Service Manual

AKAI
27”/ 30” Wide Screen
LCD Multi-Media Display

LM-H27CJSA
LM-H30CJSA
 Table of Contents

1. Safety and Precautions …………………………………………………………1

2. Specifications.........................................................………………………………3
2.1 Specification for 27”............................……………………….…..3
2.2 Specification for 30”............................……………………….…..4
2.3 PC I/P Preset Timing Table.....................................................…..5
3. Connection & Applications……………………..............................................…..6
4. Controls Location ..........................................................................……………….8
5. Remote Control..............................................................................………………..9
6. Disassembly Instructions.......................…………………………….……..……..12
7. Block Diagram....................................................………………………………….18
8. Troubleshooting……………...............................................………………………19
8.1 Symptom Codes ( for Call center use). .............…………….…19
8.2 Flow Chart ( for Repair center use) ……….………....……….22
9. Electronic Circuit Description.....................................………………………..…27
10. Circuit Diagram...................................................…………………………..…….32
10.1 Main Board......................…………………….……………….32
10.2 Key , LED&IR Board .................……………………….…….42
10.3 Tuner Board…………………………………………………...43
10.4 I/O Board………………………………………………………44
11. PCB Layout...................................................…………………………………..…45
11.1 Main Board PCB.......……………………………..…………..45
11.2 Key , LED&IR Board PCB………..………………….…..….47
11.3 Tuner Board PCB……………………………………………..47
11.4 I/O Board PCB……………………………………………...…48
12. Electrical Parts List.....................................………………………………….…..49
13. Mechanical Disassembly....….............................................……………….……..57
14. Mechanical Parts List................................................……………………………59
 1. Safety and Precautions
CAUTION
* The service of this LCD TV must be carried out by qualified persons only.
* Do not change any module unless the set is switched off.

CLEANING：Always disconnect unit from mains supply before attempting to clean it.
Use soft cloth moistened with soapy water, wipe gently. Do not use
solvents of abrasive materials.

SOME DO’S AND DON’T’S ON THE SAFE USE OF EQUIPMENT

This equipment has been designed and manufactured to meet European

safety standards but like any electrical equipment, care must be taken if
you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (Including the mains plug, extension leads and
interconnections between pieces of equipment) are properly made in accordance with
the manufacturer’s instructions. Switch off and withdraw the mains plug when making
or changing connections.

Do use only the Power Cord and Power Supply (option) provided.

Do consult your dealer if you are ever in doubt of the installation, operating, or safety of
your equipment.

Don’t exert pressure on the LCD TV . This could break the panel .

Don’t continue to operate the equipment if you are in any doubt about it working
normally, or if it is damaged in any way. Switch off, withdraw the mains plug and consult
your dealer.

Don’t remove any fixed covers as this may expose dangerous voltages.

Don’t leave equipment switched on when it is unattended unless it is specifically stated

that it is designed for unattended operation or has a standby mode. Switch off using the
switch on the equipment and make sure that everyone knows how to do this. Special
arrangements may need to be made for infirm or handicapped people.

-1-
Don’t listen to headphones at high volume, as such use can permanently damage your
hearing.

Don’t obstruct the ventilation of the equipment, for example, with curtains or soft
furnishings. Overheating will cause damage and shorten the life of the equipment.

Don’t allow electrical equipment to be exposed to rain or moisture.

Above all

─ Never let anyone push anything into holes, slots or any other opening as this could
result in a fatal electric shock.
─ Never guess or take chances with electrical equipment of any kind.
─ It is better to be safe than sorry!

WARNING：TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS
HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT
OPEN THE CABINET. REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.

-2-
 2. Specifications
2.1 Specification for 27”:
ITEMS SPECIFICATION
Screen size 27” Wide TFT-LCD Panel (CMO)
Aspect Ratio 16：9
Resolution 1280 x 720 (Wide-XGA)
Contrast Ratio 500 : 1 (Typical)
Display
Brightness 500 cd/m² (Typical)
Viewing Angle 170° (Hor.) / 170° (Vert.)
Response Time : Ton / Toff 15ms / 10ms
OSD Language English, French, German, Spanish, Italian
TV Standard (CCIR) B/G, D/K, I and L/L’ (Multi-Europe)
Color System PAL / SECAM
TV Function
Sound System NICAM / A2 (IGR)
Teletext 10 Pages (FLOF / TOP )
Color System PAL / SECAM / NTSC
AV1 (In / Out) 21-pin SCART (RGB / Video) x1
Video (Composite) x1
Video I/O
S-Video x1
AV2 (In)
Component (YPbPr, YCbCr) x1
( DTV system : 625p)
Signal I/P Analog : D-Sub 15 pin (detachable cable)
PnP compatibility DDC / 2B
Analog: FH: 31kHz to 60kHz
PC I/P I/P Frequency
Fv: 56Hz to 75Hz
Recommended Analog: 1024x768 (60Hz)
DTV ready (via D-sub 15pin) DTV System : 625p
Speaker (Built-in) : 10W+10W (rms)
Headphone Mini-jack for stereo (3.5 mm)
Audio I/O Audio I/O: L/R PC audio in
Audio In 1 / Out (R/L)
Audio In 2 (R/L)
PIP under PC mode Yes
Other Functions A.P.S. , Child-Lock Yes
VESA Panel Wall Mounting Holes 100mm x 100mm
Power Supply AC 100V~240V, 50/60Hz
Power
Power Consumption < 140W
Panel Tilt Forwards/ Backwards /Rotation -5°/ +15° / ±180°
Weight (net) 14.5 Kg (Without Accessories)
Accessories Remote Control , Batteriesx2 , AC cord , D-Sub Signal Cable, Operation Manual .

-3-
2.2 Specification for 30” :

ITEMS SPECIFICATION
Screen size 30” Wide TFT-LCD Panel (CMO)
Aspect Ratio 16：9
Resolution 1280 x 768 (Wide-XGA)
Contrast Ratio 500 : 1 (Typical)
Display
Brightness 500 cd/m² (Typical)
Viewing Angle 170° (Hor.) / 170° (Vert.)
Response Time : Ton / Toff 15ms / 10ms
OSD Language English, French, German, Spanish, Italian
TV Standard (CCIR) B/G, D/K, I and L/L’ (Multi-Europe)
Color System PAL / SECAM
TV Function
Sound System NICAM / A2 (IGR)
Teletext 10 Pages (FLOF / TOP )
Color System PAL / SECAM / NTSC
AV1 (In / Out) 21-pin SCART (RGB / Video) x 1
Video (Composite) x1
Video I/O
S-Video x1
AV2 (In)
Component (YPbPr, YCbCr) x1
DTV system : 625p
Signal I/P Analog : D-Sub 15 pin (detachable cable)
PnP compatibility DDC / 2B
Analog: FH: 31kHz to 60kHz
PC I/P I/P Frequency
Fv: 56Hz to 75Hz
Recommended Analog: 1024x768 (60Hz)
DTV ready (via D-sub 15pin) DTV System : 625p
Speaker (Built-in) : 10W+10W (rms)
Headphone Mini-jack for stereo (3.5 mm)
AudioI/O Audio I/O: L/R PC audio in
Audio In 1 / Out (R/L)
Audio In 2 (R/L)
PIP under PC mode Yes
Other Functions A.P.S. , Child-Lock Yes
VESA Panel Wall Mounting Holes 100mm x 100mm
Power Supply AC 100V~240V, 50/60Hz
Power
Power Consumption < 150W
Panel Tilt Forwards/ Backwards /Rotation -5°/ +15° / ±180°
Weight (net) 15.2 Kg (Without Accessories)
Accessories Remote Control , Batteriesx2 , AC cord , D-Sub Signal Cable , Operation Manual .

