Understand TCP/IP addressing and

subnetting basics
 09/21/2020
 12 minutes to read

o

 
o

This article is intended as a general introduction to the concepts of IP networks and

subnetting. A glossary is included at the end of article.

Original product version:   Windows 10 - all editions

Original KB number:   164015

Summary
When you configure the TCP/IP protocol on a Windows computer, an IP address, subnet
mask, and usually a default gateway are required in the TCP/IP configuration settings.

To configure TCP/IP correctly, it is necessary to understand how TCP/IP networks are

addressed and divided into networks and subnetworks.

The success of TCP/IP as the network protocol of the Internet is largely because of its
ability to connect together networks of different sizes and systems of different types.
These networks are arbitrarily defined into three main classes (along with a few others)
that have predefined sizes, each of which can be divided into smaller subnetworks by
system administrators. A subnet mask is used to divide an IP address into two parts. One
part identifies the host (computer), the other part identifies the network to which it
belongs. To better understand how IP addresses and subnet masks work, look at an IP
(Internet Protocol) address and see how it is organized.

IP addresses: Networks and hosts

An IP address is a 32-bit number that uniquely identifies a host (computer or other
device, such as a printer or router) on a TCP/IP network.
IP addresses are normally expressed in dotted-decimal format, with four numbers
separated by periods, such as 192.168.123.132. To understand how subnet masks are
used to distinguish between hosts, networks, and subnetworks, examine an IP address in
binary notation.

For example, the dotted-decimal IP address 192.168.123.132 is (in binary notation) the
32-bit number 110000000101000111101110000100. This number may be hard to make
sense of, so divide it into four parts of eight binary digits.

These eight-bit sections are known as octets. The example IP address, then, becomes
11000000.10101000.01111011.10000100. This number only makes a little more sense, so
for most uses, convert the binary address into dotted-decimal format (192.168.123.132).
The decimal numbers separated by periods are the octets converted from binary to
decimal notation.

For a TCP/IP wide area network (WAN) to work efficiently as a collection of networks,
the routers that pass packets of data between networks do not know the exact location
of a host for which a packet of information is destined. Routers only know what network
the host is a member of and use information stored in their route table to determine
how to get the packet to the destination host's network. After the packet is delivered to
the destination's network, the packet is delivered to the appropriate host.

For this process to work, an IP address has two parts. The first part of an IP address is
used as a network address, the last part as a host address. If you take the example
192.168.123.132 and divide it into these two parts, you get 192.168.123. Network .132
Host or 192.168.123.0 - network address. 0.0.0.132 - host address.

Subnet mask
The second item, which is required for TCP/IP to work, is the subnet mask. The subnet
mask is used by the TCP/IP protocol to determine whether a host is on the local subnet
or on a remote network.

In TCP/IP, the parts of the IP address that are used as the network and host addresses
are not fixed, so the network and host addresses above cannot be determined unless
you have more information. This information is supplied in another 32-bit number called
a subnet mask. In this example, the subnet mask is 255.255.255.0. It is not obvious what
this number means unless you know that 255 in binary notation equals 11111111; so,
the subnet mask is 11111111.11111111.11111111.0000000.
Lining up the IP address and the subnet mask together, the network, and host portions
of the address can be separated:

11000000.10101000.01111011.10000100 -- IP address (192.168.123.132)

11111111.11111111.11111111.00000000 -- Subnet mask (255.255.255.0)

The first 24 bits (the number of ones in the subnet mask) are identified as the network
address, with the last 8 bits (the number of remaining zeros in the subnet mask)
identified as the host address. This gives you the following:

11000000.10101000.01111011.00000000 -- Network address (192.168.123.0)

00000000.00000000.00000000.10000100 -- Host address (000.000.000.132)

So now you know, for this example using a 255.255.255.0 subnet mask, that the network
ID is 192.168.123.0, and the host address is 0.0.0.132. When a packet arrives on the
192.168.123.0 subnet (from the local subnet or a remote network), and it has a
destination address of 192.168.123.132, your computer will receive it from the network
and process it.

Almost all decimal subnet masks convert to binary numbers that are all ones on the left
and all zeros on the right. Some other common subnet masks are:

Decimal Binary 255.255.255.192 1111111.11111111.1111111.11000000 255.255.255.224

1111111.11111111.1111111.11100000

Internet RFC 1878 (available from InterNIC-Public Information Regarding Internet

Domain Name Registration Services) describes the valid subnets and subnet masks that
can be used on TCP/IP networks.

Network classes
Internet addresses are allocated by the InterNIC, the organization that administers the
Internet. These IP addresses are divided into classes. The most common of these are
classes A, B, and C. Classes D and E exist, but are not used by end users. Each of the
address classes has a different default subnet mask. You can identify the class of an IP
address by looking at its first octet. Following are the ranges of Class A, B, and C Internet
addresses, each with an example address:

 Class A networks use a default subnet mask of 255.0.0.0 and have 0-127 as their
first octet. The address 10.52.36.11 is a class A address. Its first octet is 10, which is
between 1 and 126, inclusive.
  Class B networks use a default subnet mask of 255.255.0.0 and have 128-191 as
their first octet. The address 172.16.52.63 is a class B address. Its first octet is 172,
which is between 128 and 191, inclusive.
 Class C networks use a default subnet mask of 255.255.255.0 and have 192-223
as their first octet. The address 192.168.123.132 is a class C address. Its first octet is
192, which is between 192 and 223, inclusive.

In some scenarios, the default subnet mask values do not fit the needs of the
organization, because of the physical topology of the network, or because the numbers
of networks (or hosts) do not fit within the default subnet mask restrictions. The next
section explains how networks can be divided using subnet masks.

