BS en Iso 15609-3-2004
BS en Iso 15609-3-2004
BS en Iso 15609-3-2004
15609-3:2004
Specification and
qualification of welding
procedures for metallic
materials —
Welding procedure
specification —
Part 3: Electron beam welding
ICS 25.160.10
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS EN ISO 15609-3:2004
National foreword
English version
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Descriptif d'un mode metallische Werkstoffe - Schweißanweisung - Teil 3:
opératoire de soudage - Partie 3: Soudage par faisceau Elektronenstrahlschweißen (ISO 15609-3:2004)
d'électrons (ISO 15609-3:2004)
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15609-3:2004: E
worldwide for CEN national Members.
EN ISO 15609-3:2004 (E)
Contents page
Foreword......................................................................................................................................................................3
1 Scope ..............................................................................................................................................................4
2 Normative references ....................................................................................................................................4
3 Terms and definitions ...................................................................................................................................4
4 Technical content of welding procedure specification (WPS) ..................................................................6
4.1 General............................................................................................................................................................6
4.2 Welding process ............................................................................................................................................6
4.3 Related to the manufacturer .........................................................................................................................6
4.4 Equipment used .............................................................................................................................................6
4.5 Related to the parent materials ....................................................................................................................6
4.6 Filler or other additional material(s) ............................................................................................................7
4.7 Joint design....................................................................................................................................................7
4.8 Joint preparation............................................................................................................................................7
4.9 Jigs, fixtures and tooling ..............................................................................................................................7
4.10 Welding position ............................................................................................................................................7
4.11 Back and/or front support.............................................................................................................................7
4.12 Magnetism ......................................................................................................................................................7
4.13 Welding technique .........................................................................................................................................7
4.14 Welding parameters ......................................................................................................................................7
4.15 Pre and post weld heating ............................................................................................................................8
4.16 Operations after welding...............................................................................................................................8
Annex A (informative) Example of a Welding Procedure Specification for electron beam welding
(process 51)....................................................................................................................................................9
2
prEN ISO 15609-3:2004 (E)
Foreword
This document (EN ISO 15609-3:2004) has been prepared by Technical Committee CEN /TC 121, "Welding", the
secretariat of which is held by DIN, in collaboration with ISO/TC 44 "Welding and allied processes".
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest
by February 2005.
Annex A is informative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
3
EN ISO 15609-3:2004 (E)
1 Scope
This standard specifies requirements for the content of welding procedure specifications for electron beam welding.
This standard is part of a series of standards, details of this series are given in EN ISO 15607:2003, annex A.
Variables listed in this standard are those influencing the quality and properties of the welded joint.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
(ISO 4063:1998).
EN ISO 6947, Welds — Working positions — Definitions of angles of slope and rotation (ISO 6947:1993).
EN ISO 15607:2003, Specification and qualification of welding procedures for metallic materials — General rules
(ISO 15607:2003).
3.1
slope up
controlled increase of the beam power at the beginning of welding
3.2
slope down
controlled decrease of the beam power at the end of welding. The slope down region is the region on the workpiece
in which the effects of slope down occur. It can consist of one or two areas, depending on the selected welding
mode:
4
EN ISO 15609-3:2004 (E)
3.3
working distance
distance between the surface of the workpiece and a standard reference point of the equipment which is traceable
to the true focusing lens centre
3.4
tacking pass
pass made to hold the parts to be welded in proper alignment until the final welds are made
NOTE This may be produced by a continuous or discontinuous pass with partial penetration.