-4-
2.3 PC I/P Preset Timing Table :

Analog Input
Pixel
Mode Name H.Freq. (kHz) H. Polarity
Mode No. CLK
Resolution V.Freq. (Hz) V. Polarity
(MHZ)
VGA 70Hz 31.469 +
1 25.175
640x350 70.087 -
VGA 60Hz 31.469 -
2 25.175
640x480 59.941 -
VGA 72Hz 37.861 -
3 31.5
640x480 72.81 -
VGA 75Hz 37.5 -
4 31.5
640x480 75.0 -
SVGA 56Hz 35.16 +
5 36.0
800x600 56.25 +
SVGA 60Hz 37.876 +
6 40.0
800x600 60.317 +
SVGA 72Hz 48.077 +
7 50.0
800x600 72.118 +
SVGA 75Hz 46.875 +
8 49.5
800x600 75.0 +
XGA 60Hz 48.363 -
9 65.0
1024x768 60.004 -
XGA 70Hz 56.476 -
10 75.0
1024x768 70.069 -
XGA 75Hz 60.023 +
11 78.75
1024x768 75.029 +
MAC VGA 35.0 -
12 30.24
640x480 66.667 -
MAC VGA 49.725 -
13 57.283
832x624 74.550 -
US TEXT 31.469 -
14 28.322
720x400 70.087 +
WXGA 60Hz 47.733 -
15 80
1280x768 60.042 -

-5-
 3. Connection ＆ Applications

SCART
VIDEO
S-VIDEO
Y
Component Pb/Cb
Pr /Cr

AC IN

-6-
 D-SUB CONNECTOR
PC AUDIO IN
HEAD PHONE
AUDIO IN 1 / OUT(R/L)
AUDIO IN 2 (R/L)
75Ohm AERIAL
INPUT SOCKET

PC

HEAD PHONE

SPEAKERS

VIDEO

AERIAL

NOTE:

z Audio out : The level of audio output cannot be changed using the volume , treble , and bass controls
on your TV . These connectors should be used with an external audio amplifier that can
be used to control the volume.
z VCR Recording: The main display must set to TV mode in order to use SCART to record a program using
a VCR .
z PIP sound : When using the PIP feature in PC mode , to hear the Sub display sound you must set the
sound source to “Sub” .

-7-
 4. Controls Location
The buttons control your TV’s basic features, including the on-screen menu. To use the more
advanced features, you must use the remote control.

POWER: turn on or turn off the LCD TV.

SOURCE: set up the input source (PC, TV, SCART Video/ SCART RGB ,
Video, S-Video, Component)
MENU: display the main menu.
CHANNEL (down/up): change channels.
VOLUME (-/+): turn up or turn down the volume.
ASPECT RATIO: set up the ratio of display (Normal, Panscan, Zoom or Full.)

ASPECT RATIO VOLUME(-/+ ) CHANNEL(down/up) MENU SOURCE POWER

Speaker Speaker

Remote sensor window Power indicator

Aim the remote control A green indicator lights when the power is on
towards this region on the and a red indicator lights when in the standby
TV. mode (the indicator will not light when the main
power is off).

-8-
 5. Remote Control
The remote control pad works almost same as ordinary TV remote control that includes the
basic function needed while viewing a live video.

DISPLAY : Display the current source or program digits .

-9-
Summary of Control Buttons

Selecting the Signal Source

TV Switch to the TV mode.
PC Switch to the PC mode.
SCART Switch to the Video mode or RGB mode from SCART.
VIDEO/S-V Switch to the Video mode from RCA socket or S-Video mode.
COMPONENT Switch to the Component mode (YPbPr or YCbCr).
DISPLAY Display the current source.

Menu Setting
MENU/ENTER Display the main on-screen menu or enter the next menu.
UP/DOWN Press to select the item you want to adjust in the OSD menu.
VOL- / VOL+ Press to decrease or increase the value in the OSD control bar.
EXIT Exit from the menu.

Changing Channels
P- / P+ Press P- or P+ to change Programs in TV mode or Teletext page in
TELETEXT mode.
0~9 To select programs directly in TV mode.
DISPLAY Display the current program digits.
RTN Press to return to the previous program.

Sound Control
VOL+ / VOL- Press to turn up or turn down the volume.
MUTE Press to switch the sound on or off.
SOUND Press to choose Stereo, Bilingual and Monaural broadcasts.

Teletext Control
TELETEXT Press to show the Teletext Service. Press again to return to TV Viewing.

INDEX Press “ INDEX“ button to show the list of teletext contents.

HOLD Press “ HOLD“ button to stop the automatic page change.

UPDATE Press “ UPDATE“ button to switch to TV while waiting for the next text page.

-10-
 REVEAL Press “REVEAL“ button to display concealed information, such as
solutions of riddles or a quiz.
EXPAND Press “EXPAND“ button to enlarge the top half or bottom half of the
Teletext page.
SUB-PAGE/TIME Press “SUB-PAGE/TIME“ button to access to the sub-page you
required.

RTN Press to return to the previous viewed Teletext page.

PIP Control
ON / OFF Press to watch one of the video sources on Sub-display, whilst in
PC mode. Press again to turn off the Sub-display.

PIP Source Press to select the PIP window input source as :

Press ▲ button : TV→ SCART Video→SCART RGB→ Video→
S-Video→ Component
Press ▼ button : Component→ S-Video → Video→ SCART RGB
→SCART Video→ TV

SIZE To make the PIP window double, large or small.

POSITION Press to move the PIP window to: Top Left → Top Right→
Bottom Right → Bottom Left → Repeat.

NOTE : When you set Main-display at 1280x768/1024x768 resolution of PC mode and Sub-display
YPbPr, the screen will appear “Not Available“. You should reduce the PC resolution to 800 X
600 or 640 X 480. The PIP function will then work.

Other Function

RESET Reset to the original factory settings, such as theBrightness/Contrast/

Color Temp.

Set the picture window to Normal(4:3) → Panscan→ Zoom→ Full

ARC
(16:9)

APC To select Clear,Dark, or Nomal mode for picture control.

SLEEP Press to select a preset time interval for automatic power off .

SUB-PAGE/TIME Press “Sub-Page/Time“ to display the digital clock in TV mode.

-11-
 6. Disassembly Instructions
1. Face down the LCD-TV :
Face down the LCD-TV on a smooth plane with a soft material to protect the panel
faceplate .

