 取り付けキット (Mounting Hardware)

39
39 27

B 26
39
39
A 47

58
B
1 58 58

39
24 39
58
58 53
39
20
14 39
58 10
39 39

20
39 9 601
52
39
A 4
46
39 6
58
58 601
39 39
20 39 11
55 11
601
53 37 54 25
20 54
58
55 25
601
57
4
6 39
38
39 601
56 11 44
39 39
to copier
55 11
30
54 25 51
41
54 39 31
29
55 25 35
36 43
FCP08971 32
34 33
39

–2–
2 外装カバー (Exteriors Covers,Panels etc.)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A18857000 AG DX C JAM CLEANING KNOB JAM 処理ノブ
2 0CW4144P202// BK HG N D REAR COVER 後カバー
3 0CW4144P726// AY FQ N D FRAME JAM COVER フレーム JAM カバー
4 0CW4144P210// AL EB N D LATCH HANDLE ラッチハンドル
5 0CW4144K502// BA FX N C INTERFACE HARNESS インターフェイスハーネス
6 0CWFC25827000 AE DJ C CLIP クリップ
7 0CW4144P206// BA FX N D DUMMY PUNCHER COVER ダミーパンチャカバー
9 0CW4144P763// AT EZ N C DUMMY PUNCH GUIDE UPPER ダミーパンチガイド上
10 0CW4144P391// BA FX N C DUMMY PUNCH GUIDE ダミーパンチガイド 
11 0CW4144P235// BA FX N D SIDE COVER 横カバー
12 0CW4A17291000 AE DS C TRAY UP/DOWN EMPTY LEVER トレイ昇降エンプティレバー
13 0CW4B10780000 AF DS C PAPER SENSING FLAG REAR 紙検知フラグ後
14 0CW4A17415000 AG DS C TENSION SPRING 引張バネ
15 0CW4A17378000 AD DJ C UPPER COVER LATCH 上カバーラッチ
16 0CW4144P205// AK EB N D UPPER COVER HANDLE 上カバー取手
17 0CW4144P203// BB GD N D UPPER COVER 上カバー
18 0CW4S12048000 AL EB C TENSION SPRING F ネジリバネ F
19 0CW4S12049000 AL EB C TENSION SPRING R ネジリバネ R
20 0CW4A17195000 AF DS C ROLLER HOLDER コロホルダー
21 0CW4A17317000 AC DJ C PAPER FEED ROLLER 搬送コロ
22 0CW4144P200// BF GN N D FRONT COVER 前カバー
23 0CW4144P201// BE GN N D FRONT OPEN COVER 前オープンカバー
24 0CW4A18313000 AE DJ C COVER BAND カバーストラップ
25 0CW4B10585000 AD DJ C SUPPORT PANEL BAND 2 カバーストラップサポート 2
26 0CW4144P727// BE GN N C STACK TRAY 1 スタックトレイ 1
27 0CW4144P728// BA FX N C STACK TRAY 2 スタックトレイ 2
28 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
29 0CW4A17424000 AF DS C EARTH PLATE アース板
30 0CW4144P393// AS EQ N D DOME PLATE 1 ドーム板 1
31 0CW4144P394// AX FG N D DOME PLATE 2 ドーム板 2
32 0CW4A17270000 AG DS C BASE TRAY FLAG ベーストレイフラグ
33 0CW4144P213// BC GJ N C SADDLE TRAY サドルトレイ
34 0CW4144P381// AK EB N C STOPPER ARM ストッパアーム
35 0CW4A17400000 AC DJ C TENSION SPRING 引張バネ
36 0CW4A17408000 AD DJ C TENSION SPRING 引張バネ
39 0CW4A18338010 AH DX C DUMMY PUNCHER PAPER GUIDE ダミーパンチ紙ガイド
40 0CW4144P433// AY FQ N D STAPLE REMOVING LABEL JAM 処理ラベル
41 0CW4A17284000 AD DJ C GEAR(48T/15T) ギア
43 0CW4B10584000 AD DJ C SUPPORT PANEL BAND 1 カバーストラップサポート 1
50 0CW4B10851000 AD DX C TRAY RIB SMALL トレイリブ小
51 0CW4B10845000 AD DJ C SPONGE スポンジ
52 0CW4B10395000 AL EB C TRAY BRACKET F トレイブラケット F
53 0CW4B10394000 AL EB C TRAY BRACKET R トレイブラケット R
56 0CW4144P217// AE DS N C FRONT COVER BAND 前カバーストラップ
57 0CW4144K501// BC GJ N C CONNECTION HARNESS 中継ユニット接続ハーネス
58 0CW4A17380000 AD DJ C TENSION SPRING 引張バネ
61 0CW4144P204// BC GD N D UPPER COVER GUIDE 上カバーガイド
62 0CW4144P207// AR EQ N C DUCT PUNCH パンチダクト
63 0CW4144P208// AN EQ N D FRONT UPPER COVER 前上カバー
64 0CW4144P211// AH DX N C LATCH HOLDER ラッチホルダー
65 0CW4144P209// AP EQ N D REAR UPPER COVER 後上カバー
66 0CWER060SKN// AA DJ N C E-RING(ER-060) E リング
67 0CW4144P216// AF DS N C FUNCTIONAL LEVER 機能部レバー
68 0CW4144P401// AH DX N C FUNCTIONAL SPRING 機能部スプリング
69 0CW4144P100// AZ FQ N C FUNCTIONAL SHAFT 機能部シャフト
70 0CW4144P007// AG DX N C FUNCTIONAL BRACKET 機能部ブラケット
71 0CW4099Q031// AD DJ N C WASHER シャフト固定ワッシャー
72 0CW040100FWWS AC DJ N C SCREW シャフト固定ビス
73 0CW4144P214// AP EQ N D MAINTENANCE COVER メンテナンスカバー
74 0CW0412FNBIT2 AC DJ N C SCREW ビス
75 0CW3090P360// AD DJ C WASHER ワッシャー
76 0CW4144P220// AH DX N D FRONT JAM SUB COVER 前 JAM サブカバー
77 0CW4144P222// AH DX N D REAR JAM SUB COVER 後 JAM サブカバー
78 0CW4113P027A/ AK DX C ROLLER PLATE SPRING コロ板バネ
79 0CW040120FNBB AB DJ C TAPPING SCREW タッピングビス
80 0CW040060FNBI AA DD C SCREW ビス
81 0CWXB47401006 AB DJ C SCREW TAPPING タッピングビス
82 0CW4048P076// AD DJ N C SCREW ビス
83 0CW4144P950// AC DJ N C SPEED NUT スピードナット
84 0CW4144P469// BC GJ N B DISCHARGE BRUSH 除電ブラシ
85 0CW4144P402// AE DS N C LATCH HANDLE SPRING ラッチハンドルスプリング
86 0CW4110P026// AM EG N C TRAY STAY トレイステイ
502 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス
503 0CWXB47300607 AB DJ C SCREW TAPPING(M3×6) タッピングビス
504 0CW4B10848000 AB DJ C SCREW(M4×6) ビス

–3–
2 外装カバー (Exteriors Covers,Panels etc.)
5
43 (CN1) (JS1)

24 TO Puncher Unit (CN20) 57


FIGURE 5
17 62
T a 28
80 TO FIGURE 4
16 (CN2)
80 (CN21)
7 U
TO FIGURE 3 28
79 61 79
80
W 58
TO FIGURE 3 9
19 15 39
80
79 71 72
84 78 20 10 79
20 70
79
15 18 21 X 65 79
27 79 21 502 2
502 TO FIGURE 4 69
79
68
502 21 67
82 66 74
29 80 73
504 79 75
80
80
41
26
50
83
53 13 80
502 11
12
52 SEE FIGURE 9
502 Z 80
28 TO FIGURE 3 14
86 34 30 43 24
28 Y 85 63 79 25
28 TO FIGURE 3
4 51
40 31
28 502 36 77

6 56 25 503
81
33 76 81
79 3
64 V 81
TO FIGURE 3 32 35
22

80

23 80
1

FCP08972

–4–
3 本体機械内部 1 (Internal Components 1)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4109P247// AY FQ N C GEAR(24T) ギア
2 0CW4A17577000 AE DS C STACK LEVER スタックレバー
3 0CW4A17259000 AD DJ C GEAR(16T/18T) ギア
4 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
5 0CWFS19009000 AC DJ C SCREW STEPPED(M3) ダンビス
6 0CW4A17353010 AE DJ C BELT HOLDER REAR ベルトホルダー後
7 0CW4A17354000 AE DJ C BELT HOLDER FRONT ベルトホルダー前
8 0CW4A17371000 AC DJ C TENSIONER ROLLER テンショナコロ
9 0CW4144P400// AD DJ N C LATCH SPRING ラッチバネ
10 0CW4A17414000 AD DJ C TENSION SPRING 引張バネ
11 0CW4A17417000 AD DJ C TENSION SPRING 引張バネ
12 0CW4A17419000 AD DJ C TENSION SPRING 引張バネ
13 0CW4109P248// AV FG N C GEAR(18T/24T) ギア
14 0CW4A17517000 AE DS C LATCH ラッチ
15 0CW4144P212// AG DX N C LATCH ARM ラッチアーム
16 0CW4H16512000 AF DS C CABLE STACK SENSOR スタックセンサー束線
17 0CW4A17523000 AC DJ C BUSHING ブッシング
18 0CW4A17524000 AD DJ C PULLEY(18T) プーリー
19 0CW4A17528000 AC DJ C BUSHING ブッシング
20 0CW4A17542000 AC DJ C FLANGE フランジ
21 0CW4A17567000 AD DJ C CLIP SHAFT 軸クリップ
22 0CW4A17572000 AE DJ C BUSHING ブッシング
23 0CW4A17691000 AC DJ C LEAF SPRING 板バネ
24 0CW4A17288000 AD DJ C PULLEY(40T) プーリー
25 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
26 0CW4S19077000 AC DJ C SCREW(M4×8) ビス
27 0CW4F11556000 AG DX C PLATE PAPER FEED TENSIONER 搬送テンショナ板
28 0CWFC25827000 AE DJ C CLIP クリップ
29 0CW4A17265000 AC DJ C RAIL ROLLER レールコロ
31 0CW4A17318000 AK DX C STOPPER GUIDE 処理ストッパガイド
32 0CW4A17539000 AK DX C LINK 1 リンク 1
33 0CW4A17540000 AC DJ C LINK 2 リンク 2
34 0CW4A17549000 AC DJ C TENSION SPRING 引張バネ
35 0CW4K11080000 BF GN B STEPPING MOTOR ステッピングモーター
36 0CWFC25034000 AB DJ C SCREW W/WASHER(M3×6) バネ付ナベビス
37 0CW4A17355000 AD DJ C PULLEY(18T) プーリー
38 0CWXF21817960 AS EZ B BELT TIMING タイミングベルト
39 0CWXF21619860 AQ EQ B BELT TIMING タイミングベルト
40 0CWXF21618840 AP EQ B BELT TIMING タイミングベルト
41 0CW4H16460000 AP EQ C CABLE SENSOR センサー束線
42 0CW4H16602000 AU EZ C BUNDLE WIRE FOR THE PADDLE MOTOR バンドルワイヤー
43 0CW4H16467000 AP EQ C CABLE DC MOTOR DC モーター束線
44 0CW4A17321000 AR EQ C STOPPER ARM ストッパアーム
45 0CW4A17400000 AC DJ C TENSION SPRING 引張バネ
46 0CWXF21605040 AL EB B BELT TIMING タイミングベルト
47 0CW4F11882000 AT EZ C TRAY STAY F トレイステイ F
48 0CW4144P016// AG DX N C LATCH GUIDE PIN ラッチピンガイド
49 0CW4A17578000 AD DJ C PAD パッド
50 0CW4B10785000 AC DJ C PAD パッド
51 0CW4B10390000 AN EQ C MOTOR PLATE モータープレート
52 0CW4F11883000 AN EQ C TRAY STAY R トレイステイ R
53 0CW4A17576000 AH DX C STACK LEVER BRACKET スタックレバーブラケット
54 0CW4A17482000 AP EQ C FR-ST STAY FR-ST ステイ
55 0CW4A17491000 AW FG C STAY FRAME ステイフレーム
56 0CW4A17511000 AR EQ C FR DUCT RU FR ダクト RU
57 0CW4A17217000 AV FG C STACK SHAFT スタック軸
58 0CW4A17510000 AK DX C CABLE GUIDE(MIDDLE REAR) 束線ガイド ( 中後 )
59 0CW4A17253000 AS EZ C FRAME LATCH SHAFT フレームラッチ軸
60 0CW4F11560000 AH DX C PULLEY SUPPORT PLATE(FRONT LOWER) プーリー支板 ( 前下 )
61 0CW4A17512000 AE DJ C CABLE GUIDE(REAR LOWER) 束線ガイド ( 後下 )
62 0CW4A17543000 AE DS C CABLE GUIDE 束線ガイド
63 0CW4A17489000 AG DS C STACK MOTOR REINFORCEMENT PLATE スタックモーター補強板
64 0CW4A17474000 AG DS C RISE AND FALL SUPPORT PLATE(FRONT) 昇降押え板 ( 前 )
65 0CW4F11558000 AH DX C PULLEY SUPPORT PLATE(REAR LOWER) プーリー支板 ( 後下 )
66 0CW4A17475000 AH DX C TS SUPPORT PLATE(REAR) TS 押え板 ( 後 )
67 0CW4109P427// AC DJ N C SCREW(M4×7) ビス
68 0CW4109P207// AD DJ N C SPACER COLLAR スペーサーカラー
501 0CWXD32200142 AC DJ C PIN DOWEL 平行ピン
502 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス
503 0CWXD12300142 AC DJ C PIN DOWEL 平行ピン

–5–
3 本体機械内部 1 (Internal Components 1)

5 10 4
4
53 37
45 38
20
2 66

65
25 26
(PI24) 4
(CN73) TO FIGURE 6 67
2
16 29 28
(CN19) Z
8
27
29 12
49
28
31 47 23 8
34
TO FIGURE
2 29 46
33 1
Y 29
32
39
7 33 4 68
34 44 11 13 28
4
32 17
28 A
23 52
11 48 36
20 58
38 28 35
37 50 14 (M2)
51 (CN57)
60
TO FIGURE 2
59
64
4 W 4
54 62
4
10 26
4 501 4
4 40
24 61
22 21 57
21 TO FIGURE 2
20
U
28 56
15 55 4 4
18 9
503 TO FIGURE 2 63
3
(CN56) (CN57) V 20
4
(CN50) (CN71)
41 19
(CN10)
(CN49) A 503
(CN48) (CN6)
42 502 21
(CN15)
22 (CN70)
(CN47) 43
SEE FIGURE 7

