Promass 80E - TI00061DEN

Technical Information
Proline Promass 80E, 83E

Coriolis Mass Flow Measuring System
Mass flow measuring system offering "Low Cost of Ownership" as
an alternative to conventional volumetric flowmeters
Application Your benefits

The Coriolis measuring principle operates independently The Promass measuring devices make it possible
of physical fluid properties, such as viscosity and density. to simultaneously record several process variables
(mass/density/temperature) for various process
• Extremely accurate measurement of liquids and gases,
conditions during measuring operation.
e.g. additives, oils, greases, acids, alkalis, lacquers,
paints and natural gas The Proline transmitter concept comprises:
• Fluid temperatures up to +140 °C (+284 °F) • Modular device and operating concept resulting
• Guaranteed product quality, suitable for CIP/SIP in a higher degree of efficiency
cleaning • Software options for batching and concentration
• Low cost of ownership measurement for extended range of application
• Robust field housing (aluminum), IP 67 protection • Diagnostic ability and data back-up for increased
process quality
Approvals for hazardous area:
• ATEX, FM, CSA, TIIS, IECEx, NEPSI The Promass sensors, tried and tested in over 100000
applications, offer:
Approvals in the food industry/hygiene sector:
• Multivariable flow measurement in compact design
• 3A authorization
• Insensitivity to vibrations thanks to balanced
Connection to all common process control systems: two-tube measuring system
• HART, PROFIBUS DP/PA, FOUNDATION Fieldbus, • Immune from external piping forces due
MODBUS to robust design
Relevant safety aspects: • Easy installation without taking inlet and outlet
• Pressure Equipment Directive (PED), SIL-2 runs into consideration
• Rupture disk (optional)
TI00061D/06/EN/13.11
71129459
Table of contents
Function and system design. . . . . . . . . . . . . . . . . . . . . 3 Limiting flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 23
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Design, dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Rupture disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Operable flow range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Material load curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Process connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Low flow cutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Language groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Switching output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 46
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection Measuring unit . . . . . . . . . . . . . . . . . . . . . 10 C-Tick symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection, terminal assignment . . . . . . . . . . . . . . . . . 11 Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection remote version . . . . . . . . . . . . . . . . . . . . . . 12 Hygienic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FOUNDATION Fieldbus certification . . . . . . . . . . . . . . . . . . . . 46
Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 PROFIBUS DP/PA certification . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cable specification remote version . . . . . . . . . . . . . . . . . . . . . . . 12 MODBUS certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Other standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Pressure Equipment Directive . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Functional safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Performance characteristics. . . . . . . . . . . . . . . . . . . . 14 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . 47

Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maximum measured error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Repeatability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Influence of fluid temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Influence of fluid pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Design fundamentals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . 48
Operating conditions: Installation . . . . . . . . . . . . . . . 17
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Inlet and outlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Length of connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
System pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating conditions: Environment. . . . . . . . . . . . . . 20

Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . 20
Operating conditions: Process . . . . . . . . . . . . . . . . . . 21

Fluid temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Fluid density range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Fluid pressure range (nominal pressure) . . . . . . . . . . . . . . . . . . . 21
Rupture disk in the sensor housing (optional) . . . . . . . . . . . . . . . 21
2 Endress+Hauser
Function and system design

Measuring principle The measuring principle is based on the controlled generation of Coriolis forces. These forces are always present
when both translational and rotational movements are superimposed.
FC = 2 · m (v · )
FC = Coriolis force
m = moving mass
 = rotational velocity
v = radial velocity in rotating or oscillating system
The amplitude of the Coriolis force depends on the moving mass m, its velocity v in the system, and thus on
the mass flow. Instead of a constant angular velocity , the Promass sensor uses oscillation.
In the sensor, two parallel measuring tubes containing flowing fluid oscillate in antiphase, acting like a tuning
fork. The Coriolis forces produced at the measuring tubes cause a phase shift in the tube oscillations (see
illustration):
• At zero flow, in other words when the fluid is at a standstill, the two tubes oscillate in phase (1).
• Mass flow causes deceleration of the oscillation at the inlet of the tubes (2) and acceleration at the outlet (3).
A A A
B B B
1 2 3
a0003385
The phase difference (A-B) increases with increasing mass flow. Electrodynamic sensors register the tube
oscillations at the inlet and outlet.
System balance is ensured by the antiphase oscillation of the two measuring tubes. The measuring principle
operates independently of temperature, pressure, viscosity, conductivity and flow profile.
Volume measurement
The measuring tubes are continuously excited at their resonance frequency. A change in the mass and thus the
density of the oscillating system (comprising measuring tubes and fluid) results in a corresponding, automatic
adjustment in the oscillation frequency. Resonance frequency is thus a function of fluid density. The density
value obtained in this way can be used in conjunction with the measured mass flow to calculate the volume
flow.
The temperature of the measuring tubes is also determined in order to calculate the compensation factor due
to temperature effects.
Endress+Hauser 3
Measuring system The measuring system consists of a transmitter and a sensor. Two versions are available:
• Compact version: transmitter and sensor form a mechanical unit.
• Remote version: transmitter and sensor are mounted physically separate from one another.
Transmitter
Promass 80 • Two-line liquid-crystal display

• Operation with push buttons
Esc
- + E
a0003671
Promass 83 • Four-line liquid-crystal display

• Operation with “Touch control”
• Application-specific Quick Setup
• Mass flow, volume flow, density and temperature measurement as well as
calculated variables (e.g. fluid concentrations)
Esc
– + E
a0003672
Sensor
E • General purpose sensor, ideal replacement for volumetric Documentation No.

flowmeters. TI061D
• Nominal diameters DN 8 to 80 (3/8" to 3")
• Material: Stainless steel EN 1.4539/ASTM 904L,
EN 1.4404/ASTM 316L
a0002271
Other sensors can be found in the separate documentation
A • Single-tube system for highly accurate measurement of Documentation No.

very small flows TI054D
• Nominal diameters DN 1 to 4 (1/24" to 1/8")
EN 1.4404/ASTM 316L , Alloy C-22 DIN 2.4602
(process connection)
a0003679
F • Universal sensor for fluid temperatures Documentation No.

up to +200 °C (+392 °F). TI101D
• Nominal diameters DN 8 to 250 (3/8" to 10").
EN 1.4404/ASTM 316L, Alloy C-22 DIN 2.4602
a0003673
F (High-temperature) • Universal high-temperature sensor for fluid temperatures

up to +350 °C +(+662 °F).
• Nominal diameters DN 25, 50, 80 (1", 2", 3")
• Material: Alloy C-22, DIN 2.4602,
EN 1.4404/ASTM 316L
a0003675
4 Endress+Hauser
H • Single bent tube. Low pressure loss and chemically Documentation No.
resistant material TI074D
• Material: Zirconium 702/R 60702, Tantalum 2.5W
a0003677
I • Straight single-tube instrument. Minimal shear stress on Documentation No.

fluid, hygienic design, low pressure loss TI075D
• Material: Titanium, Ti Grade 2, Ti Grade 9
a0003678
P • Single bent tube, minimal shear stress on fluid. Documentation No.

Hygienic design with documents for Life Science TI078D
Industries applications, low pressure loss, for fluid
temperatures up to +200 °C (+392 °F).
• Material: Stainless steel EN 1.4435/ASTM 316L
a0006828
S • Single bent tube. Documentation No.

Hygienic design, low pressure loss, for fluid temperatures TI076D
up to 150 °C (+302 °F)
• Material: Stainless steel, EN 1.4539/ASTM 904L,
EN 1.4435/ASTM 316L
a0006828
Endress+Hauser 5
Input
Measured variable • Mass flow (proportional to the phase difference between two sensors mounted on the measuring tube to
register a phase shift in the oscillation)
• Fluid density (proportional to resonance frequency of the measuring tube)
• Fluid temperature (measured with temperature sensors)
Measuring range Measuring ranges for liquids
DN Range for full scale values (liquids) gmin(F) to gmax(F)
[mm] [inch] [kg/h] [lb/min]
8 3/8" 0 to 2000 0 to 73.5
15 ½" 0 to 6500 0 to 238
25 1" 0 to 18000 0 to 660
40 1 ½" 0 to 45000 0 to 1650
50 2" 0 to 70000 0 to 2570
80 3" 0 to 180000 0 to 6600
Measuring ranges for gases

The full scale values depend on the density of the gas. Use the formula below to calculate the full scale values:
gmax(G) = gmax(F) · (G) ÷ x [kg/m³]
gmax(G) = max. full scale value for gas [kg/h]
gmax(F) = max. full scale value for liquid [kg/h]
(G) = Gas density in [kg/m³] at operating conditions
DN
x
[mm] [inch]
8 3/8" 85
15 ½" 110
25 1" 125
40 1 ½" 125
50 2" 125
80 3" 155
Here, gmax(G) can never be greater than gmax(F)
Calculation example for gas:

• Sensor type: Promass E, DN 50
• Gas: air with a density of 60.3 kg/m³ (at 20 °C and 50 bar)
• Measuring range (liquid): 70000 kg/h
• x = 125 (for Promass E, DN 50)
Max. possible full scale value:
gmax(G) = gmax(F) · (G) ÷ x [kg/m³] = 70000 kg/h · 60.3 kg/m³ ÷ 125 kg/m³ = 33800 kg/h
Recommended full scale values

