PDHengineer.

com
Course № M-2059

Hydraulic Design of Fire Water Sprinkler

Systems Containing Typical Branch Lines

To receive credit for this course

This document is the course text. You may review this material at
your leisure either before or after you purchase the course. To
purchase this course, click on the course overview page:

http://www.pdhengineer.com/pages/M-2059.htm

Or type the link into your browser. Next, click on the Take Quiz
button at the bottom of the course overview page. If you already have
an account, log in to purchase the course. If you do not have a
PDHengineer.com account, click the New User Sign Up link to create
your account.

After logging in and purchasing the course, you can take the online
quiz immediately or you can wait until another day if you have not yet
reviewed the course text. When you complete the online quiz, your
score will automatically be calculated. If you receive a passing score,
you may instantly download your certificate of completion. If you do
not pass on your first try, you can retake the quiz as many times as
needed by simply logging into your PDHengineer.com account and
clicking on the link Courses Purchased But Not Completed.

If you have any questions, please call us toll-free at 877 500-7145.

PDHengineer.com
5870 Highway 6 North, Suite 310
Houston, TX 77084
Toll Free: 877 500-7145
administrator@PDHengineer.com
 Hydraulics for Sprinkler Systems with Typical Branch Lines
Occupancy classification
Any hydraulic design of sprinkler systems must begin with an analysis of the commodity being
protected. The National Fire Protection Association, Standard No. 13 “Installation of Sprinkler
Systems” (NFPA-13) defines three basic commodity classification: Light Hazard, Ordinary Hazard and
Extra Hazard. These classifications are defined in NFPA-13 and examples are given in that document.

Ordinary Hazard occupancies are divided into two categories: Ordinary Hazard Group 1 and Ordinary
Hazard Group 2. Extra Hazard occupancies are also divided into two categories: Extra Hazard Group
1 and Extra Hazard Group 2.

Once a hazard classification is chosen for a known occupancy, the water requirements may be
established from NFPA-13, (2007) Figure 11.2.3.1.1

1
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
Densities and Remote Areas
NFPA-13, (2007) Figure 11.2.3.1.1 displays five density/area curves overlain on a graph. These five
curves correspond to the previously discussed hazard classifications: Light Hazard, Ordinary Group 1
Hazard, Ordinary Group 2 Hazard, Extra Hazard Group 1 and Extra Hazard Group 2.

These curves stipulate the required minimum densities and remote areas that establish minimum water
requirements for sprinkler systems.

Definition:

Density – the amount of water that must be delivered every minute for every square foot of floor space
The English units for density is (gallons per minute per square foot (gpm/sq.ft.) For example, a Light
Hazard occupancy could be designed for a density of 0.1-gpm/sq.ft. This means that 0.1-gallons must
discharge every minute for every square foot of floor space over a specified area.

Definition:

Remote Area – the minimum area of floor space over which the density must discharge.

As an example, Figure 11.2.3.1.1 indicates that an acceptable design for an Ordinary Hazard Group 1
occupancy is 0.15-gpm/sq.ft. over 1500-sq.ft.
2

This means the sprinkler system designer will choose the most hydraulically demanding 1500-sq.ft. of
the sprinkler system layout and perform a calculation of all sprinklers within that 1500-sq.ft. area.
Therefore, only a portion of sprinklers on a sprinkler system are expected to operate during a typical
fire, not all. If all sprinklers on a sprinkler system operate the water supply most likely will not be
adequate to control the fire.

Below is an example remote area for an Ordinary Group 1 occupancy, which in this example is a 1500-
sq.ft. remote area. Note the remote area contains fifteen sprinklers which are numbered 1 – 15. The
most hydraulically remote sprinkler is sprinkler #1, since it is physically the mort remote. There are
cases when the physically remote sprinkler will not be the hydraulically remote. If the hydraulically
remote sprinkler is not evident, additional calculations can be performed to verify.

2
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
Remote Area #1
End sprinkler start conditions
Once the hydraulic requirements are selected for the occupancy, the hydraulic calculation of the
sprinkler system may begin. In modern times sprinkler system hydraulics are performed by computer
programs. However, in the early days of sprinkler system hydraulic design all systems were calculated
with a calculator as we will do here. A thorough understanding of these principles is not required to
perform calculations on a hydraulic calculation program but these are the principles on which the
program operates. A better understanding of these principles will allow the designer to better
understand how the sprinkler system will function hydraulically.

