HTD 625 Manual

1. INTRODUCTION 3.
SPECIFICATIONS
The digital Humidity & Temperature Meter & Wet Bulb Display: Large 4-1/2 dual digital LCD display with backlight
Temperature Dew Point temperature has been designed to Sensor Type: A single chip relative humidity and temperature
combine the functions of Humidity Meter, Temperature Meter, multi sensor module comprising a calibrated
Wet Bulb Temperature and Dew point temperature. digital output.
Response Time: %RH:10S (90% at +25℃ still air)
It is an ideal Humidity & Temperature Meter Instrument with
Accuracy Note: Accuracy is specified for the following
scores of practical applications for laboratorial, industrial,
ambient temperature range: 64 to 82°F (18
Engineer and professional use.
to 28°C)
The Humidity & Temperature Meter is for use a humidity & Sampling Rate: 2.5 samples per second
temperature semiconductor sensor. This operation manual Polarity: Automatic, (-) negative polarity indication.
contains general information and specification. Over-range: “OL” mark indication.
2. FEATURES Low Battery Indication: The “ ” is displayed when the

battery voltage drops below the
z Fast Response Time %RH: 10S (90% at 25℃ still air) opera-ting level.
z High Accuracy
Operating Conditions: 32 to 104oF (0 to 40oC); < 80% RH
z Dew Point Temperature (-30℃~100℃/-22°F~199°F)
non-condensing
z Wet Bulb Temperature ( 0℃~80℃/32°F~176°F)
Storage Conditions: 14 to 140oF (-10 to 60oC); <80% RH
z Resolution 0.1%RH, 0. 1℃/0. 1°F
non-condensing
z Max Hold and Data Hold Function Non-Automatic /Auto Power Off: Firstly press humidity hold
z Micro Processor-based Design button, then press power button. After the full display appears,
z Dual Display Temperature & Humidity release both buttons. Icon“ ” will not show on the LCD. The
z Shutdown time digitally adjustable from 1 to 120 unit will not auto power off now.
z Backlight Directly press power on/off button. Meter automatically shuts
down after adjustment time inactivity (Sleep Mode).
Adjustable Shutdown Time: shutdown time digitally
adjustable from 1 to 120, Firstly press humidity max/min button,
then press power button. After the full display appears, release
1 2
both buttons. icon“ ” and the current shutdown time on the 4. PANEL DESCRIPTION
LCD. And then respectively press C and F key to upward and
downward.
Power: One standard 9V, NEDA1604 or 6F22 battery.
Dimensions/Wt.: 150mm*72mm*35 mm/210g
Humidity / Temperature Measurement Range:
Humidity: 0%~100%RH
Temperature: –30℃~ 100℃, -30℉~ 199℉
Resolution : 0.01% RH, 0.01℃/℉.
Humidity Accuracy: + 2%RH (at 25℃, 20%～80% RH). HOLD
MAX
MIN
+ 2.5%RH (at other ranges) 1
%RH
Note: The measuring range is from 0% to 100%, but above +
2
HOLD REL MAX MIN
80% and below 20% the deviation is not specified. BAT
CEM
DT-625
Air Temperature Accuracy: + 0.5℃/+ 0.9℉(at 25℃)
3
+ 0.8℃/+ 1.5℉(all other ranges)
7 4
TEMP. 5
6
3 4
① Temperature Display ⑬ Humidity / Air Temperature Probe: Humidity & and
② Humidity Display Temperature Semiconductor Sensor inside.
③ Power ON/OFF Button: Turn the meter power
ON/OFF.
5. HUMIDITY AND AIR TEMPERATURE
MEASU-REMENTS
④ ℃ : In the normal measurements to change the
DT625 from‘ºF’ to ‘ºC’. 1. Hold the probe in the area to be tested & allow
adequate time for readings to stabilize.
⑤ Dew Point Button: Dew Point Measurement.
2. Press ℉,℃, dew point, WBT Button to enter ℉,℃, dew
⑥ ’℉ : In the normal measurements to change the
point Wet Bulb Measurement
DT625 from‘ºC’ to ‘ºF’.
3. Read the Relative Humidity and Air Temperature, dew
⑦ Temperature MAX/ MIN Button: Press MAX/MIN point temperature wet bulb temperature.
button to enter MAX, MIN Recording mode (manual NOTE:
range only). Select the proper range before selecting
Do not immerse the probe in liquid; it is intended for use in air
MAX MIN to ensure that the MAX/MIN reading will only.
not exceed the testing range. Pressing the max/min Warning:
button once for Max or twice for Min function.
Don’t expose the sensor to direct sunlight.
⑧ WBT Button: Wet Bulb Measurement.
Don’t touch or manipulate the sensor.
⑨ Temperature HOLD Button: Press Hold Button to
6. BATTERY REPLACEMENT
enter hold function. The Temperature reading will be
held when Data Hold button is pressed. If the sign “ ” appears on the LCD display, it indicates
⑩ Backlight Button: To turn on or off backlight that the battery should be replaced. Open the battery case
and replace the exhausted battery with new battery. (1 x 9V
function.
battery NEDA 1604, 6F22 or equivalent).
⑪ Humidity HOLD Button
⑫ Humidity MAX/ MIN Button
5 6
TABLET OF CONTENTS
INSTRUCTION MANUAL TITLE
Humidity & Temperature Meter & 1. INTRODUCTION
Wet Bulb Temperature 2. FEATURES
Dew Point Temperature 3. SPECIFICATIONS
4. PANEL DESCRIPTION
5. HUMIDITY AND AIR TEMPERATURE
MEASUREMENTS
6. BATTERY REPLACEMENT
HOLD
MAX
MIN
%RH
HOLD REL MAX MIN BAT
CEM
DT-625
TEMP.
7 8

HTD 625 Manual

Uploaded by

Copyright:

Available Formats

HTD 625 Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HTD 625 Manual

Uploaded by

Copyright:

Available Formats

1. INTRODUCTION 3.

2. FEATURES Low Battery Indication: The “ ” is displayed when the

HOLD REL MAX MIN BAT

You might also like