See information in the "Limiting flow" section  ä 21 ff.
6 Endress+Hauser
Operable flow range Greater than 1000: 1. Flow rates above the preset full scale value do not overload the amplifier, i.e. the totalizer
values are registered correctly.
Input signal Status input (auxiliary input)

U = 3 to 30 V DC, Ri = 5 k, galvanically isolated.
Configurable for: totalizer reset, positive zero return, error message reset, zero point adjustment start,
batching start/stop (optional), batch totalizer reset (optional).
Status input (auxiliary input) with PROFIBUS DP

Switch level: ±3 to ±30 V DC, independent of polarity.
Configurable for: positive zero return, error message reset, zero point adjustment start,
batching start/stop (optional), totalizer reset for batching (optional).
Status input (auxiliary input) with MODBUS RS485

Switch level: ±3 to ±30 V DC, independent of polarity.
Configurable for: totalizer reset, positive zero return, error message reset, zero point adjustment start.
Current input (only Promass 83)

Active/passive selectable, galvanically isolated, resolution: 2 μA
• Active: 4 to 20 mA, RL < 700 , Uout = 24 V DC, short-circuit proof
• Passive: 0/4 to 20 mA, Ri = 150 , Umax = 30 V DC
Output
Output signal Promass 80
Current output
Active/passive selectable, galvanically isolated, time constant selectable (0.05 to 100 s), full scale value
selectable, temperature coefficient: typically 0.005% o.f.s./°C, resolution: 0.5 μA
• Active: 0/4 to 20 mA, RL < 700  (for HART: RL  250 )
• Passive: 4 to 20 mA; supply voltage US 18 to 30 V DC; Ri  150 
Pulse/frequency output
Passive, open collector, 30 V DC, 250 mA, galvanically isolated.
• Frequency output: full scale frequency 2 to 1000 Hz (fmax = 1250 Hz), on/off ratio 1:1, pulse width max. 2 s
• Pulse output: pulse value and pulse polarity selectable, pulse width configurable (0.5 to 2000 ms)
PROFIBUS PA interface
• PROFIBUS PA in accordance with EN 50170 Volume 2, IEC 61158-2 (MBP), galvanically isolated
• Profile Version 3.0
• Current consumption: 11 mA
• Permitted supply voltage: 9 to 32 V
• Bus connection with integrated reverse polarity protection
• Error current FDE (Fault Disconnection Electronic) = 0 mA
• Data transmission rate: 31.25 kBit/s
• Signal encoding: Manchester II
• Function blocks: 4 × Analog Input, 2 × Totalizer
• Output data: Mass flow, Volume flow, Density, Temperature, Totalizer
• Input data: Positive zero return (ON/OFF), Zero point adjustment, Measuring mode, Totalizer control
• Bus address can be configured via miniature switches or via the local display (optional)
Endress+Hauser 7
Promass 83
Current output
Active/passive selectable, galvanically isolated, time constant selectable (0.05 to 100 s), full scale value
selectable, temperature coefficient: typically 0.005% o.f.s./°C, resolution: 0.5 μA
• Active: 0/4 to 20 mA, RL < 700  (for HART: RL  250 )
• Passive: 4 to 20 mA; supply voltage US 18 to 30 V DC; Ri  150 
active/passive selectable, galvanically isolated
• Active: 24 V DC, 25 mA (max. 250 mA during 20 ms), RL > 100 
• Passive: open collector, 30 V DC, 250 mA
• Frequency output: full scale frequency 2 to 10000 Hz (fmax = 12500 Hz), on/off ratio 1:1,
pulse width max. 2 s
• Pulse output: pulse value and pulse polarity selectable, pulse width configurable (0.05 to 2000 ms)
PROFIBUS DP interface
• PROFIBUS DP in accordance with EN 50170 Volume 2
• Profile Version 3.0
• Data transmission rate: 9.6 kBaud to 12 MBaud
• Automatic data transmission rate recognition
• Signal encoding: NRZ Code
• Output data: Mass flow, Volume flow, Corrected volume flow, Density, Reference density, Temperature,
Totalizers 1 to 3
• Available output combination  ä 11
PROFIBUS PA interface
• PROFIBUS PA in accordance with EN 50170 Volume 2, IEC 61158-2 (MBP), galvanically isolated
• Bus connection with
integrated reverse polarity protection
• Error current FDE (Fault Disconnection Electronic): 0 mA
Totalizers 1 to 3
• Available output combination  ä 11
MODBUS interface
• MODBUS device type: slave
• Address range: 1 to 247
• Supported function codes: 03, 04, 06, 08, 16, 23
• Broadcast: supported with the function codes 06, 16, 23
• Physical interface: RS485 in accordance with EIA/TIA-485 standard
• Supported baud rate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Baud
• Transmission mode: RTU or ASCII
• Response times:
Direct data access = typically 25 to 50 ms
Auto-scan buffer (data range) = typically 3 to 5 ms
• Possible output combination  ä 11
8 Endress+Hauser
FOUNDATION Fieldbus interface

• FOUNDATION Fieldbus H1, IEC 61158-2, galvanically isolated
• Error current FDE (Fault Disconnection Electronic): 0 mA
• Bus connection with integrated reverse polarity protection
• ITK Version 5.01
• Function blocks:
– 8 × Analog Input (Execution time: per18 ms)
– 1 × Digital Output (18 ms)
– 1 × PID (25 ms)
– 1 × Arithmetic (20 ms)
– 1 × Input Selector (20 ms)
– 1 × Signal Characterizer (20 ms)
– 1 × Integrator (18 ms)
• Number of VCRs: 38
• Number of link objects in VFD: 40
Totalizers 1 to 3
• Input data: Positive zero return (ON/OFF), Zero point adjustment, Measuring mode, Reset totalizer
• Link Master (LM) function is supported
Signal on alarm Current output

Failsafe mode selectable (e.g. in accordance with NAMUR Recommendation NE 43)
Failsafe mode selectable
Status output (Promass 80)

Nonconductive in the event of a fault or if the power supply fails
Relay output (Promass 83)

Dead in the event of a fault or if the power supply fails
Load see "Output signal"
Low flow cutoff Switch points for low flow are selectable.
Galvanic isolation All circuits for inputs, outputs, and power supply are galvanically isolated from each other.
Switching output Status output (Promass 80)

• Open collector
• max. 30 V DC / 250 mA
• galvanically isolated
• Configurable for: error messages, Empty Pipe Detection (EPD), flow direction, limit values
Relay output (Promass 83)

• max. 30 V / 0.5 A AC; 60 V / 0.1 A DC
• galvanically isolated
• Normally closed (NC or break) or normally open (NO or make) contacts available
(factory setting: relay 1 = NO, relay 2 = NC)
Endress+Hauser 9
Power supply
Electrical connection
Measuring unit A B C
d d
g g
b b
a
a
a
b d/(g) (d)
HART* PROFIBUS PA*

FOUNDATION Fieldbus*
– 27 PA(–)/FF(–) 27
+ 26 PA(+)/FF(+) 26
– 25 d – 25 d
+ 24 + 24
f – 23 e f – 23 e
+ 22 + 22
– 21 – 21
+ 20 + 20
N (L-) 2 c N (L-) 2 c
L1 (L+)1 L1 (L+) 1
b b
PROFIBUS DP* PROFIBUS DP**

MODBUS RS485**
A (RxD/TxD-N) 27 A (RxD/TxD-N) 27
B (RxD/TxD-P) 26 B (RxD/TxD-P) 26
– 25 d – 25 d
+ 24 + 24
f – 23 e f – 23 e
+ 22 + 22
– 21 – 21
+ 20 g + 20 g
N (L-) 2 c N (L-) 2
c
L1 (L+) 1 L1 (L+) 1
b b
a0002441
Connecting the transmitter, cable cross-section: max. 2.5 mm2

A View A (field housing)
B View B (Stainless Steel field housing)
C View C (wall-mount housing)
*) fixed communication board
**) flexible communication board
a Connection compartment cover
b Cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
c Ground terminal for protective ground
d Signal cable: see Terminal assignment  ä 11
Fieldbus cable:
Terminal No. 26: DP (B) / PA (+) / FF (+) / MODBUS RS485 (B) / (PA, FF: with reverse polarity protection)
Terminal No. 27: DP (A) / PA (–) / FF (–) / MODBUS RS485 (A) / (PA, FF: with reverse polarity protection)
e Ground terminal for signal cable shield / fieldbus cable / RS485 line
f Service adapter for connecting service interface FXA 193 (Fieldcheck, FieldCare)
g Signal cable: see Terminal assignment  ä 11
g Cable for external termination (only for PROFIBUS DP with permanent assignment communication board):
Terminal No. 24: +5 V
Terminal No. 25: DGND
10 Endress+Hauser
Electrical connection, Promass 80

terminal assignment
Terminal No. (inputs/outputs)
Order version 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
80***-***********A - - Frequency output Current output, HART
80***-***********D Status input Status output Frequency output Current output, HART
80***-***********H - - - PROFIBUS PA
Frequency output Current output Ex i