3.5
welding pass
pass ensuring fusion to the required depth
3.6
cosmetic pass
pass for superficial remelting of the weld in order to enhance its appearance
3.7
overlap
portion of the welding pass remelted prior to the slope down
3.8
back or front support
plate placed against the workpiece on either the back or front face of the joint in order to retain the molten weld
metal
3.9
beam current
value of the electric current in the beam
3.10
beam current pulsing
intentional periodic variation of the beam current
3.11
focusing lens current
current passing through the focusing lens coil
3.12
beam deflection
electromagnetic deflection of the beam from the gun axis
3.13
beam oscillation
an intentional periodic deflection of the beam, achieved by electromagnetic forces
the frequency;
5
EN ISO 15609-3:2004 (E)
4.1 General
The welding procedure specification (WPS) shall provide all information required to make a weld.
Welding procedure specifications may cover a certain range of thicknesses of the joined parts and may also cover
a range of parent metals and even filler metals. Some manufacturers may additionally prefer to prepare work
instructions for each specific job as part of the detailed production planning.
Information listed below is adequate for most welding operations. For some applications it may be necessary to
supplement or reduce the list. The relevant information shall be specified in the WPS.
Ranges and tolerances, according to the manufacturer's experience, shall be specified when appropriate.
reference to the welding procedure qualification record (WPQR) or other documents, as required.
cathode type.
Filler material(s) feeding system (if any): a description (schematic) showing design, position of the filler
material(s) feeding system in relation to joint, welding direction and welding point shall be provided.
Designation of the material(s) and any backing plates or supports used and any reference standard(s);
6
EN ISO 15609-3:2004 (E)
the designation and reference standard for any filler material(s) or other additional material(s) used in the joint;
the dimensions of any filler material(s) or other additional material(s) used in the joint;
any special handling instructions for any filler material(s) or other additional material(s) used in the joint.
A sketch showing the joint design/configuration, dimensions and tolerances, including surface finish, or reference to
another standard which provides this information.
for magnetic materials any recommendation will be specified on the WPS, if necessary;
The methods to be used for workpiece fixturing (including manual tack welding, if used).
4.12 Magnetism
If necessary, the components should be demagnetised using a qualified procedure with a reference number.
The welding technique sketch showing details of all welding passes (tacking pass, welding pass, cosmetic pass).
focusing lens current(s) in amperes (A), current control device setting(s) (arbitrary units) or focus position with
respect to workpiece surface;
beam deflection:
2) alternating current (AC) oscillation: shape, and orientation with respect to the welding direction, frequency
in hertz (Hz), dimensions (mm of deflection);
7
EN ISO 15609-3:2004 (E)
overlap, slope up, slope down [in seconds (s), millimetres (mm) or degrees (deg)];
slope profile.
Travel direction;
If preheating and/or post heating and/or post weld heat treatment are required, the temperature and time at
temperature shall be included on the WPS complete with any other instructions related to the heat treatment. If the
electron beam is to be used for pre or post heating, the relevant parameters shall be recorded on the WPS.
8
EN ISO 15609-3:2004 (E)
Annex A
(informative)
WPS identification:
Manufacturer:
WPQR N°:
9
EN ISO 15609-3:2004 (E)
Preparation:
Procedure
Tacking pass Welding pass Cosmetic pass
Welding position
Welding technique
Accelerating voltage (kV)
Beam current (mA)
— continuous
— pulse:
- frequency:
- amplitude:
- other:
Focusing lens current(s)(A) or
Focus setting
Beam deflection
— DC deflection
— AC oscillation
— shape
— frequency (Hz)
— dimensions :
-longitudinal
- transverse
Overlap (s, mm or deg)
Slope up (s, mm or deg)
Slope down (s, mm or deg)
Slope profile
Travel direction
Surface travel speed (mm/min or mm/s)
Travel speed ramping a
a
Wire/filler feed rate
Working distance (mm)
Gun pressure (mbar or Pa)
Chamber pressure (mbar or Pa)
Additional equipment
— Preheatinga
— Postheatinga
a
Operations after welding
Additional information
a If required
.......................................................................
Manufacturer
(name, signature, date)
10
blank
BS EN ISO
15609-3:2004
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-global.com. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info@bsi-global.com.
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: membership@bsi-global.com.
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-global.com.
W4 4AL