FCP08973

–6–
4 本体機械内部 2 (Internal Components 2)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4144P705// AL EB N D INTERFACE HOLDER インターフェイスホルダー
2 0CW4S19077000 AC DJ C SCREW(M4×8) ビス
3 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
4 0CW4B10586010 AC DJ C PLATE STAPLER FRAME STOPPER ステイプラフレーム ストッパ
5 0CWFC25827000 AE DJ C CLIP クリップ
6 0CWFS21672000 AD DJ C BUSHING ブッシング
7 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
8 0CW4A18316000 AD DJ D BLANKING COVER 目隠しカバー
9 0CW4A17515000 AC DJ C FRAME TRAY ROLLER 処理トレイコロ
10 0CW4A17172010 AN EQ C PAPER GUIDE LOWER 通紙ガイド下
11 0CW4A17349000 AF DS C SENSOR FLAG センサーフラグ
12 0CW4A17418000 AD DJ C TENSION SPRING 引張バネ
13 0CW4H16454000 AE DS C CABLE SENSOR センサー束線
14 0CW4A17371000 AC DJ C TENSIONER ROLLER テンショナコロ
15 0CW4F11557000 AH DX C PLATE PAPER FEED TENSIONER 2 搬送テンショナ板 2
16 0CW4060P027// AB DJ N C SCREW ビス
17 0CW4H16449010 AM EG B MICROSWITCH マイクロスイッチ
18 0CWXF21607440 AK DX B BELT TIMING タイミングベルト
19 0CW4A17505000 AD DJ C TOP SENSOR FLAG トップセンサーフラグ
20 0CW4A17506000 AE DS C SWITCH LEVER スイッチレバー
21 0CW4A17507000 AD DJ C LEVER SUPPORT HOLDER レバー押えホルダー
22 0CW4A17508000 AG DX C SENSOR/MICROSWITCH HOLDER センサー / マイクロスイッチホルダー
23 0CW4144P314// AD DJ N C ROLLER GEAR(24T) ローラーギア
24 0CW4144P215// AL EB N C PAPER WEIGHT GUIDE 1 重りガイド 1
25 0CW4A17495000 AD DJ C WEIGHT PLATE 1 重り板 1
26 0CW4A17496000 AD DJ C WEIGHT PLATE 2 重り板 2
27 0CW4144P751// AG DX N C PAPER WEIGHT GUIDE 2 重りガイド 2
28 0CW4A17488000 AV FG D FRAME COVER フレームカバー
29 0CW4A18314000 AC DJ C LEAF EARTH COVER アース板バネ
30 0CW4H16452000 AQ EQ C FRONT DOOR SENSOR CABLE 前ドアセンサー束線
31 0CW4H16453000 AU EZ C LEVER TRAY SENSOR CABLE レバートレイセンサー束線
32 0CW4H16461000 AN EQ C SENSOR CABLE 2 センサー束線 2
33 0CW4H16462000 AL EB C SENSOR CABLE 3 センサー束線 3
34 0CW4A17409000 AD DJ C TENSION SPRING 引張バネ
35 0CW4H16465000 AQ EQ C JOG MOTOR CABLE ジョグモーター束線
36 0CW4H16553000 AS EQ C SWITCH CABLE スイッチ束線
37 0CW4134K328// AF DS C BIND CLUTCH CABLE バインドクラッチ束線
38 0CW4116P405B/ BA FX C PAPER FEED ROLLER 搬送ローラー
39 0CW4048P300// AC DJ C SCREW ビス
40 0CW4A17467000 AF DS C SENSOR BRACKET センサーブラケット
41 0CW4A18951000 AG DX C JOINT-SWITCH HOLDER ジョイントスイッチホルダー
42 0CW4A18948000 AN EG C GROUNDING PLATE グラウンディングプレート
43 0CW4A18869000 AE DS C SWITCH LEVER スイッチレバー
44 0CW4A18863000 AE DJ C SPRING スプリング
46 0CW4144K302// CE UF N E DC CONTROLLER PWB ASSEMBLY DC コントローラー回路基板
47 0CW4A17426000 AH DX C PROCESSING TRAY FRAME LOCK PLATE 2 処理トレイフレームロック板 2
48 0CW4A17425000 AE DS C PROCESSING TRAY FRAME LOCK PLATE 1 処理トレイフレームロック板 1
49 0CWVT25019030 AE DS C SLIP GUIDE スリップガイド
50 0CWVT20002018 AE DJ C PWB SPACER 基板スペーサー
51 0CWVT25171030 AE DS C PWB SPACER 基板スペーサー
501 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス
502 0CWXD32200122 AC DJ C PIN DOWEL 平行ピン

–7–
4 本体機械内部 2 (Internal Components 2)

3
41 42
44
B 17 43
(MS2)
(CN64) (CN69)
SEE FIGURE 8 SEE FIGURE 2
35 a
(CN53) (CN62) 3
13 1
(CN50) (CN3) (CN43)
(CN36)
7
39
(PI1) (CN44) 23
(CN44) 502 5
39 18
6 14
33 15
12 (CN72)
(CN9) 37
40 16
(CN18)
11
SEE FIGURE 19
3
10 34 B 2

3 47
48
3 49
38
46
9
48 9
7 50
TO FIGURE 2 47
(PI4) 4
(CN23) X
8
39 51
A (PI13)
(CN47) 36
3 6 25
5 24 7
(CN66) (CN69)

26 27
3 3 B
7 (CN68) (CN8)
7 (PI22)
(CN25) (PI23)
28
C
(CN24)

19
22

3 (CN42)
17 A 29
C 3
(MS1) (CN23)
3 (CN68)
(CN36)
(CN24) 31 (CN37)
21 32
(CN25) (CN33)
(CN28)
20 501 (CN16)
(CN4)
(CN5)
FCP08974
30
–8–
5 パンチャ部 (Puncher Assembly)[AR-PN1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4G11297020 CA TR E PUNCHER CONTROLLER PWB ASSEMBLY パンチャコントローラー回路基板
2 0CW4A18685000 AF DS C PUNCHER SHUTTER パンチャシャッター
3 0CW4H16514000 AP EQ C CABLE POWER CONNECTING 電源中継束線
4 0CW4H16515000 AH DX C CABLE INTERFACE インターフェイス束線
5 0CW4A18683000 AE DJ C TENSION SPRING 引張バネ
6 0CW4H16524000 AV FG C CABLE SENSOR センサー束線
7 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
8 0CW4B10489000 AF DS D LABEL パンチクズステラベル
9 0CW4A18672000 AY FQ C PUNCHER MOUNT パンチャ台
10 0CW4A18673000 AF DS D HARNESS COVER ハーネスカバー
11 0CW1020K367// AP EQ N E DUST LED PWB UNIT ダスト LED 回路基板
12 0CW1020K369// AP EQ N E DUST PTR PWB UNIT ダスト PTR 回路基板
13 0CW4A18679000 AF DS C GEAR(16T/33T) ギア
14 0CW4A18680000 AF DS C GEAR(19T/32T) ギア
15 0CW4A18681000 AM EG C PUNCHER DUCT パンチャダクト
16 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
17 0CW4A18686000 AT EZ D DUST BOX PANEL ダストボックス
18 0CW4B10495000 AQ EQ D DUST BOX COVER ダストボックスカバー
19 0CW4K11078000 BB FX B STEPPING MOTOR ステッピングモーター
20 0CW4H16530000 AG DX C CABLE DUST SENSOR クズ検知束線
21 0CW4A18704000 AN EQ D PUNCHER BASE COVER パンチャベースカバー
22 0CW4A18708000 AY FQ C DUST BOX MYLAR ダストボックスマイラー
23 0CW4B10847000 AF DS D DUST-BOX RUBBER ダストボックスラバー
25 0CW4B10493000 AE DS C DUST BOX SPONGE ダクトボックススポンジ
26 0CW4144K146// AW FG N E PUNCHER GUIDE UNIT パンチ入口ガイドユニット
27 0CW4144P245// AS EZ N C PUNCHER GUIDE パンチ入口ガイド
28 0CW4144P445// AH DX N C PUNCHER GUIDE SHEET パンチ入口ガイドマイラー
29 0CW030080FDBB AB DJ N C SCREW(3×8) ビス
50 0CW1020P537A/ BS MJ B IC M38039FFSP CPU CPU
51 0CWWA70484000 AN EG B IC S-93C46ADP EP-ROM EP-ROM
52 0CW4F11850000 AU EZ C PC-PM-SUB BASE ASSY PC-PM サブベース
53 0CW4B10494000 AS EQ C DUST BOX SHEET ダストボックスシート
54 0CW1020P280A/ AH DX C RIB リブ
55 0CW4A18684000 AF DS C PC SENSOR PLATE PC センサープレート
56 0CW4A18689000 AF DS C PC-PWB FILM PC 基板フィルム
501 0CWXB12400605 AB DJ C SCREW(M4×6) ビス
502 0CWXB47300805 AB DJ C SCREW TAPPING(M3×8) タッピングビス
503 0CWXD11104629 AC DJ C WASHER ワッシャー
504 0CWXB24300605 AB DJ C SCREW W/WASHER(M3×6) バネ付ナベビス

–9–
5 パンチャ部 (Puncher Assembly)[AR-PN1]

501

SEE FIGURE 6 15

5
(J1005)
20
502

503 13 51 (J2006)
50
14
(J2005) 3 (J2004)
7
1 (J1004)
(J2003)
55
(J1003) 4
(PI2P) 7
16 (J2007) TO Saddle Finisher
FIGURE 2
(J2007) 52
(M2P) T
6
(J2008)
(J2009) (J1001)
(J1006) 8
19
54 504 29

502 27
502
56
10 (J2006)

