Parameter Manual

FANUC AC SERVO MOTOR @* series
FANUC AC SERVO MOTOR #* series
FANUC LINEAR MOTOR L*S series

FANUC SY NCHRONOUS
BUILT-IN SERVO MOTOR D*S series
PARAMETER MANUAL
B-65270EN/07
• No part of this manual may be reproduced in any form.
• All specifications and designs are subject to change without notice.
The products in this manual are controlled based on Japan’s “Foreign Exchange and
Foreign Trade Law”. The export from Japan may be subject to an export license by the
government of Japan.
Further, re-export to another country may be subject to the license of the government of
the country from where the product is re-exported. Furthermore, the product may also be
controlled by re-export regulations of the United States government.
Should you wish to export or re-export these products, please contact FANUC for advice.
In this manual we have tried as much as possible to describe all the various matters.
However, we cannot describe all the matters which must not be done, or which cannot be
done, because there are so many possibilities.
Therefore, matters which are not especially described as possible in this manual should be
regarded as ”impossible”.
This manual contains the program names or device names of other companies, some of
which are registered trademarks of respective owners. However, these names are not
followed by  or  in the main body.
■General Safety Precautions

• When an abnormality such as an alarm or a hardware failure occurs, the operations
described in the specifications are not guaranteed unless otherwise specifically noted.
When action corresponding to the abnormality is specifically described, take the action.
When no action is described, please contact FANUC.
• The signals and functions described in the specifications cannot be used separately for
safety functions unless otherwise described as being usable for the safety functions.
Their specifications are not assumed to be used as the safety functions in this case, an
unexpected danger may be caused. For information about the safety functions, please
contact FANUC.
Generally, the safety functions represent functions that protect the operators from
machine danger.
• A wrong device connection or setting can lead to unpredictable operation. When starting
to operate the machine for the first time after assembling the machine, replacing
components, or modifying parameter settings, exercise the greater care by, for
example, reducing the torque limit value, error detection level, or operating speed or by
operating the machine in such a way that an emergency stop can be made quickly.
B-65270EN/07 DEFINITION OF WARNING, CAUTION, AND NOTE
DEFINITION OF WARNING, CAUTION, AND NOTE

This manual includes safety precautions for protecting the user and
preventing damage to the machine. Precautions are classified into
Warning and Caution according to their bearing on safety. Also,
supplementary information is described as a Note. Read the Warning,
Caution, and Note thoroughly before attempting to use the machine.
WARNING
Applied when there is a danger of the user being
injured or when there is a damage of both the user
being injured and the equipment being damaged if
the approved procedure is not observed.
CAUTION
Applied when there is a danger of the equipment
being damaged, if the approved procedure is not
observed.
NOTE
The Note is used to indicate supplementary
information other than Warning and Caution.
- Read this manual carefully, and store it in a safe place.
s-1
B-65270EN/07 TABLE OF CONTENTS
TABLE OF CONTENTS
DEFINITION OF WARNING, CAUTION, AND NOTE .................................s-1
1 OVERVIEW ............................................................................................. 1
1.1 SERVO SOFTWARE AND SERVO CARDS SUPPORTED BY EACH NC
MODEL.......................................................................................................... 2
1.2 ABBREVIATIONS OF THE NC MODELS COVERED BY THIS MANUAL .... 5
1.3 RELATED MANUALS.................................................................................... 6
2 SETTING αiS/αiF/βiS SERIES SERVO PARAMETERS....................... 8

2.1 INITIALIZING SERVO PARAMETERS.......................................................... 9
2.1.1 Before Servo Parameter Initialization ......................................................................9
2.1.2 Parameter Initialization Flow .................................................................................10
2.1.3 Servo Parameter Initialization Procedure ...............................................................11
2.1.4 Setting Servo Parameters when a Separate Detector for the Serial Interface is
Used........................................................................................................................33
2.1.5 Setting Servo Parameters when an Analog Input Separate Detector Interface
Unit is Used ............................................................................................................44
2.1.6 Setting Parameters when an αiCZ Sensor is Used .................................................46
2.1.7 Setting Parameters When an Acceleration Sensor or Temperature Detection
Circuit Is Used........................................................................................................52
2.1.8 Actions for Illegal Servo Parameter Setting Alarms ..............................................61
2.1.9 Notes on Using the Control Axis Detach Function ................................................77
3 αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT............................ 78

3.1 SERVO TUNING SCREEN AND DIAGNOSIS INFORMATION .................. 79
3.1.1 Servo Tuning Screen ..............................................................................................79
3.1.2 Diagnosis Information List.....................................................................................82
3.1.3 Actual Current Peak Hold Display .........................................................................85
3.1.4 Acceleration Monitor Function ..............................................................................86
3.2 ACTIONS FOR ALARMS ............................................................................ 87
3.3 ADJUSTING PARAMETERS FOR HIGH-SPEED AND HIGH-PRECISION
MACHINING ................................................................................................ 96
3.3.1 Servo HRV Control Adjustment Procedure ...........................................................96
3.3.2 High-speed Positioning Adjustment Procedure....................................................119
3.3.3 Rapid Traverse Positioning Adjustment Procedure..............................................122
3.3.4 Vibration in the Stop State ...................................................................................127
3.3.5 Vibration during Travel........................................................................................129
c-1
TABLE OF CONTENTS B-65270EN/07
3.3.6 Stick Slip ..............................................................................................................131

3.3.7 Overshoot .............................................................................................................132
4 SERVO FUNCTION DETAILS ............................................................ 133

4.1 SERVO HRV CONTROL ........................................................................... 134
4.1.1 Servo HRV2 Control ............................................................................................137
4.2 HIGH-SPEED HRV CURRENT CONTROL ............................................... 138
4.2.3 High-Speed HRV Current Control .......................................................................149
4.3 CUTTING/RAPID SWITCHING FUNCTION .............................................. 150
4.4 VIBRATION SUPPRESSION IN THE STOP STATE................................. 156
4.4.1 Velocity Loop High Cycle Management Function ..............................................156
4.4.2 Acceleration Feedback Function ..........................................................................158
4.4.3 Variable Proportional Gain Function in the Stop State ........................................160
4.4.4 N Pulses Suppression Function ............................................................................164
4.4.5 Current Loop 1/2 PI Control Function .................................................................166
4.5 MACHINE RESONANCE ELIMINATION FUNCTION ............................... 168
4.5.1 Selecting a Resonance Elimination Function .......................................................168
4.5.2 Torque Command Filter (Middle-Frequency Resonance Elimination Filter) ......169
4.5.3 Resonance Elimination Filter Function
(High-Frequency Resonance Elimination Filter) .................................................171
4.5.4 Disturbance Elimination Filter Function
(Low-Frequency Resonance Elimination Filter) ..................................................176
4.5.5 Resonance Elimination Filter L
(Low-Frequency Resonance Elimination Filter) ..................................................180
4.5.6 Observer Function ................................................................................................183
4.5.7 Vibration Damping Control Function ..................................................................187
4.5.8 Dual Position Feedback Function (Optional Function)........................................189
4.5.9 Machine Speed Feedback Function......................................................................196
4.5.10 Machining Point Control ......................................................................................199
4.6 CONTOUR ERROR SUPPRESSION FUNCTION .................................... 202
4.6.1 Feed-forward Function .........................................................................................202
4.6.2 Advanced Preview Feed-forward Function..........................................................206
4.6.3 RISC Feed-forward Function ...............................................................................209
4.6.4 Cutting/Rapid Feed-forward Switching Function ................................................211
4.6.5 Feed-forward Timing Adjustment Function.........................................................213
4.6.6 Backlash Acceleration Function...........................................................................216
c-2
4.6.7 Two-stage Backlash Acceleration Function .........................................................223

4.6.8 Static Friction Compensation Function ................................................................238
4.6.9 Torsion Preview Control Function .......................................................................241
4.7 OVERSHOOT COMPENSATION FUNCTION .......................................... 251
4.8 HIGH-SPEED POSITIONING FUNCTION ................................................ 257
4.8.1 Position Gain Switching Function........................................................................257
4.8.2 Low-speed Integral Function................................................................................261
4.8.3 Fine Acceleration/Deceleration (FAD) Function .................................................263
4.9 SERIAL FEEDBACK DUMMY FUNCTIONS ............................................. 272
4.9.1 Serial Feedback Dummy Functions......................................................................272
4.9.2 How to Use the Dummy Feedback Functions for a Multiaxis Servo Amplifiers
when an Axis is not in Use...................................................................................275
4.10 BRAKE CONTROL FUNCTION................................................................. 276
4.11 QUICK STOP FUNCTION ......................................................................... 280
4.11.1 Quick Stop Type 1 at Emergency Stop ................................................................280
4.11.2 Quick Stop Type 2 at Emergency Stop ................................................................282
4.11.3 Lifting Function Against Gravity at Emergency Stop..........................................283
4.11.3.1 Lifting function against gravity at emergency stop ......................................... 283
4.11.3.2 Function based on the DI signal for switching the distance to lift................... 287
4.11.3.3 Method of setting a distance to lift in µm........................................................ 290
4.11.4 Quick Stop Function for Hardware Disconnection of Separate Detector.............291
4.11.5 Quick Stop Function for Separate Serial Detector Alarms...................................293
4.11.6 Quick Stop Function at OVL and OVC Alarm ....................................................294
4.11.7 Overall Use of the Quick Stop Functions.............................................................295
4.12 UNEXPECTED DISTURBANCE TORQUE DETECTION
FUNCTIONDISTURBANCE TORQUE DETECTION................................. 296
4.12.1 Unexpected Disturbance Torque Detection Function ..........................................296
4.12.2 Cutting/Rapid Unexpected Disturbance Torque Detection Switching Function..307
4.12.3 Unexpected Disturbance Torque Detection Switching Function Depending on
Acc. ......................................................................................................................309
4.13 FUNCTION FOR OBTAINING CURRENT OFFSETS AT EMERGENCY
STOP......................................................................................................... 311
4.14 LINEAR MOTOR PARAMETER SETTING................................................ 312
4.14.1 Procedure for Setting the Initial Parameters of Linear Motors ............................312
4.14.2 Detection of an Overheat Alarm by Servo Software when a Linear Motor and
a Synchronous Built-in Servo Motor are Used.....................................................337
4.14.3 Smoothing Compensation for Linear Motor ........................................................341
c-3
4.15 SYNCHRONOUS BUILT-IN SERVO MOTOR PARAMETER SETTING ... 346

4.15.1 Procedure for Setting the Initial Parameters of Synchronous Built-in Servo
Motors ..................................................................................................................346
4.15.2 Detection of an Overheat Alarm by Servo Software when a Synchronous
Built-in Servo Motor are Used .............................................................................382
4.15.3 Smoothing Compensation for Synchronous Built-in Servo Motor ......................383
4.16 SETTING PARAMETERS FOR LARGE SERVO MOTORS...................... 388
4.16.1 Motor Models and System Configurations...........................................................388
4.16.2 Setting Parameters in the Torque Tandem Configuration ....................................389
4.16.3 Setting Parameters in the PWM Distribution Module Configuration ..................391
4.16.4 Data Measurement and Diagnosis with a PWM Distribution Module (PDM).....394
4.17 INTERACTIVE FORCE COMPENSATION FUNCTION ............................ 398
4.18 TORQUE CONTROL FUNCTION ............................................................. 415
4.19 TANDEM DISTURBANCE ELIMINATION CONTROL
(POSITION TANDEM) (Optional Function)................................................ 418
4.20 SYNCHRONOUS AXES AUTOMATIC COMPENSATION ........................ 426
4.21 TORQUE TANDEM CONTROL FUNCTION (Optional Function) .............. 430
4.21.1 Preload Function ..................................................................................................436
4.21.2 Damping Compensation Function........................................................................439
4.21.3 Velocity Feedback Average Function ..................................................................441
4.21.4 Servo Alarm 2-axis Simultaneous Monitor Function...........................................442
4.21.5 Motor Feedback Sharing Function .......................................................................444
4.21.6 Full-closed Feedback Sharing Function ...............................................................445
4.21.7 Adjustment ...........................................................................................................446
4.21.8 Cautions for Controlling One Axis with Two Motors..........................................450
4.21.9 Velocity loop integrator copy function ................................................................451
4.21.10 Tandem Speed Difference Alarm Function..........................................................452
4.21.11 Block Diagrams....................................................................................................454
4.22 SERVO TUNING TOOL SERVO GUIDE................................................... 455
4.22.1 SERVO GUIDE ...................................................................................................455
5 DETAILS OF PARAMETERS ............................................................. 473

5.1 DETAILS OF THE SERVO PARAMETERS FOR Series 30i, 31i, 32i, 15i,
16i, 18i, 21i, 0i, 20i, Power Mate i (SERIES 90D0, 90E0, 90B0, 90B1,
90B6, 90B5, AND 9096) ............................................................................ 474
c-4
6 PARAMETER LIST ............................................................................. 505

6.1 PARAMETERS FOR HRV1 CONTROL .................................................... 506
6.2 PARAMETERS FOR HRV2 CONTROL .................................................... 516
6.3 PARAMETERS FOR HRV1 CONTROL (FOR Series 0i-A) ....................... 531
APPENDIX
A ANALOG SERVO INTERFACE SETTING PROCEDURE.................. 537
B PARAMETERS SET WITH VALUES IN DETECTION UNITS ............ 544
B.1 PARAMETERS FOR Series 15i ................................................................ 545
B.2 PARAMETERS FOR Series 16i, 18i, 21i, AND 0i ..................................... 547
B.3 PARAMETERS FOR Power Mate i ........................................................... 549
B.4 PARAMETERS FOR Series 30i, 31i, AND 32i .......................................... 551
C FUNCTION-SPECIFIC SERVO PARAMETERS ................................. 553

D PARAMETERS RELATED TO HIGH-SPEED AND HIGH
PRECISION OPERATIONS ................................................................ 563
D.1 MODEL-SPECIFIC INFORMATION .......................................................... 564
D.1.1 Series 15i-MB.......................................................................................................564
D.1.2 Series 16i/18i/21i/0i/0i Mate-MB, 0i/0i Mate-MC/20i-FB ..................................567
D.1.3 Series 30i/31i/32i-A, 31i-A5 ................................................................................577
D.2 SERVO PARAMETERS RELATED TO HIGH-SPEED AND HIGH
PRECISION OPERATIONS....................................................................... 580
E VELOCITY LIMIT VALUES IN SERVO SOFTWARE ......................... 587
F SERVO FUNCTIONS .......................................................................... 593
G PARAMETERS FOR α AND OTHER SERIES ................................... 597
G.1 MOTOR ID NUMBERS OF α SERIES MOTORS...................................... 598
G.2 MOTOR ID NUMBERS OF β SERIES MOTORS ...................................... 600
G.3 MOTOR ID NUMBERS OF CONVENTIONAL LINEAR MOTORS ............ 601
G.4 PARAMETERS FOR SERVO HRV2 CONTROL ....................................... 602
G.5 HRV1 CONTROL PARAMETERS FOR α SERIES, β SERIES, AND
CONVENTIONAL LINEAR MOTORS........................................................ 603
G.6 HRV2 CONTROL PARAMETERS FOR βM SERIES MOTORS................ 612
H DETAILS OF HIGH-SPEED AND HIGH-PRECISION
ADJUSTMENT .................................................................................... 614
c-5
I SERVO CHECK BOARD OPERATING PROCEDURE ...................... 637

I.1 METHOD OF USING THE SERVO CHECK BOARD ................................ 638
I.2 ADJUSTING UNEXPECTED DISTURBANCE TORQUE DETECTION
WITH THE CHECK BOARD ...................................................................... 651
I.3 ADJUSTING LINEAR MOTOR AMR OFFSET WITH THE CHECK
BOARD (INCREMENTAL TYPE)............................................................... 652
I.4 ADJUSTING SMOOTHING COMPENSATION FOR A LINEAR MOTOR
WITH THE CHECK BOARD ...................................................................... 655
I.5 MEASURING FREQUENCY CHARACTERISTICS WITH THE CHECK
BOARD...................................................................................................... 661
J USING THE SERVO CHECK INTERFACE UNIT ............................... 665
c-6
B-65270EN/07 1.OVERVIEW
1 OVERVIEW
This manual describes the servo parameters of the CNC models using
FANUC AC SERVO MOTOR αiS, αiF, and βiS series. The
descriptions include the servo parameter start-up and adjustment
procedures. The meaning of each parameter is also explained.
Chapter 1, "OVERVIEW", consists of the following sections:
1.1 SERVO SOFTWARE AND SERVO CARDS SUPPORTED

BY EACH NC MODEL................................................................2
1.2 ABBREVIATIONS OF THE NC MODELS COVERED BY
THIS MANUAL ...........................................................................2
1.3 RELATED MANUALS................................................................2
-1-
1.OVERVIEW B-65270EN/07
1.1 SERVO SOFTWARE AND SERVO CARDS SUPPORTED

BY EACH NC MODEL
NC product name Series and edition of applicable servo software Servo card
Series 21i-MODEL B (Note1) Series 9096/A(01) and subsequent editions 320C52

Series 0i-MODEL B (Note1) Supporting i series CNC and SERVO HRV1 control) (Note2) servo card
Series 0i Mate-MODEL B (Note1)

Power Mate i-MODEL D (Note1)
Power Mate i-MODEL H (Note1) Series 90B0/H(08) and subsequent editions
Series 90B6/A(01) and subsequent editions
(Supporting i series CNC and SERVO HRV1, 2, and 3 control) 320C5410
(Note3) servo card
Series 15i-MODEL B
Series 90B1/A(01) and subsequent editions (Note4)
Series 16i-MODEL B
Series 18i-MODEL B

Series 0i-MODEL C (Supporting i series CNC and SERVO HRV1, 2, and 3 control)
320C5410
Series 0iMate-MODEL C (Note5)
servo card
Series 20i-MODEL B Series 90B8/I(09) and subsequent editions (Note6)
Series 90D0/A(01) and subsequent editions

Servo card for FS30i
(Supporting i series CNC and SERVO HRV4 control)
Series 30i-MODEL A servo HRV4 control
(Note7, Note8)
Series 31i-MODEL A
Series 90E0/A(01) and subsequent editions
Servo card for FS30i
(Supporting i series CNC and SERVO HRV2 and 3 control)
servo HRV2 and 3
(Note8)
Series 32i-MODEL A control
NOTE
1 The servo software series of the Series
21i-MODEL B, 0i-MODEL B, 0i Mate MODEL B,
or Power Mate i-MODEL D/H depends on the
incorporated servo card, as shown below:
Servo software Servo card
Series 9096 320C52 card
Series 90B0 or Series 90B6 320C5410 card
2 The servo software Series 9096 is compatible with

the conventional servo software Series 9090
except for the following function:
- Electric gear box (EGB) function can not be
used.
3 The servo software Series 90B0 is upwardly
compatible with the conventional servo software
Series 90A0. Series 90B6 is a successor of Series
-2-
NOTE
90B0.
4 Series 90B1 is a special series compatible with
Series 90B0 and is required when following
functions are used.
- PWM distribution module
- Pulse input DSA
- Magnetic pole detection
- Analog SDU
5 Servo software Series 90B5, which is a successor
of Series 90B0 and supports the same functions as
Series 90B6, is used in the Series 0i-MODEL C, 0i
Mate-MODEL C, and 20i-MODEL B.
6 Servo software Series 90B8, which is a successor
of Series 90B0 and supports the same functions as
Series 90B1, is used in the Series 0i-MODEL C
and 0i Mate-MODEL C.
7 When using servo HRV4 control with Series
30i-MODEL A and 31i-MODEL A, use Series
90D0.
8 Servo software Series 90D0 and 90E0 is upwardly
compatible with conventional servo software Series
90B0 except the following functions:
- Fine Acc./Dec. (FAD) function can not be used.
- HRV1 control can not be used.
-3-
Servo software series map
HRV1 supported, αi not supported
9090
HRV1 supported, αi supported
9096
HRV2 supported, αi not supported
90A0
90A6
HRV3 supported, αi supported
90B0
Support for pole detection, analog SDU, etc.
For Series 16i , For Series 0i-C For Series 16i ,

and so on and 20i-B and so on For Series 0i-C
90B6 90B5 90B1 90B8

For Series 30i ,
and so on
HRV4 supported
90E0 90D0
-4-
1.2 ABBREVIATIONS OF THE NC MODELS COVERED BY

THIS MANUAL
In this manual, the NC product names are abbreviated as follows.
NC product name Abbreviations

FANUC Series 30i-MODEL A Series 30i-A Series 30i
Series 30i
FS30i
Series 15i
FANUC Series 15i-MODEL B Series 15i-B Series 15i
FS15i
Series 20i
FANUC Series 20i-MODEL B Series 20i-B
FS20i
Series 16i and so on
FANUC Series 0i-MODEL C Series 0i-C
Series 16i etc.
FANUC Series 0i Mate-MODEL C Series 0i Mate-C Series 0i FS16i and so on
FANUC Series 0i-MODEL B Series 0i-B FS0i FS16i etc.
FANUC Series 0i Mate-MODEL B Series 0i Mate-B

Power Mate i-D
FANUC Power Mate i-MODEL D Power Mate i
PMi-D
Power Mate i-D/H
Power Mate i-H
FANUC Power Mate i-MODEL H (Note 1)
PMi-H
NOTE
1 In this manual, Power Mate i refers to the Power
Mate i-D, and Power Mate i-H.
-5-
1.3 RELATED MANUALS
The following manuals are available for FANUC AC SERVO

MOTOR αiS, αiF or βiS series.
In the table, this manual is marked with an asterisk (*).
Table 1.3 Related manuals of SERVO MOTOR αiS/αiF/βiS series

Document
Document name Major contents Major usage
number
FANUC AC SERVO MOTOR αi series
B-65262EN
DESCRIPTIONS
FANUC AC SERVO MOTOR βi series
B-65302EN • Specification
DESCRIPTIONS
• Characteristics • Selection of motor
FANUC LINEAR MOTOR LiS series
B-65222EN • External dimensions • Connection of motor
DESCRIPTIONS • Connections
FANUC SYNCHRONOUS BUILT-IN SERVO
MOTOR DiS series B-65332EN
DESCRIPTIONS
FANUC SERVO AMPLIFIER αiSV series • Specifications and functions
B-65282EN
DESCRIPTIONS • Installation • Selection of amplifier
• External dimensions and • Connection of
FANUC SERVO AMPLIFIER βiSV series
B-65322EN maintenance area amplifier
DESCRIPTIONS • Connections
FANUC AC SPINDLE MOTOR αi series
B-65285EN • Start up the system
FANUC SERVO AMPLIFIER αi series
• Start up procedure (Hardware)
MAINTENANCE MANUAL
• Troubleshooting • Troubleshooting
• Maintenance of motor • Maintenance of
FANUC AC SPINDLE MOTOR βi series motor
B-65325EN
FANUC SERVO AMPLIFIER βi series
MAINTENANCE MANUAL
B-65270EN *
FANUC SYNCHRONOUS BUILT-IN SERVO
• Start up the system
MOTOR DiS series • Initial setting
(Software)
PARAMETER MANUAL • Setting parameters
• Turning the system
FANUC AC SPINDLE MOTOR αi series • Description of parameters
(Parameters)
FANUC AC SPINDLE MOTOR βi series
FANUC BUILT-IN SPINDLE MOTOR B-65280EN
Bi series
PARAMETER MANUAL
-6-
Other manufactures’ products referred to in this manual

* IBM is registered trademark of International Business Machines
Corporation.
* MS-DOS and Windows are registered trademarks of Microsoft
Corporation.
All other product names identified throughout this manual are
trademarks or registered trademarks of their respective companies.
In this manual, the servo parameters are explained using the following
notation:
(Example)
Series 15i Servo parameter function name
No.1875(FS15i) Load inertia ratio
No.2021(FS30i, 16i)
Series 30i, 31i, 32i, 16i, 18i, 21i, 0i, Power Mate i
The following αi/βi Pulsecoders are available.
Pulsecoder name Resolution Type

αiA1000 1,000,000 pulse/rev Absolute
αiI1000 1,000,000 pulse/rev Incremental
αiA16000 16,000,000 pulse/rev Absolute
βiA128 131,072 pulse/rev Absolute
βiA64 65,536 pulse/rev Absolute
When parameters are set, these pulse coders are all assumed to have a
resolution of 1,000,000 pulses per motor revolution.
NOTE
The effect of αiA16000 can be increased when
used together with AI nano contour control.
-7-
2. SETTING αiS/αiF/βiS SERIES SERVO PARAMETERS B-65270EN/07
2 SETTING αiS/αiF/βiS SERIES SERVO

PARAMETERS
Chapter 2, "SETTING αiS/αiF/βiS SERIES SERVO
PARAMETERS", consists of the following sections:
2.1 INITIALIZING SERVO PARAMETERS....................................9

2.1.1 Before Servo Parameter Initialization.................................9
2.1.2 Parameter Initialization Flow............................................10
2.1.3 Servo Parameter Initialization Procedure .........................11
2.1.4 Setting Servo Parameters when a Separate Detector for
the Serial Interface is Used ...............................................33
2.1.5 Setting Servo Parameters when an Analog Input
Separate Detector Interface Unit is Used ..........................44
2.1.6 Setting Parameters when an αiCZ Sensor is Used ...........46
2.1.7 Setting Parameters when the PWM Distribution Module
is Used...............................................................................52
2.1.8 Actions for Illegal Servo Parameter Setting Alarms.........61
2.1.9 Notes on Using the Control Axis Detach Function ..........77
-8-
B-65270EN/07 2. SETTING αiS/αiF/βiS SERIES SERVO PARAMETERS
2.1 INITIALIZING SERVO PARAMETERS
2.1.1 Before Servo Parameter Initialization

Before starting servo parameter initialization, confirm the following:
<1> NC model (ex.: Series 16i-B)
<2> Servo motor model (ex.: αiF8/3000)
<3> Pulsecoder built in a motor (ex.: αiA1000)
<4> Is the separate position detector used? (ex.: Not used)
<5> Distance the machine tool moves per revolution of the motor
(ex.:10 mm per one revolution)
<6> Machine detection unit (ex.:0.001 mm)
<7> NC command unit (ex.:0.001 mm)
-9-
2.1.2 Parameter Initialization Flow

Use the procedure below to initialize the servo parameters.
For details of each setting item, see Subsection 2.1.3.
Preparation
- Turn on the power in the emergency stop state.
- Enable parameter writing.
- Display the servo setting screen. → See 2.1.3 (1).
Servo parameter setting

Description of setting Reference item
Initialization bit → 2.1.3 (2)
Motor ID No. setting → 2.1.3 (3)
AMR setting → 2.1.3 (4)
CMR setting → 2.1.3 (5)
Flexible feed gear setting → 2.1.3 (6)
Motor rotation direction setting → 2.1.3 (7)
Setting of the number of velocity pulses and the number → 2.1.3 (8)
of position pulses
Reference counter setting → 2.1.3 (9)
Full-closed system setting → 2.1.3 (10)
Servo loop gain setting → 2.1.3 (11)
CNC restart → 2.1.3 (12)
Absolute position detector setting → 2.1.3 (13)
Completion of servo parameter initialization
- 10 -
2.1.3 Servo Parameter Initialization Procedure
(1) Preparation
Switch on the NC in an emergency stop state.
Enable parameter writing (PWE = 1).
Initialize servo parameters on the servo setting screen.
For a Power Mate i with no CRT, specify a value for an item number
on the servo setting screen. See Fig. 2.1.3.
To display the servo setting screen, follow the procedure below, using
the key on the NC.
- Series 15i
Press the SYSTEM
function key several times, and the servo setting
screen will appear.
- Series 0i-C
Press the function key several times until the PARAMETER
SETTING SUPPORT screen appears.
Press soft key [(OPRT)], move the cursor to the SERVO SETTING
item, and press [SELECT] to display the PARAMETER SETTING
SUPPORT screen.
Fig. 2.1.3(a) PARAMETER SETTING SUPPORT screen
With 0i-C, two types of servo setting screens are available: the
standard screen and the conventional compatible screen. Initialization
can be performed by using either of the screens. This manual
describes the method of setting using the conventional compatible
screen.
For the standard screen, refer to "FANUC Series 0i-MODEL C/0i
Mate- MODEL C START-UP MANUAL (B-64114EN-1)".
- 11 -
(Standard screen) (Conventional compatible screen)
Fig. 2.1.3(b) 0i-C Servo tuning screen
When the servo setting screen (standard screen) is displayed, the servo
setting screen (conventional compatible screen) can be displayed by
operating the soft keys as follows:
[(OPRT)] → [ ] → [CHANGE]
- Series30i,31i,32i,16i,18i,21i,20i,0i-B
→ [SYSTEM] → [ ] → [SV-PRM]
If no servo screen appears, set the following parameter as shown, and

switch the NC off and on again.
#7 #6 #5 #4 #3 #2 #1 #0
3111 SVS
SVS (#0) 1: Displays the servo screen.
When the following screen appears, move the cursor to the item you
want to specify, and enter the value directly.
Power Mate
Servo set 01000 N0000
X axis Z axis
INITIAL SET BITS 00001010 00001010 No.2000
Motor ID No. 16 16 No.2020
AMR 00000000 00000000 No.2001
CMR 2 2 No.1820
Feed gear N 1 1 No.2084
(N/M) M 100 100 No.2085
Direction Set 111 111 No.2022
Velocity Pulse No. 8192 8192 No.2023
Position Pulse No. 12500 12500 No.2024
Ref. counter 10000 10000 No.1821
Fig. 2.1.3(c) Servo setting screen Correspondence of Power Mate i
- 12 -
(2) Initialization
Start initialization.
Do not power off the NC until step (12).
#7 #6 #5 #4 #3 #2 #1 #0
INITIAL SET BIT PRMC DGPR PLC0
( Note)
Reset initialization bit 1 to 0.

DGPR(#1)=0
After initialization is completed, DGPR (#1) is set to 1.
NOTE
Once initialization has been completed, bit 3
(PRMC) for initialization is automatically set to 1.
(Except Series 30i, 31i and 32i)
(3) Motor ID No. setting

Specify the motor ID number.
Select the motor ID number of a motor to be used according to the
motor model and motor specification (the middle four digits in
A06B-****-B***) listed in the following tables.
When using servo HRV3 or HRV4 control, please use the motor ID
number for servo HRV2 control. It is available with the series and
editions listed in the table and later editions.
The mark "x" indicates a value that varies depending on the used
options.
The mark "-" indicates that automatic loading of standard parameters
is not supported as of August, 2007.
NOTE
• Series 30i, 31i and 32i
Specify the motor ID number for servo HRV2 control.
• Other than the Series 30i, 31i and 32i
When a pair of the values set in parameter No. 1023 (servo axis number) are
consecutive odd and even numbers, set motor ID numbers for servo HRV control of
the same type.
(Correct examples)
Servo axes when parameter No.1023= 1,2: Motor ID number for servo HRV2 control
(Wrong examples)
Servo axes when parameter No.1023= 1: Motor ID number for servo HRV2 control
• With servo software Series 9096, only servo HRV1 control can be used. Be sure to
specify a motor ID number for servo HRV1 control.
- 13 -
αiS series servo motor

Motor Motor ID No. 90D0 90B5 90B1
Motor model 90B0 9096
specification HRV1 HRV2 90E0 90B6 90B8
αiS2/5000 0212 162 262 A H A A A
αiS2/6000 0218 - 284 G - B B -
αiS4/5000 0215 165 265 A H A A A
αiS8/4000 0235 185 285 A H A A A
αiS8/6000 0232 - 290 G - B B -
αiS12/4000 0238 188 288 A H A A A
αiS22/4000 0265 215 315 A H A A A
αiS30/4000 0268 218 318 A H A A A
αiS40/4000 0272 222 322 A H A A A
αiS50/3000 0275-Bx0x 224 324 B V A A F
αiS50/3000 FAN 0275-Bx1x 225 325 A N A A D
αiS100/2500 0285 235 335 A T A A F
αiS100/2500 FAN 0285 230 330 P - - I -
αiS200/2500 0288 238 338 A T A A F
αiS200/2500 FAN 0288 234 334 P - - I -
αiS300/2000 0292 115 342 B V A A -
αiS500/2000 0295 245 345 A T A A F
αiF series servo motor

αiF1/5000 0202 152 252 A H A A A
αiF2/5000 0205 155 255 A H A A A
αiF4/4000 0223 173 273 A H A A A
αiF8/3000 0227 177 277 A H A A A
αiF12/3000 0243 193 293 A H A A A
αiF22/3000 0247 197 297 A H A A A
αiF30/3000 0253 203 303 A H A A A
αiF40/3000 0257-Bx0x 207 307 A H A A A
αiF40/3000 FAN 0257-Bx1x 208 308 A I A A C
- 14 -
αiS series servo motor (for 400-V driving)

αiS2/5000HV 0213 163 263 A Q A A D
αiS2/6000HV 0219 - 287 G - B B -
αiS4/5000HV 0216 166 266 A Q A A D
αiS8/4000HV 0236 186 286 A N A A D
αiS8/6000HV 0233 - 292 G - B B -
αiS12/4000HV 0239 189 289 A N A A D
αiS22/4000HV 0266 216 316 A N A A D
αiS30/4000HV 0269 219 319 A N A A D
αiS40/4000HV 0273 223 323 A N A A D
αiS50/3000HV FAN 0276-Bx1x 226 326 A N A A D
αiS50/3000HV 0276-Bx0x 227 327 B V A A F
αiS100/2500HV 0286 236 336 B V A A F
αiS100/2500HV FAN 0286 231 331 P - - I -
αiS200/2500HV 0289 239 339 B V A A F
αiS200/2500HV FAN 0289 237 337 P - - I -
αiS300/2000HV 0293 243 343 B V A A F
αiS500/2000HV 0296 246 346 B V A A F
αiS1000/2000HV 0298 248 348 B V A A F
αiS2000/2000HV (Note 1)
0091 - 340 J - B B -
NOTE
1 The model needs manual setting. (See Subsection 4.16.3, "Setting
Parameters in the PWM Distribution Module Configuration".)
When using the torque control function, contact FANUC.
αiF series servo motor (for 400-V driving)

αiF4/4000HV 0225 175 275 A Q A A E
αiF8/3000HV 0229 179 279 A Q A A E
αiF12/3000HV 0245 195 295 A Q A A E
αiF22/3000HV 0249 199 299 A Q A A E
- 15 -
αCi series servo motor

αC4/3000i 0221 171 271 A H A A A
αC8/2000i 0226 176 276 A H A A A
αC12/2000i 0241 191 291 A H A A A
αC22/2000i 0246 196 296 A H A A A
αC30/1500i 0251 201 301 A H A A A
βiS series servo motor

Motor Amplifier Motor ID No. 90D0 90B5 90B1
specification driving HRV1 HRV2 90E0 90B6 90B8
βiS0.2/5000 0111
(Note 1)
4A - 260 A N A A *
βiS0.3/5000 0112
(Note 1)
4A - 261 A N A A *
βiS0.4/5000 0114
(Note 1)
20A - 280 A N A A *
βiS0.5/6000 0115 20A 181 281 G - B B -
βiS1/6000 0116 20A 182 282 G - B B -
20A 153 253 B V A A F
βiS2/4000 0061
(Note 2)
40A 154 254 B V A A F
20A 156 256 B V A A F
βiS4/4000 0063
(Note 2)
40A 157 257 B V A A F
20A 158 258 B V A A F
βiS8/3000 0075
(Note 2)
40A 159 259 B V A A F
20A 169 269 K - D E -
βiS12/2000 0077
(Note 2)
40A 168 268 P - - - -
βiS12/3000 0078 40A 172 272 B V A A F
βiS22/2000 0085 40A 174 274 B V A A F
NOTE
1 HRV1 control cannot be used with these motors. So, these motors
cannot be used with Series 9096.
2 For a motor specification suffixed with “-Bxx6”, be sure to use
parameters dedicated to FS0i.
- 16 -
βiS series servo motor (for 400-V driving)

Motor Amplifier Motor ID No. 90D0 90B5 90B1
specification driving HRV1 HRV2 90E0 90B6 90B8
βiS2/4000HV 0062 10A 151 251 J - B C -
βiS4/4000HV 0064 10A 164 264 J - B C -
βiS8/3000HV 0076 10A 167 267 J - B C -
βiS12/3000HV 0079 20A 170 270 J - B C -
βiS22/2000HV 0086 20A 178 278 J - B C -
βiS series servo motor (dedicated to FS0i)

Motor Amplifier Motor ID No.
Motor model 90B5 90B8
specification driving HRV1 HRV2
20A 206 306 D I

βiS 2/4000 0061-Bxx6
40A 210 310 D I
20A 211 311 D I
βiS 4/4000 0063-Bxx6
40A 212 312 D I
20A 183 283 D I
βiS 8/3000 0075-Bxx6
40A 194 294 D I
20A 198 298 D I
βiS 12/2000 0077-Bxx6
40A 200 300 - -
20A 202 302 D I
βiS 22/1500 0084-Bxx6
40A 205 305 D I
The motor models above can be driven only with Series 90B5 and
90B8.
- 17 -
Linear motor
Linear motor parameters for servo HRV2 control
Note: The following linear motors are driven by 200V.
Motor 90D0 90B5
Motor model Motor ID No. 90B0 90B1 9096
specification 90E0 90B6
LiS 300A1/4 0441-B200 351 G - B B -
LiS 600A1/4 0442-B200 353 G - B B -
LiS 900A1/4 0443-B200 355 G - B B -
LiS 1500B1/4 0444-B210 357 G - B B -
LiS 3000B2/2 0445-B110 360 G - B B -
LiS 3000B2/4 0445-B210 362 G - B B -
LiS 4500B2/2 0446-B110 364 G - B B -
LiS 6000B2/2 0447-B110 368 G - B B -
LiS 6000B2/4 0447-B210 370 G - B B -
LiS 7500B2/2 0448-B110 372 G - B B -
LiS 7500B2/4 0448-B210 374 G - B B -
LiS 9000B2/2 0449-B110 376 G - B B -
LiS 9000B2/4 0449-B210 378 G - B B -
LiS 3300C1/2 0451-B110 380 G - B B -
LiS 9000C2/2 0454-B110 384 G - B B -
LiS 11000C2/2 0455-B110 388 G - B B -
LiS 15000C2/2 0456-B110 392 G - B B -
LiS 15000C2/3 0456-B210 394 G - B B -
LiS 10000C3/2 0457-B110 396 G - B B -
LiS 17000C3/2 0459-B110 400 G - B B -
Note: The following linear motors are driven by 400V.

Motor 90D0 90B5
LiS 1500B1/4 0444-B210 358 G - B B -
LiS 3000B2/2 0445-B110 361 G - B B -
LiS 4500B2/2HV 0446-B010 363 G - B B -
LiS 4500B2/2 0446-B110 365 G - B B -
LiS 6000B2/2HV 0447-B010 367 G - B B -
LiS 6000B2/2 0447-B110 369 G - B B -
LiS 7500B2/2HV 0448-B010 371 G - B B -
LiS 7500B2/2 0448-B110 373 G - B B -
LiS 9000B2/2 0449-B110 377 G - B B -
LiS 3300C1/2 0451-B110 381 G - B B -
LiS 9000C2/2 0454-B110 385 G - B B -
LiS 11000C2/2HV 0455-B010 387 G - B B -
LiS 11000C2/2 0455-B110 389 G - B B -
LiS 15000C2/3HV 0456-B010 391 G - B B -
LiS 10000C3/2 0457-B110 397 G - B B -
LiS 17000C3/2 0459-B110 401 G - B B -
- 18 -
Linear motor parameters for servo HRV1 control

Motor 90D0 90B5
LiS 1500B1/4 0444-B210 90 A A A A A
LiS 3000B2/2 0445-B110 91 A A A A A
LiS 6000B2/2 0447-B110 92 A A A A A
LiS 9000B2/2 0449-B110 93 A A A A A
LiS 1500C2/2 0456-B110 94 A A A A A
LiS 3000B2/4 0445-B210 120 A A A A A
LiS 6000B2/4 0447-B210 121 A A A A A
LiS 9000B2/4 0449-B210 122 A A A A A
LiS 15000C2/3 0456-B210 123 A A A A A
LiS 300A1/4 0441-B200 124 A A A A A
LiS 600A1/4 0442-B200 125 A A A A A
LiS 900A1/4 0443-B200 126 A A A A A
127 A A A D
LiS 6000B2/4 0412-B811 R
(160-A driving)
128 A A A D
LiS 9000B2/2 0413 N
(160-A driving)
129 A A A D
LiS 9000B2/4 0413-B811 Q
(360-A driving)
130 A A A D
LiS 15000C2/2 0414 Q
(360-A driving)
(Reference)
The parameter table presented in Chapter 6 has two motor ID Nos. for
the same linear motor. One of the two is for driving the α series servo
amplifiers (130A and 240A). Be careful not to use the wrong ID No.
α servo amplifier driving αi servo amplifier driving

Motor model Amplifier Amplifier
maximum Motor ID No. maximum Motor ID No.
current [A] current [A]
LiS 6000B2/4 240 121 160 127
LiS 9000B2/2 130 93 160 128
LiS 9000B2/4 240 122 360 129
LiS 15000C2/2 240 94 360 130
- 19 -
Synchronous built-in servo motor

Synchronous built-in servo motor for servo HRV2 control
NOTE: The following synchronous built-in servo motors are
driven by 200V.
Motor 90D0 90B5 90B1
Motor model Motor ID No. 90B0 9096
specification 90E0 90B6 90B8
DiS 22/600 0482-B10x 421 P - - I -
DiS 85/400 0483-B20x 423 N - - H -
DiS 85/1000 0483-B22x 443 P - - K -
DiS 110/300 0484-B10x 425 N - - H -
DiS 110/1000 0484-B12x 445 P - - K -
DiS 260/300 0484-B30x 427 N - - H -
DiS 260/600 0484-B31x 429 N - - H -
DiS 260/1000 0484-B32x 447 P - - K -
DiS 370/300 0484-B40x 431 N - - H -
DiS 1200/250 0485-B50x 435 N - - H -
DiS 1500/200 0486-B30x 437 N - - H -
DiS 2100/150 0487-B30x 439 N - - H -
DiS 3000/150 0487-B40x 441 N - - H -
NOTE: The following synchronous built-in servo motors are

driven by 400V.
Motor 90D0 90B5 90B1
specification 90E0 90B6 90B8
DiS 22/600 0482-B10x 422 P - - I -
DiS 85/400 0483-B20x 424 N - - H -
DiS 110/300 0484-B10x 426 N - - H -
DiS 260/300 0484-B30x 428 N - - H -
DiS 260/600 0484-B31x 430 N - - H -
DiS 370/300 0484-B40x 432 K - - H -
DiS 1200/250 0485-B50x 436 N - - H -
DiS 1500/200 0486-B30x 438 N - - H -
DiS 2100/150 0487-B30x 440 N - - H -
DiS 3000/150 0487-B40x 442 N - - H -
- 20 -
(4) AMR setting

Set, as AMR, a setting value of following table.
Motor type AMR setting
αiS/αiF/βiS motor 00000000
(other than αiS2000HV and αiS3000HV)
αiS2000HV,αiS3000HV 00001000
Linear motor (Note 1)
Synchronous built-in servo motor (Note 2)
NOTE
1 When using a linear motor, set AMR according to
the description in Section 4.14, "LINEAR MOTOR
PARAMETER SETTING".
2 When using a synchronous built-in servo motor, set
AMR according to the description in Section 4.15,
"SYNCHRONOUS BUILT-IN SERVO MOTOR
PARAMETER SETTING".
(5) CMR setting

Set, as CMR, a specified magnification for the amount of movement
from the NC to the servo system.
CMR = Command unit / Detection unit
CMR 1/2 to 48 Setting value = CMR × 2
Usually, set CMR with 2, because command unit = detection unit

(CMR = 1).
(6) Flexible feed gear setting

Specify the flexible feed gear (F⋅FG). This function makes it easy to
specify a detection unit for the leads and gear reduction ratios of
various ball screws by changing the number of position feedback
pulses from the Pulsecoder or separate detector. It converts the
incoming number of pulses from the position detector so that it
matches the commanded number of pulses. When using a linear motor,
set F⋅FG according to the description in Section 4.14, "LINEAR
MOTOR PARAMETER SETTING". When using a synchronous
built-in servo motor, set F⋅FG according to the description in Section
4.15, "SYNCHRONOUS BUILT-IN SERVO MOTOR
PARAMETER SETTING".
(a) Semi-closed feedback loop

Setting for the αi Pulsecoder
↓ (Note 1) Necessary position feedback pulses

F⋅FG numerator (≤ 32767) per motor revolution
= (as irreducible fraction)
F⋅FG denominator (≤ 32767) 1,000,000 ← (Note 2)
- 21 -
NOTE
1 For both F⋅FG numerator and denominator, the maximum setting
value (after reduced) is 32767.
2 αi Pulsecoders assume one million pulses per motor revolution,
irrespective of resolution, for the flexible feed gear setting.
3 If the calculation of the number of pulses required per motor
revolution involves π, such as when a rack and pinion are used,
assume π to be approximately 355/113.
Example of setting
If the ball screw used in direct coupling has a lead of 5 mm/rev and
the detection unit is 1 µm
The number of pulses generated per motor turn (5 mm) is:
5/0.001 = 5000 (pulses)
Because the αi Pulsecoder feeds back 1000000 pulses per motor turn:
FFG = 5000 / 1000000 = 1 / 200
Other FFG (numerator/denominator) setting examples, where the gear

reduction ratio is assumed to be 1:1
Detection Ball screw lead
unit 6mm 8mm 10mm 12mm 16mm 20mm
1µm 6 / 1000 8 / 1000 10 / 1000 12 / 1000 16 / 1000 20 / 1000
0.5µm 12 / 1000 16 / 1000 20 / 1000 24 / 1000 32 / 1000 40 / 1000
0.1µm 60 / 1000 80 / 1000 100 / 1000 120 / 1000 160 / 1000 200 / 1000
Example of setting
If the gear reduction ratio between the rotary axis motor and table is
10:1 and the detection unit is 1/1000 degrees
The table rotates through 360/10 degrees when the motor makes one
turn.
The number of position pulses necessary for the motor to make one
turn is:
360/10 ÷ (1/1000) = 36,000 pulses
F⋅FG numerator 36,000 36
= =
F⋅FG denominator 1,000,000 1,000
If the gear reduction ratio between the rotary axis motor and table is
300:1 and the detection unit is 1/10000 degrees
The table rotates through 360/300 degrees when the motor makes one
turn.
turn is:
360/300 ÷ (1/10000) = 12,000 pulses
F⋅FG numerator 12,000 12
= =
F⋅FG denominator 1,000,000 1,000
- 22 -
(b) Full-closed feedback loop

Setting for use of a separate detector (full-closed)
Number of position pulses corresponding

F⋅FG numerator (≤ 32767) to a predetermined amount of travel
= (as irreducible fraction)
F⋅FG denominator (≤ 32767) Number of position pulses corresponding
to a predetermined amount of travel from
a separate detector
Example of setting
To detect a distance of 1-µm using a 0.5-µm scale, set the following:
(L represents a constant distance.)
Numerator of F⋅FG L/1 1
= =
Denominator of F⋅FG L/0.5 2
Other FFG (numerator/denominator) setting examples

Scale resolution
Detection unit
1 µm 0.5 µm 0.1 µm 0.05 µm
1µm 1/1 1/2 1 / 10 1 / 20
0.5µm - 1/1 1/5 1 / 10
0.1µm - - 1/1 1/2
NOTE
The maximum rotation speed allowable with servo
software depends on the detection unit. (See
Appendix E, "VELOCITY LIMIT VALUES IN SERVO
SOFTWARE".) Select a detection unit that enables a
requested maximum rotation speed to be realized.
When a speed of up to 6000 revolutions is used as a
live tool in the direct motor connection mode, in
particular, use a detection unit of 2/1000 deg (IS-B
setting, CMR=1/2, flexible feed gear=18/100).
(7) Motor rotation direction setting

Set the direction in which the motor is to turn when a positive value is
specified as a move command. For linear motors, set the parameter
according to the description in Section 4.14, "LINEAR MOTOR
PARAMETER SETTING". For synchronous built-in servo motors, set
the parameter according to the description in Section 4.15,
"SYNCHRONOUS BUILT-IN SERVO MOTOR PARAMETER
SETTING".
111 Clockwise as viewed from the Pulsecoder
−111 Counterclockwise as viewed from the Pulsecoder
Counterclockwise as FANUC Clockwise as viewed from

viewed from the the Pulsecoder
Pulsecoder Set 111.
Set -111.
- 23 -
(8) Specify the number of velocity pulses and the number of position pulses.
Set the number of velocity pulses and the number of position pulses
according to the connected detector. For linear motors, set these
parameters according to the description in Section 4.14, "LINEAR
MOTOR PARAMETER SETTING". For synchronous built-in servo
motors, set these parameters according to the description in Section
4.15, "SYNCHRONOUS BUILT-IN SERVO MOTOR
PARAMETER SETTING".
(a) Number of velocity pulses

Set the number of velocity pulses to 8192.
αiS/αiF/βiS motor 8192
(b) Number of position pulses

(b)-1 Number of position pulses for semi-closed feedback loop
Set the number of position pulses to 12500.
Number of position pulses
12500
(αiS/αiF/βiS motor, semi-closed feedback loop)
(b)-2 Number of position pulses for full-closed feedback loop

(See Subsections 2.1.4 and 2.1.5)
Set the number of position pulses to the number of pulses fed back
from the separate detector when the motor makes one turn. (The
flexible feed gear has nothing to do with the calculation of the number
of position pulses).
Number of position pulses Number of pulses fed back from the separate
(full-closed feedback loop) detector when the motor makes one turn
When using a serial rotary scale with a resolution of 1,000,000 pulses

per revolution, set a value assuming that 12500 is equivalent to
1,000,000 pulses.
(full-closed feedback loop) 12,500 ×(motor-table gear reduction ratio)
(*) 1,000,000 pulses / rev
Example 1:
Parallel type, serial linear scale
If the ball screw used in direct coupling has a lead of 10 mm and
the separate detector used has a resolution of 0.5 µm per pulse
Number of position pulses = 10 / 0.0005 = 20,000
Example 2:
Serial rotary scale
If the motor-table gear reduction ratio is 10:1,
Number of position pulses = 12,500 × (1/10) = 1250
- 24 -
(b)-3 If the setting for the number of position pulses is larger than 32767
If the number of position pulses exceeds 32767, set the following
parameter:
2628 (FS15i) Conversion coefficient for the number of position feedback pulses
2185 (FS30i,16i)
Series 90E0, Series 90D0, Series 90B0, Series 90B5, Series 90B6,
Series 90B1 :
Set the number of position pulses with a product of two
parameters, using the conversion coefficient for the number of
position feedback pulses.
Number of pulses from separate
Position pulse setting = detector per motor revolution
Position pulse conversion coefficient
* The number of velocity pulses need not be changed.
Series 9096 :
No conversion coefficient for the number of position feedback
pulses can be used. As usual, set the initialization bit 0 to 1, and
set the number of velocity pulses and the number of position
pulses to 1/10 the respective values stated earlier.
Number of pulses from separate
Position pulse setting = detector per motor revolution
10
Number of velocity pulses to be set

Velocity pulse setting = originally
10
= 819 (In the case of αiS/αiF/βiS motor)
→ See Supplementary 3 of Subsection 2.1.8.
- 25 -
NOTE
By setting initialization bit 0 (of No. 2000 (FS30i, 16i,
etc.)/No. 1804 (FS15i)) to 1, the number of velocity pulses
and the number of position pulses can be internally
increased by a factor of 10. Usually, however, set bit 0 of
No. 2000 to 0. If the number of position pulses is beyond
the setting range, use a position pulse conversion
coefficient. Only in the situations indicated below, set bit 0
of No. 2000 to 1, set the number of velocity pulses to
one-tenth of the value to be originally set, and also set the
number of position pulses to one-tenth of the value to be
originally set.
- When the number of velocity pulses exceeds 32767
because a high-resolution detector is used with a linear
motor or synchronous built-in servo motor
- When the parameter for specifying a position pulse
conversion coefficient is unusable because servo
software Series 9096 is used
- 26 -
(9) Reference counter setting

Specify the reference counter.
The reference counter is used in making a return to the reference
position by a grid method.
(a) Semi-closed loop

(Linear axis)
Number of position pulses corresponding to a
Count on the reference
= single motor revolution or the same number
counter
divided by an integer value
(Rotary axis)
Number of position pulses corresponding to a
Count on the reference
= single motor revolution/M, or the same
counter
number divided by an integer value
* When the motor-table gear reduction ratio is M/N (M and N are integers,
and M/N is a fraction that is reduced to lowest terms.)
NOTE
1 If the calculation above results in a fraction, a
setting can be made with a fraction.
See (a)-1.
2 If the rotation ratio between the motor and table on
the rotary axis is not an integer, the reference
counter capacity needs to be set so that the point
(grid point) where the reference counter equals 0
appears at the same position relative to the table.
So, with the rotary axis, the number of position
pulses per motor revolution needs to be multiplied
by 1/M.
Example of setting
αi Pulsecoder and semi-closed loop (1-µm detection)
Necessary number of
Ball screw lead Reference Grid width
position pulses
(mm/revolution) counter (mm)
(pulse/revolution)
10 10000 10000 10
20 20000 20000 20
30 30000 30000 30
When the number of position pulses corresponding to a single motor

revolution does not agree with the reference counter setting, the
position of the zero point depends on the start point.
In such a case, set the reference counter capacity with a fraction to
change the detection unit and eliminate the error in the reference
counter. (Except Series 9096)
Example of setting
System using a detection unit of 1 µm, a ball screw lead of 20
mm/revolution, and a gear reduction ratio of 1/17
To eliminate the error of the reference counter, two methods of setting
are available:
- 27 -
(a)-1 Method that sets a reference counter capacity with a fraction

(a)-2 Method that changes the detection unit
An example of each setting method is explained below.
(a)-1 Method of specifying the reference counter capacity with a fraction (except
Series 9096)
turn is: 20000/17
Set the following parameter as stated below.
1896 (FS15i) Reference counter capacity (numerator)

1821 (FS30i, 16i)
[Valid data range] 0 to 99999999
Set the numerator of a fraction for the reference counter capacity.
2622 (FS15i) Reference counter capacity (denominator)

2179 (FS30i, 16i)
A value up to around 100 is assumed to be set as the denominator of
the reference counter capacity. Note that if a larger value is set, the
grid width becomes too small, which makes it difficult to perform
reference position return by grid method.
The denominator parameter is not indicated in the servo setting screen,
so it must be set in the parameter screen.
In this example, set the numerator and denominator, respectively, to
20000 and 17.
NOTE
Even if a setting is made with a fraction, set the
number of position pulses per motor revolution/M for
a semi-closed loop rotary axis when the reduction
ratio is M/N.
Reference counter =
Number of position pulses per motor revolution/M, or
The same number divided by an integer
- 28 -
(a)-2 Method of changing the detection unit

turn is: 20000/17
In this case, increase all the following parameter values by a factor of
17, and set the detection unit to 1/17 µm.
Series 30i,15i,16i,0i, Power Mate i,
Parameter modification
and so on
FFG Servo screen
CMR Servo screen
Reference counter Servo screen
Effective area Nos. 1826, 1827
Position error limit in traveling No. 1828
Position error limit in the stop state No. 1829
Backlash Nos. 1851, 1852
Changing the detection unit from 1 µm to 1/17 µm requires
multiplying each of the parameter settings made for the detection unit
by 17.
CAUTION
In addition to the above parameters, there are
some parameters that are to be set in detection
units. For details, see Appendix B.
Making these modifications eliminates the difference between the
number of position pulses corresponding to a single motor revolution
and the reference counter setting.
Number of position pulses corresponding to a single motor revolution
= 20000
Reference counter setting = 20000
(b) Full-closed loop (See Subsections 2.1.4 and 2.1.5)

Z-phase (reference-position) interval divided by the
Reference
= detection unit, or this value sub-divided by an integer
counter setting
value
NOTE
If the separate detector-table rotation ratio for the
rotary axis is not an integer, it is necessary to set
the reference counter capacity in such a way that
points where reference counter = 0 (grid points)
appear always at the same position for the table.
Example of setting
Example 1) When the Z-phase interval is 50 mm and the detection
unit is 1 µm:
Reference counter setting = 50,000/1 = 50,000
Example 2) When a rotary axis is used and the detection unit is
0.001 degrees:
Reference counter setting = 360/0.001 = 360,000
Example 3) When a linear scale is used and a single Z phase exists:
Set the reference counter to 10000, 50000, or another
round number.
- 29 -
If the calculated value of the reference counter capacity is not an

integer, the reference counter capacity can be set as a fraction as in the
case of a semi-closed loop. For details of parameters, see (a)-1.
NOTE
The following value can be set as a reference
counter capacity:
(For linear axis)
Number of position pulses corresponding to the
Z-phase interval of a separate detector (or the
same number divided by an integer)
(For rotary axis)
Number of position pulses per revolution of a
separate detector/M (or the same number divided
by an integer)
(*) When the rotation ratio between the table and
separate detector is M/N (M and N are
integers, and M/N is a fraction that is reduced
to lowest terms.)
(10) Full-closed system setting (go to (11) if a semi-closed system is in use)

For a full-closed system, it is necessary to set the following function
bit.
(a) Setting required with all CNC Series

#7 #6 #5 #4 #3 #2 #1 #0
1815 (FS15i) OPTX
1815 (FS30i, 16i, etc) ↑ To be specified for
every NC.
OPTX(#1) The separate position detector is:
0: Not to be used
1: To be used
(b) Setting required with only the Series 15i

When the Series 15i is used, the following function bit (PFSE) needs
to be set to 1 in addition to OPTX.
#7 #6 #5 #4 #3 #2 #1 #0
1807 (FS15i) PFSE
↑ To be specified only for the Series 15i
PFSE(#3) The separate position detector is:
0: Not to be used
1: To be used
- 30 -
(11) Servo loop gain setting

Set a value other than 0 as a servo loop gain. Usually, set an initial
value of 3000. (This initial value is adjusted later as needed.)
Servo loop gain 3000 (guideline)
NOTE
1 When a servo loop gain of 0 is set, an illegal
servo parameter setting alarm is issued.
2 If there is a problem such as vibration occurring at
the time of motor rotation after the NC is started,
perform servo tuning according to Chapter 3.
(12) NC restart
Switch the NC off and on again.
This completes servo parameter initialization.
If an illegal servo parameter setting alarm occurs, go to Subsec. 2.1.8.
If a servo alarm related to Pulsecoders occurs for an axis for which a
servo motor or amplifier is not connected, specify the following
parameter.
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) DMY
2009 (FS30i, 16i)
DMY (#0) The serial feedback dummy function is: (See Section 4.9, “SERIAL
FEEDBACK DUMMY FUNCTIONS” for function detail)
0 : Not used
1 : Used
- 31 -
(13) Absolute position detector setting

When you are going to use an αi/βi Pulsecoder as an absolute
Pulsecoder, use the following procedure.
Procedure
1. Specify the following parameter, then switch the NC off.
#7 #6 #5 #4 #3 #2 #1 #0
1815 (FS15i) APCx
1815 (FS30i, 16i)
APCx (#5) The absolute position detector is:
0: Not used
1: Used
2. After making sure that the battery for the Pulsecoder is connected,
turn off the CNC.
3. A request to return to the reference position is
These steps
displayed. were added
4. Cause the servo motor to make one turn by jogging. for the αi/βi
5. Turn off and on the CNC. Pulsecoder.
6. A request to return to the reference position is
displayed.
7. Do the reference position return.
- 32 -
2.1.4 Setting Servo Parameters when a Separate Detector for the

Serial Interface is Used
(1) Overview
This subsection describes the setting of servo parameters for using a
separate detector of serial output type. Perform parameter setting as
described below according to the classification (model and
configuration) of the serial detector used.
(2) Series and editions of applicable servo software

(Series 30i,31i,32i)
(Series 15i-B,16i-B,18i-B,21i-B,0i-B,0i Mate-B,Power Mate i)
(Series 0i-C,0i Mate-C,20i-B)
(3) Classification of serial detectors and usable detector examples

Usable separate detectors for the serial interface are classified into
four major types as shown below. Note that parameter settings vary
with these types.
(a) Serial output type linear encoder

Minimum resolution Model Backup
Mitutoyo Co., Ltd. 0.05µｍ AT353, AT553 Not required
0.05µｍ/0.1µｍ LC191F Not required
HEIDENHAIN
0.05µｍ/0.1µｍ LC491F Not required
(b) Analog output type linear encoder + FANUC high-resolution serial output
circuit
Signal pitch Model Backup
Mitutoyo Co., Ltd. 20µｍ AT402 Required
HEIDENHAIN 20µｍ LS486, LS186 Required
Sony Precision Technology Inc. 20µｍ SH12 Required
(c) Serial output type rotary encoder

Minimum resolution (Note 1) Model Backup
FANUC 220 pulse/rev αA1000S Required
- 33 -
(d) RCN220, RCN223, RCN723, and RCN727 manufactured by HEIDENHAIN

Minimum resolution (Note 1) Model Backup
20
HEIDENHAIN 2 pulse/rev RCN220 Not required
223 pulse/rev RCN223, 723 Not required
227 pulse/rev RCN727 Not required
NOTE
1 The minimum resolution of a rotary encoder is the resolution of the
encoder itself. For the FANUC systems, however, please set
parameters with regarding the number of pulses/rev as follows:
One million pulses/rev for a minimum resolution of 220 pulses/rev
Eight million pulses/rev for a minimum resolution of 223 pulses/rev
Eight million pulses/rev for a minimum resolution of 227 pulses/rev
(4) Setting parameters

Set the following parameters according to the type of the detector
(described in the previous item).
(a) Parameter setting for a linear encoder of a serial output type
(Parameter setting method)

In addition to the conventional settings for a separate detector (bit 1 of
parameter No. 1815 (Series30i,15i,16i,18i,21i,20i,0i, and Power Mate
i), bit 3 of parameter No. 1807 (Series 15i), and if needed, FSSB),
note the following parameters:
[Flexible feed gear]

Parameter Nos. 1977 and 1978 (Series 15i) or Nos. 2084 and 2085
(Series 30i, 16i and so on)
Flexible feed gear (N/M) =
Minimum resolution of detector [µm] / controller detection unit [µm]
[Number of position pulses]

Parameter No. 1891 (Series 15i) or No. 2024 (Series 30i, 16i and so
on)
Number of position pulses =
Amount of movement per motor revolution [mm] /
detection unit of the sensor [mm]
* If the result of the above calculation does not fall in the setting
range (0 to 32767) for the number of position pulses, use
“position feedback pulse conversion coefficient” to specify the
number of position pulses according to the following procedure.
Number of position pulses to be set = A × B
Select B so that A is within 32767. Then, set the following:
A: Position pulses parameter (32767 or less)
No.1891 (Series15i), No.2024 (Series 30i, 16i and so on)
B: Position pulses conversion coefficient parameter
- 34 -
(Example of parameter setting)

[System configuration]
• The Series 16i is used.
• A linear scale with a minimum resolution of 0.1 µm is used.
• The least input increment of the controller is 1 µm.
• The amount of movement per motor revolution is 16 mm.
[Parameter setting]
• To enable a separate detector, set bit 1 of parameter No. 1815 to
1.
• Calculate the parameters for the flexible feed gear.
Because flexible feed gear (N/M) = 0.1 µm/1 µm = 1/10:
No. 2084 = 1 and No. 2085 = 10
• Calculate the number of position pulses.
Number of position pulses = 16 mm/0.0001mm = 160000
Because this result does not fall in the setting range (0 to 32767),
set A and B, respectively, with the "number of position pulses"
and "position pulses conversion coefficient" by assuming:
160,000 = 10,000 × 16 → A = 10,000 and B = 16
No.2024 = 10,000, No.2185 = 16
(b) Parameter setting for analog output type linear encoder +

FANUC high-resolution serial output circuit

In addition to the conventional separate detector settings (bit 1 of
parameter No. 1815 (Series15i,30i,16i,18i,21i,20i,0i, and Power Mate
i), bit 3 of parameter No. 1807 (Series 15i), and, if necessary, FSSB
setting), pay attention to the following parameter settings.
First check the type of the FANUC high-resolution output circuit to be

coupled to the linear encoder, and then determine the settings of the
following function bits.
[Function bit]
Interpolation
Circuit Specification
magnification
High-resolution serial output circuit A860-0333-T501 512
High-resolution serial output circuit H A860-0333-T701 2048
High-resolution serial output circuit C A860-0333-T801 2048
- 35 -
#7 #6 #5 #4 #3 #2 #1 #0
2687 (FS15i) HP2048
2274 (FS30i, 16i)
HP2048(#0) The 2048-magnification interpolation circuit (high-resolution serial
output circuit H or C) is:
0: Not to be used
1: To be used
NOTE
1 When high-resolution serial output circuit H is used,
set the setting pin SW3 inside the circuit to "Setting
B" usually.
2 This function bit can be used with the following
series and editions:
(Series 30i, 31i, 32i)
(Series 15i-B, 16i-B, 18i-B, 21i-B, 0i-B, 0i Mate-B,
Power Mate i)
Series 90B0/Q(17) and subsequent editions
(Series 0i-C, 0i Mate-C, 20i-B)
If this bit is specified, the minimum resolution
setting of the detector is assumed to be:
Encoder signal pitch/512 [µm]
If the minimum resolution (signal pitch/2048 [µm])
is necessary as the detection unit, specify:
Flexible feed gear = 4/1
3 When high-resolution serial output circuit H is used,
and the input frequency 750 kHz needs to be
supported, set the following:
- Set the setting pin SW3 to "Setting A".
- Set HP2048=1.
- Set the minimum resolution of the detector as:
Encoder signal pitch/128 [µm]
(Related report: TMS03/16E)
- 36 -
[Minimum resolution of the detector]

In the following calculation of a flexible feed gear and the number of
position pulses, the minimum detector resolution to be used is:
(Linear encoder signal pitch/512 [µm])
(Specifying the above function bit appropriately makes it unnecessary
to take the difference in the interpolation magnification among the
high-resolution serial output circuits into account. So always use 512
for calculations.)

Parameters Nos. 1977 and 1978 (Series 15i) or Nos. 2084 and 2085
(Series 30i, 16i, and so on)
Flexible feed gear (N/M)
= minimum resolution of the detector [µm] /
detection unit of controller [µm]

Parameter No. 1891 (Series 15i) or No. 2024 (Series 30i, 16i, and so
on)
= Amount of movement per motor revolution [mm] /
minimum resolution of the detector [mm]
No.1891 (Series15i), No.2024 (Series 30i, 16i, and so on)

• A linear encoder with a signal pitch of 20 µm is used.
• The linear encoder is coupled with high-resolution serial output
circuit H.
[Parameter setting]
1.
• To use high-resolution serial output circuit H, set bit 0 of
parameter No. 2274 to 1.
Minimum resolution of the detector = 20 µm/512
= 0.0390625 µm
- 37 -

Because flexible feed gear (N/M)=(20/512µm)/1µm=5/128
No.2084=5, No.2085=128
Number of position pulses = 16 mm/(20/512µm) = 409,600
409,600 = 25,600 × 16 → A = 25,600, B = 16
No.2024 = 25,600, No.2185 = 16
(c) Parameter setting for the serial output type rotary encoder
* For explanations about the rotary encoders RCN220, RCN223,

RCN723, and RCN727 made by HEIDENHAIN, see "Parameter
setting for the rotary encoders RCN220, RCN223, RCN723, and
RCN727 made by HEIDENHAIN."

In addition to the conventional settings for a separate detector (bit 1 of
parameter No. 1815 (Series15i, 30i, 16i, 18i, 21i, 20i, 0i, and Power
Mate i), bit 3 of parameter No. 1807 (Series 15i), and if needed,
FSSB), note the following parameters:

(Series 30i, 16i and so on)
(Amount of table movement [deg] per detector revolution) /
(detection unit [deg]) / 1,000,000

Parameter No. 1891 (Series 15i) or No. 2024 (Series 30i, 16i and so
on)
Number of position pulses = 12500×(motor-to-table reduction ratio)
- 38 -

• The least input increment of the controller is 1/1000 degrees.
• The amount of movement per motor revolution is 180 degrees
(reduction ratio: 1/2)
• Table-to-separate-encoder reduction ratio = 1/1
[Parameter setting]
1.
Because flexible feed gear (N/M)
=360 degrees /0.001 degrees /1,000,000 =36/100
No.2084=36, No.2085=100
Because number of position pulses = 12500 × (1/2)=6250
No.2024=6250
- 39 -
(d) Parameter setting for the rotary encoders RCN220, RCN223, RCN723, and
RCN727 made by HEIDENHAIN
(Series and editions of applicable servo software)
To use the high-resolution rotary encoders RCN220, RCN223,
RCN723, and RCN727 manufactured by HEIDENHAIN as separate
detectors, the following servo software is required:
[RCN220,223,723]
Series 90B0/T(19) and subsequent editions
[RCN727]
Series 90D0/J(10) and subsequent editions
Series 90E0/J(10) and subsequent editions
Series 90B1/B(02) and subsequent editions
Series 90B8/B(02) and subsequent editions

To specify parameters for the high-resolution rotary encoders
RCN220, RCN223, RCN723, and RCN727 (supporting FANUC serial
interface) made by HEIDENHAIN, use the following procedure.
In addition to the conventional separate detector settings (bit 1 of

parameter No. 1815 (Series 30i, 15i, 16i, 18i, 21i, 0i, and Power Mate
i), bit 3 of parameter No. 1807 (Series 15i), and, if necessary, FSSB
setting), pay attention to the following parameter settings.
[Function bit]
To use the RCN220, RCN223, RCN723, or RCN727, set the
following function bit to 1.
#7 #6 #5 #4 #3 #2 #1 #0
2688 (FS15i) RCNCLR 800PLS
2275 (FS30i, 16i)
800PLS (#0) A rotary encoder with eight million pulses per revolution is:
0: Not to be used. (To use the RCN220, leave this bit set to 0.)
1: To be used. (To use the RCN223, RCN723, or RCN727, set the
bit to 1.)
- 40 -
RCNCLR (#1) The number of revolution is:

0: Not to be cleared.
1: To be cleared. (To use the RCN220, RCN223, RCN723, or
RCN727, set the bit to 1.)
This function bit is to be set in combination with the number of data
mask digits, described below.
2807 (FS15i) Number of data mask digits

2394 (FS30i, 16i)
[Settings] 8. (To use the RCN223, RCN723, or RCN727)
5. (To use the RCN220)
The value to be set in this parameter depends on the detector. At
present, only the above detectors require clearing the speed data.
This parameter is to be set in combination with RCNCLR, described
above.
NOTE
The speed data of the RCN220, RCN223,
RCN723, or RCN727 is maintained while the power
to the separate detector interface unit is on. The
data, however, is cleared when the unit is turned
off. Since the speed data becomes undetermined
depending on where the power is turned off, it is
necessary to make a setting to clear the speed
data. In addition, for this reason, the RCN220,
RCN223, RCN723, and RCN727 cannot be used
with a linear axis.
When using the RCN220, set the parameters for the flexible feed gear
and the number of position pulses according to the setting method
described in the previous item, "Parameter setting for the serial output
type rotary encoder".
The following explains how to calculate the parameter values when
the RCN223, RCN723, or RCN727 is used.

(Series 30i, 16i, and so on)
(Amount of table movement [deg] per detector revolution) /
(detection unit [deg]) / 8,000,000
For the RCN223, RCN723, and RCN727, the number of pulses per
detector turn is assumed to be eight million for calculation.
For the RCN727, when the detection unit is set to 1/8,000,000

revolution or less, the flexible feed gear may be set to up to 8/1. (If the
flexible feed gear is set to 8/1, the detection unit is 64,000,000 pulses
per revolution.)
- 41 -

on)
Number of position pulses = 100,000×(motor-to-table reduction ratio)
[Reference counter capacity]

on)
Specify the number of feedback pulses per table turn (detection unit).
* If bit 0 of parameter No. 2688 (Series 15i) or parameter No. 2275
(Series 30i, 16i, and so on) is 0, specify the number of pulses per
table turn divided by 8 as the reference counter capacity. In this
case, eight grid points occur per table turn.

• The rotary encoder RCN223 made by HEIDENHAIN is used.
• The least input increment of the controller is 1/10,000 degrees.
• The amount of movement per motor revolution is 180 degrees
(reduction ratio: 1/2)
• Table-to-separate-encoder reduction ratio = 1/1
[Parameter setting]
1.
• To use the detector RCN223, set bit 0 of parameter No. 2275 to 1,
bit 1 of this parameter to 1, and parameter No. 2394 to 8.
Because flexible feed gear (N/M) =
(360 degrees /0.0001 degrees)/8,000,000=9/20
No.2084=9, No.2085=20
Number of position pulses = 100,000 × (1/2) = 50,000
50,000 = 12,500 × 4 → A = 12,500, B = 4
No.2024 = 12,500, No.2185 = 4
- 42 -
• Calculate the reference counter capacity.

Reference counter capacity = 360 degrees/0.0001 degrees =
3,600,000
(About speed limit)
When the RCN223, RCN723, or RCN727 is used as a separate
detector, the maximum permissible speed that can be controlled may
be 937 min-1. (*) (See Item (2) in the Appendix E.)
(*) The above maximum speed does not include hardware

limitations. For the maximum permissible speed of the detector
itself, refer to the specifications of the detector.
Setting the signal direction of the separate detector
When connecting the separate detector signal in the reverse direction,

use the following parameter:
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) RVRSE
2018 (FS30i, 16i)
RVRSE (#0) The signal direction of the separate detector is:
0: Not reversed.
1: Reversed.
(5) Reference position return when a serial type separate detector is used as
an absolute-position detector
When a serial type separate detector is used as an absolute-position
detector, the phase-Z position must be passed once before a reference
position return is performed. Then, turn the CNC off then back on to
allow reference position return.
(This description does not apply if a detector that does not require
battery backup is in use.)
When reference position return is performed, adjust the deceleration
dog so that the grid-shifted reference position is not too near the
deceleration dog.
Encoder position Position data from
the encoder Direction of reference
Reference position not grid-shifted
position return
Grid-shifted reference
Start position of reference position
position return
Reference counter
Reference position data
of the detector = 0
Reference counter capacity

Grid shift amount
Machine position
Deceleration dog
To be adjusted so that the grid-shifted reference
position is not too near the deceleration dog
- 43 -
2.1.5 Setting Servo Parameters when an Analog Input Separate

Detector Interface Unit is Used
(1) Overview
An analog input separate detector interface unit (analog SDU) can be
connected directly to an encoder having an analog output signal of 1
Vp-p. This subsection explains parameter settings to be made when
this unit is connected to a separate detector. After performing the
initialization procedure (full-closed loop) described in Subsection
2.1.3, change the setting described below according to the signal pitch
of the detector.
Configuration where analog SDU is used
Separate detector
X 000.000
Y 000.000
Z 000.000
FSSB 1Vp-p
Analog SDU

Series 90B1/C(03) and subsequent editions
(Series 0i-C,0i Mate-C)

After performing the initialization (full-closed loop) described in
Subsection 2.1.3, change the following setting according to the signal
pitch of the detector:
[Setting the flexible feed gear]

1977 (FS15i) Numerator of flexible feed gear
2084 (FS30i,16i)
1978 (FS15i) Denominator of flexible feed gear

2085 (FS30i,16i)
Set the flexible feed gear according to the following equation.
(Equation for parameter calculation)
Detector signal pitch [µm]/512
Detection unit of controller [µm]
- 44 -
[Setting the number of position pulses]

1891 (FS15i) Number of position pulses (PPLS)
2024 (FS30i,16i)
Set the number of position pulses according to the following equation:
Amount of movement per motor revolution [mm]
Number of position pulses =
Detector signal pitch [mm]/512
If the calculation result is greater than 32767, use the following

position pulse conversion coefficient (PSMPYL) to obtain the
parameter setting (PPLS).
2628 (FS15i) Position pulse conversion coefficient (PSMPYL)

2185 (FS30i,16ii)
This parameter is used when the calculation result of the number of
position pulses is greater than 32767.
Set this parameter so that the following equation is satisfied:
Number of position pulses = PPLS × PSMPYL
(→ See Supplementary 3 in Subsection 2.1.8.)

• A linear scale with a signal pitch of 20 µm is used.
[Parameter setting]
1.
Because flexible feed gear (N/M)=(20/512µm)/1µm=5/128
No.2084=5, No.2085=128
Number of position pulses = 16 mm/(0.02 mm/512)= 409,600
409,600 = 25,600 × 16 → A = 25,600, B = 16
No.2024 = 25,600, No.2185 = 16
- 45 -
2.1.6 Setting Parameters when an αiCZ Sensor is Used
(1) Overview
The αiCZ sensors are classified into two major groups according to
their application as follows:
<1> Used as a built-in detector for a synchronous built-in servo motor
(αiCZ ***A)
<2> Used as a separate detector (αiCZ ***AS)
When the differences in resolution are considered, six types of sensors
are available as indicated below.
For built-in For separate
Signal Number of pulses at
detector detector
interval setting
(A860-2162-Txxx) (A860-2164-Txxx)
αiCZ 512A αiCZ 512AS 512λ/rev 500,000pulse/rev
αiCZ 768A αiCZ 768AS 768λ/rev 750,000pulse/rev
αiCZ 1024A αiCZ 1024AS 1024λ/rev 1,000,000pulse/rev
NOTE
When αiCZ 768A/AS is used as a built-in detector
with a synchronous built-in servo motor, the sensor
can be used only for the purpose of finite rotation
(within ±1 revolution).

When the αiCZ sensor is used as a built-in detector with a
synchronous built-in servo motor ((3)-(a)), the servo software
indicated bellow is needed.
• αiCZ 512A, αiCZ 1024A ((3)-(a) For use as a detector built into
a DiS motor)
• αiCZ 768A ((3)-(a) For use as a detector built into a DiS motor)
- 46 -
• αiCZ 512AS, αiCZ 768AS, αiCZ 1024AS ((3)-(b) For use as a

separate detector)

(a) Used as the detector for a synchronous built-in servo motor)
[Setting AMR]
#7 #6 #5 #4 #3 #2 #1 #0
1806 (FS15i) 0 AMR6 AMR5 AMR4 AMR3 AMR2 AMR1 AMR0
2001 (FS30i,16i)
Set the value listed below according to the detector.
Detector AMR
Set the number of poles of the synchronous built-in servo
αiCZ 512A
motor in binary.
αiCZ 768A Set 0.
Set a value obtained by dividing the number of poles of the
αiCZ 1024A
synchronous built-in servo motor by 2 in binary.
Setting example:
When an 88-pole synchronous built-in servo motor and the αiCZ
1024A are used:
Number of poles/2 = 88/2 = 44
→ The binary representation of the above value is 00101100.
This value is set in AMR.
#7 #6 #5 #4 #3 #2 #1 #0
2608 (FS15i) DECAMR
2220 (FS30i,16i)
Set one of the following values according to the detector.
Detector DECAMR
αiCZ 512A Set 0.
αiCZ 768A Set 1.
αiCZ 1024A Set 0.
- 47 -
1705 (FS15i) AMR conversion coefficient 1

2112 (FS30i,16i)

2138 (FS30i,16i)
AMR conversion
Detector AMR conversion coefficient 2
coefficient 1
αiCZ 512A Set 0. Set 0.
αiCZ 768A Set 768. Set half the number of poles.
[Setting flexible feed gear]

1977 (FS15i) Flexible feed gear (numerator)
2084 (FS30i,16i)
1978 (FS15i) Flexible feed gear (denominator)

2085 (FS30i,16i)
Set the flexible feed gear according to the equation below.
The number of pulses per detector rotation is as follows:
Detector Flexible feed gear
Amount of movement per motor revolution [deg]/
αiCZ 512A detection unit [deg]
500,000
750,000
1,000,000

Flexible feed gear (N/M) = detection unit [deg]
Number of pulses per detector rotation
[Setting number of velocity pulses]

1876 (FS15i) Number of velocity pulses (PULCO)
2023 (FS30i,16i)
Set a value listed in the following table according to the detector used.
Detector Number of velocity pulses
αiCZ 512A 4096
αiCZ 768A 6144
αiCZ 1024A 8192
- 48 -
[Setting number of position pulses]

2024 (FS30i,16i)
Detector Number of position pulses
αiCZ 512A 6250
αiCZ 768A 9375
αiCZ 1024A 12500
[Setting reference counter capacity]

1896 (FS15i) Reference counter capacity
1821 (FS30i,16i)
Detector Reference counter capacity
Set the number of pulses per motor revolution (detection
αiCZ 512A unit) or a value obtained by dividing that number by an
integer.
Set the number of pulses per 120-degree motor revolution
αiCZ 768A (one-third revolution) (detection unit) or a value obtained
by dividing that number by an integer.
Set the number of pulses per motor revolution (detection
αiCZ 1024A unit) or a value obtained by dividing that number by an
integer.

• An 88-pole/rev, synchronous built-in servo motor is used.
• The detector used is the αiCZ512A.
• The least input increment of the controller is 1/1000 deg.
• Gear ratio 1:1
[Parameter setting]
AMR=01011000 (88 in decimal representation)
Flexible feed gear (N/M) = 360,000/500,000 = 18/25, so parameter No.
2084 = 18, and parameter No. 2085 = 25
Number of velocity pulses = 4096
Number of position pulses = 6250
Reference counter capacity = 360,000
- 49 -
(b) Used as a separate detector

After performing the initialization procedure (full-closed loop)
described in Subsection 2.1.3, change the settings described below
according to the signal pitch of the detector.
[Setting flexible feed gear]

1977 (FS15i) Flexible feed gear (numerator) (N)
2084 (FS30i,16i)
1978 (FS15i) Flexible feed gear (denominator) (M)

2085 (FS30i,16i)
Detector Flexible feed gear
αiCZ 512AS detection unit [deg]
500,000
750,000
1,000,000
[Setting number of velocity pulses]

2023 (FS30i,16i)
Set the number of velocity pulses to 8192.
[Setting number of position pulses]

2024 (FS30i,16i)
Detector Number of position pulses
αiCZ 512AS 6250 × (gear reduction ratio from the motor to table)
If the calculation result is greater than 32767, use the following

position pulse conversion coefficient (PSMPYL) to obtain the
parameter value (PPLS).
2628 (FS15i) Conversion coefficient for the number of position feedback pulses (PSMPYL)
2185 (FS30i,16i)
This parameter is used when the calculated number of position pulses
is greater than 32767.
Set this parameter so that the following equation is satisfied:
Number of position pulses = PPLS × PSMPYL
(→ See Supplementary 3 in Subsection 2.1.8.)
- 50 -
[Setting reference counter capacity]

1821 (FS30i,16i)
Detector Reference counter capacity
Set the number of pulses per revolution of the detector
αiCZ 512AS installed separately (detection unit) or a value obtained by
dividing that number by an integer.
Set the number of pulses per 120-degree revolution
(one-third revolution) of the detector installed separately
αiCZ 768AS
(detection unit) or a value obtained by dividing that
number by an integer.
Set the number of pulses per revolution of the detector
αiCZ 1024AS installed separately (detection unit) or a value obtained by
dividing that number by an integer.

• The detector used is the αiCZ1024AS
• The least input increment of the controller is 1/1000 deg.
• Gear ratio 1:1
[Parameter setting]
Flexible feed gear (N/M) = 360,000/1,000,000＝9/25,
so parameter No. 2084 = 9, and parameter No. 2085 = 25
Number of position pulses = 12500
Reference counter capacity = 360,000
- 51 -
2.1.7 Setting Parameters When an Acceleration Sensor or

Temperature Detection Circuit Is Used
(1) Overview
The flow indicated below is used to make a connection and setting for
using an acceleration sensor (αiGS0.1-3D) or temperature detection
circuit.
Connect acceleration sensor or temperature See (3)-(a), "Connection of an acceleration

detection circuit by using separate detector sensor or temperature detection circuit".
interface unit
Set parameters for using acceleration See (3)-(b),"Setting for enabling an

sensor or temperature detection circuit acceleration sensor or temperature detection
circuit".
Check whether acceleration sensor or See (3)-(c), "Checking the connection of an

temperature detection circuit is set correctly acceleration sensor or temperature
detection circuit".
• Acceleration sensor
Series 90D0/P(16) and subsequent editions
Series 90E0/P(16) and subsequent editions
(Series 16i-B,18i-B,21i-B,0i-B,0i Mate-B,Power Mate i)
Series 90B1/I(09) and subsequent editions
(Series 0i-C, 0i Mate-C)
• Temperature detection circuit

Series 90B1/K(11) and subsequent editions
(Series 0i-C, 0i Mate-C)
- 52 -
(3) Setting method

(a) Connection of an acceleration sensor or temperature detection circuit
An acceleration sensor or temperature detection circuit is connected to
a separate detector interface unit. From one separate detector interface
unit, only one data item can be read per axis. So, when an additional
acceleration sensor or temperature detection circuit is to be used in a
full-closed system, one more separate detector interface unit is
required in addition to the separate detector interface unit used for a
separate position detector.
・ When an acceleration sensor or temperature detection circuit is to
be added to an axis of a semi-closed system
Add a separate detector interface unit for an acceleration sensor
or temperature detection circuit.
Semi-closed To be newly added
Separate detector
interface unit
FSSB FSSB
CNC Servo amplifier

Acceleration sensor
Temperature
detection circuit
・ When an acceleration sensor or temperature detection circuit is to

be added to an axis of a full-closed system
Add a separate detector interface unit for an acceleration sensor
or temperature detection circuit
Full-closed To be newly added
Separate detector
interface unit
Separate detector
interface unit
FSSB FSSB FSSB
CNC Servo amplifier

Acceleration sensor
Separate position detector Temperature detection
circuit
NOTE
1 When an acceleration sensor or temperature
detection circuit is added to an axis of a full-closed
system, the acceleration sensor may not be
connected to a free connector of the separate
detector interface unit to which a separate position
detector is connected.
2 For the FSSB setting, refer to the parameter
manual of the CNC.
- 53 -
(b) Setting for enabling an acceleration sensor or temperature detection circuit

<1> Setting for enabling an acceleration sensor
The setting for enabling an acceleration sensor is described below.
An acceleration sensor can detect acceleration in one of three
directions.
Select and set one of the three function bits below according to the
direction of acceleration to be used.
#7 #6 #5 #4 #3 #2 #1 #0
2277 (FS30i,16i) ACC1ON ACC2ON ACC3ON
ACC1ON(#7) Specify whether acceleration feedback in the first direction is used or
not. (Power-off parameter)
0: Not used
1: Used
ACC2ON(#6) Specify whether acceleration feedback in the second direction is used
or not. (Power-off parameter)
0: Not used
1: Used
ACC3ON(#5) Specify whether acceleration feedback in the third direction is used or
not. (Power-off parameter)
0: Not used
1: Used
3rd direction (+)

2nd direction (+)
1st direction (+)

* When the machine is accelerated in the arrow direction, positive
acceleration is detected.
* The output direction of acceleration data can be inverted. (This
function is described later.)
NOTE
Acceleration feedback in one direction can be used
per axis. Do not set two directions or more per axis.
Set the function bit below according to the ordinal number, counted
from the CNC, of the separate detector interface unit to which an
acceleration sensor is connected.
- 54 -
#7 #6 #5 #4 #3 #2 #1 #0
2278 (FS30i,16i) PM2ACC
PM2ACC(#4) (Power-off parameter)
0: Acceleration sensor data is read from the first or third separate
detector interface unit counted from the CNC, or no acceleration
sensor is used.
1: Acceleration sensor data is read from the second or fourth
separate detector interface unit counted from the CNC.
NOTE
1 Both of the first and third separate detector
interface units cannot be used with one axis.
Similarly, both of the second and fourth separate
detector interface units cannot be used with one
axis.
2 The third and fourth separate detector interface
units can be used only when two FSSB paths are
used with the Series 30i/31i/32i.
Set a detection unit in units of 1 nm.

2263 (FS30i,16i) Detection unit setting
[Setting unit] In units of 1 nm
Detection unit 10µm 1µm 0.1µm 0.01µm 0.001µm 0.05µm

Setting 10000 1000 100 10 1 50
To adjust the sign of acceleration feedback, observe position feedback

(POSF) and acceleration feedback (ACC) with SERVO GUIDE at
rapid traverse acceleration/deceleration time.
Set the sign bit ACCNEG for acceleration feedback below so that the
sign of the second-order differential of position feedback (POSF
indicated by Diff2(AT) operation) equals the sign of acceleration
feedback (ACC).
NOTE
The observation of ACC is supported by SERVO
GUIDE version 3.20 or later.
- 55 -
#7 #6 #5 #4 #3 #2 #1 #0
2277 (FS30i,16i) ACCNEG
ACCNEG(#4) The sign of acceleration feedback is:
0 : Not inverted
1 : Inverted
Acceleration
2nd-order feedback
differential of ドバク
position feedback
Velocity
2
Unit: m/s
<2> Setting for enabling a temperature detection circuit
The setting for enabling a temperature detection circuit is described

below.
Set the function bits below according to the ordinal number, counted
from the CNC, of the separate detector interface unit to which a
temperature detection circuit is connected.
#7 #6 #5 #4 #3 #2 #1 #0
2691 (FS15i) PM2TP PM1TP
2278 (FS30i,16i)
PM1TP(#0) With the first or third separate detector interface unit, a temperature
detection circuit is:
0 : Not used (Power-off parameter)
1 : Used
PM2TP(#1) With the second or fourth separate detector interface unit, a
temperature detection circuit is:
0 : Not used (Power-off parameter)
1 : Used
NOTE
axis.
- 56 -
(c) Checking the connection of an acceleration sensor or temperature detection

circuit
On diagnosis screen No. 350#2/#1 or No. 351#2/#1, check whether an
acceleration sensor or temperature detection circuit is connected
correctly.
#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 350 PM1TMP PM1ACC
PM1ACC(#1) With the first or third separate detector interface unit, an acceleration
sensor is:
1 : Connected
0 : Not connected
PM1TMP(#2) With the first or third separate detector interface unit, a temperature
1 : Connected
0 : Not connected
NOTE
axis.
#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 351 PM2TMP PM2ACC
PM2ACC(#1) With the second or fourth separate detector interface unit, an
acceleration sensor is:
1 : Connected
0 : Not connected
PM2TMP(#2) With the second or fourth separate detector interface unit, a
1 : Connected
0 : Not connected
NOTE
axis.
- 57 -
(4) Example of setting an acceleration sensor or temperature detection circuit

An example of adding an acceleration sensor (X-axis, Y-axis, Z-axis)
and temperature detection circuit (X-axis) to a system with a
semi-closed axis (X-axis) and two full-closed axes (Y-axis, Z-axis) is
described below.
<Connection>
CNC⇔X-axis amplifier⇔Y-axis amplifier⇔Z-axis amplifier
⇔ Separate detector interface unit
(Separate detector interface units for the Y-axis and Z-axis
are connected to the first and second connectors.
A temperature detection circuit for the X-axis is connected
to the third connector.)
⇔ Separate detector interface unit
(An acceleration sensor is connected to the first connector.)
CNC Servo amplifier 1st separate detector Position detector (for Y-axis)
(X-/Y-/Z-axis) interface unit
Position detector (for Z-axis)
FSSB
Temperature detection circuit
(for X-axis)
Acceleration sensor (for X-/Y-/Z-axis)
2nd separate detector

interface unit
<Setting>
Setting
Parameter No. Description
X-axis Y-axis Z-axis
Bit 1 of No. 1815 Enables a separate position detector.(*1) 0 1 1
Enables an acceleration sensor (including the setting of
Bits 7, 6, 5 of No. 2277 100 010 001
direction).
Sets the ordinal number of the separate detector interface
Bit 4 of No. 2278 1 1 1
unit to which an acceleration sensor is connected.(*2)
Sets the ordinal number of the separate detector interface
Bits 1, 2 of No. 2278 01 00 00
unit to which a temperature detection circuit is connected.(*3)
*1 Bit 1 of No. 1815 =
1: Full-closed
0: Semi-closed
*2 Bit 4 of No. 2278 =
1: An acceleration sensor is used with the second or
fourth separate etector interface unit.
0: An acceleration sensor is used with the first or third
separate detector interface unit.
*3 Bits 1, 0 of No. 2278 =
0,0: A temperature detection circuit is unused.
0,1: A temperature detection circuit is used with the first
or third separate detector interface unit.
1,0: A temperature detection circuit is used with the
second or fourth separate detector interface unit.
- 58 -
NOTE
axis.
(5) Alarms
Alarms related to an acceleration sensor
When an error is detected with an acceleration sensor, the following
alarm is issued and the axis with which the alarm is issued is brought
to a feed-hold stop:
DS651: Acceleration sensor error
When the CNC software does not support the display of the alarm
above, the following alarm is issued and a dynamic brake stop occurs:
SV385: Serial data error (separate) or
SV447: Hardware disconnection alarm (separate)
If a separate detector and acceleration sensor are used at the same time,
diagnosis screen No. 350#5 can be used to identify with which
detector the alarm has been issued.
#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 350 ALMACC
ALMACC(#5) 0 : An alarm is issued with a separate detector.
1 : An alarm is issued with an acceleration sensor.
Alarms related to a temperature detection circuit

When an error is detected with a temperature detection circuit, the
following alarm is issued and a dynamic brake stop occurs:
SV652: Temperature sensor error
When the CNC software does not support the display of the alarm
above, the following alarm is issued and a dynamic brake stop occurs:
SV385: Serial data error (separate) or
SV447: Hardware disconnection alarm (separate)
If a separate detector and acceleration sensor are used at the same
time, diagnosis screen No. 350#6 can be used to identify with which
detector the alarm has been issued.
- 59 -
#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 350 ALMTMP
ALMTMP(#6) 0 : An alarm is issued with a separate detector.
1 : An alarm is issued with a temperature detection circuit.
NOTE
The series and editions of CNC software that support the display of acceleration
sensor and temperature sensor alarms are indicated below (as of August 2007).
FS30i-A : G002,G012,G022,G032/32.0 and subsequent editions
: G003,G013,G023,G033/15.0 and subsequent editions
FS31i-A5 : G121,G131/32.0 and subsequent editions
: G123,G133/15.0 and subsequent editions
FS31i-A : G101,G111/32.0 and subsequent editions
FS32i-A : G201/32.0 and subsequent editions
: G203/15.0 and subsequent editions
FS16i/18i/21i-MB : B0K1,BDK1,DDK1/10 and subsequent editions
FS16i/18i/21i-TB : B1K1,BEK1,DEK1/10 and subsequent editions
FS18i-MB5 : BDK5/10 and subsequent editions
- 60 -
2.1.8 Actions for Illegal Servo Parameter Setting Alarms
(1) Overview
When a setting value is beyond an allowable range, or when an
overflow occurs during internal calculation, an invalid parameter
setting alarm is issued.
This section explains the procedure to output information to identify
the location and the cause of an illegal servo parameter setting alarm.

Series90D0/A(01) and subsequent editions
Series90E0/A(01) and subsequent editions
Series9096/A(01) and subsequent editions
Series90B0/A(01) and subsequent editions
(3) Illegal servo parameter setting alarms that can be displayed in parameter
error detail display
Illegal servo parameter setting alarms detected by the servo software
can be displayed. Alarms detected by the system software cannot be
displayed here.
To check whether the servo software detects an alarm, check the
following:
#7 #6 #5 #4 #3 #2 #1 #0
Alarm 4 on the servo screen PRM
0: Alarm detected by the system software (With Series including

16i, identification is possible using diagnosis No.280.)
1: Alarm detected by the servo software (See the descriptions of
detailed display provided later.)
- 61 -
#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 280 AXS DIR PLS PLC MOT
MOT(#0) 1: As the motor number in parameter No. 2020, a value not within
the specifiable range is set.
The table given below lists the valid motor ID numbers for each
series.
If a number beyond the indicated range is set, an illegal servo
parameter setting alarm is issued.
(In this case, keep PRM = 0.)
Servo software series/edition Motor ID No.
Series 9096/A(01) and subsequent editions 1 to 250
Series 90B0/H(08) and subsequent editions 1 to 350
Series 90B1/B(02) and subsequent editions 1 to 550
Series 90B5,90B6/B(02) and subsequent editions 1 to 550
Series 90D0,90E0/B(02) and subsequent editions 1 to 550
PLC(#2) 1: As the number of velocity feedback pulses per motor revolution

in parameter No. 2023, an invalid value such as a number equal
to or less than 0 is set.
PLS(#3) 1: As the number of position feedback pulses per motor revolution

in parameter No. 2024, an invalid value such as a number equal
to or less than 0 is set.
DIR(#4) 1: As the motor rotation direction in parameter No. 2022, a correct

value (111 or -111) is not set.
AXS(#6) 1: Parameter No. 1023 (servo axis number) is set incorrectly. A

duplicate servo axis number is set, or a value exceeding the
number of controlled axes of the axis control card is set.
- 62 -
(4) Method
When an illegal servo parameter setting alarm detected by the servo
software is issued, analyze the cause of the alarm by following the
procedure explained below.
* When more than one alarm is issued, one of the causes of these
alarms is displayed. Analyze the alarms one by one.
Procedure for displaying detail information about an illegal servo parameter setting
alarm
(For the Series 15i)

On the servo alarm screen, an item indicating parameter error
details is located in the lower left side. Check the number
indicated here.
(For the Series 30i, 16i and so on)

On the diagnosis screen, search for No. 352. Check the number
written in No. 352.
Analyzing illegal servo parameter setting alarms in detail
The detail alarm data basically consists of three to five digits as

shown:
0 0 4 3 4
Location where an Cause of the alarm

alarm was caused
Upper four digits:
Indicate the location where an alarm was caused.
Table 2.1.8 lists the displayed numbers and corresponding
parameter numbers.
*1 Basically, the low-order three digits of the 4-digit
parameter number of the Series 16i indicate the
location where an alarm was caused. (When an alarm
is due to more than one parameter, these digits and
parameter numbers do not sometimes match.)
*2 When the digits are displayed on the servo alarm
screen (Series 15i) or diagnosis screen (Series 30i, 16i,
and so on), 0s in high-order digits are not displayed.
Lowest digit:
Indicates the cause of an alarm.
The displayed numbers and their meanings are explained
below:
2: The set parameter is invalid. The corresponding
function does not operate.
3: The parameter value is beyond the setting range.
Alternatively, the parameter is not set.
4 to 9: An overflow occurred during internal calculation.
- 63 -
Table 2.1.8 Detail analysis of illegal servo parameter setting alarms

Parameter No.
Alarm Parameter No.
Series 30i, 16i, Cause Action
detail No. Series 15i
and so on
Parameter settings related to Change the parameter settings so
83 - 2008 learning control are illegal that they fall in the applicable
→ See Supplementary 1. range.
When initialization bit 0 is set to 1,
Correct the number of velocity
233 1876 2023 the number of velocity pulses
pulses so that it is within 13100.
exceeds 13100.
Set 512 or a greater number as the
number of velocity pulses, or
When a DD motor is used, a value
disable the DD motor.
234 1876 2023 smaller than 512 is set as the
No.2300#0=0 (Series 30i, 16i, and
number of velocity pulses.
so on)
No.2713#0=0 (Series15i)
When initialization bit 0 is set to 1, Correct the number of position
243 1891 2024 the number of position pulses pulses so that it is within 13100.
exceeds 13100. → See Supplementary 3.
434 The internal value of the velocity Decrease the value of the velocity
1855 2043
435 loop integral gain overflowed. loop integral gain parameter.
Use the function for changing the
internal format of the velocity loop
443
The internal value of the velocity proportional gain.
444 1856 2044
loop proportional gain overflowed. Alternatively, decrease the
445
parameter setting.
→ See Supplementary 4.
474 The internal value of the observer Correct the setting to
1859 2047
475 parameter (POA1) overflowed. (−1) × (desired value)/10.
The internal value of a parameter Decrease the setting to the extent
534
1865 2053 related to dead zone compensation that the illegal servo parameter
535
overflowed. setting alarm is not caused.
The internal value of a parameter Decrease the setting to the extent
544
1866 2054 related to dead zone compensation that the illegal servo parameter
545
overflowed. setting alarm is not caused.
686 Use the position gain expansion
The internal value of the
687 1961 2068 function.
feed-forward coefficient overflowed.
688 → See Supplementary 5.
694
695 The internal value of the velocity Decrease the velocity feed-forward
1962 2069
696 feed-forward coefficient overflowed. coefficient.
699
754 The setting for this parameter has This parameter is not used at
1968 2075
755 overflowed. present. Set 0.
764 The setting for this parameter has This parameter is not used at
1969 2076
765 overflowed. present. Set 0.
Set a positive value as the flexible
A positive value is not set as the feed gear numerator.
flexible feed gear numerator. Alternatively, correct the parameter
843 1977 2084 Alternatively, the numerator of the so that the numerator of the feed
feed gear is greater than the gear is less than or equal to the
denominator. denominator. (For other than
parallel type separate detectors)
A positive value is not set as the Set a positive value as the flexible
853 1978 2085
flexible feed gear denominator. feed gear denominator.
- 64 -
Parameter No.
Alarm Parameter No.
and so on
For an axis with a serial type
For an axis with a serial type separate detector, the upper limit
separate detector, a value of the machine velocity feedback
883 1981 2088
exceeding 100 is set as the machine coefficient is 100. Correct the
velocity feedback coefficient. coefficient so that it does not
exceed 100.
Decrease the machine velocity
884 The internal value of the machine feedback coefficient.
885 1981 2088 velocity feedback coefficient Alternatively, use the
886 overflowed. vibration-damping control function
that has an equivalent effect.
Use the "position gain precision
926
The internal value of the look-ahead optimization function" or the
927 1985 2092
feed-forward coefficient overflowed. "position gain increment function".
928
If nano interpolation is not used,
this alarm can be avoided by the
1988 2095 The internally set value of the
following setting:
953 1763 2140 feed-forward timing adjustment
No.2224#5=1 (Series 30i, 16i, and
2808 2395 coefficient is ±12800 or over.
so on)
No.2612#4=1 (Series15i)
Disable the N pulse suppression
function.
No.2003#4=0 (Series 30i, 16i, and
994
The internal value for N pulse so on)
995 1992 2099
suppression overflowed. No.1808#4=0 (Series15i )
996
Alternatively, decrease the
parameter setting so that no
overflow will occur.
There is a difference in retract
distance under unexpected
Set the same value for position
1033 1996 2103 disturbance torque between position
tandem synchronous axes.
tandem synchronous axes (if the
same-axis retract function is in use).
Although a linear motor is used, the
Set the AMR conversion
1123 1705 2112 AMR conversion coefficient
coefficient.
parameter is not input.
1729 2118 The dual position feedback
Specify the dual position feedback
1182 1971 2078 conversion coefficient has not been
conversion coefficient.
1972 2079 specified.
When a small value is set as the
Decrease the value in this
1284 number of velocity pulses, the
1736 2128 parameter to the extent that the
1285 internal value of a parameter related
alarm is not caused.
to current control overflows.
When a large value is set as the When the value set in this
1294 number of velocity pulses, the parameter is resolved to the form a
1752 2129
1295 internal value of a parameter related × 256 + b, set a smaller value in a
to current control overflows. again.
- 65 -
Parameter No.
Alarm Parameter No.
and so on
Keep the setting of this parameter
within ±45. Alternatively, set bit 0
of parameter No. 2683 (for the
Series 15i) or bit 0 of parameter
The AMR offset value of a linear
1393 1762 2139 No. 2270 (for the Series 30i, 16i,
motor exceeds ±45.
and so on) to 1 to increase the
setting range of the AMR offset,
and then specify the parameter
anywhere within ±60.
1446 Use the position gain expansion
Feed-forward coefficient for cutting
1447 1767 2144 function.
overflowed.
1448 → See Supplementary 5.
1454
1455 Velocity feed-forward coefficient for Decrease the velocity feed-forward
1768 2145
1456 cutting overflowed. coefficient.
1459
Only 6 or less can be specified in
A value greater than 6 is specified in
1493 1772 2149 this parameter. Change the setting
this parameter.
to 6 or below 6.
A value equal to or greater than 10 is
1503 1773 2150 Set a value less than 10.
set.
Bit 6 of No. 2212 or bit 6 of No. 2213 Set bit 6 of No. 2212 or bit 6 of No.
is set to 1, and No. 2621=0 is set. 2213 to 0. (Series 30i, 16i, and so
(Series 30i, 16i, and so on) on)
1786 2621 2178
Bit 6 of No. 2600 or bit 6 of No. 2601 Set bit 6 of No. 2600 or bit 6 of No.
is set to 1, and No. 2178=0 is set. 2601 to 0. (Series15i)
(Series15i )
A negative value or a value greater
Set a positive value less than the
than the setting of parameter No.
setting of parameter No. 1821
1793 2622 2179 1821 (Series 30i, 16i, and so on) or
(Series 30i, 16i, and so on) or
parameter No. 1896 (Series 15i) is
parameter No. 1896 (Series 15i).
set.
A negative value or a value greater
Set a positive value less than the
than the setting of parameter No.
setting of parameter No. 2023
1853 2628 2185 2023 (Series 30i, 16i, and so on) or
(Series 30i, 16i, and so on) or
parameter No. 1876 (Series 15i) is
parameter No. 1876 (Series 15i).
set.
If pole detection is enabled (bit 7 of
No. 2213=1 (Series 30i, 16i, etc.)/bit
7 of No. 2601=1 (Series 15i)) and a
non-binary detector is enabled (bit 0
of No. 2220=1 (Series 30i, 16i,
etc.)/bit 0 of No. 2608=1 (Series
15i)), an illegal servo parameter Set the AMR conversion
2203 2608#0 2220#0
setting alarm is issued when any of coefficients correctly.
the following is set:
- AMR conversion coefficient 1 ≤ 0
- AMR conversion coefficient 2 ≤ 0
- AMR conversion coefficient 2 > 512
(The settable range is 1 (2 poles) to
512 (1024 poles).)
- 66 -
Parameter No.
Alarm Parameter No.
and so on
This alarm is issued when a setting is
made to neglect the invalid setting of
the parameter for the feed-forward
timing adjustment function (bit 5 of
2243 2612#5 2224#5 Use either one.
No. 2612=1 (Series 15i)/bit 5 of No.
2224=1 (Series 30i, 16i, etc.)) and a
command for nano interpolation is
issued.
When the lifting function against Take one of the following actions:
gravity is enabled (bit 7 of No. 1) Set a value in parameter No.
2298=1) or the post-servo-off travel 2263.
distance monitor function is enabled 2) Disable the lifting function
(bit 5 of No. 2278=1), the function for against gravity and the
2632 - 2263 enabling the CNC software to post post-servo-off travel distance
the detection unit to the servo monitor function.
software is not supported and the 3) Use CNC software that
setting of the detection unit (No. supports the function for
2263) is disabled. enabling the detection unit to be
(Series 30i only) posted to the servo software.
Set HRV3. Alternatively, replace
PDM is used but HRV3 is not set.
the hardware (servo amplifier/SDU)
Alternatively, the hardware
2712 1707#0 2013#0 connected via an FSSB cable to
connected to the CNC does not
PDM with hardware that supports
support HRV3.
HRV3.
Set the following parameter to 0:
The PDM is used, but the HRV3 No.2271#0 (Series 30i, 16i, and so
2713 1707#0 2013#0
function bit is off. on)
No.2684#0 (Series15i)
When the first SDU unit is not used
(bit 6 of No. 1905=0), a setting is
1905#6 Check the FSSB setting (bit 6 of
made to connect a detector
2780 - 2277#5,6,7 No. 1905) or the detector setting
(acceleration sensor, temperature
2278#0,2,4 (bits 0, 2, and 4 of No. 2278).
detection circuit, or analog check
interface unit) to the first SDU unit.
When the second SDU unit is not
used (bit 7 of No. 1905=0), a setting
1905#7 is made to connect a detector Check the FSSB setting (bit 7 of
2781 - 2277#5,6,7 (acceleration sensor, temperature No. 1905) or the detector setting
2278#1,3,4 detection circuit, or analog check (bits 1, 3, and 4 of No. 2278).
interface unit) to the second SDU
unit.
Any of the following settings is made:
・ For use with the first SDU unit,
both of an acceleration sensor and
temperature detection circuit are
1905#6 enabled. Check the settings of the
2782 - 2277#5,6,7 ・ Settings are made to use the first acceleration sensor and
2278#0,4 SDU unit (bit 6 of No. 1905=1), temperature detection circuit.
disable an acceleration sensor (bits
5, 6, 7 of No. 2277=0,0,0), and read
acceleration data from the second
unit (bit 1 of No. 2278=1).
- 67 -
Parameter No.
Alarm Parameter No.
and so on
Any of the following settings is made:
- For use with the second SDU unit,
both of an acceleration sensor and
temperature detection circuit are
enabled.
1905#7 Check the settings of the
- Settings are made to use the
2783 - 2277#5,6,7 acceleration sensor and
second SDU unit (bit 7 of No.
2278#1,4 temperature detection circuit.
1905=1), disable an acceleration
sensor (bits 5, 6, 7 of No.
2277=0,0,0), and read acceleration
data from the second unit (bit 1 of
No. 2278=1).
At the time of full-closed system
1815#1 setting, a detector other than a
2784 - 2277#5,6,7 separate position detector is Modify the setting of the detector.
2278#0,1,4 connected (with the first/second SDU
unit).
1815#1
setting, a detector other than a
2785 - 2277#5,6,7 Modify the setting of the detector.
separate position detector is
2278#0,4
connected (with the first SDU unit).
1815#1 setting, a detector other than a
2786 - 2277#5,6,7 separate position detector is Modify the setting of the detector.
2278#1,4 connected (with the second SDU
unit).
Only one temperature detection
circuit can be connected. Modify
A setting is made to connect two
2787 - 2278#0,#1 the setting so that data is read from
temperature detection circuits.
one of the first and second SDU
units.
1815#1 Only one temperature detection
1905#6,7 circuit can be connected. Modify
A setting is made to connect two
2788 - 2277#5,6,7 the setting so that data is read from
temperature detection circuits.
2278#4 one of the first and second SDU
2278#0,1 units.
Replace the αiCZ detection circuit
and linear motor position detection
circuit with those circuits that
The αiCZ detection circuit and support overheat signal connection.
linear motor position detection circuit Alternatively, modify the setting so
3002 2713#3,#7 2300#3,#7
do not support overheat signal that the overheat signal is read
connection. from a DI signal.
Bit 3 of No. 2300=0 (Series 30i,
16i, etc.)
Bit 3 of No. 2713=0 (Series 15i)
- 68 -
Parameter No.
Alarm Parameter No.
and so on
• When bit 2 of No. 2301=1 • When bit 2 of No. 2301=1
Hardware (PS, SV) that does not Set bit 2 of No. 2301 to 0.
support DC link voltage
information output is connected,
3012 2714#2,#7 2301#2,#7 but bit 2 of No. 2301 is set to 1.
• When bit 7 of No. 2301=1 • When bit 7 of No. 2301=1
The CNC software does not Use CNC software that supports
support the torque control setting the function. (→ See
range extension function. Supplementary 6.)
3553 The value 4 or a smaller number is Set the value 5 or a greater
2768 2355
3603 set. number.
Set the value 96 or a greater
1706 2113 number. Alternatively, if no
2773 2360 The value 95 or smaller number is resonance elimination filter is used,
3603
2776 2363 set. set all of the center frequency,
2779 2366 band width, and dumping value to
0.
3603 The value 4 or a smaller number is Set the value 5 or a greater
2779 2366
3663 set. number.
Set the value 0 or a greater
4553 - 2455 A negative value is set.
number.
4563 - 2456 A value not within 0 to 12 is set. Set a value within 0 to 12.
A positive value is not set in the
Set a positive value in this
8213 1896 1821 reference counter capacity
parameter.
parameter.
・ Set a value other than 0 (when
setting = 0).
・ Use the function for automatic
8254 A position gain of 0 is set, or the
format change for position gain
8255 1825 1825 internal position gain value has
or the function for expanding the
8256 overflowed.
position gain setting range
(when setting ≠ 0).
1815#1 Set a separate detector interface
9053 － setting, no separate detector
1905#7,#6 unit.
interface unit is set.
Disable feedback mismatch
10010 The internal value of the parameter detection.
10016 1740#0 2200#0 related to feedback mismatch No.2200#0=1 (Series 30i, 16i, and
10019 detection has overflowed. so on)
No.1740#0=1 (Series15i)
When servo software Series 90B0
is used, change the software
An overflow occurred in internal
10024 edition to edition D(04) or a later
calculation on the separate detector
10025 edition. (For series other than
serial feedback extrapolation level.
90B0, the software edition need not
be changed.)
Illegal control cycle setting
This error occurs if automatic Correct this parameter related to
10033 1809 2004
modification is carried out for the interrupt cycle setting.
control cycle.
- 69 -
Parameter No.
Alarm Parameter No.
and so on
When the linear motor is used, the
When a linear motor is used, the
10053 1960#0 2018#0 scale reverse connection bit
scale reverse connection bit is set.
cannot be used.
When you use the current amplifier
continuously, set the function bit
shown to the left to 0.
The amplifier used does not support
10062 1749#4 2209#4 When using the HC alarm
the HC alarm prevention function.
prevention function, use an
appropriate amplifier that supports
the function.
The customer's board function and
The customer's board function and
10072 1951#6 2007#6 the FAD function cannot be used
FAD were specified at the same time.
together. Turn off one of them.
Change the control cycle setting to
This alarm is issued when an invalid
HRV1, HRV2, HRV3 or HRV4.
control cycle is set.
Set the same control cycle for axes
Different control cycles are set within
controlled by one servo CPU.
one servo CPU.
1809 2004
10092 Replace the detector with a
1707#0 2013#0 When HRV4 is enabled, a detector
10093 detector supporting HRV4.
1708#0 2014#0 that does not support HRV4 is used.
Alternatively, disable HRV4.
(Series 30i only)
Replace the servo amplifier with a
When HRV4 is enabled, a servo
servo amplifier supporting HRV4.
amplifier that does not support HRV4
Alternatively, disable HRV4.
is connected. (Series 30i only)
The Series 30i does not allow
1809 2004 HRV1 setting. Set HRV2, HRV3 or
10103 HRV1 is set. (Series 30i only)
1707#0 2013#0 HRV4.
Alarm for setting the current control
cycle 250µs.
1809 2004 Set the control cycle correctly.
10103 If a current control cycle of 250 µs is
1707#0 2013#0 → See Supplementary 2.
set, this alarm is issued when HRV3
is specified.
An axis for which HRV3 is specified
Current cycle mismatch alarm.
exists on the same optical cable.
This alarm is issued if the specified
10113 1707#0 2013#0 Review the placement of the
current cycle does not match the
amplifier, or disable HRV3.
actual setting.
- 70 -
Parameter No.
Alarm Parameter No.
and so on
Alarm for indicating the disability of Eliminate the cause of the disability
HRV3 setting. in setting the other axis.
10123 1707#0 2013#0 This alarm is issued when the axis Alternatively, cancel the HRV3
supports HRV3 but the other axis of setting.
the pair does not support HRV3. → See Supplementary 2.
When HRV4 is set, this alarm is
issued if any of the following
conditions is met. (Series 30i only)
- Servo software not supporting
HRV4 is used. Eliminate the causes listed on the
1707#0 2013#0 - The same FSSB system includes left. Alternatively, cancel the HRV4
10133
1708#0 2014#0 axes with HRV4 setting and axes setting.
with HRV2 or HRV3 setting. → See Supplementary 2.
- The limitation in the number of axes
is not observed.
(In HRV4 control, one axis/DSP is
set.)
HRV3 or HRV4 is unusable for the
This alarm is issued when HRV3 or
1707#0 2013#0 axis on which the alarm was
10133 HRV4 is set, but the amplifier does
1708#0 2014#0 issued.
not support these control types.
The ID of the detector connected to Check the detector-related
2690#5,6,7 2277#5,6,7
10202 the first SDU unit differs from the parameter or the state of detector
2691#0,2,4 2278#0,2,4
parameter setting. connection.
The ID of the detector connected to Check the detector-related
2690#5,6,7 2277#5,6,7
10212 the second SDU unit differs from the parameter or the state of detector
2691#1,3,4 2278#1,3,4
parameter setting. connection.
* The alarms indicated by "(Series 30i only)" may be issued only

when servo software Series 90D0 or 90E0 is used. When other
servo software series are used, these alarms are not issued.
- 71 -
Supplementary 1: Details of illegal settings of learning control parameters

For the Series 16i and so on, reset parameter No. 2115 to 0, and set
For the Series 30i and so on, reset parameter No. 2115 to 0, and set
Then change the value of diagnosis information (DGN) No. 353 to
binary form. If a resulting binary bit is 1, its bit position indicates the
detail cause. (For the Series 15i, no learning control is available.)
When using the Series 30i and so forth, see the alarm details on the
dedicated screen for part machining learning control and rigid tapping
learning control.
Bit position Cause

The band stop filter setting (No. 2244) is out of the valid
B3
range. No. 2512 is used with the Series 30i and so forth.
The profile number setting (No. 2233) is out of the valid
B4
range. No. 2511 is used with the Series 30i and so forth.
The command data cycle setting (Nos. 2243, 2236, 2238,
2240, and 2266) is out of the valid range.
B5
Nos. 2517, 2519, 2521, 2523, and 2525 are used with the
Series 30i and so forth.
The total of the profiles (No. 2264) is out of the valid range.
B6
No. 2510 is used with the Series 30i and so forth.
B7 G05 was started during memory clear processing.
The profile number (No. 2233 (No. 2510 for the Series 30i
B8 and so forth)) was 0 when the total of profiles (No. 2264
(No. 2511 for the Series 30i and so forth)) is nonzero.
An automatically set value for thinning-out shift was out of
B9
the valid range because of a long command data cycle.
- 72 -
Supplementary 2: Control cycle setting

There are four different types of control cycle setting (HRV1, HRV2,
HRV3 and HRV4). Their settings are explained below.
For Series 15i

HRV1: No1809=0X000110
HRV2: No1809=0X000011, No1707#0=0
HRV3: No1809=0X000011, No1707#0=1
For Series 16i and so on

HRV1: No2004=0X000110
HRV2: No2004=0X000011, No2013#0=0
HRV3: No2004=0X000011, No2013#0=1
For Series 30i and so on

HRV2: No2004=0X000011, No2013#0=0, No2014#0=0
HRV3: No2004=0X000011, No2013#0=1, No2014#0=0
HRV4: No2004=0X000011, No2013#0=0, No2014#0=1
When an invalid value is set in control cycle related parameters, the

following alarm messages are indicated on the CNC:
Alarm detail No. Alarm number Message

10092
456 Invalid current control cycle setting
10093
10103 457 Invalid High-speed HRV setting
10113 458 Invalid current control cycle setting
10123 459 High-speed HRV setting not allowed
High-speed HRV setting not allowed
10133 468
(amplifier)
Supplementary 3: Setting the number of position pulses

If the resolution of the separate detector is high and the number of
position feedback pulses becomes greater than 32767, take the
following measure.
(a) For other than servo software Series 9096

Use "position feedback pulse conversion coefficient" to make settings.
Number of position feedback pulses = A × B
Select B so that A is within 32767.
A: Number of position feedback pulses set in the parameter (less
than or equal to 32767)
B: Conversion coefficient for the number of position feedback
pulses
1891 (FS15i) Number of position feedback pulses

2024 (FS30i, 16i)
- 73 -
2628 (FS15i) Conversion coefficient for the number of position feedback pulses
2185 (FS30i, 16i)
(Example of setting)
If the linear scale used has a minimum resolution of 0.1 µm and the
distance to move per motor turn is 16 mm
Set A and B, respectively, to 10000 and 16, because:
Ns = distance to move per motor turn (mm)/detector minimum
resolution (mm) = 16 mm/0.0001 mm = 160000(>32767) = 10000×16
NOTE
If the detector on the motor is an αi Pulsecoder
(number of velocity pulses = 8192), select a value
raised to the second power (2, 4, 8, ...) as the
conversion coefficient as much as possible (so the
position gain used within the software becomes
more accurate).
If the setting of the number of position pulses becomes very large, a

subtle difference in response may occur between two axes submitted
to interpolation, because of position gain canceling. To avoid this
problem, make the following setting.
#7 #6 #5 #4 #3 #2 #1 #0
1749 (FS15i) PGAT
2209 (FS30i, 16i)
PGAT(#6) The position gain precision optimization function is:
0: Disabled (conventional method)
1: Enabled
NOTE
1 Specify this function for all the simultaneous
contouring axes.
2 In servo software Series 90D0 and 90E0,
automatic format change for position gain is
enabled by default regardless of the PGAT setting.
So, PGAT need not be set.
(b) For servo software Series 9096

Because the "position feedback pulse conversion coefficient" is
unusable, change the parameters as stated below.
(i) If the number of position pulses is in a range from 32,768 to

131,000
Change the parameters according to the following table.
Parameter number
Method for changing parameters
Series 15i Series 30i, 16i, and so on
1804#0 2000#0 1
1876 2023 (Setting target)/10
1891 2024 (Setting target)/10
- 74 -
(ii) If the number of position pulses is larger than 131,000

Change the parameters according to the following table.
In this table, letter E satisfies:
Number of position feedback pulses/10/E < 13100
Parameter number
Method for changing parameters
1804#0 2000#0 1
1876 2023 (Setting target)/10/E
1891 2024 (Setting target)/10/E
1855 2043 (Setting target)/E
1859 2047 (Setting target)×E
(Quotient of setting target/256) ×E×256
1752 2129
+(remainder of setting target/256)
NOTE
When a setting is made using this method, the
actual speed multiplied by E is displayed on the
servo screen.
Supplementary 4: Function for changing the internal format of the velocity loop
proportional gain
An overflow may occur in the velocity loop proportional gain during
internal calculation by the servo software. This can be avoided by
setting the parameter shown below.
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) P2EX
2200 (FS30i, 16i)
P2EX (#6) 0: Uses the standard internal format for the velocity loop
proportional gain.
1: Changes the internal format of the velocity loop proportional
gain to prevent an overflow.
Supplementary 5: Preventing an overflow in the position gain or the feed-forward

coefficient
If the position gain or feed-forward coefficient overflows, take one of
the following measures depending on the servo software series in use.
- 75 -
(a) For other than servo software Series 9096

#7 #6 #5 #4 #3 #2 #1 #0
1749 (FS15i) PGAT
2209 (FS16i)
PGAT(#6) The position gain precision optimization function is:
0: To be disabled (conventional method)
1: To be enabled
NOTE
1 Specify this function for all the simultaneous
contouring axes.
2 When servo software Series 90D0 or 90E0 is used,
the function for automatic format change for
position gain is enabled by default, regardless of
the setting of PGAT. The parameter need not be
set.
(b) For servo software Series 9096

#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) PGEX
2000 (FS16i)
PGEX (#4) 0: Disables the position gain setting range expansion function.
1: Enables the position gain setting range expansion function.
The setting of the number of position pulses need not be changed.
If an overflow in the position gain cannot be prevented by this

function, change the CMR.
If the CMR is multiplied by N (integer), multiply also the flexible feed
gear by N. This means that the detection unit is refined to 1/N. So, the
settings of all parameters that need to be set in the detection unit need
to be increased by N.
See Appendix B for a list of the parameters set in the detection unit.
Supplementary 6: Support for the torque control setting range extension function
To use the torque control setting range extension function (bit 7 of No.
2301), CNC software that supports the function is required. The
following series and edition of CNC software support the function (as
of September 2007):
Series 16i-MB B0K1 – 06 and subsequent editions
Series 16i -TB B1K1 – 05 and subsequent editions
Series 18i -MB BDK1 – 06 and subsequent editions
Series 18i -TB BEK1 – 05 and subsequent editions
Series 18i -MB5 BDK5 – 06 and subsequent editions
Series 21i -MB DDK1 – 06 and subsequent editions
Series 21i -TB DEK1 – 05 and subsequent editions
Power Mate i-D 88E1 – 06, 88E3 – 04and subsequent editions
Power Mate i-H 88F2 – 13, 88F3 – 04and subsequent editions
- 76 -
2.1.9 Notes on Using the Control Axis Detach Function
(1) Overview
Servo software automatically identifies the type of detector connected
to an axis, when the power to the CNC is turned on. When the control
axis detach function is used, however, servo software cannot identify
the type of detector in a case where the power to the CNC is turned on
with the detector detached from the controlled axis. (An alarm such as
a communication alarm is issued.)
Such an alarm can be avoided by setting the parameter indicated
below.