Subnetting
A Class A, B, or C TCP/IP network can be further divided, or subnetted, by a system
administrator. This becomes necessary as you reconcile the logical address scheme of
the Internet (the abstract world of IP addresses and subnets) with the physical networks
in use by the real world.

A system administrator who is allocated a block of IP addresses may be administering

networks that are not organized in a way that easily fits these addresses. For example,
you have a wide area network with 150 hosts on three networks (in different cities) that
are connected by a TCP/IP router. Each of these three networks has 50 hosts. You are
allocated the class C network 192.168.123.0. (For illustration, this address is actually from
a range that is not allocated on the Internet.) This means that you can use the addresses
192.168.123.1 to 192.168.123.254 for your 150 hosts.

Two addresses that cannot be used in your example are 192.168.123.0 and
192.168.123.255 because binary addresses with a host portion of all ones and all zeros
are invalid. The zero address is invalid because it is used to specify a network without
specifying a host. The 255 address (in binary notation, a host address of all ones) is used
to broadcast a message to every host on a network. Just remember that the first and last
address in any network or subnet cannot be assigned to any individual host.

You should now be able to give IP addresses to 254 hosts. This works fine if all 150
computers are on a single network. However, your 150 computers are on three separate
physical networks. Instead of requesting more address blocks for each network, you
divide your network into subnets that enable you to use one block of addresses on
multiple physical networks.
In this case, you divide your network into four subnets by using a subnet mask that
makes the network address larger and the possible range of host addresses smaller. In
other words, you are 'borrowing' some of the bits used for the host address, and using
them for the network portion of the address. The subnet mask 255.255.255.192 gives
you four networks of 62 hosts each. This works because in binary notation,
255.255.255.192 is the same as 1111111.11111111.1111111.11000000. The first two
digits of the last octet become network addresses, so you get the additional networks
00000000 (0), 01000000 (64), 10000000 (128) and 11000000 (192). (Some administrators
will only use two of the subnetworks using 255.255.255.192 as a subnet mask. For more
information on this topic, see RFC 1878.) In these four networks, the last 6 binary digits
can be used for host addresses.

Using a subnet mask of 255.255.255.192, your 192.168.123.0 network then becomes the
four networks 192.168.123.0, 192.168.123.64, 192.168.123.128 and 192.168.123.192.
These four networks would have as valid host addresses:

192.168.123.1-62 192.168.123.65-126 192.168.123.129-190 192.168.123.193-254

Remember, again, that binary host addresses with all ones or all zeros are invalid, so you
cannot use addresses with the last octet of 0, 63, 64, 127, 128, 191, 192, or 255.

You can see how this works by looking at two host addresses, 192.168.123.71 and
192.168.123.133. If you used the default Class C subnet mask of 255.255.255.0, both
addresses are on the 192.168.123.0 network. However, if you use the subnet mask of
255.255.255.192, they are on different networks; 192.168.123.71 is on the 192.168.123.64
network, 192.168.123.133 is on the 192.168.123.128 network.

Default gateways
If a TCP/IP computer needs to communicate with a host on another network, it will
usually communicate through a device called a router. In TCP/IP terms, a router that is
specified on a host, which links the host's subnet to other networks, is called a default
gateway. This section explains how TCP/IP determines whether or not to send packets to
its default gateway to reach another computer or device on the network.

When a host attempts to communicate with another device using TCP/IP, it performs a
comparison process using the defined subnet mask and the destination IP address
versus the subnet mask and its own IP address. The result of this comparison tells the
computer whether the destination is a local host or a remote host.
If the result of this process determines the destination to be a local host, then the
computer will send the packet on the local subnet. If the result of the comparison
determines the destination to be a remote host, then the computer will forward the
packet to the default gateway defined in its TCP/IP properties. It is then the
responsibility of the router to forward the packet to the correct subnet.

Troubleshooting
TCP/IP network problems are often caused by incorrect configuration of the three main
entries in a computer's TCP/IP properties. By understanding how errors in TCP/IP
configuration affect network operations, you can solve many common TCP/IP problems.

Incorrect Subnet Mask: If a network uses a subnet mask other than the default mask for
its address class, and a client is still configured with the default subnet mask for the
address class, communication will fail to some nearby networks but not to distant ones.
As an example, if you create four subnets (such as in the subnetting example) but use
the incorrect subnet mask of 255.255.255.0 in your TCP/IP configuration, hosts will not
be able to determine that some computers are on different subnets than their own.
When this happens, packets destined for hosts on different physical networks that are
part of the same Class C address will not be sent to a default gateway for delivery. A
common symptom of this is when a computer can communicate with hosts that are on
its local network and can talk to all remote networks except those that are nearby and
have the same class A, B, or C address. To fix this problem, just enter the correct subnet
mask in the TCP/IP configuration for that host.

Incorrect IP Address: If you put computers with IP addresses that should be on separate
subnets on a local network with each other, they will not be able to communicate. They
will try to send packets to each other through a router that will not be able to forward
them correctly. A symptom of this problem is a computer that can talk to hosts on
remote networks, but cannot communicate with some or all computers on their local
network. To correct this problem, make sure all computers on the same physical network
have IP addresses on the same IP subnet. If you run out of IP addresses on a single
network segment, there are solutions that go beyond the scope of this article.

Incorrect Default Gateway: A computer configured with an incorrect default gateway will
be able to communicate with hosts on its own network segment, but will fail to
communicate with hosts on some or all remote networks. If a single physical network
has more than one router, and the wrong router is configured as a default gateway, a
host will be able to communicate with some remote networks, but not others. This
problem is common if an organization has a router to an internal TCP/IP network and
another router connected to the Internet.

References