12 28

501 26
2
9 28

18
(J2005) 21 53

11
502 502
53

25
`
```

See figure12 17
22 FCP08975
23 25

– 10 –
6 パンチャトータル部 (Puncher Total Assembly)[AR-PN1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A18688000 AD DJ C PUNCHER ROLLER パンチャコロ
2 0CW4H16523000 BA FX C CABLE REGISTRETION SENSOR レジストセンサー束線
3 0CWFS19102000 AC DJ C SCREW STEPPED(M3) ダンビス
4 0CWFS56528000 AE DJ C EARTH ROLLER アースコロ
5 0CW4A18682000 AG DX D REGSTRETION COVER レジストカバー
6 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
7 0CWFF60507000 AV FG C SENSOR HOLDER UPPER トウカセンサーホルダー上
8 0CWFF60508000 AV FG C SENSOR HOLDER LOWER トウカセンサーホルダー下
9 0CWFB56775000 AH DX C ENSOR FLAG PLATE センサーフラグ板
10 0CW4B10476000 AG DS D JAM CLEARING COVER JAM 処理カバー
11 0CWFB55968000 AH DX C SLIDE RACK スライドラック
12 0CW4B10477000 AG DS C JAM CLEANING KNOB JAM 処理ノブ
14 0CW1033K300// BD GN N B MOTOR DC DC モーター
15 0CW4H16531000 AP EQ C CABLE MOTOR モーター束線
16 0CW1020K363B/ AX FG E PWB UNIT 回路基板
17 0CW1020K365B/ AX FG E PWB UNIT 回路基板
20 0CW4B10490000 AG DX C SPRING スプリング
21 0CW4A18690000 AH DX C PC SENSOR BRACKET PC センサーブラケット
22 0CWFB55969000 AE DJ C BEARING SLIDE ベアリングスライド
501 0CWXB12300605 AB DJ C SCREW(M3×6) ビス
502 0CWXB47300805 AB DJ C SCREW TAPPING(M3×8) タッピングビス
503 0CWXD21100502 AC DJ C E-RING E リング
504 0CWXB47301209 AB DJ C SCREW TAPPING(M3×12) タッピングビス
505 0CWXB24300805 AB DJ C SCREW W/WASHER(M3×8) バネ付ナベビス
506 0CWXD21100642 AC DJ C E-RING E リング
507 0CWXB12300805 AB DJ C SCREW(M3×5) ビス
508 0CWXB12400805 AB DJ C SCREW(M4×6) ビス

6 パンチャトータル部 (Puncher Total Assembly)[AR-PN1]

(PI3P)
6 15
(J2009)
6 (J1002)

(PI1P) (J2002)
(J2008)
508

21
506 (M1P)
505 (J2002)
9
3 11
4
503
12
14
20
2
1
501
3 (J1007)
22
507 504
(J2011)
5
8
10
3
(J2011) (J2010)
1
501 (J2010)
1
3 17

16
502

7
501
502 FCP08976

– 11 –
7 スタックモーター駆動部 (Stack Motor Driver Assembly)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A17260000 AF DS C GEAR(16T/40T) ギア
2 0CW4A17261000 AG DS C GEAR(16T/45T) ギア
3 0CW4A17262000 AE DS C GEAR(16T/45T) ギア
4 0CW4A17263000 AE DS C PULLEY(56T) プーリー
5 0CW4H16458000 AK DX C CABLE SHIFT MOTOR シフトモーター束線
6 0CW4135K550// BD GN B MOTOR(NA3550D01C) DC モーター
7 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
8 0CWFC25034000 AB DJ C SCREW W/WASHER(M3×6) バネ付ナベビス
9 0CWFC25827000 AE DJ C CLIP クリップ
10 0CWFS21672000 AD DJ C BUSHING ブッシング
11 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
12 0CWXF21608040 AN EG B BELT TIMING タイミングベルト
13 0CW4A17264000 AE DJ C CLOCK SENSOR PLATE クロックセンサー板
14 0CW4A17469000 AD DJ C STACK MOTOR SUB PLATE スタックモーターサブプレート
15 0CW4F11562000 AT EZ C STACK MOTOR PLATE ASSY スタックモータープレート
16 0CW4A17173000 AD DJ C CLOCK SENSOR BRACKET クロックセンサーブラケット
501 0CWXD32200122 AC DJ C PIN DOWEL 平行ピン
502 0CWXD32200142 AC DJ C PIN DOWEL 平行ピン

7 スタックモーター駆動部 (Stack Motor Driver Assembly)


9
4
502
12
9
10
11
1
(PI16)
(CN49)
15
11 (PI17)
(CN48)
2

9 7
3
16

501 8
13 5
(CN70)
9
(CN70)
7

(M6)
(CN70)

14
6

10 FCP08977
9

– 12 –
8 駆動部 (Drive Assembly)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A17301000 AE DS C GEAR(58T) ギア
2 0CW4A17302000 AQ EQ C GEAR(23T) ギア
3 0CW4A17303000 AK DX C GEAR(17T/65T) ギア
4 0CW4A17304000 AL EB C GEAR(15T/54T) ギア
5 0CW4A17305000 AL EB C GEAR(17T/29T) ギア
6 0CW4A17306000 AH DX C GEAR(20T) ギア
7 0CW4A17307000 AF DS C PULLEY(45T) プーリー
8 0CW4A17338000 AH DX C GEAR(82T) ギア
9 0CW4A17566000 AD DJ C CLIP SHAFT 軸クリップ
10 0CW4A17567000 AD DJ C CLIP SHAFT 軸クリップ
11 0CW4A17572000 AE DJ C BUSHING ブッシング
12 0CW4A17573000 AE DS C BUSHING ブッシング
13 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
14 0CWFS21615000 AS EZ C BALL BEARING ボールベアリング
15 0CWXF21807000 AP EQ B BELT TIMING タイミングベルト
16 0CW4A17300000 AD DJ C GEAR(29T) ギア
17 0CWFC25031000 AC DJ C SCREW(M4×6) ビス
18 0CW4A17308000 AS EZ C CLOCK SENSOR FLAG クロックセンサーフラグ
19 0CW4K11069000 BR LX B DC MOTOR(DC24V) DC モーター
20 0CWWG85421000 AR EQ B PHOTO INTERRUPTER フォトインタラプタ
21 0CW4A17407000 AD DJ C COMPRESSION SPRING 圧縮バネ
22 0CW4H16468000 AY FQ C CABLE STAPLER ステイプラ束線
23 0CW4S19049000 AD DJ C SCREW STEPPED 段ビス
24 0CW4A17479000 AD DJ C DRAWER D PLATE ドロワ D プレート
25 0CW4A17516000 AK DX C DRAWER D BRACKET ドロワ D ブラケット
26 0CW4A17199000 AE DJ C MOTOR SENSOR PLATE モーターセンサープレート
27 0CW4F11563010 BA FX C DRIVE GEAR BRACKET ASSY 駆動ギアブラケット
28 0CW4A17229000 AL EB C GEAR SHAFT 1 ギアシャフト
29 0CW4A17231000 AL EB C GEAR SHAFT 2 ギアシャフト
30 0CW4A17198000 AQ EQ C DRIVE GEAR BRACKET ASSY 駆動ギアブラケット
501 0CWXD32200142 AC DJ C PIN DOWEL 平行ピン
502 0CWXD32300182 AC DJ C PIN DOWEL 平行ピン
503 0CWXD32200122 AC DJ C PIN DOWEL 平行ピン

8 駆動部 (Drive Assembly)


(CN71) 20 18
26
19 (PI14)
(CN52)

13
13
21 (M7)
17 15
24 10
A 27
23 7
25 501
14
13 21 28
(CN72) 503
A 16
10
(CN7)
9
23 12
22
(CN11) 8
29
502
13
1
2
13 2

11
10

30 4 3 5
10
12
9

6 FCP08978

– 13 –
9 束線押えカバー部 (Bundle Support Cover Assembly)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4H16454000 AE DS C CABLE SENSOR センサー束線
2 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
3 0CW4A17416000 AD DJ C TENSION SPRING 引張バネ
5 0CW4A17371000 AC DJ C TENSIONER ROLLER テンショナコロ
6 0CWFC25827000 AE DJ C CLIP クリップ
7 0CW4A17240000 AM EG C SUPPORT SHAFT 押え軸
8 0CW4A17289000 AF DS C GEAR(20T/28T) ギア
9 0CW4113P243// AE DS C PAPER SENSOR LEVER 紙面検知レバー
10 0CW4A17325000 AE DS C GEAR(5T) ギア
11 0CW4A17367000 AD DJ C BUSHING ブッシング
12 0CW4A17421000 AE DJ C TENSION SPRING ネジリバネ
13 0CW4A17422000 AE DS C TENSION SPRING ネジリバネ
14 0CW4A17423000 AE DS C TENSION SPRING ネジリバネ
15 0CW4A17526000 AF DS C SENSOR HOLDER センサーホルダー
16 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
17 0CW4116P492// AL EB C PAPER SUPPORT GUIDE ツウシガイド
18 0CW4A17327000 AD DJ C PAPER SUPPORT HOLDER ツウシガイドホルダー
19 0CW4B10783000 AG DX C GEAR HOLDING SPRING ギア固定スプリング
20 0CW4A17184000 AN EG C BUNDLE-SUPPORTING BRACKET 束線押えブラケット
21 0CW4060P027// AB DJ N C SCREW ビス
22 0CW4F11566000 AG DX C SUPPORT PLATE ツウシプレート

9 束線押えカバー部 (Bundle Support Cover Assembly)


7
11
12
14
9
10

19

8 16
(PI9)
13 (CN35)

18
1
(CN34)
2

6 15
17 5

21

22 20

FCP08979

– 14 –
F 処理部 (Dispose Assembly)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A17390000 AD DJ C TENSION SPRING 引張バネ
2 0CW4H16454000 AE DS C CABLE SENSOR センサー束線
3 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
4 0CWXF21606140 AL EB B BELT TIMING タイミングベルト
5 0CW4A17328000 AD DJ C BELT SENSOR LEVER ベルトセンサーレバー
6 0CW4A17383000 AY FQ B TIMING BELT タイミングベルト
7 0CW4A17392000 AE DS C TENSION SPRING ネジリバネ
8 0CW4144P303// AL EB N D DISPOSE COVER 処理カバー
9 0CW4060P027// AB DJ N C SCREW ビス
10 0CW4H16455000 AK EB C CABLE TRAY トレイ束線
11 0CW4K11067000 BA FX B STEPPING MOTOR ステッピングモーター
12 0CWFC25034000 AB DJ C SCREW W/WASHER(M3×6) バネ付ナベビス
13 0CW4A18889010 AD DJ C TRAY GUIDE FRONT トレイガイド前
14 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
15 0CW4A17273000 AD DJ C GEAR(30T) ギア
16 0CW4A17519000 AR EQ D DISPOSE SUB COVER 処理サブカバー
17 0CW4A17368000 AP EQ C PULLEY(22T) プーリー
18 0CW4A17381000 AS EQ C BUNDLE ROLLER LOWER タバダシローラー下
19 0CW4A17567000 AD DJ C CLIP SHAFT 軸クリップ
20 0CW4A17572000 AE DJ C BUSHING ブッシング
21 0CW4A18319000 AD DJ C PULLEY(22T) プーリー
22 0CW4A18334000 AC DJ C FLANGE フランジ
0CW4114P048B/ AU EZ C SENSOR FLAG SUPPORT PLATE (INCH SERIES) センサーフラグ支板
23
0CW4B10138010 AU EZ C SENSOR FLAG SUPPORT PLATE (AB SERIES) センサーフラグ支板
24 0CW4A17329000 AE DS C SENSOR FLAG センサーフラグ
25 0CW4A17402000 AC DJ C TENSION SPRING 引張バネ
26 0CW4H16464000 AN EQ C CABLE EJECT MOTOR イジェクトモーター束線
27 0CW4A17275000 AD DJ C PULLEY(22T) プーリー
28 0CW4A18924010 AD DJ C GUIDE TRAY REAR トレイガイド後
29 0CWFC25827000 AE DJ C CLIP クリップ
30 0CWFS21672000 AD DJ C BUSHING ブッシング
31 0CW4A17209000 AC DJ C LEAF SPRING 板バネ
32 0CW4144P290// AR EQ N C PAPER FEED GUIDE FRONT 処理ガイド前
33 0CW4A17514000 AE DS C BUNDLE ROLLER FLAG タバローラーフラグ
34 0CW4K11066000 BE GN B STEPPING MOTOR ステッピングモーター
35 0CW4144P289// AR EQ N C PAPER FEED GUIDE REAR 処理ガイド後
36 0CW4A17314000 AH DX D ADJUSTMENT RACK FRONT 整合ラック前
37 0CW4A18877000 AF DS D ADJUSTMENT RACK COVER FRONT 1 整合ラックカバー前 1
38 0CW4144P277// AG DX N D ADJUSTMENT RACK COVER FRONT 2 整合ラックカバー前 2
39 0CW4A17391000 AC DJ C COMPRESSION SPRING 圧縮バネ
40 0CW4A17319000 AL EB C ADJUSTMENT RACK REAR 整合ラック後
41 0CW4144P284// AG DX N D ADJUSTMENT RACK COVER REAR 整合ラックカバー後
42 0CW4A17212000 AE DS C MICROSWITCH HOLDER マイクロスイッチホルダー
43 0CW4A17575010 AE DS D MICROSWITCH COVER マイクロスイッチカバー
44 0CW4H16449010 AM EG B MICROSWITCH マイクロスイッチ
45 0CW4B10779000 AF DS C ADJUSTMENT-PLATE MYLAR REAR 整合プレートマイラー後
46 0CW4B10778000 AF DS C ADJUSTMENT-PLATE MYLAR FRONT 整合プレートマイラー前
49 0CW4B10776000 AF DS C ADJUSTMENT-RACK MYLAR 整合ラックマイラー
50 0CW4A17239000 AK DX C PAWL BRACKET SHAFT ポールブラケット軸
51 0CW4A17486000 AM EG C MOTOR BRACKET モーターブラケット
52 0CW4A17191000 AF DS C SENSOR BRACKET センサーブラケット
53 0CW4F11564000 AW FG C ADJUSTMENT BASE ASSY 整合ベース
54 0CW4A17236000 AS EQ C LOWER TB ROLLER SHAFT 下 TB ローラーシャフト
55 0CW4A17487000 AF DS C P-LOCK BRACKET P- ロックブラケット
56 0CW4A17193000 AG DS C SIG SENSOR BRACKET SIG センサーブラケット
57 0CW4B10852000 AE DS C SUPPORT SHEET 補助シート
60 0CW4A17196000 AH DX C PULLEY SHAFT SUPPORT PLATE プーリー軸支板
61 0CW4A17483000 AL EB C STAY 整合ステー
62 0CW4A17266000 AE DS C SENSOR SUPPORT PLATE センサー支板
63 0CW4B10086000 AL EB C WEIGHT FLAPPER INSIDE 排紙ウェイト中
64 0CW4B10144000 AE DJ C WEIGHT FLAPPER SHEET INSIDE 排紙ウェイトマイラー中
65 0CW4B10085000 AK EB C WEIGHT FLAPPER FRONT 排紙ウェイト前
66 0CW4B10156000 AE DJ C WEIGHT FLAPPER SHEET FRONT 排紙ウェイトマイラー前
67 0CW4B10087000 AK EB C WEIGHT FLAPPER REAR 排紙ウェイト後
68 0CW4B10082000 AF DS C WEIGHT FLAPPER SHEET REAR 排紙ウェイトマイラー後
69 0CW4144P053// AP EQ N C PAWL SHEET HOLDER 爪シートホルダー
70 0CW4144P408// AF DS N C PAWL SHEET 爪シート
501 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス
502 0CWXD32200122 AC DJ C PIN DOWEL 平行ピン
503 0CWXD32200102 AC DJ C PIN DOWEL 平行ピン
504 0CWXB12400606 AB DJ C SCREW(M4×12) ビス

– 15 –
F 処理部 (Dispose Assembly)

504
67 14
504 8
(CN50)
3
65 63 (PI15) 62
44 3
68 43 12
66 64 3 (M1)
42 (MS3)
(CN66) (CN56)
(PI2)
16 29 (CN51) 34
28
SEE FIGURE 11 51 14
27
503 4 52
(CN54)
9 30
3
25 50
60
40 2
30 41 (CN55)
503 3 45
27
B 13
29 23
3

38 46 31
32 24
37 5 69
61 35 70
39
49
7 A
57 B 20
6
36 19
39 54
22
33 15 19 21
502 18
31 70 69 502
(CN31)

6 19 (CN30)
53 A 22 (CN32)
17
3
501 18 10
502 (CN29)
29
11 (M5) 501 20
(CN65)
1
12
(PI7) 11
(CN31) 12 55 4
(M4)
(CN63)
14 3 (M3)
56 (CN59) 9
14 (PI6) 26
14
(CN30) 34 (CN13)
(PI8)
(CN32) (CN59)
3 12

FCP08980

– 16 –
G 搬送部 (Paper Feeder Assembly)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A17278000 AC DJ C FLANGE フランジ
2 0CW4A17281000 AD DJ C PULLEY(20T) プーリー
3 0CW4A17337000 AE DS C PAPER AUXILIARY GUIDE 紙補助ガイド
5 0CW4A17401000 AD DJ C TENSION SPRING 引張バネ
6 0CW4109P231// AD DJ C PAWL FRONT 爪前
7 0CW4109P232// AD DJ C PAWL REAR 爪後
8 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
9 0CWFC25827000 AE DJ C CLIP クリップ
10 0CW4A17271000 AP EQ C PULLEY(40T) プーリー
11 0CW4A17272000 AN EQ C PULLEY(18T/29T) プーリー
12 0CW4A17274000 AD DJ C GEAR(20T/32T) ギア
13 0CW4A17276000 AC DJ C FLANGE フランジ
14 0CW4A17279000 AD DJ C GEAR(20T) ギア
15 0CW4A17280000 AD DJ C GEAR(30T/20T) ギア
16 0CW4A17330000 AD DJ C SENSOR FLAG センサーフラグ
17 0CW4A17331000 AD DJ C CAM カム
18 0CW4A17332000 AC DJ C LINK ARM 1 リンクアーム 1
19 0CW4A17346000 AC DJ C PADDLE SHAFT SUPPORT パドル軸台
