A350 Technical Training Manual T1+T2 Mechanical and Avionics A350 RR TRENT XWB Airframe (Level1)

A350
TECHNICAL TRAINING MANUAL

T1+T2 Mechanical and Avionics A350 RR TRENT
XWB
AIRFRAME (LEVEL1)
This document must be used for training purposes only.
Under no circumstances should this document be used as a reference.
It will not be updated.
All rights reserved

No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,
without the prior written permission of AIRBUS S.A.S.
AIRBUS Environmental Recommendation.

Please consider your environmental responsability before printing this document.
TP REV 2.1
T1+T2 Mechanical and Avionics A350 RR TRENT XWB
A350 AIRFRAME (LEVEL1)
TECHNICAL TRAINING MANUAL 03/05/2018
Hydraulic Power System Presentation.....................................2

Landing Gear System Presentation.......................................18
Structure System Presentation..............................................74
Doors Presentation................................................................94
Equipments and Furnishings Presentation..........................120
Cabin Presentation...............................................................140
Cargo compartment Presentation........................................142
Flight Controls System Presentation....................................152
Oxygen System Presentation...............................................186
Water/Waste System Presentation......................................200
TABLE OF CONTENTS Page 1

© AIRBUS SAS 2018 All rights reserved. Confidential and proprietary document.
TP REV 2
HYDRAULIC POWER SYSTEM PRESENTATION

Overview
The function of the hydraulic power system is to supply hydraulic power
to the aircraft hydraulic consumers.
General familiarization training for this system focuses on:
- Main hydraulic power
- Auxiliary hydraulic power
- Hydraulic system monitoring.
VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 2

TP REV 2
OVERVIEW

TP REV 2

- The nose wheel steering
Main Hydraulic Power - Presentation - The flight controls.
The function of the reservoir pressurizing system is to keep the
Function Description
hydraulic reservoirs pressurized to supply a positive flow of hydraulic
The main hydraulic-power system includes: fluid to the pumps. The reservoirs of the Green and Yellow
- The Green main hydraulic-power system hydraulic-power systems are self-pressurized which prevents the
- The Yellow main hydraulic-power system cavitation of the hydraulic pumps.
- The reservoir pressurizing system. Each system has an accumulator and a pressure maintaining unit. The
The function of the main hydraulic-power system is to supply accumulator absorbs the delivery pulsations and pressure surges of
hydraulic power to the aircraft hydraulic consumers. The Green and the pumps. With the pressure maintaining unit, the accumulator keeps
Yellow main hydraulic-power systems are fully independent of each the reservoir pressurized after a system shutdown.
other and with no hydraulic fluid transfer between them. The
bootstrap-type Green and Yellow hydraulic reservoirs supply hydraulic
fluid to engine pumps. Two engine pumps for each system pressurize
the hydraulic fluid to 5000psi . Each hydraulic power system has one
engine pump on each engine.
Each engine pump has a clutch to mechanically disconnect the pump
drive shaft from the engine Accessory Gearbox (AGB). Each engine
pump case-drain line has one fuel hydraulic heat-exchanger. The fuel
is the cooling agent that decreases the temperature of the hydraulic
fluid when it is necessary. Each engine pump suction line has a Fire
ShutOff Valve (FSOV) which is installed downstream of the reservoir.
The function of the FSOV is to stop the hydraulic fluid supply to the
engine pump.
The Green main hydraulic-power system supplies hydraulic power
to:
- The brakes and their accumulator
- The Ram Air Turbine (RAT) retraction actuator
- The Main Landing Gear (MLG) extension/retraction
- The flight controls.
The Yellow main hydraulic-power system supplies hydraulic power
to:
- The Nose Landing Gear (NLG) extension/retraction

TP REV 2
MAIN HYDRAULIC POWER - PRESENTATION - FUNCTION DESCRIPTION

TP REV 2

Main Hydraulic Power - Presentation (continued)
Location
There are two engine pumps on each engine, one for the Green
hydraulic-power system and one for the Yellow hydraulic-power
system. The engine pumps are installed on the Accessory Gearbox
(AGB) on each engine. The Green reservoir is installed on the right
side of the rear belly fairing. The Yellow reservoir is installed on the
keel beam of the MLG bay. The fuel hydraulic heat-exchangers are
installed in the wings (fuel tanks).

TP REV 2
MAIN HYDRAULIC POWER - PRESENTATION - LOCATION

TP REV 2

Auxiliary Hydraulic Power - Presentation - The NLG extension/retraction
- The nose wheel steering
The auxiliary hydraulic-power system includes: A hydraulic auxiliary pump in the Yellow auxiliary hydraulic-power
- The Green auxiliary hydraulic-power system system supplies hydraulic power to the brake accumulators and cargo
- The Yellow auxiliary hydraulic-power system. doors for ground operations and maintenance.
The function of the Green and Yellow auxiliary hydraulic-power
systems is to supply hydraulic power to the hydraulic consumers for
ground operation and maintenance when no engine is in operation.
Each hydraulic-power system has one electric pump which can
pressurize the hydraulic fluid to 5000psi . The electric pumps are used
on the ground only. It is also possible to pressurize the hydraulic fluid
through a hydraulic ground-power cart connection. The Green and
Yellow auxiliary hydraulic-power systems are fully independent of
each other and with no hydraulic fluid transfer between them.
The isolation valves (when closed) in the Green and Yellow auxiliary
hydraulic-power systems let the hydraulic power to:
- Operate the brakes on the ground
- Pressurize the brake accumulators
- Operate the cargo doors of the Yellow auxiliary hydraulic-power
system.
If necessary, for maintenance procedures, it is possible to send
hydraulic power to all hydraulic consumers of the Green and Yellow
auxiliary hydraulic-power systems with isolation valve open.
The Green auxiliary hydraulic-power system supplies hydraulic power
to:
- The RAT retraction actuator
- The MLG extension/retraction
The Yellow auxiliary hydraulic-power system supplies hydraulic
power to:
- The cargo doors

TP REV 2
AUXILIARY HYDRAULIC POWER - PRESENTATION - FUNCTION DESCRIPTION

TP REV 2

Auxiliary Hydraulic Power - Presentation (continued)
Location
There are two electric pumps. The electric pump of the Green
hydraulic-power system is installed on the aft keel beam, in the MLG
bay. The electric pump of the Yellow hydraulic-power system is
installed on the forward keel beam, in the MLG bay. The ground
hydraulic-power cart connections are on the Green and Yellow Ground
Service Panels (GSPs). The hydraulic auxiliary pump is installed on
the Yellow GSP. The Green GSP is installed in the belly fairing, aft
of the MLG bay. The Yellow GSP is installed in the belly fairing, in
front of the MLG bay.

TP REV 2
AUXILIARY HYDRAULIC POWER - PRESENTATION - LOCATION

TP REV 2

Hydraulic System Monitoring - Presentation
There are two Hydraulic Monitoring and Control Applications
(HMCAs), HMCA-G and HMCA-Y. Each one monitors and controls
one of the two hydraulic-power systems, Green or Yellow. The
function is hosted in Core Processing Input/Output Module (CPIOM).
Each HMCA does the control and monitoring function on its related
hydraulic power system. Each HMCA collects quantity, pressure and
temperature data of the hydraulic-power systems. It has interfaces
through the Avionics Full Duplex Switched Ethernet (AFDX) to other
aircraft systems to which it transmits this data.
The HMCA controls the pumps and valves. It receives the commands
through the AFDX.
Interface
The CPIOM sends the collected hydraulic-power systems data to the
CDS HYD page through the AFDX.

TP REV 2
HYDRAULIC SYSTEM MONITORING - PRESENTATION - FUNCTION DESCRIPTION & INTERFACE

TP REV 2

Control and Indicating - Presentation
Controls and indications are on the cockpit overhead panel, on:
- The "GND HYD" panel for the control of the electric pumps
- The "HYD" panel for the control of the engine pumps.
Indications are on the cockpit instrument panel, on the ECAM SD "HYD"
page.
Controls and indications are also for the maintenance tasks, on:
- The Green GSP, aft of the MLG bay
- The Yellow GSP, forward of the MLG bay.

TP REV 2
CONTROL AND INDICATING - PRESENTATION

TP REV 2

Maintenance
Tools
An approved 5000psi hydraulic ground-power cart is used to operate
the hydraulic-power systems and its hydraulic consumers for
maintenance tasks.
Maintenance Practices
An approved repair method is necessary to do repairs on 5000psi pipes
of the hydraulic-power systems. The methods are in AirN@v/Line
maintenance procedure.
The hydraulic fluid for the Green and Yellow hydraulic-power systems
is a low density phosphate-ester hydraulic fluid. Thus it is mandatory
that no high-density hydraulic fluid is used in the system. High-density
hydraulic fluid can cause damage to the hydraulic-power systems.

TP REV 2
MAINTENANCE - TOOLS & MAINTENANCE PRACTICES

TP REV 2
LANDING GEAR SYSTEM PRESENTATION

Overview
The function of the Landing Gear (L/G) system is to support the aircraft
on the ground and transmit taxi, takeoff, landing and braking loads to the
structure.
It extends and retracts the L/G.
It decreases the aircraft speed with the braking system and steers the
aircraft on the ground.
It also monitors some braking subsystems.
General familiarization training for this system focuses on the:
- Main Landing Gear (MLG) and Doors
- Nose Landing Gear (NLG) and Doors
- Extension and Retraction
- Wheels and Brakes
- Landing Gear Monitoring System (LGMS)
- Nose Wheel Steering and Control.
VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 18

TP REV 2
OVERVIEW

TP REV 2

There are three doors for each MLG, the main door, the fixed fairing
Main Gear and Doors - Presentation door and the hinged door.
The main door is operated hydraulically by a door actuator.
Function/Description
The fixed fairing door and the hinged door are mechanically attached
A MLG is installed in each wing. They support the aircraft on the to the leg.
ground and transmit taxi, takeoff, landing and braking loads to the
wing. In flight, each MLG retracts inboard into its L/G bay in the
fuselage.
The doors cover the L/G bays when the L/Gs are retracted. This gives
the aircraft its aerodynamic profile.
A350-900
Each MLG has these parts:
- An Oleo-pneumatic Shock-absorber (Leg) that includes a four-wheel
bogie-beam assembly
- Forward and Aft Side Stays and Lock Stays
- Two pairs of Downlock Springs
- A Hydraulic Pitch Trimmer
- A Retraction Actuator
- Two Lock Stay Actuators.
There are three doors for each MLG, the main door, the fixed fairing
door and the hinged door.
The main door is operated hydraulically by a door actuator.
The fixed fairing door and the hinged door are mechanically attached
to the leg.
A350-1000
Each MLG has these parts:
- An Oleo-pneumatic Shock-absorber (Leg) that includes a six-wheel
bogie-beam assembly
- Forward and Aft Side Stays and Lock Stays
- Two pairs of Downlock Springs
- An Independent Pitch Trim Actuator
- Two Lock Stay Actuators.