Series 90D0/M(13) and subsequent editions
Series 90E0/M(13) and subsequent editions
Series 90B0/Ｗ(23) and subsequent editions
Series 90B5/A(01)and subsequent editions
Series 90B8/A(01)and subsequent editions

Set the following parameter for such an axis where the detector on the
semi-closed side may be disconnected from the servo amplifier:
#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) COMSRC
2017 (FS30i,16i)
COMSRC(#3) The detector on the semi-closed side is:
0: Automatically identified.
1: αi/βi pulse coder at all times.
NOTE
1 When this parameter is set, the power must be
turned off before operation is continued.
2 This parameter does not support an application
where a separate detector is disconnected.
- 77 -
3. αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT B-65270EN/07
3 αiS/αiF/βiS SERIES PARAMETER

ADJUSTMENT
This chapter describes parameter tuning for the FANUC AC SERVO
MOTOR αiS, αiF, and βiS series. A servo tuning tool, SERVO
GUIDE, is available which lets you perform parameter tuning
smoothly. See Section 4.22 for the summary of SERVO GUIDE.
Chapter 3, "αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT",

consists of the following sections:
3.1 SERVO TUNING SCREEN .......................................................79

3.2 ACTIONS FOR ALARMS .........................................................87
3.3 ADJUSTING PARAMETERS FOR HIGH-SPEED AND
HIGH-PRECISION MACHINING.............................................96
- 78 -
B-65270EN/07 3. αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT
3.1 SERVO TUNING SCREEN AND DIAGNOSIS

INFORMATION
3.1.1 Servo Tuning Screen

Display the servo tuning screen, and check the position error, actual
current, and actual speed on the screen.
Using the keys on the CNC, enter values according to the procedure
explained below. (The Power Mate i DPL/MDI does not provide the
servo tuning function.)
- Series 15i
Press the SYSTEM key several times to display the servo setting screen.
Then press the key to display the servo tuning screen.
- Series 30i, 31i, 32i, 16i, 18i, 21i, 20i, 0i, and Power Mate i
→ [SYSTEM] → [ ] → [SV-PRM] → [SV-TUN]
If the servo setting/tuning screen does not appear, set the following
parameter, then switch the CNC off and on again.
#7 #6 #5 #4 #3 #2 #1 #0
3111 SVS
SVS (#0) 1: Displays the servo setting/tuning screen.
<1> <9>
<2> <10>
<3> <11>
<4> <12>
<5> <13>
<6> <14>
<7> <15>
<8> <16>
<17>
<18>
Fig. 3.1.1(a) Servo tuning screen
- 79 -
<9> <20>
<10> <21>
<11>
<12>
<13>
Fig. 3.1.1(b) Diagnosis screen
<2> <14>
<5> <15>
<6> <16>
<8> <17>
<18>
<7>
Fig. 3.1.1(c) Series 15i servo tuning screen
<9> <19>
<10> <20>
<11> <21>
<12> <22>
<13>
Fig. 3.1.1(d) Series 15i servo diagnosis screen
The items on the servo tuning screen correspond to the following

parameter numbers:
- 80 -
Table 3.1 Correspondence between the servo tuning screen and diagnosis screen, and parameters
<1> Function bit No. 1808 No. 2003
<2> Loop gain No. 1825 No. 1825
<3> Tuning start bit Not used at present
<4> Setting period Not used at present
<5> Velocity loop integral gain No. 1855 No. 2043
<6> Velocity loop proportional gain No. 1856 No. 2044
<7> TCMD filter No. 1857 No. 2067
Related to No. 1875 Related to No. 2021
The relationship with the load inertia ratio (LDINT=No.1875,No.2021) is as
<8> Velocity loop gain
follows:
Velocity gain = (1 + LDINT/256) × 100 [%]
<9> Alarm 1 diagnosis Diagnosis Nos. 3014 + 20(X - 1) Diagnosis No. 200
<10> Alarm 2 Diagnosis Nos. 3015 + 20(X - 1) Diagnosis No. 201
<13> Alarm 5 __________ Diagnosis No. 204
<19> Alarm 6 __________ __________
<22> Alarm 9 __________ __________
<14> Loop gain or actual loop gain The actual servo loop gain is displayed.
Diagnosis No. 3000 Diagnosis No. 300
<15> Position error diagnosis Position error =
(feedrate) [mm/min] / (least input increment × 60 × loop gain × 0.01) [mm]
<16> Actual current [%] Indicates the percentage [%] of the current value to the continuous rated
current.
<17> Actual current [Ap] Indicates the current value (peak value).
<18> Actual speed [min-1] or [mm/min] Indicates the actual speed or feedrate.
- 81 -
3.1.2 Diagnosis Information List

The table below provides a list of servo-related data items displayed
on the diagnosis screen.
Table 3.1.2(a) Diagnosis number list

Diagnosis No. (DGN)
Unit of data Data description Remarks
Series30i Series16i Series15i
200 200 3014+20(x-1) - Alarm 1 → See Section 3.2
204 204 - - Alarm 5 → See Section 3.2
→ See Subsection
280 280 - - Invalid parameter details (CNC)
2.1.8
300 300 3000 Detection unit Positional deviation
308 308 3520 ℃ Servo motor temperature (Note 1)
309 309 3521 ℃ Pulse coder temperature
350 350 - - Servo state flag 1 (Note 2)
351 351 - - Servo state flag 2 (Note 3)
→ See Subsection
352 352 - - Invalid parameter details (SV)
2.1.8
353 353 - - Adjustment data #1
Adjustment data #2 → See Subsection
354 354 - -
Acceleration data 3.1.4
Separately installed in serial
Number of
355 355 - Communication alarm neglect
times
counter
Number of Built-in pulse coder
356 356 -
times Feedback extrapolation counter
Number of Separately installed in serial
357 357 -
times Feedback extrapolation counter
358 358 - - V-READY OFF information
Built-in pulse coder
Number of
359 - - Communication alarm neglect
times
counter
Command pulse accumulation
360 - - Detection unit
(NC)
361 - - Detection unit Compensation pulse (NC)
Command pulse accumulation
362 - - Detection unit
(SV)
363 - - Detection unit Feedback accumulation (SV)
Dual position Error on the
550 550 - Detection unit
full-closed side
semi-closed side
semi-/full-closed side
Dual position Compensation
value
- 82 -
Diagnosis no. (DGN)

Unit of data Data description Remarks
Series30i Series16i Series15i
700 700 3022 - Servo state flag 3 (Note 4)
750 - 3540 % OVC data Alarm with 100%
752 - - Vrms Voltage information (Note 5)
Imax=Maximum
760 - - Imax[Ap]/6554 R phase current value
amplifier current
Imax=Maximum
761 - - Imax[Ap]/8027 Effective current value
amplifier current
762 - - 360[deg]/256 Excitation phase data
Note 1: When a linear motor or synchronous built-in servo motor is

used and temperature information (thermistor signal) is
connected to a temperature detection circuit, αiCZ detection
circuit, or linear motor detection circuit, the temperature of
the motor can be displayed on diagnosis No. 308.
⇒ See the following subsections:
2.1.7 Setting Parameters When an Acceleration Sensor or
Temperature Detection Circuit Is Used
4.14.2 Detection of an Overheat Alarm by Servo Software
when a Linear Motor and a Synchronous Built-in
Servo Motor are Used
Note 2: Diagnosis No. 350 displays the following state signals:

#7 #6 #5 #4 #3 #2 #1 #0
- ALMTMP ALMACC A_PHAL PM0CHK PM0TMP PM0ACC PM0POS
Diagnosis 350 (FS30i,16i)
PM0POS(#0) 1: A position detector is connected to the first SDU unit.
PM0ACC(#1) 1: An acceleration sensor is connected to the first SDU unit.
PM0TMP(#2) 1: A temperature detection circuit is connected to the first SDU unit.
PM0CHK(#3) 1: A servo check interface unit is connected to the first SDU unit.
A_PHAL(#4) 1: An error has occurred in the EEPROM of the αi pulse coder.
(This is not an alarm.)
ALMACC(#5) 1: An alarm is issued from an acceleration sensor.
ALMTMP(#6) 1: An alarm is issued from a temperature detection circuit.

#7 #6 #5 #4 #3 #2 #1 #0
- PM1CHK PM1TMP PM1ACC PM1POS
PM1POS(#0) 1: A position detector is connected to the second SDU unit.
PM1ACC(#1) 1: An acceleration sensor is connected to the second SDU unit.
PM1TMP(#2) 1: A temperature detection circuit is connected to the second SDU
unit.
PM1CHK(#3) 1: A servo check interface unit is connected to the second SDU unit.
- 83 -

#7 #6 #5 #4 #3 #2 #1 #0
Diagnosis 3022 (FS15i) L2048 O2048 1VPP FSFMB PSFMB DCLNK HRV3OK HRV3ON
HRV3ON(#0) 1: The high-speed HRV current control mode is ON (HRV3, HRV4).
HRV3OK(#1) 1: The configured hardware enables high-speed HRV current control
and PDM to be used.
DCLNK(#2) 1: DC link voltage information can be used.
PSFMB(#3) 1: On the semi-closed side, a high resolution rotary scale (such as
RCN727) is connected.
FSFMB(#4) 1: On the full-closed side, a high resolution rotary scale (such as
RCN727) is connected.
1VPP(#5) 1: A detector is connected via an analog SDU unit.
O2048(#6) 1: The detector on the full-closed side enables 2048-magnification
interpolation setting.
L2048(#7) 1: The detector on the semi-closed side enables 2048-magnification
interpolation circuitry. (Linear motor)
Note 5: To use diagnosis data about voltage information, the

following software and hardware are required:
CNC software
Series 30i-A : Series G002, G012, G022 / 23.2 and
subsequent editions
: Series G003, G013, G023 / 06.2 and
subsequent editions
Series 31i -A : Series G101, G111 / 23.2 and subsequent
editions
: Series G103, G113 / 06.2 and subsequent
editions
Series 31i -A5 : Series G121, G131 / 23.2 and subsequent
editions
: Series G123, G133 / 06.2 and subsequent
editions
Series 32i -A : Series G201 / 23.2 and subsequent editions
: Series G203 / 06.2 and subsequent editions
Servo software : Series 90E0 / O(15) and subsequent
editions
: Series 90D0 / O(15) and subsequent
editions
αi PS (Power Supply) : A06B-6140-Hxxx
αi SV (Servo Amplifier) : A06B-6117-Hxxx
(servo amplifier for 30i)
- 84 -
3.1.3 Actual Current Peak Hold Display
(1) Overview
The servo tuning screen displays an actual current value (Ap) and a
ratio (%) to the rated current value. However, if current abruptly
changes during acceleration, for example, its value cannot be checked.
By setting the parameter indicated below, a peak current value is
displayed for about 3 seconds, so that a maximum current value
during acceleration can be read.

Series 9096/A(01) and subsequent editions

#7 #6 #5 #4 #3 #2 #1 #0
1741(FS15i) CPEEKH
2201(FS30i,16i)
PK2VDN (#6) 0: A current value is displayed as usually done.
1: The display of a peak current value is held.
NOTE
When reading an actual current by using an
application that uses SERVO GUIDE or the FOCAS
library or an application that uses the PMC window,
note that this function displays a waveform different
from an actual momentary current waveform.
Actual momentary current: Dashed line
Observed current: Solid line
3 seconds
3 seconds
3 seconds
- 85 -
3.1.4 Acceleration Monitor Function
(1) Overview
Width the acceleration monitor function, acceleration feedback can be
observed on diagnosis screen No. 354.

Series 90B1/I(09) and subsequent editions (*1)
Series 90B8/I(09) and subsequent editions (*1)
(*1) Series 90B1 and 90B8 do not support the function (bit 2 of No.
2290) for output of remaining acceleration data.

By setting bit 0 of No. 2290 to 1 after setting an acceleration sensor
(Subsection 2.1.7), acceleration feedback can be displayed on
diagnosis screen No. 354.
By setting bit 1 of No. 2290 to 1, a peak acceleration rate can be held
(for 1 second). By setting bit 2 of No. 2290 to 1, the remaining
acceleration data after a stop can be observed.
#7 #6 #5 #4 #3 #2 #1 #0
- ACCMON ACCHLD ACCOUT
2290(FS30i,16i)
ACCOUT(#0) To the diagnosis screen (No. 354), acceleration data output is:
0: Not performed.
1: Performed.
ACCHLD(#1) A peak acceleration rate is:
0: Not held.
1: Held (for 1 second).
ACCMON(#2) 0: Acceleration data is output at all times.
1: The remaining acceleration data after a stop is output. (The
acceleration data is cleared to 0 during movement and for 16 ms
after a stop.)
- Acceleration feedback
[Display unit] mm/s2
- 86 -
3.2 ACTIONS FOR ALARMS
If a servo alarm is issued, detail alarm information is displayed on the

diagnosis screen (Figs. 3.1 (b) and (d)). Based on this information,
check the cause of the servo alarm and take appropriate action. For
alarms with no action number, refer to relevant manuals such as the
maintenance manual on the amplifier.
Table 3.2 Alarm bit names
#7 #6 #5 #4 #3 #2 #1 #0
Alarm 1 OVL LVA OVC HCA HVA DCA FBA OFA
Alarm 2 ALD EXP
Alarm 3 CSA BLA PHA RCA BZA CKA SPH
Alarm 4 DTE CRC STB PRM
Alarm 5 OFS MCC LDM PMS FAN DAL ABF
Alarm 6 SFA
Alarm 7 OHA LDA BLA PHA CMA BZA PMA SPH
Alarm 8 DTE CRC STB SPD
Alarm 9 FSD SVE IDW NCE IFE
NOTE
The blank fields do not contain any alarm code.
(1) Alarms related to the amplifier and motor
Alarm 1 Alarm 5 Alarm 2

Description Action
OVL LVA OVC HCA HVA DCA FBA MCC FAN ALD EXP
1 0 0 Overcurrent alarm (PSM)
1 0 1 Overcurrent alarm (SVM) 1
1 0 1 Overcurrent alarm (software) 1
1 Excessive voltage alarm
Excessive regenerative discharge
1
alarm
Alarm indicating insufficient power
1 0 0
voltage (PSM)
1 1 0 Insufficient DC link voltage (PSM)
Insufficient control power voltage
1 0 1
(SVM)
1 1 1 Insufficient DC link voltage (SVM)
1 0 0 Overheat (PSM) 2
1 1 0 Motor overheat 2
1 1 1 Motor overheat (Note2) 2
1 MCC fusing, precharge
1 0 0 Fan stopped (PSM)
1 0 1 Fan stopped (SVM)
1 OVC alarm 3
- 87 -
NOTE
1 For alarms with no action number indicated, refer
to the Maintenance Manual.
2 OVL = 1, ALD = 1, and EXP = 1 indicate an
overheat alarm using DI signals in a linear motor or
a synchronous built-in servo motor and are set
when bit 7 of parameter No. 2713 (Series 15i) or bit
7 of parameter No. 2300 (Series 30i, 16i, and so
on) is set to 1. When these alarms are issued, take
the same action as for ordinary motor overheat
alarms. (See the Subsection 4.14.2, "Detection of
an Overheat Alarm by Servo Software when a
Linear Motor and a Synchronous Built-in Servo
Motor are Used".)
Action 1: Overcurrent alarms

This type of alarm is issued when an extremely large current flows
through the main circuit.
When an overcurrent alarm is always issued after emergency stop is
released or at the time of moderate acc./dec., the cause of the alarm is
determined to be an amplifier failure, cable connection error, line
disconnection, or a parameter setting error. First, check that standard
values are set for the following servo parameters. If these parameter
settings are correct, check the amplifier and cable status by referring
to the maintenance manual on the servo amplifier.
Parameter No.
Details
Series15i Series 30i, 16i and so on
1809 2004 HRV setting
1852 2040 Current loop gain (PK1)
If an overcurrent alarm is issued only when an strong acc./dec. is

performed, the operating conditions may be too abrupt. Increase the
acc./dec. time constant, and see whether the alarm is issued.
- 88 -
CAUTION
1 If an overcurrent alarm is detected, and the LED
indication in the amplifier remains set to "−", the
overcurrent alarm may have been detected by the
servo software. The cause may be one of the
following:
- The contact of the power line is poor, or the
power line is disconnected or broken.
- The AMR conversion coefficient or AMR offset is
not set correctly.
2 If the emergency stop state is released without
connecting the power line in a test such as a test
for machine start-up, the servo software may
detect an overcurrent alarm. In such a case, the
alarm can be avoided temporarily by setting the bit
parameter indicated below to 1. However, be sure
to return the bit parameter to 0 before starting up in
the normal operation state after completion of a
test.
To ignore the overcurrent alarm (software), set the
following:
- No1747#0 (Series15i)
- No2207#0 (Series 30i, 16i, and so on)
Action 2: Overheat alarms

If an overheat alarm occurs after long-time continuous operation, the
alarm can be determined to have been caused by a temperature rise in
the motor or amplifier. Stop operation for a while. If the alarm still
occurs after the power is kept off for about 10 minutes, the hardware
may be defective.
If the alarm occurs intermittently, increase the time constant, or
increase the programmed stop time period to suppress temperature
rise.
Motor and Pulsecoder temperature information is displayed on the
diagnosis screen.
Series 30i, 16i, and so on Series15i
Motor temperature (°C) Diagnosis No.308 Diagnosis No.3520
Pulsecoder temperature
Diagnosis No.309 Diagnosis No.3521
(°C)
- 89 -
Action 3: OVC alarms

When an OVC alarm occurs, check that standard values are set for the
following parameters. If the parameters are correct, increase the time
constant or increase the programmed stop time period to suppress
temperature rise.
Parameter No.
Details
Series15i Series 30i, 16i and so on
Overload protection coefficient
1877 2062
(POVC1)
Overload protection coefficient
1878 2063
(POVC2)
1893 2065 Soft thermal coefficient (POVCLMT)
OVC magnification at a stop
1784 2161
(OVCSTP)
Overload protection coefficient 2
1785 2162
(POVC21)
Overload protection coefficient 2
1786 2163
(POVC22)
Soft thermal coefficient 2
1787 2164
(POVCLMT2)
For the Series 30i and 15i, OVC data is displayed on the diagnosis
screen. (An OVC alarm occurs when OVC data is set to 100%.)
The Series 16i enables OVC status to be checked as thermal
simulation data with the waveform diagnosis function and the trouble
diagnosis function.
Series 30i and so on Series 15i
OVC data (%) Diagnosis No.750 Diagnosis No.3540
- 90 -
(2) Alarms related to the Pulsecoder and separate serial Pulsecoder

(2-1) αi Pulsecoder
These alarms are identified from alarms 1, 2, 3, and 5. The
meanings of the bits are as follows:
Alarm 3 Alarm 5 1 Alarm 2

Description Action
CSA BLA PHA RCA BZA CKA SPH LDM PMS FBA ALD EXP
1 Soft phase alarm 2
1 Clock alarm
1 Zero volts in battery 1
1 1 1 0 Count error alarm 2
1 EEPROM abnormal alarm
Voltage drop in battery
1 1
(Warning)
1 Pulse error alarm
1 LED abnormality alarm
CAUTION
For alarms with no action number indicated, the
Pulsecoder may be defective. Replace the
Pulsecoder.
(2-2) Separate serial detector coder

These alarms are identified from alarm 7. The meanings of the
bits are as follows:
Alarm 7
Description Action
OHA LDA BLA PHA CMA BZA PMA SPH
1 Soft phase alarm 2
1 Pulse error alarm
1 Zero volts in battery 1
1 Count error alarm 2
1 Phase alarm 2
Voltage drop in battery
1 1
(Warning)
1 LED abnormality alarm
1 Separate detector alarm
CAUTION
For alarms with no action number indicated, the
detector may be defective. Replace the detector.
Action 1: Battery-related alarms

Check whether the battery is connected. When the power is
turned on for the first time after the battery is connected, a
battery zero alarm occurs. In this case, turn the power off then on
again. If the alarm occurs again, check the battery voltage. If the
battery voltage drop alarm occurs, check the voltage, then
replace the battery.
- 91 -
Action 2: Alarms that may occur due to noise

When an alarm occurs intermittently or occurs after emergency
stop is released, there is a high possibility that the alarm is
caused by noise. Take thorough noise-preventive measures. If the
alarm still occurs continuously after the measures are taken,
replace the detector.
(3) Alarms related to serial communication

These alarms are identified from alarms 4 and 8.
Alarm 4 Alarm 8
Description
DTE CRC STB PRM DTE CRC STB SPD
1
1 Communication alarm in serial Pulsecoder
1
1
1 Communication alarm in separate serial Pulsecoder
1
Action: Serial communication is not performed correctly. Check

whether cable connection is correct and whether there is a
line disconnection. If CRC or STB occurs, the alarm may be
caused by noise. Take noise-preventive measures. If the
alarm always occurs after power is turned on, the Pulsecoder,
the control board of the amplifier (i series), or the separate
detector interface unit (i series) may be defective.
(4) Disconnection alarms

These alarms are identified from alarms 1, 2, and 6.
Alarm 1 Alarm 2 6
Description Action
OVL LVA OVC HCA HVA DCA FBA ALD EXP SFA
Hardware disconnection
1 1 1 0 1
(separate phase A/B disconnection)
1 0 0 0 Software disconnection (closed loop) 2
1 0 0 1 Software disconnection (α Pulsecoder) 3
Action 1: This alarm occurs when the separate phase A/B scale is
used. Check whether the phase A/B detector is connected
correctly.
Action 2: This alarm occurs when the change in position feedback
pulses is relatively small for the change in velocity
feedback pulses. Therefore, with the semi-closed loop, this
alarm does not occur. Check whether the separate detector
outputs position feedback pulses correctly. If the detector
outputs pulses correctly, the alarm is determined to have
been caused by the reverse rotation of only the motor at the
start of machine operation because of a large backlash
between the motor position and scale position.
- 92 -
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) TGAL
2003 (FS30i, 16i)
TGAL (#1) 1: The level for detecting the software disconnection alarm is set by
parameter.
1892 (FS15i) Software disconnection alarm level

2064 (FS30i, 16i)
Standard setting 4: Alarm occurs when motor turns 1/8 of a turn.
Increase this value.
Action 3: This alarm occurs when the absolute position data sent from
the built-in Pulsecoder cannot be synchronized with the
phase data. Remove the Pulsecoder cable with the NC
power switched off and wait for about 10 minutes, then
connect the cable again. If this alarm occurs again, replace
the Pulsecoder.
When an absolute type linear encoder is used with a linear
motor or when a synchronous built-in servo motor is used,
this alarm must be ignored because the detector does not
have phase data. Set the following bit.
#7 #6 #5 #4 #3 #2 #1 #0
1707(FS15i) APTG
2013(FS30i ,16i)
APTG(#7) 1: Ignores α Pulsecoder software disconnection.
(5) Illegal servo parameter setting alarm

This alarm is identified from alarm 4.
Alarm 4
Description
DTER CRC STB PRM
Illegal servo parameter setting
1
detected by servo software
If PRM is set to 1, an illegal servo parameter setting has been detected
by the servo software. Investigate the cause of the alarm according to
Subsec. 2.1.8, "Actions for Illegal Servo Parameter Setting Alarms."
(6) Other alarms

Alarms are identified from alarm 5. The meanings of the bits are as
follows:
Alarm 5
Description Action
OFS MCC LDM PMS FAN DAL ABF
1 Feedback mismatch alarm 1
1 Excessive semi-closed loop error alarm 2
1 Current offset error alarm 3
- 93 -
Action 1: This alarm occurs when the move directions for the position
detector and velocity detector are opposite to each other.
Check the rotation direction of the separate detector. If the
direction is opposite to the direction in which the motor
turns, take the following action:
__
Phase A/B detector: Switch the A and A connections.
Serial detector: Switch the signal direction setting for
the separate detector.
The following servo software allows the signal directions
to be reversed by setting the parameter shown below even
when a detector of A/B phase parallel type is used.
(Series 15i-B,16i-B,18i-B,21i-B,0i-B,0i Mate-B,
Power Mate i)
Series 90B0/G(07) and subsequent editions
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) RVRSE
2018 (FS30i, 16i)
RVRSE (#0) The signal direction for the separate detector is:
0: Not reversed.
1: Reversed.
When there is a large torsion or backlash between the motor and

separate detector, this alarm may occur when an abrupt acc./dec. is
performed. In such a case, change the detection level.
#7 #6 #5 #4 #3 #2 #1 #0
1741 (FS15i) RNLV
2201 (FS30i, 16i)
RNLV (#1) Change of the feedback mismatch alarm detection level
0: To be detected at 600 min-1 or more
1: To be detected at 1000 min-1 or more
Action 2: This alarm occurs when the difference between the motor
position and the position of the separate detector becomes
larger than the semi-closed loop error level. Check that the
dual position feedback conversion coefficient is set
correctly. If the setting is correct, increase the alarm level.
If the alarm still occurs after the level is changed, check the
scale connection direction.
- 94 -
1971 (FS15i) Dual position feedback conversion coefficient (numerator)

2078 (FS30i, 16i)
1972 (FS15i) Dual position feedback conversion coefficient (denominator)

2079 (FS30i, 16i)
Number of feedback pulses per

motor revolution (detection unit)
Conversion coefficient =
1,000,000
1729 (FS15i) Dual position feedback semi-closed loop error level

2118 (FS30i, 16i)
[Setting unit] Detection unit. When 0 is set, detection does not take place.
Action 3: The current offset (equivalent to the current value in the

emergency stop state) of the current detector becomes too
large. If the alarm occurs again after the power is turned on
and off, the current detector may be abnormal. Replace the
amplifier.
- 95 -
3.3 ADJUSTING PARAMETERS FOR HIGH-SPEED AND

HIGH-PRECISION MACHINING
3.3.1 Servo HRV Control Adjustment Procedure
(1) Overview
For higher positioning precision, higher precision in machined surface
and machining profile, shorter machining time, and other
improvements in machine tools, servo adjustment is required. This
subsection explains the servo adjustment procedure using servo HRV
control. In the i series CNCs (such as the Series 30i and 16i), servo
adjustments can be made easily by using SERVO GUIDE, which
supports adjustments.
(2) Outline of the adjustment procedure

Before servo control performance can be improved by servo
adjustment, it is necessary to understand these procedures and make
adjustments step by step accordingly. Servo control is implemented by
the structure shown in the block diagram below. Servo HRV current
control, which is located just before the motor in the regulation loop,
drives the motor according to the command output by high-speed
velocity control. The performance of high-speed velocity control is
supported by the performance of servo HRV current control.
High-speed velocity control controls the motor speed according to the
velocity command output by position control. To attain the final target,
which is to improve the capability to follow up position commands, a
higher position gain must be set. This requires improvement of
high-speed velocity control performance. Hence, this requires
improvement in servo HRV current control performance.
Therefore, in servo adjustment for improving the performance of
servo control, the highest priority is given to the improvement in servo
HRV current control, the next highest priority is given to the
improvement in high-speed velocity control, then the third priority is
given to the improvement of position control. Be sure to follow this
order.
Feed-forward
Command
from the
CNC Fine Position High-speed Resonance Servo HRV
Acc./Dec. + velocity loop elimination current control
gain +
filter
Servo HRV control improves the response speed of the current loop,
therefore, higher gains can be set for the velocity loop and position
loop. Increased gains lead not only to improvement in command
follow-up performance and disturbance suppression performance but
also to simplification in servo function adjustments such as quadrant
protrusion compensation. As a result, servo adjustments can be made
more easily.
- 96 -
The figure below shows the results of a gain adjustment for each servo
HRV control type. The figure indicates that improvement in response
speed of the current loop by servo HRV control further improves the
response speed of velocity control and position control, and therefore
quadrant protrusions can be reduced without the backlash acceleration
function.
Servo HRV1 control Servo HRV2 control Servo HRV3 control
R100mm 10000mm/min without backlash acceleration function
This manual explains the servo adjustment procedure in the following

order:
• Initialization of parameters related to high-speed and
high-precision machining
Before starting the servo adjustment for high-speed and
high-precision machining, set minimum required parameters.
• Servo HRV control setting
Select the servo HRV control type. Select suitable servo HRV
control from servo HRV2, HRV3, and HRV4.
• Adjustment of high-speed velocity control
Adjust the velocity loop gain and filter by using SERVO
GUIDE.
• Adjustment of acc./dec. in rapid traverse
Adjust the time constant for rapid traverse. In position gain
setting made in the next step, the limit is confirmed by checking
stability during rapid traverse.
• Position gain adjustment
Adjust the position gain while observing the TCMD and motor
speed in rapid traverse and cutting feed.
• Adjustment by using an arc
Adjust the feed-forward and backlash acceleration while
measuring an arc figure.
• Adjustment by using a square figure
Adjust the reduced feedrate and the acceleration for deceleration
at a corner while measuring the corner figure.
• Adjustment by using a square figure with 1/4 arcs
Adjust the velocity in the round corners while measuring the
contour error in the round corners.
- 97 -
(3) Initialization of parameters related to high-speed and high-precision

machining
The parameter values to be set first before servo adjustments are made
are listed below. Sufficient performance can be obtained just by
setting these values. Furthermore, by separately adjusting the settings
indicated by gray shading, much higher speed and higher precision
can be obtained.
[Fundamental Parameters]
Parameter No.
Standard setting value Description
FS15i FS30i, 16i, and so on
1809 2004 0X000011 (Note 1) Enables HRV2 control
1852 2040 Standard parameter (Note 1) Current integral gain
1853 2041 Standard parameter (Note 1) Current proportional gain
1808 #3 2003 #3 1 (Note 2) Enables PI function
1959 #7 2017 #7 1 (Note 3) Enables velocity loop high cycle management function
1884 #4 2006 #4 1 Enables 1-ms velocity feedback acquisition
1958 #3 2016 #3 1 Enables variable proportional gain in the stop state
For variable proportional gain function in the stop state :
2 (detection unit of 1 µm)
1730 2119 judgment level for stop state
20 (detection unit of 0.1µm)
(specified in detection units)
1825 1825 5000 Servo loop gain
1875 2021 128 Load Inertia ratio (Velocity Loop Gain) (Note 4)
1742 #1 2202 #1 1 Cutting/rapid traverse velocity loop gain variable
1700 2107 150 Velocity loop gain override at cutting traverse
NOTE
1 Optimum parameters can be loaded automatically by setting a motor ID number for
servo HRV2 control.
If there is no motor ID number for servo HRV2 control, load the standard
parameters for servo HRV1, then calculate parameter values as follows:
No. 2004 = 0X000011 (Keep X unchanged.)
No. 2040 = Standard parameter for HRV1 × 0.8
2 To use I-P function, set 0.
PI function and I-P function have the following features:
PI function: Provides good follow-up to a target command. This function is required
for high-speed and high-precision machining.
I-P function: Requires a relatively short time to attain a target position. This function
is suitable for positioning applications.
3 With some machines, a higher velocity loop gain can be set by using neither the
acceleration feedback function nor auxiliary function rather than by using these
functions. If it is impossible to set a high velocity loop gain (about 300%) when the
velocity loop high cycle management function is used, try to use the acceleration
feedback function (See Subsection 4.4.2), and use the function that allows a higher
velocity loop gain to be set.
4 There is the following relationship between the load inertia ratio and velocity loop
gain (%).
Velocity loop gain (%) = (1 + load inertia ratio / 256) × 100
- 98 -
[Feed-forward and FAD(Fine acc./dec.)]

Parameter No.
Standard setting
FS30i, 16i, Description
FS15i value
and so on
1951 #6 2007 #6 1 Enables FAD (Fine acc./dec.) (Note 1)
1749 #2 2209 #2 1 Enables FAD of linear type.
1702 2109 16 FAD time constant (Note 2)
1883 #1 2005 #1 1 Enables feed-forward
1800 #3 1800 #3 0 Feed-forward at rapid traverse (Note 2)
1959 #5 2017 #5 1 RISC feed-forward is improved
1740 #5 2200 #5 1 RISC feed-forward is improved
1985 2092 10000 Advanced preview feed-forward coefficient
1962 2069 50 Velocity feed-forward coefficient
NOTE
1 With the Series 30i, Series 31i, and Series 32i, which use nano interpolation
as a standard function, the fine acc./dec. function is not required.
During AI nano contour control, AI contour control, and high precision
contour control, the fine acc./dec. function is disabled. So, set the time
constant of acc./dec. after interpolation on the CNC side.
2 As the time constant of fine acc./dec., be sure to set a multiple of 8.
When using fine Acc./Dec also in rapid traverse, enable rapid traverse
feed-forward, or use the cutting/rapid FAD switching function (see
Subsection 4.8.3).
3 RISC feed-forward is enabled during AI contour control and high precision
contour control and allows smoother feed-forward operation.
[Backlash Acceleration]
Parameter No.
FS30i, 16i, Standard setting value Description
FS15i
and so on
1851 1851 1 or more Backlash compensation
1808 #5 2003 #5 1 Enables backlash acceleration
0 : Semi-close system
1884 #0 2006 #0 0/1
1 : Full-close system
1953 #7 2009 #7 1 Backlash acceleration stop
1953 #6 2009 #6 1 Backlash acceleration only at cutting feed (FF)
2611 #7 2223 #7 1 Backlash acceleration only at cutting feed (G01)
1957 #6 2015 #6 0 Two-stage backlash acceleration (Note)
1769 2146 50 Two-stage backlash acceleration end timer
1860 2048 100 Backlash acceleration amount
5 (detection unit of 1 µm)
1975 2082 Backlash acceleration stop timing
50 (detection unit of 0.1 µm)
1964 2071 20 Backlash acceleration time
NOTE
The above table lists the initial values set when the conventional backlash
acceleration function is used. When much higher precision is required, use
the two-stage backlash acceleration function.
- 99 -
[Time Constant]
Set the initial value of the time constant of acc./dec. according to the
high-speed and high-precision function of the CNC used. Adjust the
time constant of acc./dec. to an optimum value while checking the
rapid traverse and cutting feed operations.
• AI nano contour control, AI contour control, AI advanced

preview control, and advanced preview control
Parameter No. Standard
Description
FS16i and so on setting value
1620 200 Time constant of acc./dec. in rapid traverse - linear part (ms)
1621 200 Time constant of acc./dec. in rapid traverse - bell-shaped part (ms)
1770 10000 Acc./dec. before interpolation: Maximum cutting feedrate
1771 240 Acc./dec. before interpolation: Time (ms) Æ 0.07G
Acc./dec. before interpolation: Bell-shaped time constant (ms) (for other than
1772 64
advanced preview control)
1768 24 Time constant for acc./dec. after interpolation (ms)
• AI nano high-precision contour control, AI high-precision

contour control, and high-precision contour control
Description
FS16i and so on setting value
8400 10000 Acc./dec. before interpolation: Maximum cutting feedrate
Acc./dec. before interpolation: Time (ms) Æ 0.07G (No. 8401 for high precision
19510 240
contour control)
8416 64 Acc./dec. before interpolation: Bell-shaped time constant (ms)
• AI contour control I and AI contour control II (Series 30i, Series

31i, and Series 32i)
Description
FS30i setting value
1660 700 Acc./dec. before interpolation: Acceleration(mm/s2) Æ 0.07G
1769 24 Time constant for Acc./dec. after interpolation (ms)
• Series 15i
Description
FS15i setting value
1620 200 Time constant of Acc./dec. in rapid traverse - linear part (ms)
1636 200 Time constant of Acc./dec. in rapid traverse - bell-shaped part (ms)
1660 700 Acc./dec. before interpolation: Acceleration(mm/s2) Æ 0.07G
Permissible acceleration in velocity reduction based on acceleration (HPCC mode)
1663 700
(mm/s2)
- 100 -
(4) Servo HRV control setting

Set the type of servo HRV control. The setting of servo HRV2 is
always required. So, load the standard parameters for servo HRV2 by
following the description given below. Then, set HRV3 or HRV4 as
necessary.
(For Series 30i)
In standard setting, servo HRV2 control is set. However, to make
high-speed and high-precision adjustments, servo HRV3 is
recommended. If sufficient precision cannot be obtained with
servo HRV3, consider using servo HRV4. (See Subsec. 4.2.2.)
(For other than Series 30i)
In standard setting, servo HRV2 control is set. However, if
sufficient precision cannot be obtained with servo HRV2,
consider using servo HRV3. (See Subsec. 4.2.1.)
(a) Servo HRV2 control

By setting a motor ID number for servo HRV2 control, load the
standard parameters.
NOTE
If there is no motor ID number for servo HRV2
control, load the standard parameters for servo
HRV1, then calculate parameter values as follows:
No. 2004 = 0X000011 (Keep X unchanged.)
(b) Servo HRV3 control

After setting servo HRV2 control, set the following parameters:
[HRV3 parameters] (for FS15i, FS16i, and so on)

Parameter No. Recommended
Description
FS15i FS16i value
1707#0 2013#0 1 Enables HRV3 current control.
Enables the cutting/rapid velocity loop
1742#1 2202#1 1
gain switching function.
Enables high-speed HRV current control
- 2283#0 1
in cutting feed (Note 1).
2747 2334 150 Current gain magnification in HRV3 mode
2748 2335 200 Velocity gain magnification in HRV3 mode
NOTE
1 To use high-speed HRV current control, G codes need
to be set. (High-speed HRV current control is enabled
between G5.4Q1 and G5.4Q0.)
2 With Series 90B0, 90B1, 90B5, 90B6, and 90B8, the
torque command during high-speed HRV current control
is limited to 70% of the maximum value.
- 101 -
[HRV3 parameters] (for FS30i)

Description
FS30i value
2013#0 1 Enables HRV3 current control.
2202#1 1
2334 150 Current gain magnification in HRV3 mode
2335 200 Velocity gain magnification in HRV3 mode
NOTE
1 When N2283#0=1, no G code is needed.
2 To use high-speed HRV current control when
N2283#0=0, G codes need to be set. (High-speed HRV
current control is enabled between G5.4Q1 and
G5.4Q0.)
3 Series 90E0 imposes such a restriction that when servo
HRV3 control is used, the maximum number of axes per
servo card decreases.
(c) Servo HRV4 control

After setting servo HRV2 control, set the parameters listed below.
Servo HRV4 control and servo HRV3 control cannot be set at the
same time.
[HRV4 parameters]
Description
FS30i value
2014#0 1 Enables HRV4 current control.
2300#0 1 Enables the extended HRV function.
2202#1 1
Current gain magnification in high-speed
2334 150
HRV current control
Velocity gain magnification in high-speed
2335 200
HRV current control
NOTE
1 Servo HRV4 can be used with Series 90D0.
2 Use of servo HRV4 decreases the maximum
number of axes per servo card and limits the
maximum torque of the servo motor to 70%. For
details, see Subsection 4.2.2, "Servo HRVV4
Control".
3 To use high-speed HRV current control, G codes
must be set. (High-speed HRV current control is
enabled between G5.4Q1 and G5.4Q0.)
- 102 -
(5) Adjustment of high-speed velocity control

After setting servo HRV control, adjust the velocity loop gain and the
resonance elimination filter.
To obtain high servo performance, a high velocity loop gain must be
set. Some machines, however, vibrate easily at a particular frequency,
and setting a high velocity loop gain can cause vibration at that
frequency (machine resonance). As a result, it becomes impossible to
set a high velocity loop gain.
In such a case, the resonance elimination filter must be adjusted. The
resonance elimination filter can lower the gain only in an area around
a particular frequency, therefore allowing a high velocity loop gain to
be set without the occurrence of machine resonance.
The velocity loop gain and the resonance elimination filter can be
adjusted more easily by using Tuning Navigator of SERVO GUIDE.
(a) Adjusting the velocity loop gain and the resonance elimination filter (when
Tuning Navigator is used)
For adjustment of the resonance elimination filter, Tuning Navigator
of SERVO GUIDE can be used. On the main bar of SERVO GUIDE,
press the [Navigator] button.
[Starting Tuning Navigator]
Clicking this button displays the menu as shown below.
<1>
<2>
<3>
(Procedure for adjusting the velocity loop gain and the resonance
elimination filter)
In the adjustment of the velocity loop gain and the resonance
elimination filter, use <1> through <3> in the above figure. Make
adjustments in order from <1>.
- 103 -
<1> Initial Gain Tuning

Initial Gain Tuning determines the velocity loop gain value with
a margin for the oscillation limit. By making this adjustment, a
higher velocity gain than the initial value is set, so the frequency
of machine resonance can be determined clearly.
First, select Initial Gain Tuning from the dialog box of Tuning
Navigator.
Under 10dB
Under -20dB
Wide
Tuning Navigator shows bode-plot of velocity loop and you can

check the performance of velocity loop.
Upper line in bode-plot shows gain characteristic and lower line
shows phase characteristic. Important points of this figure that
you should note are as follows. (About the details of bode-plot,
please refer to several books of basic control method)
• The width of 0dB level of gain line is important. By setting
higher velocity loop gain, it becomes wide.
• Gain level of resonance frequency has to be suppressed at
least under -10dB.
• Gain level around cut-off frequency is less than 10dB.
• Gain level near 1000Hz has to be lower than -20dB.
<2> Filter Tuning
Next, select Filter Tuning from Tuning Navigator to adjust the
resonance elimination filter to suppress machine resonance.
Following example shows that gain line at two resonance
frequencies (250Hz and 530Hz) are suppressed by Filter Tuning.
Under -10dB
<3> Gain Tuning

Finally, select "Gain Tuning". Tuning Navigator decides the final
result of gain tuning. By adjusting the resonance elimination
filter, the influence of machine resonance can be eliminated, so a
high velocity loop gain can be set.
- 104 -
(b) Adjusting the velocity loop gain and the resonance elimination filter (when
Tuning Navigator is not used)
A）Adjustment by torque command waveform
1. Perform rapid traverse with a full stroke of the machine, and
observe the torque command when the machine is stopped
and when the machine moves at high speed. (The sampling
cycle period should be 125 µs.)
NOTE
When using the cutting/rapid velocity loop gain
switching function, perform cutting feed at the
maximum cutting feedrate to also check the
cutting-time oscillation limit.
2. As the velocity loop gain is increased gradually, the

following oscillation phenomena occur:
• Vibration occurs in the torque command waveform.
• Vibration sound is generated from the machine.
• A large variation in positional deviation is observed
when the machine movement stops.
3. Perform frequency analysis (Ctrl-F) for the torque
command issued when the above phenomena occur, and
measure the vibration frequency.
4. Set the measured vibration frequency as the attenuation
center frequency, and set the initial values of the attenuation
bandwidth and damping by consulting the setting guideline.
[Setting guideline]
Resonance frequency Attenuation bandwidth Damping
(Note 3)
Lower than 150 Hz Decrease the velocity loop gain.
(Note 3)
150 to 200 Hz Decrease the velocity loop gain.
200 to 400 Hz 60 to 100Hz 0 to 50%
Higher than 400 Hz 100 to 200Hz 0 to 10%
[Parameter Nos.]
Attenuation
Attenuation
center Damping
Series 30i, 16i bandwidth
frequency [%]
[Hz]
[Hz]
Resonance elimination filter 2 No.2360 No.2361 No.2362
Attenuation
Attenuation
center Damping
Series 15i bandwidth
frequency [%]
[Hz]
[Hz]
- 105 -
NOTE
1 The disturbance elimination filter (see Subsection
4.5.4) may be effective.
2 When the resonance elimination filter is used, set a
narrow attenuation bandwidth (about 50 Hz or less)
and a large damping attenuation factor (about 50%
to 80%).
3 When the center frequency becomes 200 Hz or
lower, almost the same effect as when the velocity
loop gain is decreased is obtained. Since the
resonance elimination filter also has the effect in
the change of phase, decreasing the velocity loop
gain is recommended.
4 The resonance elimination filter becomes more
effective as damping becomes closer to 0%.
Therefore, when adjusting damping, start with a
large value and decrease it gradually.
When SERVO GUIDE can be used, the resonance elimination filter

can be set from the parameter window.
[Starting the parameter window]
Clicking this button displays the parameter window.
[Parameter window main screen] [Velocity control + filter]
- 106 -
5. After setting the resonance elimination filter in step 4,

measure the torque command again. If there is still vibration
left at the same frequency, decrease the damping setting. If
vibration occurs at a frequency other than the set frequency,
it may be adversely influenced by the setting of the
resonance elimination filter. So, try to increase the setting of
damping to about 80% to reduce the influence of the
resonance elimination filter on velocity control. If vibration
is still observed, stop setting the resonance elimination filter
and decrease the velocity loop gain.
6. After determining the attenuation bandwidth and damping,

increase the velocity loop gain again until vibration
phenomena listed in step 2 occur. The final value of the
velocity loop gain is 70% to 80% of the velocity loop gain
set when the vibration phenomena occur.
B) Adjustment using the frequency characteristics

The velocity loop gain can be adjusted also by increasing the
velocity loop gain while measuring the frequency characteristics.
As the velocity loop gain increases, the gain at a certain
frequency swells in the frequency characteristics. The frequency
corresponding to the swell is the resonance frequency. So, the
velocity loop gain is increased while the swell in gain is
suppressed with the resonance elimination filter.
The velocity loop gain to be set is 70% to 80% of the velocity
loop gain observed when the swell can no longer be suppressed
by the resonance elimination filter. It is regarded as the final
setting if there is no problem during rapid traverse and cutting
feed at the maximum feedrate. If vibration occurs, decrease the
velocity loop gain until the vibration stops.
For measurement of the frequency characteristics, see Item (6)
"Frequency characteristic measurement method" in the Appendix
H, "DETAILS OF HIGH-SPEED AND HIGH-PRECISION
ADJUSTMENT".
(6) Adjustment of acc./dec. in rapid traverse

The time constant of acc./dec. in rapid traverse is adjusted. Adjusting
the time constant in rapid traverse can reduce the total machining time.
While observing the torque command (TCMD) at the time of acc./dec.
in rapid traverse to check that the TCMD does not reach the maximum
current value, decrease the time constant of acc./dec. in rapid traverse.
When bell-shaped acc./dec. in rapid traverse is used, a small TCMD
value can be obtained with mechanical impact suppressed.
NOTE
Make adjustments in rapid traverse with the
maximum load applied to the machine.
- 107 -
The following graphs show how the time constant in rapid traverse is
adjusted.
Feedrate Feedrate
TCMD TCMD
Maximum current Maximum current
- 108 -
[Parameter window main screen] [Acc./dec. + normal control]
(7) Adjustment of the position gain

Observe the torque command waveform at the time of acc./dec. during
rapid traverse and cutting feed at the maximum cutting feedrate. When
a low frequency vibration (hunting) of about 10 to 30 Hz occurs in the
torque command waveform, the corresponding position gain is
regarded as the oscillation limit. The position gain to be set is about
80% of the position gain of the oscillation limit.
The standard setting is within 5000 to 10000.
<3> Feedrate <4> <5>
<2>
<1> TCMD
<3> <4> <5> <7>
<2>
(Check points)
• No vibration is allowed in the stopped state. Also check the
positional deviation on the CNC. (<1>)
• Neither vibration nor sound must be generated during
acceleration and deceleration. If the TCMD level has reached the
maximum value, increase rapid traverse acc./dec. time constant
T1. (<2>, <5>)
• Neither vibration nor excessive overshoot must be generated at
the end of acceleration and deceleration. If the TCMD level has
reached the maximum value, increase rapid traverse acc./dec.
time constant T2. (<3>, <7>)
• There must be no large variation in feedrate during movement at
a constant feedrate. (<4>)
- 109 -
NOTE
For axes for which interpolation is performed, set
the same position gain.
[Parameter window main screen] [Position control]
(8) Adjustment by using an arc (adjustment of the feed-forward coefficient

and adjustment of the servo function)
(a) Feed-forward function
For higher precision with small servo follow-up delay, the
feed-forward function is used. When the feed-forward coefficient is
set to 100%, the positional deviation can be almost eliminated.
(Feed-forward)
By adding to a velocity command value the velocity
compensation value equivalent to the position command issued
from the CNC, the contour error due to position loop response
delay can be reduced.
(Velocity feed-forward)
The torque compensation amount equivalent to the amount of
change in velocity command (acceleration) is added to a
specified torque value so that the contour error due to velocity
loop response delay can be reduced.
Velocity
Feed-forward
feed-forward
Velocity compensation Torque

+ amount + compensation
+ + Velocity control +
Position control
Position Velocity Current
-
command command command
Position feedback
- 110 -
The following figure shows the effect of the feed-forward function.

The figure indicates that an arc radius error of 250 µm, which was
measured before the use of the feed-forward function, has been
reduced to almost 0 after the use of the feed-forward function.
Feed-forward coefficient 0% Feed-forward coefficient 100%
Radius error is about Radius error is

250 µm almost 0 µm
(b) Adjusting the feed-forward coefficient

The feed-forward coefficient can be adjusted on the screen shown
below. Note that, however, setting the feed-forward coefficient to
more than 10000 (100%) means that the actual machine position
advances ahead of commands from the CNC. So, such setting is not
permitted.
[Parameter window main screen] [Contour error suppression + feed-forward]
While checking fluctuation of radius by using an arc with about

R10/F4000 or R100/F10000 set, make an adjustment so that the actual
path matches the commanded path. At this time set the velocity
feed-forward coefficient to about 100.
NOTE
To fine-tune the amount of arc radius, also adjust
the feed-forward timing parameter after adjusting
the feed-forward coefficient. (See Subsection
4.6.5.)
- 111 -
(c) Adjusting backlash acceleration

To reduce quadrant protrusions (errors generated where the axis move
direction is reversed), the backlash acceleration function is used.
While observing the quadrant protrusion size, change the backlash
acceleration value in steps of about 10 to 20, and ends the adjustment
immediately before undercut occurs. A large quadrant protrusion or
undercut may adversely affect cutting results. So, adjust the backlash
acceleration so that any quadrant protrusion is not greater than 5 µm.
NOTE
1 For the adjustment of the conventional backlash
acceleration function, see Subsection 4.6.6.
2 When higher precision is required, use the 2-stage
backlash acceleration function (see Subsection
4.6.7).
[Parameter window main screen] [Contour error suppression + backlash acceleration]
- 112 -
(9) Adjustment by using a square figure (adjustment of the high-speed and

high-precision function and adjustment of the servo function)
(a) Setting the corner deceleration function
When the automatic corner deceleration function is used, an error at
the corner (overshoot) can be reduced. First, set the reduced corner
feedrate to 400 mm/min.
[Parameter window main screen] [Acc./dec. + AI contour control 2 (when AI contour

control II is used)]
The figure below shows the effect of the corner deceleration function.
Deceleration at a corner reduces the amount of the overshoot.
20µm 20µm
Axis Axis
movement movement
NOTE
For fine-adjustment of a corner overshoot, the
following parameters are also related:
• Acc./dec. before interpolation
• Velocity feed-forward coefficient
- 113 -
(b) Adjusting the time constant in cutting feed

In automatic corner deceleration, the feedrate at which the tool moves
along a corner is reduced according to the permissible acceleration set
for acc./dec. before interpolation. When the automatic corner
deceleration function is used, the tangential feedrate at the corner
changes in a V-shaped manner as shown below. As the permissible
acceleration for acc./dec. before interpolation is decreased,
deceleration at the corner becomes smoother, therefore, the contour
error at the corner can be decreased.
D A
Y
Position path
C B
Linear part
F3000 Feedrate along X-axis
F3000
A B C D
A B C D
Feedrate along Y-axis
Corner: F500
Tangential feedrate indication Indication of feedrate along each axis
[Parameter window main screen] [Acc./dec. + AI contour control 2 (when AI

contour control II is used)]
If the contour error at the corner cannot be reduced even by adjusting

the permissible feedrate difference, increase the time constant of
acc./dec. before interpolation.
When bell-shaped Acc/Dec. before interpolation is used, contour
errors not only at corners but also rounded corners may be improved.
Note that, however, a larger time constant extends the total machining
time.
- 114 -
(c) Adjusting velocity feed-forward

The velocity feed-forward function has the effect of helping the torque
command start earlier at the time of acc./dec. This effect is reflected in
corner figures. So, adjust the velocity feed-forward coefficient so that
corner figures can be improved. When nano interpolation is not used,
set the coefficient value to 400 or smaller.
[Parameter window main screen] [Contour error suppression + feed-forward]
- 115 -
(10) Adjustment by using a square figure with 1/4 arcs (adjustment of the
high-speed and high-precision function and adjustment of the servo
function)
When acceleration changes suddenly at an arc part, positional
deviation occurs. To reduce this positional deviation, set the
permissible acceleration. Hence, the feedrate is changed depending on
whether the tool moves along a linear part or an arc part in a square
figure with 1/4 arcs as shown below. In this example, the feedrate
decreases to F1000 in an arc part, and after the arc part is passed, the
feedrate increases to restore F4000. The acc./dec. before and after an
arc is determined by the time constant of acc./dec. before
interpolation.
D A
Figure
X
C B
Linear part: F4000

X-axis velocity command
F4000
F4000
A B C D
A B C D
Y-axis velocity command
Arc part: F1000
Target velocity command Velocity command (each axis)
The following figure shows that this function reduces the positional
deviation.
F4000 F4000
F2000
F4000
10µm error 10µm error
- 116 -
[Parameter window main screen] [Acc./dec. + AI contour control 2 (when AI

contour control II is used)]
When advanced preview control is used, the feedrate at a rounded

portion is suppressed by setting the arc radius and feedrate. For
example, when the arc radius is 5 mm, and the feedrate is to be
decreased to F2000, set R to 5 mm, and the feedrate to F2000
mm/min.
[Parameter window main screen] [Acc./dec. + advanced preview control (when

advanced preview control is used)]
- 117 -
The positional deviation in an arc part can be suppressed also by

adjusting the velocity feed-forward coefficient. Since the positional
deviation in an arc part is caused by velocity loop delay at the start
and end of the arc, velocity feed-forward, which compensates for
delay, is effective in the suppression of the positional deviation in arc
parts.
Positional
deviation due to
delay on Y-axis
Positional
Y deviation due to Y
delay on X-axis
X X
Velocity feed-forward disabled Velocity feed-forward enabled
- 118 -
3.3.2 High-speed Positioning Adjustment Procedure
(1) Overview
This section describes the adjustment procedure for high-speed
positioning required with a punch press and PC board drilling
machine.
(2) Adjustment procedure

Make a high-speed positioning adjustment while viewing the ERR
(servo error amount) and TCMD. Set a measurement range as
described below.
• ERR: Adjust the measurement range so that the precision
required for positioning can be seen. When using the
analog check board, measure VCMD instead of ERR.
(Adjust the VCMD magnification and the measurement
voltage level.) In the example below, a requested
precision of 10 µm is assumed.
• TCMD: Make an adjustment to view a specified maximum
current value. If an adjustment is made to reduce
positioning time, TCMD saturation may occur. Make
an adjustment so that the TCMD lies within a specified
maximum current.
<1> I-P function setting
Select I-P function for velocity loop control. In general, PI
function reduces start-up time for a command, but requires a
longer setting time, so that PI function is not suitable for
high-speed positioning. On the other hand, I-P function reduces
time required to reach a target position, so that I-P function is
generally used for high-speed positioning adjustment.
ERR ERR
Specified maximum current
20µm
300ms 270ms
TCMD TCMD
Fig. 3.3.2 (a) When PI function is used Fig. 3.3.2 (b) When I-P function is used
- 119 -
<2> Set a highest possible velocity loop gain according to Subsec.

3.3.1, "Servo HRV Control Adjustment Procedure."
ERR
TCMD fluctuation TCM D

is eliminated.
Fig. 3.3.2(c) After velocity loop gain adjustment
<3> Set a switch speed of 1500 (15 min-1) with the position gain
switch function (see Subsec. 4.8.1).
ERR
ERR
240 m s
270 m s
TCMD TCM D
Fig. 3.3.2(d) Position gain switch function
<4> Set a highest possible position gain. While viewing the ERR
waveform (VCMD waveform), make an adjustment so that the
overshoot value lies within a requested precision. After setting a
position gain, perform rapid traverse for a long distance to check
that low-frequency vibration due to an excessively increased
position gain does not occur. If the set position gain is too high,
vibration after an overshoot exceeds a requested precision. An
overshoot itself can be suppressed to some extent by adjustment
of <5>.
A large vibration occurs in a
ERR return movement. Suppress the
vibration to within 50% of the
requested precision.
20 µm
200 m s
TCM D
When a precision of 10 µm is If the position gain is too high,

requested, adjust the overshoot value the requested precision 10 µm is
to within 10 µm. exceeded.
Fig. 3.3.2(e) Adequate position gain Fig. 3.3.2(f) Excessively high position gain
- 120 -
<5> Make a fine PK1V adjustment to eliminate an overshoot and

undershoot. If a large value is set for PK1V, a large undershoot
occurs.
ERR ERR
20 µm
210 m s
TCM D
TCMD
When the value of PK1V is When the value of PK1V is increased
increased, the amount of an excessively, the amount of an
overshoot decreases. undershoot increases.
Fig. 3.3.2(g) After PK1V adjustment Fig. 3.3.2(h) When the value of PK1V is too large
- 121 -
3.3.3 Rapid Traverse Positioning Adjustment Procedure
(1) Overview
The fine acc./dec. function applies a filter to each axis in the servo
software to reduce a shock associated with acc./dec. By combining the
fine acc./dec. function with feed-forward, high-speed positioning can
be achieved in rapid traverse. This section describes rapid traverse
positioning adjustment.
NOTE
1 With the Series 30i, smooth acc./dec. is performed
based on nano interpolation even during rapid
traverse, so that fine acc./dec. is unnecessary
(unusable). For adjustment, only rapid traverse
bell-shaped acc./dec. is used. With the Series 30i,
rapid traverse bell-shaped acc./dec. is a basic
function.
2 With the Series 16i and so forth, nano interpolation
is not applied during rapid traverse, so that the use
of fine acc./dec. for smoothing command execution
is effective. With the Series 16i, rapid traverse
bell-shaped acc./dec. is an optional function.
(2) High-speed positioning by a combination of fine acc./dec. and

feed-forward
(Rapid traverse positioning when fine acc./dec. is not used)
A servo loop not performing feed-forward has a delay equivalent to a
position loop gain. The time required for positioning after completion
of distribution from the CNC is four to five times the position gain
time constant (33 ms for 30 [1/s]) (133 to 165 ms for a position gain of
30). In normal rapid traverse, rapid traverse linear acc./dec. (Fig. 3.3.3
(a)) is used, so that acceleration changes to a large extent at the start
and end of acceleration. However, since feed-forward is not used,
acceleration change is made moderate by a position loop gain, and a
shock does not occur.
If a low linear acc./dec. time constant is set for high-speed positioning,
and a high position gain and feed-forward are set, the time required
for positioning is reduced, but a shock occurs. In this case, a shock can
be reduced by setting rapid traverse bell-shaped acc./dec. (Fig. 3.3.3
(a)).
- 122 -
Rapid traverse linear time constant Rapid traverse bell-shaped Rapid traverse bell-shaped acc./dec.
(T1) only acc./dec. (T1+ T2) (T1+ T2) + nano
Feedrate (Series30i)
Feedrate
Feedrate
Acceleration
change is large, Acceleration change is
Acceleration change reduced by bell-shaped
so a shock is reduced by
tends to occur. acc/dec. and command
bell-shaped acc./dec. execution is smoothed
by nano interpolation.
T1 Time T1+T2
Time Time
T1+T2
Fig. 3.3.3 (a) Rapid traverse acc./dec. pattern and shock
(Rapid traverse positioning when fine acc./dec. is used)

Other than Series 30i
For further reduction in the time required for rapid traverse
positioning, a delay due to position gain needs to be minimized. For
this purpose, feed-forward needs to be fully utilized. When
feed-forward is applied, the positional deviation decreases.
Accordingly, positional deviation convergence occurs more rapidly
after distribution, thus reducing the time required for positioning.
If feed-forward close to 100% is applied to normal acc./dec. (Fig.
3.3.3 (a)), a mechanical shock due to acceleration change at the start
and end of acc./dec., and a torque command vibration during acc./dec.
can pose a problem. To cope with this, the fine acc./dec. function is
available (Fig. 3.3.3 (b) and (c)).
FAD (Tf ≤ 64 ms) is used. Rapid traverse bell-shaped acceleration/deceleration
(T2 > 64 ms) is used as well..
Feedrate Compared with linear If a second time constant
Feedrate
acceleration/deceleration, greater than 64 ms is
acceleration change is required, rapid traverse
reduced, and a smooth bell-shaped acceleration/
curve results. The time deceleration is used. The
required for positioning curve is made smooth by
can be reduced by inserting linear-type FAD of 8
feed-forward. ms.
Time Time
T1 + Tf
T1 + T2 + Tf
Fig. 3.3.3 (b) Fine acc./dec. (FAD) Fig. 3.3.3 (c) Rapid traverse bell-shaped acc./dec. + FAD
Fine acc./dec. increases the time required for command distribution by

a time constant. However, a time reduction in positioning achieved by
feed-forward is greater than this increase, so the time required for
positioning can be reduced in total. Thus, positioning can be speeded
up using fine acc./dec. The adjustment procedure is described in (3)
below.
(T1 + positioning time based on a position gain)
> (T1 + Tf + positioning time based on feed-forward)
A time constant up to 64 ms can be set for fine acc./dec. If a time
constant greater than 64 ms is required, use rapid traverse bell-shaped
acc./dec., and set 8 ms for linear-type fine acc./dec. (Fig. 3.3.3 (c)).
- 123 -

Make a rapid traverse positioning adjustment while viewing the ERR
(servo error amount). Adjust the measurement range so that the time
required for position deviation convergence within the in-position
width can be seen. At the same time, observe the TCMD to check that
the TCMD is not saturated. Before proceeding to the adjustment
described below, adjust the velocity loop gain according to item (5),
“Adjustment of high-speed velocity control” in the Subsec. 3.3.1,
"Gain Adjustment Procedure."
The measurement data of Fig. 3.3.3 (d) has been obtained under the
condition below. Fine acc./dec. and feed-forward are not used.
• Rapid traverse rate: 20000 mm/min
• Rapid traverse time constant: 150 ms
• Position gain: 30/s
• Travel distance: 100 mm
When the in-position width is 20 pulses, a time of about 180 ms is
required from distribution completion to positioning. Reducing this
time can speed up positioning.
Command from
the CNC Positional
deviation
In-position width
Servo delay time of

about 180 ms
Fig. 3.3.3 (d) Measurement of time before adjustment
<1> Default parameter setting for fine acc./dec. and feed-forward

Set the parameters according to Table 3.3.3. By setting the
default parameters, the time required for positioning can be much
reduced.
Table 3.3.3 Default parameters for rapid traverse positioning adjustment

Default parameter
Item Series16i and
Series15i Series30i Setting
so on
Rapid traverse feed-forward enable No1800#3 No1800#3 No1800#3 1
Fine acc./dec. function enable No1951#6 No2007#6 - 1
Linear-type fine acc./dec. No1749#2 No2009#2 - 1
Fine acc./dec. time constant No1702 No2109(*1) - 40
Feed-forward enable No1883#1 No2005#1 No2005#1 1
Feed-forward coefficient No1985 No2092(*1) No2092(*1) 9700
Velocity feed-forward coefficient No1962 No2069(*1) No2069(*1) 100
*1 When using different values for cutting and rapid traverse,

use the cutting feed/rapid traverse switchable fine acc./dec.
function according to Section 4.3, "CUTTING
FEED/RAPID TRAVERSE SWITCHABLE FUNCTION."
- 124 -
<2> Velocity feed-forward adjustment

When feed-forward is enabled, the time required for positioning
can be reduced, but a swell may occur due to insufficient velocity
loop response immediately before machining stops. A swell can
be reduced by an increased velocity loop gain, but there is an
upper limit on the velocity loop gain. So, adjust the velocity
feed-forward coefficient to reduce a swell for positioning time
reduction.
The default settings cause a swell immediately before machining
stops (Fig. 3.3.3 (e)). The swell can be reduced by increasing the
velocity feed-forward coefficient (Fig. 3.3.3 (f)).
A swell is
observed An optimum is
immediately achieved
before when the
machining stops. swell here is
reduced.
Fig. 3.3.3 (e) Before velocity feed-forward Fig. 3.3.3 (f) After velocity feed-forward
adjustment adjustment
FAD: 64 ms FAD: 64 ms
Feed-forward: 98.5% Feed-forward: 98.5%
Velocity feed-forward coefficient: 100% Velocity feed-forward coefficient: 250%
<3> Fine adjustment of feed-forward

Reduce the time required for positioning by making a fine
adjustment of the feed-forward coefficient. If the feed-forward
coefficient is not sufficiently large (Fig. 3.3.3 (g)), increase the
feed-forward coefficient by about 0.5%. If the feed-forward
coefficient is too large (Fig. 3.3.3 (h)), decrease the feed-forward
coefficient by about 0.5%.
If the feed-forward If the position feed-forward

coefficient of the coefficient is too large, an
position loop is too overshoot occurs
small, an undershoot immediately before
occurs, resulting in a machining stops. If such
longer time. an overshoot is allowed
from the viewpoint of
precision, the time required
for positioning is reduced.
Fig. 3.3.3 (g) When the feed-forward coefficient Fig. 3.3.3 (h) When the feed-forward coefficient
is too small is too large
FAD: 64 ms FAD: 64 ms
Feed-forward: 98% Feed-forward: 99%
Velocity feed-forward coefficient: 250% Velocity feed-forward coefficient: 250%
- 125 -
If an adequate feed-forward coefficient is set, the in-position

width is satisfied nearly at the same as distribution command
completion, and shortest-time positioning is achieved as shown
in Fig. 3.3.3 (i).
Optimal
adjustment in
precision and time
Fig. 3.3.3 (i) When an adequate feed-forward coefficient is set

FAD: 64 ms
Feed-forward: 98.5%
Velocity feed-forward coefficient: 250%
- 126 -
3.3.4 Vibration in the Stop State

Vibration generated only in the stop state is caused by the decreased
load inertia in a backlash. Adjust the auxiliary functions for
suppressing stop-time vibration. Vibration may be generated only in
the stop state also when the position gain is too large.
<1> Is an auxiliary function set to increase the oscillation limit for the velocity loop gain?
Machine with high rigidity: Velocity loop proportional high-speed processing function (function 1)
Machine with low rigidity: Acceleration feedback function (function 2)
<2> Is an auxiliary function set to suppress vibration in the stop state?

Function for changing the proportional gain in the stop state (50%, 75%, arbitrary) (function 3)
N pulse suppression function (function 4)
<3> Vibration frequency?
Several tens of hertz or higher Low frequency

<4> Decrease the velocity loop gain. When using the <5> The position gain may be too large for the
cutting feed/rapid traverse velocity loop gain velocity loop gain. (Vibration is sometimes
switch function, decrease the velocity loop gain for generated when the load inertia is too high or
rapid traverse. when the velocity loop gain is not yet adjusted.)
<6> When the velocity loop gain is not adjusted,

follow the description in Subsec. 3.3.1 to set the
velocity loop gain to 70% of the oscillation limit.
<7> Decrease the position gain.
(Reference: Parameter numbers)

For details, see Chapter 4, "SERVO FUNCTION DETAILS."
Function 1: Velocity loop proportional high-speed processing

function
#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) PK2V25
2017 (FS30i, 16i)
PK2V25 (#7) 1: Enables the velocity loop proportional high-speed processing
function.
Function 2: Acceleration feedback

1894 (FS15i) Acceleration feedback gain
2066 (FS30i, 16i)
- 127 -
Function 3: Function for changing the proportional gain in the stop

state
#7 #6 #5 #4 #3 #2 #1 #0
1958 (FS15i) PK2VDN
2016 (FS30i, 16i)
PK2VDN (#3) 1: Enables the function for changing the proportional gain in the stop
state. In the stop state: 75%
#7 #6 #5 #4 #3 #2 #1 #0
1747 (FS15i) PK2D50
2207 (FS30i, 16i)
PK2D50 (#3) 1: Decreases the proportional gain in the stop state to 50%.
1730 (FS15i) Stop decision level

2119 (FS30i, 16i)
2737 (FS15i) Function for changing the proportional gain in the stop state:
Arbitrary magnification in the stop state (during cutting feed only)
2324 (FS30i, 16i)
Function 4: N pulse suppress function
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) NPSP
2003 (FS30i, 16i)
NPSP (#4) 1: Uses the N pulse suppress function.
- 128 -
3.3.5 Vibration during Travel

Vibration is generated during travel by various causes. So, a most
appropriate method must be selected after observing the vibration
status carefully.
<1> Is an auxiliary function set to increase the oscillation limit for the velocity loop gain?
Machine with high rigidity: Velocity loop proportional high-speed processing function
Machine with low rigidity: Acceleration feedback function
<2> Vibration frequency?

Several tens of Vibration occurs especially
hertz or higher About several tens Hertz Low frequency during acceleration/
with separate detector deceleration.
<3> Velocity loop oscillates. Is an auxiliary function <8> Response to vibration components from the
used to suppress vibration? command side. Decrease the velocity
TCMD filter (function 1) feed-forward coefficient (200 or less).
<4> Is the standard value set for the current loop <9>
gain? Series30i: Increase the time constant after
interpolation.
Series16i and so on:
Set 16 ms for the fine acc./dec.
<5> Decrease the velocity loop gain.
function. (Function 5)
<6> Vibration may be due to machine torsion. Is an <11> The position gain may be too large for the set
auxiliary function used to suppress vibration? velocity loop gain. When the velocity loop gain
- Dual position feedback (function 2) is not yet adjusted, follow the description in
- Vibration-damping control (function 3) Subsec. 3.3.1 to set the velocity loop gain to
- Machine velocity feedback (function 4) 70% of the oscillation limit.
- TCMD filter (function 1)
<12> For PI function, are effective results produced

<7> Decrease the position gain. by decreasing the velocity loop integral gain by
Use of I-P function may produce effective results. about 2/3?
After checking for a figure error during high-speed
cutting, decrease the position gain, or set I-P function.
<13> Decrease the position gain.
- 129 -

Function 1: TCMD filter
1895 (FS15i) TCMD filter coefficient

2067 (FS30i, 16i)
Function 2: Dual position feedback function

#7 #6 #5 #4 #3 #2 #1 #0
1709 (FS15i) DPFB
2019 (FS30i, 16i)
DPFB (#7) 1: Enables dual position feedback.
1971 (FS15i) Dual position feedback: conversion coefficient (numerator)

2078 (FS30i, 16i)
1972 (FS15i) Dual position feedback: conversion coefficient (denominator)

2079 (FS30i, 16i)
1973 (FS15i) Dual position feedback: primary delay time constant

2080 (FS30i, 16i)
Function 3: Vibration-damping control
1718 (FS15i) Vibration-damping control function: number of position feedback pulses

2033 (FS30i, 16i)
1719 (FS15i) Vibration-damping control function: gain

2034 (FS30i, 16i)
Function 4: Machine velocity feedback

#7 #6 #5 #4 #3 #2 #1 #0
1956 (FS15i) MSFE
2012 (FS30i, 16i)
MSFE (#1) 1: Enables machine velocity feedback.
1981 (FS15i) Machine velocity feedback gain

2088 (FS30i, 16i)
Function 5: Fine acc./dec. function

#7 #6 #5 #4 #3 #2 #1 #0
1951 (FS15i) FAD
2007 (FS16i)
FAD (#6) 1: Enables fine acc./dec.
1702 (FS15i) Fine acc./dec. time constant

2109 (FS16i)
- 130 -
NOTE
In the Series 30i, 31i, and 32i, smooth acc./dec. is
always performed by nano interpolation, so the fine
acc./dec. function is ignored.
3.3.6 Stick Slip

When the time from the detection of a position error until the
compensation torque is output is too long, a stick slip occurs during
low-speed feed. Improvement in gain is required. However, for a
machine with high friction and torsion, a higher gain cannot be set. In
such a case, a stick slip phenomenon may occur.
<1> Adjust the position gain and velocity loop gain

according to the description in Subsec. 3.3.1.
<2> Set PI function.
<3> To improve torque start, increase the velocity

loop integral gain.
<4> Set the VCMD offset function. (Function 1)
<5> Set the incomplete integral coefficient within the

range 32700 to 32767 (function 2). For axes subject
to interpolation, this coefficient must not be set.

Function 1: VCMD offset function

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) VOFS
2003 (FS30i, 16i)
VOFS (#7) 1: Enables the VCMD offset function.
1857 (FS15i) Incomplete integral gain

2045 (FS30i, 16i)
- 131 -
3.3.7 Overshoot
When the machine is operated at high speed or with a detection unit of
0.1 µm or less, the problem of overshoots may arises. Select a most
appropriate preventive method depending on the cause of the
overshoot.
<1> When the velocity loop gain is not yet adjusted,
follow the description in Subsec. 3.3.1 to adjust
the gain. Select PI function.
<2> When advanced preview control is used, adjust

automatic corner deceleration. Also, increase
settings such as the time constant after
interpolation to allow commands for corner and
stop operations to be executed as moderately as
possible.
<3> When feed-forward is used, try to adjust the

velocity feed-forward coefficient.
<4> Where possible, decrease the position gain and

feed-forward coefficient.
<5> If the overshoot in question is for about one or

two pulses, set overshoot compensation
(TYPE-1 or -2). (Function 1)

Function 1: Overshoot compensation function

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) OVSC
2003 (FS30i, 16i)
OVSC (#6) 1: Enables the overshoot compensation function.
1970 (FS15i) Overshoot prevention counter

2077 (FS30i, 16i)
1857 (FS15i) Incomplete integral coefficient

2045 (FS30i, 16i)
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) OVS1
2202 (FS30i, 16i)
OVS1 (#3) 1: Enables overshoot compensation TYPE-2.
- 132 -
B-65270EN/07 4.SERVO FUNCTION DETAILS
4 SERVO FUNCTION DETAILS

Chapter 4, "SERVO FUNCTION DETAILS", consists of the
following sections:
4.1 SERVO HRV CONTROL......................................................134

4.2 HIGH-SPEED HRV CURRENT CONTROL........................138
4.3 CUTTING/RAPID SWITCHING FUNCTION .....................150
4.4 VIBRATION SUPPRESSION IN THE STOP STATE .........156
4.5 MACHINE RESONANCE ELIMINATION FUNCTION ....168
4.6 CONTOUR ERROR SUPPRESSION FUNCTION ..............202
4.7 OVERSHOOT COMPENSATION FUNCTION...................251
4.8 HIGH-SPEED POSITIONING FUNCTION .........................257
4.9 SERIAL FEEDBACK DUMMY FUNCTIONS ....................272
4.10 BRAKE CONTROL FUNCTION..........................................276
4.11 QUICK STOP FUNCTION....................................................280
FUNCTIONDISTURBANCE TORQUE DETECTION........296
4.13 FUNCTION FOR OBTAINING CURRENT OFFSETS AT
EMERGENCY STOP.............................................................311
4.14 LINEAR MOTOR PARAMETER SETTING .......................312
4.15 SYNCHRONOUS BUILT-IN SERVO MOTOR
PARAMETER SETTING ......................................................346
4.16 SETTING PARAMETERS FOR LARGE SERVO
MOTORS ...............................................................................388
4.17 INTERACTIVE FORCE COMPENSATION FUNCTION...398
4.18 TORQUE CONTROL FUNCTION .......................................415
(POSITION TANDEM) (Optional Function) ........................418
4.20 SYNCHRONOUS AXES AUTOMATIC
COMPENSATION.................................................................426
4.21 TORQUE TANDEM CONTROL FUNCTION (Optional
Function).................................................................................430
4.22 SERVO TUNING TOOL SERVO GUIDE............................455
- 133 -
4.SERVO FUNCTION DETAILS B-65270EN/07
4.1 SERVO HRV CONTROL
(1) Overview
Servo HRV control is a digital servo control system based on
high-speed, high-response current control and includes servo HRV1
control, servo HRV2 control, servo HRV3 control, and servo HRV4
control. Use of these control systems allows higher acceleration,
higher speed, and higher precision.
Servo HRV control system

Servo HRV1 control
Servo HRV control Servo HRV2 control

Servo HRV3 control
Servo HRV4 control
(2) Servo HRV control and Series and editions of applicable servo software
Series30i Other than the Series 30i
Series 90D0/A(01) Series 90E0/A(01) and Series 90B0H(08) and Series 9096/A(01)
and subsequent subsequent editions subsequent editions and subsequent
editions (Note 2) Series 90B1A(01) and editions
(Note 1, 2) subsequent editions
Series 90B5A(01) and
subsequent editions
subsequent editions
subsequent editions
Servo HRV1 control × × ○ ○
Servo HRV2 control ○ ○ ● ×
Servo HRV3 control ○ ● ○ ×
Servo HRV4 control ● × × ×
○: Supported (● is recommended)
×: Not supported
NOTE
1 When using servo HRV4 control, use Series
90D0/J(10) and subsequent editions.
2 For Series 90D0 and 90E0, apply the same servo
HRV control to all axes.
- 134 -
(3) Features of servo HRV control

(a) Servo HRV2 control
Servo HRV control is a total control technology implemented by a
servo motor, servo amplifier, and control systems as shown in the
figure below. Servo HRV2 control has the following features:
(1) HRV filters for eliminating vibration components of the machine
system can be used.
The HRV filters include the following filters to cover a wide
range of vibration from low frequency vibration to high
frequency vibration:
TCMD filter (a filter for eliminating middle frequency vibration)
Resonance elimination filter (a filter for eliminating high
frequency vibration)
Disturbance elimination filter (a filter for eliminating low
frequency vibration)
(2) Use of a αiS/αiF/βiS series motor and a αi/βi servo amplifier
enables high-speed, high-precision, and smooth feed.
(3) Use of a precise pulse coder improves control performance.
With Series 90B0, 90B1, 90B5, 90B6, and 90B8, it is recommended

that servo HRV2 control is used for the current loop.
Capable of handling low-frequency Exercises current control Detects
vibration to high-frequency vibration at high speed. current with
high precision.
Position Velocity HRV filter HRV current Servo

control control control amplifier
Current feedback
Velocity feedback
High-response, high-precision detector
(b) Servo HRV3 control

In addition to the features of HRV2 control, servo HRV3 control has
the following features:
(1) Use of high-speed DSP enables high-speed HRV current control,
therefore improving the response performance of the current
loop.
(2) When a linear motor or an αiS series servo motor are used, both
high acceleration, high speed and high precision can be provided
at the same time.
With Series 90E0, use of servo HRV3 control is recommended.
- 135 -
(c) Servo HRV4 control

In addition to the features of servo HRV2 and servo HRV3, servo
HRV4 control has the following features:
(1) An improved servo HRV control system is employed. (Extended
HRV function)
(2) Improved thermal resistance in the high-speed DSP and servo
amplifier provides the current loop with higher response
performance than the response performance provided by servo
HRV3 control.
Series 90D0 is required to use servo HRV4 control.
- 136 -
4.1.1 Servo HRV2 Control

(Series 15i-B,16i-B,18i-B,21i-B,0i-B,0i Mate-B, Power Mate i)
(2) Setting the parameters for servo HRV2 control

<1> Set a motor ID number for HRV2 control.
(For a motor ID number, see (3) of Subsection 2.1.3.)
<2> Set initialization bit 1 to 0 then turn off the power to the CNC
then turn on the power again.
<3> The standard parameters for servo HRV2 control are
automatically loaded.
<4> Completion of setting
NOTE
For servo parameter initialization, see Subsection
2.1.3.
- 137 -
4.2 HIGH-SPEED HRV CURRENT CONTROL

(Series 15i-B,16i-B,18i-B,21i-B,0i-B)
(2) Setting parameters for servo HRV3 control

<1> See Subsection 4.1.1, and make settings for servo HRV2 control.
<2> Set servo HRV3 current control. (For each axis)

#7 #6 #5 #4 #3 #2 #1 #0
1707(FS15i) HR3
2013(FS30i,16i)
HR3(#0) 0: Does not use servo HRV3 control.
1: Uses servo HRV3 control.
NOTE
When servo HRV3 control is used with Series
90E0, a multiple of 4 cannot be set in parameter
No. 1023. Skip multiples of 4 when setting the
parameter.
Example: when using eight axes with Series 90E0,
set parameter No. 1023 as follows:
1,2,3,5,6,7,9,10
<3> Set the cutting/rapid velocity loop gain switching function.

#7 #6 #5 #4 #3 #2 #1 #0
1742(FS15i) VGCCR
2202(FS30i,16i)
VGCCR (#1) 0: Does not use the cutting/rapid velocity loop gain switching
function.
1: Uses the cutting/rapid velocity loop gain switching function.
- 138 -
<4> Set the current loop gain magnification.

2747(FS15i) Current loop gain magnification in high-speed HRV current control mode
2334(FS30i,16i)
[Unit of data] %
[Recommended value] 150
This parameter is valid only for cutting feed in the high-speed HRV
current control mode.
<5> Set the velocity loop gain magnification.

2748(FS15i) Velocity loop gain magnification in high-speed HRV current control mode
2335(FS30i,16i)
[Unit of data] %
1700(FS15i) Velocity loop gain magnification for cutting (cutting/rapid velocity loop gain switching)
2107(FS30i,16i)
[Unit of data] %
This parameter is valid only for cutting feed when the high-speed
HRV current control mode is not set.
<6> Set the high-speed HRV current control mode.

To use servo HRV3 control with servo software Series 90D0 and
90E0 for the Series 30i, 31i, and 32i, set the following bit, which
automatically sets the high-speed HRV current control mode
during cutting feed:
#7 #6 #5 #4 #3 #2 #1 #0
- NOG54
2283(FS30i,31i,32i)
NOG54(#0) The high-speed HRV current control mode (servo HRV3 control) is:
0: Set only when both G5.4Q1 and G01 are specified.
1: Set when G01 is specified (G5.4Q1 is not monitored).
NOTE
This function cannot be used during servo HRV4
control.
<7> This completes parameter setting. To actually enter the

high-speed HRV current control mode, G codes must be
programmed. (This is not required if NOG54 is set to 1. See
Subsection 4.2.3.)
NOTE
The velocity loop gain is changed as listed below
according to whether the high-speed HRV current
control mode is set or not.
- 139 -
[Series30i,16i, and so on]

High-speed HRV
Feed Velocity loop gain [%]
current control mode
Rapid traverse (1 + No. 2021 / 256) × 100
Set
（G5.4Q1 - G5.4Q0） (1 + No. 2021 / 256) × No. 2335
Cutting feed
(High-speed HRV current control: Velocity loop gain magnification)
Not set (1 + No. 2021 / 256) × No. 2107
Cutting feed
(Cutting/rapid switching: Velocity loop gain magnification)
[Series15i]
High-speed HRV
Set
（G5.4Q1 - G5.4Q0） (1 + No. 1875 / 256) × No. 2748
Cutting feed
Not set (1+No1875 / 256) × No. 1700
Cutting feed
(3) Limitation on servo HRV3 control

(a) Servo motor output torque
(Series 90B0, 90B1, 90B5, 90B6, 90B8)
During cutting operation in high-speed HRV current control, the
torque command is automatically limited to 70% of the maximum
current value of the servo amplifier. As a result, the torque command
is easily saturated. Therefore, when determining the time constant in
cutting feed, consider the cutting load and the above limitation.
Normally, the high-speed HRV current control mode is used for light
cutting for finish machining, so the limitation of the torque command
to 70% of the maximum current value of the servo amplifier is not
regarded as critical.
Torque curve during G5.4Q1 command
Maximum output
torque of servo motor At rapid traverse in HRV2 or HRV3
100%
70%
At cutting in HRV3 (G5.4Q1)
Feedrate
(Series 90D0, 90E0)

The servo amplifiers supporting the Series 30i and so on have
advanced thermal resistance. So, unlike Series 90B0, 90B1, 90B5,
90B6, and 90B8, there is no torque command limitation.
- 140 -
(4) Servo HRV3 control hardware

(a) Separate detector
(Series 90B0, 90B1, 90B5, 90B6, 90B8)
When a separate detector is used for servo HRV3 control, the
following separate detector interface unit supporting servo HRV3
control must be specified:
Separate detector interface unit for
Specification drawing number
servo HRV3 control
Basic 4 axes A02B-0236-C205
(Series 90D0, 90E0)

When a separate detector is used with the Series 30i and so on, the
following separate detector interface unit supporting the Series 30i
and so on must be specified:
Series 30i and other CNC
(b) Servo axis control cards

(Series 90B0, 90B1, 90B5, 90B6, 90B8)
Servo axis control cards are divided into two groups: type A and type
B.
Type A card: One optical connector is provided.
Type B card: Two optical connectors are provided.
Axis control card Axis control card
(Type-A) (Type-B)
Type A has one optical connector. Type B has two optical connectors.
When servo HRV3 control is used, up to four servo amplifier axes can
be connected to one optical connector, and only one separate detector
interface unit can be connected to one optical connector. When five or
more servo amplifier axes or two separate detector interface units are
to be connected, a type B card is required.
Maximum number of axes

Axis control card
HRV2 HRV3
Type A card 8 axes 4 axes
Type B card 8 axes 8 axes
Type A card: One optical connector is provided. (The maximum

number of axes is 8.)
Type B card: Two optical connectors are provided. (The maximum
number of axes is 8.)
NOTE
When four servo amplifier axes and one separate
interface unit are connected to one optical
connector, the separate detector interface unit
must be connected in the fifth position.
- 141 -
[Number of controlled axes]

When a type A card is used: Up to four servo HRV3 control axes
When a type B card is used: Up to eight servo HRV3 control axes
• When a type A card is used: Up to four axes plus one unit can
be connected.
FSSB-1
AMP AMP AMP AMP Separate
Axis control card (Optical detector
1 2 3 4 interface
(Type-A) cable)
unit 1
(Up to four axes)
• When a type B card is used: Up to eight axes plus two units can
be connected.
FSSB-1
Separate
AMP AMP AMP AMP detector
(Optical 1 2 3 4
cable) interface
unit 1
Axis control card
(Type-B)
FSSB-2
Separate
(Optical 5 6 7 8
cable) interface
unit 2
(Up to eight axes)
• (Reference) When servo HRV3 control is not used: With a type
A card, up to eight axes plus two units can be connected.
FSSB-1
AMP AMP AMP AMP AMP Separate Separate
Axis control card (Optical detector detector
cable) 1 2 3 4 8 interface
(Type-A) interface
unit 1 unit 2
(Series 90D0, 90E0)

There are two types of servo axis cards for Series 90D0 and 90E0:
type A and type B. There is a restriction on axes as follows:
(Type-A) (Type-B)
• Number of units that can be connected to one FSSB optical

connector
Separate detector
Servo HRV3 control is: Amplifier
interface unit
Used. (Note) 10 axes 2 units
Note used. 16 axes 2 units
• Numbers of units that can be connected to the servo cards

Series 90E0 Series 90E0 Series 90D0 Separate
Servo card servo HRV2 servo HRV3 servo HRV2, 3 detector
control control control interface unit
Servo card B13
A02B-0303-H084 Amplifier 12 axes Amplifier 9 axes Amplifier 6 axes 2 units
(Type-A card)
Servo card B26
A02B-0303-H085 Amplifier 24 axes Amplifier 18 axes Amplifier 12 axes 4 units
(Type-B card)
- 142 -
NOTE
1 When 10 or more servo amplifier axes or three
separate detector units are used with servo HRV3
control, the Type-B card is required.
2 When 13 or more servo amplifier axes or five
separate detector interface units are used without
servo HRV3 control, the Type-B card is required.
3 For the maximum number of controlled axes, refer
to "FANUC Series 30i CONNECTION MANUAL
(HARDWARE) (B-63943EN)".
• When the Type-A card is used: Up to nine axes plus two units
can be connected.
FSSB-1
Separate Separate
AMP AMP AMP AMP AMP detector detector
Axis control card (Optical
cable) 1 2 3 4 9 interface interface
(Type-A) unit 2
unit 1
• When the Type-B card is used: Up to 18 axes plus four units can
be connected.
FSSB-1
(Optical 1 2 3 4 10 detector detector
cable) interface interface
unit 1 unit 2
Axis control card
(Type-B)
FSSB-2 Separate
Separate
AMP AMP AMP AMP AMP detector
(Optical detector
unit 3 unit 4
• (Reference) When servo HRV3 control is not used:

With the Type-A card, up to 12 axes plus two units can be
connected.
With the Type-B card, up to 24 axes plus four units can be
connected.
FSSB-1
Separate Separate
Axis control card (Optical
(Type-A) unit 1 unit 2
FSSB-1
(Optical detector detector
1 2 3 4 16 interface
cable) interface
unit 1 unit 2
Axis control card
(Type-B)
FSSB-2
Separate Separate
(Optical 17 18 19 20 24
cable) interface interface
unit 3 unit 4
- 143 -

(Series 30i, 31i)
(2) Setting parameters for servo HRV4 control

<1> See Subsection 4.1.1, and make settings for servo HRV2 control.
<2> Set servo HRV4 control. (For each axis)
#7 #6 #5 #4 #3 #2 #1 #0
- HR4
2014(FS30i, 31i)
NOTE
1 When the high-speed HRV current control mode is
set by the G5.4Q1 command, servo HRV3 control
or servo HRV4 control, whichever set in a
parameter, is enabled. Therefore, both the servo
HRV3 control enable bit and the servo HRV4
control enable bit cannot be set to 1 at the same
time. (If these bits are both set to 1, an alarm
indicating invalid current control setting is issued.)
2 When servo HRV4 control is used with Series
90D0, multiples of 2 cannot be set in parameter
No. 1023. Set values with multiples of 2 skipped.
Example: When five axes are used with 90D0,
values 1,3,5,7,9 are set in parameter No.
1023.
3 If servo HRV4 control is set, servo HRV3 control is
performed during rapid traverse or when
high-speed HRV current control is disabled.
4 In servo HRV4 control using Series 90D0, one axis
is controlled with one CPU. So, functions (such as
tandem vibration-damping control during
synchronization control, and torque tandem control)
involving two or more axes in servo software
processing cannot be used.
<3> Enable the extended HRV function. (For each axis)
#7 #6 #5 #4 #3 #2 #1 #0
- HRVEN
2300(FS30i, 31i)
HRVEN(#0) 0: Does not use the extended HRV function.
1: Uses the extended HRV function.
- 144 -
<4> Set the cutting/rapid velocity loop gain switching function.

#7 #6 #5 #4 #3 #2 #1 #0
- VGCCR
2202(FS30i, 31i)
VGCCR (#1) 0: Does not use the cutting/rapid velocity loop gain switching
function.
1: Uses the cutting/rapid velocity loop gain switching function.
<5> Set the current loop gain magnification.

- Current loop gain magnification in high-speed HRV current control mode
2334(FS30i, 31i)
[Unit of data] %
<6> Set the velocity loop gain magnification.

- Velocity loop gain magnification in high-speed HRV current control mode
2335(FS30i, 31i)
[Unit of data] %
HRV current control mode is set.
- Velocity loop gain magnification (cutting/rapid velocity loop gain switching)

2107(FS30i, 31i)
[Unit of data] %
HRV current control mode is not set.
<7> This completes parameter setting. To actually enter the

high-speed HRV current control mode, G codes must be
programmed. (See Subsection 4.2.3.)
NOTE
The velocity loop gain is changed as listed below
according to whether the high-speed HRV current
control mode is set or not.
[Series 30i and so on]

High-speed HRV
Set
（G5.4Q1 - G5.4Q0） (1 + No. 2021 / 256) × No. 2335
Cutting feed
Not set (1 + No. 2021 / 256) × No. 2107
Cutting feed
- 145 -
(3) Limitation on servo HRV4 control

(a) Servo motor output torque
During cutting operation in high-speed HRV current control, the
torque command is automatically limited to 70% of the maximum
current value of the servo amplifier. As a result, the torque command
is easily saturated. Therefore, when determining the time constant in
cutting feed, consider the cutting load and the above limitation.
Normally, the high-speed HRV current control mode is used for light
cutting for finish machining, so the limitation of the torque command
to 70% of the maximum current value of the servo amplifier is not
regarded as critical.
Torque curve during G5.4Q1 command

Maximum output
torque of servo motor
t rapid traverse in HRV2 , HRV3, or HRV4
100%
70%
At cutting in HRV4 (G5.4Q1)
Feedrate
(4) Servo HRV4 control hardware

(a) Separate detector
When a separate detector is used with the Series 30i and so on, the
following separate detector interface unit supporting the Series 30i
and so on must be specified:
Series 30i and other CNC
(b) Servo amplifiers

A servo amplifier supporting servo HRV4 control must be specified.
- 146 -
(c) Servo axis control cards

There are two types of servo axis cards for Series 90D0 and 90E0:
Type-A and Type-B. There is a restriction on axes as follows:
(Type-A) (Type-B)
• Number of units that can be connected to one FSSB optical

connector
Servo HRV4 control is: Amplifier Separate detector interface unit
Used. (Note 1) 4 1
Not used. (Note 2)
• Numbers of units that can be connected to the servo cards

Series 90D0 servo Separate detector
Servo card
HRV4 control interface unit
Servo card B13
A02B-0303-H084 Amplifier 3 axes 1 unit
(Type-A card)
Servo card B26
A02B-0303-H085 Amplifier 6 axes 2 units
(Type-B card)
NOTE
1 When four or more servo amplifier axes or two
separate detector units are used with servo HRV4
control, the Type-B card is required.
2 See the description of the servo axis control cards
for servo HRV3 control.
• When the Type-A card is used: Up to three axes plus one unit
can be connected.
FSSB-1
Separate
AMP AMP AMP detector
Axis control card (Optical 1 2 3 interface
(Type-A) cable)
unit 1
• When the Type-B card is used: Up to six axes plus two units can
be connected.
FSSB-1
Separate
(Optical
cable) 1 2 3 4 interface
unit 1
Axis control card
(Type-B)
FSSB-2
Separate
AMP AMP detector
(Optical 5 6
cable) interface
unit 2
- 147 -
(d) Detector
To use servo HRV4 control, a detector supporting high-speed
communication needs to be used for motor feedback (as a detector on
the semi-closed loop side).
The table below indicates examples of detectors that support
high-speed communication.
If a setting is made to enable HRV4 when a detector not supporting

high-speed communication is connected, "SV0456 INVALID
CURRENT CONTROL PERIOD SETTING ALARM" is issued.
Table 4.2.2 (a) Sample configuration of a detector usable with HRV4

Manufacture Configuration or model
FANUC αi Pulse coder
FANUC αiCZ sensor (512A, 768A, 1024A)
FANUC Combination of high-resolution serial output circuit H with
an incremental scale supplied by a vendor other than
FANUC
FANUC Combination of high-resolution serial output circuit C with
an incremental scale supplied by a vendor other than
FANUC
HEIDENHAIN RCN827F, RCN727F, RCN227F, RCN223F, ECN223F,
LC493F, LC193F
MITUTOYO AT553, AT555, ST753
SAMTAK ATT270S
SONY RU77, SR77
NEWALL SHG-AF
* The table above indicates the configurations and models whose
support for high-speed communication is confirmed as of August,
2007. For details, contact the detector manufacturers.
- 148 -
4.2.3 High-Speed HRV Current Control
(1) Starting the high-speed HRV current control mode

The high-speed HRV current control mode is turned on and off by
using a G code (G5.4). The high-speed HRV current control mode is
set for cutting commands specified between G5.4Q1 and G5.4Q0.
High-speed HRV
(2) Checking the high-speed HRV current control mode
Diagnosis No. 700 is used for checking the status

of the high-speed HRV current control mode in
servo HRV3 control and servo HRV4 control.
After setting servo HRV3 or HRV4 control and
turning the power off then back on, check that bit
1 (HOK) of diagnosis No. 700 is set. When servo
HRV3 or HRV4 control can be used, HOK is set
to 1.
When HOK is set to 1, specifying G5.4Q1 sets

bit 0 (HON) of diagnosis No.700 to 1 during the
cutting feed command. If NOG54 is set to 1, bit 0
is set to 1 during the cutting feed command even
if G5.4Q1 is not specified.
When HON is set to 1, a high-speed current
control cycle is set, and the current gain
magnification for high-speed HRV current
control is applied.
- 149 -
4.3 CUTTING/RAPID SWITCHING FUNCTION
(1) Overview
Increasing the gains of the position loop and velocity loop is effective
in the improvement of cutting profiles. However, the maximum
feedrate and the acceleration of acc./dec. in rapid traverse are
generally higher than those in cutting feed. So, vibration in the
velocity loop or hunting in the position loop may occur in rapid
traverse even when stable cutting feed can be performed with the same
settings. To prevent this problem, the functions below are provided
with a function for switching between parameters for cutting feed and
parameters for rapid traverse.
Velocity feed
Feed forward forward
+ +
Fine acc./dec. Position + Velocity + TCMD filter
gain loop gain
Fig. 4.3 Parameters that can be switched between parameters for cutting feed and for rapid traverse
NOTE
1 The TCMD filter and resonance elimination filter
can be used at the same time by parameter setting.
2 The cutting/rapid switching function is not applied
to the resonance elimination filter.
(2) Setting procedure

(a) Switching of the velocity loop gain and fine acc./dec.
[Series and editions of applicable servo software]
- 150 -
<1> Cutting/rapid velocity loop gain switching function

When TCMD is saturated during acceleration in rapid traverse,
oscillation is easily generated in the velocity loop at the end of
acceleration in rapid traverse. In some machines, as the feedrate
becomes higher, high-frequency oscillation easily occurs. In such
cases, switching between the gain for cutting feed and the gain
for rapid traverse is effective.
If the cutting/rapid velocity loop gain switching is set, the
conventional velocity gain is used in rapid traverse, and the
overridden value is used during cutting feed. The override value
is usually set to about 150% to 200%. When vibration occurs
only in the stopped state, use the variable proportional gain
function in the stop state. (With Series 90D0, 90E0, 90B0, 90B1,
90B5, 90B6, and 90B8, the variable proportional gain function in
the stop state and the velocity loop high cycle management
function can be used together.)
When servo HRV3 control or HRV4 control is used, a separate
override value can be specified during high-speed HRV current
control. See Section 4.2, "HIGH-SPEED HRV CURRENT
CONTROL".
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) VGCCR
2202 (FS30i,16i)
0: Disables the cutting/rapid velocity loop gain switching function.
1: Enables the cutting/rapid velocity loop gain switching function.
1700 (FS15i) Velocity loop gain magnification for cutting (%)

2107 (FS30i,16i)
[Series30i, 16i, and so on]

Cutting/rapid velocity loop gain
Velocity loop gain [%]
switching function
No. 2202#1=0 (disabled) Always (1 + No. 2021 / 256) × 100
No. 2202#1=1 (enabled)
Cutting feed (1 + No. 2021 / 256) × No. 2107
[Series15i]
Cutting/rapid velocity loop gain
Velocity loop gain [%]
switching function
No. 1742#1=0 (disabled) Always (1 + No. 1875 / 256) × 100
Cutting feed (1 + No. 1875 / 256) × No. 1700
- 151 -
<2> Cutting/rapid fine acc./dec. switching function (including

feed-forward switching)
Although the optimum time constant of fine acc./dec. during
cutting is about 16 ms, the time constant in rapid traverse should
sometimes be set to 32 to 40 ms to reduce the impact applied at
the time of acc./dec. The feed-forward coefficient that minimizes
cutting profile error and the feed-forward coefficient that
minimizes the time for high-speed positioning in rapid traverse
are not always the same. In such cases, use the cutting/rapid fine
acc./dec. switching function.
NOTE
This function is not supported by the Series 30i
CNC.
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) FADCH
2202 (FS16i)
0: Disables the cutting/rapid fine acc./dec. switching function.
1: Enables the cutting/rapid fine acc./dec. switching function.
[Series16i, and so on]

Cutting/rapid fine acc./dec. FAD time
Position FF Velocity FF
switching function constant
No. 2202#0=0 (disabled) Always
No. 2109 No. 2092 No. 2069
Rapid traverse
Cutting feed No. 2143 No. 2144 No. 2145
[Series15i]
Cutting/rapid fine acc./dec. FAD time
Position FF Velocity FF
switching function constant
No. 1702 No. 1985 No. 1962
Rapid traverse
Cutting feed No. 1766 No. 1767 No. 1768
- 152 -
(b) Feed-forward, TCMD filter, 1/2 PI current control switching

[Series and editions of applicable servo software]
<1> Cutting/rapid feed-forward switching function

The position feed-forward coefficient and the velocity
feed-forward coefficient can also be changed without using fine
acc./dec. To do this, use the cutting/rapid feed-forward switching
function.
#7 #6 #5 #4 #3 #2 #1 #0
2602 (FS15i) FFCHG
2214 (FS30i,16i)
0: Disables the cutting/rapid feed-forward switching function.
1: Enables the cutting/rapid feed-forward switching function.

Cutting/rapid feed-forward switching function Position FF Velocity FF
No. 2092 No. 2069
Rapid traverse
Cutting feed No. 2144 No. 2145
[Series15i]
Cutting/rapid feed-forward switching function Position FF Velocity FF
No. 1985 No. 1962
Rapid traverse
Cutting feed No. 1767 No. 1768
<2> TCMD filter switching

When high frequency vibration occurs only in rapid traverse, use
of the TCMD filter, rather than the resonance elimination filter,
is sometimes effective. On the other hand, in cutting feed,
inserting an unnecessary TCMD filter lowers the vibration limit
of the velocity loop gain because of the delay in the filter. In
such a case, using the TCMD filter only for rapid traverse is
effective.
1895 (FS15i) TCMD filter coefficient

2067 (FS30i,16i)
- 153 -
1779 (FS15i) TCMD filter coefficient for rapid traverse

2156 (FS30i,16i)

Cutting/rapid feed-forward switching function TCMD filter
No. 2156=0 (disabled) Always No. 2067
Rapid traverse No. 2156
No. 2156≠0 (enabled)
Cutting feed No. 2067
[Series15i]
Cutting/rapid feed-forward switching function TCMD filter
No. 1779=0 (disabled) Always No. 1895
Rapid traverse No. 1779
No. 1779≠0 (enabled)
Cutting feed No. 1895
<3> Switching of the current loop 1/2 PI control function in cutting

feed and rapid traverse
When the cutting/rapid velocity loop gain switching function is
enabled, the current loop 1/2 PI control function is turned off at
the time of rapid traverse. Only when current loop 1/2 PI control
must be used also for rapid traverse while the cutting/rapid
velocity gain switching function is enabled, set the bit for always
enabling the current loop 1/2 PI control function.
#7 #6 #5 #4 #3 #2 #1 #0
1743 (FS15i) CRPI
2203 (FS30i,16i)
0: Disables the current loop 1/2 PI control function.
1: Enables the current loop 1/2 PI control function.
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) VGCCR
2202 (FS30i,16i)
0: Enables the current loop 1/2 PI control function for both cutting
and rapid traverse.
1: Enables the current loop 1/2 PI control function for cutting only.
NOTE
This function bit has double meanings. One is
above and another is the cutting/rapid velocity loop
- 154 -
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) PIAL
2202 (FS30i,16i)
1: Always enables the current loop 1/2 PI control function.

No. 2203#2=1 No. 2202#1 No. 2202#2
0 0
Always enables the current loop 1/2 PI control function.
1 1
Enables the current loop 1/2 PI control function for cutting only. 1 0
[Series15i]
No. 1743#2=1 No. 1742#1 No. 1742#2
0 0
Always enables the current loop 1/2 PI control function.
1 1
Enables the current loop 1/2 PI control function for cutting only. 1 0
NOTE
To disable the current loop 1/2 PI control function,
set bit 2 of parameter No. 1743 to 0 (Series 15i) or
bit 2 of parameter No. 2203 to 0 (Series 30i, 16i,
etc.).
- 155 -
4.4 VIBRATION SUPPRESSION IN THE STOP STATE
4.4.1 Velocity Loop High Cycle Management Function
(1) Overview
This function improves the velocity loop gain oscillation threshold.
This is done by performing velocity loop proportional calculation at
high speed, which determines the velocity loop oscillation threshold.
The use of this function enables the following:
• Improvement of the command follow-up characteristic of a
velocity loop
• Improvement of the servo rigidity


#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) PK2V25
2017 (FS30i, 16i)
PK2V25 (#7) 1: The velocity loop high cycle management function is used.
Configuration of the control system (for PI function)
VCMD + + TCMD
PK1V/S
− +
Proportional
PK2V
calculation
+
−
Calculated in each Calculated in each
velocity loop control cycle current loop control cycle
- 156 -
(4) Performance comparison with the acceleration feedback function

Velocity loop high cycle
Acceleration feedback function
management function
Acceleration feedback is performed Only a velocity loop proportional
Control method
at high speed. calculation is made at high speed.
Adjustment method Set a value of −10 to −20. Set the function bit.
This function may prove more
In general, this function is more
effective than the velocity loop high
effective than the acceleration
Effect cycle management function,
feedback function in improving the
depending on the machine system
velocity loop gain.
resonance frequency and intensity.
(5) Caution and notes on use

CAUTION
Depending on the resonance frequency and resonance
strength of the machine system, the use of this function may
result in machine resonance.
If this occurs, do not use this function.
NOTE
1 When this function is used, the observer function is disabled.
To remove high-frequency oscillations, use the torque
command filter.
2 The normalization of the machine speed feedback function is
disabled. If hunting cannot be eliminated by increasing the
velocity loop gain, use the vibration damping control function,
which provides a capability similar to the machine speed
feedback function.
3 In (torque command) tandem control, velocity loop high cycle
management function cannot be used with Series 9096. To use
velocity loop high cycle management function with Series 9096,
velocity command tandem control must be enabled before the
high cycle management function is enabled.
4 When this function is used, some functions are restricted as
follows:
Unavailable function Function with restricted usage
Variable proportional gain function in the Machine speed feedback;
stop state (*) normalization not performed
Non-linear control Observer used for unexpected
disturbance torque detection
Acceleration feedback
N pulses suppression function
* With Series 9096, this function cannot be used together with
the variable proportional gain function in the stop state.
With other series, this function can be used together. (See
Subsec. 4.4.3.)
- 157 -
4.4.2 Acceleration Feedback Function
(1) Overview
The acceleration feedback function is used to control velocity loop
oscillation by using motor speed feedback signal multiplied by the
acceleration feedback gain to compensate the torque command.
This function can stabilize unstable servo :
• When motor and machine have a spring coupling.
• When the external inertia is great compared to the motor inertia.
This is effective when vibration is about 50 to 150 Hz.
Fig 4.4.2 is a velocity loop block diagram that includes acceleration
feedback function.
Load inertia
1/(J1 • s)
Torque
Spring
command filter
coupling
VCMD + + +
PK1V/s A/(s + A) Kt 1/(Jm • s)
− − −
Torque Motor inertia
constant
PK2V Ka • s
Speed feedback
PK1V : velocity loop integral gain
PK2V : velocity loop proportional gain
Ka : acceleration feedback gain
Fig. 4.4.2 Velocity loop block diagram that includes acceleration feedback function


Specifying the following parameters as a negative value enables the
acceleration feedback function.
1894 (FS15i) Acceleration feedback gain

2066 (FS30i, 16i)
[Valid data range] -10 to -20
- 158 -
(4) Caution and note

CAUTION
If the acceleration feedback gain is too large,
abnormal sound or vibration can occur during
acc./dec.
To solve this problem, reduce the gain.
NOTE
This function is disabled when the velocity loop
high cycle management function (see Subsec.
4.4.1) is used.
- 159 -
4.4.3 Variable Proportional Gain Function in the Stop State
(1) Overview
The velocity gain or load inertia ratio is generally increased if a large
load inertia is applied to a motor, or to improve the response. An
excessively large velocity gain may cause the motor to generate a
high-frequency vibration when it stops. This vibration is caused by
excessive proportional gain of the velocity loop (PK2V) when the
motor is released within the backlash of the machine in the stop state.
This function decreases the velocity loop proportional gain (PK2V) in
the stop state only. The function can suppress the vibration in the stop
state and also enables the setting of a high velocity gain.

Series 90D0/A(01) and subsequent edition
Series 90E0/A(01) and subsequent edition
Series 9096/A(01) and subsequent edition
Series 90B0/A(01) and subsequent edition

#7 #6 #5 #4 #3 #2 #1 #0
1958 (FS15i) PK2VDN
2016 (FS30i, 16i)
PK2VDN (#3) 1: The variable proportional gain function in the stop state is used.
1730 (FS15i) Variable proportional gain function in the stop state : Stop judgment level
2119 (FS30i, 16i)
[Unit of data] Detection unit
[Recommended value] 2 to 10 (Detection unit: 1 µm)
20 to 100 (Detection unit: 0.1 µm)
With Series 90B0, 90B6, or 90B5, a function for decreasing a set

proportional gain in the stop state to 50% as well as 75%, and a
function for setting an arbitrary magnification only in cutting feed are
available. When decreasing the velocity loop proportional gain in the
stop state to 50%, set the following bit parameter in addition to the
function bit for the function for changing the proportional gain in the
stop state and the parameter for stop determination level.
- 160 -
#7 #6 #5 #4 #3 #2 #1 #0
1747 (FS15i) PK2D50
2207 (FS30i, 16i)
PK2D50 (#3) When the variable proportional gain function in the stop state enabled
(K2VDN = 1):
0: The velocity loop proportional gain in the stop state is 75%.
1: The velocity loop proportional gain in the stop state is 50%.
When an arbitrary magnification is used for a proportional gain in the

stop state during cutting feed, set the function bit for stop judgment
level of the function for changing the proportional gain in the stop
state. In addition, set the following parameter:
2737 (FS15i) Variable proportional gain function in the stop state : Arbitrary magnification
in the stop state (during cutting feed only)
2324 (FS30i, 16i)
[Unit of data] %
[Recommended value] 25 to 100
(4) Example of parameter setting

(a) When the cutting feed/rapid traverse switchable velocity loop
gain function (Sec. 4.3) is not used, and
Bit 3 of No. 1958 (Series 15i) or bit 3 of No. 2016 (Series 30i,
16i, and so on) = 1
Actual velocity gain in the stop state=(velocity gain setting)×0.75
(b) When the cutting feed/rapid traverse switchable velocity loop
gain function (Sec. 4.3) is not used,
16i, and so on) = 1, and
16i, and so on) = 1
Actual velocity gain in the stop state=(velocity gain setting)×0.5
(c) When the cutting feed/rapid traverse switchable velocity loop
gain function (Sec. 4.3) is not used,
No. 2373 (Series 15i) or No. 2324 (Series 30i,16i, and so on) = α
Actual velocity gain in the stop state=(velocity gain setting)×α/100
When the absolute value of an error is lower than the stop judgment
level, the function changes the proportional gain of the velocity loop
(PK2V) to 75% or 50% of the set value.
If the machine vibrates while in the stop state, enable this function and
set a value greater than the absolute value of the error causing the
vibration as the stop judgment level. The function cannot stop the
vibration of a machine in the stop state when the current velocity loop
proportional gain is too high. If this occurs, reduce the velocity loop
proportional gain.
- 161 -
Error
Velocity loop proportional gain ( PK2V) 100%
Error = + (stop judgement level)

Velocity loop
Error = 0
proportional gain (PK2V) 75% or 50%
Error = − (stop judgement level)
Velocity loop proportional gain ( PK2V) 100%
Fig. 4.4.3 Relationship between error and velocity loop proportional gain
(PK2V)
NOTE
This function is disabled when the velocity loop
high cycle management function (Subsec. 4.4.1) is
used with Series 9096.
[Tip] Example of setting an arbitrary magnification in the stop state

(a) When the cutting feed/rapid traverse switchable velocity loop
gain function (Sec. 4.3) is used, and
16i, and so on) = 1
• If the mode in the stop state is the cutting mode:
Actual velocity gain in the stop state = (velocity gain setting
for cutting) × 0.75
• If the mode in the stop state is the rapid traverse mode:
for rapid traverse) × 0.75
(b) When the cutting feed/rapid traverse switchable velocity loop
gain function (Sec. 4.3) is used,
16i, and so on) = 1
for cutting) × 0.5
(c) When the cutting feed/rapid traverse switchable velocity loop
for cutting) × α/100
- 162 -
(d) When the cutting feed/rapid traverse switchable velocity loop

16i, and so on) = 1,
for cutting) × α/100
- 163 -
4.4.4 N Pulses Suppression Function
(1) Overview
Even a very small movement of the motor in the stop state may be
amplified by a proportional element of the velocity loop, thus
resulting in vibration. The N pulse suppression function suppresses
this vibration in the stop state.
When vibration occurs as shown in Fig. 4.4.4 (a), the velocity
feedback at point B generates an upward torque command to cause a
return to point A. A downward torque command, generated by the
velocity feedback at point A is greater than the friction of the machine,
causing another return to point B. This cycle repeats itself, thus
causing the vibration.
Motor position
Stop position 1 pulse

Point A grid
Point B
Torque by
proportional
element
Time
Fig.4.4.4 (a) N pulse suppression function disabled (Torque due to the
proportional term keeps up, leading to vibration.)
To suppress such vibration, it is necessary to exclude from the

velocity loop proportional term the speed feedback pulses generated
when the motor returns from point B to point A.
If the N pulse suppression function is enabled as shown in Fig. 4.4.4
(b), the feedback pulses generated when the motor returns from point
B to point A are excluded from the velocity loop proportional term.
The standard setting of the grid width at point A is 1 µm. It can be
changed by specifying the level parameter.
- 164 -
Motor position
The function works at this point.
N pulse suppression
Stop position level parameter
Point A (setting standard value
is 1 pulse)
Point B
Torque by
proportional
element
Time
Fig. 4.4.4 (b) N pulse suppression function disabled
(The N pulse suppression function restricts the torques due to the proportional term,
thus eliminating vibration.)