The density/area curves will tell the designer the starting point of the design. Our example is an
Ordinary Hazard Group 1 occupancy and we will choose the point on the density/area curve of 0.15-
gpm/sq.ft. over 1500-sq.ft.

This means that every square foot of the 1500-sq.ft. remote area must be covered with at least 0.15-
gpm. By extension, this means that the floor area under each sprinkler, called the Protection Area of

3
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
Coverage, must be provided with 0.15-gpm/sq.ft. In other words, each sprinkler must discharge
enough water to provide a minimum of 0.15-gallons per minute for every square foot it protects.

Definition:
If the beginning sprinkler in our example protects 130-sq.ft. of floor area, then the amount of water that
must exit theArea
Protection sprinkler is:
of Coverage – the floor area protected by an individual sprinkler.

Ac x D = Qs

Where:
Qs = Flow from individual sprinkler
Ac = Protection Area of Coverage for individual sprinkler
D = Density

0.15 − gpm
Therefore, 130-sq.ft. x = 19.5-gpm.
sq. ft.

The end sprinkler must discharge 19.5-gallons every minute over the 130-sq.ft. it protects in order to
meet the minimum density requirement of NFPA-13. We might start the calculation process at this
point, however there is one other item that must be verified. NFPA-13, (2007) section 22.4.4.10.1
states that no sprinkler may operate at less than 7-psi. This means that we must verify that our end
sprinkler satisfies this condition. For our example, we have chosen a sprinkler with a k-factor of 8.0.
The formula for determining the minimum flow from a sprinkler at a specified pressure is:

Q=k p

Where,
Q = Flow from individual sprinkler
k = Sprinkler k-factor (see NFPA-13, (2007) Table 6.2.3.1)
p = Pressure from an individual sprinkler.

Therefore, Q = 8.0 7 = 21.2-gpm.

Since the sprinkler in our example requires 21.2-gpm to meet the 7-psi requirement and only 19.5-gpm
to meet the density requirement, we must start our end sprinkler at 21.2-gpm.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom lgth Pt 7
ftg Pf
1 Q 21.2 Act.
tot Pe
2 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now that we have our starting conditions entered. We must now calculate the pressure it takes to get
our 21.2-gpm through the piece of pipe supplying sprinkler #1. Take a look again at our remote area:
Sprinkler #1 is supplied by a piece if 1-inch pipe that is 10-feet long. In order to calculate friction loss
through this pipe, we must learn to use the Hazen-Williams friction loss formula.
Hazen-Williams Friction Loss Formula
You will find the Hazen-Williams friction loss formula in NFPA-13 (2007), section 22.4.2.1.1. It is as
follows:

4.52× Q1.85 × L
Pf =
C1.85 × D4.87
Where,
Pf = Total friction loss in piece of pipe (psi)
Q = Total flow in pipe (gpm)
L = Length of pipe (feet)
C = C-factor of pipe (from NFPA-13 (2007) Table 22.4.4.7)
D = Diameter of pipe (inches)

These variables are all self-explanatory except for the C-factor. This variable simulates the internal
roughness of the piece of pipe and differs depending on sprinkler system type and pipe type. NFPA-
13, Table 22.4.4.7 indicates C Values as follows:

4
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
For our sample sprinkler system, will be use Black steel wet system which = C value of 120.

We will enter all of the appropriate information into our calculation formula sheet as follows:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe
2 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Notice the actual pipe diameter is entered in the worksheet and this is the value you will use in your
friction loss calculation. Do not use the nominal diameter of 1.0-inches in the Hazen-Williams
formula. Actual internal diameters of some pipes can be found in NFPA-13, Table A.6.3.2 or
manufacturer’s websites.

The pipe length of 10-0 is entered in the appropriate box but the fitting length is 0-0. There are no
fittings in this piece of pipe that are required to be considered. A discussion of friction loss for fittings
will occur later.