TP REV 2
MAIN GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
MAIN GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
THIS PAGE INTENTIONALLY LEFT BLANK

TP REV 2

Nose Gear and Doors - Presentation
The NLG is installed in the forward fuselage. It supports the forward
part of the A/C on the ground and transmits taxi, takeoff and landing
loads to the airframe. In flight, the NLG retracts forward into its L/G
bay in the fuselage.
The doors cover the L/G bay when the L/G is retracted. This gives
the aircraft its aerodynamic profile.
The NLG has these parts:
- An Oleo-pneumatic Shock-absorber (Leg) that includes a twin wheel
axle
- A Drag Stay and a Lock Stay
- A Lock Stay Actuator
- Two Steering Actuators
- Two Downlock Springs.
There are four doors for the NLG, two forward doors and two rear
doors.
The two forward doors are operated hydraulically by two door
actuators (one actuator per door).
The two rear doors are mechanically attached to the leg.

TP REV 2
NOSE GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

Extension and Retraction - Presentation
The Landing Gear Extension and Retraction System (LGERS) controls
and monitors the extension and retraction of the L/G.
The system is divided into three subsystems, the:
- Normal extension and retraction system
- Emergency (alternate) extension system
- Ground Door Opening (GDO) system.

TP REV 2
EXTENSION AND RETRACTION - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

Normal Extension and Retraction - Presentation Interface
Two independent hydraulic power supplies are used to operate the
Function/Description L/G in normal operation.
The normal extension and retraction system extends and retracts the The green hydraulic system supplies the hydraulic power to operate
L/G and opens/closes the L/G doors in normal operation. the MLG and the MLG doors.
It uses Core Processing Input/Output Modules (CPIOM) (LGERS The yellow hydraulic system supplies the hydraulic power to operate
application) to control the operational sequence of the L/G and to the NLG and the NLG doors.
monitor the L/G positions.
The system is electrically controlled and hydraulically operated by:
- Gear and door selector valves
- Gear and door uplock control-valves
- Gear and door actuators
- Gear and door uplocks.
The L/G lever in the cockpit is used to extend or retract the L/G. The
L/G lever signals are sent to the CPIOMs (LGERS application) via
the Avionics Full Duplex Switched Ethernet (AFDX) network.
The normal extension and retraction system monitors the position of
the gears and doors. The position data is sent to the CPIOMs via the
AFDX network for system monitoring and the Control and Display
System (CDS).
The normal extension and retraction system controls and monitors
the isolation, selector and uplock valves, the actuators and the uplocks.
Data is sent to the CPIOMs via the AFDX network.
Hydraulic power is supplied through the isolation valve to the gear
and door selector valves and the gear and door uplock valves. The
hydraulic power then goes from the:
- Gear selector valves to the gear actuators
- Door selector valves to the door actuators
- Gear uplock control-valves to the gear uplocks
- Door uplock control-valves to the door uplocks.

TP REV 2
NORMAL EXTENSION AND RETRACTION - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2
NORMAL EXTENSION AND RETRACTION - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

TP REV 2

Alternate Extension - Presentation
The alternate extension system is used when the normal extension
system is not available because of failure.
The system releases the L/G and doors from their uplocks, the doors
open and the L/G extends under gravity (Free Fall).
"L/G GRVTY EXTN" switches in the cockpit control the operation
of the alternate extension system.
The system is an electrically controlled hydro-mechanical system. It
uses two Alternate Power Packs, one for the MLG and one for the
NLG.
When the "L/G GRVTY EXTN" switches are set to the down position:
- Signals go to the Alternate Extension Control Modules (AECM)
- The isolation valves are de-energized.
Hydraulic power is supplied:
1 To the vent valve which connects all actuators to return.
2 To the door-uplock actuators, to release the uplock, to open the
doors under gravity.
3 To the gear-uplock actuators, to release the uplock, to extend the
gear under gravity.

TP REV 2
ALTERNATE EXTENSION - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
ALTERNATE EXTENSION - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

Ground Door Opening System - Presentation (A350-900 ONLY)
The Ground Door Opening (GDO) system is used to open the L/G
doors to give access to the L/G bays for maintenance.
Mechanical control via handles, cables and linkages is used to open
the L/G doors. Hydraulic power is used to close the L/G doors.
The GDO handles are installed on panels adjacent to each L/G bay.
When the GDO handle is moved to the OPEN position the system
releases the doors from their uplocks and the doors open under gravity.
A bypass valve is also actuated by the GDO handle. It isolates the
door actuator from the hydraulic supply.
The doors close when the GDO handle is moved to the CLOSE
position and its hydraulic system is pressurized.

TP REV 2
GROUND DOOR OPENING SYSTEM - PRESENTATION (A350-900 ONLY) - FUNCTION/DESCRIPTION

TP REV 2

Ground Door Opening System - Presentation (A350-1000
ONLY)
The Ground Door Opening (GDO) system is used to open the L/G
doors to give access to the L/G bays for maintenance.
Electrical control and power supply from Ground Door Opening Panels
(GDOP) to the Bypass valves and Uplocks is used to open the L/G
doors. Hydraulic power is used to close the L/G doors.
The GDOP are installed on panels adjacent to each L/G bay. When
the GDOP rotary handle is moved to the OPEN position the system
releases the associated door(s) from their uplock(s) and the door(s)
open under gravity.
A bypass valve is also actuated by the GDOP rotary handle. It isolates
the door actuator from the hydraulic supply.
The doors close when the GDOP rotary handle is moved to the CLOSE
position and its hydraulic system is pressurized.

TP REV 2
GROUND DOOR OPENING SYSTEM - PRESENTATION (A350-1000 ONLY) - FUNCTION/DESCRIPTION

TP REV 2

Extension and Retraction - Presentation
Control and Indicating
A L/G control lever located on the main instrument panel in the cockpit
is used to extend or retract the L/G.
Alternate extension switches located on the center pedestal in the
cockpit can be used to extend the L/G with the alternate extension
system.
Indication of the L/G position is shown on the "WHEEL" page of the
System Display (SD) on the CDS in the cockpit.
Independent downlock indication is shown on the Primary Flight
Displays (PFD) in the cockpit.

TP REV 2
EXTENSION AND RETRACTION - PRESENTATION - CONTROL AND INDICATING

TP REV 2

Wheels and Brakes - Presentation
The wheels and brakes system lets the crew control the speed of the
aircraft on the ground. The system is divided into four subsystems:
- Normal braking
- Alternate braking
- Emergency braking
- Parking braking.
The normal, alternate and emergency braking systems decrease the
aircraft speed on the ground.
The parking braking system prevents movement of the aircraft when
it is parked.
Each brake is a single cavity brake.
A350-900
The Yellow main hydraulic power system supplies the hydraulic power
for the brake units at wheels 1 to 4. The Green main hydraulic power
system supplies the hydraulic power for the brake units at wheels 5
to 8.
A350-1000
The Yellow main hydraulic power system supplies the hydraulic power
for the brake units at wheels 1 to 4, 6 and 8. The Green main hydraulic
power system supplies the hydraulic power for the brake units at
wheels 5, 7 and 9 to 12.

TP REV 2
WHEELS AND BRAKES - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

The aircraft speed data is sent by the Air Data and Inertial Reference
Normal Braking - Presentation System (ADIRS) to the RBCUs and BCS applications. This data is
used by the anti-skid function to prevent the tires from skidding.
The normal braking system decreases the aircraft speed on the ground
(landing, taxi and in case of a rejected take off). It also stops the
rotation of the MLG wheels before the L/G is retracted (MLG
retraction braking).
The system is fully "Brake by Wire" and controlled by signals from:
- The Captain's or the First Officer's (F/O) brake pedals
- The brake control panel
- The L/G control lever.
Control and monitoring of the normal braking system is done by the
CPIOMs (Braking Control System (BCS) application) via two Remote
Braking Control Units (RBCU).
Protection against tire skidding is given by the anti-skid function.
The hydraulic power for the normal braking system is supplied by the
aircraft hydraulic power supply. A Pressure Limiting Valve (PLV)
reduces the hydraulic pressure from 5000psi to 3000psi.
Control signals from the pedals, the brake control panel and the L/G
control lever are sent to the CPIOMs (BCS application). Signals
between the CPIOMs (BCS application) and the normal braking system
are sent via two Remote Braking Control Units (RBCU).
Hydraulic power is supplied through the (ON/OFF) normal selector
valve to the (regulating) servo valve, then to the brake units via the
shuttle valve.
Tachometers installed in the axle of each wheel measure the wheel's
speed for anti-skid protection.
Interface
Two independent hydraulic power supplies are used to operate the
brake units.

TP REV 2
NORMAL BRAKING - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2
NORMAL BRAKING - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

TP REV 2

Normal Braking - Presentation (continued)
Location
The two RBCUs are installed in the avionics bay.

TP REV 2
NORMAL BRAKING - PRESENTATION - LOCATION

TP REV 2

In alternate braking, there is only one servo valve in operation for
Alternate Braking - Presentation each pair of wheels on the same axle.
Function/Description Interface
The alternate braking system decreases the aircraft speed on the ground The yellow hydraulic system refills the accumulator through an
(landing, taxi and in case of a rejected take off). It operates when the Alternate Refill Valve (ARV). The accumulator supplies the hydraulic
normal braking system is not available. power to operate the brake units:
The system is fully "Brake by Wire" and controlled by signals from A350-900
the: At wheels 1 to 4.
- Captain's or the First Officer's (F/O) brake pedals A350-1000
- Brake control panel. At wheels 1 to 4, 6 and 8.
Control and monitoring of the alternate braking system is done by the The green hydraulic system refills the accumulator through an ARV.
CPIOMs (BCS application), via two Remote Braking Control Units The accumulator supplies the hydraulic power to operate the brake
(RBCU). units:
Protection against tire skidding is given by the anti-skid function. A350-900
The hydraulic power for the alternate braking system is supplied by At wheels 5 to 8.
two accumulators. A350-1000
A350-900 At wheels 5, 7 and 9 to 12.
One accumulator supplies the hydraulic power for the brake units at The aircraft speed data is sent by the ADIRS to the RBCUs and BCS
wheels 1 to 4. The other accumulator supplies the hydraulic power applications. This data is used by the anti-skid function to prevent the
for the brake units at wheels 5 to 8. aircraft from skidding.
A350-1000
One accumulator supplies the hydraulic power for the brake units at
wheels 1 to 4, 6 and 8. The other accumulator supplies the hydraulic
power for the brake units at wheels 5, 7 and 9 to 12.
Control signals from the pedals and the brake control panel are sent
to the CPIOMs (BCS application). Signals between the CPIOMs (BCS
application) and the alternate braking system are sent via the two
RBCUs.
Tachometers installed in the axle of each wheel measure the wheel's
speed.
Hydraulic power from the accumulators is supplied through the
(ON/OFF) alternate selector valve to the (regulating) alternate servo
valve, then to the brake units via the shuttle valve.

