Goldenmorning Electronic: Product Name: Rgs15128128Wr000 Product No.: Gme128128-01

GoldenMorning Electronic
Specification for Approval

PRODUCT NAME: RGS15128128WR000
PRODUCT NO.: GME128128-01
CUSTOMER
APPROVED BY
DATE:
- 1 - REV.: A02 2014/03/31

REVISION RECORD
REV. REVISION DESCRIPTION REV. DATE REMARK
X01 ■ INITIAL RELEASE 2008. 07. 10
X02 ■ Modify definition of panel thickness 2009. 04. 24 Page 5, 6, 7, 8
■ Add lifetime specifications & 16
■ Modify D.C electrical characteristics
■ Add panel electrical specifications
■ Add application circuit
A01 ■ Transfer from X version 2009. 12. 16 Page 5, 18, 19
■ Add the information of module weight & 20
■ Modify seal color (white→black)
■ Add the packing specification
A02 ■ Add appendix of precautions for using 2014. 03. 31 Page 25~34
the OLED module
- 2 - REV.: A02 2014/03/31

CONTENTS
ITEM PAGE
1. SCOPE 4
2. WARRANTY 4
3. FEATURES 4
4. MECHANICAL DATA 5
5. MAXIMUM RATINGS 6
6. ELECTRICAL CHARACTERISTICS 7
6.1 D.C ELECTRICAL CHARACTERISTICS
6.2 ELECTRO-OPTICAL CHARACTERISTICS
7. INTERFACE 9
7.1 FUNCTION BLOCK DIAGRAM
7.2 PANEL LAYOUT DIAGRAM
7.3 PIN ASSIGNMENTS
7.4 GRAPHIC DISPLAY DATA RAM ADDRESS MAP
7.5 INTERFACE TIMING CHART
8. POWER ON / OFF SEQUENCE & APPLICATION CIRCUIT 15
8.1 POWER ON / OFF SEQUENCE
8.2 APPLICATION CIRCUIT
8.3 COMMAND TABLE
9. RELIABILITY TEST CONDITIONS 17
10. EXTERNAL DIMENSION 18
10.1 MODULE ASSEMBLY DRAWING
10.2 FOOTPRINT DRAWING
11. PACKING SPECIFICATION 20
12. APPENDIXES 21
- 3 - REV.: A02 2014/03/31

1. SCOPE
The purpose of this specification is to define the general provisions and quality
requirements that apply to the supply of display cells manufactured by
GoldenMorning. This document, together with the Module Assembly Drawing, is the
highest-level specification for this product. It describes the product, identifies
supporting documents and contains specifications.
2. WARRANTY
GoldenMonring warrants that the products delivered pursuant to this specification (or
order) will conform to the agreed specifications for twelve (12) months from the
shipping date ("Warranty Period"). GoldenMorning is obligated to repair or replace
the products which are found to be defective or inconsistent with the
specifications during the Warranty Period without charge, on condition that the
products are stored or used as the conditions specified in the specifications.
Nevertheless, GoldenMorning is not obligated to repair or replace the products
without charge if the defects or inconsistency are caused by the force majeure
or the reckless behaviors of the customer.
After the Warranty Period, all repairs or replacements of the products are
subject to charge.
3. FEATURES
- Small molecular organic light emitting diode.
- Color : White
- Panel resolution : 128*128
- Driver IC : SSD1327
- Excellent Quick response time : 10µs
- Extremely thin thickness for best mechanism design : 1.41 mm
- High contrast : 2000:1
- Wide viewing angle : 160°
- Strong environmental resistance.
- 8-bit 6800-series Parallel Interface, 8-bit 8080-series Parallel Interface,
Serial Peripheral Interface, I2C Interface.
- Wide range of operating temperature : -40 to 70°C
- Anti-glare polarizer.
- 4 - REV.: A02 2014/03/31