#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) NPSP
2003 (FS30i, 16i)
NPSP (#4) 1: To enable the N pulse suppression function
1992 (FS15i) N-pulse suppression level parameter (ONEPSL)

2099 (FS30i, 16i)
[Standard setting] 400
400 means a single pulse as a detection unit.
- 165 -
4.4.5 Current Loop 1/2 PI Control Function
(1) Overview
To improve servo performance in high-speed and high-precision
machining, high-speed positioning, ultrahigh-precision positioning,
and so forth, a velocity loop gain as high as possible needs to be set
stably.
To set a high velocity loop gain stably, the response of the current
loop needs to be improved.
The current loop 1/2 PI control function enables the response of the
current loop to be improved.

(3) Control method

As shown in Fig. 4.4.5, in the area where a small current flows, a
current loop calculation is based on PI control rather than on the
conventional IP control method. When a large current flows, the
control method returns to IP control to suppress a current overshoot.
Torque command PWM command
PK1/s -
PK2
Switching to the p
intermediate state of PI −
control and I-P control
+
The proportional from the command is added to PWM calculation.
Fig. 4.4.5 Block diagram of current loop 1/2PI control

<1> Enabling the current loop 1/2 PI control function at all times
#7 #6 #5 #4 #3 #2 #1 #0
1743 (FS15i) CRPI
2203 (FS30i, 16i)
CRPI (#2) 1: To enable the current loop 1/2 PI control function
- 166 -
<2> To enable the function for cutting only, use the following bit in
addition to the previous bit:
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) VGCCR
2202 (FS30i, 16i)
VGCCR (#1) 1: To enable the current loop 1/2 PI control function for cutting only
(This function is used together with the cutting feed/rapid traverse
velocity loop gain switch function.)
<3> To enable the function at all times while using bit 1 of parameter
No. 1742 (Series 15i) or No. 2202 (Series 16i and so on), use the
following bit in addition to the settings of <1> and <2>:
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) PIAL
2202 (FS30i, 16i)
PIAL (#2) 1: To enable the current loop 1/2 PI control function at all times
(When this function is used together with the cutting feed/rapid
traverse velocity loop gain switch function)
CAUTION
If the motor activation sound or vibration in the stop
state increases when this parameter is set, turn off
this parameter (do not use this parameter).
(5) Current control PI rate modification

The current control PI rate (p in Fig. 4.5.5) is usually fixed at 1/2, but
can be changed freely.
* This function cannot be used with Series 9096.
2736 (FS15i) Current control PI rate
2323 (FS30i, 16i)
[Unit of data] 4096 represents p = 1.0 (complete PI).
When the value 0 is specified, the specification of 2048 (1/2PI), which
is equivalent to p = 0.5, is assumed.
CAUTION
If you need to increase the velocity gain, in
particular, a value greater than 1/2PI may be set.
However, do not use this parameter usually.
- 167 -
4.5 MACHINE RESONANCE ELIMINATION FUNCTION
4.5.1 Selecting a Resonance Elimination Function

The frequency band where the resonance elimination functions
produce elimination effects varies from one function to another.
Check the resonance frequency in question with SERVO GUIDE or a
vibrometer then select a resonance elimination function according to
the frequency.
The figure below shows the classified functions and their effective
resonance frequency bands.
Low frequency Middle frequency High frequency
Classification 0Hz 100H 200Hz 400Hz 800Hz
Disturbance elimination filter Torque command filter
Elimination of resonance
50Hz 100H 120H 180H 400H
component from command Resonance elimination filter L Resonance elimination filter
50Hz 200Hz
Elimination of resonance Observer
component from Fb 150Hz 400Hz
Dual position Fb
Stabilization of full-closed 50Hz
system Machine velocity Fb, vibration damping control
50Hz
Stabilization using Machining point control
acceleration sensor
50Hz
* The figure above shows guideline frequencies.

* For vibration at 120 Hz to 180 Hz, a disturbance elimination filter or torque command filter may be useful. A vibration
improvement may be made by applying the current loop 1/2PI function or by fine velocity loop gain tuning.
* The observer function may have an adverse effect such as instability produced at stop time. For resonance
elimination at middle to high frequencies, try a torque command filter or resonance filter first. Only when resonance
still exists, use the observer function.
* The resonance elimination functions for use at low frequencies have the following features:
Function Feature
Resonance elimination Parameter setting is easy, and a large resonance elimination effect can be expected.
filter L However, precision degradation (such as overshoot) is unavoidable. So, this function is
not suitable for applications that require high precision. By using an exclusion rate, the
precision and elimination effect need to be balanced.
Disturbance elimination This function compensates for a torque command, so that precision is less affected.
filter However, the maximum torque may decrease.
Dual position Fb, These functions are dedicated to a full-closed system and improve vibration (instability)
machine velocity Fb, caused by a twist between the motor and scale. The order of effect is: Dual position Fb >
vibration damping control Machine velocity Fb = Vibration damping control.
Machining point control This function has a limited influence on precision and produces a high elimination effect.
Depending on the setting of gain, an acceleration loop may oscillate. An acceleration
sensor needs to be installed.
- 168 -
4.5.2 Torque Command Filter (Middle-Frequency Resonance

Elimination Filter)
(1) Overview
The torque command filter applies a primary low-pass filter to the
torque command.
If the machine resonates at one hundred Hz or over, this function
eliminates resonance at such high frequencies.

(3) Explanation
Fig. 4.5.2 shows the configuration of a velocity loop including the
torque command filter.
VCMD + TCMD
PK1V/s + Kt/Jm ⋅ s
-
Motor
Torque command filter
Velocity feedback
Fig. 4.5.2 Configuration of velocity loop including torque command filter
As shown in Fig. 4.5.2, the torque command filter applies a low–pass

filter to the torque command. When a mechanical system contains a
high resonant frequency of more than 100Hz, the resonant frequency
component is also contained in the velocity feedback shown in Fig.
4.5.2 and may be amplified by proportional term. However, the
resonance is prevented by interrupting the high–frequency component
of the torque command using the filter.
(4) Proper use of the observer and torque command filter

The torque command filter is set in the forward direction. Therefore,
there are fewer bad influences exerted upon the entire velocity control
system than the observer that filters a feedback signal. If the resonance
is very strong and it cannot be eliminated, use the observer.
Use the torque command filter first when the mechanical system
resonates at high frequency. If the resonance cannot be eliminated, use
the observer.
- 169 -

1895 (FS15i) Torque command filter (FILTER)
2067 (FS30i, 16i)
[Typical setting] 1166 (200 Hz) to 2327 (90 Hz)
When changing the torque command filter setting, see Table 4.5.2.
As the cut-off frequency, select the parameter value corresponding to
a half of the vibration frequency from the table below.
(Example)
In the case of 200-Hz vibration, select a cutoff frequency of 100
Hz for the torque command filter, and set FILTER = 2185.
CAUTION
Do not specify 2400 or a greater value. Such a high
value may increase the vibration.
Table 4.5.2 Parameter setting value of torque command filter

Cutoff Setting value of Cutoff Setting value of
frequency (Hz) parameter frequency (Hz) parameter
60 2810 140 1700
65 2723 150 1596
70 2638 160 1499
75 2557 170 1408
80 2478 180 1322
85 2401 190 1241
90 2327 200 1166
95 2255 220 1028
100 2185 240 907
110 2052 260 800
120 1927 280 705
130 1810 300 622
(6) Cutting feed/rapid traverse switchable torque command filter

With this function, the torque command filter coefficient can be
switched between rapid traverse and cutting feed to improve
contouring accuracy during cutting and increase a maximum feedrate
and maximum acceleration during rapid traverse at the same time.
1779 (FS15i) Torque command filter coefficient for rapid traverse

2156 (FS30i, 16i)
[Valid data range] 1166 (200 Hz) to 2327 (90 Hz)
When 0 is set, the cutting feed/rapid traverse switchable torque
command filter is disabled. The normal filter coefficient (No. 1895 for
Series 15i or No. 2067 for Series 30i, 16i, and so on) is used at all
times.
When a value other than 0 is set, No. 1779 (Series 15i) or No. 2156
(Series 30i, 16i, and so on) is used for stop time, rapid traverse, and
jog feed, and No. 1895 (Series 15i) or No. 2067 (Series 30i, 16i, and
so on) is used for cutting only.
- 170 -
4.5.3 Resonance Elimination Filter Function (High-Frequency

Resonance Elimination Filter)
(1) Overview
A filter function for removing high-speed resonance is added. With
this function, high-speed resonance can be removed to set a higher
velocity loop gain.

Series 90B0/P(16) and subsequent editions (*)
(*) With Series 90B0, resonance elimination filters that can be used
are restricted depending on the edition.
Edition of
Restriction
Series 90B0
A(01) to I(09) Only resonance elimination filter 1 (conventional
specification) can be used. Resonance elimination filters 2
to 4 and damping setting, cannot be used.
J(10) to O(15) Resonance elimination filters 1 to 4 (extended
specification) and damping setting can be used.
P(16) or later All resonance elimination filter functions can be used.
(3) Control block diagram

RE filter 1 RE filter 2 RE filter 3 RE filter 4
Torque
command To motor
This filter can be used as For this filter, it is For this filter, it is This filter can
a resonance elimination possible to specify possible to specify handle up to four
filter designed to the an attenuation a bandwidth resonance
conventional specification. ratio. freely. frequencies.
It can follow the (RE filters 1 to 4) (RE filters 1 to 4)
resonance frequency.
(RE filter 1 only)
Fig. 4.5.3
- 171 -

CAUTION
1 If the frequency of a resonance elimination filter is
set to a low frequency around 100 Hz, the control
system can become unstable, resulting in a large
vibration.
2 Modify parameters in the emergency stop state.

<1> Setting for resonance elimination filters 2 to 4
The resonance elimination filter has a function for cutting signals of a
particular frequency band. Three parameters are used for this filter.
They specify the center frequency of a range to be cut, a bandwidth to
be cut, and damping separately.
2773 (FS15i) RE filter 2 : Attenuation center frequency
2360 (FS30i, 16i)
[Valid data range] 96 to 1000(HRV1 or HRV2), 96 to 2000(HRV3), 96 to 4000(HRV4)
(independent of the damping setting)
[Unit of data] Hz
2774 (FS15i) RE filter 2 : Attenuation bandwidth

2361 (FS30i, 16i)
[Valid data range] 0 to attenuation center frequency (independent of the damping setting)
[Unit of data] Hz
2775 (FS15i) RE filter 2 : Damping

2362 (FS30i, 16i)
[Valid data range] 0 to 100 (If it is 0, the attenuation ratio is maximized.)
[Unit of data] %
Resonance elimination filters 3 and 4 have the same specification as

resonance elimination filter 2.
2363 (FS30i, 16i)

2364 (FS30i, 16i)

2365 (FS30i, 16i)

2366 (FS30i, 16i)

2367 (FS30i, 16i)

2368 (FS30i, 16i)
- 172 -
CAUTION
1 For resonance elimination filters 2 to 4, there is no
specification that supports compatibility with
conventional resonance elimination filters. Even if
damping = 0, an arbitrary attenuation bandwidth
can be specified for them.
2 Resonance elimination filters 2 to 4 are enabled if a
nonzero value is set in the attenuation bandwidth
or damping parameters for them. If you do not want
use these resonance elimination filters, reset all the
three parameters (attenuation center frequency,
attenuation bandwidth, and damping) to 0.
3 The parameter for resonance elimination filter 4 is
used to set a coefficient for resonance elimination
filter L when resonance elimination filter L is
enabled (bit 1 of No. 2221=1 (Series 30i, 16i,
etc.)/bit 1 of No. 2609=1 (Series 15i)).
<2> Setting for resonance elimination filter 1

Only resonance elimination filter 1 has the conventional specification
if the damping is 0 and the improved specification if the damping is
not 0.

2113 (FS30i, 16i)
[Valid data range] 250 to 992 (if damping = 0)
96 to 1000(HRV1 or HRV2), 96 to 2000(HRV3), 96 to 4000(HRV4)
(if damping ≠ 0)
[Unit of data] Hz

2177 (FS30i, 16i)
[Valid data range] 20, 30, 40 (if damping = 0)
0 to attenuation center frequency (if damping ≠ 0)
[Unit of data] Hz

2359 (FS30i, 16i)
[Valid data range] 0 (If it is 0, the resonance elimination filer has the conventional
specification.)
1 to 100 (If it is 1, the attenuation ratio is maximized. For resonance
elimination filer 1.)
[Unit of data] %
- 173 -
CAUTION
1 If damping = 0 for resonance elimination filter 1,
this filter has the same specification as for
conventional resonance elimination filters. So, its
attenuation bandwidth can be set only to 20, 30, or
40 Hz (specification compatible with conventional
resonance elimination filters).
2 Resonance elimination filter 1 is enabled if a
nonzero value is set in the attenuation bandwidth
or damping parameter for it. If you do not want use
the resonance elimination filter, reset all the three
parameters (attenuation center frequency,
attenuation bandwidth, and damping) to 0.
[Parameters for resonance elimination filters]

For Series 30i or 16i
Attenuation center Attenuation
Damping
frequency [Hz] bandwidth
For Series 15i

Attenuation center Attenuation
Damping
frequency [Hz] bandwidth
- 174 -
(6) Example of filter characteristics

<1> Conventional resonance elimination filter
Gain
0
-5
-10
-15
Center frequency = 300 Hz
-20
10
1
10
2
10
3
10
4 Bandwidth = 30 Hz
Phase
Damping = 0
100
50
-50
-100
1 2 3 4
10 10 10 10
<2> Improved resonance elimination filter (with damping)

Gain
0
-5
-10
-15
Bandwidth = 100 Hz
-20
10
1
10
2 3
10
4
10 Damping = 50%
Phase
100
50
-50
-100
1 2 3 4
10 10 10 10
<3> Improved resonance elimination filter (with two stages of damping)

Gain
0
-5
(First stage)
-10 Center frequency = 300 Hz
-15 Bandwidth = 50 Hz
-20
Damping = 30%
1 2 3 4
10 10 10 10
(Second stage)
100
Phase
50
Bandwidth = 100 Hz
Damping = 50%
0
-50
-100
1 2 3 4
10 10 10 10
- 175 -
4.5.4 Disturbance Elimination Filter Function (Low-Frequency

Resonance Elimination Filter)
(1) Overview
The disturbance elimination filter function estimates a disturbance by
comparing a specified torque with the actual velocity, and feeds
forward the estimation to the specified torque to suppress the effect of
the disturbance. In particular, this function is useful for a vibration of
50 Hz to 100 Hz.
Disturbance elimination filter Disturbance
+ Motor
Specified + Velocity fb
torque Gain 1/Jm⋅s
Tcmd +
+
Estimated s
disturbance
Gain
Kd Filter Limiter
La
+ Inverse function
gain Filter
- Jmo
Fig. 4.5.4(a) Configuration of disturbance elimination filter

#7 #6 #5 #4 #3 #2 #1 #0
2611 (FS15i) DISOBS
2223 (FS30i, 16i)
DISOBS (#0) The disturbance elimination filter function is:
0 : Disabled.
1 : Enabled.
2731 (FS15i) Disturbance elimination filter gain (Kd)
2318 (FS30i, 16i)
[Typical setting] 500
NOTE
If a gain of 0 to 100 is set, the disturbance
elimination filter function does not operate.
- 176 -
2732 (FS15i) Inertia ratio (Rj) (%)

2319 (FS30i, 16i)
Set an inertia ratio (= machine inertia/motor inertia) in %.
Usually, set 100%.
2733 (FS15i) Inverse function gain (Jmo)

2320 (FS30i, 16i)
[Initial setting] 100 (Increase the setting step by step.)
Set an inverse function gain as a conversion coefficient for
acceleration-to-TCMD conversion. This parameter needs to be
adjusted. As a guideline, set a value not greater than the value
obtained by the following expressions:
Linear motor (The detection unit of the scale is assumed to be p µm.)
Jmo = 466048×p×Jm/Kt/Imax
Rotary motor
Jmo = 1396264×Jm/Kt/Imax
Jm: Weight [kg] or inertia [kgm2]
Kt: Torque constant [N/Ap] or [Nm/Ap]
Imax: Maximum amplifier current [Ap]
NOTE
If an excessively large gain value is set, an
abnormal sound and vibration can occur.
2734 (FS15i) Filter time constant (Tp)

2321 (FS30i, 16i)
• When HRV1, HRV2, or HRV3 is used:

[Typical setting] 3700 (equivalent to T = 10 ms).
* Usually, this value does not need to be changed.
Set a filter time constant for determining an estimated disturbance
velocity by using the following expression:
Tp = 4096 × exp (-t/T)
T: Setting time constant [sec], t = 0.001 [sec]
• When HRV4 is used:
[Typical setting] 3994 (equivalent to T = 10 ms).
* Usually, this value does not need to be changed.
Set a filter time constant for determining an estimated disturbance
velocity by using the following expression:
Tp = 4096 × exp (-t/T)
T: Setting time constant [sec], t = 0.00025 [sec]
- 177 -
2735 (FS15i) Acceleration feedback limit (La)

2322 (FS30i, 16i)
Set a limiter for a feedback torque calculated from acceleration. This
parameter suppresses an excessive motion at the time of adjustment.
The value 7282 represents a maximum amplifier current. When a
160-A amplifier is used, for example, the value 1000 is equivalent to
22 A.
NOTE
In a case where a value close to the torque limit
may be used, the torque is limited if the
acceleration feedback limit is not increased.
(4) Procedure
(1) Make an adjustment according to the procedure below. First,
disable those functions that operate only in the stop state such as
the function for changing the proportional gain in the stop state.
For determining the resonance frequency and adjusting the
disturbance elimination filter, use frequency characteristics
measurement by SERVO GUIDE.
(2) Enable the disturbance elimination filter function, set the

disturbance elimination filter gain to 100 (not functioning), then
measure the frequency characteristics.
With SERVO GUIDE, observe the response waveform obtained
during the above measurement, and set the input amplitude (to
about 500) to allow the waveform to be observed and machine
sound to be heard. A sinusoidal torque command is used, so that
the command does not generate a torque in one direction. The
command is to be executed away from the machine stroke limits.
Swell in gain
Fig. 4.5.4(b) Measurement example using SERVO GUIDE (before

adjustment)
- 178 -
(3) Set the disturbance elimination filter gain to 500, and check the
frequency characteristics with SERVO GUIDE while increasing
the gain for inverse model starting with 100 in steps of 100.
Adjust the value so that the amplitude of the gain swell part
becomes small.
Improved
Fig. 4.5.4(c) Measurement example using SERVO GUIDE (after

adjustment)
(4) Note that the velocity loop gain of higher frequencies is

increased and even a violent vibration may be caused simply by
enabling the disturbance elimination filter function. If a vibration
occurs, increase the inverse function gain gradually, and check
the vibration of the torque command. If the vibration becomes
greater, decrease the inverse function gain. If the vibration can
not be reduced by increasing and decreasing the inverse function
gain, change the filter time constant by ±50 to eliminate the
vibration.
(5) If the frequency of vibration is higher than 100 Hz, use a separate
machine resonance prevention function such as the vibration
suppression filter and torque command filter.
- 179 -
4.5.5 Resonance Elimination Filter L (Low-Frequency Resonance

Elimination Filter)
(1) Overview
The resonance elimination filter L function eliminates low-frequency
vibration by applying a filter designed to eliminate low-frequency
components to a feed-forward command/velocity command.
This function reduces low-frequency vibration but can degrade
contouring accuracy in high-speed feed. Before using this function,
check the accuracy.
Exclusion
Feed-forward
rate
1 - Exclusion
rate
Position Position =1 Resonance Velocity loop

command － gain elimination filter L
VFFNCH(#2)
=0
Position feedback


For resonance elimination filter L, the fourth-stage parameter of an
ordinary resonance elimination filter for the torque command is used.
So, the two filters cannot be used at the same time.
To use the resonance elimination filter L function, enable the function
bit (LNOTCH) below.
#7 #6 #5 #4 #3 #2 #1 #0
2609(FS15i) VFFNCH LNOTCH
2221(FS30i,16i)
LNOTCH(#1)
0: Uses resonance elimination filter 4.
1: Uses resonance elimination filter L.
VFFNCH(#2) Resonance elimination filter L is applied to:
0: Feed-forward part only of the velocity command (← Default)
1: Entire velocity command
- 180 -
NOTE
1 To enhance the elimination effect, set VFFNCH to
1.
Set the following filter parameters:

2779(FS15i) Resonance elimination filter L/resonance elimination filter 4 attenuation
center frequency
2366(FS30i,16i)
[Unit of data] Hz
2780(FS15i) Resonance elimination filter L/resonance elimination filter 4 attenuation

bandwidth
2367(FS30i,16i)
[Unit of data] Hz
2781(FS15i) Resonance elimination filter L/resonance elimination filter 4 damping

2368(FS30i,16i)
[Valid data range] 10 to 100 (A maximum attenuation rate is specified when 0 is set.)
[Unit of data] %
CAUTION
To stop the use of this function, be sure to set all
parameters above to 0 then restart the CNC.
NOTE
When the value 4 or a smaller number is specified
as the attenuation center frequency, an illegal
parameter setting alarm (detail number 3663 or
3603) is issued. Set the value 5 or a greater
number.
- 181 -
2769(FS15i) Resonance elimination filter L/feed-forward filter exclusion rate

2356(FS30i,16i)
[Unit of data] %
When resonance elimination filter L is applied to the feed-forward
part, contouring accuracy can degrade. So, this function is used to
balance contouring accuracy and the effect of resonance elimination.
When 100% is set, this filter is not applied to the feed-forward part.
When 50% is set, this filter is applied to a half of the feed-forward
part.
Exclusion rate 100% Exclusion rate 50% Exclusion rate 0%
Contouring accuracy High Contouring accuracy Low

Elimination effect Low Observe contouring accuracy Elimination effect High
and elimination effect
for optimum value adjustment.
Example of effect
Resonance elimination filter L: Disabled Resonance elimination filter L: Enabled
Motor velocity Motor velocity
Motor acceleration Motor acceleration
- 182 -
4.5.6 Observer Function
(1) Overview
The observer is used to eliminate the high-frequency component and
to stabilize a velocity loop when a mechanical system resonates at
high frequency of several hundred Hertz.
The observer is a status observer that estimates the controlled status
variables using the software.
In a digital servo system, the speed and disturbance torque in the
control system are defined as status variables. They are also estimated
in the observer. An estimated speed consisting of two estimated values
is used as feedback. The observer interrupts the high-frequency
component of the actual speed when it estimates the speed.
High-frequency vibration can thus be eliminated.
(2) Explanation
Fig. 4.5.6 (a) shows a block diagram of the velocity loop including an
observer.
Velocity feedback
VCMD +
PK1V/s + PK2V Kt/(Jm • s)
−
TCMD
Observer
Estimated speed
Fig. 4.5.6 (a) Configuration of velocity loop including observer
Fig. 4.5.6 (b) shows a block diagram of the observer.

Disturbance Motor
TCMD Velocity feedback
+
Kt 1/(Jm • s)
+
+
−
POK2/s POK1
+ +
POA1
+
1/s
Estimated
Motor model speed
Fig. 4.5.6 (b) Block diagram of the observer
POA1, POK1, and POK2 in Fig. 4.5.6 (b) correspond to digital servo
parameters. The observer has an integrator as a motor model. POA1 is
a coefficient that converts the torque command into motor acceleration
and is the characteristic value of the motor. The motor model is
accelerated by this value. The actual motor is also accelerated by the
torque and disturbance torque that it generates.
- 183 -
The disturbance torque works on the actual motor. There is a time lag
in the current loop. The POA1 value does not completely coincide
with the actual motor. This is why the motor’s actual velocity differs
from the motor speed estimated by an observer. The observer is
compensated by this difference. The motor model is compensated
proportionally (POK1), and the observer is compensated integrally
(POK2/s).
POK1 and POK2 act as a secondary low–pass filter between the actual
speed and estimated speed. The cutoff frequency and damping are
determined by the POK1 and POK2 values. The difference between
the observer and low-pass filter lies in the existence of a POA1 term.
Using POA1, the observer’s motor model can output an estimated
speed that has a smaller phase delay than the low–pass filter.
When an observer function is validated, the estimated speed in Fig.
4.5.6 (b) is used as velocity feedback to the velocity control loop. A
high–frequency component (100 Hz or more) contained in the actual
motor speed due to the disturbance torque’s influence may be further
amplified by the velocity loop, and make the entire system vibrate at
high frequency. The high frequency contained in the motor’s actual
speed is eliminated by using the velocity feedback that the observer
outputs. High–frequency vibration can be suppressed by feeding back
a low frequency with the phase delay suppressed.
In some systems, the use of the observer function can suppress
vibration during movement but makes the machine unstable while it is
in the stop state. In such cases, use the function for disabling the
observer in the stop state, as explained in Art. (7) of this section.

Series 90B5/8(01) and subsequent editions

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) OBEN
2003 (FS30i, 16i)
OBEN (#2) 1: To enable the observer function
1859 (FS15i) Observer coefficient (POA1)

2047 (FS30i, 16i)
[Setting value] Keep the standard setting unchanged.
- 184 -
1862 (FS15i) Observer coefficient (POK1)

2050 (FS30i, 16i)
[Setting value] Usually, use the standard setting.
[Setting value] 956 → To be changed to 264
1863 (FS15i) Observer coefficient (POK2)

2051 (FS30i, 16i)
[Setting value] Usually, use the standard setting.
(5) Note
The parameter is initially set to such a value (standard setting) that the
cutoff frequency of the filter becomes 30 Hz. With this setting, the
effect of filtering becomes remarkable at resonance frequencies above
the range of 150 Hz to 180 Hz.
To change the cutoff frequency, set parameters POK1 and POK2 to a
value listed below, while paying attention to Table 4.5.6:
Generally, the observer function does not work unless its cutoff
frequency is held below Fd/5 or Fd/6, where Fd is the frequency
component of an external disturbance. However, if this bandwidth is
some 20 Hz or lower, the velocity loop gain also drops or becomes
unstable, possibly causing a fluctuation or wavelike variation.
Table 4.5.6 Changing the observer cutoff frequency

HRV1, HRV2, HRV3 HRV4
Cutoff frequency (Hz)
POK1 POK2 POK1 POK2
10 348 62 90 4
20 666 237 178 16
30 956 510 264 35
40 1220 867 348 62
50 1460 1297 430 96
60 1677 1788 511 136
70 1874 2332 1874 183
(6) Setting observer parameters when the unexpected disturbance torque

detection function is used
The unexpected disturbance torque detection function (see Sec. 4.12)
uses the observer circuit shown in Fig. 4.5.6 (b) to calculate an
estimated disturbance. In this case, to improve the speed of calculation,
change the settings of observer parameters POA1, POK1, and POK2
by following the explanation given in Sec. 4.12.
When the observer function and unexpected disturbance torque
detection function are used together, however, the defaults for POK1
and POK2 must be used.
- 185 -
(7) Stop time observer disable function

If the observer function is enabled, the machine may fluctuate and
become unstable when it stops. Such a fluctuation or unstable
operation can be prevented by disabling the observer function only in
the stop state.

<1> Function bit
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) MOVOBS
2018 (FS30i, 16i)
MOVOBS (#1) The function for disabling the observer in the stop state is:
0: Disabled
1: Enabled ← Set this value.
<2> Level at which the observer is determined as being disabled

1730 (FS15i) Level at which the observer is determined as being disabled
2119 (FS30i, 16i)
[Typical setting] 1 to 10
If the absolute value of the position error is less than the level at which
the observer is determined as being disabled, the observer function is
disabled.
NOTE
This parameter is also used for the stop
determination level of the function for changing the
proportional gain in the stop state.
(Usage)
Set the function bit and the level at which the observer is determined
as being disabled so that it is greater than the peak absolute value of
the oscillating position error.
- 186 -
4.5.7 Vibration Damping Control Function
(1) Overview
In a closed-loop system, the Pulsecoder on the motor is used for
velocity control and a separate detector is used for position control.
During acc./dec., the connection between the motor and machine may
be distorted, causing the speed transferred to the machine to slightly
differ from the actual motor speed. In such a case, it is difficult to
properly control the machine (reduce vibration on the machine).
The vibration damping control function feeds back the difference
between the speeds on the motor and machine (speed transfer error) to
the torque command, to reduce vibration on the machine.
This function has the effect of the machine velocity feedback function,
but is superior to the machine velocity feedback function in that
restrictions as imposed with the machine velocity feedback function
are eliminated.
(2) Control method

The following figure shows the block diagram for vibration damping
control:
Position command
+ Velocity + Torque command
Kp Motor Machine
compensator
+ − − −
+ Conversion
Filter coefficient
−
Vibration-
damping
control gain Speed transfer error
Velocity feedback
Position feedback
Fig. 4.5.7 Block diagram for vibration damping control

- 187 -

1718 (FS15i) Number of position feedback pulses for vibration damping control
conversion coefficient
2033 (FS30i, 16i)
[Valid data range] -32767 to 32767
When 0 is set, this function is disabled.
If a negative value is specified, it is internally read as 10 times the
specified value. (-1000=10000)
When a flexible feed gear (F⋅FG) is used
(In the case of using the A/B phase separate type detector and analog SDU)
Set value = Number of feedback pulses per motor revolution, received from a
separate detector/8
(Example 1)
With a 5 mm/rev ball screw, 0.5 µm/pulse separate detector, and
a detection unit of 1 µm, F⋅FG = 1/2
Then,
Set value = 10,000 × 1/8 = 1250
(In the case of using the serial separate type detector)
Set value = Number of feedback pulses per motor revolution, received from a
separate detector (after feedback pulse)/8
(Example 2)
If a flexible feed gear is used under the conditions described in
example 1 above,
Set value = 10,000 × 1/2 × 1/8 = 625
(In the case of using the analog SDU)
Set value = (Travel distance per motor revolution [mm]) / (detector signal
pitch [mm]) × 512 / 8
(Example 3)
When travel distance per motor revolution=10 [mm], and
detector signal pitch=20 [µm]
Set value = 10 / 0.020 × 512 / 8 = 32000
CAUTION
If the above expression is indivisible, set the
nearest integer.
1719 (FS15i) Vibration-damping control gain

2034 (FS30i, 16i)
[Valid data range] −32767 to 32767
[Standard setting] About 500
This is the feedback gain for vibration damping control.
Adjust the value in increments of about 100, observing the actual
vibration. An excessively large gain will amplify the vibration.
If setting a positive value amplifies the vibration, try setting a negative
value.
- 188 -
4.5.8 Dual Position Feedback Function Optional function
(1) Overview
A machine with large backlash may cause vibrations in a closed loop
system even if it works steadily in a semi–closed loop system. The
dual position feedback function controls the machine so that it
operates as steadily as in the semi–close system.
This function is optional function.
(2) Control method

The following block diagram shows the general method of dual
position feedback control:
Separate
ER1 Position gain Motor detector
MCMD + + ER + Velocity
Σ Kp Amplifier
control
− + −
Velocity feedback
Conversion
coefficient
Position feedback (from motor)
ER2
+ − Primary delay
Σ
time constant
− +
Position feedback (from separate detector)

Fig. 4.5.8 Block diagram of dual position feedback control
As shown in Fig. 4.5.8, error counter ER1 in the semi-closed loop

system and error counter ER2 in the closed loop system are used. The
primary delay time constant is calculated as follows:
Primary delay time constant = (1 + τs)−1
The actual error, ER, depends on the time constant, as described
below:
(1) When time constant τ is 0 ⋅⋅⋅⋅⋅⋅ (1 + τs)−1 = 1
ER = ER1 + (ER2 − ER1) = ER2 (error counter of the full-closed
loop system)
(2) When time constant τ is ∞ ⋅⋅⋅⋅⋅⋅ (1 + τs)−1 = 0
ER = ER1 (error counter of the semi-closed loop system)
This shows that control can be changed according to the primary delay
time constant. The semi-closed loop system applies control at the
transitional stage and the full-closed loop system applies control in
positioning.
This method allows vibrations during traveling to be controlled as in
the semi-closed loop system.
- 189 -

(Series 15i-B,16i-B,18i-B,21i-B,Power Mate i)

#7 #6 #5 #4 #3 #2 #1 #0
1709 (FS15i) DPFB
2019 (FS30i, 16i)
DPFB (#7) 1: To enable dual position feedback
1861 (FS15i) Dual position feedback maximum amplitude

2049 (FS30i, 16i)
[Setting value] Maximum amplitude (µm)/(minimum detection unit for full-closed
mode × 64)
This parameter should normally be set to 0.
[Unit of data] Minimum detection unit for full-closed mode (µm/p) × 64
If setting = 0, compensation is not clamped. If the parameter is
specified, and a position error larger than the specified value occurs
during semi-closed and full-closed modes, compensation is clamped.
So set the parameter with a value two times the sum of the backlash
and pitch error compensation amounts.
If it is impossible to find the sum, set the parameter to 0.
1971 (FS15i) Dual position feedback conversion coefficient (numerator)

2078 (FS30i, 16i)
1972 (FS15i) Dual position feedback conversion coefficient (denominator)

2079 (FS30i, 16i)
[Setting value] Reduce the following fraction and use the resulting irreducible
fraction.
Number of position feedback pulses
per motor revolution
Conversion Numerator
(Value multiplied by the feed gear)
coefficient ( ) =
Denominator 1 million
With this setting method, however, cancellation in the servo software
internal coefficient may occur depending on constants such as the
machine reduction ratio, causing the motor to vibrate. In such a case,
the setting must be changed.
For details, see Art. (6) in this section.
- 190 -
(Example)
When the αi Pulsecoder is used with a tool travel of 10
mm/motor revolution (1 µm/pulse)
Conversion Numerator 10 × 1000 1
coefficient ( ) = =
Denominator 1,000,000 100
1973 (FS15i) Dual position feedback primary delay time constant

2080 (FS30i, 16i)
[Setting value] Set to a value in a range of 10 to 300 msec or so.
[Unit of data] msec
Normally, set a value of around 100 msec as the initial value. If
hunting occurs during acc./dec., increase the value in 50-msec steps. If
a stable status is observed, decrease the value in 20-msec steps. When
0 msec is set, the same axis movement as that in full-closed mode is
performed. When 32767 msec is set, the same axis movement as that
in semi-closed mode is performed.
For a system that requires simultaneous control of two axes, use the
same value for both axes.
1974 (FS15i) Dual position feedback zero-point amplitude

2081 (FS30i, 16i)
[Setting value] Zero width (µm)/minimum detection unit for full-closed mode
[Unit of data] Minimum detection unit (µm/p) for full-closed mode
Positioning is performed so that the difference in the position between
full-closed mode and semi-closed mode does not exceed the pulse
width that corresponds to the parameter-set value.
First set the parameter to 0. If still there is fluctuation, increase the
parameter value.
If this is applied to an axis with a large backlash, a large position error
may remain. For details, see Art. (5) in this section.
1729 (FS15i) Dual position feedback: Level on which the difference in error between the
semi-closed and full-closed modes becomes too large
2118 (FS30i, 16i)
[Setting value] Level on which the difference in error is too large (µm)/minimum
detection unit for full-closed mode
[Unit of data] Minimum detection unit (µm/p) for full-closed mode
If the difference between the Pulsecoder and the separate detector is
greater than or equal to the number of pulses that corresponds to the
value specified by the parameter, an alarm is issued.
Set a value two to three times as large as the backlash.
When 0 is set, detection is disabled.
- 191 -
NOTE
The function for monitoring the difference in error
between the semi-closed and full-closed modes is
useful also for monitoring for a problem such as the
feedback pulse missing of a separate detector.
When only the monitoring of the difference in error
between the semi-closed and full-closed modes is
to be performed on a machine for which dual
position feedback is not required as a stabilization
function, the function for monitoring the difference
in error between the semi-closed and full-closed
modes can be used by not only making an ordinary
full-closed loop setting but also setting a
conversion coefficient for dual position feedback
and the parameter for the monitoring level of the
difference in error between the semi-closed and
full-closed modes. (No option setting and function
bit setting need to be made.)
#7 #6 #5 #4 #3 #2 #1 #0
1954 (FS15i) HBBL HBPE
2010 (FS30i, 16i)
HBBL (#5) The backlash compensation is added to the error count of:
0: The semi-closed loop. (Standard setting)
1: The closed loop.
HBPE (#4) The pitch error compensation is added to the error count of:
0: The closed loop. (Standard setting)
1: The semi-closed loop.
#7 #6 #5 #4 #3 #2 #1 #0
1746 (FS15i) HBSF
2206 (FS30i, 16i)
HBSF (#4) A backlash compensation and pitch error compensation are:
0: Added after selection according to the conventional parameter
(No. 1954 (Series 15i) or No. 2010 (Series 30i, 16i, and so on)).
1: Added to the closed loop side and semi-closed loop side at the
same time.
When this parameter is set to 1, the settings of No. 1954 (Series 15i)
and No. 2010 (Series 30i, 16i, and so on)are ignored.
- 192 -
NOTE
1 If a setting is made to perform the function for monitoring the
difference in error between the semi-closed and full-closed
modes for an axis placed in a simple full-closed loop, the
specification for addition of a backlash compensation and
pitch error compensation is the same as in the case of using
the dual position feedback function. In this case, it is
recommended to make the setting above to "Add a backlash
compensation and pitch error compensation to the closed
loop side and semi-closed loop side at the same time".
2 When the dual check safety function is used with Series 16i,
18i, or 21i, a conversion coefficient for dual position
feedback is used. In this case as well, make the setting
above to "Add a backlash compensation and pitch error
compensation to the closed loop side and semi-closed loop
side at the same time".
(5) Use with smooth backlash compensation

With the Series 30i/31i/32i, a smooth backlash compensation value
can be added onto the semi-closed side by setting the parameter
indicated below to 1 when the dual position feedback function is used
together with smooth backlash compensation.
[Applicable servo software]

Series 90D0/Q(17) and subsequent editions
Series 90E0/Q(17) and subsequent editions
[Applicable system software]

- Version 29.0 or later is usable for the following series:
FS30i-A : G002, G012, G022, G032
FS31i-A5 : G121, G131
FS31i-A : G101, G111
FS32i-A : G201
- Version 12.0 or later is usable for the following series:
FS30i-A : G003, G013, G023, G033
FS31i-A5 : G123, G133
FS31i-A : G103, G113
FS32i-A : G203
#7 #6 #5 #4 #3 #2 #1 #0
- SBN
11601(FS30i)
SBN (#6) When both of smooth backlash compensation and dual position
feedback are enabled, a smooth backlash compensation value is:
1: Used for compensation on the semi-closed side.
0: Dependent on the settings of bit 4 of No. 2206 and bit 5 of No.
2010.
- 193 -
(6) Zero-width setting for a machine with a large backlash or twist

Dual position feedback function (or hybrid function) is used for an
axis where a machine backlash of about 1/10 revolution in terms of
the motor shaft exists, the machine may stop with a position error
remaining, which is greater than the dual position feedback zero-width
parameter value. (In some cases, there may be ten or more pulses left.)
To solve this problem, make the following settings:
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) DUAL0W
2202 (FS30i, 16i)
DUAL0W (#4) The zero-width determination is performed with:
0: Semi-full error only.
1: Both of the position error on the full-closed side and semi-full
error. ← Set this value.
- 194 -
(7) Cautions on setting of the dual position feedback conversion coefficient
CAUTION
The dual position feedback conversion coefficient
is set as explained in Art. (4). With the conventional
calculation method, however, cancellation may
occur in the conversion coefficient of the servo
software depending on constants such as the
machine deceleration ratio. If cancellation in the
conversion coefficient occurs, feedback errors in
the semi-closed loop system are accumulated. In
some cases, this may result in motor oscillation.
To prevent this problem, calculate and set the dual
position feedback conversion coefficient by
following the procedure given below.
Number of position feedback pulses per motor revolution

n (Value after multiplication of F⋅FG)
Reduce the following fraction: =
d 1,000,000
n
Is A = 8,000,000 × an integer?
d
No Yes
Obtain the smallest m so that the result of m × A is an integer.
Follow the setting procedure shown below. Set the following

This setting reduces the detection unit by a factor of m. (conventional method):
<1> Reduce the following: Conversion coefficient (numerator) n
Conversion coefficient (numerator) n =
= ×m Conversion coefficient (denominator) d
Conversion coefficient (denominator) d
<2> Multiply CMR by m.
<3> Reduce the following:
F⋅FG (numerator) Current F⋅FG (numerator)
= ×m
F⋅FG (denominator) Current F⋅FG (denominator)
<4> Multiply the reference counter capacity by m.
<5> Multiply the effective area by m.
<6> Multiply the positional deviation threshold during movement by m.
<7> Multiply the positional deviation threshold in the stop state by m.
<8> Multiply the backlash by m.
<9> Multiply the scale factor of the pitch error compensation by m.
* For parameters set in detection units, see the list in Appendix B.
- 195 -
4.5.9 Machine Speed Feedback Function
(1) Overview
In many full-closed systems, the machine position is detected by a
separate detector and positioning was controlled according to the
detected positioning information. The speed is controlled by detecting
the motor speed with the Pulsecoder on the motor. When distortion or
shakiness between the motor and the machine is big, the machine
speed differs from the motor speed during acceleration and
deceleration. Hence, it is difficult to maintain high position loop gain.
This machine speed feedback function allows adding the speed of the
machine itself to the speed control in a fully closed system, making
the position loop stable.

(3) Control block diagram

Fig. 4.5.9 is a control block diagram
PK1V: velocity loop integral gain Machine speed
PK2V: velocity loop proportional gain
α : machine speed feedback gain
Machine
PK2V × α 1/(JL • s) 1/s
Spring coupling
MCMD + VCMD + + −
Kp PK1V/s + PK2V 1/(Jm • s)
+ − − TCMD
Motor
Speed feedback
Position feedback
Fig. 4.5.9 Position loop block diagram that includes machine speed feedback function
As shown in Fig. 4.5.9, this function corrects the torque command by

multiplying the machine speed by machine velocity feedback gain, α,
as shown by the bold line. When α = 1, the torque command is
corrected equally by the motor speed and the machine speed.
- 196 -
(4) Adding the normalization function

(a) Overview
If an arc is drawn with the machine speed feedback function
enabled, the arc may be elongated in the direction parallel to the
axis to which the machine speed feedback function is applied.
To solve this problem, the machine speed feedback function was
improved.
(b) Explanation
Motor Machine
Speed feedback
Motor speed at the tip of the
feedback machine
α
Speed feedback for

proportional terms + +
The current machine speed feedback configuration is as shown above

figure. Assuming that the motor speed feedback is much the same as
the speed feedback at the tip of the machine, the speed feedback for
the proportional term is (1 + α) times the motor speed feedback. This
causes a conflict to the weight of the VCMD.
So, the proportional term speed feedback is divided by (1 + α) to eliminate
the conflict.
* The normalization function cannot be used when the velocity

loop proportional high-speed processing function is used.

#7 #6 #5 #4 #3 #2 #1 #0
1956 (FS15i) MSFE
2012 (FS30i, 16i)
MSFE (#1) 1: To enable the machine speed feedback function
1981 (FS15i) Machine speed feedback gain (MCNFB)

2088 (FS30i, 16i)
• When a serial output type separate detector is used or when the

flexible feed gear (parameters Nos. 2084 and 2085, parameter
Nos. 1977 and 1978) is set to 1/1
(Setting range: 1 to 100 or −1 to −100)
(Typical setting)
When the normalization function is not used: MCNFB = 30 to 100
When the normalization function is used: MCNFB = −30 to −100
• Other than flexible feed gear (No. 2084, 2085, 1977, 1978) = 1/1
(Setting range: 101 to 10000 or −101 to −10000)
(Typical setting)
When the normalization function is not used: MCNFB = 3000 to 10000
When the normalization function is used: MCNFB = −3000 to −10000
- 197 -
(6) Note
It the machine has a resonance frequency of 200 to 400 Hz, using this
function may result in a resonance being amplified, thus leading to
abnormal vibration or sound. If this happens, take either of the
following actions to prevent resonance.
• Using an observer (⇒ Subsec. 4.5.6)
(If the machine speed feedback function is used together with the
observer function, the motor speed and machine speed are
filtered out simultaneously.)
• Using a torque command filter (⇒ Subsec. 4.5.2)
- 198 -
4.5.10 Machining Point Control
(1) Overview
The machining point control function suppresses vibration after
positioning by attaching an acceleration sensor to the machining point
and using acceleration feedback for control.
NOTE
Machining point control uses an acceleration
sensor. For the setting of an acceleration sensor,
see Subsection 2.1.7.

(Series 16i-B,18i-B,21i-B,0i-B,0i Mate-B, Power Mate i)

（a）Setting machining point control
(Function bit setting)
To use machining point control, enable the following function bit:
#7 #6 #5 #4 #3 #2 #1 #0
- MPCEF
2288(FS30i,16i)
MPCEF(#7) Machining point control is:
0: Disabled
1: Enabled
（Band-pass filter setting)

When gain is tuned for machining point control, components other
than a vibration suppression target frequency may cause vibration to
disable a high gain value from being set. To extract a vibration
suppression target frequency component only, be sure to set the
vibration suppression target frequency component in the following
parameter:
- Machining point control/center frequency of band-pass filter

2355(FS30i,16i)
[Unit of data] Hz
NOTE
If the value 4 or a smaller number is set, an illegal
parameter setting alarm (detail number 3553 or
3603) is issued. Set the value 5 or a greater number.
- 199 -
（b）Tuning machining point control

Three parameters are available for tuning machining point control. By
tuning these parameters, vibration after specified
acceleration/deceleration can be suppressed.
• Gain 1
• Timing adjustment parameter
• Gain 2
（Tuning of machining point control gain 1)

Tune machining point control gain 1 so that the acceleration rate
(enclosed by the dashed line in the figure below) after
acceleration/deceleration based on specified acceleration decreases.
Tune machining point control gain 1, starting with a small value
(about 50).
- Machining point control gain 1 (MPCK1)

2266(FS30i,16i)

Machining point control disabled Machining point control enabled (after tuning gain 1)
Acceleration caused by
machine vibration
Acceleration Acceleration
Velocity Velocity
Acceleration caused
by motion command
（Tuning of the timing adjustment parameter)

Tune the machining point control timing adjustment parameter so that
the acceleration rates (enclosed by the dashed lines in the figure
below) after acceleration/deceleration based on specified acceleration
decrease.
This timing adjustment is implemented with a low-pass filter applied
to feedback. Set the parameter so that the cut-off frequency of the
filter is around the frequency of vibration.
After the setting of the timing adjustment parameter is modified, gain

1 needs to be tuned again. To obtain an optimum vibration
suppression effect, tune the timing adjustment parameter and gain 1
repeatedly.
- 200 -
Machining point control enabled

(after tuning of gain 1 and the timing adjustment parameter)
Acceleration
Velocity
- Machining point control timing adjustment parameter (MPCTIM)

2096(FS30i,16i)
[Typical setting] The setting of the parameter corresponds to the cut-off frequency of
the low-pass filter.
Set the parameter so that the cut-off frequency is around the frequency
of vibration.
Cut-off Parameter Cut-off Parameter

frequency [Hz] setting frequency [Hz] setting
5 3969 17.5 3669
7.5 3907 20 3612
10 3847 25 3501
12.5 3787 30 3392
15 3728 40 3186
NOTE
When 0 is set in the parameter, the cut-off
frequency of the filter is 40 Hz.
(Tuning of machining point control gain 2)

By tuning machining point control gain 2, vibration may be further
suppressed.
While checking the effect of vibration suppression, tune machining
point control gain 1 and machining point control gain 2 repeatedly.
Tune machining point control gain 2, starting with a small value about
10).
- Machining point control gain 2 (MPCK2)

2265(FS30i,16i)
- 201 -
4.6 CONTOUR ERROR SUPPRESSION FUNCTION
4.6.1 Feed-forward Function
(1) Principle
s Smoothing VFF • s
α
+ + +
Position Position gain Velocity loop Servo motor
command − + +
α: Feed-forward coefficient (0 to 1)
VFF: Velocity loop feed-forward coefficient
Fig. 4.6.1 (a) Feed-forward control block diagram
Adding feed-forward term α to the above servo system causes the

position error to be multiplied by (1 - α).
Feedrate (mm/s)
Position error = × (1 - α)
Minimum detection unit (mm) × position gain
Adding feed-forward term α also causes figure error ∆R1 (mm) due to
a radial delay of the servo system during circular cutting to be
multiplied by (1 - α2).
Feedrate2 (mm/s)2
∆R1 (mm) = × (1 - α2)
2
2 × position gain × radius (mm)
(Example) If α = 0.7, ∆R1 is reduced to about 1/2.
Beside ∆R1, figure error ∆R2 (mm) may occur in a position command
when an acc./dec. time constant is applied after interpolation for two
axes.
Therefore, total radial figure error ∆R during circular cutting is:
∆R = ∆R1 + ∆R2
This section describes the conventional feed-forward function.

However, when using feed-forward for high-speed and high precision
machining, be sure to use advanced preview feed-forward described in
Subsec. 4.6.2 or RISC feed-forward described in Subsec. 4.6.3.
The shape error in the direction of the radius during circular cutting is
as shown in Fig. 4.6.1 (b) below.
- 202 -
Start point
∆R2 (Error as a result of acceleration and

deceleration after interpolation.)
∆R1 (Error as a result of servo series delay.)
Program path
Command path
Actual path
Fig. 4.6.1 (b) Path error during circular cutting

Series 90D0/A(01) and subsequent editions(*)
Series 90E0/A(01) and subsequent editions(*)
(*) With Series 90D0 and 90E0, the advanced preview feed-forward
function is applied unless the EGB synchronous mode is set.
- 203 -

<1> Enable PI control and the feed-forward function.
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) PIEN
2003 (FS30i, 16i)
PIEN (#3) 1: To enable PI control
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) FEED
2005 (FS30i, 16i)
FEED (#1) 1: To enable the feed-forward function
<2> Specify the feed-forward coefficient.
1961 (FS15i) Feed-forward coefficient (FALPH)

2068 (FS30i, 16i)
FALPH = α × 100 or α × 10000
When FALPH is smaller than or equal to 100: In units of 1%

When FALPH is greater than 100: In units of 0.01%
[Typical setting] 70 or 7000
<3> Specify the velocity feed-forward coefficient.
1962 (FS15i) Velocity feed-forward coefficient (VFFLT)

2069 (FS30i, 16i)
VFFLT = 50 (50 to 200)
<4> Run a program to move the axis for cutting feed at maximum
feedrate. Under this condition, check whether the VCMD
waveform observed on the Servo Guide or the servo check board
overshoots and what the shock caused during acceleration
/deceleration is like.
⇒ If an overshoot occurs, or the shock is big, increase the
acc./dec. time constant, or reduce α.
⇒ If an overshoot does not occur, and the shock is small, reduce
the acc./dec. time constant, or increase α.
Linear acc./dec. is more effective than exponential acc./dec.
Using acc./dec. before interpolation can further reduce the figure
error.
- 204 -
<5> By setting the parameter below, the feed-forward function can be

used for cutting feed as well.
#7 #6 #5 #4 #3 #2 #1 #0
1800 (FS15i) FFR
1800 (FS30i, 16i)
FFR (#3) Specifies whether feed-forward control during rapid traverse is
enabled or disabled.
0: Disabled
1: Enabled
By using the feed-forward function during rapid traverse, the

positioning time can be reduced. On some machines, however, a
shock may occur at the time of acc./dec. In such a case, use fine
acc./dec. (⇒ Subsec. 4.8.3) at the same time, or make
adjustments such as increasing the acc./dec. time constant.
Moreover, a feed-forward coefficient can be set separately for
each of cutting and rapid traverse. (See Subsection 4.6.4,
"Cutting/Rapid Feed-forward Switching Function".)
<6> To use the EGB function, set the following parameter:
#7 #6 #5 #4 #3 #2 #1 #0
1955 (FS15i) FFAL
2011 (FS30i, 16i)
FFAL (#1) Feed-forward control is:
1: Always enabled regardless of the mode.
- 205 -
4.6.2 Advanced Preview Feed-forward Function
(1) Overview
The advanced preview feed-forward function is part of the advanced
preview control function. It enables high-speed and high precision
machining. The function creates feed-forward data according to a
command which is one distribution cycle ahead, and reduces the delay
caused by smoothing. This new function can upgrade the high-speed,
high precision machining implemented under conventional
feed-forward control. The conventional feed-forward control function
executes smoothing in order to eliminate the velocity error of each
distribution cycle (see Fig. 4.6.2 (a)). This smoothing, however,
causes a delay in the feed-forward data.
The new advanced preview feed-forward control function uses the
distribution data which is one distribution cycle ahead and generates
delay-free feed-forward data (Fig. 4.6.2 (b)). The function can provide
higher controllability than the conventional feed-forward control
function.
NC command NC command
Feed-forward data under

Feed-forward data advanced preview feed-
forward control
Fig. 4.6.2 (a) Conventional feed-forward control Fig. 4.6.2 (b) Advanced preview feed-forward control


<1> Set the following parameters in the same way as for conventional
feed-forward control.
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) PIEN
2003 (FS30i, 16i)
PIEN (#3) 1: PI control is selected.
- 206 -
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) FEED
2005 (FS30i, 16i)
FEED (#1) 1: The feed-forward function is enabled.
1962 (FS15i) Velocity feed-forward coefficient (VFFLT)

2069 (FS30i, 16i)
[Recommended value] 50 (50 to 200)
<2> Set the coefficient for advanced preview feed-forward control.
1985 (FS15i) Advanced preview feed-forward coefficient (ADFF1)

2092 (FS30i, 16i)
Advanced preview feed-forward coefficient (0.01% unit)
= α × 10000 (0 ≤ α ≤ 1)
(Example)
When α equals 98.5%, ADFF1 is 9850.
Advanced preview control is configured as shown below:
Deceleration algorithm and function of acc./dec.
before interpolation of CNC
• Acc./dec. method causing no figure errors
Advanced • Deceleration at a point where a large impact
preview would be expected
control Advanced preview feed-forward function of
digital servo
• Improving the tracking ability of the servo
system
Because of this configuration, the function can improve the
feed-forward coefficient up to about 100% without impact and
also reduce figure error.
<3> By specifying the G codes listed below, the modes related to

high-speed and high precision machining such as advanced
preview control can be turned on/off. In each mode, advanced
preview feed-forward is enabled.
NOTE
While the fine acc./dec. (FAD) function is being
used, the advanced preview feed-forward function is
always used, and the advanced preview
feed-forward function cannot be turned on and off
by G codes.
- 207 -
G code
Mode
Mode ON Mode OFF
G08P1 G08P0 Advanced preview control mode
Acc./dec. mode before look-ahead
interpolation
G05.1Q1 G05.1Q0 AI nano-contour control mode
AI contour control mode
AI advanced preview control mode
High-precision contour control
(⇒ Subsec.4.6.3)
G05P10000 G05P0 AI high precision contour control
AI nano high precision contour control
Fine HPCC
AI contour control I mode
G05.1Q1 G5.1Q0
AI contour control II mode
* With the Series 30i/31i/32i (servo software Series 90D0 and
90E0), the advanced preview feed-forward function is always
applied regardless of G codes.
* For a CNC that supports this function, see Appendix D.
(Example)
G08P1; Advanced preview control mode on
...
... Advanced preview feed-forward enabled
...
G08P0; Advanced preview control mode off
- 208 -
4.6.3 RISC Feed-forward Function
(1) Overview
The feed-forward system is used during high precision contour control
based on RISC (HPCC mode) or AI contour control (AICC mode) in
order to shorten the interpolation cycle, improving the performance of
high-speed, high precision machining.
(This function is insignificant for AI nano-contour control complying
with nano-interpolation as a distribution system, AI high-precision
contour control, AI nano high-precision contour control, and fine
HPCC.)
By using this function, the response of the servo side can be improved
when the distribution period is 4 ms, 2 ms, or 1 ms.

Series 9096/A(01) and subsequent editions(*)
(*) Series 9096 supports distribution periods of 1 ms and 2 ms only,

and it does not support 4 ms.

<1> Set the following parameters in the same way as for the advanced
preview feed-forward function.
<2> Set the parameters (RISCFF and RISCMC) below.
#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) RISCFF
2017 (FS30i, 16i)
RISCFF (#5) 0: Feed-forward response remains unchanged when RISC is used.
1: Feed-forward response improves when RISC is used.
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) RISCMC
2200 (FS30i, 16i)
RISCMC (#5) When RISC is used:
0: Feed-forward response remains unchanged.
1: Feed-forward response improves.
- 209 -
<3> By specifying a G code in the program, each mode is enabled,

and the advanced preview feed-forward function set above is
applied.
G code
Mode
Mode ON Mode OFF
G05.1Q1 G05.1Q0 AI contour control mode
G05P10000 G05P0 HPCC mode
* Appendix D lists the supported CNCs.
If the modes above are off, the normal feed-forward coefficient is

enabled.
NOTE
1 Use this function only when very high command
response is required.
2 When using this function, set a detection unit of 0.1
µm wherever possible.
(To set a detection unit of 0.1 µm, the IS-C system
must be used, or the CMR and flexible feed gear
must be multiplied by 10 with the IS-B system.)
- 210 -
4.6.4 Cutting/Rapid Feed-forward Switching Function
(1) Overview
To use a separate feed-forward coefficient for each of cutting feed and
rapid traverse, the use of the cutting/rapid fine acc./dec. switching
function has been required conventionally. The cutting feed/rapid
traverse switchable feed-forward function allows a separate coefficient
to be used for each of cutting feed and rapid traverse, without using
the cutting feed/rapid traverse switchable fine acc./dec. function.

(3) Cautions
This function is usable with the modes below. Note that this function
cannot be used with the normal mode.
[Usable modes]
• Advanced preview control mode
• AI contour control mode
• AI nano contour control mode
• High precision contour control mode
• AI high precision contour control mode
• AI nano high precision contour control mode
(*) With the Series 30i/31i/32i, this function can be used regardless
of the specified mode.

<1> First, set the parameters below in the same way as for the current
feed-forward function.
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) PIEN
2003 (FS30i, 16i)
PIEN(#3) 1: A switch is made to PI control.
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) FEED
2005 (FS30i, 16i)
FEED (#1) 1: The feed-forward function is enabled.
- 211 -
<2> Next, set the cutting/rapid feed-forward switching function.
#7 #6 #5 #4 #3 #2 #1 #0
2602 (FS15i) FFCHG
2214 (FS30i, 16i)
FFCHG (#4) 1: The cutting/rapid feed-forward switching function is enabled.
<3> With the setting of the parameters above, the parameters below
are enabled in cutting.
1768 (FS15i) Velocity feed-forward coefficient for cutting

2145 (FS30i, 16i)
1767 (FS15i) Advanced preview feed-forward coefficient for cutting

2144 (FS30i, 16i)
The parameters below are enabled in rapid traverse.

1962 (FS15i) Velocity feed-forward coefficient for rapid traverse
2069 (FS30i, 16i)
1985 (FS15i) Advanced preview feed-forward coefficient for rapid traverse

2092 (FS30i, 16i)
- 212 -
4.6.5 Feed-forward Timing Adjustment Function
(1) Overview
If the feed-forward function is applied with the aim of decreasing
contour errors, the same feed-forward coefficient must be used for all
axes. Even if a unified feed-forward coefficient is used, however, the
axes may not necessarily behave in the same manner because of
differences in the mechanical characteristic and velocity loop response
among the axes.
The feed-forward timing adjustment function is intended to change the
feed-forward timing so as to make the characteristics of each axis at
high-speed movement. It does not change the feed-forward coefficient.
So it can change the characteristic of a portion where the acceleration
is high without affecting the operation for straight portions.
If the radius of an arc subjected to high-speed cutting differs among
axes, resulting in a vertical or horizontal oval, this function is useful in
improving roundness through fine adjustment.
(2) Control method

When an arc is cut at high speed, delaying the feed-forward timing
causes the path to bulge. On the contrary, advancing the feed-forward
timing causes the path to shrink. The feed-forward timing adjustment
function lets you make fine adjustments on the characteristic of servo
axes.
Let the radius, feedrate, and position gain be, respectively, R, V, and
Kp. Delaying the feed-forward timing by τ(s) increases the radius of
the arc by:
∆R = τ×V2/(Kp×R)
To be specific, assume radius R = 10 mm, feedrate V = 4000 mm/min,
and position gain Kp = 40/s. Shifting the timing by 1 ms corresponds
to:
∆R = 11 µm

- 213 -

#7 #6 #5 #4 #3 #2 #1 #0
－ IAHDON
2415(FS30i)
IAHDON(#1) The default value of the feed-forward timing adjustment parameter is:
0: Feed-forward timing is adjusted by only No. 2095.
1: Compatible with that of Series 16i. (See the table below.)
* By setting IAHDON=1 and No. 2095=0, the feed-forward timing
becomes compatible with that of Series 16i.
The actually applied feed-forward timing is "setting of No. 2095 +
default value".
When newly setting bit 1 of No. 2415 to 1 for a system that already
has a value set in No. 2095, set a value calculated from the following
formula in No. 2095:
No.2095 (new setting) =
No.2095 (value determined by setting bit 1 of No. 2415 to 0) -
default value (table below)
Default feed-forward timing value
No.2415#1=0 No.2415#1=1
HRV2 control 0 3900
HRV3 control 0 3900
HRV4 control 0 3792 (*1)
(*1) When HRV4 control is used and any of the following functions
is used, the default value is -240:
• High-speed processing
• AI contour control II
• High-speed cycle machining
Series and editions of applicable servo software
1988 (FS15i) Feed-forward timing adjustment coefficient

2095 (FS30i, 16i)
Specifying +4096 causes the feed-forward timing to advance by 1 ms.
Specifying -4096 causes the feed-forward timing to delay by 1 ms.
If you want to decrease the radius of an arc at high-speed cutting,
increase the coefficient by about 300 at each step.
If you want to increase the radius of an arc at high-speed cutting,
decrease the coefficient by about 300 at each step.
This parameter is valid for advanced preview feed-forward control
(parameter Nos. 1985 and 1767 (Series 15i) and parameter Nos. 2092
and 2144 (Series 30i, 16i, and so on). It is invalid for conventional
feed-forward control type (parameter No. 1961 (Series 15i) and
parameter No. 2068 (Series 16i and so on)).
With the following servo software, the feed-forward timing slightly
differs when the fine acc./dec. function is used, so a separate
parameter is prepared for independent setting.
- 214 -

Series 90B0/J(10) and subsequent editions
2808 (FS15i) Feed-forward timing adjustment coefficient (to be used when fine acc./dec.
is enabled)
2395 (FS30i, 16i)
* If fine acc./dec. is specified and is used in one of the following

modes:
• Simple cutting feed (no high-precision mode)
• Advanced preview control
• AI advanced preview control (Series 21i)
This parameter can set the timing adjustment coefficient to
parameter No. 1988 + parameter No. 2808 (for the Series 15i)
and
parameter No. 2095 + parameter No. 2395 (for the Series 16i and
so on).
In other high definition modes (modes in which fine acc./dec. is
disabled, such as AI contour control), the timing adjustment
coefficient is set to
parameter No. 1988 (for the Series 15i)
parameter No. 2095 (for the Series 16i and so on).
This parameter allows setting of different timing adjustment
coefficients depending on whether fine acc./dec. is enabled or
disabled.
- 215 -
4.6.6 Backlash Acceleration Function
(1) Overview
If the influence of backlash and friction is large in the machine, a
delay may be produced on reversal of motor, thus resulting in
quadrant protrusion on circular cutting.
This is a backlash acceleration function to improve quadrant
protrusion.

Backlash acceleration function
Override function
Series 90B0/W(23) and subsequent editions

<1> Set the backlash compensation.
1851 (FS15i) Backlash compensation

1851 (FS30i, 16i)
In semi-closed mode:
Set the machine backlash. (Minimum value = 1)
In full-closed mode:
Set the minimum value of 1. When the backlash
compensation value is not to be reflected in the position,
enable the function below additionally.
NOTE
Be sure to set a positive backlash compensation value.
(Tip)
See the supplement on backlash compensation
value setting provided at the end of Item (3).
- 216 -
#7 #6 #5 #4 #3 #2 #1 #0
1884 (FS15i) FCBL
2006 (FS30i, 16i)
FCBL (#0) Backlash compensation is not performed for the position in the
full-closed mode.
0: Invalid
1: Valid
Generally, for a machine in full-closed mode, backlash compensation

is not reflected in positions, so this bit is set. (This parameter is
applicable also to a machine with a semi-closed loop.)
<2> Enable the backlash acceleration function.

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) BLEN
2003 (FS30i, 16i)
BLEN (#5) 1: To enable backlash acceleration
1860 (FS15i) Backlash acceleration amount

2048 (FS30i, 16i)
Offset for the velocity command that is to be added immediately after
a reverse.
1964 (FS15i) Period during which backlash acceleration remains effective

(in units of 2 msec)
2071 (FS30i, 16i)
The period during which the acceleration amount is added. At the start
of adjustment, set 20. When a long quadrant protrusion is found,
gradually increase the setting in steps of 10.
<3> When the optimum backlash acceleration amount varies with the
machining feedrate, use the acceleration amount override and the
limit of the acceleration amount.
1725(FS15i) Acceleration amount override

2114(FS30i, 16i)
2751(FS15i) Limit of acceleration amount

2338(FS30i, 16i)
[Valid data range] 0 to 32767 (When 0 is set, the acceleration amount is not limited.)
[Example] Example of setting the acceleration amount when a model such as the
Series 16i is used
Acceleration amount (parameter No. 2048) = 46, acceleration amount
override (parameter No. 2114) = 23, limit of acceleration amount
(parameter No. 2338) = 500
- 217 -
Backlash acceleration amount

Backlash acceleration amount when override is set
600
500
400
300
200
100
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
Feedrate (mm/min)
<4> Setting the direction-based backlash acceleration function

When the optimum acceleration amount differs between a reverse
operation in the positive direction and a reverse operation in the
negative direction, set the acceleration amount used for the
reverse operation from the negative direction to positive direction
in the following parameter:
1987(FS15i) Backlash acceleration amount (for reverse from negative to positive

direction)
2094(FS30i, 16i)
2753(FS15i) Acceleration amount override (for reverse from negative to positive

direction)
2340(FS30i, 16i)
2754(FS15i) Limit of acceleration amount (for reverse from negative to positive direction)
2341(FS30i, 16i)
[Valid data range] 0 to 32767 (When 0 is set, the acceleration amount is not limited.)
[Parameters used for direction-based setting]

Series30i,16i, and so on
Direction-based Reverse Backlash Acceleration Limit of acceleration
setting direction acceleration amount amount override amount
None Common
No. 2048 No. 2114 No. 2338
From + to -
Present
From - to + No. 2094 No. 2340 No. 2341
Series 15i
Direction-based Reverse Backlash Acceleration Limit of acceleration
setting direction acceleration amount amount override amount
None Common
No. 1860 No. 1725 No .2751
From + to -
Present
From - to + No. 1987 No. 2753 No. 2754
- 218 -
<5> If a reverse cut occurs, use the backlash acceleration stop

function.
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) BLST
2009 (FS30i, 16i)
BLST (#7) 1: To enable the backlash acceleration stop function
NOTE
When the backlash acceleration stop function is
enabled (with BLST = 1), be sure to set a positive
value in the backlash acceleration stop timing
parameter described below. (If 0 or a negative
value is set, backlash acceleration is not
performed.)
1975(FS15i) Backlash acceleration stop distance

2082(FS30i,16i)
[Typical setting] 2 to 5 (detection unit of 1µm), 20 to 50 (detection unit of 0.1µm)
This parameter is related to the distance until backlash acceleration
ends. Determine the parameter value by checking the actual profile.
This completes the general setting procedure for the backlash

acceleration function.
- 219 -
(Tip) Supplement on backlash compensation value setting

In an ordinary mode not using FAD (in a mode other than the advanced
preview modes indicated below), the backlash acceleration function is
enabled only when a positive backlash compensation value is set. In the
advanced preview modes indicated below, the backlash acceleration function
is enabled, regardless of the setting of a backlash compensation value.
When FAD is used, an ordinary mode is treated in the same way as the
advanced preview modes. So, the backlash acceleration function is enabled,
regardless of the setting of a backlash compensation value.
Ｇ code
Mode
Mode ON Mode OFF
Look-ahead acc./dec. mode before interpolation
AI nano contour control mode
G05.1Q1 G05.1Q0
High-precision contour control (⇒ Subsec.4.6.3)
AI high-precision contour control
G05P10000 G05P0
AI nano high-precision contour control
Fine HPCC
AI advanced preview control I mode
G05.1Q1 G5.1Q0
AI advanced preview control II mode
* With the Series-30i/31i/32i (servo software Series 90D0 and 90E0), advanced
preview feed-forward is applied, not based on G code, at all times.
* For the applicable CNCs, see Appendix D.

There are two methods for setting the acceleration amount override as
listed below. Normally, use setting method 1.
• Setting method 1 (calculation not required)

<1> With an assumed minimum acceleration, obtain the
optimum backlash acceleration amount while observing
quadrant protrusions. Set the obtained value as the backlash
acceleration amount (setting).
<2> Set the acceleration to a middle point between the minimum
and maximum levels, and while increasing the override
value, observe quadrant protrusions to determine the
optimum override value.
<3> Finally, set the maximum acceleration, and observe the arc
figure. If an undercut is generated at the switching point of
quadrants, set the acceleration amount limit to prevent the
acceleration amount from increasing excessively.
- 220 -
• Setting method 2 (strict calculation required)

Obtain an optimum backlash acceleration amount for two
different accelerations (an assumed minimum acceleration and an
intermediate acceleration between the minimum and maximum
accelerations), and substitute the obtained value in the following
equation for the backlash acceleration amount override:
Backlash Backlash Acceleration
× Acceleration
acceleration = acceleration × (1+ amount override )
amount amount (setting) 2048
(Feedrate [mm/min])2 128
Acceleration = ×
Radius [mm] Detection unit [µm] × 1000
Find a solution of the simultaneous equations. The results are as
follows:
(Acceleration amount 2) - (Acceleration amount 1)

Acceleration
amount override = (Acceleration (Acceleration ×2048
amount 1) × (Acceleration 2) - amount 2) × (Acceleration 1)
(Acceleration (Acceleration
amount 1) × × (Acceleration 1)
Backlash acceleration amount (Acceleration 2) -
= amount 2)
(setting)
(Acceleration 2) - (Acceleration 1)
Finally, operate at the maximum acceleration, and adjust the limit of

the acceleration amount.
(5) Ignoring the backlash acceleration function at handle feed

To disable the backlash acceleration function at handle feed, set the
following:
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) BLCU
2009 (FS30i, 16i)
BLCU (#6) 1: To enable the backlash acceleration function during cutting feed
only
NOTE
If bit 3 of parameter No. 1800 is set to 1, the
backlash acceleration function is always enabled,
and it cannot be disabled.
With following series and editions of servo software, the bit shown
below can also be used to enable the backlash acceleration function
only during cutting.
- Series 90B0/C(03) and subsequent editions
- Series 90B5/A(01) and subsequent editions
- Series 90D0/A(01) and subsequent editions
- Series 90E0/A(01) and subsequent editions
Use of this bit enables and disables the backlash acceleration function
even when bit 3 of parameter No. 1800 is set to 1. Backlash
acceleration is enabled even at the hole bottom during rigid tapping.
- 221 -
#7 #6 #5 #4 #3 #2 #1 #0
2611 (FS15i) BLCUT2
2223 (FS30i, 16i)
BLCUT2 (#7) 1: To enable the backlash acceleration function during cutting feed
only
[Reference]
Adjustment the backlash acceleration
Run a program for an arc, and make an adjustment while
checking the arc figure on SERVO GUIDE.
(6) Disabling backlash acceleration after a stop

When using the function for disabling backlash acceleration after a
stop, make the setting below. For details, see "(7) Adjustment of
backlash acceleration" in Appendix H.
#7 #6 #5 #4 #3 #2 #1 #0
2696(FS15i) BLSTP2
2283(FS30i,16i)
BLSTP2(#7) 1: Disables backlash acceleration after a stop.
- 222 -
4.6.7 Two-stage Backlash Acceleration Function
(1) Overview
When the machine reverses the direction of feed, two types of delay
are likely to occur; one type due to friction in the motor and the other
due to friction in the machine.
The two-stage backlash acceleration function compensates for two
types of delays separately, thus enabling two-stage compensation.
First stage: The friction torque is canceled when

Two-stage
the motor reverses.
compensation
Second stage: The friction torque in the machine is
canceled.
Furthermore, optimum compensation can be performed at all times for

first stage against changing speed and load.
The two-stage backlash acceleration function performs compensation
as shown below:
The first stage compensation value is determined automatically.
Specify the parameter to determine how much of the estimated
friction is to be reversed.
First stage acceleration coefficient (normally set to 100%)
Second stage acceleration amount
(if this is 0, second stage does not
occur.)
Second stage
acceleration offset
(Normally, 0 is set.)
Start Time
End
Second stage start and end parameters (detection unit)

The start point of second stage is specified as a distance relative to the
start of first stage.
The end point is determined automatically. Normally, if the setting is
positive, the end point is set at a distance two times greater than the
start point distance. If the setting is negative, the end point is set at a
distance three times greater than the start point distance. An arbitrary
end point can also be set by setting the end scale factor parameter.
Fig. 4.6.7 (a) Backlash acceleration under control of the two-stage
backlash acceleration function

- Two-stage backlash acceleration function
- 223 -

- Limit value in each second-stage acceleration direction

Series 90B0/J(10) and subsequent editions

<1> With SERVO GUIDE, make settings for measuring the motor
speed and estimated disturbance value.
(See Sec. 4.22 for SERVO GUIDE.)
<2> Turn on the power to the NC.
<3> Specify the backlash compensation value.
1851 (FS15i) Backlash compensation value

1851 (FS30i, 16i)
For semi-closed mode, specify the machine backlash (minimum of
1).
For full-closed mode, specify 1. When the backlash compensation
value is not to be reflected in the position, enable the function
below additionally.
NOTE
Be sure to set a positive backlash compensation value.
(Tip)
See the supplement on backlash compensation
value setting provided at the end of Item (3).
#7 #6 #5 #4 #3 #2 #1 #0
1884 (FS15i) FCBL
2006 (FS30i, 16i)
FCBL (#0) Backlash compensation is not performed for the position in the
full-closed mode.
0: Invalid
1: Valid
<4> Adjusting the velocity loop gain

Enable PI control, and increase the velocity loop gain (load
inertia ratio) as much as possible.
(For velocity loop gain adjustment, see Subsec. 3.3.1.)
- 224 -
* By setting a high velocity loop gain, the response of the motor

improves, and quadrant protrusions can be reduced. If the
velocity loop gain is changed in the subsequent adjustments,
the adjustments become complicate. So, increase the velocity
loop gain sufficiently at this stage.
<5> Enable the two-stage backlash acceleration function.

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) BLEN
2003 (FS30i, 16i)
BLEN (#5) 1: To enable the backlash acceleration function
#7 #6 #5 #4 #3 #2 #1 #0
1957 (FS15i) BLAT
2015 (FS30i, 16i)
BLAT (#6) 1: To enable the two-stage backlash acceleration function
<6> Set the observer-related parameters.
(Related parameters)
1862 (FS15i) Observer gain
2050 (FS30i, 16i)
• When HRV1, HRV2, or HRV3 control is used:
[Setting value] No change is required.
• When HRV4 control is used:

2051 (FS30i, 16i)
[Setting value] No change is required.
* When setting an observer gain, follow the settings of other

functions (observer, unexpected disturbance torque detection).
When the two-stage backlash acceleration function is used,
the settings need not be changed.
<7> Adjust observer parameter POA1.

The two-stage backlash acceleration function takes the friction
torque as an estimated disturbance value by using the observer
circuit and determines the first stage acceleration amount.
Therefore, observer parameter POA1 must be adjusted to obtain
correct acceleration. While observing estimated disturbance
value DTRQ, perform acc./dec. to adjust POA1 to the optimum
value.
- 225 -
The procedure for this adjustment is similar to the

procedure for adjusting observer-related
parameters in the unexpected disturbance torque
detection function (Subsection 4.12.1). Make an
adjustment by following steps <5> and <6> in (3),
"Parameter adjustment methods", in Subsection
4.12.1 in this parameter manual. When the
unexpected disturbance torque detection function
is used, and the adjustment has already been
made, re-adjustment is not needed.
1859 (FS15i) Observer parameter (POA1)

2047 (FS30i, 16i)
[Setting value] Adjusted value (Make an adjustment according to steps <5> and <6>
in (3) in Subsec. 4.12.1.)
1980 (FS15i) Torque offset parameter

2087 (FS30i, 16i)
[Setting value] Adjusted value (If the center of an estimated disturbance value does
not become zero on an axis such as the gravity axis, make an
adjustment according to step <6> in (3) in Subsec. 4.12.1.)
<8> Adjusting the first stage acceleration

Specify the following parameters.
1860 (FS15i) First stage backlash acceleration amount (%)

2048 (FS30i, 16i)
[Unit of data] % (Backlash acceleration amount necessary to reverse the torque that
is equal to the friction torque in amount is assumed to be 100%.)
[Typical setting] 50 (Normally, optimum values range from 20% to 70%.)
To set a backlash acceleration amount of 0, -100 needs to be set.
Acceleration amount when the
direction of feed is reversed
Current friction torque 0
-100%
- 226 -
1987 (FS15i) First stage acceleration amount from negative direction to positive direction
2094 (FS30i, 16i) (%)
[Unit of data] %
Normally, this parameter is set to 0. If the quadrant protrusion varies
with the reverse direction of the position command in the machine
conditions, set an appropriate value in this parameter.
When this parameter is set, parameter No. 1860 (Series 15i) or No.
2048 (Series 30i, 16i, and so on) specifies the first stage
positive-to-negative backlash acceleration amount.
(Setting the first stage acceleration in the parameter window)
- 227 -
Before two-stage backlash acceleration

adjustment
(A delay in reverse motor rotation causes a
protrusion at each area of quadrant switching.)
First, set the value of [Typical setting]. Then, while viewing the
arc figure, adjust the first stage acceleration amount
parameter.(Make an adjustment at a low feedrate of about F500.)
First stage acceleration amount (adequate) First stage acceleration amount (too large)
(Protrusions caused by machine friction remain, (Cuts are caused by excessively high
but these protrusions are corrected later when acceleration at the time of reverse motor
second stage acceleration is adjusted.) rotation.)
Fig. 4.6.7 (b) Two-stage backlash acceleration (first stage acceleration amount adjustment)
1975 (FS15i) Second stage start position (detection unit)

2082 (FS30i, 16i)
[Typical setting] 10 (For a detection unit of 1 µm)
100 (For a detection unit of 0.1 µm)
NOTE
1 As the second stage start position, the absolute
value of the setting is used.
2 When setting = 0, the specification of 100 is
internally assumed.
- 228 -
1982 (FS15i) Second stage end scale factor

2089 (FS30i, 16i)
[Unit of data] In units of 0.1
[Valid data range] Other than Series 9096: 0 to 10279 (multiplication by 0 to 1027.9)
Series 9096: 0 to 642 (multiplication by 0 to 64.2)
[Typical setting] Normally, this value may be set to 0.
When the second stage end scale factor is set to 0, the second stage
acceleration distance is assumed as follows:
If a positive value is set as the second stage start position, a value
obtained by multiplying the start position by 2 is assumed.
If a negative value is set as the second stage start position, a value
obtained by multiplying the start position by 3 is assumed.
By setting the second stage end scale factor, the second stage
acceleration distance may be set to any value.
(Setting example)
When the second stage start position is set to 10, and the second
stage end scale factor is set to 50 (meaning multiplication by 5),
second stage acceleration is performed as shown below.
First stage Second stage acceleration amount

acceleration amount
10 50
Second stage acceleration distance=
Second stage start position × 5
Second stage start position Second stage end position

=Second stage start position
+Second stage acceleration distance
Fig. 4.6.7 (c) Second stage end scale factor
(Second stage acceleration setting in the parameter window)
- 229 -
Before start/end parameter adjustment
Set the following:

Start/end parameter = Value of [Typical setting]
Second stage acceleration amount = 500
Then, adjust the start/end parameter while viewing the timing of
second stage acceleration from the arc figure.
Start/end parameter (adequate) Start/end parameter (insufficient)

(A larger second stage acceleration amount is set (The time for second stage acceleration is too
to view the timing of second stage acceleration, so short, so that second stage protrusions are not
that cuts occur. This is corrected later.) fully eliminated.)
Fig. 4.6.7 (d) Two-stage backlash acceleration (adjustment of start position and end scale factor)
NOTE
Note that the two-stage backlash acceleration
cannot be used together with the backlash stop
function.
Second stage acceleration is not completed by nature until a distance

specified by "Second stage end scale factor" is moved. For example, if
only several microns are moved after the direction is reversed, second
stage acceleration continues. To prevent such continued acceleration
from occurring, set a maximum allowable duration of time with the
parameter below.
- 230 -
1769 (FS15i) Two-stage backlash acceleration end timer

2146 (FS30i, 16i)
[Unit of data] ms
<9> Second stage acceleration adjustment

The two-stage backlash acceleration function has effect even if
only first stage is used. However, a protrusion may linger
because of machine friction. In such a case second stage is
useful.
Adjust the second stage acceleration so that it falls in a range
where no cut occurs.
1724 (FS15i) Second stage acceleration amount for two-stage backlash acceleration
2039 (FS30i, 16i)
[Typical setting] 100 (Too large a value could cause a cut at low feedrate.)
NOTE
When second stage acceleration is not used, set
second stage acceleration amount = 0. The setting
of second stage start position = 0 alone cannot
disable second stage acceleration.
1790 (FS15i) Second stage offset for two-stage backlash acceleration

2167 (FS30i, 16i)
Normally, set 0.
Offset for the second stage acceleration amount. See Fig. 4.6.7 (a).
The second stage

acceleration amount is
adjusted to eliminate
protrusions and cuts.
Before second stage acceleration Second stage acceleration amount

amount adjustment (too large) (adequate)
Fig. 4.6.7 (e) Two-stage backlash acceleration (second stage acceleration amount adjustment)
- 231 -
<10>Second stage acceleration override adjustment

Second stage acceleration amounts can be overridden according
to the circular acceleration.
When using the second stage acceleration override function, set the
following.
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) OVR8
2018 (FS30i, 16i)
OVR8 (#2) 0: The format of the second stage acceleration override is in
reference to 4096.
1: The format of the second stage acceleration override is in
reference to 256.
Normally, set it to 1.
1725 (FS15i) Second stage acceleration override

2114 (FS30i, 16i)
When the second stage acceleration override function is used, the

second stage acceleration amount of two-stage backlash acceleration is
found from the following formula:
(Second stage acceleration amount)=
 (Second stage override setting) 
(Second stage acceleration amount setting) × 1 + α × 
 a 
If OVR8 = 1, a = 256
If OVR8 = 0, a = 4096
Here, let α be a circular acceleration, R be a radius (mm), F be a
circular feedrate (mm/min), and P be a detection unit (mm). Then, α
can be expressed as:
2
α = (F / 60 × 0.008)2  / P
R 
So, the second stage override setting and acceleration amount are
related as follows:
a  (Second stage acceleration amount) 
(Second stage override setting) = × − 1
α  (Second stage acceleration amount setting) 
Example)
When using a second stage acceleration amount override, adjust the
backlash second stage acceleration amount for two types of feedrates.
Suppose that the adjusted values below are obtained.
No. 1960#2 (Series 15i)=1, No. 2018#2 (Series 30i, 16i, and so on)=1
i) In the case of R10, F1000 (detection unit of 1 µm), the optimal
second stage acceleration amount is 40.
ii) In the case of R10, F6000 (detection unit of 1 µm), the optimal
second stage acceleration amount is 100.
From the results above, the expressions below are obtained.
For i)
2
α= (1000/60 × 0.008)2  0.001 = 3.56
10 
- 232 -
Expressions <1>
256  40 
3.56  (Second stage acceleration amount setting) 
For ii)
2
α= (6000/60 × 0.008)2  0.001 = 128
10 
Expressions <2>
256  100 
128  (Second stage acceleration amount setting) 
From expressions <1> and <2>, the following is obtained:
256  40 
× − 1
3.56  (Second stage acceleration amount setting) 
256  100 
= × − 1
128  (Second stage acceleration amount setting) 
Accordingly, (second stage acceleration amount setting) = 38.3 38

From expression <2> (or from expression <1>), (second stage
override setting) = 3.3 3
Set these values in No. 1724 and No. 1725 (Series 15i) or No. 2039
and No. 2114 (Series 30i, 16i, and so on). This completes the setting
of a second stage acceleration override.
NOTE
Second stage override is effective for second stage
offset.
<11>Setting a limit to the second stage acceleration amount

Making an optimum override setting for low-speed and
high-speed ranges may result in an insufficient acceleration
amount in a medium-speed range. To avoid this problem, adjust
overriding for low-speed and medium-speed ranges, and set an
optimum value for the high-speed range in the following
parameter as a limit value.
2751 (FS15i) Limit value for the two-stage backlash second stage acceleration amount
2338 (FS30i, 16i)
[Valid data range] 0 to 32767 (if this parameter is 0, no limit is placed to the second stage
acceleration amount.)
- 233 -
Second stage Second stage

Second stage
acceleration amount acceleration amount
acceleration amount
Limit value:
No.2338
Gradient:
No.2114
Intercept:
No.2039
Measurement Measurement Measurement Measurement Measurement Measurement

point A point B point C point A point B point C
If there is no sufficient acceleration amount at An optimum acceleration amount will be

measurement point B, there remains a quadrant protrusion. obtained at all measurement points.
Fig. 4.6.7 (f) Override adjustment for the second stage acceleration amount of two-stage backlash acceleration
<12>Direction-specific setting for second stage acceleration

If the optimum second stage acceleration amount varies
depending on the direction in which turn-over occurs, specify the
following parameters.
2752 (FS15i) Two-stage backlash second stage acceleration amount override for
turn-over from the negative direction to the positive direction
2339 (FS30i, 16i)
2753 (FS15i) Second stage acceleration amount override for turn-over from the negative
direction to the positive direction
2340 (FS30i, 16i)
Not used if the two-stage backlash second stage acceleration amount
from the negative direction to the positive direction (parameter No.
2752 (for the Series 15i) and No. 2339 (for the Series 30i, 16i, and so
on)) is 0.
This parameter takes effect when a reverse from the negative direction
to the positive direction takes place if the two-stage backlash second
stage acceleration amount from the negative direction to the positive
direction (parameter No. 2752 (for the Series 15i) and No. 2339 (for
the Series 30i, 16i, and so on)) is not 0.
It is not overridden if the setting is 0.
2754 (FS15i) Second stage acceleration limit value for turn-over from the negative
direction to the positive direction
2341 (FS30i, 16i)
Not used if the two-stage backlash second stage acceleration amount
from the negative direction to the positive direction (parameter No.
2752 (for the Series 15i) and No. 2339 (for the Series 30i, 16i, and so
on)) is 0. This parameter takes effect when a reverse from the negative
direction to the positive direction takes place if the two-stage backlash
second stage acceleration amount from the negative direction to the
positive direction (parameter No. 2752 (for the Series 15i) and No.
2339 (for the Series 30i, 16i, and so on)) is not 0.
If the setting is 0, the second stage acceleration amount is not limited.
- 234 -
[Parameters used for direction-based setting]

Series30i,16i, and so on
Direction-based Reverse Second stage Acceleration Acceleration
setting direction acceleration amount override limit value
None Common
No.2039 No.2114 No.2338
From + to -
Present
From - to+ No.2339 No.2340 No.2341
Series 15i
Direction-based Reverse Second stage Acceleration Acceleration
setting direction acceleration amount override limit value
None Common
No.1724 No.1725 No.2751
From + to -
Present
From - to+ No.2752 No.2753 No.2754
(Tip) Supplement on backlash compensation value setting

In an ordinary mode not using FAD (in a mode other than the advanced
preview modes indicated below), the backlash acceleration function is
enabled only when a positive backlash compensation value is set. In the
advanced preview modes indicated below, the backlash acceleration function
is enabled, regardless of the setting of a backlash compensation value.
When FAD is used, an ordinary mode is treated in the same way as the
advanced preview modes. So, the backlash acceleration function is enabled,
regardless of the setting of a backlash compensation value.
Ｇ code
Mode
Mode ON Mode OFF
Look-ahead acc./dec. mode before interpolation
AI nano contour control mode
G05.1Q1 G05.1Q0
High-precision contour control (⇒ Subsec.4.6.3)
AI high-precision contour control
G05P10000 G05P0
AI nano high-precision contour control
Fine HPCC
AI advanced preview control I mode
G05.1Q1 G5.1Q0
AI advanced preview control II mode
* With the Series-30i/31i/32i (servo software Series 90D0 and 90E0), advanced
preview feed-forward is applied, not based on G code, at all times.
* For the applicable CNCs, see Appendix D.
- 235 -
(4) Neglecting backlash acceleration during feeding by the handle

By enabling the bit below, the backlash acceleration function can be
enabled only during cutting feed.
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) BLCU
2009 (FS30i, 16i)
BLCU (#6) 1: To enable backlash acceleration only during cutting feed
NOTE
When bit 3 of No. 1800 is set to 1, the backlash
acceleration function is enabled at all times, and
switching is disabled.
With following series and editions of servo software, the bit 7 of
parameter No. 2752 (for the Series 15i) or bit 7 of No. 2339 (for the
Series 30i, 16i, and so on) can also be used to enable the backlash
acceleration function only during cutting feed.
- Series 90B0/C(03) and subsequent editions
- Series 90D0/A(01) and subsequent editions
- Series 90E0/A(01) and subsequent editions
By using this bit, switching is enabled even when bit 3 of No. 1800 is
set to 1. Backlash acceleration is enabled even at the hole bottom
during rigid tapping.
#7 #6 #5 #4 #3 #2 #1 #0
2611 (FS15i) BLCUT2
2223 (FS30i, 16i)
BLCUT2(#7) 1: The backlash acceleration function is enabled only during cutting
feed.
(5) Two-stage backlash acceleration function (type 2)

When the two-stage backlash acceleration function is used, quadrant
protrusions may be reduced more effectively by starting the second
stage acceleration as early as possible. The two-stage backlash
acceleration function type 2 enables the second stage acceleration
immediately after a reverse operation takes place.
- Series and editions of applicable servo software

90B0/W(23) and subsequent editions
90B1/A(01) and subsequent editions
- 236 -
- Comparison with the conventional second stage acceleration

Start of reverse operation
Conventional second stage
acceleration
First stage acceleration
Second stage acceleration
Second stage start position (set in the detection unit)

Second stage end position (set with a scale factor of start
distance)
The initial value is output until the second stage

Second stage acceleration attenuation start position is reached, and attenuation is
(type 2) performed in the area between the attenuation start
First stage acceleration position and end position.
Second stage acceleration
Second stage attenuation start position (set in the

detection unit)
Second stage end position (set in the detection unit)
Normally, second stage acceleration is not output until the second

stage start distance is reached. The two-stage backlash acceleration
type 2 starts outputting the acceleration amount immediately after the
reverse operation, and starts attenuation after the start distance.
- Setting parameters
#7 #6 #5 #4 #3 #2 #1 #0
2684(FS15i) 2NDTMG
2271(FS30i,16i)
2NDTMG(#5) 0: Does not use the two-stage acceleration type 2.
1: Uses the two-stage acceleration type 2.
1975(FS15i) Second stage attenuation start position

2082(FS30i,16i)
[Unit od data] Detection unit
[Typical setting] 0 to 10 µm
1982(FS15i) Second stage end position

2089(FS30i,16i)
[Unit od data] Detection unit
[Typical setting] 20 to 30 µm
NOTE
For the two-stage backlash acceleration function
type 2, the second stage end position is set directly
in the detection unit.
- 237 -
4.6.8 Static Friction Compensation Function
(1) Overview
When a machine, originally in the stop state, is activated, the increase
in speed may be delayed by there being a large amount of static
friction. The backlash acceleration function (see Subsec. 4.6.6 and
Subsec. 4.6.7) performs compensation when the motor rotation is
reversed. This function adds compensation data to a velocity
command when the motor, originally in the stop state, is requested to
rotate in the same direction, thus reducing the activation delay.

(3) Block diagram

Stop state Static friction
judgement operation compensation data
Move command + +
+ Velocity command
Position gain
− −
Velocity feedback
Position feedback

<1> Enable this function.
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) BLEN
2003 (FS30i, 16i)
BLEN (#5) 1: The backlash acceleration function is enabled.
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) SFCM
2005 (FS30i, 16i)
SFCM (#7) 1: The static friction compensation function is enabled.
- 238 -
<2> Set adjustment parameters.
1964 (FS15i) Time during which the static friction compensation function is enabled (in
2-ms units)
2071 (FS30i, 16i)
1965 (FS15i) Static friction compensation

2072 (FS30i, 16i)
Offset for the velocity command that is to be added at the start of
travel from a stopped state
1966 (FS15i) Stop state judgement parameter

2073 (FS30i, 16i)
[Method of setting] Stop determination time = (parameter setting) × Ts
Ts=8ms(Series 15i, 16i and so on), 4ms (Series 30i)
If the machine starts moving after stopping for the time set in this
parameter or more, this compensation function is enabled.
NOTE
1 If a small value is set in this parameter, feed at a
low feedrate is regarded by mistake as stop state,
and compensation may not be performed correctly.
In such a case, increase the setting of this
parameter.
2 When the static friction compensation function is
enabled, be sure to set a nonzero positive value in
this parameter.
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) BLST
2009 (FS30i, 16i)
BLST (#7) 1: The function used to release static friction compensation is
enabled.
1990 (FS15i) Parameter for stopping static friction compensation

2097 (FS30i, 16i)
Parameter related to the distance the tool travels until the end of the
static friction compensation function. Determine the setting by
looking at the actual shape.
- 239 -
- Static friction compensation (minus direction)

2347(FS30i)
Speed command offset applied when a movement is started from a
stop in the minus (-) direction.
When No. 2347≠0, direction-by-direction static friction compensation
is enabled. When a movement is made in the minus (-) direction, the
value set in parameter No. 2347 is applied as a static friction
compensation value. When a movement is made in the plus (+)
direction, the value set in parameter No. 2072 is applied.
When No. 2347=0, the value set in parameter No. 2072 is used as a
static friction compensation value.
Applied static friction

compensation
No.2347 Remarks
Movement in Movement in
+ direction − direction
Disables
0 No.2072 No. 2072 direction-by-direction static
friction compensation.
Enables
Non-zero
No.2072 No. 2347 direction-by-direction static
value
friction compensation.

- 240 -
4.6.9 Torsion Preview Control Function
(1) Overview
For relatively large machines having torsion, torsion occurs between
the motor and the machine end during acceleration and deceleration.
In machines of this type, positional deviation is caused by torsion
during acceleration and deceleration.
Torsion preview control compensates the speed command by
estimating the amount of torsion from the position command. This
reduces the amount of positional deviation during acceleration and
deceleration.
Compensation for
torsion delay
Coefficient depending on acceleration
Acceleration torsion
compensation
+ +
Σ PG Velocity
MCMD control TCMD
VCMD
－ Position Position
error gain
Position FB
Fig. 4.6.9(a) Torsion preview control structure

(Series 15i-B,16i-B,18i-B,21i-B)
(3) Notes
• This function works only in the nano interpolation mode.
• Because this function requires the user to observe the machine
operation at the time of adjustment, a separate detector is needed.
• Enable the feed-forward function.
• The function is more effective when the time constant of acc./dec.
is set so that acceleration changes smoothly. (Example:
Bell-shaped acc./dec. before interpolation plus linear-shaped
acc./dec. after interpolation)
- 241 -

<1> Setting feed-forward
Torsion preview control uses feed-forward processing. Therefore, the
following parameter must be set:
#7 #6 #5 #4 #3 #2 #1 #0
1883(FS15i) FEED
2005(FS30i,16i)
FEED(#1) The feed-forward function is:
0: Not used.
1: Used.
Set the parameter to use the feed-forward function. Since an error
amount is observed to determine the compensation value during the
adjustment, set 100% as the feed-forward coefficient for the feed for
which torsion preview control is used.
1985(FS15i) Advanced preview feed-forward coefficient (ADFF1)

2092(FS30i,16i)
1961(FS15i) Feed-forward coefficient (FALPH)

2068(FS30i,16i)
1767(FS15i) Position advanced preview feed-forward coefficient for cutting

2144(FS30i,16i)
When enabling torsion preview control also in rapid traverse, set FFR
to 1 to enable feed-forward control during rapid traverse.
#7 #6 #5 #4 #3 #2 #1 #0
1800(FS15i) FFR
1800(FS30i,16i)
FFR(#3) Feed-forward control during rapid traverse is:
0: Disabled.
1: Enabled.
- 242 -
<2> Operation measurement and time constant setting

To make adjustments, measure the velocity waveform and error
amount.
The waveform may be measured using either the waveform display
screen or SERVO GUIDE. When operating the machine at a feedrate
of about F10 m/min, check that the following waveform is observed:
Actual speed
F10m/min
Position error
500 pulses
=50µm
Fig. 4.6.9(b) Position error and actual speed
Torsion preview control differentiates position commands, so

attention should be given to the command mode and time constant
setting.
To ensure continuity of position command differential values, the
bell-shaped time constant and the time constant of acc./dec. after
interpolation must be set as well as the time constant of acc./dec.
before interpolation. The adjustment examples presented here assume
a large machine with a low resonance frequency of about 10 Hz and
set a time constant that prevents the machine from shaking largely at
the time of acc./dec.
Time constant of acc./dec. before interpolation
750 ms taken to reach F12000 mm/min
Acc./dec. before interpolation: bell-shaped time constant
200ms
Time constant of acc./dec. after interpolation
100ms
By setting the three time constants as explained above, the
acceleration component of position commands form a bell shape, and
the compensation value of torsion preview control also becomes
smooth. The values of the time constants depend on the vibration
status of the machine. So, set the time constants not to allow acc./dec.
to cause large vibration.
For position command data resolution and smoothness, nano

interpolation is used. When using torsion preview control, be sure to
perform operation in a nano interpolation mode such as AI nano
contour control or AI nano high precision contour control (when nano
interpolation is disabled, torsion preview control is also disabled.)
- 243 -
<3> Setting the acceleration

In torsion preview control, three acceleration areas can be specified,
and compensation coefficients can be set separately for these areas.
In a machine having the spring characteristic assumed by torsion
preview control, there are almost proportional relationships between
the acceleration and the torsion amount and position error. Therefore,
setting the acceleration set for the time constant of acc./dec. before
interpolation and one acceleration which is about 1/2 to 3/4 of the
acceleration is normally sufficient.
Compensation
value
Maximum K3
compensation K2
value K1: Compensation value for acceleration 1
K1 K2: Compensation value for acceleration 2
K3: Compensation value for acceleration 3
Acceleration Acceleration Acceleration Acceleration

1 2 3
Fig. 4.6.9(c) Acceleration dependent compensation curve
2796(FS15i) Torsion preview control: acceleration 1 (LSTAC1)

2383(FS30i,16i)

2384(FS30i,16i)

2385(FS30i,16i)
[Unit of data] D × 1000 [mm/s2] unit (D: detection unit (mm))

[Valid data raneg] 0 to 32767
• If the detection unit is 1 µm, the unit is 1 mm/s2; if the detection
unit is 0.1 µm, the unit is 0.1 mm/s2.
• If the acceleration is set to 0, the setting is ignored.
• Set acceleration values so that acceleration 1 is smaller than
acceleration 2, and acceleration 2 is smaller than acceleration 3.
If acceleration 1 is greater than acceleration 2, the setting of
acceleration 2 is ignored.
In this example, set the acceleration for the time constant of acc./dec.
before interpolation and another lower acceleration.
- LSTAC2
Time constant of acc./dec. before interpolation is 750ms taken to
reach F12000mm/min
→ Acceleration = 12000/60/0.75 = 266.7mm/s2
If the detection unit is 0.1 µm, a value is set in units of 0.1
mm/s2. Therefore,
LSTAC2 = 2667
- 244 -
- LSTAC1
Acceleration that is 3/4 of LSTAC2, 1000 ms taken to reach
F12000 mm/min
→ Acceleration = 12000/60/1 = 200 mm/s2, therefore,
LSTAC1 = 2000
- LSTAC3
LSTAC3 = 0 because LSTAC3 is not used.
Compensation value
Maximum
compensation value
K2
K1
Acceleration
LSTAC1 LSTAC2
=2000 =2667
Fig. 4.6.9(d) Example of compensation curve
<4> Setting the acceleration torsion compensation value

The acceleration torsion compensation value is used to compensate the
amount of torsion generated at a constant acceleration. While
changing the acceleration setting, measure the position error generated
at a constant acceleration.
Actual speed
100
90
100 pulses
Position error
=10µm
Fig. 4.6.9(e) Position error at LSTAC2
- 245 -
Actual speed
60
45
100 pulses Position

=10µm error
Fig. 4.6.9(f) Position error at LSTAC1
Set the values measured in Fig. 4.6.9 (e) and Fig. 4.6.9 (f) above in the
acceleration torsion compensation values shown below.
(Acceleration torsion amount)

2799(FS15i) Torsion preview control: Acceleration torsion compensation value K1
(LSTK1)
2386(FS30i,16i)
Set the torsion amount generated at acceleration 1 in the detection unit.
When 0 is set, compensation is disabled.

(LSTK2)
2387(FS30i,16i)
Set the torsion amount generated at acceleration 2 in the detection
unit.
When 0 is set, acceleration 1 and the K1 setting are applied. (See Fig.
4.6.9(g).)

(LSTK3)
2388(FS30i,16i)
Set the torsion amount generated at acceleration 3 in the detection
unit.
When 0 is set, acceleration 2 and the K2 setting are applied. (See Fig.
4.6.9(h).)
The compensation values are corrected automatically so that the
following is satisfied: K1 ≤ K2 ≤ K3. (See Fig. 4.6.9(i).)
- 246 -
Compensation value Compensation value

Maximum compensation Maximum compensation
value value
K3
K2
K1 K1
K2 K3
Acceleration 1 Acceleration 2 Acceleration 3 Acceleration 1Acceleration 2 Acceleration 3
Fig. 4.6.9(g) Compensation curve when K2 = 0 Fig. 4.6.9(h) Compensation curve when K3 = 0
Compensation Setting value Compensation Corrected value

value value
K3 K3
K1 K1 K2
K2
Acceleration 1 Acceleration 2 Acceleration 3 Acceleration 1 Acceleration 2 Acceleration 3

Fig. 4.6.9(i) Automatic compensation of the compensation curve
(Acceleration torsion amount for each direction)

2804(FS15i) Torsion preview control: Acceleration torsion compensation value K1N (LSTK1N)
2391(FS30i,16i)
Set the amount of torsion generated at acceleration 1 (when the
acceleration is a negative value) in the detection unit.
2392(FS30i,16i)
acceleration is a negative value) in the detection unit.
2393(FS30i,16i)
acceleration is a negative value) in the detection unit. If 4 is set,
acceleration 2 and the settings up to K2 apply.
CAUTION
When all the three accelerations are not used, set 0
in the parameter of the acceleration not used.
- 247 -
From Fig. 4.6.9 (e) and Fig. 4.6.9 (f), LSTK1 through LSTK3 and
LSTK1N through LSTK3N are set as follows:
LSTK1=60, LSTK2=100, LSTK3=0
LSTK1N=45, LSTK2N=90, LSTK3N=0
<5> Setting the maximum compensation value (enabling torsion preview control)
2795(FS15i) Torsion preview control: Maximum compensation value (LSTCM)

2382(FS30i,16i)
Set the maximum value of the compensation value to be added to the
velocity command in the detection unit. By setting the parameter to a
value greater than 0, torsion preview control is enabled. Set a value
greater than the maximum position error value measured (a value
obtained by multiplication by about 1.2 to 2).
LSTCM=500
The above setting enables this compensation, which reduces the
position error generated at the time of acc./dec.
Actual speed Actual speed
Position error Position error

500 pulses 500 pulses
=50µm =50µm
Fig. 4.6.9(j) Effect of acceleration torsion compensation
<6> Setting the torsion delay compensation value

Just with the acceleration torsion compensation value, the torsion
amount generated at the start of acc./dec. due to delay in velocity
control cannot be corrected, therefore there is a position error still left.
Adjust the torsion delay compensation value while observing the
waveform plotted at the time of acc./dec.
2802(FS15i) Torsion preview control: Torsion delay compensation value KD (LSTKD)

2389(FS30i,16i)
2809(FS15i) Torsion preview control: Torsion delay compensation value KDN (LSTKDN)
2396(FS30i,16i)
LSTKDN is used when there is a difference in delay between the start

of acceleration and the start of deceleration.
- 248 -
Compensation for
torsion delay
compensation
+ +
Σ PG Velocity
MCMD control TCMD
VCMD
－ Position Position
error gain
Position FB
Fig. 4.6.9(k) Compensation for torsion delay
Actual speed Actual speed
Positional error Positional error

500 pulses 500 pulses
=50µm =50µm
Fig. 4.6.9(l) Effect of compensation for torsion delay - 1
When the torsion delay compensation value is set to 2000, there is

slight position error still left, so a fine adjustment is made. Then, the
position error is decreased to 10 µm or less as shown in the figure
below.
(Torsion delay compensation value =3000 / 2500)
Actual speed
KD=3000
KD=2500
Position error
500 pulses
=50µm
Fig. 4.6.9(m) Effect of compensation for torsion delay - 2
- 249 -
<7> Setting the torsion torque compensation coefficient

Torsion torque compensation is set when an adequate velocity loop
gain cannot be obtained and acceleration torsion compensation does
not work efficiently. The delay in velocity control can be compensated
by adding the differential of the compensation value to TCMD.
2815(FS15i) Torsion preview control: Torsion torque compensation coefficient LSTKT

2402(FS30i,16i)
[Unit of data] %
Compensation coefficient used when the compensation value of
VCMD is differentiated to compensate TCMD. When 100% is set as
the compensation coefficient for TCMD, the acceleration amount of
the motor itself is indicated.
Torsion torque compensation

Differential LSTKT
compensation
+ +
Σ PG Velocity control
MCMD VCMD TCMD
- Position error Position
gain
Position FB
Fig. 4.6.9(n) Torsion torque compensation
- 250 -
4.7 OVERSHOOT COMPENSATION FUNCTION

#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) OVSC
2003 (FS30i, 16i)
OVSC (#6) 1: To enable the overshoot compensation function
1857 (FS15i) Velocity loop incomplete integral gain (PK3V)

2045 (FS30i, 16i)
* Basically, reset the parameter to 0 if you do not use the overshoot
compensation function.
1970 (FS15i) Overshoot compensation counter (OSCTP)

2077 (FS30i, 16i)

(3) Explanation
(a) Servo system configuration
Fig. 4.7 (a) shows the servo system configuration. Fig. 4.7 (b)
shows the velocity loop configuration.
+
NC Kp Velocity loop 1/s
MCMD − VCMD
Position feedback Kp: Position gain
Fig. 4.7 (a) Digital servo system configuration

+ + TCMD
PK1V/s Kt/ (Jm • s)
VCMD − −
Motor
PK2V
Velocity feedback PK1V: Velocity loop integral gain

PK2V: Velocity loop proportional gain
/s: Integrator
Fig. 4.7 (b) Velocity loop configuration
- 251 -
(b) When incomplete integration and overshoot compensation are not used.
First, 1–pulse motion command is issued from NC. Initially, because
the Position Feedback and Velocity Feedback are “0”, the 1–pulse
multiplied position gain Kp value is generated as the velocity
command (VCMD).
Because the motor will not move immediately due to internal friction
and other factors, the value of the integrator is accumulated according
to the VCMD. When the value of this integrator creates a torque
command, large enough to overcome the friction in the machine
system, the motor will move and VCMD will become “0” as the value
of MCMD and the Position Feedback becomes equal.
Furthermore, the Velocity Feedback becomes “1” only when it is
moved, and afterwards becomes “0”. Therefore the torque command is
held fixed at that determined by the integrator.
The above situation is shown in Fig. 4.7 (c).
t0 t1
Move command 1
(MCMD)
1
Position Feedback
Speed command Kp
(VCMD)
Velocity Feedback
PK1V × 1 pulse
Integrator
TCMD1
Friction in the
PK1V × 1 pulse
machine system TCMD2
Torque command
PK1V × 2 pulses
(TCMD)
Fig. 4.7 (c) Response to 1 pulse movement commands
If Fig. 4.7 (c) on the previous page, the torque (TCMD1) when
movement has started becomes greater than the machine static friction
level. The motor will move 1 pulse, and finally stops at the TCMD2
level.
Because the moving frictional power of the machine is smaller than
the maximum rest frictional power, if the final torque TCMD2 in Fig.
4.7 (c) is smaller than the moving friction level, the motor will stop at
the place where it has moved 1 pulse, Fig. 4.7 (d). When the TCMD2
is greater than the moving friction level the motor cannot stop and
overshoot will occur Fig. 4.7 (e).
The overshoot compensation function is a function to prevent the
occurrence of this phenomenon.
- 252 -
(c) Response to 1 pulse movement commands

(i) Torque commands for standard settings (when there is no
overshoot)
Torque command (TCMD)
TCMD1
Static friction
PK1V × 1 pulse
Dynamic friction
TCMD2
PK2V × 1 pulse
Time
Fig. 4.7 (d) Torque commands (when there is no overshoot)
(ii) Torque commands for standard settings (during overshoot)

Torque command
(TCMD) TCMD1
Static friction PK1V × 1 pulse
TCMD2
Dynamic friction PK2V × 1 pulse
Time
Fig. 4.7 (e) Torque commands (during overshoot)
Conditions to prevent further overshoot are as follows.

When
TCMD1 > static friction > dynamic friction > TCMD2…… <1>
and there is a relationship there to
TCMD1 > static friction > TCMD2 > dynamic friction…… <2>
regarding static and dynamic friction like that of (ii), use the
overshoot compensation in order to make <2> into <1>.
The torque command status at that time is shown in (iii).
(iii) Torque command when overshoot compensation is used

Function bit
OVSC = 1 (Overshoot compensation is valid)
Parameter
PK3V: around 30000 to 25000 (Incomplete integral coefficient)
(Example)
when PK3V=32000 time constant approx. 42 msec
TCMD1
Static friction
This time constant

is fixed at the
Dynamic friction PK3V value.
TCMD2
Time
Fig. 4.7 (f) Torque command (when overshoot is used)
- 253 -
If this overshoot compensation function is used, it is possible to

prevent overshoot so that the relationship between machine static
and dynamic friction and TCMD2 satisfies <1>, however the
torque TCMD during machine stop is
TCMD2 = 0
the servo rigidity during machine stop is insufficient and it is
possible that there will be some unsteadiness at ±1 pulse during
machine stop.
There is an additional function to prevent this unsteadiness in the
improved type overshoot prevention function and the status of
the torque command at that time is shown in (iv).
(iv) Torque command when the improved type overshoot

compensation is used
Function bit
OVSC = 1 (Overshoot compensation is valid)
Parameter
PK3V: around 32000 (Incomplete integral coefficient)
OSCTP: around 20 (Number of incomplete integral)
When overshooting with this parameter, try increasing the value of the
overshoot protection counter (OSCTP) by 10. Conversely, when there
is no overshooting, but unsteadiness occurs easily during machine stop,
decrease the overshoot protection counter (OSCTP) value by 10.
When overshoot protection counter (OSCTP) = 0 it is the same as
existing overshoot compensation.
TCMD1
Static friction
This time constant
is fixed at the
Dynamic friction PK3V value.
t3 TCMD3
TCMD2
Time
Fig. 4.7 (g) Torque command (using improved type overshoot

compensation)
If this function is used, the final torque command is TCMD3. If the

parameter PK3V (t3) is fixed so that this value becomes less than the
dynamic friction level, overshoot is nullified. Because torque
command is maintained to some degree during machine stop, it is
possible to decrease unsteadiness during machine stop.
- 254 -
(4) Improving overshoot compensation for machines using a 0.1-µm

detection unit
(a) Overview
Conventional overshoot compensation performs imperfect integration
only when the error is 0.
A machine using a 0.1-µm detection unit, however, has a very short
period in which the error is 0, resulting in a very short time for
imperfect integration.
The new function judges whether to execute overshoot compensation
when the error is within a predetermined range.
(b) Setting parameters

1994 (FS15i) Overshoot compensation enable level
2101 (FS30i, 16i)
[Recommended value] 1 (detection unit: 1 µm)
10 (detection unit: 0.1 µm)
To set an error range for which overshoot compensation is enabled, set
∆, as indicated below, as the overshoot compensation enable level.
Error
Imperfect integration disabled
Error = + ∆
Imperfect
Error = 0
integration enabled
Error = − ∆
Imperfect integration disabled
Fig. 4.7 (h) Relationship between error and overshoot compensation
(5) Overshoot compensation type 2

(a) Overview
For a machine using, for example, 0.1-µm detection units, the use of
the conventional overshoot compensation function may generate
minute vibrations when the machine stops, even if the parameter for
the number of incomplete integration is set.
This is caused by the repeated occurrence of the following
phenomena:
• While the machine is in the stopped state, the position error falls
within the compensation valid level, and the integrator is
rewritten. Subsequently, the motor is pushed back by a machine
element such as a machine spring element, causing the position
error to exceed the compensation valid level.
• While the position error is beyond the threshold, a torque
command is output to decrease the position error, then it
decreases to below the threshold again.
In such a case, set the bit indicated below to suppress the minute
vibration.
- 255 -

#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) OVS1
2202 (FS30i, 16i)
OVS1 (#3) 1: Overshoot compensation is enabled only once after the
termination of a move command.
Overshoot compensation (Conventional type: When OVS1 = 0)

Very small vibration occurs because incomplete integration and
complete integration are repeated.
Position
error
Valid
compensation
level
Time
Compensation Compensation Compensation

enabled (incomplete enabled (incomplete enabled (incomplete
integration) integration) integration)
Overshoot compensation (Type 2: When OVS1 = 1)

Very small vibration can be suppressed because incomplete
integration is performed only once after move command completion.
Position
error
Valid
compensation
level
Time
Compensation Compensation
enabled (incomplete disabled (complete
integration) integration)
Fig. 4.7 (i) Overshoot compensation type 2
- 256 -
4.8 HIGH-SPEED POSITIONING FUNCTION
High-speed positioning is used in the following cases:

<1> To perform point-to-point movement quickly, where the
composite track of two or more simultaneous axes can be ignored
such as, for example, in a punch press
<2> To speed up positioning in rapid traverse while errors in the
shape during cutting must be minimized (reduction of cycle time)
In case <1>, the position gain switching function and the low-speed
integral function are effective (⇒ See Subsec. 3.3.2, "High-Speed
Positioning Adjustment Procedure"). For the application of <2> above,
a combination of the fine acc./dec. (FAD) function and rapid traverse
feed-forward is useful. In the Series 30i, 31i, and 32i, nano
interpolation is always enabled, so the fine acc./dec. function is
unnecessary (unusable). For the use in <2> above, only the setting of
the feed-forward function is required.
This section explains these functions.
4.8.1 Position Gain Switching Function
(1) General
An increase in the position gain is an effective means of reducing the
positioning time when the machine is about to stop.
An excessively high position gain decreases the tracking ability of the
velocity loop, making the position loop unstable. This results in
hunting or overshoot. A position gain adjusted in high-speed response
mode produces a margin in the position gain when the machine is
about to stop.
Increase the position gain in low-speed mode so that both the
characteristics in high-speed response mode and a short positioning
time are achieved.
NOTE
When this function is used, the error amount in
constant-speed feed and the actual position gain
indication on the CNC do not match the logical values.
(2) Series and edition of applicable servo software

- 257 -

<1> This parameter specifies whether to enable the position gain
switching function as follows:
#7 #6 #5 #4 #3 #2 #1 #0
1957 (FS15i) PGTW
2015 (FS30i, 16i)
PGTW (#0) The position gain switching function is used.
0: Invalid
1: Valid
<2> This parameter specifies whether to set the velocity at which

position gain switching is to occur, as follows:
1713 (FS15i) Limit speed for enabling position gain switching
2028 (FS30i, 16i)
The position gain is doubled with a speed lower than or equal to the
speed specified above.
[Unit of data] Rotary motor: 0.01 min-1
Linear motor: 0.01 mm/min
REFERENCE
Using the high-speed positioning velocity increment
system magnification function (→ (5) in Subsec.
4.8.1) can increase the effective velocity to ten
times.
Fig. 4.8.1 (a) shows the relationships between the position error and
velocity command.
(4) When the feed-forward function is used at the same time (position gain
switching function type 2)
When using the position gain switching function together with the
feed-forward function, make the setting below.
(a) Overview
When the conventional position gain switching function is used in
conjunction with the feed-forward function, it can cause an overshoot
at a relative low feed-forward coefficient, sometimes resulting in a
difficulty in adjustment, because also the feed-forward term-based
effect is doubled. Position gain switch function type 2 has been
improved to make position gain switching independently of the
feed-forward function.
- 258 -

In addition to the parameter of the position gain switching function
described earlier, set the following parameter.
#7 #6 #5 #4 #3 #2 #1 #0
1744 (FS15i) PGTWN2
2204 (FS30i, 16i)
PGTWN2 (#5) Specifies whether to double the feed-forward-based effect at position
gain switching as follows:
0: To double
1: Not to double
NOTE
This function is invalid when the VCMD interface is
in use.
(When the VCMD interface is in use, set PGTWN2
= 0.)
(5) High-speed positioning velocity increment system magnification function

(a) Overview
This function increases the velocity increment system for the effective
velocity parameter of the high-speed positioning functions (position
gain switch and low-speed integral functions) to ten times.