TP REV 2
ALTERNATE BRAKING - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2
ALTERNATE BRAKING - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

TP REV 2

Emergency Braking - Presentation
The emergency braking system decreases the aircraft speed on the
ground (landing, taxi and in case of a rejected take off). It operates
when the normal braking and the alternate braking systems are not
available.
The system is fully "Brake by Wire" and controlled by signals from
the Captain's or the First Officer's (F/O) brake pedals.
Control and monitoring of the emergency braking system is done by
the RBCUs.
When the emergency braking system is active, there is limited braking
pressure and no anti-skid protection.
The hydraulic power for the emergency braking system is supplied
by two accumulators.
A350-900
wheels 1 to 4. The other accumulator supplies the hydraulic power
for the brake units at wheels 5 to 8.
A350-1000
Control signals from the pedals are sent to the RBCUs. Signals are
sent between the RBCUs and the emergency braking system.
Hydraulic power from the accumulators is supplied through the
alternate selector valve to the alternate servo valve, then to the brake
units via the shuttle valve.

TP REV 2
EMERGENCY BRAKING - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
EMERGENCY BRAKING - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

Parking Braking - Presentation
The parking braking system prevents the movement of the aircraft
when it is stopped on the ground. It can also be used to decrease the
aircraft speed on the ground (landing, taxi and in case of a rejected
take off) as the ultimate braking function.
The system is controlled by the parking brake handle in the cockpit.
When the parking braking system is active, there is full braking
pressure (3000psi) and no anti-skid protection.
The hydraulic power for the parking braking system is supplied by
two accumulators.
A350-900
wheels 1 to 4. The other accumulator supplies the hydraulic power
for the brake units at wheels 5 to 8.
A350-1000
Signals from the parking brake handle control the (ON/OFF) parking
brake selector valve.
Hydraulic power from the accumulators is supplied through the parking
brake selector valve to the alternate servo valve, then to the brake
units via the shuttle valve.
The parking braking system is monitored by the CPIOMs (BCS
application) via the RBCUs.

TP REV 2
PARKING BRAKING - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
PARKING BRAKING - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

Wheels and Brakes - Presentation
The main controls and indicating for the wheels and brakes systems
are in the cockpit.
Brake pedals are installed at each pilot's position.
The brake control panel is located on the main instrument panel. The
indications for the systems are displayed on the "WHEEL" page of
the SD on the CDS.
The parking brake control panel is installed on the center pedestal.
The panel includes the park brake handle and pressure indicators.
A steering disconnect panel is installed on the NLG. A "PARK
BRAKE ON" light (on the steering disconnect panel) is illuminated
when the parking braking system is in operation.

TP REV 2
WHEELS AND BRAKES - PRESENTATION - CONTROL AND INDICATING

TP REV 2

TP REV 2

TP REV 2

Landing Gear Management System - Presentation
The Landing Gear Management System:
- Measures the temperature of each brake unit and gives indication of
the temperatures in the cockpit (Brake System Temperature)
- Decreases the temperature of the brake units (Brake Cooling
(optional))
- Measures the pressure of each tire and gives indication of the
pressures in the cockpit (Tire Pressure Indicating System (TPIS)).
Brake System Temperature:
Brake Temperature Sensors (BTS) are installed in each brake unit.
Temperature information from the BTS is sent to the cockpit via the
AFDX network and CPIOMs (LGMS application). The temperature
of each brake unit is displayed on the "WHEEL" page of the SD on
the CDS.
Brake Cooling (optional):
The brake cooling system uses Brake Cooling Fans (BCF) to decrease
the temperature of each brake unit.
The system is controlled by a "BRK FAN" P/BSW in the cockpit. The
control signals are sent to each BCF via the AFDX network and the
CPIOMs (LGMS application).
TPIS:
Pressure sensors are installed on each wheel. Pressure information is
sent to the cockpit via the AFDX network and CPIOMs (LGMS
application). The pressure of each tire is displayed on the "WHEEL"
page of the SD on the CDS.
The BCFs are controlled by a "BRK FAN" P/BSW on the brake control
panel in the cockpit.

TP REV 2
LANDING GEAR MANAGEMENT SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & CONTROL AND INDICATING

TP REV 2
LANDING GEAR MANAGEMENT SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & CONTROL AND INDICATING

TP REV 2

TP REV 2

Nose Wheel Steering Control System - Presentation
The Nose Wheel Steering (NWS) Control System controls and changes
the direction of the aircraft when it moves on the ground with engine
power.
The system is "Steer by Wire" and controlled by signals from the:
- Captain's or the F/Os handwheels
- Captain's or the F/Os rudder pedals
- Autopilot.
Control and monitoring of the NWS system is done by the CPIOMs
(Wheel Steering Control System (WSCS) application).
The NWS system is powered hydraulically.
An alternate steering mode can be used if the normal steering mode
is not available or not serviceable. The alternate steering mode uses
differential braking on the aft MLG wheels to steer the aircraft.
Control signals from the rudder pedals, the handwheels and the
autopilot (in PRIMs) are sent to the CPIOMs (WSCS application).
Signals are sent between the CPIOMs (WSCS application) and the
steering system.
Control signals from the handwheels are sent to the CPIOMs (BCS
application) when the alternate steering (differential braking) mode
is engaged.
The Yellow main hydraulic power is supplied through the (ON/OFF)
steering selector valve to the (regulating) servo valve, then to the
steering actuators.
Interface
The Yellow hydraulic system supplies the hydraulic power to operate
the NWS system.

TP REV 2
NOSE WHEEL STEERING CONTROL SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Nose Wheel Steering Control System - Presentation (continued)
The indications for the NWS system are displayed on the "WHEEL"
page of the SD on the CDS.
The NWS handwheels and the rudder pedals that control the NWS
system are installed at each pilot's position.

TP REV 2
NOSE WHEEL STEERING CONTROL SYSTEM - PRESENTATION - CONTROL AND INDICATING

TP REV 2
STRUCTURE SYSTEM PRESENTATION

Overview
General familiarization training for this chapter focuses on:
- The aircraft structure
- The materials
- The structure layout
- The window layout.
VM51P1LEVEL0101_003 - Structure System Presentation Page 74

TP REV 2
OVERVIEW

TP REV 2

Wings:
Aircraft structure - Presentation The wings include the center wing box and the outer wing boxes with
the movable surfaces, the flaps, the ailerons, the spoilers, the droop
panels and the slats. Each wing has a winglet at the tip of the wing.
The aircraft structure is divided into these chapters: The center wing box is a fuel tank.
- 52 for the doors
- 53 for the fuselage
- 54 for the nacelles and pylons
- 55 for the stabilizers
- 56 for the windows
- 57 for the wings.
Doors:
The aircraft has eight passenger doors, four on the right side and four
on the left side.
Two cargo compartment doors at the lower right side of the fuselage
give access to the main cargo compartments.
The bulk cargo access door is on the left side of the fuselage in the
lower rear area.
The doors include the nose and the Main Landing Gear (MLG) doors.
There is a cockpit escape hatch on the right side upper shell of the
cockpit. The primary function of the cockpit escape facilities is to let
the flight crew evacuate the cockpit, when it is not possible to evacuate
through the cabin.
Pylons and Nacelles:
The pylons include the pylon box and the pylon fairings. The pylon
box is a primary structure and the pylon fairings are the secondary
structure.
The nacelles include the air inlet, the fan cowls, the Thrust Reverser
(T/R) cowls and the exhaust.
Stabilizers:
The stabilizers include:
- The Trimmable Horizontal Stabilizer (THS) with two lateral boxes
and a center joint to make one unit and one elevator on each side.
- The vertical stabilizer with the vertical stabilizer box and a rudder.

TP REV 2
AIRCRAFT STRUCTURE - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

TP REV 2

TP REV 2

TP REV 2

In cabin and cargo areas, the passenger and cargo floor crossbeams,
Materials - Presentation the rails, the roller tracks and the struts are metallic (usually
aluminum).
The exhausts of the nacelles and the nose lips of the external structure
There are two different types of composite material structures: are metallic.
- The sandwich structure The pylon box is made of titanium.
The sandwich structure has a honeycomb core and skins, which are Most of the frames are CFRP, in some lower shell areas frames are
made of layers of fabric or tape. The fabric and tape are made of made of titanium.
carbon, aramid or glass. The radome of the aircraft is made of QFRP and the leading edge of
- The monolithic structure the vertical stabilizer is made of GFRP.
The monolithic structure is made of layers of fabric or tape. The fabric
and tapes are made of carbon, aramid or glass.
These are the most frequently used materials for the aircraft structure:
- Carbon Fiber Reinforced Plastic (CFRP)
- Glass Fiber Reinforced Plastic (GFRP)
- Quartz Fiber Reinforced Plastic (QFRP)
- Aluminum alloy
- Titanium alloy
- Steel.
Location
The composite materials weight is more than half of the total structural
weight (with gears).
CFRP is the primary material used for these components:
- The doors
- The fuselage panels
- The nacelles
- The stabilizers
- The wing skins (the 2 last outboard slats are made of hybrid
CFRP/Metallic and remaining all slats are fully metallic parts).
The primary structural components of the pylons are made of titanium
alloys.
The nose fuselage is made of aluminum alloy, except the lower shell
Nose Landing Gear (NLG) bay which is made of CFRP.

TP REV 2
MATERIALS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2
MATERIALS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

TP REV 2

Fuselage Layout - Presentation
The new fuselage layout is made of:
- Four circular joints
- Four panels for each section made of CFRP
- CFRP stringers bonded to the skin
Most of these stringers are omega shaped.
The frame design includes frames with four sections each. Some
sections are made of CFRP and/or others are made of titanium alloy.
The A350-1000 has 6 additional frames forward of the wings and 5
additional frames aft of the wings.

TP REV 2
FUSELAGE LAYOUT - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

TP REV 2

Window Layout - Presentation
The cockpit has six symmetrically installed fixed windows.
There are:
- Two front windows
- Two forward lateral windows
- Two aft lateral windows.
The cabin windows are installed on the left and right sides of the
fuselage.
Compared with other Airbus aircraft, the cabin windows are larger.
The passenger door windows are installed on each passenger door.

TP REV 2
WINDOW LAYOUT - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

Maintenance
Tools
For composite structure inspection, you must use Non Destructive
Testing (NDT) methods. Usually, ultrasonic for monolithic structure
and tap test for sandwich structure.