We now have enough information to perform the friction loss calculation in the pipe supplying
sprinkler #1. It is as follows:

4.52 × 21 .21.85 × 10
Pf =
120 1.85 × 1.049 4.87
= 1.449-psi
This friction loss is now entered in the worksheet:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Since there is no elevation change in the ends of this pipe, the pressure loss due to elevation is 0 and is
also entered in the worksheet. Pressure loss due to elevation will be discussed later.
Now that we have the starting pressure at sprinkler #1 and the friction pressure required to get our
21.2-gpm to sprinkler #1, we can add these two to get the pressure needed at sprinkler #2.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q Nom lgth Pt 8.5
ftg Pf
Q Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now that we know the pressure at sprinkler #2, we can calculate the actual flow from sprinkler #2 with
the increased pressure of 8.5-psi. This is done with the equation:

Q = k p which yields
Q = 8.0 8.5 = 23.3-gpm; this is entered in the appropriate place on the worksheet:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom lgth Pt 8.5
ftg Pf
Q Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the flow from sprinkler #1 and sprinkler #2 to get the total flow through the pipe
supplying sprinkler #2. Notice that the variable q = the flow from a single sprinkler and the variable Q
= the total flow in the system.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom lgth Pt 8.5
ftg Pf
Q 44.5 Act.
tot Pe
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now that we know the total flow in the pipe supplying sprinkler #2, we use the Hazen-Williams
formula to calculate the friction loss pressure in the pipe supplying sprinkler #2.
The pipe supplying sprinkler #2 is a piece of 1 ¼-inch schedule 40 10-feet long, which would yield the
following friction loss calculation:

4.52 × 44 .51.85 × 10
Pf =
1201.85 × 1.38 4.87
= 1.50-psi
Enter all of the pipe information and friction loss data in the worksheet.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the pressure at sprinkler #2 and the friction loss through the pipe supplying sprinkler #2 to
get the pressure at sprinkler #3.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q Nom lgth Pt 10.0
ftg Pf
Q Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

At this point you should begin to notice the back-and-forth process of calculating sprinkler flow and
friction loss. Since we last calculated friction loss, this should give a clue that the next step is to
calculate sprinkler flow. Indeed, since we now know the actual pressure at sprinkler #3, we can
calculate the actual flow from sprinkler #3 which is as follows:

Q = k p which yields
Q = 8.0 10.0 = 25.3-gpm; this is entered in the appropriate place on the worksheet and the total flow
also through the pipe supplying sprinkler #3 can be calculated by adding the flow from sprinkler #3 to
the flow through the pipe supplying sprinkler #2.
Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom lgth Pt 10.0
ftg Pf
Q 69.8 Act.
tot Pe
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we will calculate the friction loss pressure in the pipe supplying sprinkler #3.
The pipe supplying sprinkler #3 is a piece of 1 ½-inch schedule 40 10-feet long, which would yield the
following friction loss calculation:

4.52 × 69 .81.85 × 10
Pf =
1201.85 × 1.614.87
= 1.6-psi
Enter all of the pipe information and friction loss data in the worksheet.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the pressure at sprinkler #3 and the friction loss through the pipe supplying sprinkler #3 to
get the pressure at sprinkler #4.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q Nom lgth Pt 11.6
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

If you’ve caught on to the process you will expect that since we now know the actual pressure at
sprinkler #4, we can calculate the actual flow from sprinkler #4 which is as follows:

Q = k p which yields

Q = 8.0 11.6 = 27.2-gpm; this is entered in the appropriate place on the worksheet and the total flow
also through the pipe supplying sprinkler #4 can be calculated by adding the flow from sprinkler #4 to
the flow through the pipe supplying sprinkler #3.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom lgth Pt 11.6
ftg Pf
Q 97.0 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we will calculate the friction loss pressure in the pipe supplying sprinkler #4.
The pipe supplying sprinkler #4 is a piece of 1 ½-inch schedule 40 10-feet long, which would yield the
following friction loss calculation:

4.52 × 97 .01.85 × 10
Pf =
1201.85 × 1.614.87
= 3.0-psi
Enter all of the pipe information and friction loss data in the worksheet.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the pressure at sprinkler #4 and the friction loss through the pipe supplying sprinkler #4 to
get the pressure at sprinkler #5.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q Nom lgth Pt 14.6
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now that we know the actual pressure at sprinkler #5, we can calculate the actual flow from sprinkler
#5 which is as follows:

Q = k p which yields

Q = 8.0 14.6 = 30-6-gpm; this is entered in the appropriate place on the worksheet and the total flow
also through the pipe supplying sprinkler #5 can be calculated by adding the flow from sprinkler #5 to
the flow through the pipe supplying sprinkler #4.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom lgth Pt 14.6
ftg Pf
Q 127.6 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we will calculate the friction loss pressure in the pipe supplying sprinkler #5.
The pipe supplying sprinkler #5 is a piece of 1 ½-inch schedule 40 1’-11 ½-inches long. Also, in this
piece of pipe there is a fitting at the connection to the main which must be accounted for in the friction
loss calculation.

