This document provides the input data and results of an anchor calculation using Profis Anchor software. The anchor type is a HIT-HY 200-R V3 + HAS-U 8.8 M20 anchor with an effective embedment depth of 150mm installed in cracked concrete with a compressive strength of 25 MPa. The calculation checks four failure modes - steel strength, combined pullout-concrete cone, concrete breakout strength, and splitting failure - and confirms the 139kN design load is below the capacity for each failure mode, with utilization rates between 27-98%. The anchor group of four anchors passed all checks according to the given codes and standards.
This document provides the input data and results of an anchor calculation using Profis Anchor software. The anchor type is a HIT-HY 200-R V3 + HAS-U 8.8 M20 anchor with an effective embedment depth of 150mm installed in cracked concrete with a compressive strength of 25 MPa. The calculation checks four failure modes - steel strength, combined pullout-concrete cone, concrete breakout strength, and splitting failure - and confirms the 139kN design load is below the capacity for each failure mode, with utilization rates between 27-98%. The anchor group of four anchors passed all checks according to the given codes and standards.
This document provides the input data and results of an anchor calculation using Profis Anchor software. The anchor type is a HIT-HY 200-R V3 + HAS-U 8.8 M20 anchor with an effective embedment depth of 150mm installed in cracked concrete with a compressive strength of 25 MPa. The calculation checks four failure modes - steel strength, combined pullout-concrete cone, concrete breakout strength, and splitting failure - and confirms the 139kN design load is below the capacity for each failure mode, with utilization rates between 27-98%. The anchor group of four anchors passed all checks according to the given codes and standards.
This document provides the input data and results of an anchor calculation using Profis Anchor software. The anchor type is a HIT-HY 200-R V3 + HAS-U 8.8 M20 anchor with an effective embedment depth of 150mm installed in cracked concrete with a compressive strength of 25 MPa. The calculation checks four failure modes - steel strength, combined pullout-concrete cone, concrete breakout strength, and splitting failure - and confirms the 139kN design load is below the capacity for each failure mode, with utilization rates between 27-98%. The anchor group of four anchors passed all checks according to the given codes and standards.
3 Company: Page: 1 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
Specifier's comments:
1 Input data Anchor type and diameter: HIT-HY 200-R V3 + HAS-U 8.8 M20 Return period (service life in years): 50 Seismic/Filling set or any suitable annular gap filling solution Effective embedment depth: hef,act = 150 mm (hef,limit = - mm) Material: 8.8 Evaluation Service Report: ETA 19/0601 Issued I Valid: 12/14/2020 | - Proof: SOFA design method + fib (07/2011) - after ETAG BOND testing Stand-off installation: eb = 0 mm (no stand-off); t = 20 mm Anchor plate: lx x ly x t = 450 mm x 450 mm x 20 mm; (Recommended plate thickness: not calculated Profile: Square hollow, 250 x 250 x 8,0; (L x W x T) = 250 mm x 250 mm x 8 mm Base material: cracked concrete, C25/30, fc,cyl = 25.00 N/mm2; h = 250 mm, Temp. short/long: 30/40 °C Installation: hammer drilled hole, Installation condition: Dry Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm) no longitudinal edge reinforcement
R - The anchor calculation is based on a rigid anchor plate assumption.