TP REV 2
MAINTENANCE - TOOLS

TP REV 2
DOORS SYSTEM PRESENTATION

Overview
The doors give access to different compartments or areas for passengers,
crew or maintenance personnel.
- Passenger/Crew doors
- Emergency exit doors
- Cargo doors
- Cargo Door Actuation System (CDAS)
- Passenger compartments fixed partitions interior doors
- Service and miscellaneous doors
- Doors and Slides Management System (DSMS).
VM52P1LEVEL0101_003 - Doors Presentation Page 94

TP REV 2
OVERVIEW

TP REV 2

Passenger/Crew Doors - Presentation
The passengers and crew can use the doors for access or to go out of
the cabin. There are eight doors installed on the aircraft, four on each
side of the cabin. The doors 1L/1R, 2L/2R, 3L/3R and 4L/4R have a
door-mounted slide/raft system. The doors can have a single-lane
slide/raft (type C door) or a dual-lane slide/raft (type A door). The
doors 1L/1R and 3L/3R can have one of the two types, type A or type
C door. But the doors 2L/2R and 4L/4R can have only type A door.
All the doors are plug-type doors. These plug-type doors have the
door-stop fittings on each side of the door and the door-stop fittings
on each side of the door frame (fuselage). In flight, the fuselage stop
fittings and the door-stop fittings are in touch to let the door transmit
the loads (caused by cabin pressurization) to the fuselage.
All the doors open outboard/forward parallel to the fuselage.
A manual overridable door stay mechanism installed on the doors
holds the doors in the open position. A door damper and
emergency-opening actuator is installed on the doors. During
emergency operation, the door damper and emergency-opening
actuator operates as an actuator and this causes a faster movement of
the door. In normal operation, the door damper and emergency-opening
actuator operates as a damper. This makes sure that the door does not
open too quickly, which can cause damage to the fuselage.

TP REV 2
PASSENGER/CREW DOORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
PASSENGER/CREW DOORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

Passenger/Crew Doors - Presentation (continued)
These controls and indications are installed on the inner side of the
passenger/crew door:
- The residual cabin-pressure warning-light
- The slide armed warning-light
- The slide armed warning buzzer
- The mechanical door-locking indicators
- The inner handle
- The door stay pushbutton
- The slide arming lever with safety pin.
An outer handle is installed on the outer side of the door to control
the operation of the door.
With the inner and outer handles you can lock or unlock, latch or
unlatch and lift or lower the door manually. The slide arming lever
puts the slide/raft in the armed or disarmed condition. The door
indication panel shows the residual cabin pressure and the "slide
armed" status. It also supplies an aural warning to tell maintenance
personnel that it is dangerous to operate the door at this time.

TP REV 2
PASSENGER/CREW DOORS - PRESENTATION - CONTROL AND INDICATING

TP REV 2

Emergency Exit Doors - Presentation
The emergency exit doors include:
- The cockpit escape hatch
- The passenger/crew doors.
In an emergency, the passengers and crew use the emergency exits to
go out of the aircraft quickly.
The manually operated cockpit escape hatch is of a plug type.
Location
The cockpit escape hatch is installed in the cockpit ceiling.
In an emergency, the passengers and crew can use passenger/crew
doors 1L/1R, 2L/2R, 3L/3R and 4L/4R to go out of the cabin.
The cockpit escape hatch has outer and inner handles.
The passenger/crew doors have outer and inner handles.

TP REV 2
EMERGENCY EXIT DOORS - PRESENTATION - FUNCTION/DESCRIPTION ... CONTROL AND INDICATING

TP REV 2

Cargo Doors - Presentation
The cargo doors include:
- The forward cargo-compartment door
- The aft cargo-compartment door
- The bulk cargo-compartment door.
The functions of the cargo doors are to:
- Give access to the cargo compartments
- Keep the aircraft pressurized.
The forward and aft cargo doors are of a hook type. They open
outboard and up. From the outer side you can manually lock/unlock
and latch/unlatch the forward and aft cargo doors and operate them
hydraulically from an cargo-door operation panel.
The bulk cargo door is of a plug type and opens inboard and up. You
can operate the bulk cargo door manually from the inside or the outside
of the aircraft.
Location
The forward and aft cargo doors are installed on the lower right side
of the fuselage.
The bulk cargo door is installed aft on the lower left side of the
fuselage.

TP REV 2
CARGO DOORS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

Cargo Doors - Presentation (continued)
The cargo door controls that are installed on or adjacent to each of
the forward and aft cargo doors are:
- One latching handle, to manually latch/unlatch the cargo door
- One locking handle, to manually lock/unlock the cargo door
- An cargo-door operational panel to operate the cargo door.
These give indications for each forward and aft cargo doors:
- A residual pressure light on each forward and aft cargo doors comes
on when residual cabin pressure is sensed.
- The indicator flag and windows on the outer side of each forward
and aft cargo doors show that the cargo doors are correctly closed,
latched and locked.
With the outer door handle you can manually open/close and
latch/unlatch the bulk cargo door. On the inner side of the bulk cargo
door, a quad fitting let the maintenance crew operate the door.

TP REV 2
CARGO DOORS - PRESENTATION - CONTROL AND INDICATING

TP REV 2

Cargo Door Actuation System - Presentation Control and Indicating
The controls and indications available on the cargo-door operation
Function/Description panel of each forward and aft cargo doors are:
The function of the CDAS is to control the hydraulic operation of - A toggle switch for normal operation
each forward and aft cargo door. The Door and Slide Control System - A manual override switch for auxiliary operation
(DSCS) controls and monitors the CDAS. The Yellow main - A green indicator light which comes on when the cargo door actuator
hydraulic-power system supplies hydraulic power to the CDAS is in "fully extended and locked" status.
through the electric pump or the hydraulic auxiliary pump (with a
powered hand tool).
The cargo-door operation panel adjacent to each forward and aft cargo
door has a toggle switch and a manual override switch to control the
door movement.
There are two operation modes:
In normal operation, a toggle switch on the cargo-door operation panel
controls the operation of the cargo doors. The input from the toggle
switch goes through the Avionics Full Duplex Switched Ethernet
(AFDX) to the DSCS. Then the DSCS electrically operates the
cargo-door control valve to extend or retract the cargo door actuator
of the applicable cargo door.
In auxiliary operation, the manual override switch operates the
cargo-door control valve.
Interface
In normal operation, the CDAS has interfaces with:
- The DSCS, to start the Hydraulic Monitoring and Control Application
(HMCA) function through the AFDX.
- The HMCA, to start the electric pump through the AFDX.
- The Yellow main hydraulic-power system, to supply hydraulic power
from the electric pump to the cargo-door control valve.
In auxiliary operation, the CDAS has interfaces with:
- The Yellow main hydraulic-power system, to supply hydraulic power
from the hydraulic auxiliary pump to the cargo-door control valve.

TP REV 2
CARGO DOOR ACTUATION SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION ... CONTROL AND INDICATING

TP REV 2

Passenger Compartment Fixed Partitions and Interior Doors
- Presentation
The passenger compartment fixed partitions and interior doors include
the cockpit door and its Cockpit Door Locking System (CDLS). The
CDLS isolates the cabin area from the cockpit area and it makes the
cockpit access safe. The cockpit door is electrically controlled and is
thicker and stronger than the other doors.
The CDLS controls and monitors the electrical release strikes to lock
or to open the cockpit door through the control unit and the control
panel. In an emergency, the flight crew can open the cockpit-door
decompression and evacuation panel and then use it to go out of the
cockpit.
Location
The cockpit door is installed on the fixed partition located between
the cockpit and the cabin.
The controls for the cockpit door and CDLS are:
- The door handles installed on the cabin and cockpit side of the
cockpit door
- The keypad installed on the cabin side
- The toggle switch installed on the cockpit door panel on the center
pedestal, to control the cockpit door
- The maintenance switch installed on the overhead panel, to inhibit
the CDLS during maintenance work.
The indications for the cockpit door and CDLS are available on:
- The keypad
- The cockpit door panel on the center pedestal.
A buzzer installed on the overhead panel in the cockpit gives an aural
warning to the flight crew.

TP REV 2
PASSENGER COMPARTMENT FIXED PARTITIONS AND INTERIOR DOORS - PRESENTATION - FUNCTION/DESCRIPTION ... CONTROL
AND INDICATING

TP REV 2

- The air-ground connection doors are installed forward of the Main
Service and Miscellaneous Doors - Presentation Landing Gear (MLG).
- The hydraulic service doors are installed in the lower mid area of
the aircraft.
The service and miscellaneous doors include: - The refuel door is installed in the lower mid area of the aircraft.
- Access doors - The water and waste service doors are installed aft of the aft cargo
- Service doors door.
- Overpressure doors - The overpressure doors are installed in the lower fuselage.
- Ram Air Turbine (RAT) doors. - The RAT doors are located in the lower center area of the fuselage.
The access and service doors give access for maintenance to:
- Systems and equipment
- Avionics compartment
- Cargo loading system
- Trimmable Horizontal Stabilizer (THS)
- Auxiliary Power Unit (APU) compartment.
The access and service doors are manually operated and latched doors.
The overpressure doors prevent overpressure in an area where
pneumatic-system components are installed. The overpressure doors
are blowout panels. After they disengage, it is possible to install them
again.
The function of the RAT doors is to keep the RAT and its components
safe when they are in the retracted position. The RAT doors open
in-flight in an emergency condition.
Location
The service and miscellaneous doors are installed in these locations:
- The avionics access door is installed below the cockpit.
- The cargo loading control panel is installed in the forward area of
each cargo door.
- The THS compartment access-door is installed below the THS.
- The Auxiliary Power Unit (APU) access door is installed at the rear
of the aircraft.
- The ground power-unit door is installed aft of the Nose Landing
Gear (NLG).

TP REV 2
SERVICE AND MISCELLANEOUS DOORS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

The DSCS delivers ALL DOOR status to the CPCS through the
Doors and Slides Management System - Presentation AFDX.
The functions of the DSCS are:
- To give indications related to the status of the doors and slides.
- To control the operation of the CDAS to open or close the forward
and the aft cargo doors.
- To supply the visual residual pressure indication for all
passenger/crew doors and for the forward and aft cargo doors. It also
supplies an aural warning if the door handle is lifted more than
specified angle when residual pressure is there in the aircraft.
- To monitor the position of all doors and to generate the ALL DOOR
status when all doors are in the closed position. It supplies this ALL
DOOR status to the Cabin Pressure Control System (CPCS) which
pressurizes the aircraft. The CPCS prevents cabin pressurization if
one of the monitored doors is in a condition that is not safe.
- To supply a visual indication on the passenger/crew doors, when the
slide is armed. It also supplies an aural warning if the door handle is
lifted more than a specified angle when the slide is armed.
The DSCS receives the doors and slides position data from proximity
sensors through the AFDX. The DSCS sends the slide
"armed/disarmed" status to the Control and Display System (CDS)
and the Flight Attendant Panel (FAP) for indication and warning. The
differential pressure switches send the data about the residual pressure
to the Autonomous Standby Power Supply Unit (ASPSU). The ASPSU
supplies the residual pressure indicators on the passenger/crew doors
and the forward and aft cargo doors.
The DSCS sends data to the CDAS through the AFDX.
Interface
The AFDX sends the indication supplied from the DSCS to the CDS
and to the FAP.

TP REV 2
DOORS AND SLIDES MANAGEMENT SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Doors and Slides Management System - Presentation
(continued)
The doors and slides status indications are available on the
DOOR/OXY page on the System Display (SD), on the CDS and also
on the FAP.
Residual pressure indicators are installed on the passenger/crew doors
and the forward and aft cargo doors. A buzzer that gives an aural
warning is installed on the passenger/crew doors only.
The slide armed warning-light and buzzer are installed on the
passenger/crew doors.