20 0CW4A17347000 AD DJ C LINK ARM 2 リンクアーム 2
21 0CW4A17348000 AD DJ C LINK ARM 3 リンクアーム 3
22 0CW4A17351000 AD DJ C PULLEY(24T) プーリー
23 0CW4A17366000 AE DJ C LINK ARM 4 リンクアーム 4
24 0CW4114P813// AF DS C COMPRESSION SPRING 圧縮バネ
25 0CW4A17339000 AC DJ C FLANGE フランジ
26 0CW4A17372000 AH DX C SAFETY GUIDE REAR 1 セーフティガイド後 1
27 0CWFS21672000 AD DJ C BUSHING ブッシング
28 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
29 0CWXF21604940 AL EB B BELT TIMING タイミングベルト
30 0CWXF21607640 AN EG B BELT TIMING タイミングベルト
31 0CW4A17194000 AR EQ C PAPER OUTLET GUIDE UPPER 紙出口ガイド前
32 0CW4A17427000 AT EZ C ELIMINATOR STATIC CHARGE 除電シン
33 0CW4114P352// AH DX N C SAFETY GUIDE REAR 2 セーフティガイド後 2
34 0CW4A17406000 AH DX C PAPER OUTLET ROLLER 紙出口コロ
35 0CW4113P643B/ AR EQ C PAPER OUTLET ROLLER PLATE 紙出口コロ支板
37 0CW4A17531000 AK DX C PAPER OUTLET ROLLER 1 紙出口ローラー 1
38 0CW4116P759// AN EG C WEIGHT FLAPPER ROLLER 排紙ローラー
39 0CW4A17352000 AC DJ C PADDLE ROLLER HOLDER 1 パドルローラーホルダー 1
41 0CW4A17513000 AD DJ C SENSOR FLAG CAM センサーフラグカム
42 0CW4A17585000 AE DJ C FLANGE フランジ
43 0CW4A17333000 AN EG C PAPER GUIDE LOWER 紙ガイド下
44 0CW4A17283000 AC DJ C GEAR(14T) ギア
45 0CW4A17282000 AC DJ C GEAR(14T) ギア
46 0CW4A17286000 AE DS C ROLLER HOLDER FRONT 1 ローラー支持ブロック前 1
47 0CW4A17345000 AE DJ C ROLLER HOLDER FRONT 2 ローラー支持ブロック前 2
48 0CW4A17379000 AS EQ C BUNDLE ROLLER UPPER 束ローラー上
49 0CW4113P352// AG DX C SAFETY GUIDE FRONT セーフティガイド前
50 0CW4A17285000 AE DS C ROLLER HOLDER REAR 1 ローラー支持ブロック後 1
51 0CW4A17344000 AE DJ C ROLLER HOLDER REAR 2 ローラー支持ブロック後 2
52 0CW4A17341000 AH DX C SAFETY GUIDE セーフティガイド
53 0CW4B10846000 AD DJ C JUMP STOCK ジャンプストック
56 0CW4B10591000 AF DS C WASHER ワッシャー
57 0CW4139P139// AR FG C EXIT ROLLER SHAFT 出紙ローラーシャフト
58 0CW4A17192000 AE DS C CAM SENSOR BRACKET カムセンサーブラケット
59 0CW4F11565000 AP EQ C TRANSFER FRAME REAR 搬送フレーム後
60 0CW4A17234000 AR EQ C CAM SHAFT カムシャフト
61 0CW4A18320000 AC DJ C SR-PAD SR パッド
62 0CW4A17202000 AK DX C TRANSFER FRAME FRONT 搬送フレーム前
63 0CW4A17237000 AT EZ C PDL SHAFT PDL シャフト
64 0CW4110P362// AD DJ C DUMMY PADDLE HOLDER ダミーパドルホルダー
65 0CW4B10140000 AN EQ C PADDLE SMALL パドル小
66 0CW4B10149000 AD DJ C PADDLE HOLDER パドルホルダー
67 0CW4A17238000 AR EQ C ROLLER SHAFT UPPER ローラー軸上
68 0CW4B10111000 AE DS C PDL SMALLNESS HOLDER REAR パドル小ホルダー後
69 0CW4A18888000 AN EG C PADDLE RUBBER パドルラバー
70
0CW4114P401// AE DJ C TENSION SPRING (AB SERIES) 引張バネ
0CW4134P401// AE DS C TENSION SPRING (INCH SERIES) 引張バネ
71 0CW4A17384000 AN EG C PADDLE パドル
501 0CWXD32200102 AC DJ C PIN DOWEL 平行ピン
502 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス

– 17 –
G 搬送部 (Paper Feeder Assembly)

501 9
42
22
501
21
38
9
27
37
8 9
25
38 30
58 10
8 501
17
28 9
57 (PI3) 41
(CN55) 501 9
(PI5) 27 16
(CN36) 501
13
11
20
23
31 15
28 27
32 14
5
27 59 70
8
21 A
9
9
13
62 43 12
8 35
60 34
502 26
53 A
1 50
27 29 45
18 61 2 61
501 51
9 27 44 3
501 19
24 67
17 47
56 45
48 33
46
20
70 52
5 44
501
39 9 48
69
61
63

61
49
7 65 68
6 71
64
FCP08981
71
65 66

– 18 –
H 折り部 1/3 (Fold Assembly 1/3)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
6 0CW4A17299000 AG DX C SADDLE CAM FRONT サドルカム前
11 0CW4A17357000 AD DJ C PULLEY(27T) プーリー
17 0CW4A17363000 AH DX C SADDLE CAM REAR サドルカム後
18 0CW4A17364000 AL EB C GEAR(24T) ギア
20 0CW4A17376000 AF DS C GEAR(16T/42T) ギア
21 0CW4A17377000 AD DJ C GEAR(21T) ギア
22 0CW4A17385000 BN HZ C FOLD ROLLER ローラー
25 0CW4A17388000 AE DS C TENSION SPRING 引張バネ
30 0CW4A17533000 AC DJ C SPRING HOOK バネフック
32 0CW4A17552000 AF DS C BUSHING ブッシング
33 0CW4A17566000 AD DJ C CLIP SHAFT 軸クリップ
36 0CW4A17573000 AE DS C BUSHING ブッシング
38 0CW4A18330000 AD DJ C GEAR(18T) ギア
40 0CW4A18332000 AR EQ C PAPER DELIVERY GUIDE LOWER 排紙ガイド下
42 0CW4K14040000 BB GD B ELECTROMAGNETIC CLUTCH デンジクラッチ
44 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
46 0CWFC25827000 AE DJ C CLIP クリップ
48 0CWFS21672000 AD DJ C BUSHING ブッシング
50 0CW4A17476000 AC DJ C PLATE SPRING 板バネ
54 0CWWG85362000 AH DX B PHOTO INTERRUPTER(TLP1241) フォトインタラプタ
72 0CW4A17525000 AD DJ C ROLLER コロ
73 0CW4A17256000 AN EG C ROLLER SHAFT ローラー軸
74 0CW4A17504000 AF DS C HARNESS DUCT ハーネスダクト
75 0CW4A17485000 AK DX C TENSION BRACKET テンションブラケット
76 0CW4113K034// AU FG C FRAME REAR フレーム後
77 0CW4A17477000 AN EQ C TOP BRACKET トップブラケット
78 0CW4F11568010 AY FQ C FRAME FRONT フレーム前
79 0CW4A17227000 AT EZ C SHAFT CAM カムシャフト
80 0CW4A18323000 AC DJ C GUIDE PAD ガイドパッド
81 0CW4135P439// AF DJ C SPRING スプリング
82 0CWPW060050// AA DD C WASHER ポリスライダー
83 0CWXD21100502 AC DJ C E-RING E リング
502 0CWXD32200102 AC DJ C PIN DOWEL 平行ピン
505 0CWXD32300162 AC DJ C PIN DOWEL 平行ピン

– 19 –
H 折り部 1/3 (Fold Assembly 1/3)

46
72 32
25

82
73 38 83
46
81
33
36
72 82
82 44 75
76 44
80 48
44 42
74 54 502
46 11
(PI12)
(CN41)

30 (CL1)
(CN72)
25
77 48
32 21
46 48
80 (PI11)
(CN40) 54 46
20
See BLOCK
5-23
50
44

78 22 505
44
17
33

79
36
505
18
33
33
6
48 505
46

44
40

44 FCP08982

– 20 –
I 折り部 2/3 (Fold Assembly 2/3)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A17177000 AG DS C SWING GUIDE FRONT ヨウドウガイド前
2 0CW4A17178000 AG DS C SWING GUIDE REAR ヨウドウガイド後
4 0CW4A17295000 AD DJ C CAM FRONT カム前
5 0CW4A17296000 AD DJ C CAM REAR カム後
7 0CW4A17335000 AN EG C PULLEY(36T) プーリー
8 0CW4A17339000 AC DJ C FLANGE フランジ
10 0CW4A17350000 AC DJ C SADDLE SLIDER サドルスライダー
15 0CW4A17361000 AD DJ C ROLLER HOLDER ローラーホルダー
24 0CW4A17387000 AD DJ C TENSION SPRING 引張バネ
30 0CW4A17533000 AC DJ C SPRING HOOK バネフック
31 0CW4A17551000 AD DJ C WASHER ワッシャー
33 0CW4A17566000 AD DJ C CLIP SHAFT 軸クリップ
34 0CW4A17567000 AD DJ C CLIP SHAFT 軸クリップ
36 0CW4A17573000 AE DS C BUSHING ブッシング
37 0CW4A18329000 AC DJ C LINK ROLLER リンクコロ
39 0CW4A18331000 AD DJ C GEAR(17T) ギア
43 0CW4S19048000 AC DJ C SCREW STEPPED 段ビス
44 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
46 0CWFC25827000 AE DJ C CLIP クリップ
55 0CW4A18327000 AL EB C SPRING LEAF 板バネ
56 0CW4A18326000 AK DX C SPRING LEAF 板バネ
57 0CW4A17480000 AP EQ C DELIVERY PAPER GUIDE 排紙ガイド
58 0CW4A18324000 AE DS C REINFORCEMENT PLATE 補強板
59 0CW4A17322000 AD DJ C FOLD ROLLER 折りローラー
60 0CW4A17481000 AE DS C DELIVERY ROLLER HOLDER 排紙コロホルダー
68 0CW4A17297000 AC DJ C LINK ROLLER リンクコロ
71 0CW4A17228010 AC DJ C LINK SHAFT リンク軸
73 0CW4109P449// AD DJ C TENSION SPRING 引張バネ
74 0CW4A17298000 AF DS C SADDLE ROLLER サドルコロ
75 0CW4F11569000 AK DX C OPENER PLATE FRONT オープナ板前
76 0CW4F11570000 AK DX C OPENER PLATE REAR オープナ板後
77 0CW4A17181000 AG DX C COVER LINK カバーリンク
78 0CW4A17242000 AU FG C F-IN CAM SHAFT F-IN カム軸
79 0CW4A18325000 AN EG C BASE SPRING PLATE 板バネ
80 0CW4A17203010 AL EB C BASE BRACKET ベースブラケット
81 0CWXD21100402 AC DJ C E-RING E リング
82 0CWHW050FZS00 AB DJ C WASHER ワッシャー
83 0CW4A18328000 AC DJ C LINK PAD リンクパッド
84 0CW4A17180000 AN EG C SADDLE COVER サドルカバー
85 0CW4A17179000 AV FG C SADDLE PLATE サドル板
86 0CW4A17188000 AF DS C SADDLE PLATE SUB サドル板サブ
87 0CW4113K158A/ AS EQ C LEVER ASSY レバー Assy
88 0CW030060FZBI AA DD C SCREW(3×6) ビス
501 0CWXB12401005 AB DJ C SCREW(M4×10) ビス
503 0CWXD32200142 AC DJ C PIN DOWEL 平行ピン

– 21 –
I 折り部 2/3 (Fold Assembly 2/3)

36
77
36
503
5
15 83
31
33
58
78 C D
44
76
33 82 79
31 37 56
15 56
4 81 68 55
503 82 71 501
36 73
77 37 C D
36 71
81 74
SEE BLOCK
79 68 4-18
83
84 7
39
33
58 36
46
56 30 44 8
56
55
501 44 34
75 85 86
43
60 10
74 44 2
59
24
44
36
33
57 44
80
87
44
34

10
43
88
1
88
44
24 FCP08983

– 22 –
J 折り部 3/3 (Fold Assembly 3/3)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
3 0CW4A17290000 AE DS C GEAR(8T) ギア
9 0CW4A17340000 AG DX C GEAR(16T) ギア
12 0CW4A17358000 AP EQ C GEAR(16T/41T) ギア
13 0CW4A17359000 AK DX C GEAR(15T/38T) ギア
14 0CW4A17360000 AK DX C GEAR(24T) ギア
16 0CW4A17362000 AL EB C GEAR(24T) ギア
19 0CW4A17365000 AF DS C GEAR(16T) ギア
23 0CW4A17386000 AE DS C COMPRESSION SPRING 圧縮バネ
26 0CW4A17389000 AG DX C TENSION SPRING 引張バネ
27 0CW4A17403000 AE DS C TENSION SPRING 引張バネ
28 0CW4A17404000 AV FG C ROLLER ローラー
29 0CW4A17530000 AD DJ C PULLEY(27T) プーリー
34 0CW4A17567000 AD DJ C CLIP SHAFT 軸クリップ
35 0CWFC21175000 AC DJ C SCREW ビス
41 0CW4H16456000 AN EG C CABLE CONNECTING 中継束線
44 0CWFC22120000 AC DJ C SCREW(M4×7) ビス
45 0CW4H16450000 AT EZ E LED PWB UNIT LED 回路基板
46 0CWFC25827000 AE DJ C CLIP クリップ
47 0CWFS21615000 AS EZ C BALL BEARING ボールベアリング
48 0CWFS21672000 AD DJ C BUSHING ブッシング
49 0CWXF21607240 AN EG B BELT TIMING タイミングベルト
51 0CW4A17536000 AC DJ C SHAFT CLIP 軸クリップ
52 0CW4A17544000 AR EQ C FOLD ROLLER 折りローラー
53 0CW4A17545000 AQ EQ C FOLD ROLLER SUB 折りローラーサブ
61 0CW4A17187000 AK EB C FOLD ROLLER GUIDE 1 折りローラーガイド 1
62 0CW4A17309000 AE DJ C GUIDE HOLDER FRONT 1 ガイドホルダー前 1
63 0CW4A17310000 AE DJ C GUIDE HOLDER REAR 1 ガイドホルダー後 1
64 0CW4A17186010 AL EB C FOLD ROLLER GUIDE 2 折りローラーガイド 2
65 0CW4A17311000 AE DJ C GUIDE HOLDER FRONT 2 ガイドホルダー前 2
66 0CW4A17312000 AE DJ C GUIDE HOLDER REAR 2 ガイドホルダー後 2
67 0CW4A17207000 AR EQ C PAPER GUIDE UPPER ツウシガイド上
69 0CW4A17204000 AM EG C PAPER GUIDE LOWER ツウシガイド下
70 0CW4A18322000 AC DJ C LEAF EARTH SPRING アース板バネ
71 0CW4A17470000 AP EQ C SUB FRAME FRONT サブフレーム前
72 0CW4A17254000 AX FQ C FOLD SHAFT 1 折り部軸 1
73 0CW4A17255000 AY FQ C FOLD SHAFT 2 折り部軸 2
74 0CW4A17175000 AF DS C FOLD SUPPORT ROLLER PLATE FRONT 折りローラー支持板前
75 0CW4A17176000 AF DS C FOLD SUPPORT ROLLER PLATE REAR 折りローラー支持板後
76 0CW4A17492000 AF DS C BANDAGE COVER 目隠しカバー
502 0CWXD32200102 AC DJ C PIN DOWEL 平行ピン
504 0CWXD32300142 AD DJ C PIN DOWEL 平行ピン
506 0CWXD32300182 AC DJ C PIN DOWEL 平行ピン

– 23 –
J 折り部 3/3 (Fold Assembly 3/3)

(CN38) 29
35 502 46
(CN40) 48
45 34
(CN39) (CN41) 49
(PI10)
(CN39) 26
41
67 75
9
504 3
44 47
34

44
44
504
23
70 34
74 9
47 69 504
47
34 48 44 76 44
46
28
34

44 19
46
16 51
34 61

12

47 63
504 51
14 53
34
E
26 13 72 66
27
51 53
71
52 E
506 73
44
53
51
62
64
52
506
53

65 27 FCP08984

– 24 –
K ステイプル部 1/2 (Staple Assembly 1/2)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4A18206000 AD DJ C TENSION ROLLER テンションローラー
2 0CW4A18207000 AN EQ C TENSION SPRING 引張バネ
3 0CW4A18214000 AG DX D MOTOR COVER モーターカバー
5 0CW4A18217000 AE DS C CAM STOPPER 1 カムストッパ 1
10 0CW4A17592000 AE DJ C TORSION SPRING ネジリバネ
11 0CW4A18225000 AD DJ C PULLEY(38T) プーリー
13 0CW4A18904000 AF DS C STAPLE MOVABLE KNOB スティプル移動ノブ
17 0CW4A18905000 AH DX C JAM CLEANING KNOB JAM 処理ノブ
18 0CWFC30661000 AC DJ C CLIP クリップ
19 0CWFC15034000 AC DJ C SCREW W/WASHER(M3×6) バネ付ナベビス
21 0CW4S19076000 AC DJ C SCREW(M3×8) ビス
22 0CW4A18238000 AR EQ D FRONT COVER 前カバー
23 0CW4A18907000 AH DX D HANDLE COVER トッテカバー
26 0CW4A18240000 AQ EQ C PAPER COVER 紙ガイド
27 0CW4B10743000 AE DJ C COMPRESSION SPRING 圧縮バネ
28 0CW4A17581000 AF DS C PAPER GUIDE SUB 紙ガイド板サブ
29 0CW4A17584000 AD DJ C MARKER PIN 表示マーカーピン
31 0CW4A17583000 AD DJ C GEAR(42T) ギア
32 0CW4F11679000 AF DS C TENSION PLATE テンショナ板
33 0CWFC30779000 AC DJ C SCREW(M3×6) ビス
35 0CW4A18210000 AD DJ C PIN SLIDE スライドピン
36 0CW4A18198000 AC DJ C ROLLER コロ
41 0CW4H16506000 AW FG C CABLE STAPLER 2 スティプラ束線 2
42 0CW4K11070000 BE GN B STEPPING MOTOR ステッピングモーター
43 0CW4B10754000 AE DJ C FLANGE フランジ
44 0CW4B10744000 AE DJ C PULLEY プーリー
45 0CW4S10280000 AD DS C TENSION SPRING 引張バネ
46 0CW4F12053000 AH DX C PLATE STAPLE TENSION ステイプルテンショナ板
47 0CW4B10746000 AD DJ C TENSION ROLLER テンショナローラー
48 0CW4A18232000 AF DS C GEAR(18T/66T) ギア
49 0CWXF21804070 AQ EQ B BELT TIMING タイミングベルト