80***-***********S - -
Ex i, passive active, HART

80***-***********T - -
Ex i, passive passive, HART
80***-***********8 Status input Frequency output Current output 2 Current output 1, HART
Promass 83
The inputs and outputs on the communication board can be either permanently assigned (fixed) or variable
(flexible), depending on the version ordered (see table). Replacements for modules which are defective or
which have to be replaced can be ordered as accessories.
Order version 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
Fixed communication boards (permanent assignment)
83***-***********A - - Frequency output Current output, HART
83***-***********B Relay output Relay output Frequency output Current output, HART
83***-***********F - - - PROFIBUS PA, Ex i
FOUNDATION
83***-***********G - - -
Fieldbus Ex i
83***-***********H - - - PROFIBUS PA
83***-***********J - - +5V (ext. termination) PROFIBUS DP
83***-***********K - - - FOUNDATION Fieldbus
83***–***********Q - - Status input MODBUS RS485
83***-***********R - - Current output 2 Current output 1

Ex i, active Ex i active, HART

83***-***********S - -
Ex i, passive active, HART

83***-***********T - -
Ex i, passive passive, HART
83***-***********U - - Current output 2 Current output 1

Ex i, passive Ex i passive, HART
Flexible communication boards
83***-***********C Relay output 2 Relay output 1 Frequency output Current output, HART
83***-***********D Status input Relay output Frequency output Current output, HART
83***-***********E Status input Relay output Current output 2 Current output 1, HART
83***-***********L Status input Relay output 2 Relay output 1 Current output, HART
83***-***********M Status input Freq.output 2 Frequency output 1 Current output, HART
83***–***********N Current output Frequency output Status input MODBUS RS485
83***–***********P Current output Frequency output Status input PROFIBUS DP
83***–***********V Relay output 2 Relay output 1 Status input PROFIBUS DP
83***-***********W Relay output Current output 3 Current output 2 Current output 1, HART
Endress+Hauser 11
Order version 20 (+) / 21 (–) 22 (+) / 23 (–) 24 (+) / 25 (–) 26 (+) / 27 (–)
83***-***********0 Status input Current output 3 Current output 2 Current output 1, HART
83***-***********2 Relay output Current output 2 Frequency output Current output 1, HART
83***-***********3 Current input Relay output Current output 2 Current output 1, HART
83***-***********4 Current input Relay output Frequency output Current output, HART
83***-***********5 Status input Current input Frequency output Current output, HART
83***-***********6 Status input Current input Current output 2 Current output 1, HART
83***–***********7 Relay output 2 Relay output 1 Status input MODBUS RS485
Electrical connection remote

version S1 S1 S2 S2 GND TM TM TT TT
a b + + + +
4 5 6 7 8 9 10 11 12 41 42
d
d
d
e
c
4 5 6 7 8 9 10 11 12 41 42
+ + + +
S1 S1 S2 S2 GND TM TM TT TT
a0003681
Connecting the remote version

a Wall-mount housing: non-hazardous area and ATEX II3G / zone 2  see separate "Ex documentation"
b Wall-mount housing: ATEX II2G / Zone 1 /FM/CSA  see separate "Ex documentation"
c Connection housing sensor
d Cover for connection compartment or connection housing
e Connecting cable
Terminal No.: 4/5 = gray; 6/7 = green; 8 = yellow; 9/10 = pink; 11/12 = white; 41/42 = brown
Supply voltage 85 to 260 V AC, 45 to 65 Hz

20 to 55 V AC, 45 to 65 Hz
16 to 62 V DC
Cable entries Power-supply and signal cables (inputs/outputs):

• Cable entry M20 × 1.5 (8 to 12 mm / 0.31" to 0.47")
• Thread for cable entries, ½" NPT, G ½"
Connecting cable for remote version:
• Cable entry M20 × 1.5 (8 to 12 mm / 0.31" to 0.47")
• Thread for cable entries, ½" NPT, G ½"
Cable specification remote • 6 × 0.38 mm PVC cable with common shield and individually shielded cores
version • Conductor resistance:  50 /km (0.015 /ft)
• Capacitance: core/shield:  420 pF/m (128 pF/ft)
• Cable length: max. 20 m (65 ft)
• Permanent operating temperature: max. +105 °C (+221 °F)
Operation in zones of severe electrical interference:
The measuring device complies with the general safety requirements in accordance with EN 61010-1,
the EMC requirements of IEC/EN 61326, and NAMUR recommendation NE 21/43.
12 Endress+Hauser
Power consumption AC: <15 VA (including sensor)

DC: <15 W (including sensor)
Switch-on current
• Max. 13.5 A (<50 ms) at 24 V DC
• Max. 3 A (<5 ms) at 260 V AC
Power supply failure Promass 80

Lasting min. 1 power cycle:
• EEPROM saves measuring system data if the power supply fails
• HistoROM/S-DAT: exchangeable data storage chip with sensor specific data (nominal diameter, serial
number, calibration factor, zero point, etc.)
Promass 83
Lasting min. 1 power cycle:
• EEPROM and T-DAT save the measuring system data if the power supply fails.
• HistoROM/S-DAT: exchangeable data storage chip with sensor specific data (nominal diameter, serial
number, calibration factor, zero point, etc.)
Potential equalization No special measures for potential equalization are required. For instruments for use in hazardous areas, observe
the corresponding guidelines in the specific Ex documentation.
Endress+Hauser 13
Performance characteristics
Reference operating • Error limits following ISO/DIN 11631
conditions • Water, typically +15…+45 °C (+59…+113 °F); 2…6 bar (29…87 psi)
• Data according to calibration protocol ±5 °C (±9 °F) und ±2 bar (±29 psi)
• Accuracy based on accredited calibration rigs according to ISO 17025
Maximum measured error The following values refer to the pulse/frequency output. Measured error at the current output is typically
±5 μA. Design fundamentals  ä 16.
o.r. = of reading; 1 g/cm = 1 kg/l; T = medium temperature
Mass flow and volume flow (liquids)

Promass 83E:
• ±0.2% o.r.
Promass 80E:
• ±0.25% o.r.
Mass flow (gases)

Promass 83E, 80E: ±0.75% o.r.
Density (liquids)
• Reference conditions: ±0.0005 g/cm³

• Field density calibration: ±0.0005 g/cm³
(valid after a field density calibration under process conditions)
• Standard density calibration: ±0.02 g/cm³
(valid over the entire temperature and density range  ä 21)
Temperature
±0.5 °C ± 0.005 · T °C (±1 °F ± 0.003 · (T - 32) °F)
Zero point stability
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8" 0.20 0.0074
15 ½" 0.65 0.0239
25 1" 1.80 0.0662
40 1½" 4.50 0.1654
50 2" 7.00 0.2573
80 3" 18.00 0.6615
14 Endress+Hauser
Example for max. measured error
[%]
±1.0
±0.5
±0.2
0
0 1 2 4 6 8 10 12 14 16 18 t/h
a0006891
Max. measured error in % of measured value (example: Promass 83E / DN 25)
Flow values (example)

Design fundamentals  ä 16
Turn down Flow Max. measured error
[kg/h] or [l/h] [lb/min] [% o.r.]
250 : 1 72 2.646 2.50
100 : 1 180 6.615 1.00
25 : 1 720 26.46 0.25
10 : 1 1800 66.15 0.25
2:1 9000 330.75 0.25
o.r. = of reading
Repeatability Design fundamentals  ä 16.
Mass flow and volume flow (liquids)

Promass 80E, 83E: ±0.10% o.r.
Mass flow (gases)

Promass 80E, 83E: ±0.35% o.r.
Density (liquids)
±0.00025 g/cm³
Temperature
±0.25 °C ± 0.0025 · T °C (±1 °F ± 0.003 · (T – 32) °F)
Influence of fluid temperature When there is a difference between the temperature for zero point adjustment and the process temperature,
the typical measured error of the Promass sensor is ±0.0002% of the full scale value / °C (±0.0001% of the
full scale value / °F).
Influence of fluid pressure The table below shows the effect on accuracy of mass flow due to a difference between calibration pressure
and process pressure.
Endress+Hauser 15
DN Promass E
[mm] [inch] [% o.r./bar]
8 3/8" no influence
15 ½" no influence
25 1" no influence
40 1½" no influence
50 2" –0.009
80 3" –0.020
o.r. = of reading
Design fundamentals Dependent on the flow:

• Flow  Zero point stability ÷ (base accuracy ÷ 100)
– Max. measured error: ±base accuracy in % o.r.
– Repeatability: ± ½ · base accuracy in % o.r.
• Flow < Zero point stability ÷ (base accuracy ÷ 100)
– Max. measured error: ± (zero point stability ÷ measured value) · 100% o.r.
– Repeatability: ± ½ · (zero point stability ÷ measured value) · 100% o.r.
o.r. = of reading
Base accuracy for Promass 83E Promass 80E
Mass flow liquids 0.2 0.25
Volume flow liquids 0.2 0.25
Mass flow gases 0.75 0.75
16 Endress+Hauser
Operating conditions: Installation