Using the following parameter can change the increment system for
the effective velocity.
#7 #6 #5 #4 #3 #2 #1 #0
1744 (FS15i) HSTP10
2204 (FS30i, 16i)
HSTP10 (#1) Specifies the effective velocity increment system for the high-speed
positioning functions (position gain switch and low-speed integral
functions) as follows:
0: 0.01 min-1 (rotary motor), 0.01 mm/min (linear motor)
1: 0.1 min-1 (rotary motor), 0.1 mm/min (linear motor)
NOTE
The value set in this function applies to the
increment system of both the "position gain
switching function" and "low-speed integral
function."
- 259 -
Velocity command
When enabled
When disabled
Positional deviation
Position gain
Doubled area
Fig. 4.8.1 (a) Position gain switching
- 260 -
4.8.2 Low-speed Integral Function
(1) Overview
To ensure that the motor responds quickly, a small time constant must
be set so that a command enabling quick startup is issued.
If the time constant is too small, vibration or hunting occurs because
of the delayed response of the velocity loop integrator, preventing
further reduction of the time constant.
With the low-speed integral function, velocity loop integrator
calculation is performed in low-speed mode only. This function
ensures quick response and high stability while maintaining the
positioning characteristics in the low-speed and stop states.
(2) Series and edition of applicable servo software


<1> Specify whether to enable the low-speed integral function.
#7 #6 #5 #4 #3 #2 #1 #0
1957 (FS15i) SSG1
2015 (FS30i, 16i)
SSG1 The low-speed integral function is used.
0: Invalid
1: Valid
<2> Specify whether to enable integration at acc./dec. time.
1714 (FS15i) Limit speed for disabling low-speed integral at acceleration

2029 (FS30i, 16i)
The integral gain is invalidated during acceleration at a speed higher
than or equal to the specified speed.
- 261 -
1715 (FS15i) Limit speed for enabling low-speed integral at deceleration

2030 (FS30i, 16i)
The integral gain is validated during deceleration at a speed lower
than or equal to the specified speed.
REFERENCE
Using the high-speed positioning velocity increment
system magnification function (→ (5) in Subsec.
4.8.1) can increase the effective velocity to ten
times.
This function can specify whether to enable the velocity loop

integration term for two velocity values, the first for acceleration and
the second for deceleration. It works as shown in Fig. 4.8.2 (a).
Valid velocity
at deceleration
Invalid velocity
at acceleration
Time
Integration
disabled
Fig. 4.8.2 (a) Integration invalid range at low-speed integral
- 262 -
4.8.3 Fine Acceleration/Deceleration (FAD) Function
(1) Overview
The fine acceleration/deceleration (fine acc./dec.) function enables
smooth acc./dec. This is done by using servo software to perform
acc./dec. processing, which previously has been performed by the
CNC. With this function, the mechanical stress and strain resulting
from acc./dec. can be reduced.
(2) Features
• Acc./dec. is controlled by servo software at short intervals,
allowing smooth acc./dec.
• Smooth acc./dec. can reduce the stress and strain applied to the
machine.
• Because of the reduced stress and strain on the machine, a shorter
time constant can be set (within the motor acceleration capability
range).
• Two acc./dec. command types are supported: bell-shaped and
linear acc./dec. types.
• An application of the fine acc./dec. function is found in the
cutting and rapid traverse operations; for each operation, the
FAD time constant, feed-forward coefficient, and velocity
feed-forward coefficient can be used separately.

NOTE
In the Series 30i, 31i, and 32i, smooth acc./dec. is
always performed by nano interpolation, so the fine
acc./dec. function is unnecessary. (The settings for
the function are also ignored.)
(4) Setting basic parameters

#7 #6 #5 #4 #3 #2 #1 #0
1951 (FS15i) FAD
2007 (FS16i)
FAD (#6) 1: Enables the fine acc./dec. function.
NOTE
When this parameter is set, the power must be
- 263 -
#7 #6 #5 #4 #3 #2 #1 #0
1749 (FS15i) FADL
2209 (FS16i)
FADL (#2) 0: FAD bell-shaped
1: FAD linear type
* Set 1 (linear type) usually .
NOTE
1702 (FS15i) Fine acc./dec. time constant (ms)

2109 (FS16i)
[Valid data range] 8 to 64 (Standard setting: 24)
A value exceeding the valid data range is clamped to the upper or
lower limit of the range.
When the fine acc./dec. and feed-forward functions are used together,
set the coefficient in the following parameter.
(The parameter No. is the same as that used for advanced preview
control.)
1985 (FS15i) Position feed-forward coefficient (in units of 0.01%)

2092 (FS16i)
NOTE
1 Feed-forward control is enabled by setting bit 1 of
No. 1883 (Series 15i) or No. 2005 (Series 16i and
so on) to 1.
2 The velocity feed-forward coefficient is set in
parameter No. 1962 (Series 15i) or No. 2069
(Series 16i and so on) which is the same
parameter as that used for normal operation.
3 Generally, the fine acc./dec. function is enabled in
cutting mode only.
4 If bit 3 of No. 1800 is set to 1, the FAD function is
enabled both for cutting and rapid traverse mode.
(5) Setting parameters for the fine acc./dec. function, used separately for
cutting and rapid traverse
As mentioned above, set the fine acc./dec. function bit and the bit for
selecting the bell-shaped or linear type.
Then, set the following:
#7 #6 #5 #4 #3 #2 #1 #0
1800 (FS15i) FFR
1800 (FS16i)
FFR (#3) 1: Enables feed-forward in rapid traverse also.
- 264 -
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) FADCH
2202 (FS16i)
FADCH (#0) 1: Enables the fine acc./dec. function, used separately for cutting
and rapid traverse.
NOTE
When this parameter is set, the power must be turned off
before operation is continued.
In cutting mode, the following parameters are used:
1766 (FS15i) Fine acc./dec. time constant 2 (ms)

2143 (FS16i)
A value that falls outside this range, if specified, is clamped to the
upper or lower limit.
1767 (FS15i) Position feed-forward coefficient for cutting (in units of 0.01%)
2144 (FS16i)
1768 (FS15i) Velocity feed-forward coefficient for cutting (%)

2145 (FS16i)
In rapid traverse mode, the following parameters are used:
1702 (FS15i) Fine acc./dec. time constant (ms)

2109 (FS16i)
A value that falls outside this range, if specified, is clamped to the
upper or lower limit.
1985 (FS15i) Position feed-forward coefficient for rapid traverse (in units of 0.01%)
2092 (FS16i)
1962 (FS15i) Velocity feed-forward coefficient for rapid traverse (%)

2069 (FS16i)
NOTE
1 When the settings above are made, both of the fine acc./dec.
time constant and feed-forward coefficient can be automatically
switched for cutting feed or rapid traverse. To switch the
feed-forward coefficient only, use the cutting feed/rapid
traverse switchable feed-forward function. (See Subsec. 4.6.4.)
2 When FAD, used separately for cutting and rapid traverse, is
applied to axes under simple synchronous control, set the
function bit for both the master and slave axes. When the
function is enabled for the master axis only, switching between
cutting and rapid traverse modes cannot be performed.
- 265 -
Table 4.8.3 Feed-forward coefficient and fine acc./dec. time constant parameters classified by use
Series 16i, 18i, 21i, 0i
Parameters for rapid
Parameter setting Parameters for cutting
traverse
Position Velocity Position Velocity
No.2005 No.2007 No.1800 No.2202 FAD time FAD time
FF FF FF FF
#1 #6 #3 #0 constant constant
coefficient coefficient coefficient coefficient
No. 2068
Cutting FF 1 0 0 0
No. 2092
No. 2069 - - - -
Usual FF
No. 2068 No. 2068
(cutting FF 1 0 1 0
No. 2092
No. 2069 -
No. 2092
No. 2069 -
+ rapid traverse FF)
Cutting FAD 0 1 0 0 - - No. 2109 - - -
Cutting/rapid
0 1 1 1 - - No. 2143 - - No. 2109
traverse-specific FAD
Cutting FAD + cutting FF 1 1 0 0 No. 2092 No. 2069 No. 2109 - - -
Cutting FAD + usual FF 1 1 1 0 No. 2092 No. 2069 No. 2109 No. 2092 No. 2069 -
Cutting/rapid
traverse-specific FAD +
1 1 1 1 No. 2144 No. 2145 No. 2143 No. 2092 No. 2069 No. 2109
cutting/rapid traverse-specific
FF
Series 15i
Parameters for rapid
Parameter setting Parameters for cutting
traverse
Position Velocity Position Velocity
No.1883 No.1951 No.1800 No.1742 FAD time FAD time
FF FF FF FF
#1 #6 #3 #0 constant constant
coefficient coefficient coefficient coefficient
No. 1961
Cutting FF 1 0 0 0
No. 1985
No. 1962 - - - -
No. 1961 No. 1961
Usual FF 1 0 1 0
No. 1985
No. 1962 -
No. 1985
No. 1962 -
Cutting FAD 0 1 0 0 - - No. 1702 - - -
Cutting/rapid traverse-specific
0 1 1 1 - - No. 1766 - - No. 1702
FAD
Cutting FAD + cutting FF 1 1 0 0 No. 1985 No. 1962 No. 1702 - - -
Cutting FAD + usual FF 1 1 1 0 No. 1985 No. 1962 No. 1702 No. 1985 No. 1962 -
Cutting/rapid traverse-specific
FAD + cutting/rapid 1 1 1 1 No. 1767 No. 1768 No. 1766 No. 1985 No. 1962 No. 1702
traverse-specific FF
NOTE
1 In the above tables, the abbreviations "FF" and
"FAD" refer to the feed-forward function and fine
acc./dec. function, respectively.
2 Of two parameter numbers stacked one on the
other in each field of the above tables, the upper
one is used in non-advance mode, and the lower
one, in advance mode.
- 266 -
(6) Cautions for combined use of the synchronization function with the
spindle axis and fine acc./dec.
The restrictions listed below are imposed on the combined use of the
synchronization function between the servo axis and spindle axis and
the fine acc./dec. function.
(Disable the fine acc./dec. function if the combine use is impossible.)
Use of FAD for servo axis

Function When FAD is When FAD is Cautions for combined use
disabled for enabled for
spindle axis spindle axis
When FAD is disabled for spindle axis :
During rigid tapping, FAD and feed-forward control are
disabled. For synchronization, the position gain for the
servo axis must be changed. See (7).
Rigid tapping Allowed Allowed
When FAD is enabled for spindle axis :
The same FAD time constant, acc./dec. type, feed-forward
coefficient, and position gain must be used for the servo
axis (during cutting) and the spindle axis.
Advanced The same FAD time constant, acc./dec. type, feed-forward
preview control Not allowed Allowed coefficient, and position gain must be used for the servo axis
rigid tapping (during cutting) and the spindle axis.
Cs axis contour
Not allowed Allowed coefficient, and position gain must be used for the servo axis
control
(during cutting) and the spindle axis.
Hob function Not allowed Not allowed Disable the fine acc./dec. function.
EGB function Not allowed Not allowed Disable the fine acc./dec. function.
Flexible
Not allowed Allowed coefficient, and position gain must be used for the servo axis
synchronization
(during cutting) and the spindle axis.
NOTE
The spindle FAD function can be used when an αi spindle amplifier and FANUC
Series 16i/18i/21i MODEL B CNC are used.
Spindle software : Series 9D50/E(05) and subsequent editions
CNC software : M series : Series B0H1/M(13) and subsequent editions,
Series BDH1M(13) and subsequent editions,
Series DDH1/M(13) and subsequent editions,
Series BDH5/C(03) and subsequent editions
T series : Series B1H1/M(13) and subsequent editions
Series BEH1/M(13) and subsequent editions
Series DEH1/M(13) and subsequent editions
For details of the spindle FAD function, refer to "FANUC AC SPINDLE MOTOR αi
series, FANUC AC SPINDLE MOTOR βi series, FANUC AC BUILT-IN SPINDLE
MOTOR Bi series Parameter Manual (B-65280EN)".
Combined
Function use with FAD Cautions for combined use
function
Flexible synchronization For the axes to be synchronized with each other, the same FAD time
Allowed
(between servo axes) constant, feed-forward coefficient, and position gain must be set.
- 267 -
(7) Rigid tapping synchronization when spindle axis FAD is disabled

(a) Overview
Because using fine acc./dec. causes the servo axis delay (error) to
increase by 1 ms, rigid tapping with fine acc./dec. set up results in an
increase of synchronization error against the spindle. To avoid this
increase, use the following procedure to change the servo axis position
gain for rigid tapping.
NOTE
In advanced preview control mode, rigid tapping
cannot be used together with fine acc./dec. In this
case, disable fine acc./dec.
(b) Setup procedure

By setting the parameter below, the position gain can be automatically
changed only for the servo axis to establish synchronization.
(Parameter)
#7 #6 #5 #4 #3 #2 #1 #0
1749 (FS15i) FADPGC
2209 (FS16i)
FADPGC (#3) Specifies whether to perform synchronization in rigid tapping mode
when FAD is set up, as follows:
0: Not to perform
1: To perform ← To be set
NOTE
2 If this parameter is set, the servo position gain
increases by 1 ms even when rigid tapping is not
used.
3 It is necessary to set this parameter for all axes
that are subjected to contouring.
- 268 -
(Reference)
With Series 16i and so on, two types of parameters are available
for position gain setting. By setting the parameters as described
below, a position gain match can be ensured between the servo
axis and spindle.
NOTE
Do not make following setting when FADPGC = 1
is set.
a. Nos. 4065 to 4068: Spindle servo mode position gain

b. Nos. 5280 to 5284: Rigid tapping position loop gain
Parameter type "a" corresponds to the spindle position loop gain
for rigid tapping, and parameter type b, to the servo axis position
loop gain. Usually, both parameter types take the same values.
For a servo axis with fine acc./dec. specified, however, set
parameter type b with the values obtained using the following
calculation:
Newly set 100000 Usually set

position gain = × position gain
value 100000 - Usually set position value
gain value
Example of parameter setting)

Position gain (1/s) Usually set value Newly set value
15 1500 1523
16.66 1666 1694
20 2000 2041
25 2500 2564
30 3000 3093
33.33 3333 3448
35 2500 3627
40 4000 4167
45 4500 4712
50 5000 5263
- 269 -
(8) Other specifications to note regarding the fine acc./dec. function

• Advanced preview control and fine acc./dec. can be used
together. (The time constants before and after advanced preview
interpolation, and the fine acc./dec. time constant are effective.)
• If FAD is set, then the G05 P10000 command is issued with
HPCC, FAD is disabled.
• Using the FAD function increases the position error as follows:
- For FAD bell-shaped
Deviation incerase (pulses) =
Feedrate (mm/min)  FAD time constant (ms) 
× + 1
60 × 1000 × Detection unit (mm)  2 
- For FAD linear type
Feedrate (mm/min)  FAD time constant (ms) + 1 
× + 1
60 × 1000 × Detection unit (mm)  2 
Example)
When feed operation is performed using F1800 with a position
gain of 30 (1/s) and a detection unit of 0.001 mm, the position
error is normally expressed as follows:
Normal deviation (pulses) =
Feedrate (mm/min)
60 × Position gain (1/s) × Detection unit (mm)
1800
= = 1000( pulses )
60 × 30 × 0.001
When the FAD function (FAD bell-shaped) is used with the time
constant set to 64 ms, the deviation increases as follows:
1800  64 
× + 1 = 990( pulses )
60 × 1000 × 0.01  2 
When FAD is used, the entire deviation is then obtained as
follows:
Deviation when FAD is used (pulses) = 1000 + 990
= 1990 (pulses)
The combined use of the FAD function and the feed-forward function
does not increase the position error so much as expected, because the
feed-forward function decreases a delay against the command. When
the FAD function is used alone, however, a higher error
overestimation level must be set, considering the increase in the
deviation.
- 270 -
(9) Examples of applying the fine acc./dec. function
Motor velocity
Motor velocity
Torque command Torque command
Conventional control in which the When the feed-forward function is used

feed-forward function is not used
Motor velocity
Motor velocity
Torque command
Torque command
When the feed-forward and rapid traverse When the feed-forward and fine acceleration/
bell-shaped acc./dec. deceleration functions are used
(Acc./dec. by the CNC)
functions are used
- 271 -
4.9 SERIAL FEEDBACK DUMMY FUNCTIONS
4.9.1 Serial Feedback Dummy Functions
(1) Overview
The serial feedback dummy functions ignore servo alarms of
non-servo axes.

Series 9096 does not support the settings of such dummy axes.
(This series is not planed to support this function in the future. If
necessary, use a series supporting this function.)
(3) Setting the built-in Pulsecoder-based feedback dummy function

Setting the function bit shown below enables ignoring of alarms
related to the servo amplifier and built-in Pulsecoder for an axis not
connected to a servo control circuit.
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) DMY
2009 (FS30i, 16i)
DMY (#0) Specifies whether to enable the serial feedback dummy function as
follows:
0: To disable
1: To enable
1788 (FS15i) Set 0.

2165 (FS30i, 16i)
To use the serial feedback dummy functions, a non-zero value must be
entered as the motor ID number.
1874 (FS15i) Motor ID number

2020 (FS30i, 16i)
Enter an appropriate non-zero value.
Example) 252
- 272 -
(4) Handling of dummy axes in the i series CNC

Usually in the i series, the number of amplifiers must match that of
axes. A dummy axis can be set normally if the axis to be set as the
dummy axis has an amplifier. However, if an attempt is made to set an
axis that does not have an amplifier as a dummy axis, an alarm may be
issued, indicating that amplifiers are insufficient.
In such a case, make FSSB settings as if a series of existing amplifiers
were followed by another amplifier.
Example When there are only two amplifiers for a 3-axis NC

AMP1 AMP2 Dummy axis
(X axis) (Z axis) (Y axis)
X 000.000
Y 000.000
Z 000.000 FSSB
Three axes including the Set a parameter for the

There are only two
X-axis, Y-axis, and Y-axis as if an amplifier
amplifiers.
Z-axis are declared on for the Y-axis were
the CNC. present at the end.
Let us consider how to make the Y-axis (second axis) a dummy axis in
the above configuration.
Set up the parameters as follows:
(Series 15i-B,16i-B, and so on)
No.1023 X:1 Y:2 Z:3
No.1902 bit1=0, bit0=1
No.1905 bit0 X:0 Y:0 Z:0
No.1910=0
No.1911=2
No.1912=1 ← Add a dummy axis.
Nos.1913 to 1919=40
Nos.1970 to 1989=40
No.2009 bit0 Y:1
No.2165 Y:0
No.1023 X:1 Y:2 Z:3
No.1902 bit1=0, bit0=1
No.1905 bit0 X:0 Y:0 Z:0
No.14340= 0
No.14341= 2
No.14342= 1
Nos.14343 to 14375= -96
No.2009 bit0 Y:1
No.2165 Y:0
* For detailed descriptions about FSSB-related setting, refer to the

respective CNC parameter manuals.
- 273 -
(5) Separate detector-based dummy feedback

The separate detector-based dummy feedback function is intended to
ignore alarms for an axis when the separate detector has been
disconnected from the axis temporarily. Set the following bit.
#7 #6 #5 #4 #3 #2 #1 #0
1745 (FS15i) FULDMY
2205 (FS30i, 16i)
FULDMY (#2) Specifies whether to enable the separate detector-based dummy
feedback function as follows:
0: To disable
1: To enable
NOTE
1 The relationships of this function with the built-in
Pulsecoder-based serial feedback dummy function
are as follows:
• When only the built-in Pulsecoder-based serial
feedback dummy function is enabled:
Alarms related to the built-in Pulsecoder and
amplifier are ignored.
• When only the separate detector-based dummy
feed-back function is enabled:
Alarms related to the separate detector are
ignored.
• When both the functions are enabled:
Alarms related to the built-in Pulsecoder,
separate detector, and amplifier are ignored.
2 When using the serial feedback dummy function,
match the control cycle (HRV) with other axes
(non-dummy axes).
Related parameter numbers:
No.2004, No.2013 #0, No.2014 #0 (Series 30i, 16i)
No.1809, No.1707 #0, No.1708 #0 (Series 15i)
- 274 -
4.9.2 How to Use the Dummy Feedback Functions for a Multiaxis

Servo Amplifiers when an Axis is not in Use
If an axis connected to a multiaxis amplifier is not in use, it is
necessary to set the dummy function bit described in Subsec. 4.9.1 and
connect a dummy connector to the amplifier.
Information about dummy connector Location

Jumper between pins 11 and 12. JFx
When the servo software indicated below is used, the setting of the
parameter below enables a multiaxis amplifier to be operated without
inserting a dummy connector.
Series 90D0/L(12) and subsequent editions
Series 90E0/L(12) and subsequent editions
Series 90B1/F(06) and subsequent editions
Series 90B8/F(06) and subsequent editions
#7 #6 #5 #4 #3 #2 #1 #0
No.2692(FS15i) DMCON
No.2279(FS30i,16i
)
DMCON(#0) In emergency stop cancellation with the dummy function enabled:
0: The ready signal is not output to the amplifier.
1: The ready signal is output to the amplifier.
- 275 -
4.10 BRAKE CONTROL FUNCTION
(1) Overview
This function prevents the tool from dropping vertically when a servo
alarm or emergency stop occurs. The function prevents the motor from
being immediately deactivated, instead keeping the motor activated
for the period specified in the corresponding parameter, until the
mechanical brake is fully applied.
(2) Hardware configuration

CNC Servo amplifier (αiSV) Power Supply (αiPS)
System software Servo software

<3>
Timer built into

<1> <2> amplifier
Communication between amplifiers
(Max400ms)
FSSB
<5>
Activation
OFF Main power
PMC Brake control timer supply
(No.2083) AC200V/400V
X ～
Z
Brake signal
<4>
Emergency stop signal
Fig. 4.10 (a) Example of configuration
The numbers of the following descriptions correspond to those in the

figure:
<1> Applicable system software
Any system soft can be used.
<2> Applicable servo software
- 276 -
<3> Servo amplifier

For an axis that uses the brake control function, the use of a
1-axis servo amplifier is recommended. See NOTE below.
For an axis to which the brake control function is not applied,
any servo amplifier can be used.
NOTE
If you want to control the brake for an axis with a
2-axis or 3-axis amplifier, specify the brake control
parameter for all axes on the multiaxis amplifier
including the target axis. If an alarm is generated
for any of the axes connected to the 2-axis or
3-axis amplifier, brake control does not operate
effectively.
<4> Emergency stop signal

With the αi series, a timer for the emergency stop signal is built
into the αiSV. While motor activation is kept by brake control,
the timer in the αiSV is used to extend the activation time that
lasts until the emergency stop signal operates. Motor deactivation
can be delayed by the αiSV for 50 ms to 400 ms. To delay motor
deactivation by brake control for 400 or more, insert a timer in
the contact signal of the emergency stop signal and +24V, and
delay the emergency stop signal to be input to the αiPS, as
traditionally done. (For αiSV timer setting, see Item (3) "Setting
parameters" below.)
αiPS αiSP αiSV
Emergency
(To delay motor stop contact CX4
deactivation for
2
400 ms or more,
ESP :
a timer is :
required.) 3 : :
+24 V : :
CX3
1
~
Coil 3
MCC
Fig. 4.10 (b) αi series amplifier
<5> 200/400 VAC

If the 200 VAC or 400 VAC supply to the servo amplifier is cut,
the brake control function cannot operate.
To cause the brake control function to work effectively even at a
power break, apply the power brake machine protection function.
- 277 -

<1> Brake control function enable/disable bit
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) BRKC
2005 (FS30i, 16i)
BRKC (#6) 1: The brake control function is enabled.
<2> Activation delay

1976 (FS15i) Brake control timer
2083 (FS30i, 16i)
[Increment system] msec
(Example)
To specify an activation delay of 200 ms, set the brake control
timer usually with 200 (appropriately). Do not set it with 500 or
greater. Also set the timer connected to the emergency stop
contact with the same value as set in the parameter.
<3> Setting the emergency stop timer built into the αiSV
#7 #6 #5 #4 #3 #2 #1 #0
1750 (FS15i) ESPTM1 ESPTM0
2210 (FS30i, 16i)
ESPTM0 (#5), ESPTM1 (#6) Set a period of time from the input of the emergency stop signal into
the αiPS until emergency stop operation is actually performed in the
servo amplifier (αiSV).
ESPTM1 ESPTM0 Delay time
0 0 50 ms (default)
0 1 100ms
1 1 200ms
1 1 400ms
When using brake control, set a time longer than the setting of the
brake control timer (No. 1976 for Series 15i or No. 2083 for Series 16i
and so on).
NOTE
For those axes that are connected to a 2-axis
amplifier or 3-axis amplifier, the parameters above
need to be set in the same way.
(4) Detailed operation

Suppose that there is a machine having horizontal and vertical axes
of motion. When a servo alarm (*) occurs on the horizontal axis but no
error occurs on the vertical axis, the MCCs of the amplifiers for all
axes are turned off. When the emergency stop button is pressed, the
MCCs of the amplifiers for all axes are turned off.
- 278 -
Standard machines have a mechanical brake that prevents the tool

from dropping vertically in such cases. The mechanical brake may
actually function according to the timing shown in Fig. 4.10 (c). If this
occurs, the tool will drop vertically, causing the tool or workpiece to
be damaged.
This function changes the timing to force MCC off, using a software
timer, thus preventing the tool from dropping. Fig. 4.10 (d) shows the
timing diagram.
Alarm or emergency
stop signal
ON
Mechanical brake OFF
Servo amplifier
MCC off
Delay (Td)
*ESP signal to
αiPS (+24V)
The tool drops vertically.
Fig. 4.10 (c)
Alarm or
emergency stop
signal ON
OFF
(*) With the αi servo amplifier, the Mechanical brake
operation (Section A) of the 50 to 100 ms (approximately)
*ESP signal in the αiSV can be Servo amplifier
delayed for up to 400 ms by MCC off
setting the parameter for the
emergency stop timer built into Brake control timer: Should be longer
the amplifier. So, when the (approximately 200 ms) than the time (50 to 100 ms)
*ESP signal to during which the mechanical brake is applied.
brake control timer is set to less
than 400 ms, no external timer is αiPS (+24V)
required for the *ESP signal to
be input to the αiPS. *ESP signal in
Section A
αiSV
(*)
The control current The control The mechanical

sustains the tool. current and brake sustains the
mechanical brake tool.
sustain the tool.
Fig. 4.10 (d)
NOTE
1 The servo alarm mentioned in the above description
refers to a servo alarm detected by the software (OVC
alarm, motor overheat alarm, software disconnection
alarm, etc.), an alarm detected by the servo amplifier, or
a servo alarm detected by the CNC (excessive error).
If a servo alarm occurs on the axis using this function,
no brake control is performed on the axis (except for a
motor overheat alarm).
2 For brake control, use the SA signal (F0.6, which is
common to all axes).
- 279 -
4.11 QUICK STOP FUNCTION
The functions described below prevent the tool from colliding with the
machine or workpiece by reducing the distance required for the motor
to come to a stop if a usual emergency stop condition occurs or if a
separate detector disconnection alarm, overheat alarm, or OVC alarm
is issued.
4.11.1 Quick Stop Type 1 at Emergency Stop
(1) Overview
This function reduces the stop distance by resetting the velocity
command for a servo motor to 0 at a position where an emergency
stop signal is detected for the servo motor. To further reduce the stop
distance required for the motor to stop, use quick stop type 2 at
emergency stop described in Subsec. 4.11.2.


#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) DBST
2017 (FS30i, 16i)
DBST (#0) Specifies whether to enable quick stop type 1 at emergency stop as
follows:
0: To disable
1: To enable
To use the quick stop at emergency stop, enable the brake control
function to all axes, which use the quick stop function.
- 280 -
(Brake control function)

#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) BRKC
2005 (FS30i, 16i)
BRKC (#6) Specifies whether to enable brake control function as follows:
0: To disable
1: To enable
NOTE
When only the brake control function is set, a
gradual stop occurs with the torque limit reduced to
70%.
When the quick stop at emergency stop is enabled,
a gradual stop occurs with the torque limit set to
100%, so that the stop distance is reduced.

2083 (FS30i, 16i)
[Unit of data] ms
[Setting value] 50 to 100
(4) Timing diagram

Emergency stop signal
Quick stop function
Dynamic brake
Deceleration
by quick stop Deceleration by
function dynamic brake
Motor speed
Fig. 4.11.1 (a) Timing diagram of quick stop function
(5) Connection of amplifier

PSM SPM SVM
Emergency stop contact
(No timer is necessary.)
CX4
2
ESP : :
3 : :
+24 V : :
CX3
1
∼
Coil 3
MCC
Fig. 4.11.1 (b) αi series amplifier
- 281 -
4.11.2 Quick Stop Type 2 at Emergency Stop
(1) Overview
This function returns a servo motor to a position where an emergency
stop signal is detected for the servo motor, thereby assuring a shorter
stop distance than with quick stop type 1 at emergency stop.
Diagram for comparing stop distances
No stop distance
reduction function
Type 1
Type 2 Return after some overshoot
Emergency stop signal detected


#7 #6 #5 #4 #3 #2 #1 #0
1744 (FS15i) DBS2
2204 (FS30i, 16i)
DBS2 (#7) Specifies whether to enable quick stop type 2 at emergency stop as
follows:
0: To disable
1: To enable
NOTE
1 Like type 1, type 2 requires that the brake control
parameter be set.
2 The method of connecting the amplifier for type 2 is
the same as for type 1.
3 If both type 1 and type 2 function bits are set, type
2 function is assumed.
- 282 -
4.11.3 Lifting Function Against Gravity at Emergency Stop
4.11.3.1 Lifting function against gravity at emergency stop

(1) Overview
This function is intended to lift and stop the vertical axis (Z-axis) of a
vertical machining center when the machine comes to an emergency
stop or power failure.

Series 90B0/P(16) and subsequent editions

Because this function uses quick stop at emergency stop type 2, the
following function bit must be set to 1 (enable). （Quick stop type 1 at
emergency stop (bit 0 of No. 1959 (Series 15i, etc.) or bit 0 of No.
2017 (Series 30i, 16i, etc.) is not needed.)
#7 #6 #5 #4 #3 #2 #1 #0
1744 (FS15i) DBS2
2204 (FS30i, 16i)
DBS2 (#7) Specifies whether to enable quick stop type 2 at emergency stop as
follows:
0: To disable
1: To enable
2786 (FS15i) Distance to lift

2373 (FS30i, 16i)
This parameter is for determining a distance to lift at an emergency
stop. The larger the value, the larger becomes the distance to lift.
[Unit of data] Detection unit or 1µm (→See Subsec.4.11.3.3.)
[Recommended value] Detection unit 1µm : Approximately 500
Detection unit 0.1µm : Approximately 5000
- 283 -
NOTE
1 If the brake is in use, it starts working while the
vertical axis is being lifted. So the distance through
which the axis is actually lifted differs from the setting.
2 Whether the parameter values is positive or negative
matches whether the machine coordinate value is
positive or negative.
3 Using this function causes the load to stop after
moving it to one side of the machine. So, it should be
used for the vertical axis (Z-axis) of a vertical
machining center in which an axis retracts in a fixed
single direction at an emergency stop.
2787 (FS15i) Lifting time

2374 (FS30i, 16i)
This parameter determines the lifting time as measured from the time
of an emergency stop. The distortion easing function is executed after
the lifting time has elapsed. This function is intended to decrease the
amount of machine elastic strain that can increase when a vertical axis
is lifted when the machine is about to apply the brake. Executing this
function can reduce the shock that may occur when the axis drops
because the servo amplifier stops energizing. The initial value of the
function is a quarter of the distance to lift.
(See the following figure.)
[Unit of data] ms
[Recommended value] Approximately 16 or 24 ms
NOTE
1 Specify an integer multiple of 8 as the lifting time
2 To use the lifting function against gravity at
emergency stop, specify 8 ms or longer as the lifting
time.
3 If the distortion easing function is not used, specify
the time longer than or equal to the one set in the
brake control timer as the lifting time.
• Velocity command
Vertical axis lifting
Distortion
easing
function
Lifting time
Fig. 4.11.3 (a) Velocity command
- 284 -
• Motor position waveform

Time specified in the brake control timer
Distortion easing function: Decreases

the machine elastic strain that increases
The vertical axis is lifted. when the vertical axis is lifted.
The distortion easing function

decreases the shock that may occur
when the servo motor is de-energized.
Emergency stop input Energizing by the amplifier is turned off.
Fig. 4.11.3 (b) Motor position waveform
Using this function requires specifying the following brake control

parameters.
Brake control function bit

#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) BRKC
2005 (FS30i, 16i)
BRKC(#6) The brake control function is:
0 : Disabled.
1 : Enabled ← Use this setting.
Energizing delay time

2083 (FS30i, 16i)
[Unit of data] ms
[Recommended value] 50 to 100 ms
NOTE
If the vertical axis (Z-axis) is connected to a
multiaxis amplifier, it is necessary to enable the
brake control function for all the axes connected to
the multiaxis amplifier.
Set the time from the instant when an emergency stop signal is input
to αiPS to the instant when the emergency stop function works in the
servo amplifier.
#7 #6 #5 #4 #3 #2 #1 #0
1750 (FS15i) ESPTM1 ESPTM0
2210 (FS30i, 16i)

0 0 50ms (default value)
0 1 100ms
1 0 200ms
1 1 400ms
- 285 -
It is necessary to specify the time longer than or equal to the brake

control timer value.
If the brake control timer value is 100 ms, for example, specify
ESPTM1 (bit 6) and ESPTM2 (bit 5) to be, respectively, 0 and 1 (100
ms).
NOTE
For a multiaxis amplifier, the largest of the values
specified for the axes is assumed to be the delay
time.
(4) Example of using the parameter

The following example shows the effect of using the lifting function
against gravity at emergency stop for the vertical axis (Z-axis). In this
example, the distance to lift is 500, and the lifting time is 16 ms. The
vertical axis of the graph is graduated 2 µm/div.
Motor position waveform
Distortion easing
function
Lifting time
Emergency stop input Energizing by the

amplifier is turned off.
Fig. 4.11.3 (c) Motor position waveform
As seen from the graph, the motor is lifted through a large distance
after an emergency stop signal is input. The graph also shows that the
distortion easing function decreased the machine elastic strain and
kept the motor from falling when the amplifier stopped energizing.
Also as seen from the graph, the position where the motor finally
rested is higher than the position where the motor was before the
emergency stop signal was input.
NOTE
1 In this example, positive coordinates of the
machine coordinate system correspond to the
direction in which the axis is lifted.
2 Variation occurs in the position where the Z-axis
stops depending on the direction in which the
Z-axis is moving before an emergency stop. When
tuning the parameter, it is necessary to take, into
account, both the position where the motor rests
before the axis is moved up and the position where
the motor rests after the axis is moved down.
- 286 -
4.11.3.2 Function based on the DI signal for switching the distance to

lift
(1) Overview
With the lifting function against gravity at emergency stop, switching
between two types of parameters for specifying a distance to lift is
enabled based on the DI signal of the PMC. By setting either
parameter to 0, lift operation can be temporarily disabled.

(Series 16i-B,18i-B,21i-B,Power Mate i)
Series 90B1/H(08) and subsequent editions
(Series 0i-C)
To use this function, the following system software is needed:
B0H1/BDH1-24 and subsequent editions (Series 16i/18i-MB)
B0K1/BDK1 -01 and subsequent editions (Series 16i/18i-MB)
B1H1/BEH1-24 and subsequent editions (Series 16i/18i-TB)
B1K1/BEK1 -01 and subsequent editions (Series 16i/18i-TB)
BDH5-14 and subsequent editions (Series 18i-MB5)
BDK5-01 and subsequent editions (Series 18i-MB5)
DDH1-24 and subsequent editions (Series 21i-MB) (*1)
DDK1-01 and subsequent editions (Series 21i-MB) (*1)
DEH1-24 and subsequent editions (Series 21i-TB) (*1)
DEK1-01 and subsequent editions (Series 21i-TB) (*1)
D4B1/D4C1-01 and subsequent editions (Series 0i-MC) (*1)
D6B1/D6C1-01 and subsequent editions (Series 0i-TC) (*1)
D6D1-01 and subsequent editions (Series 0i-TTC) (*1)
88E1-03 and subsequent editions (Power Mate i-D) (*2)
88E3-01 and subsequent editions (Power Mate i-D) (*2)
88F2-10 and subsequent editions (Power Mate i-H) (*2)
88F3-01 and subsequent editions (Power Mate i-H) (*2)
(*1) With these NCs, PMC-SB7 is required.

(*2) With these NCs, PMC-SB6 is required.
(*3) This function cannot be used with the Series 15i.
(*4) The Series 30i supports this function, starting with the first
edition.
- 287 -
(3) Switching signal

Signal for switching the distance to lift for the lifting function against gravity at
emergency stop
#7 #6 #5 #4 #3 #2 #1 #0
Gn323 SWDBS8 SWDBS7 SWDBS6 SWDBS5 SWDBS4 SWDBS3 SWDBS2 SWDBS1
[Classification] Input signal

[Function] This signal is used to switch the distance to lift when the lifting
function against gravity at emergency stop is enabled. A number
suffixed at the end of the signal represents the number of each
controlled axis.
(Details of operation)
• When this signal (SWDBSx) is set to 0, the distance to lift for the
lifting function against gravity at emergency stop follows the
value set in No. 2373.
• When this signal (SWDBSx) is set to 1, the distance to lift for the
lifting function against gravity at emergency stop follows the
value set in No. 2173.
• The distance to lift depends on the state of this signal (SWDBSx)
present when the emergency stop command is input. (If this
signal is changed during lift operation after the emergency stop
command is input, the change does not become effective until the
lift operation is completed and the excitation is turned off.)
• Among the parameters related to the lifting function against
gravity at emergency stop, the parameters other than those
related to the distance to lift are common, regardless of the state
of this signal (SWDBSx).

Set the parameters below in addition to the parameters for the lifting
function against gravity at emergency stop.
- Distance to lift (when SWDBSx=0)

2373(FS30i,16i)
[Recommended value] Detection unit 1µm : Approximately 500 or -500
Detection unit 0.1µm : Approximately 5000 or -5000
This parameter is effective only when the signal (SWDBSx) for

switching the distance to lift for the lifting function against gravity at
emergency stop is set to 0.
To disable lift operation when (SWDBSx) = 0, set 0 in this parameter.
- 288 -
- Distance to lift (when SWDBSx=1)

2173(FS30i,16i)
[Recommended value] Detection unit 1µm : Approximately 500 or -500
Detection unit 0.1µm : Approximately 5000 or -5000
This parameter is effective only when the signal (SWDBSx) for

switching the distance to lift for the lifting function against gravity at
emergency stop is set to 1.
NOTE
1 When a brake is used, brake application starts
during lift operation, so that the set value does not
match the actual lift distance.
2 The parameter polarity matches the polarity of the
machine coordinate system.
3 Use this function only when lift operation does not
cause a mechanical interference.
- 289 -
4.11.3.3 Method of setting a distance to lift in µm

(1) Overview
When the servo software below is used with the lifting function
against gravity at emergency stop, the parameter for specifying a
distance to lift can be set in [µm], independently of the detection unit.
With this function, a large distance to lift can be used when a small
detection unit is used.


#7 #6 #5 #4 #3 #2 #1 #0
- DUNIT
2298(FS30i)
DUNIT(#7) When the lifting function against gravity at emergency stop is used,
the function that enables the parameter for specifying a distance to lift
to be set in µm, independently of the detection unit, is
0: Not used
1: Used
• When this function is enabled, the parameter (No. 2373 or No.
2173) for specifying a distance to lift for the lifting function
against gravity at emergency stop can be set in µm,
independently of the detection unit.
• When this parameter has been set, the power must be turned off
• If this function is used with a CNC that does not support the
function for sending the detection unit to servo software, an
illegal parameter setting alarm (detail number 2982) is issued.
NOTE
The series and editions of CNC software that support the function
for sending the detection unit are as follows:
FS30i-A : G002,G012,G022,G032/20.0 and subsequent editions
: G003,G013,G023,G033/1.0 and subsequent editions
FS31i-A5 : G121,G131/20.0 and subsequent editions
FS31i-A : G101,G111/20.0 and subsequent editions
FS32i-A : G201/20.0 and subsequent editions
: G203/1.0 and subsequent editions
- 290 -
4.11.4 Quick Stop Function for Hardware Disconnection of Separate

Detector
(1) Overview
This function reduces the stop distance by resetting the velocity
command for a servo motor to 0 when the separate detector for the
servo motor encounters a hardware disconnection condition. It also
causes the other axes to stop sooner than they would when a usual
alarm occurs.


#7 #6 #5 #4 #3 #2 #1 #0
1745 (FS15i) HDIS HD2O
2205 (FS30i, 16i)
HD2O (#5) The quick stop function for hardware disconnection of separate
detector is:
0: Not applied to axes under synchronous control.
1: Applied to axes under synchronous control.
HDIS (#4) Specifies whether to enable quick stop function for hardware
disconnection of separate detector as follows:
0: To disable
1: To enable
1976 (FS15i ) Brake control timer

2083 (FS30i, 16i)
[Unit of data] ms
[Setting value] 100
- 291 -
NOTE
1 When applying this function to axes under
synchronous control (including simple synchronous
control), follow the steps below:
1) Change the servo axis setting (No. 1023) of the
two axes under simple synchronous control to
set an odd-numbered axis as the master axis
and an even-numbered axis ((master axis
number) + 1) as the slave axis.
2) Set HD2O (bit 3) to 1 for both axes under
synchronous control.
2 This function is implemented using part of the
"unexpected disturbance torque detection function"
option. So, using it requires that option.
3 Usually, when a separate detector disconnection
alarm occurs for an axis, not only this axis but also
the others are brought to an emergency stop. If an
unexpected disturbance torque detection group
function (not supported in the Series 15i) is set up,
however, only the axes in the same group as the
axis for which an alarm condition has occurred are
brought to an emergency stop.
4 If the value (No. 1738 for the Series 15i or No.
1880 for the Series 30i, 16i, and so on) specified
as an interval between the detection of an
unexpected disturbance torque and the occurrence
of an emergency stop is small, it may impossible to
keep the sufficient stop time. The value should be
at least greater than or equal to the one specified in
the brake control timer parameter (there is no
problem with a setting value of 0, because it means
200 ms).
- 292 -
4.11.5 Quick Stop Function for Separate Serial Detector Alarms
(1) Overview
This function reduces the stop distance by setting the velocity
command for the servo motor to 0 when the separate serial detector is
placed in an alarm state indicated below. With this function, motion
on the axes other than the axis with which any of the alarms below is
issued is also stopped quicker than in the case of an ordinary alarm.
Alarm number Description

SV0380 BROKEN LED (EXT)
SV0381 ABNORMAL PHASE (EXT)
SV0382 COUNT MISS (EXT)
SV0383 PULSE MISS (EXT)
SV0384 SOFT PHASE ALARM (EXT)
SV0385 SERIAL DATA ERROR (EXT)
SV0386 DATA TRANS. ERROR (EXT)
SV0387 ABNORMAL ENCODER (EXT)

Series 90B1/E(05) and subsequent editions

#7 #6 #5 #4 #3 #2 #1 #0
2695( FS15i ) FSAQS
2282（FS30i,16i）
FSAQS(#5) The quick stop function for separate serial detector alarms is:
0: Disabled
1: Enabled
#7 #6 #5 #4 #3 #2 #1 #0
1745( FS15i ) HD2O
2205(FS30i,16i)
HD2O(#3) When a separate serial detector alarm is issued, two-axis simultaneous
stop is:
0: Disabled
1: Enabled
* This parameter can be used with either the quick stop function
for hardware disconnection of separate detector (bit 4 of No.
2205=1) or the quick stop function for separate serial detector
alarms (bit 5 of No. 2282=1).
- 293 -
4.11.6 Quick Stop Function at OVL and OVC Alarm
(1) Overview
This function reduces the stop distance for a servo motor when an
OVL (motor overheat or amplifier overheat) or OVC alarm condition
is detected for the servo motor. It also causes the other axes to stop
sooner than they would when a usual alarm occurs.


#7 #6 #5 #4 #3 #2 #1 #0
2600 (FS15i) OVQK
2212 (FS30i, 16i)
OVQK (#7) Specifies whether to enable quick stop function at the OVC and OVL
alarm as follows:
0: To disable
1: To enable
NOTE
The operation of this function is performed by using
part of the unexpected disturbance torque
detection function. Therefore, to use this function,
the option for the “unexpected disturbance torque
detection function” is required.

2083 (FS30i, 16i)
[Unit of data] ms
[Setting value] 100
- 294 -
4.11.7 Overall Use of the Quick Stop Functions

To sum up, setting up the following parameters as stated can reduce
the stop distance for an emergency stop, separate detector hardware
disconnection, and OVL and OVC alarm occurrence.
<1> Specify the unexpected disturbance torque detection option.

<2> Specify quick stop type 2 at emergency stop.
<3> For a vertical axis, specify the function for lifting up a vertical
axis at emergency stop, if required.
<4> For a full-closed axis, set the quick stop function for hardware
disconnection of separate detector or the quick stop function for
separate serial detector alarms. Also if they are subjected to
synchronous control, set the HD2O bit.
<5> Specify the quick stop function at the OVC and OVL alarm.
<6> Set the brake control function bit and the brake control timer.
- 295 -

FUNCTION Optional function
4.12.1 Unexpected Disturbance Torque Detection Function
(1) Overview
When a tool collides with the machine or workpiece, or when a tool is
faulty or damaged, a load torque greater than that experienced during
normal feed is imposed.
This function monitors the load torque to the motor at servo
high-speed sampling intervals. If it detects an abnormal torque, it
brings the axis to an emergency stop by issuing an alarm, or reverses
the motor by an appropriate amount.
In addition, the function enables the PMC to be used to switch the
speed at warning occurrence or load fluctuation.
NC software - An application on the PMC PMC ladder
PMC
uses a PMC ladder.
window
Disturbance load
Set unexpected
torque data disturbance torque
detection level.
Processes motor stop

TCMD Calculates Monitors disturbance
disturbance load load torque unexpected
Servo software
torque to the motor (at 1 ms intervals) disturbance torque
detection function
Amplifier Monitoring is performed at 1 ms

intervals to reduce stop time.
Actual acceleration
Collision
Table
Motor
Fig. 4.12.1 Overview of unexpected disturbance torque detection

- 296 -
(3) Parameter adjustment methods

<1> Use SERVO GUIDE to observe the motor speed (SPEED) and
estimated disturbance torque (DTRQ).
(Example of channel settings on SERVO GUIDE)
(See Sec. 4.22 for detailed descriptions about how to use the
SERVO GUIDE.)
<2> Switch on the CNC.

<3> Enable the unexpected disturbance torque detection function
#7 #6 #5 #4 #3 #2 #1 #0
1958 (FS15i) ABNT
2016 (FS30i, 16i)
ABNT (#0) Specifies whether to enable the unexpected disturbance torque
detection function as follows:
0: To disable
1: To enable
Moreover, be sure to set also the following parameters.
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) IQOB
2200 (FS30i, 16i)
IQOB Specifies whether to eliminate influence of control voltage saturation
when estimating disturbance, as follows:
0: Not to take influence of control voltage saturation when
estimating disturbance into consideration
1: To eliminate influence of control voltage saturation when
estimating disturbance
- 297 -
<4> Set up the parameters related to the observer.

2050 (FS30i, 16i)
[Standard setting value] 956 → To be changed to 3559.
[Standard setting value] 264 → To be changed to 1420

2051 (FS30i, 16i)
[Standard setting value] 510 → To be changed to 3329.
[Standard setting value] 35 → To be changed to 332
NOTE
When using this function together with the
observer, do not modify the standard setting of the
parameter above.
Observer:
Bit 2 of No.1808 (Series 15i)
Bit 2 of No.2003 (Series 30i, 16i, and so on)
<5> Make adjustments on the POA1 observer parameter.
1859 (FS15i) Observer parameter (POA1)

2047 (FS30i, 16i)
Turn the servo motor to perform linear back and forth operation at a
speed equal to about 50% of the rapid traverse rate, and observe the
motor speed (SPEED) and the estimated disturbance value (DTRQ).
The waveform observed before the adjustment should show one of the
following features:
Motor velocity
Estimated
disturbance
value
Insufficient POA1 value Excessive POA1 value

At acceleration: At acceleration:
Undershoot on estimated Overshoot on estimated
disturbance value disturbance value
At deceleration: At deceleration:
Overshoot on estimated Undershoot on estimated
disturbance value disturbance value
- 298 -
Make adjustments on the POA1 parameter so that neither an

overshoot nor an undershoot will not be observed on the estimated
disturbance value at acc./dec. After adjustment, the waveforms shown
below should be obtained.
(A clear waveform like the one shown below may not be obtained in
some machines. In such machines, find the POA1 value that can
minimize the overshoot and undershoot by watching the estimated
disturbance waveform at acc./dec.)
Motor velocity
Proper POA1
Estimated
disturbance valu
NOTE
The POA1 parameter is related to the load inertia ratio
parameter ("velocity gain" on the servo screen) through
the inside of the software. When the load inertia ratio
parameter is changed, the POA1 parameter must also be
changed. So, first determine the load inertia ratio (velocity
gain) when adjusting the servo.
If you must change the load inertia ratio (velocity gain)
after the POA1 parameter is determined, re-set the POA1
parameter using the following expression.
(New POA1 value) =
(Previous POA1 value) ×
(Load inertia ratio value set after adjustment+256) /
(Load inertia ratio value set before adjustment+256)
Load inertia ratio:
No. 1875 (Series 15i), No. 2021 (Series 16i and so on)
The velocity gain magnification (in cutting or high-speed
HRV current control) does not affect the setting of POA1.
(Details)
The observer estimates a disturbance torque by subtracting the torque
required for acc./dec. from the entire torque. The torque required for
acc./dec. is calculated using a motor model. The POA1 parameter
corresponds to the inertia of the motor model. If the parameter value
differs from the actual value, it is impossible to estimate a correct
disturbance torque. To detect an unexpected disturbance torque
correctly, therefore, you must adjust the value of this parameter.
An estimated disturbance value when a usual condition is supposed to
be related only to frictional torque (for the horizontal axis), and
proportional to the velocity. Therefore, a program, like the one used
for adjustment, that merely repeats simple acc./dec. is supposed to
generate a trapezoidal estimated disturbance torque waveform like a
velocity waveform.
- 299 -
<6> For the vertical axis, adjust the torque offset. (This is
unnecessary for the horizontal axis.)
For the vertical axis, the estimated disturbance value is not
centered at level 0. Torque offset adjustment is done to center the
estimated disturbance value at level 0.
1980 (FS15i) Torque offset parameter

2087 (FS30i, 16i)
[Unit of data] TCMD unit (7282 with the maximum current value of the amplifier)
(Example of torque offset setting)
Estimated disturbance values for constant-velocity movements in
the + direction and - direction are read. In the figure below,
minimum value A (signed) is read in a movement in the +
direction, and maximum value B (signed) is read in a movement
in the - direction. A torque offset parameter setting is given using
the following expressions:
A [Ap] + B [Ap]
Torque offset = × 3641
Maximum amplifier current value [Ap]
Estimated disturbance
value level 0
6.6A
Maximum
value B
Estimated disturbance
Minimum value center line
value A Influence by gravity
If you read the minimum value A and maximum value as –8.6 [Ap]
and –4.5 [Ap] in the above chart (the amplifier used is rated at 80 [Ap]
maximum), the torque offset parameter = -[(-8.6)+(-4.5)]/80×3641 =
596. The following chart applies when the parameter is set with 596.
- 300 -
When the torque offset parameter is set, be sure to set the following
parameter to 1.
#7 #6 #5 #4 #3 #2 #1 #0
2603 (FS15i) TCPCLR
2215 (FS30i, 16i)
TCPCLR(#1) The function for setting a value for canceling the torque offset at an
emergency stop in the velocity loop integrator is:
0: Disabled
1: Enabled
<7> Compensate for dynamic friction.

(i) Method of canceling a dynamic friction in proportion to
velocity
Measure an estimated disturbance value at a constant
velocity. Then, by assuming this measured value as a
dynamic friction, set the proportional coefficient for a
velocity and dynamic friction compensation value.
1727 (FS15i) Dynamic friction compensation coefficient

2116 (FS30i, 16i)
[Unit of data] See the equation below.
[Valid data range] 0 to 264 (Series 9096, Series 90B0/A(01) to D(04) editions)
-264 to 264 (Series 90B0/E(05) and subsequent editions, Series 90B1,
Series 90B5, Series 90B6, Series 90B8, Series 90D0, or Series 90E0)
[Measurement velocity] Rotary motor: 1000 min-1, Linear motor: 1000 mm/s
Measure an estimated disturbance value at a measurement velocity,
then set the results of calculations made according to the table below.
Dynamic friction Estimated disturbance value [Ap]
= × 440
compensation coefficient Maximum amplifier current value [Ap]
NOTE
If the measurement velocity is too high, lower the
measurement velocity, and measure the estimated
disturbance value. By proportional calculation,
obtain the estimated disturbance value at the
above measurement velocity.
Dynamic friction compensation value
No.1727(Series 15i)
No.2116(Series 16i and
so on)
Dynamic friction
compensation coefficient
Velocity
-1
1000 min (rotary motor)
1000 mm/s (linear motor)
Set a compensation value at a measurement
velocity, and correct the value proportional to the
velocity as a dynamic friction.
- 301 -
(Example of setting for a rotary motor)

- Suppose that the estimated disturbance value at 1000 min-1 is 1
[Ap] (the maximum amplifier current value is 40 [Ap]).
Dynamic friction compensation coefficient = 1/40 × 440 = 11
Dynamic friction compensation Dynamic friction compensation

before setting after setting
Read value
A(A)
These portions represent The effect of dynamic friction is

disturbances due to dynamic reduced, and stable estimated
friction. An adjustment is made to disturbance values are obtained.
eliminate these portions.
(ii) Method of setting a dynamic friction as "portion

proportional to velocity + constant portion" and imposing a
limit
If the compensation value for stop time to low-velocity
movement is insufficient in adjustment of (i), set a dynamic
friction compensation value in the stop state. If the
compensation value for high-speed movement is excessive,
a limit is imposed on the compensation value.
Dynamic friction compensation value
No.2759(Series 15i)
No.2346(Series 16i and
so on) No.1727(Series 15i)
Compensation limit value No.2116(Series 16i and
No.2758(Series 15i) so on)
No.2345(Series 16i and so Dynamic friction
compensation coefficient
on)
Compensation value in the
1000min-1 Velocity
stop time
Set a compensation value in the stop time and

a compensation limit value in addition to a
-1
compensation value at 1000 min .
- 302 -
NOTE
This method can be used with the following servo
software:
(Series 15i-B, 16i-B, 18i-B, 21i-B, 0i-B, 0i Mate-B,
Power Mate i)
2758 (FS15i) Dynamic friction compensation value in the stop state

2345 (FS30i, 16i)
[Unit of data] TCMD unit (7282 when the estimated disturbance value is equivalent
to the maximum current value of the amplifier)
[Measurement velocity] 10 min-1 (rotary motor), 10 mm/s (linear motor)
The absolute value of a setting is used.
2759 (FS15i) Dynamic friction compensation limit value

2346 (FS30i, 16i)
[Unit of data] TCMD unit (7282 when the estimated disturbance value is equivalent
to the maximum current value of the amplifier)
[Measurement velocity] Maximum feedrate
The absolute value of a setting is used.
(Method of setting)
First, measure an estimated disturbance value when a movement
is made at a maximum feedrate on the axis, then set the results of
calculations made according to the table below in "dynamic
friction compensation limit value".
Dynamic friction |Estimated disturbance value [Ap]|
= × 7282
compensation limit value Maximum amplifier current value [Ap]
Next, measure an estimated disturbance value when a movement

is made on the axis at the measurement velocity (10 min-1 or 10
mm/s) for "dynamic friction compensation value in the stop
state", then set the results of calculations made according the
table below in "dynamic friction compensation value in the stop
state".
compensation value in = × 7282
the stop state
- 303 -
Finally, measure an estimated disturbance value when a

movement is made on the axis at the measurement velocity (1000
min-1 or 1000 mm/s) for "dynamic friction compensation
coefficient", then set the results of calculations made according
the table below in "dynamic friction compensation coefficient".
= × 440
compensation coefficient Maximum amplifier current value [Ap]
<8> Set an unexpected disturbance torque detection alarm level.

Perform several different operations (sample machining program,
simultaneous all-axis rapid traverse acc./dec., etc.), and observe
estimated disturbance values, and measure the maximum
(absolute) value.
Then, set up an alarm level.
+ Estimated disturbance value
Maximum
value
-
1997 (FS15i) Unexpected disturbance torque detection alarm level

2104 (FS30i, 16i)
Alarm level conversion uses the following expression.

Unexpected disturbance torque detection alarm level =
|Estimated disturbance value [Ap]|

× 7282+500 to 1000 approximately
NOTE
1 Add some margin (usually about 500 to 1000) to
the alarm level to be set.
2 If the "unexpected disturbance torque detection
alarm level" parameter is 32767, no unexpected
disturbance torque alarm detection is performed.
<9> Set a distance to be retraced at unexpected disturbance torque

detection.
If the retrace amount parameter is 0, the motor stops at the point
where an unexpected disturbance torque was detected. To retract
the tool from the location of collision quickly, set the retrace
distance parameter.
- 304 -
Conceptual diagram illustrating retrace
The tool plunges in at full torque.

No unexpected disturbance torque
detected
The tool go beyond slightly, and returns to
Unexpected disturbance torque the location where the unexpected
detected, but no retrace is performed. disturbance torque was detected.
Unexpected disturbance torque The tool is retracted from the location where
detected, and retrace is performed. the unexpected disturbance torque was
detected to avoid mechanical contact at the
Retrace distance ultimate stop position.
Collision Unexpected disturbance

torque detected
1996 (FS15i) Retrace distance

2103 (FS30i, 16i)
[Setting value] Approximately 3 mm
NOTE
When the tool is moving faster or slower than the
velocity listed below, the tool will not go back even
if this parameter is set. It stops at the location
where an unexpected disturbance torque was
detected.
Let the value set in the retrace distance parameter
be A:
Minimum retract velocity =
A × detection unit (µm) × 60/512 [mm/min]
Example)
When detection unit = 1 µm, and retract amount
setting = 3000, the minimum velocity at which
the tool is retracted is:
Minimum retract velocity =
3000 × 1 × 60/512 = 352 [mm/min]
[2-axis simultaneous retract function at detection of an

unexpected disturbance torque]
Usually, retraction at detection of an unexpected disturbance torque is
performed only on the axis with which the unexpected disturbance
torque is detected. However, when an unexpected disturbance torque
is detected on one position tandem axis, retraction can be performed
on the other position tandem axis as well by setting the parameter
below.

- 305 -

(Setting parameters)
To use the unexpected disturbance torque detection function, set the
following bit to 1 for both the master and slave axes.
#7 #6 #5 #4 #3 #2 #1 #0
2684 (FS15i) RETR2
2271 (FS30i, 16i)
RETR2(#2) With the unexpected disturbance torque detection function, 2-axis
simultaneous retraction is:
0: Not performed
1: Performed
In the parameter for the distance to retract, specify the same value for
both the master and slave axes. If an unexpected disturbance torque is
detected on one of the axes, both axes are retracted.
NOTE
1 This function can be applied only to two axes in
position tandem on the same DSP. Do not use this
function for any axis that has not been set for
position tandem.
2 If different values are specified for the master and
slave axes, an invalid parameter alarm is issued.
(The detail No. of the alarm is 1033.)
<10> Run the machine with the alarm level set up.
If the unexpected disturbance torque detection function works
incorrectly, increase the alarm level.
<11> Now adjustment is completed.
- 306 -
4.12.2 Cutting/Rapid Unexpected Disturbance Torque Detection

Switching Function
(1) Overview
An alarm threshold for unexpected disturbance torque detection is set
separately for cutting and rapid traverse.


A threshold can be set separately for cutting and rapid traverse by
setting the following bit when the unexpected disturbance torque
detection function is used:
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) ABG0
2200 (FS30i, 16i)
ABG0(#3) The cutting feed/rapid unexpected disturbance torque detection
switching function is:
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
2603 (FS15i) ABT2
2215 (FS30i, 16i)
ABT2(#7) Cutting feed/rapid unexpected disturbance torque detection switching
function type-2 is:
0: Disabled.
1: Enabled.
NOTE
1 Set the two bits above. (Servo software was
revised in type-2 to be able to switch even if you
set bit 3 of No.1800 to 1, feed-forward always
enable.)
2 With Series 9096, switching is disabled when bit 3
of No. 1800 is set to 1 (to enable feed-forward in
rapid traverse). The alarm level for cutting is
enabled at all times.
- 307 -
Alarm thresholds for unexpected disturbance torque detection are set

in the following parameters:
1997 (FS15i) Unexpected disturbance torque detection threshold for cutting
2104 (FS30i, 16i) (This parameter is used both in not switching mode and in switching mode.)
1765 (FS15i) Unexpected disturbance torque detection threshold for rapid traverse
2142 (FS30i, 16i)
NOTE
1 When the alarm level for cutting is 32767,
unexpected disturbance torque detection is not
performed during cutting.
2 When the alarm level for rapid traverse is 32767,
unexpected disturbance torque detection is not
performed during rapid traverse. When both
parameters are 32767, unexpected disturbance
torque detection is not performed at any time.
- 308 -
4.12.3 Unexpected Disturbance Torque Detection Switching

Function Depending on Acc.
(1) Overview
This function separately sets a threshold level for unexpected
disturbance torque alarms detected in an acceleration/deceleration
zone where the estimated disturbance value tends to fluctuate. This
function can protect against erroneous detection of an unexpected
disturbance torque alarm in an acceleration/deceleration zone.
1. In a zone where acceleration/deceleration is performed (zone

where extensive acceleration is applied), a higher alarm level can
be set.
2. The influence of acceleration after positioning can be avoided by
setting a timer when returning to the original alarm level after
alarm level switching.

(3) Notes
• When using this function, set the post-acceleration timer (No. 2358).
• This function can be used together with the cutting/rapid unexpected
disturbance torque detection switching function.

(Related parameters)
2755 (FS15i) Acceleration threshold in unexpected disturbance torque detection

2342 (FS16i ,30i)
[Setting value] Let α [mm/s2] be an acceleration rate and let P [mm/pulse] be a
detection unit. Then, the value to be set in the parameter can be found
from the following expression:
α × 64
Setting = (Series 15i, 16i, etc.)
P × 106
α × 16
= (Series 30i)
P × 106
When 0 is set in this parameter, acceleration-based alarm level
- 309 -
2756 (FS15i) Alarm level for high acceleration in unexpected disturbance torque
detection
2343 (FS16i ,30i)
[Unit of data] TCMD
When the absolute value of a specified acceleration rate is equal to or
greater than the setting of No. 2342, the setting of No. 2343 is applied
as an unexpected disturbance torque detection alarm level.
When 0 is set in this parameter, acceleration-based alarm level
2771 (FS15i) Post-acceleration timer in unexpected disturbance torque detection

2358 (FS16i ,30i)
[Unit of data] ms
This parameter maintains a changed alarm level for a timer-set period
even after the specified acceleration rate is reduced below a certain
level.
Velocity
<1> Specified acceleration rate is

Acceleration lower than acceleration
threshold (No. 2342).
No.2342
<2> Period set in post-acceleration

timer (No. 2358) has elapsed.
Alarm level
No.2343
<3> Level returns to level for low
acceleration.
No.2104 or No.2142
No.2358 Time
- 310 -
4.13 FUNCTION FOR OBTAINING CURRENT OFFSETS AT

EMERGENCY STOP
(1) Overview
The current offset is a current feedback offset value arising from the
analog offset voltage of the current detector. If the current offset is
measured incorrectly, motor current feedback can be adversely
affected, resulting in very small motor rotation fluctuations (four
components per motor revolution).
A current offset measurement is made when the power is turned on.
This function performs a current offset measurement not only at
power-on time but also in each emergency stop state.

#7 #6 #5 #4 #3 #2 #1 #0
1741 (FS15i) CROFS
2201 (FS30i, 16i)
CROFS (#0) 1: Enables the current offset to be obtained upon the occurrence of
an emergency stop.
If the above setting is made, the current offset is obtained again during
an emergency stop.
- 311 -
4.14 LINEAR MOTOR PARAMETER SETTING
4.14.1 Procedure for Setting the Initial Parameters of Linear Motors
(1) Overview
The following describes the procedure for setting the digital servo
parameters to enable the use of a FANUC linear motor.
Series 90B3/A(01) and subsequent editions. However, edition
P(16) or later is recommended.
Series 90B7/A(01) and subsequent editions. However, edition
Q(17) or later is recommended.
(Series 20i-B)
(3) Warning
WARNING
1 The linear motor can make an unpredictable
movement, resulting in a very dangerous situation,
if an error is made in linear motor assembly, power
line cabling, detector installation direction setting,
or basic parameter setting.
2 It is recommended to take the following actions
until normal operation is confirmed:
- Lower the excessive error level so that an alarm
is issued immediately when an unpredictable
movement is made.
- Lower the torque limit value to disable abrupt
acceleration.
- Ensure that the emergency stop switch can be
pressed immediately.
(4) Linear encoders
The position and velocity of the linear motor are detected using a
linear encoder. Two types of linear encoders are available:
incremental type and absolute type. The parameter setting and
connection vary according to the type of encoder.
- 312 -
For incremental type

The linear encoder of incremental type is connected to a servo
amplifier via a position detection circuit (A860-0333-T*** or
A860-2033-T***) for linear motor manufactured by FANUC. Values
to be set in parameters vary depending on the signal pitch of the linear
encoder. Therefore, check the signal pitch of the encoder first.
If a position detection circuit (-T201, -T202, -T301, or -T302) having
an interpolation magnification of 2048 is used, it is necessary to
specify additional parameters so that both the maintenance of a
maximum feedrate and the realization of a higher resolution can be
supported.
When a linear motor position detection circuit (A860-2033-T201,
-T202, -T301, -T302) is used, the following servo software is needed.
Series 90B1/K(11) and subsequent editions (Series15i, 16i and so on)
Series 90D0, 90E0/P(16) and subsequent editions(Series 30i and so
on)
Series 90B3 and 90B7 are unusable. (Series 16i and so on)
Series 90D3 and 90E3 are unusable (Series 30i and so on)
Table 4.14.1 (a) lists examples of usable incremental linear encoders.
Table 4.14.1 (a) Examples of usable linear encoders (incremental)

Encoder maker Signal pitch (µm) Model
20 LS486, LS186, etc.
40 LB382, LIDA185, etc.
HEIDENHAIN
2 LIP481
4 LF481R, LIF181, etc.
Mitutoyo 20 AT402
Optodyne 40.513167 LDS
20 RGH22
Renishaw
40 RGH41
SAMTAK
20 FTV, FMV
(FUTABA CORPORATION)
Sony Precision
20 SH12, SH52
Technology Inc.
When a linear encoder of incremental type is used, a linear motor pole

detector (A860-0331-T001,-T002 or A860-2031-T001,-T002) is also
needed.
For absolute type

The linear encoder of absolute type is directly connected to a servo
amplifier. Depending on the resolution of an encoder used, the
parameter setting varies. First, check the resolution. Table 4.14.1(b)
lists examples of absolute type linear encoders currently usable.
Table 4.14.1 (b) Usable linear encoders (absolute)
Encoder maker Resolution (µm) Model
HEIDENHAIN 0.05 (0.1)* LC191F, LC491F
Mitutoyo 0.05 AT353, AT553
* Encoders with resolutions of 0.05 µm and 0.1 µm are available.
- 313 -
NOTE
1 For details of the linear encoders usable with
FANUC linear motors, refer to "FANUC LINEAR
MOTOR LiS series DESCRIPTIONS
(B-65382EN)".
2 For details of the linear encoders, contact the
manufacturer of each linear encoder.
3 To use servo HRV4 control with a linear motor, a
detector that supports servo HRV4 control is
needed. See "(d) Detector" in "(4) Servo HRV4
control hardware" of Subsection 4.2.2.
(5) Parameter settings

Set the parameters according to the procedure below. Note the points
below when setting the parameters.
[Cautions for using incremental linear encoders]
The following parameter setting procedure involves a parameter
to be specified according to the resolution of the linear encoder.
If an incremental linear encoder is to be used, convert the
encoder signal pitch to the resolution for parameter calculation,
using the following equation.
Resolution [µm] = Encoder signal pitch [µm] / 512
Parameter setting procedure (1)
Procedure (1) can be used to initialize the parameters (such as current

gain) necessary to drive a linear motor. After initialization, parameters
depending on the linear encoder resolution (or the value obtained by
dividing the signal pitch of the linear encoder by the interpolation
magnification of the position detection circuit) must be set. Set these
parameters by following parameter setting procedure (2).
Parameters related to initialization

For incremental type, For absolute type
#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) DGPR PLC0
2000 (FS30i, 16i)
DGPR(#1) Set 0. (After initialization, this bit is set to 1 automatically.)
For PLCO (#0), see Table 4.14.1(d) and Table 4.14.1(e).
1806 (FS15i) AMR

2001 (FS30i, 16i)
Specify 00000000.
1879 (FS15i) Movement direction

2022 (FS30i, 16i)
- 314 -
(a) When the coil slider is movable:

+111: When the positive direction is specified, the slider moves
in the positive direction.
-111: When the positive direction is specified, the slider moves
in the reverse direction.
Power line Positive
direction
Slider movable
Magnet plate fixed
(b) When the magnet plate is movable:

+111: When the positive direction is specified, the magnet plate
moves in the positive direction.
-111: When the positive direction is specified, the magnet plate
moves in the reverse direction.
Power line
Positive Slider fixed

direction
Magnet plate movable
Motor ID number

2020 (FS30i, 16i)
Standard parameters are prepared for the linear motors listed below as
of July, 2007. When the standard parameters are not included in the
servo software used, see the parameter list shown in this manual, and
set the parameters.
[200-V driving]
Motor 90B6 90D0
Motor model Motor ID No. 90B1
specification 90B5 90E0
LiS300A1/4 0441-B200 351 B(02) B(02) G(07)
LiS600A1/4 0442-B200 353 B(02) B(02) G(07)
LiS900A1/4 0443-B200 355 B(02) B(02) G(07)
LiS1500B1/4 0444-B210 357 B(02) B(02) G(07)
LiS3000B2/2 0445-B110 360 B(02) B(02) G(07)
LiS3000B2/4 0445-B210 362 B(02) B(02) G(07)
LiS4500B2/2 0446-B110 364 B(02) B(02) G(07)
LiS6000B2/2 0447-B110 368 B(02) B(02) G(07)
LiS6000B2/4 0447-B210 370 B(02) B(02) G(07)
LiS7500B2/2 0448-B110 372 B(02) B(02) G(07)
LiS7500B2/4 0448-B210 374 B(02) B(02) G(07)
LiS9000B2/2 0449-B110 376 B(02) B(02) G(07)
LiS9000B2/4 0449-B210 378 B(02) B(02) G(07)
- 315 -
Motor 90B6 90D0

LiS3300C1/2 0451-B110 380 B(02) B(02) G(07)
LiS9000C2/2 0454-B110 384 B(02) B(02) G(07)
LiS11000C2/2 0455-B110 388 B(02) B(02) G(07)
LiS15000C2/2 0456-B110 392 B(02) B(02) G(07)
LiS15000C2/3 0456-B210 394 B(02) B(02) G(07)
LiS10000C3/2 0457-B110 396 B(02) B(02) G(07)
LiS17000C3/3 0459-B110 400 B(02) B(02) G(07)
The motor ID numbers are for SERVO HRV2. Loading is possible

with the servo software of the series and edition listed above or
subsequent editions.
[400-V driving]
Motor 90B6 90D0
LiS1500B1/4 0444-B210 358 B(02) B(02) G(07)
LiS3000B2/2 0445-B110 361 B(02) B(02) G(07)
LiS4500B2/2HV 0446-B010 363 B(02) B(02) G(07)
LiS4500B2/2 0446-B110 365 B(02) B(02) G(07)
LiS6000B2/2HV 0447-B010 367 B(02) B(02) G(07)
LiS6000B2/2 0447-B110 369 B(02) B(02) G(07)
LiS7500B2/HV2 0448-B010 371 B(02) B(02) G(07)
LiS7500B2/2 0448-B110 373 B(02) B(02) G(07)
LiS9000B2/2 0449-B110 377 B(02) B(02) G(07)
LiS3300C1/2 0451-B110 381 B(02) B(02) G(07)
LiS9000C2/2 0454-B110 385 B(02) B(02) G(07)
LiS11000C2/2HV 0455-B010 387 B(02) B(02) G(07)
LiS11000C2/2 0455-B110 389 B(02) B(02) G(07)
LiS15000C2/3HV 0456-B010 391 B(02) B(02) G(07)
LiS10000C3/2 0457-B110 397 B(02) B(02) G(07)
LiS17000C3/2 0459-B110 401 B(02) B(02) G(07)

NOTE
For the motor ID number of the conventional
models, see Appendix G.
After parameter initialization, check that the function bit for linear
motor control is set to 1 (linear motor control is enabled).
#7 #6 #5 #4 #3 #2 #1 #0
1954(FS15i) LINEAR
2010(FS30i,16i)
LINEAR(#2) Linear motor control is:
0: Disabled
1: Enabled
- 316 -
When using position detection circuit H or C for linear motor

For incremental type
When a position detection circuit having an interpolation
magnification of 2048 is used with an incremental type linear encoder,
the parameter shown below must be set to maintain both the maximum
feedrate and high resolution. Set the parameter before proceeding to
procedure (2).

(Series 0i-C, 20i-B)
To use a linear motor position detection circuit (A860-2033-T20*,

-T30*), the servo software of the following series and editions is need:
#7 #6 #5 #4 #3 #2 #1 #0
2687(FS15i) HP2048
2274(FS30i,16i)
HP2048(#0) A circuit having an interpolation magnification of 2048 (position
detection circuit H or C for linear motor) is:
0: Not used
1: Used
NOTE
1 Setting this parameter(No.2274(FS30i,16i) or
No.2687(FS15i)) to "enable" lets you make the
basic parameter settings as explained in Procedure
(2).
2 Changing this parameter results in a power-off
alarm being raised.
3 When this parameter is set, the detection unit in the
case of FFG=1/1 is (signal pitch/512 [um]).
If a minimum detection unit (signal pitch/2048 [µm])
is necessary, specify:
FFG = 4/1
- 317 -
NOTE
4 If nano-interpolation is applied, a resolution as high
as (signal pitch/2048 [µm]) is applied as
decimal-part feedback.
5 When a linear encoder of incremental type is used,
a linear motor pole detector is needed.
6 With position detection circuit H for linear motor,
the interpolation magnification can be changed
using setting pin SW3. (The setting at the time of
shipment is Setting B.)
Setting A: The interpolation magnification is 512.
Setting B: The interpolation magnification is 2048.
Setting A enables up to high-speed operation, and
Setting B enables high resolution feedback
acquisition.
Setting A Setting B
HP2048 1 1
Resolution [µm] ※1 λ [µm]/128 *2 λ [µm]/ 512 *2
Maximum velocity
λ [µm] × 122880 *2 λ [µm] × 30720 *2
[mm/min]
(*1) The resolution values in the table above are

used for calculation of various parameters.
(*2) λ [mm] represents a linear scale signal pitch.
7 When the position detection circuit C for linear
motor is used, no function is available which can
change an interpolation magnification according to
a set-up pin. (Fixed at a magnification of 2048)
Linear motor position detection circuit C is
connected to the scale with an absolute address
origin.
- 318 -

Procedure (2) makes parameter settings that depend on the resolution
of the linear encoder (hereafter simply called "the resolution"). Set the
parameters according to Table 4.14.1 (d), (e).
When using an incremental type linear encoder, calculate as follows:

Resolution [µm] = encoder signal pitch [µm] / 512
The pole-to-pole span used in calculation varies, depending on the

motor model.
• Small linear motors: 30 mm (LiS300A, LiS600A, LiS900A)
• Medium-size and large linear motors: 60 mm (models other than
the above)
(See Table 4.14.1(c).)
#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) PLC0
2000 (FS30i, 16i)
PLC0(#0) The number of velocity pulses and the number of position pulses are:
0: Used without being modified.
1: Used after being multiplied by 10
If the number of velocity pulses is lager than 32767, set the parameter
to 1.
If the number of position pulses exceeds 32767, use the following
position pulse conversion coefficient.
1876 (FS15i) Number of velocity pulses

2023 (FS30i, 16i)
(Parameter calculation expression)
Number of velocity pulses = 3125 / 16 / (resolution [µm])
If the calculation result is greater than 32767, set up PLC0 = 1, and set
the parameter (PULCO) with a value of 1/10.
1891 (FS15i) Number of position pulses

2024 (FS30i, 16i)
Number of position pulses = 625 / (resolution [µm])
If the calculation result is greater than 32767, determine the parameter
setting (PPLS), using the following position pulse conversion
coefficient (PSMPYL).
- 319 -
2628 (FS15i) Position pulses conversion coefficient

2185 (FS30i, 16i)
This parameter is used if the calculated number of position pulses is
greater than 32767.
(It can be specified in the Series 90B0, 90B1, 90B6, 90B5, 90D0, or
90E0.)
PLC0 = 0 → The parameter is set so that the following equation
holds: (the number of position pulses) × (position
pulses conversion coefficient) = 625/resolution [µm].
PLC0 = 1 → The parameter is set so that the following equation
holds: 10 × (the number of position pulses) × (position
pulses conversion coefficient) = 625/resolution [µm].
(→ See Supplementary 3 of Subsection 2.1.8.)
#7 #6 #5 #4 #3 #2 #1 #0
1707 (FS15i) APTG
2013 (FS30i, 16i)
APTG(#7) When using an absolute type linear encoder, set this bit to:
1: Ignores an α Pulsecoder soft disconnection.
Setting AMR conversion coefficients
Calculate the number of feedback pulses per pole-to-pole span of the
linear motor, and find AMR conversion coefficients 1 and 2 expressed
by the equation shown below.
Number of pulses per pole-to-pole span
= pole-to-pole span [mm] × 1000/resolution [µm]
= (AMR conversion coefficient 1) × 2(AMR conversion coefficient 2)

2112 (FS30i, 16i)

2138 (FS30i, 16i)
Supplementary)
If AMR conversion coefficient 1 = (pole-to-pole span [mm]/
resolution [µm]) is an integer and a multiple of 1024, setting of
only AMR conversion coefficient 1 is needed. In this case, the
following are assumed:
AMR conversion coefficient 1
= (pole-to-pole span [mm]/resolution [µm])
AMR conversion coefficient 2 = 0
The pole-to-pole span depends on the motor model as indicated in the
table below.
Table 4.14.1 (c) List of pole-to-pole spans
Classification Pole-to-pole span (D) Motor model
Small motors 30mm LiS300A, LiS600A, LiS900A
Medium-size and
60mm Model other than the above
large motors
- 320 -
1977 (FS15i) Flexible feed gear numerator

2084 (FS30i, 16i)
1978 (FS15i) Flexible feed gear denominator

2085 (FS30i, 16i)
Use a unified detection unit for the flexible feed gear (FFG)
parameters according to Tables 4.14.1 (d) and 4.14.1 (e).
FFG = (resolution [µm]) / (detection unit [µm])
Table 4.14.1 (d) Parameter setting when an incremental type linear encoder is used
[Medium-size and large motors] (pole-to-pole span: 60mm)
Number of velocity pulses / FFG(No.2084/No.2085)
AMR conversion
PLC0 Number of position pulses,
Signal pitch coefficient 1 or 2 0.1-µm
(2000#0) Conversion coefficient 1-µm detection
(No.2112, 2138) detection
(No.2023 / No.2024, 2185)
20 0 5000 / 16000, 0 3000, 9 5 / 128 50 / 128
40 0 2500 / 8000, 0 1500, 9 5 / 64 50 / 64
2 1 5000 / 8000, 2 30000, 9 1 / 256 10 / 256
4 1 2500 / 8000, 0 15000, 9 1 / 128 10 / 128
40.513167 0 2468 / 7899, 0 1481, 9 301 / 3804 3010 / 3804
[Small motors] (pole-to-pole span: 30mm)
AMR conversion
Signal pitch coefficient 1 or 2 0.1-µm
(No.2023 / No.2024, 2185)
20 0 5000 / 16000, 0 1500, 9 5 / 128 50 / 128
40 0 2500 / 8000, 0 750, 9 5 / 64 50 / 64
2 1 5000 / 8000, 2 15000, 9 1 / 256 10 / 256
4 1 2500 / 8000, 0 7500, 9 1 / 128 10 / 128
40.513167 0 2468 / 7899, 0 1481, 8 301 / 3804 3010 / 3804
* The parameter Nos. for the Series 15i are omitted. See the
previous page.
Table 4.14.1 (e) Parameter setting when an absolute type linear encoder is used
[Medium-size and large motors] (pole-to-pole span: 60mm)
AMR conversion
Resolution coefficient 1 or 2 0.1-µm
(No.2023 / No.2024, 2185)
0.1 0 1953 / 6250, 0 9375, 6 1/10 1/1
0.05 0 3906 / 12500, 0 9375, 7 1/20 1/2
[Small motors] (pole-to-pole span: 30mm)
AMR conversion
Resolution coefficient 1 or 2 0.1-µm
(No.2023 / No.2024, 2185)
0.1 0 1953 / 6250, 0 9375, 5 1/10 1/1
0.05 0 3906 / 12500, 0 9375, 6 1/20 1/2
* The parameter Nos. for the Series 15i are omitted. See the
previous page.
- 321 -
(Cautions)
If the encoder signal pitch is larger than 200 µm, various coefficients
used in the servo software may overflow to raise an alarm on invalid
parameters, because the setting for the number of velocity pulses
becomes very small.
In this case, change the corresponding parameter by referencing
Subsection 2.1.8, "Measures for Alarms on Illegal Servo Parameter
Settings."
When a linear motor is used, the linear encoder must be installed so

that the Z phase of the linear encoder matches the origin of the
activating phase. Otherwise, the specified motor characteristics cannot
be obtained. (For details of installation positions, refer to "FANUC
LINEAR MOTOR LiS series DESCRIPTIONS (B-65382EN)".)
Procedure (3) describes the method of adjusting the activating phase

origin (AMR offset adjustment) when it is difficult to install a linear
encoder at a specified position with a specified precision.
Setting the AMR offset

• When the learning control function is used (Series 90B3 and
90B7), see "Learning Function Operator's Manual".
• When the learning control function is not used (Series 9096,
90B0, 90B6, 90B5, 90D0, and 90E0), set the AMR offset as
follows:
1762 (FS15i) AMR offset

2139 (FS30i, 16i)
Specifies an activating phase (AMR offset) for phase Z.
[Unit of data] Degrees
[Valid data range] -45 to +45 (*)
(*) Extended AMR offset setting range (-60 degrees to +60 degrees)
can be specified by setting the parameter below. So, if the AMR
offset value does not lie within the range -45 degrees to +45
degrees in adjustment processing, set the bit below. (Usually, set
the bit below to 0.)
(Series 9096 and Series 90B0/B(02) and earlier editions are not
supported.)
#7 #6 #5 #4 #3 #2 #1 #0
2683 (FS15i) AMR60
2270 (FS30i, 16i)
AMR60 (#0) Changes the AMR offset setting range.
0: -45 degrees to +45 degrees (standard setting range)
1: -60 degrees to +60 degrees (extended setting range)
- 322 -
The procedure for AMR offset adjustment is described below. The

procedure varies according to whether an incremental type linear
encoder or absolute type linear enable is used. Before starting an
adjustment, check the type of linear encoder used.
CAUTION
Note that if an incorrect AMR offset value is input,
the thrust of the motor can decrease or the motor
can make an unpredictable motion.
After setting a correct AMR offset value, never
rewrite the set value manually.
Incremental type
The procedure for AMR offset adjustment when an incremental type
linear encoder is used is described below. When using an absolute
type linear encoder, see the item of Absolute type described later.
Make a fine activating phase adjustment according to the procedure

below.
NOTE
The method of AMR offset adjustment using
SERVO GUIDE is described below. For the method
using the servo check board, see Appendix I.3.
Measuring the activating phase

(1) Connect SERVO GUIDE to the CNC, and set channel data as
shown below.
Select the target axis for measurement, and set the data type to
"ROTOR".
* For a linear motor, a value from 0 to 360 degrees is read

each time a motion is made over the distance of a pair of the
N pole and S pole of the magnet (pole-to-pole span).
- 323 -
(2) Run the linear motor using a JOG operation for example, and
observe the behavior of the activating phase (AMR) before, at
the moment, and after phase Z is captured. (See Figs. 4.14.1 (a)
and (b).)
The activating phase changes to 0 (or 360) degrees at the moment
phase Z is captured. Measure the value just before it changes,
and let this value be A.
360° 360°
45° or lower (*) 315° or higher (*)
Phase Z Phase Z
Fig. 4.14.1 (a) If the offset is set with a positive number Fig. 4.14.1 (b) If the offset is set with a negative number
(before AMR offset adjustment) (before AMR offset adjustment)
(*) The figures above provide examples where AMR60=0. When

AMR60=1, the values should read 60° or lower and 60° or
higher.
(3) Set the AMR offset parameter with A (or A - 360).

* The parameter setting range is:
-45 degrees to +45 degrees (when AMR60 = 0)
When the value of A does not lie within the setting range, the
installation position of the linear encoder needs to be readjusted.
(4) Switch the power off and on again. Now parameter setting is
completed.
(5) Observe the activating phase (AMR) again according to step (2)
above, and check that the activating phase changes continuously
in the phase Z rising portion.
(6) Switch the power off and on again. This completes parameter
setting.
- 324 -
45° or lower (*) 315° or lower (*)

360° 360°
Phase Z Phase Z
Fig. 4.14.1(c) If the offset is set with a positive Fig. 4.14.1(d) If the offset is set with a negative
number (after AMR offset adjustment) number (after AMR offset adjustment)
(*) The figures above provide examples where AMR60=0. When

AMR60=1, the values should read 60° or lower and 300° or
higher.
Absolute type
The procedure for AMR offset adjustment when an absolute type
linear encoder is used is described below. When using an incremental
type linear encoder, see the item of Incremental type described earlier.
below.
CAUTION
In this adjustment, the linear motor is driven by
current fed from the DC power supply. So, the CNC
does not exercise position control. For safety,
move the coil slider of the linear motor to near the
stroke center and make an adjustment. (Activation
by the DC power supply moves a medium-size or
large linear motor for up to about 60 mm, and
moves a small linear motor for up to about 30 mm.)
(1) For phase data measurement, set the following parameters:

Series of servo Phase data
Parameter setting Unit of data
software display screen
Series 9096 No. 2115=320 (odd-numbered axis), 960 (odd-numbered axis) Diagnosis No. 256/electrical
No. 2115=0 (odd-numbered axis, even-numbered axis) 353 angle
Series 90B0 • Other than the Series 15i
Series 90B1 No. 2115=320 (odd-numbered axis), 2368 (odd-numbered axis)
Series 90B5 No. 2115=0 (odd-numbered axis, even-numbered axis)
Series 90B6 • Series 15i Arbitrary data
No. 1726=320 (odd-numbered axis), 2368 (odd-numbered axis) screen
No. 1774=0 (odd-numbered axis, even-numbered axis) (described later)
Series 90D0 None Diagnosis No.
Series 90E0 762
* The selection of an odd-numbered axis or even-numbered axis in the figure above depends on whether
the setting of No. 1023 (servo axis number) is an odd number or even number.
- 325 -
When the setting above is made, phase data is output to the display
screen indicated above. The display data (phase data) equal to 256 on
the diagnosis screen corresponds to an activating phase of 360 degrees.
This means that a displayed phase data value is converted to an
activating phase [degrees] according to the following expression:
Activating phase [degrees] = Displayed phase data value ×
360/256
(2) Turn off the power to the CNC and servo amplifier.
(3) Detach the linear motor power line from the servo amplifier, then
connect the power line to the DC power supply.
Connect the + terminal of the DC power supply to phase U of the
power line, and connect the - terminal of the DC power supply to
phase V and phase W of the power line.
DC power
l
Coil slider
+ -
W
Fig. 4.14.1(e) Connection of DC power supply
(4) In the emergency stop state, turn on the power to the CNC and
servo amplifier.
(5) Display phase data on the diagnosis screen of the CNC then turn
on the DC power supply. Next, increase the current gradually
(DC activation).
When the force of the linear motor produced by current supplied
from the DC power supply exceeds static friction, the linear
motor starts moving, and the linear motor automatically stops at a
position where activation phase = 0.
A position where activating phase = 0 is present at intervals of 60
mm with medium-size and large linear motors, or at intervals of
30 mm with small linear motors.
WARNING
If a large current flows abruptly, the motor
produces a large force, resulting in a very
dangerous situation. When making this adjustment,
be sure to increase the current value gradually
starting from current value = 0 [Ap].
- 326 -
(6) Read the value of phase data on the CNC screen in the state
where the linear motor rests. Immediately after reading the value,
turn off the DC power supply.
* Change the DC excitation start position within one pole (60
mm for the medium-sized/large type or 30 mm for the small
type) then make measurements of (5) or (6). Repeat this
procedure several times to determine average phase data.
(7) Based on activating phase data measured with up to step 6)

above, set the AMR offset parameter as described below.
* In the description below, the parenthesized values assume
AMR60 = 1.
When 0 ≤ phase data ≤ 32 (42)

AMR offset setting = −1 × phase data value × 360/256
When 224 (214) ≤ phase data ≤ 255 (255)
AMR offset setting = 360 − phase data value × 360/256
When 32 (42) < phase data < 224 (214)
In this case, a soft phase alarm is issued when phase Z is
passed. Adjust the linear encoder installation position
according to "FANUC LINEAR MOTOR Lis series
DESCRIPTIONS (B-65382EN)". After adjustment, make
an AMR offset adjustment again from step 1).
(8) Turn off then turn on the power to the CNC.
(9) Perform steps (5) and (6) again, and check that the activating
phase data at a stop position is about 0 or 255.
(10) Turn off the power to the CNC and servo amplifier. Next,
connect the power line of the linear motor to the servo amplifier.
Then, turn on the power to the CNC and servo amplifier again.
(11) Decrease the torque limit and excessive error alarm level and use
jog feed to check that feed operation is normal. When feed
operation is normal, return the value of the parameter set in (1) to
0 and return the torque limit and excessive error alarm level to
the original values. This completes the setting.
- 327 -
The activating phase can also be observed by connecting SERVO

GUIDE to the CNC and selecting "Monitor" from the
"Communication" menu of the graph window.
(Set "ROTOR" as the data type in channel setting.)
(Supplement)
Method for checking the activating phase value in the Series 15i
The diagnosis screen of the Series 15i has no data that
corresponds to No. 353 on the diagnosis screen of the Series 16i
and so on. So, display an arbitrary data screen by making the
following parameter setting to check the activating phase value.
#7 #6 #5 #4 #3 #2 #1 #0
2208 (FS15i) ARB
-
ARB (#3) The arbitrary data screen is:
0: Not displayed
1: Displayed ← Use this setting.
Settings on the arbitrary data screen (see Fig. 4.14.1 (f).)
Parameter 1 of data 1 is loaded with the value set in Procedure (1).
Make sure that parameter 2 is 0.
The activating phase is displayed in an enclosed section in the figure.
Fig. 4.14.1 (f) Series 15i arbitrary data screen
- 328 -
Procedure (4) explains how to set up parameters for using a linear

scale with a distance-coded reference marks in linear motor position
detection circuit C (A860-0333-T301, -T302 or A860-2033-T301,
-T302).
• This function is optional.

• This function is supported only for the Series 30i/31i/32i-A,
15i-MB, 16i/18i/21i-B as of December 2005.
• For details of parameter setting, refer to the relevant CNC
manual or specifications.
(For Series 30i/31i/32i-A)

Refer to the CNC connection manual (B-63943EN).
All software series and editions are applicable.
(For Series 15i-MB)
Refer to the CNC specifications (A-79233E).
All software series and editions are applicable.
(For Series 16i/18i/21i-B)
Refer to the CNC specifications (A-78754EN).
Series and editions of applicable CNC software
B0H1/BDH1/DDH1-17 and subsequent editions (Series
16i/18i/21i-MB)
B1H1/BEH1/DEH1-17 and subsequent editions (Series
16i/18i/21i-TB)
BDH5-07 and subsequent editions (Series 18i-MB5)
Setting procedure (for the Series 15i-MB)

Refer to the CNC specifications (A-79233E).
Setting procedure (for the Series 30i/31i/32i-A, Series 16i/18i/21i-B)

(1) Enable the linear scale with a distance-coded reference marks.
#7 #6 #5 #4 #3 #2 #1 #0
- DCLx
1815 (FS30i, 16i)
DCLx (#2) The linear scale interface with absolute address referenced mark is:
0: Not used as a position detector
1: Used as a position detector ← To be set
#7 #6 #5 #4 #3 #2 #1 #0
- SDCx
1818 (FS30i, 16i)
SDCx (#3) The linear scale with a distance-coded reference marks is:
0: Not used
1: Used ← To be set
- 329 -
- Reference counter capacity

1821 (FS30i, 16i)
Specify a round figure, such as 10000 or 50000, as the reference
counter capacity.
- Coordinate of the first reference position in the machine coordinate system

for each axis
1240 (FS30i, 16i)
Specify 0.
- Distance 1 from the scale mark origin to the reference position

1883 (FS30i, 16i)
Specify 0.
- Distance 2 from the scale mark origin to the reference position

1884 (FS30i, 16i)
Specify 0.
(2) Turn the CNC power off and on again.
(3) Follow this procedure to establish a reference position at an

appropriate point.
Select the JOG mode, and set the manual reference position
return signal ZRN to "1".
Set a feed axis direction selection signal (+J1, -J1, +J2, -J2, ...)
for an axis for which a reference position is to be established to
"1" and issue the signal.
When an absolute position on the linear scale is detected, the axis
stops, causing the reference position-established signal (ZRF1,
ZRF2, ...) to be set to "1".
If an overtravel alarm is issued in establishing a reference
position, try to establish a reference position by disabling a
stored stroke check.
(4) In the JOG or handle feed mode, place the machine accurately on
the reference position.
(5) Using the following steps, perform the automatic setting of

parameter No. 1883.
#7 #6 #5 #4 #3 #2 #1 #0
- DAT
1819(FS30i, 16i)
DAT (#2) At a manual reference position return, the automatic setting of
parameter No. 1883 is:
0: Not performed
1: Performed ← To be set
After setting this parameter to "1", perform a manual reference
position return.
When the manual reference position return is completed, parameter
No. 1883 is specified, and this parameter is automatically reset to "0".
- 330 -
(6) If you want to disable a stored stroke check in establishing a

reference position, re-set the necessary parameters to the original
setting.
(7) Specify parameter No. 1240 as required.
- Coordinate of the first reference position in the machine coordinate system

for each axis
1240 (FS30i, 16i)
Set up the coordinate of the first reference position in the machine
coordinate system.
(8) This is the end of setting.
Procedure (5) can be used to set parameters according to the cooling

method used for linear motors.
Change the following parameters as listed in Table 4.14.1 (f). For
self-cooling linear motors, the parameters need not be set here,
because they are set up at initialization in procedure (1).
1877 (FS15i) OVC alarm parameter (POVC1)

2062 (FS30i, 16i)

2063 (FS30i, 16i)
1893 (FS15i) OVC alarm parameter (POVCLMT)

2065 (FS30i, 16i)
1979 (FS15i) Current rating parameter (RTCURR)

2086 (FS30i, 16i)
1784 (FS15i) OVC magnification in stop state (OVCSTP)

2161 (FS30i, 16i)
CAUTION
If the correct values corresponding to the cooling
method are not set in the parameters above,
expected thermal protection cannot be provided.
Use care.
- 331 -
Table4.14.1 (f) Setting OVC and current rating parameters by cooling method
[200V driving]
Model Cooling method Rated (N) POVC1 POVC2 POVCLMT RTCURR OVCSTP
No cooling 50 32720 596 589 564 0
LiS300A1/4
Water cooling 100 32578 2380 2357 1129 0
No cooling 100 32720 596 589 564 0
LiS600A1/4
Water cooling 200 32578 2380 2357 1129 0
No cooling 150 32721 583 1326 847 0
LiS900A1/4
Water cooling 300 32582 2328 5303 1694 0
No cooling 300 32698 873 2590 1184 0
LiS1500B1/4
Water cooling 600 32490 3481 10358 2368 0
No cooling 600 32711 719 2131 1074 0
LiS3000B2/2
Water cooling 1200 32539 2867 8523 2148 0
No cooling 600 32698 873 2590 1184 0
LiS3000B2/4
Water cooling 1200 32490 3481 10358 2368 0
No cooling 900 32707 758 1199 805 0
LiS4500B2/2
Water cooling 1800 32526 3023 4794 1611 0
No cooling 1200 32711 719 2131 1074 0
LiS6000B2/2
Water cooling 2400 32539 2867 8523 2148 0
No cooling 1200 32698 873 2590 1184 0
LiS6000B2/4
Water cooling 2400 32528 3003 8932 2368 140
No cooling 1500 32707 765 832 671 0
LiS7500B2/2
Water cooling 3000 32524 3053 3329 1342 0
No cooling 1500 32687 1010 799 658 0
LiS7500B2/4
Water cooling 3000 32446 4026 3197 1316 0
No cooling 1800 32707 758 1199 805 0
LiS9000B2/2
Water cooling 3600 32526 3023 4794 1611 0
No cooling 1800 32696 895 1151 789 0
LiS9000B2/4
Water cooling 3600 32482 3570 4604 1579 0
No cooling 660 32708 749 1184 801 0
LiS3300C1/2
Water cooling 1320 32529 2987 4738 1602 0
No cooling 1800 32729 489 1112 776 0
LiS9000C2/2
Water cooling 3600 32612 1953 4448 1552 0
No cooling 2200 32723 560 1661 948 0
LiS11000C2/2
Water cooling 4400 32589 2236 6644 1897 0
No cooling 3000 32729 483 621 579 0
LiS15000C2/2
Water cooling 7000 32558 2623 3378 1352 0
No cooling 3000 32732 452 1340 852 0
LiS15000C2/3
Water cooling 7000 32572 2455 7296 1988 140
No cooling 2000 32722 580 1719 964 0
LiS10000C3/2
Water cooling 4000 32583 2314 6875 1929 0
No cooling 3400 32711 709 981 729 0
LiS17000C3/3
Water cooling 6800 32542 2829 3925 1458 0
- 332 -
[400V driving]
Model Cooling method Rated (N) POVC1 POVC2 POVCLMT RTCURR OVCSTP
No cooling 300 32698 873 2590 1184 0
LiS1500B1/4
Water cooling 600 32490 3481 10358 2368 0
No cooling 600 32711 719 2131 1074 0
LiS3000B2/2i
Water cooling 1200 32539 2867 8523 2148 0
No cooling 900 32714 681 1549 915 0
LiS4500B2/2HV
Water cooling 1800 32551 2718 6194 1831 0
No cooling 900 32707 758 1199 805 0
LiS4500B2/2
Water cooling 1800 32526 3023 4794 1611 0
No cooling 1200 32706 774 688 610 0
LiS6000B2/2HV
Water cooling 2400 32521 3085 2753 1221 0
No cooling 1200 32711 719 2131 1074 0
LiS6000B2/2
Water cooling 2400 32539 2867 8523 2148 0
No cooling 1500 32714 680 1075 763 0
LiS7500B2/HV2
Water cooling 3000 32551 2713 4301 1526 0
No cooling 1500 32709 739 658 596 0
LiS7500B2/2
Water cooling 3000 32532 2949 2631 1193 0
No cooling 1800 32709 737 947 716 0
LiS9000B2/2
Water cooling 3600 32533 2940 3788 1432 140
No cooling 660 32708 749 1184 801 0
LiS3300C1/2
Water cooling 1320 32529 2987 4738 1602 0
No cooling 1800 32728 494 879 689 0
LiS9000C2/2
Water cooling 3600 32610 1972 3514 1379 0
No cooling 2200 32723 560 1661 948 0
LiS11000C2/2HV
Water cooling 4400 32589 2236 6644 1897 0
No cooling 2200 32730 474 1312 843 0
LiS11000C2/2
Water cooling 4400 32616 1894 5250 1686 140
No cooling 3000 32730 471 1396 869 0
LiS15000C2/3HV
Water cooling 7000 32563 2557 7601 2029 140
No cooling 2000 32720 597 1358 857 0
LiS10000C3/2
Water cooling 4000 32577 2384 5432 1715 140
No cooling 3400 32711 709 981 729 0
LiS17000C3/2
Water cooling 6800 32542 2829 3925 1458 0
- 333 -
[Conventional linear motors]

Model Cooling method Rated (N) POVC1 POVC2 POVCLMT RTCURR
No cooling 300 32698 873 2590 1184
1500A/4 Air cooling 360 32667 1257 3729 1421
Water cooling 600 32490 3481 10358 2369
No cooling 600 32698 873 2590 1184
3000B/2 Air cooling 720 32667 1257 3729 1421
Water cooling 1200 32490 3481 10358 2369
No cooling 600 32698 873 2590 1184
3000B/4 Air cooling 720 32667 1257 3729 1421
Water cooling 1200 32490 3481 10358 2368
No cooling 1200 32698 873 2590 1184
6000B/2 Air cooling 1440 32667 1257 3729 1421
Water cooling 2400 32490 3481 10358 2369
No cooling 1200 32706 777 2304 1117
6000B/4
Air cooling 1440 32679 1118 3317 1340
(160A driving)
Water cooling 2400 32520 3098 9215 2234
No cooling 1800 32729 491 1457 888
9000B/2
Air cooling 2160 32711 707 2098 1065
(160A driving)
Water cooling 3600 32611 1962 5827 1776
No cooling 1800 32737 388 1151 789
9000B/4
Air cooling 2160 32723 559 1657 947
(360A driving)
Water cooling 3600 32644 1551 4604 1579
No cooling 3000 32751 209 621 579
15000C/2
Air cooling 3600 32744 301 894 695
(360A driving)
Water cooling 7000 32677 1139 3378 1352
No cooling 3000 32732 452 1340 852
15000C/3 Air cooling 3600 32716 651 1930 1022
Water cooling 7000 32572 2455 7296 1988
- 334 -
(6) Illegal servo parameter setting alarms when linear motors are used
The following illegal servo parameter setting alarms are checked
additionally when linear motors are used (they are not issued for
rotary motors).
Parameter error
Description
alarm detail No.
No separate detector can be used for linear motors. Full-closed loop setting
10043
results in an alarm being issued.
If no AMR conversion coefficient is set, an alarm is issued. Even when the
linear encoder is not relocated after the motor is replaced, the AMR
1123
conversion coefficients must be re-set, because initialization accompanying
motor replacement causes the AMR coefficients to be erased.
The valid AMR offset data range is below :
-45 (degrees) and +45 (degrees) : (AMR60=0)
1393 -60 (degrees) and +60 (degrees) : (AMR60=1)
If a value out of this range is specified in the parameter, an
invalid-parameter alarm is issued.
CAUTION
When an AMR conversion coefficient is not set, an
alarm is issued. If it is set, but incorrect, no alarm is
issued. In this case, the linear motor fails to drive
correctly immediately after it passes phase Z. It
may move within one pole-to-pole span (60 mm or
30 mm) in the worst case.
(7) Notes on using high-speed HRV current control or the cutting /rapid
velocity loop gain switching function
In general, a higher velocity loop gain (load inertia ratio) is set for a
linear motor than for a rotary motor. So, if high-speed HRV current
control and the cutting /rapid velocity loop gain switching function are
used at the same time to achieve an even higher velocity loop gain, an
overflow can occur in the internal value of the post-override velocity
load proportional (PK2V: parameter No. 1856 for Series 15i or No.
2044 for Series 30i, 16i, and so on). (The parameter error detail
number is 443 (*)). In this case, set the parameter indicated below.
Whether an overflow occurs or not can be checked using Fig.
4.14.1(g).
(*)
Series 9096 and Series 90B0/C(03) and earlier editions do not
support the occurrence of parameter errors in velocity gain
override and the display of detail numbers.
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) P2EX
2200 (FS30i, 16i)
P2EX(#6) The format of velocity loop proportional gain (PK2V) is:
0: Standard format.
1: Converted. ← To be set
- 335 -
|PK2V parameter| × (load inertia ratio + 256) × 2000

A= Larger than 32767
(Number of velocity pulses) × 64
larger than 32767?
Not larger than 32767
B = A × (velocity loop gain override [%] (*1) )/100

Larger than 32767
larger than 32767?
Not larger than 32767
Overflow not produced Overflow occurred.

Set the following bits:
Bit 6 of No. 1740 = 1 (Series 15i)
Bit 6 of No. 2200 = 1 (Series 30i, 16i, and so on)
Fig. 4.14.1(g) PK2V overflow check
CAUTION
*1 In the flowchart above, the velocity loop gain
override is represented by one of the following
parameters:
Velocity gain magnification when high-speed HRV
current control is enabled
→ (No. 2335 for Series 30i, 16i, and so on or No.
2748 for Series 15i)
Velocity gain override when the cutting feed/rapid
traverse switchable velocity loop gain function is
enabled
→ (No. 2107 for Series 30i, 16i, and so on or No.
1700 for Series 15i)
- 336 -
4.14.2 Detection of an Overheat Alarm by Servo Software when a

Linear Motor and a Synchronous Built-in Servo Motor are
Used
(1) Overview
When a linear motor or synchronous built-in servo motor is used, the
overheat signal (thermostat signal) of the motor can be connected in
one of three ways:
Configuration 1 : Connected to the PMC signal
Configuration 2 : Connected to the αiCZ detection circuit
(A860-2162-T***) or the linear motor position
detection circuit (A860-2033-T***)
Configuration 3 : Connected to the temperature detection circuit
This subsection describes these methods of connection and setting.
If the overheat signal is connected using a method described in this
subsection and an overheat alarm is issued, quick stop processing
(quick stop function based on a command specifying a velocity of 0)
is also usable. (For details, see Subsection 4.11.6, "Quick Stop
Function at OVC and OVL Alarm".)
In configuration 2 and configuration 3, temperature information can
be observed on the CNC screen by using the temperature information
signal (thermistor signal) built into a linear motor or synchronous
built-in servo motor.
[Configuration 1]
DI of PMC Overheat signal Linear motor or
CNC
(Thermostat signal) synchronous built-in servo motor
[Configuration 2]
αiCZ detection circuit or linear
motor position detection circuit
An overheat signal connection mode

[Configuration 3]
can be selected from three
Separate Temperature configurations.
detector detection circuit
interface unit
CAUTION
When using a linear motor or synchronous built-in
servo motor, be sure to monitor the overheat signal
by using any of the methods mentioned above.
Otherwise, the motor cannot be properly protected
against overheating.
- 337 -
(2) Series and editions of applicable software

Note that the usable software editions depend on the configuration.
Configuration
Series and editions of
(overheat signal Series and editions of system software
servo software
connection)
Configuration 1 (Series 30i,31i,32i) B0H1/BDH1-24 and subsequent editions (Series 16i/18i-MB)
(Connected to the Series 90D0/J(10) and B0K1/BDK1-01 and subsequent editions (Series 16i/18i-MB)
PMC) subsequent editions B1H1/BEH1-24 and subsequent editions (Series 16i/18i-TB)
Series 90D3/A(01) and B1K1/BEK1-01 and subsequent editions (Series 16i/18i-TB)
subsequent editions BDH5-14 and subsequent editions (Series 18i-MB5)
Series 90E0/J(10) and BDK5-01 and subsequent editions (Series 18i-MB5)
subsequent editions DDH1-24 and subsequent editions (Series 21i-MB)*1
Series 90E3/A(01) and DDK1-01 and subsequent editions (Series 21i-MB)*1
subsequent editions DEH1-24 and subsequent editions (Series 21i-TB)*1
(Series 16i-B and so on) DEK1-01 and subsequent editions (Series 21i-TB)*1
Series 90B6/B(02) and D0H1-01 and subsequent editions (Series 20i-FB)*1
subsequent editions D1H1-01 and subsequent editions (Series 20i-TB)*1
Series 90B1/C(03) and D4B1/ D4C1-01 and subsequent editions (Series 0i-MC)*1
subsequent editions D6B1/ D6C1-01 and subsequent editions (Series 0i-TC)*1
Series 90B3/P(16) and
D6D1-01 and subsequent editions (Series 0i-TTC)*1
subsequent editions
Series 90B7/Q(17) and D4A1-07 and subsequent editions (Series 0i-MB)*1
subsequent editions D6A1-07 and subsequent editions (Series 0i-TB)*1
(Series 0i-C, 20i-B) 88E1-03 and subsequent editions (Power Mate i-D)*2
Series 90B5/B(02) and 88E3-01 and subsequent editions (Power Mate i-D)*2
subsequent editions 88F2-10 and subsequent editions (Power Mate i-H)*2
Series 90B8/C(03) and 88F3-01 and subsequent editions (Power Mate i-H)*2
subsequent editions *1 PMC-SB7 required
*2 PMC-SB6 required
*3 This configuration cannot be used with the Series 15i.
*4 The Series 30i supports this configuration, starting with the first
edition.
Configuration 2 (Series 30i,31i,32i) This configuration is usable, regardless of the series and editions
(Connected to the Series 90D0/P(16) and of system software.
αiCZ detection subsequent editions
circuit or Series 90E0/P(16) and
linear motor position subsequent editions
detection circuit) (Series 15i-B,16i-B and so
Configuration 3 on) G002/G012/G022-32.0 and subsequent editions (Series 30i-A)
(Connected to the Series 90B1/K(11) and G003/G013/G023-15.0 and subsequent editions (Series 30i-A)
temperature subsequent editions G121/G131-32.0 and subsequent editions (Series 31i-A5)
detection circuit) (Series 0i-C) G123/G133-15.0 and subsequent editions (Series 31i-A5)
Series 90B8/K(11) and G101/G111-32.0 and subsequent editions (Series 31i-A)
subsequent editions G103/G113-15.0 and subsequent editions (Series 31i-A)
G201-32.0 and subsequent editions (Series 32i-A)
G203-15.0 and subsequent editions (Series 32i-A)
B0K1/BDK1-10 and subsequent editions (Series 16i/18i-MB)
B1H1/BEH1-10 and subsequent editions (Series 16i/18i-TB)
BDK5-10 and subsequent editions (Series 18i-MB5)
DDK1-10 and subsequent editions (Series 21i-MB)
DEK1-10 and subsequent editions (Series 21i-TB)
- 338 -

#7 #6 #5 #4 #3 #2 #1 #0
2713(FS15i) CKLNOH THRMO
2300(FS30i,16i)
THRMO(#3) When bit 7 of No. 2300 is set to 1, the overheat alarm of a motor is:
0: Obtained from a DI signal via the PMC.
1: Obtained from the αiCZ detection circuit, linear motor position
detection circuit, or temperature detection circuit.
* When this parameter has been set, the power must be turned off
CLKNOH(#7) The overheat alarm of a synchronous built-in servo motor or linear
motor is:
0: Obtained from the pulse coder (for an αi/βi motor)
1: Obtained from a DI signal via the PMC, or from the αiCZ
detection circuit, linear motor position detection circuit, or
temperature detection circuit.
* When this parameter has been set, the power must be turned off
Set these parameters according to the overheat signal connection mode

(configuration) as indicated in the table below.
CKLNOH THRMO Description

Detects an overheat alarm with a DI signal via the PMC.
1 0
(Configuration 1)
Detects an overheat alarm via the αiCZ detection circuit
or linear motor position detection circuit.
1 1 (Configuration 2)
Detects an overheat alarm via the temperature
detection circuit.
(Configuration 3)(*1)
(*1) Before an overheat alarm can be detected via the temperature
detection circuit (configuration 3), the temperature detection
circuit must be set (with a parameter such as No. 2278). (See
Subsection 2.1.7.)
NOTE
If bits 3, 7 of No. 2300 are set to 1, 1 (to enable
overheat alarm detection with the built-in
temperature detection circuit) when an αiCZ sensor
of old type (A860-2142-Txxx) not supporting the
temperature detection circuit is used, an illegal
parameter setting alarm (detail number 3002) is
issued.
- 339 -
CAUTION
This function bit is included in the motor standard
parameters. It is set automatically when servo
parameter initialization is performed with a motor
ID number set.
In the CNC that cannot use interface G326 of the
PMC, if this function bit is set to 1, a servo alarm
(motor overheat) is issued. If this occurs, set the
function bit to 0.
(4) Signals (only in configuration 1)

When using configuration 1, connect the overheat signal from the
motor to the following G signal with ladder circuitry:
Overheat state signals via the PMC: SVDI61-SVDI68<Gn326>

#7 #6 #5 #4 #3 #2 #1 #0
Gn326 SVDI68 SVDI67 SVDI66 SVDI65 SVDI64 SVDI63 SVDI62 SVDI61

[Function] Thermostat signals are input via the PMC. An independent signal is
provided for each axis, and the last digit of each name indicates the
number of a controlled axis.
[Status] 0: A signal for issuing an overheat alarm or detecting an overheat is
not connected.
1: No overheat alarm is issued.
(5) Connection and usage

<1> Parameter setting
Set parameter No. 2300 (Series 16i, etc.)/No. 2713 (Series 15i)
according the overheat signal connection mode.
By default, CKLNOH=1 and THRMO=0 are set for a linear
motor and synchronous built-in servo motor (to obtain the
overheat signal via the PMC). If the setting of a parameter does
not match the actual overheat signal connection, the motor
overheat alarm is issued.
<2> Overheat signal connection

Connect the overheat signal to a proper point according to each
configuration. When configuration 1 (connection via the PMC) is
used, a ladder program for connecting the overheat signal
(external signal) to the G signal needs to be created. (No ladder
program is needed for configuration 2 and configuration 3.)
[Alarm detail indication on the servo adjustment screen]

Alarm 1 Alarm 2 Alarm 2
Alarm
#7(OVL) #7(ALD) #4(EXP)
Motor overheat alarm via Pulsecoder 1 1 0
Overheat alarm via PMC DI signal 1 1 1
- 340 -
4.14.3 Smoothing Compensation for Linear Motor
(1) Overview
Smoothing compensation for linear motors improves the smoothness
in feed of a linear motor by producing a sinusoidal compensation
torque with a cycle of 1/2, 1/4, or 1/6 of the pole-to-pole span
produced by servo software and by applying such a torque to the
current command. Compensation torque can be generated for each
motor by setting gain and phase for each component.
Torque command for correction

A2 Sin (2θ + P2) Activating phase angle θ
+ A4 Sin (4θ + P4)
+ A6 Sin (6θ + P6)
+
+
Velocity loop Current loop
TCMD
Scale
Linear motor

(Series 20i-B)
1753 (FS15i) Smoothing compensation performed twice per pole pair

2130 (FS30i, 16i) Correction gain (high-order 8 bits) Correction phase (low-order 8 bits)
1754 (FS15i) Smoothing compensation performed four times per pole pair
1755 (FS15i) Smoothing compensation performed six times per pole pair
- 341 -
Setting the correction gain of the following parameters with a nonzero

value can switch between the negative direction smoothing
compensation and the positive direction smoothing compensation. In
this case, the smoothing compensation parameter explained above
applies only to feeding in the positive direction.
(Series 9096 and Series 90B0/M(13) and earlier editions are not
supported.)
2782 (FS15i) Smoothing compensation performed twice per pole pair (negative direction)
2783 (FS15i) Smoothing compensation performed four times per pole pair (negative direction)
2784 (FS15i) Smoothing compensation performed six times per pole pair (negative direction)
Since the compensation parameters differ from motor to motor

(depending on the motor rather than the model), these parameters must
be determined for each motor assembled.
In principle, variation in torque command that is generated when the
motor is fed at a low speed depends on the position. The application of
smoothing compensation cancels this position-dependent
characteristic, allowing the motor to move smoothly.
The measuring instruments that can be used to determine these
parameters include "SERVO GUIDE" (Ver. 2.00 or later) and servo
tuning software, "SD."
NOTE
The method of adjustment using SERVO GUIDE is
described below. For the method that uses the
servo tuning software "SD", see Appendix I.4.
By using SERVO GUIDE (Ver. 2.00 or later), these parameters can be

determined easily. Follow the procedure below to measure the
activating phase and torque command, which are required to
determine the compensation parameters.
- 342 -
<1> Set channels as follows:

Channel 1: Activating phase
Select the target axis for measurement, and set "ROTOR" as the
data type.
Channel 2: Torque command

Select the target axis for measurement, and set "TCMD" as the
data type.
As the conversion coefficient, set the maximum current of the
amplifier used for the target axis.
<2> Create a program that performs back and forth motion at a

feedrate of F1200 (mm/min).
If the distance of movement is shorter than the pole-to-pole span,
it is impossible to automatically calculate smoothing
compensation parameters. Therefore, it is recommended that the
distance of movement be at least 200 mm for large linear motors
or at least 100 mm for small linear motors. For the number of
measurement points, provide an enough time to obtain data
during one back and forth motion of the motor. (About 15000 to
20000 points in 1-ms sampling)
<3> When making measurements, lower the velocity gain to such an
extent that hunting does not occur.
<4> From the "Tools" menu, select "Linear motor compensation
calculation".
(The shortcut is [Ctrl] + [L].)
- 343 -
<5> In the displayed dialog box, press the [Add] button. Then
waveform data is analyzed, and candidates of the compensation
parameters are registered.
<6> The compensation parameters slightly vary depending on the

measurement situation. So, repeat a data measurement and a
press of the [Add] button several times in a similar manner while
keeping the dialog box open. (Up to five candidates can be
registered.)
If the displayed values include an extremely different value,
uncheck the corresponding check box on the leftmost side of the
list so that the value is not taken into account in the final
compensation calculation.
<7> Finally, press the [Calc] button for each of the forward and
backward directions. Then, smoothing compensation parameters
are displayed.
<8> When the target axis for parameter transfer is selected in
"Parameter change", and the [Set param.] button is pressed, the
presented parameters are set in the CNC.
<9> Measure TCMD again to confirm the effect of smoothing
compensation.
- 344 -
(Adjustment example)
Before smoothing compensation adjustment After smoothing compensation adjustment

Torque command
(TCMD)
(*) For details on the use of SERVO GUIDE, refer to the online help
of SERVO GUIDE.
- 345 -
4.15 SYNCHRONOUS BUILT-IN SERVO MOTOR PARAMETER

SETTING
4.15.1 Procedure for Setting the Initial Parameters of Synchronous

Built-in Servo Motors
(1) Overview
The following describes the procedure for setting the digital servo
parameters to enable the use of a FANUC synchronous built-in servo
motor.
To drive a synchronous built-in servo motor, the optional pole
detection function is required.

