Safety Data Sheet

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

Texclad 2
Product Use: Industrial Grease
Product Number(s): 219570, 277116
Company Identification
Chevron Canada Limited
500 - 5th Ave. SW
Calgary, ALBERTA T2P 0L7
Canada
www.chevronlubricants.com

Transportation Emergency Response

CHEMTREC: (800) 424-9300 or (703) 527-3887
Health Emergency
Chevron Emergency & Information Center: Located in the USA. International collect calls accepted. (800) 231-
0623 or (510) 231-0623
Product Information
email : lubemsds@chevron.com
Product Information: (800) LUBE TEK

SECTION 2 HAZARDS IDENTIFICATION

CLASSIFICATION: Not classified as hazardous according to Canada regulatory guidelines.

SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

COMPONENTS CAS NUMBER AMOUNT

Highly refined mineral oil (C15 - C50) Mixture 45 - 70 %wt/wt
Note that the actual concentration or concentration range of some or all of the above ingredients is considered
confidential business information and is being withheld as permitted by WHMIS 2015.

_____________________________________________________________________
Revision Number: 4 1 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
 SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes
with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated.
To remove the material from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly
clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical
advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move
the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.

Most important symptoms and effects, both acute and delayed

IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: High-Pressure Equipment Information: Accidental high-velocity injection under the skin of materials of this
type may result in serious injury. Seek medical attention at once should an accident like this occur. The initial
wound at the injection site may not appear to be serious at first; but, if left untreated, could result in disfigurement or
amputation of the affected part.
Contact with the skin is not expected to cause prolonged or significant irritation. Contact with the skin is not
expected to cause an allergic skin response. Not expected to be harmful to internal organs if absorbed through the
skin.
Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause
respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at airborne
levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include
coughing and difficulty breathing.

Indication of any immediate medical attention and special treatment needed

Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin.
Such an accident may result in a small, sometimes bloodless, puncture wound. However, because of its driving
force, material injected into a fingertip can be deposited into the palm of the hand. Within 24 hours, there is
usually a great deal of swelling, discoloration, and intense throbbing pain. Immediate treatment at a surgical
emergency center is recommended.

SECTION 5 FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

PROTECTION OF FIRE FIGHTERS:

Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper
handling and storage. For fires involving this material, do not enter any enclosed or confined fire space without
proper protective equipment, including self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids,
liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved
when this material undergoes combustion. Combustion may form oxides of: Molybdenum, Calcium, Sulfur.

SECTION 6 ACCIDENTAL RELEASE MEASURES

_____________________________________________________________________
Revision Number: 4 2 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.
Spill Management: Clean up spills immediately, observing precautions in Exposure Controls/Personal Protection
section. Stop the source of the release if you can do it without risk. Contain release to prevent further
contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing precautions in
Exposure Controls/Personal Protection. Use appropriate techniques such as applying non-combustible absorbent
materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials
in disposable containers and dispose of in a manner consistent with applicable regulations.
Reporting: Report spills to local authorities as appropriate or required.

SECTION 7 HANDLING AND STORAGE

General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage
systems and bodies of water.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material.
To minimize this hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient.
Review all operations which have the potential of generating and accumulating an electrostatic charge and/or a
flammable atmosphere (including tank and container filling, splash filling, tank cleaning, sampling, gauging, switch
loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate mitigating procedures.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty container or it
may rupture with explosive force. Empty containers retain product residue (solid, liquid, and/or vapor) and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks,
static electricity, or other sources of ignition. They may explode and cause injury or death. Empty containers
should be completely drained, properly closed, and promptly returned to a drum reconditioner or disposed of
properly.

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 2), applicable exposure limits, job activities, and other
substances in the work place when designing engineering controls and selecting personal protective equipment. If
engineering controls or work practices are not adequate to prevent exposure to harmful levels of this material, the
personal protective equipment listed below is recommended. The user should read and understand all instructions
and limitations supplied with the equipment since protection is usually provided for a limited time or under certain
circumstances.

ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT

Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear safety
glasses with side shields as a good safety practice.
Skin Protection: No special protective clothing is normally required. Where splashing is possible, select
protective clothing depending on operations conducted, physical requirements and other substances in the
workplace. Suggested materials for protective gloves include: Neoprene, Nitrile Rubber, Viton.
Respiratory Protection: No respiratory protection is normally required.
If user operations generate an oil mist, determine if airborne concentrations are below the occupational exposure
limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection from the measured
concentrations of this material. For air-purifying respirators use a particulate cartridge.
Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not provide
adequate protection.
Occupational Exposure Limits:

_____________________________________________________________________
Revision Number: 4 3 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
Component Country/ Form TWA STEL Ceiling Notation
Agency
Highly refined mineral oil ACGIH -- 5 mg/m3 10 mg/m3 -- --
(C15 - C50)
NOTE ON OCCUPATIONAL EXPOSURE LIMITS: Consult local authorities for acceptable provincial values in
Canada. Consult the Canadian Standards Association Standard Z94.4-2011 Selection, Use and Care of Respirators.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: the data below are typical values and do not constitute a specification.

Color: Black to grey

Physical State: Semi-solid
Odor: Petroleum odor
Odor Threshold: Not available
pH: Not available
Vapor Pressure: Not available
Vapor Density (Air = 1): Not available
Initial Boiling Point: 371°C (699.8°F) (Typical)
Solubility: Negligible
Freezing Point: Not available
Melting Point: 99°C (210.2°F) (Typical)
Specific Gravity: 0.88 @ 16°C (60.8°F) (Typical)
Density: 0.94 kg/l @ 15°C (59°F) (Typical)
Viscosity: 34 mm2/s @ 100°C (212°F) (Minimum)
Coefficient of Therm. Expansion / °F: Not available
Evaporation Rate: Not available
Decomposition temperature: Not available
Octanol/Water Partition Coefficient: Not available

FLAMMABLE PROPERTIES:
Flammability (solid, gas): Not Applicable

Flashpoint: (Cleveland Open Cup) 260 °C (500 °F) (Minimum)

Autoignition: 288 °C (550 °F)
Flammability (Explosive) Limits (% by volume in air): Lower: Not Applicable Upper: Not
Applicable

SECTION 10 STABILITY AND REACTIVITY

Reactivity: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc.
Chemical Stability: This material is considered stable under normal ambient and anticipated storage and
handling conditions of temperature and pressure.
Incompatibility With Other Materials: Not applicable
Hazardous Decomposition Products: None known (None expected)
Hazardous Polymerization: Hazardous polymerization will not occur.
Sensitivity to Mechanical Impact: No.

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Serious Eye Damage/Irritation: The eye irritation hazard is based on evaluation of data for product components.
Skin Corrosion/Irritation: The skin irritation hazard is based on evaluation of data for product components.

_____________________________________________________________________
Revision Number: 4 4 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
Skin Sensitization: The skin sensitization hazard is based on evaluation of data for product components.
Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for product components.
Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for product components.
Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for product
components.For additional information on the acute toxicity of the components, call the technical information
center.
Acute Toxicity Estimate: Not Determined

Germ Cell Mutagenicity: The hazard evaluation is based on data for components or a similar material.

Carcinogenicity: The hazard evaluation is based on data for components or a similar material.

Reproductive Toxicity: The hazard evaluation is based on data for components or a similar material.

Specific Target Organ Toxicity - Single Exposure: The hazard evaluation is based on data for components or a
similar material.

Specific Target Organ Toxicity - Repeated Exposure: The hazard evaluation is based on data for components or a
similar material.

ADDITIONAL TOXICOLOGY INFORMATION:

This product contains petroleum base oils which may be refined by various processes including severe solvent
extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer warning under the
OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not been listed in the National
Toxicology Program (NTP) Annual Report nor have they been classified by the International Agency for Research
on Cancer (IARC) as; carcinogenic to humans (Group 1), probably carcinogenic to humans (Group 2A), or possibly
carcinogenic to humans (Group 2B).
These oils have not been classified by the American Conference of Governmental Industrial Hygienists (ACGIH)
as: confirmed human carcinogen (A1), suspected human carcinogen (A2), or confirmed animal carcinogen with
unknown relevance to humans (A3).

SECTION 12 ECOLOGICAL INFORMATION

ECOTOXICITY
This material is not expected to be harmful to aquatic organisms.
The product has not been tested. The statement has been derived from products of a similar structure and
composition.

MOBILITY
No data available.

PERSISTENCE AND DEGRADABILITY

This material is not expected to be readily biodegradable. The biodegradability of this material is based on an
evaluation of data for the components or a similar material.
The product has not been tested. The statement has been derived from the properties of the individual components.

