Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

1 Input Data: Profis Anchor 2.9.0

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

www.hilti.com.sg Profis Anchor 2.9.

0
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

Specifier's comments:

1 Input data
Anchor type and diameter: HSA-R M12 hnom3
Return period (service life in years): 50
Effective embedment depth: hef = 100 mm, hnom = 114 mm
Material: A4
Evaluation Service Report: ETA 11/0374
Issued I Valid: 8/28/2017 | -
Proof: Design method ETAG (No. 001 Annex C/2010)
Stand-off installation: eb = 0 mm (no stand-off); t = 6 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 85 mm x 225 mm x 6 mm; (Recommended plate thickness: calculated (4 mm))
Profile: Double flat bar, ; (L x W x T) = 85 mm x 87 mm x 6 mm
Base material: uncracked concrete, C30/37, fc,cube = 37.00 N/mm2; h = 300 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement

R
- The anchor calculation is based on a rigid anchor plate assumption.

Geometry [mm] & Loading [kN, kNm]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.sg Profis Anchor 2.9.0
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

2 Load case/Resulting anchor forces y


Load case: Design loads
2

Anchor reactions [kN]


Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
Compression
1 2.175 1.818 1.818 0.000
2 2.175 1.818 1.818 0.000 x
Tension
max. concrete compressive strain: 0.09 [‰]
max. concrete compressive stress: 2.69 [N/mm2]
resulting tension force in (x/y)=(0/0): 4.350 [kN]
resulting compression force in (x/y)=(38/0): 4.350 [kN]
1
Anchor forces are calculated based on the assumption of a rigid anchor plate.

3 Tension load (ETAG, Annex C, Section 5.2.2)


Load [kN] Capacity [kN] Utilization bN [%] Status
Steel Strength* 2.175 31.857 7 OK
Pullout Strength* 2.175 28.386 8 OK
Concrete Breakout Strength** 4.350 36.857 12 OK
Splitting failure** 4.350 34.131 13 OK
* anchor having the highest loading **anchor group (anchors in tension)

3.1 Steel Strength


NRk,s [kN] gM,s NRd,s [kN] NSd [kN]
44.600 1.400 31.857 2.175

3.2 Pullout Strength


NRk,p [kN] yc gM,p NRd,p [kN] NSd [kN]
35.000 1.217 1.500 28.386 2.175

3.3 Concrete Breakout Strength


Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm]
91,000 90,000 150 300
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 0.890 1.000
k1 N0Rk,c [kN] gM,c NRd,c [kN] NSd [kN]
10.100 61.436 1.500 36.857 4.350
Group anchor ID
1, 2

3.4 Splitting failure


Ac,N [mm2] A0c,N [mm2] ccr,sp [mm] scr,sp [mm] y h,sp
93,000 96,100 155 310 1.406
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N k1
0 1.000 0 1.000 0.884 1.000 10.100
N0Rk,c [kN] gM,sp NRd,sp [kN] NSd [kN]
42.579 1.500 34.131 4.350
Group anchor ID
1, 2

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.sg Profis Anchor 2.9.0
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

4 Shear load (ETAG, Annex C, Section 5.2.3)


Load [kN] Capacity [kN] Utilization bV [%] Status
Steel Strength (without lever arm)* 1.818 23.440 8 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 3.636 73.714 5 OK
Concrete edge failure in direction x+** 3.636 26.836 14 OK
* anchor having the highest loading **anchor group (relevant anchors)

4.1 Steel Strength (without lever arm)


VRk,s [kN] gM,s VRd,s [kN] VSd [kN]
29.300 1.250 23.440 1.818

4.2 Pryout Strength


Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm] k-factor
91,000 90,000 150 300 2.000
ec1,V [mm] y ec1,N ec2,V [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 0.890 1.000
N0Rk,c [kN] gM,c,p VRd,cp [kN] VSd [kN]
61.436 1.500 73.714 3.636
Group anchor ID
1, 2

4.3 Concrete edge failure in direction x+


lf [mm] dnom [mm] k1 a b
100 12.0 2.400 0.098 0.065
c1 [mm] Ac,V [mm2] A0c,V [mm2]
105 74,025 49,613
y s,V y h,V y a,V ec,V [mm] y ec,V y re,V
1.000 1.000 1.000 0 1.000 1.000
V0Rk,c [kN] gM,c VRd,c [kN] VSd [kN]
26.979 1.500 26.836 3.636

5 Combined tension and shear loads (ETAG, Annex C, Section 5.2.4)

Steel failure
bN bV a Utilization bN,V [%] Status
0.127 0.135 1.500 10 OK
baN + baV ≤ 1.0

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.sg Profis Anchor 2.9.0
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

6 Displacements (highest loaded anchor)


Short term loading:
NSk = 1.611 [kN] dN = 0.222 [mm]
VSk = 1.347 [kN] dV = 0.169 [mm]
dNV = 0.279 [mm]
Long term loading:
NSk = 1.611 [kN] dN = 0.260 [mm]
VSk = 1.347 [kN] dV = 0.258 [mm]
dNV = 0.367 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!

The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid anchor plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the anchor plate without creating air voids and before application of the loads.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• The characteristic bond resistances depend on the return period (service life in years): 50

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.sg Profis Anchor 2.9.0
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

8 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HSA-R M12 hnom3
Profile: Double flat bar, ; (L x W x T) = 85 mm x 87 mm x 6 mm Installation torque: 0.050 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm
Plate thickness (input): 6 mm Hole depth in the base material: 122 mm
Recommended plate thickness: calculated (4 mm) Minimum thickness of the base material: 180 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions
for use is required.

8.1 Recommended accessories

Drilling Cleaning Setting


• Suitable Rotary Hammer • Manual blow-out pump • Installation torque control bar with suitable
• Properly sized drill bit screw driver or torque wrench
• Hammer
y

43 43
35

2
113
155

x
113

1
35

43 43

Coordinates Anchor [mm]


Anchor x y c-x c+x c-y c+y
1 0 -78 95 105 - -
2 0 78 95 105 - -

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.sg Profis Anchor 2.9.0
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 19/11/2020
E-Mail:

9 Remarks; Your Cooperation Duties


• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan

You might also like