Series 90B3/P(16) and subsequent editions
(Series 0i-C)
(3) Warning
WARNING
1 A synchronous built-in servo motor can make an
unpredictable movement or vibration if the basic
parameters for pole detection and so forth are not
set correctly.
2 It is recommended to take the following actions
until normal operation is confirmed:
- Lower the excessive error level so that an alarm
is issued immediately when an unpredictable
movement is made.
- Lower the torque limit value to disable abrupt
acceleration.
- Ensure that the emergency stop switch can be
pressed immediately.
- 346 -
(4) Detector
A rotary encoder is used to detect the position and speed of a
synchronous built-in servo motor.
Table 4.15.1(a) lists examples of usable rotary encoders.
A non-binary encoder is a detector with the number of AB-phase sine

waves (λ) per detector revolution not being 2 raised to some power
(2N).
Table 4.15.1 (a) Examples of usable rotary encoders

Number of pulses for
Encoder Remarks
parameter setting (*1)
αiCZ 512A 500,000 p/rev Manufactured by FANUC
αiCZ 768A (*2)
750,000 p/rev Manufactured by FANUC
αiCZ 1024A 1,000,000 p/rev Manufactured by FANUC
RCN220 1,000,000 p/rev Manufactured by HEIDENHAIN
RCN727(*3) 8,000,000 p/rev Manufactured by HEIDENHAIN
Non-binary encoder λ: Number of sine waves per
λ × 512p/rev
＋ High resolution serial output circuit(*2) detector revolution
(*1) Number of pulses for parameter setting, which differs from an

actual resolution.
(*2) To use αiCZ 768A or a set of non-binary encoder + high
resolution serial output circuit as a detector for a synchronous
built-in servo motor, the following servo software is needed:
Series 90B1/C(03) and subsequent editions (Series15i, 16i and
so on)
Series 90B8/C(03) and subsequent editions (Series 0i-C)
Series 90D0, 90E0/J(10) and subsequent editions (Series 30i
and so on)
Series 90D3/B(02) and subsequent editions, Series 90E3/A(01)
and subsequent editions (Series 30i and so on)
Series 90B3 and 90B7 are unusable. (Series 16i and so on,
Series 0i-C)
To use a synchronous built-in servo motor position detection
circuit (A860-2033-T601) for a high resolution serial output
circuit, the following servo software is needed:
Series 90B1/K(11) and subsequent editions (Series15i, 16i and
so on)
Series 90B8/K(11) and subsequent editions (Series 0i-C)
Series 90D0, 90E0/P(16) and subsequent editions (Series 30i
and so on)
Series 90B3 and 90B7 are unusable. (Series 16i and so on,
Series 0i-C)
Series 90D3 and 90E3 are unusable. (Series 30i and so on)
- 347 -
(*3) To use RCN727 as a detector for a synchronous built-in servo

motor, the following servo software is needed:
Series 90B1/F(06) and subsequent editions (Series 15i, 16i and
so on)
Series 90B8/F(06) and subsequent editions (Series 0i-C)
Series 90D0, 90E0/J(10) and subsequent editions (Series 30i
and so on)
Series 90D3, 90E3/ A(01) and subsequent editions (Series 30i
and so on)
Series 90B3/P(16) and subsequent editions (Series 16i and so
on)
Series 90B7/Q(17) and subsequent editions (Series 16i and so
on)
NOTE
1 For details of rotary encoders usable with FANUC
synchronous built-in servo motors, refer to "FANUC
SYNCHRONOUS BUILT-IN SERVO MOTOR DiS
series Descriptions (B-65332EN)".
2 For the detailed specifications of each rotary
encoder, contact each rotary encoder
manufacturer.
CAUTION
When using a set of non-binary encoder + high
resolution serial output circuit with a synchronous
built-in servo motor, note the following:
1 Absolute setting is disabled.
2 The movable range is within ±1 detector
revolution.
(Use assuming infinite revolution is disabled.)
3 Each time the power to the NC is turned on,
pole position detection must be performed
without fail.
- 348 -
(5) Parameter settings

Set the parameters according to the procedure below.
Procedure (1) can be used to initialize the parameters (such as current

gain) necessary to drive a synchronous built-in servo motor. After
initialization, the parameters dependent on the type of rotary encoder
need to be set. Set the parameters according to procedure (2) described
later.
Parameters related to initialization

#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) DGPR
2000 (FS30i, 16i)
DGPR(#1) Set 0. (After initialization, this bit is set to 1 automatically.)
1879 (FS15i) Movement direction

2022 (FS30i, 16i)
+111: When the positive direction is specified, the rotor rotates in the
positive direction.
-111: When the positive direction is specified the rotor rotates in the
reverse direction.
The positive direction (+ direction) of the DiS series motor is the

counterclockwise rotation of the rotor as determined by viewing the
motor from the power line side.
Power line
Cooling jacket
Stator
+ direction Rotor
- 349 -
Motor ID number

2020 (FS30i, 16i)
Table 4.15.1 (b) and Table 4.15.1 (c) indicate the synchronous built-in
servo motors for which the standard parameters are available as of
July, 2007. When the standard parameters are not included in the
servo software used, see the parameter list shown in this manual, and
set the parameters.
Table 4.15.1 (b) Synchronous built-in servo motor [200V driving]

Motor Motor ID 90B1 90D0
Motor model
specification No. 90B8 90E0
DiS 22/600 0482-B10x 421 I(09) P(16)
DiS 85/400 0483-B20x 423 H(08) K(11)
DiS 85/1000 0483-B224 443 I(09) P(16)
DiS 110/300 0484-B10x 425 H(08) K(11)
DiS 110/1000 0484-B124 445 I(09) P(16)
DiS 260/300 0484-B30x 427 I(09) N(14)
DiS 260/600 0484-B31x 429 H(08) K(11)
DiS 260/1000 0484-B324 447 I(09) P(16)
DiS 370/300 0484-B40x 431 H(08) K(11)
DiS 1200/250 0485-B50x 435 I(09) N(14)
DiS 1500/200 0486-B30x 437 I(09) N(14)
DiS 2100/150 0487-B30x 439 I(09) N(14)
DiS 3000/150 0487-B40x 441 I(09) N(14)
Table 4.15.1 (c) Synchronous built-in servo motor [400V driving]

Motor Motor ID 90B1 90D0
Motor model
specification No. 90B8 90E0
DiS 22/600 0482-B10x 422 I(09) P(16)
DiS 85/400 0483-B20x 424 H(08) K(11)
DiS 110/300 0484-B10x 426 H(08) K(11)
DiS 260/300 0484-B30x 427 I(09) N(14)
DiS 260/600 0484-B31x 430 H(08) K(11)
DiS 370/300 0484-B40x 432 H(08) K(11)
DiS 1200/250 0485-B50x 436 I(09) N(14)
DiS 1500/200 0486-B30x 438 I(09) N(14)
DiS 2100/150 0487-B30x 440 I(09) N(14)
DiS 3000/150 0487-B40x 442 I(09) N(14)

After parameter initialization, check that the function bit for

synchronous built-in servo motor control is set to 1 (synchronous
built-in servo motor control is enabled).
- 350 -
#7 #6 #5 #4 #3 #2 #1 #0
2713 (FS15i) DD
2300 (FS30i, 16i)
DD(#2) Synchronous built-in servo motor control is:
0: Disabled
1: Enabled
- 351 -
Procedure (2) can be used to set the parameters that need to be set
according to the type of a rotary encoder used.
Setting of parameters related to feedback
#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) PLC0
2000 (FS30i, 16i)
PLC0(#0) The number of velocity pulses and the number of position pulses are:
0: Used without being modified.
1: Used after being multiplied by 10
If the number of velocity pulses is lager than 32767, set the parameter
to 1.

2023 (FS30i, 16i)

2024 (FS30i, 16i)
2628 (FS15i) Position pulses conversion coefficient (PSMPYL)

2185 (FS30i, 16i)
This parameter is used if the calculated number of position pulses is
greater than 32767.
When this parameter is set to 0, PSMPYL=1 is assumed for
processing.

When PLC0=0
→ Set so that Number of position pulses = PPLS × PSMPYL.
When PLC0=1
→ Set so that Number of position pulses = 10 × PPLS × PSMPYL
Table 4.15.1 (d) Setting the number of velocity pulses and number of position pulses
PLC0 PULCO PPLS PSMPYL
Encoder
(No.2000#0) (No.2023) (No.2024) (No.2185)
αiCZ 512A 0 4096 6250 0
αiCZ 768A 0 6144 9375 0
αiCZ 1024A 0 8192 12500 0
RCN220 0 8192 12500 0
RCN223 1 6554 10000 0
RCN723 1 6554 10000 0
RCN727 1 6554 10000 0
Non-binary encoder
(*1)
＋ High resolution serial output circuit
- 352 -
(*1) When a set of binary-encoder + high resolution serial output

circuit is used, the number of velocity pulses and the number of
position pulses are calculated according to the following
expressions:
Number of velocity pulses＝2 × λ

Number of position pulses＝32 × λ/5
(λ: Number of sine waves per detector revolution)
1977 (FS15i) Flexible feed gear numerator

2084 (FS30i, 16i)
1978 (FS15i) Flexible feed gear denominator

2085 (FS30i, 16i)

Number of pulses per motor revolution
No. 2084
FFG = = (detection unit)
No. 2085 Number of pulses per detector revolution
For the number of pulses per detector revolution, see Table 4.15.1 (e).
Table 4.15.1 (e) Number of pulses for flexible feed gear setting
Number of pulses per
Encoder Remarks
detector revolution (*1)
αiCZ 512A 500,000 p/rev FFG, maximum value is 1/1.
αiCZ 768A 750,000 p/rev FFG, maximum value is 1/1.
αiCZ 1024A 1,000,000 p/rev FFG, maximum value is 1/1.
RCN220 1,000,000 p/rev FFG, maximum value is 1/1.
Non-binary encoder
λ×512p/rev FFG, maximum value is 4/1.
＋ High resolution serial output circuit
(*1) Number of pulses for parameter setting, which differs from an
actual resolution.

1821 (FS30i, 16i)
Set the number of pulses per motor revolution (detection unit) or the
same number divided by an integer.
With αiCZ 768A, however, set the number of pulses per one-third of
one motor revolution (detection unit) or the same number divided by
an integer.
- 353 -
#7 #6 #5 #4 #3 #2 #1 #0
2688 (FS15i) RCNCLR 800PLS
2275 (FS30i, 16i)
800PLS (#0) A rotary encoder with eight million pulses per revolution is:
0: Not to be used.
1: To be used. (To use the RCN223, RCN723, or RCN727, set the
bit to 1.)
RCNCLR (#1) The number of revolution is:

0: Not to be cleared.
1: To be cleared. (To use the RCN220, RCN223, RCN723, or
RCN727, set the bit to 1.)
This function bit is to be set in combination with the number of data
mask digits, described below.
2807 (FS15i) Number of data mask digits (DMASK)

2394 (FS30i, 16i)
[Settings] 8. (To use the RCN223, RCN723, or RCN727)
5. (To use the RCN220)
This parameter need not be set for an αiCZ sensor. (When using an
αiCZ sensor, set this parameter to 0.)
Set this parameter together with RCNCLR above.
Setting of an AMR conversion coefficient

#7 #6 #5 #4 #3 #2 #1 #0
2001 (FS30i, 16i)
Set the value that matches the type of a rotary encoder used, according
to Table 4.15.1 (f).
Table 4.15.1 (f) Setting AMR
Encoder AMR6-AMR0 Remarks
αiCZ 512A Set the number of motor poles in binary.
αiCZ 768A Set 0.
αiCZ 1024A Set the number of motor poles/2 in binary.
RCN220 Set the number of motor poles/2 in binary.
RCN223 Set the number of motor poles in binary.
Non-binary encoder
Set 0.
+ High resolution serial output circuit
- 354 -
#7 #6 #5 #4 #3 #2 #1 #0
2608 (FS15i) DECAMR
2220 (FS30i, 16i)
Set the value that matches the type of a rotary encoder used, according to Table 4.15.1 (g).
Table 4.15.1 (g) Setting DECAMR
Encoder DECAMR Remarks
αiCZ 512A Set 0.
αiCZ 768A Set 1.
αiCZ 1024A Set 0.
RCN220 Set 0.
RCN223 Set 0.
RCN723 Set 0.
RCN727 Set 0.
Non-binary encoder
Set 1.
1705 (FS15i) AMR conversion coefficient 1 (AMRDL)

2112 (FS30i, 16i)
1761 (FS15i) AMR conversion coefficient 2 (AMR2)

2138 (FS30i, 16i)
Set the value that matches the type of a rotary encoder used, according
to Table 4.15.1 (h).
Table 4.15.1 (h) Setting AMRDL and AMR2
AMR conversion
AMR conversion coefficient 2
Encoder coefficient 1
( AMR2 : No.2138 )
( AMRDL : No.2112 )
αiCZ 768A Set 768. Set the number of motor poles/2.
RCN220 Set 0. Set 0.
RCN223 Set 0. Set -4.
Non-binary encoder
Set λ. (*1)(*2) Set the number of motor poles/2.
(*1) When λ exceeds 32767, find an AMR conversion coefficient 1
value less than 32767 by dividing AMR conversion coefficient 1
and AMR conversion coefficient 2 by a common divisor and set
the found value in the parameter.
(*2) If "support for the input frequency 750 kHz" is specified when a
set of non-binary encoder + high resolution serial output circuit
is used (SW3=A and bit 0 of No. 2274=1), set the value λ/4 as
AMR conversion coefficient 1.
- 355 -
Setting for using only a set of non-binary encoder + high resolution serial output circuit
When using a set of non-binary encoder + high resolution serial output
circuit, set both of the parameters below to 1. (These parameters need
not be set for any other configurations.)
#7 #6 #5 #4 #3 #2 #1 #0
1954(FS15i) LINEAR
2010(FS30i 16i)
circuit, set LINEAR=1.
#7 #6 #5 #4 #3 #2 #1 #0
2687(FS15i) HP2048
2274(FS30i 16i)
circuit, set HP2048=1.
Summary of parameter setting according to the type of rotary encoder

Tables 4.15.1 (i), (j), (k), (l), and (m) provide summarized examples of
parameter setting according to the type of rotary encoder. Set
parameters according to the types of a rotary encoder and synchronous
built-in servo motor used.
For the number of poles of each motor model, see Table 4.15.1 (n).
Table 4.15.1 (i) For αiCZ 512A
Parameter number Parameter setting
Symbol Detection Detection
name FS30i,16i FS15i unit unit
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 0 0
PLC0 2000#0 1804#0 0 0
Number of Number of
AMR 2001 1806
poles (binary) poles (binary)
PULCO 2023 1876 4096 4096
PPLS 2024 1891 6250 6250
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 36 36
FFG 2085 1978 50 5
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
- 356 -
Table 4.15.1 (j) For αiCZ 768A

Symbol
name Detection unit Detection unit
FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 768 768
Number of Number of
AMR2 2138 1761
poles/2 poles/2
PLC0 2000#0 1804#0 0 0
AMR 2001 1806 00000000 00000000
PULCO 2023 1876 6144 6144
PPLS 2024 1891 9375 9375
REFCOUNT 1821 1896 120000 1200000
FFG 2084 1977 36 360
FFG 2085 1978 75 75
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 1 1
Table 4.15.1 (k) For αiCZ 1024A

Symbol
FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 0 0
PLC0 2000#0 1804#0 0 0
Number of Number of
AMR 2001 1806 poles/2 poles/2
(binary) (binary)
PULCO 2023 1876 8192 8192
PPLS 2024 1891 12500 12500
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 36 36
FFG 2085 1978 100 10
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
- 357 -
Table 4.15.1 (l) For RCN220

Symbol
FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 0 0
PLC0 2000#0 1804#0 0 0
Number of Number of
AMR 2001 1806
poles/2 (binary) poles/2 (binary)
PULCO 2023 1876 8192 8192
PPLS 2024 1891 12500 12500
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 36 36
FFG 2085 1978 100 10
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
800PLS 2275#0 2688#0 0 0
RCNCLR 2275#1 2688#1 1 1
DMASK 2394 2807 5 5
Table 4.15.1 (m) For RCN223, RCN723, or RCN727

Symbol
FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 -4 -4
PLC0 2000#0 1804#0 1 1
Number of Number of
AMR 2001 1806
PULCO 2023 1876 6554 6554
PPLS 2024 1891 10000 10000
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 9 9
FFG 2085 1978 200 20
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
800PLS#0 2275#0 2688#0 1 1
800PLS#1 2275#1 2688#1 1 1
DMASK 2394 2807 8 8
- 358 -
Table 4.15.1 (n) When using a set of non-binary encoder + high resolution
serial output circuit
Symbol
FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 λ λ
Number of
AMR2 2138 1761 Number of poles/2
poles/2
PLC0 2000#0 1804#0 0 0
AMR 2001 1806 00000000 00000000
PULCO 2023 1876 2λ 2λ
PPLS 2024 1891 32λ/5 32λ/5
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 360000 3600000
Reduction of Reduction of
FFG 2085 1978 λ × 512 λ × 512
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 1 1
LINEAR 2010#2 1954#2 1 1
HP2048 2274#0 2687#0 1 1
Table 4.15.1 (o) Number of poles and number of pole

pairs of each motor model
Number of pole
Motor model Number of poles pairs (number of
poles/2)
DiS 22/600 24 12
DiS 85/400 32 16
DiS 85/1000 32 16
DiS 110/300 40 20
DiS 110/1000 40 20
DiS 260/300 40 20
DiS 260/600 40 20
DiS 260/1000 40 20
DiS 370/300 40 20
DiS 1200/250 56 28
DiS 1500/200 72 36
DiS 2100/150 88 44
DiS 3000/150 88 44
- 359 -
Parameter setting procedure (3): Pole position detection
To drive a synchronous built-in servo motor, the pole detection

function (option) is required. Procedure (3) describes the pole
detection function.
(1) Overview
The pole detection function detects the pole position of a motor to be
driven when the relationship between the pole position of the motor
and the phase of the detector is unknown.
WARNING
1 This function may be unable to detect the correct pole position, depending on the
detection condition, resulting in an unpredictable motor movement. To avoid this
dangerous situation, the following conditions must be satisfied until completion of
detection:
<1> The torque limit parameter (FS30i, 16i: No. 2060, FS15i: No. 1872) must be
set so that 150% of the current needed for ordinary operation is not exceeded.
<2>The setting of excessive error at stop time must be 100 µm or 0.1 deg or less.
Moreover, the setting of excessive error at move time must be 120% of the
logical positional deviation or less.
<3> While pole position detection is in progress and a subsequent move operation
is specified, the protection doors must be closed.
If these conditions are not satisfied and pole position detection operation is not
terminated normally, the motor can make an unpredictable movement with the
maximum torque until the NC detects an excessive error alarm.
For safety, create the following sequence with the PMC by using the pole detection
state signal:
<1> When the protection doors are open, pole detection is not started.
<2> If a protection door is opened during pole detection (Fn158=1), a reset is made.
<3> When pole detection is uncompleted (Fn159=0), no command is issued to
relevant axes.
<4> When pole detection is uncompleted (Fn159=0), the brake for the vertical axis
is not released. (For brake operation, monitor not only the SA signal but also
the pole detection completion signal.)
In general, this function cannot be applied to the following motors and conditions:
<1> Linear motor
<2> Axis for which the axis separation function (detach) is used (See Item (8) in this
section.)
<3> When the joint rigidity between the motor and detector is low
However, when this function needs to be used for an unavoidable reason, pay full
attention to safety and use this function with only the following:
<1> Linear motor using an absolute value detector
- 360 -
WARNING
2 For the following conditions, use a specified servo series/edition. Otherwise, the
pole position cannot be detected correctly.
<1> When a detector that has an absolute address referenced mark is used.
<2>When an αiCZ or αA1000S sensor is used.
<3> When this function is applied to an axis such as a vertical axis that is
completely locked.
(Specified series/edition)
- Series 90B1/B(02) and subsequent editions (FS15i, 16i and so on)
- Series 90B8/B(02) and subsequent editions (FS0i-C)
- Series 90D0, 90E0/J(10) and subsequent editions (FS30i and so on)
- Series 90D3, 90E3/A(01) and subsequent editions (FS30i and so on)
- Series 90B3/P(16), 90B7/Q(17) and subsequent editions (FS16i and so on)
CAUTION
1 When two axes are placed under tandem control or simple synchronous control
and each of the two axes has a speed detector (Pulsecoder or linear scale for a
linear motor), ensure that an axis not detected is placed in the servo-off state and
pole detection is performed for each of the main axis and sub-axis.
2 When using the motor feedback sharing function (FS16i, 30i: No. 2018#7, FS15i:
No. 1960#7) under tandem control, start pole detection simultaneously for the two
axes to avoid incorrect detection.
3 When a resonance elimination filter is used with a machine that has less friction, an
excessive error alarm may be issued during detection, or a pole position may not
be detected correctly. Turn off all resonance elimination filters or set bit 3 of No.
2283 to 1 (with FS16i and 18i only).
4 For a detector to be applied, note the following:
1) Use an absolute detector whenever possible.
2) If the use of an incremental detector is unavoidable, an incremental detector with
a one-rotation signal is recommended.
3) If a one-rotation signal is unavailable with an incremental detector, the torque
constant may slightly change due to fluctuation in detection.
NOTE
This function is optional function.
- 361 -
(2) Applicable software

To use the pole position detection function, the CNC software and
servo software that support the function are needed.
Applicable CNC software

FS16i -MA B0F2-04 and subsequent editions
FS16i -TA B1F2-04 and subsequent editions
FS18i -MA BDF2-04 and subsequent editions
FS18i -TA BEF2-04 and subsequent editions
FS21i -MA DDF2-04 and subsequent editions
FS21i -TA DEF2-04 and subsequent editions
NOTE
To use an absolute position detector (bit 4 of No.
1815=1), edition 19 or later is needed.
FS30i -A Supported starting with the first edition

FS16i -MB/TB Supported starting with the first edition
FS15i -MB F0A1-10 and subsequent editions
F6A1-10 and subsequent editions
Power Mate i-MODEL D 88E0-21 and subsequent editions
Power Mate i-MODEL H 88F1-12, 88F2-02 and subsequent
editions
Applicable servo software

90A8-01 and subsequent editions
90A7-02 and subsequent editions
90B7-01 and subsequent editions
90D0,E0-01 and subsequent editions
90D3,E3-01 and subsequent editions
NOTE
When using this function with a linear motor, use
the following servo software:
90B0/Q(17) and subsequent editions, 90B3/G(07)
and subsequent editions, 90B7/G(07) and
subsequent editions, 90B1/B(02) and subsequent
editions, 90B8/B(02) and subsequent editions,
90D0,E0/J(10) and subsequent editions,
90D3,E3/A(01) and subsequent editions
- 362 -
(3) Details for pole position detection function

Pole detection sequence
• Enable the parameter (FS30i, 16i: No. 2213#7, FS15i: No.
2601#7) for a target axis. Pole position detection is performed
only for an enabled axis. For an axis not enabled, the pole
position detection request signal (Gn135) is ignored.
• Set the servo-on state.
Here, ensure that the brake for a vertical axis must not be
released until the detection completion signal (Fn159) is set to 1.
• Do not perform a pole position detection operation in the
servo-off state. Moreover, do not set the servo-off state during
pole position detection operation.
• When the pole position detection request signal (Gn135) is set to
1, pole position detection is started, and the pole position
detection in-progress signal (Fn158) is set to 1.
• Once a pole position detection operation is started, the detection
operation is continued even when the pole position detection
request signal is set to 0.
• Motor operation during pole position detection is not under
control of the CNC. During this period, the CNC performs a
follow-up operation.
• Upon completion of pole position detection after several seconds,
the pole position detection in-progress signal (Fn158) is set to 0,
and the pole position detection completion signal (Fn159) is set
to 1.
• If pole position detection is terminated abnormally for a
mechanical cause or motor characteristics, the servo alarm
"POLE DETECTION ERROR" is issued.
• The servo alarm "POLE DETECTION ERROR" cannot be
released with a reset. Turn off the power then turn on the power
again.
• When a reset is made during pole position detection, the pole
position detection is stopped. To restart pole position detection,
set the pole position detection request signal to 0 then set the
same signal to 1 again.
• Once a pole position detection operation is completed, no
additional pole position detection operation can be performed
until the power is turned off.
• When using an absolute detector, set the parameter (FS30i, 16i:
No. 2229#0, FS15i: No. 2617#0) to 1. In this case, when pole
position detection is completed, the result of detection is stored
in the parameter (FS30i, 16i: No. 2139, FS15i: No. 1762). So,
pole position detection need not be performed each time the
power is turned on.
• In the MDI, MEM, or EDIT mode, the result of detection is
reflected on the screen immediately. In the REF or JOG mode,
the result of detection is reflected on the screen when the reset
key is pressed or the mode is switched to the MDI mode.
• Before restarting pole detection, clear the parameter (FS30i, 16i:
No. 2139, FS15i: No. 1762) to 0.
- 363 -
• When pole position detection is completed and the motor

one-rotation signal is detected, the result of detection is stored in
the parameter (FS30i, 16i: No. 2139, FS15i: No. 1762) in the
MDI mode by setting the parameter (FS30i, 16i: No. 2229#0,
FS15i: No. 2617#0) to 1 also in the case where an incremental
detector is used. Thus, a torque constant change due to pole
position detection variation can be avoided.
NOTE
1 When an absolute detector is used and the parameter
(FS30i, 16i: No. 2229#0, FS15i: No. 2617#0) is set to 1,
the pole position detection completion signal (Fn159) is
set to 1 immediately after power-on if the parameter
(FS30i, 16i: No. 2139, FS15i: No. 1762) is not set to 0.
2 Create logic for confirming the pole position detection
completion signal (Fn159) before specifying a move
command immediately after power-on.
3 If an alarm such as a count error alarm is issued for a
detector fault, the pole position detection completion
signal (Fn159) is returned to 0. In this case, perform
another pole position detection operation.
Detection mode and method of application
With servo series 90B1 and 90B8/B(02) or later, servo series 90D0
and 90E0/J(10) or later, or servo series 90D3 and 90E3/A(01) or later,
the three detection modes indicated below are available. With other
servo series/editions, only the minute operation mode in 1) below can
be used.
1) Minute operation mode

Operation: A pole position is detected with the motor making
a minute operation.
Application: When the friction is less so that the motor can
move in a minute range
Setting: No.2229#4=1, No.2182≥0 (FS30i,16i)
No.2617#4=1, No.2625≥0 (FS15i)
Usually, it is recommended to use this mode.

2) Automatic selection mode
Operation: The minute operation mode is initially used for
detection. If the motor is locked or the friction is
larger, the detection mode is automatically
switched to the stop mode.
Application: A pole position can be detected, regardless of the
machine state.
Setting: No.2229#4=0, No.2182≧0 (FS30i,16i)
No.2617#4=0, No.2625≧0 (FS15i)
- 364 -
3) Stop mode
Operation: A pole position is detected with the motor placed
in the stop state.
Application: Axis such as a vertical axis where the motor is
locked
Setting: No.2229#4=0, No.2182=-1 (FS30i,16i)
No.2617#4=0, No.2625=-1 (FS15i)
NOTE
As the guideline for stop mode application, the
following conditions apply:
1) The motor saliency (=Ld-Lq) is 1 mH or more.
2) Magnetic saturation occurs at a current larger
than the rated motor current by a factor of 2 or
less.
(The torque constant is reduced by 5% or more.)
If these conditions are not satisfied, the precision
may be degraded or detection may be disabled.
Note that some models of FANUC DiS series do
not satisfy these conditions, thus disabling the stop
method from being used.
When using the stop mode, make a sufficient
operation check beforehand.
When the automatic selection mode is used, the
mode is switched from the minute operation mode
to the stop mode automatically, depending on the
axis state. So, before using the automatic selection
mode, check that normal operation can be
performed in the stop mode.
(4) Parameters for pole position detection function

When this parameter has been modified, the power to the NC must be
#7 #6 #5 #4 #3 #2 #1 #0
2601 (FS15i) OCM
2213 (FS30i, 16i)
OCM(#0) 0: The pole detection function is disabled.
1: The pole detection function is enabled.
- 365 -
#7 #6 #5 #4 #3 #2 #1 #0
2616 (FS15i) ELSAL
2228 (FS30i, 16i)
ELSAL(#0) 0: The motor saliency is Lq>Ld.
1: The motor saliency is Lq<Ld.
This parameter is related only to a case where the stop mode is used.
When a synchronous motor (IPM) of magnet-embedded type is used,
the motor saliency is Lq>Ld (reverse saliency). In rare cases, however,
a synchronous motor of magnet surface attachment type (SPM) may
indicate the saliency Lq<Ld. In this case, the detection phase is shifted
90 degrees relative to the reverse saliency. With many motors,
however, saliency information acquisition is presently difficult. So, if
the results of repeated detections always indicate a shift of 90 degrees,
set this bit.
NOTE
This parameter can be used with series 90B1/B(02)
or later (FS15i, 16i, etc.), series 90B8/B(02) or later
(FS0i-C), series 90D0 and 90E0/J(10) or later
(FS30i, etc.), and series 90D3 and 90E3/A(01) or
later (FS30i, etc.).
#7 #6 #5 #4 #3 #2 #1 #0
2617 (FS15i) FORME WATRA ABSEN
2229 (FS30i, 16i)
ABSEN(#0) 0: AMR offset (FS30i, 16i: No. 2139, FS15i: No. 1762) is not used.
1: AMR offset (FS30i, 16i: No. 2139, FS15i: No. 1762) is used.
If an absolute detector is used, the result of detection is saved to the

AMR offset of the parameter (FS30i, 16i: No. 2139, FS15i: No. 1762).
In the case of a second or subsequent power-on operation, pole
position detection need not be executed.
If an incremental detector is used, the result of detection is saved to
the AMR offset when the one-rotation signal is detected. In this case,
pole position detection needs to be performed each time the power is
turned on. After the one-rotation signal is detected, however, the value
saved to the AMR offset is used, so that an influence due to pole
detection variation can be eliminated.
- 366 -
WATRA(#3) 0: After pole detection, an abnormal movement is monitored.

1: After pole detection, no abnormal movement is monitored.
If a detection error occurs, protection against an abnormal operation is

provided. Operation is monitored until a command after detection is
issued. If an abnormal operation is detected, detection error alarm
SV0454 is issued.
NOTE
FORME(#4) 0: Automatic selection mode (minute operation mode + stop mode)

1: Minute operation mode
Usually, set this parameter to 1 (minute operation mode).
NOTE
1762 (FS15i) AMR offset (AMROFS)

2139 (FS30i, 16i)
[Unit of data] Degrees
If ABSEN=1, the result of operation is stored in this parameter when
the MDI mode is set upon completion of detection.
WARNING
After pole determination, never rewrite the value of
this parameter manually. If this parameter is
rewritten for adjustment, the power must be turned
off before operation is continued.
- 367 -
2625 (FS15i) Current A for pole detection (DTCCRT_A)

2182 (FS30i, 16i)
[Unit of data] 7282 is the maximum amplifier current value.
Set a current value for pole position detection. If this parameter is set
to 0, pole position detection is performed according to the value of the
rated current parameter (FS30i, 16i: No. 2086, FS15i: No. 1979). If
the static friction of the machine is large, and the pole detection error
alarm is issued during detection, increase current A for pole detection.
The maximum value of this parameter is limited by the torque limit
parameter (FS30i, 16i: No. 2060, FS15i: No. 1872).
NOTE
When -1 is set, the stop mode is used for detection.
The setting of -1 can be used with series 90B1/B(02)
2641 (FS15i) Current B for pole detection (DTCCRT_B)

2198 (FS30i, 16i)
[Unit of data] % unit
Set a current value for pole direction detection. When this parameter is
set to 0, 100% is set internally.
NOTE
- 368 -
2642 (FS15i) Current C for pole detection (DTCCRT_C)

2199 (FS30i, 16i)
[Unit of data] 7282 is the maximum amplifier current value.
Set a current value for pole direction detection. When this parameter is
set to 0, 100% is set internally. When this parameter is set to 0, pole
position detection is performed using a current value two times greater
than the value of the rated current parameter (FS30i, 16i: No. 2086,
FS15i: No. 1979).
NOTE
2681 (FS15i) Allowable travel distance magnification/stop speed decision value

(MFMPMD)
2268 (FS30i, 16i)
[Unit of data] % unit
[Standard setting] 0 (100% internally)
During pole position detection, the motion of the rotor is limited to
within an allowable travel distance of 5 degrees. If the value of this
parameter is positive, set an allowable travel distance by specifying a
percentage relative to the default value 5 degrees. If the pole detection
error alarm is issued during pole position detection, and no
improvement is made by changing the current value for pole detection,
set a value greater than 100% in this parameter. For example, to set an
allowable travel distance of 10 degrees, set 200%.
If the value of this parameter is negative, the stop speed decision
criterion to be used when a low-resolution detector is used can be
changed. If pole detection is not started, change the value of this
parameter to a greater negative value. For example, set a value from
-200 to -500 for adjustment.
NOTE
The setting of a negative value can be used with
series 90B1/B(02) or later (FS15i, 16i, etc.), series
90B8/B(02) or later (FS0i-C), series 90D0 and
90E0/J(10) or later (FS30i, etc.), and series 90D3
and 90E3/A(01) or later (FS30i, etc.).
- 369 -
(5) Signals for pole position detection function

Pole position detection request signal
RPREQ1 to RPREQ8
[Function] Requests pole position detection. This signal is available for each
controlled axis, and the suffix at the end of each signal name indicates
a controlled axis number.
[Operation] Pole position detection is started by setting this signal to 1. Once a
pole position detection operation is started, the operation is continued
even when this signal is set to 0.
Pole position detection in-progress signal

RPDET1 to RPDET8
[Classification] Output signal
[Function] Posts that pole position detection is being performed. This signal is
available for each controlled axis, and the suffix at the end of each
signal name indicates a controlled axis number.
[Output condition] This signal is set to 1 in the following case:
- When pole position detection is being performed
This signal is set to 0 in one of the following cases:
- When pole position detection is completed
- When pole position detection is terminated abnormally
- When pole position detection is stopped by a reset
- 370 -
Pole position detection completion signal

RPFIN1 to RPFIN8
[Function] Posts that pole position detection is completed. This signal is available
for each controlled axis, and the suffix at the end of each signal name
indicates each controlled axis number.
[Output condition] This signal is set to 1 in the following case:
- When pole position detection is completed after pole position
detection is started by setting the pole position detection request
signal to 1
RPREQ
RPDET
RPFIN
NOTE
1 If an absolute detector is used, this signal remains
set to 1 even when the power is turned off then
back on after completion of pole position detection
performed by setting the parameter (FS30i, 16i: No.
2229#0, FS15i: No. 2617) to 1. When the power is
turned off then back on after setting the parameter
(FS30i, 16i: No. 2139, FS15i: No. 1762) to 0, this
signal is set to 0.
2 If an incremental detector is used, the pole position
detection completion signal is not set to 0 unless
the power is turned off.
Signal address
For Series 30i, 16i, and Power Mate i

#7 #6 #5 #4 #3 #2 #1 #0
Gn135 RPREQ8 RPREQ7 RPREQ6 RPREQ5 RPREQ4 RPREQ3 RPREQ2 RPREQ1
#7 #6 #5 #4 #3 #2 #1 #0
Fn158 RPDET8 RPDET7 RPDET6 RPDET5 RPDET4 RPDET3 RPDET2 RPDET1
Fn159 RPFIN8 RPFIN7 RPFIN6 RPFIN5 RPFIN4 RPFIN3 RPFIN2 RPFIN1
- 371 -
For Series 15i

#7 #6 #5 #4 #3 #2 #1 #0
G067 RPREQ1
G071 RPREQ2
G075 RPREQ3
G079 RPREQ4
G083 RPREQ5
G087 RPREQ6
G091 RPREQ7
G095 RPREQ8
G099 RPREQ9
G103 RPREQ10
G107 RPREQ11
G111 RPREQ12
G115 RPREQ13
G119 RPREQ14
G123 RPREQ15
G127 RPREQ16
G243 RPREQ17
G247 RPREQ18
G251 RPREQ19
G255 RPREQ20
G259 RPREQ21
G263 RPREQ22
G267 RPREQ23
G271 RPREQ24
- 372 -
#7 #6 #5 #4 #3 #2 #1 #0
F067 RPFIN1 RPDET1
F071 RPFIN2 RPDET2
F075 RPFIN3 RPDET3
F079 RPFIN4 RPDET4
F083 RPFIN5 RPDET5
F087 RPFIN6 RPDET6
F091 RPFIN7 RPDET7
F095 RPFIN8 RPDET8
F099 RPFIN9 RPDET9
F103 RPFIN10 RPDET10
- 373 -
(6) Action for trouble for pole position detection function
Detection During Detection

Symptom State request detection completion Cause Action
(Gn135) (Fn158) (Fn159)
[Before detection completion]
In the minute operation The pole detection
Turn on the pole
mode, the motor moves OFF OFF OFF request signal is
detection request signal.
slightly. turned off.
Detection is In the stop mode, a The pole detection
not started. varying activating Check bit 7 of No. 2213
function is
sound, which is to be ON OFF OFF or the option.
disabled.
heard, cannot be
confirmed. Servo-off Set the servo-on state.
Use the following:
90B1, 90B8/B(02) or later
An α
 i CZ sensor is
90B3/P(16) or later
used.
90B7/Q(17) or later
An α A1000S is
90D0, 90E0/J(10) or
used.
later, 90D3, 90E3/A(01)
or later
The motor appears to The detector Set the stop speed
be moving slightly. resolution is low: decision value (No. 2268)
However, detection is 100 million/rev or to a value from -200 to
Detection is not completed and no lower -500.
not alarm is issued. ON ON OFF Velocity feedback Take action for noise
completed. noise protection.
The friction is very
small, so that
Decrease detection
activation causes a
current A (No. 2182) to
vibration to disable
find an optimal value.
stop decision
initiation.
During detection, an Increase the stop speed
abnormally large motion Detector with high
is made and detection is decision value (No.
resolution
not completed. 2268).
Increase the setting of
excessive error at stop
The friction is
time or set detection
Excessive During detection, the small.
current A (No. 2182) to
error at stop excessive error alarm at ON ON OFF
the rated current or lower.
time stop time is issued.
Influence of Turn off all resonance
resonance elimination filters or set
elimination filters bit 3 of No. 2283 to 1.
Set detection current A
The friction is
(No. 2182) to the rated
large.
current or higher.
Detection
The pole detection error The current gain is
error alarm ON ON OFF Set a proper current gain.
alarm is issued. small.
(SV454)
Set detection current B
The motor saliency
(No. 2198) to 100% or
is small.
more.
- 374 -

(G135) (F158) (F159)
[After detection completion]
The phase order of
the power line does
Change the phase
not match the
order of the power line.
direction of the
detector.
Vibration ON ON ON Set a correct detector
Detector setting error
resolution.
The number of poles Set the correct number
is not set correctly. of motor poles.
The velocity gain is Adjust the velocity gain
high. to a proper value.
The phase order of
the power line does
Change the phase
not match the
order of the power line.
direction of the
detector.
The number of poles Set the correct number
is not set correctly. of motor poles.
Set detection current B
The motor saliency is
(No. 2198) to 100% or
small.
Excessive An unpredictable more.
error at stop movement is made, or Set detection current C
time no movement is made in The motor is not (No. 2199) to a value
or response to an issued ON ON ON magnetically larger than the rated
excessive command, so that an saturated. current by a factor of 2
error at excessive error alarm is or more.
move time issued. Set bit 3 of No. 2228 to
No reverse saliency
1.
Use the following:
90B1, 90B8/B(02) or
later
+ circuit C with a 90B3/P(16) or later
referenced mark 90B7/Q(17) or later, or
90D0, 90E0/J(10) or
later, 90D3,
90E3/A(01) or later
Set bit 0 of No. 2229 to
Bit 0 of No. 2229 = 0
1.
After detection
The AMR The mode is not the The display is updated
completion, the result of
offset does ON ON ON MDI mode. in the MDI mode.
detection is not written
not change. The motor needs to
to the AMR offset.
Incremental detector make one or more
revolutions.
After detection
Detection
completion, the pole The VCMD mode is Set bit 3 of No. 2229 to
error alarm ON ON ON
detection error alarm is used for operation. 1.
(SV454)
issued.
- 375 -

(G135) (F158) (F159)
[After restart]
Pole detection needs to
The AMR offset is not 0, be performed each
Incremental detector
but no movement is time a start-up
No motion - - -
made in response to an operation is performed.
issued command. Pole detection needs to
Detector alarm
be performed again.
Set detection current A
The friction is large. (No. 2182) to the rated
Detection The value of the AMR
current or higher.
result offset varies in each - - -
variation detection operation. Set detection current B
The motor saliency is
(No. 2198) to 100% or
small.
more.
- 376 -
(7) Detection of the pole position detection request alarm

The pole position detection function specifies that no torque occurs on
an axis where pole position detection is not completed (servo-off
state). So, conventionally, the customer's ladder needs to monitor the
pole position detection completion signal in order to judge whether to
release the brake of an axis or to specify a move command for an axis.
The servo software and CNC software indicated below execute the
following processing when pole position detection is not completed
[pole position detection enabled (bit 7 of No. 2213=1) and the pole
position detection completion signal is off (Fn159=0)]:
1) The interlock state is set. (Interlock is applied onto each axis.
"INTER/START LOCK ON" on the diagnosis screen No. 0000
displays 1.)
2) The servo ready signal SA is turned off (the SA signal for all
axes is turned off.)
3) Alarm DS0650 is displayed (cleared by a reset).
Safety is thus ensured even if the customer's ladder processing is not
performed.
• For the following series, edition 21.0 or later is usable.
FS30i-A : G002, G012, G022, G032
FS31i-A5 : G121, G131
FS31i-A : G101, G111
FS32i-A : G201
FS30i-A : G003, G013, G023, G033
FS31i-A5 : G123, G133
FS31i-A : G103, G113
FS32i-A : G203
The alarm number and message are indicated below.
Number Message Description
DS0650 POLE DETECTION With an absolute detection axis (bit 5 of No. 1815=1),
REQUEST pole position detection is not completed (Fn159=0).
With a non-absolute detection axis (bit 5 of No.
1815=0), pole position detection is once completed
then the state is changed to the pole position
detection uncompleted state (Fn159=0).
- 377 -
With the parameters below, operation to be performed when pole

position detection is not completed can be changed.
#7 #6 #5 #4 #3 #2 #1 #0
1809(FS30i) PAO SAN
[Input type] Parameter input

[Data type] Bit path
#0 SAN When the pole position detection function is used, pole position
detection is enabled (bit 7 of No. 2213=1), and pole position detection
is not completed (Fn159=0) with an axis, the servo ready signal SA
<Fn000.6> of the path to which the axis belongs and the servo ready
signals SA8 to SA1 <Fn186.7 to Fn186.0> for all axes that belong to
the path are:
0: Not set to 0.
1: Set to 0.
CAUTION
When applying pole position detection to a gravity
axis, basically release the brake after confirming
pole position detection completion (Fn159=1) and
the servo ready signal. When releasing the brake
by checking the servo ready signal alone for an
avoidable reason, set this parameter to 1.
#1 PAO When the pole position detection function is used, pole position
detection is enabled (bit 7 of No. 2213=1), and pole position detection
is not completed (Fn159=0) with an axis:
0: Alarm DS0650 (POLE DETECTION REQUEST) is issued.
1: Alarm DS0650 (POLE DETECTION REQUEST) is not issued.
NOTE
1 The issue condition of alarm DS0650 varies,
depending on whether the axis in question is an
absolute detection axis, as described below.
- The alarm is issued with an absolute detection
axis (bit 5 of No. 1815=1) when pole position
detection is not completed (Fn159=0).
- The alarm is issued with a non-absolute
detection axis (bit 5 of No. 1815=0) when pole
position detection is once completed then the
state is changed to the pole position detection
uncompleted state (Fn159=0).
2 If this alarm is issued, detect a pole position again.
After a pole position is detected again, this alarm is
cleared by a reset.
- 378 -
(8) Using the pole position detection function and detach function (control
axis detach function) together
When the pole position detection function is used with an axis of a
synchronous built-in servo motor, motor switching using the detach
function is conventionally impossible. However, the servo software
and CNC software of the series and editions indicated below enable
the pole position detection function and detach function to be used at
the same time.


FS30i-A : G002, G012, G022, G032
FS31i-A5 : G121, G131
FS31i-A : G101, G111
FS32i-A : G201
FS30i-A : G003, G013, G023, G033
FS31i-A5 : G123, G133
FS31i-A : G103, G113
FS32i-A : G203
CAUTION
1 When switching is made by using the detach
function among those motors that need the pole
position detection function, the motors and
detectors need to be of the same type.
2 The detach function is supported only by a
combination of the CNC software and servo
software indicated above. When CNC software and
servo software not listed above are used, the pole
position detection function and detach function
cannot be used at the same time.
When the detach function is used, the relationship of the Z phase of

the detector with the pole position of the motor may vary. So, pole
position detection needs to be performed again or the AMR offset (No.
2139) needs to be rewritten to a proper value. To perform pole
position detection again and rewrite the AMR offset, however, the
conventional specification requires that the power be turned off then
back on. With the servo software and CNC software listed above, the
power to the CNC need not be turned off then back on to perform pole
position detection again and rewrite the AMR offset.
- 379 -
When detaching an axis to which pole position detection is applied,

use the procedure below.
• Start detach operation with Gn124 or bit 7 of parameter No. 12.

(Pole position detection completion signal Fn159=0)
• Rewrite the AMR offset (No. 2139) to a proper value manually
or by using G10(*1)
• Cancel detach operation.
• Pole position detection request alarm DS0650 is issued(*2).
• If an absolute detector is used and the AMR offset value is other
than 0, the alarm can be canceled by a reset to enable operation
(pole position detection completion signal Fn159=1).
• If an absolute detector is used and the AMR offset value is 0, the
alarm can be canceled by a reset after executing pole position
detection to enable operation (pole position detection completion
signal Fn159=0 changed to Fn159=1 after pole position detection
completion).
• If an incremental detector is used, the alarm can be canceled after
pole position detection to enable operation (pole position
detection completion signal Fn159=0 changed to Fn159=1 after
pole position detection completion).
*1 : By setting bit 0 of No. 1809 to 1, the servo ready signal SA

can be turned off when pole position detection is not
completed.
*2 : By setting bit 1 of No. 1809 to 1, alarm display can be
disabled even when pole position detection is not
completed.
If the AMR offset is rewritten not during detach operation, a

power-off request is issued. When performing pole position detection
with an absolute detector after cancellation of detach operation, set the
AMR offset value to 0.
- 380 -
Procedure (4) can be used to set parameters according to the cooling

method used for synchronous built-in servo motors.
In the case of no cooling, the parameters are set by initialization
according to procedure (1), so that the parameters need not be
modified.
In the case of liquid cooling only, modify the parameters according to
Table 4.15.1 (p) and Table 4.15.1 (q).

2062 (FS30i, 16i)

2063 (FS30i, 16i)
1893 (FS15i) OVC alarm parameter (POVCLMT)

2065 (FS30i, 16i)
1979 (FS15i) Current rating parameter (RTCURR)

2086 (FS30i, 16i)
1784 (FS15i) OVC magnification in stop state (OVCSTP)

2161 (FS30i, 16i)
CAUTION
If the correct values corresponding to the cooling
method are not set in the parameters above,
expected thermal protection cannot be provided.
Use care.
Table 4.15.1 (p) Setting OVC and current rating parameters by cooling method [200V driving]
Rated POVC1 POVC2 POVCLMT RTCURR OVCSTP
Model Cooling method
[Nm] (N2062) (N2063) (N2065) (N2086) (N2161)
No cooling 6 32689 988 2826 1237 0
DiS22/600
Liquid cooling 10 32523 3069 8170 2104 0
No cooling 17 32683 1069 3172 1310 0
DiS85/400
Liquid cooling 35 32427 4258 12689 2621 0
No cooling －－－－－－
DiS85/1000
Liquid cooling 40 32346 5276 15735 2919 0
No cooling 25 32682 1069 3173 1310 0
DiS110/300
Liquid cooling 45 32427 4260 12694 2621 0
DiS110/1000
Liquid cooling 53 32434 4174 12437 2595 0
No cooling 55 32682 1069 3173 1310 0
DiS260/300
Liquid cooling 105 32427 4260 12694 2621 0
No cooling 55 32679 1111 1710 963 0
DiS260/600
Liquid cooling 105 32360 5100 6848 1926 102
- 381 -
Table 4.15.1 (p) Setting OVC and current rating parameters by cooling method [200V driving]
[Nm] (N2062) (N2063) (N2065) (N2086) (N2161)
DiS260/1000
Liquid cooling 95 32580 2354 6423 1865 0
No cooling 75 32705 782 2322 1121 0
DiS370/300
Liquid cooling 150 32518 3121 9287 2242 0
No cooling 240 32677 1113 1940 1028 0
DiS1200/250
Liquid cooling 480 32352 5196 7743 2033 107
No cooling 300 32682 1069 3173 1310 0
DiS1500/200
Liquid cooling 600 32427 4259 12692 2621 162
No cooling 375 32682 1069 3173 1310 0
DiS2100/150
Liquid cooling 750 32427 4259 12693 2621 162
No cooling 500 32682 1069 3173 1310 0
DiS3000/150
Liquid cooling 1000 32427 4259 12693 2621 162
Table 4.15.1 (q) Setting OVC and current rating parameters by cooling method [400V driving]
[Nm] (N2062) (N2063) (N2065) (N2086) (N2161)
No cooling 6 32689 988 2826 1237 0
DiS22/600
Liquid cooling 10 32523 3069 8170 2104 0
No cooling 17 32683 1069 3172 1310 0
DiS85/400
Liquid cooling 35 32427 4258 12689 2621 0
No cooling 25 32682 1069 3173 1310 0
DiS110/300
Liquid cooling 45 32427 4260 12694 2621 0
No cooling 55 32682 1069 3173 1310 0
DiS260/300
Liquid cooling 105 32427 4260 12694 2621 0
No cooling 55 32679 1111 1351 856 0
DiS260/600
Liquid cooling 105 32360 5095 5406 1712 0
No cooling 75 32705 782 2322 1121 0
DiS370/300
Liquid cooling 150 32518 3121 9287 2242 0
No cooling 240 32678 1130 1529 914 0
DiS1200/250
Liquid cooling 480 32352 5196 6118 1807 0
No cooling 300 32700 845 2507 1165 0
DiS1500/200
Liquid cooling 600 32498 3369 10029 2330 109
No cooling 420 32682 1069 3173 1310 0
DiS2100/150
Liquid cooling 840 32427 4259 12693 2621 122
No cooling 600 32682 1069 3173 1310 0
DiS3000/150
Liquid cooling 1200 32427 4259 12693 2621 122
4.15.2 Detection of an Overheat Alarm by Servo Software when a

Synchronous Built-in Servo Motor are Used
For this subsection, see Subsection 4.14.2, "Detection of an Overheat
Alarm by Servo Software when a Linear Motor and a Synchronous
Built-in Servo Motor are Used".
- 382 -
4.15.3 Smoothing Compensation for Synchronous Built-in Servo

Motor
(1) Overview
Smoothing compensation for synchronous built-in servo motor is a
function used to improve the feed smoothness of a synchronous
built-in servo motor by applying, to the current command, a sine wave
compensation torque 1.5 times and 3 times per pole pair. By setting a
compensation gain and phase with parameters for each component, a
compensation torque matching each motor can be obtained. A value to
be set in a parameter for compensation is automatically calculated
using SERVO GUIDE.
Compensation torque
Activating phase angle θ
command
A1, A2: Amplitude of compensation torque A1sin (1.5θ+P1)
command of sine wave with 1/1.5 and + A2sin (3θ+P2)
1/3 periods
P1, P2: Phase of compensation torque

command of sine wave with 1/1.5 and
1/3 periods
+
+
velocity loop Current loop
Synchronous built-in servo motor
αiCZ sensor
NOTE
This function is supported only when an encoder
that uses 8,000,000 pulses/rev or below for
parameter setting (such as RCN223 and RCN727
manufactured by HEIDENHAIN) is used.

(Series 30i, 31i, 32i,)
(Series 15i, 16i, 18i, 21i, Power Mate i)
(Series 0i-C)
- 383 -

#7 #6 #5 #4 #3 #2 #1 #0
2713 (FS15i) DD
2300 (FS30i, 16i)
DD(#2) Synchronous built-in servo motor is:
0: Disabled.
1: Enabled. (Smoothing compensation for synchronous built-in
servo motor is also enabled.)
2790 (FS15i) Smoothing compensation performed 1.5 times per pole pair
2793 (FS15i) Smoothing compensation performed three times per pole pair
Setting the correction gain of the following parameters with a nonzero
value can switch between the negative direction smoothing
compensation and the positive direction smoothing compensation. In
this case, the smoothing compensation parameter explained above
applies only to feeding in the positive direction.
2791 (FS15i) Smoothing compensation performed 1.5 times per pole pair (negative direction)
2794 (FS15i) Smoothing compensation performed three times per pole pair (negative direction)
An optimal value varies from one motor to another (not from one
motor model to another). So, compensation parameters need to be
determined for each assembled motor. A torque command variation
generated when the motor is fed at low speed is dependent on the
position. The application of smoothing compensation cancels this
position-dependent characteristic, allowing the motor to move
smoothly.
The measuring instruments that can be used to determine these

parameters include "SERVO GUIDE" (Ver. 3.20 or later).
By using SERVO GUIDE (Ver. 3.20 or later), these parameters can be
determined easily. Follow the procedure below to measure the
activating phase and torque command, which are required to
determine the compensation parameters.
- 384 -
Measurement procedure
<1> Set channels as follows:
Channel 1: Counter for smoothing compensation for synchronous
built-in servo motor
Select the target axis for measurement, and set "ROTDD" as the
data type.
Channel 2: Torque command

Select the target axis for measurement, and set "TCMD" as the
data type.
As the conversion coefficient, set the maximum current of the
amplifier used for the target axis.
<2> With this setting, make bidirectional movements by about ±90

deg at about F (14400/number of poles) deg/min for data
measurement. At the time of data measurement, ensure that all
smoothing compensation values are set to 0. Smoothing
compensation for linear motors may be used. Check this point as
well.
Parameters for synchronous built-in servo motor:
No.2377, No.2378, No.2380, No.2381
Parameters for linear motor:
No.2130, No.2131, No.2132, No.2369, No.2370, No.2371
When making measurements, lower the velocity gain to such an
extent that hunting does not occur.
<3> From the "Tools" menu, select "Linear motor compensation
calculation".
(The shortcut is [Ctrl] + [L].)
- 385 -
<4> Pressing the [ADD] button on the displayed dialog box analyzes
waveform data and registers compensation parameter candidates.
The "2/span" item and "4/span" item correspond to smoothing
compensation performed 1.5 times per pole and smoothing
compensation performed 3 times per pole, respectively. "6/span"
is not used for smoothing compensation for synchronous built-in
servo motor.
<5> The compensation parameters slightly vary depending on the

measurement situation. So, repeat a data measurement and a
press of the [Add] button several times in a similar manner while
keeping the dialog box open. (Up to five candidates can be
registered.)
If the displayed values include an extremely different value,
uncheck the corresponding check box on the leftmost side of the
list so that the value is not taken into account in the final
compensation calculation.
<6> Finally, press the [Calc] button for each of the forward and
backward directions. Then, smoothing compensation parameters
are displayed.
<7> By pressing the [Set param] button, the smoothing compensation
parameters are set in the CNC.
- 386 -
<8> Measure TCMD again to confirm the effect of smoothing

compensation.
Torque command Counter

(TCMD) (ROTDD)
Before smoothing compensation adjustment After smoothing compensation adjustment
(*) For details on the use of SERVO GUIDE, refer to the online help
of SERVO GUIDE.
- 387 -
4.16 SETTING PARAMETERS FOR LARGE SERVO MOTORS
4.16.1 Motor Models and System Configurations

To drive a large servo motor, multiple amplifiers may be used. In this
case, two major amplifier connection configurations are available:
• Configuration that uses torque tandem control
• Configuration that uses a PWM distribution module
Which configuration to use is determined by the motor model used
(Table 4.16.1 (a)).
Table 4.16.1 (a) Motor models and system configurations

Motor model Configuration Number of amplifiers
αiS300/2000 Torque tandem 2
αiS500/2000 configuration (*1)
αiS1000/2000HV
αiS2000/2000HV PWM distribution module 4
αiS3000/2000HV configuration (PDM) (*2)
*1 Even when only two amplifiers are used, a PDM can be
used. By using a PDM, the number of motors connectable to
the CNC may be increased when compared with a case
where the torque tandem configuration is used. Contact
FANUC for details.
*2 PDM stands for PWM Distribution Module.
- 388 -
4.16.2 Setting Parameters in the Torque Tandem Configuration
(1) Overview
For those motors that use the torque tandem configuration described in
Subsection 4.16.1, settings for torque tandem control and for enabling
the feedback copy function need to be made.
NOTE
1 Torque tandem control is an optional function.
2 When a large motor is used in the torque tandem
configuration, two CNC axes are occupied per
motor.
Example of connection)
AMP AMP AMP AMP
(X-axis) (Y1-axis) (Y2-axis) (Z-axis)
Main Sub
CNC
Main
X 000.000 FSSB
Y 000.000
Z 000.000
Power line 2
Power line 1
Pulse coder feedback

(connected to the main axis)
Servo motor (such as αiS1000/2000HV)
- 389 -

NOTE
Servo HRV4 control exercises control on one axis
per CPU, so this configuration cannot be used with
servo HRV4 control.

<1> Of the two amplifiers connected to a motor, assign one amplifier
to the main axis and the other to the sub-axis used for torque
tandem control, and enable torque tandem control.
#7 #6 #5 #4 #3 #2 #1 #0
1817(FS15i) TANDEM
1817(FS30i,16i)
TANDEM(#6) 1: Enables torque tandem control. (Set this parameter for each of
the main axis and sub-axis.)
To make settings related to torque tandem control, see Section 4.21,

"TORQUE TANDEM CONTROL FUNCTION".
<2> Make the parameter setting indicated below for the sub-axis to
enable the feedback sharing function.
The feedback cable from the motor is connected to the amplifier
on the main axis.
#7 #6 #5 #4 #3 #2 #1 #0
1960(FS15i) PFBCPY
2018(FS30i,16i)
PFBCPY(#7) 1: Uses feedback to the main axis for the sub-axis as well. (Set this
parameter only for the sub-axis.)
- 390 -
4.16.3 Setting Parameters in the PWM Distribution Module

Configuration
(1) Overview
The PWM distribution module (PDM) has a function for copying a
PWM command for one axis received from the CNC and distributing
the command copy to multiple servo amplifiers and a function for
finding an average current per servo amplifier from current feedback
signals received from multiple servo amplifiers and transferring the
average current to the CNC. Multiple servo amplifiers connected to a
PDM can be viewed from the CNC as being connected to one axis. So,
by using a PDM, high power can be achieved through parallel driving
without increasing the number of CNC controlled axes.
NOTE
When a PWM distribution module is used, HRV3
needs to be set. So, one FSSB path cannot
connect more than four slaves consisting of
amplifiers and a PDM. (See (4) of Subsection
4.2.1.)
Example of connection)
Recognized as 3 slaves by CNC
AMP PDM AMP

(X-axis) (Y-axis) (Z-axis)
CNC
Main
X 000.000 FSSB
Y 000.000
Z 000.000
Local AMP AMP AMP AMP

FSSB Slave 1 Slave 2 Slave 3 Slave 4
PWM command for Y-axis is

distributeed to multiple axes.
Current feedback signals from

multiple slaves are averaged by
PDM then fed back to Y-axis.
Power line
Puse coder feedback
Servo motor (such as αiS2000/2000HV)
- 391 -

To use a PDM, the following system software is needed:

B0HA/BDHA/DDHA-17 and subsequent editions (Series
16i/18i/21i-MB)
BDHE-07 and subsequent editions (Series 18i-MB5)
88E1-01 and subsequent editions (Power Mate i-D)
88F2-08 and subsequent editions (Power Mate i-H)
(*) The PDM cannot be used with the Series 15i and Series 30i.

(a) Setting for a PDM
For axes that use a PDM, servo HRV3 control needs to be set. Set the
parameters below.
Set the parameter for servo HRV2 control beforehand. Next, set the
parameter below for servo HRV3 control (HR3=1).(For each axis)
#7 #6 #5 #4 #3 #2 #1 #0
2013 (FS16i) HR3
* When using a PDM, set HR3=1. In actual operation, this control
is equivalent to HRV2 control. (The G5.4-based high-speed
current control mode cannot be switched either.)
For those axes that uses a PDM, set the following parameter in
addition to the setting of HR3 above:
2165 (FS16i) Set 0.
If this parameter is not set, "Invalid motor/amplifier combination" may
be issued.
Note that because this parameter needs to be set to 0 when a PDM is
used, the servo tuning screen does not provide an actual current
indication (ampere indication). (A % indication is provided.)
- 392 -
(b) Setting for a 16-pole servo motor

For an axis on which any of the servo motors listed below is used, set
the parameters for using a 16-pole servo motor.
Servo motor name Motor specification
αiS2000/2000HV 0091
αiS3000/2000HV 0092
#7 #6 #5 #4 #3 #2 #1 #0
2220 (FS16i) P16
P16(#5) 0: Does not use a 16-pole servo motor.
1: Uses a 16-pole servo motor.
#7 #6 #5 #4 #3 #2 #1 #0
AMR0 to 6 (#0 to #6) Set the AMR value corresponding to the number of motor poles.
AMR
Number of motor poles
6 5 4 3 2 1 0
16-pole servo motor
0 0 0 1 0 0 0
αiS2000/2000HV, αiS3000/2000HV
Other than 16-pole servo motors (8-pole
0 0 0 0 0 0 0
motor)
- 393 -
4.16.4 Data Measurement and Diagnosis with a PWM Distribution

Module (PDM)
(1) Overview
In a configuration that uses a PWM distribution module, many motor
power lines are used. If an error occurs, error location isolation may
be difficult in some cases. To facilitate troubleshooting, the following
functions are available:
(a) PDM current monitor

- The actual current flowing through each amplifier is
monitored using SERVO GUIDE.
(b) PDM's slave ready output
- The ready state of each amplifier present when the
VRDY-OFF alarm is issued is displayed on the diagnosis
screen of the CNC.
For the method of PDM-based troubleshooting, refer to

"Troubleshooting of Large Servo Motors by Using a PDM (PWM
Distribution Module) (A-72562-034)" as well.

The PDM diagnosis functions are available with the following series
and editions:
Applicable servo Applicable

Applicable PDM
Function software series and SERVO GUIDE
version(*)
edition version
PDM current Series 90B1/F(06) or Overall version C Ver 3.20
monitor function later or later
PDM's slave ready Series 90B1/G(07) or Overall version C -
output later or later
* The overall version of a PDM can be checked with the indication

provided on the label of the PDM.
PDM unit Specification No.

Example of label indication
PDM
TYPE A06B-6135-H001 C
No． V05X12345
FANUC LTD
Overall version indication

(One letter)
↓Front
- 394 -
(3) PDM-related functions

(a) PDM current monitor function
By using SERVO GUIDE, the actual current of each amplifier
connected to a PDM can be measured.
• Method of setting SERVO GUIDE

From "Type", select a type of current to be measured. (Counting from
the closest to the PDM of the amplifiers connected to the local FSSB,
the R phase current of the n-th amplifier is represented as IRn and the
S phase current of the n-th amplifier is represented as ISn.)
Example)
When the R phase current (IR) of slave 1
NOTE
The update interval of this data is 1 msec.
- 395 -
[Example of waveform measurement]

R phase
(b) PDM's slave ready output

With an axis that uses a PDM, the VRDY-OFF alarm is issued if there
is one or more servo amplifiers that are connected to the PDM and are
not placed in the ready state. To facilitate troubleshooting in such a
case, the ready state of each amplifier present when the VRDY-OFF
alarm is issued is displayed on the diagnosis screen of the CNC.
• Setting parameters
By setting the parameters below, the ready state of each amplifier
present when the VRDY-OFF alarm is issued can be displayed on
diagnosis No. 353. Note that the values to be set in the parameters
vary, depending on whether an odd number or even number is set in
parameter No. 1023 for the axis.
When an odd number When an even

Parameter No. to be
is set in No. 1023 for number is set in No.
set
the axis 1023 for the axis
No. 2115 0 0
No. 2151 3094 3222
- 396 -
• Diagnosis screen display
Diagnosis No. Amplifier ready state when the VRDY-OFF alarm is issued (in
353 decimal)
By checking the decimal value displayed in diagnosis No. 353, the

amplifier that caused the VRDY-OFF alarm to be issued can be
identified. (See the table below.)
Value displayed Ready state of each slave amplifier

by diagnosis (○: Ready state, ×: Not-ready state)
No. 353 Slave 1 Slave 2 Slave 3 Slave 4
0 ○ ○ ○ ○
1 × ○ ○ ○
2 ○ × ○ ○
3 × × ○ ○
4 ○ ○ × ○
5 × ○ × ○
6 ○ × × ○
7 × × × ○
8 ○ ○ ○ ×
9 × ○ ○ ×
10 ○ × ○ ×
11 × × ○ ×
12 ○ ○ × ×
13 × ○ × ×
14 ○ × × ×
15 × × × ×
- 397 -
4.17 INTERACTIVE FORCE COMPENSATION FUNCTION
(1) Overview
If a rotary axis with an eccentric load is located on a linear axis, an
interactive force such as a centrifugal force or reaction force due to
acceleration/deceleration is applied to the linear axis when a motion is
made on the rotary axis. Similarly, an interactive force is applied to
the rotary axis due to acceleration/deceleration on the linear axis.
The interactive force compensation function is a servo function that
achieves more accurate position control by canceling the influence of
those interactive forces through software-based compensation. This
function is useful for enabling machine tools such as 5-axis machine
tools to perform higher-speed and higher-precision machining.
• When a constant-speed rotation is made on a rotary axis

Eccentric load Centrifugal force
Interactive force
in linear axis
Rotary axis Linear axis
• When acceleration is performed on a rotary axis

Acceleration Eccentric load
Interactive force in
Reaction against
linear axis direction
acceleration
Rotary axis Interactive Linear axis

force in rotary
axis direction
• When acceleration is performed on a linear axis

Eccentric load
Inertial force
Acceleration
Rotary axis Linear axis
- 398 -

To use the interactive force compensation function, the system
software below is needed.
Edition 23.0 or subsequent editions of the following series (CNCs not
employing the remote option system)
Series 30i-A : G002,G012,G022,G032
Series 31i-A : G101,G111
Series 31i -A5 : G121,G131
Series 32i-A : G201
Edition 06.0 or subsequent editions of the following series (CNCs
employing the remote option system):
Series 30i-A : G003,G013,G023,G033
Series 31i-A : G103,G113
Series 31i -A5 : G123,G133
Series 32i-A : G203
(3) Axis configuration for the interactive force compensation function

(a) Target axis configuration
The interactive force compensation function basically assumes the two
axis configurations described below.
• Configuration 1: Rotary table (C-axis) on a linear axis (X-axis)
Configuration where an eccentric rotary axis is mounted on a
linear axis and the center axis of the rotary axis is normal to the
linear axis (When the two axes are parallel with each other, no
interactive force occurs.)
Eccentric load
C-axis
X-axis
• Configuration 2: Rotary table (C-axis) on a rotary axis (A-axis)

Configuration where an eccentric rotary axis is mounted on a
rotary axis and the center axis of the eccentric rotary axis is
normal to the center axis of the rotary axis on which the eccentric
rotary axis is mounted
Eccentric load
C-axis
A-axis
- 399 -
(b) Axis naming in interactive force compensation

With the interactive force compensation function, an axis that
produces an interactive force when a movement is made on the axis is
named a moving axis, and an axis affected by such an interactive
force (an axis to which interactive force compensation is applied) is
named a compensated axis.
In configuration 1, for example, suppose that an interactive force acts

on the rotary axis due to acceleration operation on the linear axis. In
such a case, the linear axis is referred to as the moving axis, and the
rotary axis is referred to as the compensated axis.
Conversely, suppose that an interactive force acts on the linear axis
due to rotation on the rotary axis. In such a case, the rotary axis is
referred to as the moving axis, and the linear axis is referred to as the
compensated axis.
(c) Axis configuration

For one compensated axis, up to two moving axes can be specified
(interactive force applied from two axes onto one axis can be
compensated for simultaneously). Of two specifiable moving axes, the
first one is referred to as the first moving axis, and the second one is
referred to as the second moving axis.
Bidirectional compensation is applicable between two axes.
An axis to which torque tandem control or synchronous control is
applied can be set as a moving axis or compensated axis.
When servo axis numbers are divided into groups each consisting of 8
successive axes (or 4 successive axes for Series 90D0), the servo axis
number of a moving axis and the servo axis number of the
corresponding compensated axis need to exist in the same group.
When a servo axis number (No. 1023) is represented in the following
format, set servo axis numbers so that n for a moving axis matches n
for the corresponding compensated axis.
For series 90D0: Servo axis number = 4n+k

(where, n is an integer, and k = 1 ,2, 3, 4)
No.1023=1,2,3,4 5,6,7,8 9, . . .
The servo axis numbers in one group (enclosed in a dashed frame) can be used to specify a
combination of moving axes and a compensated axis.
For series 90E0: Servo axis number = 8n+k

(where n is an integer, and k = 1, 2, 3, 4, 5, 6, 7, 8)
No.1023=1,2,3,4,5,6,7,8 9,10,11,12,13,14,15,16 17, . . .
- 400 -
(d) Notes
To use the interactive force compensation function, feed-forward
must be enabled. While feed-forward is disabled for a moving axis,
interactive force is disabled.
When no direct connection is made between a moving axis and
compensated axis, the interactive force compensation function cannot
be used.

The function of each parameter is described below.
* For an example of parameter setting, see "(5) Example of

parameter setting".
* A compensation value used with the interactive force
compensation function is calculated on the compensated axis side.
So, parameters for setting a compensation gain, angle data offset
value, and so forth are to be set on the compensated axis side.
#7 #6 #5 #4 #3 #2 #1 #0
2292(FS30i) MOVAXS MV1IFC MV1ID2 MV1ID1 MV1ID0 IFC1ON C1TYP1 C1TYP0
MOVAXS(#7) Specifies whether the axis is a moving axis used with the interactive
Set with moving axis force compensation function. (Power-off parameter)
0: The axis is not a moving axis.
1: The axis is a moving axis.
For an axis used with the interactive force compensation function as a
moving axis (axis that affects another axis), set this bit parameter to
1.
MV1IFC(#6) Sets calculation of interactive force from the first moving axis.
Set with compensated axis (Power-off parameter)
0: Disables calculation of interactive force from the first moving
axis.
1: Enables calculation of interactive force from the first moving
axis.
When this bit parameter is set to 1, interactive force from the first
moving axis is calculated. (However, when position feed-forward for
the first moving axis is disabled, the calculated value of interactive
force is 0.)
This bit parameter specifies interactive force calculation alone. To
enable interactive force compensation actually, IFC1ON (bit 2 of No.
2292) needs to be set as well.
- 401 -
MV1ID2,MV1ID1,MV1ID0(#5,4,3) Specifies a servo axis number for the first moving axis.
Set with compensated axis For calculation of interactive force from the first moving axis (bit 6 of
No. 2292=1), a servo axis number needs to be specified for the first
moving axis. Set these bit parameters to values below according to a
desired servo axis number.
Servo axis Servo axis
number for number for
MV1ID2 MV1ID1 MV1ID0
moving axis moving axis
(Series 90E0) (Series 90D0)
0 0 0 8n+1 4n+1
0 0 1 8n+2 4n+2
0 1 0 8n+3 4n+3
0 1 1 8n+4 4n+4
1 0 0 8n+5
1 0 1 8n+6
1 1 0 8n+7
1 1 1 8n+8
* n = 0, 1, 2, ...
NOTE
When the interactive force compensation function
is used, a restriction is imposed on selection of a
moving axis and compensated axis. When a servo
axis number (No. 1023) is represented in the
format below, select a moving axis and
compensated axis from those axes that have the
same n value.
Series 90D0: Servo axis number = 4n+k (where,
n is an integer, and k = 1, 2, 3, 4)
Series 90E0: Servo axis number = 8n+k (where
n is an integer, and k = 1, 2, 3, 4, 5, 6, 7, 8)
If the n value of a moving axis and the n value of a
compensated axis differ from each other, modify
the servo axis number setting so that the two n
values match.
IFC1ON(#2) Turns on/off the compensation function for interactive force from the
Set with compensated axis first moving axis.
0: Does not compensate for interactive force from the first moving
axis.
1: Compensates for interactive force from the first moving axis.
By setting this bit parameter to 1, compensation for interactive force
from the first moving axis is enabled. (However, bit 6 (MV1IFC) of
No. 2292 must be set to 1.)
- 402 -
C1TYP1,C1TYP0(#1,0) Sets a compensation type (for the first moving axis).

Set with compensated axis
Set a compensation type according to the axis configuration and axis
type to which the interactive force compensation function is applied.
An example of axis configuration is provided below.
Compensation
Axis configuration C1TYP1 C1TYP0
type
Interactive force from linear axis to
0 0 Type L
rotary axis
Interactive force from rotary axis
0 1 Type R
to linear axis
• Configuration 1: Rotary axis (C-axis) on a linear axis (X-axis)

Eccentric load
C-axis
X-axis
When the C-axis is a compensated axis

→ Type L (Bits 1, 0 of No. 2292=0,0)
When the X-axis is a compensated axis
→ Type R (Bits 1, 0 of No. 2292=0,1
• Configuration 2: Rotary axis (C-axis) on a rotary axis (A-axis)
Eccentric load
A-axis C-axis
When the C-axis is a compensated axis

→ Type L (Bits 1, 0 of No. 2292=0,0)
When the A-axis is a compensated axis
→ Type R (Bits 1, 0 of No. 2292=0,1)
#7 #6 #5 #4 #3 #2 #1 #0
2293(FS30i) MV2IFC MV2ID2 MV2ID1 MV2ID0 IFC2ON C2TYP1 C2TYP0
MV2IFC(#6) Sets calculation of interactive force from the second moving axis.
Set with compensated axis (Power-off parameter)
0: Disables calculation of interactive force from the second moving
axis.
1: Enables calculation of interactive force from the second moving
axis.
- 403 -
MV2ID2,MV2ID1,MV2ID0(#5,4,3) Specifies a servo axis number for the second moving axis.
Servo axis Servo axis
number for number for
MV2ID2 MV2ID1 MV2ID0
moving axis moving axis
(Series 90E0) (Series 90D0)
0 0 0 8n+1 4n+1
0 0 1 8n+2 4n+2
0 1 0 8n+3 4n+3
0 1 1 8n+4 4n+4
1 0 0 8n+5
1 0 1 8n+6
1 1 0 8n+7
1 1 1 8n+8
* n = 0, 1, 2, ...
Set with compensated axis second moving axis.
0: Does not compensate for interactive force from the second
moving axis.
1: Compensates for interactive force from the second moving axis.
C2TYP1,C2TYP0(#1,0) Sets a compensation type (for the second moving axis).

Set with compensated axis Axis configuration C2TYP1 C2TYP0 Compensation type
Interactive force from
0 0 Type L
linear axis to rotary axis
Interactive force from
0 1 Type R
rotary axis to linear axis
2478(FS30i) Interactive force compensation: Compensation gain (for the first moving axis)
[Unit of data] -
Set a coefficient (gain) for interactive force compensation.
The optimum value varies according to the weight of an eccentric load
and the distance from the rotation center. So, set a proper value
according to "(6) Setting parameters".
2479(FS30i) Interactive force compensation: Angle data offset (for the first moving axis)
[Unit of data] 360/4096 deg
Set angle data that can be read when an eccentric load is placed at the
reference position of the rotary axis. The parameter setting varies,
depending on the compensation type as follows:
Compensation type L → An offset relative to the angle data of the

compensated axis is set with the compensated axis.
- 404 -
Compensation type R → An offset relative to the angle data of the

moving axis is set with the compensated axis.
2480(FS30i) Interactive force compensation: Compensation gain (for the second moving axis)
2481(FS30i) Interactive force compensation: Angle data offset (for the second moving axis)
For a rotary axis, the number of pulses per revolution output from a
detector needs to be set.
2455(FS30i) Integer part of the number of pulses per revolution (α)

2456(FS30i) Exponent part of the number of pulses per revolution (β)

Set with rotary axis
From the number of feedback pulses per revolution on a rotary axis,
find the values of the integers (α and β) that satisfy the expression
below then set the found values in the parameters above.
Number of pulses per revolution on a rotary axis = α×2β

(where, 1≤α≤32767, 0≤β≤12)
An example of parameter setting is provided below using a detector
indicated below for a synchronous built-in servo motor.
Detector No.2455 No.2456 Remarks
αiCZ 512A 8192 7 Manufactured by FANUC
αiCZ 768A 12288 7 Manufactured by FANUC
αiCZ 1024S 16384 7 Manufactured by FANUC
RCN223 16384 10 Manufactured by HEIDENHAIN
- 405 -

To use the interactive force compensation function, an axis (moving
axis) that produces an interactive force by movement on the axis and
an axis (compensated axis) that is affected by the interactive force
need to be set, and the relationship between the two axes needs to be
set properly according to the machine configuration. This example
explains the parameters for axis setting.
As an example, suppose a machine with the following axis

configuration: X-axis
C-axis
Y-axis
• Assume a configuration where the X-axis (linear axis) is placed

on the Y-axis (linear axis), the C-axis (rotary axis) is placed on
the X-axis, and an eccentric load is mounted on the C-axis.
• Suppose that a synchronous built-in servo motor is used for the
C-axis and that the detector αiCZ1024A is used.
• Suppose also that the servo axis numbers (No. 1023) and
detection units indicated below are used for the axes. (Use of
servo software Series 90E0 is assumed.)
Axis No.1023 Detection unit Remarks
X-axis 1 1 µm Linear axis
Y-axis 2 1 µm Linear axis
C-axis 6 0.001 deg Rotary axis
• Suppose that the X-axis and Y-axis cross each other at right
angles and that no interactive force occurs between the X-axis
and Y-axis.
• This example simultaneously compensates for an interactive
force that is produced by rotation on the C-axis and acts on the
X-axis and Y-axis and also compensates for an interactive force
that is produced by acceleration on the X-axis and Y-axis and
acts on the C-axis.
Compensated axis: Interactive force First moving axis: C-axis Movement on

X-axis Second moving axis: - rotary axis
Compensated axis:
Y-axis
- 406 -
Compensated axis: Interactive force First moving axis: X-axis Movement

C-axis Second moving axis: Y-axis on linear
axes
(Parameter setting)
Setting
No. Description
X-axis Y-axis C-axis
No.2292#7 Moving axis specification 1 *1 1 *1 1 *1
No.2455 Integer part of the number of pulses 0 0 16384
No.2456 Exponent part of the number of pulses 0 0 7 *2
Calculation of interactive force from the first 1 1 1
No.2292#6 *3
moving axis
Servo axis number specification for the first 101 101
No.2292#5,4,3 000
moving axis
Enabling compensation for interactive force 1 1 1
No.2292#2
from the first moving axis
*4
Type of compensation for interactive force 01 01
No.2292#1,0 00
from the first moving axis
Compensation gain for interactive force from Adjusted value Adjusted value
No.2478 Adjusted value
the first moving axis
No.2479 Angle data offset for the first moving axis Adjusted value Adjusted value Adjusted value
Calculation of interactive force from the 0 0 1
No.2293#6
second moving axis
Servo axis number specification for the - - 001
No.2293#5,4,3 *5
second moving axis
Enabling compensation for interactive force - -
No.2293#2 1
from the second moving axis
Type of compensation for interactive force - -
No.2293#1,0 00
from the second moving axis
Compensation gain for interactive force from - -
No.2480 Adjusted value
the second moving axis
No.2481 Angle data offset for the second moving axis - - Adjusted value
*1) All axes are moving axes. So, set bit 7 of No. 2292 to 1 for all
axes.
*2) The X-axis and Y-axis are linear axes. So, set 0 as the number of
pulses per revolution. The C-axis is a rotary axis, so the number
of pulses per revolution needs to be set. When using αiCZ
1024A, set 16384 in No. 2455, and set 7 in No. 2456.
*3) Considering the C-axis as the first moving axis for the X-axis
and Y-axis, set the C-axis as the first moving axis for the Ｘ-axis
and Y-axis. Moreover, considering the X-axis as the first moving
axis for the C-axis, set the X-axis as the first moving axis for the
C-axis.
*4) The linear axes (X-axis and Y-axis) are affected by an interactive
force from the rotary axis (C-axis). So, set type R for the X-axis
and Y-axis.
The rotary axis (C-axis) is affected by an interactive force from
the linear axes (X-axis and Y-axis). So, set type L for the C-axis.
*5) Considering the Y-axis as the second moving axis for the C-axis,
set the Y-axis as the second moving axis for the C-axis.
- 407 -

For interactive force compensation, two parameters, one for angle data
offset and the other for compensation gain, need to be adjusted. The
method of adjustment is described below.
NOTE
To use the interactive force compensation function,
Various parameters need to be set. Before starting
parameter adjustment, Set bit 2 of No. 2292 to 0
and set bit 2 of No. 2293 to 0 (to disable
interactive force compensation). If these bit
parameters are set to 0, interactive force
compensation is not actually enabled but
calculated compensation data can be observed. At
the initial stage of adjustment, disable
compensation.
(a) Checking the angle data of a rotary axis

When a rotary axis is to be set as a compensated axis or moving axis,
the angle data of the rotary axis is required. Check that the number of
pulses per revolution (No. 2455 and No. 2456) is set correctly and the
angle data is calculated correctly. For all rotary axes that are used for
interactive force compensation, check that phase data is output
correctly, by using the method described below.
• Check method
By making a movement on a rotary axis by a certain amount,
observe the change in angle data. If the number of pulses per
revolution is set correctly, the angle data changes by 4096 when
a movement is made on the rotary axis by 360°. Check whether
the actual amount of movement matches the change in phase
data.
For example, check that when a movement of 90° is made on a
rotary axis, the change in phase data is 1024 (= 4096×90/360).
If the actual amount of movement does not match the change in
phase data, recheck the settings of No. 2455 and No. 2456.
(Parameter setting for observing angle data with diagnosis No. 353)
By setting the following parameters, angle data can be observed with
diagnosis No. 353:
Series 90D0 Series 90E0

No. 2151 No. 2115
No. 1023 No. 1023
2n+1 4n+1 5916 0
2n+2 4n+2 6044 0
4n+3 12060 0
4n+4 12188 0
- 408 -
(b) Setting angle data (No. 2479 and No. 2481)

Move the eccentric load on a rotary axis to the reference position
shown below and observe the value of phase data. Set the observed
value in the angle data parameter (No. 2479 or No. 2481).
Linear axis (positive

Reference position
direction)
Rotary table
If the eccentric load cannot be moved to the reference position, find a

value by estimation from the angle data at a position to which the
eccentric load can be moved.
For example, if a phase data of 2000 is observed when the eccentric
load is moved to a position of 90° away from the reference position,
the value to be set as angle data is:
2000−4096×90/360 = 976
(If the result of calculation is a negative value, add 4096 to the result
to make a value from 0 to 4095.)
If the accurate position of the eccentric load is unknown, set an
approximate position with the method above then make a fine
adjustment according to "(c) Adjusting compensation gain" below.
(c) Adjusting compensation gain (No. 2478 and No. 2480)

The method of compensation gain adjustment is described below.
The example described below uses a rotary table as a moving axis and
uses a linear axis as a compensated axis in configuration 1, and uses a
waveform produced by making reciprocating motions in the arrow
directions. It is supposed that each reciprocating motion is made by
270° through the reference position.
B Reciprocating
motion
Linear axis
C (positive
direction)
D
- 409 -
NOTE
The magnitude of interactive force varies,
depending on the position (angle) of an eccentric
load on the rotary table. Depending on the position
of an eccentric load, no interactive force is
produced. So, when making a compensation gain
adjustment, make a check by making movements
fully across the movable range on the rotary axis.
• If acceleration/deceleration is performed on the
linear axis in the left-hand figure, no interactive
force is produced on the rotary axis at positions
A and C.
• At positions A and C, acceleration/deceleration
performed on the rotary axis produces no
interactive force on the linear axis. However,
interactive force due to centrifugal force is
produced.
• At positions B and D, interactive force due to the
centrifugal force of the rotary axis is not
produced on the linear axis. However,
interactive force due to acceleration/deceleration
is produced.
<1> Checking the influence of interactive force

While making no movement on the compensated axis to which
the interactive force compensation function is applied, make a
movement on the moving axis. At this time, observe the
waveform of the torque command (TCMD) and position
feedback (POSF) on the compensated axis with SERVO GUIDE.
Interactive force due to centrifugal force
Moving axis POSF
Compensated axis
TCMD
Compensated axis
POSF
Interactive force due to acc./dec.
The position on the compensated axis varies, depending on movement on the moving axis.
- 410 -
<2> Checking interactive force compensation data

When interactive force compensation is disabled (bit 2 of No.
2292=0, bit 2 of No. 2293=0), adjust the compensation gain (No.
2478, No. 2480).
A torque command change occurring on the compensated axis
according to a movement on the moving axis is considered to be
a torque produced to cancel the influence of interactive force.
Accordingly, the torque command waveform observed at this
time is about equal to the interactive force. So, observe the
torque command and interactive force compensation data on the
compensation axis present when a movement is made on the
moving axis (IFCMP1 for the first moving axis/IFCMP2 for the
second moving axis), and adjust the compensation gain so that
the torque command approximately matches the compensation
data.
See the next item for the setting of SERVO GUIDE for
observing interactive force compensation data.
Compensated axis
TCMD
Compensation data
(IFCMPx)
If the accurate position of the eccentric load cannot be identified

in angle data adjustment of item (b), gain adjustment alone may
not produce a waveform match. Make a fine adjustment of the
angle data offset (No. 2479, No. 2481).
- 411 -
Compensated axis
TCMD
Compensation data
(IFCMPx)
The timing of a maximum interactive force due to centrifugal force

matches, so the angle data offset is considered to be adjusted
correctly.
NOTE
1 Be sure to enable feed-forward.
2 When the motor rotation direction of a
compensated axis (No. 2022) is set to -111 (CW
direction), the polarity of compensation data is
opposite to that of the torque command. So, make
an adjustment so that IFCMPx is TCMD inverted
upside down.
• SERVO GUIDE channel setting (Interactive force

compensation data: IFCMP1, IFCMP2)
Axis : Select a target compensated axis.

Kind : Select IFCMP1 or IFCMP2.
Unit : Select %.
Conv. Coef : Set 100.
Conv. Base : Set 29128.
Origin value : Set 0.
- 412 -
• When SERVO GUIDE does not support IFCMP1 and

IFCMP2
Axis : Select a target compensated axis.
Type : Select TCMD.
Unit : Select %.
Conversion coefficient : Set 100.
Conversion reference : Set 29128.
Origin value : Set 0.
Extended address : Set the value corresponding to the
servo axis number of a
compensated axis according to the
table below.
Extended Extended
Series 90D0 Series 90E0
address address
No. 1023 No. 1023
(IFCMP1) (IFCMP2)
2n+1 4n+1 5923 5931
2n+2 4n+2 6051 6059
4n+3 12607 12615
4n+4 12195 12203
Shift : Set 0.
<3> Checking the effect of interactive force compensation

After adjusting the compensation gain parameter, enable the
interactive force compensation function (First moving axis: Bit 2
of No. 2292=1, Second moving axis: Bit 2 of No. 2293=1) then
observe the waveform of position feedback (POSF) on the
compensated axis.
Check that when a movement is made on the moving axis, the
change in position feedback is reduced.
Make a fine adjustment of the compensation gain parameter so
that the change in position feedback is minimized.
• Without compensation (Bit 2 of No. 2292=0)
Moving axis POSF
Compensated axis
TCMD
Compensated axis
POSF
- 413 -
• With compensation (Bit 2 of No. 2292=1)
Moving axis POSF
Compensated axis
TCMD
Compensated axis
POSF
The change in position on the compensated axis is

improved.
- 414 -
4.18 TORQUE CONTROL FUNCTION
(1) Overview
In PMC axis control, the torque control function can be used. The
servo motor produces a torque as specified by the NC. Note that the
user can switch between position control and torque control.
(2) Control types

Two types of torque control are supported: type 1 and type 2. The two
types are explained below.
(i) Torque control type 1

The motor produces a torque according to a torque command
specified by the PMC. A servo alarm is issued if the speed of the
motor exceeds the excessive speed alarm level specified by the
PMC.
A block diagram of torque control type 1 is shown below.
PMC Servo
Torque
command
Actual
Maximum speed
Speed
allowable speed
monitoring
Excessive speed
alarm
Fig. 4.18 (a) Torque control type 1
(ii) Torque control type 2

The motor produces a torque according to a torque command
specified by the PMC.
When the motor is loaded, it produces a torque according to a
torque command. When it is not loaded, it rotates at a constant
(allowable) speed.
PMC Servo
Torque
command
+ Speed Torque
Maximum
allowable speed control limiter
−
Fig. 4.18 (b) Torque control type 2
* Basically, torque control type 2 performs speed control to cause

the limiter to operate on a command from the speed controller
according to a torque command specified by the PMC. This
causes the motor to produce a torque that matches the torque
command when it is loaded and to rotate at a constant (allowable)
speed when it is not loaded.
- 415 -

(Series 15i-B,16i-B,18i-B,21i-B,0i-B,Power Mate i)
(Series 0i-C,20i-B)

This manual describes servo-related parameters only.
NOTE
For details about the setting of the torque control
function for each CNC, refer to "PMC Axis Control"
in the respective CNC Connection Manual
(Function).
#7 #6 #5 #4 #3 #2 #1 #0
1951 (FS15i) FRCAXS
2007 (FS30i, 16i)
FRCAXS (#7) Torque control is:
0: Not used
#7 #6 #5 #4 #3 #2 #1 #0
1743 (FS15i) FRCAX2
2203 (FS30i, 16i)
FRCAX2 (#4) Torque control type 2 is:
0: Not used (Torque control type 1 is used.)
1: Used ← To be set (Usually, use type 2.)
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) PIEN
2003 (FS30i, 16i)
PIEN (#3) The velocity control method to be used is:
0: I-P control
1: PI control ← To be set
- 416 -
1998 (FS15i) Torque constant

2105 (FS30i, 16i)
This parameter is used to specify a motor-specific torque constant.
The units are as follows:
0.00001 N⋅m/(torque command) for a rotary motor
0.001 N⋅m/(torque command) for a linear motor
NOTE
1 When the initial parameter setting function (Sec.
2.1) is used, a motor-specific value is set
automatically.
2 When torque control is set, the following functions
are disabled:
- Velocity loop high cycle management function
- Acceleration feedback function
- 417 -

(POSITION TANDEM) Optional function
(1) Overview
This function suppresses vibration caused by interference between the
master axis and slave axis in position tandem (simple synchronous or
synchronous) control.
NC Servo Disturbance
command +
+ + + Velocity fbm
Position Velocity Kt/Jm⋅s
control control
- +
Master axis Master motor
Velocity fbm
Tandem disturbance elimination control
Velocity fbs
Slave axis Slave motor

- -
Position Velocity Kt/Jm⋅s
control + control + + Velocity fbs
+
Disturbance

(Series 0i-C)
(3) Cautions
• This function is optional. (To enable the position tandem function, the option of axis
synchronous control (FS30i), simple synchronous control (FS16i), or synchronous
control (FS15i) is additionally needed.)
• This function can be used only for two-axis (simple) synchronous control. This
function cannot be used for more than two axes.
• In servo axis arrangement, the main axis must be an odd-numbered axis, and the
sub-axis must be a subsequent even-numbered axis.
• This function cannot be used with a mechanism that allows the mechanical
coupling of two axes to be released.
• Servo HRV4 control exercises one-axis control with one CPU, so that this function
cannot be used together with servo HRV4 control.
- 418 -

Tcmd(M) Velocity fbm
Tandem disturbance
elimination control
2325(M)
Ki 1/s
+ +
Phase
compensation
+ -
Kc 2036(S)
2325(S)
2036(M)
M : Master axis
Tcmd(S) S : Slave axis Velocity fbs
#7 #6 #5 #4 #3 #2 #1 #0
1709 (FS15i) TANDMP
2019 (FS30i, 16i)
(Set this parameter for the master axis only.)
TANDMP (#1) Tandem disturbance elimination control is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1952 (FS15i) VFBAVE
2008 (FS30i, 16i)
VFBAVE (#2) The velocity feedback average function is:
0: Not used.
1: Used.
Usually, set this parameter to 0. The velocity feedback average
function has an effect equivalent to that of tandem disturbance
elimination control for machines that have a certain rigidity. In general,
this function is not used together with tandem disturbance elimination
control. When using this function together with tandem disturbance
elimination control, set integral gain Ki and proportional gain Kc to 0.
* With Series 90B3 and 90B7, a different bit position is assigned,
that is, bit 6 for the slave axis is used.
1721 (FS15i) Proportional gain Kc

2036 (FS30i, 16i)
[Valid data range] 0 to 32767 (0<Kc<0.5)
[Typical setting] 0
This parameter is not used generally, but is used for machines with a
large friction. This parameter has the same function as damping
compensation gain Kc of the tandem control function. (See Subsec.
4.21.2.)
- 419 -
1721 (FS15i) Phase compensation coefficient α

2036 (FS30i, 16i)
(Set this parameter for the slave axis only.)
[Valid data range] 51 to 512 (0.1< α <1)
[Typical setting] 0 (512 internally)
This parameter has the same function as damping compensation of the
tandem control function. When 512 is specified, the advance amount
is 0 degree. (See Subsec. 4.21.2.)
2738 (FS15i) Integral gain Ki

2325 (FS30i, 16i)
This parameter compensates for a machine spring element. Set a large
value when the rigidity is high. Set a small value for a motor with a
greater torque constant.
2738 (FS15i) Phase compensation coefficient 2T/t

2325 (FS30i, 16i)
(Set this parameter for the slave axis only.)
This parameter is used with coefficient α to compensate the
compensation delay. When the resonance frequency is 100 Hz or more,
set α = 100 and 2T/t = 6.
2746 (FS15i) Incomplete integral time constant

2333 (FS30i, 16i)
As integral gain Ki increases, vibration in the low frequency area (10
Hz or less) may occur. In such a case, set the incomplete integral time
constant to decrease the time constant. Set a parameter value listed
below.
Table 4.19.1 Setting in the incomplete integral time constant parameter

(when HRV1, HRV2, HRV3 is used)
Time constant (sec) Parameter setting
0.1 30887
0.05 29307
0.02 25810
- 420 -
(5) Adjustment method

• Check the torque commands for the master axis and slave axis
and velocity feedback vibration by using a check board. (See
Item (6).)
• If the vibration phase is shifted by 180 degrees, the cause of
resonance is assumed to be inter-axis interference.
• Enable tandem disturbance elimination control, and adjust
integral gain Ki.
• Increase the value of integral gain Ki gradually from 0, and
observe vibration. Ki has an optimal value. When the value of Ki
is increased excessively, vibration becomes stronger.
• When the velocity loop gain is changed, the frequency of
vibration changes. So, adjust Ki to minimize vibration.
• If the frequency of vibration exceeds 100 Hz, the effect of
tandem disturbance elimination control decreases. In such a case,
set phase compensation coefficients α and 2T/t or increase the
current loop gain with the current 1/2 PI control function.
Effect of tandem disturbance elimination control
Main axis velocity

feedback resonance 50 Hz Interference is
improved.
Sub-axis
vibration
* Velocity feedback and vibration frequency when the slave axis is

vibrated
- 421 -
(6) Method of checking the frequency of vibration

In this adjustment, use the disturbance input function for the slave axis,
measure the velocity feedback for the master axis, check for
interference between the axes, and check and adjust the effect of
tandem disturbance elimination control.
The following explains how to use the disturbance input function and
how to make settings for data measurement.
(a) Setting parameters related to disturbance input

Parameters related to the disturbance input function are set for the
slave axis.
(About the disturbance input function)

The disturbance input function applies vibration to an axis by
inputting a sine wave disturbance to the torque command. In the
adjustment of tandem disturbance elimination control, this function is
used for the slave axis to observe the interference status between the
axes when vibration is applied to the slave axis.
For the slave axis, set parameters related to the disturbance input
function.
#7 #6 #5 #4 #3 #2 #1 #0
2683 (FS15i) DSTIN DSTTAN DSTWAV
2270 (FS30i, 16i)
DSTIN(#7) Disturbance input
0: Stop
1: Start (Disturbance input starts on the rising edge from 0 to 1.)
DSTTAN(#6) Set 0.
DSTWAV(#5) Set 0.
2739 (FS15i) Disturbance input gain

2326 (FS30i, 16i)
[Setting value] 500
(*) Set the amplitude of the applied vibration (torque). (Value 7282
is equivalent to the maximum current of the amplifier.)
First, set about 500 to apply vibration to the machine so that light
sound is generated. If it is difficult to observe the vibration status,
increase the parameter value gradually.
2740 (FS15i) Disturbance input function: Start frequency (Hz)

2327 (FS30i, 16i)
[Setting value] 0
(*) If 0 is set, the default (10 Hz) is assumed to be the vibration start
frequency.
- 422 -
2741 (FS15i) Disturbance input end frequency

2328 (FS30i, 16i)
[Setting value] 0
(*) If 0 is set, the default (200 Hz) is assumed to be the vibration end
frequency.
2742 (FS15i) Number of disturbance input measurement points
2329 (FS30i, 16i)

[Setting value] 0
(*) If 0 is set, the default (3) is assumed as the number of disturbance
input measurement points.
[Cautions]
1 Disable the functions that operate only in the stop state, such as
the variable proportional gain function in the stop state and the
overshoot compensation function.
2 When characteristics at the time of cutting are measured,
cutting/rapid switching functions should be treated carefully.
3 Decrease the position gain to about 1000.
(b) Channel setting with SERVO GUIDE

With SERVO GUIDE, make settings for data acquisition. Two types
of data including disturbance frequency data (the master axis) and
velocity feedback data (the slave axis) are acquired at the same time.
From the graph window menu of SERVO GUIDE, select [Setting]

then [Channel].
Channel 1: Disturbance frequency

• Specify the slave axis as the axis, and set the data type to
"FREQ". (The other items are automatically set when FREQ is
selected.)
Channel 2: Master axis velocity feedback

• Specify the master axis as the axis, and set the data type to
"SPEED".
• Set the conversion coefficient to 1, and set the conversion base
data to 1.
- 423 -
• Check the check box of the extended address, and set an address
as listed in the table below. (The setting varies depending on the
value set in parameter No. 1023.) Set the shift amount to 0.
No.1023 Odd Even
Series 90D0 596 724
Series 90B0, Series 90B1, Series 90B5, Series 90B6 340 468
Series 90B3, Series 90B7 2048 2176
No.1023 (n:0,1,2,..) 4n+1 4n+2 4n+3 4n+4

Series 90E0 596 724 6740 6868
(c) Setting for sampling

Set the sampling cycle to 250 µs.
- 424 -
(d) Usage
When the rising edge of the disturbance input bit (DSTIN) is detected,
application of vibration is started. Vibration is automatically stopped
after a sine sweep is performed from the start frequency to the end
frequency. The operation is stopped by a reset or an emergency stop.
After the emergency stop is released, disturbance input is resumed
starting with the start frequency by setting the function bit off then on
again.
[Example of setting]
No.2326 = 500 Æ Gain = 500
No.2327 = 0 Æ Start frequency = 10Hz
No.2328 = 0 Æ End frequency = 200Hz
No.2329 = 0 Æ Number of measurement points = 3
By using SERVO GUIDE, obtain data, and display the frequency
(ch1) and velocity feedback (ch2) in the XY-YT mode.
Gain
characteristic
Input sine wave

frequency
Resonance point
Velocity feedback
Frequency
As shown in the above waveform, the envelope of the velocity

feedback indicates the gain characteristic at each frequency, and a
swell portion in the waveform shows a resonance point.
Adjust the tandem disturbance elimination control parameters so that
the degree of the gain swell at the resonance point is reduced.
(7) Notes on Series 90B3 and 90B7

Series 90B3 and 90B7 are used for applications that require learning
control. It is assumed that the mechanical coupling between two
rotation axes, C1 and C2, is released. So, only when the two axes are
mechanically coupled with each other, tandem disturbance elimination
control functions. Whether the two axes are mechanically coupled
with each other can be checked using the input of the external signal
G139 (coupling flag). For details of the external signal interface, refer
to the description of "Tandem leaning control" in "Learning Function
Operator's Manual (A-63639E-034)".
- 425 -
4.20 SYNCHRONOUS AXES AUTOMATIC COMPENSATION
(1) Overview
With synchronized axes having a long stroke, a machine twist may
occur due to the absolute precision of the scale and thermal expansion
of the machine. In such a case, the master motor and slave motor of
the synchronized axes pull each other, and if a large current flows for
the pull, an overheat problem or OVC alarm is raised.
The fundamental cause of this is a measurement position error. Pitch
error compensation can compensate for the scale error but cannot
compensate for thermal expansion due to change in temperature.
The synchronous axes automatic compensation function is useful for
such cases. The function monitors a torque error between the master
and slave and corrects the position on the slave side slowly to reduce
the torque error.
(Structure of the synchronous axes automatic compensation function)
Master axis
Separate
Velocity detector
control
Position error
Low-pass
filter
Slave axis
Limit
Separate
detector
Velocity
control
Position error

Series 90D0/N(14) and subsequent editions
Series 90E0/N(14) and subsequent editions
NOTE
Servo HRV4 control exercises one-axis control with
one CPU, so that this function cannot be used
together with servo HRV4 control.
- 426 -

• The following parameters are all set for the slave axis (the axis
for which an even number is set in parameter No. 1023) only.
#7 #6 #5 #4 #3 #2 #1 #0
2688 (FS15i) ASYN
2275 (FS30i, 16i)
ASYN (#3) Synchronous axes automatic compensation function is:
0: Disabled.
1: Enabled.
2816 (FS15i) Synchronous axes automatic compensation coefficient (K)

2403 (FS30i, 16i)
[Unit of data] Detection unit / TCMD unit × 4096
From the relationship between the current value generated in the
stopped state when this function is disabled and the position error
between the synchronized axes, determine the coefficient (K)
according to the following expression:
K = position error/current value (in TCMD) × 4096 ....................... <1>
When the current value is measured on the servo tuning screen, the
current value is indicated in amperes or as the percentage to the rated
current value. So, use expression <2> or <3> for calculation.
K = position error/{current value (%) × Ir × 7282/6554} × 4096
..................................................................................... <2>
Ir: Rated current in parameter No. 2086 (Series 16i) or No. 1979
(Series 15i)
K = position error/{current value (A)/Amax × 7282} × 4096
..................................................................................... <3>
Amax: Maximum current value of the amplifier
Measure the current value when the problem of a pull is being
observed at the release of emergency stop. The position error between
the synchronized axes is obtained from the difference in position error
between the master axis and slave axis at the time of emergency stop.
Normally, the position error of the master axis at the time of
emergency stop is 0, so you need to check the position error of the
slave axis only.
Example)
Suppose that the position error of the slave at the time of
emergency stop is 200, the current value at the release of
emergency stop is 60% (the percentage to the rating), and 1437 is
set in parameter No. 2086 (rated current value for the Series 16i):
Settings = 200 / { 1437 × 60/100 × 7282/6554 } × 4096 = 855
2817 (FS15i) Synchronous axes automatic compensation: Maximum compensation

2404 (FS30i, 16i)
Set the maximum compensation amount in synchronous axes
automatic compensation.
- 427 -
2818 (FS15i) Synchronous axes automatic compensation: Filter time constant

2405 (FS30i, 16i)
[Unit of data] sec
[Typical setting] 0 (1 second is applied.)
Set the time constant for reflecting the twist in position compensation.
As a larger time constant is set, compensation to release the twist is
performed more slowly.
NOTE
1 This function reduces the difference in torque
between the master and slave axes by adding
compensation pulses to the slave axis. In the
steady state, position error equivalent to the
compensation amount is accumulated in the slave
axis.
2 This function cannot be used together with the dual
position feedback function.
3 Set parameters on the even-numbered axis side.
4 When assigning servo axes to the synchronous
master and slave axes, ensure that an
odd-numbered axis is assigned to the master axis,
and an even-numbered axis ((master axis) + 1) is
assigned to the slave axis.
With the following servo software, a dead-band width can be set:

Set the following parameter for the odd-numbered axis side (the
master axis) only:
2817 (FS15i) Synchronous axes automatic compensation: Dead-band width

2404 (FS30i, 16i)
[Unit of data] Percentage (%) with respect to rated current
If the difference in torque command between the master axis and slave
axis is within the dead-band width, the synchronous axes automatic
compensation value becomes 0.
- 428 -
(4) Application example

The figure below shows how synchronous axes automatic
compensation works effectively.
When the master axis and slave axis, which are synchronized axes
connected mechanically, indicate different positions as position B, the
master axis and slave axis pull each other, and their TCMD
waveforms increase in the opposite directions.
Use of this function allows the position of the slave axis to move
slowly to such a position that is balanced with the master axis position,
so the problem that the axes pull each other does not occur.
Synchronous axes automatic Synchronous axes automatic compensation

compensation function: disabled function: enables
Master axis Master axis Master axis Master axis

Scale position A Scale position B Scale position A Scale position B
Slave axis Slave axis Slave axis Slave axis

Scale position A Scale position B Scale position A Scale position B
Actual Actual
federate federate
Master axis TCMD Master axis TCMD
Slave axis TCMD
Slave axis TCMD

Slave axis compensation
Position A Position B Position A Position A Position B Position A
- 429 -
4.21 TORQUE TANDEM CONTROL FUNCTION Optional function
(1) Overview
If a single motor is not capable of producing sufficient torque to drive
a large table, for example, tandem control allows two motors to
produce movement along one axis.
A motor of the same specification is used for both the main motor and
sub-motor.
Only the main motor is responsible for positioning. The sub-motor
only produces a torque. In this way, double the torque can be obtained
(load sharing mode).
By applying a preload torque to produce tension between the main

motor and sub-motor, the backlash between gears can be reduced
(anti-backlash mode).
Tandem control is used to run linked linear motors and motors with a
winding tandem (αiS300/2000, αiS500/2000, αiS1000/2000HV).
WARNING
When torque tandem control is used, position
control and velocity control are not exercised on
the sub-motor side. Use care.
When two motors are not connected with each
other, applying a force to the main motor side is
very dangerous, because the sub-motor may make
an extremely high-speed rotation.
(2) Applicable servo software series and editions

(Series 0i-C)
NOTE
Servo HRV4 control exercises one-axis control with
one CPU, so that this function cannot be used
together with servo HRV4 control.
- 430 -
Sub- Main
motor motor
Reducer Reducer
Pinion Pinion
Rack
Fig. 4.21 (a) Example of tandem control application (1)
Gear
Main
motor
Table
Ball screw
Sub-
motor
Fig. 4.21 (b) Example of tandem control application (2)
Servo amplifier Servo amplifier
FB cable
Slider Slider
Magnet
Fig. 4.21 (c) Example of exercising tandem control (linking linear motors)
Power Servo
supply amplifier
cable
αiS300
αiS500
αiS1000HV
Servo
amplifier
FB cable
Fig. 4.21 (d) Example of exercising tandem control (winding tandem)
- 431 -
(3) Start-up procedure

To start tandem control, follow the procedure below.
Start-up
procedure
Set tandem axis

(See <1> in Sec. 4.21(1))
Set direction of motor rotation

(See <2> in Sec. 4.21(2))
Set position feedback

(See <3> in Sec. 4.21(3))
Winding tandem?
Yes
No
Enable the motor feedback
Linear motor link? sharing function
Yes
(See Subsec. 4.21.5)
No
Set full-preload function

Full-preload?
Yes (See Subsec. 4.21.6)
No
To adjustment To usual
(See Subsec. 4.21.8) adjustment
Fig. 4.21 (e) Start-up procedure flowchart
<1> Tandem axis setting

Tandem control is an optional function.
Refer to the Parameter Manual of CNC for details.
#7 #6 #5 #4 #3 #2 #1 #0
1817 (FS15i) TANDEM
1817 (FS30i, 16i)
TANDEM (#6) 1: Enables tandem control. (Set this parameter for the main- and
sub-axes.)
- Number of CNC controlled axes (for Series 16i and so on)

1010 (FS16i)
As with the PMC axis, specify a number obtained by subtracting the
number of tandem sub-axes from the number of controlled axes.
If an invalid-parameter alarm is occurred, check whether the value set
in this parameter is correct.
- 432 -
1021 (FS15i) Parallel-axis name (for Series 15i only)

-
Specify 77 and 83 for the main axis and sub-axis, respectively.
1023 (FS15i) Servo axis arrangement

1023 (FS30i, 16i)
This parameter specifies servo axis arrangement.
Set an odd number for the main axis and set an even number ((main
axis) + 1) for the sub-axis.
If 3 is set for a main axis, for example, set 4 for the sub-axis.
NOTE
Specify a tandem sub-axis after a CNC-controlled
axis (command axis) (by referencing the following
examples of setting).
Example of tandem axis setting

(1) For Series 30i, 16i, and so on ( indicates a tandem axis.)
Number of controlled axes = 6
Number of CNC-controlled axes (No. 1010) = 3 (for Series 16i
and so on)
Servo axis Position
Axis Axis Tandem
arrangement display Remark
number name No. 1817#6
No. 1023 No. 3115#0
1 X 1 1 0 CNC axis (main axis)
2 Y 3 1 0 CNC axis (main axis)
3 Z 5 0 0 CNC axis
4 A 2 1 1 Tandem control sub-axis (sub-X-axis)
5 B 4 1 1 Tandem control sub-axis (sub-Y-axis)
6 C 6 0 0 PMC axis
(2) For Series 15i ( indicates a tandem axis.)