4. MECHANICAL DATA
NO ITEM SPECIFICATION UNIT

1 Dot Matrix 128 x 128 dot
2 Dot Size 0.19 (W) x 0.19 (H) mm2
3 Dot Pitch 0.21 (W) x 0.21 (H) mm2
4 Aperture Rate 82 %
5 Active Area 26.86 (W) x 26.86 (H) mm2
6 Panel Size 33.8 (W) x 36.5 (H) mm2
7* Panel Thickness 1.22 ± 0.1 mm
8 Module Size 33.8 (W) x 43.7 (H) x 1.41 (T) mm3
9 Diagonal A/A size 1.5 inch
10 Module Weight 3.48 ± 10% gram
* Panel thickness includes substrate glass, cover glass and UV glue

thickness.
- 5 - REV.: A02 2014/03/31

5. MAXIMUM RATINGS
ITEM MIN MAX UNIT Condition Remark

IC maximum
Supply Voltage (VCI) -0.3 4 V Ta = 25°C
rating
IC maximum
Supply Voltage (Vcc) 8 19 V Ta = 25°C
rating
Operating Temp. -40 70 °C
Storage Temp -40 85 °C
Humidity 85 %
100 cd/m², 50%
Life Time 10,000 - Hrs Note (1)
checkerboard
90 cd/m², 50%
checkerboard
80 cd/m², 50%
checkerboard
Note:
(A) Under Vcc = 15V, Ta = 25°C, 50% RH.
(B) Life time is defined the amount of time when the luminance has decayed
to less than 50% of the initial measured luminance.
(1) Setting of 100 cd/m2 :
- Contrast setting : 0x9b
- Frame rate : 105Hz
- Duty setting : 1/128
- Contrast setting : 0x77
- 6 - REV.: A02 2014/03/31

6. ELECTRICAL CHARACTERISTICS
6.1 D.C ELECTRICAL CHARACTERISTICS
TEST
SYMBOL PARAMETERS MIN TYP MAX UNIT
CONDITION
Driver power supply
VCC - 14.5 15 15.5 V
(for OLED panel)
Low voltage power
VCI - 2.6 - 3.5 V
supply
VOH High logic output level
Iout=100 uA, 0.9* VCI - VCI V
VOL Low logic output level
Iout=100uA, 0 - 0.1* VCI V
VIH High logic input level
Iout=100uA, 0.8* VCI - VCI V
VIL Low logic input levelIout=100uA, 0 - 0.2* VCI V
VCI = 3.5V,
VCC = 18V, External
600 750
Display ON, VDD= 2.5V
ICC VCC Supply Current uA
No panel
attached, Internal
600 750
contrast = FF VDD= 2.5V
VCI = 3.5V,
VCC = 18V, External
35 50
Display ON, VDD= 2.5V
ICI VCI Supply Current uA
No panel
attached, Internal
95 120
contrast = FF VDD= 2.5V
Contrast=FF - 300 370 uA
Segment output Contrast=AF - 206 - uA
ISEG current Setting Contrast=7F - 150 - uA
VCC=18V, IREF=10uA Contrast=3F - 75 - uA
Contrast=1F - 37.5 - uA
- 7 - REV.: A02 2014/03/31

6.2 ELECTRO-OPTICAL CHARACTERISTICS
PANEL ELECTRICAL SPECIFICATIONS

PARAMETER MIN TYP. MAX UNITS COMMENTS
Normal mode current
- 32 34 mA All pixels on
consumption
Standby mode Standby mode
- 3 4 mA
current consumption 10% pixels on
Normal mode power
- 480 510 mW All pixels on
consumption
Standby mode power Standby mode
- 45 60 mW
consumption 10% pixels on
Pixel Luminance 70 90 cd/m2 Display Average
Standby Luminance 20 cd/m2
CIEx (White) 0.24 0.28 0.32 CIE1931
CIEy (White) 0.28 0.32 0.36 CIE1931
Dark Room Contrast 2000:1
Viewing Angle 160 degree
Response Time 10 µs
Normal mode condition :
- Driving Voltage : 15V
Standby mode condition :
- Driving Voltage : 15V
- 8 - REV.: A02 2014/03/31