Geometry [mm] & Loading [kN, kNm]
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan www.hilti.ae Profis Anchor 2.9.3 Company: Page: 2 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
2 Load case/Resulting anchor forces y
Load case: Design loads 3 4
Anchor reactions [kN]
Tension force: (+Tension, -Compression) Anchor Tension force Shear force Shear force x Shear force y 1 34.750 0.000 0.000 0.000 2 34.750 0.000 0.000 0.000 x 3 34.750 0.000 0.000 0.000 Tension 4 34.750 0.000 0.000 0.000
max. concrete compressive strain: - [‰]
max. concrete compressive stress: - [N/mm2] resulting tension force in (x/y)=(0/0): 139.000 [kN] 1 2 resulting compression force in (x/y)=(0/0): 0.000 [kN]
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Ap,N [mm2] A0p,N [mm2] y A,Np 2 t Rk,ucr,25 [N/mm ] scr,Np [mm] ccr,Np [mm] cmin [mm] 640,000 202,500 3.160 15.00 450 225 225 2 0 yc t Rk,cr [N/mm ] max t Rk,cr [N/mm2] y g,Np y g,Np 1.020 7.14 7.50 1.072 1.008 ec1,N [mm] y ec1,Np ec2,N [mm] y ec2,Np y s,Np y re,Np 0 1.000 0 1.000 1.000 1.000 N0Rk,p [kN] NRk,p [kN] gM,p NRd,p [kN] NSd [kN] 67.310 214.532 1.500 143.021 139.000 Group anchor ID 1-4
3.3 Concrete Breakout Strength
Ac,N [mm2] A0c,N [mm2] y A,N ccr,N [mm] scr,N [mm] 640,000 202,500 3.160 225 450 ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N 0 1.000 0 1.000 1.000 1.000 k1 N0Rk,c [kN] gM,c NRd,c [kN] NSd [kN] 7.700 70.729 1.500 149.026 139.000 Group anchor ID 1-4
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan www.hilti.ae Profis Anchor 2.9.3 Company: Page: 3 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
3.4 Splitting failure
Ac,N [mm2] A0c,N [mm2] y A,N ccr,sp [mm] scr,sp [mm] y h,sp 640,000 202,500 3.160 240 480 1.184 h'ef [mm] c'cr,sp [mm] s'cr,sp [mm] 141 225 450 ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N k1 0 1.000 0 1.000 1.000 1.000 7.700 N0Rk,c [kN] gM,sp NRd,sp [kN] NSd [kN] 64.203 1.500 160.193 139.000 Group anchor ID 1-4
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan www.hilti.ae Profis Anchor 2.9.3 Company: Page: 4 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
4 Shear load SOFA (fib (07/2011), section 16.2.2)
Load [kN] Capacity [kN] Utilization bV [%] Status Steel Strength (without lever arm)* N/A N/A N/A N/A Steel failure (with lever arm)* N/A N/A N/A N/A Pryout Strength* N/A N/A N/A N/A Concrete edge failure in direction ** N/A N/A N/A N/A * anchor having the highest loading **anchor group (relevant anchors)
5 Displacements (highest loaded anchor)
Short term loading: NSk = 25.741 [kN] dN = 0.273 [mm] VSk = 0.000 [kN] dV = 0.000 [mm] dNV = 0.273 [mm] Long term loading: NSk = 25.741 [kN] dN = 0.601 [mm] VSk = 0.000 [kN] dV = 0.000 [mm] dNV = 0.601 [mm]
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
6 Warnings • The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility! • The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed to ensure a proper installation. • Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice, blow twice with oil-free compressed air (min. 6 bar)). • Characteristic bond resistances depend on short- and long-term temperatures. • The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling the gap with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means • The compliance with current standards (e.g. EC3) is the responsibility of the user • Checking the transfer of loads into the base material is required in accordance with fib (07/2011)! • The characteristic bond resistances depend on the return period (service life in years): 50
Fastening meets the design criteria!
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan www.hilti.ae Profis Anchor 2.9.3 Company: Page: 5 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
7 Installation data Anchor plate, steel: - Anchor type and diameter: HIT-HY 200-R V3 + HAS-U 8.8 M20 Profile: Square hollow, 250 x 250 x 8,0; (L x W x T) = 250 mm x 250 Maximum installation torque: 0.150 kNm mm x 8 mm Hole diameter in the fixture: df = 22 mm Hole diameter in the base material: 22 mm Plate thickness (input): 20 mm Hole depth in the base material: 150 mm Recommended plate thickness: not calculated Minimum thickness of the base material: 194 mm Drilling method: Hammer drilled Cleaning: Compressed air cleaning of the drilled hole according to instructions for use is required
7.1 Recommended accessories
Drilling Cleaning Setting
• Suitable Rotary Hammer • Compressed air with required • Dispenser including cassette and mixer • Properly sized drill bit accessories to blow from the bottom of • Seismic/Filling set the hole • Torque wrench • Proper diameter wire brush y
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan www.hilti.ae Profis Anchor 2.9.3 Company: Page: 6 Specifier: Project: Address: Sub-Project I Pos. No.: Phone I Fax: | Date: 9/19/2021 E-Mail:
8 Remarks; Your Cooperation Duties
• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or suitability for a specific application. • You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or programs, arising from a culpable breach of duty by you.
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