Servo axis Parallel
Axis Axis Tandem
arrangement axis Remark
number name No. 1817#6
No. 1023 No. 1021
1 XM 1 1 77 CNC axis (main axis)
2 YM 3 1 77 CNC axis (main axis)
3 Z 5 0 0 CNC axis
4 A 6 0 0 CNC axis
5 B 7 0 0 CNC axis
6 XS 2 1 83 Tandem control sub-axis (sub-X-axis)
7 YS 4 1 83 Tandem control sub-axis (sub-Y-axis)
- 433 -
<2> Direction of motor rotation

1879 (FS15i) Direction of motor rotation (DIRCT)
2022 (FS30i, 16i)
Main axis: With a forward direction specified, 111 specifies that the
main axis motor rotates counterclockwise as viewed from
the motor shaft side, while -111 specifies the opposite
direction.
Sub-axis: To cause the sub-axis motor to rotate in the same direction
as for the main axis, specify the same value for both the
sub-axis and the main axis because of their mechanical
structure. To cause the sub-axis motor to reverse, specify a
value whose sign is opposite to that for the normal
direction. For winding tandem, be sure to specify the
values with the same sign.
<3> Position feedback setting

Specify position feedback for both main axis and sub-axis. (See
Subsec. 4.21.8 for a concrete example.)
* Assume position feedback shown in Fig. 4.21.8 (a) not only for
the main axis but also for the sub-axis.
Series 30i,16i, Series 15i
and so on
• Semi-closed or full-closed loop setting No. 1815#1 No. 1815#1
No. 1807#3
• CMR setting No. 1820 No. 1820
• Setting the reference counter capacity No. 1821 No. 1896
• Setting the high-resolution Pulsecoder No. 2000#0 No. 1804#0
• Setting the number of velocity detection pulses
No. 2023 No. 1876
• Setting the number of position detection pulses
No. 2024 No. 1891
• Flexible feed gear (numerator) setting No. 2084 No. 1977
• Flexible feed gear (denominator) setting No. 2085 No. 1978
(4) Descriptions of servo parameters for adjustment

The load inertia ratio to be specified for axes subjected to tandem
control differs from that for ordinary axes.
1875 (FS15i) Load inertia ratio (LDINT)
2021 (FS30i, 16i)
[Standard setting] (Load inertia/motor inertia) × 256
(NOTE) In typical tandem control, the total load inertia of the machine is borne
by two motors. So, calculate the load inertia for the above formula as
follows:
(Load inertia) = (Total load inertia of machine)/2
Example of setting The example shown in Fig. 4.21 (a) is used. Assume that the inertia of
each section applied to the motor shaft as follows:
• Inertias of the reducers of the main- and sub-axes: J1m, J1s
• Inertias of the pinions of the main- and sub-axes: J2m, J2s
• Inertia of the rack: J3
(Total load inertia of the machine) = J1m + J2m + J3 + J1s + J2s
- 434 -
When the total load inertia of the machine is double that of the motor
inertia, for example, set the following:
When typical tandem control is used:
(Load inertia ratio) = (2/2) × 256 = 256
The result obtained from the above formula may cause oscillation due
to the mechanical structure. In such a case, set a smaller value.
• Notes on stable tandem control operation

To ensure stable tandem control operation, the machine must be
capable of performing back-feed.
Back-feed is the moving of the sub-motor from the main motor,
or vice versa, through the connected transmission feature. Then
the back-feed capability is disabled, unstable operation results. In
this case, machine adjustment becomes necessary.
The user can check whether the back-feed capability is enabled.
To make this check in the case of the example shown in Figs.
4.21 (a) and (b), turn the main motor with the power line for the
sub-motor disconnected, and check that the main motor can be
turned with one-third or less of the rated torque of the motor (See
(2) in Subsec. 4.21.8).
- 435 -
4.21.1 Preload Function

By applying an offset to the torque controlled by position (velocity)
feedback, torques of opposite directions can be applied to the main-
(main motor) and sub-axes (sub-motor) to maintain tension at all times.
This function can reduce the backlash between the main- and sub-axes,
caused by the tandem connection of two motors through gears.
However, this function does not reduce the backlash between the ball
screw and table, which are a feature of the machine system.
For example, set preload +Pre for the main axis and preload -Pre for
the sub-axis. Then, torques are produced as shown below.
If a torque is required during acc./dec., a torque of the same direction
is produced with the two motors. (Load sharing mode)
If no torque is required, for example, during stop state, preload torques
produce tension between the two axes. (Anti-backlash mode)
Sub-axis Main axis
−Pre +Pre
Stopped
Table
Sub-axis Drive torque Main axis Drive torque
−Pre +Pre
Accelerated
Direction of
movement
Sub-axis Drive torque Main axis Drive torque
−Pre +Pre
At constant
speed
When friction torque < preload torque Direction of
movement
When friction torque > preload torque Direction of

movement
Drive torque Sub-axis Drive torque Main axis
−Pre +Pre
Decelerated
Direction of
movement
Fig. 4.21.1 (a) Changes of torque during movement
- 436 -
Torque command
Torque limit
Main motor
+preload Required
torque
+preload
Required torque =
−preload (drive torque)/2
(Drive torque)/2 = (main + sub)/2
Sub-motor
− Torque limit
Fig. 4.21.1 (b) Relationship between required torque and torque
command for each motor
1980 (FS15i) Preload value (PRLOAD)

2087 (FS30i, 16i)
Set this parameter for the main- and sub-axes.
CAUTION
Set a value that is as small as possible but greater
than the static friction torque. A set preload torque
is applied to each motor at all times. So, set a
value that does not exceed the rated static torque
of each motor. As a guideline, specify a value
equal to one-third of the rated static torque.
As shown in Fig. 4.21.11 (a) in Subsec. 4.21.11, a
preload torque is added in any case. So, set the
preload torque directions as follows:
• When the rotation directions of the main axis
and sub-axis are the same: Different signs
• When the rotation directions of the main axis
and sub-axis are different: Same sign
- 437 -
Example of setting For the αiF4/4000 (Servo amplifier αi SV 40)

When a preload torque of 1 N⋅m is to be applied, the torque constant is
0.52 N⋅m/Arms according to the specifications of the servo motor.
So, the peak value is 0.368 N⋅m/Ap. The torque is converted to a
current value as follows:
1/0.368 = 2.72 Ap.
The amplifier limit is 40 Ap, so that the value to be set is:
2.72/40 × 7282 = 495
So, set 495 for the main axis, and -495 for the sub-axis (when the
directions of rotation of the two motors are the same).
When movement of the table is stopped, check whether the system is
in tension. If not, increase this value gradually.
WARNING
When two motors are not connected, always set a
preload value of 0.
The sub-axis motor may rotate at extremely high
speed, which is very dangerous. (→ See Subsec.
4.21.10, “Tandem Speed Difference Alarm
Function.”)
- 438 -
4.21.2 Damping Compensation Function

To enable more stable tandem control, a torque offset can be applied
to the sub-axis, or to both the main- and sub-axes to eliminate a
difference in speed, if any, between the main- and sub-axes.
This function is particularly useful for controlling the vibration (with a
frequency of several Hz to 30 or 40 Hz) that may occur in a machine
system with low spring rigidity.
Torque
command + Current
control
+
Detector Main
motor Backlash
Preload (main)
Spring
Velocity feedback
Damping compensation
+
+ +
Phase
Kc Table
compensation
−
Velocity feedback
Preload (sub) Sub-

Detector Backlash
motor
+ Spring
+ Current
control
Fig. 4.21.2 (a) Damping compensation function
#7 #6 #5 #4 #3 #2 #1 #0
1952 (FS15i) LAXDMP
2008 (FS30i, 16i)
LAXDMP (#7) 0: Enables the damping compensation function for the sub-axis
only.
1: Enables the damping compensation function for the main- and
sub-axes.
Usually, set this bit to 0. (Set this parameter for the main axis only.)
1721 (FS15i) Damping compensation gain Kc (ABPGL)

2036 (FS30i, 16i)
Set this parameter for the main axis only.
[Setting method] Kc × 32768 (0 ≤ Kc < 0.5)
A function bit is not supported for the damping compensation
function; the damping compensation function is enabled at all times.
When 0 is set in this parameter, the damping compensation function is
ineffective.
- 439 -
1721 (FS15i) Damping compensation phase coefficient α (ABPHL)

2036 (FS30i, 16i)
Set this parameter for the sub-axis only.
[Setting method] α × 512 (0.1 ≤ α ≤ 1.0)
When 0 is set in this parameter, this setting is internally handled as
512 (α = 1), When α = 1, phase compensation is not performed.
Instead, the set value is output to Kc as is.
(Example of adjustment) The speeds of the motors are checked using the Servo Guide (when
the motors rotate in the same direction).
This function may be useful when the oscillation frequencies (several
Hz to 30 or 40 Hz) are the same, and the phases are opposite as shown
below.
NOTE
1 When the directions of rotation of the main motor
and sub-motor are different, the phase relationship
is reversed.
2 When the phase difference is not 180°, the phase
coefficient α must be adjusted. Start with 512, then
decrease the value gradually.
Motor speed (main)
Motor speed (sub)
0 0.5 1 sec
Fig. 4.21.2 (b) Motor speed vibration
- Adjustment procedure for damping compensation

1 Enable the velocity feedback average function.
[No. 1952#2 (Series 15i), No. 2008#2 (Series 30i, 16i, and so on)
= 1]
2 Set an adequate preload value.
[No. 1980 (Series 15i), No. 2087 (Series 30i, 16i, and so on)]
Set a value slightly larger than the load applied during
movement.
- 440 -
3 If dual-position feedback function is used, set a time constant of

200 [No. 1973 (Series 15i), No. 2080 (Series 30i, 16i, and so
on)].
Adjust the setting of the parameter to ensure stable axis
movement.
4 Set 0 or 512 as phase coefficient α.
[Sub-axis No.1721 (Series 15i), No. 2036 (Series 30i, 16i, and so
on)]
If 512 is set, the value may have to be reduced when the
vibration phase difference between the motors is other than 180°.
(See Fig. 4.21.2 (b).)
5 Set a damping gain of 3277.
[Main axis No. 1721 (Series 15i), No. 2036 (Series 30i, 16i, and
so on)]
To reduce the vibration, this value must be increased or
decreased.
Be careful not to increase this value excessively. Otherwise,
high-frequency vibration will occur.
When adjusting this parameter, apply the maximum axis load.
6 Repeat steps 2 through 5 until smooth movement is achieved.
4.21.3 Velocity Feedback Average Function

As can be seen from the tandem control block diagram shown in Fig.
4.21.10(a) in Subsec. 4.21.10, velocity control is not applied to the
sub-axis motor. For this reason, the sub-axis may vibrate and become
unstable due to a backlash such as, for example, in the gears, in a
machine with a large backlash. In such a case, the machine can be
made stable by applying velocity control to the sub-axis as well.
This function is referred to as the velocity feedback average function.
#7 #6 #5 #4 #3 #2 #1 #0
1952 (FS15i) VFBAVE
2008 (FS30i, 16i)
VFBAVE (#2) 1: Enables the velocity feedback average function. Usually, set this
bit to 1. (Set this parameter for the main axis only.)
- 441 -
4.21.4 Servo Alarm 2-axis Simultaneous Monitor Function

If an alarm occurs in either of two axis motors used to operate a
machine in concert as in synchronization control or tandem control, it
is necessary to stop the other axis immediately so as to prevent the
machine from being twisted.
This function monitors two axes (controlled by the same DSP)
simultaneously for servo alarm conditions. If an alarm condition is
detected in either of the two axes, the function can promptly turn off
activation (MCC) for the other axis.
This function is not confined to tandem axes. It can be used also axes
(controlled by the same DSP) under synchronization control.
#7 #6 #5 #4 #3 #2 #1 #0
1951 (FS15i) IGNVRO ESP2AX
2007 (FS30i, 16i)
ESP2AX (#0) 1: Enables the servo alarm two-axis monitor function.
(Set this parameter for the main axis only.)
IGNVRO(#1) 1: An alarm condition is released 2 seconds after the servo alarm 2-axis
simultaneous monitor function holds the alarm condition.
(Series 9096, and Series 90B0/B(02) and earlier editions are not
supported.)
Some systems have a configuration in which the ESP line of the PSM
is cut off with an interlocked machine door, independently of the
emergency stop button, for safety purposes. In these systems, the
amplifier is turned off with an emergency stop not in effect, and
therefore, a "V ready-off alarm" is occurred. This alarm is evaded by
using the "VRDY OFF alarm invalidation signal."
Conventionally, however, it was impossible to use "PSM cut-off based

on the VRDY OFF alarm invalidation signal" along with the "servo
alarm 2-axis simultaneous monitor function." This is because the
"servo alarm 2-axis simultaneous monitor function" holds an alarm
condition in the servo software and will not activate a motor even after
the ESP line is connected.
To evade this problem, a function has been added which clears

information about an alarm condition from the servo software 2
seconds after the alarm condition is detected. This way, it is possible
to use the "servo alarm 2-axis simultaneous monitor function" along
with "PSM cut-off based on the VRDY OFF alarm invalidation
signal."
- 442 -
NOTE
It is necessary to release the VRDY OFF alarm
invalidation signal 2 seconds after the PSM ESP
signal is turned off.
ESP
Alarm
detected
2 seconds
VRDY OFF alarm
invalidation
To be tuned off 2 seconds after the ESP is turned off
- 443 -
4.21.5 Motor Feedback Sharing Function

To achieve improved thrust, two linear motors may be connected in
series.
When linear motors are connected in series, one position feedback
signal, which is originally available for the main axis, is to be shared
by the sub-axis as well. In this case, the motor feedback sharing
function can be used.
This function can also be used when a motor (αiS300/2000,
αiS500/2000, αiS1000/2000HV) with the wire tandem specification
is used.
NOTE
When using this function in a full-closed loop
system, the main axis shares its separate detector
feedback loop with the sub-axis.
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) PFBCPY
2018 (FS30i, 16i)
PFBCPY (#7) 1: The motor feedback signal for the main axis is shared with the
sub-axis motor.
(Set this parameter for the sub-axis only.)
NC
Feedback cable
Main axis feedback Linear motor Linear motor
Copy
Magnet
Sub-axis feedback
Fig. 4.21.5 Motor feedback sharing function
NOTE
If the scale of an axis for which this function is used
is based on the A/B phase, the sub-axis side
cannot perform absolute position communication.
Accordingly, note that this function cannot be used
with an absolute system.
- 444 -
4.21.6 Full-closed Feedback Sharing Function

If a feedback cable cannot be divided into two as in the case of a serial
cable, this function enables one separate position feedback to be
shared by the main axis and sub-axis by means of software.
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) FULLCP
2200 (FS30i, 16i)
FULLCP(#1) 1: A separate position feedback is shared by the main axis and the
sub-axis.
(To be set for the sub-axis only.)
NC
Main axis motor FB

Main
motor
Sub-axis motor FB
Separate FB cable
Main axis separate FB Scale
Copy
Sub
motor
Sub-axis separate FB
Fig. 4.21.7 (d) Full-closed feedback sharing function
NOTE
If the scale of an axis for which this function is used
is based on the A/B phase, the sub-axis side
cannot perform absolute position communication.
Accordingly, note that this function cannot be used
with an absolute system.
- 445 -
4.21.7 Adjustment
(1) Examples of parameter setting

This section gives examples of parameter setting.
<1> Full-closed loop system using a 1-µm increment system,
8080P/motor revolution for scale feedback, a scale detection unit
of 0.5 µm/P, and an αiA1000 Pulsecoder (conventional tandem)
CMR Main
Position command +
4 Position
control Motor
4040P/rev 2 8080P/rev
− αi Pulsecoder
1000000P/rev
F⋅FG
Motor position feedback
4
4
Reference
counter DMR
capacity
Machine position feedback
4 Machine
8080P/rev
4
CMR Sub
+
4 Position
control Motor
2 8080P/rev
− αi Pulsecoder
1000000P/rev
F⋅FG
Motor position feedback
101
12500
Reference
counter DMR
capacity
8080P/rev 4
4
Fig. 4.21.8 (a) Example of position feedback setting
Series 30i, 16i, and so on Series 15i Main Sub

• Tandem axis No. 1817#6 No. 1817#1 1 1
• Full-closed loop No. 1815#1 No. 1815#1 1 0
No. 1807#3 1 0
• CMR No. 1820 No. 1820 4 4
• Reference counter capacity No. 1821 No. 1896 8080 8080
• High-resolution Pulsecoder No. 2000#0 No. 1804#0 0 0
• Number of velocity detection pulses No. 2023 No. 1876 8192 8192
• Number of position detection pulses No. 2024 No. 1891 8080 12500
• Flexible feed gear No. 2084 No. 1977 0 101
- 446 -
<2> Semi-closed loop system using a 1/1000deg increment system,

rotary axis with a gear reduction ratio of 1/984, and an αiA1000
Pulsecoder (conventional tandem)

• Tandem axis No. 1817#6 No. 1817#1 1 1
• Semi-closed loop No. 1815#1 No. 1815#1 0 0
No. 1807#3 0 0
• CMR No. 1820 No. 1820 2 2
360000/984 36 3
(NOTE) = =
1000000 98400 8200
<3> Assuming a semi-closed loop system with an increment system

of 0.1 µm, 10 mm stroke per motor revolution, and αiS300
motor (winding tandem):

• Tandem axis No. 1817#6 No. 1817#1 1 1
• CMR No. 1820 No. 1820 2 2
• Motor feedback sharing function No. 2018#7 No. 1960#7 0 1
- 447 -
(2) Back-feed confirmation method

“Back-feed” means the feasibility that the axis can be driven not only
from motor side but also from machine table side.
(a) Check whether back-feed is possible when the machine is

connected and the power line is removed.
If back-feed is impossible, unstable control will result, and
machine adjustment such as a gear box adjustment will be
necessary.
<1> Making a check manually
First, turn the shaft of the main motor manually to check
that the sub-motor turns. Next, turn the shaft of the
sub-motor manually to check that the main motor turns. If
these checks are successful, back-feed is possible.
<2> Making a check using NC commands
After checking (b) and (c) below, remove the sub-motor
power line. Then, enter a plus (+) command or minus (-)
command to rotate the main motor. Check that the main
motor can be turned with one-third or less of its rated static
torque. When this check is successful, back-feed is possible.
(b) With the machine connected, activate the motors. At this time,
release the emergency stop state after reducing the torque limit
by a factor of about 10.
Check the motor current on the servo adjustment screen. If the
current increases gradually, the directions of rotation of the main-
and sub-motors may not be set correctly.
(c) Check the operation by entering a plus (+) command and minus
(-) command.
If the error persists due to friction load, increase the torque limit.
(d) If the operation is normal, return the torque limit to its original
value, and then set a preload value.
- 448 -
(3) Adjustment items

If vibration occurs:
• Check the position feedback setting (<3> in Sec. 4.21(3)).
• With SERVO GUIDE, check VCMD, TCMD, and POSF (VT
display). (With the check board, check the Vcmd, Tcmd, and
SPEED signals.)
(a) A higher gear reduction ratio tends to produce more backlash,

such that unstable operation will result from the sub-axis running
between backlashes.
→ Enable the velocity feedback average function.
(No. 1952#2 = 1) Series 15i
(No. 2008#2 = 1) Series 30i, 16i, and so on
(b) The main axis and sub-axis vibrate at the same frequency
(several Hz to 30 or 40 Hz) as a result of the spring rigidity being
low.
(The twist rigidity is proportional to the second power of the gear
reduction ratio, so that the frequency is probably a lower
resonant frequency.)
→ Enable damping compensation.
(See the adjustment procedure described in Subsec. 4.21.2.)
(No. 1952#2 = 1) Series 15i
(No. 2008#2 = 1) Series 30i, 16i, and so on
(c) The operation of a full-closed-loop system is unstable.

→ Check the position feedback setting (<3> in Sec. 4.21(3).)
If the parameters are set correctly, place the system in
semi-closed loop mode, then adjust the system to achieve
stable operation.
Then, return the system to full-closed loop mode. If the
operation is still unstable, apply a function such as the dual
position feedback function.
(d) In the stop state, no tension is established between the main axis
and sub-axis.
→ Set a preload value of 0, and check the torque in the stop
state.
Then, set a preload value greater than the stop-state torque.
(No. 1980) Series 15i
(No. 2087) Series 30i, 16i, and so on
(e) Position-dependent vibration occurs.

→ Change the feedrate to determine whether the vibration
frequency is constant or proportional to the feedrate.
If the vibration frequency is proportional to the feedrate,
position-dependent vibration is occurring. Check
position-related items such as the number of gear teeth.
- 449 -
4.21.8 Cautions for Controlling One Axis with Two Motors
(1) Tandem control and synchronous control (position tandem control)

selection criteria
Two control methods are supported to enable the control of one axis
using two motors: tandem control and synchronous control. The
(simple) synchronous control method controls the position of the
master axis and slave axis by using the same command. Position
control is exercised separately on each of the master axis and slave
axis. Control exercised when the master axis and slave axis are
allocated on the same CPU is particularly referred to as position
tandem control.
The tandem control method exercises position control over the main
axis only; this method exercises torque control over the sub-axis only.
(For clarity, the terms master and slave are used for synchronous
control, while main and sub are used for tandem control.)
When building an actual machine system, select a control method
suitable for the system, understanding the differences between the two
control methods.
In general, synchronous control, which controls the positions of two
axes, enables higher-precision control than torque tandem control.
Basically, use synchronous control in cases other than the following:
(Cases where torque tandem control is mainly used)
• When the output torques of two motors should be the same
• When the influence of backlash between two axes on a large
machine should be eliminated
• When an inter-axis interference occurs to make control unstable
if synchronous control is used
Main Sub-
motor motor
Reducer Reducer
Fig. 4.21.9 (a) Example of tandem control (machine system supporting back-feed)
Main
Main motor
motor
Sub-
Sub-
motor
motor
Fig. 4.21.9 (b) Example of synchronous control Fig. 4.21.9 (c) Example of tandem control
(to suppress the effect of a position difference) (when a torque two times greater is required)
- 450 -
4.21.9 Velocity loop integrator copy function

If the velocity loop integrator gets unbalanced between the master and
slave during synchronous or velocity command tandem control, the
axes may get twisted, leading to an OVC alarm.
This problem can be solved using a function that copies the velocity
loop integrator from the master axis to the slave axis, thereby
preventing integrator imbalance between the master and slave.
#7 #6 #5 #4 #3 #2 #1 #0
2686 (FS15i) WSVCP
2273 (FS30i, 16i)
WSVCP(#1) 1: The loop integrator of the master axis is copied to the slave axis.
(Specify only the slave axis.)
(Series 9096, and Series 90B0/M(13) and earlier editions are not
supported.)
CAUTION
1 When using this function, ensure that an
odd-numbered servo axis is assigned to the master
axis, and an even-numbered servo axis ((master
axis) + 1) is assigned to the slave axis.
2 No compatibility problem occurs between this
function and the system software.
3 This function bit is usable when simple
synchronous control or velocity command tandem
control is in use.
4 This function cannot be used together with the
preload function.
5 It is impossible to specify functions related to the
velocity loop integrator (such as the incomplete
integral or low-speed integral function) separately
for the master axis and slave axis.
6 This function cannot be used together with servo
HRV4 control.
- 451 -
4.21.10 Tandem Speed Difference Alarm Function
(1) Overview
Torque tandem control is a method of control for driving a rigidly
connected machine by using two motors. The speed of the sub-axis
side is not controlled. This means that if the mechanical connection is
canceled and a force is applied to the main axis side, the sub-axis can
rotate at an unnecessarily high speed. This function monitors the
speed difference between the main axis and sub-axis, and when the
parameter-set threshold is exceeded, "SV0641 SPEED DIFFERENCE
ALARM" is detected.

(Series 0i-C)
NOTE
The NC software of the following series and editions supports the message display
of alarm SV0641. Note that if NC software that does not support the message
display of alarm SV0641 is used, the message "SV0448 UNMATCHED
FEEDBACK ALARM" is displayed when this alarm is issued.
Series 30i-A Series G002, G012, G022 / 21.0 and subsequent editions
Series G003, G013, G023 / first edition and subsequent editions
Series 31i-A Series G101, G111 / 21.0 and subsequent editions
Series G103, G113 / first edition and subsequent editions
Series 31i-A5 Series G121, G131 / 21.0 and subsequent editions
Series G123, G133 / first edition and subsequent editions
Series 32i-A Series G201 / 21.0 and subsequent editions
Series G203 / first edition and subsequent editions
Series 16i-MB Series B0HA / 18 and subsequent editions
Series 16i-TB Series B1HA / 25 and subsequent editions
Series 18i-MB Series BDHA / 18 and subsequent editions
Series 18i-TB Series BEHA / 25 and subsequent editions
Series 18i-MB5 Series BDHE / 08 and subsequent editions
Series 21i-MB Series DDHA / 18 and subsequent editions
Series 21i-TB Series DEHA / 25 and subsequent editions
Series 0i-C Not applied to this function currently
Series 0iMate-C Not applied to this function currently
Power Mate i-D Series 88E1 / 06 and subsequent editions
Series 88E3 / 04 and subsequent editions
Power Mate i-H Series 88F2 / 13 and subsequent editions
Series 88F3 / 04 and subsequent editions
There is no plan for enabling the Series 15i-MB and Series 0i-B to support the
message display of alarm SV0641. (Alarm SV0448 is issued at all times.)
- 452 -

Set new parameters only with the slave axis of tandem control.
#7 #6 #5 #4 #3 #2 #1 #0
1951(FS15i) VLDALM
2007(FS30i,16i)
VLDALM (#4) The tandem speed difference alarm function is:
0: Used. (The tandem speed difference alarm function is enabled by
default.)
1: Not used.
2770(FS15i) Maximum permitted tandem speed difference

2357(FS30i,16i)
[Unit of data] min-1 (10 mm/min when a linear motor is used)
When 0 is set in this parameter, the threshold for the tandem speed
difference alarm function is set to 1000 by default.
When a negative value is set in this parameter, this function is
disabled.
- 453 -
4.21.11
Preload (main)
Torque
Velocity command command
+
Command
(1) Tandem control
Torque command
+
+
+
Position Velocity (main) Current Servo
− control control − control amplifier
+
-
Semi-closed loop
4.SERVO FUNCTION DETAILS
Velocity feedback
Block Diagrams
Main
0
motor
1
+
Full-closed loop
0
+
1/2 Damping
1
compensation
−
+
Scale
Velocity feedback averaging
- 454 -
Machine
Torque command
+
(sub)
+
Current Servo
control amplifier
+
Preload (sub)
Sub-
Velocity feedback motor
Fig. 4.21.11 Tandem control (typical)

B-65270EN/07
4.22 SERVO TUNING TOOL SERVO GUIDE
4.22.1 SERVO GUIDE
(1) Overview
The servo tuning tool SERVO GUIDE has the following features.
• PC-based integrated tuning tool for servo spindles
• Can be connected easily with a PCMCIA-LAN card from the
front of the CNC
• GUI-based ease of use
• Automatic tuning with the tuning navigator (Ver. 2.00 or later)
[Software ordering information]

A08B-9010-J900 (supplied on a CD-ROM)
[Upgrade ordering information]

A08B-9010-J901 (supplied on a CD-ROM)
To install software from an upgrade CD, SERVO GUIDE or i TUNE
of an older edition must have been installed on the personal computer
used.
- 455 -
(2) Operating environment

The following table lists operating environments for the servo tuning
tool SERVO GUIDE. The operating environment must be configured
with the listed hardware and software.
CNC (Note 1) Series 30i, 31i, 32i -MODEL A or later

Series 16i, 18i, 21i, 20i -MODEL Bor later
Series 0i -MODEL B, C
Series 0i Mate -MODEL B, C
Power Mate i -MODEL D, H
Pulse input type digital servo adapter
Personal computer PC/AT compatible
Ethernet port (for Ethernet connection)
FANUC HSSB board (for HSSB connection)
or
CNC display unit with PC functions (PANEL i)
OS Microsoft Windows 98/Me (Note 2)
Microsoft Windows NT4.0/2000/XP/Vista (Note 3)
Microsoft Windows 2000 or later is recommended. (Note 4)
Viewing online help requires Internet Explorer 4.01 or later. (Note 5)
CPU The recommended operating environment of the OS must be followed.
98/Me : Pentium 200MHz or later
NT4.0/2000 : Pentium 200MHz or later
XP : Pentium III 500MHz or later
Vista : Pentium III 1GHz or later
Memory The recommended operating environment of the OS must be followed.
98/Me : 64MB or more (Recommended 128MB or more)
NT4.0/2000 : 128MB or more (Recommended 256MB or more)
XP : 256MB or more (Recommended 512MB or more)
Vista : 512MB or more (Recommended 1GB or more)
Hard disk 35MB or more (Note 6)
(70MB during installation)
Display resolution SVGA (800 × 600) or higher
(XGA (1024 × 768) or higher is recommended.) (Note 7)
Printer Printer added by printer setting on Windows
PCMCIA LAN card Card specified by FANUC (A02B-0281-K710) (Note 8)
(for Ethernet connection)
Others Cross Ethernet cable and coupler (required for Ethernet connection)
(Note 9)
* Microsoft, Windows are registered trademarks of Microsoft

Corporation.
* This manual contains the program names or device names of
other companies, some of which are registered trademarks of
respective owners.
- 456 -
Note 1 The following software series and editions support SERVO

GUIDE.
[System software]
Series 30i-A G001/23 and subsequent editions,
G011/23 and subsequent editions,
G00A/01 and subsequent editions,
G022/01 and subsequent editions
(SERVO GUIDE Ver. 3.00 or later)
Series 31i-A G101/01 and subsequent editions,
Series 31i-A5 G121/01 and subsequent editions,
Series 32i-A G201/01 and subsequent editions
Series 16i-MB B0H1/05 and subsequent editions
B0HA/01 and subsequent editions
B0HK/01 and subsequent editions
B0K1/01 and subsequent editions
Series 16i-TB B1H1/06 and subsequent editions (*)
B1HA/01 and subsequent editions (*)
B1HK/01 and subsequent editions (*)
B1K1/01 and subsequent editions (*)
Series 18i-MB BDH1/05 and subsequent editions
BDHA/01 and subsequent editions
BDHK/01 and subsequent editions
BDK1/01 and subsequent editions
Series 18i-MB5 BDH5/01 and subsequent editions
BDHE/01 and subsequent editions
BDK5/01 and subsequent editions
Series 18i-TB BEH1/06 and subsequent editions (*)
BEHA/01 and subsequent editions (*)
BEHK/01 and subsequent editions (*)
BEK1/01 and subsequent editions (*)
Series 21i-MB DDH1/05 and subsequent editions
DDHA/01 and subsequent editions
DDHK/01 and subsequent editions
DDK1/01 and subsequent editions
- 457 -
Series 21i-TB DEH1/06 and subsequent editions (*)

DEHA/01 and subsequent editions (*)
DEHK/01 and subsequent editions (*)
DEK1/01 and subsequent editions (*)
Series 20i-FB D0H1/01 and subsequent editions
Series 20i-TB D1H1/01 and subsequent editions
Series 0i-MC D4B1/01 and subsequent editions
D4C1/01 and subsequent editions
Series 0i-TC D6B1/01 and subsequent editions
D6C1/01 and subsequent editions
Series 0i-TTC D6D1/01 and subsequent editions
Series 0i Mate-MC D511/01 and subsequent editions
D521/01 and subsequent editions
Series 0i Mate-TC D711/01 and subsequent editions
D721/01 and subsequent editions
Series 0i-MB D4A1/01 and subsequent editions
Series 0i-TB D6A1/01 and subsequent editions
Series 0i Mate-MB D501/01 and subsequent editions
Series 0i Mate-TB D701/01 and subsequent editions
Power Mate i-D 88E0/18 and subsequent editions
Power Mate i-H 88F2/01 and subsequent editions
Pulse input type digital servo adapter [A03B-0818-B121]
88F2/01 and subsequent editions
(*) For some of the T series CNCs, the system software of the
following editions is required to make a rigid tapping
synchronization error measurement:
Series 16i-TB B1H1/15 and subsequent editions
Series 18i-TB BEH1/15 and subsequent editions
Series 21i-TB DEH1/15 and subsequent editions
[Relationship between the Ethernet and open CNC]

For Series 30i, 31i, 32i
656E/06 and subsequent editions
656F/07 and subsequent editions
- 458 -
For Series 30i, 31i, 32i (when a 15” display is used)

Software for 15” display control
A02B-0207-J595#60VB 1.3 and subsequent editions
A02B-0207-J595#60VB 1.7 and subsequent editions
For Series 310is, 310is, 320is
WindowsCE.NET customized OS
A02B-0207-J594 1.2 and subsequent editions
WindowsCE.NET FOCAS2/HSSB library
A02B-0207-J808 1.5 and subsequent editions (SERVO
GUIDE Ver. 4.00 or later)
A02B-0207-J808 1.7 and subsequent editions (I/O
Link βi)
WindowsCE.NET standard application/library
For Series 16i, 18i, 21i
656A/03 and subsequent editions (Edition 656A/07
does not support the use of the PCMCIA LAN card.)
656A/04 and subsequent editions (when a sub-CPU is
provided)
656A/13 and subsequent editions (I/O Link βi)
For Series 0i-C, 20i-B
656V/01 and subsequent editions
For Series 0i-B
656A/05 and subsequent editions (Edition 656A/07
does not support the use of the PCMCIA LAN card.)
For Power Mate i
6567/01 and subsequent editions
6567/17 and subsequent editions (I/O Link βi)
For pulse input type digital servo adapter
[A03B-0818-B121]
6567/19 and subsequent editions
[Servo software]
For Series 30i,31i,32i
90D0/03(C) and subsequent editions,
90E0/03(C) and subsequent editions
For Series 16i,18i,21i,20i,0i,Power Mate i
90B0/06(F) and subsequent editions
(Note that using the tuning navigator requires
90B0/20(T) and subsequent editions.)
90B6/01(A) and subsequent editions,
90B8/01(A) and subsequent editions
For Series 21i, 0i, Power Mate i
9096/01(A) and subsequent editions
(They do not support the tuning navigator.)
- 459 -
[Spindle software]
For Series 30i,31i,32i
9D70/02 and subsequent editions
(For αi series spindle)
For Series 16i,18i,21i,0i,Power Mate i
(For αi series spindle)
For Series 16i,18i,21i,0i,Power Mate i
(For α series spindle)
(For some α series spindles, restrictions are placed on
data acquisition.)
[Related to I/O Link βi]

Control software for I/O Link βi
88A6/03(C) and subsequent editions
Power Mate CNC manager (J674)
Option
For Series 16i,18i,21i,Power Mate i
Power Mate CNC manager function (for βi)
8A01/03(C) and subsequent editions
SERVO GUIDE may operate on combinations other than stated

above. For αi series models, however, SERVO GUIDE can run
only on the combinations stated above.
In SERVO GUIDE version 3.00 and later versions, the parameter
window and program window also support the multipath CNC.
Note 2 It has yet to be verified whether SERVO GUIDE operates on

Windows 95.
Note 3 To use this software on Windows NT 4.0, install Service Pack
3 or later. Service Pack is available from Microsoft.
Note 4 On Windows 98/Me, opening multiple parameter and graph
windows at a time may result in insufficient resources. We
recommend Windows 2000 or later be used.
Note 5 Online help cannot be displayed unless Internet Explorer 4.01
or later is available.
Note 6 In addition to the program area, a storage area is necessary to
hold measured data.
Note 7 SERVO GUIDE can operate also on SVGA. If multiple
windows are open on SVGA, however, they overlap on one
another, impairing legibility.
Note 8 If you are using a Windows CE-based "is Series" CNC (160is,
180is, 210is), you do not need this card, because no LAN card
can be used to connect between the PC and CNC. (Use a
built-in Ethernet port for connection.)
With the is Series of the Series 30i (the 300is, 310is, and
320is), connection using a LAN card is also possible.
- 460 -
For use with the Power Mate i or pulse input type digital servo
adapter, connection using the PCMCIA-LAN card is disabled.
Get ready the following:
For the Power Mate i
- Fast Ethernet board (A02B-0259-J293)
- Fast Ethernet option (A02B-0259-J862)
- Ethernet software (A02B-0259-J555#6567)
- Extended basic 1 function option (A02B-0259-J878)
- Extended driver/library (A02B-0259-J847)
For the pulse input type digital servo adapter
- Fast Ethernet board (A02B-0259-J293)
- Fast Ethernet option (A03B-0818-J909)
- Ethernet software (A02B-0259-J555#6567)
Note 9 A FANUC-supplied LAN card is provided with a straight
cable with an RJ45 male connector attached. The following
figure shows how the cable is used to connect directly
between the PC and CNC.
Coupler
Cross cable Straight cable
(The cross cable and coupler are available from general PC

stores.)
The following figure shows how a hub is used to connect

between the PC and CNC. No coupler is needed. However,
you need to prepare a straight cable.
hub
Straight cable Straight cable
If you are using an HSSB, you may probably use an optical

cable to connect between the CNC and PC as shown below.
Using SERVO GUIDE does not require any additional
connection.
* Even if you are using a CNC display unit with PC functions,
such as the 160i, no additional connection is needed.
Optical cable
- 461 -
(3) Software specification overview

The servo tuning tool SERVO GUIDE has four windows ("parameter
window," "graph window," "program window," and "tuning
navigator"). The software specification overview of each window
follows.
(a) Parameter window

• Reads parameters from the NC, categorizes them by function,
and displays them.
• Supports servo and spindle parameters.
• Supports the automatic acc./dec. function for high speed and high
precision.
• Lets you modify NC parameters on the PC.
* The multipath system is supported by Version 3.00 and later
versions.
• Supports reading of the parameters of a CNC that employs the
FANUC Remote Option System.
* Version 4.00 and later versions.
(Details of supported functions)
Extracting and displaying information related to servo
System setting
sections from CNC options.
Whether there is a separate detector, rotary/linear
Servo axis setting
motor, CMR, flexible feed gear, etc.
Time constants for acc./dec. before interpolation and
acc./dec. after interpolation, speed difference related to
automatic deceleration at corner, arc radius-based
feedrate clamp setting, and acceleration-based
Acceleration/deceleration deceleration setting (ordinary control, advanced preview
control, AI advanced preview control, AI contour control,
AI nano-contour control, high-precision contour control,
AI nano high-precision contour control, AI contour
control I/II)
Current control HRV, HRV2, HRV3, or HRV4 control
Velocity loop gain setting, setting related to filters for
Velocity control measures for vibration in machine sections, vibration
control, and dual position feedback
Position control Setting of position gain
Contour error Setting related to feed-forward, backlash acceleration,
suppression and fine acc./dec. (for Series 16i and so on)
Overshoot improvement Setting for overshoot correction
Setting of FAD + advanced preview feed-forward and
High-speed positioning
position gain line graph
Setting related to brake control and quick stop at
Stop
emergency stop
Unexpected disturbance Estimated disturbance value tuning and alarm detection
torque detection level
Setting of AMR conversion coefficient and smoothing
Linear motor
compensation
Extracting and displaying information related to spindles
Spindle system setting
from CNC options.
Spindle system Motor edge sensor setting, spindle edge sensor setting,
configuration and gear ratio setting (main and sub)
- 462 -
Velocity loop gain setting and filter setting for

Spindle ordinary velocity
anti-vibration (main and sub) or resonance elimination
control
filter
Basic setting, stop position setting, velocity control
setting, position control setting, resonance elimination
Orientation
filter, optimum orientation setting, and high-speed
orientation setting
Command setting, velocity control setting (main and
Rigid tapping sub), position control setting, and fine acc./dec. (for
Series 16i and so on)
Command setting, velocity control setting, position
Cs contour control control setting, fine acc./dec. (for Series 16i and so on),
and resonance elimination filter
Spindle synchronous Velocity control setting, position control setting, and
control resonance elimination filter
Function categories
- Acceleration/deceleration
- Velocity control
- Rigid tapping, etc.
Tip on parameters
Acceleration/deceleration
pattern display
Parameter setting
Parameter window (example)

(b) Graph window
• Data measurement and display
- Horizontal axis time mode
Ordinary mode, first-order differential mode, second-order
differential mode (YT mode)
Feed smoothness measurement mode (DXDY mode)
Tangential velocity display mode (XTVT mode)
Synchronization error measurement mode (Synchro mode)
- XY mode (Polar coordinate interpolation and coordinate
conversion under angular axis control are possible.)
- Arc path error expansion mode (Circle mode)
- Arbitrary figure path error expansion mode (Contour mode)
- Frequency spectrum analysis mode (Fourier mode)
- Velocity loop frequency characteristic measurement mode
(Bode mode)
Data can be measured on both servo and spindle sections (even if
mixed)
- 463 -
* For non-αi series spindles, restrictions are placed on

measured data.
Simultaneous measurement is possible on up to eight channels
(with Version 4.10 or later, or up to six channels with earlier
versions).
* Up to four channels for two servo axes
* Up to two channels per spindle
When I/O Link βi axes are measured, up to two channels can be
measured simultaneously.
* Only one I/O Link βi axis can be measured at a time.
* Different I/O Link βi axes cannot be measured
simultaneously.
* An I/O Link βi axis and another CNC axis cannot be
measured simultaneously.
Display data can be printed output.
* Bit map data can be read via the clip board.
The highest-speed sampling period equals the current control
period or 62.5 us, whichever longer (servo axis only).
Example of measuring contour errors under Cs

contour axis control
Example of measuring velocity loop frequency

characteristics
Graph window (example)
- 464 -
• Linear motor smoothing compensation parameter

determination function
(Can be used with SERVO GUIDE Ver. 2.00 or later)
This function can easily determine the parameter for the
smoothing compensation function used to improve the feed
smoothness of a linear motor/synchronous built-in servo motor.
(Screen example)
Magnetic
pole position
(Tuning example)
Before tuning of smoothing compensation After tuning of smoothing compensation
Torque command
- 465 -
• Cursor function
Area expansion mode selection
Cursor display panel

• Display of waveform information
• Display of the vertical cursor
• Display of the horizontal cursor
Cursor Waveform information
By using the horizontal and vertical cursors, a waveform

measurement can be made.
The type of possible measurement depends on the display mode
as described below.
- YT mode : Inter-cursor differential measurement (time
measurement)
Measurements of a maximum value (Max),
minimum value (Min), average (Ave), and
root-mean-square (RMS) value in an
inter-cursor area
- XY mode : Inter-cursor differential measurement
- Fourier mode : Frequency, magnitude, phase
- Bode mode : Frequency, gain, phase
• Area expansion function

In the area expansion mode, a rectangular area can be selected by
dragging the left mouse button within the graph display area. By
left-clicking in the selected area, the selected area can be
enlarged.
Left-click in a selected rectangular area.
- 466 -
(c) Program window

• Test program creation assistance
- One-axis linear acc./dec.
- Arc
- Rectangle
- Rectangle with rounded corners
- Rigid tapping
- Cs contour
• Test program path display
• Sending test programs to NC memory and executing them
(The operator must press the start button.)
• Selecting and executing a program from NC memory
(The operator must press the start button.)
• Printing a created program
* The multipath system is supported by Version 3.00 and later
versions.
Program
Settings of
command
conditions
path
- Distance
- Radius
- Velocity, etc.
Character
strings in an
automatically
created
program
Program window (example)
- 467 -
(d) Tuning navigator

• Conditions for use
- Automatic tuning of velocity loop gain and filters

- High-speed and high-precision function setup support
- Automatic tuning of rapid traverse time constant
- Automatic quadrant protrusion compensation function
NOTE
Some functions cannot be used, depending on the
version of SERVO GUIDE and the series and
editions of CNC and servo software.
[Automatic tuning of velocity loop gain and filters] (Version 2.00

and later versions)
Measures the frequency characteristics of a velocity loop
while making the tool move along an axis to automatically
determine the values of the velocity loop gain and
resonance elimination filter parameters. Submitted
parameter values can be fine-tuned to verify their effects.
(This function is not supported by servo software Series
9096.)
Filter tuning (example)
- 468 -
[High-speed and high-precision function setup support] (Version

2.00 and later versions)
In a program for a square with corner rounding, the support
adjusts the parameters for high-speed and high-precision
functions while confirming overshoots. High-speed and
high-precision functions have multiple tuning parameters.
FANUC-recommended parameter sets (sets that give
priority to speed and those that give priority to precision)
are provided, and values between them can be selected
easily with a single operation on the slider.
High-speed and high-precision function tuning (example)
- 469 -
[Automatic tuning of rapid traverse time constant] (Version 4.00

and later versions)
By measuring the velocity and torque when a movement is
made on an axis by rapid traverse, this function
automatically determines a rapid traverse time constant.
With this function, a rapid traverse time constant can be
determined quickly.
Example of tuning
← 85%
Velocity
←15%
Torque command
Linear time constant 300 ms Linear time constant 32 ms

Bell-shaped time constant 96 ms Bell-shaped time constant 32 ms
- 470 -
[Automatic quadrant protrusion compensation function] (Version

4.00 and later versions)
By making several circular motions, this function
automatically determines the parameter for automatic
quadrant protrusion compensation. With this function,
quadrant protrusion tuning on an arc can be performed
quickly and easily.
This function is usable with the Series 30i, 31i, and 32i.
Example of tuning
<1> During learning Result of learning
<2> Recognition of optimum compensation Compensation value calculation
<3> <1> to <2> are executed at three different feedrates.
<4> Parameter presentation <5> Result check (Compensation

parameter application to the horizontal
axis)
- 471 -
(4) Tuning procedure overview

<1> Specify parameters from the parameter window.
<2> In the program window, create, send, and execute test programs.
<3> In the graph window, measure data.
<4> Repeat steps <1> to <3> to make optimum tunings while
watching the graphed data.
For details of usage, refer to "FANUC SERVO GUIDE Operator's

Manual (B-65404EN)" or the online manual after software
installation.
- 472 -
B-65270EN/07 5.DETAILS OF PARAMETERS
5 DETAILS OF PARAMETERS
Chapter 5, "DETAILS OF PARAMETERS", consists of the following
sections:
5.1 DETAILS OF THE SERVO PARAMETERS FOR Series 30i,

31i, 32i, 15i, 16i, 18i, 21i, 0i, 20i, Power Mate i (SERIES 90D0,
90E0, 90B0, 90B1, 90B6, 90B5, AND 9096)...........................474
- 473 -
5.DETAILS OF PARAMETERS B-65270EN/07
5.1 DETAILS OF THE SERVO PARAMETERS FOR Series 30i,

31i, 32i, 15i, 16i, 18i, 21i, 0i, 20i, Power Mate i (SERIES
90D0, 90E0, 90B0, 90B1, 90B6, 90B5, AND 9096)
The descriptions of parameters follow.

For parameters for which a specification method is not described, do
not change the parameters from the values set up automatically during
servo parameter initialization.
The parameter in the top left cell applies to Series 15i; the one in the
bottom left cell, to Series 30i, 31i, 32i, 16i, 18i, 20i, 21i, 0i, 20i,
Power Mate i.
: Do not change.
#7 #6 #5 #4 #3 #2 #1 #0
1815 (FS15i) APCX OPTX
1815 (FS30i, 16i)
OPTX (#1) A separate detector is:
0: Used.
1: Not used.
[Reference item] Subsection 2.1.3
APCX (#5) An absolute detector is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1817 (FS15i) TANDEM
1817 (FS30i, 16i)
TANDEM (#6) Tandem control (optional function) is:
0: Disabled.
1: Enabled.
Specify this parameter for both main axis and sub-axis.
[Reference item] Section 4.21
#7 #6 #5 #4 #3 #2 #1 #0
1804 (FS15i) PGEX PRMC DGPR PLC0
2000 (FS30i, 16i)
PLC0 (#0) Specifies whether to multiply the number of velocity and position
pulses by ten internally as follows:
0: Not to multiply by ten.
1: To multiply by ten.
DGPR (#1) When power is switched on, the motor-specific standard servo
parameter is:
0: Specified.
1: Not specified.
- 474 -
PRMC (#3) Do not change. ( )
PGEX (#4) The position gain range is:

0: Not expanded .
1: Expanded by 8 times.
#7 #6 #5 #4 #3 #2 #1 #0
2001 (FS30i, 16i)
AMR0 to AMR7 (#0 to #7) Specify the AMR value according to the Pulsecoder model for the
motor.
AMR
6 5 4 3 2 1 0
16-pole servo motors
0 0 0 1 0 0 0
αiS2000/2000HV, αiS3000/2000HV
Other than 16-pole servo motor
0 0 0 0 0 0 0
(8-pole servo motors)
[Related parameters] 2608#5 (15i), 2220#5 (16i etc.)
#7 #6 #5 #4 #3 #2 #1 #0
1807 (FS15i) PFSE
2002 (FS30i, 16i)
PFSE (#3) A separate detector is:
0: Not used.
1: Used.
Specify this parameter only in the Series 15i.
In the Series 30i, 31i, 32i, 16i, 18i, 21i, 0i, and Power Mate i, setting
bit 1 of parameter No. 1815 (OPT) to 1 automatically specifies this
parameter.
#7 #6 #5 #4 #3 #2 #1 #0
1808 (FS15i) VOFS OVSC BLEN NPSP PIEN OBEN TGAL
2003 (FS30i, 16i)
TGAL (#1) The software disconnection alarm detection level is:
0: Standard setting.
1: Lower sensitivity specified elsewhere.
[Related parameters] 1892 (15i), 2064 (16i etc.)
OBEN (#2) The velocity control observer function is:

0: Not used.
1: Used.
[Related parameters] 1859 (15i), 2047 (16i etc.), 1862 (15i), 2050 (16i etc.), 1863 (15i),
2051 (16i etc.)
- 475 -
PIEN (#3) The velocity control method to be used is:

0: I-P
1: PI
NPSP (#4) The N pulse suppression function is:

0: Not used.
1: Used.
BLEN (#5) The backlash acceleration function is:

0: Not used.
1: Used.
[Reference item] Subsections 4.6.6 and 4.6.7
OVSC (#6) The overshoot compensation function is:

0: Not used.
1: Used.
VOFS (#7) The VCMD offset function is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1809 (FS15i) TRW1 TRW0 TIB0 TIA0
2004 (FS30i, 16i)
TIA0 (#0), TIB0 (#1), TRW0 (#2), TRW1 (#3)
The setting of these bits varies according to the HRV control method.
TRW1 TRW0 TIB0 TIA0
0 1 1 0 For HRV1 control
0 0 1 1 For HRV2, HRV3, HRV4 control
#7 #6 #5 #4 #3 #2 #1 #0
1883 (FS15i) SFCM BRKC FEED
2005 (FS30i, 16i)
FEED (#1) The feed-forward function is:
0: Not used.
1: Used.
[Reference item] Subsections 4.6.1 to 4.6.5
[Related parameters] 1961 (15i), 2068 (16i etc.), 1985 (15i), 2092 (16i etc.)
BRKC (#6) The brake control function is:

0: Not used.
1: Used.
[Reference item] Section 4.10.
- 476 -
SFCM (#7) The static friction compensation function is:

0: Not used.
1: Used.
2073 (16i etc.)
#7 #6 #5 #4 #3 #2 #1 #0
1884 (FS15i) ACCF PKVE FCBL
2006 (FS30i, 16i)
FCBL (#0) During full-closed feedback, backlash compensation is:
0: Applied to the position.
1: Not applied to the position.
PKVE (#2) Speed-dependent current loop gain variable function is:

0: Not used
1: Used
( Do not change)
ACCF (#4) Specifies the amount of velocity feedback data to be used as follows:
0: Velocity feedback for the latest 2 ms.
1: Velocity feedback for the latest 1 ms.
#7 #6 #5 #4 #3 #2 #1 #0
1951 (FS15i) FRCAXS FAD IGNVRO ESP2AX
2007 (FS30i, 16i)
ESP2AX (#0) The servo alarm 2-axis simultaneous monitor function is:
0: Not used.
1: Used.
IGNVRO (#1) An alarm condition is:

0: Not released 2 seconds after the servo alarm 2-axes simultaneous
monitor holds the alarm condition.
1: Released 2 seconds after the servo alarm 2-axes simultaneous
monitor holds the alarm condition.
FAD (#6) The fine acc./dec. function is:

0: Not used.
1: Used.
FRCAXS (#7) Torque control function is:

0: Not used.
1: Used.
- 477 -
#7 #6 #5 #4 #3 #2 #1 #0
1952 (FS15i) LAXDMP PFBSWC VCMDTM SPPCHG SPPRLD VFBAVE TNDM
2008 (FS30i, 16i)
TNDM (#1) This bit is automatically set to 1 when bit 6 (tandem axis) of parameter
No. 1817 is set to 1. (In the Series 15i, this bit is kept at 0.) This bit
cannot be set directly.
VFBAVE (#2) 1: Enables the velocity feedback average function. (Usually, set this
bit to 1. Set this parameter for the main axis only.)
[Reference item] Section 4.19 and Subsection 4.21.3
SPPRLD (#3) 1: Enables the full preload function. (Set this parameter for the main
axis only.)
SPPCHG (#4) The motor output torque polarities are as follows:

0: Outputs only the positive polarity to the main axis, and outputs
only the negative polarity to the sub-axis.
1: Outputs only the negative polarity to the main axis, and outputs
only the positive polarity to the sub-axis. (Set this parameter for
the main axis only.)
VCMDTM (#5) 1: Enables velocity command tandem control.

PFBSWC (#6) 1: Switches position feedback according to the direction of a torque

command. (Set this parameter for the main axis only.)
LAXDMP (#7) 0: Enables damping compensation for the sub-axis only.

1: Enables damping compensation with both the main axis and
sub-axis. Usually, set this bit to 1. (Set this parameter for the
main axis only.)
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) BLST BLCU ANALOG DMY
2009 (FS30i, 16i)
DMY (#0) The serial feedback dummy function is:
0: Not used.
1: Used.
ANALOG(#4) Analog servo interface function is:

0: Not used
1: Used
- 478 -
BLCU(#6) The function that validates the backlash acceleration function only at
cutting is:
0: Invalidated.
1: Validated.
BLST (#7) The backlash acceleration stop function is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1954 (FS15i) POLE HBBL HBPE BLTE LINEAR
2010 (FS30i, 16i)
LINEAR (#2) Linear motor control is:
0: Not exercised.
1: Exercised.
This bit is set automatically when the parameters of the linear motor
are initialized. Check that this bit is set before the linear motor is
driven.
[Reference item] Subsec. 4.14.1.
BLTE (#3) The function to multiply the backlash acceleration amount by 10 is:
0: Invalidated.
1: Validated.
HBPE (#4) When the dual position feedback function is used, a pitch error
compensation is added to the error counter of:
0: Full-closed loop. ← Standard setting
1: Semi-closed loop.
HBBL (#5) When the dual position feedback function is used, a backlash
compensation amount is added to the error counter of:
0: Semi-closed loop. ← Standard setting
1: Full-closed loop.
POLE (#7) The punch/laser switching function is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1955 (FS15i) TMPABS RCCL FFAL EGB
2011 (FS30i, 16i)
EGB (#0) The EGB function is:
0: Not used.
1: Used.
- 479 -
FFAL (#1) Feed-forward control always is:

1: Enabled in all modes.
RCCL (#5) The actual current torque limit variable function is:
0: Not used.
1: Used.
( Do not change)
TMPABS (#7) Temporary absolute coordination setting function is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1956 (FS15i) STNG VCM2 VCM1 MSFE
2012 (FS30i, 16i)
MSFE (#1) The machine speed feedback function is:
0: Not used.
1: Used.
VCM1 (#4) The VCMD waveform signal conversion on the check board is
switched.
VCM2 (#5) Switches the VCMD waveform conversion value according to the
following list:
For rotary type motor
VCM2 VCM1 Number of velocity commandrevolution/5 V
0 0 0.9155 min-1
0 1 14 min-1
1 0 234 min-1
1 1 3750 min-1
For linear motor (P in the table below represents a scale signal pitch.)
VCM2 VCM1 Number of velocity commandrevolution/5 V
0 0 0.00375 × P m/min
0 1 0.06 × P m/min
1 0 0.96 × P m/min
1 1 15.36 × P m/min
[Reference item] Item (5) in Appendix I
STNG (#7) In velocity command mode, a software disconnection alarm is:

0: Detected.
1: Ignored.
- 480 -
#7 #6 #5 #4 #3 #2 #1 #0
1707 (FS15i) APTG HR3
2013 (FS30i, 16i)
HR3 (#0) HRV3 current control is:
0: Not used.
1: Used.
APTG (#7) The α Pulsecoder software disconnection monitor is:

0: Not ignored.
1: Ignored .
#7 #6 #5 #4 #3 #2 #1 #0
1708 (FS15i) HR4
2014 (FS30i, 16i)
HR4 (#0) HRV4 current control is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1957 (FS15i) BZNG BLAT TDOU SSG1 PGTW
2015 (FS30i, 16i)
PGTW (#0) The position gain switching function is:
0: Not used.
1: Used.
SSG1 (#1) The low-speed integral function is:

0: Not used.
1: Used.
TDOU (#5) Switches the check board output data as follows:

0: TCMD is output.
1: Estimated load torque is output.
[Reference item] Appendix I
BLAT (#6) The two-stage backlash acceleration function is:

0: Not used.
1: Used.
BZNG (#7) When a separate detector is used, the battery alarm for the built-in
Pulsecoder is:
0: Not ignored.
1: Ignored .
- 481 -
#7 #6 #5 #4 #3 #2 #1 #0
1958 (FS15i) PK2VDN ABNT
2016 (FS30i, 16i)
ABNT (#0) The unexpected disturbance torque detection function (option) is:
0: Not used.
1: Used.
PK2VDN (#3) The variable proportional gain function in the stop state is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1959 (FS15i) PK2V25 RISCFF HTNG COMSRC DBST
2017 (FS30i, 16i)
DBST (#0) The quick stop type 1 at emergency stop is:
0: Not used.
1: Used.
COMSRC(#3) The detector on the semi-closed side is:

0: Automatically identified.
1: αi/βi pulse coder at all times.
HTNG (#4) In velocity command mode, the hardware disconnection alarm of a

separate detector is:
0: Detected.
1: Ignored .
RISCFF (#5) 0: When RISC is used, the feed-forward response characteristics

remain as is.
1: When RISC is used, the feed-forward response characteristics are
improved.
PK2V25 (#7) Velocity loop high cycle management function is:

0: Not used.
1: Used.
- 482 -
#7 #6 #5 #4 #3 #2 #1 #0
1960 (FS15i) PFBCPY OVR8 MOVOBS RVRSE
2018 (FS30i, 16i)
RVRSE (#0) The signal direction for the separate detector is:
0: Not reversed.
1: Reversed.
Series 9096 does not support this parameter.
MOVOBS (#1) The disable function for observer in the stop state is:
0: Not used.
1: Used
OVR8 (#2) The stage-2 acceleration amount override format is on the basis of:
0: 4096 .
1: 256.
PFBCPY (#7) 1: The motor feedback signal for the main axis is shared by the
sub-axis. (Set this parameter for the sub-axis only.)
#7 #6 #5 #4 #3 #2 #1 #0
1709 (FS15i) DPFB TANDMP
2019 (FS30i, 16i)
TANDMP (#1) The tandem disturbance elimination control function (option) is:
0: Not used.
1: Used.
DPFB(#7) The dual position feedback function (option) is:

0: Not used.
1: Used.
2080 (16i etc.)
#7 #6 #5 #4 #3 #2 #1 #0
1740 (FS15i) P2EX RISCMC ABG0 IQOB OVSP
2200 (FS30i, 16i)
OVSP (#0) A feedback mismatch alarm is:
0: Detected.
1: Not detected.
IQOB (#2) 1: Eliminates the effect of voltage saturation on unexpected

disturbance torque detection.
- 483 -
ABG0(#3) 1: When an unexpected disturbance torque is detected, a threshold

is set separately for cutting and rapid traverse.
RISCMC (#5) When a RISC processor is used:

0: The response to a positioning command is the same as before.
1: The response to a positioning command is improved.
P2EX (#6) The velocity loop proportional gain (PK2V) format is:
0: Standard format. (See Item (5) of Subsec. 4.14.1.)
1: Converted format.
[Reference item] Supplement 4 of Subsection 2.1.5
#7 #6 #5 #4 #3 #2 #1 #0
1741 (FS15i) CPEE RNLV CROFS
2201 (FS30i, 16i)
CROFS (#0) The function for obtaining current offsets upon an emergency stop is:
0: Not used.
1: Used.
RNLV (#1) Specifies the detection level for the feedback mismatch alarm as
follows:
0: 600 min-1
1: 1000 min-1
CPEE (#6) The actual current display peak hold function is:
0: Not used
1: Used
#7 #6 #5 #4 #3 #2 #1 #0
1742 (FS15i) DUAL0W OVS1 PIAL VGCCR FADCH
2202 (FS30i, 16i)
FADCH (#0) The cutting/rapid FAD switching function is:
0: Not used.
1: Used.
2007 (16i etc.)
VGCCR (#1) The cutting/rapid velocity loop gain switching function is:
0: Not used.
1: Used.
- 484 -
PIAL (#2) When rapid traverse is selected by the cutting/rapid velocity loop gain
switching function, the 1/2 PI control function is:
0: Automatically disabled.
1: Always enabled.
OVS1 (#3) 1: Overshoot compensation is valid only once after the termination
of a move command.
DUAL0W (#4) For zero-width judgment:

0: Semi-full error only is used.
1: Both of a position error and semi-full error are used.
#7 #6 #5 #4 #3 #2 #1 #0
1743 (FS15i) TCMD4X FRCAX2 CRPI
2203 (FS30i, 16i)
CRPI (#2) The current loop 1/2 PI control function is:
0: Not used.
1: Used.
FRCAX2 (#4) Torque control type 2 is:

0: Not exercised .
1: Exercised.
TCMD4X (#5) The check board output voltage of the TCMD signal is:
0: As usual (default).
1: Multiplied by 4.
#7 #6 #5 #4 #3 #2 #1 #0
1744 (FS15i) DBS2 PGTWN2 HSTP10
2204 (FS30i, 16i)
HSTP10 (#1) The valid speed increment system for the high-speed positioning
function is:
0: 0.01mm-1 (rotary motor), 0.01mm/min (linear motor).
1: 0.1mm-1 (rotary motor), 0.1mm/min (linear motor).
PGTWN2 (#5) Position gain switching type 2 is:

0: Not used.
1: Used.
- 485 -
DBS2 (#7) Quick stop type 2 at emergency stop is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
1745 (FS15i) HDIS HD2O FULDMY
2205 (FS30i, 16i)
FULDMY (#2) The dummy separate detector function is:
0: Not used.
1: Used.
HD2O (#3) The quick stop function for hardware disconnection of separate
detector is:
0: Not applied to axes under synchronous control.
1: Applied to axes under synchronous control .
HDIS (#4) The quick stop function for hardware disconnection of separate
detector is:
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
1746 (FS15i) HSSR HBSF
2206 (FS30i, 16i)
HBSF (#4) The backlash compensation amount and pitch error compensation
amount are added:
0: Selectively according to the conventional parameter (No. 2010
(Series 16i etc.) and No. 1954 (Series 15i))If this parameter is set
to 1 (enabled), the settings of parameter No. 2010 (Series 16i
etc.) and parameter No. 1954 (Series 15i) are ignored.
1: Simultaneously for the full-closed and semi-closed sides.
HSSR (#7) High-speed data output to the check board is:

0: Not performed.
1: Performed.
- 486 -
#7 #6 #5 #4 #3 #2 #1 #0
1747 (FS15i) PK2D50 NEGSHC
2207 (FS30i, 16i)
NEGSHC (#0) Overcurrent alarm (software) is:
0: Not ignored.
1: Ignored .
[Related parameters] 1749#4 (15i), 2209#4 (16i etc.)
CAUTION
If the emergency stop state is released without
connecting the power line in a test such as a test
for machine start-up, the overcurrent alarm
detected by the servo software may be issued. In
such a case, the alarm can be avoided temporarily
by setting this bit parameter to 1. However, be sure
to return the bit parameter to 0 before starting up in
the normal operation state after completion of a
test.
PK2D50 (#3) Specifies a variable proportional gain function in the stop state as
follows:
0: 75% down.
1: 50% down.
#7 #6 #5 #4 #3 #2 #1 #0
1749 (FS15i) PGAT HCNGL FADPGC FADL
2209 (FS30i, 16i)
FADL (#2) 0: FAD bell-shaped type
1: FAD linear type
FADPGC (#3) 0: Synchronization is not established in the FAD setting rigid

tapping mode.
1: Synchronization is established in the FAD setting rigid tapping
mode.
- 487 -
HCNGL (#4) 0: The overcurrent alarm avoidance function based on amplifier

hardware is disabled.
1: The overcurrent alarm avoidance function based on amplifier
hardware is enabled.
NOTE
1 If an abnormal level of current that causes the
overcurrent alarm to be issued is detected
momentarily, processing is performed to suppress
the level of current without issuing the alarm.
2 Even if this function is used, the overcurrent alarm
is issued:
- When a complete short circuit occurs, or
- When the processing above for suppressing the
level of current is continuously performed.
PGAT (#6) 0: Automatic format change for position gain is enabled.1:

Automatic format change for position gain is disabled.
(available in Series 90B0/01 (A) and later editions)
#7 #6 #5 #4 #3 #2 #1 #0
1750 (FS15i) ESPTM1 ESPTM0 PK12S2
2210 (FS30i, 16i)
PK12S2 (#2) The current gain internally 4 times function is:
0: Not used.
1: Used.
ESPTM0(#5), ESPTM1(#6) Set the timer built into the αi amplifier to delay emergency stop.
0 0 50ms (default)
0 1 100ms
1 0 200ms
1 1 400ms
#7 #6 #5 #4 #3 #2 #1 #0
1751 (FS15i) PHCP
2211 (FS30i, 16i)
PHCP (#1) The phase lag compensation during deceleration is:
0: Not used.
1: Used.
- 488 -
#7 #6 #5 #4 #3 #2 #1 #0
2600 (FS15i) OVQK
2212 (FS30i, 16i)
OVQK (#7) When a quick stop function at the OVC and OVL alarm is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2601 (FS15i) OCM
2214 (FS30i, 16i)
OCM (#7) Pole position detection function (optional) is:
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
2602 (FS15i) FFCHG
2214 (FS30i, 16i)
FFCHG (#4) The cutting/rapid feed-forward switching function is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2603 (FS15i) ABT2 TCPCLR
2215 (FS30i, 16i)
TCPCLR (#1) A function of setting the velocity loop integrator with a value for
canceling a torque offset at an emergency stop is:
0: Disabled.
1: Enabled.
ABT2 (#7) Cutting/rapid unexpected disturbance torque detection function type 2

is:
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
2608 (FS15i) P16 DECAMR
2220 (FS30i, 16i)
DECAMR (#0) A non-binary detector is:
0: Not used.
1: Used.
- 489 -
P16 (#5) 16-pole servo motor is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2609 (FS15i) VFFNCH LNOTCH
2221 (FS30i, 16i)
LNOTCH (#1)
0: Uses resonance elimination filter 4.
1: Uses resonance elimination filter L.
VFFNCH (#2) Resonance elimination filter L is applied to:

0: Feed-forward part only of the velocity command
1: Entire velocity command
#7 #6 #5 #4 #3 #2 #1 #0
2611 (FS15i) BLCUT2 DISOBS
2223 (FS30i, 16i)
DISOBS (#0) The disturbance elimination filter function is:
0: Not used.
1: Used.
BLCUT2 (#7) The backlash acceleration function is:

0: Enabled for both cutting feed and rapid traverse
1: Enabled only for cutting feed
#7 #6 #5 #4 #3 #2 #1 #0
2613 (FS15i) TSA05 TCMD05
2225 (FS30i, 16i)
TCMD05 (#1) The check board output voltage of the TCMD signal is:
1: Halved.
TSA05 (#2) The check board output voltage of the SPEED signal is:
1: Halved (7500 min-1/5 V).
- 490 -
#7 #6 #5 #4 #3 #2 #1 #0
2616 (FS15i) ELSAL
2228 (FS30i, 16i)
ELSAL (#3) In pole detection, the motor saliency is:
0: Lq>Ld
1: Lq<Ld
#7 #6 #5 #4 #3 #2 #1 #0
2617 (FS15i) FORME WATRA ABSEN
2229 (FS30i, 16i)
ABSEN (#0) In pole detection, the AMR offset is:
0: Not used.
1: Used.
WATRA (#3) After pole detection, an abnormal operation is:

0: Monitored.
1: Not monitored.
NOTE
This function can be used with Series 90B1/B(02)
or later (FS15i, 16i, etc.) or Series 90D0 and
90E0/J(10) or later (FS30i, etc.).
FORME (#4) The operation mode for pole detection is:

0: Automatic selection mode (minute operation mode + stop mode)
NOTE
This function can be used with Series 90B1/B(02)
or later (FS15i, 16i, etc.) or Series 90D0 and
90E0/J(10) or later (FS30i, etc.).
#7 #6 #5 #4 #3 #2 #1 #0
2683 (FS15i) DSTIN DSTTAN DSTWAV AMR60
2270 (FS30i, 16i)
AMR60 (#0) The valid setting range of the AMR offset is from:
0: -45 degrees to +45 degrees.
1: -60 degrees to +60 degrees.
DSTWAV(#5) The input waveform of disturbance input is:

0: Sine wave. (Usually, select the sine wave.) .
1: Square wave.
[Reference item] Appendix H
- 491 -
DSTTAN(#6) Disturbance is:

0: Input for one axis only.
1: Input for both the L and M axes (To be set only for the L axis
side of synchronous axes or tandem axes).
DSTIN(#7) The disturbance input function is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2684 (FS15i) 2NDTMG RETR2
2271 (FS30i, 16i)
RETR2 (#2) When an unexpected disturbance torque is detected, the simultaneous
two-axis retract function is:
0: Not used.
1: Used.
2NDTMG (#5) Two-stage acceleration type 2 of two-stage backlash acceleration is:

0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2686 (FS15i) EGBFFG EGBEX POA1NG WSVCP
2273 (FS30i, 16i)
WSVCP (#0) When the simple synchronous control is used, the loop integrator of
the master axis :
0: Can not be copied to the slave axis.
1: Can be copied to the slave axis.
(Specify only the slave axis.)
POA1NG (#4) In the calculation of the observer coefficient (POA1), the load inertia
ratio (LDINT) is:
0: Considered.
1: Not considered.
EGBEX (#5) The EGB automatic phase matching function is:

0: In the normal mode (deceleration not performed between the
master and detector).
1: In the extended mode (deceleration performed between the
master and detector).
EGBFFG(#6) FFG is:

0: Not considered in the EGB ratio.
1: Considered in the EGB ratio.
- 492 -
#7 #6 #5 #4 #3 #2 #1 #0
2687 (FS15i) HP2048
2274 (FS30i, 16i)
HP2048 (#0) A 2048-time interpolation circuit (position detection circuit H or C) is:
0: Not used.
1: Used.
[Reference item] Subsection 2.1.4 and Section 4.14
#7 #6 #5 #4 #3 #2 #1 #0
2688 (FS15i) ASYN RCNCLR 800PLS
2275 (FS30i, 16i)
800PLS (#0) When the RCN723 or RCN223 is used, the reference counter setting is
made in reference to:
0: 1/8 turns of the detector.
1: 1 turn of the detector.
RCNCLR (#1) The speed data is:

0: Not cleared.
1: Cleared. (To use the RCN223 or RCN723, set it to 1.)
ASYN (#3) Synchronous axes automatic compensation function is:

0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
2690 (FS15i) ACC1ON ACC2ON ACC3ON ACCNEG
2277 (FS30i, 16i)
ACCNEG (#4) The sign of acceleration feedback is:
0: Not inverted.
1: Inverted.
ACC3ON (#4) Acceleration feedback in the third direction is:

0: Disabled.
1: Enabled.
ACC2ON (#4) Acceleration feedback in the second direction is:

0: Disabled.
1: Enabled.
ACC1ON (#4) Acceleration feedback in the first direction is:

0: Disabled.
1: Enabled.
- 493 -
#7 #6 #5 #4 #3 #2 #1 #0
2691 (FS15i) PM2ACC PM2SCB PM1SCB PM2TP PM1TP
2278 (FS30i, 16i)
PM1TP (#0) With the first or third separate detector interface unit, a temperature
0: Not used.
1: Used.
PM2TP (#1) With the second or fourth separate detector interface unit, a
0: Not used.
1: Used.
PM1SCB (#2) The first or third servo check interface unit is:
0: Not used.
1: Used.
[Reference item] Appendix J
PM2SCB (#3) The first or third servo check interface unit is:
0: Not used.
1: Used.
[Reference item] Appendix J
PM2ACC (#4) Acceleration sensor data is:

0: Read from the first or third separate detector interface unit
counted from the CNC, or no acceleration sensor is used.
1: Read from the second or fourth separate detector interface unit
counted from the CNC.
#7 #6 #5 #4 #3 #2 #1 #0
2692 (FS15i) DMCON
2279 (FS30i, 16i)
DMCON (#0) In emergency stop cancellation with the dummy function enabled:
0: The ready signal is not output.
1: The ready signal is output.
#7 #6 #5 #4 #3 #2 #1 #0
2695 (FS15i) FSAQS
2282 (FS30i, 16i)
FSAQS (#0) The quick stop function for separate serial detector alarms is:
0: Disabled.
1: Enabled.
- 494 -
#7 #6 #5 #4 #3 #2 #1 #0
2696 (FS15i) BLSTP2 NOG54
2283 (FS30i, 16i)
NOG54(#0) High-speed HRV current control mode (servo HRV3 control) is:
0: Used only when both G5.4Q1 and G01 are specified.
1: Used when G01 is specified. (G5.4Q1 is not monitored.)
NOTE
This function can be used when servo HRV3
control is used with the servo software for the
Series 30i/31i/32i (Series 90D0 and 90E0).
This function cannot be used when servo HRV4
control is used.
BLSTP2 (#7) The function for disabling backlash acceleration after a stop is:
0: Not used.
1: Used.
#7 #6 #5 #4 #3 #2 #1 #0
2701 (FS15i) MPCEF
2288 (FS30i, 16i)
MPCEF (#0) Machining point control is:
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
2703 (FS15i) ACCMON ACCHLD ACCOUT
2290 (FS30i, 16i)
ACCOUT(#0) To the diagnosis screen (No. 354), acceleration data output is:
0: Not performed.
1: Performed.
ACCHLD(#1) A peak acceleration rate is:

0: Not held.
1: Held (for 1 second).
ACCMON(#2) Machining point control outputs:

0: Acceleration data at all times
1: Remaining acceleration data after a stop (The acceleration data is
cleared to 0 during movement and for 16 ms after a stop.)
- 495 -
#7 #6 #5 #4 #3 #2 #1 #0
2705 (FS15i) MOVAXS MV1IFC MV1ID2 MV1ID1 MV1ID0 IFC1ON C1TYP1 C1TYP0
2292 (FS30i, 16i)
C1TYP0,1(#0,1) Sets a compensation type (for the first moving axis).
first moving axis.
0: Does not compensate for interactive force from the first moving
axis.
1: Compensates for interactive force from the first moving axis.
MV1ID0-2(#3,4,5) Specifies a servo axis number for the first moving axis.
MV1IFC(#6) Sets calculation of interactive force from the first moving axis.
0: Disables calculation of interactive force from the first moving
axis.
1: Enables calculation of interactive force from the first moving
axis.
MOVAXS(#7) Specifies whether the axis is a moving axis used with the interactive
force compensation function.
0: The axis is not a moving axis.
1: The axis is a moving axis.
#7 #6 #5 #4 #3 #2 #1 #0
2706 (FS15i) MV2IFC MV2ID2 MV2ID1 MV2ID0 IFC2ON C2TYP1 C2TYP0
2293 (FS30i, 16i)
C2TYP0,1(#0,1) Sets a compensation type (for the second moving axis).
second moving axis.
0: Does not compensate for interactive force from the second
moving axis.
1: Compensates for interactive force from the second moving axis.
MV2ID0-2(#3,4,5) Specifies a servo axis number for the second moving axis.
MV2IFC(#6) Sets calculation of interactive force from the second moving axis.
0: Disables calculation of interactive force from the second moving
axis.
1: Enables calculation of interactive force from the second moving
axis.
- 496 -
#7 #6 #5 #4 #3 #2 #1 #0
2713 (FS15i) CKLNOH THRMO DO HRVEN
2300 (FS30i, 16i)
HRVEN(#0) The extended HRV function is:
0: Not used.
1: Used.
NOTE
Set this function when using servo HRV4 control.
DD (#2) Synchronous built-in servo motor control is:

0: Disabled.
1: Enabled.
This bit is automatically set when the synchronous built-in servo
motor parameters are initialized. However, before driving a
synchronous built-in servo motor, check that this bit is set to 1.
THRMO (#3) When bit 7 of No. 2300 is set to 1, the overheat alarm of a motor is:
0: Obtained from a DI signal via the PMC.
1: Obtained from the αiCZ detection circuit, linear motor position
detection circuit, or temperature detection circuit.
CKLNOH (#7) The overheat alarm of a motor is:

0: Obtained from the pulse coder (for an αi/βi motor).
1: Obtained from a DI signal via the PMC, or from the αiCZ
detection circuit, linear motor position detection circuit, or
temperature detection circuit.
#7 #6 #5 #4 #3 #2 #1 #0
2714 (FS15i) TQCT10
2301 (FS30i, 16i)
TQCT10 (#7) The torque control setting range extension function is:
0: Disabled. (The setting of the torque constant parameter is used
without modification.)
1: Enabled. (The setting of the torque constant parameter is
increased by a factor of 10 for use in the NC.)
- 497 -
☆: Parameters set up automatically at initialization

★: Parameters that can be kept at the automatically set values
Parameter number
Series 30i, 16i, Details
Series 15i
and so on
1896 1821 Reference counter capacity →2.1.3
1825 1825 Position loop gain (position gain) →3.1.1
1851 1851 Backlash compensation value →4.6.6, 4.6.7
Motor ID No. → 2.1.2
1874 2020
Motor ID number that can be specified Initial setting
Load inertia ratio (LDINT)
Load inertia
× 256 Adjust for individual
1875 2021 Rotor inertia machines
separately.
Increase velocity loop gain parameters PK1V and PK2V by
(1 + LDINT/256) times
1879 2022 Rotation direction of the motor
→ 2.1.2
1876 2023 Number of velocity pulse
Initial setting
1891 2024 Number of position pulse
1713 2028 Velocity enabling position gain switching → 4.8.1
1714 2029 Acceleration-time velocity enabling integral function for low speed
→ 4.8.2
1715 2030 Deceleration-time velocity enabling integral function for low speed
1718 2033 Number of position feedback pulses

→ 4.5.7
1719 2034 Vibration damping control gain
Tandem control/damping compensation gain (main axis)
1721 2036 Tandem control/damping compensation phase coefficient → 4.21.2, 4.19
(sub-axis)
Two-stage backlash acceleration function : stage 2 acceleration
1724 2039 → 4.6.7
amount
1853 2041 Current loop gain (PK2) ★ Motor-specific
1855 2043 Velocity loop integral gain (PK1V) ☆ Motor-specific
Adjust for individual
1856 2044 Velocity loop proportional gain (PK2V) machines
separately.
☆ Motor-specific
1857 2045 Velocity loop incomplete integral gain (PK3V)
→ 4.7
1858 2046 Velocity loop gain (PK4V) ★ Motor-specific
Observer parameter (POA1)
This parameter is adjusted when the unexpected disturbance
☆ Motor-specific
1859 2047 torque detection and two-stage backlash functions are used.
→ 4.6.7, 4.12
NOTE: If the velocity gain (load inertia ratio) is changed, this
parameter must be re-adjusted.
1860 2048 Backlash acceleration amount ☆ → 4.6.6, 4.6.7
1861 2049 Maximum dual position feedback amplitude ☆ → 4.5.8
1862 2050 Observer gain (POK1)
1863 2051 Observer gain (POK2) ☆ Motor-specific
When only the unexpected disturbance torque detection function is → 4.12
used, these parameters must be changed.
1864 2052 Not used ★
- 498 -

Parameter number
Series 15i
and so on
1865 2053 Current dead-band compensation (PPMAX)
1866 2054 Current dead-band compensation (PDDP)
★ Motor-specific
The standard setting for αi motors is 1894.
1867 2055 Current dead-band compensation (PHYST)
1868 2056 Variable current loop gain during deceleration (EMFCMP)
1869 2057 Phase D current at high-speed (PVPA)
★ Motor-specific
1870 2058 Phase D current limit (PALPH)
1871 2059 Back electromotive force compensation (EMFBAS)
Torque limit
1872 2060 The standard setting represents the maximum current of the ★ Motor-specific
amplifier.
1873 2061 Back electromotive force compensation (EMFCMP)
1877 2062 Overload protection coefficient (POVC1) ★ Motor-specific
1878 2063 Overload protection coefficient (POVC2)
★ Motor-specific
1892 2064 Software disconnection alarm level
→ 3.2
1893 2065 Soft thermal coefficient (POVCLMT) ★ Motor-specific
1894 2066 Acceleration feedback gain ☆ → 4.4.2
1895 2067 Torque command filter ☆ → 4.5.2
1961 2068 Feed-forward coefficient
☆ → 4.6.1 to 4.6.5
1962 2069 Velocity feed-forward coefficient
1963 2070 Backlash acceleration timing ☆
Time during which backlash acceleration is effective,
1964 2071 ☆ → 4.6.6, 4.6.8
Static friction compensation count
1965 2072 Static friction compensation amount
☆ → 4.6.8
1966 2073 Stop state judgment parameter
1967 2074 Current loop gain variable with velocity ★ Motor-specific
1968 2075 Not in use at present. ☆
1969 2076 Not in use at present. ☆
1970 2077 Overshoot compensation counter ☆ → 4.7
1971 2078 Dual position feedback: Conversion coefficient (numerator)
1972 2079 Dual position feedback: Conversion coefficient (denominator)
☆ → 4.5.8
1973 2080 Dual position feedback: Constant of first-order lag
1974 2081 Dual position feedback: Zero zone
1975 2082 Backlash acceleration stop amount ☆ → 4.6.6, 4.6.7
1976 2083 Brake control timer (msec) ☆ → 4.10
1977 2084 Flexible feed gear (numerator) → 2.1.2
1978 2085 Flexible feed gear (denominator) Initial setting
1979 2086 Rated current parameter ★ Motor-specific
Torque offset ☆ → 4.6.7, 4.12
1980 2087
Tandem control/Preload value ☆ → 4.21.1
1981 2088 Machine speed feedback gain ☆ → 4.5.9
Two-stage backlash acceleration function : stage-2 end
1982 2089 ☆ → 4.6.7
magnification
1984 2091 Nonlinear control parameter ☆
1985 2092 Advanced preview feed-forward coefficient ☆ → 4.6.2
1987 2094 Backlash acceleration amount in the negative direction ☆ →4.6.6, 4.6.7
1988 2095 Feed-forward timing adjustment coefficient ☆ →4.6.5
- 499 -

Parameter number
Series 15i
and so on
1989 2096 Machining point control: Timing adjustment parameter (MPCTIM) →4.5.10
1990 2097 Static friction compensation stop parameter ☆ → 4.6.8
1991 2098 Current phase lead compensation coefficient ★ Motor-specific
1992 2099 N pulses suppression function ★ → 4.4.4
1994 2101 Overshoot compensation valid level ☆ → 4.7
1995 2102 Final clamp value for the actual-current limit ★ Motor-specific
Track back amount applied when an unexpected disturbance
1996 2103 ☆ → 4.12
torque is detected
Unexpected disturbance torque detection alarm level (cutting when
1997 2104 ☆ → 4.12
switching is used)
1998 2105 Torque constant ☆ → 4.18
1700 2107 Velocity loop gain magnification for cutting ☆ → 4.3
Fine acc./dec. time constant (rapid traverse when switching is
1702 2109 ☆ → 4.3 and 4.8.3
used)
1703 2110 Magnetic saturation compensation ★ Motor-specific
1704 2111 Torque limit at deceleration ★ Motor-specific
1705 2112 Linear motor AMR conversion coefficient 1 ☆ → 4.14
1706 2113 Resonance elimination filter 1: attenuation center frequency ☆ → 4.5.3
Backlash acceleration function : acceleration amount override → 4.6.6
1725 2114 Two-stage backlash acceleration function : stage 2 acceleration → 4.6.7
amount override
1726 2115 For internal data output: Usually to be kept at 0.
1727 2116 Unexpected disturbance torque detection : dynamic friction cancel → 4.12
Dual position feedback
1729 2118 → 4.5.8
Semi-closed/full-closed error overestimation level
1730 2119 Variable proportional gain function in the stop state : Stop level → 4.4.3, 4.5.6
1732 2121
Not used
1733 2122
1737 2126 Tandem control/position feedback switching time constant → 4.21.7
1735 2127 Non-interference control coefficient (NINTCT) ★ Motor-specific
1736 2128 Coefficient for magnetic flux weaken compensation (MFWKCE) ★ Motor-specific
1752 2129 Coefficient for magnetic flux weaken compensation (MFWKBL) ★ Motor-specific
1753 2130 Smoothing compensation performed twice per pole pair
1754 2131 Smoothing compensation performed four times per pole pair ☆ → 4.14.3
1755 2132 Smoothing compensation performed six times per pole pair
Coefficient for phase lag compensation during deceleration
1756 2133 ★ Motor-specific
(PHDLY1)
Coefficient for phase lag compensation during deceleration
1757 2134 ★ Motor-specific
(PHDLY2)
1760 2137 → 4.6.7
amount override
1761 2138 Linear motor AMR conversion coefficient 2
→ 4.14
1762 2139 Linear motor AMR offset
Unexpected disturbance torque detection alarm level in rapid
1765 2142 → 4.12.2
traverse
1766 2143 Fine acc./dec. time constant 2 (in cutting) → 4.3, 4.8.3
1767 2144 Position feed-forward coefficient for cutting
→ 4.3, 4.6.4, 4.8.3
1768 2145 Velocity feed-forward coefficient for cutting
- 500 -

Parameter number
Series 15i
and so on
1769 2146 Two-stage backlash acceleration end timer → 4.6.7
Deceleration decision level (HRV control) Usually adjustment
1771 2148
Usually to be kept at 0. is not needed.
1774 2151 For internal data output: Usually, be sure to set 0.
Static friction compensation function : decision level for movement
1777 2154 → 4.6.8
restart after stop.
1779 2156 Torque command filter (at rapid traverse) → 4.3, 4.5.2
1784 2161 OVC magnification at a stop (OVCSTP) ★ Motor-specific
1785 2162 Soft thermal coefficient 2 (POVC21)
1786 2163 Soft thermal coefficient 2 (POVC22) ★ Motor-specific
1787 2164 Soft thermal coefficient 2 (POVCLMT2)
1788 2165 Maximum amplifier current ★ Motor-specific
1790 2167 → 4.6.7
amount offset
Distance to lift for the lifting function against gravity at emergency
1796 2173 → 4.11.3
stop
2620 2177 Resonance elimination filter 1: attenuation bandwidth → 4.5.3
2622 2179 Reference counter size (denominator) → 2.1.3
2625 2182 Current A for pole detection (DTCCRT_A) → 4.15.1
→ 2.1, 2.1.8
2628 2185 Position pulses conversion coefficient
Initial setting
2641 2198 Current B for pole detection (DTCCRT_B)
→ 4.15.1
2642 2199 Current C for pole detection (DTCCRT_C)
2676 2263 Detection unit setting → 2.1.7
2678 2265 Machining point control: gain 2 (MPCK2)
→ 4.5.10
2679 2266 Machining point control: gain 1 (MPCK1)
Allowable travel distance magnification/stop speed decision value
2681 2268 → 4.15.1
(MFMPMD)
- 2315 Servo check interface unit output signal setting → Appendix J
2731 2318 Disturbance elimination filter : gain
2732 2319 Disturbance elimination filter : inertia ratio
2733 2320 Disturbance elimination filter : inverse function gain → 4.5.4
2734 2321 Disturbance elimination filter : time constant
2735 2322 Disturbance elimination filter : acceleration feedback limit
2736 2323 Variable current PI rate → 4.4.5
Variable proportional gain function in the stop state : arbitrary
2737 2324 → 4.4.3
magnification at a stop (for cutting only)
Tandem disturbance elimination control function/integral gain
(main axis)
2738 2325 → 4.19
Tandem disturbance elimination control function/phase coefficient
(sub-axis)
2739 2326 Disturbance input : gain
2740 2327 Disturbance input : start frequency
→ Appendix H
2741 2328 Disturbance input : end frequency
2742 2329 Number of disturbance input measurement points
- 501 -

Parameter number
Series 15i
and so on
Tandem disturbance elimination control function /incomplete
2746 2333 → 4.19
integral time constant (main axis)
2747 2334 In high-speed HRV current control mode: Current loop gain
magnification
→ 4.2
2748 2335 In high-speed HRV current control mode: Velocity loop gain
magnification
→4.6.6
Backlash acceleration function : acceleration amount limit value
2751 2338 Two-stage backlash acceleration function : stage-2 acceleration
→4.6.7
amount limit value
Two-stage backlash acceleration function : stage-2 acceleration

2752 2339 →4.6.7
amount (negative direction)
Backlash acceleration function : acceleration amount override →4.6.6
(negative direction)
2753 2340
Backlash acceleration function : Acceleration amount override →4.6.7
Two-stage backlash acceleration function : stage-2 acceleration →4.6.6
amount limit value (negative direction)
2754 2341
Two-stage backlash acceleration function : stage-2 acceleration →4.6.7
amount limit value (negative direction)
2755 2342 Unexpected disturbance torque detection: Acceleration threshold
2756 2343 Unexpected disturbance torque detection: Alarm level for high →4.12.3
acceleration
2758 2345 Disturbance estimation function : dynamic friction compensation
value in the stop state
→ 4.12.1
2759 2346 Disturbance estimation function : dynamic friction compensation
limit value
2768 2355 Machining point control: Center frequency of band-pass filter →4.5.10
- 2357 Tandem speed difference alarm threshold →4.21.10
2769 2356 Resonance elimination filter L: Feed-forward filter exclusion rate →4.5.5
2771 2358 Unexpected disturbance torque detection: Post-acceleration timer →4.12.3
2772 2359 Resonance elimination filter 1 : damping →4.5.3
2773 2360 Resonance elimination filter 2 : attenuation center frequency
2774 2361 Resonance elimination filter 2 : attenuation bandwidth →4.5.3
2775 2362 Resonance elimination filter 2 : damping
2777 2364 Resonance elimination filter 3 : attenuation bandwidth →4.5.3
2779 2366 Resonance elimination filter 4 / Resonance elimination filter L :
attenuation center frequency
→4.5.3, 4.5.5
attenuation bandwidth
damping
- 502 -

Parameter number
Series 15i
and so on
2782 2369 Smoothing compensation performed twice per pole pair (negative
direction)
2783 2370 Smoothing compensation performed four times per pole pair
→4.14.3
2785 2372 Serial EGB exponent setting
2786 2373 Lifting function against gravity at emergency stop : Distance to lift
→4.11.3
2787 2374 Lifting function against gravity at emergency stop : Lifting time
2790 2377 Smoothing compensation performed 1.5 times per pole pair
2791 2378 Smoothing compensation performed 1.5 times per pole pair →4.15.3
2793 2380 Smoothing compensation performed three times per pole pair
2794 2381 Smoothing compensation performed three times per pole pair →4.15.3
2795 2382 Torsion preview control: maximum compensation value (LSTCM) →4.6.9
2796 2383 Torsion preview control: acceleration 1 (LSTAC1)
2797 2384 Torsion preview control: acceleration 2 (LSTAC2) →4.6.9
2799 2386 Torsion preview control: acceleration torsion compensation value
K1 (LSTK1)
→4.6.9
K2 (LSTK2)
K3 (LSTK3)
2802 2389 Torsion preview control: torsion delay compensation value KD KD
(LSTKD)
→4.6.9
2803 2390 Torsion preview control: torsion delay compensation value KDN
(LSTKDN)
K1N (LSTK1N)
→4.6.9
K2N (LSTK2N)
K3N (LSTK3N)
2807 2394 Number of data mask digits →2.1.4
Feed-forward timing adjustment function (for use when FAD is
2808 2395 →4.6.5
enabled)
2815 2402 Torsion preview control: torsion torque compensation coefficient
→4.6.9
(LSTKT)
Synchronous axes automatic compensation function : coefficient
2816 2403 →4.20
(K)
Synchronous axes automatic compensation function : maximum
compensation (sub axis)
2817 2404 →4.20
Synchronous axes automatic compensation function : dead-band
width (main axis)
Synchronous axes automatic compensation function : filter
2818 2405 →4.20
coefficient
- 503 -

Parameter number
Series 15i
and so on
- 2455 Integer part of the number of pulses per revolution →4.17
- 2456 Exponent part of the number of pulses per revolution →4.17
- 2478 Interactive Force Compensation: Compensation gain (for the first
moving axis)
- 2479 Interactive Force Compensation: Angle data offset (for the first
moving axis)
→4.17
- 2480 Interactive Force Compensation: Compensation gain (for the
second moving axis)
- 2481 Interactive Force Compensation: Angle data offset (for the second
moving axis)
- 504 -
B-65270EN/07 6.PARAMETER LIST
6 PARAMETER LIST
Chapter 6, "PARAMETER LIST", consists of the following sections:
6.1 PARAMETERS FOR HRV1 CONTROL ................................506

6.2 PARAMETERS FOR HRV2 CONTROL ................................516
6.3 PARAMETERS FOR HRV1 CONTROL (FOR Series 0i-A) ..531
- 505 -
6.PARAMETER LIST B-65270EN/07
6.1 PARAMETERS FOR HRV1 CONTROL

August, 2007
Series 9096
Series 90B0
Series 90B1 and 90B8
- 506 -
L1500B1 L3000B2 L6000B2 L9000B2 L15000C2 αiS300 L3000B2 L6000B2 L9000B2 L15000C2 L300A1
Motor model
/4is /2is /2is /2is /2is 2000 /4is /4is /4is /3is /4is
Motor specification 444-B210 445-B110 447-B110 449-B110 456-B110 0292 445-B210 447-B210 449-B210 456-B210 441-B200
Motor ID No. 90 91 92 93 94 115 120 121 122 123 124
Symbol FS15i FS16i,etc
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 01000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000000 00000100 00000100 00000100 00000100 00000100
1955 2011 00000000 00000000 00000000 00000000 00000000 00100000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000100 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 10000000 10000000 10000000 10000000 10000000 00000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1890 4804 4804 5036 1420 1357 1620 2626 4944 2392 526
PK2 1853 2041 -7180 -14453 -13138 -16000 -5600 -4212 -11180 -10051 -11831 -8448 -2141
PK3 1854 2042 -2647 -2660 -2660 -2660 -2663 -2710 -2660 -2660 -2660 -2657 -2618
PK1V 1855 2043 19 16 16 14 10 114 16 10 16 10 16
PK2V 1856 2044 -260 -214 -214 -195 -131 -1023 -214 -135 -211 -128 -217
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -4371 -5321 -5321 -5849 -8681 3709 -5321 -8463 -5399 -8861 -8755
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 3787 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 -3850 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 -800 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 4855 7282 7282 5826
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32670 32670 32670 32685 32712 32352 32698 32740 32698 32732 32720
POVC2 1878 2063 1222 1222 1222 1041 703 5196 873 345 873 452 596
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 3626 3626 3626 3087 2086 15494 2590 1024 2590 1340 589
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 0 0 0 0 0 12288 0 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1402 1402 1402 1293 1063 2385 1184 744 1184 852 564
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 15000 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 227 455 911 1481 3104 10931 455 1450 1367 3168 52
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 16 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 1606 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 5500 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 791 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 1556 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 20494 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 45 45 85 135 245 365 85 245 245 365 25
- 507 -
L600A1 L900A1 L6000B2 L9000B2 L9000B2 L15000C2

Motor model
/4is /4is /4is /2is /4is /2is
Motor specification 442-B200 443-B200 (160A) (160A) (360A) (360A)
Motor ID No. 125 126 127 128 129 130
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000100
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000110 00001010 00001010
1708 2014 00000000 00000000 00000000 00000110 00001010 00001010
1750 2210 00000000 00000000 00000000 00000000 00000000 00000100
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 10000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 717 390 1751 6198 7416 2130
PK2 1853 2041 -3333 -2009 -6701 -19692 -17747 -8400
PK3 1854 2042 -2618 -2618 -2660 -2660 -2660 -2663
PK1V 1855 2043 9 13 15 12 10 7
PK2V 1856 2044 -122 -179 -202 -158 -141 -87
PK3V 1857 2045 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -9339 -6367 -5642 -7199 -8099 -13022
BLCMP 1860 2048 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0
TQLIM 1872 2060 6554 7282 7282 5917 4855 4855
EMFLMT 1873 2061 120 120 120 120 120 120
POVC1 1877 2062 32720 32721 32706 32713 32737 32743
POVC2 1878 2063 596 583 777 687 388 313
TGALMLV 1892 2064 4 4 4 4 4 4
POVCLMT 1893 2065 589 1326 2304 2038 1151 927
PK2VAUX 1894 2066 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0
AALPH 1967 2074 0 0 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0
RTCURR 1979 2086 564 847 1117 1050 789 708
TDPLD 1980 2087 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0
TRQCST 1998 2105 104 104 966 1823 2051 4656
LP24PA 1999 2106 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0
MAXCRT 1788 2165 45 45 165 165 365 365
- 508 -
βiS2 αiF1 βiS2 βiS2/4000 αiF2 βiS4 βiS4/4000 βiS8 βiS8/3000 αiS2 αiS2
Motor model 4000HV 5000 4000 SVSP40A 5000 4000 SVSP40A 3000 SVSP40A 5000 5000HV
Motor specification 0062 0202 0061 0061 0205 0063 0063 0075 0075 0212 0213
Motor ID No. 151 152 153 154 155 156 157 158 159 162 163
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00000000 00100000 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000100 00000000 00000100 00010000 00000000 00000000 00001110 00000000 00001110 00000000 00000000
1708 2014 00000100 00000000 00000100 00010000 00000000 00000000 00001110 00000000 00001110 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000010 00000010 00000010 00000010 00000010 00001110 00001110 00001110 00001110 00000010 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 225 672 280 560 680 288 576 450 900 600 420
PK2 1853 2041 -1100 -2294 -1080 -2160 -2247 -960 -1920 -1840 -3680 -1900 -1369
PK3 1854 2042 -2467 -2514 -1112 -1112 -2568 -1144 -1144 -1234 -1234 -2504 -2504
PK1V 1855 2043 78 66 78 39 76 112 56 164 82 39 39
PK2V 1856 2044 -700 -594 -698 -349 -680 -1008 -504 -1476 -738 -350 -351
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -1085 6384 -1089 -2178 5578 -753 -1506 5143 -1029 10853 -1081
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 -30 0 0 -30 -20 0 -30 0 -30 0
PVPA 1869 2057 -10250 0 -10250 -10245 -10256 -7700 -7690 -5144 -5133 -10250 -10254
PALPH 1870 2058 -1000 0 -1000 -500 -3300 -2240 -1120 -2700 -1350 -2000 -2300
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 6554 7282 6554 3277 7282 7282 3641 7282 3641 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32538 32613 32531 32531 32497 32289 32289 32289 32289 32528 32532
POVC2 1878 2063 2879 1933 2963 2963 3390 5988 5988 5994 5994 3005 2953
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 8560 5739 8811 2203 10085 17873 4468 17889 4472 8936 8782
PK2VAUX 1894 2066 -10 0 -10 -5 0 -10 -5 -10 -5 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 0 20480 0 4096 20480 0 16384 0 8192 16384
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1507 1234 1529 764 1636 2178 1089 2780 1390 1540 1526
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 10000 0 15000 7500 12000 0 0 0 0 0 7500
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 119 72 119 238 109 146 292 226 452 117 117
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1050 32 1050 564 32 782 284 1805 794 40 40
DETQLM 1704 2111 11600 7710 11600 11600 6460 7790 7790 7930 7930 7745 7700
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 2345 1188 1172 1172 1276 796 796 1442 1442 1137 1137
MFWKCE 1736 2128 1000 570 3000 6000 855 1000 2000 3500 7000 1000 1250
MFWKBL 1752 2129 2574 3211 2574 2574 3211 3130 3130 1552 1552 3851 3847
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 7188 2571 7188 7188 2565 7691 7691 3852 3852 2565 7688
PHDLY2 1757 2134 8990 12850 8990 8990 12850 8976 8976 8990 8990 12825 12850
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32767 32766 32766 32766 32765 32765 32762 32762 32766 32766
POVC22 1786 2163 19 13 20 20 23 42 42 74 74 20 20
POVCLMT2 1787 2164 3617 2425 3723 931 4261 7551 1888 12305 3076 3776 3711
MAXCRT 1788 2165 10 25 25 45 25 25 45 25 45 25 10
- 509 -
βiS4 αiS4 αiS4 βiS8 3000HV βiS12/2000 βiS12 βiS12 αC4 βiS12 αiF4 βiS22
Motor model 4000HV 5000 5000HV SVSP 40A 2000 3000HV 3000i 3000 4000 2000
Motor ID No. 164 165 166 167 168 169 170 171 172 173 174
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001110 00000010 00000010 00001110 00001110 00001110 00001110 00001000 00001110 00000010 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 309 400 280 580 951 320 361 926 400 659 750
PK2 1853 2041 -1092 -1154 -988 -2070 -3525 -1958 -1521 -4063 -1550 -2463 -3280
PK3 1854 2042 -2496 -2553 -2533 -2600 -1246 -1246 -2604 -2619 -1243 -2623 -1296
PK1V 1855 2043 112 64 64 166 115 230 170 115 170 106 242
PK2V 1856 2044 -1010 -574 -574 -1482 -1027 -2054 -1524 -1034 -1530 -953 -2172
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -751 6614 -661 5118 7390 3695 4978 3670 4960 3980 3496
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 -5140 0 0 0 0 0 0 -30 -20 0
PVPA 1869 2057 -7700 -10262 -8978 -5144 -3862 -3884 -5140 -5915 -5140 -11789 -3616
PALPH 1870 2058 -3000 -3500 -4000 -3500 -2200 -4400 -3200 -1500 -2700 -180 -2800
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 3641 7282 7282 7282 7282 8010 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32299 32289 32289 32301 32646 32284 32435 32406 32205 32446 32106
POVC2 1878 2063 5865 5994 5994 5842 1520 6045 4164 4529 7041 4029 8275
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 17504 17889 17889 17435 4511 18045 12399 13493 21044 11998 24770
PK2VAUX 1894 2066 -10 0 0 -10 -10 -10 -10 0 -10 0 -10
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 0 12288 12288 0 8192 20480 12288 16384 8192 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2155 2824 2824 2793 1563 3126 2356 1892 2363 1784 2618
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 8500 0 0 0 0 0 0 15000 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 146 127 127 225 630 315 420 190 418 201 692
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 777 24 32 1805 1282 1 1814 1289 1814 32 0
DETQLM 1704 2111 7790 10310 10290 7930 3940 3940 7930 3900 7930 5130 2866
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1592 646 500 2885 1350 1350 2388 2544 1194 1443 2459
MFWKCE 1736 2128 1000 2500 3000 1500 8000 4000 3000 5000 3000 2000 4500
MFWKBL 1752 2129 3339 3847 5122 1552 280 280 2056 1812 2056 3338 562
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 7686 2563 7692 3848 1812 1832 5133 3855 5133 6670 3089
PHDLY2 1757 2134 8976 12820 12850 8990 7700 8980 8978 8995 8978 8980 8982
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32765 32762 32762 32762 32766 32760 32764 32766 32764 32766 32763
POVC22 1786 2163 41 77 77 75 21 99 50 31 51 27 64
POVCLMT2 1787 2164 7395 12702 12702 12424 3890 15559 8836 5701 8891 5069 10913
MAXCRT 1788 2165 10 25 10 10 45 25 25 25 45 45 45
- 510 -
αiF4 αC8 αiF8 βiS22 αiF8 βiS0.5 βiS1 βiS8/3000 αiS8 αiS8 αiS12
Motor model 4000HV 2000i 3000 2000HV 3000HV 6000 6000 FS0i 4000 4000HV 4000
Motor specification 0225 0226 0227 0086 0229 0115 0116 0075-Bxx6 0235 0236 0238
Motor ID No. 175 176 177 178 179 181 182 183 185 186 188
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00000000 00000000 00000000 00100000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000010 00001010 00001010 00001110 00000000 00000010 00000010 00001110 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 525 1096 712 1025 886 141 398 450 544 694 657
PK2 1853 2041 -2056 -4638 -3187 -4010 -3174 -511 -1137 -1840 -2352 -2700 -2522
PK3 1854 2042 -2619 -2651 -2651 -2665 -2645 -2415 -2388 -1234 -2616 -2636 -2639
PK1V 1855 2043 113 150 113 244 113 7 6 164 33 34 52
PK2V 1856 2044 -1009 -1342 -1009 -2182 -1008 -59 -53 -1476 -294 -306 -466
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3762 2827 3760 3478 3764 -6462 -7176 5143 -1289 -1240 -815
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 -12850 -12850 -30 0 0 0
PVPA 1869 2057 0 -3854 -6418 -3616 -6159 0 -11530 -5144 -7691 -7690 -5904
PALPH 1870 2058 0 -1236 -3000 -2800 -1261 0 -1000 -2700 -2000 -2000 -2400
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 8010 7282 8010 6918 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32433 32289 32383 32433 32433 32674 32695 32381 32609 32596 32534
POVC2 1878 2063 4184 5994 4807 4185 4184 1178 915 4835 1993 2153 2923
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 12461 17889 14327 12462 12461 3497 2714 14410 5920 6396 8692
PK2VAUX 1894 2066 0 0 0 -10 0 0 0 -10 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 12288 8192 12288 12288 16384 20480 20480 16384 8192 8192 4096
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1888 2593 1950 2611 1948 1376 1212 2780 1253 1302 1518
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 0 0 0 15000 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 190 277 369 689 369 42 89 226 562 541 696
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1032 1552 786 0 782 30 30 1805 519 519 521
DETQLM 1704 2111 12388 3880 5180 2866 0 10290 10290 7930 7780 7268 5170
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 2573 2380 2103 5149 4191 1009 1763 1442 2106 5103 1592
MFWKCE 1736 2128 4000 4500 1500 2500 6000 0 0 3500 4000 4500 3000
MFWKBL 1752 2129 3348 1550 1815 562 1810 0 0 1552 2580 2580 2570
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 6670 3860 5140 3089 0 7690 11560 3852 5652 5150 5135
PHDLY2 1757 2134 8980 8990 8985 8982 0 12820 12880 8990 8990 8990 9000
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32763 32765 32763 32765 32767 32767 32764 32767 32767 32766
POVC22 1786 2163 31 63 33 64 33 16 12 51 13 14 19
POVCLMT2 1787 2164 5676 10709 6053 10854 6042 3015 2340 8896 2501 2702 3672
MAXCRT 1788 2165 25 25 45 25 25 25 25 25 85 45 85
- 511 -
αiS12 αC12 αiF12 βiS8/3000 αiF12 αC22 αiF22 βiS12/2000 αiF22 βiS12/2000 αC30
Motor model 4000HV 2000i 3000 FS0i 40A 3000HV 2000i 3000 FS0i 3000HV FS0i 40A 1500i
Motor specification 0239 0241 0243 0075-Bxx6 0245 0246 0247 0077-Bxx6 0249 0077-Bxx6 0251
Motor ID No. 189 191 193 194 195 196 197 198 199 200 201
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00100000 00000000 00100000 00000000 00100000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00001110 00000000
1708 2014 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00001110 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00000010 00000000 00001110 00000000 00001010 00000000 00001110 00000000 00001110 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 783 3809 1072 900 1044 1755 1458 320 1532 951 2644
PK2 1853 2041 -3006 -8197 -3835 -3680 -3677 -6536 -5416 -1958 -5641 -3525 -10345
PK3 1854 2042 -2666 -2679 -2630 -1234 -2679 -2694 -2690 -1246 -2692 -1246 -2695
PK1V 1855 2043 52 280 192 82 193 271 198 230 197 115 166
PK2V 1856 2044 -470 -2504 -1721 -738 -1727 -2426 -1775 -2054 -1765 -1027 -1486
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -808 1516 2204 -1029 2197 1565 2137 3695 2150 7390 2553
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -20 0 -5140 0 -20 0 -2590 0 0 0 0
PVPA 1869 2057 -5904 -1804 -8199 -5133 -8214 -2597 -5136 -3884 -4392 -3862 -1545
PALPH 1870 2058 -3000 -2500 -747 -1350 -2350 -1942 -2800 -4400 -2824 -2200 -1300
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 3641 7282 8010 7282 7282 7282 3641 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32530 32289 32520 32671 32548 32114 32520 32323 32548 32646 32520
POVC2 1878 2063 2976 5994 3101 1214 2755 8171 3101 5566 2755 1520 3101
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 8848 17889 9224 3603 8192 24454 9224 16603 8192 4511 9224
PK2VAUX 1894 2066 0 0 0 -5 0 0 0 -10 0 -10 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 8192 8192 0 12288 8192 8192 8192 8192 0 8192
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1532 3020 2085 1390 2092 2911 2131 3126 2118 1563 1655
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 15000 15000 0 15000 0 15000 0 15000 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 690 350 517 452 516 680 929 315 934 630 1630
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 521 0 32 794 774 1548 1291 1 787 1282 2059
DETQLM 1704 2111 6159 2168 0 7930 0 2600 0 3940 0 3940 2148
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 4904 4150 2388 1442 4787 3695 3272 1350 6547 1350 6680
MFWKCE 1736 2128 2000 12000 2000 7000 4000 4000 4500 4000 6000 8000 14000
MFWKBL 1752 2129 2575 1044 2568 1552 2320 1046 1301 280 1808 280 539
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 6174 5150 0 3852 0 2070 0 1832 0 1812 1054
PHDLY2 1757 2134 8990 8990 0 8990 0 9000 0 8980 0 7700 9000
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32761 32765 32767 32765 32761 32765 32763 32765 32767 32766
POVC22 1786 2163 20 91 38 12 39 83 40 60 40 15 23
POVCLMT2 1787 2164 3738 14518 6924 2224 6969 13493 7229 10250 7142 2785 4361
MAXCRT 1788 2165 45 25 85 45 45 45 85 25 45 45 85
- 512 -
Motor model βiS22/1500 αiF30 βiS22/1500 βiS2/4000 αiF40 αiF40 βiS2/4000 βiS4/4000 βiS4/4000 αiS22 αiS22
FS0i 3000 FS0i 40A FS0i 3000 3000Fan FS0i 40A FS0i FS0i 40A 4000 4000HV
Motor specification 0084-Bxx6 0253 0084-Bxx6 0061-Bxx6 0257 0257 0061-Bxx6 0063-Bxx6 0063-Bxx6 0265 0266
Motor ID No. 202 203 205 206 207 208 210 211 212 215 216
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00100000 00100000 00100000 00100000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00001110 00000100 00000000 00000000 00010000 00000000 00001110 00000000 00000000
1708 2014 00000000 00000000 00001110 00000100 00000000 00000000 00010000 00000000 00001110 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001110 00001010 00001110 00000010 00000010 00000010 00000010 00001110 00001110 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1048 597 4342 280 1289 1289 560 288 576 714 709
PK2 1853 2041 -4337 -2334 -11170 -1080 -5048 -5048 -2160 -960 -1920 -2904 -2806
PK3 1854 2042 -2659 -2694 -1329 -1112 -2696 -2696 -1112 -1144 -1144 -2674 -1345
PK1V 1855 2043 280 230 140 78 191 191 39 112 56 69 76
PK2V 1856 2044 -2507 -2057 -1254 -698 -1712 -1712 -349 -1008 -504 -616 -685
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3027 1845 6054 -1089 2216 2216 -2178 -753 -1506 6163 5538
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 -20 0 0 0
PVPA 1869 2057 -2110 -5170 -2079 -10250 -2570 -2570 -10245 -7700 -7690 -7689 -7684
PALPH 1870 2058 -4691 -1000 -2342 -1000 -2000 -2000 -500 -2240 -1120 -2000 -1000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 3641 6554 7282 7282 3277 7282 3641 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32319 32511 32655 32652 32511 32431 32739 32532 32709 32511 32501
POVC2 1878 2063 5617 3215 1411 1455 3215 4212 364 2945 738 3215 3332
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 16756 9565 4189 4317 9565 12545 1079 8758 2189 9565 9912
PK2VAUX 1894 2066 -10 0 -10 -10 0 0 -5 -10 -5 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 8192 0 20480 8192 8192 0 20480 0 4096 8192
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 3012 2306 1506 1529 1957 2593 764 2178 1089 1627 1810
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 15000 15000 15000 7500 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 597 1170 1194 119 1839 1839 238 146 292 1216 1093
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1025 1032 514 1050 1291 1291 564 782 284 519 513
DETQLM 1704 2111 2248 7735 2248 11600 5140 5140 11600 7790 7790 6224 6194
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 3290 1688 3290 1172 3041 3041 1172 796 796 2041 4264
MFWKCE 1736 2128 5500 2500 11000 3000 2000 2000 6000 1000 2000 2500 2000
MFWKBL 1752 2129 1032 2829 1032 2574 1553 1553 2574 3130 3130 2580 3092
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 2580 5140 2580 7188 3087 3087 7188 7691 7691 5150 5150
PHDLY2 1757 2134 8990 8995 4382 8990 8990 8990 8990 8976 8976 8990 8990
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 140 0 120 140 140 120 120 120 140 0
POVC21 1785 2162 32763 32764 32767 32757 32765 32718 32765 32745 32762 32766 32766
POVC22 1786 2163 60 48 14 140 33 629 34 294 70 23 28
POVCLMT2 1787 2164 10345 8466 2586 2665 6099 10707 666 5407 1352 4214 5218
MAXCRT 1788 2165 25 165 45 25 165 165 45 25 45 165 85
- 513 -
αiS30 αiS30 αiS40 αiS40 αiS50 αiS50 αiS50 αiS50 αiS100 αiS100 αiS200
Motor model 4000 4000HV 4000 4000HV 3000 3000Fan 3000HVFan 3000HV 2500Fan 2500HVFan 2500Fan
Motor ID No. 218 219 222 223 224 225 226 227 230 231 234
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 01000110 01000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00000000 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 689 816 748 860 528 528 680 680 874 980 1309
PK2 1853 2041 -2675 -3277 -3055 -3457 -2088 -2088 -2961 -2961 -4483 -4082 -5199
PK3 1854 2042 -2683 -2696 -2682 -2700 -2690 -2690 -2697 -2697 -2717 -2718 -2719
PK1V 1855 2043 82 82 92 93 69 69 70 70 91 91 115
PK2V 1856 2044 -733 -738 -827 -831 -622 -622 -628 -628 -819 -819 -1026
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 5175 5143 4589 4569 6099 6099 6039 6039 4632 4636 3699
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 31979 31979 31979 31979 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 3 3 3 3 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -6415 -6415 -5648 -5652 -5646 -5646 -5646 -5646 -4368 -3846 -3090
PALPH 1870 2058 -3000 -3000 -3000 -3600 -2000 -2000 -2000 -2000 -1359 -900 -2700
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32511 32501 32511 32501 32558 32348 32371 32554 32309 32309 32309
POVC2 1878 2063 3215 3332 3215 3332 2627 5245 4967 2680 5734 5734 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 9565 9912 9565 9912 7810 15639 14807 7968 27346 27346 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 4096 4096 4096 4096 4096 4096 0 0 20480 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1836 1847 2073 2083 1439 2037 2057 1454 2848 2848 3013
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 10000 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1470 1460 1701 1693 3312 3312 3279 3279 4589 4423 5973
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 775 775 776 769 519 519 519 519 776 1291 1290
DETQLM 1704 2111 6450 6430 5682 5682 6174 6174 6174 6174 3787 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1871 5117 1853 5230 2046 2046 4861 4861 3520 6952 3518
MFWKCE 1736 2128 4000 3000 4000 4000 6500 6500 2500 2500 6500 2000 4000
MFWKBL 1752 2129 2574 2574 2063 2063 2063 2063 2068 2068 1297 1549 1298
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 5150 5150 5150 5150 5150 5150 5140 5140 2570 0 2068
PHDLY2 1757 2134 8990 8990 8988 8988 8990 8990 9000 9000 8970 0 12820
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 140 0 140 0 0 0 0 0 140 140 140
POVC21 1785 2162 32766 32766 32765 32765 32754 32739 32738 32754 32745 32745 32745
POVC22 1786 2163 29 30 38 38 174 365 373 178 292 292 292
POVCLMT2 1787 2164 5369 5432 6846 6908 3300 6608 6736 3366 13952 13952 13952
MAXCRT 1788 2165 165 85 165 85 365 365 185 185 365 185 365
- 514 -
αiS100 αiS100 αiS200 αiS200 αiS200 αiS300 αiS500 αiS500 αiS1000

Motor model 2500 2500HV 2500HVFan 2500 2500HV 2000HV 2000 2000HV 2000HV
Motor specification 0285 0286 0289 0288 0289 0293 0295 0296 0298
Motor ID No. 235 236 237 238 239 243 245 246 248
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 01000110 00000110 01000110 01000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00000000 00001010 00001010 00001010 00001010 00001010 00001010 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 874 980 1194 1309 1194 1077 1943 1713 1053
PK2 1853 2041 -4483 -4082 -5535 -5199 -5535 -5101 -6970 -6505 -3316
PK3 1854 2042 -2717 -2718 -2719 -2719 -2719 -2712 -2711 -2713 -2722
PK1V 1855 2043 91 91 115 115 115 114 134 134 234
PK2V 1856 2044 -819 -819 -1026 -1026 -1026 -1025 -1199 -1199 -2096
PK3V 1857 2045 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 4632 4636 3699 3699 3699 3703 3164 3164 1811
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 3787 1894 3787 3787
PHYST 1867 2055 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -4368 -3846 -3088 -3090 -3088 -3846 -2068 -2070 -3097
PALPH 1870 2058 -1359 -900 -3000 -2700 -3000 -900 -2600 -2700 -2000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32310 32474 32309 32309 32309 32391 32309 32309 32309
POVC2 1878 2063 5728 3672 5734 5734 5734 4714 5734 5734 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 15662 15982 27346 27346 27346 23263 27346 27346 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 12288 12288 12288 12288 12288 12288 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1960 2033 3013 2712 2712 2483 2980 2980 2834
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 10000 0 0 0 0 0 0 15000
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 4589 4423 5973 5973 5973 10871 15096 15096 28573
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 776 1291 1291 1290 1291 1296 1296 1293 1296
DETQLM 1704 2111 3787 0 3428 0 3428 0 0 3714 3172
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 3520 6952 6729 3518 6729 7634 4175 8341 8637
MFWKCE 1736 2128 6500 2000 4000 4000 4000 5000 4000 4500 6000
MFWKBL 1752 2129 1297 1549 1551 1298 1551 1301 1041 788 1047
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 2570 0 2575 2068 2575 2574 2069 2324 2580
PHDLY2 1757 2134 8970 0 8984 12820 8984 12814 8981 8984 8985
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 106 140 140 140 140 140 140 140 140
POVC21 1785 2162 32750 32759 32745 32745 32745 32738 32745 32745 32745
POVC22 1786 2163 223 112 292 292 292 375 292 292 292
POVCLMT2 1787 2164 6581 6752 13952 13952 13952 13952 13952 13952 13952
MAXCRT 1788 2165 365 185 185 365 185 365 365 365 365
- 515 -
6.2 PARAMETERS FOR HRV2 CONTROL

