Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 77 views

    Installation Instruction: For 1/2"R Annular Corrugation Cable

    Uploaded by

    nguyentraihd
    This document provides installation instructions for 1/2" annular corrugated cable in 3 steps or less: 1. Prepare the cable end by cutting it to length and stripping insulation to expose the conductors. 2. Attach connectors to the cable by sliding on a back nut, pressing on a clamp ring, and flaring the outer conductor. 3. Tighten the connectors by hand and wrench to complete the installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Installation Instruction: For 1/2"R Annular Corrugation Cable

    Uploaded by

    nguyentraihd
    77 views2 pages
    This document provides installation instructions for 1/2" annular corrugated cable in 3 steps or less: 1. Prepare the cable end by cutting it to length and stripping insulation to expose the conductors. 2. Attach connectors to the cable by sliding on a back nut, pressing on a clamp ring, and flaring the outer conductor. 3. Tighten the connectors by hand and wrench to complete the installation.

    Original Title

    12r

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides installation instructions for 1/2" annular corrugated cable in 3 steps or less: 1. Prepare the cable end by cutting it to length and stripping insulation to expose the conductors. 2. Attach connectors to the cable by sliding on a back nut, pressing on a clamp ring, and flaring the outer conductor. 3. Tighten the connectors by hand and wrench to complete the installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    77 views2 pages

    Installation Instruction: For 1/2"R Annular Corrugation Cable

    Uploaded by

    nguyentraihd
    This document provides installation instructions for 1/2" annular corrugated cable in 3 steps or less: 1. Prepare the cable end by cutting it to length and stripping insulation to expose the conductors. 2. Attach connectors to the cable by sliding on a back nut, pressing on a clamp ring, and flaring the outer conductor. 3. Tighten the connectors by hand and wrench to complete the installation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    Installation Instruction

    No. : MA_C7-C03
    for 1/2”R annular corrugation cable Revision A 6/2007

    7/16 DIN 7/16 DIN N TYPE N TYPE


    Female Male Male Female

    60K1C7-C03N1 60S1C7-C03N1 53S1C7-C03N1 53K1C7-C03N1


    Sealing nut
    Front nut
    20# 20#
    Clamp ring

    4
    Flaring Tool

    60W007-C03(1C7)
    Tools
    Back nut

    3
    a

    2
    1
    1． Cut your cable at corrugation top 2． Strip the cable. Press against the cable using 3. If the outer conductor have been cut at
    using hacksaw or other tools, then stripping tool and turn slowly until stripping corrugation top(as photo 4) then go to step5,
    straighten the cable end for end. Note: Be careful not to scrape center otherwise take notice of length “a”.
    approximate 200mm. conductor.

    Inches
    a 14.5+0.5 7±0.3 Edge
    100
    P P

    90
    80

    C0.3
    Corrugation top
    70

    4．Cut the center conductor for a length 5． Strip the cable again. Gently turn the tool to 6 Be sure the outer conductor is round and
    60

    “a” by pliers. prevent outer conductor distorted. Properly undistorted. You can use tools to make it
    prepared cable end as the photo shows. round if necessary..
    50
    40
    30
    20
    10
    mm
    7. Slide back nut onto the cable until it is 8. Press clamp ring on to out conductor, 9. Insert center conductor into flaring
    completely seated. Please loose sealing nut in
    tool’s guide hole, then press and spin the
    order to easy to install back nut
    tool to flare outer conductor.

    10.Proper shape after flaring operation. 11. Deburr by brush.


    Please don’t hurt inner contact 12．Push cable back until clamp ring slide
    into slot of back nut

    15.Tighten sealing nut with wenches


    13.Tighten front nut with back nut by hands 14.Tighten front nut and back nut with
    wenches until stop

    16.Finished.

    Note:
    1) Please refer to related instruction to use 60W007-C03(1C7) stripping tool;
    2) You can use other tools to get proper shape and size as photo 5 shows;
    3) Information in this instruction is subject to change without notice;
    4) ROSENBERGER disclaims any responsibility for the result of improper usage.

    Rosenberger Asia Pacific Electronic Co., Ltd.


    No. 3 Anxiang Street, Block B, Tianzhu Airport Industrial Zone,
    101300 Beijing, P. R. China

    Tel: 0086 10 80481995


    Fax:0086 10 80482438

    You might also like