2. Tuner Board Removal :

Note: If only repair the Tuner Board , need not disassemble the
Base and Back Cover.
2.1 Remove Tuner Cover by pressing point D’ and pushing point D toward the
right direction. ( Indicated as “D”and “ D’ ” )
2.2 Remove 1 screw from the Tuner Board and pull out it along the slot .
( Indicated as “D’’ ”)

D’

D’’

-12-
3. Base Removal :
3.1 Remove 5 screws from the bottom of the Base. (Indicated as “A ”)
3.2 Push upward and take the Base apart from the Neck. (Indicated as “Arrow” )

4. Neck Removal :
4.1 Remove 2 screws from Neck Cover. (Indicated as “B ” )
4.2 Push 2 hooks on the inside of the Neck Cover by screw driver and take the Neck Cover
apart from the Neck . (Indicated as “B’ ” )

B’ B’

-13-
 4.3 Remove 4 screws from the Neck and then take Neck apart from the Back Cover.
(Indicated as “ C ”)

5. AV Cover (I/O Board) Removal :

5.1 Loosen 2 screws. ( Indicated as “ E ”)
5.2 Pull out the AV Cover (I/O Board) directly. ( Indicated as “ Arrow ”)

-14-
6. Back Cover Removal:
6.1 Remove 8 screws from the Back Cover . ( Indicated as “ F ” and “G”)
6.2 Take Back Cover apart from the LCD-TV.

7. Right / Left Side Covers Removal :

7.1 Remove 4 screws from 2 Slides of I/O Board & Right Side Cover. (Indicated as “ H ”)
7.2 Remove 3 screws from the Power Case Assembly. (Indicated as “ J ”)
7.3 Pull out the Power Case Assembly downwards. (Indicated as “ Arrow”)

-15-
8. Main PCB Shield Removal :
8.1 Remove 2 screws from Main PCB Shield. (Indicated as “ K ” )
8.2 Remove 2 Hexagonal screws from the D-Sub Connector. (Indicated as “K’ ”)
8.3 Take Main PCB Shield apart from Panel Bracket .

K’

9. Main Bracket Removal :

9.1 Remove 8 screws from the Main PCB . (Indicated “ L “)
9.2 Take Main PCB apart from the Main Bracket .

-16-
10. Panel Bracket Removal :

10.1 Remove 5 screws from the Panel Bracket . (Indicated as “ M ”)

10.2 Take Panel Bracket apart from the Front Cover .

-17-
 7. Block Diagram 10W + 10W
I021 Speaker
UT01 I044 Audio Amp.
SIF Headphone Jack
TV – Tuner Mono TV 4:1 Audio Processor LA4282
FQ1216 MK3 MSP3410G Scart Audio Out
Video Scart Audio Component
Video/S-V/ Component Audio I034 Line-out (RCA)
PC Audio Audio Out P15V330
I011
TT Decorder
SAA5264PS
LCD
I019 Panel
Scart-Video I018
8 bit Scaler I014 16:9
Video Decorder TP6760 LVDS
S-Video SAA7118E
Scart-RGB
I010
Interlace P15V330
Component I006
24 bit Port B
Progressive ADC
AD9883-110

I001 24 bit Port A

PC VGA ADC INVERTER
AD9883-140

Remote Control LED & IR Pad I012

AC Input MCU
Key Pad SM59264C40
100~240V
Power + 24V (SyncMOS)
50 / 60Hz + 5V I013
Module + 2.5V EEPROM: 24C16
+ 3.3V

-18-
 8. Troubleshooting
8.1 Symptom Codes : ( for Call Center use )
CODE SYMPTOM COUNTERMEASURES
NP1 No Picture and No Sound • Make sure the Power cord and Aerial Cable are
in TV mode. properly connected .
• Make sure the batteries in remote control are not flat.
No picture and and no Sound

• Press the POWER button to switch the TV on.

• Switch to TV source by pressing “TV” button.
• Run “Automatic Search ” by operating the remote
control.
NP2 No Picture and No Sound • Check the connection between the optional video
in video mode. equipment and the TV.
• Press SCART , Video/S-V or COMPONENT button
on the remote control to select the right video
equipment.
NP3 TV is automatically turned • Check if the “SLEEP” timer is activated .
off. • Press the POWER button to turn on the TV once
again.
PP1 Double Images / Ghosts If the TV suffers interference from signals reflecting from
mountains or buildings , double-pictures or Ghosts will
occur.
• Adjust the aerial’s location and direction
• Replace it with one with better directionality.
• Turn off or disconnect the booster if it is in use , as
the booster may be inappropriate.
PP2 Snowy picture and noisy If snow totally blocks out the picture , there may be a
Sound problem with the Aerial or Aerial Cable .
• Have the TV and aerial been connected properly ?
Poor Picture

Has the aerial cable been damaged ?

• Is the aerial pointing in the right direction ?
• Is the aerial itself faulty ?
• Try using a booster , as signal transmission may be
low.
PP3 Distorted picture and • Turn off or disconnected the booster if it is in use , as
noisy sound broadcast signals may be too strong.
PP4 Dotted Lines / Stripes If the TV or aerial suffers interference from other
in the picture. equipment , stripes or noise may appear in the picture.
• Keep the TV away from noise sources such as
personal computer , amplifier , cars, motorcycles or
hair-dryers.
• If the aerial suffers interference from a radio tower or
high-voltage wire , contact the local dealer.

-19-
 CODE SYMPTOM COUNTERMEASURES
PP5 Stripe noise . • Check the coaxial cable connected with the TV is not
oxidized
• Do not use 300 ohm twin lead cables as interference
Poor Picture

may occur
• It is recommended to use a 75 ohm coaxial cable (not
supplied) to get premium quality picture.
• Keep the aerial cable away from other connecting
cables.
PP6 No color, too light or too • Adjust the picture settings — APC, Brightness,
dark Contrast, Saturation , Color Temp.
• Press “RESET ” button on remote control .
NS1 Good picture, no sound • Make sure the headphone is not connected.
• Check audio connections between Equipment &
LCD-TV.
• Press MUTE or VOL + to cancel the muting.

NS2 Noisy noise • Make sure that the aerial connected is 75 ohm coaxial
cable (not supplied) , not 300 ohm twin lead cables .
• Keep the aerial cable away from other connecting
cables.
• Press SOUND to select “Mono” which will reduce
the noise.
No Sound or Noisy Sound

• Adjust BASS or TREBLE properly in OSD.

NS3 No sound in TV mode If the Country setting for the TV is incorrect , it may
prevent the sound from being issued
• Select the Country where you are located in OSD
Menu.
• If the country is not listed in OSD , select “Other
Country” .

NS4 Good picture, but noisy • If the sound of “all the channels” is noisy , run
sound or no sound in TV A.P.S. again by selecting Automatic Search in OSD.
mode.
• If the sound of “some channels” is noisy or no
sound , select Manual Search and select an
appropriate TV system in OSD such as B/G , D/K ,
I , L/L’ ; then , store it.

( If the sound system setting for a TV channel is

incorrect , it may prevent the sound from being issued .)
PC1 PC display is Not Full • Select Auto Image Adjust in OSD menu to optimize
Screen the image .
• If executing Auto Image Adjust still can not achieve
full screen display, adjust V.Position and H.Position
PC

in PC mode
PC2 Horizontal Noise or Color • Select Auto Image Adjust in OSD menu to optimize
pattern is not uniform the image .
• If still no good , adjust H. Phase in OSD menu

-20-
 CODE SYMPTOM COUNTERMEASURES
PC3 “Out of Range” message • Maximum PC resolution supported is 1024x768 /
1280 x 768, so the screen will appear “Out of range”
at higher resolution.
• Reduce the resolution to 1024x 768/ 1280x 768 from
PC .
PC4 No Sound • Make sure PC audio Input is well connected.
PC5 “Not Available” message • If Main-Display is PC and Sub-display is
on PIP Component , resolution of the PC should be reduced
PC

to 800 x 600 or lower ;then , the PIP will work well.

