Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Safety Data Sheet: 3M™ Easy Clean Coating ECC-1000

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

3M™ Easy Clean Coating ECC-1000 07/25/18

Safety Data Sheet


Copyright,2018,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group: 16-1615-0 Version Number: 12.03


Issue Date: 07/25/18 Supercedes Date: 03/08/18

SECTION 1: Identification
1.1. Product identifier
3M™ Easy Clean Coating ECC-1000

Product Identification Numbers


98-0212-3001-0, 98-0212-3002-8, ZF-0002-1532-5, ZF-0002-1533-3

1.2. Recommended use and restrictions on use

Recommended use
HARD SURFACE COATING

1.3. Supplier’s details


MANUFACTURER: 3M
DIVISION: Advanced Materials Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA
Telephone: 1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number


1-800-364-3577 or (651) 737-6501 (24 hours)

SECTION 2: Hazard identification


2.1. Hazard classification
Reproductive Toxicity: Category 2.

2.2. Label elements


Signal word
Warning

Symbols
Health Hazard |

Pictograms

__________________________________________________________________________________________

Page 1 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

Hazard Statements
Suspected of damaging fertility or the unborn child.

Precautionary Statements

Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wear protective gloves.

Response:
IF exposed or concerned: Get medical advice/attention.

Storage:
Store locked up.

Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.

SECTION 3: Composition/information on ingredients


Ingredient C.A.S. No. % by Wt
Fluoropolymer (NJTS Reg. No. 04499600-6414P) Trade Secret* 99 - 100
Methyl Alcohol 67-56-1 <= 0.5

NJTS or NJTSRN: New Jersey Trade Secret Registry Number.

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.

SECTION 4: First aid measures


4.1. Description of first aid measures

Inhalation:
Remove person to fresh air. If you are concerned, get medical advice.

Skin Contact:
Wash with soap and water. If you are concerned, get medical advice.

Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:
Rinse mouth. If you are concerned, get medical advice.

4.2. Most important symptoms and effects, both acute and delayed
__________________________________________________________________________________________

Page 2 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required
Not applicable

SECTION 5: Fire-fighting measures


5.1. Suitable extinguishing media
Material will not burn. Non-combustible. Use a fire fighting agent suitable for surrounding fire.

5.2. Special hazards arising from the substance or mixture


Exposure to extreme heat can give rise to thermal decomposition.

Hazardous Decomposition or By-Products


Substance Condition
Carbonyl Fluoride During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Hydrogen Fluoride During Combustion
Ammonia During Combustion
Toxic Vapor, Gas, Particulate During Combustion

5.3. Special protective actions for fire-fighters


When fire fighting conditions are severe and total thermal decomposition of the product is possible, wear full protective
clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants,
bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.

SECTION 6: Accidental release measures


6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions


Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.

6.3. Methods and material for containment and cleaning up


Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriate
solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions
on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with
applicable local/regional/national/international regulations.

SECTION 7: Handling and storage


7.1. Precautions for safe handling
Do not breathe thermal decomposition products. For industrial or professional use only. Do not handle until all safety
precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin,
or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to
__________________________________________________________________________________________

Page 3 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) Use personal protective equipment
(gloves, respirators, etc.) as required.

7.2. Conditions for safe storage including any incompatibilities


Store in a well-ventilated place. Keep container tightly closed to prevent contamination with water or air. If contamination
is suspected, do not reseal container. Store away from heat. Store away from acids. Store away from strong bases.
Store away from oxidizing agents.

SECTION 8: Exposure controls/personal protection


8.1. Control parameters

Occupational exposure limits


If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient C.A.S. No. Agency Limit type Additional Comments
Methyl Alcohol 67-56-1 ACGIH TWA:200 ppm;STEL:250 ppm SKIN
Methyl Alcohol 67-56-1 OSHA TWA:260 mg/m3(200 ppm)
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls


Provide appropriate local exhaust when product is heated. For those situations where the material might be exposed to
extreme overheating due to misuse or equipment failure, use with appropriate local exhaust ventilation sufficient to maintain
levels of thermal decomposition products below their exposure guidelines. Use general dilution ventilation and/or local
exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control
dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection

Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Safety Glasses with side shields

Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Polymer laminate

Respiratory protection

An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part
of a full respiratory protection program. Based on the results of the exposure assessment, select from the following
respirator type(s) to reduce inhalation exposure:
__________________________________________________________________________________________

Page 4 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

During heating:
Use a positive pressure supplied-air respirator if there is a potential for over exposure from an uncontrolled release,
exposure levels are not known, or under any other circumstances where air-purifying respirators may not provide
adequate protection.

Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates

For questions about suitability for a specific application, consult with your respirator manufacturer.

SECTION 9: Physical and chemical properties


9.1. Information on basic physical and chemical properties
General Physical Form: Liquid
Specific Physical Form: Liquid
Odor, Color, Grade: Clear to slightly hazy, yellow to light brown with mild odor.
Odor threshold No Data Available
pH Not Applicable
Melting point Not Applicable
Boiling Point 305 - 307 ºC [@ 735 mmHg]
Flash Point No flash point
Evaporation rate No Data Available
Flammability (solid, gas) Not Applicable
Flammable Limits(LEL) Not Applicable
Flammable Limits(UEL) Not Applicable
Vapor Pressure <=25 torr [@ 20 ºC]
Vapor Density Approximately 1.1 Units not avail. or not appl. [Ref Std:AIR=1]
Density 1.7 g/ml
Specific Gravity 1.7 [Ref Std:WATER=1]
Solubility In Water 2 ppm
Solubility- non-water No Data Available
Partition coefficient: n-octanol/ water No Data Available
Autoignition temperature No Data Available
Decomposition temperature No Data Available
Viscosity 200 - 500 centipoise
Molecular weight No Data Available
Volatile Organic Compounds < 2 g/l [Test Method:South Cost Air Qual Mgmt Dist]
Percent volatile < 0.5 %
VOC Less H2O & Exempt Solvents Not Applicable

SECTION 10: Stability and reactivity


10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.

10.2. Chemical stability


Stable.

10.3. Possibility of hazardous reactions


Hazardous polymerization will not occur.

10.4. Conditions to avoid


Heat

__________________________________________________________________________________________

Page 5 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

10.5. Incompatible materials


Strong acids
Strong bases
Strong oxidizing agents
Amines
Reducing agents
Alcohols
Water
Reaction with water, alcohols, and amines is not hazardous if container can vent to the atmosphere to prevent pressure
buildup.

10.6. Hazardous decomposition products


Substance Condition
None known.

Refer to section 5.2 for hazardous decomposition products during combustion.

Extreme heat arising from situations such as misuse or equipment failure can generate hydrogen fluoride as a decomposition
product.

SECTION 11: Toxicological information


The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.

11.1. Information on Toxicological effects

Signs and Symptoms of Exposure

Based on test data and/or information on the components, this material may produce the following health effects:

Inhalation:
No known health effects.

Skin Contact:
Contact with the skin during product use is not expected to result in significant irritation.

Eye Contact:
Contact with the eyes during product use is not expected to result in significant irritation.

Ingestion:
No known health effects.

Additional Health Effects:

Reproductive/Developmental Toxicity:
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.

Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.

__________________________________________________________________________________________

Page 6 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

Acute Toxicity
Name Route Species Value
Overall product Ingestion No data available; calculated ATE >5,000 mg/kg
Fluoropolymer (NJTS Reg. No. 04499600-6414P) Ingestion Rat LD50 > 1,000 mg/kg
Methyl Alcohol Dermal LD50 estimated to be 1,000 - 2,000 mg/kg
Methyl Alcohol Inhalation- LC50 estimated to be 10 - 20 mg/l
Vapor
Methyl Alcohol Ingestion LD50 estimated to be 50 - 300 mg/kg
ATE = acute toxicity estimate

Skin Corrosion/Irritation
Name Species Value

Fluoropolymer (NJTS Reg. No. 04499600-6414P) Rabbit No significant irritation


Methyl Alcohol Rabbit Mild irritant

Serious Eye Damage/Irritation


Name Species Value

Fluoropolymer (NJTS Reg. No. 04499600-6414P) Rabbit Mild irritant


Methyl Alcohol Rabbit Moderate irritant

Skin Sensitization
Name Species Value
Methyl Alcohol Guinea Not classified
pig

Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.