POTENTIAL TO BIOACCUMULATE
Bioconcentration Factor: No data available.
Octanol/Water Partition Coefficient: No data available

SECTION 13 DISPOSAL CONSIDERATIONS

_____________________________________________________________________
Revision Number: 4 5 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil
recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with
applicable regulations. Contact your sales representative or local environmental or health authorities for approved
disposal or recycling methods. (See B.C. Reg. GY/92 Waste Management Act; R.R.O. 1990, Reg. 347 General-
Waste Management; C.C.SM.c. W40 The Waste Reduction and Prevention Act; N.S. Reg. 51/95 and N.S. Reg.
179/96 for examples of Provincial legislation.)

SECTION 14 TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods
Regulations, for additional description requirements (e.g., technical name) and mode-specific or quantity-specific
shipping requirements.

TC Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT UNDER

TRANSPORT CANADA

IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER THE IMDG CODE

ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER ICAO

DOT Shipping Description: NOT REGULATED AS HAZARDOUS MATERIAL UNDER 49 CFR

SECTION 15 REGULATORY INFORMATION

REGULATORY LISTS SEARCHED:

01-1=IARC Group 1
01-2A=IARC Group 2A
01-2B=IARC Group 2B

No components of this material were found on the regulatory lists above.

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements: AICS (Australia), DSL (Canada),
EINECS (European Union), ENCS (Japan), IECSC (China), KECI (Korea), NZIoC (New Zealand), PICCS
(Philippines), TSCA (United States).

SECTION 16 OTHER INFORMATION

REVISION STATEMENT: SECTION 01 - Company MSDS Address information was modified.

SECTION 01 - Health Emergency information was modified.
SECTION 01 - Product Code(s) information was modified.
SECTION 01 - Product Use information was modified.
SECTION 03 - Composition information was added.
SECTION 03 - Composition information was deleted.
SECTION 04 - First Aid - Skin information was modified.
SECTION 04 - Immediate Health Effects - Skin information was modified.
SECTION 05 - Fire Fighters Protection Measures information was modified.
SECTION 05 - Special hazards arising from the substance or mixture information was added.
SECTION 08 - Occupational Exposure Limit Table information was modified.
SECTION 09 - Ecological Information information was added.
SECTION 09 - Ecological Information information was deleted.
_____________________________________________________________________
Revision Number: 4 6 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160
SECTION 09 - Physical/Chemical Properties information was added.
SECTION 09 - Physical/Chemical Properties information was deleted.
SECTION 09 - Physical/Chemical Properties information was modified.
SECTION 11 - Additional Toxicology Information information was deleted.
SECTION 11 - Toxicological Information information was modified.
SECTION 14 - DOT Classification information was modified.
SECTION 14 - TC Classification information was modified.
SECTION 15 - Chemical Inventories information was deleted.
SECTION 15 - Chemical Inventories information was modified.
SECTION 15 - Regulatory Information information was deleted.

Revision Date: October 04, 2019

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:

TLV - Threshold Limit Value TWA - Time Weighted Average
STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit
GHS - Globally Harmonized System CAS - Chemical Abstract Service Number
ACGIH - American Conference of Governmental IMO/IMDG - International Maritime Dangerous
Industrial Hygienists Goods Code
API - American Petroleum Institute SDS - Safety Data Sheet
WHMIS - Workplace Hazardous Materials NFPA - National Fire Protection Association (USA)
Information System
DOT - Department of Transportation (USA) NTP - National Toxicology Program (USA)
IARC - International Agency for Research on OSHA - Occupational Safety and Health
Cancer Administration
NCEL - New Chemical Exposure Limit EPA - Environmental Protection Agency
SCBA - Self-Contained Breathing Apparatus

Prepared according to the WHMIS 2015 by Chevron Energy Technology Company, 6001 Bollinger Canyon Road,
San Ramon, CA 94583.

The above information is based on the data of which we are aware and is believed to be correct as of the date
hereof. Since this information may be applied under conditions beyond our control and with which we may
be unfamiliar and since data made available subsequent to the date hereof may suggest modifications of the
information, we do not assume any responsibility for the results of its use. This information is furnished
upon condition that the person receiving it shall make his own determination of the suitability of the
material for his particular purpose.

_____________________________________________________________________
Revision Number: 4 7 of 7 Texclad 2
Revision Date: October 04, 2019 SDS : 24160