PC6 After “No Signal ” has • Press any key on keyboard or move the mouse to
appeared on PC mode for a activate the PC , because the PC may go to power
while, the view disappears saving status.
and the “ LED Indicator” • Check if the D-sub connector (Cable) is disconnected
turns from Green or loose .
to”Red” .
RC1 Remote Control does not • Make sure the batteries in remote control are not flat
work • Check the polarity of the batteries
• Use the remote control in the front of the TV or from
Remote Control

less than seven meters away.

• make sure the Remote Sensor Window is not under
strong lighting.

RC2 Can not change channels • Press TV button to switch to TV mode.

with the remote control • Make sure the TV is not in Teletext mode.

PH1 Picture suddenly Stops • Press RESET button on remote control .

Responding or abnormal. • Unplug and then plug the Power Cord of the TV
from the AC outlet (or the Adapter from the TV).
• If the picture still no good , execute “Initial
Picture Halt / Abnormal

EEPROM”.

Press POWER key to turn off the TV . Press“CH∇ ” key

on the top of LCD TV ( don’t release ) ; then, press
POWER button on remote control until “Initial
EEPROM” appears on the screen .

(Note : Remind user that every setting will be return to

factory preset mode including Child Lock , PIN No. ,
Programs …)

-21-
8.2 Flow Chart : ( for Repair Center Use )

(1) Power Start NG

No Backlight
& No LED

Is the Voltage of
P803#10 5V & No Replace PB01
P803# 4 24V ? (Power Module)
(on Power Module)

Yes

Is the Voltage of
L139 24V ? No Check connectors
(on Main Board) P803 & P019 .

Yes

Is the Voltage of No Check connectors

L104 5V? P803 & P019 .
(on Main Board)
Yes
Is the Voltage of No Replace I016
I016 #2
3.3V?
Yes

Is the Voltage of No Replace I015

I015 #2
2.5V?
Yes

Check and Re-plug wires

P015A (from LED Board to P015)
and P802A (from Inverter to P802) .

-22-
(2) No Backlight , but LED lights up

No Backlight ,but
LED lights up

Still No
Replace backlight Which Color does
Check & Re-plug Green
U901 (Inverter) LED
or P802 & P802A Display ?
( from Power to
I019 (Scaler) Inverter)
Red

Press POWER key & Is it entering into

Reset the MCU(I012) by
AC
Re-plugthe
pressing Power
power key Cord to
No Power Saving on
orreset I012 (MCU)
re-plugging .
the DC PC mode ?
12V cable.
Picture
shows Yes
Still no
Restart Signal to
Picture ensure
RestartH.Signal
V. sync.
to
I012 (MCU) hangs are H.
ensure not V. sync.
absent
temporarily . are not absent

Replace
Replace I012
I012 (MCU )

End End End

-23-
(3) No picture , but Backlight & LED light up

No Picture , but
Backlight & LED
light Up

Is the Voltage of
L042 5V No Replace
(Panel 5V I/P) ? Q003/I027/L095

Yes

Do all of the No No Replace

Does PC have
sources have No I001
picture?
Picture ? AD9883-140

Yes
Yes

Replace Do Scart /Video/ No Replace

I019 S-Video I018
(TP6760) have pictures? SAA7118

Yes

Does Component
have picture?

No
Still No
After replacing Picture
I006 AD9883-110 ,
does Component
have picture ?

Yes

End End End

-24-
(4) Picture Abnormal or Halt

Picture
Abnormal
/ Halt
Steps to Refresh EEPROM :
StepsM
After pressing
RESET Yes 1. Press POWER key to turn off
button ,does the the LCD-TV.
picture recover
normal?
2. Press CH. Down key on the
No top of LCD-TV (don’t release )
Yes and then press POWER
After pressing button on remote control, until
POWER OFF /
“EEPROM Initial” appears.
ON , does the
picture recover
normal ? 3. Now, all the buttons which you
No are pressing could be loosed .
Yes
After re-plugging
Power Cord
,does the picture
recover normal?

No

Refresh
EEPROM
(Refer to the right side)

End End

Note : If the PIN of Child-Lock is forgotten , the only way to unlock the channels is to
refresh EEPROM and the PIN will also recover initial number “1111”. Besides , all the
STORE done by user will be refreshed to the situation of First Time Installation.

-25-
(5) Frame Defects or Striped Lines at all sources

The Ver. or Hor.

Sync. haven’t been
held at all sources.

Are the Outputs of Does the wire

Does the wire
I019 (TP6760) Yes P005A connect Yes P005A connect Yes
normal ? firmly with LCD Replace V901
firmly to P005 ? (LCD Panel )
( SHFCLK,PVSync, Panel ?
PHSync,PDE)
No No No

Are the input

Connect of P005A Connect the wire
waveforms of End
firmly to P005. firmly with the
I019 normal ? Interface of Panel.
Yes

Replace I019
( TP6760 ) End End

End

-26-
 9. Electronic Circuit Description

9.1 Main Board Circuit

1) Power
Refer to sheet 7 of PWB-0663 circuit diagram.
AC 110V~220V is applied to the LCD-TV through socket P801 on PB01 (Power
module: PWB-0656) . PB01 (Power module: PWB-0656) outputs DC+24V to Inverter
U901 via P802#1~#5 . DC+24V is also applied to Main Board via P803#4 and then
fed directly to I010#10 (Audio Amp. LA4282).
PB01 (Power module) also provides +5V to Main Board via P803#10. It is
applied to I044 (Audio processor MSP3410) through L031. +5V is also applied to
Panel through L095 , I027 ( MOSFET: MI9933) ,L042 and connector P005 #19.
Beside, +5V is regulated by I016 (switching regulator : LT1084) to provide
+3.3V and also regulated by I015 (switching regulator : LT1117-adj) to provide
+2.5V for all chips.

2) PC Signal
Refer to sheet 1 of PWB-0663 circuit diagram.
The analog R.G.B. video signals are supplied through the PJ03( D-sub connector)
and these three input signals are approximately 0.7Vpp in amplitude. R031、R032and
R033 give resistance of 75Ωrespectively for impedance matching. These R.G.B.
video signals are AC coupled via 0.047U capacitors C021、C016 and C013, and then
fed into the I001 (AD converter) at #54、#48、#49 and #43 respectively. Then , R.G.B.
video signals are converted to their digital forms in I001. The outputs of digital data
including 8 bits red, 8 bits green, 8 bits blue signals are assigned at #70~77、#2~9and
#12~19 of I001, and applied to port A of I019 (Scaler : TP6760) . H.sync & V.sync
are applied to I001 #30、#31 and the processed signal taken from #66、#64 are fed into
I019 (TP6760) #18、#19. CLK signal is taken from I001 (AD9883-140) #67 and
applied to I019 (TP6760) #156. The LCD-TV is designed to have the DDC/2B
functions. DDC communication between the LCD-TV and computer is via PJ03
(D-sub connector ) #12、#15 and I004 #5、#6. The EDID data have written into the
I004 (EEPROM) in the factory during production , so computer will read out the
EDID from the I004 (EEPROM).