50 0CW4B10742000 AF DS C GUIDE ガイド
51 0CW4A17590000 AC DJ C STAPLE GUIDE PAD ステイプルガイドパッド
52 0CWRA22452000 AC DJ C BUSHING ブッシング
53 0CW4B10740000 AE DS C GEAR(16/29T) ギア
54 0CW040080FWWS AC DJ N C SCREW ビス
55 0CW4A18881000 AF DS C BUNDLE-WIRE GUIDE バンドルワイヤーガイド
56 0CW4A18211000 AD DJ C FPC GUIDE FPC ガイド
57 0CW4A18227000 AP EQ B BELT ベルト
58 0CW4135Q401// AE DJ N C STAPLE DRIVER SHEET ステイプルドライバーマイラー
501 0CWXD21100502 AC DJ C E-RING E リング
502 0CWXB12300605 AB DJ C SCREW(M3×6) ビス
503 0CWXB47401007 AB DJ C SCREW TAPPING(M4×10) タッピングビス
504 0CWXD21100642 AC DJ C E-RING E リング
505 0CWXB12400607 AB DJ C SCREW(M4×6) ビス
507 0CWXD32300142 AD DJ C PIN DOWEL 平行ピン

– 25 –
K ステイプル部 1/2 (Staple Assembly 1/2)

33 (M8)
(CN72)
3
55 19

42
(CN72)

41
5 21
502 32
33 (J1)
33
501
1

58 2
501 56
504
501
11
29 507
31 57
501

50
36
27
43 35
26
44
504
36
35
45
54 48
17
46 51
504
47
501 28
53
504 33
49 18
10
503 52
23
22
13
505 FCP08985

– 26 –
L ステイプル部 2/2 (Staple Assembly 2/2)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
4 0CW4A18215000 AF DS C COUPLING FRAME カップリングベース
6 0CW4A18218000 AF DS C COUPLING カップリング
7 0CW4A18219000 AF DS C COMPRESSION SPRING 圧縮バネ
8 0CW4A17591000 AF DS C STAPLE GUIDE ROLLER HOLDER スティプルガイドコロホルダー
9 0CW4A17589000 AD DJ C STAPLE GUIDE ROLLER スティプルガイドコロ
12 0CW4A18226000 AE DJ C GEAR(36T/38T) ギア
14 0CW4A18229000 AF DS C GEAR(42T/32T) ギア
15 0CW4A18230000 AE DJ C PULLEY(24T) プーリー
16 0CWXF21309000 AS EZ B BELT TIMING タイミングベルト
20 0CWFC25035000 AC DJ C SCREW W/WASHER(M3×6) バネ付ナベビス
24 0CW4A18265000 AE DS D SIDE COVER RIGHT サイドカバー右
25 0CW4A18264000 AE DS D SIDE COVER LEFT サイドカバー左
30 0CW4A18263000 AE DS D GEAR COVER ギアカバー
34 0CW4A18884000 BF GN E STAPLE CARTRIDGE UNIT スティプルカートリッジユニット
37 0CW4099K310// AM EG N E STAPLER BASE PWB ASSEMBLY スティプラベース回路基板
38 0CW4099K312// AP EQ N E STAPLER IN PWB ASSEMBLY スティプライン回路基板
39 0CW4H16504000 AK DX C CABLE STAPLER スティプラ束線
40 0CW4H16505000 AH DX C CABLE STAPLER 1 スティプラ束線 1
42 0CWXF21309000 AS EZ B BELT TIMING タイミングベルト
501 0CWXD21100502 AC DJ C E-RING E リング
504 0CWXD21100642 AC DJ C E-RING E リング
506 0CWXD32300122 AC DJ C PIN DOWEL 平行ピン
508 0CWXD32200142 AC DJ C PIN DOWEL 平行ピン

– 27 –
L ステイプル部 2/2 (Staple Assembly 2/2)

24
501

30
504
12
25 508

504
501 6
506
7

8
9
9
4 37

A (J2)

(J1) 39

506 34
14
42
504
16
506
15 38
504

A 20

(J2)

FCP08986 40

– 28 –
M 梱包 & 付属品 (Packing Material & Accessories)
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
0CW4144P901// BG GT N D PACKING CASE (JAPAN) パッキングケース
1
0CW4144P902// BG GT N D PACKING CASE (Other Countries) パッキングケース
2 0CW4144K600// BP LP N D STAPLE PAD アド
3 0CW4144P908// AL EB N D PACKING ADD SPC SPC ボードパッキング
4 0CW2216P524// AE DS D VINYL BAG A(HOLE) ビニール袋 A
7 0CW4144P909// AE DJ N D PACKING ADD PAD PAD ボードパッキング
8 0CW4088P220// AQ EQ D VINYL BAG ガゼット袋
9 0CW2158P380// AE DJ D HARNESS PACKING ハーネスパッキング
11 0CW4099P903// AL EB D JOINT パナジョイント
12 0CW4144P900// BQ LP N D PACKING PALLET パレット
13 0CW4110Q165// AL EB N D PACKING ADD パッキングアド
14 0CW2214P358// AB DJ D VINYL BAG(HS-1) ビニール袋
15 0CW4134P420// AF DS D OPERATION MANUAL 設置手順書
16 0CW61637///// AA DJ N D VINYL BAG C ビニール袋 C
17 0CW4144P364// AF DS N D PUNCH LABEL RSDF パンチラベル RSDF
18 0CW4144P363// AF DS N D PUNCH LABEL FIN パンチラベル FIN
19 0CW4144P362// AF DS N D STAPLE LABEL RSDF ステイプルラベル RSDF
20 0CW4144P361// AF DS N D STAPLE LABEL FIN ステイプルラベル FIN
21 0CW040180NBP/ AC DJ N C SCREW ビス
22 0CWSCR00045// AC DJ C SCREW ビス
23 0CW4099P913// AC DJ D PACKING MAT SD パッキングマット
24 0CW4144P911// AE DS N D PACKING ADD CVR CVR ボードパッキング
25 0CW4144P912// AE DJ N D PACKING ADD CVR アド
26 0CW4144P910// AQ EQ N D PACKING ADD DP DP ボードパッキング
27 0CW4099P912// AD DJ D MIRROR PAD(85×85) ミラマット
28 0CW4099P911// AC DJ D MIRROR PAD(80×80) ミラマット

– 29 –
M 梱包 & 付属品 (Packing Material & Accessories)
1

22
2

28 21

20 19 1817 4

16 3
28
16 15 4

23
14 7

2
24
25 13 2

7
7
2
25 8

26
9

27 11

11
2

11

12 FCP08987
11

– 30 –
N 梱包 & 付属品 (Packing Material & Accessories)[AR-PN1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW2111P021// AC DJ D VINYL BAG A ホールスルー袋 A
2 0CW1020K435// AY FQ D PAD SET パット組品 SH
3 0CW1020P832// AF DS D VINYL BAG E ポリ袋 E
4 0CW1020K375// AH DX D ASM-I/F HARNESS ASM-I/F ハーネス
5 0CW1020P827// AQ EQ D PACKING CASE パッキングケース
6 0CW1020K374// AN EG D ASM-POWER HARNESS ASM-POWER ハーネス
7 0CW040060FZTW AC DJ C SCREW ビス
8 0CW616371//// AA DJ D VINYL BAG C(80×120) ビニール袋 C
10 0CW4B10489000 AF DS D LABEL パンチクズステラベル
11 0CW4B10488000 AF DS D PUNCH POSITION LABEL(2-HOLE)
(FOR JAPAN AND EUROPE) パンチ位置ラベル
12 0CW4B10485000 AF DS D PUNCH POSITION LABEL(2/3-HOLE)
(FOR U.S.A,CANADA,AUSTRALIA AND NEW ZEALAND) パンチ位置ラベル
13 0CW4B10486000 AF DS D PUNCH POSITION LABEL(4-HOLE) (FOR EUROPE) パンチ位置ラベル
100 0CW1020P711B/ AK DX D INST. MANUAL パンチユニット設置手順書ペラ

N 梱包 & 付属品 (Packing Material & Accessories)[AR-PN1]

7 6
8 4
2
10
11 12 13

FCP08988

O DC コントローラー回路基板 (DC CONTROLLER PWB ASSEMBLY)


PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW32300048// AH DX N B EP-ROM(S-93C46BD0I-D8S1G) EP-ROM
2 0CWE312001475 AF DS B TRANSISTOR(2SK3495) トランジスター
3 0CWE321000945 AT EZ N B IC(A3984SLP) IC
4 0CWE323000494 AH DX N B IC(S-93C46BD0I-D8S1G) IC
5 0CWE323000483 AH DX N B IC(S-93C46BD0I-D8S1G) IC
6 0CWE73543M476 AD DJ C CAPACITOR(16CV47BS) コンデンサー
7 0CWE74566WE03 AD DJ N C CONNECTION(B3B-XH-A-LF) コネクター
8 0CWE74566WE04 AD DJ N C CONNECTION(B4B-XH-A-LF) コネクター
9 0CWE7709532// AF DS N B IC(TC7W32F) IC
(Unit)
901 0CW4144K302// CE UF N E DC CONTROLLER PWB ASSEMBLY DC コントローラー回路基板

– 31 –
P 前カバーユニット (FRONT COVER UNIT)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4145P019// BK HG N D Front cover フロントカバー
2 0CW040100FWBB AC DJ N C Screw(040100FWBB) ビス
3 0CW4145P319// AD DJ N C Ratch spring ラッチバネ
4 0CW4145P009// AE DS N C F cover ratch ラッチ
5 0CW4145P005// AE DS N C Cover sub ratch 取っ手リンクレバー
6 0CW4145P029// AH DX N C DF open link lever(PF4145P029) ユニット開閉リンクレバー
7 0CW020100SCH/ AA DD C Pin(φ2×10) ヘイコウピン
8 0CWNSCLP00008 AE DJ N C Clip 5(NS-CLP00008) 樹脂クリップ 5( 取手付 )
9 0CW4145P201// AU FG N C Ratch lever shaft フロントカバー支点軸
10 0CWNSCLP00005 AE DJ N C Clip 5(NS-CLP00005) 樹脂クリップ 5( 取手無 )
11 0CW4145P006// AP EQ N C F cover lever 取っ手

P 前カバーユニット (FRONT COVER UNIT)[MX-RBX1]

4
5 7
3 8
6

2 9 7
2
7
8

4
10

5
11

1
2 3

FCP09061

– 32 –
Q 搬送部 No1(TRANSPORT SECTION No.1)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4145P308// AF DS N D UF HDL label 上ガイド JAM 処理ラベル
2 0CW4145P306// AC DJ N C UF roller spring ピンチコロ線バネ
3 0CW4076P057// AF DS N C Pinch roller ピンチコロ
4 0CW4145P001// BQ LP N C UF guide 上ガイド
5 0CW4145P307// AC DJ N C UF flp cushion 上ガイドフラッパーダンパー
6 0CW4145P333// BA FX N C UF flapper 上ガイドフラッパー
7 0CW4145P343// AD DJ N C UF flp mylar マイラー
8 0CW4145P344// AD DJ N C UF flp cushion 1 上ガイドフラッパーダンパー 1
9 0CW4145P331// AD DJ N C UF cushion F5 上ガイドダンパー 5
10 0CW4145P329// AD DJ N C UF cushion F4 上ガイドダンパー 4
11 0CWNSBSH00002 AH DX N C Bearing 樹脂軸受
12 0CW4145P003// AE DJ N C UF flp arm フラッパーリンクレバー
13 0CWER040SKP// AB DD C E type ring 4 E リング 4
14 0CW4145P327// AR EQ N C UF cushion f2 上ガイドダンパー 2
15 0CW030100FWBB AC DJ N C Screw(M3×10) ビス
16 0CWHW030FNS// AC DJ N C Washer(HW-030) 平ワッシャー
17 0CW2214P393// AG DX C Magnet catch 13N マグネットキャッチ 13N
18 0CW4145P326// AG DX N C UF cushion F1 上ガイドダンパー 1
19 0CW4145P345// AD DJ N C UF flp cushion 2 上ガイドフラッパーダンパー 2

Q 搬送部 No1(TRANSPORT SECTION No.1)[MX-RBX1]

2
2
2
3 2 2
3 2
1
3
3 3
3

17
16
6
5
7
18 19
15 16
7 8
17
16 8

11
15 16 13 12

14 FCP09062
10 9

– 33 –
R 搬送部 No2(TRANSPORT SECTION No.2)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4145P321// AN EG N C Heatproof prevention sheet 耐熱防止シート
2 0CWNSSCR00226 AE DJ N C Screw(SCR03M040-D040015) ビス
3 0CW4145P341// AD DJ N C Heatproof prevention sheet 2 耐熱防止シート 2
4 0CW4145P109// AS EQ N C DCN guide 入口後コロユニットガイド
5 0CW4145P309// AG DX N C DCN up mylar マイラー
6 0CW4145P107// AH DX N C DCN f guide arm 入口後コロユニット前ブラケット
7 0CWNSBRG00110 AU EZ N C Bearing(NS-BRG00110) ベアリング
8 0CWER040SKP// AB DD C E type ring 4 E リング 4
10 0CW4145P202// AV FG N C DCN shaft 入口後コロ
11 0CW4145P108// AH DX N C DCN R guide arm 入口後コロユニット後ブラケット
12 0CWNSSCR00017 AD DJ N C Screw(NS-SCR00017) ビス
13 0CW040080FWWS AC DJ N C Screw(SCR040080FWWS) ビス
14 0CW4145P101// AN EG N C Positioning bracket 位置決めブラケット
15 0CWE450000384 AB DD C Edge suddle(EDS-2) エッジサドル
16 0CW4145K532// BA FX N C Harness-RELAY-UNIT(PF4145K532) ドロワハーネス
17 0CW030080FWBI AC DJ N C Screw(SCR-030-080) ビス
18 0CW4145P312// AG DX N C Earth spring(150-120-5000) ユニットアースバネ
19 0CW4145P205// AR EQ N C Positioning shaft 位置決め軸
21 0CW4145P104// AK DX N C UF hinge bracket 上ガイド支点ブラケット
22 0CW030060FWWS AC DJ N C Screw(SCR03M060-WS-W) ビス
23 0CW4145P015// AF DS N C DCN up lever 入口後コロユニット解除レバー
24 0CWNSCLP00005 AE DJ N C Clip 5(NS-CLP00005) 樹脂クリップ 5( 取手無 )
26 0CWHW030FNS// AC DJ N C Washer(HW-030) 平ワッシャー
27 0CW4145P004// AE DS N C UF solenoid lever ソレノイドリンクレバー
28 0CW4145P305// AD DJ N C Solenoid link spring(40-216-854) ソレノイドリンクバネ
29 0CW4145K552// BE GN N B Solenoid(TDS-12E-81A) フラッパーソレノイド
30 0CW4145P347// AE DJ C Cushion-SOL-P(PF4145P347) ソレノイドダンパー
31 0CW4145P103// AF DS N C Solenoid bracket ソレノイドブラケット
32 0CW030050FWWS AC DJ N C Screw(030050FWWS) ビス
33 0CW4145P324// AF DS N C Stopper band ストッパーバンド
34 0CW030100FWBB AC DJ N C Screw(M3×10) ビス
501 0CW4145K018// AG DS N E Hinge beracket 入口後コロユニット支点
カシメブラケット

R 搬送部 No2(TRANSPORT SECTION No.2)[MX-RBX1]


2 8
7
1 19
18
5
15
4 11
2 14 17
5 12 16 21
3 501
22
10 13 12
34 12
6 24
23
7
26 22
8 34 33
26 21

501

32
12
31 28
27

22
29 FCP09063
30
– 34 –
S 搬送部 No3(TRANSPORT SECTION No.3)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW4145P013// BS MW N D DF guide 下ガイド
2 0CW4145P315// AC DJ N C DCN down mylar 1 マイラー
3 0CW4145P336// AC DJ N C DF cushion 5-7 上ガイドフラッパーダンパー
4 0CW4145P028// AE DS N C Harness holder ハーネス押さえ
5 0CW4145P342// AD DJ N C DF solenoid cushion ソレノイドダンパー
6 0CW030100FWBB AC DJ N C Screw(M3×10) ビス
7 0CW4145K551// BD GN N B Fan(3110RL-05W-B39) ファンモーター
8 0CWNSSCR00087 AE DS N C Screw(NS-SCR00087) ビス
9 0CW4145P030// AH DX N C DF sensor lever 紙パスセンサーレバー
10 0CW4145P338// AD DJ N C Sensor spring(30-214-34) 紙パスセンサーバネ
11 0CW4145K021// AZ FQ N C Rear frame bracket リア側板カシメブラケット
12 0CWNSBRG00110 AU EZ N C Bearing(NS-BRG00110) ベアリング
13 0CWER040SKP// AB DD C E type ring 4 E リング 4
14 0CW4145P110// AG DS N C Pas sensor bracket 紙パスセンサーブラケット
15 0CWE314000784 AP EQ N B Sensor(E314000784)(GP1S73P2J00F) センサー
16 0CWNSSCR00017 AD DJ N C Screw ビス
17 0CW4145P311// AS EZ N C Motor out joint ワンウェイジョイント
18 0CW4145P026// AE DS N C Pulley プーリー
19 0CWNSBLT00338 AS EQ N B Belt(NS-BLT00338) タイミングベルト
20 0CWER050SKP// AA DD C E type ring 5 E リング 5
21 0CW4145P035// AE DJ N C Pulley(S3M-16) プーリー
22 0CW2268P076// AD DJ C Flange 樹脂フランジ
23 0CWNSBLT00339 AR EQ N B Belt(S3M068040) タイミングベルト
24 0CW4145P010// AF DS N C Pulley(S3M-16-25) プーリー
25 0CWNSBLT00333 AS EQ N B Belt(S3M054040) タイミングベルト
26 0CW040100FWBB AC DJ N C Screw(040100FWBB) ビス
27 0CW030060FWWS AC DJ N C Screw(030060FWWS) ビス
28 0CW4145K550// BL HL N B Drive motor(PF4145K550) 駆動モーター
29 0CW020100SCH/ AA DD C Pin(φ2×10) ヘイコウピン
30 0CW4145P300// AY FQ N C DF in delivery roller 入口搬送ローラ
31 0CW4145P303// AZ FX N C DF dcn delivery roller 排紙搬送ローラ
