SPI & DPI Commands Slave Mode Notes: MV Setpoints

Copyright www.proscada.
com
SPI & DPI commands Slave mode notes
 If the Slave addresses of a Block are to be setpoints written by the master the Flag “Disable
Interrogation response” should be set in the block settings, otherwise the value is returned
as a Input during interrogation.
Actions that occur at Slave side during command write from the Master
1. Commands sent by the Master set the :VALUE bits & set the timestamp of local PC time of
receipt.
2. In addition the following bits are set: Bit 13 (:TOG) is toggled (changed) everytime a
command is received, this allows the SCADA to sense the command even if Master sends
the same value. Bit 12 (:WRIT) is set after first write, this may be used to indicated that a
value has been received by the slave since startup.
3. The OPC server sends a OnChange() with new timestamp even if the value does not
change.
4. For SPI & DPI commands: in the block settings set “Select timeout” to “0” if using direct
execute (not select execute). This timer is the select timeout time i.e. user needs to send
execute AFTER select within this time or execute fails. Do not set too long, if user fails to
cancel or tries to select another, will fail until timeout.
MV Setpoints
MV Setpoints Slave mode notes
 If the Slave addresses of a Block are to be setpoints written by the master the Flag “Disable
Interrogation response” should be set in the block settings, otherwise the value is returned
as an Input during interrogation.
Actions that occur during setpoint write:
5. Setpoints sent by the Master set the analog value & set the timestamp of local PC time of
receipt.
6. In addition the following status bits are set Bit 10 (:TOG) is toggled (changed) everytime a
command is received, this allows the SCADA to sense the command even if Master sends
the same value. Bit 12 (:WRIT) is set, this may be used to indicated that a value has been
received by the slave since startup.
7. The OPC server sends a OnChange() with new timestamp even if the value does not
change.
Format of Integrated totals (Counters)

The value returned by OPC address <rtu>:IT:<asdu>:<obj> is the count value. If the IEC data is
invalid the value is 0.
**Note for OPC please use this address “<rtu>:IT:<asdu>:<obj>|DWRD” this forces the datatype to
Double word.
Page 14 of 7
Copyright www.proscada.com
To read the IT Sequence number use the address “<rtu>:IT:<asdu>:<obj>|ITSQ
Counter Interrogation
Sending Counter interrogations is performed by writing to addesses <rtu>:IT:<asdu>:<obj> the

value of the bits 0-7 written are sent directly to the RTU.
Format of Step Position Information

The value returned by OPC address <rtu>:STP:<asdu>:<obj> is the VTI (value with transient state
as defined in IEC section 5.2.1.5).
VTI := CP8{Value,Transient}
Value := I7[1..7]<-64..+63>
Transient := BS1[8]
<0> := equipment is not in transient state

<1> := equipment is in transient state
Example 1: “RTU1:STP:1:22|S&M,,,0:127” Will read the step pos 22 & apply the Shift & mask signal conditioning shifting
0 bits & AND’ing with 127 (bits 0-7) which results in the +-63 step position
Example 2: “RTU1:STP:1:22|S&M,,,7:1” Will read the step pos 22 & apply the Shift & mask signal conditioning shifting 7
bits & AND’ing with 1 (bit 8) which results in the transient state
If a Digital Block in fix OR the extra :<bit> filed is used via OPC the QDS information may be accessed
QDS := CP8{OV,RES,BL,SB,NT,IV}
OV := BS1[1]<0..1>
<0> := no overflow
<1> := overflow
RES = RESERVE:= BS3[2..4]<0>
BL := BS1[5]<0..1>
<0> := not blocked
<1> := blocked
SB := BS1[6]<0..1>
<0> := not substituted
<1> := substituted
NT := BS1[7]<0..1>
<0> := topical
<1> := not topical
IV := BS1[8]<0..1>
<0> := valid
<1> := invalid
Example:
RTU1:STP:1:22:7 is the IV-invalid bit
Regulating Step commands