7. INTERFACE
7.1 FUNCTION BLOCK DIAGRAM
7.2 PANEL LAYOUT DIAGRAM
- 9 - REV.: A02 2014/03/31

7.3 PIN ASSIGNMENTS
PIN
PIN NO DESCRIPTION
NAME
VSS 1 Ground.
VCC 2 Power supply for analog circuit.
Com Voltage Output. A capacitor should be connected
VCOMH 3
between this pin and VSS.
GPIO 4 General I/O port.
VCI 5 Power supply for logic circuit.
A capacitor should be connected between this pin and
VDD 6
VSS.
BS1 7 MCU bus interface selection pins.
BS2 8 MCU bus interface selection pins.
VSS 9 Ground.
Reference current input pin.
IREF 10
A resistor should be connected between this pin and VSS.
CS# 11 Chip select input.
Reset signal input.
RES# 12
When it’s low, initialization of SSD1327 is executed.
Data/ Command control.
D/C 13 Pull high for write/read display data.
Pull low for write command or read status.
MCU interface input.
WR# 14
Data write operation is initiated when it’s pull low.
MCU interface input.
RD# 15
Data read operation is initiated when it’s pull low.
D0 16
D1 17
D2 18
D3 19
Data bus(for parallel interface)
D4 20
D5 21
D6 22
D7 23
VCC 24 Power supply for analog circuit.
VSS 25 Ground.
- 10 - REV.: A02 2014/03/31

7.4 GRAPHIC DISPLAY DATA RAM ADDRESS MAP
The GDDRAM is a bit mapped static RAM holding the bit pattern to be displayed.
The size of the RAM is 128x128x4 bits. For mechanical flexibility, re-mapping on
both Segment and Common outputs can be selected by software. The
GDDRAM address maps below tables show some examples on using the
command “Set Re-map” A0h to re-map the GDDRAM. In the following tables,
the lower nibble and higher nibble of D0, D1, D2 … D8189, D8190, D8191
represent the 128x128 data bytes in the GDDRAM.
The GDDRAM map under the following condition:

Command “Set Re-map” A0h is set to:
Disable Column Address Re-map (A[0]=0)
Disable Nibble Re-map (A[1]=0)
Enable Horizontal Address Increment (A[2]=0)
Disable COM Re-map (A[4]=0)
Display Start Line=00h
Data byte sequence: D0, D1, D2 … D8191
- 11 - REV.: A02 2014/03/31

Enable Vertical Address Increment (A[2]=1)

Enable Column Address Re-map (A[0]=1)
Enable Nibble Re-map (A[1]=1)
- 12 - REV.: A02 2014/03/31

The example in which the display start line register is set to 10h with the
following condition:
Enable COM Re-map (A[4]=1)
Display Start Line=78h (corresponds to COM119)

Column Start Address=01h
Column End Address=3Eh
Row Start Address=01h
Row End Address=7Eh
- 13 - REV.: A02 2014/03/31

7.5 INTERFACE TIMING CHART
- 14 - REV.: A02 2014/03/31

8. POWER ON / OFF SEQUENCE & APPLICATION CIRCUIT
8.1 POWER ON / OFF SEQUENCE
Power ON sequence:
1. Power ON VCI.
2. After VCI becomes stable, set wait time at least 1ms (t0) for internal VDD become stable. Then
(4)
set RES# pin LOW (logic low) for at least 100us (t1) and then HIGH (logic high).
(1)
3. After set RES# pin LOW (logic low), wait for at least 100us (t2). Then Power ON VCC.
4. After VCC become stable, send command AFh for display ON. SEG/COM will be ON after
200ms(tAF).
Power OFF sequence:

1. Send command AEh for display OFF.
(1), (2), (3)
2. Power OFF VCC.
(5)
3. Wait for tOFF. Power OFF VCI.(where Minimum tOFF=80ms , Typical tOFF=100ms)
Note:
(1) Since an ESD protection circuit is connected between VCI and VCC, VCC becomes lower than
VCI whenever VCI is ON and VCC is OFF as shown in the dotted line of VCC in above figures.
(2) VCC should be kept disable when it is OFF.
(3) Power pins (VCI, VCC) can never be pulled to ground under any circumstance.
(4) The register values are reset after t1.
(5) VCI should not be Power OFF before VCC Power OFF
- 15 - REV.: A02 2014/03/31

8.2 APPLICATION CIRCUIT
Component:
C1, C2: 4.7uF/35V(Tantalum type) or VISHAY (572D475X0025A2T)
C3, C4: 1uF/16V(0603)
R1: 1M ohm (0603) 1%
This circuit is for 8080 8bits interface.
8.3 COMMAND TABLE
Refer to IC Spec.: SSD1327
- 16 - REV.: A02 2014/03/31