August, 2007
Series 90B0
Series 90D0 and 90E0
- 516 -
βiS2 αiF1 βiS2 βiS2/4000 αiF2 βiS4 βiS4/4000 βiS8 βiS8/3000 βiS0.2 βiS0.3
Motor model 4000HV 5000 4000 SVSP40A 5000 4000 SVSP40A 3000 SVSP40A 5000 5000
Motor ID No. 251 252 253 254 255 256 257 258 259 260 261
Symbol FS15i FS16i,30i,etc
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000100 00000000 00000100 00010000 00000000 00000000 00001110 00000000 00001110 00000000 00000000
1708 2014 00000100 00000000 00000100 00010000 00000000 00000000 00001110 00000000 00001110 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001110 00001010 00001110 00001110 00001010 00001110 00001110 00001110 00001110 00000010 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 348 620 360 720 760 400 800 650 1160 123 210
PK2 1853 2041 -1676 -3034 -1920 -3840 -3743 -1920 -3840 -3831 -5600 -510 -970
PK3 1854 2042 -1232 -1256 -1237 -1237 -1283 -1253 -1253 -1299 -1299 -1069 -1146
PK1V 1855 2043 78 66 78 39 76 112 56 164 82 4 4
PK2V 1856 2044 -700 -594 -698 -349 -680 -1008 -504 -1476 -738 -36 -33
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -1085 6384 -1089 -2178 5578 -753 -1506 5143 -1029 -10638 -11550
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 -5130 0 0 -10 0 0 -2570 0 0 0
PVPA 1869 2057 -10250 0 -10250 -10245 -12298 -7694 -7687 -5140 -5131 0 0
PALPH 1870 2058 -1000 0 -1000 -500 -1275 -2800 -1400 -3200 -1600 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 6554 7282 6554 3277 7282 7282 3641 7282 3641 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32538 32613 32531 32531 32497 32289 32289 32289 32289 32725 32725
POVC2 1878 2063 2879 1933 2963 2963 3390 5988 5988 5994 5994 533 533
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 8560 5739 8811 2203 10085 17873 4468 17889 4472 3163 3163
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 20480 16384 0 12288 20480 0 16384 0 20480 20480
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1507 1234 1529 764 1636 2178 1089 2780 1390 1929 1929
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 119 72 119 238 109 146 292 226 452 7 14
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1048 32 1048 815 32 780 532 1807 1045 1 1
DETQLM 1704 2111 11600 10260 11600 11600 10280 7790 7790 7930 7930 7710 7700
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 2345 1188 1172 1172 1276 796 796 1442 1442 379 852
MFWKCE 1736 2128 1000 1667 2500 5000 2000 3000 6000 3500 7000 0 3000
MFWKBL 1752 2129 3358 3858 3358 3358 3862 3392 3392 1298 1298 0 3880
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 7192 7690 7192 7192 7693 8992 8992 3858 3858 7700 7695
PHDLY2 1757 2134 8990 12840 8990 8990 12840 12864 9024 8990 8990 12825 12840
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32767 32766 32766 32766 32765 32765 32762 32762 0 0
POVC22 1786 2163 19 13 20 20 23 42 42 74 74 0 0
POVCLMT2 1787 2164 3617 2425 3723 931 4261 7551 1888 12305 3076 0 0
MAXCRT 1788 2165 10 25 25 45 25 25 45 25 45 4 4
- 517 -
αiS2 αiS2 βiS4 αiS4 αiS4 βiS8 3000HV βiS12/2000 βiS12 βiS12 αC4 βiS12
Motor model 5000 5000HV 4000HV 5000 5000HV SVSP 40A 2000 3000HV 3000i 3000
Motor ID No. 262 263 264 265 266 267 268 269 270 271 272
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001110 00001010 00001010 00001110 00001110 00001110 00001110 00001010 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 530 400 331 420 425 605 1094 547 427 1240 402
PK2 1853 2041 -2543 -2312 -1560 -1748 -1641 -3028 -6578 -3289 -2301 -6415 -2217
PK3 1854 2042 -1251 -1251 -1246 -1276 -1266 -1300 -1305 -1305 -1302 -1309 -1304
PK1V 1855 2043 39 39 112 64 64 166 115 230 170 115 170
PK2V 1856 2044 -350 -351 -1010 -574 -574 -1482 -1027 -2054 -1524 -1034 -1530
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 10853 -1081 -751 -661 -661 5118 7390 3695 4978 3670 4960
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -10250 -10252 -7694 -8974 -10262 -5140 -3862 -3884 -5140 -5915 -5140
PALPH 1870 2058 -2000 -1600 -2800 -3641 -3300 -3200 -2175 -4350 -3500 -1500 -3500
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 3641 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32528 32532 32299 32289 32289 32301 32646 32284 32435 32406 32205
POVC2 1878 2063 3005 2953 5865 5994 5994 5842 1525 6045 4164 4529 7041
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 8936 8782 17504 17889 17889 17435 4511 18045 12399 13493 21044
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 16384 20480 12288 8192 20480 0 8192 20480 12288 16384
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1540 1526 2155 2824 2824 2793 1563 3126 2356 1892 2363
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 117 117 146 127 127 225 630 315 420 190 418
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 32 40 780 8 40 1807 1282 1 1814 1289 1814
DETQLM 1704 2111 8995 10260 7790 10295 10260 7930 3940 3940 7930 3900 7930
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1137 4548 1592 646 1293 2885 1350 1350 2388 2544 1194
MFWKCE 1736 2128 1000 1250 500 1667 3000 1000 8000 4000 3000 5000 3000
MFWKBL 1752 2129 3851 3847 3339 3847 5122 1298 280 280 2056 1812 2056
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 7690 7690 8972 7690 7685 3848 3614 3614 5138 3855 5138
PHDLY2 1757 2134 12840 12850 12816 12840 12850 8990 4372 8980 6430 8995 8990
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32766 32765 32762 32762 32762 32766 32760 32764 32766 32764
POVC22 1786 2163 20 20 41 77 77 75 21 99 50 31 51
POVCLMT2 1787 2164 3776 3711 7395 12702 12702 12424 3890 15559 8836 5701 8891
MAXCRT 1788 2165 25 10 10 25 10 10 45 25 25 25 45
- 518 -
αiF4 βiS22 αiF4 αC8 αiF8 βiS22 αiF8 βiS0.4 βiS0.5 βiS1 βiS8/3000
Motor model 4000 2000 4000HV 2000i 3000 2000HV 3000HV 5000 6000 6000 FS0i
Motor specification 0223 0085 0225 0226 0227 0086 0229 0114 0115 0116 0075-Bxx6
Motor ID No. 273 274 275 276 277 278 279 280 281 282 283
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00000000 00000000 00000000 00100000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000010 00001110 00001010 00001010 00000000 00001110 00001010 00000010 00001010 00001010 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 993 1184 570 1276 787 1446 1222 100 138 312 650
PK2 1853 2041 -4260 -6800 -3578 -6288 -4184 -5822 -5890 -430 -673 -1360 -3831
PK3 1854 2042 -1311 -1331 -1309 -1326 -1325 -1332 -1322 -2463 -1205 -1203 -1299
PK1V 1855 2043 106 242 113 150 113 244 113 7 7 6 164
PK2V 1856 2044 -953 -2172 -1009 -1342 -1009 -2182 -1008 -61 -59 -53 -1476
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3980 3496 3762 2827 3760 3478 3764 -6249 -6462 -7176 5143
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -5130 -5130 0 0 0 0 0 -12850 -12850 -12850 -2570
PVPA 1869 2057 -11789 -3612 0 -3854 -6420 -3612 -6159 0 0 -15420 -5140
PALPH 1870 2058 -180 -3000 0 -1236 -2000 -3000 -1261 0 0 -1000 -3200
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 8010 7282 7282 7282 8010 7282 8010 5826 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32446 32106 32433 32289 32383 32433 32433 32640 32674 32695 32381
POVC2 1878 2063 4029 8275 4184 5994 4807 4185 4184 1603 1178 915 4835
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 11998 24770 12461 17889 14327 12462 12461 4759 3497 2714 14410
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 16384 12288 8192 8192 8192 12288 20480 20480 20480 16384
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1784 2618 1888 2593 1950 2611 1948 1605 1376 1212 2780
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 0 0 0 15000 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 201 692 190 277 369 689 369 22 42 89 226
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 32 0 1032 1552 776 0 782 30 25 1556 1807
DETQLM 1704 2111 5130 2866 0 3880 3870 2866 0 10290 10290 10290 7930
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1443 2459 2573 2380 2103 5149 4191 400 504 881 1442
MFWKCE 1736 2128 2000 5000 4000 4500 3500 3000 6000 0 0 1500 3500
MFWKBL 1752 2129 3338 562 3348 1550 1815 562 1810 0 0 5135 1298
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 6670 3350 5130 3860 0 3352 5150 7690 7690 15400 3858
PHDLY2 1757 2134 8980 8979 8990 8990 0 8989 8990 12820 12820 12840 8990
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32763 32766 32763 32765 32763 32765 32766 32767 32767 32764
POVC22 1786 2163 27 64 31 63 33 64 33 22 16 12 51
POVCLMT2 1787 2164 5069 10913 5676 10709 6053 10854 6042 4104 3015 2340 8896
MAXCRT 1788 2165 45 45 25 25 45 25 25 25 25 25 25
- 519 -
αiS2 αiS8 αiS8 αiS2 αiS12 αiS12 αiS8 αC12 αiS8 αiF12 βiS8/3000
Motor model 6000 4000 4000HV 6000HV 4000 4000HV 6000 2000i 6000HV 3000 FS0i 40A
Motor specification 0218 0235 0236 0219 0238 0239 0232 0241 0233 0243 0075-Bxx6
Motor ID No. 284 285 286 287 288 289 290 291 292 293 294
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00000000 00100000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001110
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001110
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00000010 00001010 00000000 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 552 550 694 497 570 783 460 1875 381 1701 1160
PK2 1853 2041 -2288 -3449 -3858 -2371 -3358 -4294 -1760 -9137 -1749 -6391 -5600
PK3 1854 2042 -1252 -1307 -1318 -1249 -1319 -1333 -1305 -1339 -1305 -1315 -1299
PK1V 1855 2043 48 33 34 48 52 52 53 280 53 192 82
PK2V 1856 2044 -429 -294 -306 -429 -466 -470 -478 -2504 -478 -1721 -738
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -884 -1289 -1240 -884 -815 -808 -794 1516 -794 2204 -1029
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 -12850 0 -12850 0 0
PVPA 1869 2057 -13062 -7685 -7685 -13062 -5898 -5898 -16398 -1804 -16398 -8199 -5131
PALPH 1870 2058 -1000 -2000 -2000 -1200 -3000 -3000 -1000 -2500 -1000 -747 -1600
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 3641
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32415 32609 32596 32416 32534 32530 32520 32289 32548 32520 32671
POVC2 1878 2063 4413 1993 2153 4405 2923 2976 3101 5994 2755 3101 1214
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 13146 5920 6396 13123 8692 8848 9224 17889 8192 9224 3603
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 0 8192 20480 0 8192 8192 8192 8192 8192 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1868 1253 1302 1866 1518 1532 2075 3020 2075 2085 1390
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 15000 0 15000 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 96 562 541 96 696 690 346 350 346 517 452
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1555 519 519 1555 521 521 1284 0 1284 32 1045
DETQLM 1704 2111 11550 7268 7268 11550 6174 6159 10255 2168 10255 0 7930
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1137 2106 5103 2302 1592 4904 801 4150 1600 2388 1442
MFWKCE 1736 2128 3000 4000 4500 2200 2000 2000 1000 12000 1400 2000 7000
MFWKBL 1752 2129 4112 2580 2580 4112 2575 2575 5388 1044 5390 2568 1298
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 7690 5150 5150 7690 6174 6174 10250 5150 10260 0 3858
PHDLY2 1757 2134 7740 8990 8990 7740 8990 8990 12830 8990 12835 0 8990
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32766 32767 32767 32766 32766 32766 32765 32761 32765 32765 32767
POVC22 1786 2163 30 13 14 30 19 20 38 91 38 38 12
POVCLMT2 1787 2164 5554 2501 2702 5544 3672 3738 6857 14518 6857 6924 2224
MAXCRT 1788 2165 25 85 45 10 85 45 85 25 45 85 45
- 520 -
βiS12 βiS12 βiS22 βiS22

αiF12 αC22 αiF22 αiF22 αC30 αiF30 βiS2/4000
Motor model 2000 2000 1500 1500
3000HV 2000i 3000 3000HV 1500i 3000 FS0i
FS0i FS0i 40A FS0i FS0i 40A
Motor specification 0245 0246 0247 0077-Bxx6 0249 0077-Bxx6 0251 0084-Bxx6 0253 0084-Bxx6 0061-Bxx6
Motor ID No. 295 296 297 298 299 300 301 302 303 305 306
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00000000 00100000 00000000 00100000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00001110 00000100
1708 2014 00000000 00000000 00000000 00000000 00000000 00001110 00000000 00000000 00000000 00001110 00000100
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00001010 00000000 00001110 00000000 00001110 00001010 00001110 00001010 00001110 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1200 2320 1750 547 1919 1094 2238 2171 768 4342 360
PK2 1853 2041 -6059 -10593 -6000 -3289 -9132 -6578 -13330 -8178 -4492 -16356 -1920
PK3 1854 2042 -1339 -1347 -1345 -1305 -1346 -1305 -1347 -1329 -1347 -1329 -1237
PK1V 1855 2043 193 271 198 230 197 115 166 280 230 140 78
PK2V 1856 2044 -1727 -2426 -1775 -2054 -1765 -1027 -1486 -2507 -2057 -1254 -698
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 2197 1565 2137 3695 2150 7390 2553 3027 1845 6054 -1089
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 -20500 0 0
PVPA 1869 2057 -8203 -2597 -5136 -3884 -5136 -3862 -1545 -2110 -8465 -2079 -10250
PALPH 1870 2058 -1178 -1942 -2800 -4350 -2824 -2175 -1300 -4691 -1657 -2342 -1000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 8010 7282 7282 7282 3641 7282 7282 7282 3641 6554
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32548 32114 32520 32323 32548 32646 32520 32319 32511 32655 32652
POVC2 1878 2063 2755 8171 3101 5566 2755 1525 3101 5617 3215 1411 1455
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 8192 24454 9224 16603 8192 4511 9224 16756 9565 4189 4317
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 12288 4096 12288 8192 8192 0 8192 8192 4096 0 16384
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2092 2911 2131 3126 2118 1563 1655 3012 2306 1506 1529
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 0 15000 0 15000 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 516 680 929 315 934 630 1630 597 1170 1194 119
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 774 1548 1291 1 787 1282 2059 1025 1032 514 1048
DETQLM 1704 2111 0 2600 0 3940 0 3940 2148 2248 7735 2248 11600
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 4787 3695 3272 1350 6547 1350 6680 3290 1688 3290 1172
MFWKCE 1736 2128 4000 4000 4500 4000 6000 8000 14000 5500 2500 11000 2500
MFWKBL 1752 2129 2320 1046 1301 280 1808 280 539 1032 2829 1032 3358
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 2070 0 3614 0 3614 1054 2580 5140 2580 7192
PHDLY2 1757 2134 0 9000 0 8980 0 4372 9000 8990 8995 4382 8990
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 140 0 120
POVC21 1785 2162 32765 32761 32765 32763 32765 32767 32766 32763 32764 32767 32757
POVC22 1786 2163 39 83 40 60 40 15 23 60 48 14 140
POVCLMT2 1787 2164 6969 13493 7229 10250 7142 2785 4361 10345 8466 2586 2665
MAXCRT 1788 2165 45 45 85 25 45 45 85 25 165 45 25
- 521 -
αiF40 αiF40 βiS2/4000 βiS4/4000 βiS4/4000 αiS22 αiS22 αiS30 αiS30 αiS40 αiS40
Motor model 3000 3000Fan FS0i 40A FS0i FS0i 40A 4000 4000HV 4000 4000HV 4000 4000HV
Motor specification 0257 0257 0061-Bxx6 0063-Bxx6 0063-Bxx6 0265 0266 0268 0269 0272 0273
Motor ID No. 307 308 310 311 312 315 316 318 319 322 323
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00010000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00010000 00000000 00001110 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00000010 00001110 00001110 00001110 00001010 00001010 00001010 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1613 1613 720 400 800 581 709 799 816 712 860
PK2 1853 2041 -7446 -7446 -3840 -1920 -3840 -3844 -4008 -4447 -4681 -4138 -4938
PK3 1854 2042 -1348 -1348 -1237 -1253 -1253 -1337 -1345 -1317 -1348 -1341 -1350
PK1V 1855 2043 191 191 39 112 56 69 76 82 82 92 93
PK2V 1856 2044 -1712 -1712 -349 -1008 -504 -616 -685 -733 -738 -827 -831
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 2216 2216 -2178 -753 -1506 6163 5538 5175 5143 4589 4569
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -2570 -2570 -10245 -7694 -7687 -7687 -7683 -6412 -6412 -5645 -5648
PALPH 1870 2058 -2000 -2000 -500 -2800 -1400 -2000 -1000 -2300 -2300 -3000 -3000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 3277 7282 3641 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32511 32431 32739 32532 32709 32511 32501 32511 32501 32511 32501
POVC2 1878 2063 3215 4212 364 2945 738 3215 3332 3215 3332 3215 3332
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 9565 12545 1079 8758 2189 9565 9912 9565 9912 9565 9912
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 16384 16384 0 20480 0 4096 8192 4096 4096 4096 4096
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1957 2593 764 2178 1089 1627 1810 1836 1847 2073 2083
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 12000 12000 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1839 1839 238 146 292 1216 1093 1470 1460 1701 1693
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1291 1291 815 780 532 519 513 775 775 776 769
DETQLM 1704 2111 5220 5140 11600 7790 7790 6224 6194 6450 6430 5682 5682
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 3041 3041 1172 796 796 2041 4264 1871 5117 1853 5230
MFWKCE 1736 2128 6000 2000 5000 3000 6000 2500 2000 4000 3000 4000 4000
MFWKBL 1752 2129 1560 1553 3358 3392 3392 2580 3092 2574 2574 2063 2063
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 2590 3085 7192 8992 8992 5150 5150 5150 5150 5150 5150
PHDLY2 1757 2134 8990 8990 8990 12864 9024 8990 8990 8990 8990 8988 8988
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 140 140 120 120 120 140 0 140 0 140 0
POVC21 1785 2162 32765 32718 32765 32745 32762 32766 32766 32766 32766 32765 32765
POVC22 1786 2163 33 629 34 294 70 23 28 29 30 38 38
POVCLMT2 1787 2164 6099 10707 666 5407 1352 4214 5218 5369 5432 6846 6908
MAXCRT 1788 2165 165 165 45 25 45 165 85 165 85 165 85
- 522 -
Motor model 3000 3000Fan 3000HVFan 3000HV 2500Fan 2500HVFan 2500Fan 2500 2500HV 2500HVFan 2500
Motor ID No. 324 325 326 327 330 331 334 335 336 337 338
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 01000011 01000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00100000 00000000 00000000 00100000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00000000 00001010 00001010 00000000 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 547 547 705 705 1020 1790 1834 1020 1790 2080 1834
PK2 1853 2041 -3423 -3423 -4855 -4855 -7093 -5915 -7805 -7093 -5915 -8139 -7805
PK3 1854 2042 -1345 -1345 -1348 -1348 -1359 -1359 -1360 -1359 -1359 -1359 -1360
PK1V 1855 2043 69 69 70 70 91 91 115 91 91 115 115
PK2V 1856 2044 -622 -622 -628 -628 -819 -819 -1026 -819 -819 -1026 -1026
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 6099 6099 6039 6039 4632 4636 3699 4632 4636 3699 3699
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 31979 31979 31979 31979 21 21 21 21 21 21 21
PDDP 1866 2054 3 3 3 3 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -5638 -5638 -5638 -5638 -4368 -3846 -3090 -4368 -3846 -3088 -3090
PALPH 1870 2058 -1000 -1000 -1000 -1000 -1359 -900 -2700 -1359 -900 -3000 -2700
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32558 32348 32371 32554 32309 32309 32309 32310 32474 32309 32309
POVC2 1878 2063 2627 5245 4967 2680 5734 5734 5734 5728 3672 5734 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 7810 15639 14807 7968 27346 27346 27346 15662 15982 27346 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 4096 4096 0 0 20480 12288 12288 20480 12288 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1439 2037 2057 1454 2848 2848 3013 1960 2033 3013 2712
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 10000 0 0 10000 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 3312 3312 3279 3279 4589 4423 5973 4589 4423 5973 5973
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 519 519 519 519 776 1291 1290 776 1291 1291 1290
DETQLM 1704 2111 6174 6174 6174 6174 3787 0 0 3787 0 3428 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 2046 2046 4861 4861 3520 6952 3518 3520 6952 6729 3518
MFWKCE 1736 2128 6500 6500 2500 2500 6500 2000 4000 6500 2000 4000 4000
MFWKBL 1752 2129 2063 2063 2068 2068 1297 1549 1298 1297 1549 1551 1298
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 5150 5150 5150 5150 2570 0 3092 2570 0 2575 3092
PHDLY2 1757 2134 8990 8990 8990 8990 8970 0 12826 8970 0 8984 12826
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 140 140 140 106 140 140 140
POVC21 1785 2162 32754 32739 32738 32754 32745 32745 32745 32750 32759 32745 32745
POVC22 1786 2163 174 365 373 178 292 292 292 223 112 292 292
POVCLMT2 1787 2164 3300 6608 6736 3366 13952 13952 13952 6581 6752 13952 13952
MAXCRT 1788 2165 365 365 185 185 365 185 365 365 185 185 365
- 523 -
αiS200 αiS2000 αiS300 αiS300 αiS500 αiS500 αiS1000

Motor model 2500HV 2000HV 2000 2000HV 2000 2000HV 2000HV
Motor specification 0289 0091 0292 0293 0295 0296 0298
Motor ID No. 339 340 342 343 345 346 348
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 01000011 00000011 01000011 00000011 01000011 01000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000001 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00011110 00001010 00001010 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 2080 643 1659 1327 2660 2255 840
PK2 1853 2041 -8139 -3600 -8045 -7279 -10235 -10049 -5329
PK3 1854 2042 -1359 -1358 -1354 -1356 -1355 -1356 -1361
PK1V 1855 2043 115 502 114 114 134 134 234
PK2V 1856 2044 -1026 -4500 -1025 -1025 -1199 -1199 -2096
PK3V 1857 2045 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3699 843 3709 3703 3164 3164 1811
BLCMP 1860 2048 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21
PDDP 1866 2054 1894 3787 1894 3787 1894 3787 3787
PHYST 1867 2055 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 -12825 0 0 0 0 0
PVPA 1869 2057 -3088 -2120 -3081 -3846 -2068 -2070 -2320
PALPH 1870 2058 -3000 -2800 -700 -900 -2600 -2700 -2500
PPBAS 1871 2059 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0
POVC1 1877 2062 32309 32309 32391 32391 32309 32309 32309
POVC2 1878 2063 5734 5734 4714 4714 5734 5734 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4
POVCLMT 1893 2065 27346 27346 23263 23263 27346 27346 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0
AALPH 1967 2074 12288 12288 12288 12288 12288 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0
RTCURR 1979 2086 2712 2893 2386 2483 2980 2980 2834
TDPLD 1980 2087 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0
TRQCST 1998 2105 5973 6221 10871 10871 15096 15096 28573
LP24PA 1999 2106 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0
MGSTCM 1703 2110 1291 2068 1296 1296 1296 1293 1296
DETQLM 1704 2111 3428 1430 0 0 0 0 3172
AMRDML 1705 2112 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0
NINTCT 1735 2127 6729 3449 3817 7634 4175 8341 8637
MFWKCE 1736 2128 4000 4200 7000 5000 4000 4500 6000
MFWKBL 1752 2129 1551 1060 1301 1298 1041 788 1047
LP2GP 1753 2130 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0
PHDLY1 1756 2133 2575 1297 2574 2574 2069 2324 2580
PHDLY2 1757 2134 8984 12828 12814 12814 8981 8984 8985
DGCSMM 1782 2159 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0
OVCSTP 1784 2161 140 140 140 140 140 140 140
POVC21 1785 2162 32745 32745 32738 32738 32745 32745 32745
POVC22 1786 2163 292 292 375 375 292 292 292
POVCLMT2 1787 2164 13952 13952 13952 13952 13952 13952 13952
MAXCRT 1788 2165 185 0 365 365 365 365 365
- 524 -
LiS300 LiS600 LiS900 LiS1500 LiS1500 LiS3000 LiS3000 LiS3000 LiS4500 LiS4500 LiS4500
Motor model A1/4 A1/4 A1/4 B1/4 B1/4 B2/2 B2/2 B2/4 B2/2HV B2/2 B2/2
(200V) (200V) (200V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V)
Motor specification 0441-B200 0442-B200 0443-B200 0444-B210 0444-B210 0445-B110 0445-B110 0445-B210 0446-B010 0446-B110 0446-B110
Motor ID No. 351 353 355 357 358 360 361 362 363 364 365
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1751 2211 00000000 00000000 00000000 00000000 00001000 00000000 00001000 00000000 00001000 00001000 00001000
2713 2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1968 1868 1594 1512 409 961 602 324 2590 2834 802
PK2 1853 2041 -7138 -6536 -6162 -11488 -2068 -5781 -3127 -4472 -6505 -10862 -4726
PK3 1854 2042 -2618 -2618 -2618 -2647 -2689 -2667 -1330 -2660 -2697 -2696 -2696
PK1V 1855 2043 16 9 13 19 19 14 14 16 11 10 10
PK2V 1856 2044 -217 -122 -179 -260 -260 -194 -194 -214 -149 -131 -131
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -8755 -9339 -6367 -4371 -4371 -5866 -5866 -5321 -7658 -8705 -8705
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -6400 -6400 -6400 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 5826 6554 7282 7282 7282 7282 7282 7282 6554 5462 5462
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32720 32720 32721 32698 32698 32711 32711 32698 32714 32707 32707
POVC2 1878 2063 596 596 583 873 873 719 719 873 681 758 758
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 589 589 1326 2590 2590 2131 2131 2590 1549 1199 1199
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 -24576 -8192 28672 0 0 0 20480 0 20480 20480 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 564 564 847 1184 1184 1074 1074 1184 915 805 805
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 68 137 137 227 227 502 502 455 884 1005 1005
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 793 792 786 0 0 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 25 45 45 45 45 45 45 85 45 85 85
- 525 -
Motor model B2/2Hv B2/2 B2/2 B2/4 B2/2Hv B2/2 B2/2 B2/4 B2/2 B2/2 B2/4
(400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (200V) (400V) (200V)
Motor ID No. 367 368 369 370 371 372 373 374 376 377 378
1808 2003 00000000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000110 00000000 00000000 00000000 00000000 00000000 00001000 00001000 00000110 00000010 00001010
1708 2014 00000110 00000000 00000000 00000000 00000000 00000000 00001000 00001000 00000110 00000010 00001010
1750 2210 00000100 00000100 00000100 00000000 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1751 2211 00001000 00000000 00001000 00000000 00001000 00001000 00001000 00001000 00000000 00001000 00000000
2713 2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1469 961 766 1401 1742 848 1123 946 1240 834 1483
PK2 1853 2041 -9936 -5255 -4195 -10722 -6205 -5532 -6625 -6400 -7877 -4701 -7099
PK3 1854 2042 -1330 -2660 -2696 -2660 -2697 -2696 -2696 -1331 -2660 -1330 -2660
PK1V 1855 2043 7 13 13 15 9 8 7 8 12 9 10
PK2V 1856 2044 -96 -169 -169 -202 -117 -103 -92 -101 -158 -128 -141
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -11870 -6746 -6746 -5642 -9690 -11014 -12391 -11240 -7199 -8929 -8099
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -7680 0 0 0 0 -7936 0 -7680 0 -9216 0
PVPA 1869 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 4369 7282 7282 7282 5462 4551 4046 4046 5917 5259 4855
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32749 32711 32711 32708 32714 32707 32709 32687 32707 32709 32696
POVC2 1878 2063 232 719 719 753 680 765 739 1010 758 737 895
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 688 2131 2131 2233 1075 832 858 799 1199 947 1151
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 0 0 0 20480 -24576 0 20480 0 20480 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 610 1074 1074 1184 763 671 671 658 805 716 789
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1768 1005 1005 911 1768 2010 2261 2051 2010 2261 2051
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 85 85 85 165 85 165 185 365 165 185 365
- 526 -
Motor model C1/2 C1/2 C2/2 C2/2 C2/2HV C2/2 C2/2 C2/3HV C2/2 C2/3 C3/2
(200V) (400V) (200V) (400V) (400V) (200V) (400V) (400V) (200V) (200V) (200V)
Motor ID No. 380 381 384 385 387 388 389 391 392 394 396
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00000000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001010 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001010 00000000 00000000
1750 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1751 2211 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00000000 00001000
2713 2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1346 636 587 910 605 431 702 989 1704 478 158
PK2 1853 2041 -6448 -3246 -3839 -4971 -3361 -3377 -4479 -6312 -13440 -3379 -1761
PK3 1854 2042 -2695 -2695 -2696 -2696 -2694 -2695 -2695 -2695 -2663 -2657 -2695
PK1V 1855 2043 9 9 8 7 10 10 9 10 7 10 10
PK2V 1856 2044 -126 -126 -110 -98 -136 -136 -121 -131 -87 -128 -141
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -9048 -9048 -10377 -11674 -8363 -8363 -9409 -8681 -13022 -8861 -8077
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 5462 5462 6372 5663 7282 7282 6877 7282 4855 7282 7282
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32708 32708 32729 32728 32723 32723 32730 32730 32729 32732 32722
POVC2 1878 2063 749 749 489 494 560 560 474 471 483 452 582
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 1184 1184 1112 879 1661 1661 1312 1396 621 1340 1719
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 0 0 -16384 0 -24576 -24576 0 0 0 0 -24576
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 801 801 776 689 948 948 843 869 579 852 964
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 741 741 2087 2348 2087 2087 2348 3104 4656 3168 1865
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 85 85 165 185 85 165 185 185 365 365 165
- 527 -
LiS10000 LiS17000 LiS17000 DiS22 DiS22 DiS85 DiS85 DiS110 DiS110 DiS260 DiS260
Motor model C3/2 C3/2 C3/2 /600 /600 /400 /400 /300 /300 /300 /300
(400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V)
Motor specification 0457-B110 0459-B110 0459-B110 0482-B10x 0482-B10x 0483-B20x 0483-B20x 0484-B10x 0484-B10x 0484-B30x 0484-B30x
Motor ID No. 397 400 401 421 422 423 424 425 426 427 428
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1751 2211 00000000 00001000 00000000 00001000 00001000 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 10000000 10000000 10000000 10000110 10000110 10000100 10000100 10000100 10000100 10000100 10000100
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 839 2182 253 621 374 344 172 156 78 313 157
PK2 1853 2041 -4103 -8540 -3693 -2202 -1042 -2368 -1184 -1045 -523 -2146 -1073
PK3 1854 2042 -2695 -2696 -2696 -2946 -2946 -2491 -2491 -2448 -2448 -2485 -2485
PK1V 1855 2043 9 7 7 157 157 242 242 420 420 326 326
PK2V 1856 2044 -125 -99 -99 -1410 -1410 -2164 -2164 -3763 -3763 -2919 -2919
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -9086 -11497 -11497 5982 5982 3897 3897 2241 2241 2889 2889
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 6877 6887 6877 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 120 120 120 0 0 0 0 0 0 0 0
POVC1 1877 2062 32720 32711 32711 32689 32689 32683 32683 32682 32682 32682 32682
POVC2 1878 2063 597 709 709 988 988 1069 1069 1069 1069 1069 1069
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 1358 981 981 2826 2826 3172 3172 3173 3173 3173 3173
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 20480 20480 20480 20480 0 0 0 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 857 729 729 1237 1237 1310 1310 1310 1310 1310 1310
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 2098 4197 4197 448 448 1167 1167 1510 1510 3570 3570
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 1793 1793 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 8568 25660 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 185 365 365 25 25 45 45 85 85 85 85
- 528 -
DiS260 DiS260 DiS370 DiS370 DiS1200/ DiS1200/ DiS1500/ DiS1500/ DiS2100/ DiS2100/ DiS3000/
Motor model /600 /600 /300 /300 250 250 200 200 150 150 150
(200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V)
Motor specification 0484-B31x 0484-B31x 0484-B40x 0484-B40x 0485-B50x 0485-B50x 0486-B30x 0486-B30x 0487-B30x 0487-B30x 0487-B40x
Motor ID No. 429 430 431 432 435 436 437 438 439 440 441
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00001000 00001000 00000000 00000000 00001000 00001000 00000000 00000000 00000000 00000000 00000000
1708 2014 00001000 00001000 00000000 00000000 00001000 00001000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10000000
PK1 1852 2040 571 321 478 239 517 291 640 360 637 359 817
PK2 1853 2041 -4138 -2327 -3338 -1669 -3361 -1891 -4779 -2688 -4762 -2679 -6084
PK3 1854 2042 -2573 -2573 -2515 -2515 -2408 -2408 -2619 -2619 -2620 -2620 -2616
PK1V 1855 2043 240 213 264 264 430 382 839 746 1760 1565 1635
PK2V 1856 2044 -2146 -1907 -2361 -2361 -3850 -3422 -7513 -6678 -15770 -14017 -14643
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3931 4422 3572 3572 2190 2464 1122 1263 535 602 576
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 1870 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 5352 4758 7282 7282 5648 5020 7282 6473 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32679 32679 32705 32705 32677 32678 32682 32700 32682 32682 32682
POVC2 1878 2063 1111 1111 782 782 1113 1130 1069 845 1069 1069 1069
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 1710 1351 2322 2322 1940 1529 3173 2507 3173 3173 3173
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 0 0 0 0 0 0 0 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 963 856 1121 1121 1028 914 1310 1165 1310 1310 1310
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 4857 5464 6020 6020 21246 23902 20598 23173 25635 28839 3667
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 0 0 0 0 0 0
DETQLM 1704 2111 0 0 0 0 0 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 0 0 0 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 165 185 85 85 165 185 165 185 165 185 165
- 529 -
DiS3000/ DiS85 DiS110 DiS260

Motor model 150 /1000 /1000 /1000
(400V) (200V) (200V) (200V)
Motor specification 0487-B40x 0483-B22x 0484-B12x 0484-B32x
Motor ID No. 442 443 445 447
1808 2003 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000
1707 2013 00000000 00000001 00000001 00000001
1708 2014 00000000 00000000 00000000 00000000
1750 2210 00000100 00000100 00000100 00000100
1751 2211 00000000 00001000 00001000 00001000
2713 2300 10000100 10000110 10000110 10000110
2714 2301 10000000 00000000 00000000 00000000
PK1 1852 2040 459 480 301 290
PK2 1853 2041 -3422 -1395 -1001 -916
PK3 1854 2042 -2616 -3002 -3024 -3016
PK1V 1855 2043 1453 220 292 243
PK2V 1856 2044 -13016 -1971 -2614 -2178
PK3V 1857 2045 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235
POA1 1859 2047 648 4278 3227 3871
BLCMP 1860 2048 0 0 0 0
DPFMX 1861 2049 0 0 0 0
POK1 1862 2050 956 956 956 956
POK2 1863 2051 510 510 510 510
RESERV 1864 2052 0 0 0 0
PPMAX 1865 2053 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319
EMFCMP 1868 2056 0 0 0 0
PVPA 1869 2057 0 -12846 -20535 -10266
PALPH 1870 2058 0 -2731 -1183 -1821
PPBAS 1871 2059 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0
POVC1 1877 2062 32682 32346 32434 32580
POVC2 1878 2063 1069 5276 4174 2354
TGALMLV 1892 2064 4 4 4 4
POVCLMT 1893 2065 3173 15735 12437 6423
PK2VAUX 1894 2066 0 0 0 0
FILTER 1895 2067 0 0 0 0
FALPH 1961 2068 0 0 0 0
VFFLT 1962 2069 0 0 0 0
ERBLM 1963 2070 0 0 0 0
PBLCT 1964 2071 0 0 0 0
SFCCML 1965 2072 0 0 0 0
PSPTL 1966 2073 0 0 0 0
AALPH 1967 2074 0 20480 8192 8192
OSCTPL 1970 2077 0 0 0 0
PDPCH 1971 2078 0 0 0 0
PDPCL 1972 2079 0 0 0 0
DPFEX 1973 2080 0 0 0 0
DPFZW 1974 2081 0 0 0 0
BLENDL 1975 2082 0 0 0 0
MOFCTL 1976 2083 0 0 0 0
RTCURR 1979 2086 1310 2919 2595 1865
TDPLD 1980 2087 0 0 0 0
MCNFB 1981 2088 0 0 0 0
BLBSL 1982 2089 0 0 0 0
ROBSTL 1983 2090 0 0 0 0
ACCSPL 1984 2091 0 0 0 0
ADFF1 1985 2092 0 0 0 0
VMPK3V 1986 2093 0 0 0 0
BLCMP2 1987 2094 0 0 0 0
AHDRTL 1988 2095 0 0 0 0
RADUSL 1989 2096 0 0 0 0
SMCNT 1990 2097 0 0 0 0
DEPVPL 1991 2098 0 0 0 0
ONEPSL 1992 2099 400 400 400 400
INPA1 1993 2100 0 0 0 0
INPA2 1994 2101 0 0 0 0
DBLIM 1995 2102 0 0 0 0
ABVOF 1996 2103 0 0 0 0
ABTSH 1997 2104 0 0 0 0
TRQCST 1998 2105 4125 1281 2175 4784
LP24PA 1999 2106 0 0 0 0
VLGOVR 1700 2107 0 0 0 0
RESERV 1701 2108 0 0 0 0
BELLTC 1702 2109 0 0 0 0
MGSTCM 1703 2110 0 2313 1027 1537
DETQLM 1704 2111 0 11647 14212 11620
AMRDML 1705 2112 0 0 0 0
NFILT 1706 2113 0 0 0 0
NINTCT 1735 2127 0 0 0 0
MFWKCE 1736 2128 0 10500 15000 9800
MFWKBL 1752 2129 0 278 533 287
LP2GP 1753 2130 0 0 0 0
LP4GP 1754 2131 0 0 0 0
LP6GP 1755 2132 0 0 0 0
PHDLY1 1756 2133 0 0 0 0
PHDLY2 1757 2134 0 0 0 0
DGCSMM 1782 2159 0 0 0 0
TRQCUP 1783 2160 0 0 0 0
OVCSTP 1784 2161 0 0 0 0
POVC21 1785 2162 0 0 0 0
POVC22 1786 2163 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0
MAXCRT 1788 2165 185 45 85 165
- 530 -
6.3 PARAMETERS FOR HRV1 CONTROL (FOR Series 0i-A)

August, 2007
9066 series (Series 0i-A)
NOTE
The parameters listed below cannot be loaded
automatically.
In parameter No. 2020 for entering a motor ID
number, enter an appropriate number (15, for
example), and perform automatic loading. Then,
overwrite these parameters manually.
- 531 -
Motor model α1 α2 αC4 α4 α4 αC8 α8 α8 βM0.5 βM1 αC12 α12

5000i 5000i 3000i 4000i 4000HVi 2000i 3000i 3000HVi 2000i 3000i
Motor specification 0202 0205 0221 0223 0225 0226 0227 0229 0115 0116 0241 0243
Motor ID No.
Symbol 0iM-A
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00100000 00000000 00100000 00100000 00000000 00000000 00100000 00000000 00000000 00100000 00100000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00000010 00000010 00001000 00000010 00000000 00001010 00001010 00000000 00000010 00000010 00000010 00000000
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 672 680 926 659 525 1096 712 886 141 398 3809 1072
PK2 2041 -2294 -2247 -4063 -2463 -2056 -4638 -3187 -3174 -511 -1137 -8197 -3835
PK3 2042 -2514 -2568 -2619 -2623 -2619 -2651 -2651 -2645 -2415 -2388 -2679 -2630
PK1V 2043 66 76 115 106 113 150 113 113 7 6 280 192
PK2V 2044 -594 -680 -1034 -953 -1009 -1342 -1009 -1008 -59 -53 -2504 -1721
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 6384 5578 3670 3980 3762 2827 3760 3764 -6462 -7176 1516 2204
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 -20485 0 0 0 0 0 0 -12850 -12850 0 0
PVPA 2057 0 -10256 -5915 -11789 0 -3854 -6418 -6159 0 -11530 -1804 -8199
PALPH 2058 0 -3300 -1500 -180 0 -1236 -3000 -1261 0 -1000 -2500 -747
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 8010 7282 7282 8010 8010 6918 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32692 32635 32590 32610 32591 32434 32579 32579 32674 32695 32317 32552
POVC2 2063 948 1664 2225 1979 2216 4170 2363 2358 1178 915 5644 2702
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 5739 10085 13493 11998 12461 17889 14327 12461 3497 2714 17889 9224
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 0 4096 12288 8192 20480 8192 12288 16384 20480 20480 8192 8192
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 1234 1636 1892 1784 1888 2593 1950 1948 1376 1212 3020 2085
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 12000 0 15000 15000 0 0 15000 0 0 15000 15000
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 72 109 190 201 190 277 369 369 42 89 350 517
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 32 32 1289 32 1032 1552 786 782 30 30 0 32
DETQLM 2111 7710 6460 3900 5130 0 3880 5180 0 10290 10290 2168 0
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 1188 1276 2544 1443 2573 2380 2103 4191 1009 1763 4150 2388
MFWKCE 2128 570 855 5000 2000 4000 4500 1500 6000 0 0 12000 2000
MFWKBL 2129 3211 3211 1812 3338 3348 1550 1815 1810 0 0 1044 2568
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 2571 2565 3855 6670 0 3860 5140 0 7690 11560 5150 0
PHDLY2 2134 12850 12850 5155 5140 0 5150 5145 0 12820 12880 5150 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 25 25 25 45 25 25 45 25 25 25 25 85
- 532 -
Motor model α12 αC22 α22 α22 αC30 α30 α40 α40
3000HVi 2000i 3000i 3000HVi 1500i 3000i 3000i 3000iFan
Motor specification 0245 0246 0247 0249 0251 0253 0257 0258
Motor ID No.
Symbol 0iM-A
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00100000 00000000 00100000 00100000 00000000 00000000 00100000 00100000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00000000 00001010 00000000 00000000 00001010 00001010 00000010 00000010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1044 1755 1458 1532 2644 485 1047 1047
PK2 2041 -3677 -6536 -5416 -5641 -10345 -1896 -4102 -4102
PK3 2042 -2679 -2694 -2690 -2692 -2695 -2694 -2696 -2696
PK1V 2043 193 271 198 197 166 283 235 235
PK2V 2044 -1727 -2426 -1775 -1765 -1486 -2531 -2107 -2107
PK3V 2045 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 2197 1565 2137 2150 2553 1499 1801 1801
BLCMP 2048 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0
PVPA 2057 -8214 -2597 -5136 -4392 -1545 -5181 -2572 -2572
PALPH 2058 -2350 -1942 -2800 -2824 -1300 -1231 -2462 -2462
PPBAS 2059 0 0 0 0 0 0 0 0
TQLIM 2060 7282 8010 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0
POVC1 2062 32550 32348 32542 32545 32632 32369 32480 32264
POVC2 2063 2719 5248 2820 2786 1704 4989 3600 6300
TGALMLV 2064 4 4 4 4 4 4 4 4
POVCLMT 2065 8192 24454 9224 8192 9224 14489 14489 19003
PK2VAUX 2066 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0
AALPH 2074 12288 8192 8192 8192 8192 8192 8192 8192
OSCTPL 2077 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0
RTCURR 2086 2092 2911 2131 2118 1655 2838 2409 3191
TDPLD 2087 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0
DBLIM 2102 15000 0 15000 15000 0 0 15000 15000
ABVOF 2103 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0
TRQCST 2105 516 680 929 934 1630 951 1494 1494
LP24PA 2106 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0
MGSTCM 2110 774 1548 1291 787 2059 1030 1544 1544
DETQLM 2111 0 2600 0 0 2148 7735 5140 5140
AMRDML 2112 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0
NINTCT 2127 4787 3695 3272 6547 6680 1688 3041 3041
MFWKCE 2128 4000 4000 4500 6000 14000 2031 1625 1625
MFWKBL 2129 2320 1046 1301 1808 539 2829 1553 1553
LP2GP 2130 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0
PHDLY1 2133 0 2070 0 0 1054 5140 3087 3087
PHDLY2 2134 0 5160 0 0 5160 5155 5150 5150
DGCSMM 2159 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 140 140 140
POVC21 2162 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0
MAXCRT 2165 45 45 85 45 85 135 135 135
- 533 -
APPENDIX
A.ANALOG SERVO INTERFACE
B-65270EN/07 APPENDIX SETTING PROCEDURE
A ANALOG SERVO INTERFACE SETTING

PROCEDURE
(1) Overview
Appendix A describes the method of setting parameters required when
using the analog servo function with an analog servo interface unit.
CAUTION
1 For the CNCs that support this function, contact
FANUC.
2 For analog servo axes, only the feed-forward,
backlash compensation, pitch error compensation,
and position gain switch functions can be used as
digital servo functions.

(Series 15i-B,16i-B,Power Mate i)

(1) Setting start: Switch on the CNC power from an emergency stop.
(2) Set up the FSSB. Switch the power off and on again.
(3) Initialize the servo parameters. Switch the power off and on
again.
(4) Enable the analog servo interface function. Switch the power off
and on again. Now setting is completed.
(4) FSSB setting

(a) Connecting the analog servo interface unit requires that the FSSB
be set up manually. (The FSSB setting screen cannot be used.)
#7 #6 #5 #4 #3 #2 #1 #0
1090 (FS15i) FMD
1902 (FS30i,16i)
FMD (#0) Specifies the FSSB set mode as follows:
0: Automatic setting mode
1: Manual setting mode ← To be set
- 537 -
A. ANALOG SERVO INTERFACE
SETTING PROCEDURE APPENDIX B-65270EN/07
(b) Directly enter all parameters listed in the following table.

Before doing this, understand the meaning of each parameter
sufficiently. For detailed descriptions about parameter setting,
refer to the respective CNC Connection Manuals and Parameter
Manuals. Analog and digital servo axes can be used together as
shown in the reference examples below.
Parameter number
Meaning
FS15i FS16i, PMi FS30i
1023 1023 1023 Servo axis number for each axis
1093#6, #7 1905#6, #7 1905#6, #7, #1, #2 Selection of interface unit used
1080 to 1089 1910 to 1919 14340 to 14357
Conversion table value for slave number
1120 to 1129 1970 to 1979 14358 to 14375
1094 1936 1936 Connector number for interface unit 1
1095 1937 1937 Connector number for interface unit 2
- - 1938 Connector number for interface unit 3
- - 1939 Connector number for interface unit 4
Conversion table value for connector number of
- - 14376 to 14383
interface unit 1
- - 14384 to 14391
interface unit 2
- - 14392 to 14400
interface unit 3
- - 14401 to 14407
interface unit 4
1100 to 1109 Conversion table value for number of slave connected
- -
1130 to 1139 to 1st axis card on additional-axis board
1110 to 1119 Conversion table value for number of slave connected
- -
1140 to 1149 to 2nd axis card on additional-axis board
Conversion table value for slave number on
- - 14408 to 14425
additional-axis board
- - 14444 to 14451
interface unit 1 on additional-axis board
- - 14452 to 14459
interface unit 2 on additional-axis board
- 538 -
NOTE
1 The FSSB settings for the analog servo interface
unit are also used for the separate detector
interface unit.
(Bits 6, 7, 1, and 2 of No. 1905 (Series 30i, 16i,
etc.) or bits 6 and 7 of No. 1093 (Series 15i) are
shared.)
2 The slave number of an analog servo axis must be
added to behind the last slave number of the units
actually connected to the FSSB line. (See the
setting examples provided below.)
3 With the FS15i, 16i, and PMi, when an analog
servo interface unit is used, HRV3 control
(high-speed HRV current control) cannot be used.
4 With the FS30i, up to two interface units (separate
detector interface unit and (or) analog servo
interface unit) can be connected per FSSB line.
Therefore, the first and second interface units are
connected to the FSSB1 line, and the third and
fourth interface units are connected to the FSSB2
line.
With the FS15i, 16i, and PMi, up to two units
(separate detector interface unit, analog servo
interface unit, FSSB I/O unit, and (or) servo check
interface unit) can be connected to the entire FSSB
line of one axis card.
- 539 -
(Reference)
FSSB setting example where an analog servo interface unit is
used
[Setting example 1: Two analog servo axes]

Let the analog servo interface unit be slave 1. Assume that
analog amplifiers are connected behind the analog servo interface
unit, and let them be slaves 2 and 3 sequentially.
FSSB X-axis
JV11L
Analog servo Analog amplifier 1
interface unit 1
Slave 2
(Basic unit) JV12L Y-axis

Analog amplifier 2
CNC
Slave 1 Slave 3
Parameter No.
1080 1081 1082 1083 1084 1085 1086 1087 1088 1089
(FS15i)
Parameter No.
1910 1911 1912 1913 1914 1915 1916 1917 1918 1919
(FS16i, PMi)
Set value 16 0 1 40 40 40 40 40 40 40
Parameter No.
14340 14341 14342 14343 to 14357
(FS30i)
Set value 64 0 1 -96
Parameter No.
No.1023 No.1093 No.1094 No.1095
(FS15i)
Parameter No.
(FS16i, PMi) No.1023 No.1905 No.1936 No.1937
(FS30i)
X axis 1 01000000 0 0
Y axis 2 01000000 1 0
Parameter No.
14376 14377 14378 to 14407
(FS30i)
Set value 0 1 32
- 540 -
[Setting example 2: One digital servo axis + one analog servo axis]
The digital servo amplifier and analog servo interface unit are
slaves 1 and 2, as in the sequence in which they are connected to
the FSSB. Assuming that the axis connected to the analog servo
amplifier is behind the analog servo interface unit, it is slave 3.
FSSB X-axis
Digital servo amplifier
Slave 1
CNC FSSB
Analog servo
interface unit 1 JV11L Y-axis
Analog amplifier 1
(Basic unit) Slave 3
Slave 2
Parameter No.
1080 1081 1082 1083 1084 1085 1086 1087 1088 1089
(FS15i)
Parameter No.
1910 1911 1912 1913 1914 1915 1916 1917 1918 1919
(FS16i, PMi)
Set value 0 16 1 40 40 40 40 40 40 40
Parameter No.
14340 14341 14342 14343 to 14357
(FS30i)
Set value 0 64 1 -96
Parameter No.
No.1023 No.1093 No.1094 No.1095
(FS15i)
Parameter No.
(FS16i, PMi) No.1023 No.1905 No.1936 No.1937
(FS30i)
X axis 1 00000000 0 0
Y axis 2 01000000 0 0
Parameter No.
14376 14377 to 14407
(FS30i)
Set value 0 32
- 541 -
[Setting example 3: Five analog servo axes + two digital servo axes]
The first analog servo interface unit (including expansion) is
slave 1, two digital servo amplifiers are slaves 2 and 3, the
second analog servo interface unit is slave 4, as in the sequence
in which they are connected to the FSSB. Assuming that the
analog amplifiers are connected behind the analog servo interface
unit, they are slaves 5 to 9.
JV11L X-axis
FSSB Analog servo
Analog amplifier 1
interface unit
Slave 5
(Basic unit) JV12L Y-axis
CNC ユニト１
Slave 1 Analog amplifier 2
Slave 6
JV13L Z-axis
Analog servo Analog amplifier 3
FSSB
interface unit
Slave 7
(Expansion unit) JV14L A-axis
Analog amplifier 4
Slave 8
B-axis
Slave 2
Digital servo amplifiers
(two axes) Slave 3
FSSB C-axis
Analog servo U-axis

interface unit JV11L
Analog amplifier 5
(Basic unit)
Slave 9
Slave 4
Parameter No.
1080 1081 1082 1083 1084 1085 1086 1087 1088 1089
(FS15i)
Parameter No.
1910 1911 1912 1913 1914 1915 1916 1917 1918 1919
(FS16i, PMi)
Set value 16 4 5 48 0 1 2 3 6 40
Parameter No. 14349 to

14340 14341 14342 14343 14344 14345 14346 14347 14348 14357
(FS30i)
Set value 64 4 5 -56 0 1 2 3 6 -96
Parameter No.
No.1023 No.1093 No.1094 No.1095
(FS15i)
Parameter No.
No.1023 No.1905 No.1936 No.1937
(FS16i, PMi), (FS30i)
X axis 1 01000000 0 0
Y axis 2 01000000 1 0
Z axis 3 01000000 2 0
A axis 4 01000000 3 0
B axis 5 00000000 0 0
C axis 6 00000000 0 0
U axis 7 10000000 0 0
Parameter No. 14380 14385

14376 14377 14378 14379 to 14383 14384 to 14407
(FS30i)
Set value 0 1 2 3 32 6 32
- 542 -
(5) Servo parameter initialization

For axes connected to an analog servo circuit, initialize the servo
parameters as listed below.
Parameter number
Name Set value
FS15i FS30i,16i, etc.
1804 2000 Initialization bit 00000000
50 (for HRV1)
1874 2020 Motor ID number
252 (for HRV2)
1806 2001 AMR 00000000
1820 1820 CMR
Perform the same initialization as for digital servo according to
1977 2084 FFG (numerator)
your machine tool.
1978 2085 FFG (denominator)
1879 2022 Direction of movement 111 (counterclockwise) or −111 (clockwise)
Specify the number of pulses per motor revolution (after FFG) in
1896 1821 Reference counter
the same manner as for the digital servo circuit.
Set value = 1536.797 × E
Number of velocity
1876 2023 where E is the voltage (V) that corresponds to a velocity
pulses
command of 1000 min-1.
Number of position Specify the number of pulses per motor revolution (before FFG)
1891 2024
pulses in the same manner as for the digital servo circuit.
NOTE
Although difference in HRV setting is not directly
related to analog servo axes, they must be
initialized with the same HRV setting by reason of
the relationship with the settings of other digital
servo axes.
The Series 30i does not support HRV1 control, so
it is necessary to perform initialization with the
motor ID number (252) for HRV2.
(6) Setting the analog servo function
To enable the analog servo function, set the following parameters for
the axes to be connected to an analog servo circuit. (It is also
necessary to enable the dummy serial feedback function.)
#7 #6 #5 #4 #3 #2 #1 #0
1953 (FS15i) ANALOG DMY
2009 (FS30i,16i)
DMY (#0) The serial feedback dummy function is:
0: Not used
ANALOG (#4) The analog servo interface function is:
0: Not used
1788 (FS15i) Maximum amplifier current

2165 (FS30i,16i)
Specify 0 for the axis to be connected to an analog servo circuit.
- 543 -
B. PARAMETERS SET WITH
VALUES IN DETECTION UNITS APPENDIX B-65270EN/07
B PARAMETERS SET WITH VALUES IN

DETECTION UNITS
If the detection unit is changed with a CMR or flexible feed gear, it is
also necessary to change the parameters that are set with values in
detection units. This appendix lists these parameters.
For details of these parameters, refer to the respective CNC parameter
manuals.
Appendix B, "PARAMETERS SET WITH VALUES IN

DETECTION UNITS", consists of the following sections:
B.1 PARAMETERS FOR Series 15i...............................................545

B.2 PARAMETERS FOR Series 16i, 18i, 21i, AND 0i..................547
B.3 PARAMETERS FOR THE Power Mate i ................................549
B.4 PARAMETERS FOR Series 30i, 31i, AND 32i.......................551
- 544 -
B.PARAMETERS SET WITH
B-65270EN/07 APPENDIX VALUES IN DETECTION UNITS
B.1 PARAMETERS FOR Series 15i
No. Description
1718 For vibration damping control : position pulses conversion coefficient
1729 Dual position feedback function : alarm detection level of Semi-Full error
1730 Variable proportional gain function in the stop state : stop judgement level
1827 Effective area (in-position check) for individual axis
1828 Position error limit for individual axis during movement
1829 Position error limit for individual axis at stop
1830 Position error limit for individual axis with servo off
1832 Position error limit for individual axis with feed at stop
1837 Position error limit during rigid tapping movement
1841 Servo error amount within which reference position return is assumed to be possible
1843 Position error limit with torque limit skipped
1844 Grid shift for reference position shift function
1846 Distance for starting second stage compensation in smooth backlash compensation
1847 Distance for ending second stage compensation in smooth backlash compensation
1848 First stage compensation value in smooth backlash compensation
1849 Backlash compensation for individual axis at rapid traverse
1850 Grid shift for individual axis
1851 Backlash compensation for individual axis
1881 Permissible error amount for starting chopping compensation
1896 Mark 1 intervals on linear scale having reference marks
1912 Zero-width synchronization error for each axis
1913 Maximum permissible synchronization error for each axis at rapid traverse
1914 Maximum permissible synchronization error for each axis at stop
1917 Zero-width synchronization error for each axis No.2
1971 Dual position feedback function : conversion coefficient (numerator)
1972 Dual position feedback function : conversion coefficient (denominator)
1975 Second stage start/end parameter (when the two-stage backlash acceleration function is used)
1994 Overshoot compensation enable level
1996 Unexpected disturbance torque detection pull-back amount
2676 Detection unit parameter
2786 Lifting function against gravity at emergency stop : distance to lift
2795 Torsion preview control: maximum compensation value (LSTCM)
2799 Torsion preview control: acceleration torsion compensation value K1 (LSTK1)
2804 Torsion preview control: acceleration torsion compensation value K1N (LSTK1N)
2817 Synchronous axes automatic compensation function : maximum compensation value
5227 Distance from origin to reference position on linear scale having reference marks
5423 Pitch error compensation magnification
Pitch error compensation (absolute value) at reference position for movement to reference position in
5428
direction opposite to origin return direction
5433 Second cyclic pitch error compensation magnification
5449 Three-dimensional error compensation magnification
- 545 -
No. Description
5471 Compensation α at compensation point number a for individual axis
5472 Compensation β at compensation point number b for individual axis
5473 Compensation γ at compensation point number c for individual axis
5474 Compensation ε at compensation point number d for individual axis
5504 Compensation point number d for movement axis 1 subjected to straightness compensation
5551 Compensation at compensation point number a for movement axis 1
5552 Compensation at compensation point number b for movement axis 1
5553 Compensation at compensation point number c for movement axis 1
5554 Compensation at compensation point number d for movement axis 1
5591 Compensation magnification 1 for movement axis 1 subjected to straightness compensation
- 546 -
B.2 PARAMETERS FOR Series 16i, 18i, 21i, AND 0i
No. Description
1821 Reference counter capacity for individual axis
1827 Effective area (in-position check) for individual axis at cutting feed
1850 Grid shift/reference position shift for individual axis
1876 Inductosyn 1-pitch interval
1877 Inductosyn shift
1885 Permissible cumulative movement value during torque control (PMC axis control)
1886 Position error with torque control canceled (PMC axis control)
2103 Unexpected disturbance torque detection amount retrace distance
2119 Function for changing the proportional gain in the stop state : stop judgement level
2173 Lifting function against gravity at emergency stop : distance to lift (When SWDBSx=1)
2373 Lifting function against gravity at emergency stop : distance to lift（When SWDBSx=０）
3623 Pitch error compensation magnification for individual axis
5300 Rigid tapping effective area (in-position check) for tapping axis
5302 Second-spindle rigid tapping effective area (in-position check) for tapping axis
5304 Third-spindle rigid tapping effective area (in-position check) for tapping axis
5310 Rigid tapping position error limit for tapping axis during movement
5312 Rigid tapping position error limit for tapping axis at stop
5314 Rigid tapping position error limit for tapping axis during movement
5350 Second-spindle rigid tapping position error limit for tapping axis during movement
5352 Second-spindle rigid tapping position error limit for tapping axis at stop
- 547 -
No. Description
5354 Third-spindle rigid tapping position error limit for tapping axis during movement
5356 Third-spindle rigid tapping position error limit for tapping axis at stop
5761 Compensation at compensation point number a for movement axis 1 (straightness compensation)
5762 Compensation at compensation point number b for movement axis 1 (straightness compensation)
5763 Compensation at compensation point number c for movement axis 1 (straightness compensation)
5764 Compensation at compensation point number d for movement axis 1 (straightness compensation)
5871 Compensation α at compensation point number a for individual axis (gradient compensation)
5872 Compensation β at compensation point number b for individual axis (gradient compensation)
5873 Compensation γ at compensation point number c for individual axis (gradient compensation)
5874 Compensation ε at compensation point number d for individual axis (gradient compensation)
Limit to difference in position error between master and slave axes (pair under simplified synchronization
8313
control)
8315 Maximum compensation for synchronization (pair under simplified synchronization control)
8316 Difference in reference counter between master and slave axes (pair under simplified synchronization control)
Limit to difference in position error between master and slave axes (more than one pair under simplified
8323
synchronization control)
8325 Maximum compensation for synchronization (more than one pair under simplified synchronization control)
Difference in reference counter between master and slave axes (more than one pair under simplified
8326
• Setting data for shifting external machine coordinate systems
- 548 -
B.3 PARAMETERS FOR Power Mate i
No. Description
1836 Servo error amount within which reference position return is assumed to be possible (when ISC is in use)
1872* Servo position error check value
2119 Function for changing the proportional gain in the stop state : stop judgement level
2173 Lift amount in lifting function against gravity at emergency stop (When SWDBSx=1)
2373 Lift amount in lifting function against gravity at emergency stop (When SWDBSx=0)
3623 Pitch error compensation magnification for individual axis (H is optional)
5300(D) Rigid tapping effective area (in-position check) for tapping axis
5310(D) Rigid tapping position error limit for tapping axis during movement
5312(D) Rigid tapping position error limit for tapping axis at stop
5314(D) Rigid tapping position error limit for tapping axis during movement
Limit to difference in position error between master and slave axes (pair under simplified synchronization
8313
control)
8315 Maximum compensation for synchronization (pair under simplified synchronization control)
- 549 -
No. Description
8316 Difference in reference counter between master and slave axes (pair under simplified synchronization control)
Limit to difference in position error between master and slave axes (more than one pair under simplified
8323(H)
control)
8325(H) Maximum compensation for synchronization (more than one pair under simplified synchronization control)
Difference in reference counter between master and slave axes (more than one pair under simplified
8326(H)
The parameter No. indicated with an asterisk (*) is related to a

function unique to the Power Mate.
The parameter No. suffixed with "(D)" are related to the functions
dedicated to the Power Mate i-D.
The parameter No. suffixed with "(H)" are related to the functions
dedicated to the Power Mate i-H.
- 550 -
B.4 PARAMETERS FOR Series 30i, 31i, AND 32i
No. Description
Distance from the point at which deceleration dog is turned off to first grid point when reference position shift
1844
of the reference position shift function is set to 0
1876 Inductosyn 1-pitch interval
1877 Inductosyn shift
2119 Function for changing the proportional gain in the stop state : stop judgment level
2173 Lift amount in lifting function against gravity at emergency stop (Bit 7 of No. 2298=0 when SWDBSx=1)
2373 Lift amount in lifting function against gravity at emergency stop (Bit 7 of No. 2298=0 when SWDBSx=0)
2386 Torsion preview control: Acceleration torsion compensation value K1 (LSTK1)
2391 Torsion preview control: Acceleration torsion compensation value K1N (LSTK1N)
2404 Synchronous axes automatic compensation : Maximum compensation
3623 Pitch error compensation magnification for individual axis
Pitch error compensation value at reference position when movement to reference position is made in the
3627
direction opposite to reference position return direction
5300 First-spindle rigid tapping effective area (in-position check) for tapping axis
5302 Second-spindle rigid tapping effective area (in-position check) for tapping axis
5304 Third-spindle rigid tapping effective area (in-position check) for tapping axis
5306 Fourth-spindle rigid tapping effective area (in-position check) for tapping axis
- 551 -
No. Description
5310 First-spindle rigid tapping position error limit for tapping axis during movement
5312 First-spindle rigid tapping position error limit for tapping axis at stop
5350 Second-spindle rigid tapping position error limit for tapping axis during movement
5352 Second-spindle rigid tapping position error limit for tapping axis at stop
5354 Third-spindle rigid tapping position error limit for tapping axis during movement
5356 Third-spindle rigid tapping position error limit for tapping axis at stop
5358 Fourth-spindle rigid tapping position error limit for tapping axis during movement
5360 Fourth-spindle rigid tapping position error limit for tapping axis at stop
5871 Compensation α at compensation point number a for individual axis (gradient compensation)
5872 Compensation β at compensation point number b for individual axis (gradient compensation)
5873 Compensation γ at compensation point number c for individual axis (gradient compensation)
5874 Compensation ε at compensation point number d for individual axis (gradient compensation)
6287 Position error limit at torque limit skip
7772 Number of pulses from position detector per rotation of EGB master axis (tool axis) [path type]
7773 Number of pulses from position detector per rotation of EGB slave axis (workpiece axis) [path type]
7782 Number of pulses from position detector per rotation of EGB master axis [axis type]
7783 Number of pulses from position detector per rotation of EGB slave axis [axis type]
8181 Synchronous error limit for each axis (axis recomposition)
8323 Limit of position error check in feed axis synchronous control
8326 Difference in reference counter value between master axis and slave axis
8331 Maximum permissible synchronous error in synchronous error excess alarm 1
8332 Maximum permissible synchronous error in synchronous error excess alarm 2
8333 Synchronous error zero width for each axis
8335 Synchronous error zero width 2 for each axis
8377 Permissible error at start of chopping compensation
Maximum permissible movement amount at reference position setup of linear scale with absolute addressing
14010
reference marks
14988 Magnification of cycle type second pitch error compensation for each axis
• Setting data for shifting external machine coordinate systems
- 552 -
C.FUNCTION-SPECIFIC SERVO
B-65270EN/07 APPENDIX PARAMETERS
C FUNCTION-SPECIFIC SERVO
PARAMETERS
: Parameters set up automatically or cleared at initialization
Parenthesized parameters : Common parameters that are also used for other functions
Parameter number
Meaning
FS15i FS30i,16i,etc.
[Servo initialization functions]
1804 2000 Initialization bits
1874 2020 Motor ID number
1806 2001 AMR
1820 1820 CMR
1977 2084 Flexible feed gear (numerator)
1978 2085 Flexible feed gear (denominator)
1879 2022 Move direction
1876 2023 Number of velocity pulses → 2.1.2
1891 2024 Number of position pulses
2628 2185 Position pulses conversion coefficient
1804#0 2000#0 1: Multiplies the number of velocity pulses and position pulses by 10.
1896 1821 Reference counter capacity
2622 2179 Reference counter capacity (denominator)
1875 2021 Load inertia ratio
− 3111#0 1: Displays the servo setting screen.
[HRV control]
1707#0 2013#0 1: Servo HRV3 control
− 2014#0 1: Servo HRV4 control
− 2300#0 1: Extended HRV function → 4.2
2747 2334 High-speed HRV current control mode: Current loop gain magnification
2748 2335 High-speed HRV current control mode: Velocity loop gain magnification
[Vibration suppression functions in the stop state]
1959#7 2017#7 Velocity loop high cycle management function → 4.4.1
1894 2066 250 µs acceleration feedback gain → 4.4.2
1958#3 2016#3 Variable proportional gain function in the stop state
Variable proportional gain function in the stop state : stop judgement
1730 2119
level
→ 4.4.3
1747#3 2207#3 1: The velocity loop proportional gain in the stop state is 50%.
Function for changing the proportional gain in the stop state : arbitrary
2737 2324
magnification
1808#4 2003#4 N pulse suppression function
→ 4.4.4
1992 2099 N pulse suppression level
1743#2 2203#2 1: Enables the current loop 1/2 PI control function.
1742#1 2202#1 1: Enables the current loop 1/2 PI control function for cutting only.
(Shared by the cutting/rapid velocity loop gain switching function) →4.4.5
1742#2 2202#2 1: Always enables the current loop 1/2 PI control function when the bit →4.3
above is used.
2736 2323 Current control PI rate
1895 2067 TCMD filter coefficient → 4.3
1779 2156 Torque command filter coefficient for rapid traverse → 4.5.2
- 553 -
C. FUNCTION-SPECIFIC SERVO
PARAMETERS APPENDIX B-65270EN/07

Parameter number
Meaning
[Machine-resonance suppression functions]
[Resonance elimination filter]
2620 2177 Resonance elimination filter 1 : attenuation bandwidth
→ 4.5.3
(2779) (2366) Resonance elimination filter 4 : attenuation center frequency
(2780) (2367) Resonance elimination filter 4 : attenuation bandwidth
(2781) (2368) Resonance elimination filter 4 : damping
[Disturbance elimination filter]
2611#0 2223#0 1: disturbance elimination filter function
2731 2318 Disturbance elimination filter : gain
2732 2319 Disturbance elimination filter : inertia ratio
→ 4.5.4
2733 2320 Disturbance elimination filter : gain for inverse model
2734 2321 Disturbance elimination filter : filter time constant
2735 2322 Disturbance elimination filter : acceleration feedback limit
[Resonance elimination filter L]
2609#1 2221#1 1: Uses resonance elimination filter L.
2609#2 2221#2 1: Resonance elimination filter L is applied to VCMD/0: Resonance
elimination filter L is applied to feedback part only.
(2779) (2366) Resonance elimination filter L : attenuation center frequency → 4.5.5
(2780) (2367) Resonance elimination filter L : attenuation bandwidth
(2781) (2368) Resonance elimination filter L : damping
(2769) (2356) Resonance elimination filter L : Filter exclusion rate
[Observer]
1808#2 2003#2 Observer function
1859 2047 Observer coefficient (POA1)
1862 2050 Observer coefficient (POK1)
1863 2051 Observer coefficient (POK2) → 4.5.6
1960#1 2018#1 Disable function for observer in the stop state
Disable function for observer in the stop state : judgment level for
1730 2119
stop state
[Vibration damping control]
1718 2033 Position feedback pulse count (vibration damping control)
→ 4.5.7
1719 2034 Vibration damping control gain
[Machining point control]
2701#7 2288#7 1: Machining point control is enabled.
2768 2355 Machining point control: Center frequency of band-pass filter
2096 1989 Machining point control: Timing adjustment parameter → 4.5.10
2679 2266 Machining point control: gain 1
2678 2265 Machining point control: gain 2
- 554 -

Parameter number
Meaning
[Dual position feedback]
1709#7 2019#7 Dual position feedback function (optional function)
1861 2049 Dual position feedback function : maximum amplitude
1971 2078 Dual position feedback function : conversion coefficient (numerator)
1972 2079 Dual position feedback function : conversion coefficient (denominator)
1973 2080 Dual position feedback function : primary delay time constant
1974 2081 Dual position feedback function : zero zone
Dual position feedback function : alarm detection level of Semi-Full
1729 2118 → 4.5.8
error (Only this function can be used even if there is no option.)
1954#5 2010#5 1: The backlash compensation amount is added to the error counter
on the full-closed side.
1954#4 2010#4 1: The pitch error compensation amount is added to the error counter
on the semi-closed side.
1: The backlash compensation amount and pitch amount are added to
1746#4 2206#4
the error counters on both the full- and semi-closed sides.
1742#4 2202#4 1: Improvement of judge on zero width
[Feed-forward functions]
1956#1 2012#1 Machine speed feedback function
→ 4.5.9
1981 2088 Machine speed feedback gain
[Contour error suppression functions]
[Feed-forward functions]
1808#3 2003#3 PI control
1883#1 2005#1 Feed-forward function
→ 4.6.1 to 4.6.3
1961 2068 Feed-forward coefficient
1962 2069 Velocity feed-forward coefficient
1985 2092 Advanced preview feed-forward coefficient → 4.6.2
1959#5 2017#5 1: The response of feed-forward is improved when RISC is used.
1: The response of the position command is improved when RISC is → 4.6.3
1740#5 2200#5
used.
→ 4.3
1800#3 1800#3 Enables feed-forward in rapid traverse.
→ 4.8.3
1988 2095 Feed-forward timing adjustment coefficient
Feed-forward timing adjustment coefficient (for use when FAD is → 4.6.5
2808 2395
enabled)
Switches the feed-forward coefficient between cutting and rapid
traverse.
(1742#0) (2202#0)
(This parameter is also used for the cutting/rapid traverse-specific fine
acc./dec. function.)
Switches the feed-forward coefficient between cutting and rapid → 4.3
2602#3 2214#4 traverse. → 4.6.4
(This function is independent of fine acc./dec..) → 4.8.3
1767 2144 Position feed-forward coefficient for cutting
1768 2145 Velocity feed-forward coefficient for cutting
(1985) (2092) Position feed-forward coefficient for rapid traverse
(1962) (2069) Velocity feed-forward coefficient for rapid traverse
- 555 -

Parameter number
Meaning
[Backlash acceleration functions]
1808#5 2003#5 Backlash acceleration function
1860 2048 Backlash acceleration amount
1964 2071 Period during which backlash acceleration remains effective
(1725) (2114) Acceleration amount override
(2751) (2338) Limit of acceleration amount
(1987) (2094) Backlash acceleration amount (for reverse from negative to positive
direction)
→ 4.6.6
(2753) (2340) Acceleration amount override (for reverse from negative to positive
direction)
(2754) (2341) Limit of acceleration amount (for reverse from negative to positive
direction)
1953#7 2009#7 Backlash acceleration stop
1975 2082 Timing at which the backlash acceleration is stopped
1953#6 2009#6 1: Enables the backlash acceleration function during cutting feed only.
1851 1851 Backlash compensation
→ 4.6.6 to 4.6.7
1884#0 2006#0 1: Does not reflect the backlash compensation in positions.
1957#6 2015#6 Two-stage backlash acceleration function
(1808#5) (2003#5) (The backlash acceleration function is also enabled.)
(1860) (2048) First stage acceleration amount
First stage acceleration amount from negative direction to positive
1987 2094
direction
1760 2137 First stage acceleration override
1975 2082 Second stage start position
1982 2089 Second stage end scale factor
1724 2039 Second stage acceleration amount → 4.6.7
1790 2167 Second stage offset
1725 2114 Second stage acceleration override
2751 2338 Second stage acceleration amount limit value
Second stage acceleration amount (for turn-over from negative
2752 2339
direction to positive direction)
Second stage acceleration amount override (for turn-over from
2753 2340
negative direction to positive direction)
Second stage acceleration amount limit value (for turn-over from
2754 2341
negative direction to positive direction)
1960#2 2018#2 The format of the second stage acceleration override is changed.
1953#6 2009#6 1: Enables backlash acceleration only during cutting feed.
→ 4.6.7
1: When bit 3 of parameter No. 1800 = 1, the backlash acceleration
2611#7 2223#7
function is enabled only for cutting feed.
(1980) (2087) Torque offset
(2603#1) (2215#1) Torque offset canceling when an emergency stop is released
- 556 -

Parameter number
Meaning
[Static friction compensation]
1883#7 2005#7 Static friction compensation function
(1808#5) (2003#5) (The backlash acceleration function is also enabled.)
(1964) (2071) Compensation count
1965 2072 Static friction compensation → 4.6.8
1966 2073 Stop state judgement parameter
(1953#7) (2009#7) Stop of static friction compensation
1990 2097 Parameter for stopping static friction compensation
[Torsion preview control]
Torsion preview control: maximum compensation value (LSTCM)
2795 2382 (Setting maximum compensation value enables torsion preview
control.)
Torsion preview control: acceleration torsion compensation value K1
2799 2386
(LSTK1)
2800 2387
(LSTK2)
2801 2388
(LSTK3) → 4.6.9
2802 2389 Torsion preview control: torsion delay compensation value KD (LSTKD)
Torsion preview control: torsion delay compensation value KDN
2803 2390
(LSTKDN)
Torsion preview control: acceleration torsion compensation value K1N
2804 2391
(LSTK1N)
2805 2392
(LSTK2N)
2806 2393
(LSTK3N)
Torsion preview control: torsion torque compensation coefficient
2815 2402
(LSTKT)
[Overshoot compensation functions]
1808#6 2003#6 Overshoot compensation function
1857 2045 Velocity loop incomplete integral gain (PK3V)
1970 2077 Overshoot compensation counter → 4.7
1994 2101 Overshoot compensation enable level
1742#3 2202#3 Overshoot compensation type 2
[High-speed positioning functions]
1957#0 2015#0 Position gain switch function
1714 2029 Limit speed for enabling position gain switching
1: Increases the increment system for the effective switch velocity to
1744#1 2204#1 → 4.8.1
10 times.
1957#0 2015#0
Position gain switch function type 2
1744#5 2204#5
- 557 -

Parameter number
Meaning
1957#1 2015#1 Low-speed integration function
1714 2029 Limit speed for disabling low-speed integration at acceleration
→ 4.8.2
1716 2030 Limit speed for enabling low-speed integration at deceleration
(1744#1) (2204#1) 1: Increases the increment system for the switch velocity to 10 times.
1951#6 2007#6 Fine acc./dec. (FAD) function
1749#2 2209#2 0: FAD bell-shaped, 1: FAD linear type
→ 4.8.3
Position feed-forward coefficient
(1985) (2092)
(This parameter is also used for look-ahead control.)
1742#0 2202#0 Cutting/rapid traverse-specific fine acc./dec. function
1800#3 1800#3 Enables feed-forward in rapid traverse.
1702 2109 Fine acc./dec. time constant
1766 2143 Fine acc./dec. time constant 2 → 4.3
(1767) (2144) Position feed-forward coefficient for cutting → 4.8.3
(1768) (2145) Velocity feed-forward coefficient for cutting
(1985) (2092) Position feed-forward coefficient for rapid traverse
(1962) (2069) Velocity feed-forward coefficient for rapid traverse
1: Synchronization is established in the rigid tapping mode when FAD
1749#3 2209#3 → 4.8.3
is specified.
[Serial feedback dummy functions]
1953#0 2009#0 Dummy serial feedback function
1800#1 1800#1 1: Ignores the V-READY ON alarm.
1745#2 2205#2 Separate detector-based dummy feedback function → 4.9
2692#0 2279#0 The ready signal is output to the amplifier when the dummy function is
enabled.
[Brake control functions]
1883#6 2005#6 Brake control function
1976 2083 Brake control timer
→ 4.10
2686#7 2273#7 Torque limit setting function during brake control
2788 2375 Torque limit magnification during brake control
[Stop distance reduction functions]
1959#0 2017#0 Emergency stop distance reduction function type 1 (VCMD0) → 4.11.1
1744#7 2204#7 Emergency stop distance reduction function type 2 (return) → 4.11.2
2786 2373 Lifting function against gravity at emergency stop : distance to lift
2787 2374 Lifting function against gravity at emergency stop : lifting time
- 2173 Lifting function against gravity at emergency stop : distance to lift → 4.11.3
(When SWDBSx=1)
- 2298#7 1: The parameter for specifying a distance to lift is set in µm.
Separate detector hardware disconnection stop distance reduction
1745#4 2205#4
function → 4.11.4
1745#5 2205#5 For axes under synchronization control, this bit is also set.
2695#5 2282#5 Quick stop function for separate serial detector alarms → 4.11.5
2600#7 2212#7 OVL and OVC alarm stop distance reduction function → 4.11.6
- 558 -

Parameter number
Meaning
[Unexpected disturbance torque detection functions] (Optional functions)
1958#0 2016#0 Unexpected disturbance torque detection function
1740#5 2200#5 Improvement in the accuracy of an estimated disturbance load
Improvement in the accuracy of an estimated disturbance load (A
2716 2302
Q-phase current phase lag is compensated for.)
1980 2087 Torque offset
→ 4.12.1
1727 2116 Dynamic friction compensation value
2758 2345 Dynamic friction compensation value in the stop state
2759 2346 Dynamic friction compensation limit value
1997 2104 Unexpected disturbance torque detection alarm level
1996 2103 Retrace distance
Cutting/traverse unexpected disturbance torque detection switching
1740#3 2200#3
function
Cutting/traverse unexpected disturbance torque detection switching
2603#7 2215#7
function type-2
(1997) (2104) Unexpected disturbance torque detection alarm level for cutting → 4.12.2
1765 2142 Unexpected disturbance torque detection alarm level for rapid traverse
2-axes simultaneous retract function at unexpected disturbance torque
2684#2 2271#2
detection
2603#1 2215#1 Torque offset canceling when an emergency stop is released
2342 2755 Unexpected disturbance torque detection: Acceleration threshold
2343 2756 Unexpected disturbance torque detection: Alarm level for high
→ 4.12.3
acceleration
2771 2358 Unexpected disturbance torque detection: Post-acceleration timer
[Linear motor functions]
1954#2 2010#2 Linear motor control function
1705 2112 AMR conversion coefficient 1
1762 2139 AMR offset
→ 4.14.1
2683#0 2270#0 AMR offset setting range expansion from -60 degrees to +60 degrees
(2628) (2185) Position pulse conversion coefficient
1740#6 2200#6 The velocity loop proportional gain format is changed.
1750#2 2210#2 Current gain internally 4 times function
Overheat signal connection destination setting
2713#7 2713#3 OH connection destination
2713#7 2300#7 1 0 Connected to DI signal of PMC → 4.14.2
2713#3 2300#3 Connected to linear motor detection
1 1
circuit or temperature detection circuit
1753 2130 Smoothing compensation performed twice per pole pair

1754 2131 Smoothing compensation performed four times per pole pair
2782 2369 Smoothing compensation performed twice per pole pair (negative
direction)
→ 4.14.3
2783 2370 Smoothing compensation performed four times per pole pair (negative
direction)
2784 2371 Smoothing compensation performed six times per pole pair (negative
direction)
1743#6 2203#6 Linear motor quadruple smoothing compensation
- 559 -

Parameter number
Meaning
[Synchronous built-in servo motor functions]
1954#2 2300#2 Synchronous built-in servo motor control
1806 2001 AMR
2608#0 2220#0 Non-binary detector
1762 2139 AMR offset
2601#7 2213#7 Pole position detection function (optional)
2616#3 2228#3 Motor saliency 0: Lq>Ld, 1: Lq<Ld
2617#0 2229#0 1: AMR offset is used.
2617#3 2229#3 0: After pole detection, an abnormal movement is monitored.
2617#4 2229#4 0: Automatic selection mode (minute operation mode + stop mode) → 4.15
2625 2182 Current A for pole detection
2641 2198 Current B for pole detection
2642 2199 Current C for pole detection
2681 2268 Allowable travel distance magnification/stop speed decision value
2790 2377 Smoothing compensation performed 1.5 times per pole pair
2791 2378 Smoothing compensation performed 1.5 times per pole pair (negative
direction)
2793 2380 Smoothing compensation performed three times per pole pair
2794 2381 Smoothing compensation performed three times per pole pair (negative
direction)
Overheat signal connection destination setting
2713#7 2713#3 OH connection destination
2713#7 2300#7 1 0 Connected to DI signal of PMC → 4.14.2
2713#3 2300#3 Connected to αiCZ or
1 1
temperature detection circuit
[Torque control functions]

－ 2292#7 Moving axis setting
－ 2292#6 Calculation of interactive force from the first moving axis
－ 2292#5 Servo axis number for the first moving axis
2292#4
2292#3
－ 2292#2 Compensation for interactive force from the first moving axis
－ 2292#1 Compensation type for the first moving axis
2292#0
－ 2293#6 Calculation of interactive force from the second moving axis
－ 2293#5 Servo axis number for the second moving axis → 4.17
2293#4
2293#3
－ 2293#2 Compensation for interactive force from the second moving axis
－ 2293#1 Compensation type for the second moving axis
2293#0
－ 2478 Compensation gain for the first moving axis
－ 2479 Angle data offset for the first moving axis
－ 2480 Compensation gain for the second moving axis
－ 2481 Angle data offset for the second moving axis
- 560 -

Parameter number
Meaning
－ (2455) Integer part of the number of pulses per revolution
→ 4.17
－ (2456) Exponent part of the number of pulses per revolution
[Torque control functions]
1951#7 2007#7 Torque control type 1
1743#4 2203#4 Torque control type 2 → 4.18
1998 2105 Torque constant
- 2301#7 Torque command unit increase by a factor of 10
[Tandem disturbance elimination control] (Optional functions)
1709#1 2019#1 Enables tandem disturbance elimination control.
Enables the velocity feedback average function. (Set this parameter for
1952#2 2008#2
the main axis only.)
Tandem disturbance elimination control proportional gain (Set this
1721 2036
parameter for the main axis only.)
Tandem disturbance elimination control phase compensation
1721 2036
coefficient (Set this parameter for the sub-axis only.) → 4.19
Tandem disturbance elimination control integral gain (Set this
2738 2325
parameter for the main axis only.)
Tandem disturbance elimination control phase compensation
2738 2325
coefficient (Set this parameter for the sub-axis only.)
Tandem disturbance elimination control incomplete integral time
2746 2333
constant (Set this parameter for the main axis only.)
[Synchronous axes automatic compensation function]
Enables synchronous axes automatic compensation. (Set this
2688#3 2275#3
parameter for the sub-axis.)
2816 2403 Synchronous axes automatic compensation: coefficient (K) (sub-axis)
→ 4.20
Synchronous axes automatic compensation:
2817 2404
maximum compensation value (sub-axis), dead-band width (main-axis)
2818 2405 Synchronous axes automatic compensation : filter coefficient (sub-axis)
[Tandem control functions] (Optional functions)
1817#6 1817#6 Tandem control function (main- and sub-axes)
− 1010 Number of CNC controlled axes → 4.21
1021 − Parallel-axis name (main axis: 77, sub-axis: 83)
1980 2087 Preload value → 4.21.1
1952#7 2008#7 Damping compensation function
Damping compensation gain (main axis) and damping compensation → 4.21.2
1721 2036
phase (sub-axis)
1952#2 2008#2 Velocity feedback average function → 4.21.3
1951#1 2007#1 Servo alarm two-axis monitor function → 4.21.4
1960#7 2018#7 Motor feedback sharing function (sub-axis) → 4.21.5
1940#1 2200#1 Full-closed loop feedback sharing function (sub-axis) → 4.21.6
2686#1 2273#1 Integrator copy (sub-axis) → 4.21.9
- 2007#4 Tandem speed difference alarm (sub-axis)
→ 4.21.10
- 2357 Tandem speed difference alarm (sub-axis)
- 561 -

Parameter number
Meaning
[Servo check board functions]
1956#5 2012#5 VCMD output magnification
→ Appendix I
1956#4 2012#4 00: 1, 01: 16, 10: 162, 11: 163
1: Outputs an estimated load to the check board.
1957#5 2015#5 → 4.6.7, 4.12
(The estimated load is output to the torque command channel.)
1: Enables the four-times torque command output. → 4.14,
1743#5 2203#5
(Small-torque command output can be measured.) Appendix I
For internal data output: Must be kept at 0.
→ 4.14,
1726 2115 The output of the SPEED signal (number of revolutions) is disabled.
Appendix I
(Series 9096)
1774 2151 Internal data output: Always specify 0. (Other than Series 9096)
1775 2152 Internal data output: Always specify 0. (Other than Series 9096) → 4.14
1776 2153 Internal data output: Always specify 0. (Other than Series 9096)
1: Performs high-speed data output to the check board (Other than
1746#7 2206#7 → Appendix I
Series 9096).
2613#1 2225#1 1: TCMD signal check board output 1/2 (Other than Series 9096)
1: SPEED signal check board output 1/2 (7500 min-1/5 V) (Other than → Appendix I
2613#2 2225#2
Series 9096)
2208#3 - 1: Arbitrary data screen is displayed.
DGN353 DGN for internal data display → 4.14
-
DGN354 DGN for internal data display
- 2278#2 The first or third servo check interface unit is used.
- 2278#3 The second or fourth servo check interface unit is used. → Appendix J
- 2315 Servo check interface unit output signal setting
[Related to simplified frequency characteristics measurement]
2683#7 2270#7 1: Starts disturbance input.
1: Inputs disturbance for both of an odd-numbered axis and
2683#6 2270#6 even-numbered axis simultaneously. (Used for synchronous axes or
tandem axes)
1: The input waveform of disturbance input is a square wave.
2683#5 2270#5 → Appendix H
(Usually, select 0: Sine wave.)
2739 2326 Disturbance input gain
2740 2327 Disturbance input start frequency
2741 2328 Disturbance input end frequency
2742 2329 Number of disturbance input measurement points
- 562 -
D.PARAMETERS RELATED TO
HIGH-SPEED AND HIGH
B-65270EN/07 APPENDIX PRECISION OPERATIONS
D PARAMETERS RELATED TO
HIGH-SPEED AND HIGH PRECISION
OPERATIONS
The i series CNCs are provided with some functions for high-speed
and high precision operations. This appendix lists parameters
categorized by model and function and their standard setting values so
as to make it easy to tune the functions.
Appendix D consists of the following two items:
(1) CNC model-specific information
This section lists high-speed and high precision functions and
parameters related to them for individual CNC models.
The parameter tables in this section contain standard setting
values.
(2) Servo parameters
This section lists servo parameters common to all CNC models
and standard setting values for them.
NOTE
1 Use the standard setting values included in the parameter tables as
reference data for initialization.
If a parameter needs tuning based on the machine type, determine
a final setting for the parameter according to the characteristic of
the machine and how to use it.
To reduce machining time, change parameters from standard
settings to speed priority I to speed priority II while checking the
operation status. (The settings for speed priority II can reduce
much more machining time than the settings for speed priority I.)
2 For the specifications of CNC models and detailed explanations
about their functions, refer to the respective CNC manuals.
3 In the following table, the circle indicates that the item is supported,
the triangle indicates partial support, and the cross indicates
non-support.
Appendix D, "PARAMETERS SET WITH VALUES IN

DETECTION UNITS", consists of the following sections:
D.1 MODEL-SPECIFIC INFORMATION .....................................563

D.1.1 Series 15i-MB ..............................................................564
D.1.2 Series 16i/18i/21i/0i/0i Mate-MB, 0i/0i Mate-MC/
20i-FB ..........................................................................567
D.1.3 Series 30i/31i/32i-A, 31i-A5 ........................................577
D.2 SERVO PARAMETERS RELATED TO HIGH-SPEED
AND HIGH PRECISION OPERATIONS................................580
- 563 -
D. PARAMETERS RELATED TO
HIGH-SPEED AND HIGH
PRECISION OPERATIONS APPENDIX B-65270EN/07
D.1 MODEL-SPECIFIC INFORMATION
D.1.1 Series 15i-MB
[Functions related to high-speed and high precision operations]

Look-ahead acc./dec.
High-speed high precision functions Fine HPCC
before interpolation
Series 15i-MB
Acc./dec. before interpolation
Linear/Bell-shaped/
Type Linear/Bell-shaped
Smooth bell-shaped
Time constant setting for individual axes
Velocity control
Automatic corner deceleration
Arc radius-based velocity control
Acceleration-based velocity control
Cutting load-based velocity control
Jerk control
Optimum torque acc./dec.
Other functions
Nano interpolation
5-axis machining function
Smooth interpolation
NURBS
Nano smoothing
Additional hardware None None
[Parameters]
Use the standard setting values included in the parameter tables as
reference data for initialization. If a parameter needs tuning based on
the machine type, determine a final setting for the parameter according
to the characteristic of the machine and how to use it.
• Standard settings (precision priority)
When there is vibration or significant impact, or when machining
is to be performed more precisely, make settings based on the
standard settings.
• Cutting time-priority setting
To reduce machining time, make settings for speed priority I then
for speed priority II in stages. The settings for speed priority II
can reduce much more machining time than the settings for speed
priority I.
- 564 -
HIGH-SPEED AND HIGH
- Parameters that need tuning based on the machine type

Standard setting value
Parameter
Standard Speed Speed Description
No.
setting priority I priority II
Allowable speed difference (mm/min) in acceleration-dependent
1478 400.0 500.0 1000.0
on speed difference at corners
1635 24 16 16 Time constant (msec) for acc./dec. after interpolation
Time constant (msec) for bell-shaped acc./dec. before
1656 64 48 32
interpolation (portion with the time fixed)
Acceleration of linear-/bell-shaped acc./dec. before interpolation
1660 700.0 2000.0 4000.0 (portion with the acceleration fixed)
(Acceleration is specified in mm/sec2 units for individual axes.)
2
Allowable acceleration (mm/sec ) during acceleration-dependent
1663 525.0 1500.0 3000.0 deceleration (HPCC mode)
(Acceleration is specified in mm/sec2 for individual axes.)
2
Allowable acceleration (mm/sec ) at arc interpolation during
1665 525.0 1500.0 3000.0 acceleration-dependent deceleration (non-HPCC mode)
- Parameters that do not usually need tuning so often and can be left at fixed values
Parameter Standard
Description
No. setting value
1483 100.0 Lower speed limit to acceleration-dependent deceleration (HPCC mode) (mm/min)
Lower speed limit to deceleration acceleration-dependent (non-HPCC mode)
1491 100.0
(mm/min)
Speed difference- or acceleration-dependent deceleration type
0: Compatible with the 15B (by making the most of allowable speed difference and
1517#6 0 acceleration for each axis)
1: Fixed speed regardless of the direction of movement as long as the same contour
is involved.
0: Linear- or bell-shaped acc./dec. after interpolation enabled (Note 1)
1600#4 0
1: Exponential acc./dec. after interpolation enabled
When using the function for changing the time constant of bell-shaped acc./dec.
1603#6 1/0
before interpolation, set 1.
mm / inch Reference speed in the function for changing the time constant of bell-shaped
1473
10000.0/3937.0 acc./dec. before interpolation (mm/min / inch/min)
Setting this parameter to 1 enables look-ahead acc./dec. before interpolation and
multibuffer when the power is switched on and in the cleared state. Fine HPCC is
2401#6 0
also enabled if available.
If it is reset to 0, it is turned on with the G05.1Q1 command.
Setting this parameter to 1 causes a specified speed to be ignored and assumes that
7565#7 0
a speed set in parameter No. 7567 is specified
Specified clamp value in the fine HPCC mode (mm/min (input unit))
7567 0 If the parameter setting is 0, no clamp takes place except for the maximum cutting
speed specified in parameter No. 1422.
Set this parameter to 1 if the cutting load-based deceleration function is to be
7565#4 0/1
enabled. (This parameter is used if the mechanical rigidity of the Z-axis is low.)
7697#1 0/1 When using the slant type for override by cutting load, set 1. (Note 2)
Override of area 1 in deceleration by cutting load (This setting is unnecessary if bit 4
7698 80 of parameter No. 7565 is set to 0 or bit 1 of parameter No. 7697 is set to 0.) (%) (Note
2)
Region 2 override (%) for the cutting load-based deceleration function (needn't be
7591 80
specified if bit 4 of parameter No. 7565 = 0)
- 565 -
HIGH-SPEED AND HIGH
Parameter Standard
Description
No. setting value
7592 70
7593 60
8495#0 0/1 When using smooth velocity control as velocity control by acceleration, set 1. (Note 2)
NOTE
1 To perform bell-shaped acc./dec. after cutting feed
interpolation, the option for bell-shaped acc./dec.
after cutting feed interpolation is required.
2 Only fine HPCC can be used.
- 566 -
HIGH-SPEED AND HIGH
D.1.2 Series 16i/18i/21i/0i/0i Mate-MB, 0i/0i Mate-MC/20i-FB

AI nano
AI AI nano High AI high high
Advanced
advanced AI contour contour precision precision precision
High-speed and high precision preview
preview control control contour contour contour
function control
control (AICC) (AI nano control control control
(APC)
(AI-APC) CC) (HPCC) (AI-HPCC) (AI nano
HPCC)
Series 0i Mate M-C
Series 0i-MC
Series20i-FB
Series 0i Mate-MB
Series 0i-MB
Series21i-MB
Series18i-MB
Series16i-MB
Linear/ Linear/ Linear/ Linear/
Linear/ Bell-shaped/ Bell-shaped/ Linear/ Bell-shaped/ Bell-shaped/
Type Linear
Bell-shaped Smooth Smooth Bell-shaped Smooth Smooth
bell-shaped bell-shaped bell-shaped bell-shaped
Time constant setting for
individual axes
Velocity control
Automatic corner deceleration
Arc radius-based velocity control
Acceleration-based velocity
control
Cutting load-based velocity
control
Jerk control (Note 1)
Optimum torque acc./dec.
Other functions
Nano interpolation
5-axis machining function
Smooth interpolation
NURBS
Nano smoothing
Additional hardware None None None None RISC board is necessary.
NOTE
1 Jerk control can be used in the Series
16i-MB/18i-MB.
[Parameters]
Described below are the parameters that must be specified for
individual high-speed and high precision cutting machines separately.
- 567 -
HIGH-SPEED AND HIGH

standard settings.
priority I.
NOTE
1 Performing bell-shaped acc./dec. after interpolation
requires the look-ahead bell-shaped acc./dec. after
interpolation option.
2 Performing linear-shaped acc./dec. after cutting
feed interpolation requires the linear-shaped
acc./dec. after cutting feed interpolation option.
3 Performing bell-shaped acc./dec. after cutting feed
interpolation requires the bell-shaped acc./dec.
after cutting feed interpolation option.
4 Performing bell-shaped acc./dec. in rapid-traverse
requires the bell-shaped acc./dec. in rapid-traverse
option.
- 568 -
HIGH-SPEED AND HIGH
(1) Advanced preview control

Parameter
No.
1432 - - - Maximum cutting feedrate (mm/min) for individual axes
Time constant (msec) for linear-shaped acc./dec. in rapid-traverse
1620 - - -
for individual axes
Time constant T2 (msec) for bell-shaped acc./dec. in
1621 - - -
rapid-traverse for individual axes
1730 3060 5150 7275 Feedrate upper limit (mm/min) for arc radius R
1731 5000 5000 5000 Arc radius R (1 µm) for arc radius-based feedrate upper limit
1732 100 100 100 Arc radius-based feedrate clamp lower speed limit (mm/min)
1768 24 16 16 Time constant (msec) for acc./dec. after cutting feed interpolation
Maximum cutting feedrate (mm/min) during acc./dec. before
1770 10000 10000 10000
interpolation
Time (msec) allowed before a maximum cutting feedrate during
1771 240 80 40
acc./dec. before interpolation is reached
Allowable speed difference (mm/min) in acceleration-dependent on
1783 400 500 1000
speed difference at corners
Speed (mm/min) at occurrence of overtravel alarm
1784 - - -
To be specified according to the overrun distance at overtravel
Parameter Standard setting
Description
No. value
1602#0 1 The type of linear-shaped acc./dec. before interpolation is B.
1602#4 1 Automatic deceleration at corners is under speed difference-dependent control
#6,#3
1,0 Acc./dec. after interpolation is of a linear type (to be specified when FAD is used)
1602#6,#3
Acc./dec. after interpolation is of a bell-shaped type (to be specified when FAD is
1,1
not used)
To be set to 1 if the CMR setting is 2 or greater (parameter No. 1820 setting is 4
1802#7 0/1
or greater).
3403#0 1 To be set to the standard setting value.
- 569 -
HIGH-SPEED AND HIGH
(2) AI advanced preview control

Parameter
No.
Time constant (msec) for linear-shaped acc./dec. in
1620 - - -
1621 - - -
1770 10000 10000 10000
interpolation
1771 240 80 40
Time constant of bell-shaped acc./dec. before interpolation (for
1772 64 48 32
constant-time part) (msec)
1783 400 500 1000
1784 - - -
Parameter (msec) for determining an allowable acceleration in
determining acceleration-dependent speed. The parameter is to
be set with the time allowed before a maximum cutting feedrate
1785 320 112 56
(parameter No. 1432) is reached.
A maximum cutting feedrate of 10000 mm/min is used as the
standard setting value.
Description
No. value
#6,#3
1,0 Acc./dec. after interpolation is of a linear type (to be specified when FAD is used)
1602#6,#3
Acc./dec. after interpolation is of a bell-shaped type (to be specified when FAD is
1,1
not used)
Acc./dec. before interpolation is of bell-shaped type. (0: Linear-shaped acc./dec.
1603#7 1
before interpolation)
1802#7 0/1
or greater).
- 570 -
HIGH-SPEED AND HIGH
(3) AI contour control

Parameter
No.
1620 - - -
for individual axes
1621 - - -
1770 10000 10000 10000
interpolation
1771 240 80 40
Time constant (msec) for bell-shaped acc./dec. before interpolation
1772 64 48 32
(portion with the time fixed)
1783 400 500 1000
1784 - - -
determining acceleration-dependent speed. The parameter is to be
1785 320 112 56 set with the time allowed before a maximum cutting feedrate
(parameter No. 1432) is reached. A maximum cutting feedrate of
10000 mm/min is used as the standard setting value.
Parameter No. Standard setting value Description
#6,#3
Acc./dec. after interpolation is of a linear type (if bell-shaped acc./dec.
1602#6,#3 1,0
before interpolation is used)
Acc./dec. after interpolation is of a bell-shaped type (if linear-shaped
1,1
acc./dec. before interpolation is used)
Acc./dec. before interpolation is of a bell-shaped type (0: Linear-shaped
1603#7 1
acc./dec. before interpolation)
To be set to 1 if the CMR setting is 2 or greater (parameter No. 1820
1802#7 0/1
setting is 4 or greater).
7052#0 0/1 To be set to 1 for the PMC and Cs axes.
To be set to 1 if a function of changing the time constant for bell-shaped
7055#3 1/0
acc./dec. before interpolation is to be used.
7058 0 To be set to standard value.
mm / inch Reference speed (mm/min / inch/min) for a function of changing
7066
10000/3937 the time constant for bell-shaped acc./dec. before interpolation
- 571 -
HIGH-SPEED AND HIGH
(4) AI nano contour control

Parameter
No.
1620 - - -
for individual axes
1621 - - -
1770 10000 10000 10000
interpolation
1771 240 80 40
1772 64 48 32
1783 400 500 1000
1784 - - -
Description
No. value
#6,#3
Acc./dec. after interpolation is of a linear type (if bell-shaped acc./dec. before
1,0
1602#6,#3 interpolation is used)
Acc./dec. after interpolation is of a bell-shaped type (if linear-shaped acc./dec.
1,1
Acc./dec. before interpolation is of a bell-shaped type (0: Linear-shaped acc./dec.
1603#7 1
before interpolation)
1802#7 0/1
or greater).
7052#0 0/1 To be set to 1 for the PMC and Cs axes.
7053#0 0 AI nano contour control (1: AI contour control is enabled.)
7055#3 1/0
7058 0 To be set to standard value.
mm / inch Reference speed (mm/min / inch/min) for a function of changing the time
7066
10000/3937 constant for bell-shaped acc./dec. before interpolation
- 572 -
HIGH-SPEED AND HIGH
(5) High-precision contour control

Parameter
No.
Time constant (msec) for linear-shaped acc./dec. in
1620 - - -
1621 - - -
8400 10000 10000 10000
interpolation
8401 240 80 40
8410 400 500 1000
Time constant (msec) for bell-shaped acc./dec. before
8416 64 48 32
interpolation (portion with the time fixed)
determining acceleration-dependent speed. The parameter is to
be set with the time allowed before a maximum cutting feedrate
8470 320 112 56
(parameter No. 1432) is reached.
A maximum cutting feedrate of 10000 mm/min is used as the
standard setting value.
Description
No. value
#6,#3
1,0
1,1
1802#7 0/1
or greater).
Largest of controlled-axis numbers for which high precision contour control is
7510 -
performed
8402#7,#1, 1,1 Acc./dec. before interpolation is of a bell-shaped type (with the acceleration
1603#3 1 change fixed)
8403#7,#1, 1,1 No alarm is raised on an M, S, T, B, or rapid traverse command.
8404#1,#0 1,1 Rapid traverse is processed on the RISC side.
8420 180 Number of blocks to be looked ahead (0: 120 blocks)
Set this parameter to 1 if cutting load-dependent override is to be used.
8451#4 0/1
(This parameter is used if the mechanical rigidity of the Z-axis is low.)
Region 2 override (%) for the cutting load-based deceleration function
8456 80
(needn’t be specified if bit 4 of parameter No. 8451 = 0)
Region 3 override (%) for the cutting load-based deceleration function)
8457 70
- 573 -
HIGH-SPEED AND HIGH

Description
No. value
8458 60
8475#2 1 Automatic deceleration at corners is enabled.
Acceleration-dependent determination of speed during arc interpolation is
8475#3 1
enabled.
To be set to 1 if the software series on the RISC side is B435. Otherwise, to be
8480#4 0/1
reset to 0.
Scaling/coordinate system rotation in high precision contour control mode is
8485#0 1/0 enabled/disabled.
(An option is necessary.)
A canned cycle in high precision contour control mode is enabled/disabled.
8485#1 1/0
A helical interpolation in high precision contour control mode is
A involute interpolation in high precision contour control mode is
A smooth interpolation in high precision contour control mode is
- 574 -
HIGH-SPEED AND HIGH
(6) AI high precision contour control, AI nano high precision contour control

Parameter
No.
1620 - - -
for individual axes
1621 - - -
8400 10000 10000 10000
interpolation
Time (msec) allowed before a maximum cutting feedrate is
19510 240 80 40 reached for an individual axis during acc./dec. before interpolation.
If this parameter is 0, a setting in parameter No. 8401 is used.
8410 400 500 1000
8416 64 48 32
Description
No. value
#6,#3
1,0
1,1
1802#7 0/1
or greater).
Largest of controlled-axis numbers for which high precision contour control is
7510 -
performed
Acc./dec. before interpolation is of a bell-shaped type (with the acceleration
8402#7,#1 1,1
change fixed)
8403#1 1 No alarm is raised on an M, S, T, B, or rapid traverse command.
8451#4 0/1
(This parameter is used if the mechanical rigidity of the Z-axis is low.)
19516 80
8456 80
8457 70
8458 60
- 575 -
HIGH-SPEED AND HIGH

Description
No. value
19501#6 1/0
19504#0 1 Bell-shaped rapid traverse acc./dec. is used.
mm / inch Reference speed (mm/min / inch/min) for a function of changing the time
19520
10000/3937 constant for bell-shaped acc./dec. before interpolation
Scaling is performed on the CNC side or, as 5-axis control mode, on the RISC
19600#0 0/1
side. (An option is necessary.)
Programmable mirror image is performed on the CNC side or, as 5-axis control
19600#1 0/1
mode, on the RISC side. (An option is necessary.)
Rotary dynamic fixture offset is performed on the CNC side or, as 5-axis control
19600#2 0/1
mode, on the RISC side. (An option is necessary.)
Coordinate rotation is performed on the CNC side or, as 5-axis control mode, on
19600#3 0/1
the RISC side. (An option is necessary.)
Three-dimensional coordinate conversion is performed on the CNC side or, as
19600#4 0/1
5-axis control mode, on the RISC side. (An option is necessary.)
Cutter compensation C is performed on the CNC side or, as 5-axis control mode,
19600#5 0/1
on the RISC side. (An option is necessary.)
- 576 -
HIGH-SPEED AND HIGH
D.1.3 Series 30i/31i/32i-A, 31i-A5

AI contour control II
High-speed and high precision AI contour
AI contour control II (Note 1) +
function control I
High-speed processing (Note 2)
Series30i-A ○ ○ ○
Series31i-A/A5 ○ ○ ○
Series32i-A ○ ○ ×
Linear/ Linear/
Linear/
Type Bell-shaped/ Bell-shaped/
Bell-shaped
Smooth bell-shaped Smooth bell-shaped
Acceleration setting for each axis ○ ○ ○
Velocity control
Velocity control by speed
○ ○ ○
difference among axes
Velocity control by acceleration in
○ ○ ○
circular interpolation
Acceleration-based velocity
○ ○ ○
control
Cutting load-based velocity
× ○ ○
control
Jerk control × ○ ○
Optimum torque acc./dec. ○ ○ ○
Other functions
Nano interpolation ○ ○ ○
5-axis machining functions (Note 3) ○ ○ ○
Smooth interpolation (Note 4) ○ ○ ○
NURBS (Note 4) ○ ○ ○
Nano smoothing (Note 4) ○ ○ ○
NOTE
1 In FS30i systems controlling more than four paths
and more than 20 axes, this function cannot be
used.
2 In FS30i and FS31i systems controlling more than
two paths and more than 12 axes, this function
cannot be used.
3 These functions can be used with the FS30i-A and
FS31i-A5 only.
4 These functions cannot be used with the FS32i.
- 577 -
HIGH-SPEED AND HIGH
[Parameters]
Described below are the parameters that must be specified for
individual high-speed and high precision cutting machines separately.
standard settings.
priority I.
- 578 -
HIGH-SPEED AND HIGH
(1) AI contour control I, AI contour control II

Parameter
No.
1620 - - -
for individual axes
1621 - - -
Acceleration in acc./dec. before interpolation
1660 700.0 2000.0 4000.0 (for constant-acceleration part)
Time constant of bell-shaped acc./dec. before interpolation (msec)
1772 64 48 32
(for constant-acceleration part)
1783 400.0 500.0 1000.0
Permissible acceleration in deceleration by acceleration
1737 525.0 1500.0 3000.0
Permissible acceleration in deceleration by acceleration in circular
1735 525.0 1500.0 3000.0 interpolation
Parameter Standard
Description
No. setting value
#6,#3
1602#6,#3 1,0 Acc./dec. after interpolation is of a linear type
1,1 Acc./dec. after interpolation is of a bell-shaped type (Note 1)
To be set to 1 if a function of changing the time constant for bell-shaped acc./dec.
7055#3 1/0
before interpolation is to be used.
mm / inch Reference speed (mm/min / inch/min) for a function of changing the time constant for
7066
10000.0/3937.0 bell-shaped acc./dec. before interpolation
19503#0 0/1 When using smooth velocity control as velocity control by acceleration, set 1. (Note 2)
8451#4 0/1
(This parameter is used if the mechanical rigidity of the Z-axis is low.) (Note 2)
19515#1 0/1 When using the slant type for override by cutting load, set 1. (Note 2)
Region 1 override (%) for the cutting load-based deceleration function (needn’t be
19516 80
specified if bit 4 of parameter No. 8451 or bit 1 of parameter No. 19515 = 0) (Note 2)
8456 80
(needn’t be specified if bit 4 of parameter No. 8451 = 0) (Note 2)
8457 70
8458 60
NOTE
1 To perform bell-shaped acc./dec. after cutting feed interpolation, the option for
bell-shaped acc./dec. after cutting feed interpolation is required.
2 These functions cannot be used with AI contour control I.
- 579 -
HIGH-SPEED AND HIGH
D.2 SERVO PARAMETERS RELATED TO HIGH-SPEED AND

HIGH PRECISION OPERATIONS
Described below are the servo parameters that need setting and tuning
for high-speed and high precision operations.
To specify parameters, follow this procedure.
1. First specify one of items (1) to (3) about fixed parameters that
are dependent on the CNC model and mode to be used.
2. Specify item (4) about parameters to be tuned in common to all
CNC models and modes. (See Chapters 3 and 4 of this parameter
manual for explanations about how to tune the parameters and
detailed descriptions of the related functions.)
3. If you want to use SERVO HRV control, specify item (5).
- 580 -
HIGH-SPEED AND HIGH
(1) When HRV2 and fine ACC./Dec. is used (Series 16i/18i/21i/20i/0i)

• Using advanced preview control in the Series 16i/18i/21i
• Using AI advanced preview control in the Series 21i/20i/0i
(servo software Series 90B0)
For the above cases, make the following settings for using HRV2
control and fine acc./dec.
Parameter No.
FS16i, etc.
2003#3 1 Enables PI control function
2003#5 1 Enables backlash acceleration
0X000011
2004 (Note 1) HRV2 current control
2005#1 1 Enables feed-forward

2006#4 1 Uses the latest feedback data for velocity feedback.
2007#6 1 Enables FAD (Fine acc./dec.)
2015#6 1 Enables stage-2 backlash acceleration.
2016#3 1 Enables variable proportional gain in the stop state
2017#7 1 Enables velocity loop high cycle management function
Changes the second override format for stage-2 backlash
2018#2 1
acceleration.
2040 Standard parameter for HRV2 (Note 2) Current integral gain
2041 Standard parameter for HRV2 (Note 2) Current proportional gain
2092 10000 Advanced preview (position) feed-forward coefficient
2 (detection unit 1 µm) For variable proportional gain function in the stop state :
2119
20 (detection unit 0.1µm) judgment level for stop state (specified in detection units)
2146 50 Stage-2 backlash acceleration end timer
2202#1 1 Cutting/rapid traverse velocity loop gain variable
2209#2 1 Enables FAD of linear type.
NOTE
1 Keep the bit indicated with X (bit 6) at the standard
setting.
2 For motors not supporting the HRV2 standard
parameters, change the parameter settings to the
settings for HRV2 according to the instructions
described in Section G.4.
- Parameters whose settings must be changed according to the size of the

machine but needn’t tuning once set up
Parameter No. Standard Speed Speed Description
2109 24 16 16 FAD time constant
- 581 -
HIGH-SPEED AND HIGH
(2) When HRV2 is used, but fine acc./dec. is not (Series 30i/31i/32i/15i/16i/18i/21i/0i)
When using AI contour control I, AI contour control II, look-ahead
acc./dec. before interpolation, Fine HPCC, AI nano high precision
contour control, AI high precision contour control, AI nano contour
control, AI contour control, or high precision contour control, make
the following settings.
Parameter No.
FS30i,16i, etc. Standard setting value Description
FS15i
2003#3
1 Enables PI control function
1808#3
2003#5
1 Enables backlash acceleration
1808#5
2004
0X000011 (Note 1) HRV2 current control
1809
2005#1
1 Enables feed-forward
1883#1
2006#4
1 Uses the latest feedback data for velocity feedback.
1884#4
2015#6
1 Enables two-stage backlash acceleration
1957#6
2016#3
1 Enables variable proportional gain in the stop state
1958#3
2017#7
1 Enables velocity loop high cycle management function
1959#7
2018#2 Changes the second override format for stage-2 backlash
1
1960#2 acceleration.
2040
Standard parameter for HRV2 (Note 2) Current integral gain
1852
2041
Standard parameter for HRV2 (Note 2) Current proportional gain
1853
2092
10000 Advanced preview (position) feed-forward coefficient
1985
For variable proportional gain function in the stop state :
2119 2 (detection unit 1 µm)
judgment level for stop state
1730 20 (detection unit 0.1 µm)
(specified in detection units)
2146
50 Stage-2 backlash acceleration end timer
1769
2202#1
1 Cutting/rapid traverse velocity loop gain variable
1742#1
NOTE
setting.
- 582 -
HIGH-SPEED AND HIGH
(3) When using HRV1 and FAD (Series 21i/0i)
To use AI advanced preview control in the Series 21i/0i (servo

software Series 9096), make the following settings for using HRV1
control and fine acc./dec.
Parameter No.
FS21i
2003#3 1 Enables PI control function
2003#5 1 Enables backlash acceleration
2004 Standard parameter for HRV1 HRV1 current control
2005#1 1 Enables feed-forward
2006#4 1 Uses the latest feedback data for velocity feedback.
2007#6 1 Enables FAD (Fine acc./dec.)
2015#6 1 Enables two-stage backlash acceleration
2016#3 1 Enables variable proportional gain in the stop state
2017#7 1 Enables velocity loop high cycle management function
Changes the second override format for stage-2 backlash
2018#2 1
acceleration.
2040 Standard parameter for HRV1 Current integral gain
2041 Standard parameter for HRV1 Current proportional gain
2092 10000 Advanced preview (position) feed-forward coefficient
2 (detection unit 1 µm) For variable proportional gain function in the stop state :
2119
20 (detection unit 0.1µm) judgment level for stop state (specified in detection units)
2146 50 Stage-2 backlash acceleration end timer
2202#1 1 Cutting/rapid traverse velocity loop gain variable
2209#2 1 Enables FAD of linear type.
- Parameters whose settings must be changed according to the size of the

machine but needn’t tuning once set up
Parameter No. Standard Speed Speed Description
2109 24 16 16 FAD time constant
- 583 -
HIGH-SPEED AND HIGH
(4) Parameters common to all CNC models (requiring tuning)
- Parameters requiring tuning for finding optimum values

Parameter No.
FS30i ,16i, etc. Setting at tuning start Description Items to be referenced in tuning
FS15i
Load inertia ratio (velocity gain) While checking vibration at stop, abnormal
* When the cutting/rapid sound during low-speed movement,
2021 velocity gain switching vibration during high-speed rotation, and so
300
1875 function is used, this on, find the vibration limit, and set about
parameter is applied to rapid 70% of the limit.
traverse. → See 3.3.1(6)
Cutting load inertia ratio
While checking vibration at stop, abnormal
override (in % units)
sound during low-speed movement,
* When the cutting/rapid
2107 vibration during high-speed rotation, and so
150 velocity gain switching
1700 on, find the vibration limit, and set about
function is used, the gain
70% of the limit.
magnified by this parameter
→ See 3.3.1(6) and 4.3.
setting is applied to cutting.
After determining the velocity loop gain, find
Standard: 3000
the upper limit of the range in which hunting
1825 Speed priority I: 5000 Position gain
(low frequency vibration) does not occur.
Speed priority II: 10000
→ See 3.3.1(6).
Standard: 50
Make adjustment while observing the
2069 When nano interpolation
Velocity feed-forward coefficient shape of rounded corners.
1962 is used, see Note 2.
→ See 3.3.1(11).
200
Make adjustment while observing estimated
2047
Standard parameter Observer parameter disturbance value on the check board.
1859
→ See 4.12.1.
Make adjustment while measuring positive
2087
0 Torque offset and negative torque commands at a
1980
constant low feedrate.
Make adjustment while observing the
2048 Stage-1 acceleration amount for
30 quadrant protrusion size.
1860 two-stage backlash acceleration
→ See 4.6.7.
2039 Make adjustment while observing the
100 2nd-stage acceleration amount
2082 Stage-2 start distance Make adjustment while observing the
10
1975 (detection unit) quadrant protrusion size.
Stage-2 end distance (set with a
50 ratio to the start distance
specified in 10% units)
10 Stage-2 override
NOTE
1 There is the following relationship between the load inertia ratio and velocity loop
gain (%).
Velocity loop gain (%) = (1 + load inertia ratio/256) × 100
2 The phrase "using nano interpolation" means using AI contour control I, AI contour
control II, Fine HPCC, look-ahead acc./dec. before interpolation, AI nano high
precision contour control, or AI nano contour control.
- 584 -
HIGH-SPEED AND HIGH
(5) Parameters common to all CNC models (parameters needed to use HRV3)
Parameter No.
FS30i ,16i, etc. Standard setting value Description
FS15i
2004 HRV2 current control (in a mode other than high-speed
0X000011 (Note 1)
1809 HRV control)
2013#0 In the G05.4Q1 command, high-speed HRV control
1
1707#0 (HRV3 current control)
2202#1
1 Cutting/rapid velocity loop gain switching function
1742#1
2040
Standard parameter for HRV2 (Note 2) Current integral gain
1852
2041
Standard parameter for HRV2 (Note 2) Current proportional gain
1853
2334 Current loop gain magnification for high-speed HRV
150
2747 current control
NOTE
setting.
- Parameters that need tuning

Parameter No.
FS30i ,16i, etc. Setting Description Items to be referenced in tuning
FS15i
While checking vibration at stop, abnormal sound during
2107 Cutting load inertia ratio low-speed movement, vibration during high-speed
150
1700 override (in % units) rotation, and so on, find the vibration limit, and set about
70% of the limit.
Cutting load inertia ratio While checking vibration at stop, abnormal sound during
2335 override (in % units) low-speed movement, vibration during high-speed
200
2748 when high-speed HRV rotation, and so on, find the vibration limit, and set about
current control is in use 70% of the limit.
- 585 -
HIGH-SPEED AND HIGH
(6) Parameters for Series 30i and 31i (parameters needed to use HRV4)
Parameter No.
FS30i
0X000011 HRV3 current control (in a mode other than high-speed HRV
2004 (Note 1)
control)
In the G05.4Q1 command, high-speed HRV control (HRV4
2014#0 1
current control)
2300#0 1 Extended HRV function
2202#1 1 Cutting/rapid velocity loop gain switching function
2040 Standard parameter for HRV2 Current integral gain
2041 Standard parameter for HRV2 Current proportional gain
Current loop gain magnification for high-speed HRV current
2334 150
control
NOTE
setting.
- Parameters that need tuning

Parameter No.
Setting Description Items to be referenced in tuning
FS30i, etc.
2107 150 low-speed movement, vibration during high-speed rotation, and
so on, find the vibration limit, and set about 70% of the limit.
2335 200 low-speed movement, vibration during high-speed rotation, and
when high-speed HRV
so on, find the vibration limit, and set about 70% of the limit.
current control is in use
- 586 -
E.VELOCITY LIMIT VALUES IN
B-65270EN/07 APPENDIX SERVO SOFTWARE
E VELOCITY LIMIT VALUES IN SERVO

SOFTWARE
(1) Overview
The feed axis velocity is subject to the feedrate limits that depend on
the internal processing of the system itself and that of the servo
software. These velocity limit values on the feed axis are explained
below.
NOTE
The permissible speeds listed below do not take
detector hardware limitations into account.
- For the maximum permissible speed of a motor,
refer to the specifications of the motor.
- For the maximum permissible speed of a
detector itself, refer to the specifications of the
detector.
(2) Velocity feedback (rotation speed) limit

The following limits apply to the rotation speed of motors according
to the type of motor speed detector.
Allowable rotation
Detector type Resolution
speed
αi Pulsecoder 20 24
2 , 2 pulse/rev 7500min-1
20
HEIDENHAIN RCN220 2 pulse/rev 7500min-1
HEIDENHAIN RCN223, 723 223pulse/rev 937min-1 (*1)
HEIDENHAIN RCN727 227pulse/rev 937min-1 (*1)
(*1) The following servo software enables these permissible speeds to
be increased by a factor of up to 16 (15000 min-1) by setting bit 6
of No. 2271 to 1.
Even if any of the above detectors is used as a position detector, the

same speed limits as those given above apply as the speed limits on
the detector.
- 587 -
E. VELOCITY LIMIT VALUES IN
SERVO SOFTWARE APPENDIX B-65270EN/07
* Limit values related to linear motors

If a linear motor is used, its speed detector is a linear scale. So, a
velocity rather than a rotation speed is involved, but the same
limits as stated above are applied.
Detector type Resolution Allowable speed
HEIDENHAIN LS486 (incremental) 20/512
300m/min
with high-resolution serial output circuit µm/pulse
Sony BS75A (incremental) 0.1379/512
2.1m/min
with high-resolution serial output circuit µm/pulse
HEIDENHAIN LC191F (absolute) 0.1 µm/pulse 786m/min
HEIDENHAIN LC491F (absolute) 0.05 µm/pulse 393m/min
- 588 -
(3) Position feedback (axis feedrate) limits

The following feedrate limits may be applied according to each of the
functions because of a weight on data that is handled in detection units
within the servo software.
- When ordinary position control is exercised

(Series 15i-B, 16i-B, 18i-B, 21i-B, 20i-B, 0i-B/C, 0i Mate-B/C, Power
Mate i)
Function used Allowable feedrate
Hi-speed and high precision Detection unit of Detection unit of
Feed-forward Fine acc./dec.
function 1 µm 0.1 µm
IS-B : 196m/min
None None None
IS-C : 100m/min
Performed (conventional
None None 24m/min (*1)
type)
Not performed/ performed
None Performed
(conventional type)
Performed (advanced Not performed/ IS-B : 240m/min
Advanced preview control 98m/min
preview type) performed IS-C : 100m/min
AI contour control Performed (advanced Automatically
High precision contour control preview type) switched off
AI nano contour control
AI high precision contour control Performed (advanced Automatically
98m/min (*2)
AI nano high precision contour preview type) switched off
control
Performed (advanced Automatically IS-B : 999m/min IS-B : 196m/min
Fine HPCC
preview type) switched off IS-C : 100m/min IS-C : 100m/min
Performed (conventional IS-B : 240m/min
Electric gear box None 24m/min (*1)
type) IS-C : 100m/min
- When speed control based on a PMC axis is exercised using a position command
(Series 15i-B, 16i-B, 18i-B, 21i-B, 20i-B, 0i-B/C, 0i Mate-B/C, Power
Mate i)
Allowable feedrate
Function used
Detection unit of Detection unit of
1/1000 deg 1/10000 deg
-1
PMC-axis-based speed control (position command) 5461min 546min-1
- When ordinary position control is exercised