-27-
3) TV Signal

Refer to sheet 4、8、9 of PWB-0663 circuit diagrams.

The IEC plug on tuner UT01 receives TV picture and Sound signals from
aerial .Tuner UT01(Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR
B/G, D/K, I, L/L’ system and the front-end has a built-in digitally (I2C) PLL tuning
system . (Refer to Chapter 9.2 Tuner Board Circuit)

Tuner UT01 provides the Composite Video at QT01 #Emitter and is connected
to I018(SAA7118)L3 via P030#1 , and then provides at output #M1of
I018(SAA7118) . Then , it is connected to Teletext Decorder I011 (SAA5264) #23
and provides at the R.G.B. output of I011#34、#33、#32 after processing. These 3
decorded R.G.B. signal are delivered back to I018(SAA7118) # E1、#J3、#G1 .

AF and SIF sound from UT01 (Tuner) are applied to Audio Processor I044
(MSP3410) #47、#50 through golden fingerPT01 #27，28、#25，26 and P019 #15,#17
on main Board.

4) AV Signal

(A) Video / S-Video / Component (480i , 525i , 625i):

Refer to sheet 9 of PWB-0663 circuit diagrams.
Video decorder I018 (SAA7118) is able to decode the colour of PAL , SECAM ,
and NTSC signals into ITU 601 compatible colour component values . It accepts
4 different video signals, including Composite Video ( CVBS)、S-Video(Y/C
Signal)、SCART-R.G.B. and Component Video . There are 4 A/D Converters at
the I/O port of I018 (SAA7118) which includes 16 channel analog inputs.

I018 (SAA7118) 16 channel analog inputs accept Video/S-Video/Component

signals from PI01 / PI08/ PI10 / PI02,PI03,PI04 and provides at the output of 8
bits X-port and then connected to Port V of Scaler I019 #143~#150 .
(B) Component (480p , 525p , 625p) :
Refer to sheet 2 of PWB-0663 circuit diagrams.
Component Signals Y PbPr are applied to I006 (AD9883-110) # 43,48,49,54
through Green/Blue/Red connectors PI02/PI03/PI04 . I006 , AD Converter,
converts YPbPr signals to its 24bits digital format and is connected to Port B of
Scaler I019 #8~15、#198~205、#175~182.

-28-
5) Panel interface

Refer to sheet 6 of PWB-0663 circuit diagrams.

The signals of panel interface are all applied from Scaler I019(TP6760) to LCD
Panel through connector P005 and wire P005A. The signals CLK、DE、V.SYNC、
H.SYNC from I019 #90,#92~94 are applied to LVDS IC I014 #31,#30,#28,#27 and
output PCLK-,PCLK+ at #39,#40 .Then , signals are applied to Panel via connector
P005 #7, #6 and used for panel display controls. The 24 bits digital R.G.B.data from
data outputs of I019 (Scaler) are transformed to LVDS signals through I014 and then
applied to 8 bits LCD panel .
+5V for LCD panel is controlled by I019 #96 (FPVCC) via Q003(MTB3904)
and I027 (MM9933)

6) MCU

Refer to sheet 5 of PWB-0663 circuit diagrams.

* Pin 21 (UCLK): The Microcontroller I012 (Sync.Mos: SM59264C) is operated with
the 14.318 MHz Clock which is provided from Scaler I019 #136 (UCLK) based on
crystal X002.

* Pin 10 (Reset ) : C127 and R096 constitute a Reset circuit. It provides a necessary
active high reset signal to I012(MCU) # 10 for proper operation of I012.

* Pin 15 (IR ) : The signal IR_DA at I012 #15 is connect with Infrared Receiver. If the
IR receives some signal, I012 will send interrupt signal via I012 #2、#3 ( MSDA、
MSCL) to control other chips .

* Pin 36~43 (Data transfer): The signals AD0~ AD7 transferring between
I012(MCU)and I019 (Scaler) are assigned to I012 #36~#43.

* Pin 11,13 (Debug) : The signals TXD and RXD used for debugging firmware are
assigned to I012 #13、11.

I013 (24LC16B) provides necessary non-volatile storage for operating variables

and parameters. It is controlled by I012 via MSDA and MSCL signal, which are pull
up to +5V voltage by R092 and R093 (10KΩ).

-29-
9.2 Tuner Board Circuit
Refer to Tuner Board circuit diagrams of PWB-0564 in Chapter 10.3.
UT01(Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR B/G, D/K, I,
L/L’ system and the front-end has a built-in digitally (I2C) PLL tuning system . The
Output of Composite Video from QT01 #Emitter fed with Tuner UT01 is applied to
SAA7118 through PT01#23、24(Golden Finger) , wire P030A and socket P030#1 on
Main Board.
AF and SIF sound from UT01 (Tuner) are applied to Audio Processor I044
( MSP3410) #47、#50 through Golden Finger PT01 #27，28、#25，26 and P019#15, #17on
Main Board. The specifications of Tuner are as follows :

Intermediate Frequencies
System L L’ B/G D/K I
Picture Carrier 38.90 33.95 38.90 38.90 38.90
Colour 34.47 38.38 34.47 34.47 34.47
Sound 1 32.40 40.40 33.40 32.40 32.90
Sound 2 - - 33.16 - -
NICAM 33.05 39.80 33.05 33.05 32.348

Channel Coverage
BAND Frequency (MHz)
Low Band 48.25 to 160.00MHz
Mis Band 160.00 to 442.00 MHz
High Band 442.00 to 863.25 MHz

PINNING
SYMBOL PIN DESCRIPTION
N.C. 1 (AGC Monitor) Do not connect *
N.C. 2 (Tuning Voltage Monitor ) Do not connect
+5V 3 Supply Voltage Vb , tuner section.
SCL 4 I2C – serial Clock
SDA 5 I2C – serial Data
AS 6 I2C – Address Select
- X
- X
N.C. 9 Not connected
N.C. 10 Not connected
2nd IF Sound 11 Second IF sound output
CVBS 12 Composite Video Baseband Signal
+5V , IF 13 Supply Voltage , IF section
AF O/P (TV) 14 AF sound output
Ground Mounting Tags

-30-
9.3 Key、LED&IR Board Circuit
Refer to Key、LED & IR circuit diagram of PWB-0565 in Chapter10.2 and sheet 5
of PWB-0663 circuit diagram(Main Board).

* Key : The Keyboard is connected with Main Board through socket P021 and wire
P021A and to control the I012 (MCU) .So , if the operation of key is fail , the I012
(MCU) may fail .

* IR : The IR01 (PL-IRM0101-3) is a receiver for infrared remote control systems.

The demodulated output signal can directly be decoded by MCU I012#15 through
P015#6 and wire P015A .

* LED :The dual LED D601 on LED&IR Board is controlled by MCU I012 #24、#25
through P015 #2、#3 and wire P015A.