Germ Cell Mutagenicity


Name Route Value

Fluoropolymer (NJTS Reg. No. 04499600-6414P) In Vitro Not mutagenic


Methyl Alcohol In Vitro Some positive data exist, but the data are not
sufficient for classification
Methyl Alcohol In vivo Some positive data exist, but the data are not
sufficient for classification

Carcinogenicity
Name Route Species Value
Methyl Alcohol Inhalation Multiple Not carcinogenic
animal
species

Reproductive Toxicity

Reproductive and/or Developmental Effects


Name Route Value Species Test Result Exposure
Duration
Methyl Alcohol Ingestion Not classified for male reproduction Rat NOAEL 1,600 21 days
mg/kg/day
Methyl Alcohol Ingestion Toxic to development Mouse LOAEL 4,000 during
mg/kg/day organogenesi
s
Methyl Alcohol Inhalation Toxic to development Mouse NOAEL 1.3 during
mg/l organogenesi
s

__________________________________________________________________________________________

Page 7 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

Target Organ(s)

Specific Target Organ Toxicity - single exposure


Name Route Target Organ(s) Value Species Test Result Exposure
Duration
Methyl Alcohol Inhalation blindness Causes damage to organs Human NOAEL Not occupational
available exposure
Methyl Alcohol Inhalation central nervous May cause drowsiness or Human NOAEL Not not available
system depression dizziness available
Methyl Alcohol Inhalation respiratory irritation Some positive data exist, but the Rat NOAEL Not 6 hours
data are not sufficient for available
classification
Methyl Alcohol Ingestion blindness Causes damage to organs Human NOAEL Not poisoning
available and/or abuse
Methyl Alcohol Ingestion central nervous May cause drowsiness or Human NOAEL Not poisoning
system depression dizziness available and/or abuse

Specific Target Organ Toxicity - repeated exposure


Name Route Target Organ(s) Value Species Test Result Exposure
Duration
Methyl Alcohol Inhalation liver Not classified Rat NOAEL 6.55 4 weeks
mg/l
Methyl Alcohol Inhalation respiratory system Not classified Rat NOAEL 13.1 6 weeks
mg/l
Methyl Alcohol Ingestion liver | nervous Not classified Rat NOAEL 90 days
system 2,500
mg/kg/day

Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.

Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.

SECTION 12: Ecological information


Ecotoxicological information
Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.

SECTION 13: Disposal considerations


13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.

Dispose of waste product in a permitted industrial waste facility. Combustion products will include halogen acid
(HCl/HF/HBr). Facility must be capable of handling halogenated materials. Empty drums/barrels/containers used for
transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per
applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by
applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and
disposal facilities.

EPA Hazardous Waste Number (RCRA): Not regulated

__________________________________________________________________________________________

Page 8 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.

SECTION 15: Regulatory information


15.1. US Federal Regulations
Contact 3M for more information.

EPCRA 311/312 Hazard Classifications:


Physical Hazards
Not applicable

Health Hazards
Reproductive toxicity

15.2. State Regulations


Contact 3M for more information.

15.3. Chemical Inventories


The components of this material are in compliance with the China "Measures on Environmental Management of New
Chemical Substance". Certain restrictions may apply. Contact the selling division for additional information.

The components of this product are in compliance with the chemical notification requirements of TSCA. All required
components of this product are listed on the active portion of the TSCA Inventory.

Contact 3M for more information.

15.4. International Regulations


Contact 3M for more information.

This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

SECTION 16: Other information


NFPA Hazard Classification
Health: 3 Flammability: 0 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

HMIS Hazard Classification


Health: *0 Flammability: 0 Physical Hazard: 1 Personal Protection: X - See PPE section.

Hazardous Material Identification System (HMIS® IV) hazard ratings are designed to inform employees of chemical hazards
in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use
and are not intended for use in emergency situations. HMIS® IV ratings are to be used with a fully implemented HMIS® IV
program. HMIS® is a registered mark of the American Coatings Association (ACA).

__________________________________________________________________________________________

Page 9 of 10
3M™ Easy Clean Coating ECC-1000 07/25/18

Document Group: 16-1615-0 Version Number: 12.03


Issue Date: 07/25/18 Supercedes Date: 03/08/18

DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for
user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of
which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine
whether it is fit for a particular purpose and suitable for user's method of use or application.

3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic
transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its
completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the
SDS available directly from3M

3M USA SDSs are available at www.3M.com

__________________________________________________________________________________________

Page 10 of 10

You might also like