3M™ Stainless Steel Cleaner & Polish

Safety Data Sheet

Copyright,2018,3M Canada Company
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document group: 10-2819-0 Version number: 16.00

Issue Date: 2018/09/25 Supercedes Date: 2018/04/18

This Safety Data Sheet has been prepared in accordance with the Canadian Hazardous Products Regulations.

SECTION 1: Identification
1.1. Product identifier
3M™ Stainless Steel Cleaner & Polish

Product Identification Numbers

UU-0092-2904-6 XN-1015-5591-2 XN-1015-7536-5

1.2. Recommended use and restrictions on use

Intended Use
Metal Polish

Specific Use
Cleans and polishes stainless steel, chrome, aluminum and laminated plastic surfaces.

Restrictions on use
Not applicable

1.3. Supplier’s details

Company: 3M Canada Company

Division: Commercial Solutions Division
Address: 1840 Oxford Street East, Post Office Box 5757, London, Ontario N6A 4T1
Telephone: (800) 364-3577
Website: www.3M.ca

1.4. Emergency telephone number

Medical Emergency Telephone: (519) 451-2500, Ext. 2222; Transportation Emergency Telephone (CANUTEC): (613) 996-
6666

SECTION 2: Hazard identification

2.1. Classification of the substance or mixture
Flammable Aerosol: Category 1.
Gas Under Pressure: Liquefied gas.
Specific Target Organ Toxicity (single exposure): Category 1.

2.2. Label elements

__________________________________________________________________________________________

Page: 1 of 10
3M™ Stainless Steel Cleaner & Polish

Signal word
Danger

Symbols
Flame | Gas cylinder | Health Hazard |

Pictograms

Hazard statements
Extremely flammable aerosol. Contains gas under pressure; may explode if heated.

Causes damage to organs: cardiovascular system |

Precautionary statements
General:
Keep out of reach of children. Read label before use. If medical advice is needed, have product container or label at hand.

Prevention:
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not spray on an open
flame or other ignition source. Do not pierce or burn, even after use. Do not breathe dust/fume/gas/mist/vapours/spray. Do not
eat, drink or smoke when using this product. Wash exposed skin thoroughly after handling.

Response:
IF exposed or concerned: Call a POISON CENTRE or doctor/physician.

Storage:
Protect from sunlight. Do not expose to temperatures exceeding 50C/122F. Store in a well-ventilated place. Store locked up.

Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.

Notes to Physician:
Exposure may increase myocardial irritability. Do not administer sympathomimetic drugs unless absolutely necessary.

2.3. Other hazards

None known.

11% of the mixture consists of ingredients of unknown acute dermal toxicity.

35% of the mixture consists of ingredients of unknown acute inhalation toxicity.

SECTION 3: Composition/information on ingredients

This material is a mixture.

Ingredient C.A.S. No. % by Wt Common Name

Water 7732-18-5 40 - 70 Water
White Mineral Oil (Petroleum) 8042-47-5 10 - 30 White mineral oil, petroleumnation of
hydrocarbons obtained from the intensive
treatment of a petroleum fraction with
sulfuric acid and oleum, or by

__________________________________________________________________________________________

Page: 2 of 10
3M™ Stainless Steel Cleaner & Polish

hydrogenation, or by a combination of
hydrogenation and acid treatment.
Additional washing and treating st
Isobutane 75-28-5 7 - 13 Trade Secret * Propane, 2-methyl-
Sorbitan Oleate 1338-43-8 0.5 - 1.5 Sorbitan, mono-9-octadecenoate, (Z)-
Ethanolamine 141-43-5 0.1 - 1 Ethanol, 2-amino-

*The actual concentration of this ingredient has been withheld as a trade secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:
Remove person to fresh air. Get medical attention.

Skin Contact:
Wash with soap and water. If you feel unwell, get medical attention.

Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:
Rinse mouth. If you feel unwell, get medical attention.