9. RELIABILITY TEST CONDITIONS
No. Items Specification Quantity

High temp.
1 85°C, 240hrs 5
(Non-operation)
2 High temp. (Operation) 70°C, 120hrs 5
3 Low temp. (Operation) -40°C, 120hrs 5
High temp. / High
4 65°C, 90%RH, 120hrs 5
humidity (Operation)
-40°C ~85°C (-40°C /30min;
Thermal shock
5 transit /3min; 85°C /30min; transit 5
(Non-operation)
/3min) 1cycle: 66min, 100 cycles
Frequency : 5~50HZ, 0.5G

Scan rate : 1 oct/min
6 Vibration 1 Carton
Time : 2 hrs/axis
Test axis : X, Y, Z
Height: 120cm
Sequence : 1 angle、3 edges and
7 Drop 1 Carton
6 faces
Cycles: 1
Air discharge model, ±8kV, 10
8 ESD (Non-operation) 5
times
Test and measurement conditions

1. All measurements shall not be started until the specimens attain to
temperature stability.
2. All-pixels-on is used as operation test pattern.
3. The degradation of Polarizer are ignored for item 1, 4 & 5.
Evaluation criteria
1. The function test is OK.
2. No observable defects.
3. Luminance: > 50% of initial value.
4. Current consumption: within ± 50% of initial value.
- 17 - REV.: A02 2014/03/31

10. EXTERNAL DIMENSION
10.1 MODULE ASSEMBLY DRAWING
GME128128-01
ＧｏｌｄｅｎＭｏｒｎｉｎｇ　Ｅｌｅｃｔｒｏｎｉｃ
- 18 - REV.: A02 2014/03/31
10.2 FOOTPRINT DRAWING
- 19 - REV.: A02 2014/03/31

11. PACKING SPECIFICATION
ＧｏｌｄｅｎＭｏｒｎｉｎｇ　Ｅｌｅｃｔｒｏｎｉｃ
- 20 - REV.: A02 2014/03/31

12. APPENDIXES
APPENDIX 1: DEFINITIONS
A. DEFINITION OF CHROMATICITY COORDINATE
The chromaticity coordinate is defined as the coordinate value on the CIE 1931
color chart for R, G, B, W.
B. DEFINITION OF CONTRAST RATIO
The contrast ratio is defined as the following formula:
Luminance of all pixels on measurement

Contrast Ratio =
Luminance of all pixels off measurement
C. DEFINITION OF RESPONSE TIME
The definition of turn-on response time Tr is the time interval between a pixel
reaching 10% of steady state luminance and 90% of steady state luminance.
The definition of turn-off response time Tf is the time interval between a pixel
reaching 90% of steady state luminance and 10% of steady state luminance.
It is shown in Figure 2.
Brightness
100%
90%
10%
Tr Tf
Figure 2 Response time
- 21 - REV.: A02 2014/03/31

D. DEFINITION OF VIEWING ANGLE
The viewing angle is defined as Figure 3. Horizontal and vertical (H & V)

angles are determined for viewing directions where luminance varies by 50%
of the perpendicular value.
θ = 0°
φ = 0° +y
+y
+θ
-θ -φ +φ
+x
+x -x
-x
(θ direction)
(φ dire ction )
-y -y
Figure 3 Viewing angle
- 22 - REV.: A02 2014/03/31

APPENDIX 2: MEASUREMENT APPARATUS
A. LUMINANCE/COLOR COORDINATE
PHOTO RESEARCH PR-705, MINOLTA CS-100
Measurement
Header
PR-705 /
MINOLTA CS-100
Panel
Color Analyzer
Plate Form
B. CONTRAST / RESPONSE TIME / VIEWING ANGLE
WESTAR CORPORATION FPM-510
Measurement
Header
Westar FPM-510
Display Contrast /
Panel
Response time /
View angle Analyzer
Plate Form
- 23 - REV.: A02 2014/03/31

