Vdocuments - MX - Caterpillar Cat 320l Track Excavator Prefix 8lk Service Repair Manual 8lk00001 and Up 1586311769

Service Repair Manual
Model
320, 320L TRACK EXCAVATOR

w 1/2(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 8LK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 8LK00001-UP (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly

3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564587
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.
Illustration 1 g00608177
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2019/9/15
w 2/2(W)
2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil
return line (6) (not shown) as a unit.
3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft).
Note: Two nuts are installed on each turbocharger mounting stud.
4. Slide hose (7) down the oil return line (6) onto fitting (8) .
5. Tighten two clamps (5) on hose (7) .
6. Connect oil supply line (4) to the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc. Sun Sep 15 11:07:30 UTC+0800 2019
All Rights Reserved.
Private Network For SIS Licensees.
w 1/3(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01565722
Exhaust Manifold - Remove and Install

SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
w 2/3(W)
1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2. Remove exhaust manifold (2) from the cylinder head assembly.
3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the
cylinder head assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
NOTICE
1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head
assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
2. Place exhaust manifold (2) in position on the cylinder head.
3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
w 3/3(W)
4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
w 1/3(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01615211
Air Inlet Heater - Remove and Install

SMCS - 1090-010
Removal Procedure
NOTICE
1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) .
2. Disconnect air inlet hose (2) from air inlet elbow (4) .
w 2/3(W)
3. Remove four bolts (3) and washers that secure the following items to the air inlet manifold:
air inlet elbow (4), gasket (5), air inlet heater (6) and gasket (7) .
4. Remove the following items from the air inlet manifold: air inlet elbow (4), gasket (5), air
inlet heater (6) and gasket (7) .
Note: Check the condition of the gaskets that are used between the elbow and the air inlet
heater. Check the gaskets between the air inlet heater and the air inlet manifold. If the
gaskets are damaged in any way, replace the gaskets.
NOTICE
w 3/3(W)
Note: Check condition of the gaskets for the air inlet elbow and the air inlet heater. If the
gaskets are damaged, use a new part for replacement. The wire mesh gasket (7) is installed
between the air inlet manifold and the air inlet heater.
1. Place the following items in position on the air inlet manifold: gasket (7), the air inlet heater
(6), gasket (5) and the air inlet elbow (4) .
2. Install four bolts (3) that secure the following items to the air inlet manifold: gasket (7), the
air inlet heater (6), gasket (5) and the air inlet elbow (4)
Tighten bolts (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
3. Connect air inlet hose (2) to air inlet elbow (4) .
4. Tighten hose clamp (1) that secures the air inlet hose to the air inlet elbow.
w 1/2(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01575215
Inlet Manifold - Remove

SMCS - 1058-011
Removal Procedure
Start By:
A. Remove fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
B. Remove fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
C. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
NOTICE
w 2/2(W)
1. Loosen clamp (1) on hose assembly (3) .
2. Remove two bolts (2) that secure the hose assembly to the engine.
3. Slide the hose assembly (3) from the retaining ring (4) .
4. Remove the bolts and washers (5) that secure the air inlet manifold to the cylinder heads.
The 3066 Engine has eleven bolts and washers while the 3064 Engine has eight bolts and
washers.
Note: One bolt has previously been removed in order to remove the fuel return line.
5. Remove one bolt (6) and the washer that secures the lifting bracket (7) to the cylinder block.
6. Remove inlet manifold (8) and remove the lifting bracket (7) .
7. Remove gaskets (9) (not shown). Check the gaskets for wear or damage. Replace the
gaskets, if the gasket is worn or damaged.
Note: The 3064 Engine has one gasket, while the 3066 Engine has two gaskets.
w 1/2(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01575229
Inlet Manifold - Install

SMCS - 1058-012
NOTICE
Note: Check condition of the inlet manifold gasket. If the gasket is damaged, use a new part
for replacement.
w 2/2(W)
1. Place the following items in position on the engine: gasket (9) (not shown), air inlet
manifold (8) and lifting bracket (7) .
2. Install the washer and one bolt (6) onto lifting bracket (7) .
3. Install the washers and bolts (5) that secure the inlet manifold to the cylinder head. The
3066 Engine has eleven washers and bolts while the 3064 Engine has eight washers and
bolts.
4. Slide the hose assembly (3) through the retaining ring (4) .
5. Install washers and two bolts (2) that secure the hose assembly to the engine.
6. Tighten the hose clamps (1) on the hose assembly (3) .
End By:
a. Install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater - Remove
and Install".
b. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
c. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
w 1/5(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01615235
Inlet and Exhaust Valve Springs - Remove and Install

SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1322 Valve Keeper Installer 1
B 9U-6145 Air Connector (1) 1
9U-6144 Adapter 1
7F-4292 Valve Spring Compressor 1
C 6V-5223 Bolt 1
8T-4121 Washer 1
6V-5218 Bolt 1
D 8S-2263 Spring Tester 1
(1)
The 9U-6145 Air Connector is part of the 9U-6274 Compression Test Kit. The 9U-6145 Air Connector can be
ordered separately.
Start By:
A. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
B. Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Remove".
w 2/5(W)
NOTICE
Care must be taken to ensure that fluids are contained during

performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Note: The following procedure is for the removal of the inlet valve springs and the exhaust valve
springs without removing the cylinder head.
1. Install Tool (B). Attach an air hose to Tool (B) in order to force air pressure into the
cylinder. This will hold the valves in position while the inlet and exhaust valve springs are
removed and installed.
Note: Maintain air pressure in each cylinder until both of the valve springs are removed and
installed.
2. Use Tool (C) to compress the valve spring (1) .
w 3/5(W)
Note: Compress the valve spring evenly in order to avoid damage to the valve stem.
3. Use the magnetic end of Tool (A) to remove cap (2) (not shown) and valve keepers (3) (not
shown) from the inlet and exhaust valves.
4. Slowly release the tension on Tool (C) .
5. Remove the retainer and spring (1) from the cylinder head assembly.
Note: Repeat Steps 1 through 5 in order to remove the remaining valve spring of the same
cylinder.
6. Check the valve spring force with Tool (D). Refer to Specifications, "Valve Mechanism" for
information on the valve springs.
7. Install the valve springs. Refer to the following installation procedure.
8. Perform Steps 1 through 7 for the removal and installation of the remaining inlet and
exhaust valve springs.
Table 2
Required Tools
A 5S-1322 Valve Keeper Installer 1
B 9U-6145 Air Connector 1
C 9U-6144 Adapter 1
7F-4292 Valve Spring Compressor 1
6V-5223 Bolt 1
8T-4121 Washer 1
w 4/5(W)
6V-5218 Bolt 1
NOTICE
1. Keep an air hose connected to Tool (B) in order to force air pressure into the cylinder. This
will hold the valves in position while the inlet and exhaust valve springs are removed and
installed.
2. Position valve spring (1) and the retainer over the valve stem.
3. Use Tool (C) to compress valve spring (1) .
Note: Compress the valve spring evenly in order to avoid damage to the valve stem.
4. Place the valve keepers (3) (not shown) in position on the inlet and exhaust valves.
Note: Tool (A) may be used to install valve keepers.
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
w 5/5(W)
5. Install cap (2) (not shown) on the inlet and exhaust valves and slowly release the tension on
Tool (C). Tap the top of valve with a soft faced hammer in order to ensure that the valve
keepers are properly installed.
Note: Repeat Steps 1 through 5 in order to install the remaining valve spring of the same
cylinder.
6. Remove air hose and Tool (B) .
7. Perform Steps 1 through 6 for the installation of the remaining inlet and exhaust valve
springs.
End By:
a. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
b. Install the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Install".
w 1/5(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01615246
Inlet and Exhaust Valves - Remove and Install

SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
A 8S-6691 Cylinder Head Repair Stand 1
B 1P-3527 Valve Spring Compressor 1
C 5S-1322 Valve Keeper Installer 1
D 8S-2263 Spring Tester 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
w 2/5(W)
1. Support cylinder head assembly (1) on Tool (A) .
2. Use tool (B) to compress valve spring (2) .
3. Use the magnetic end of tool (C) (not shown) to remove cap (4) and valve keepers (3).
Slowly release the pressure on tool (B) and remove tool (B) .
4. Remove retainer (5) and remove spring (2) .
w 3/5(W)
5. Check the valve spring force with Tool (D). Refer to Specifications, "Valve Mechanism" for
information on the valve springs.
6. Remove exhaust valve (6) and inlet valve (7) through the bottom of the cylinder head
assembly (1). Put identification marks on the valves for installation purposes.
7. Perform the following procedure, if the valves need to be refaced:
a. Set the machine that will reface the valves at an angle of 30 degrees.
b. The valve has a stellite facing. This facing will be gone, if the margin of the valve
exceeds the service limit.
c. Replace the valve, if the margin exceeds the service limit after refacing.
d. Grind the valve seat in order to reface the valve seat, if necessary.
e. Replace the valve seat, if the width exceeds the repair limit as a result of wear or
grinding.
8. Perform Steps 2 through 7 for the remaining inlet valves and exhaust valves in the cylinder
head assembly.
Table 2
Required Tools
A 8S-6691 Cylinder Head Repair Stand 1
B 1P-3527 Valve Spring Compressor 1
C 5S-1322 Valve Keeper Installer 1
NOTICE
w 4/5(W)
1. Support cylinder head assembly on Tool (A). Lubricate the inlet and exhaust valves with
clean engine oil. Install the inlet and exhaust valves through the bottom of the cylinder head.
Note: Ensure that the inlet and exhaust valves are installed in the original location in the
cylinder head.
2. Install spring (2) and retainer (5) .
3. Use Tool (B) to compress spring (2). Install valve keepers (3) and cap (4) on the valve stem
with Tool (C) .
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
w 5/5(W)
4. Carefully remove Tool (B). Tap the top of exhaust valve (6) or inlet valve (7) with a soft
faced hammer in order to ensure that the valve keepers are properly installed.
5. Repeat Steps 2 through 4 for the installation of the remaining inlet and exhaust valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
w 1/4(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01650677
Inlet and Exhaust Valve Guides - Remove and Install

SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
A 4C-6366 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
w 2/4(W)
1. Use Tool (A) to remove the inlet and exhaust valve guides (2) from the cylinder head (1) .
2. Repeat Step 1 in order to remove the remaining inlet and exhaust valve guides.
Table 2
Required Tools
A 4C-6366 Valve Guide Driver 1
B 4C-6370 Valve Guide Collar 1
NOTICE
w 3/4(W)
1. Put clean engine oil on the outside diameter of the valve guide. Install valve guide (2) with
Tool (A) and Tool (B). The valve guide is driven from the top of the cylinder head.
Typical Example
2. The counterbore in Tool (B) installs the valve guide to the correct height. Height (X) from
the top of the valve guide to the cylinder head must be 17.00 ± 0.30 mm (0.699 ± 0.012
inch). For more information on the inlet and exhaust valve guides, refer to Specifications,
"Valve Mechanism".
Note: In order to help prevent damage to the valve guides, Tool (B) must be used during
installation.
w 4/4(W)
View (X) shows that the contact between the valve and the valve seat is good. View (Y) shows that the
contact between the valve and the valve seat is poor.
3. Perform the following procedure after the valve guide has been inspected or the valve guide
has been replaced:
a. Check the valve face.
b. Press the valve that is coated with red lead against the seat without rotating the valve.
c. After refacing or replacement of the valve or valve seat, be sure to lap the valve into
the valve seat.
4. Repeat Steps 1 through 3 for the remaining inlet and exhaust valve guides.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
w 1/4(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i01565864
Inlet and Exhaust Valve Seat Inserts - Remove and Install

SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
166-7441 Valve Seat Extractor Tool Group 1
A 6V-4194 Valve Seat Extractor (1) 1
6V-4196 Valve Seat Extractor (1) 1
(1)
This is a component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
NOTICE
w 2/4(W)
A 3066 cylinder head is shown.
1. Use the valve seat grinder of Tool (A) in order to notch the valve seat.
A 3066 cylinder head is shown.
2. Use the valve seat extractor of Tool (A) to remove the inlet and exhaust valve seats.
3. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
4. Repeat Steps 1 through 3 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Table 2
Required Tools

Vdocuments - MX - Caterpillar Cat 320l Track Excavator Prefix 8lk Service Repair Manual 8lk00001 and Up 1586311769

Uploaded by

Copyright:

Available Formats

Vdocuments - MX - Caterpillar Cat 320l Track Excavator Prefix 8lk Service Repair Manual 8lk00001 and Up 1586311769

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vdocuments - MX - Caterpillar Cat 320l Track Excavator Prefix 8lk Service Repair Manual 8lk00001 and Up 1586311769

Uploaded by

Copyright:

Available Formats

Service Repair Manual

320, 320L TRACK EXCAVATOR

Disassembly and Assembly

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.

Note: Two nuts are installed on each turbocharger mounting stud.

5. Tighten two clamps (5) on hose (7) .

6. Connect oil supply line (4) to the cylinder block.

Disassembly and Assembly

Exhaust Manifold - Remove and Install

A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

2. Remove exhaust manifold (2) from the cylinder head assembly.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

2. Place exhaust manifold (2) in position on the cylinder head.

4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).

Disassembly and Assembly

Air Inlet Heater - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Tighten bolts (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

3. Connect air inlet hose (2) to air inlet elbow (4) .

Disassembly and Assembly

Inlet Manifold - Remove

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Loosen clamp (1) on hose assembly (3) .

Disassembly and Assembly

Inlet Manifold - Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

6. Tighten the hose clamps (1) on the hose assembly (3) .

Disassembly and Assembly

Inlet and Exhaust Valve Springs - Remove and Install

Care must be taken to ensure that fluids are contained during

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Dispose of all fluids according to local regulations and mandates.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

2. Use Tool (C) to compress the valve spring (1) .

4. Slowly release the tension on Tool (C) .

7. Install the valve springs. Refer to the following installation procedure.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

3. Use Tool (C) to compress valve spring (1) .

Note: Tool (A) may be used to install valve keepers.

6. Remove air hose and Tool (B) .

Disassembly and Assembly

Inlet and Exhaust Valves - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Support cylinder head assembly (1) on Tool (A) .

2. Use tool (B) to compress valve spring (2) .

4. Remove retainer (5) and remove spring (2) .