Installation instructions Note the following points:
• No special measures such as supports are necessary. External forces are absorbed by the construction of the
instrument, for example the secondary containment.
• The high oscillation frequency of the measuring tubes ensures that the correct operation of the measuring
system is not influenced by pipe vibrations.
• No special precautions need to be taken for fittings which create turbulence (valves, elbows, T-pieces etc.),
as long as no cavitation occurs.
Mounting location
Entrained air or gas bubbles in the measuring tube can result in an increase in measuring errors.
Therefore, avoid the following mounting locations in the pipe installation:
• Highest point of a pipeline. Risk of air accumulating.
• Directly upstream of a free pipe outlet in a vertical pipeline.
a0003605
Mounting location
Notwithstanding the above, the installation proposal below permits installation in an open vertical pipeline.
Pipe restrictions or the use of an orifice with a smaller cross-section than the nominal diameter prevent the
sensor running empty while measurement is in progress.
5
a0003597
Installation in a down pipe (e.g. for batching applications)

1 Supply tank
2 Sensor
3 Orifice plate, pipe restriction (see Table following page)
4 Valve
5 Batching tank
Endress+Hauser 17
DN  Orifice plate, pipe restriction
[mm] [inch] [mm] [inch]
8 3/8" 6 0.24
15 ½" 10 0.40
25 1" 14 0.55
40 1½" 22 0.87
50 2" 28 1.10
80 3" 50 2.00
Orientation
Make sure that the direction of the arrow on the nameplate of the sensor matches the direction of flow
(direction of fluid flow through the pipe).
Vertical (Fig. V)
Recommended orientation with upward direction of flow. When fluid is not flowing, entrained solids will sink
down and gases will rise away from the measuring tube. Thus the measuring tubes can be completely drained
and protected against solids buildup.
Horizontal (Fig. H1 / H2)

The measuring tubes must be horizontal and beside each other. When installation is correct the transmitter
housing is above or below the pipe (Fig. H1/H2). Always avoid having the transmitter housing in the same
horizontal plane as the pipe. Please note the special installation instructions  ä 19.
Orientation Promass E Promass E

compact version remote version
Fig. V:
ÃÃ ÃÃ
Vertical
a0004572
Fig. H1:
Horizontal ÃÃ ÃÃ
Transmitter head up
a0004576
Fig. H2:
Horizontal ÃÃ ÃÃ
Transmitter head down
a0004580
Fig. H3:
Horizontal ✘ ✘
Transmitter head to the side
a0007558
ÃÃ = Recommended orientation
Ã = Orientation recommended in certain situations
✘ = Impermissible orientation
In order to ensure that the permissible ambient temperature range for the transmitter is not exceeded, we
recommend the following orientations:
• For fluids with very high temperatures, we recommend the horizontal orientation with the transmitter head
pointing downwards (Fig. H2) or the vertical orientation (Fig. V).
18 Endress+Hauser
• For fluids with very low temperatures, we recommend the horizontal orientation with the transmitter head
pointing upwards (Fig. H1) or the vertical orientation (Fig. V).
Special installation instructions
" Caution!
When using a bent measuring tube and horizontal installation, the position of the sensor has to be matched to
the fluid properties!
1 2
a0004581
Horizontal installation for sensors with a bent measuring tube

1 Not suitable for fluids with entrained solids. Risk of solids accumulating.
2 Not suitable for outgassing fluids. Risk of air accumulating.
Heating
Some fluids require suitable measures to avoid heat transfer at the sensor. Heating can be electric, e.g. with
heated elements, or by means of hot water or steam pipes made of copper or heating jackets.
" Caution!
• Risk of electronics overheating! Make sure that the maximum permissible ambient temperature for the
transmitter is not exceeded. Consequently, make sure that the adapter between the sensor and transmitter
and the connection housing of the remote version always remain free of insulating material. Note that a
certain orientation might be required, depending on the fluid temperature  ä 21.
• If using an electric trace heating system whose heating is regulated via phase angle control or pulse packages,
influence on the measured values cannot be ruled out due to magnetic fields (i.e. for values that are greater
than the values approved by the EN standard (sine 30 A/m)). In such cases, the sensor must be magnetically
shielded.
The housing can be shielded with tin plates or electric sheets without preferential direction (e.g. V330-35A)
with the following properties:
– Relative magnetic permeability μr  300
– Plate thickness d  0.35 mm (d 0.014")
• Information on permitted temperature ranges  ä 21
Special heating jackets, which can be ordered separately from Endress+Hauser as an accessory, are available
for the sensors.
Thermal insulation
Some fluids require suitable measures to avoid loss of heat at the sensor. A wide range of materials can be used
to provide the required thermal insulation.
Zero point adjustment

All measuring devices are calibrated with state-of-the-art technology. The zero point determined in this
way is imprinted on the nameplate of the device. Calibration takes place under reference operating
conditions  ä 14. Consequently, the zero point adjustment is generally not necessary for Promass!
Experience shows that the zero point adjustment is advisable only in special cases:
• To achieve highest measuring accuracy also with very small flow rates.
• Under extreme process or operating conditions (e.g. very high process temperatures or very high viscosity
fluids).
Endress+Hauser 19
Inlet and outlet runs There are no installation requirements regarding inlet and outlet runs.
Length of connecting cable Max. 20 meters (66 ft), remote version
System pressure It is important to ensure that cavitation does not occur, because it would influence the oscillation of the
measuring tube. No special measures need to be taken for fluids which have properties similar to water under
normal conditions.
In the case of liquids with a low boiling point (hydrocarbons, solvents, liquefied gases) or in suction lines, it is
important to ensure that pressure does not drop below the vapor pressure and that the liquid does not start to
boil. It is also important to ensure that the gases that occur naturally in many liquids do not outgas. Such effects
can be prevented when system pressure is sufficiently high.
Therefore, the following locations should be preferred for installation:
• Downstream from pumps (no danger of vacuum)
• At the lowest point in a vertical pipe
Operating conditions: Environment
Ambient temperature range Sensor, transmitter:

• Standard: –20 to +60 °C (–4 to +140 °F)
• Optional: –40 to +60 °C (–40 to +140 °F)
! Note!
• Install the device at a shady location. Avoid direct sunlight, particularly in warm climatic regions.
• At ambient temperatures below –20 °C (–4 °F) the readability of the display may be impaired.
Storage temperature –40 to +80 °C (–40 to +175 °F), preferably +20 °C (+68 °F)
Degree of protection Standard: IP 67 (NEMA 4X) for transmitter and sensor
Shock resistance According to IEC 68-2-31
Vibration resistance Acceleration up to 1 g, 10 to 150 Hz, following IEC 68-2-6
Electromagnetic compatibility As per IEC/EN 61326 and NAMUR recommendation NE 21

(EMC)
20 Endress+Hauser
Operating conditions: Process
Fluid temperature range Sensor

–40 to +140 °C (–40 to +284 °F)
Fluid density range 0 to 5000 kg/m³ (0 to +312 lb/cf)
Fluid pressure range (nominal Flanges

pressure)
• according to DIN PN 40 to 100
• according to ASME B16.5 Cl 150, Cl 300, Cl 600
• JIS 10K, 20K, 40K, 63K
Secondary containment
The sensor Promass E has no secondary containment.
Rupture disk in the sensor The sensor housing protects the inner electronics and mechanics and is filled with dry nitrogen. The housing
housing (optional) of this sensor does not fulfill any additional secondary containment function. However, 15 bar (217.5 psi) can
be specified as a reference value for the pressure loading capacity.
For increased safety, a version with rupture disk (triggering pressure 10 to 15 bar / 145 to 217.5 psi) can be
used, which is available for order as a separate option.
Further information  ä 40.
Limiting flow See information in the "Measuring range" section  ä 6.

Select nominal diameter by optimizing between required flow range and permissible pressure loss. See the
"Measuring range" section for a list of maximum possible full scale values.
• The minimum recommended full scale value is approx. 1/20 of the max. full scale value.
• In most applications, 20 to 50% of the maximum full scale value can be considered ideal
• Select a lower full scale value for abrasive substances such as fluids with entrained solids
(flow velocity <1 m/s (<3 ft/s)).
• For gas measurement the following rules apply:
– Flow velocity in the measuring tubes should not be more than half the sonic velocity (0.5 Mach).
– The maximum mass flow depends on the density of the gas: formula  ä 6
Pressure loss Pressure loss depends on the fluid properties and on the flow rate. The following formulae can be used to
approximately calculate the pressure loss:
2·g
Reynolds number Re =
p·d·n·r
a0004623
Dp = K · n ·r
0.25 1.85 –0.86
Re  23001) ·g
a0004626
K2 · n · g
0.25 2
Re < 2300 Dp = K1 · n · g +
r
a0004628
p = pressure loss [mbar]  = fluid density [kg/m3]