C. ESD ON AIR DISCHARGE MODE
R 330 ohms ESD
DISCHARGE
TIP
V C EUT
150pF
RETURN
GROUND PLANE
- 24 - REV.: A02 2014/03/31

APPENDIX 3: PRECAUTIONS FOR USING THE OLED MODULE
Precautions for Handling

1. When handling the module, wear powder-free antistatic rubber finger cots,
and be careful not to bend and twist it.
2. The OLED module is consisted of glass and film, and it should avoid
pressure, strong impact, or being dropped from a high position.
3. The OLED module is an electronic component and is subject to damage

caused by Electro Static Discharge (ESD). And hence normal ESD
precautions must be taken when handling it. Also, appropriate ESD
protective environment must be administered and maintained in the
production line. When handling and assembling the panel, wear an antistatic
wrist strap with the alligator clip attached to the ground to prevent ESD
damage on the panel. Also, ground the tools being used for panel assembly
and make sure the working environment is not too dry to cause ESD
problems. Antistatic wrist strap should touch human body directly instead of
gloves. (See below photos).
4. Take out the panel one by one from the holding trays for assembly, and
never put the panel on top of another one to avoid the scratch.
5. Avoid jerk and excessive bend on TAB/FPC/COF, and be careful not to let
foreign matter or bezel damage the film.
6. When handling and assembling the module (panel + IC), grab the panel, not
the TAB/FPC/COF.
7. Use the tweezers to open the clicks on the connector of PCB before the
insertion of FPC/COF, and click them back in. Once the FPC/COF sits
properly in the connector, use the tweezers to avoid the damages.
- 25 - REV.: A02 2014/03/31

8. Please do not bend the film near the substrate glass. It could cause film
peeling and TAB/FPC/COF damage. For TAB, It should bend the slit area as
actual OLED it is. For FPC or COF, it is suggested to follow below pictures
for instruction (distance between substrate glass and bending area >1.5mm;
R>0.5mm).
- 26 - REV.: A02 2014/03/31

9. Avoid bending the film at IC bonding area. It could damage the IC ILB
bonding. It should avoid bending the IC seal area. Please keep the bending
distance >1.5mm.
10. Use both thumbs to insert COF into the connector when assembling the
panel. Please refer to the photo.
11. The working area for the panel should be kept clean. If the panel is
accidentally dropped on the floor, do visual inspection of the panel first.
Please use clean-room wiping cloth moistened with alcohol to wipe it off if
dirt or grease stains the panel.
- 27 - REV.: A02 2014/03/31

12. Do not wipe the pin of film and polarizer with the dry or hard materials that
will damage the surface. When cleaning the display surface, use the soft
cloth with solvent, IPA or alcohol, to clean.
13. Protection film is applied to the surface of OLED panel to avoid the scratch.
Please remove the protective film before assembling it. If the OLED panel
has been stored for a long time, the residue adhesive material of the
protective film may remain on the display surface after remove the protective
film. Please use the soft cloth with solvent, IPA or alcohol, to clean.
14. When hand or hot-bar soldering TAB/FPC onto PCB, make sure the
temperature and timing profiles to meet the requirements of soldering
specification (the specification depends on the application or optimized by
customer) to prevent the damage of IC pins by inappropriate soldering.
15. Solder residues arise from soldering process have to be cleaned up

thoroughly before the module assembly.
16. Use the voltage and current settings listed in the specification to do the
function test after the module assembly.
17. Suggestion for soldering process:

i. TAB Lead- free soldering hot bar process
1. Use pulse heated bonding tool equipment
2. Material: Sn/Ag/Cu lead-free solder paste with typical 25um
thickness on PCB pad. The TAB pin size and shape may be
different, please base on the production line to adjust the thickness
of PCB pad and temperature.
3. Bonding Force:--4kg per centimeter square as the starting point.
4. Suggested bonding tool temperature & time profile is as below for
reference. Since there are differences in TAB soldering pins,
soldering technicians’ skills, mechanism…etc., the soldering
conditions must be adequately tuned.
- 28 - REV.: A02 2014/03/31

ii. TAB Lead- free soldering wire process
In case of manual soldering (Lead- free solder wire)
1. Solder wire contact iron directly: 280±5℃ at 3-5secs
2. Solder wire contact TAB lead directly (near iron but not contact):
380±5 ℃, 3-5secs
3. Since there are differences in TAB soldering pins, soldering
technicians’ skills, mechanism…etc., the soldering conditions must
be adequately tuned.
iii. High temperature will result in rapid heat conduction to IC and might
cause damage to IC, so please keep the temperature below 380 ℃.
Also, avoid damaging the polyimide and solder resist which might
take place at high temperatures. Refold cycles base on the
de-soldering status, if the plating of pin was damaged, it can not be
used again.
- 29 - REV.: A02 2014/03/31