4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required
Exposure may increase myocardial irritability. Do not administer sympathomimetic drugs unless absolutely necessary.

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media
Use a fire fighting agent suitable for the surrounding fire.

5.2. Special hazards arising from the substance or mixture

Closed containers exposed to heat from fire may build pressure and explode.

Hazardous Decomposition or By-Products

Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion

5.3. Special protective actions for fire-fighters

Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools.
Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or
exhaust vapours, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and

__________________________________________________________________________________________

Page: 3 of 10
3M™ Stainless Steel Cleaner & Polish

could cause flammable gases or vapours in the spill area to burn or explode. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

If possible, seal leaking container. Place leaking containers in a well-ventilated area, preferably an operating exhaust hood, or
if necessary outdoors on an impermeable surface until appropriate packaging for the leaking container or its contents is
available. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available
inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material
does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible using non-
sparking tools. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with
water. Seal the container. Dispose of collected material as soon as possible in accordance with applicable
local/regional/national/international regulations.

SECTION 7: Handling and storage

7.1. Precautions for safe handling
Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an
open flame or other ignition source. Do not pierce or burn, even after use. Do not breathe
dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this
product. Wash thoroughly after handling. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.)

7.2. Conditions for safe storage including any incompatibilities

Store in a well-ventilated place. Protect from sunlight. Do not expose to temperatures exceeding 50C/122F. Protect from
sunlight. Store in a well-ventilated place. Store away from heat. Store away from acids. Store away from oxidizing
agents.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient C.A.S. No. Agency Limit type Additional Comments
Ethanolamine 141-43-5 ACGIH TWA:3 ppm;STEL:6 ppm
Isobutane 75-28-5 ACGIH STEL:1000 ppm
Natural gas 75-28-5 ACGIH Limit value not established: simple asphyxiant
MINERAL OILS, HIGHLY- 8042-47-5 ACGIH TWA(inhalable fraction):5
REFINED OILS mg/m3
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

__________________________________________________________________________________________

Page: 4 of 10
3M™ Stainless Steel Cleaner & Polish

Eye/face protection

Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Full Face Shield
Indirect Vented Goggles

Skin/hand protection
No chemical protective gloves are required.

Respiratory protection

An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part
of a full respiratory protection program. Based on the results of the exposure assessment, select from the following
respirator type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapours and particulates
Half facepiece or full facepiece supplied-air respirator
Organic vapor respirators may have short service life.

For questions about suitability for a specific application, consult with your respirator manufacturer.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state Liquid
Specific Physical Form: Aerosol
Appearance/Odour Thick white emulsion citrus odour
Odour threshold No Data Available
pH 9 - 11
Melting point/Freezing point Not Applicable
Boiling point > 100 ºC
Flash Point No Data Available
Flash Point No flash point
Evaporation rate No Data Available
Flammability (solid, gas) Not Applicable
Flammable Limits(LEL) No Data Available
Flammable Limits(UEL) No Data Available
Vapour Density No Data Available
Density 0.95 g/ml
Relative density 0.92 - 0.98 [Ref Std:WATER=1]
Water solubility Complete
Solubility- non-water No Data Available
Partition coefficient: n-octanol/ water No Data Available
Autoignition temperature No Data Available
Decomposition temperature No Data Available
Viscosity 1,400 - 4,500 mPa-s [Details:For Liquid]
Molecular weight No Data Available
Volatile Organic Compounds 10 - 12 % weight [Test Method:calculated per CARB title 2]
Percent volatile 75 - 80 % weight
VOC Less H2O & Exempt Solvents 265 - 295 g/l [Test Method:calculated per CARB title 2]

SECTION 10: Stability and reactivity

__________________________________________________________________________________________

Page: 5 of 10
3M™ Stainless Steel Cleaner & Polish

10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.

10.2. Chemical stability

Stable.