 = kinematic viscosity [m2/s] d = inside diameter of measuring tubes [m]
g = mass flow [kg/s] K to K2 = constants (depending on nominal diameter)
1)
To compute the pressure loss for gases, always use the formula for Re  2300.
Endress+Hauser 21
Pressure loss coefficients
DN d[m] K K1 K2
8 5.35 · 10–3 5.70 · 107 7.91 · 107 2.10 · 107
15 8.30 · 10–3 7.62 · 106 1.73 · 107 2.13 · 106
25 12.00 · 10–3 1.89 · 106 4.66 · 106 6.11 · 105
40 17.60 · 10–3 4.42 · 105 1.35 · 106 1.38 · 105
50 26.00 · 10–3 8.54 · 104 4.02 · 105 2.31 · 104
80 40.50 · 10–3 1.44 · 104 5.00 · 105 2.30 · 104
[mbar]
10000
DN 40
DN 25
DN 15 DN 50
DN 8
DN 80
1000
100
10
0.1
0.001 0.01 0.1 1 10 100 1000 [t/h]
a0004606
Pressure loss diagram for water
Pressure loss (US units)

Pressure loss is dependent on fluid properties nominal diameter. Consult Endress+Hauser for Applicator PC
software to determine pressure loss in US units. All important instrument data is contained in the Applicator
software program in order to optimize the design of measuring system. The software is used for following
calculations:
• Nominal diameter of the sensor with fluid characteristics such as viscosity, density, etc.
• Pressure loss downstream of the measuring point.
• Converting mass flow to volume flow, etc.
• Simultaneous display of various meter size.
• Determining measuring ranges.
The Applicator runs on any IBM compatible PC with windows.
22 Endress+Hauser
Mechanical construction
Design, dimensions Dimensions:
Field housing compact version, powder-coated die-cast aluminum  ä 24
Field housing compact version (II2G/Zone 1), powder-coated die-cast aluminum  ä 25
Transmitter connection housing remote version (II2G/Zone 1)  ä 26
Transmitter remote version, wall-mount housing (non hazardous area and II3G / zone 2)  ä 27
Sensor remote version, connection housing  ä 28
Process connections in SI units
Flange connections EN (DIN)  ä 29
Flange connections ASME B16.5  ä 30
Flange connections JIS  ä 31
VCO connections  ä 32
Tri-Clamp  ä 33
DIN 11851 (threaded hygienic connection)  ä 34
DIN 11864-1 Form A (threaded hygienic connection)  ä 34
DIN 11864-2 Form A (flat flange with groove)  ä 35
ISO 2853 (threaded hygienic connection)  ä 36
SMS 1145 (threaded hygienic connection)  ä 36
Flange connections ASME B16.5  ä 37
VCO connections  ä 38
Tri-Clamp  ä 39
SMS 1145 (threaded hygienic connection)  ä 40
Rupture disc  ä 40
Endress+Hauser 23
Field housing compact version, powder-coated die-cast aluminum
A B
A* C
E
E
G
F
di L
A0007638
Dimensions SI units
DN A A* B C D E F G L di
1) 1)
8 227 207 187 168 160 224 93 317
15 227 207 187 168 160 226 105 331 1) 1)
25 227 207 187 168 160 231 106 337 1) 1)
1) 1)
40 227 207 187 168 160 237 121 358
50 227 207 187 168 160 253 170 423 1) 1)
80 227 207 187 168 160 282 205 487 1) 1)
1)
dependent on respective process connection
* Blind version (without local display)
All dimensions in [mm]
Dimensions in US units
3/8" 9.08 8.28 7.48 6.72 6.40 8.82 3.66 12.48 2) 2)
2) 2)
½" 9.08 8.28 7.48 6.72 6.40 8.90 4.13 13.03
1" 9.08 8.28 7.48 6.72 6.40 9.09 4.17 13.27 2) 2)
1½" 9.08 8.28 7.48 6.72 6.40 9.33 4.76 14.09 2) 2)
2) 2)
2" 9.08 8.28 7.48 6.72 6.40 9.96 6.69 16.65
3" 9.08 8.28 7.48 6.72 6.40 11.10 8.07 19.17 2) 2)
1)
All dimensions in [inch]
24 Endress+Hauser
Field housing compact version (II2G/Zone 1), powder-coated die-cast aluminum
A B
A* C
e r Sp annu
ht unt ng
Nic öffnen
Nicht-eigensichere
Ke ircuit s are aliv ile

Stromkreise durch
ove r tight wh
e
IP40-Abdeckung geschützt
Non-intrinsically safe
D
circuits Ip40 protected
ep c
Boucles de courant
c
sans sécurité intrinsèque
protégées par Ip40
E
sou s nsion l Ne
pas o t e pparei
uvrir l’a
G
F
di L
A0015135
Dimensions SI units
1) 1)
8 240 217 206 186 178 242 93 335
15 240 217 206 186 178 244 105 349 1) 1)
25 240 217 206 186 178 249 106 355 1) 1)
1) 1)
40 240 217 206 186 178 255 121 376
50 240 217 206 186 178 271 170 441 1) 1)
80 240 217 206 186 178 300 205 505 1) 1)
1)
3/8" 9,45 8,54 8,11 7,32 7,01 9,52 3,66 13,18 1) 1)
1) 1)
½" 9,45 8,54 8,11 7,32 7,01 9,60 4,13 13,73
1" 9,45 8,54 8,11 7,32 7,01 9,79 4,17 13,97 1) 1)
1½" 9,45 8,54 8,11 7,32 7,01 10,03 4,76 14,79 1) 1)
1) 1)
2" 9,45 8,54 8,11 7,32 7,01 10.66 6,69 17,35
3" 9,45 8,54 8,11 7,32 7,01 11,80 8,07 19,87 1) 1)
1)
Endress+Hauser 25
Transmitter connection housing remote version (II2G/Zone 1)
A
A*
B C
B* D
e r Sp annu
ht unt ng
Nic öffnen
Nicht-eigensichere
Ke ircuit s a re aliv ile
Kee ircuits are ali hile

Stromkreise durch
ove r tight wh
e
c
IP40-Abdeckung geschützt
p cover tight w
Non-intrinsically safe
circuits Ip40 protected
E
ep c
Esc
Boucles de courant
c
– +
ve
E
sans sécurité intrinsèque
protégées par Ip40
sou s nsion l Ne
pas o t e pparei
uvrir l’a
M
L
J
K
F
G
a0002128
Dimensions in SI units
A A* B B* C D E F G H J K L M
8.6
265 242 240 217 206 186 178 100 130 100 144 170 348
(M8)

A A* B B* C D E F G H J K L M

10.4 9.53 9.45 8.54 8.11 7.32 7.01 3.94 5.12 3.94 5.67 6.69 13.7
(M8)

26 Endress+Hauser
Transmitter remote version, wall-mount housing (non hazardous area and II3G / zone 2)
D
Esc
- + E
B
C
F G
A E
H J K J
N
S S
M
R
L
O
P Q P
a0001150
A B C D E F G H J
215 250 90.5 159.5 135 90 45 >50 81
K L M N O P Q R S
53 95 53 102 81.5 11.5 192 8 × M5 20
A B C D E F G H J
8.46 9.84 3.56 6.27 5.31 3.54 1.77 >1.97 3.18
K L M N O P Q R S
2.08 3.74 2.08 4.01 3.20 0.45 7.55 8 × M5 0.79
Endress+Hauser 27
Sensor remote version, connection housing
C
a0007637
DN A B C
8 129 102 166
15 129 102 168
25 129 102 173
40 129 102 179
50 129 102 195
80 129 102 224
DN A B C
3/8" 5.08 4.02 6.54
½" 5.08 4.02 6.61
1" 5.08 4.02 6.81
1½" 5.08 4.02 7.05
2" 5.08 4.02 7.68
3" 5.08 4.02 8.82
28 Endress+Hauser
Flange connections EN (DIN), ASME B16.5, JIS
LK
G
U
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007640-ae
Flange connections EN (DIN)
Flange according to EN 1092-1 (DIN 2501 / DIN 2512N 1) / PN 40: 1.4404/316L
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 μm
DN G L N S LK U di
8 95 232 4 × Ø14 16 65 17.3 5.35
15 95 279/5102) 4 × Ø14 16 65 17.3 8.30

2)
25 115 329/600 4 × Ø14 18 85 28.5 12.0
40 150 445 4 × Ø18 18 110 43.1 17.6
50 165 556/7152) 4 × Ø18 20 125 54.5 26.0

2)
80 200 610/915 8 × Ø18 24 160 82.5 40.5
1)Flange with groove according to EN 1092-1 Form D (DIN 2512N) available
2)Installation length according to NAMUR recommendation NE 132 optionally available
Flange according to EN 1092-1 (DIN 2501) / PN 40 (with DN 25-flanges): 1.4404/316L
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 μm
DN G L N S LK U di
8 115 329 4 × Ø14 18 85 28.5 5.35
15 115 329 4 × Ø14 18 85 28.5 8.30
Flange according to EN 1092-1 (DIN 2501 / DIN 2512N 1)) / PN 63: 1.4404/316L
Surface roughness (flange): EN 1092-1 Form B2 (DIN 2526 Form E), Ra 0.8 to 3.2 μm
DN G L N S LK U di
50 180 565 4 × Ø22 26 135 54,5 26,0
80 215 650 8 × Ø22 28 170 81,7 40,5