Regulating Step commands use the same addresses as the Step positions
RCO := CP8{RCS,QOC}
Page 15 of 7
RCS=Regulating step
command state := UI2[1..2]<0..3>
<0> := not permitted
<1> := next step LOWER
<2> := next step HIGHER
<3> := not permitted
QOC := CP6[3..8]{QU,S/E} see below QOC
QOC := CP6{QU, S/E}
QU := UI5[3..7]<0..31>
<0> := no additional definition *
<1> := short pulse duration (circuit-breaker), duration determined by a system parameter in the outstation
<2> := long duration pulse, duration determined by a system parameter in the outstation
<3> := persistent output
<4..8> := reserved for standard definitions of this companion standard (compatible range)
<9..15> := reserved for the selection of other predefined functions **
<16..31>:= reserved for special use (private range)
S/E := BS1[8]<0..1>
<0> := Execute
<1> := Select
Example 1 Address “RTU1:STP:1:22” is an analog value
Writing a value of 1 means STEP UP

Writing a value of 2 means STEP DOWN
Page 16 of 7
“I87” IO Driver 870-5-101 Compliance Spec
Extracted from 870-5-101 © IEC:1995, page 171
8 Interoperability
This document serves to specify which options and features of the IEC 870-5-101 standard
protocol are supported by the ProScada “I87” IO driver for OPC Clients.
Note that all supported and edited notes in red were added by the developers of the I87 driver.
8.1 Network configuration (network-specific parameters)

Note : The I87 driver supports Master Mode when it communicates with slave devices. The driver
can also be set to Slave mode, in this case the driver passively waits to be polled by the device on
the other end. The data sent to the master is the current data written from the SCADA database.
In addition The I87 driver supports a “Listen” Mode. The Listen mode allows a SCADA node to
Read & Log data being polled by another Master, This mode may also be used for Dual redundant
masters.
 Point-to-point  Multipoint-party line

 Multiple point-to-point  Multipoint-star
8.2 Physical layer

(network-specific parameter)
Transmission speed (control direction)

Unbalanced interchange Unbalanced interchange Balanced interchange
circuit V.24/V.28 circuit V.24/V.28 circuit X.24/X.27
Standard Recommended if >1 200 bit/s
 100 bit/s  2400 bit/s  2400 bit/s  56000 bit/s
 300 bit/s  9600 bit/s  9600 bit/s
 600 bit/s  19200 bit/s  19200 bit/s
 1200 bit/s  38400 bit/s  38400 bit/s
Transmission speed (monitor direction)

Unbalanced interchange Unbalanced interchange Balanced interchange
circuit V.24/V.28 circuit V.24/V.28 circuit X.24/X.27
Standard Recommended if >1 200 bit/s
 300 bit/s  9600 bit/s  9600 bit/s
 600 bit/s  19200 bit/s  19200 bit/s
 1200 bit/s  38400 bit/s  38400 bit/s
Note : The I87 driver does allow RTS/CTS with RTS toggling, which may be used with 2
wire RS485 line drivers where the RTS line is used to energise the transmitter. The same
Page 17 of 7

SPI & DPI Commands Slave Mode Notes: MV Setpoints

Uploaded by

Copyright:

Available Formats

SPI & DPI Commands Slave Mode Notes: MV Setpoints

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SPI & DPI Commands Slave Mode Notes: MV Setpoints

Uploaded by

Copyright:

Available Formats

Copyright www.proscada.

SPI & DPI commands Slave mode notes

MV Setpoints Slave mode notes

Actions that occur during setpoint write:

Format of Integrated totals (Counters)

To read the IT Sequence number use the address “<rtu>:IT:<asdu>:<obj>|ITSQ

Sending Counter interrogations is performed by writing to addesses <rtu>:IT:<asdu>:<obj> the

Format of Step Position Information

<0> := equipment is not in transient state

RTU1:STP:1:22:7 is the IV-invalid bit

Regulating Step commands

Example 1 Address “RTU1:STP:1:22” is an analog value

Writing a value of 1 means STEP UP

Extracted from 870-5-101 © IEC:1995, page 171

8.1 Network configuration (network-specific parameters)

 Point-to-point  Multipoint-party line

8.2 Physical layer

Transmission speed (control direction)

Transmission speed (monitor direction)

You might also like