32 0CW4145P301// BA FX N C DF out delivery roller 1 入口後搬送ローラ 1
33 0CW4145P302// AY FQ N C DF out delivery roller 2 排紙前搬送ローラ 2
34 0CW4145P025// BQ LP N D Bottom cover 底カバー
35 0CW4145K020// AZ FX N C Front frame bracket フロント側板カシメブラケット
36 0CWWT25035000 AD DJ C Edge saddle(EDS-0607M) エッジサドル
37 0CWPW060025// AA DJ C Poliyslider ポリスライダー
38 0CW4145P317// AD DJ N C Spring(73-100-6000) ローラガタ止めバネ
39 0CWE450001148 AE DS N C HARENSS CLAMP(RLMC-05T V0) ハーネスクランプ
40 0CWE450001128 AC DJ C Wire band(RSG-100) ワイヤーバンド

– 35 –
S 搬送部 No3(TRANSPORT SECTION No.3)[MX-RBX1]

2 2 20
18 19
1 17 20
3 10 13
12 21
13 22
9 12
40 39 23
24
4 15 26 12 25
16 39
5 13
3 6 10 12 40
4 11 14
4 26 40 15
4 6 9
6 6 26 14
33 29 16
39
8 8 32
7
37 12
38 29 31 29
21
37 29 27
20 28
21
12 30 26
19 38
34
20
26 26 26 35

12 36
37
38

26 26 26
20 12
37 26
38 26 FCP09064

– 36 –
T 排紙トレイ & レール部 (DELIVERY PAPER TARY & RAIL SECTION)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
1 0CW040080FWBP AC DJ N C Screw(SCR-040-080WBP) ビス
2 0CW4145P012// BH GX N D Left cover 左カバー
4 0CW4145P017// AG DX N C Lock hfs holder フィニッシャーラッチ受け
6 0CW4145P032// AE DS N C UF holder 上ガイド押さえ
7 0CW4145K010// BH GX N C Left frame bracket 左レールカシメブラケット
9 0CW4145P502// AR EQ N C Screw(JFS-2.6S-B1WM) IF コネクター固定ネジ
10 0CW4145P018// BL HG N C Reverse tray 反転トレイ
11 0CWNSCLP00008 AE DJ N C Clip 8(050140W) 樹脂クリップ 8
12 0CWNSCLP00005 AE DJ N C Clip 5(050060W) 樹脂クリップ 5
13 0CWNSBSH00002 AH DX N C Bearing 樹脂軸受
15 0CW4145P024// AE DS N C Reverse flp link lever 反転フラッパーリンクレバー
16 0CW4145P124// AG DX N C Reverse tray bracket 反転トレイ補強ブラケット
17 0CW030100FWBB AC DJ N C Screw(030100FWBB) ビス
18 0CW4145P351// AG DX N C Screw(SCR-040-060-D-CO1N-1) 反転トレイ固定ネジ
19 0CW4145P334// BA FX N C Reverse flapper 反転フラッパー
20 0CW4145P346// AD DJ N C Reverse tray cushion 反転トレイダンパー
21 0CWNSSCR00017 AD DJ N C Screw(NS-SCR00017) ビス
22 0CW4145P121// AN EG N C Pntrance guide 入口ガイド
23 0CW4145P033// AG DS N C Sensor lever 本体排紙センサーレバー
24 0CW4145P105// BF GN N C Right rail 右レール
25 0CW4141P082// AF DS N C Frame holder 本体シフター押さえ
27 0CW4145P034// AR EQ N C Right rail stopper 右レールたわみ防止
28 0CW4145P016// AE DJ N C Rail collar レール用コロ
29 0CWER050SKP// AA DD C E type ring 5 E リング 5
31 0CW4145P123// AG DX N C Sensor bracket ユニット開閉センサーブラケット
32 0CWE314000784 AP EQ N B Sensor(GP1S73P2J00F) センサー
33 0CW4111P349// AD DJ N C Screw ビス
34 0CW4145P116// AR EQ N C Drawer bracket ドロワブラケット
35 0CWE450001139 AC DJ C Clamp(E450001139) クランプ
36 0CWNSSCR00225 AC DJ N C Screw(SCR03M030-D040020) ビス
37 0CW4145P313// AE DJ N C Drawer spring ドロワバネ
38 0CWE75317BK22 BB GD N C Drawer connector(5-292178-1) ドロワコネクタ
39 0CW4145P112// AX FG N C Left rail bracket 左レールサブブラケット
40 0CW4145P027// AG DX N C Stopper ユニットストッパー
41 0CW4145P031// AE DS N C Open sensor lever ユニット開閉センサーレバー
42 0CW4145P330// AE DJ N C Stopper spring ユニットストッパーバネ
43 0CW4141P368// AF DS N C Mylar マイラー
44 0CWE450001128 AC DJ C Wire band(RSG-100) ワイヤーバンド
45 0CWE450001297 AH DX N C CLIP(RES-6) クリップ
46 0CW4145K510// BL HL N E Relay1 PWB unit(PF4145K510) 中継基板組
47 0CW4145K534// AN EG N C Harness-OPEN-SEN(PF4145K534) ハーネス
48 0CW4145K533// AK DX N C Harness-OPEN(PF4145K533) ハーネス
49 0CW4145K531// AS EQ N C Harness-RELAY1(PF4145K531) ハーネス
50 0CW4145K535// AR EQ N C Harness-RELAY2(PF4145K535) ハーネス
51 0CW4145K532// BA FX N C Harness-RELAY-UNIT(PF4145K532) ドロワハーネス
52 0CW4145P336// AC DJ N C DF cushion 5-7 上ガイドフラッパーダンパー
53 0CWE450000384 AB DD C Edge saddle(EDS-2) エッジサドル
54 0CWE74561WE03 AE DS N C Connector(292254-3) 中継コネクタ

– 37 –
T 排紙トレイ & レール部 (DELIVERY PAPER TARY & RAIL SECTION)[MX-RBX1]

45
1
9
48 46
10
1 11
2 45 13
49
1 51 12
50 53 36
53 37

4
37
38 16
11
1 6 7 35
54 20 15 52
34 17
18
33 19
17
4 52 21
39
1 22
23
40 21 21
24
12 21
21 44
42
41 21
28 31 43
29 29
28
32 44
1 25
47 27 FCP09065
44

– 38 –
U 梱包 & 付属品 (PACKING MATERIAL & ACCESSORIES)[MX-RBX1]
PRICE RANK NEW PART
NO. PARTS CODE Ex. Ja. MARK RANK DESCRIPTION
0CW4145P401// BH GX N D Packing case(for JAPAN) 個装ケース
1
0CW4145P407// BF GN N D Packing case(except JAPAN) 個装ケース
3 0CW2216P524// AE DS D Vinyl bag(470×800mm) ビニールブクロ A ( アナアキ )
5 0CW2148P093// AG DX D Vinyl bag(900×800mm) ビニールブクロ アナアキ
9 0CW616371//// AA DJ D Vinyl bag C(80×120mm) ビニールブクロ C
11 0CW4134P420// AF DS D Operation manual 設置手順書
13 0CW040080FWBP AC DJ N C Screw(040080FWBP) ビス
14 0CW4145P351// AG DX N C Screw 反転トレイ固定ネジ
15 0CW4145P034// AR EQ N C Right rail stopper 右レールたわみ防止
16 0CW4145P033// AG DS N C Sensor lever 本体排紙センサーレバー

U 梱包 & 付属品 (PACKING MATERIAL & ACCESSORIES)[MX-RBX1]

13
14 15 16

13
11
9
3
3

1
FCP09066

– 39 –
■ 索引 (Index) PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R
PRICE R. 0CW4113P243// 9- 9 AE DS C
PARTS CODE NO. Ex. Ja.
NEW P/R
0CW4113P352// 11- 49 AG DX C
[0] 0CW4113P643B/ 11- 35 AR EQ C
0CW020100SCH/ 20- 7 AA DD C 0CW4114P048B/ 10- 23 AU EZ C
" 23- 29 AA DD C 0CW4114P352// 11- 33 AH DX N C
0CW030050FWWS 22- 32 AC DJ N C 0CW4114P401// 11- 70 AE DJ C
0CW030060FWWS 22- 22 AC DJ N C 0CW4114P813// 11- 24 AF DS C
" 23- 27 AC DJ N C 0CW4116P405B/ 4- 38 BA FX C
0CW030060FZBI 13- 88 AA DD C 0CW4116P492// 9- 17 AL EB C
0CW030080FDBB 5- 29 AB DJ N C 0CW4116P759// 11- 38 AN EG C
0CW030080FWBI 22- 17 AC DJ N C 0CW4134K328// 4- 37 AF DS C
0CW030100FWBB 21- 15 AC DJ N C 0CW4134P042// 1- 51 AN EQ D
" 22- 34 AC DJ N C 0CW4134P401// 11- 70 AE DS C
" 23- 6 AC DJ N C 0CW4134P420// 17- 15 AF DS D
" 24- 17 AC DJ N C " 25- 11 AF DS D
0CW040060FNBI 2- 80 AA DD C 0CW4135K550// 7- 6 BD GN B
0CW040060FZTW 18- 7 AC DJ C 0CW4135P439// 12- 81 AF DJ C
0CW040080FWBP 24- 1 AC DJ N C 0CW4135Q401// 15- 58 AE DJ N C
" 25- 13 AC DJ N C 0CW4139P139// 11- 57 AR FG C
0CW040080FWWS 15- 54 AC DJ N C 0CW4141P082// 24- 25 AF DS N C
" 22- 13 AC DJ N C 0CW4141P368// 24- 43 AF DS N C
0CW040080FZWS 1- 601 AA DD C 0CW4144K100// 1- 10 BK HC N C
0CW040100FNBI 1- 58 AA DD C 0CW4144K146// 5- 26 AW FG N E
0CW040100FWBB 20- 2 AC DJ N C 0CW4144K302// 19- 901 CE UF N E
" 23- 26 AC DJ N C " 4- 46 CE UF N E
0CW040100FWWS 2- 72 AC DJ N C 0CW4144K501// 2- 57 BC GJ N C
0CW040120FNBB 1- 57 AB DJ C 0CW4144K502// 2- 5 BA FX N C
" 2- 79 AB DJ C 0CW4144K600// 17- 2 BP LP N D
0CW040180NBP/ 17- 21 AC DJ N C 0CW4144P002// 1- 52 AP EQ N C
0CW0412FNBIT2 2- 74 AC DJ N C 0CW4144P003// 1- 53 AL EB N C
0CW1020K363B/ 6- 16 AX FG E 0CW4144P004// 1- 4 BA FX N C
0CW1020K365B/ 6- 17 AX FG E 0CW4144P005// 1- 38 AU FG N C
0CW1020K367// 5- 11 AP EQ N E 0CW4144P007// 2- 70 AG DX N C
0CW1020K369// 5- 12 AP EQ N E 0CW4144P016// 3- 48 AG DX N C
0CW1020K374// 18- 6 AN EG D 0CW4144P053// 10- 69 AP EQ N C
0CW1020K375// 18- 4 AH DX D 0CW4144P100// 2- 69 AZ FQ N C
0CW1020K435// 18- 2 AY FQ D 0CW4144P200// 2- 22 BF GN N D
0CW1020P280A/ 5- 54 AH DX C 0CW4144P201// 2- 23 BE GN N D
0CW1020P537A/ 5- 50 BS MJ B 0CW4144P202// 2- 2 BK HG N D
0CW1020P711B/ 18- 100 AK DX D 0CW4144P203// 2- 17 BB GD N D
0CW1020P827// 18- 5 AQ EQ D 0CW4144P204// 2- 61 BC GD N D
0CW1020P832// 18- 3 AF DS D 0CW4144P205// 2- 16 AK EB N D
0CW1033K300// 6- 14 BD GN N B 0CW4144P206// 2- 7 BA FX N D
0CW2111P021// 18- 1 AC DJ D 0CW4144P207// 2- 62 AR EQ N C
0CW2148P093// 25- 5 AG DX D 0CW4144P208// 2- 63 AN EQ N D
0CW2158P380// 17- 9 AE DJ D 0CW4144P209// 2- 65 AP EQ N D
0CW2214P358// 17- 14 AB DJ D 0CW4144P210// 2- 4 AL EB N D
0CW2214P393// 21- 17 AG DX C 0CW4144P211// 2- 64 AH DX N C
0CW2216P524// 17- 4 AE DS D 0CW4144P212// 3- 15 AG DX N C
" 25- 3 AE DS D 0CW4144P213// 2- 33 BC GJ N C
0CW2268P076// 23- 22 AD DJ C 0CW4144P214// 2- 73 AP EQ N D
0CW3090P360// 2- 75 AD DJ C 0CW4144P215// 4- 24 AL EB N C
0CW32300048// 19- 1 AH DX N B 0CW4144P216// 2- 67 AF DS N C
0CW4048P076// 2- 82 AD DJ N C 0CW4144P217// 2- 56 AE DS N C
0CW4048P300// 4- 39 AC DJ C 0CW4144P220// 2- 76 AH DX N D
0CW4060P027// 10- 9 AB DJ N C 0CW4144P222// 2- 77 AH DX N D
" 4- 16 AB DJ N C 0CW4144P235// 2- 11 BA FX N D
" 9- 21 AB DJ N C 0CW4144P245// 5- 27 AS EZ N C
0CW4076P057// 21- 3 AF DS N C 0CW4144P250// 1- 46 BD GN N D
0CW4088P220// 17- 8 AQ EQ D 0CW4144P251// 1- 24 BC GJ N D
0CW4099K310// 16- 37 AM EG N E 0CW4144P252// 1- 56 AM EG N C
0CW4099K312// 16- 38 AP EQ N E 0CW4144P253// 1- 14 BC GD N D
0CW4099P903// 17- 11 AL EB D 0CW4144P254// 1- 47 BF GN N D
0CW4099P911// 17- 28 AC DJ D 0CW4144P277// 10- 38 AG DX N D
0CW4099P912// 17- 27 AD DJ D 0CW4144P284// 10- 41 AG DX N D
0CW4099P913// 17- 23 AC DJ D 0CW4144P289// 10- 35 AR EQ N C
0CW4099Q031// 2- 71 AD DJ N C 0CW4144P290// 10- 32 AR EQ N C
0CW4109P207// 3- 68 AD DJ N C 0CW4144P303// 10- 8 AL EB N D
0CW4109P231// 11- 6 AD DJ C 0CW4144P314// 4- 23 AD DJ N C
0CW4109P232// 11- 7 AD DJ C 0CW4144P361// 17- 20 AF DS N D
0CW4109P247// 3- 1 AY FQ N C 0CW4144P362// 17- 19 AF DS N D
0CW4109P248// 3- 13 AV FG N C 0CW4144P363// 17- 18 AF DS N D
0CW4109P427// 3- 67 AC DJ N C 0CW4144P364// 17- 17 AF DS N D
0CW4109P449// 13- 73 AD DJ C 0CW4144P381// 2- 34 AK EB N C
0CW4110P026// 2- 86 AM EG N C 0CW4144P391// 2- 10 BA FX N C
0CW4110P362// 11- 64 AD DJ C 0CW4144P393// 2- 30 AS EQ N D
0CW4110Q165// 17- 13 AL EB N D 0CW4144P394// 2- 31 AX FG N D
0CW4111P349// 24- 33 AD DJ N C 0CW4144P400// 3- 9 AD DJ N C
0CW4113K034// 12- 76 AU FG C 0CW4144P401// 2- 68 AH DX N C
0CW4113K158A/ 13- 87 AS EQ C 0CW4144P402// 2- 85 AE DS N C
0CW4113P027A/ 2- 78 AK DX C 0CW4144P408// 10- 70 AF DS N C

– 40 –
PRICE R. PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R PARTS CODE NO. Ex. Ja.
NEW P/R

0CW4144P433// 2- 40 AY FQ N D 0CW4145P306// 21- 2 AC DJ N C


0CW4144P445// 5- 28 AH DX N C 0CW4145P307// 21- 5 AC DJ N C
0CW4144P469// 2- 84 BC GJ N B 0CW4145P308// 21- 1 AF DS N D
0CW4144P705// 4- 1 AL EB N D 0CW4145P309// 22- 5 AG DX N C
0CW4144P726// 2- 3 AY FQ N D 0CW4145P311// 23- 17 AS EZ N C
0CW4144P727// 2- 26 BE GN N C 0CW4145P312// 22- 18 AG DX N C
0CW4144P728// 2- 27 BA FX N C 0CW4145P313// 24- 37 AE DJ N C
0CW4144P751// 4- 27 AG DX N C 0CW4145P315// 23- 2 AC DJ N C
0CW4144P763// 2- 9 AT EZ N C 0CW4145P317// 23- 38 AD DJ N C
0CW4144P900// 17- 12 BQ LP N D 0CW4145P319// 20- 3 AD DJ N C
0CW4144P901// 17- 1 BG GT N D 0CW4145P321// 22- 1 AN EG N C
0CW4144P902// 17- 1 BG GT N D 0CW4145P324// 22- 33 AF DS N C
0CW4144P908// 17- 3 AL EB N D 0CW4145P326// 21- 18 AG DX N C
0CW4144P909// 17- 7 AE DJ N D 0CW4145P327// 21- 14 AR EQ N C
0CW4144P910// 17- 26 AQ EQ N D 0CW4145P329// 21- 10 AD DJ N C
0CW4144P911// 17- 24 AE DS N D 0CW4145P330// 24- 42 AE DJ N C
0CW4144P912// 17- 25 AE DJ N D 0CW4145P331// 21- 9 AD DJ N C
0CW4144P950// 2- 83 AC DJ N C 0CW4145P333// 21- 6 BA FX N C
0CW4145K010// 24- 7 BH GX N C 0CW4145P334// 24- 19 BA FX N C
0CW4145K018// 22- 501 AG DS N E 0CW4145P336// 23- 3 AC DJ N C
0CW4145K020// 23- 35 AZ FX N C " 24- 52 AC DJ N C
0CW4145K021// 23- 11 AZ FQ N C 0CW4145P338// 23- 10 AD DJ N C
0CW4145K510// 24- 46 BL HL N E 0CW4145P341// 22- 3 AD DJ N C
0CW4145K531// 24- 49 AS EQ N C 0CW4145P342// 23- 5 AD DJ N C
0CW4145K532// 22- 16 BA FX N C 0CW4145P343// 21- 7 AD DJ N C
" 24- 51 BA FX N C 0CW4145P344// 21- 8 AD DJ N C
0CW4145K533// 24- 48 AK DX N C 0CW4145P345// 21- 19 AD DJ N C
0CW4145K534// 24- 47 AN EG N C 0CW4145P346// 24- 20 AD DJ N C
0CW4145K535// 24- 50 AR EQ N C 0CW4145P347// 22- 30 AE DJ C