TP REV 2
DOORS AND SLIDES MANAGEMENT SYSTEM - PRESENTATION - CONTROL AND INDICATING

TP REV 2

Maintenance
Safety Precautions
WARNING: DO NOT OPEN THE PASSENGER/CREW DOORS

WHILE THE RED WARNING LIGHT FLASHES. IF
THE RED WARNING LIGHT FLASHES,
REMAINING PRESSURE IN THE CABIN CAN
CAUSE THE DOOR TO OPEN SUDDENLY AND
CAN:
- KILL OR CAUSE INJURY TO PERSONS
- CAUSE DAMAGE TO THE AIRCRAFT.
DO NOT OPEN THE CARGO-COMPARTMENT
DOORS WHILE THE RED WARNING LIGHT
FLASHES. IF THE RED WARNING LIGHT
FLASHES, REMAINING PRESSURE CAN CAUSE
THE DOOR TO OPEN SUDDENLY AND KILL OR
CAUSE INJURY TO PERSONS OR CAUSE DAMAGE
TO THE AIRCRAFT.

TP REV 2
MAINTENANCE - SAFETY PRECAUTIONS

TP REV 2
EQUIPMENT/FURNISHINGS SYSTEM PRESENTATION

Overview
The equipment and furnishings are, for example, seats, stowages and
emergency equipment which are installed for the comfort and safety of
the passengers and crew.
General familiarization training for this chapter focuses on:
- The cockpit
- The passenger compartment
- The galleys
- The lavatories
- The additional compartments
- The emergency equipment
- The rapid-decompression safety system.
VM25P1LEVEL0101_003 - Equipments and Furnishings Presentation Page 120

TP REV 2
OVERVIEW

TP REV 2

Cockpit - Presentation Location
Cockpit seats
Function/Description The seats for the captain and the F/O are classically installed on each
The cockpit is the compartment where the captain and the First Officer side of the center pedestal.
(F/O) sit. The seats for the other two occupants are in the aft area of the cockpit.
It contains equipment and furnishings that the crew use to fly the Cockpit equipment racks
aircraft. The consoles are installed on each side of the center pedestal and in
The cockpit compartment includes: the aft area of the cockpit.
- The cockpit seats Ancillary equipment
- The cockpit equipment racks The ancillary equipment is installed on each side of the center pedestal
- The ancillary equipment and in the aft area of the cockpit.
- The main avionics compartment (below the cockpit). Main avionics compartment
Cockpit seats The main avionics compartment is below the cockpit.
The cockpit contains four seats.
The seats for the captain and the F/O are symmetrical and each has
electrical and mechanical control for seat position adjustment. Cockpit seats
The seat for the third occupant only has a mechanical control. The electrical controls for the captain's seat and the F/O's seat are
The folding seat for the fourth occupant has no adjustment function. installed on the seat pan.
Cockpit equipment racks The mechanical controls for the captain's seat and the F/O's seat are
The cockpit equipment racks usually contain equipment such as: installed on the seat pan and on the backrest.
Consoles for the pilots and the other two occupants. The third occupant seat is the same as the pilots' seats but the seat
The consoles have different stowages and contain emergency controls are only mechanical.
equipment.
It is possible to remove them for maintenance.
Ancillary equipment
The ancillary equipment is special equipment such as:
Two sliding tables with integrated keyboard, two Electronic Flight
Bag (EFB) docking stations and the Onboard Maintenance Terminal
(OMT).
It is possible to remove it for maintenance.
Main avionics compartment
The main avionics compartment is a pressurized compartment that
contains most of the avionics equipment on racks.

TP REV 2
COCKPIT - PRESENTATION - FUNCTION/DESCRIPTION ... CONTROL AND INDICATING

TP REV 2

They are part of the passenger supply channels.
Passenger Compartment - Presentation It is possible to remove them for maintenance or to quickly change
the configuration of the cabin.
The passenger compartment includes: Location
- The passenger compartment seats The passenger compartment is the part of the aircraft where the
- The cabin attendant seats passengers sit.
- The linings and furnishings Passenger compartment seats
- The Overhead Stowage Compartments (OHSCs) The passenger compartment seats are installed all along the cabin.
- The Passenger Service Units (PSUs). Cabin attendant seats
Passenger compartment seats The cabin attendant seats are installed in the cabin at door areas.
These seats are installed in rows on the cabin floor structure as single Linings and furnishings
seats or in groups of two or three seats. The basic seat configuration The linings and furnishings are installed on the ceiling and on the side
is 2-2-2 for the business class and 3-3-3 for the economy class. of the cabin.
It is possible to remove them for maintenance or to quickly change OHSCs
the configuration of the cabin. The OHSCs are installed on the side and center areas of the cabin
Cabin attendant seats ceiling.
These seats retract automatically and are attached to the seat tracks, PSUs
to the cabin floor structure or to the lavatory, galley or stowage walls. The PSUs are installed above passenger and cabin crew seats.
Linings and furnishings
The linings and furnishings are panels that keep the fuselage structure,
the insulation and electrical or air conditioning components out of
view.
The linings and furnishings (ceiling, sidewall and dado panels, lighting
covers, linings) are all made of composite material and/or plastic.
It is possible to remove them for maintenance.
OHSCs
The OHSCs are used for the stowage of passenger hand luggage and
emergency equipment.
The OHSCs are retractable; it is possible to remove them for
maintenance or to quickly change the configuration of the cabin.
PSUs
The PSUs supply services and safety-related data such as oxygen,
attendant call to the passengers and the cabin crew.

TP REV 2
PASSENGER COMPARTMENT - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

Galleys - Presentation
The galley is a module where the cabin crew usually keeps food,
drinks, trolleys, containers and unwanted or used materials.
It is also the work area where the cabin crew can prepare meals and
drinks.
There are two types of galleys:
- A wet galley is connected to other aircraft systems (potable water
and waste system, electrical system and supplemental cooling system)
and is used to prepare and store food and drinks and to store trolleys
and containers.
- A dry galley is used only for storage of food, drinks, trolleys and
containers.
It is possible to remove the galley modules for maintenance or to
change the configuration of the cabin for some of them.
Location
The galley modules are installed in different areas of the cabin.
There are two types of galley location, fixed and flexible.
The galleys in fixed locations are installed in the forward and aft areas
of the cabin.
The galleys in flexible locations are installed in the forward/mid
forward and aft/mid aft areas of the cabin.
Interface
The electrical GAlley INsert equipment (GAIN) system of the wet
galleys has an interface through the Cabin Intercommunication Data
System (CIDS) to the Onboard Maintenance System (OMS). This
makes it possible to do the troubleshooting of the GAIN equipment.

TP REV 2
GALLEYS - PRESENTATION - FUNCTION/DESCRIPTION ... INTERFACE

TP REV 2

Lavatories - Presentation
The lavatory assembly is made of an integrated floor pan, sidewalls
and a ceiling.
It is possible to remove the lavatory modules for maintenance or to
change the configuration of the cabin.
The equipment is, for example, a toilet bowl and shroud with seat and
cover, a mirror, a washbasin and a baby nursing table.
Location
The lavatory modules are installed in different areas of the cabin.
There are two types of lavatory location, fixed and flexible.
The lavatories in fixed locations are installed in the forward and aft
areas of the cabin.
The lavatories in flexible locations are installed in the forward/mid
forward and aft/mid aft areas of the cabin.
The lavatory equipment is installed in the lavatory.

TP REV 2
LAVATORIES - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

Additional Compartments - Presentation
The additional compartments are installed for the flight and cabin
crew as an option.
These compartments are the Flight Crew Rest Compartment (FCRC)
and the Cabin Crew Rest Compartment (CCRC).
The crew members use these compartments for rest during long flights.
The compartments may have seats, bunks and a coat stowage.
Location
The additional compartments are installed in the cabin.
The FCRC is installed in the forward top area of the cabin.
The CCRC is installed in the aft top area of the cabin.

TP REV 2
ADDITIONAL COMPARTMENTS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

The miscellaneous emergency equipment is equipment such as a
Emergency - Presentation megaphone, crash axe or flashlight, which the crew can use in an
emergency.
Floatation and survival equipment
The emergency equipment is installed for the safety of the passengers The floatation and survival equipment help the passengers and crew
and the crew if an emergency occurs during the flight. members to stay on the water surface during an emergency over water.
The emergency equipment includes: The floatation and survival equipment are the escape-slides/rafts and
- The cockpit escape facilities other survival equipment such as life vests.
- The cabin escape facilities Supplementary medical equipment
- The first aid equipment The supplementary medical equipment is additional equipment, which
- The miscellaneous emergency equipment the crew can use in a medical emergency.
- The floatation and survival equipment The supplementary medical equipment is usually an emergency
- The supplementary medical equipment. medical kit, for example defibrillator, doctor kit, etc.
Cockpit escape facilities Emergency Locator Transmitter (ELT)
The cockpit escape facilities include an evacuation hatch and an escape The function of the ELT system is to transmit distress and location
rope, which is always attached to the aircraft structure. signals in an emergency situation. This helps search and rescue
If it is not possible to use the cockpit door in an emergency, the flight personnel to identify the aircraft and to find its location.
crew can use the rope to evacuate the cockpit after opening of the Two systems are installed in the aircraft:
emergency escape hatch. - An automatic fixed ELT connected to a dedicated transmission
Cabin escape facilities antenna
The cabin escape facilities are evacuation systems that let the - One or more portable ELTs fitted with their own antenna.
passengers and crew members go out of the aircraft quickly in an Automatic fixed ELT
emergency. The fixed ELT can be activated:
The cabin escape facilities have dual-lane or single-lane inflatable - either manually by the crew through dedicated switches either in the
escape-slides that are also used as rafts after an evacuation, when the cockpit or on the ELT
aircraft is in a ditching condition. - or automatically in case of important deceleration event (crash, big
First aid equipment impact, etc.).
The crew can use the first aid equipment to give medical aid to Portable ELT
passengers or crew members who become ill or have small injuries The portable ELT can only be activated manually by the crew in case
during flight. of emergency. Activation is made by a dedicated switch on the ELT.
The first aid equipment is usually a self-contained first-aid kit.
Miscellaneous emergency equipment
The miscellaneous emergency equipment helps the crew to give aid
to the passengers if an emergency occurs.

TP REV 2
EMERGENCY - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

Emergency - Presentation (continued)
Location
The emergency equipment is usually installed in standard locations
on the aircraft but other locations are also possible.
Cockpit escape facilities
The cockpit escape hatch is an emergency exit located on the cockpit
ceiling.
The escape rope is kept in a dedicated stowage compartment adjacent
to the escape hatch.
Cabin escape facilities
The cabin escape facilities are installed on each passenger door of the
aircraft.
Passenger doors that are type A emergency exits have dual-lane
slide/rafts.
Type C emergency exits have single-lane slide/rafts.
Passenger doors 2 and 4 are always type A emergency exits, but
passenger doors 1 and 3 can be a type A or a type C emergency exit.
In the standard configuration, passenger door 1 has a single-lane
slide/raft and doors 2, 3 and 4 have dual-lane slide/rafts.
Floatation and survival equipment
The floatation and survival equipment is installed at each door and in
different locations on the aircraft.
The life vests are below or near the passenger compartment seats, the
cabin attendant seats and the cockpit seats.
Emergency Locator Transmitter (ELT)
The automatic fixed ELT is located in the aft top section of the aircraft
fuselage.
Portable ELTs can be installed at several aircraft locations (example:
overhead compartments, doghouse, etc.)