1)
Flange with groove according to EN 1092-1 Form D (DIN 2512N) available
Endress+Hauser 29
Flange EN 1092-1 (DIN 2501 / DIN 2512N 1)) / PN 100: 1.4404/316L
Surface roughness (flange): EN 1092-1 Form B2 (DIN 2526 Form E), Ra 0.8 to 3.2 μm
DN G L N S LK U di
8 105 261 4 × Ø14 20 75 17.3 5.35
15 105 295 4 × Ø14 20 75 17.3 8.30
25 140 360 4 × Ø18 24 100 28.5 12.0
40 170 486 4 × Ø22 26 125 42.5 17.6
50 195 581 4 × Ø26 28 145 53.9 26.0
80 230 660 8 × Ø26 32 180 80.9 40.5

1)
Flange with groove to EN 1092-1 Form D (DIN 2512N) available
Flange connections ASME B16.5
Flange according to ASME B16.5 / Cl 150: 1.4404/316L
DN G L N S LK U di
8 88.9 232 4 × Ø15.7 11.2 60.5 15.7 5.35
15 88.9 279 4 × Ø15.7 11.2 60.5 15.7 8.30
25 108.0 329 4 × Ø15.7 14.2 79.2 26.7 12.0
40 127.0 445 4 × Ø15.7 17.5 98.6 40.9 17.6
50 152.4 556 4 × Ø19.1 19.1 120.7 52.6 26.0
80 190.5 610 4 × Ø19.1 23.9 152.4 78.0 40.5
DN G L N S LK U di
8 95.2 232 4 × Ø15.7 14.2 66.5 15.7 5.35
15 95.2 279 4 × Ø15.7 14.2 66.5 15.7 8.30
25 123.9 329 4 × Ø19.0 17.5 88.9 26.7 12.0
40 155.4 445 4 × Ø22.3 20.6 114.3 40.9 17.6
50 165.1 556 8 × Ø19.0 22.3 127.0 52.6 26.0
80 209.5 610 8 × Ø22.3 28.4 168.1 78.0 40.5
DN G L N S LK U di
8 95.3 261 4 × Ø15.7 20.6 66.5 13.9 5.35
15 95.3 295 4 × Ø15.7 20.6 66.5 13.9 8.30
25 124.0 380 4 × Ø19.1 23.9 88.9 24.3 12.0
40 155.4 496 4 × Ø22.4 28.7 114.3 38.1 17.6
50 165.1 583 8 × Ø19.1 31.8 127.0 49.2 26.0
80 209.6 672 8 × Ø22.4 38.2 168.1 73.7 40.5
30 Endress+Hauser
Flange connections JIS
Flange JIS B2220 / 10K: SUS 316L
DN G L N S LK U di
50 155 556 4 × Ø19 16 120 50 26.0
80 185 605 8 × Ø19 18 150 80 40.5
DN G L N S LK U di
8 95 232 4 × Ø15 14 70 15 5.35
15 95 279 4 × Ø15 14 70 15 8.30
25 125 329 4 × Ø19 16 90 25 12.0
40 140 445 4 × Ø19 18 105 40 17.6
50 155 556 8 × Ø19 18 120 50 26.0
80 200 605 8 × Ø23 22 160 80 40.5
DN G L N S LK U di
8 115 261 4 × Ø19 20 80 15 5.35
15 115 300 4 × Ø19 20 80 15 8.30
25 130 375 4 × Ø19 22 95 25 12.0
40 160 496 4 × Ø23 24 120 38 17.6
50 165 601 8 × Ø19 26 130 50 26.0
80 210 662 8 × Ø23 32 170 75 40.5
DN G L N S LK U di
8 120 282 4 × Ø19 23 85 12 5.35
15 120 315 4 × Ø19 23 85 12 8.30
25 140 383 4 × Ø23 27 100 22 12.0
40 175 515 4 × Ø25 32 130 35 17.6
50 185 616 8 × Ø23 34 145 48 26.0
80 230 687 8 × Ø25 40 185 73 40.5
Endress+Hauser 31
VCO connections
U
G
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007641-ae
VCO connections: 1.4404/316L
DN G L U di
8 1" AF 252 10.2 5.35
15 1½" AF 305 15.7 8.30
32 Endress+Hauser
Tri-Clamp
G
U
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007643-ae
1", 1½", 2" -Tri-Clamp: 1.4404/316L
DN Clamp G L U di
8 1" 50.4 229 22.1 5.35
15 1" 50.4 273 22.1 8.30
25 1" 50.4 324 22.1 12.0
40 1½" 50.4 456 34.8 17.6
50 2" 63.9 562 47.5 26.0
80 3" 90.9 672 72.9 40.5
3A version also available (Ra  0.8 μm/150 grit.)

½"-Tri-Clamp: 1.4404/316L
DN Clamp G L U di
8 ½" 25.0 229 9.5 5.35
15 ½" 25.0 273 9.5 8.30

Endress+Hauser 33
DIN 11851 (threaded hygienic connection)
G
U
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007644-ae
Threaded hygienic connection DIN 11851: 1.4404/316L
DN G L U di
8 Rd 34 × 1/8" 229 16 5.35
15 Rd 34 × 1/8" 273 16 8.30
25 Rd 52 × 1/6" 324 26 12.0
40 Rd 65 × 1/6" 456 38 17.6
50 Rd 78 × 1/6" 562 50 26.0
80 Rd 110 × 1/4" 672 81 40.5
3A version also available (Ra  0.8 μm/150 grit.); All dimensions in [mm]
DIN 11864-1 Form A (threaded hygienic connection)
E
G
U
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007649-ae
Threaded hygienic connection DIN 11864-1 Form A: 1.4404/316L
DN G L U di
8 Rd 28 × 1/8" 229 10 5.35
15 Rd 34 × 1/8" 273 16 8.30
25 Rd 52 × 1/6" 324 26 12.00
40 Rd 65 × 1/6" 456 38 17.60
50 Rd 78 × 1/6" 562 50 26.00
80 Rd 110 × 1/4" 672 81 40.5
34 Endress+Hauser
DIN 11864-2 Form A (flat flange with groove)
LK
G
U
+1.5 (+0.06)
di L –2.0 (–0.08)
S
mm (inch)
a0007649-ae
DIN 11864-2 Form A (flat flange with groove): 1.4404/316L
DN G L N S LK U di
8 54 249 4 × Ø9 10 37 10 5.35
15 59 293 4 × Ø9 10 42 16 8.30
25 70 344 4 × Ø9 10 53 26 12.0
40 82 456 4 × Ø9 10 65 38 17.6
50 94 562 4 × Ø9 10 77 50 26.0
80 133 672 8 × Ø11 12 112 81 40.5

Endress+Hauser 35
ISO 2853 (threaded hygienic connection)
G
U
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007651-ae
Threaded hygienic connection ISO 2853: 1.4404/316L
DN G L U di
8 37.13 229 22.6 5.35
15 37.13 273 22.6 8.30
25 37.13 324 22.6 12.0
40 50.68 456 35.6 17.6
50 64.16 562 48.6 26.0
80 91.19 672 72.9 40.5

1)Max. thread diameter to ISO 2853 Annex A; 3A version also available (Ra  0.8 μm/150 grit.)
SMS 1145 (threaded hygienic connection)
E
G
U
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007653-ae
Threaded hygienic connection SMS 1145: 1.4404/316L
DN G L U di
8 Rd 40 × 1/6" 229 22.5 5.35
15 Rd 40 × 1/6" 273 22.5 8.30
25 Rd 40 × 1/6" 324 22.5 12.0
40 Rd 60 × 1/6" 456 35.5 17.6
50 Rd 70 × 1/6" 562 48.5 26.0
80 Rd 98 × 1/6" 672 72.9 40.5
36 Endress+Hauser
Process connections in US units
Flange connections ASME B16.5
LK
G
U
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007640-ae
DN G L N S LK U di
3/8" 3.50 9.13 4 × Ø0.62 0.44 2.38 0.62 0.21
½" 3.50 10.98 4 × Ø0.62 0.44 2.38 0.62 0.33
1" 4.25 12.95 4 × Ø0.62 0.56 3.12 1.05 0.47
1½" 5.00 17.52 4 × Ø0.62 0.69 3.88 1.61 0.69
2" 6.00 21.89 4 × Ø0.75 0.75 4.75 2.07 1.02
3" 7.50 24.02 4 × Ø0.75 0.94 6.00 3.07 1.59
DN G L N S LK U di
3/8" 3.75 9.13 4 × Ø0.62 0.56 2.62 0.62 0.21
½" 3.75 10.98 4 × Ø0.62 0.56 2.62 0.62 0.33
1" 4.88 12.95 4 × Ø0.75 0.69 3.50 1.05 0.47
1½" 6.12 17.52 4 × Ø0.88 0.81 4.50 1.61 0.69
2" 6.50 21.89 4 × Ø0.75 0.88 5.00 2.07 1.02
3" 8.25 24.02 8 × Ø0.88 1.12 6.62 3.07 1.59
DN G L N S LK U di
3/8" 3.75 10.28 4 × Ø0.62 0.81 2.62 0.55 0.21
½" 3.75 11.61 4 × Ø0.62 0.81 2.62 0.55 0.33
1" 4.88 14.96 4 × Ø0.75 0.94 3.50 0.96 0.47
1½" 6.12 19.53 4 × Ø0.88 1.13 4.50 1.50 0.69
2" 6.50 22.95 4 × Ø0.75 1.25 5.00 1.94 1.02
3" 8.25 24.46 8 × Ø0.88 1.50 6.62 2.90 1.59
Endress+Hauser 37
VCO connections
U
G
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007641-ae
VCO connections: 1.4404/316L
DN G L U di
3/8" 1" AF 9.92 0.40 0.21
½" 1½" AF 12.01 0.62 0.33
38 Endress+Hauser
Tri-Clamp
G
U
E
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007643-ae
1", 1½", 2" -Tri-Clamp: 1.4404/316L
DN Clamp G L U di
3/8" 1" 1.98 9.02 0.87 0.21
½" 1" 1.98 10.75 0.87 0.33
1" 1" 1.98 12.76 0.87 0.47
1½" 1½" 1.98 17.95 1.37 0.69
2" 2" 2.52 22.13 1.87 1.02
3" 3" 3.58 26.46 2.87 1.59
3A version also available (Ra  30 μin/150 grit.)

