Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual Instant Download

Service Repair Manual
Models
314D LCR Excavator

314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB... 1/4
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly

C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02766796
Inlet Manifold - Remove and Install

SMCS - 1058-010
Removal Procedure
Start By:
A. Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Remove".
B. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/5/24
Illustration 1 g01375420
1. Remove bolts (1) and remove clip (2) .
2. Remove bolt (4) and remove the washers. Discard the washers.
3. Remove bolts (6) and remove the washers. Discard the washers.
4. Remove bolts (3) and remove manifold (5) .
5. Remove clips (7) .
6. Disconnect harness assemblies (8) .
7. Remove bolts (10) and remove inlet manifold (9) and the gasket.
Installation Procedure
https://www.ebooklibonline.com
Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.
NOTICE
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
1. Position the new inlet manifold gasket. Position inlet manifold (9) and install bolts (10).
Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2. Connect harness assemblies (8) and install clips (7) .
3. Position manifold (5) and install bolts (3) .
4. Install new washers and install bolt (4). Tighten bolt (4) to a torque of 34 ± 4 N·m (25 ± 3 lb
ft).
5. Install new washers and install bolts (6). Tighten bolts (6) to a torque of 34 ± 4 N·m (25 ± 3
lb ft).
6. Install clip (2) and install bolts (1) .
End By:
a. Install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater - Remove
and Install"
b. Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Install".
Copyright 1993 - 2020 Caterpillar Inc. Sun May 24 09:10:10 UTC+0800 2020
All Rights Reserved.
Private Network For SIS Licensees.
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02767700
Inlet and Exhaust Valve Springs - Remove and Install

SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
B. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Personal injury can result from being struck by parts propelled by a

released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to

release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the

valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2) .
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
Remove valve keepers (2) .
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4) .
8. If necessary, remove valve stem seals (5) .
9. Remove Tooling (A) .
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4) .
Table 2
Required Tools
A 9U-6195 Valve Spring Compressor 1
NOTICE
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure

and wear protective equipment.
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4) .
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4) .
4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5) .
5. Carefully release the pressure on Tooling (A) .
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02767800
Inlet and Exhaust Valves - Remove and Install

SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Typical Example
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Personal injury can result from being struck by parts propelled by a

released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to

release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the

valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
6. Slowly release the pressure on Tooling (B) .
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
8. Use Tooling (C) in order to remove valve stem seal (6) .
9. Repeat Steps 4 through 7 for the remaining valves.
Table 2
Required Tools
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
injury.

2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head. Check the depth of valve (2) below the face of the cylinder
head. Refer to Testing and Adjusting, "Valve Depth - Inspect" for more information.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5) .
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5) .
injury.

6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6) .
7. Carefully release the pressure on Tooling (B) .
8. Repeat Steps 2 through 7 for the remaining valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i04625005
Inlet and Exhaust Valve Guides - Remove and Install

SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during

performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool

Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Typical Example
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Table 2
Required Tools
E 384-8862 Valve Guide Installer 1
NOTICE
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02768108
Engine Oil Cooler - Remove

SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
NOTICE

performance of inspection, maintenance, testing, adjusting and repair
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service

Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
2. Remove bolts (1) .
3. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02746254
Engine Oil Cooler - Disassemble

SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
NOTICE

performance of inspection, maintenance, testing, adjusting, and repair
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool

Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02746255
Engine Oil Cooler - Assemble

SMCS - 1378-016
Assembly Procedure
NOTICE
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Shutdown SIS
Previous Screen
Product: EXCAVATOR

i02768201
Engine Oil Cooler - Install

SMCS - 1378-012
NOTICE
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.

Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual Instant Download

Uploaded by

Copyright:

Available Formats

Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual Instant Download

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual Instant Download

Uploaded by

Copyright:

Available Formats

Service Repair Manual

314D LCR Excavator

Disassembly and Assembly

Inlet Manifold - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Remove bolts (1) and remove clip (2) .

4. Remove bolts (3) and remove manifold (5) .

5. Remove clips (7) .

6. Disconnect harness assemblies (8) .

Hello dear friend!

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

2. Connect harness assemblies (8) and install clips (7) .

3. Position manifold (5) and install bolts (3) .

6. Install clip (2) and install bolts (1) .

Disassembly and Assembly

Inlet and Exhaust Valve Springs - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Personal injury can result from being struck by parts propelled by a

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to

Ensure that the valve spring is compressed squarely or damage to the

Remove valve keepers (2) .

6. Slowly release the pressure on Tooling (A).

8. If necessary, remove valve stem seals (5) .

9. Remove Tooling (A) .

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

To prevent possible injury, follow the established assembly procedure

5. Carefully release the pressure on Tooling (A) .

Disassembly and Assembly

Inlet and Exhaust Valves - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Personal injury can result from being struck by parts propelled by a

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to

Ensure that the valve spring is compressed squarely or damage to the

6. Slowly release the pressure on Tooling (B) .

8. Use Tooling (C) in order to remove valve stem seal (6) .

9. Repeat Steps 4 through 7 for the remaining valves.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

To prevent possible injury, follow the established assembly procedure

To prevent possible injury, follow the established assembly procedure

7. Carefully release the pressure on Tooling (B) .

8. Repeat Steps 2 through 7 for the remaining valves.

Disassembly and Assembly

Inlet and Exhaust Valve Guides - Remove and Install

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Care must be taken to ensure that fluids are contained during

Refer to Special Publication, NENG2500, "Dealer Service Tool

Dispose of all fluids according to local regulations and mandates.

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Disassembly and Assembly

Engine Oil Cooler - Remove