10.3. Possibility of hazardous reactions

Hazardous polymerization will not occur.

10.4. Conditions to avoid

Heat
Sparks and/or flames

10.5. Incompatible materials

Strong oxidizing agents
Strong acids

10.6. Hazardous decomposition products

Substance Condition
None known.

Refer to section 5.2 for hazardous decomposition products during combustion.

SECTION 11: Toxicological information

The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.

11.1. Information on Toxicological effects

Signs and Symptoms of Exposure

Based on test data and/or information on the components, this material may produce the following health effects:

Inhalation:
May cause additional health effects (see below).

Skin Contact:
Contact with the skin during product use is not expected to result in significant irritation.

Eye Contact:
Contact with the eyes during product use is not expected to result in significant irritation.

Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.

Additional Health Effects:

Single exposure may cause target organ effects:

Cardiac Sensitization: Signs/symptoms may include irregular heartbeat (arrhythmia), faintness, chest pain, and may be fatal.

__________________________________________________________________________________________

Page: 6 of 10
3M™ Stainless Steel Cleaner & Polish

Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.

Acute Toxicity
Name Route Species Value
Overall product Dermal No data available; calculated ATE >5,000 mg/kg
Overall product Inhalation- No data available; calculated ATE >12.5 mg/l
Dust/Mist(4
hr)
Overall product Ingestion No data available; calculated ATE >5,000 mg/kg
White Mineral Oil (Petroleum) Dermal Rabbit LD50 > 2,000 mg/kg
White Mineral Oil (Petroleum) Ingestion Rat LD50 > 5,000 mg/kg
Isobutane Inhalation- Rat LC50 276,000 ppm
Gas (4
hours)
Sorbitan Oleate Dermal LD50 estimated to be > 5,000 mg/kg
Sorbitan Oleate Ingestion Rat LD50 > 39,800 mg/kg
Ethanolamine Inhalation- official LC50 estimated to be 10 - 20 mg/l
Vapor classifica
tion
Ethanolamine Dermal Rabbit LD50 1,000 mg/kg
Ethanolamine Ingestion Rat LD50 1,720 mg/kg
ATE = acute toxicity estimate

Skin Corrosion/Irritation
Name Species Value

White Mineral Oil (Petroleum) Rabbit No significant irritation

Isobutane Professio No significant irritation
nal
judgeme
nt
Ethanolamine Rabbit Corrosive

Serious Eye Damage/Irritation

Name Species Value

White Mineral Oil (Petroleum) Rabbit Mild irritant

Isobutane Professio No significant irritation
nal
judgeme
nt
Ethanolamine Rabbit Corrosive

Skin Sensitization
Name Species Value
White Mineral Oil (Petroleum) Guinea Not classified
pig
Ethanolamine Guinea Not classified
pig

Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.

Germ Cell Mutagenicity

Name Route Value

White Mineral Oil (Petroleum) In Vitro Not mutagenic

Isobutane In Vitro Not mutagenic

__________________________________________________________________________________________

Page: 7 of 10
3M™ Stainless Steel Cleaner & Polish

Ethanolamine In Vitro Not mutagenic

Ethanolamine In vivo Not mutagenic

Carcinogenicity
Name Route Species Value
White Mineral Oil (Petroleum) Dermal Mouse Not carcinogenic
White Mineral Oil (Petroleum) Inhalation Multiple Not carcinogenic
animal
species

Reproductive Toxicity

Reproductive and/or Developmental Effects

Name Route Value Species Test result Exposure
Duration
White Mineral Oil (Petroleum) Ingestion Not classified for female reproduction Rat NOAEL 4,350 13 weeks
mg/kg/day
White Mineral Oil (Petroleum) Ingestion Not classified for male reproduction Rat NOAEL 4,350 13 weeks
mg/kg/day
White Mineral Oil (Petroleum) Ingestion Not classified for development Rat NOAEL 4,350 during
mg/kg/day gestation
Ethanolamine Dermal Not classified for development Rat NOAEL 225 during
mg/kg/day organogenesi
s
Ethanolamine Ingestion Not classified for development Rat NOAEL 616 during
mg/kg/day organogenesi
s