0CW4145K550// 23- 28 BL HL N B 0CW4145P351// 24- 18 AG DX N C
0CW4145K551// 23- 7 BD GN N B " 25- 14 AG DX N C
0CW4145K552// 22- 29 BE GN N B 0CW4145P401// 25- 1 BH GX N D
0CW4145P001// 21- 4 BQ LP N C 0CW4145P407// 25- 1 BF GN N D
0CW4145P003// 21- 12 AE DJ N C 0CW4145P502// 24- 9 AR EQ N C
0CW4145P004// 22- 27 AE DS N C 0CW4A12609000 1- 44 AC DJ C
0CW4145P005// 20- 5 AE DS N C 0CW4A17172010 4- 10 AN EQ C
0CW4145P006// 20- 11 AP EQ N C 0CW4A17173000 7- 16 AD DJ C
0CW4145P009// 20- 4 AE DS N C 0CW4A17175000 14- 74 AF DS C
0CW4145P010// 23- 24 AF DS N C 0CW4A17176000 14- 75 AF DS C
0CW4145P012// 24- 2 BH GX N D 0CW4A17177000 13- 1 AG DS C
0CW4145P013// 23- 1 BS MW N D 0CW4A17178000 13- 2 AG DS C
0CW4145P015// 22- 23 AF DS N C 0CW4A17179000 13- 85 AV FG C
0CW4145P016// 24- 28 AE DJ N C 0CW4A17180000 13- 84 AN EG C
0CW4145P017// 24- 4 AG DX N C 0CW4A17181000 13- 77 AG DX C
0CW4145P018// 24- 10 BL HG N C 0CW4A17184000 9- 20 AN EG C
0CW4145P019// 20- 1 BK HG N D 0CW4A17186010 14- 64 AL EB C
0CW4145P024// 24- 15 AE DS N C 0CW4A17187000 14- 61 AK EB C
0CW4145P025// 23- 34 BQ LP N D 0CW4A17188000 13- 86 AF DS C
0CW4145P026// 23- 18 AE DS N C 0CW4A17191000 10- 52 AF DS C
0CW4145P027// 24- 40 AG DX N C 0CW4A17192000 11- 58 AE DS C
0CW4145P028// 23- 4 AE DS N C 0CW4A17193000 10- 56 AG DS C
0CW4145P029// 20- 6 AH DX N C 0CW4A17194000 11- 31 AR EQ C
0CW4145P030// 23- 9 AH DX N C 0CW4A17195000 2- 20 AF DS C
0CW4145P031// 24- 41 AE DS N C 0CW4A17196000 10- 60 AH DX C
0CW4145P032// 24- 6 AE DS N C 0CW4A17198000 8- 30 AQ EQ C
0CW4145P033// 24- 23 AG DS N C 0CW4A17199000 8- 26 AE DJ C
" 25- 16 AG DS N C 0CW4A17202000 11- 62 AK DX C
0CW4145P034// 24- 27 AR EQ N C 0CW4A17203010 13- 80 AL EB C
" 25- 15 AR EQ N C 0CW4A17204000 14- 69 AM EG C
0CW4145P035// 23- 21 AE DJ N C 0CW4A17207000 14- 67 AR EQ C
0CW4145P101// 22- 14 AN EG N C 0CW4A17209000 10- 31 AC DJ C
0CW4145P103// 22- 31 AF DS N C 0CW4A17212000 10- 42 AE DS C
0CW4145P104// 22- 21 AK DX N C 0CW4A17217000 3- 57 AV FG C
0CW4145P105// 24- 24 BF GN N C 0CW4A17227000 12- 79 AT EZ C
0CW4145P107// 22- 6 AH DX N C 0CW4A17228010 13- 71 AC DJ C
0CW4145P108// 22- 11 AH DX N C 0CW4A17229000 8- 28 AL EB C
0CW4145P109// 22- 4 AS EQ N C 0CW4A17231000 8- 29 AL EB C
0CW4145P110// 23- 14 AG DS N C 0CW4A17234000 11- 60 AR EQ C
0CW4145P112// 24- 39 AX FG N C 0CW4A17236000 10- 54 AS EQ C
0CW4145P116// 24- 34 AR EQ N C 0CW4A17237000 11- 63 AT EZ C
0CW4145P121// 24- 22 AN EG N C 0CW4A17238000 11- 67 AR EQ C
0CW4145P123// 24- 31 AG DX N C 0CW4A17239000 10- 50 AK DX C
0CW4145P124// 24- 16 AG DX N C 0CW4A17240000 9- 7 AM EG C
0CW4145P201// 20- 9 AU FG N C 0CW4A17242000 13- 78 AU FG C
0CW4145P202// 22- 10 AV FG N C 0CW4A17253000 3- 59 AS EZ C
0CW4145P205// 22- 19 AR EQ N C 0CW4A17254000 14- 72 AX FQ C
0CW4145P300// 23- 30 AY FQ N C 0CW4A17255000 14- 73 AY FQ C
0CW4145P301// 23- 32 BA FX N C 0CW4A17256000 12- 73 AN EG C
0CW4145P302// 23- 33 AY FQ N C 0CW4A17259000 3- 3 AD DJ C
0CW4145P303// 23- 31 AZ FX N C 0CW4A17260000 7- 1 AF DS C
0CW4145P305// 22- 28 AD DJ N C 0CW4A17261000 7- 2 AG DS C

– 41 –
PRICE R. PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R PARTS CODE NO. Ex. Ja.
NEW P/R

0CW4A17262000 7- 3 AE DS C 0CW4A17362000 14- 16 AL EB C


0CW4A17263000 7- 4 AE DS C 0CW4A17363000 12- 17 AH DX C
0CW4A17264000 7- 13 AE DJ C 0CW4A17364000 12- 18 AL EB C
0CW4A17265000 3- 29 AC DJ C 0CW4A17365000 14- 19 AF DS C
0CW4A17266000 10- 62 AE DS C 0CW4A17366000 11- 23 AE DJ C
0CW4A17270000 2- 32 AG DS C 0CW4A17367000 9- 11 AD DJ C
0CW4A17271000 11- 10 AP EQ C 0CW4A17368000 10- 17 AP EQ C
0CW4A17272000 11- 11 AN EQ C 0CW4A17371000 3- 8 AC DJ C
0CW4A17273000 10- 15 AD DJ C " 4- 14 AC DJ C
0CW4A17274000 11- 12 AD DJ C " 9- 5 AC DJ C
0CW4A17275000 10- 27 AD DJ C 0CW4A17372000 11- 26 AH DX C
0CW4A17276000 11- 13 AC DJ C 0CW4A17376000 12- 20 AF DS C
0CW4A17278000 11- 1 AC DJ C 0CW4A17377000 12- 21 AD DJ C
0CW4A17279000 11- 14 AD DJ C 0CW4A17378000 2- 15 AD DJ C
0CW4A17280000 11- 15 AD DJ C 0CW4A17379000 11- 48 AS EQ C
0CW4A17281000 11- 2 AD DJ C 0CW4A17380000 2- 58 AD DJ C
0CW4A17282000 11- 45 AC DJ C 0CW4A17381000 10- 18 AS EQ C
0CW4A17283000 11- 44 AC DJ C 0CW4A17383000 10- 6 AY FQ B
0CW4A17284000 2- 41 AD DJ C 0CW4A17384000 11- 71 AN EG C
0CW4A17285000 11- 50 AE DS C 0CW4A17385000 12- 22 BN HZ C
0CW4A17286000 11- 46 AE DS C 0CW4A17386000 14- 23 AE DS C
0CW4A17288000 3- 24 AD DJ C 0CW4A17387000 13- 24 AD DJ C
0CW4A17289000 9- 8 AF DS C 0CW4A17388000 12- 25 AE DS C
0CW4A17290000 14- 3 AE DS C 0CW4A17389000 14- 26 AG DX C
0CW4A17291000 2- 12 AE DS C 0CW4A17390000 10- 1 AD DJ C
0CW4A17295000 13- 4 AD DJ C 0CW4A17391000 10- 39 AC DJ C
0CW4A17296000 13- 5 AD DJ C 0CW4A17392000 10- 7 AE DS C
0CW4A17297000 13- 68 AC DJ C 0CW4A17400000 2- 35 AC DJ C
0CW4A17298000 13- 74 AF DS C " 3- 45 AC DJ C
0CW4A17299000 12- 6 AG DX C 0CW4A17401000 11- 5 AD DJ C
0CW4A17300000 8- 16 AD DJ C 0CW4A17402000 10- 25 AC DJ C
0CW4A17301000 8- 1 AE DS C 0CW4A17403000 14- 27 AE DS C
0CW4A17302000 8- 2 AQ EQ C 0CW4A17404000 14- 28 AV FG C
0CW4A17303000 8- 3 AK DX C 0CW4A17406000 11- 34 AH DX C
0CW4A17304000 8- 4 AL EB C 0CW4A17407000 8- 21 AD DJ C
0CW4A17305000 8- 5 AL EB C 0CW4A17408000 2- 36 AD DJ C
0CW4A17306000 8- 6 AH DX C 0CW4A17409000 4- 34 AD DJ C
0CW4A17307000 8- 7 AF DS C 0CW4A17414000 3- 10 AD DJ C
0CW4A17308000 8- 18 AS EZ C 0CW4A17415000 2- 14 AG DS C
0CW4A17309000 14- 62 AE DJ C 0CW4A17416000 9- 3 AD DJ C
0CW4A17310000 14- 63 AE DJ C 0CW4A17417000 3- 11 AD DJ C
0CW4A17311000 14- 65 AE DJ C 0CW4A17418000 4- 12 AD DJ C
0CW4A17312000 14- 66 AE DJ C 0CW4A17419000 3- 12 AD DJ C
0CW4A17314000 10- 36 AH DX D 0CW4A17421000 9- 12 AE DJ C
0CW4A17317000 2- 21 AC DJ C 0CW4A17422000 9- 13 AE DS C
0CW4A17318000 3- 31 AK DX C 0CW4A17423000 9- 14 AE DS C
0CW4A17319000 10- 40 AL EB C 0CW4A17424000 2- 29 AF DS C
0CW4A17321000 3- 44 AR EQ C 0CW4A17425000 4- 48 AE DS C
0CW4A17322000 13- 59 AD DJ C 0CW4A17426000 4- 47 AH DX C
0CW4A17325000 9- 10 AE DS C 0CW4A17427000 11- 32 AT EZ C
0CW4A17327000 9- 18 AD DJ C 0CW4A17467000 4- 40 AF DS C
0CW4A17328000 10- 5 AD DJ C 0CW4A17469000 7- 14 AD DJ C
0CW4A17329000 10- 24 AE DS C 0CW4A17470000 14- 71 AP EQ C
0CW4A17330000 11- 16 AD DJ C 0CW4A17474000 3- 64 AG DS C
0CW4A17331000 11- 17 AD DJ C 0CW4A17475000 3- 66 AH DX C
0CW4A17332000 11- 18 AC DJ C 0CW4A17476000 12- 50 AC DJ C
0CW4A17333000 11- 43 AN EG C 0CW4A17477000 12- 77 AN EQ C
0CW4A17335000 13- 7 AN EG C 0CW4A17479000 8- 24 AD DJ C
0CW4A17337000 11- 3 AE DS C 0CW4A17480000 13- 57 AP EQ C
0CW4A17338000 8- 8 AH DX C 0CW4A17481000 13- 60 AE DS C
0CW4A17339000 11- 25 AC DJ C 0CW4A17482000 3- 54 AP EQ C
" 13- 8 AC DJ C 0CW4A17483000 10- 61 AL EB C
0CW4A17340000 14- 9 AG DX C 0CW4A17485000 12- 75 AK DX C
0CW4A17341000 11- 52 AH DX C 0CW4A17486000 10- 51 AM EG C
0CW4A17344000 11- 51 AE DJ C 0CW4A17487000 10- 55 AF DS C
0CW4A17345000 11- 47 AE DJ C 0CW4A17488000 4- 28 AV FG D
0CW4A17346000 11- 19 AC DJ C 0CW4A17489000 3- 63 AG DS C
0CW4A17347000 11- 20 AD DJ C 0CW4A17491000 3- 55 AW FG C
0CW4A17348000 11- 21 AD DJ C 0CW4A17492000 14- 76 AF DS C
0CW4A17349000 4- 11 AF DS C 0CW4A17495000 4- 25 AD DJ C
0CW4A17350000 13- 10 AC DJ C 0CW4A17496000 4- 26 AD DJ C
0CW4A17351000 11- 22 AD DJ C 0CW4A17504000 12- 74 AF DS C
0CW4A17352000 11- 39 AC DJ C 0CW4A17505000 4- 19 AD DJ C
0CW4A17353010 3- 6 AE DJ C 0CW4A17506000 4- 20 AE DS C
0CW4A17354000 3- 7 AE DJ C 0CW4A17507000 4- 21 AD DJ C
0CW4A17355000 3- 37 AD DJ C 0CW4A17508000 4- 22 AG DX C
0CW4A17357000 12- 11 AD DJ C 0CW4A17510000 3- 58 AK DX C
0CW4A17358000 14- 12 AP EQ C 0CW4A17511000 3- 56 AR EQ C
0CW4A17359000 14- 13 AK DX C 0CW4A17512000 3- 61 AE DJ C
0CW4A17360000 14- 14 AK DX C 0CW4A17513000 11- 41 AD DJ C
0CW4A17361000 13- 15 AD DJ C 0CW4A17514000 10- 33 AE DS C

– 42 –
PRICE R. PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R PARTS CODE NO. Ex. Ja.
NEW P/R

0CW4A17515000 4- 9 AC DJ C 0CW4A18327000 13- 55 AL EB C


0CW4A17516000 8- 25 AK DX C 0CW4A18328000 13- 83 AC DJ C
0CW4A17517000 3- 14 AE DS C 0CW4A18329000 13- 37 AC DJ C
0CW4A17519000 10- 16 AR EQ D 0CW4A18330000 12- 38 AD DJ C
0CW4A17523000 3- 17 AC DJ C 0CW4A18331000 13- 39 AD DJ C
0CW4A17524000 3- 18 AD DJ C 0CW4A18332000 12- 40 AR EQ C
0CW4A17525000 12- 72 AD DJ C 0CW4A18334000 10- 22 AC DJ C
0CW4A17526000 9- 15 AF DS C 0CW4A18338010 2- 39 AH DX C
0CW4A17528000 3- 19 AC DJ C 0CW4A18672000 5- 9 AY FQ C
0CW4A17530000 14- 29 AD DJ C 0CW4A18673000 5- 10 AF DS D
0CW4A17531000 11- 37 AK DX C 0CW4A18679000 5- 13 AF DS C
0CW4A17533000 12- 30 AC DJ C 0CW4A18680000 5- 14 AF DS C
" 13- 30 AC DJ C 0CW4A18681000 5- 15 AM EG C
0CW4A17536000 14- 51 AC DJ C 0CW4A18682000 6- 5 AG DX D
0CW4A17539000 3- 32 AK DX C 0CW4A18683000 5- 5 AE DJ C
0CW4A17540000 3- 33 AC DJ C 0CW4A18684000 5- 55 AF DS C
0CW4A17542000 3- 20 AC DJ C 0CW4A18685000 5- 2 AF DS C
0CW4A17543000 3- 62 AE DS C 0CW4A18686000 5- 17 AT EZ D
0CW4A17544000 14- 52 AR EQ C 0CW4A18688000 6- 1 AD DJ C
0CW4A17545000 14- 53 AQ EQ C 0CW4A18689000 5- 56 AF DS C
0CW4A17549000 3- 34 AC DJ C 0CW4A18690000 6- 21 AH DX C
0CW4A17551000 13- 31 AD DJ C 0CW4A18704000 5- 21 AN EQ D
0CW4A17552000 12- 32 AF DS C 0CW4A18708000 5- 22 AY FQ C
0CW4A17566000 12- 33 AD DJ C 0CW4A18857000 2- 1 AG DX C
" 13- 33 AD DJ C 0CW4A18863000 4- 44 AE DJ C
" 8- 9 AD DJ C 0CW4A18869000 4- 43 AE DS C
0CW4A17567000 10- 19 AD DJ C 0CW4A18877000 10- 37 AF DS D
" 13- 34 AD DJ C 0CW4A18881000 15- 55 AF DS C
" 14- 34 AD DJ C 0CW4A18884000 16- 34 BF GN E
" 3- 21 AD DJ C 0CW4A18888000 11- 69 AN EG C
" 8- 10 AD DJ C 0CW4A18889010 10- 13 AD DJ C
0CW4A17572000 10- 20 AE DJ C 0CW4A18904000 15- 13 AF DS C
" 3- 22 AE DJ C 0CW4A18905000 15- 17 AH DX C
" 8- 11 AE DJ C 0CW4A18907000 15- 23 AH DX D
0CW4A17573000 12- 36 AE DS C 0CW4A18910000 1- 34 AH DX C
" 13- 36 AE DS C 0CW4A18919000 1- 6 AN EG C
" 8- 12 AE DS C 0CW4A18920000 1- 11 AH DX C
0CW4A17575010 10- 43 AE DS D 0CW4A18921000 1- 25 AH DX C
0CW4A17576000 3- 53 AH DX C 0CW4A18923000 1- 37 AM EG C
0CW4A17577000 3- 2 AE DS C 0CW4A18924010 10- 28 AD DJ C
0CW4A17578000 3- 49 AD DJ C 0CW4A18926000 1- 26 AK EB C
0CW4A17581000 15- 28 AF DS C 0CW4A18927000 1- 27 AK EB C
0CW4A17583000 15- 31 AD DJ C 0CW4A18928000 1- 1 BD GN C
0CW4A17584000 15- 29 AD DJ C 0CW4A18934000 1- 30 AR EQ C
0CW4A17585000 11- 42 AE DJ C 0CW4A18935000 1- 43 AF DS C
0CW4A17589000 16- 9 AD DJ C 0CW4A18936000 1- 31 AX FG C
0CW4A17590000 15- 51 AC DJ C 0CW4A18937000 1- 33 AN EQ C
0CW4A17591000 16- 8 AF DS C 0CW4A18938000 1- 32 AH DX C
0CW4A17592000 15- 10 AE DJ C 0CW4A18939000 1- 35 AF DS C
0CW4A17691000 3- 23 AC DJ C 0CW4A18948000 4- 42 AN EG C
0CW4A18198000 15- 36 AC DJ C 0CW4A18951000 4- 41 AG DX C
0CW4A18206000 15- 1 AD DJ C 0CW4B10082000 10- 68 AF DS C
0CW4A18207000 15- 2 AN EQ C 0CW4B10085000 10- 65 AK EB C
0CW4A18210000 15- 35 AD DJ C 0CW4B10086000 10- 63 AL EB C
0CW4A18211000 15- 56 AD DJ C 0CW4B10087000 10- 67 AK EB C
0CW4A18214000 15- 3 AG DX D 0CW4B10111000 11- 68 AE DS C
0CW4A18215000 16- 4 AF DS C 0CW4B10138010 10- 23 AU EZ C
0CW4A18217000 15- 5 AE DS C 0CW4B10140000 11- 65 AN EQ C
0CW4A18218000 16- 6 AF DS C 0CW4B10144000 10- 64 AE DJ C