NFPA-13, section 22.4.4.7 (3) states “Calculate the loss for a tee or a cross where flow direction
change occurs based on the equivalent pipe length of the piping segment in which the fitting is
included.” This tells us when to include a fitting in the friction loss calculation, when flow direction
changes.

NFPA-13, section 22.4.4.7 (4) states “The tee at the top of a riser nipple shall be included in the
branch line, the tee at the base of a riser nipple shall be included in the riser nipple, and the tee
or cross at a cross main-feed main junction shall be included in the cross main.” This tells us
where to include the fitting, into upstream piece of pipe. This is why the Tee fitting at the cross main
at point A on our drawing is added to the branch line friction loss calculation and not the friction loss
through the piece of 4-inch main.

If you are wondering about all of those Tee fittings that the sprinklers are threaded into, NFPA-13,
section 22.4.4.7 (9) states “Friction loss shall be excluded for the fitting directly connected to a
sprinkler.” Therefore we ignore the Tee fittings for the sprinklers.

Now we know to include a Tee fitting in our friction loss calculation for the pipe supplying sprinkler
#5. This is entered in our worksheet.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg Pf
Q 127.6 Act. 1.61
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

I’ve also entered the pipe diameter and length. Now that we know there will be one Tee, we must add
some equivalent footage of 1 ½-inch pipe to account for the additional friction loss through the Tee.
This is found in NFPA-13, Table 22.4.3.1.1. In this table the pipe sizes are across the top and the
fittings are along the left side. If you find the intersection of “Tee or cross” and “1 ½ in.”, you will
find an equivalent footage for this fitting of “8”. This means that you include an additional 8-feet in
the friction loss calculation.
5

5
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
When entered into the worksheet it will appear as follows:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 Pf
Q 127.6 Act. 1.61
tot 18-0 Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
This makes our total length of pipe in our friction loss calculation = 18-0, which would yield the
following friction loss calculation:

4.52 × 127 .61.85 × 18

Pf =
1201.85 × 1.614.87
= 9.0-psi

Enter all of the pipe information and friction loss data in the worksheet.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q Nom lgth Pt 23.6
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Adding the pressure at sprinkler #5 and the friction loss pressure in the pipe supplying sprinkler #5, we
have the pressure required at point A in our system. This is 23.6-psi. With this piping arrangement,
23.6-psi is required at point A to get the required minimum amount of water and pressure through
sprinklers #1 through #5.

Since there are no more sprinklers to account for on this line, the next step is to simply calculate the
friction loss from point A to point B.
This pipe is a piece of 4-inch schedule 10 10-feet long, which would yield the following friction loss
calculation:

4.52 × 127 .61.85 × 10

Pf =
1201.85 × 4.26 4.87
= 0.04-psi; I will round this to 0.1-psi.
Enter all of the pipe information and friction loss data in the worksheet.
Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the pressure at point A and the friction loss through the pipe supplying point A to get the
pressure at point B.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q Nom lgth Pt 23.7
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now that we are at point B in the system we must add the flow for sprinklers #6 through #10. Since
this branch line is typical to the first, we can use an additional formula to calculate the additional flow
through this second branch line due to the increased pressure at point B of 23.7-psi.
Flow Adjustments
Flow adjustments are required to balance two different calculated flows at the same point in a sprinkler
system. Obviously, two separate flows and pressure cannot exist at the same point. Notice below that
the pressure at point A, where the first branch line connects to the main is 23.6-psi but the pressure at
point B, where the second branch line connects to the main is 23.7-psi. Since the pressure is increased
at point B, all of the sprinklers will overflow due to the higher pressure. However, in order to continue
our calculation we must know how much water will actually flow through the second branch line.