Target Organ(s)

Specific Target Organ Toxicity - single exposure

Name Route Target Organ(s) Value Species Test result Exposure
Duration
Isobutane Inhalation cardiac sensitization Causes damage to organs Multiple NOAEL Not
animal available
species
Isobutane Inhalation central nervous May cause drowsiness or Human NOAEL Not
system depression dizziness and available
animal
Isobutane Inhalation respiratory irritation Not classified Mouse NOAEL Not
available
Ethanolamine Inhalation respiratory irritation May cause respiratory irritation Human NOAEL Not
and available
animal

Specific Target Organ Toxicity - repeated exposure

Name Route Target Organ(s) Value Species Test result Exposure
Duration
White Mineral Oil Ingestion hematopoietic Not classified Rat NOAEL 90 days
(Petroleum) system 1,381
mg/kg/day
White Mineral Oil Ingestion liver | immune Not classified Rat NOAEL 90 days
(Petroleum) system 1,336
mg/kg/day
Isobutane Inhalation kidney and/or Not classified Rat NOAEL 13 weeks
bladder 4,500 ppm
Ethanolamine Inhalation liver | kidney and/or Not classified Multiple NOAEL 5 weeks
bladder | respiratory animal 0.656 mg/l
system species
Ethanolamine Ingestion hematopoietic Not classified Rat NOAEL Not
system | liver | available
kidney and/or
bladder | respiratory
system

__________________________________________________________________________________________

Page: 8 of 10
3M™ Stainless Steel Cleaner & Polish

Aspiration Hazard
Name Value
White Mineral Oil (Petroleum) Aspiration hazard

Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.

SECTION 12: Ecological information

No data available.

SECTION 13: Disposal considerations

Dispose of contents/ container in accordance with the local/regional/national/international regulations.

SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture

Global inventory status

Contact 3M for more information. The components of this material are in compliance with the provisions of the Korea
Chemical Control Act. Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Australia National Industrial Chemical Notification and
Assessment Scheme (NICNAS). Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Japan Chemical Substance Control Law. Certain
restrictions may apply. Contact the selling division for additional information. The components of this material are in
compliance with the provisions of Philippines RA 6969 requirements. Certain restrictions may apply. Contact the selling
division for additional information. The components of this product are in compliance with the new substance notification
requirements of CEPA. The components of this product are in compliance with the chemical notification requirements of
TSCA. This product complies with Measures on Environmental Management of New Chemical Substances. All ingredients
are listed on or exempt from on China IECSC inventory.

SECTION 16: Other information

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to
address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or
similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material
but also include the toxic properties of combustion or decomposition products that are known to be generated in
significant quantities.
Health: 2 Flammability: 4 Instability: 0 Special Hazards: None
Aerosol Storage Code: 1

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

__________________________________________________________________________________________

Page: 9 of 10
3M™ Stainless Steel Cleaner & Polish

HMIS Hazard Classification

Health: 4 Flammability: 4 Physical Hazard: 0 Personal Protection: X - See PPE section.

Hazardous Material Identification System (HMIS® IV) hazard ratings are designed to inform employees of chemical hazards
in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use
and are not intended for use in emergency situations. HMIS® IV ratings are to be used with a fully implemented HMIS® IV
program. HMIS® is a registered mark of the American Coatings Association (ACA).

Document group: 10-2819-0 Version number: 16.00

Issue Date: 2018/09/25 Supercedes Date: 2018/04/18

The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF PERFORMANCE,
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M product
is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect
the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential
that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of
use or application.

3M Canada SDSs are available at www.3M.ca

__________________________________________________________________________________________

Page: 10 of 10