9.4 Inverter Board Circuit

The Inverter Board is fed with +24V through socket P802 #1~5 on PB01 (Power
Module:PWB-0656 )and wire P802A .It offers 4.5mA (typical ) to each lamp of
backlight in LCD panel. (30” panel :16Lamps , 27” panel :14 Lamps)
The On / Off of the inverter is controlled by the voltage of P802 # 11 which is
applied from I019 (Scaler:TP6760) #95 (FPBACK) via P019#1 on Main Board.
While the voltage of P802 #11 is ‘H’(2~3.3V) , the lamp of backlight will be turned
on. While the voltage of P802 # 11 is ‘L’ (0~ 0.8V) , the lamp of backlight will be
turned off.
Adjusting the Brightness in OSD menu is to control the voltage at #62 (DVD0) of
I019 (Scaler:TP6760) and then applies to P019#2 on Main Board and P802 #12 to
Inverter . The range of the voltage is from 0V to 2.7V. If the voltage of P802#12 is
0V, the screen will get light ; if it’s 2.7V, the screen will get dim. It means that the
different voltage will change the lamp current through the inverter to make the screen
lighter or dimmer.

-31-
 10. Circuit Diagram
10.1 Main Board (PWB-0663)

-32-
-33-
-34-
-35-
-36-
-37-
-38-
-39-
-40-
-41-
10.2 Key , LED&IR Board (PWB-0565)

-42-
10.3 Tuner Board (PWB-0564)

-43-
10.3 I/O Board (PWB-0638)

-44-
 11. PCB Layout
11.1 Main Board PCB (PWB-0663) :

-45-
-46-
11.2 Key , LED&IR Board PCB (PWB-0565)

11.3 Tuner Board PCB (PWB-0564)

-47-
11.4 I/O Board PCB (PWB-0638)

-48-
 12. Electrical Parts List
12.1 Main Board ( PWB-0663 )

Main PCB / MCU / Dip Parts

Item pc’s Circuit No. Part Spec. Part No AVL
1 1 U0663 PCB : PWB-0663 5053106630 TKE
2 1 I012 MCU : SM59264C 6647021813 Sync.MOS.
3 1 C559 470U/35V 5213547112 CAPXON
4 2 C560,C566 1000U/25V 5214021401 CHINSAN
5 1 I011 SAA5264 6645006603 PHILIPS
6 1 P007 Ear Phone: JY-3551-21 5056302037 Lih-Sheng
7 1 PJ04 PC-AUDIO Jack (B) 5056300104 S.C
8 1 PJ03 D-SUB Connector 5056309125 Cen-Link
9 2 P014,P006 RCA JACK (RED) 5056302039
S.C
10 2 P013,P024 RCA JACK (WHITE) 5056302054
11 1 P030 CON 2P W 5056415228 JST
12 1 PJ11 CON 4P W 5056415484 Leoco
13 1 P015 CON 6P W 5056415685 Leoco
14 2 P001,P021 CON 10P W 5056416038 JST,JWT
15 1 P003 CON 10P L 5056416023 JST
16 1 P016 Test Pin (4P) 5056415475 JST,JWT
17 1 X001 24.576MHz / 22pF 6699134506
18 1 X002 14.318MHz / 30pF 6699106034
H.ELE
19 1 X008 18.432MHz / 12pF 6699153730
20 1 X003 12MHz / 18p 6699114105
21 2 L002,L093 100uH / Coil Peaking 5064410129 TDK,CHILISIN
22 1 P019 PS-D01(20P) 5056416009
Cen-Link
23 1 P050 SLOT-30P Connector 5056301519
24 1 R150 3W / 470Ω 5130547103 TZAI YUAN
25 1 I021 LA4282 6644011200 SANYO
26 1 Q001 HTIP42C , PNP 6624003700 HSMC

-49-
 Main Board SMD Parts
Item pc’s Circuit No. Part Spec. Part No Type
C035,C127,C284,C527,C532,
1 6 4.7U/16V 5218014791 SMD
C558
C003,C004,C005,C006,C007,
C008,C009,C010,C011,C012,
C014,C015,C017,C019,C020,
C022,C023,C024,C025,C027,
C028,C030,C034,C036,C042,
C046,C049,C050,C051,C052,
C053,C054,C055,C056,C057,
C060,C061,C063,C065,C066,
C067,C068,C069,C070,C073,
C075,C078,C080,C082,C083,
C084,C126,C128,C192,C200,
2 111 C202,C212,C218,C220,C222, 0.1U / 25V 5230005491 0603
C223,C224,C226,C227,C228,
C229,C230,C236,C237,C238,
C241,C249,C251,C253,C254,
C255,C262,C263,C264,C265,
C266,C267,C268,C271,C272,
C275,C276,C277,C278,C280,
C281,C290,C291,C292,C293,
C294,C295,C319,C323,C326,
C504,C514,C524,C549,C550,
C086,C087,C088,C247,C436,
C437
C026,C029,C032,C033,C071,
C074,C076,C077,C194,C195,
C197,C198,C199,C203,C204,
3 31 C205,C213,C225,C256,C273, 10U/16V 5218007891 SMD
C274,C279,C324,C325,C456,
C506,C511,C526,C528,C552,
C553.
C018,C047,C048,C058,C062,
4 10 1000P/50V 5230610291 0603
C064,C072,C085,C513,C525
C013,C016,C021,C059,C234,
C246,C248,C250,C252,C258,
5 23 C259,C261,C377,C378,C379, 0.047U/50V 5230647391 0603
C131,C132,C133,C134,C135,
C136,C137,C191
6 2 C522,C534 1U/16V 5230001191 0805
C095,C096,C118,C119,C121,
7 8 2.2U/16V 5230007791 0805
C130,C300,C301
C503,C507,C508,C509,C510,
8 9 0.33U/16V 5230004191 0603
C517,C523,C529,C530
9 2 C537,C541 5P / 50V 5240605091 0603
10 1 C433 220P / 50V 5240622191 0603

-50-
Item pc’s Circuit No. Part Spec. Part No Type
C138,C139,C140,C338,C337,
C341,C342,C363,C364,C368,
C369,C370,C371,C372,C373,
C374,C375,C376,C380,C381,
11 34 330P 5240633191 0603
C382,C521,C516,C533,C515,
C505,C535,C512,C536,C563,
C562,C567,C568,C572,C571,
C564,C565,C569,C570
12 2 C001,C044 0.0082U/50V 5230682291 0603
13 2 C002,C045 0.082U 5230019091 0603
14 4 C201,C548,C555,C561 100U/16V 5218007991 SMD 6x5
C031,C079,C146,C147,C148,
C149,C154,C155,C156,C157,
C163,C164,C165,C166,C171,
15 33 C172,C173,C174,C179,C180, 27P/50V 5240627091 0603
C181,C182,C187,C188,C189,
C190,C282,C283,C285,C286,
C287,C288,C289
16 3 C038,C129,C260 100P/50V 5240610191 0603