The formula used to calculate this is as follows:

PH
Qadj = QL ×
PL

Where:
Qadj = Adjusted Flow
QL = Calculated Flow in the Low Pressure Line
PH = Calculated Pressure in the High Pressure Line
PL = Calculated Pressure in the Low Pressure Line
Note the two pressures highlighted in the worksheet below:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q Nom lgth Pt 23.7
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The pressure required to get our minimum end sprinkler conditions down our typical branch line was
calculated to be 23.6-psi at point A. But our pressure at point B is 23.7-psi. Our calculated flow for
our typical branch line was 127.6-gpm. We can use our formula to calculate the actual flow down our
second branch line based on the higher pressure.
 PH 23.7
Qadj = QL × = 127.6 × = 127.9-gpm
PL 23.6

We now show this flow as the flow through the second branch line and add the two flows to get the
total flow through the piece of pipe supplying the second branch line.
Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom lgth Pt 23.7
ftg Pf
Q 255.5 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Next comes the friction loss calculation for the flow from point B to point C.
This pipe is a piece of 4-inch schedule 10 10-feet long, which would yield the following friction loss
calculation:

4.52 × 255 .51.85 × 10

Pf =
1201.85 × 4.26 4.87
= 0.2-psi
Enter all of the pipe information and friction loss data in the worksheet.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we add the pressure at point B and the friction loss through the pipe supplying point B to get the
pressure at point C.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q Nom lgth Pt 23.9
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The pressure required to get our minimum end sprinkler conditions down our typical branch line was
calculated to be 23.6-psi at point A. But our pressure at point C is 23.9-psi. Our calculated flow for
our typical branch line was 127.6-gpm. We can use our formula to calculate the actual flow down our
third branch line based on the higher pressure.

PH 23.9
Qadj = QL × = 127.6 × = 128.4-gpm
PL 23.6
We now show this flow as the flow through the third branch line and add the two flows to get the total
flow through the piece of pipe supplying the third branch line.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom lgth Pt 23.9
ftg Pf
Q 383.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

By looking at our drawing, you will notice that we are past the last flowing sprinkler. There will be no
more flow additions for sprinklers. The remainder of the calculation is only for friction loss for a flow
of 383.9-gpm through the piping system down the cross main, through the riser and out to the
connection to the street.
Next we will calculate the friction loss from point C to the top of the riser, node TOR.
Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg Pf
Q 383.9 Act. 4.26
tot Pe
q Nom lgth Pt
ftg Pf
TOR Q 383.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The length of 4-inch schedule 10 pipe is 126’-0 ½”, or 126.04’ excluding fitting length. Enter this
value in the worksheet. Now we must enter the equivalent footage for the fittings in this run of pipe.
From node C to node TOR there are two elbows. In order to get our equivalent footage for these
fittings, we again reference Table 22.4.3.1.1. We will see the equivalent footage for one elbow is 10-
feet; therefore two elbows will equal 20-feet equivalent footage. However, we are not finished yet
because the title of the Table is “Equivalent Schedule 40 Steel Pipe Length Chart. Since we are using
schedule 10 pipe for the mains, we must make a modification to our equivalent footage number.
6

The formula for equivalent footage modifiers is found in NFPA-13, section 22.4.3.1.3 and is as
follows:

4.87
⎛ ActualInsideDiameter ⎞
Factor = ⎜⎜ ⎟⎟
⎝ Schedule40SteelPipeInsideDiameter ⎠

Which yields,

4.87
⎛ 4.26 ⎞
Factor = ⎜ ⎟ = 1.32
⎝ 4.026 ⎠

We now take our factor and multiply it times the 20-feet equivalency from the table to get:

20 x 1.32 = 26.3-feet or 26’-4” equivalent

Enter this into our worksheet.

6
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf
Q 383.9 Act. 4.26
tot 152-4 Pe
q Nom lgth Pt
ftg Pf
TOR Q 383.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The friction loss equation now becomes,

4.52 × 283 .91.85 × 152 .3

Pf =
1201.85 × 4.26 4.87
= 5.1-psi

Enter this in the worksheet.

 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom lgth Pt 29.0
ftg Pf
TOR Q 383.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Now we have the sprinkler system demand at the top of the riser. To get to the bottom of the riser we
add the pipe and fittings for the riser. The riser detail looks this way,
From our riser detail we see that from the TOR to the BOR we have 10’-6” of 6-inch schedule 10 pipe
and an alarm check valve.