TP REV 2
EMERGENCY - PRESENTATION - LOCATION

TP REV 2

Emergency - Presentation (continued)
The automatic fixed ELT can be manually activated through the:
- ELT remote control panel on the overhead panel
- ELT control panel on the ELT.

TP REV 2
EMERGENCY - PRESENTATION - CONTROL AND INDICATING

TP REV 2

Rapid Decompression Safety System - Presentation
The rapid-decompression safety system balances the pressure between
the cockpit, the cabin and the cargo compartments if a decompression
occurs.
The rapid-decompression safety system includes blow-in and blow-out
rapid-decompression panels, flaps and the cockpit door.
Location
The rapid-decompression safety system includes:
- A decompression panel in the lower part of the cockpit door
- Decompression panels in the lower sidewall/dado panels of the
passenger compartment
- Decompression panels in the sidewall and ceiling panels of the cargo
compartment.

TP REV 2
RAPID DECOMPRESSION SAFETY SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2
CABIN PRESENTATION
Cabin Presentation
VM25P2LEVEL0101_002 - Cabin Presentation Page 140

TP REV 2
CABIN PRESENTATION
VM25P2LEVEL0101_002 - Cabin Presentation Page 141

TP REV 2
CARGO & ACCESSORY COMPARTMENTS SYSTEM PRESENTATION

Overview
The cargo compartments contain the Unit Load Devices (ULDs) and the
equipment and hold them in a safe position during the flight.
The Cargo Loading Systems (CLSs) move the ULDs into and out of the
cargo compartments.
- The cargo compartments
- The lower-deck cargo-loading systems
- The accessory compartments.
VM50P1LEVEL0101_002 - Cargo compartment Presentation Page 142

TP REV 2
OVERVIEW

TP REV 2

Cargo Compartments - Presentation
The cargo compartments include:
- The lower-deck cargo compartments
- The lower-deck cargo-compartment drainage-system.
The cargo compartments hold the ULDs in the forward, aft and bulk
areas of the aircraft. All cargo compartments have fireproof walls,
floors, ceilings, sidewall panels and decompression panels to retard
fire and smoke propagation. If there is smoke, each compartment is
fully sealed when the doors are closed. This makes sure that the fire
or smoke in one compartment cannot go to another compartment.
The drainage system collects unwanted fluids from the cargo
compartment floors and drains them through a network of pipes into
the bottom of the fuselage. The fluids then go to the bilge drain valves.
Location
The cargo compartments are installed in the lower-deck forward, aft
and bulk areas of the aircraft.

TP REV 2
CARGO COMPARTMENTS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

Lower-Deck Cargo-Loading Systems - Presentation
The lower-deck CLSs move and latch the ULDs in the forward and
aft cargo-compartments. The lower-deck CLSs have mechanical and
electrical components that move, align and control the ULDs.
The electrical CLSs include the Power Drive Units (PDUs). The inside
control panels and the outside control panels are connected to the
control boxes to control the PDUs. The control boxes also monitor
the PDUs.
The mechanical CLSs include the guides, the tracks, the ballmats and
the latches. There are different latches that safety the ULDs and hold
them in position. You can engage and disengage the latches manually.
Interface
Each control box has an interface with the Onboard Maintenance
System (OMS) for trouble shooting.

TP REV 2
LOWER-DECK CARGO-LOADING SYSTEMS - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Lower-Deck Cargo-Loading Systems - Presentation (continued)
Location
There is an inside control panel in the forward cargo compartment
and also in the aft cargo compartment. An outside control panel is on
the external skin of the aircraft adjacent to the cargo compartment
doors for each of these compartments.
There are two control boxes. One is installed in the forward cargo
compartment and one in the aft cargo compartment.
These controls are installed:
- Two control panels adjacent to the door of the forward cargo
compartment
- Two control panels adjacent to the door of the aft cargo compartment.

TP REV 2
LOWER-DECK CARGO-LOADING SYSTEMS - PRESENTATION - LOCATION & CONTROL AND INDICATING

TP REV 2

Accessory Compartments - Presentation
The accessory compartments include:
- The wheel wells
- The additional avionics compartment
- The miscellaneous compartments (air conditioning compartment,
hydraulic compartment, waste tank area).
The accessory compartments can contain the equipment for the
In-Flight Entertainment System (IFE), the retracted landing gears, the
packs, the hydraulics and other equipment.
Location
The wheel wells are installed in the nose landing-gear and in the main
landing-gear areas.
The air conditioning compartment is installed forward of the main
landing-gear.
The hydraulic compartment is installed between the main
landing-gears.
The waste tank area is aft of the bulk cargo compartment.
The additional avionics compartment is installed between the bulk
cargo compartment and the waste tank area.

TP REV 2
ACCESSORY COMPARTMENTS - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2
FLIGHT CONTROLS SYSTEM PRESENTATION

Overview
- PFCS
- Aileron
- Spoiler
- Elevator
- THS
- Rudder
- Lift augmenting
- Flaps.
VM27P1LEVEL0101_003 - Flight Controls System Presentation Page 152

TP REV 2
OVERVIEW

TP REV 2

- Three SECondary Computers (SECs)
Primary Flight Control System (PFCS) - Presentation - One Backup Control Module (BCM)
- Two Flight Control Data Concentrators (FCDCs) which are a Core
Processor Input/Output Module (CPIOM) application for
The function of the PFCS is: indicating/interface functions
- To compute the flight control laws and their related functions. - Local computation (for servoloop function) ensured by Flight Control
- To give the surface deflection orders and do the servoing and Remote Module (FCRM) or electronic module installed on actuators.
monitoring of the flight control surfaces in normal, abnormal and The computation part sends data to:
emergency conditions. The flight control surfaces are: - The Control and Display System (CDS) for system indicating through
- Two pairs of ailerons used for roll control the FCDCs
- Seven pairs of spoilers used for speedbrake function and lift damping - The Flight Warning System (FWS) for crew alerts through the
on ground (ground spoilers), including five pairs used for roll control FCDCs
- One rudder used for yaw control - The Onboard Maintenance System (OMS) through the FCDCs, for
- One pair of elevator used for pitch control subsequent maintenance.
- One THS used for pitch-trim control The actuation part
- Two pairs of flaps for high-lift control The actuation part moves the control surfaces. It receives command
- Lift augmenting (one pair of droop-nose device and six pairs of slats) orders from the PRIMs and SECs.
for high-lift control. If the PRIMs and SECs are not serviceable or if the main electrical
General architecture power supply is not available, the actuation part receives command
The general architecture has three main parts: orders from the BCM.
- Control Laws and Related Functions
- Computation The PRIMs and SECs have two functions:
- Actuation. - Computation of the flight control laws (including protections) and
The control part includes: - Execution (servoing and monitoring of the related control surfaces).
- Side Stick Units (SSUs) There are three control law levels:
- Rudder pedals - Normal (all the protections are available)
- Automatic Flight System (AFS) - Alternate (some protections are decreased or not available)
- Speedbrake control lever - Direct (no protections available).
- PITCH TRIM control switches The flight control laws are automatically switched from normal to
- RUDDER TRIM control switch. alternate and then to direct in relation to the type and number of
The control part sends signals to the computation part to generate failures.
command orders. The PRIMs and SECs receive orders from the cockpit controls or the
The computation part includes: AFS. With reference to the current aircraft attitude, the computation
- Three PRIMary Computers (PRIMs)

TP REV 2
function changes these orders to an aircraft objective and generates

the surface deflection orders necessary to go to the computed aircraft
objective. The computation function compares the reached aircraft
attitude with the computed aircraft objective.
In normal operation, one PRIM only (called "MASTER") does the
computation function.
The master PRIM generates the surface deflection orders and sends
them:
- To its dedicated actuators and
- To the two other PRIMs and to the three SECs to move their
dedicated actuators.

TP REV 2
PRIMARY FLIGHT CONTROL SYSTEM (PFCS) - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

TP REV 2

TP REV 2

The EBHA EM has the same function as the EHA.
Actuators - Presentation
C
onventional servocontrols
The conventional servocontrols have:
- A hydraulic block connected to one aircraft hydraulic system
- A FCRM that controls a servo module to extend or retract the actuator
and performs the actuator servoloop function (control and feedback).
- A hydraulic jack
- A mode selector valve.
Electro-Hydrostatic Actuators (EHAs)
The EHAs generate their hydraulic pressure and are used when there
is loss of the normal aircraft hydraulic pressure.
The EHAs have:
- A hydraulic block
- An Electronic Module (EM) that controls the electric motor pump
and performs the servoloop function (control and feedback)
- An electric motor pump, to extend or retract the actuator piston rod
- A hydraulic jack
- An accumulator
- A mode selector valve.
The electric motor and the hydraulic pump receive orders from the
EM/flight control computers (PRIMs and SECs) to extend or retract
the actuator.
Electrical Backup Hydraulic Actuators (EBHAs)
The EBHAs have a conventional servocontrol part and an EHA part
that control a same hydraulic actuator.
In normal operation mode, the EBHA operates as a conventional
servocontrol that uses aircraft hydraulic pressure to move the actuator
rod. If there is loss of aircraft hydraulic pressure, the EBHA operates
as an EHA, that generates its hydraulic pressure to move the actuator
rod.

TP REV 2
ACTUATORS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

Through the Avionics Full Duplex Switched Ethernet (AFDX) network
Aileron - Presentation the PRIMs and SECs send data related to the aileron actuators to the
CPIOMs (FCDC application) and then to the CDS.
The ailerons have these functions:
- Roll control
- Lift control (aileron droop)
- Lift dumping on ground (ground spoilers).
Ailerons - Architecture
There are two ailerons on each wing, operated by actuators. The aileron
actuators are electrically controlled and monitored by the PRIMs and
SECs from:
- The speedbrake control lever
- The SSUs
- The AFS or
- The Slat Flap Control Computers (SFCCs).
There are two types of ailerons:
- The outboard ailerons are operated by two conventional
servocontrols.
- The inboard ailerons are operated by a conventional servocontrol or
by an EHA.
In normal conditions, each servocontrol and each EHA are controlled
and monitored through the PRIMs and SECs.
Actuator position feedback is sent to the FCRM or electronic module
for servoloop computation.
Surface and actuator position feedback is sent to the PRIMs and SECs
for monitoring.
In emergency conditions, the inboard aileron servocontrols are
controlled through a BCM, from the SSUs.
Interface
The ailerons have interfaces with the Yellow and Green hydraulic
systems to supply hydraulic power to the aileron servocontrols and
with electrical system to supply electrical power to EHA.