Precautions for Electrical
1. Design using the settings in the specification
It is very important to design and operate the panel using the settings listed
in the specification. It includes voltage, current, frame rate and duty cycle... etc.
Operation the OLED outside the range of the specification should be entirely
avoided to ensure proper operation of the OLED.
2. Maximum Ratings
To ensure the proper operation of the panel, never design the panel with
parameters running over the maximum ratings listed in the specification. Also
the logic voltages such as VIL and VIH have to be within the specified range in
the specification to prevent any improper operation of the panel.
3. Power on/off procedure

To avoid any inadvertent effects resulting from inappropriate power on/off
operations, please follow the directions of power on/off procedure on page 6.
Any operation that does not comply with the procedure could cause permanent
damage of the IC and should be avoided. When the logic power is not on, do not
activate any input signal. Abrupt shutdown of power to the module, while the
OLED panel is on, would cause OLED panel malfunction.
Display turn on Display turn off

sequence sequence
DC-DC power off DC-DC power on Send display off

(VCC turn off) (VCC turn on) command
Wait 100ms for DC-DC power off

VDD power on
VCC stable (VCC turn off)
Hardware RESET
Wait 100ms for
RESET time depends Display on
on driver IC datasheet VCC reach 0V
Display start and

Display off VDD power turn off
end address setting
Driver IC initial Send display data
- 30 - REV.: A02 2014/03/31

4. Power savings
To save power consumption of the OLED, please use partial display or
sleep mode when the panel is not fully activated. Also, if possible, make the
black background to save power.
The OLED is a self-luminous device and a particular pixel cluster or image
can be lit on via software control. So power savings can be achieved by partial
display or dimming down the luminance. Depending on the application, the user
can choose among Ultra Bright Mode, Normal Operation Mode, and Sleeping
Mode. The power consumption is almost in directly proportion to the brightness
of the panel, and also in directly proportion to the number of pixels lit on the
panel. The customer can save the power by the use of black background and
sleeping mode. One benefit from using these design schemes is the extension
of the OLED lifetime.
5. Adjusting the luminance of the panel

Although there are a couple of ways to adjust the luminance of the panel, it
is strongly recommended that the customer change the contrast setting to adjust
the luminance of the panel. Adjusting voltages to achieve desired luminance is
not allowed. Be aware that the adjustment of luminance would accompany the
change of lifetime of the panel and its power consumption as well.
6. Residual Image (Image Sticking)

The OLED is a self-emissive device. As with other self-emissive device or
displays consisting of self-emissive pixels, when a static image frozen for a long
period of time is changed to another one with all-pixels-on background, residual
image or image sticking is noticed by the human eye. Image sticking is due to
the luminance difference or contrast between the pixels that were previously
turned on and the pixels that are newly turned on. Image sticking depends on
the luminance decay curve of the display. The slower the decay, the less
prominent the image sticking is. It is strongly recommended that the user
employ the following three strategies to minimize image sticking.
- 31 - REV.: A02 2014/03/31

1. Employ image scrolling or animation to even out the lit-on time of
each and every pixel on the display, also could use sleeping mode
for reduced the residual image and extend the power capacity.
2. Minimize the use of all-pixels-on or full white background in their
application because when the panel is turned on full white, the
image sticking from previously shown patterns is the most
revealing. Black background is the best for power savings, greatest
visibility, eye appealing, and dazzling displays
3. If a static logo is used in the reliability test, change the pattern into
its inverse (i.e., turn off the while pixels and turn on the previously
unlit pixels) and freeze the inverse pattern as long as the original
logo is used, so every pixel on the panel can be lit on for about the
same time to minimize image sticking, caused by the differential
turn-on time between the original and its reverse patterns.
Scrolling example
- 32 - REV.: A02 2014/03/31