Converting the 6-inch alarm check valve to equivalent feet requires a modifier just like the 4-inch
schedule 10. Table 22.4.3.1.1 gives us 32-feet,

Using the modifier equation we get:

4.87
⎛ 6.357 ⎞
Factor = ⎜ ⎟ = 1.257
⎝ 6.065 ⎠

We now take our factor and multiply it times the 32-feet equivalency from the table to get:

32 x 1.257 = 40.23-feet or 40’-3” equivalent

Enter this into our worksheet.

7
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf
TOR Q 383.9 Act. 6.357
tot 50-9 Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The friction loss equation now becomes,

4.52 × 383 .91.85 × 50 .75

Pf =
1201.85 × 6.357 4.87
= 0.2-psi

Enter this in the worksheet.

 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe
q Nom lgth Pt
ftg Pf
BOR Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Notice I have not added the friction loss to the total pressure yet. This is because there is one other
type of pressure that must be accounted for at this point. This is elevation pressure. You will notice
from the riser detail that the elevation difference between the TOR and BOR points is 11’-9”. As
water rises, it must overcome gravity. This type of pressure is calculated by an oft-used constant in
fire protection:

1-foot of elevation = 0.433-psi/ft of pressure.

For example, if a water tower is 100-feet tall what pressure will be present at the base? Using our
constant we get:

100-feet x 0.433-psi/ft = 43.3-psi.

In our example we have 11.75-feet of elevation from point TOR to BOR. This elevation pressure is:

11.75-feet x 0.433-psi/ft = 5.09-psi. Enter this in the worksheet.

Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe 5.1
q Nom lgth Pt 34.3
ftg Pf
BOR Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
TEST Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
The pressure demand at BOR is 34.3-psi. Now we can calculate the friction and elevation loss in the
underground piping. For this we will assume the underground is 100-feet long including a 4-foot drop
from the BOR point. We will also assume there is one gate valve in the piping and the piping is 6-inch
Class 52 ductile iron. With this information, our worksheet looks this way:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe 5.1
q Nom 6 lgth 100-0 Pt 34.3
E,T,G ftg 140 Pf
BOR Q 383.9 Act. 6.275
tot Pe
q Nom lgth Pt
ftg Pf
TEST Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

The internal diameter of 6-inch Class 52 ductile iron is taken from a resource on pipe sizes. The
fittings include the elbow at the bottom of the riser, the tee at the city connection and the valve at the
city connection. Notice the C-factor of ductile iron is 140. This is taken from NFPA-13, Table
22.4.4.7:
 8

To get the fitting equivalent footage, we take the values from Table 22.4.3.1.1

8
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety.
The total equivalent footage will be 14 + 30 + 3 = 47-feet. Again we must apply the diameter
modifier:

4.87
⎛ 6.275 ⎞
Factor = ⎜ ⎟ = 1.18
⎝ 6.065 ⎠
47 x 1.18 = 55.46-feet or 55’-6” equivalent. We cannot enter this into the worksheet yet however. For
this run of pipe we must make one more modification to the fitting equivalent footage. This will come
from NFPA-13, Table 22.4.3.2. Whenever your pipe C-value is other than 120, you must make an
adjustment to the equivalent footage you get from Table 22.4.3.1.1. Here is Table 22.4.3.2:

10

For a C-value of 140, we use multiplier of 1.33. We take our modified equivalent footage for diameter
and adjust it for C = 140:

55.46 x 1.33 = 73.76-feet or 73’-9” equivalent. We now enter this into our worksheet.

9
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy, MA
02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard in its
entirety.
10
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety
 Sprinkler Fittings & C- K-
Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe 5.1
q Nom 6 lgth 100-0 Pt 34.3
E,T,G ftg 73-9 140 Pf
BOR Q 383.9 Act. 6.275
tot 173-9 Pe
q Nom lgth Pt
ftg Pf
TEST Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

We now can calculate our friction loss as

4.52 × 383 .91.85 × 173 .75

Pf =
1401.85 × 6.275 4.87
= 0.7-psi

Also, don’t forget to include our estimated 4-foot elevation drop from the BOR to the underground
main: 4-feet x 0.433-psi/ft = 1.7-psi.
Enter these two values in the worksheet.