TP REV 2
AILERON - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Spoiler - Presentation
The spoilers have these functions:
- Roll assistance
- Speedbrake
- Lift dumping on ground (ground spoilers)
- Adaptive Droop Hinge Flap (ADHF) through interface with SFCCs
in order to control the gap between spoilers and flaps when flaps are
extended.
Spoiler - Architecture
There are seven spoilers on each wing operated by actuators. Each
spoiler actuator is electrically controlled and monitored by the PRIMs
and SECs from:
- The speedbrake control lever
- The SSUs or
- The AFS
- The SFCCs (for ADHF).
All spoilers are hydraulically operated by conventional servocontrols
but not spoiler 5 which is operated by an EBHA. Each
servocontrol/EBHA is controlled and monitored by the PRIMs and
SECs.
Interface
The spoilers have interfaces with the Yellow and Green hydraulic
systems to supply hydraulic power to the spoiler actuators and with
electrical system to supply electrical power to EBHA.
Through the AFDX network, the PRIMs and SECs send data related
to the spoiler actuators to the CPIOMs (FCDC application) and then
to the CDS.

TP REV 2
SPOILER - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Elevator - Presentation
The elevators give pitch control of the aircraft.
There are two elevators, one on each side, operated by actuators. The
elevator actuators are electrically controlled and monitored by the
PRIMs and SECs from the SSUs or the AFS. Each surface is operated
by one conventional servocontrol and one EHA.
In normal conditions, each actuator is controlled and monitored by
the PRIMs and SECs.
Actuator position feedback is sent to the FCRM or electronic module
for monitoring.
In emergency conditions, the conventional servocontrols are controlled
and monitored by a BCM from the SSUs or the PITCH TRIM control
switches.
Interface
The elevator has interfaces with the Yellow and Green hydraulic
systems to supply hydraulic power to the elevator conventional
servocontrols and with electrical system to supply electrical power to
EHA.
to the elevators/actuators to the CPIOMs (FCDC application) and then
to the CDS.

TP REV 2
ELEVATOR - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Trimmable Horizontal Stabilizer (THS) - Presentation
The THS gives pitch control and pitch trim control of the aircraft.
There is one surface operated by actuator. The THS actuator is
electrically controlled and monitored by the PRIMs and SECs pitch
trim function.
The THS actuator has two electric motors, a screwjack and a ball nut.
The two independent electric motors are controlled and monitored by
the PRIMs and SECs. Each computer receives command signals from
the SSUs or the AFS for the autotrim function or from the PITCH
TRIM control switches for the manual trim function via Electric Motor
Control Unit (EMCU).
Interface
to the THS actuator to the CPIOMs (FCDC application) and then to
the CDS.

TP REV 2
TRIMMABLE HORIZONTAL STABILIZER (THS) - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

- Turn coordination
Rudder - Presentation - Dutch roll damping
- Rudder trim
Function/Description - A350-900 Only
- Aircraft guidance on the ground (during takeoff and rollout).
The rudder controls the aircraft in the yaw axis. There is one rudder operated by actuators. The rudder actuators are
The rudder gives: electrically controlled and monitored by the PRIMs and SECs from
- Yaw control the rudder pedals, the SSUs (for turn coordination), the AFS or the
- Turn coordination rudder trim.
- Dutch roll damping The rudder is operated by two conventional servocontrols and one
- Rudder trim EHA.
- Aircraft guidance on the ground (during takeoff and rollout). In normal conditions, each servocontrol/EHA is controlled and
There is one rudder operated by actuators. The rudder actuators are monitored by the PRIMs and SECs.
electrically controlled and monitored by the PRIMs and SECs from The pilot commands the rudder trim with the RUDDER TRIM control
the rudder pedals, the SSUs (for turn coordination), the AFS or the switch through the PRIMs and SECs. Then, the PRIMs and SECs give
rudder trim. orders through the Rudder and Brake Pedal Unit (RBPU) to move the
The rudder is operated by two conventional servocontrols and one rudder pedals. The rudder is then moved to a new neutral position.
EHA. Actuator position feedback is sent to the FCRM or electronic module
In normal conditions, each servocontrol/EHA is controlled and for servoloop computation.
monitored by the PRIMs and SECs. Surface and actuator position feedback is sent to the PRIMs and SECs
The pilot commands the rudder trim with the RUDDER TRIM control for monitoring.
switch through the PRIMs and SECs. Then, the PRIMs and SECs give In emergency conditions, the top servocontrol actuator is controlled
orders through the Pedal Feel and Trim Unit (PFTU) to move the and monitored by a BCM from the rudder pedals through the RBPU.
rudder pedals. The rudder is then moved to a new neutral position.
Actuator position feedback is sent to the FCRM or electronic module Interface
for servoloop computation. The rudder has interfaces with the Yellow and Green hydraulic systems
Surface and actuator position feedback is sent to the PRIMs and SECs to supply hydraulic power to the rudder servocontrols and with
for monitoring. electrical system to supply electrical power to EHA.
In emergency conditions, the top servocontrol actuator is controlled Through the AFDX network, the PRIMs and SECs send data related
and monitored by a BCM from the rudder pedals through the PFTU. to the rudder actuators to the CPIOMs (FCDC application) and then
to the CDS.
Function/Description - A350-1000 Only
The rudder controls the aircraft in the yaw axis.
The rudder gives:
- Yaw control

TP REV 2
RUDDER - PRESENTATION - FUNCTION/DESCRIPTION - A350-900 ONLY ... INTERFACE

TP REV 2
RUDDER - PRESENTATION - FUNCTION/DESCRIPTION - A350-900 ONLY ... INTERFACE

TP REV 2

TP REV 2

Through the AFDX network, the SFCCs send data related to the lift
Lift Augmenting - Presentation augmenting actuators to the CDS.
The slat system operates together with the flap system to give high-lift
control of the aircraft.
Each wing has one droop-nose device and six slats to give more lift
to the aircraft.
The slats and droop-nose actuation and power-transmission system
controls the movement of the droop-nose devices and slats during:
- Takeoff
- Approach
- Landing.
The lift augmenting operation is electrically controlled and monitored
by two SFCCs. This operation is also hydro-mechanically and
electro-mechanically controlled through a Power Control Unit (PCU),
actuators and transmission shafts.
The slat/flap control lever gives commands to the SFCCs which
transmit orders to the PCU to move the surfaces. The PCU moves
each slat section through two rotary actuators and transmission shafts.
The slat PCU has:
- One hydraulic motor (Yellow system)
- One electric motor
- One differential gearbox.
The differential gearbox changes hydraulic and electrical energy into
mechanical energy to drive the slat transmission system.
Wing Tip Brakes (WTBs) can lock the system if there is mechanical
failure/rupture. Monitoring is provided by sensors.
The SFCCs monitor (through sensors) and control the PCU and the
WTBs.
Interface
The lift augmenting function has interfaces with the Yellow hydraulic
system and electrical system to supply the PCU motors.

TP REV 2
LIFT AUGMENTING - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Flaps - Presentation
The flaps give lift augmenting, variable camber and differential flap
setting.
Flaps - Architecture
Each wing includes one inboard and one outboard flap section. The
flap operation is controlled and monitored by the two SFCCs. This
operation is actuated through a PCU, transmission shafts, actuators
and two ADGBs.
The flap/slat control lever gives commands to the SFCCs which
transmit orders to the PCU and ADGBs to move the surfaces. The
PCU and ADGBs move each flap surface through transmission shafts
and two rotary actuators.
The flap PCU has:
- Two hydraulic motors (Green and Yellow hydraulic systems)
- One differential gearbox.
The differential gearbox changes hydraulic and electrical energy into
mechanical energy to drive the flap transmission system.
Each transmission shaft end has a WTB which can lock the system if
there is mechanical failure/rupture. Monitoring is provided by sensors.
Two Active Differential Gearboxes (ADGBs) between the inboard
and outboard flap transmissions give the differential flap setting. With
the ADGBs, the outboard flaps can move independently from the
inboard flaps.
The PCU, WTBs and ADGBs are controlled and monitored by the
SFCCs.
Flaps - Principle
The variable camber function is a small extension of the two inboard
and outboard flaps in cruise that reduce aircraft drag.
The differential flap setting function is a differential extension between
the inboard and outboard flaps that decreases wing loads and alleviates
wing bending.

TP REV 2
FLAPS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2
FLAPS - PRESENTATION - FUNCTION/DESCRIPTION

TP REV 2

TP REV 2

Flaps - Presentation (continued)
Interface
The flaps have interfaces with the Yellow and Green hydraulic systems
to supply the flap PCU motors and with electrical system to supply
electrical power to ADGB.
Through the AFDX network, the SFCCs send data related to the flaps
to the CDS.

TP REV 2
FLAPS - PRESENTATION - INTERFACE

TP REV 2

Location - Presentation
The three PRIMs and the three SECs are installed in the avionics
compartment.
The BCM is located in the lower deck forward cargo compartment.
The two SFCCs are located in the avionics compartment.

TP REV 2
LOCATION - PRESENTATION

TP REV 2

Controls
- PRIM and SEC pushbutton switches
The PRIM and SEC pushbutton switches are on the overhead panel.
- SSU and rudder pedals
One SSU is on the CAPT console, the other one is on the F/O console.
The rudder is controlled through the CAPT and F/O rudder pedals.
- Speedbrake control lever
The speedbrake control lever is on the center pedestal.
- RUDDER TRIM control switch
The RUDDER TRIM control switch is on the center pedestal.
- PITCH TRIM control switches
The PITCH TRIM control switches are on the center pedestal.
- Slat/flap control lever
The slat/flap control lever is on the center pedestal.
Indicating
The flight control data is shown on these display units:
- The System Display (SD)
- The lower part of the CAPT and F/O Primary Flight Displays (PFDs).