17 4 C196,C206,C210,C211 0.01U/50V 5230610391 0603

18 1 C556 0.15U 5230019191 0603

19 2 C501,C502 22U/16V 5218008891 SMD

20 3 C214,C219,C432 47U/16V 5218008991 SMD

21 2 C232,C233 22p/50V 5240622091 0603

22 4 C235,C245,C543,C554 56P 5240656091 0603

23 1 C546 470P/50V 5240647191 0603
24 2 C518,C519 4700P 5230647291 0603

25 2 C037,C089 47P 5240647091 0603

D001,D002,D003,D038,D039,
BAV99 (DII) 6613000555
26 11 D040,D041,D045,D046,D047, SOT-23
MMBD7000LT1 (ON) 6613003550
D048
LS4148 (Rohm) 6613003059
27 3 D004,D005,D036 0805
HSK120 (HIT) 6613003052
28 1 D006 BZT52C2V4-7 (DII) 6615026753
RP07,RP08,RP09,RP10,RP11,
29 8 RP100x4 5160310900 Array x 4
RP12,RP19,RP20

30 4 L123,L139,L140,L141 0 5132300009 0805

L021,L024,L025,L026,L029,
31 8 FBM-10-201209-152 5062133023
L034,L035,L036

-51-
Item pc’s Circuit No. Part Spec. Part No Type
L001,L003,L004,L006,L007,
L008,L009,L011,L012,L015,
32 26 L017,L048,L049,L050,L051, MLB-2012-150 5062133008 0805
L052,L054,L056,L063,L071,
L089,L092,L109,L110,L112
L031,L058,L067,L041,L047,
33 6 HU-1H4516-600J 5062120135 1806
L095
L005,L020,L022,L030,L039,
L040,L043,L044,L045,L046,
L055,L059,L062,L064,L065,
L072,L073,L074,L075,L076,
34 38 MLB-201209-00600L-N2 5062133011 0805
L077,L078,L079,L087,L091,
L094,L097,L111,L113,L114,
L115,L116,L117,L118,L119,
L120,L121,L122
LP13,LP14,LP15,LP16,LP17,
35 6 MLB-3216-0030M4-N2 5062128504 Bead Array
LP18

LP01,LP03,LP05,LP07,LP09,
36 6 MLB-3216-0240M4-N3 5062128505 Bead Array
LP11
37 1 P005 DF14-20P-1.25H (HRS) 5056310015
38 1 Q009 2SK2731 (ROHM) 6626002752
3904 (ZOWIE) 6622002257
Q004,Q005,Q006,Q007,Q008, (FAIRCHILD) 6621038451
39 7 SOT-23
Q020,Q003 (DII) 6622002259
(KEC) 6621015356
R005,R007,R015,R019,R037,
R040,R053,R057,R058,R069,
L070,R072,R073,R074,R094,
R095,R107,R108,R111,R188,
R195,R240,R130,R131,R136,
40 51 R152,R166,R169,R170,R177, 0 5134300009 0603
R183,R186,R191,R197,R198,
R199,R200,R201,R203,R230,
R231,R232,R238,R241,R300,
R364,R365,R245,R246,R247,
R250,R251
41 4 R145,R248,R249,R348 1K 5134310209 0603

42 4 R105,R106,R124,R126 33 5134333009 0603

R011,R012,,R020,R025,R031,
43 11 R032,R033,R045,R046,R225, 75 5134375009 0603
R226
44 2 R139,R224 47K 5134347309 0603
R023,R027,R062,R066,R067,
R085,R086,R092,R093,R104,
45 25 R115,R117,R132,R137,R172, 10K 5134310309 0603
R173,R176,R229,R263,R050,
R234,R227,R228,R243,R244, ,

-52-
Item pc’s Circuit No. Part Spec. Part No Type

45 1 R063 24K 5134324309 0603

46 2 R041,R060 5.1K 5134351209 0603

R014,R055,R059,R179,R180,
47 9 10 5134310009 0603
R181,R182,R184,R189

48 4 R022,R118,R153,R154,R233 2.2K 5134322209 0603

49 3 R003,R036,R061 2.7K 5134327209 0603

50 2 R001,R002 300 5134330109 0603

21 1 R140 240 5134324109 0603

52 1 R112 390 5134339109 0603

53 2 R028,R029 47 5134347009 0603

R088,R089,R113,R114,R142,
54 8 2.4k 5134324209 0603
R143,R193,R196

55 2 R147,R148 2.2 5134322909 0603

56 2 R103,R110 270 5134327109 0603

R021,R024,R096,R116,R123,
57 8 4.7K 5134347209 0603
R119,R146,R235

58 1 R237 3.3K 5134333209 0603

R008,R009,R010,R042,R043,
59 11 R044,R064,R065,R081,R360, 100 5134310109 0603
R362
R077,R078,R079,R149,R161,
60 14 R163,R165,R204,R205,R206, 18 5134318009 0603
R207,R208,R209,R220
R080,R087,R097,R098,R159,
61 14 R162,R164,R210,R211,R212, 56 5134356009 0603
R213,R214,R215,R218
62 1 R216 51 5134351009 0603
63 1 R190 1M 5134310509 0603

-53-
 Main Board SMD IC
Item pc’s Circuit No. Part Spec. Part No AVL
1 2 I005,I025 74F14 6646021451 FAIRCHILD
2 2 I034,I010 P15V33690Q 6644036001 PERICOM

RC1117ST 33 6640003858 FAIRCHILD

3 5 I002,I003,I007,
AP1117E-3.3 6640010150 ATC
I008,I017
6640003867 FAIRCHILD
4 1 I015 RC1117ST 25
6640010159 ATC
5 1 I006 AD9883A-110 6649001852
ADI
6 1 I001 AD9883A-140 6649001853
7 1 I004 24C02 6647051862 CATALYST
8 1 I044 MSP 3410G 6644077051 MICRONAS
AT24C16 6647026301 ATMEL
9 2 I009,I013 24LC16B 6647026355 MICROCHIP
AM24LC16S8 6647051653 ATC
10 1 I016 LD1084 6640005156 EGTEK
11 1 I018 SAA7118E 6647052050 PHILIPS
12 1 I019 TP6760 6646000351 TOPRO
13 1 I020 HY57V161610 6646013651 HYNIX
14 1 I012A 44P Socket 5056304402 Cen-Link
15 1 I027 SI9933DY 6644075755 VISHAY Silicon
16 1 I014 THC63LVDM83A 6644001354 THINE
17 1 I030 PI5C3253 6645008657 EPCO

-54-
12.2 Tuner Board ( PWB-0564)

Item pc’s Circuit No. Part Spec. Part No AVL

1 1 U0564 PWB-0564 5053105640 TKE
RT02,RT07,RT21,
2 4 0 5134300009
CT07 YAGEO,RAYAL
3 1 RT03 1K 5134310209
4 2 CT02,CT05 0.1uF 5230005491 PHYCOMP,TAIYO
YUDEN,
5 1 CT06 47P 5240647091 TDK,WALSIN
6 1 CT01 100uF/16V 5218007991 NIPPON
7 1 CT03 10U/16V 5218007891 CHEMICON
8 1 CT08 47U/16V 5218008991 PANASONIC
9 2 LT01, LT02 Coil Peaking 100uH 5064410129 TDK
10 1 UT01 Tuner FQ1216ME/IH-3 5000100054 PHILIPS

12.3 I/O Board ( PWB-0638 )

Item pc’s Circuit No. Part Spec. Part No AVL

1 1 U0638 PWB-0638 5053106380 TKE
2 1 PI01 Euro Scart 5556314100 Jya-Tai
3 1 PI02 RCA JACK(GREEN) 5056302057 S.C
4 1 PI03 RCA JACK(BLUE) 5056302058 S.C
5 1 PI04 RCA JACK(RED) 5056302039 S.C