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe 5.1
q Nom 6 lgth 100-0 Pt 34.3
E,T,G ftg 73-9 140 Pf 0.7
BOR Q 383.9 Act. 6.275
tot 173-9 Pe 1.7
q Nom lgth Pt 36.7
ftg Pf
TEST Q 383.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

This gives us our sprinkler demand at the connection to the city main of 383.9-gpm at 36.7-psi. This is
not our final flow requirement since NFPA-13, section 11.1.4.2 states “The minimum water supply
requirements for a sprinkler system shall be determined by adding the hose stream allowance to
the water supply for sprinklers.” We have calculated the water supply requirements for the sprinkler
now we will add our hose allowance. The hose allowance simulates water taken from the water supply
by fire department operations in fighting the fire. Remember that our occupancy classification is
Ordinary Hazard Group 2. This will be required to determine our hose stream allowance from Table
11.2.3.1.2:

11

11
Reprinted with permission from NFPA 13-2007, Installation of Sprinkler Systems, Copyright © 2007, National Fire Protection Association, Quincy,
MA 02169. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only the standard
in its entirety
This makes our final demand requirements as follows:

Sprinkler Fittings & C- K-

Location
Flow (gpm) Pipe Size Pipe Equivalent Length psi/ft/ Req. Pressure
Devices factor factor
q Nom 1" lgth 10-0 Pt 7
None ftg 0-0 120 Pf 1.5 8
1 Q 21.2 Act. 1.049
tot 10-0 Pe 0
2 q 23.3 Nom 1 1/4" lgth 10-0 Pt 8.5
None ftg 0-0 120 Pf 1.5 8
Q 44.5 Act. 1.38
tot 10-0 Pe 0
3 q 25.3 Nom 1 1/2" lgth 10-0 Pt 10.0
None ftg 0-0 120 Pf 1.6 8
Q 69.8 Act. 1.61
tot 10-0 Pe 0
4 q 27.2 Nom 1 1/2" lgth 10-0 Pt 11.6
None ftg 0-0 120 Pf 3.0 8
Q 97.0 Act. 1.61
tot 10-0 Pe 0
5 q 30.6 Nom 1 1/2" lgth 10-0 Pt 14.6
T ftg 8-0 120 Pf 9.0 8
Q 127.6 Act. 1.61
tot 18-0 Pe 0
A q 0.0 Nom 4" lgth 10-0 Pt 23.6
None ftg 0-0 120 Pf 0.1
Q 127.6 Act. 4.26
tot 10-0 Pe 0
B q 127.9 Nom 4" lgth 10-0 Pt 23.7
None ftg 0-0 120 Pf 0.2
Q 255.5 Act. 4.26
tot 10-0 Pe 0
C q 128.4 Nom 4 lgth 126-0 1/2 Pt 23.9
2E ftg 26-4 120 Pf 5.1
Q 383.9 Act. 4.26
tot 152-4 Pe 0
q Nom 6 lgth 10-6 Pt 29.0
S ftg 40-3 120 Pf 0.2
TOR Q 383.9 Act. 6.357
tot 50-9 Pe 5.1
q Nom 6 lgth 100-0 Pt 34.3
E,T,G ftg 73-9 140 Pf 0.7
BOR Q 383.9 Act. 6.275
tot 173-9 Pe 1.7
q Nom lgth Pt 36.7
ftg Pf
TEST Q 383.9 Act.
tot Pe
HOSE q 250.0 Nom lgth Pt 36.7
ftg Pf
Q 633.9 Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe
q Nom lgth Pt
ftg Pf
Q Act.
tot Pe

Notice there is no additional pressure required for the hose allowance. It is simply added as flow since
the fire department will use the pump on the pumper truck to produce the pressure needed. The final
sprinkler demand requirements are:
633.9-gpm at 36.7-psi.
CONGRATULATIONS! YOU HAVE JUST COMPLETED MANUALLY CALCULATING THIS
FIRE SPRINKLER SYSTEM.

Summary
In this course you have learned the five basic types of occupancy classifications outlined in NFPA-13.
You have taken a sprinkler system and applied the two ways to determining the end sprinkler start
conditions when beginning a hydraulic calculation. You have applied the Hazen-Williams friction loss
formula to water flowing through a pipe and made flow adjustments to calculate the amount a typical
branch line will overflow due to higher pressure.