½"-Tri-Clamp: 1.4404/316L
DN Clamp G L U di
3/8" ½" 0.98 9.02 0.37 0.21
½" ½" 0.98 10.75 0.37 0.33
3A version also available (Ra  30 μin/150 grit.)

Endress+Hauser 39
SMS 1145 (threaded hygienic connection)
G
U
+1.5 (+0.06)
di L –2.0 (–0.08) mm (inch)
a0007653-ae
Threaded hygienic connection SMS 1145: 1.4404/316L
DN G L U di
3/8" Rd 40 × 1/6" 9.02 0.89 0.21
½" Rd 40 × 1/6" 10.75 0.89 0.33
1" Rd 40 × 1/6" 12.76 0.89 0.47
1½" Rd 60 × 1/6" 17.95 1.40 0.69
2" Rd 70 × 1/6" 22.13 1.91 1.02
3" Rd 98 × 1/6" 26.46 2.87 1.59
3A version also available (Ra  30 μin/150 grit.); All dimensions in [inch]
Rupture disc Sensor housings with integrated rupture disks are optionally available.
# Warning!
• Make sure that the function and operation of the rupture disk is not impeded through the installation.
Triggering overpressure in the housing as stated on the indication label. Take adequate precautions to ensure
that no damage occurs, and risk to human life is ruled out, if the rupture disk is triggered.
Rupture disk: Burst pressure 10 to 15 bar (145 to 217.5 psi).
• It is not permitted to open the connections or remove the rupture disk.
" Caution!
Rupture disks can not be combined with separately available heating jacket.
! Note!
• Please note the indication labels.
RUPTURE DISK
12,5 BAR +/-20%@20°C
A0007823
Indication label for the rupture disk
The position of the rupture disk is indicated by an adhesive label on top of the disk. If the rupture disk is
triggered, the adhesive label is damaged and can thus be visually monitored.
40 Endress+Hauser
Weight • Compact version: see table below

• Remote version
– Sensor: see table below
– Wall-mount housing: 5 kg (11 lb)
Weight in SI units
DN [mm] 8 15 25 40 50 80
Compact version 8 8 10 15 22 31
Remote version (sensor) 6 6 8 13 20 29
All values (weight) refer to devices with EN/DIN PN 40 flanges.

Weight information in [kg]
Weight in US units
DN [inch] 3/8" ½" 1" 1½" 2" 3"
Compact version 18 18 22 33 49 69
Remote version (sensor) 13 13 18 29 44 64
All values (weight) refer to devices with EN/DIN PN 40 flanges.

Weight information in [lb]
Materials Transmitter housing

Compact version
• Powder coated die-cast aluminum
• Window material: glass
Remote version
• Remote field housing: powder-coated die-cast aluminum
• Wall-mount housing: powder coated die-cast aluminum
• Window material: glass
Sensor housing / containment

• Acid and alkali-resistant outer surface
• Stainless steel 1.4301/304
Connection housing, sensor (remote version)

Stainless steel 1.4301/304
Process connections
• Stainless steel 1.4404/316L
– Flanges according to EN 1092-1 (DIN 2501) and according to ASME B16.5
– DIN 11864-2 Form A (flat flange with groove)
– Threaded hygienic connection: DIN 11851, SMS 1145, ISO 2853, DIN 11864-1 Form A
– VCO connections
• Stainless steel SUS 316L
– Flanges to JIS B2220
Measuring tubes
• Stainless steel EN 1.4539 / ASTM 904L
• Finish quality: Ramax  0.8 μm/150 grit (30 μin/150 grit)
Seals
Welded process connections without internal seals
Endress+Hauser 41
Material load curves
# Warning!
The following material load curves refer to the entire sensor and not just the process connection.
Flange connection according to EN 1092-1 (DIN 2501)

Flange material: 1.4404/316L
[psi] [bar]
1500
100
1400 PN 100
1300 90
1200
80
1100
1000 70
900 60 PN 63
800
50
700
600 40
PN 40
500
30
400
300 20
200
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
a0006904-ae
Flange connection according to ASME B16.5

[psi] [bar]
1500
100
1400
1300 90
1200
80 Class 600
1100
1000 70
900 60
800
50
700
600 40
Class 300
500
30
400
300 20
200
10 Class 150
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
a0006905-ae
42 Endress+Hauser
Flange connection to JIS B2220

Flange material: SUS 316L
[psi] [bar]
1000 70
900 60 63K
800
50
700
600 40
40K
500
30
400
300 20
20K
200
10
100 10K
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0006906-ae
VCO process connection

[psi] [bar]
1500
100
1400 PN 100
1300 90
1200
80
1100
1000 70
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
[°F]
-80 -40 0 40 80 120 160 200 240 280 320 360 400
a0006908-ae
Tri-Clamp process connection

The Clamp connections are suited up to a maximum pressure of 16 bar (232 psi). Please observe the operating
limits of the clamp and seal used as they could be under 16 bar (232 psi). The clamp and the seal are not
included in the scope of supply.
Process connection to DIN 11851

Connection material: 1.4404/316L
[psi] [bar]
50
700
600 40
DN 8…40
500
30
400
300 20 DN 50…80
200
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0006909
DIN 11851 allows for applications up to +140 °C (+284 °F) if suitable sealing materials are used. Please take this into
account when selecting seals and counterparts as these components can limit the pressure and temperature range.
Endress+Hauser 43
Process connection to SMS 1145

[psi] [bar]
500
30
400
300 20
200 PN 16
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0012947
SMS 1145 allows for applications up to 6 bar (87 psi) if suitable sealing materials are used. Please take this into account
when selecting seals and counterparts as these components can limit the pressure and temperature range.
DIN 11864-1 Form A (threaded hygienic connection)

[psi] [bar]
50
700
600 40
DN 8...40
500
30
400
300 20 DN 50…80
200
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0006910-ae
Flange connection to DIN 11864-2 Form A (flat flange with groove)

[psi] [bar]
600 40
500
30 DN 8...40
400
300 20
200 DN 50…80
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0006911-ae
44 Endress+Hauser
Threaded hygienic connection to ISO 2853

[psi] [bar]
30
400
300 20
200
10
100
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0006912-ae
Process connections Welded process connections

• Flanges according to EN 1092-1 (DIN 2501), according to ASME B16.5, JIS B2220, VCO connections
• Sanitary connections: Tri-Clamp, threaded hygienic connections (DIN 11851, SMS 1145, ISO 2853,
DIN 11864-1), DIN 11864-2 Form A (flat flange with groove)
Human interface
Display elements • Liquid-crystal display: backlit, two lines (Promass 80) or four lines (Promass 83) with 16 characters per line
• Selectable display of different measured values and status variables
• At ambient temperatures below –20 °C (–4 °F) the readability of the display may be impaired.
Operating elements Promass 80

• Local operation with three keys (S/O/F)
• Quick Setup menus for straightforward commissioning
Promass 83
• Local operation with three optical keys (S/O/F)
• Application-specific Quick Setup menus for straightforward commissioning
Language groups Language groups available for operation in different countries:

• Western Europe and America (WEA):
English, German, Spanish, Italian, French, Dutch and Portuguese
• Eastern Europe/Scandinavia (EES):
English, Russian, Polish, Norwegian, Finnish, Swedish and Czech
• South and Eastern Asia (SEA):
English, Japanese, Indonesian
Only Promass 83
• China (CN):
English, Chinese
The language group is changed using the "FieldCare" operating program.
Remote operation Promass 80

Remote operation via HART, PROFIBUS PA
Promass 83
Remote operation via HART, PROFIBUS DP/PA, FOUNDATION fieldbus, MODBUS RS485
Endress+Hauser 45
Certificates and approvals