Precautions for Mechanical
1. Cushion or Buffer tape on the cover glass
It is strongly recommended to have a cushion or buffer tape to apply on the
panel backside and front side when assembling OLED panel into module to
protect it from damage due to excessive extraneous forces.
It is recommended that a plating conductive layer be used in the housing for

EMI/EMC protection. And, the enough space should be reserved for the IC
placement if the IC thickness is thicker than the TAB film when customer design
the PCB.
2. Avoid excessive bending of film when handling or designing the panel

into the product
The bending of TAB/COF/FPC has to follow the precautions indicated in
the specification, extra bending or excessive extraneous forces should be
avoided to minimize the chances of film damage. If bending the film is
necessary, please bend the designated bending area only. Please refer to items
8 and 9 of Precautions for Handling for more information.
- 33 - REV.: A02 2014/03/31

Precautions for Storage and Reliability Test
1. Storage
Store the packed cartons or packages at 25℃±5℃, 55%±10%RH. Do not
store the OLED module under direct sunlight or UV light. For best panel
performance, unpack the cartons and start the production of the panels within
six months after the reception of them.
2. Reliability Test
GoldenMorning only guarantees the reliability of the OLEDs under the test
conditions and durations listed in the specification.
- 34 - REV.: A02 2014/03/31

Goldenmorning Electronic: Product Name: Rgs15128128Wr000 Product No.: Gme128128-01

Uploaded by

Copyright:

Available Formats

Goldenmorning Electronic: Product Name: Rgs15128128Wr000 Product No.: Gme128128-01

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Goldenmorning Electronic: Product Name: Rgs15128128Wr000 Product No.: Gme128128-01

Uploaded by

Copyright:

Available Formats

GoldenMorning Electronic

Specification for Approval

- 1 - REV.: A02 2014/03/31

- 2 - REV.: A02 2014/03/31

- 3 - REV.: A02 2014/03/31

- 4 - REV.: A02 2014/03/31

NO ITEM SPECIFICATION UNIT

* Panel thickness includes substrate glass, cover glass and UV glue

- 5 - REV.: A02 2014/03/31

ITEM MIN MAX UNIT Condition Remark

- 6 - REV.: A02 2014/03/31

6.1 D.C ELECTRICAL CHARACTERISTICS

- 7 - REV.: A02 2014/03/31

PANEL ELECTRICAL SPECIFICATIONS

- 8 - REV.: A02 2014/03/31

7.1 FUNCTION BLOCK DIAGRAM

7.2 PANEL LAYOUT DIAGRAM

- 9 - REV.: A02 2014/03/31

- 10 - REV.: A02 2014/03/31

The GDDRAM map under the following condition:

- 11 - REV.: A02 2014/03/31

The GDDRAM map under the following condition:

- 12 - REV.: A02 2014/03/31

The GDDRAM map under the following condition:

- 13 - REV.: A02 2014/03/31

- 14 - REV.: A02 2014/03/31

Power OFF sequence:

- 15 - REV.: A02 2014/03/31

8.3 COMMAND TABLE

Refer to IC Spec.: SSD1327

- 16 - REV.: A02 2014/03/31

No. Items Specification Quantity

Frequency : 5~50HZ, 0.5G

Test and measurement conditions

- 17 - REV.: A02 2014/03/31

- 19 - REV.: A02 2014/03/31

- 20 - REV.: A02 2014/03/31

A. DEFINITION OF CHROMATICITY COORDINATE

B. DEFINITION OF CONTRAST RATIO

The contrast ratio is defined as the following formula:

Luminance of all pixels on measurement

C. DEFINITION OF RESPONSE TIME

Figure 2 Response time

- 21 - REV.: A02 2014/03/31

The viewing angle is defined as Figure 3. Horizontal and vertical (H & V)

Figure 3 Viewing angle

- 22 - REV.: A02 2014/03/31

PHOTO RESEARCH PR-705, MINOLTA CS-100

B. CONTRAST / RESPONSE TIME / VIEWING ANGLE

WESTAR CORPORATION FPM-510

- 23 - REV.: A02 2014/03/31

R 330 ohms ESD

- 24 - REV.: A02 2014/03/31

Precautions for Handling

3. The OLED module is an electronic component and is subject to damage

- 25 - REV.: A02 2014/03/31

- 26 - REV.: A02 2014/03/31

- 27 - REV.: A02 2014/03/31