TP REV 2

TP REV 2
OXYGEN SYSTEM PRESENTATION

Overview
The oxygen system has these subsystems:
- Crew oxygen
- Passenger oxygen
- Portable oxygen.
The function of the crew oxygen is:
- To supply oxygen to two flight crews and two observers during
decompression
- To give protection against the smoke and/or toxic gas in the cockpit.
The function of the passenger oxygen is to supply oxygen to passengers
and cabin occupants during cabin decompression.
The function of the portable oxygen system is:
- To give more oxygen to the passengers after cabin decompression, if
more oxygen is necessary
- To give protection to the flight crew and cabin crew during fire fighting.
VM35P1LEVEL0101_003 - Oxygen System Presentation Page 186

TP REV 2
OVERVIEW

TP REV 2

If two oxygen cylinders are installed in one oxygen compartment, a
Crew Oxygen - Presentation dual distribution manifold is necessary.
Function/Description Interface
The crew oxygen has two equivalent subsystems: The crew oxygen control and indicating for the two subsystems has
- The LH subsystem supplies oxygen to the CAPT and one observer two Oxygen System Control and Monitoring (OSCM) software which
(4th occupant) monitor and supply data to other system.
- The RH subsystem supplies oxygen to the F/O and one observer The crew oxygen control and indicating in each subsystem includes:
(3rd occupant). - A crew shut-off valve to start the crew oxygen system
When the crew oxygen is in operation, each subsystem operates at - The pressure and temperature sensors that are used by the OSCM
the same time. for cockpit indication.
Crew Oxygen Storage
The crew oxygen storage in each subsystem includes:
- An oxygen cylinder-reducer assembly that keeps the high-pressurized
oxygen and lets the oxygen flow to the crew oxygen distribution,
when the system operates
- A ventilated oxygen compartment that keeps the oxygen
cylinder-reducer assembly in position and discharges overboard any
leak inside the compartment.
If a leak occurs in the oxygen compartment, a venturi lets the high
concentration of oxygen in the oxygen compartment flow overboard.
For the crew oxygen storage, it is optional to install:
- A second oxygen-reducer assembly in the same oxygen compartment
- An in-situ refilling with a fill panel and a fill port.
Crew Oxygen Distribution
The crew oxygen distribution in each subsystem includes:
- Two full-face quick-donning oxygen-masks (referred to as "the
mask") that supplies oxygen and also give protection to the flight crew
- Two oxygen mask stowage-boxes (referred to as "stowage box") to
keep the masks
- A single oxygen manifold to supply oxygen from the oxygen
cylinder-reducer assembly to the related user
- An overboard discharge indicator to release the pressure, if
overpressure occurs.

TP REV 2
CREW OXYGEN - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Crew Oxygen - Presentation (continued)
Location
The two oxygen compartments are located in the FWD cargo
compartment:

TP REV 2
CREW OXYGEN - PRESENTATION - LOCATION

TP REV 2

Passenger Oxygen - Presentation
The passenger oxygen system is a decentralized system with either a
chemical or a gaseous oxygen source. The interfaces to the aircraft
and the aircraft wiring are identical for both cases.
The basic passenger oxygen system is the chemical oxygen system.
It is also possible to have a passenger oxygen system with:
- A higher amount of chemical oxygen in the storage
- A decentralized passenger oxygen system with a gaseous oxygen
source able to cover all high terrain profiles.
For manual opening of oxygen container, the cabin crew can open the
oxygen container with a manual release tool.
Interface
The passenger oxygen system operates automatically if it receives
signals from the Cabin Pressure Control System (CPCS) and from the
atmospheric pressure transducer.
The flight crew can also start the passenger oxygen system manually
with the MASK MAN ON push button on the ICP panel.

TP REV 2
PASSENGER OXYGEN - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Passenger Oxygen - Presentation (continued)
Location
The passenger oxygen containers are installed at these locations in
the cabin:
- Above the passenger seats
- Near the cabin attendant seats
- In the lavatories
- In the galley working areas
- In the crew rest compartments and in other separated areas.

TP REV 2
PASSENGER OXYGEN - PRESENTATION - LOCATION

TP REV 2

Portable Oxygen - Presentation
The portable oxygen system includes:
- Portable oxygen cylinder assemblies
- Portable Breathing Equipment (PBE) in the cabin and cockpit.
The function of the portable oxygen cylinder assemblies is:
- To supply more oxygen to the passengers for first aid function
- To supply oxygen to the cabin crew when the cabin crew moves in
the cabin during a cabin decompression.
The function of the PBE is to give protection to the flight crew and
the cabin crew for fire fighting.
Location
The equipment for the portable oxygen is single equipment that is
installed in different locations in the cabin and in the cockpit.

TP REV 2
PORTABLE OXYGEN - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

The OXYGEN control panel for the crew and passenger systems is on
the cockpit overhead panel. The CREW SUPPLY pushbutton switch in
ON position lets the oxygen flow from the oxygen cylinders to the crew
masks. The MASK MAN ON pushbutton electrically controls the opening
of the oxygen container doors, by manual operation.
Passenger "SYS ON" light illuminates, when the passenger oxygen system
is in operation.
The crew oxygen system status is then shown on the upper right corner
of the DOOR/ OXY ECAM Page. For the LH side of the crew oxygen
system, the status is shown in the "CAPT" side. For the RH side of the
crew oxygen system, the status is shown in the "F/O" side.
Each overboard discharge line has an overboard discharge indicator which
gives an indication if the oxygen is released overboard. These indicators
are located at LH side and RH side, on FWD section of the aircraft.

TP REV 2

TP REV 2
WATER/WASTE SYSTEM PRESENTATION

Overview
The water and waste system supplies potable water, removes the waste
and discards the waste water.
- Potable water
- Toilet system
- Waste water drain.
VM38P1LEVEL0101_003 - Water/Waste System Presentation Page 200

TP REV 2
OVERVIEW

TP REV 2

Potable Water - Presentation
The potable water system supplies pressurized potable water from
two potable water tanks to the lavatories and to the galleys. The
pneumatic system supplies bleed air through the air supply system to
pressurize the potable water tanks. Also, an electrical water boost
pump increases this pressure to the necessary supply pressure in the
water line. On the ground, through a ground air connection, it is also
possible to pressurize the potable water tanks.
A potable-water treatment module keeps the risk of microbiological
contamination of the potable water to the minimum.
The primary control of the filling and draining procedures is from the
Potable Water Indication Panel (PWIP) of the Potable Water Service
Panel (PWSP).
System servicing (filling and draining) is only possible when electrical
power is available. But if electrical power is not available, it is possible
to do servicing manually. Then only maintenance personnel can do
this servicing.
The PWIP controls and monitors the potable water system.
The Flight Attendant Panel (FAP) shows the level of potable water
in the potable water tanks. It also makes it possible to pre-select the
fill level.
The potable-water system function hosted in the Cabin
Intercommunication Data System (CIDS) directors is the interface
between the FAP and the system.
Interface
The potable water system has an interface with the CIDS through the
FAP and the CIDS directors.
The potable water system has also an interface with the pneumatic
system.

TP REV 2
POTABLE WATER - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Potable Water - Presentation (continued)
Location
The two potable water tanks are in the aft-cabin underfloor area.

TP REV 2
POTABLE WATER - PRESENTATION - LOCATION

TP REV 2

Toilet System - Presentation
The toilet system moves waste from the toilets and the Galley Waste
Disposal Units (GWDUs) to the waste tanks.
The toilet system has two separate subsystems, the left and the right
toilet subsystems. Each subsystem has one waste tank.
A vacuum transport system uses differential pressure to move the
toilet and GWDU waste through the flush valves to the waste tanks.
When this differential pressure is not sufficient, vacuum generators
supply the necessary negative pressure (vacuum).
The draining and flushing procedures of the waste tanks are possible
from the waste service panel.
The waste drain lines connect the waste tanks through the waste drain
valves to the waste service panel.
The vacuum generators are between the waste tanks and the outer
lower fuselage.
The Vacuum Toilet System (VTS) function hosted in the Cabin
Intercommunication Data System (CIDS) directors is the interface
between the FAP and the system.
The FAP shows the level of waste in the waste tanks.
Interface
The toilet system has an interface with the CIDS, through the FAP
and the CIDS directors.

TP REV 2
TOILET SYSTEM - PRESENTATION - FUNCTION/DESCRIPTION & INTERFACE

TP REV 2

Toilet System - Presentation (continued)
Location
The two waste tanks are in the aft-cabin underfloor compartment.

TP REV 2
TOILET SYSTEM - PRESENTATION - LOCATION

TP REV 2

Waste Water Drain - Presentation
The waste-water drain system removes waste water from the galley
sinks and lavatory washbasins. The waste water flows through the
drain valves and the drain lines to the heated drain masts.
The drain lines are between the galley sinks, the lavatory washbasins
and the drain masts.
Location
The drain valves are in the related galleys and lavatories (in the cabin).
The drain lines are between the cabin and the lower fuselage.

TP REV 2
WASTE WATER DRAIN - PRESENTATION - FUNCTION/DESCRIPTION & LOCATION

TP REV 2

These panels control the system:
- The FAP in the cabin
- The waste service panel and PWIP of the PWSP on the outer surface
of the aft lower fuselage.

TP REV 2

© AIRBUS SAS 2018. All rights reserved.
Confidential and proprietary document.
This document and all information contained herein is the sole property of
AIRBUS SAS. No intellectual property rights are granted by the delivery of
this document or the disclosure of its content. This document shall not be
reproduced or disclosed to a third party without the express written consent
of AIRBUS SAS. This document and its content shall not be used for any
purpose other than for which it is supplied. The statements made herein do
not constitute an offer. They are based on the mentioned assumptions and
are expressed in good faith. Where the supporting grounds for these
statements are not shown, AIRBUS SAS will be pleased to explain the basis
thereof.
AIRBUS, its logo, A300, A310, A318, A319, A320, A321, A330, A340, A350,
A380, A400M are registered trademarks.

A350 Technical Training Manual T1+T2 Mechanical and Avionics A350 RR TRENT XWB Airframe (Level1)

Uploaded by

Copyright:

Available Formats

A350 Technical Training Manual T1+T2 Mechanical and Avionics A350 RR TRENT XWB Airframe (Level1)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A350 Technical Training Manual T1+T2 Mechanical and Avionics A350 RR TRENT XWB Airframe (Level1)

Uploaded by

Copyright:

Available Formats

A350

TECHNICAL TRAINING MANUAL

Under no circumstances should this document be used as a reference.

It will not be updated.

All rights reserved

AIRBUS Environmental Recommendation.

Hydraulic Power System Presentation.....................................2

TABLE OF CONTENTS Page 1

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 2

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 3

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 4

MAIN HYDRAULIC POWER - PRESENTATION - FUNCTION DESCRIPTION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 5

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 6

MAIN HYDRAULIC POWER - PRESENTATION - LOCATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 7

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 8

AUXILIARY HYDRAULIC POWER - PRESENTATION - FUNCTION DESCRIPTION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 9

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 10

AUXILIARY HYDRAULIC POWER - PRESENTATION - LOCATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 11

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 12

HYDRAULIC SYSTEM MONITORING - PRESENTATION - FUNCTION DESCRIPTION & INTERFACE

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 13

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 14

CONTROL AND INDICATING - PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 15

HYDRAULIC POWER SYSTEM PRESENTATION

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 16

MAINTENANCE - TOOLS & MAINTENANCE PRACTICES

VM29P1LEVEL0101_002 - Hydraulic Power System Presentation Page 17

LANDING GEAR SYSTEM PRESENTATION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 18

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 19

LANDING GEAR SYSTEM PRESENTATION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 20

MAIN GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 21

MAIN GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 22

THIS PAGE INTENTIONALLY LEFT BLANK

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 23

LANDING GEAR SYSTEM PRESENTATION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 24

NOSE GEAR AND DOORS - PRESENTATION - FUNCTION/DESCRIPTION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 25

LANDING GEAR SYSTEM PRESENTATION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 26

EXTENSION AND RETRACTION - PRESENTATION - FUNCTION/DESCRIPTION

VM32P1LEVEL0101_004 - Landing Gear System Presentation Page 27

LANDING GEAR SYSTEM PRESENTATION