CE mark The measuring system is in conformity with the statutory requirements of the EC Directives.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
C-Tick symbol The measuring system complies with the EMC requirements of the "Australian Communications and Media
Authority (ACMA)"
Ex approval Information about currently available Ex versions (ATEX, FM, CSA, IECEx, NEPSI etc.) can be supplied by your
Endress+Hauser Sales Center on request. All information relevant to explosion protection is available in
separate Ex documents that you can order as necessary.
Hygienic compatibility 3A approval
FOUNDATION Fieldbus The flow device has successfully passed all the test procedures carried out and is certified and registered by the
certification Fieldbus Foundation. The device thus meets all the requirements of the following specifications:
• Certified to FOUNDATION Fieldbus Specification
• The device meets all the specifications of the FOUNDATION Fieldbus H1.
• Interoperability Test Kit (ITK), revision status 5.01 (device certification number: on request)
• The device can also be operated with certified devices of other manufacturers
• Physical Layer Conformance Test of the Fieldbus Foundation
PROFIBUS DP/PA The flow device has successfully passed all the test procedures carried out and is certified and registered by the
certification PNO (PROFIBUS User Organization). The device thus meets all the requirements of the following
specifications:
• Certified in accordance with PROFIBUS Profile Version 3.0 (device certification number: available on
request)
• The device can also be operated with certified devices of other manufacturers (interoperability)
MODBUS certification The measuring device meets all the requirements of the MODBUS/TCP conformity test and has the
"MODBUS/TCP Conformance Test Policy, Version 2.0". The measuring device has successfully passed all the
test procedures carried out and is certified by the "MODBUS/TCP Conformance Test Laboratory" of the
University of Michigan.
Other standards and • EN 60529

guidelines Degrees of protection by housing (IP code)
• EN 61010-1
Protection Measures for Electrical Equipment for Measurement, Control, Regulation and Laboratory
Procedures.
• IEC/EN 61326
"Emission in accordance with Class A requirements". Electromagnetic compatibility (EMC requirements)
• NAMUR NE 21
Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment.
• NAMUR NE 43
Standardization of the signal level for the breakdown information of digital transmitters with analog output
signal.
• NAMUR NE 53
Software of field devices and signal-processing devices with digital electronics
Pressure Equipment Directive The measuring devices can be ordered with or without PED (Pressure Equipment Directive). If a device with
PED is required, this must be ordered explicitly. For devices with nominal diameters less than or equal to DN
25 (1"), this is neither possible nor necessary.
• With the identification PED/G1/III on the sensor nameplate, Endress+Hauser confirms conformity with the
"Basic safety requirements" of Appendix I of the Pressure Equipment Directive 97/23/EC.
• Devices with this identification (with PED) are suitable for the following types of fluid:
- Fluids of Group 1 and 2 with a steam pressure of greater or less than 0.5 bar (7.3 psi)
- Unstable gases
46 Endress+Hauser
• Devices without this identification (without PED) are designed and manufactured according to good
engineering practice. They correspond to the requirements of Art. 3, Section 3 of the Pressure Equipment
Directive 97/23/EC. Their application is illustrated in Diagrams 6 to 9 in Appendix II of the Pressure
Equipment Directive 97/23/EC.
Functional safety SIL -2: accordance IEC 61508/IEC 61511-1 (FDIS)

"4–20 mA HART" output according to the following order code:
Promass 80
Promass80***-************A
Promass80***-************D
Promass80***-************S
Promass80***-************T
Promass80***-************8
Promass 83
Promass83***-************A Promass83***-************M Promass83***-************Ø
Promass83***-************B Promass83***-************R Promass83***-************2
Promass83***-************C Promass83***-************S Promass83***-************3
Promass83***-************D Promass83***-************T Promass83***-************4
Promass83***-************E Promass83***-************U Promass83***-************5
Promass83***-************L Promass83***-************W Promass83***-************6
Ordering Information
The Endress+Hauser service organization can provide detailed ordering information and information on the
order codes upon request.
Accessories
Various accessories, which can be ordered separately from Endress+Hauser, are available for the transmitter
and the sensor.
Documentation
• Flow measuring technology (FA005D)
• Technical Information
– Promass 80A, 83A (T054D)
– Promass 80F, 83F (TI101D)
– Promass 80H, 83H (TI074D
– Promass 80I, 83I (TI075D)
– Promass 80P, 83P (TI078D)
– Promass 80S, 83S (TI076D)
• Operating Instructions/Description of Device Functions
– Promass 80 HART (BA057D/BA058D)
– Promass 80 PROFIBUS PA (BA072D/BA073D)
– Promass 83 HART (BA059D/BA060D)
– Promass 83 FOUNDATION Fieldbus (BA065D/BA066D)
– Promass 83 PROFIBUS DP/PA(BA063D/BA064D)
– Promass 83 MODBUS (BA107D/BA108D)
• Supplementary documentation on Ex-ratings: ATEX, FM, CSA, IECEx NEPSI
• Functional safety manual Promass 80, 83 (SD077D)
Endress+Hauser 47
Registered trademarks
TRI-CLAMP ®
Registered trademark of Ladish & Co., Inc., Kenosha, WI, USA
HART®
Registered trademark of HART Communication Foundation, Austin, TX, USA
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
FOUNDATION™ Fieldbus
Registered trademark of the Fieldbus FOUNDATION, Austin, USA
MODBUS®
Registered trademark of the MODBUS Organization
HistoROM™, S-DAT®, T-DAT™, F-CHIP®, Fieldcheck®, FieldCare®, Applicator®
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH
48 Endress+Hauser
Endress+Hauser 49
50 Endress+Hauser
Endress+Hauser 51
Instruments International
Endress+Hauser
Instruments International AG
Kaegenstrasse 2
4153 Reinach
Switzerland
Tel. +41 61 715 81 00

Fax +41 61 715 25 00
www.endress.com
info@ii.endress.com
TI00061D/06/EN/13.11
71129459
FM+SGML6.0 ProMoDo

Promass 80E - TI00061DEN

Uploaded by

Copyright:

Available Formats

Promass 80E - TI00061DEN

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Promass 80E - TI00061DEN

Uploaded by

Copyright:

Available Formats

Technical Information

Proline Promass 80E, 83E

Application Your benefits

Function and system design. . . . . . . . . . . . . . . . . . . . . 3 Limiting flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Performance characteristics. . . . . . . . . . . . . . . . . . . . 14 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . 47

Operating conditions: Environment. . . . . . . . . . . . . . 20

Operating conditions: Process . . . . . . . . . . . . . . . . . . 21

Function and system design

Promass 80 • Two-line liquid-crystal display

Promass 83 • Four-line liquid-crystal display

E • General purpose sensor, ideal replacement for volumetric Documentation No.

Other sensors can be found in the separate documentation

A • Single-tube system for highly accurate measurement of Documentation No.

F • Universal sensor for fluid temperatures Documentation No.

F (High-temperature) • Universal high-temperature sensor for fluid temperatures

I • Straight single-tube instrument. Minimal shear stress on Documentation No.

P • Single bent tube, minimal shear stress on fluid. Documentation No.

S • Single bent tube. Documentation No.

Measuring range Measuring ranges for liquids

DN Range for full scale values (liquids) gmin(F) to gmax(F)

[mm] [inch] [kg/h] [lb/min]

8 3/8" 0 to 2000 0 to 73.5

15 ½" 0 to 6500 0 to 238

25 1" 0 to 18000 0 to 660

40 1 ½" 0 to 45000 0 to 1650

50 2" 0 to 70000 0 to 2570

80 3" 0 to 180000 0 to 6600

Measuring ranges for gases

Here, gmax(G) can never be greater than gmax(F)

Calculation example for gas:

Recommended full scale values

Input signal Status input (auxiliary input)

Status input (auxiliary input) with PROFIBUS DP

Status input (auxiliary input) with MODBUS RS485

Current input (only Promass 83)

FOUNDATION Fieldbus interface

Signal on alarm Current output

Status output (Promass 80)

Relay output (Promass 83)

Load see "Output signal"

Switching output Status output (Promass 80)

Relay output (Promass 83)

HART* PROFIBUS PA*

PROFIBUS DP* PROFIBUS DP**

Connecting the transmitter, cable cross-section: max. 2.5 mm2

Electrical connection, Promass 80

80***-***********A - - Frequency output Current output, HART

Frequency output Current output Ex i

Frequency output Current output Ex i

Terminal No. (inputs/outputs)

Fixed communication boards (permanent assignment)

83***-***********A - - Frequency output Current output, HART

83***-***********F - - - PROFIBUS PA, Ex i

83***-***********J - - +5V (ext. termination) PROFIBUS DP

83***-***********K - - - FOUNDATION Fieldbus

83***–***********Q - - Status input MODBUS RS485

83***-***********R - - Current output 2 Current output 1

Frequency output Current output Ex i

Frequency output Current output Ex i

80*-*********A - - Frequency output Current output, HART

83*-*********A - - Frequency output Current output, HART

83*-*********F - - - PROFIBUS PA, Ex i

83*-*********J - - +5V (ext. termination) PROFIBUS DP

83*-*********K - - - FOUNDATION Fieldbus

83*–*********Q - - Status input MODBUS RS485

83*-*********R - - Current output 2 Current output 1

83*-*********U - - Current output 2 Current output 1

83*-*********M Status input Freq.output 2 Frequency output 1 Current output, HART

83*–*********N Current output Frequency output Status input MODBUS RS485

83*–*********P Current output Frequency output Status input PROFIBUS DP

83*–*********V Relay output 2 Relay output 1 Status input PROFIBUS DP

83*–*********7 Relay output 2 Relay output 1 Status input MODBUS RS485