6 1 PI08 RCA JACK(YELLOW) 5056302055 S.C

7 1 PI10 S-VIDEO 5056302049 S.C

8 23 C801 ~ C823 10p/50V 5240610091 Yuden , Walsin
9 17 L801 ~ L817 Bead Chip MLB-1608 5062132307 Maglaye

12.4 LED & IR Board ( PWB-0565 )

Item pc’s Circuit No. Part Spec. Part No AVL
1 1 C601 10U/16V 5214020800 CHINSAN
2 1 D601 Dual LED L-5T8YG 6618018167
PARA LIGHT
3 1 IR01 SENSOR PL-IRM0101 6646036600
4 1 P601 6PIN CONN. 5056415685 JOWLE
5 1 R601 1K 5142110295 SANYO

-55-
12.5 Key Board ( PWB-0565 )

Item pc’s Circuit No. Part Spec. Part No AVL

4 1 U0565 KEY/LED BOARD 5053105650 TKE
1 3 J611,J612,J613 WIRE 6119210605 TATUNG
2 1 P602 S10B-PH-K , Base&Pin 5056416038 JST,JWT
S601,S602,S603,
3 8 S604,S605,S606, Tact Switch 5054512951 FORWARD
S607,S608

12.6 Power Module / Panel / Inverter /Accessories

Item pc’s Circuit No. Part Spec. Part No AVL

Power Module: PWB-0656
1 1 PB01 5000100077 HJC
150W, 5V/3A, 24V/6A
27” Panel : V270W1-L01 5051253641 CMO
2 1 V901
30” Panel : V296W1-L03 5051253642 CMO
27” Inverter: PLCD17271401
5000100074 E-Max
(24V/850mA/58KHz)
3 1 U901
30” Inverter : PLCD17301
5000100069 E-Max
(24V/3.75A/72mA)
4 1 P021A WIRE 10P (to Key) 5057410111
5 1 P015A WIRE 6P (to Sensor) 5057406116
6 1 PJ11A WIRE 4P (to Speaker) 5057404365
7 1 P003A WIRE10P (to AudioAmp) 5057410025 Liang-san
8 1 P802A WIRE 12P/8P (Power-Invert.) 5057412020
9 1 P005A WIRE 20P (to Panel ) 5057430018
10 1 P030A WIRE 2P (TV-Power-Main) 5057402289
11 1 SP01 Speaker :SPK 4-OHM 10W 5055123700 SEA TRADE

12 1 SP02 Speaker :SPK 4-OHM 10W 5055123700 SEA TRADE

13 1 RT01 Remote Control RM-L1703 5000100094 FORWARD
14 1 P101 SIGNAL CABLE 15P D-Sub 5057415248 Liang-san
15 1 P801 (option) SP-28/IS-14 Black 5056706150 I-Sheng
27” USER'S MANUAL I 5030057017 TATUNG
16 1 Y001 27” USER'S MANUAL II 5030057030 TATUNG
30” USER'S MANUAL I 5030057013 TATUNG
30” USER'S MANUAL II 5030057029 TATUNG

-56-
 13. Mechanical Disassembly
13.1 Exploded Drawing of 27 ” :

-57-
13.2 Exploded Drawing of 30” :

-58-
 14. Mechanical Parts List
14.1 Parts List of 27” :
CKT NO. DESCRIPTION PARTS NO.
M1 FRONT COVER 5642292101
M2 SP-SCREEN 5642317800
M3 NON-WOVEN FABRICS 5642028106
M4 METAL-MESH-SPEAKER 5642514000
M5 IR LENS 5040331300
M6 INSULATION-INVERTER 5646503600
M7 LCD MBRACKET 5642725600
M8 TUNNER PCB CLAMP 5642678700
M9 BRASS SPACER 5642847107
M10 WIRE MOUNTS 5642679000
M11 POWER PCB SHIELD 5646256100
M12 POWER PCB COVER 5646256200
M13 TUNNER COVER 5642318204
M14 CHASSIS PCB SHUELD 5646252900
M15 SIGNAL COVER 5642318104
M16 VISA BRACKET 5648731700
M17 AV PCB BRACKET 5648739400
M18 CONTROL KEY 5642847102
M19 BACK COVER 5642292201
M20 EVA SPONGE 5642026208
M21 AV PCB SHIELD 5646252401
M22 AV COVER 5642420202
M23 NECK FRONT COVER 5641412503
M24 HINGE 5648740501
M25 NECK BACK COVER 5641412603
M26 BASE 5642412703
M27 BASE BRACKET 5640407200
M28 BASE WHEEL 5648602000
M29 RIVET 5640205102
S1 SPEAKER SCREW 5640228400
S2 PZP M3X8 7134161182
S3 PZP M4X12 7134251682
S4 PP M4X10 7001261412
S5 PP M2X5 7001070514
S6 PPW M3X6 7000311032
S7 PPW M3X10 7000311042
S8 AV COVER SCREW 5640228300
S9 PPW M4X12 7000311132
S10 PF M4X8 7004261112
S11 BFB M4X12 7034251652
S12 PP M4X6 7001260612

-59-
14.2 Parts List of 30” :

CKT NO. DESCRIPTION PARTS NO.

M1 Front Cover 5642291902
M2 Back Cover 5642292002
M3 Neck Front Cover 5641412503
M4 Neck Back Cover 5641412603
M5 Base 5641412703
M6 AV Cover Hole 5642420202
M7 AV Cover 5642318004
M8 Signal Cover 5642318104
M9 Tuner Cover 5642318204
M10 IR Lens 5640331300
M11 Tuner PCB Clamp 5642678700
M12 Control Key 5642847102
M13 LCD Bracket 5642725500
M14 Hinge 5648740500
M15 Base Bracket 5640407200
M16 Chassis PCB Shield 5646252900
M17 AV PCB Shield 5646253100
M18 Power PCB Shield 5646256100
M19 Power PCB Cover 5646256200
M20 Visa Bracket 5648731700
M21 AV PCB Bracket 5648739400
M22 INVTER Insulation 5646504900
M23 Brass Spacer 5640228500
M24 EVA Sponge 5642026207
M25 Sensor Holder 5642678900
M26 Base Wheel 5648602000
M27 Plastic Rivet 5640205102
M28 Wire Mounts 5642679000
M29 Heat Sink 5646405209
M30 SPK Screen Bracket 5642317400
M31 Non-Woven 5642028100
M32 SPK Screen 5642513900

-60-
CKT NO. DESCRIPTION PARTS NO.
S1 AV Cover Screw 5640228300
S2 Speaker Screw 5640228400
S3 PP M2x5 S-Ni 7001070514
S4 PZP M4X12 S-ZN 7134251682
S5 PF M4X8 S-ZN 7004261112
S6 BFB M4X12 S-ZN 7034251652
S7 PPW M4X12 7000311132
S8 PP M4X6 S-ZN 7001260612
S9 PZP M3X8 S-ZN 7134161180
S10 PPW M3X6 S-ZN 7000311032
S11 PPW M3X10 S-ZN 7000311042

-61-