0CW4A18219000 16- 7 AF DS C 0CW4B10149000 11- 66 AD DJ C
0CW4A18225000 15- 11 AD DJ C 0CW4B10156000 10- 66 AE DJ C
0CW4A18226000 16- 12 AE DJ C 0CW4B10389000 1- 9 AU EZ C
0CW4A18227000 15- 57 AP EQ B 0CW4B10390000 3- 51 AN EQ C
0CW4A18229000 16- 14 AF DS C 0CW4B10391000 1- 20 AD DJ C
0CW4A18230000 16- 15 AE DJ C 0CW4B10394000 2- 53 AL EB C
0CW4A18232000 15- 48 AF DS C 0CW4B10395000 2- 52 AL EB C
0CW4A18238000 15- 22 AR EQ D 0CW4B10476000 6- 10 AG DS D
0CW4A18240000 15- 26 AQ EQ C 0CW4B10477000 6- 12 AG DS C
0CW4A18263000 16- 30 AE DS D 0CW4B10485000 18- 12 AF DS D
0CW4A18264000 16- 25 AE DS D 0CW4B10486000 18- 13 AF DS D
0CW4A18265000 16- 24 AE DS D 0CW4B10488000 18- 11 AF DS D
0CW4A18313000 2- 24 AE DJ C 0CW4B10489000 18- 10 AF DS D
0CW4A18314000 4- 29 AC DJ C " 5- 8 AF DS D
0CW4A18316000 4- 8 AD DJ D 0CW4B10490000 6- 20 AG DX C
0CW4A18319000 10- 21 AD DJ C 0CW4B10493000 5- 25 AE DS C
0CW4A18320000 11- 61 AC DJ C 0CW4B10494000 5- 53 AS EQ C
0CW4A18322000 14- 70 AC DJ C 0CW4B10495000 5- 18 AQ EQ D
0CW4A18323000 12- 80 AC DJ C 0CW4B10584000 2- 43 AD DJ C
0CW4A18324000 13- 58 AE DS C 0CW4B10585000 2- 25 AD DJ C
0CW4A18325000 13- 79 AN EG C 0CW4B10586010 4- 4 AC DJ C
0CW4A18326000 13- 56 AK DX C 0CW4B10591000 11- 56 AF DS C

– 43 –
PRICE R. PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R PARTS CODE NO. Ex. Ja.
NEW P/R

0CW4B10740000 15- 53 AE DS C 0CW61637///// 17- 16 AA DJ N D


0CW4B10742000 15- 50 AF DS C 0CW616371//// 18- 8 AA DJ D
0CW4B10743000 15- 27 AE DJ C " 25- 9 AA DJ D
0CW4B10744000 15- 44 AE DJ C 0CWCLP00010// 1- 55 AD DJ N C
0CW4B10746000 15- 47 AD DJ C 0CWE312001475 19- 2 AF DS B
0CW4B10754000 15- 43 AE DJ C 0CWE314000784 23- 15 AP EQ N B
0CW4B10776000 10- 49 AF DS C " 24- 32 AP EQ N B
0CW4B10778000 10- 46 AF DS C 0CWE321000945 19- 3 AT EZ N B
0CW4B10779000 10- 45 AF DS C 0CWE323000483 19- 5 AH DX N B
0CW4B10780000 2- 13 AF DS C 0CWE323000494 19- 4 AH DX N B
0CW4B10783000 9- 19 AG DX C 0CWE450000384 22- 15 AB DD C
0CW4B10785000 3- 50 AC DJ C " 24- 53 AB DD C
0CW4B10845000 2- 51 AD DJ C 0CWE450001128 23- 40 AC DJ C
0CW4B10846000 11- 53 AD DJ C " 24- 44 AC DJ C
0CW4B10847000 5- 23 AF DS D 0CWE450001139 24- 35 AC DJ C
0CW4B10848000 2- 504 AB DJ C 0CWE450001148 23- 39 AE DS N C
0CW4B10851000 2- 50 AD DX C 0CWE450001297 24- 45 AH DX N C
0CW4B10852000 10- 57 AE DS C 0CWE73543M476 19- 6 AD DJ C
0CW4F11556000 3- 27 AG DX C 0CWE74561WE03 24- 54 AE DS N C
0CW4F11557000 4- 15 AH DX C 0CWE74566WE03 19- 7 AD DJ N C
0CW4F11558000 3- 65 AH DX C 0CWE74566WE04 19- 8 AD DJ N C
0CW4F11560000 3- 60 AH DX C 0CWE75317BK22 24- 38 BB GD N C
0CW4F11562000 7- 15 AT EZ C 0CWE7709532// 19- 9 AF DS N B
0CW4F11563010 8- 27 BA FX C 0CWER040SKP// 21- 13 AB DD C
0CW4F11564000 10- 53 AW FG C " 22- 8 AB DD C
0CW4F11565000 11- 59 AP EQ C " 23- 13 AB DD C
0CW4F11566000 9- 22 AG DX C 0CWER050SKP// 23- 20 AA DD C
0CW4F11568010 12- 78 AY FQ C " 24- 29 AA DD C
0CW4F11569000 13- 75 AK DX C 0CWER060SKN// 2- 66 AA DJ N C
0CW4F11570000 13- 76 AK DX C 0CWFB55968000 6- 11 AH DX C
0CW4F11679000 15- 32 AF DS C 0CWFB55969000 6- 22 AE DJ C
0CW4F11850000 5- 52 AU EZ C 0CWFB56775000 6- 9 AH DX C
0CW4F11882000 3- 47 AT EZ C 0CWFC15034000 15- 19 AC DJ C
0CW4F11883000 3- 52 AN EQ C 0CWFC21175000 14- 35 AC DJ C
0CW4F12053000 15- 46 AH DX C 0CWFC22120000 10- 3 AC DJ C
0CW4G11297020 5- 1 CA TR E " 11- 8 AC DJ C
0CW4H16449010 10- 44 AM EG B " 12- 44 AC DJ C
" 4- 17 AM EG B " 13- 44 AC DJ C
0CW4H16450000 14- 45 AT EZ E " 1- 39 AC DJ C
0CW4H16452000 4- 30 AQ EQ C " 14- 44 AC DJ C
0CW4H16453000 4- 31 AU EZ C " 2- 28 AC DJ C
0CW4H16454000 10- 2 AE DS C " 3- 4 AC DJ C
" 4- 13 AE DS C " 4- 3 AC DJ C
" 9- 1 AE DS C " 5- 7 AC DJ C
0CW4H16455000 10- 10 AK EB C " 7- 7 AC DJ C
0CW4H16456000 14- 41 AN EG C " 8- 13 AC DJ C
0CW4H16458000 7- 5 AK DX C " 9- 2 AC DJ C
0CW4H16460000 3- 41 AP EQ C 0CWFC25031000 8- 17 AC DJ C
0CW4H16461000 4- 32 AN EQ C 0CWFC25034000 10- 12 AB DJ C
0CW4H16462000 4- 33 AL EB C " 3- 36 AB DJ C
0CW4H16464000 10- 26 AN EQ C " 7- 8 AB DJ C
0CW4H16465000 4- 35 AQ EQ C 0CWFC25035000 16- 20 AC DJ C
0CW4H16467000 3- 43 AP EQ C 0CWFC25827000 10- 29 AE DJ C
0CW4H16468000 8- 22 AY FQ C " 11- 9 AE DJ C
0CW4H16504000 16- 39 AK DX C " 12- 46 AE DJ C
0CW4H16505000 16- 40 AH DX C " 13- 46 AE DJ C
0CW4H16506000 15- 41 AW FG C " 14- 46 AE DJ C
0CW4H16512000 3- 16 AF DS C " 2- 6 AE DJ C
0CW4H16514000 5- 3 AP EQ C " 3- 28 AE DJ C
0CW4H16515000 5- 4 AH DX C " 4- 5 AE DJ C
0CW4H16523000 6- 2 BA FX C " 7- 9 AE DJ C
0CW4H16524000 5- 6 AV FG C " 9- 6 AE DJ C
0CW4H16530000 5- 20 AG DX C 0CWFC30661000 1- 36 AC DJ C
0CW4H16531000 6- 15 AP EQ C " 15- 18 AC DJ C
0CW4H16553000 4- 36 AS EQ C 0CWFC30779000 1- 41 AC DJ C
0CW4H16602000 3- 42 AU EZ C " 15- 33 AC DJ C
0CW4K11066000 10- 34 BE GN B 0CWFF60507000 6- 7 AV FG C
0CW4K11067000 10- 11 BA FX B 0CWFF60508000 6- 8 AV FG C
0CW4K11069000 8- 19 BR LX B 0CWFS19009000 3- 5 AC DJ C
0CW4K11070000 15- 42 BE GN B 0CWFS19102000 6- 3 AC DJ C
0CW4K11078000 5- 19 BB FX B 0CWFS21615000 14- 47 AS EZ C
0CW4K11080000 3- 35 BF GN B " 8- 14 AS EZ C
0CW4K14040000 12- 42 BB GD B 0CWFS21672000 10- 30 AD DJ C
0CW4S10280000 15- 45 AD DS C " 11- 27 AD DJ C
0CW4S12048000 2- 18 AL EB C " 12- 48 AD DJ C
0CW4S12049000 2- 19 AL EB C " 14- 48 AD DJ C
0CW4S19048000 13- 43 AC DJ C " 4- 6 AD DJ C
0CW4S19049000 8- 23 AD DJ C " 7- 10 AD DJ C
0CW4S19076000 15- 21 AC DJ C 0CWFS26593000 1- 29 AD DJ C
0CW4S19077000 3- 26 AC DJ C 0CWFS56528000 6- 4 AE DJ C
" 4- 2 AC DJ C 0CWHW030FNS// 21- 16 AC DJ N C

– 44 –
PRICE R. PRICE R.
PARTS CODE NO. Ex. Ja.
NEW P/R PARTS CODE NO. Ex. Ja.
NEW P/R

0CWHW030FNS// 22- 26 AC DJ N C 0CWXD32200142 3- 501 AC DJ C


0CWHW050FZS00 13- 82 AB DJ C " 7- 502 AC DJ C
0CWHW080FWS// 1- 54 AC DJ N C " 8- 501 AC DJ C
0CWNSBLT00333 23- 25 AS EQ N B 0CWXD32300122 16- 506 AC DJ C
0CWNSBLT00338 23- 19 AS EQ N B 0CWXD32300142 14- 504 AD DJ C
0CWNSBLT00339 23- 23 AR EQ N B " 15- 507 AD DJ C
0CWNSBRG00110 22- 7 AU EZ N C 0CWXD32300162 12- 505 AC DJ C
" 23- 12 AU EZ N C 0CWXD32300182 14- 506 AC DJ C
0CWNSBSH00002 21- 11 AH DX N C " 8- 502 AC DJ C
" 24- 13 AH DX N C 0CWXF21309000 16- 16 AS EZ B
0CWNSCLP00005 20- 10 AE DJ N C " 16- 42 AS EZ B
" 22- 24 AE DJ N C 0CWXF21604940 11- 29 AL EB B
" 24- 12 AE DJ N C 0CWXF21605040 3- 46 AL EB B
0CWNSCLP00008 20- 8 AE DJ N C 0CWXF21606140 10- 4 AL EB B
" 24- 11 AE DJ N C 0CWXF21607240 14- 49 AN EG B
0CWNSSCR00017 22- 12 AD DJ N C 0CWXF21607440 4- 18 AK DX B
" 23- 16 AD DJ N C 0CWXF21607640 11- 30 AN EG B
" 24- 21 AD DJ N C 0CWXF21608040 7- 12 AN EG B
0CWNSSCR00087 23- 8 AE DS N C 0CWXF21618840 3- 40 AP EQ B
0CWNSSCR00225 24- 36 AC DJ N C 0CWXF21619860 3- 39 AQ EQ B
0CWNSSCR00226 22- 2 AE DJ N C 0CWXF21804070 15- 49 AQ EQ B
0CWPW060025// 23- 37 AA DJ C 0CWXF21807000 8- 15 AP EQ B
0CWPW060050// 12- 82 AA DD C 0CWXF21817960 3- 38 AS EZ B
0CWRA22452000 15- 52 AC DJ C
0CWSCR00045// 17- 22 AC DJ C
0CWVT20002018 4- 50 AE DJ C
0CWVT25019030 4- 49 AE DS C
0CWVT25171030 4- 51 AE DS C
0CWWA70484000 5- 51 AN EG B
0CWWG85362000 10- 14 AH DX B
" 11- 28 AH DX B
" 12- 54 AH DX B
" 3- 25 AH DX B
" 4- 7 AH DX B
" 5- 16 AH DX B
" 6- 6 AH DX B
" 7- 11 AH DX B
" 9- 16 AH DX B
0CWWG85421000 8- 20 AR EQ B
0CWWT25035000 23- 36 AD DJ C
0CWXB12300605 15- 502 AB DJ C
" 6- 501 AB DJ C
0CWXB12300805 6- 507 AB DJ C
0CWXB12400605 5- 501 AB DJ C
0CWXB12400606 10- 504 AB DJ C
0CWXB12400607 15- 505 AB DJ C
0CWXB12400805 6- 508 AB DJ C
0CWXB12401005 13- 501 AB DJ C
0CWXB24300605 5- 504 AB DJ C
0CWXB24300805 6- 505 AB DJ C
0CWXB47300607 2- 503 AB DJ C
0CWXB47300805 5- 502 AB DJ C
" 6- 502 AB DJ C
0CWXB47301209 6- 504 AB DJ C
0CWXB47401006 2- 81 AB DJ C
0CWXB47401007 10- 501 AB DJ C
" 11- 502 AB DJ C
" 15- 503 AB DJ C
" 2- 502 AB DJ C
" 3- 502 AB DJ C
" 4- 501 AB DJ C
0CWXD11104629 5- 503 AC DJ C
0CWXD12300142 3- 503 AC DJ C
0CWXD21100402 13- 81 AC DJ C
0CWXD21100502 12- 83 AC DJ C
" 15- 501 AC DJ C
" 16- 501 AC DJ C
" 6- 503 AC DJ C
0CWXD21100642 15- 504 AC DJ C
" 16- 504 AC DJ C
" 6- 506 AC DJ C
0CWXD32200102 10- 503 AC DJ C
" 11- 501 AC DJ C
" 12- 502 AC DJ C
" 14- 502 AC DJ C
0CWXD32200122 10- 502 AC DJ C
" 4- 502 AC DJ C
" 7- 501 AC DJ C
" 8- 503 AC DJ C
0CWXD32200142 13- 503 AC DJ C
" 16- 508 AC DJ C

– 45 –
Memo
Memo
Memo
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.

Example:

<Solder composition code of lead-free solder>

Solder composition Solder composition Solder composition code


code (Refer to the Sn-Ag-Cu a
Lead-Free table at the right.)
Sn-Ag-Bi
b
Sn-Ag-Bi-Cu
Sn-Zn-Bi z
5mm
a Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
i
n
s
Bi-Sn-Ag-P p
Bi-Sn-Ag

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD


When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the
exclusive-use soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK


Since the melting point of lead-freeCOPYRIGHT © XXXX
solder is about 220°C, which BYSHARP
is about 40°C higherCORPORATION
than that of conventional lead solder, and its soldering
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature ALLofRIGHTS
components. Use enough care to separate the soldering iron from the PWB when
RESERVED.
completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron
tip after completion of soldering work. No part of this publication may be reproduced,
If the soldering iron tip is discolored black stored in a retrieval
during soldering work,system, orfile
clean and transmitted
the tip within
steel wool or a fine filer.
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
CAUTION FOR BATTERY REPLACEMENT
(Danish) ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English) Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish) VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French) ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish) VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German) Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY DISPOSAL


(For USA, CANADA)
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY
(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY
THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE
BATTERY FROM THE PRODUCT AND CONTACT YOUR
LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION
ON RECYCLING AND DISPOSAL OPTIONS.

“TRAITEMENT DES PILES USAGÉES”


CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE
MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE)
QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA
PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE
AGENCE ENVIRONNEMENTALE LOCALE POUR DES
INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET
DE TRAITEMENT.
COPYRIGHT © 2005 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.

Trademark acknowledgements
Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
Windows® XP, Windows® 2000 Server, Windows® Server 2003 and Internet
Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and
other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
re
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION
Digital Document System Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186, Japan
2005 November Printed in Japan

You might also like