Hi-speed and high Detection unit Detection unit Detection unit Detection unit
Feed-forward
precision function of 1 µm of 0.1 µm of 0.01 µm of 0.001 µm
Not performed/ performed
None
(advanced preview type) IS-B:999m/min IS-B:999m/min IS-D:10m/min IS-E:1m/min
AI contour control I Not performed/ performed IS-C:100m/min IS-C:100m/min →100m/min(*3) →100m/min(*3)
AI contour control II (advanced preview type)
Performed (conventional IS-B:240m/min 2.4m/min 0.24m/min
Electric gear box 24m/min (*1)
type) IS-C:100m/min →100m/min(*3) →100m/min(*3)
- 589 -
- When rotary tool control based on a servo motor is used

Upper speed limit
Extension of Detection unit of Detection unit of Detection unit of Detection unit of
increase by a
permissible speed 1/1000 deg 1/10000 deg 1/100000 deg 1/1000000 deg
factor of 10
IS-B:2777min-1 -1
Performed IS-B:2777min
IS-D:27min-1 IS-E:2min-1
Performed (No.1408#3=0) IS-C: 277min-1 IS-C: 277min-1
(No.1013#7=0) Performed IS-B:27777min-1 IS-B:27777min-1
IS-D:277min-1 IS-E:27min-1
(No.1408#3=1) IS-C: 2777min-1 IS-C: 2777min-1
IS-B:2777min-1 -1
Performed IS-B:2777min
Performed IS-D:277min-1 IS-E:27min-1
(No.1408#3=0) IS-C: 277min-1 IS-C: 277min-1
(No.1013#7=1)
Performed IS-B:27777min-1 IS-B:27777min-1
(No.2282#3=1) IS-D:2777min-1 IS-E:349min-1
(No.1408#3=1) IS-C: 27777min-1 IS-C: 2777min-1
* In the table, the values enclosed in a box are the limits due to the
internal processing of the servo software. For the limits due to
the internal processing of the servo software, if CMR is increased
to decrease the detection unit, the permissible feedrate decreases
in proportion to the detection unit. (Reducing the detection unit
from 0.1 µm to 0.05 µm causes the permissible feedrate to be
halved.)
* If a semi-closed system (rotary or linear motor) where a detector
with a high resolution is used, using also nano interpolation
enables these functions to be used for position control at the
highest limit to the detector resolution even if the detection unit
is not subdivided.
* If you are using these functions with a larger detection unit
because of feedrate limits placed by the detection units stated
above, velocity feedback data that can seriously affect velocity
loop control is used for control at the highest limit to the detector
resolution.
(*1) If conventional feed-forward is used, the permissible
feedrate is decreased.
To avoid this, take one of the following actions:
- Disable feed-forward when not using the high
precision function.
- Use fine acc./dec. at the same time.
(*2) For AI nano contour control, AI high precision contour
control, and AI nano high precision contour control, the
limit is 98 m/min on the NC and 196 m/min on the servo
software. If CMR is increased to further decrease the
detection unit, the feedrate limit on the NC is invariable, but
the feedrate limit on the servo software decreases in
proportion to the detection unit. If the detection unit is
decreased, therefore, the feedrate limit will be the smaller
one.
- 590 -
Detection unit Limit on the NC Limit on the servo

software
0.1µm 98m/min 196m/min
0.01µm 98m/min 19.6m/min
(*3) With the servo software and system software indicated
below, the allowable feedrate value applicable when an
increment system is selected from IS-D and IS-E is
extended. A feedrate of up to 100 m/min can be specified
with the increment system IS-D or IS-E by using matching
servo software and system software and setting the
following parameters:
• Series and editions of applicable servo software
• Series and editions of applicable system software
Series 30i-A:
Series G002, G012, and G022/04.0 and subsequent
editions
Series 31i-A:
Series G101, G111/04.0 and subsequent editions
Series 31i-A5:
Series G121, G131/04.0 and subsequent editions
Series 32i-A:
Series G201/04.0 and subsequent editions (IS-E is
not supported.)
• Parameter setting method
To extend the feedrate with the increment system IS-D
or IS-E, both of parameter No. 1013 and No. 2282
must be set to 1. (The increment systems IS-D and
IS-E are optional functions.)
- 591 -
#7 #6 #5 #4 #3 #2 #1 #0
1013（FS30i） IESP
IESP(#7) When the increment system IS-D or IS-E is used, the function that can
set a value range wider than the conventionally allowed one for speed
and acceleration parameters is:
0: Not used.
1: Used.
With an axis for which this parameter is set, a value range wider than
the conventionally allowed one can be set for parameters to be set in
speed and acceleration units when the increment system IS-D or IS-E
is selected.
Moreover, a movement can be made at a parameter-set speed.
The number of fractional digits displayed on the parameter input
screen for an axis with this parameter set is also modified. When IS-D
is used, the number of fractional digits is reduced by 1 from the
conventional number of fractional digits. When IS-E is used, the
number of fractional digits is reduced by 2 from the conventional
number of fractional digits.
NOTE
#7 #6 #5 #4 #3 #2 #1 #0
2282 (FS30i) ISE64
ISE64(#3) The speed limit on feed-forward (bit 1 (FEED) of parameter No. 2005
= 1) is:
0: Applied as conventionally done.
1: Extended.
When feed-forward is enabled, the speed limit on an axis for which
this parameter is set is extended if the increment system is IS-D or
IS-E.
- 592 -
B-65270EN/07 APPENDIX F.SERVO FUNCTIONS
F SERVO FUNCTIONS
Servo software series 9 9 9 9 99 9 9
0 0 00 00 0 0 Reference items in
9 B BB BB D E this manual
Name of function 6 0 65 81 0 0
[Servo initial setting]
Flexible feed gear function A A A A A A 2.1
Position feedback pulses conversion coefficient - A A A A A 2.1.8 Supplementary 3
Supporting a fraction in reference counter setting - A A A A A 2.1.3
Supporting serial-type separate detectors - A A A A A 2.1.4
Supporting high-resolution serial output circuits H and C - Q A A A A 2.1.4
Supporting linear motor position detection circuits H and C - Q A A A A 4.14.1
Improving the reference counter when the RCN723 or RCN223 is used - Q A A A A 2.1.4
Supporting RCN723 (serial separate detector) - - - B J J 2.1.4
Supporting RCN723 (synchronous built-in servo) - - - F J J 4.15.1
Supporting analog input separate detector interface unit - - - - J J 2.1.5
Supporting αiCZ512AS,1024AS (serial separate detector) - A A A A A 2.1.6
Supporting αiCZ512A,1024A (synchronous built-in servo) - - - A A A 2.1.6, 4.15.1
Supporting αiCZ768AS (serial separate detector) - A A A A A 2.1.6
Supporting αiCZ768A (synchronous built-in servo motor) - - - C J J 2.1.6, 4.15.1
Acceleration sensor - - - F L L 2.1.7
Temperature detection circuit - - - K P P 2.1.7
Illegal parameter setting alarm detail output A A A A A A 2.1.8
Automatic format change for position gain - A A A A A 2.1.8 Supplementary 5
Expanding the position gain setting range A A A A A A 2.1.8 Supplementary 5
[Servo functions]
SERVO HRV control A A A A - - 4.1
SERVO HRV2 control - A A A A A 4.1.1
SERVO HRV3 control (high-speed HRV current control) - A A A A A 4.2.1
SERVO HRV4 control (high-speed HRV current control) - - - - A - 4.2.2
Cutting/rapid velocity loop gain switching function A A A A A A 4.3
1/2 PI is always enabled for cutting/rapid velocity gain - A A A A A 4.3
Upper limit to cutting/rapid velocity loop gain loop of 400% - A A A A A 4.3
Velocity loop high cycle management function A A A A A A 4.4.1
Supporting the tandem velocity loop high cycle management function - A A A A A 4.4.1, 4.21
Acceleration feedback function A A A A A A 4.4.2
Variable proportional gain function in the stop state A A A A A A 4.4.3
Variable proportional gain function in the stop state : supporting 50% A A A A A A 4.4.3
Variable proportional gain function in the stop state : supporting arbitrary
- A A A A A 4.4.3
magnification
Addition of N pulses suppression function A A A A A A 4.4.4
Current loop 1/2 PI control function A A A A A A 4.4.5
Current loop 1/2 PI control function always enabled A A A A A A 4.4.5
Current loop PI control function current control PI ratio variable - A A A A A 4.4.5
TCMD filter A A A A A A 4.5.2
- 593 -
F.SERVO FUNCTIONS APPENDIX B-65270EN/07

TCMD filter (cutting/rapid) A A A A A A 4.5.2
Resonance elimination filter : stage 1 - A A A A A 4.5.3
Resonance elimination filter : stage 4 - J A A A A 4.5.3
Active resonance elimination filter - P A A A A 4.5.3
Disturbance elimination filter - A A A A A 4.5.4
Resonance elimination filter L - - - I P P 4.5.5
Observer function A A A A A A 4.5.6
Observer function (with the disable function for observer in the stop
A A A A A A 4.5.6
state added)
Vibration damping control function A A A A A A 4.5.7
Dual position feedback function A A A A A A 4.5.8
Machine speed feedback function A A A A A A 4.5.9
Machine speed feedback function (normalization) A A A A A A 4.5.9
Machining point control - - - I P P 4.5.10
Feed-forward function A A A A A A 4.6.1
Advanced preview feed-forward function A A A A A A 4.6.2
RISC feed-forward function A A A A - - 4.6.3
Feed-forward timing adjustment A A A A A A 4.6.5
Feed-forward timing adjustment (for supporting FAD) - J A A - - 4.6.5
Cutting/rapid feed-forward switching function - B A A A A 3.4, 4.6.4
Backlash acceleration function A A A A A A 4.6.6
Supporting backlash acceleration override function - W A A J J 4.6.6
Backlash acceleration stop function A A A A A A 4.6.6
Two-stage backlash acceleration function A A A A A A 4.6.7
Two-stage backlash acceleration function : second stage acceleration
- J A A A A 4.6.7
limit
Two-stage backlash acceleration function : second stage acceleration
- J A A A A 4.6.7
direction-specific setting
Two-stage backlash acceleration function: second stage acceleration
- X A A A A 4.6.7
(type 2)
Backlash acceleration function : enabled only for cutting A A A A A A 4.6.7
Backlash acceleration function : improvement on "enabled only for
- C A A A A 4.6.7
cutting"
Static friction compensation function A A A A A A 4.6.8
Torsion preview control - W A A M M 4.6.9
Overshoot compensation function A A A A A A 4.7
Overshoot compensation function type 2 A A A A A A 4.7
Position gain switching function A A A A A A 4.8.1
position gain switching function type 2 A A A A A A 4.8.1
Expanding the velocity setting range for high-speed positioning function A A A A A A 4.8.1
Low-speed integral function A A A A A A 4.8.2
Fine acc./dec. function A A A A - - 4.8.3
Cutting/rapid fine acc./dec. switching function A A A A - - 3.4, 4.8.3
Synchronization in rigid tapping mode when the FAD function is used A A A A - - 4.8.3
Serial feedback dummy function - A A A A A 4.9.1
Dummy function for separate detector - A A A A A 4.9.1
Dummy axis ready signal output - - - F L L 4.9.2
Brake control function A A A A A A 4.10
- 594 -
B-65270EN/07 APPENDIX F.SERVO FUNCTIONS

Quick stop type 1 at emergency stop A A A A A A 4.11.1
Quick stop type 2 at emergency stop A A A A A A 4.11.2
Lifting function against gravity at emergency stop - P A A A A 4.11.3.1
Switching based on the DI signal for the lifting function against gravity at
- - - H P P 4.11.3.2
emergency stop
Quick stop function for hardware disconnection of separate detector A A A A A A 4.11.4
Quick stop function for separate detector alarms - - - E L L 4.11.5
Quick stop function at the OVC and OVL alarm A A A A A A 4.11.6
Unexpected disturbance torque detection function A A A A A A 4.12.1
Improvement on dynamic friction compensation for estimated
- E A A A A 4.12.1
disturbance
2-axes simultaneous retract function related to unexpected disturbance
- E A A A A 4.12.1
torque detection
Cutting/rapid unexpected disturbance torque detection switching
A A A A A A 4.12.2
function
Unexpected disturbance torque detection switching function depending
- - - H P P 4.12.3
on acc.
Current offset acquisition at an emergency stop A A A A A A 4.13
Supporting linear motors A A A A A A 4.14.1
Expanding the AMR offset setting range for linear motors - C A A A A 4.14.1
Current gain internally 4 times function - A A A A A 4.14.1
Function of changing the velocity loop proportional gain format A A A A A A 4.14.1
Overheat via the PMC - - B C J J 4.14.2
Overheat via the αiCZ, linear motor detection circuit, or temperature
- - - K P P 4.14.2
detection circuit
Linear motor smoothing compensation A A A A A A 4.14.3
Linear motor smoothing compensation : supporting direction-specific
- N A A A A 4.14.3
operations
Support for a synchronous built-in servo motor - - - A A A 4.15.1
Support for the pole position detection function - - - B A A 4.15.1
Support for the detach function for the pole position detection function - - - - M M 4.15.1
Support for RCN727 for synchronous built-in servo motor - - - F J J 4.15.1
Non-binary detector for synchronous built-in servo motor - - - C J J 4.15.1
Smoothing compensation for synchronous built-in servo motor - - - E L L 4.15.1
Support for the PWM distribution module (PDM) - - - A - - 4.16.3
PWM distribution module (PDM) current monitor - - - F - - 4.16.4
PWM distribution module (PDM) ready output - - - H - - 4.16.4
Interactive Force Compensation - - - - P P 4.17
Torque control function type 1 A A A A A A 4.18
Torque control function type 2 A A A A A A 4.18
Tandem disturbance elimination control function - A A A A A 4.19
Synchronous axes automatic compensation function - V A A - - 4.20
Synchronous axes automatic compensation function (dead-band width) - - - A - - 4.20
Tandem disturbance elimination control function A A A A A A 4.21
Tandem control function (preload function) A A A A A A 4.21.1
Tandem control function (damping compensation function) A A A A A A 4.21.2
Tandem control function (velocity feedback average function) A A A A A A 4.21.3
Tandem control function (servo alarm 2-axes simultaneous monitor) A A A A A A 4.21.4
- 595 -
F.SERVO FUNCTIONS APPENDIX B-65270EN/07

Servo alarm 2-axes simultaneous monitor : supporting VRDY OFF
- C A A A A 4.21.4
invalidation
Tandem control function (motor feedback sharing function) A A A A A A 4.21.5
Tandem control function (position feedback switching) A A A A A A 4.21.7
Velocity loop integrator copy function - N A A A A 4.21.9
Tandem speed difference alarm function - - - C L L 4.21.10
Supporting SERVO GUIDE A F A A C C 4.22
Supporting SERVO GUIDE and tuning navigator - T A A C C 4.22
Disturbance input function (frequency characteristic measurement) - A A A A A Appendix H
High-speed data output to the check board - A A A - - Appendix I
Servo check board interface unit - - - - N N Appendix J
Changing the check board output magnification for TCMD and SPEED
- N A A A A Appendix I, Appendix J
signals
[CNC functions]
Supporting PMC-based velocity loop gain override A A A A A A
Supporting the EGB function - A A A A A
Supporting the high-speed response function - A A A A A
Supporting nano interpolation - A A A A A
- 596 -
G.PARAMETERS FOR α AND
B-65270EN/07 APPENDIX OTHER SERIES
G PARAMETERS FOR α AND OTHER

SERIES
The motor ID numbers necessary to automatically set parameters for
the α series, β series, and conventional linear motors are explained
below.
Search for the motor ID number of the motor used, based on the motor
model and the drawing number (4-digit number in the middle of
A06B-****-B***).
NOTE
The motor ID numbers for consecutive (odd and
even) servo controlled axis numbers must be for
one of servo HRV1, servo HRV2, or servo HRV3.
Appendix G, "PARAMETERS FOR α AND OTHER SERIES",

consists of the following sections:
G.1 MOTOR ID NUMBERS OF α SERIES MOTORS.................598

G.2 MOTOR ID NUMBERS OF β SERIES MOTORS .................600
G.3 MOTOR ID NUMBERS OF CONVENTIONAL LINEAR
MOTORS..................................................................................601
G.4 PARAMETERS FOR SERVO HRV2 CONTROL..................602
G.5 HRV1 CONTROL PARAMETERS FOR α SERIES, β SERIES,
AND CONVENTIONAL LINEAR MOTORS ........................603
G.6 HRV2 CONTROL PARAMETERS FOR βM SERIES
MOTORS..................................................................................612
- 597 -
G. PARAMETERS FOR α AND
OTHER SERIES APPENDIX B-65270EN/07
G.1 MOTOR ID NUMBERS OF α SERIES MOTORS
α series servo motor
Motor
specification
α1/3000 0371 61 A A
α2/2000 0372 46 A A
α2/3000 0373 62 A A
α3/3000 0123 15 A A
α6/2000 0127 16 A A
α6/3000 0128 17 A A
α12/2000 0142 18 A A
α12/3000 0143 19 A A
α22/1500 0146 27 A A
α22/2000 0147 20 A A
α22/3000 0148 21 A A
α30/1200 0151 28 A A
α30/2000 0152 22 A A
α30/3000 0153 23 A A
α40/2000 0157 30 A A
α40/2000FAN 0158 29 A A
α65/2000 0331 39 A A
α100/2000 0332 40 A A
α150/2000 0333 41 A A
α300/1200 0135 113 A A
α300/2000 0137 115 A A
α400/1200 0136 114 A A
α400/2000 0138 116 A A
α1000/2000 0131 117 S E
The motor ID numbers are for servo HRV1.
αM series servo motor
Motor
specification
αM/3000 0376 98 A A
αM2.5/3000 0377 99 A A
αM3/3000 0161 24 A A
αM6/3000 0162 25 A A
αM9/3000 0163 26 A A
αM22/3000 0165 100 A A
αM30/3000 0166 101 A A
αM40/3000 0169 110 A A
108 (360-A driving) A A
αM40/3000FAN 0170
109 (240-A driving) A A
- 598 -
αL series servo motor
Motor
specification
αL3/3000 0561 68 A A
αL6/3000 0562 69 A A
αL9/3000 0564 70 A A
αL25/3000 0571 59 A A
αL50/2000 0572 60 A A
αC series servo motor
Motor
specification
α/2000 0121 7 A A
αC6/2000 0126 8 A A
αC12/2000 0141 9 A A
αC22/1500 0145 10 A A
αHV series servo motor
Motor
specification
α3/3000HV 0171 1 A A
α6/3000HV 0172 2 A A
α12/3000HV 0176 3 A A
4 (40-A driving)
α22/3000HV 0177 A A
102 (60-A driving)
5 (40-A driving)
α30/3000HV 0178 A A
103 (60-A driving)
α40/3000HV 0179 118 A A
αMHV series servo motor
Motor
specification
αM6/3000HV 0182 104 A A
αM9/3000HV 0183 105 A A
αM22/3000HV 0185 106 A A
αM30/3000HV 0186 107 A A
αM40/3000HV 0189 119 A A
- 599 -
G.2 MOTOR ID NUMBERS OF β SERIES MOTORS
β series servo motor
Motor
specification
β0.5/3000 0113 14 (20-A driving) N D
β1/3000 0031 11 (20-A driving) N D
β2/3000 0032 12 (20-A driving) N D
β3/3000 0033 33 A A
β6/2000 0034 34 A A
βM series servo motor
Motor
specification
βM0.2/4000 0111 * (260) N *
βM0.3/4000 0112 * (261) N *
βM0.4/4000 0114 * (280) N *
βM0.5/4000 0115 181(281) N D
βM1/4000 0116 182(282) N D
The motor ID numbers not enclosed in parentheses are for servo
HRV1, and the motor ID numbers enclosed in parentheses are for
servo HRV2 and HRV3.
* For βM0.2, βM0.3, and βM0.4, HRV1 control cannot be used. It
cannot, therefore, be used in Series 9096.
(Reference)
In the parameter table in item 4, two motor ID numbers are
assigned to the same β series servo motor. One of them is the
parameter for driving the motor with an α/β series servo
amplifier (12A). Use caution not to use the wrong type number.
α servo amplifier drive αi servo amplifier drive

Maximum Maximum
Motor model
amplifier Motor ID No. amplifier Motor ID No.
β0.5/3000 12 13 20 14
β1/3000 12 35 20 11
β2/3000 12 36 20 12
- 600 -
G.3 MOTOR ID NUMBERS OF CONVENTIONAL LINEAR

MOTORS
Linear motor
Motor
specification
300D/4 0421 124 A A
600D/4 0422 125 A A
900D/4 0423 126 A A
1500A/4 0410 90 A A
3000B/2 0411 91 A A
3000B/4 0411-B811 120 A A
6000B/2 0412 92 A A
6000B/4 0412-B811 127 (160-A driving) R D
9000B/2 0413 128 (160-A driving) N D
9000B/4 0413-B811 129 (360-A driving) Q D
15000C/2 0414 130 (360-A driving) Q D
15000C/3 0414-B811 123 A A
The motor ID numbers are for servo HRV1. Loading is possible with
the servo software of the series and edition listed above or subsequent
editions.
(Reference)
In the parameter table in item 4, two motor ID numbers are
assigned to the same linear motor. One of them is the parameter
for driving the motor with an α series servo amplifier (130A or
240A). Use caution not to use the wrong type number.
α servo amplifier drive αi servo amplifier drive

Motor Maximum Maximum
model amplifier Motor ID No. amplifier Motor ID No.
6000B/4 240 121 160 127
9000B/2 130 93 160 128
9000B/4 240 122 360 129
15000C/2 240 94 360 130
- 601 -
G.4 PARAMETERS FOR SERVO HRV2 CONTROL
By converting parameter settings as shown below, servo HRV1

control parameters can be changed to parameters for servo HRV2
control.
NOTE
This section explains the conversion method to be
applied when only servo HRV1 control parameters
are provided. For motors for which servo HRV2
control parameters are provided, use these servo
HRV2 control parameters.
<1> To set the current control period to 125 µs, set the following:
#7 #6 #5 #4 #3 #2 #1 #0
1809 (FS15i) Conventional DLY1 DLY0 TIB1 DLY2 TRW1 TRW0 TIB0 TIA0
setting
2004 (FS30i, 16i) 0 X 0 0 0 1 1 0
When servo HRV2 control is used DLY1 DLY0 TIB1 DLY2 TRW1 TRW0 TIB0 TIA0
0 X 0 0 0 0 1 1
The standard setting at the bit marked by X (bit 6) must be left
unchanged.
<2> Changing the current loop gain (integral)
1852 (FS15i) Current integral gain

2040 (FS30i, 16i)
Set a value obtained by multiplying the standard parameter value by
0.8.
<3> Changing the current loop gain (proportional)
1853 (FS15i) Current proportional gain

2041 (FS30i, 16i)
Set a value obtained by multiplying the standard parameter value by
1.6.
- 602 -
G.5 HRV1 CONTROL PARAMETERS FOR α SERIES, β

SERIES, AND CONVENTIONAL LINEAR MOTORS
The HRV1 control parameters for the α series, β series, and conventional
linear motors are given in the table below.
9096 series
90B0 series
- 603 -
Motor model α3HV α6HV α12HV α22HV α30HV αC3 αC6 αC12 αC22 β1/3 β2/3
Motor 0171 0172 0176 0177 0178 0121 0126 0141 0145 0031 0032
specification (40A) (40A) (20A) (20A)
Motor ID No. 1 2 3 4 5 7 8 9 10 11 12
Symbol FS15i FS16i,etc.
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 01000110 01000110 01000110 01000110 01000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 01000100 01000100 01000100 01000100 01000100 01000100 01000100 01000000 01000000 01000000 01000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00100000 00100000 00100000 00100000 00000000 00000000 00000000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001100 00001100
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001100 00001100
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 687 828 730 800 1100 1600 1800 3000 2330 598 1173
PK2 1853 2041 -2510 -3129 -3038 -3190 -3886 -5059 -6105 -9750 -6831 -1882 -4002
PK3 1854 2042 -2617 -2638 -2638 -2694 -2663 -2608 -2641 -2687 -2694 -2564 -2596
PK1V 1855 2043 107 127 188 271 293 107 127 251 271 61 37
PK2V 1856 2044 -955 -1141 -1683 -2426 -2625 -955 -1140 -2245 -2426 -550 -667
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3972 3326 2254 1564 1446 3974 3329 1690 1564 -690 5692
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 3787 3787 3787 3787 3787 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 2500 4000 -12840 3500 4000 3046 4381 4000 4000 2500 3300
PVPA 1869 2057 2200 -7692 -6925 -6671 -4113 -6405 -3858 -3094 -3872 2100 -10246
PALPH 1870 2058 70 -1920 -2832 -3000 -3400 -250 -2500 -4000 -2800 43 -960
PPBAS 1871 2059 5 5 5 5 5 5 5 5 5 5 5
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 4369 4369
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32686 32637 32568 32370 32359 32686 32637 32412 32370 32605 32522
POVC2 1878 2063 1031 1639 2505 4981 5110 1030 1636 4446 4981 2034 3077
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 3059 4866 7445 14847 15235 3056 4858 13245 14847 2014 3051
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 0 8192 16288 16288 12192 16288 11192 8192 8192 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1287 1623 2008 2836 2872 1286 1622 2678 2836 1044 1285
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 5145 5145 5170 10250 15370 12800 17920 17920 12800 80 2786
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 15000 15000 15000 15000 15000 0 0 0 0 7200
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 205 325 527 684 921 205 326 395 684 86 139
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 2568 0 16 2592 2576 16 24 16 24 1536 1536
DETQLM 1704 2111 6244 3870 5140 3915 3147 0 5220 0 2660 7784 7740
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1700 300 3420 700 900 2729 3326 4520 3298 0 0
MFWKCE 1736 2128 3333 4286 2000 2667 3636 4000 6500 6000 7000 0 5000
MFWKBL 1752 2129 2578 2076 2581 2574 1813 1048 1047 785 1042 0 4128
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 0 5140
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 0 7720
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 25 25 45 45 45 25 25 25 45 25 25
- 604 -
Motor model β0.5/3 β0.5/3 α3/3 α6/2 α6/3 α12/2 α12/3 α22/2 α22/3 α30/2 α30/3
(12A) (20A)
Motor ID No. 13 14 15 16 17 18 19 20 21 22 23
1808 2003 00001000 00001000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 01000100 01000100 01000100 01000000 01000100 01000100 01000100 01000100 01000100 01000100 01000100
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00100000 00100000 00100000 00000000 00100000 00100000 00100000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00001100 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00001100 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000010 00000010 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 220 367 1183 2054 754 3121 1324 1975 881 3173 1175
PK2 1853 2041 -540 -900 -2941 -4194 -2363 -4953 -3671 -4041 -2759 -5522 -3088
PK3 1854 2042 -2556 -2556 -3052 -3052 -2633 -3052 -3052 -3052 -3052 -3052 -3052
PK1V 1855 2043 9 5 87 99 91 188 165 203 214 144 240
PK2V 1856 2044 -79 -48 -781 -887 -818 -1683 -1474 -1821 -1921 -1293 -2153
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -4789 -7981 4858 4279 4639 2254 2574 2084 1976 2935 1763
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 1200 1200 2000 3500 -12820 -6440 -12840 4000 -12820 -12840 4500
PVPA 1869 2057 2000 2000 -7690 -6415 -3845 -5135 -7690 -3590 -8970 -3097 -5130
PALPH 1870 2058 77 46 -800 -1600 -650 -1500 -1500 -2000 -1226 -1120 -2500
PPBAS 1871 2059 5 5 5 5 5 5 5 5 5 5 5
TQLIM 1872 2060 7282 4369 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32585 32570 32713 32689 32698 32568 32614 32543 32518 32668 32493
POVC2 1878 2063 2288 2470 690 991 877 2505 1922 2811 3128 1245 3443
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 6797 2447 2045 2940 2601 7445 5709 8358 9305 3695 10245
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 17384 0 3000 8192 0 10192 18384 18384 14288 14288 9192
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1918 1151 1052 1261 1187 2008 1758 2127 2245 1414 2355
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 5160 5160 0 10265 30 12800 5145 7680 2585 10240 5145
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 9000 15000 15000 15000 0 15000 15000 15000 0 15000
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 29 49 251 419 454 527 601 911 864 1870 1123
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 32 32 32 0 16 0 24 20 0
DETQLM 1704 2111 7790 7790 6214 3960 5170 5220 0 3468 5170 4040 3890
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 400 400 2047 2729 1706 4037 2615 2956 1663 4989 2000
MFWKCE 1736 2128 0 0 1500 5000 1000 5000 2000 6000 2000 6000 6000
MFWKBL 1752 2129 0 0 1812 1556 2076 1045 1551 1300 2571 1044 2581
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 3880 0 3880 5160
PHDLY2 1757 2134 0 0 0 0 0 0 0 12820 0 12820 12840
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 12 25 40 40 80 45 85 85 135 135 135
- 605 -
Motor model αM3 αM6 αM9 α22/1.5 α30/1.2 α40/FAN α40/2 β3/3 β6/2 β1/3 β2/3
(12A) (12A)
Motor ID No. 24 25 26 27 28 29 30 33 34 35 36
1808 2003 00001000 00001000 00001000 00000000 00000000 00000000 00000000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 01000100 01000100 01000100 01000000 01000000 01000100 01000100 01000000 01000000 01000000 01000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00000000 00000000 00000000 00100000 00100000 00100000 00100000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000010 00000000 00000000 00000010 00000010 00000010 00000010 00000000 00000010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 538 950 748 2330 5060 1649 1649 629 990 359 704
PK2 1853 2041 -1652 -2582 -2402 -6381 -9923 -5395 -5395 -2093 -3544 -1129 -2401
PK3 1854 2042 -3052 -3052 -2632 -2694 -2705 -2700 -2700 -2622 -2632 -2564 -2596
PK1V 1855 2043 53 38 61 271 147 201 201 144 144 102 62
PK2V 1856 2044 -471 -328 -550 -2426 -1313 -1801 -1801 -2587 -2587 -916 -1111
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -806 -1156 -690 1564 2891 2107 2107 1467 1467 4141 3415
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 2500 3500 3000 4000 8000 -12820 -12820 3000 3200 2500 3300
PVPA 1869 2057 2400 -3590 -6407 -3872 -2078 -3855 -3855 -10250 -6420 2100 -10250
PALPH 1870 2058 70 -1440 -1600 -2800 -1800 -2400 -2400 -1600 -1600 71 -1600
PPBAS 1871 2059 5 5 5 5 5 5 5 5 5 5 5
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32697 32727 32692 32370 32665 32361 32579 32456 32456 32617 32540
POVC2 1878 2063 886 516 955 4981 1283 5090 2358 3897 3897 1884 2850
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 2627 1529 2832 14847 3809 15175 7007 11600 11600 5594 8474
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 3000 31672 12288 12288 12288 14288 14288 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1193 910 1238 2836 1436 2867 1948 2506 2506 1740 2142
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 25 5145 0 12800 12800 12800 12800 -1476 30 80 -2786
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 15000 0 0 0 15000 15000 15000 12000 0 12000
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 221 581 653 684 1842 1756 1756 107 215 51 83
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 24 24 32 24 28 20 20 0 0 0 0
DETQLM 1704 2111 5220 5220 5220 2660 0 3920 3920 2640 3890 7784 7740
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1990 2729 853 3298 7846 3326 3326 0 0 0 0
MFWKCE 1736 2128 2000 2500 2000 7000 9500 7000 7000 0 5000 0 3000
MFWKBL 1752 2129 2588 1298 2570 1042 788 1300 1300 0 2064 0 4128
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 5140 0 0 20 20 6164 2573 0 5140
PHDLY2 1757 2134 0 0 12840 0 0 12840 12840 12840 12850 0 12840
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 40 80 85 47 85 135 135 25 25 12 12
- 606 -
Motor model α65/2 α100/2 α150/2 α2/2 αL25 αL50 α1/3 α2/3 αL3 αL6 αL9
Motor ID No. 39 40 41 46 59 60 61 62 68 69 70
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 01000110 01000110 01000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00010000 00010000 00010000 00000000 00000000 00000000 01000100 01000100 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000110 00000000 00000000 00000000
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 790 1578 1574 1170 574 700 390 530 757 855 737
PK2 1853 2041 -3473 -4761 -4809 -2289 -2254 -2000 -1053 -1653 -3394 -3610 -2588
PK3 1854 2042 -2714 -2714 -2718 -2485 -2700 -2701 -2480 -2490 -2652 -2676 -2673
PK1V 1855 2043 121 102 120 91 92 116 111 128 18 17 35
PK2V 1856 2044 -1085 -916 -1072 -812 -825 -1035 -997 -1146 -158 -155 -309
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 3498 4141 3541 4674 4599 3666 3806 3311 -2395 -2455 -1227
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 3787 3787 3787 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 4444 4884 6668 2147 4500 4800 2800 2520 2000 2000 1240
PVPA 1869 2057 -4617 -4617 -3849 -7690 -7692 -6430 2330 -6156 0 0 -10249
PALPH 1870 2058 -1620 -1620 -1890 -1000 -2200 -3300 57 -1200 0 0 -800
PPBAS 1871 2059 20 20 20 0 5 5 5 5 5 5 5
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 120 120 120 120 120 120 120 120 120 120 120
POVC1 1877 2062 32482 32529 32332 32627 32476 32214 32623 32519 32693 32696 32607
POVC2 1878 2063 3569 2987 5452 1766 3644 6929 1811 3112 940 894 2010
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 10622 8881 16262 5245 10844 20705 5377 9256 2787 2653 5970
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 1100 1100 1100 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 28672 20480 20480 0 24576 0 1680 8194 16384 28672 20480
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2398 2193 2968 1685 2423 3349 1706 2239 1228 1198 1798
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 50 0 50 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 15000 15000 15000 15000 15000 15000 15000 15000 15000 15000
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 2438 4103 4548 104 928 1343 51 74 219 450 450
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 12 0 0 0 20 24 0 0 64 64 16
DETQLM 1704 2111 2148 0 0 6194 50 0 7715 7780 2650 2620 5160
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 4800 0 2402 785 2300 2000 2500 2500
MFWKCE 1736 2128 3600 4800 3500 2500 2000 4000 0 3000 0 0 2500
MFWKBL 1752 2129 1551 1294 1033 1806 2567 2321 0 3088 0 0 2586
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 7710 7710 0 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 12830 12830 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 245 365 365 12 135 135 12 12 40 85 85
- 607 -
Motor model 1500A 3000B 6000B 9000B 15000C αM2 αM2.5 αM22 αM30 α22/3HV α30/3HV
Linear Linear Linear Linear Linear
Motor ID No. 90 91 92 93 94 98 99 100 101 102 103
Symbol FS15i FS16i,etc. (130A) (240A) (60A) (60A)
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 01000100 01000100
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000100 00000100 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00100000 00100000 00100000 00100000 00100000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000100 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000000
2713 2300 10000000 10000000 10000000 10000000 10000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1890 4804 4804 5036 1420 600 400 555 736 1050 1100
PK2 1853 2041 -7180 -14453 -13138 -16000 -5600 -1957 -1154 -2698 -2623 -3811 -4300
PK3 1854 2042 -2647 -2660 -2660 -2660 -2663 -2476 -2547 -2686 -2696 -2694 -2663
PK1V 1855 2043 19 16 16 14 10 31 56 97 128 181 195
PK2V 1856 2044 -260 -214 -214 -195 -131 -274 -500 -867 -1142 -1618 -1750
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -4371 -5321 -5321 -5849 -8681 -1383 -759 4378 3322 2346 2168
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 0 0 0 0 0 -9230 -8722 -7695 -3870 -6412 -3856
PALPH 1870 2058 0 0 0 0 0 -1400 -1800 -2700 -2240 -2240 -3000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 120 120 120 120 120 0 0 0 0 0 0
POVC1 1877 2062 32670 32670 32670 32685 32712 32685 32645 32587 32567 32590 32586
POVC2 1878 2063 1222 1222 1222 1041 703 1041 1535 2260 2514 2221 2279
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 3626 3626 3626 3087 2086 3089 4556 6714 7473 6599 6771
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 0 0 0 0 0 20480 8192 12288 8192 20480 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1402 1402 1402 1293 1063 1293 1730 1907 2012 1890 1915
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 15000 15000 15000 15000 15000 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 227 455 911 1481 3104 139 143 943 1341 1026 1381
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 0 0 2600 2584 40 24 2584 2592
DETQLM 1704 2111 0 0 0 0 0 6440 7780 5220 5220 5145 4658
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 0 0 0 0 1322 625 1802 1756 4200 5885
MFWKCE 1736 2128 0 0 0 0 0 2000 2500 0 3000 2778 4000
MFWKBL 1752 2129 0 0 0 0 0 2578 3847 0 2577 1554 1287
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 2590 0 0
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 12815 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 45 45 85 135 245 25 25 135 135 60 60
- 608 -
Motor model αM6HV αM9HV αM22HV αM30HV α α α α300/1.2 α400/1.2 α300/2 α400/2
Motor ID No. 104 105 106 107 108 109 110 113 114 115 116
Symbol FS15i FS16i,etc. (360A) (240A) (130A)
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 01000110 01000110 00000110 01000110 01000110 01000110 01000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00100000 00100000 00100000 00100000 00100000 00100000 00000000 00100000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 783 542 430 648 1046 968 822 1715 2910 1357 1593
PK2 1853 2041 -2832 -2277 -2470 -2532 -4459 -3716 -2254 -5809 -7671 -4212 -5395
PK3 1854 2042 -2607 -2640 -2682 -2692 -2664 -2664 -2664 -2711 -2712 -2710 -2711
PK1V 1855 2043 37 66 94 161 43 65 119 116 112 114 113
PK2V 1856 2044 -329 -595 -845 -1444 -386 -579 -1069 -1035 -1003 -1023 -1016
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -1154 6373 4490 2628 -983 -656 3551 3668 3782 3709 3736
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 3787 3787 1894 3787 3787 3787 3787
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -7690 -6408 -5135 -6422 -3852 -3858 -3873 -2323 -1822 -3850 -2838
PALPH 1870 2058 -1800 -1800 -2000 -3226 -1800 -2700 -4950 -2000 -4000 -800 -2000
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 8010 8010 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 120 120 120 120
POVC1 1877 2062 32725 32678 32596 32447 32613 32420 32279 32343 32366 32352 32356
POVC2 1878 2063 538 1119 2149 4009 1937 4345 6107 5312 5020 5196 5145
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 1596 3321 6385 11935 5752 12943 18231 15843 14964 15494 15339
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 28672 12288 24576 0 20480 20480 0 16384 12288 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 929 1341 1859 2542 1453 2180 2302 2412 2344 2385 2373
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 15000 15000 15000 15000 15000 15000 15000 0 15000 15000
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 580 603 967 1061 4330 2887 1563 10808 14575 10931 14398
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 40 40 40 24 0 0 1 16 16 16 24
DETQLM 1704 2111 0 5220 3940 5220 0 0 4174 0 0 1606 1636
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 5572 853 4051 2388 5116 3411 1848 0 0 0 0
MFWKCE 1736 2128 0 0 0 1000 2000 5000 2000 7500 5000 5500 6500
MFWKBL 1752 2129 0 0 0 3221 1287 1551 2051 787 272 791 784
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 0 0 0 0 0 0 1556 1550
PHDLY2 1757 2134 0 0 0 0 0 0 0 0 0 20494 20494
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT 1787 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 45 45 65 65 365 245 135 245 245 365 365
- 609 -
Motor model α1000/2 α40HV αM40HV 3000B/4N 6000B/4N 9000B/4N 15000C/3N 300D/4 600D/4 900D/4 6000B/4N
Motor specification 0131 0179 0189 0411-B811 0412-B811 0413-B811 0414-B811 0421 0422 0423 0412-B811
Linear Linear Linear Linear Linear Linear Linear Linear
Motor ID No. 117 118 119 120 121 122 123 124 125 126 127
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 01000110 01000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 01000100 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
1955 2011 00100000 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2713 2300 00000000 00000000 00000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1170 715 600 1620 2626 4944 2392 526 717 390 1751
PK2 1853 2041 -3684 -3141 -2020 -11180 -10051 -11831 -8448 -2141 -3333 -2009 -6701
PK3 1854 2042 -2722 -2699 -2680 -2660 -2660 -2660 -2657 -2618 -2618 -2618 -2660
PK1V 1855 2043 234 230 120 16 10 16 10 16 9 13 15
PK2V 1856 2044 -2100 -2061 -1077 -214 -135 -211 -128 -217 -122 -179 -202
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 1807 1841 3522 -5321 -8463 -5399 -8861 -8755 -9339 -6367 -5642
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 3787 3787 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 19379 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -3097 -6429 -3859 0 0 0 0 0 0 0 0
PALPH 1870 2058 -2000 -1529 -3186 0 0 0 0 0 0 0 0
PPBAS 1871 2059 5 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 6473 7282 7282 7282 4855 7282 7282 5826 6554 7282 7282
EMFLMT 1873 2061 120 120 0 120 120 120 120 120 120 120 120
POVC1 1877 2062 31823 32518 32368 32698 32740 32698 32732 32720 32720 32721 32706
POVC2 1878 2063 7334 3119 4997 873 345 873 452 596 596 583 777
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 27745 9277 14897 2590 1024 2590 1340 589 589 1326 2304
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 16384 0 0 0 0 0 0 0 0 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2838 2241 2339 1184 744 1184 852 564 564 847 1117
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 15000 15000 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 28519 1534 1538 455 1450 1367 3168 52 104 104 966
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 2334 24 0 0 0 0 0 0 0 0 0
DETQLM 1704 2111 2607 5722 5160 0 0 0 0 0 0 0 0
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 0 4054 2047 0 0 0 0 0 0 0 0
MFWKCE 1736 2128 6500 2000 2000 0 0 0 0 0 0 0 0
MFWKBL 1752 2129 1042 3075 3584 0 0 0 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 2581 0 5135 0 0 0 0 0 0 0 0
PHDLY2 1757 2134 15381 0 12820 0 0 0 0 0 0 0 0
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 140 0 0 0 0 0 0 0 0 0 0
POVC21 1785 2162 32667 0 0 0 0 0 0 0 0 0 0
POVC22 1786 2163 1264 0 0 0 0 0 0 0 0 0 0
POVCLMT2 1787 2164 21831 0 0 0 0 0 0 0 0 0 0
MAXCRT 1788 2165 365 85 85 85 245 245 365 25 45 45 165
- 610 -
Motor model 9000B 9000B/4N 15000C βM0.5 ΒM1

Motor specification 0413 0413-B811 0414 0115 0116
Linear Linear Linear
Motor ID No. 128 129 130 181 182
1808 2003 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000100 00000100 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000
1707 2013 00000110 00001010 00001010 00000000 00000000
1708 2014 00000110 00001010 00001010 00000000 00000000
1750 2210 00000000 00000000 00000100 00000000 00000000
1751 2211 00000000 00000000 00000000 00000010 00000010
2713 2300 10000000 10000000 10000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 6198 7416 2130 141 398
PK2 1853 2041 -19692 -17747 -8400 -511 -1137
PK3 1854 2042 -2660 -2660 -2663 -2415 -2388
PK1V 1855 2043 12 10 7 7 6
PK2V 1856 2044 -158 -141 -87 -59 -53
PK3V 1857 2045 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -7199 -8099 -13022 -6462 -7176
BLCMP 1860 2048 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 -12850 -12850
PVPA 1869 2057 0 0 0 0 -11530
PALPH 1870 2058 0 0 0 0 -1000
PPBAS 1871 2059 0 0 0 0 0
TQLIM 1872 2060 5917 4855 4855 6918 7282
EMFLMT 1873 2061 120 120 120 0 0
POVC1 1877 2062 32713 32737 32743 32674 32695
POVC2 1878 2063 687 388 313 1178 915
TGALMLV 1892 2064 4 4 4 4 4
POVCLMT 1893 2065 2038 1151 927 3497 2714
PK2VAUX 1894 2066 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0
AALPH 1967 2074 0 0 0 20480 20480
OSCTPL 1970 2077 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0
RTCURR 1979 2086 1050 789 708 1376 1212
TDPLD 1980 2087 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0
TRQCST 1998 2105 1823 2051 4656 42 89
LP24PA 1999 2106 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0
MGSTCM 1703 2110 0 0 0 30 30
DETQLM 1704 2111 0 0 0 10290 10290
AMRDML 1705 2112 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0
NINTCT 1735 2127 0 0 0 1009 1763
MFWKCE 1736 2128 0 0 0 0 0
MFWKBL 1752 2129 0 0 0 0 0
LP2GP 1753 2130 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0
PHDLY1 1756 2133 0 0 0 7690 11560
PHDLY2 1757 2134 0 0 0 12820 12880
DGCSMM 1782 2159 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0
POVC21 1785 2162 0 0 0 32767 32767
POVC22 1786 2163 0 0 0 16 12
POVCLMT2 1787 2164 0 0 0 3015 2340
MAXCRT 1788 2165 165 365 365 25 25
- 611 -
G.6 HRV2 CONTROL PARAMETERS FOR βM SERIES

MOTORS
December, 2002
The HRV2 control parameters for the βM series motors are given in the
table below.
90B0 series
NOTE
The parameters cannot be used with Series 9096.
- 612 -
Motor model βM0.2 βM0.3 βM0.4 βM0.5 βM1

Motor specification 0111 0112 0114 0115 0116
Motor ID No. 260 261 280 281 282
1808 2003 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000
1751 2211 00000010 00000010 00000010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 123 210 100 138 312
PK2 1853 2041 -510 -970 -430 -673 -1360
PK3 1854 2042 -1069 -1146 -2463 -1205 -1203
PK1V 1855 2043 4 4 7 7 6
PK2V 1856 2044 -36 -33 -61 -59 -53
PK3V 1857 2045 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -10638 -11550 -6249 -6462 -7176
BLCMP 1860 2048 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319
EMFCMP 1868 2056 0 0 -12850 -12850 -12850
PVPA 1869 2057 0 0 0 0 -15420
PALPH 1870 2058 0 0 0 0 -1000
PPBAS 1871 2059 0 0 0 0 0
TQLIM 1872 2060 7282 7282 5826 7282 7282
EMFLMT 1873 2061 0 0 0 0 0
POVC1 1877 2062 32725 32725 32640 32674 32695
POVC2 1878 2063 533 533 1603 1178 915
TGALMLV 1892 2064 4 4 4 4 4
POVCLMT 1893 2065 3163 3163 4759 3497 2714
PK2VAUX 1894 2066 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0
AALPH 1967 2074 20480 20480 20480 20480 20480
OSCTPL 1970 2077 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0
RTCURR 1979 2086 1929 1929 1605 1376 1212
TDPLD 1980 2087 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0
TRQCST 1998 2105 7 14 22 42 89
LP24PA 1999 2106 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0
MGSTCM 1703 2110 1 1 30 25 1556
DETQLM 1704 2111 7710 7700 10290 10290 10290
AMRDML 1705 2112 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0
NINTCT 1735 2127 379 852 400 504 881
MFWKCE 1736 2128 0 3000 0 0 1500
MFWKBL 1752 2129 0 3880 0 0 5135
LP2GP 1753 2130 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0
PHDLY1 1756 2133 7700 7695 7690 7690 15400
PHDLY2 1757 2134 12825 12840 12820 12820 12840
DGCSMM 1782 2159 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0
POVC21 1785 2162 0 0 32766 32767 32767
POVC22 1786 2163 0 0 22 16 12
POVCLMT2 1787 2164 0 0 4104 3015 2340
MAXCRT 1788 2165 4 4 25 25 25
- 613 -
H. DETAILS OF HIGH-SPEED AND
HIGH-PRECISION ADJUSTMENT APPENDIX B-65270EN/07
H DETAILS OF HIGH-SPEED AND

HIGH-PRECISION ADJUSTMENT
(1) Overview
Appendix H explains in detail the adjustment procedure described in
Section 3.3, "ADJUSTING PARAMETERS FOR HIGH-SPEED
AND HIGH-PRECISION MACHINING".
Appendix H, "DETAILS OF HIGH-SPEED AND HIGH-PRECISION

ADJUSTMENT", consists of the following sections:
(1) Overview ..................................................................................614

(2) Feed-forward coefficient adjustment
(using an arc of R10/F4000).....................................................615
(3) Velocity feed-forward coefficient adjustment
(example using a square figure with 1/4 arcs) ..........................618
(4) Adjustment of the parameters for arc radius based feedrate
clamping ...................................................................................622
(5) Adjustment of an allowable feedrate difference of the feedrate
difference based corner deceleration function ..........................624
(6) Frequency characteristic measurement method ........................626
(7) Adjustment of backlash acceleration ........................................627
- 614 -
H.DETAILS OF HIGH-SPEED AND
B-65270EN/07 APPENDIX HIGH-PRECISION ADJUSTMENT
(2) Feed-forward coefficient adjustment (using an arc of R10/F4000)
[Purpose of adjustment]
In a conventional position control loop where feed-forward
control is not exercised, a velocity command is output based on
(positional deviation) × (position loop gain). This means that the
machine moves only when there is a difference between the
specification of a command and the machine position. When the
position gain is 30 [1/s], for example, a feedrate of 10 m/min
generates a positional deviation of 5.56 mm. In linear feed, this
positional deviation does not cause a figure error. For an arc or
corner, however, this positional deviation causes a large figure
error.
A function for eliminating such a positional deviation is
feed-forward. Feed-forward converts the position command from
the CNC to a velocity command for velocity command
compensation. Feed-forward can reduce a positional deviation (to
almost 0, theoretically). Accordingly, feed-forward can reduce
arc and corner figure errors. However, the servo response is
improved, so that a shock can occur. To prevent a shock from
occurring, acc./dec. before interpolation must be used at the same
time.
[Guideline for adjustment value setting]

Theoretically, a feed-forward coefficient of 100% leads to a
positional deviation of 0, and eliminates figure errors. Actually,
however, there is a delay in velocity loop response. So, a value
slightly less than 100% produces a specified figure. Usually, a
value between 95% to 99% (settings of 9500 to 9900) is
optimum. As the default, use 9800.
First, adjust the feed-forward coefficient while viewing an arc
figure. (Set a velocity feed-forward coefficient of 50% before
starting adjustment.)
[Actual adjustment]
Create a program as indicated below for circular movement by
R10/F4000, and measure the path with SERVO GUIDE or SD.
G08P1 and G08P0 in the program are G codes for starting and
ending the advanced preview control mode in Series 16i and so
on, respectively. For a mode to be used, select the corresponding
G codes from Table H (a).
G91;
G08P1;
G17G02I-10.F4000.;
I-10.;
I-10.;
G08P0;
G04X3.;
M99;
- 615 -
Table H (a) Codes for starting and ending each mode

Start End
FS16i, 18i, 21i + Advanced preview control G08P1 G08P0
FS16i + High-precision contour control
FS16i + AI high-precision contour control
G05P10000 G05P0
FS16i + AI nano high-precision contour control
FS15i + Fine HPCC
FS30i + AI contour control I
FS30i + AI contour control II
FS16i + AI contour control
G05.1Q1 G05.1Q0
FS16i + AI nano-contour control
FS15i + Fine HPCC
FS21i + AI advanced preview control
In Fig. H (a), the feed-forward coefficient is insufficient, resulting in a

radius reduction of about 5 µm. In addition, the velocity loop gain is
low, so that swells and quadrant protrusions are observed. By
adjusting the feed-forward coefficient as shown in Fig. H (b), the arc
radius reduction can be reduced to nearly 0.
Swell
Quadrant
protrusion
Specified
arc
Fig. H (a) Feed-forward adjustment Fig. H (b) Feed-forward adjustment

Velocity loop gain: 100% Velocity loop gain: 100%
Advanced preview feed-forward coefficient: 95% Advanced preview feed-forward coefficient: 98%
FAD time constant: 24 ms (linear type) FAD time constant: 24 ms (linear type)
In the figures above, a low velocity loop gain is used for measurement.
By using an increased velocity loop gain, swells and quadrant
protrusions can be reduced (Fig. H (c)). Increase the velocity loop
gain to 70% to 80% of the limit. Adjust the feed-forward coefficient
finely, and apply quadrant protrusion compensation (backlash
acc./dec.) to reduce the quadrant protrusions and improve the
roundness (Fig. H (d)).
- 616 -
Fig. H (c) Effect of velocity loop gain Fig. H (d) Effect of velocity loop gain
- 617 -
(3) Velocity feed-forward coefficient adjustment (example using a square

figure with 1/4 arcs)
Feed-forward coefficient adjustment can reduce positional
deviation and figure errors. If the response of the velocity loop
for executing a velocity command is low, velocity control cannot
be exercised as specified where the specified acceleration varies
to a large extent, thus causing a figure error. The response of the
velocity loop can be improved by increasing the velocity loop
gain and by adjusting the velocity feed-forward coefficient.
Velocity feed-forward multiplies a specified rate of variation
(acceleration) by an appropriate coefficient for torque command
compensation. In the servo velocity loop (PI control), a
compensation torque occurs only when a difference (velocity
deviation) between a specified velocity and actual velocity
actually occurs. On the other hand, velocity feed-forward
performs torque command compensation according to an
acceleration value specified beforehand. So, a figure error that
occurs due to a velocity loop delay can be reduced.

The formula below is applicable. In actual adjustment, however,
make an adjustment starting with a velocity feed-forward
coefficient of 100.
(Velocity feed-forward coefficient) =
100 × (Motor rotor inertia + load inertia) / Motor rotor inertia
[Actual adjustment]
Make a velocity feed-forward coefficient adjustment by using a
square figure with four 1/4 arcs of a 5-mm radius. In this
adjustment, disable the velocity clamp function based on an arc
radius. (Disable the function, or in the example below, ensure
that a velocity equal to or greater than F4000 can be specified.)
G91;
G08P1;
G01X10.F4000;
Start, End 5 mm G02X5.Y-5.R5.;
G01Y-20.;
G02X-5.Y-5.R5.;
G01X-20.;
G02X-5.Y5.R5.;
5 mm G01Y20.;
G02X5.Y5.R5.;
G01X10.;
G08P0;
G04X3.;
M99;
Fig. H (e) Programmed figure
- 618 -
When the actual path is measured in a mode for displaying a reference

path, the actual path and reference path are plotted at the same time as
shown below:
Actual path
Specified path
Fig. H (f) Specified path and actual path
When advanced preview feed-forward is disabled, a figure error of

hundreds µm occurs as shown in Fig. H (f), and therefore can be
viewed even in the XY mode. However, if advanced preview
feed-forward is enabled for figure error reduction, it is difficult to
evaluate a figure error correctly unless the error is enlarged.
In such a case, use the figure comparison mode (contour mode) for
enlarging errors only for display (Ctrl O).
In addition, set an error display magnification with F3 (scale change).
For Fig. H (g), a display magnification of 100 is set.
Protrusion and cut due to

a delay on the Y-axis
Protrusion and cut due to a

delay on the X-axis
The figure display is 5 mm wide.

The error is 50 µm in size.
Fig. H (g) Velocity feed-forward adjustment Fig. H (h) Velocity feed-forward adjustment
Velocity feed-forward: 0% Velocity feed-forward: X100%
- 619 -
In Fig. H (g), the velocity feed-forward coefficient is not specified, so

that the movement along each axis delays where acceleration changes
to a large extent. As the result, a protrusion occurs at the joint of a
straight line with an arc, and a cut occurs at the joint of an arc with a
straight line. In Fig. H (h), a velocity feed-forward coefficient is set
for the X-axis only. The response of the X-axis has improved, so that
a figure improvement can be seen in the areas where acceleration
changes to a large extent along the X-axis.
In Fig. H (i), excessively large velocity feed-forward coefficients are

specified, so that the protrusions shown in Fig. H (g) have changed to
cuts, and the cuts have changed to protrusions. This means that
optimum velocity feed-forward coefficients exist and they are less
than the values of Fig. H (i). Fig. H (j) shows the result of adjustment
to the optimum values. Fig. H (k) enlarges the errors only for display.
Fig. H (i) Velocity feed-forward adjustment Fig. H (j) Velocity feed-forward adjustment
Velocity feed-forward: X200%, Y200% Velocity feed-forward: X120%, Y180%
- 620 -
When the enlarged range is viewed, it is seen that the machine is

vibrating in the arc areas. This vibration is caused by a low velocity
loop gain. To reduce this vibration, two methods are available. One
method increases the velocity loop gain. (This method cannot be used
when the velocity loop gain has already been increased to the
oscillation limit.) The other method decreases the feedrate in the arc
areas with the arc radius based feedrate clamp function as described in
Item H (4).
Machine vibration
caused by insufficient
velocity control
response is observed.
The figure display is 5 mm wide.

The error is 10 µm in size.
Fig. H (k) Velocity feed-forward adjustment
Swells in the arc areas can be reduced by increasing the velocity loop
gain (Fig. H (l)). However, figure errors that occur at the joints of
straight lines and arcs cannot be fully eliminated. Swells can be
additionally reduced by fine adjustment of the velocity feed-forward
coefficient or by using the arc radius based feedrate clamp function
described in Item H (6).
Figure errors in
this area cannot
be fully eliminated
by increasing the
velocity loop gain.
Swells can be
reduced by
increasing the
velocity loop gain.
Fig. H (l) Velocity feed-forward adjustment

Velocity loop gain: 300%
Advanced preview feed-forward coefficient: 99%
FAD time constant: 24 ms (linear type)
Velocity feed-forward: X120%, Y180%
- 621 -
(4) Adjustment of the parameters for arc radius based feedrate clamping
As mentioned above, velocity feed-forward coefficient
adjustment can improve a velocity loop response delay, thus
reducing figure errors in areas where specified acceleration
changes to a large extent. However, velocity feed-forward
coefficient adjustment alone cannot fully eliminate figure errors.
Moreover, if the rigidity of a machine itself is low, the machine
may vibrate due to a change in acceleration.
To reduce variation in specified acceleration in areas where

acceleration changes to a large extent, the specified feedrate in
the tangent direction is reduced. In part machining (advanced
preview control), the arc radius based feedrate clamp function
performs this feedrate reduction. By adjusting the parameter of
this function, an acceleration value in the normal direction
allowable with a machine can be found. As detailed below, such
an acceleration value can be used as a guideline for setting the
parameter for feedrate reduction by acceleration in high-precision
contour control (small successive blocks).
Feedrate F
Acceleration
in the normal
Radius R direction
In the above figure, let R be the radius of the arc, and F be the
feedrate. Then, the acceleration in the normal direction is F2/R.
The arc radius based feedrate clamp function specifies R and F as
its parameters to ensure that the acceleration in the normal
direction at a specified arc does not exceed the specified value.
For example, suppose that when R = 5 mm and F = 4000 mm/min are

specified as the parameters of the arc radius based feedrate clamp
function, the acceleration in the normal direction at the arc is:
F2/R = (4000/60)2/5 = 889 mm/sec2
When using the high-precision contour control function, set about the
same value as this acceleration as the parameter for feedrate reduction
function based on acceleration in small blocks. In the example above,
if a cutting feedrate of F4000 (mm/min) is set, the time required to
reach this feedrate is calculated as follows:
4000/60/889×1000 = 75 msec
- 622 -
When the feedrate at an arc is reduced using the arc radius based
feedrate clamp function, figure precision improves. However, a longer
machining time is required as a side effect. Fig. H (m) shows a tangent
feedrate and processing time when the arc radius based feedrate clamp
function is not used with the adjustment program used in (5) and later.
Fig. H (m) indicates that the tangent feedrate remains to be F4000. On
the other hand, when feedrate reduction to F3000 at R5 mm is
specified with the arc radius based feedrate clamp function, the
tangent feedrate is reduced to F3000 at corners as shown in Fig. H (n),
but the machining time has increased by 200 msec.
A cceleration of
Tangent
acceleration/
feedrate deceleration before
interpolation
T angent
feedrate
Feedrate reduction to
F3000
1900 m sec
X-axis 2100 m sec
position
Fig. H (m) When the arc radius based feedrate clamp Fig. H (n) When the arc radius based feedrate clamp
function is not used function is used

Empirically, the values below are adequate. For the parameter
numbers, refer to the parameter manual of each CNC.
Standard: F3060 for R5 (527 mm/sec2)
Speed priority I: F5150 for R5 (1473 mm/sec2)
Speed priority II: F7275 for R5 (2940 mm/sec2)
[Actual adjustment]
Fig. H (o) shows the results of setting R5 mm and F3000 with the
arc radius based feedrate clamp function for Fig. H (k). Fig. H
(o) indicates that the figure errors at the entries and exits of the
arc areas have been reduced.
The figure errors

at the entries and
exits of each arc
area have been
The figure display is 5 m m wide. reduced.
The error is 10 µ m in size.
Fig. H (o) Arc radius based feedrate clamping
- 623 -
(5) Adjustment of an allowable feedrate difference of the feedrate difference

based corner deceleration function
In the program shown in Fig. H (p), the feedrate along each axis
changes to a great extent at each block joint. With a
high-precision high-speed system, the CNC reads programmed
figures beforehand. If the feedrate along each axis changes at a
block joint, such a system can decrease the feedrate by a
parameter-specified allowable feedrate difference to reduce a
shock and figure error at the block joint. Acc./dec. is performed
based on the time constant for acc./dec. before interpolation. A
more reduced corner feedrate makes a figure error improvement
to a greater extent, but requires a longer machining time. Set a
reduced corner feedrate to a highest possible value as long as an
allowable figure error is obtained.
[Guideline for setting]

For the parameter number, refer to the parameter manual of each
CNC.
Standard: F400 for R5
Speed priority I: F500 for R5
Speed priority II: F1000 for R5
[Actual adjustment procedure]

Execute the following program, and measure the actual path.
G91;
Start and end point
G08P1;
Corner 4
G01X10.F4000;
G01Y-20.;
Corner 1 G01X-20.;
G01Y20.;
G01X10.;
G08P0;
G04X3.;
Corner 2 M99;
Corner 3
Fig. H (p) Programmed figure
The XY mode (Ctrl-X) is used for drawing. To observe an overshoot

along an axis to be stopped, the figure is enlarged in the direction of
the axis to be stopped. Corner 1 and corner 3 in Fig. H (p) are
enlarged in the X-axis direction, and corner 2 and corner 4 are
enlarged in the Y-axis direction. In the examples below, corner 1 is
displayed using 0.01 mm/div in the X-axis direction and 0.1 mm/div
in the Y-axis direction.
In Fig. H (q) where a reduced corner feedrate of F1000 is set, an
overshoot of 10 µm or more has occurred. In Fig. H (r), however, the
overshoot is reduced to about 3 µm.
- 624 -
If an overshoot cannot be removed by setting a reduced corner

feedrate close to 0, the acceleration of acc./dec. before interpolation
may be too large. In such a case, set a longer time for acc./dec. before
interpolation. (In this case, a longer machining time results.)
Fig. H (s) shows the feedrate along the X-axis and Y-axis (corner 1)
when the corner deceleration function is used.
O vershoot
0.01 m m
Fig. H (q) Reduced corner feedrate F1000 Fig. H (r) Reduced corner feedrate F300
Feedrate along the X-axis
with the time constant for fine
Reduced corner feedrate acceleration/deceleration or
acceleration/deceleration
after interpolation
Feedrate along the Y-axis
at the acceleration of
acceleration/deceleration
before interpolation Specified feedrate
Fig. H (s) Time and feedrate relationship for reduced corner feedrate F1000
- 625 -
(6) Frequency characteristic measurement method

To measure the frequency characteristic, follow this procedure.
NOTE
1 The method of frequency characteristics
measurement using SERVO GUIDE is described
below. For the method using the servo check
board, see Appendix I.5.
2 For frequency characteristics measurement using
SERVO GUIDE, CNC parameter setting is
basically not required.
1 On the graph window menu, select [Tool(T)] → [Frequency

Response] → [Measure...] to display the "Frequency
measurement" dialog box.
2 Select an axis on which you want to measure frequency

characteristics, and click the [Start] button. The axis is
automatically vibrated, and frequency characteristics (board line
chart) are displayed.
3 Click the [Detail] button. It becomes possible to specify options.

Make option settings as required.
4 To re-draw, select [Draw Bode diagram] from [Frequency

Response] on the [Tool(T)] menu.
- 626 -
(7) Adjustment of backlash acceleration

NOTE
The examples given below show the adjustment of
backlash acceleration in the Series 30i and 16i.
Even with other CNCs, the adjustment procedure is
the same. When using the Series 15i, however,
replace parameter Nos. according to the table
given below.
(a) Backlash acceleration function

A simple figure as shown below is formed by the compensation value
of backlash acceleration. The acceleration compensation value is
added to the velocity command to help inversion of the velocity
integral gain when the motor is reversed. This effect can reduce the
path error in the reverse operation.
(Standard backlash acceleration)

Backlash acceleration
No.2048
No.2071
Velocity command
Basically, the above two parameters are considered. Parameter No.

2071 is the backlash acceleration time, and its recommended value is
20. Normally, this value need not be adjusted. Parameter No. 2048 is
the backlash acceleration amount. In the initial adjustment stage, set
100 in this parameter. Adjust this value while observing the arc figure.
(b) Setting initial parameters for backlash acceleration

Before starting backlash acceleration adjustment, set the following
initial parameters:
[Basic parameters for backlash acceleration]

Parameter No.
Recommended value Description
15i 30i,16i,etc.
1851 1851 1 or greater Backlash compensation
1808#5 2003 #5 1 Enables backlash acceleration function
1884#0 2006 #0 0/1 0: Semi-closed loop, 1: Full-closed loop
1953#7 2009 #7 1 Stop of backlash acceleration
2611#7 2223 #7 1 Enables backlash acceleration during cutting only.
1957#6 2015 #6 0 Disables the two-stage backlash acceleration function.
5 (1µm detection)
1975 2082 Backlash acceleration stop distance (in detection unit)
50 (0.1µm detection)
1964 2071 20 Backlash acceleration time
- 627 -
These parameters can be set in the parameter window of SERVO

GUIDE.
(c) Adjusting backlash acceleration

The following figure shows an arc figure before servo adjustment.
Quadrant protrusions of about 4 µm appear on the X- and Y-axes.
The figure below shows the result of a backlash acceleration

adjustment made according to the parameter settings in item (b). By
setting recommended values for backlash acceleration, quadrant
protrusions can be suppressed.
- 628 -
(c)-1 Determining the end of adjustment

First, it is necessary to understand when the backlash acceleration
adjustment is ended. The figure below shows the result of an
adjustment made by setting parameter No. 2048 to 200. An undercut
occurs at the reverse points. Undercuts damage the surface of the
machined workpiece, so they must be avoided. Therefore, it is
necessary to end the adjustment of parameter No. 2048 just when no
undercut occurs.
By enlarging the positional deviation at a reverse point, the generation

of an undercut can be determined easily. Pressing z widens the figure
while pressing Z shrinks the width. Pressing u decreases one grid size
while pressing d increases the grid size.
When z and u are pressed, a figure as shown below is obtained:
Undercut
Undercut
- 629 -
(c)-2 Effect of gain adjustment

According to the description in item (c)-3 - (1), the final value of
parameter No. 2048 must be determined to be 100. However, small
protrusions are still left at the reverse points. This is because the gain
adjustment is insufficient in this example. The power to suppress the
position gain and velocity loop gain protrusions is strong and stable.
Therefore, it is necessary to make gain adjustments thoroughly before
the backlash acceleration adjustment.
The figure shown below is the result of the gain adjustment, where
backlash acceleration is not used. Even when backlash acceleration is
not used, protrusions are almost eliminated. Therefore, the importance
of gain adjustment can be understood.
(Adjustment items)
• Application of high-speed HRV current control
• Velocity loop gain: 600% (200% in the above example)
• Position gain: 100/s (30/s in the above example)
- 630 -
After a thorough gain adjustment, backlash acceleration can be

adjusted easily. The figure shown below is the result obtained after the
initial parameters of backlash acceleration listed in item (c)-3 - (2) are
set. Thanks to the effect of the gain adjustment and a little backlash
acceleration, protrusions are completely eliminated.
As indicated by this figure, the most important item to eliminate

quadrant protrusions is gain adjustment. If gain adjustment is made
successfully, backlash acceleration can be adjusted easily. Therefore,
backlash acceleration does not play the leading role for suppressing
quadrant protrusions.
- 631 -
(c)-3 Override function

The two figures shown below indicate the difference by feedrate. In
this example, the same acceleration amount (parameter No. 2048 is set
to 100) is used, but the results are completely reversed. This example
shows that a low feedrate requires a small backlash acceleration
amount and that a high feedrate requires a large acceleration amount.
This means that the backlash acceleration amount must be changed
according to the feedrate.
An actually optimum acceleration amount is almost proportional to the
acceleration. Therefore, an override function is required to change the
acceleration amount according to the acceleration.
F500mm/min F5000mm/min
For F500 mm/min, 100 set in parameter For F5000 mm/min, 100 set in parameter No.
No. 2048 is too large. 2048 is too small.
* In this chapter, PG is assumed to be 50, and VG is assumed to be 400%.
The override function has two parameters. Parameter No. 2114

specifies an override coefficient, and parameter No. 2338 specifies a
limit. These parameters may be adjusted easily if steps (1) through (3)
explained below are followed.
[Parameters for the override function]

Parameter No.
Standard value Description
15i 30i,16i,etc.
1725 2114 0 Backlash acceleration override coefficient
2751 2338 0 acklash acceleration limit
Backlash acceleration amount
No.2338
No.2114
No.2048
Acceleration
- 632 -
(1) Determining parameter No. 2048

To determine parameter No. 2048, an adjustment must be made
at low feedrate. This example assumes a feedrate of F500
mm/min and a radius of 10 mm. Adjust an optimum value at a
low feedrate, and set it in parameter No. 2048. The figure below
shows the result of setting 30 in parameter No. 2048. Here, this
value is set in parameter No. 2048.

Parameter No. 2114 must be set after the adjustment of parameter
No. 2048. About a half of the maximum cutting feedrate is used
to determine the value to be set in parameter No. 2114. In this
example, F2500 mm/min is used. By increasing the value in
parameter No. 2114, determine an optimum value that does not
cause undercuts. Increasing the value in parameter No. 2114
increases the actual acceleration amount.
The following figure shows the result of the adjustment of

parameter No. 2114. Quadrant protrusions can be suppressed
satisfactory.
- 633 -

Finally, set parameter No.2338. With an override coefficient
determined using a middle feedrate, a large acceleration amount
is output when the feedrate is set to a high feedrate. For this
reason, the acceleration amount must be limited for high feedrate.
In this example, F5000 mm/min is used.
The following shows the result of the adjustment of parameter

No. 2338 at high speed. Quadrant protrusions are suppressed
well.
- 634 -
(d) Acceleration amount for each direction

There may be difference in size between the right and left quadrant
protrusions or between the top and bottom quadrant protrusions. In
such a case, an acceleration amount must be set separately.
If parameter No. 2094 is not 0, parameter No. 2094 is used for the left
and bottom reverse points. Parameter No. 2340 is used as the override
coefficient for parameter No. 2094, and parameter No. 2341 is used as
the limit for parameter No. 2094.
[Parameters of acceleration amount for each direction]

Parameter No.
15i 30i,16i,etc.
1725 2114 0 Backlash acceleration override coefficient
2751 2338 0 Backlash acceleration limit
1987 2094 0 Backlash acceleration amount (- to +)
2753 2340 0 Backlash acceleration override coefficient (- to +)
2754 2341 0 Backlash acceleration limit (- to +)
No.2048
No.2114
No.2338
No.2094
No.2340
No.2341
- 635 -
(e) Disabling backlash acceleration after stop

The optimum acceleration amount after a long stop may slightly be
different from that at the time of adjustment using an arc. This
phenomenon is due to the difference in friction, backlash, and
machine torsion in the stopped state. The figure given below shows
the bad effect of backlash acceleration, where a 3-µm overshoot is
generated at the time of 10-µm step movement. As a solution to this
problem, the following servo software can disable backlash
acceleration after a stop:

[Parameters for the function for disabling backlash acceleration after a

stop]
Parameter No.
15i 30i,16i,etc.
1883#7 2005#7 1 Static friction compensation function
2696#7 2283#7 1 Function for disabling backlash acceleration after a stop
1966 2073 5 Judgment parameter for stop state (ITP)
1964 2071 0 Static friction compensation function enable time
1965 2072 0 Static friction compensation value
(*) This function uses the parameters for the static friction
compensation function.
When this function is disabled When this function is enabled
Overshoot present Overshoot not present
10µm 10µm
- 636 -
I.SERVO CHECK BOARD
B-65270EN/07 APPENDIX OPERATING PROCEDURE
I SERVO CHECK BOARD OPERATING

PROCEDURE
Appendix I, "SERVO CHECK BOARD OPERATING
PROCEDURE", consists of the following sections:
I.1 METHOD OF USING THE SERVO CHECK BOARD..........638

I.2 ADJUSTING UNEXPECTED DISTURBANCE TORQUE
DETECTION WITH THE CHECK BOARD ..........................651
I.3 ADJUSTING LINEAR MOTOR AMR OFFSET WITH THE
CHECK BOARD (INCREMENTAL TYPE)...........................652
I.4 ADJUSTING SMOOTHING COMPENSATION FOR A
LINEAR MOTOR WITH THE CHECK BOARD...................655
I.5 MEASURING FREQUENCY CHARACTERISTICS WITH
THE CHECK BOARD .............................................................661
- 637 -
I. SERVO CHECK BOARD
OPERATING PROCEDURE APPENDIX B-65270EN/07
I.1 METHOD OF USING THE SERVO CHECK BOARD
(1) Overview
The servo check board enables digital control values used in a digital
servo section to be observed from the outside. The digital control
values can be observed in either analog or digital form. Analog
outputs can be observed directly with an oscilloscope, and digital
outputs can be observed with a personal computer.
(2) Servo check board configuration

The following table lists the signals that can be observed with the
servo check board, and the number of supported axes.
Table I.1 (a) Servo check board specification

Number of Number of
Name Specification Output interface supported output
axes channels
A A06B-6057-H630 Analog and digital 8 4 (optional)
B A06B-6057-H620 Digital only 4 4 (optional) (*)
C A06B-6057-H602 Analog only 2 8 (fixed) (*)
* Servo check board A (one-piece analog/digital type) is
upward-compatible, that is, can be replaced, with digital check
board B and analog check board C.
The method for connecting the servo check board with a CNC varies
with the type of the CNC.
The method may also vary with the name of a connectable terminal.
The following table lists the ordering information for adapters and
cables required to connect the check board.
Table I.1 (b) Adapters and cables required to connect the servo check
board to each CNC
Required adapters and Ordering
CNC
cables information
Series 16i, 18i, 20i, 21i, Dedicated i-B adapter board A02B-0281-K822
0i-B + dedicated i-B cable
Straight cable A06B-6050-K872
Series 15i, Power Mate i Adapter board A02B-0236-K822
+ dedicated i series cable
Straight cable A06B-6050-K872
NOTE
With Series 30i, 31i, 32i, 0i -C, or 0i Mate-C, the
servo check board cannot be connected.
- 638 -
I.SERVO CHECK BOARD
(3) Servo check board connection
CAUTION
When connecting the servo check board to an NC,
keep the NC power supply switched off. When the
servo check board is directly connected not via an
adapter board, the circuitry of both of the CNC and
check board can be damaged.
(a) Connection between check board A (one-piece analog/digital

type) and each CNC
CNI1
CNI4 CNI3
5VIN
CNI2
CNS1
TM1
5VEX
GND
LSI ERROR
AXIS DATA AXIS DATA AXIS DATA AXIS DATA
CNA2
CNB1
RECV RECV RECV RECV

CH1 CH2 CH3 CH4
+
CNB2
PC ACCESS ← →
ANALOG
ERROR
CH1 CH2 CH3 CH4
−
CNA1
GND CH1CH2CH3 CH4 GND
ANALOG OUTPUT
Fig. I.1 (a) Connector layout on servo check board A (A06B-6057-H630)
Series 16i, 18i, 20i, 21i, 0i-B

* A dedicated i-B cable is used to connect the CA69 connector of
the CNC with the adapter.
Dedicated i-B adapter board + dedicated i-B cable
A02B-0281-K822
CNC
Straight cable
Dedicated i-B A06B-6050-K872
cable CNI3
DC-DC
TESTA First to
CA69 fourth axes
CNI4
DC-DC
TESTB Fifth to
eighth axes
Servo check board

A06B-6057-H630
Second CPU Loader control
CA69 CA69
- 639 -
Series 15i, Power Mate i

* A dedicated cable is used to connect the CA54 connector of the
CNC with the adapter.
Adapter board + dedicated i series cable
A02B-0236-K822
CNC
Straight cable
Dedicated i series A06B-6050-K872
cable CNI3
TESTA First to
CA54 fourth axes
CNI4
TESTB Fifth to
eighth axes
Servo check board

A06B-6057-H630
Second CPU Loader control
CA54 CA54
(b) Connection between servo check board B (interface board

supporting automatic adjustment) and each CNC
CNB1 CNB2 CNB3 CNB4 CNS1
Outputs for PIO-48W PC-Card Output to Analog Spindle

Input from JA8A
CN13
CNA1
CN12
CN11
Data Type Setting
Axis4 Axis3 Axis2 Axis1
A16B-2300-0170 1001 1000 1001 1000
1:High 0:Low
Fig. I.1 (b) Connector layout on servo check board B (A06B-6057-H620)
* The connection method for servo check board C is the same as

for servo check board A
A straight cable is used to connect the dedicated adapter board
with the check board, and TESTA or TESTB of the dedicated
adapter board is connected to CBI3 on the check board. In this
case, the data of axes 1 to 4 and the data of axes 5 to 8 cannot be
observed at the same time.
- 640 -
I.SERVO CHECK BOARD
(c) Connection between servo check board C (analog check board)

and each CNC
GNDTSALTSAM CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 GND
NOTE
Install a jumper
pin on the 5 MHz
side at S1 (clock)
on the check
board.
Rotary switch SW
Do not use check
CN2
2.5 MHz
pins TSAL and
CN1
55MHz
S1
RS1 TSAM.
A16B-1600-0320
Fig. I.1 (c) Connector layout on servo check board C (A06B-6057-H602)
* The connection method for servo check board B is the same as

for servo check board A
A reverse-insertion protection cable is used to connect the
dedicated adapter board with the check board, and one of TEST0
through TEST3 of the dedicated adapter board is connected to
the connector CN2 on the check board.
(4) Selecting signals for observation

(a) Servo check board A (one-piece analog/digital type)
On servo check board A, a pair of two 7-segment LED digits is
used to select the axis and data type for signals to be observed.
Set the AXIS digit with the axis number (1 to 8) set in parameter
No. 1023.
Also set the DATA digit with the type of data to be observed (the
table below).
Data is not output for an axis unless the RECV LED lights for
that axis.
DATA Data type
0 Velocity command (VCMD) AXIS DATA
1 Torque command (TCMD) or estimated load torque
2 Speed (SPEED)
4 Position (POS)
5 Automatic adjustment data
6 Automatic adjustment data 2 RECV
7 Servo-spindle synchronization error (updated every 8 ms)
* DATA7 is output only when the CNC is the Power Mate i.
- 641 -
(b) Servo check board B (digital type)

Set the DIP switches as explained below.
A06B-6057-H620
Set DIP switches 1 and
CNB1 CNB2 CNB3 CNB4 CNS1
Outputs for PIO-48W PC-Card Output to Analog Spindle
0 according to the
Input from JA8A
CN13
DIP switch
directions printed on
CNA1
CN12
the printed-circuit
CN11
board.
Data Type Setting
A16B-2300-0170 1001 1000 1001 1000
1: High 0: Low
Example of setting with the DIP

switches on your side as shown at
the right.
1 0 0 1 1 0 0 0 1 0 0 1 1 0 0 0
8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1
1
SW301
SW101
ON ON
0
0
Data for the third and fourth Data for the first and second
axis is selected. axis is selected.
* The terms "L axis" and "M axis" refer to an axis assigned an odd
number specified in parameter No. 1023 and an axis assigned an
even number that follows directly that odd number, respectively.
Data type L axis M axis Data type L axis M axis

Velocity command O 1 Position O 1 O O
(VCMD) OOOOOO O 0 (POS) OOO OO 0
Torque command/ O OO 1 O O O OO 1
Adjustment
estimated load O O O O O 0 O O O 0
O O O 1 OO OO O 1
Speed (SPEED) Adjustment 2
O OOO O 0 OO O 0
(c) Servo check board C (analog type)

Output data is permanently assigned to each check pin as listed
below.
The rotary switch on the printed-circuit board is kept at 0 for
usual use.
* The terms "L axis" and "M axis" refer to an axis assigned an odd
number specified in parameter No. 1023 and an axis assigned an
even number that follows directly that odd number, respectively.
Check pin
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
L axis M axis
0 - -
SPEED SPEED
Rotary switch
L axis M axis
L axis M axis
1 L axis L axis M axis M axis adjust- adjust-
POS POS
VCMD TCMD VCMD TCMD ment ment
L axis M axis
2 adjust- adjust- - -
ment 2 ment 2
- 642 -
I.SERVO CHECK BOARD
(5) VCMD signal

When the feed-forward function is not used, the VCMD signal
conveys a velocity command.
With this signal, it is possible to measure very slight vibration in the
motor and its motion irregularity.
When the feed-forward function is used, the VCMD signal represents
a positional deviation rather than a velocity command. So the signal
can be used to measure vibration in the motor and irregularity in the
feed distance of the tool driven by the motor.
The signal conversion type for the VCMD signal can be switched
using parameters.
This switching is used, if the signal waveform is hard to observe
because of the VCMD signal being reciprocating within ±5 V.
#7 #6 #5 #4 #3 #2 #1 #0
No. 1956 (FS15i) VCM2 VCM1
No. 2012 (FS16i)
Parameters for rotary motor

VCM2 VCM1 Specified rotation speed/5 V
0 0 0.9155 min-1
0 1 14 min-1
1 0 234 min-1
1 1 3750 min-1
Parameters for linear motor (Incremental type : P=signal pitch[µm])

(Absolute type : P= resolution [µm] × 512)
VCM2 VCM1 Specified velocity/5 V
0 0 0.00375 × P m/min
0 1 0.006 × P m/min
1 0 0.96 × P m/min
1 1 15.36 × P m/min
Using an oscilloscope to see the movement of the entire signal in DC

mode, then its magnified image in AC mode enables you to check
very slight vibration in the motor and its motion irregularity.
Enlarged
DC mode AC mode
Fig. I.1 (d) Waveform of the VCMD signal
- 643 -
The following table lists the number of positional deviation pulses for
a VCMD voltage of 5 V.
Table I.1 (c) Number of positional deviation pulses for a VCMD voltage of
5 V for semi-closed loop
Number of positional deviation pulses for a VCMD
VCM2 VCM1
voltage of 5 V
0 0 15,258 × FFG/Kp
0 1 244,133 × FFG/Kp
1 0 3,906,133 × FFG/Kp
1 1 62,498,133 × FFG/Kp
Kp: Position gain (s-1)
FFG: Flexible feed gear (numerator/denominator)
Table I.1 (d) Number of positional deviation pulses for a VCMD voltage of
5 V for full-closed loop
VCM2 VCM1
voltage of 5 V
0.0153 × (number of positional feedback occurrences per
0 0
motor revolution)/Kp
0 1
1 0
62.5 × (number of positional feedback occurrences per motor
1 1
revolution)/Kp
Table I (e) Number of positional deviation pulses for a VCMD voltage of 5

V when a linear motor is in use
VCM2 VCM1
voltage of 5 V
0 0 32,000×FFG/Kp
0 1 512,000×FFG/Kp
1 0 8,192,000×FFG/Kp
1 1 131,072,000×FFG/Kp
FFG: Flexible feed gear (numerator/denominator)
(Example)
Assume the following conditions:
Position gain = 30 (s-1), semi-closed loop, detection unit of 1
µm/pulse, flexible feed gear = 1/100,
VCM2 = 0, VCM1 = 1 (VCMD waveform signal calculation
parameters)
If a waveform with E = 0.3 V and I/f = 20 ms is observed:
Number of positional deviation pulses for a VCMD voltage of 5

V = 244133/100/30 = 81 pulses
Table vibration = 81 × 0.3/5 = 4.88 µm

Vibration frequency = 50 Hz
- 644 -
I.SERVO CHECK BOARD
(6) TCMD signal

The TCMD signal conveys a torque command for the motor.
When a motor is running at high speed, its actual currents (IR and IS)
may differ from the rating because of back electromotive force.
The output voltage of the signal becomes 4.44 V at maximum current.
A higher signal voltage may be observed in a motor in which the
actual current limit function is enabled, however.
Table I.1 (f) TCMD waveform conversion
Maximum current Ap/V Applicable servo motor
4Ap 0.9 βiS0.2/5000, βiS0.3/5000
αiS2/5000HV, αiS2/6000HV, αiS4/5000HV,
10Ap 2.3
βiS2/4000HV, βiS4/4000HV, βiS8/3000HV
αiS2/5000, αiS2/6000, αiS4/5000, αiF1/5000, αiF2/5000, αiF4/4000HV, αiF8/3000HV,
αC4/3000i, αC8/2000i, αC12/2000i, βiS0.4/5000, βiS0.5/5000, βiS0.5/6000, βiS1/5000,
20Ap 4.5
βiS1/6000, βiS2/4000, βiS4/4000, βiS8/3000, βiS12/2000, βiS22/1500, βiS12/3000HV,
βiS22/2000HV, LiS300A1/4, LiS1500B1/4(400V), DiS22/600, DiS22/600(400V)
αiF4/4000, αiF8/3000, αiS8/4000HV, αiS8/6000HV, αiS12/4000HV,
αiF12/3000HV, αiF22/3000HV, αC22/2000i, βiS2/4000(40A-driven),
40Ap 9 βiS4/4000(40A-driven), βiS8/3000(40A-driven), βiS12/2000(40A-driven),
βiS22/1500(40A-driven), βiS12/3000, βiS22/2000, LiS600A1/4, LiS900A1/4,
LiS1500B1/4, LiS3000B2/2 , LiS4500B2/2HV, DiS85/400, DiS85/400(400V), DiS85/1000
αiS8/4000, αiS8/6000, αiS12/4000, αiF12/3000,
αiF22/3000, αiS22/4000HV, αiS30/4000HV, αiS40/4000HV, αC30/1500i, LiS3000B2/4,
80Ap 18 LiS4500B2/2, LiS6000B2/2, LiS6000B2/2HV, LiS7500B2/2HV, LiS3300C1/2,
LiS11000C2/2HV, DiS110/300, DiS110/300(400V), DiS260/300, DiS260/300(400V),
DiS370/300, DiS370/300(400V), DiS110/1000
αiS22/4000, αiS30/4000, αiS40/4000, αiF30/3000, αiF40/3000, αiF40/3000 FAN,
160Ap 36 LiS6000B2/4, LiS7500B2/2, LiS9000B2/2, LiS9000C2/2, LiS11000C2/2, LiS10000C3/2,
DiS260/600, DiS1200/250, DiS1500/200, DiS2100/150, DiS3000/150, DiS260/1000
αiS50/3000HV, αiS50/3000HV FAN, αiS100/2500HV, αiS100/2500HV FAN,
αiS200/2500HV, αiS200/2500HV FAN, LiS7500B2/2(400V), LiS9000B2/2(400V),
180Ap 41 LiS9000C2/2(400V), LiS11000C2/2(400V), LiS15000C2/3HV, LiS10000C3/2(400V),
DiS260/600(400V), DiS1200/250(400V), DiS1500/200(400V), DiS2100/150(400V),
DiS3000/150(400V)
αiS50/3000, αiS50/3000FAN, αiS100/2500, αiS200/2500, αiS300/2000, αiS500/2000,
360Ap 82 αiS300/2000HV, αiS500/2000HV, αiS1000/2000HV, LiS7500B2/4, LiS9000B2/4,
LiS15000C2/2, LiS15000C2/3, LiS17000C3/2
1440Ap 328 αiS2000/2000HV
* Effective current (RMS) = TCMD signal output (Ap) × 0.71
- 645 -
(7) SPEED signal

The SPEED signal conveys the rotation speed of the motor.
Signal conversion 3750 min-1/5 V
Linear motor (Incremental : P= signal pitch[µm])

(Absolute : P= resolution [µm] × 512)
Signal conversion 15.36 × P (m/min)/5 V
When the SPEED signal is latched at 5 V, check whether the

following parameter is set with a value.
No. 1726 (FS15i) Must be kept at 0.

No. 2115 (FS16i)
* Setting this parameter with a value other than 0 disables the
SPEED signal output.
(8) Changing the check board output magnification for the TCMD and SPEED
signals
Conventionally, the measured waveforms of the TCMD signal (torque
command) and SPEED signal (actual feedrate) were folded at 5 V in
some cases and difficult to read if the torque command value is large
or the actual feedrate exceeds 3750 min-1, because the ranges of these
signals were fixed when output to the check board. An improvement
was made so that the output ranges of measured waveforms can be
changed according to parameter settings.

Series 90B0/N(14) and subsequent editions
#7 #6 #5 #4 #3 #2 #1 #0
No. 2613 (FS15i) TSA05 TCMD05
No. 2225 (FS16i)
TCMD05(#1) The voltage of the TCMD signal output to the check board is:
0 : Unchanged (default)
1 : Halved
* The actual output voltage is affected by the following function
bit (TCMD4X).
TSA05(#2) The voltage of the SPEED signal output to the check board is:
0 : Unchanged (3750 min-1/5 V) (default)
1 : Halved (7500 min-1/5 V)
Conventionally, there has been the following function bit (TCMD4X)

for multiplying the output voltage weight of TCMD by 4. This bit can
be used along with the newly added function bit (TCMD05).
- 646 -
I.SERVO CHECK BOARD
#7 #6 #5 #4 #3 #2 #1 #0
No. 1743 (FS15i) TCMD4X
No. 2203 (FS16i)
TCMD4X(#5) The voltage of the TCMD signal output to the check board is:
0 : Unchanged (default)
1 : Multiplied by 4
Using these function bits changes the output ranges of the TCMD and
SPEED signals as listed in Table I (g) and Table I (h).
- TCMD signal output range

Table I.1 (g) TCMD signal conversion (improved)
TCMD4X TCMD05 TCMD value/4.4 V Remark
0 1 Amplifier maximum current × 2 (A)
0 0 Amplifier maximum current (A) Conventional mode
1 1 Amplifier maximum current/2 (A)
1 0 Amplifier maximum current/4 (A) × 4 mode
Example:
Relationships between the output voltage and TCMD value [A]
when an 80-A amplifier is used
TCMD4X TCMD05 TCMD value/4.4 V
0 1 160 [A]
0 0 80 [A]
1 1 40 [A]
1 0 20 [A]
- SPEED signal output range

Table I.1 (h) SPEED signal conversion (improved)
Actual feedrate per 5 V Actual feedrate per 5 V
TSA05 Remark
Rotary motor Linear motor
Conventional
0 3750 [min-1] 15.36 × P [min-1]
mode
1 7500 [min-1] 30.72 × P [min-1]
* Letter P in the linear motor column has a different meaning
depending on the type of the scale.
• When the FANUC high-resolution serial conversion circuit is

used
(Incremental scale) → P = signal pitch[µm]
• When a scale that matches the FANUC serial interface is used.

(Absolute scale) → P = resolution [µm] × 512
- 647 -
(9) Acquiring signals using a personal computer

Servo check boards A and B, listed in Table I (a), have a digital output
interface. Using the servo adjustment software (SD) enables them to
collect servo data such as position and speed through the interface into
a personal computer.
(a) Connection between a servo check board and a personal
computer (IBM PC/AT compatible)
Connect servo check board connector CNA1 to the printer port of
a personal computer. The printer port must support bidirectional
communication mode. (Measurement is impossible in ECP
mode.)
Windows does not support the servo adjustment software (SD).
Use it in full-screen mode or MS-DOS mode.
(b) Basic operating instructions

<1> Enter "SD INIT" at a DOS prompt. The software starts with
all its states initialized, and its main screen appears (if the
name of the software's executable file is "SD.EXE").
The main screen lets you measure and view data.
Entering "CTRL + letter" switches the drawing mode.
Select a drawing mode suitable for the data to be observed.
(Pressing the ? key displays a list of the available drawing
modes.)
Drawing mode examples:
CTRL + X: XY mode (XY display)
CTRL + T: XTYT mode (time axis display)
Parameter setting System setting
F10 F10
F5 F9
F1: Measure data

F2: Change the number of measurement points
F3: Change the display range
F4: Edit comments
Main screen
F7: Save data
F8: Read data
F10: End
Fig. I.1 (e) Servo adjustment software basic configuration and key manipulation
- 648 -
I.SERVO CHECK BOARD
<2> To change the type of data to be measured and the unit of

conversion for it, press the F9 key on the main screen to display
the system setting screen.
Use numeric keys 0 to

3 to specify a signal to
be observed on each
measurement channel
and a unit conversion
for it.
Fig. I.1 (f) System setting screen
Data output on CH1 to CH4 of the check board corresponds to

channels 0 to 3 on the SD software. To change the setting, press
numeric key 0 to 3. Select a data type (0: position, 1: velocity
command, 2: torque command, 3: rotation speed) from the display at
the bottom of the screen, then specify the unit of conversion for the
data.
Conversion values (except for position data) can be set up according
to descriptions in (5) to (8).
Table I.1 (i) Meaning of measurement data conversion values and example setting
Display at
Meaning of conversion
Type the bottom Example Input value
values
of the screen
POS 1 pulse = X? Detection unit (in mm units) 1 µm 0.001
-1
What min corresponds to VCM2 = 1
VCMD 5 V = X min-1? 3750 (Note)
VCMD of 5 V? VCM1 = 1
TCMD X Ap. Amp.? Maximum amplifier current (A) 40 A 40
SPEED Constantly
What min-1 corresponds to
(number of 5 V = X min-1? - 3750 (rotary
SPEED of 5 V?
revolutions) motor)
NOTE
To observe the VCMD signal as the number of
positional deviation pulses, input conversion values
listed in Tables I (c) to (e).
To exit the system setting screen, press the F10 key.
- 649 -
<3> To specify measurement intervals, press the F5 key to display the

parameter setting screen.
Pressing numeric keys 1, 2, 5, and 0 can change the setting.
Usually select 1 ms.
Use numeric keys 1, 2, 5, and 0 to

specify a measurement interval.
The measurement interval should
usually be 1 ms.
Fig. I.1 (g) Parameter setting screen
To return to the main screen after parameter setting, press the

F10 key.
- 650 -
I.SERVO CHECK BOARD
I.2 ADJUSTING UNEXPECTED DISTURBANCE TORQUE

DETECTION WITH THE CHECK BOARD
(1) Overview
For adjustment of the unexpected disturbance torque detection
function, an estimated disturbance value measurement is made. This
section describes the method of estimated disturbance value
measurement using the check board and the conversion of a check
board output voltage to a load current.
For the method of adjusting the unexpected disturbance torque
detection function, see Section 4.12.
(2) Output of an estimated disturbance value to the check and adjustment of

unexpected disturbance torque detection
By setting the parameter below, an estimated load torque value can be
output to a channel to which the TCMD signal is usually output.
#7 #6 #5 #4 #3 #2 #1 #0
1957 (FS15i) TDOU
2015 (FS16i)
TDOU(#5) Outputs an estimated disturbance value to the check board.

0: The TCMD output channel based on the standard specification is
used.
1: An estimated disturbance value is output to the TCMD output
channel.
Unexpected disturbance torque detection can be adjusted by setting

TDOU to 1 and observing an analog waveform obtained from the
check board.
The following expression is applicable to conversion of an estimated

disturbance value (analog voltage [V]) obtained from the check board
to an estimated disturbance value [Ap]:
Analog voltage from check board [V]

Estimated disturbance value [Ap] = × Maximum amplifier current [Ap]
4.4[V]
* Subsection 4.12.1 introduces the adjustment procedure applicable

when an estimated disturbance value [Ap] is obtained using
SERVO GUIDE. By using a value converted using the expression
above from an analog voltage value obtained from the check board,
the same adjustment as made in Subsection 4.12.1 can be made
with the analog check board.
- 651 -
I.3 ADJUSTING LINEAR MOTOR AMR OFFSET WITH THE

CHECK BOARD (INCREMENTAL TYPE)
(1) Overview
This section describes how the AMR offset of a linear motor using an
incremental type linear encoder can be adjusted using the check board.
For the method using SERVO GUIDE, see Subsection 4.14.1.

below.
Activating phase measurement
(1) Connect the servo check board to the CNC.
(2) Set the 7-segment LED on check board CH1 as follows:

Set the axis number of parameter No. 1023 in the AXIS digit.
Set 5 in the DATA digit.
(3) For activating phase measurement, set the parameter below.
1726 (FS15i) Parameter for internal data measurement

2115 (FS16i)
Series 9096:
326 for an odd-numbered axis and 966 for an even-numbered axis
Series 90B0, 90B1, 90B5, or 90B6:
326 for an odd-numbered axis and 2374 for an even-numbered axis
Under this condition, the activating phase is output from CH1 on the
check board.
To use a digital check board to measure data with a personal computer,
set up "SD" (servo tuning software) as stated below. The displayed
value is in degree units ("360 degrees" is displayed as "360").
DOS prompt > SD INIT [Enter]
o (Origin of position)
F9 (System setting)
0 (CH0)
2 [Enter] (TCMD)
639.84375 [Enter] (A)
F10 (Return to main menu.)
* See Item (9) in Appendix I.1 for explanations about how to use
the SD software.
In addition, the analog voltage from the check board can be
observed using an oscilloscope. In output conversion, 2.5 V
corresponds to 360 degrees.
* When a linear motor is used, a value from 0° to 360° can be

read each time a movement is made by the inter-pole
distance (between the N and S poles of a magnet).
- 652 -
I.SERVO CHECK BOARD
(4) Run the linear motor using a JOG operation for example, and
observe the behavior of the activating phase (AMR) before, at
the moment, and after phase Z is captured. (See Figs. I.3 (a) and
(b).)
The activating phase changes to 0 (or 360) degrees at the moment
phase Z is captured. Measure the value just before it changes,
and let this value be A.
360° 360°
45° (0.3 V) or lower (*) 315° (2.2 V) or higher (*)
Phase Z Phase Z
Fig. I.3 (a) If the offset is set with a positive number Fig. I.3 (b) If the offset is set with a negative number
(before AMR offset adjustment) (before AMR offset adjustment)
(*) The figures above show examples where AMR60 = 0. When

AMR60 = 1, "45° (0.3 V) or lower" should read "60° (0.4 V) or
lower", and "315° (2.2 V) or higher" should read "60° (2.1 V) or
higher".
(5) Set the AMR offset parameter with A (or A - 360).

* The parameter setting range is:
When the value of A does not lie within the setting range, the
installation position of the linear encoder needs to be readjusted.
The voltage range of A allowing parameter setting, when
measured by analog voltage, is as follows:
0 V to 0.3 V and 2.2 V to 2.5 V (when AMR60 = 0)
0 V to 0.4 V and 2.1 V to 2.5 V (when AMR60 = 1)
(6) Switch the power off and on again. Now parameter setting is
completed.
(7) Observe the activating phase (AMR) again according to step (2)
above, and check that the activating phase changes continuously
in the phase Z rising portion.
(8) Switch the power off and on again. This completes parameter
setting.
(9) After completing the adjustment, reset to 0 the parameter set in

step (3).
- 653 -
45° (0.3 V) or lower (*) 315° (2.2 V) or lower (*)

360° 360°
Phase Z Phase Z
Fig. I.3 (c) If the offset is set with a positive number Fig. I.3 (d) If the offset is set with a negative number
(after AMR offset adjustment) (after AMR offset adjustment)
(*) The figures above show examples where AMR60 = 0. When

AMR60 = 1, "45° (0.3 V) or lower" should read "60° (0.4 V) or
lower", and "315° (2.2 V) or higher" should read "300° (2.1 V)
or higher".
- 654 -
I.SERVO CHECK BOARD
I.4 ADJUSTING SMOOTHING COMPENSATION FOR A

LINEAR MOTOR WITH THE CHECK BOARD
(1) Overview
This section describes the method of adjusting the parameter for
smoothing compensation for a linear motor by using the check board
and the servo adjustment software SD.
For the smoothing compensation function and the method of

adjustment using SERVO GUIDE, see Subsection 4.14.3.

Follow the procedure described below to measure the activating phase
angle and torque command necessary to determine the correction
parameters.
The following procedure use terms "odd-numbered axis" and
"even-numbered axis" in relation to axis numbers specified in
parameter No. 1023 (common to the Series 15i and Series 16i and so
on).
<1> Series 90B0: Does not require step <1>. Go to step <2>.
Series 9096: To measure an odd-numbered axis, set a dummy bit
to 1 for the even-numbered axis paired with it.
If a linear motor is used in tandem control, however, do not set a
dummy bit for the paired axis.
#7 #6 #5 #4 #3 #2 #1 #0
- SERD
2009 (FS16i)
SERD (#0) Specifies whether to enable the dummy serial feedback function.
0: To disable
1: To enable ← To be set
* Do not forget to restore the previous setting after parameter
setting is completed.
<2> Set the check board. Note that the method of setting varies
according to the type of check board used.
<a> When using A06B-6057-H620 (digital check board), set the

DIP switches on the check board as follows:
- 655 -
To measure an odd-numbered axis:

A06B-6057-H620
CNB CNB CNB CNB CNS
Axis 2 Axis 1 Outputs for PIO-48W PC-Card Output to Analog Spindle
CN13
Input from JA8A
A A A A A A A A
DIP switch
3 2 1 0 3 2 1 0
CNA1
CN12
1
CN11
Data Type Setting
A16B-2300- xxxx xxxx 0001 1010
0 1: High 0: Low
AXIS2: 1 (torque) AXIS1: 10 (phase)
To measure an even-numbered axis:

Axis 2 Axis 1
A A A A A A A A
3 2 1 0 3 2 1 0
0
AXIS2: 3 (torque) AXIS1: 11 (phase)
 When using A06B-6057-H630 (one-piece analog/digital

type), set up the 7-segment LED digits on the check board
as shown below:
* Letter X stands for an axis
X 5 X 1 number specified in parameter
No. 1023.
CH1 CH2
Phase Torque
<3> To measure the activating phase angle, set the following

parameter.
1726 (FS15i) Parameter for internal data measurement

2115 (FS16i)
Series 9096: 1328 (for both odd- and even-numbered axes)
Series 90B0, 90B1, 90B6, 90B5:
704 for odd-numbered axis and 2752 for
even-numbered axis
Steps <2> and <3> enable CH0 and CH1 of the SD software to be
used to measure the motor activating phase angle (CH0) and torque
command (CH1).
- 656 -
I.SERVO CHECK BOARD
<4> Start the "SD" software, and make the following setting.
DOS prompt > SD INIT [Enter]
o (Origin of position)
F9 (System setting)
0 (CH0)
2 [Enter] (TCMD)
1.0 [Enter] (1.0A)
1 (CH1)
2 [Enter] (TCMD)
40 [Enter] (Maximum current for servo amplifier to be used)
F10 (Return to main menu.)
(Ctrl)T (XTYT mode selected)

F2 (Data number)
9000 [Enter] (Number of data items to be measured)
* This description uses the LiS3000B2/2 as an example. It differs

from other models only in the current rating of the servo
amplifier. For small linear motors, set the number of data items
to be measured to 4500.
<5> When determining the correction parameters, set the velocity
gain to a rather low value.
<6> For medium-size and large motors, make a reciprocating motion
for 200 mm or more at F1200 (mm/min).
For small linear motors, make a reciprocating motion for 100 mm
or more at F1200 (mm/min).
<7> Pressing the F1 key (to start measurement) at regular speed
displays the data shown below. (Check that the activating phase
angle-based sine waveform changes from negative to positive at
three points or more.)
CAUTION
Measurement direction varies with the setting of the direction-of-movement
parameter.
[If a direction-specific smoothing compensation is not used]
When the setting is 111: Measurement is performed during forward movement.
When the setting is -111: Measurement is performed during backward
movement.
[If a direction-specific smoothing compensation is used]
(When determining a compensation value for the positive direction)
When the setting is 111: Measurement is performed during forward movement.
When the setting is -111: Measurement is performed during backward
movement.
(When determining a compensation value for the negative direction)
When the setting is 111: Measurement is performed during backward movement.
When the setting is -111: Measurement is performed during forward movement.
Measurement in the wrong direction hinders correct calculation of the correction
parameter.
- 657 -
TCMD
Activating phase angle θ
<8> Pressing [CTRL]+[L] causes the correction parameter values to

be calculated as shown below. Enter the displayed parameter
values. Usually, use the correction parameter values displayed on
the top row.
The parameter values displayed on the middle and bottom rows
are used for special parameter setting.
Middle row: To be used when either quadruple smoothing
compensation or quadruple TCMD output is
selected.
Bottom row: To be used when both quadruple smoothing
compensation and quadruple TCMD output are
selected.
Parameter settings are displayed in a form of, for example:

-25425 ( 156: 175)
This format means that the correction gain (parameter high byte)
and correction phase (parameter low byte) are, respectively, 156
and 175.
Because 156 = 9Ch and 175 = AFh,
parameter setting = 9CAFh = -25425.
- 658 -
I.SERVO CHECK BOARD
When specifying the smoothing compensation (negative

direction) parameters (Nos. 2782 to 2784 (Series 15i) or Nos.
2369 to 2371 (Series 16i and so on)), it is impossible to use the
parameter values stated on the previous pages without modifying
them. It is necessary to shift the phase by 128.
Example)
Assuming that the correction gain and correction phase
measured in the negative direction are, respectively, 10 and
100:
10 = 0Ah
100 + 128 = 228 = E4h
Therefore, the parameter value is:
0AE4h = 2788
* If the sum of the phase data and 128 exceeds 255, perform the
following calculation:
Phase data = value that was read + 128 - 256
The December 1999 version and later of the SD software can

display correction parameters for the negative direction. When
using these versions, use the parameter values displayed on the
right section without modifying them.
Compensation for Compensation for the

the positive direction negative direction
Example of measurement
(a) Measured waveform where parameter value calculation is
possible
- 659 -
(b) Measured waveform where parameter value calculation is

impossible (No. 1)
Two activating phase angle-based sine waves cannot be acquired
because of insufficient measurement time.
(c) Measured waveform where parameter value calculation is

impossible (No. 2)
Two activating phase angle-based sine waves cannot be acquired
because of an inappropriate measurement start position.
- 660 -
I.SERVO CHECK BOARD
I.5 MEASURING FREQUENCY CHARACTERISTICS WITH

THE CHECK BOARD
(1) Overview
Frequency characteristics can be measured with the servo check board
and the disturbance input function.
For the method of measuring frequency characteristics with SERVO

GUIDE, see (6) in Appendix H.
(2) Disturbance input function

The disturbance input function is a function that lets you apply
vibration to axes by entering sinusoidal disturbance wave as a torque
command. With this function, you can get the frequency
characteristics of the velocity loop of the system (including machine
sections).
Sweeping sinusoidal
disturbance input (within
servo software)
Open-loop torque command

Disturbance torque input
+ Feed axis
PI control
unit Filter
+ +
-
Velocity feedback

(Series 20i-B)
(3) Parameter setting method

Set the parameters below to use the disturbance input function.
NOTE
In the text below, the terms L axis and M axis are
used. Their meanings are:
L axis: Axis with an odd number set in No. 1023
M axis: Axis with an even number set in No. 1023
- 661 -
#7 #6 #5 #4 #3 #2 #1 #0
2683 (FS15i) DSTIN DSTTAN DSTWAV
2270 (FS30i, 16i)
DSTIN(#7) DISTURBANCE INPUT
0 : Stop
1 : Start (a change of 0 → 1 triggers disturbance input.)
DSTTAN(#6) A disturbance input type is specified as follows:
0 : Input for only one axis
1 : Input for both L and M axes (for synchronous and tandem axes,
setting is to be made only for the L axis.)
DSTWAV(#5) The input waveform of disturbance input is:
0: Sine wave. (Usually, select the sine wave.) .
1: Square wave.
2739 (FS15i) Disturbance input gain

2326 (FS30i, 16i)
[Default value] 0
[Valid data range] 0 to 7282 (to be set in Tcmd units; a value of 7282 corresponds to an
amplifier maximum current.)
Usually, specify 500 to apply vibration to the machine so that it will
sound lightly.
2740 (FS15i) Disturbance input function start frequency (Hz)

2327 (FS30i, 16i)
2741 (FS15i) Disturbance input end frequency

2328 (FS30i, 16i)
[Default value] 200
[Valid data range] 1 to 2000 (Unit : Hz)
2742 (FS15i) Number of disturbance input measurement points

2329 (FS30i, 16i)
[Default value] 3
[Valid data range] SWEPT SINE MODE 1 to 32767
Continuous sine mode Less than 0
Usually, specify 0 or greater to make the machine vibrate in swept
sine mode.
(4) Cautions
• Turn off the functions that work only when the machine is at a
halt, such as the variable proportional gain function in the stop
state and the overshoot compensation function.
• When measuring cutting characteristics, pay attention to which
function type, cutting or rapid traverse, is in use.
• Decrease the position gain to about 1000.
- 662 -
I.SERVO CHECK BOARD
(5) How to use

The default disturbance input setting is the swept sine mode.
When the rising edge of the disturbance input bit is detected,
application of vibration is started. Vibration is automatically stopped
when sine sweeping from the start frequency to the end frequency is
completed. A reset or an emergency stop makes the machine stop
operating. After the emergency stop is released, turning the function
bit off and on again restarts disturbance input.
• Example of setting
No2326 = 500 → gain = 500
No2327 = 0 → start frequency = 10 Hz
No2328 = 0 → end frequency = 200 Hz
No2329 = 0 → repetition = 3 times
(6) Setting for outputting input/output data to the check board

Make the following settings so that the disturbance input frequency
and current command can be observed on the check board.
1726 (FS15i) Shift amount

2115 (FS30i, 16i)
[Setting value] 4
1774 (FS15i) Disturbance input frequency

2151 (FS30i, 16i)
[Setting value] 2629 for the L axis and 2757 for the M axis
2108 for the L axis and 2236 for the M axis (for the Series 90B3 and
90B7)
1775 (FS15i) Shift amount

2152 (FS30i, 16i)
[Setting value] 2
1776 (FS15i) Current command

2153 (FS30i, 16i)
[Setting value] 268 for the L axis and 396 for the M axis
2372 for the L axis and 2500 for the M axis (for the Series 90B3 and
90B7)
- 663 -
(7) Servo tuning software “SD” setting

On the F9 screen of the servo tuning software “SD”, specify data
conversion for each channel. Select 2:Tcmd. Specify 7282 for the
current command channel and 1820 for the disturbance input
frequency channel. For channel data settings on the check board,
the disturbance input frequency and the current command are set,
respectively, to 5 (for a DIP switch, 12) and 6 (for a DIP switch,
13).
Entering a trigger at the same time as the start of disturbance
input collects the data shown below.
Gain
characteristic
Input sine wave

frequency
Resonance
point
Current command
amplitude
Frequency
The envelope of the current command amplitude indicates the gain

characteristic of the velocity loop.
- 664 -
J.USING THE SERVO CHECK
B-65270EN/07 APPENDIX INTERFACE UNIT
J USING THE SERVO CHECK INTERFACE

UNIT
(1) Overview
With CNCs of the FS30i Series, SERVO GUIDE is basically used for
servo adjustment and the servo check board connectable to
conventional CNCs is not supported. Instead, a servo check interface
unit is available. The servo check interface unit is connected to the
FSSB (FANUC serial servo bus) and can be used, for example, to
measure a VCMD waveform, which has been measurable with the
conventional servo check board, by using an external measuring
instrument directly.

(3) Hardware
Additional Basic
CP11L/M
JV13L JV11L
JF103L JF101L
JV14L JV12L
JF104L JF102L
JA4M JA4L
On the servo check interface unit, two connectors, one for analog
signal output and the other for detector data input, are set with one
CNC axis.
JV1xL : Connector for analog signal output
JF10xL : Connector for detector data input
- 665 -
J. USING THE SERVO CHECK
INTERFACE UNIT APPENDIX B-65270EN/07
(4) Parameter setting
CNC
Axis control card

COP10A-1 1st FSSB line 1st I/F unit 2nd I/F unit
ATR=64 ATR= -56
2nd FSSB line
COP10A-2 3rd I/F unit 4th I/F unit
ATR=80 ATR= -40
Additional axis board
3rd FSSB line 1st I/F unitﾄ 2nd I/F unit
COP10A-3
ATR=64 ATR= -56
Fig. J.1 Servo check interface unit connection diagram
#7 #6 #5 #4 #3 #2 #1 #0
- PM2SCB PM1SCB
2278 (FS30i)
PM1SCB(#2) The first or third servo check interface unit is:
0: Not used.
1: Used.
PM2SCB(#3) The second or fourth servo check interface unit is:
0: Not used.
1: Used.
NOTE
1 When these parameters are set, the power must
be turned off before operation is continued.
2 When two servo check interface units are used
with one axis on the CNC, neither a pair of the first
and third units nor a pair of the second and fourth
units may be set. One unit must be selected from
the first and third units, and the other unit must be
selected from the second and fourth units.
- 666 -
With the parameter below, set the type of data to be output to the
servo check interface unit.
- Servo check interface unit output signal setting
2315 (FS30i )
• When using one servo check interface unit with one axis on the
CNC → Set a 2-digit number (decimal).
Tens digit Ones digit

Axis Data
Setting
number(*1) number(*2)
• When using two servo check interface units with one axis on the
CNC → Set a 4-digit number (decimal).
Setting for data 2 Setting for data 1

Thousands Hundreds
Tens digit Ones digit
digit digits
Axis Data Axis Data
Setting
number(*1) number(*2) number(*1) number(*2)
Data 1: Output from the first or third servo check interface unit
Data 2: Output from the second or fourth servo check interface
unit
(*1) Axis number

No. 1023 for axis to be measured
Axis number
Series 90E0 Series 90D0
1 4n+1 2n+1
2 4n+2 2n+2
3 4n+3
4 4n+4
(n=0, 1, 2, ...)
(*2) Data number

Data number Description of measurement data
0 Velocity command (VCMD)
1 Torque command (TCMD)
2 Actual speed (SPEED)
4 Position (POSF)
5 Data 1 for adjustment
6 Data 2 for adjustment
- 667 -
(5) Examples of setting

[Connection example 1] Configuration where the X-axis is a semi-closed axis and the Y-axis
and Z-axis are full-closed axes
Velocity command data is output from the X-axis.
Position data is output from the Y-axis.
No data is output from the Z-axis.
AMP Servo Check
CNC
X/Y/Z I/F Unit
JV11L X-axis analog output
JV12L Y-axis analog output
JF102L Y-axis separate detector input
JF103L Z-axis separate detector input
No. Signal Value

1023X,Y,Z X: 1, Y: 2, Z: 3
1815X,Y,Z#1 OPTx X: 0, Y: 1, Z: 1
1902 FMD 1
1905X,Y,Z#7 PM2 X: 0, Y: 0, Z: 0
1905X,Y,Z#6 PM1 X: 1, Y: 1, Z: 1
1936X,Y,Z X: 0, Y: 1, Z: 2
1937X,Y,Z X: 0, Y: 0, Z: 0
14340 to 14357 ATR 0,1,2,64 The others are –96.
14358 to 14375 ATR All -96
14408 to 14425 ATR All -96
14376 to 14383 ATRC 0,1,2,32,32,32,32,32
14384 to 14391 ATRC All 32
14392 to 14399 ATRC All 32
14400 to 14407 ATRC All 32
14444 to 14451 ATRC All 32
14452 to 14459 ATRC All 32
2278#3 PM2SCB X: 0, Y: 0, Z: 0
2278#2 PM1SCB X: 1, Y: 1, Z: 0
2315 X: 10, Y: 24, Z: 0
- 668 -
[Connection example 2] Configuration where the X-axis is a semi-closed axis and the Y-axis
and Z-axis are full-closed axes
Velocity data is output from the X-axis.
Torque command data is output from the Y-axis.
No data is output from the Z-axis.
AMP Servo Check

CNC I/F Unit
X/Y/Z
JV11L X-axis analog output
JV12L Y-axis analog output
Separate I/F Y-axis separate detector input

Unit
Z-axis separate detector input
No. Signal Value

1023X,Y,Z X: 1, Y: 2, Z: 3
1815X,Y,Z#1 OPTx X: 0, Y: 1, Z: 1
1902 FMD 1
1905X,Y,Z#7 PM2 X: 0, Y: 1, Z: 1
1905X,Y,Z#6 PM1 X: 1, Y: 1, Z: 0
1936X,Y,Z X: 0, Y: 1, Z: 0
1937X,Y,Z X: 0, Y: 0, Z: 1
14340 to 14357 ATR 0,1,2,64,-56 The others are -96.
14358 to 14375 ATR All -96
14408 to 14425 ATR All -96
14376 to 14383 ATRC 0,1,32,32,32,32,32,32
14384 to 14391 ATRC 1,2,32,32,32,32,32,32
14392 to 14399 ATRC All 32
14400 to 14407 ATRC All 32
14444 to 14451 ATRC All 32
14452 to 14459 ATRC All 32
2278#3 PM2SCB X: 0, Y: 0, Z: 0
2278#2 PM1SCB X: 1, Y: 1, Z: 0
2315 X: 12, Y: 21, Z: 0
- 669 -
(6) Changing the output signal units and so forth

To the servo check interface unit, a voltage within ±10 V is output.
The table below indicates the default output unit of each data item.
Data Data output unit

Description of data
number (Default)
0 Velocity command (VCMD) 0.9155min-1/5V
1 Torque command (TCMD) Max. amplifier current min-1/4V
2 Actual speed (SPEED) 3750min-1/5V
4 Position (POSF) 3276.7[detection unit]/1V
5 Data 1 for adjustment -
6 Data 2 for adjustment -
With the parameters below, the output units and so forth of a velocity
command, torque command, and actual speed can be changed as with
conventional check board output.
#7 #6 #5 #4 #3 #2 #1 #0
- TDOUT
2015 (FS30i)
TDOUT(#5) Instead of a torque command, a disturbance torque is:
0: Not output.
1: Output.
#7 #6 #5 #4 #3 #2 #1 #0
- VCM2 VCM1
2012 (FS30i)
When a rotary motor is used

VCM2 VCM1 Specified speed/5V
0 0 0.9155min-1
0 1 14min-1
1 0 234min-1
1 1 3750min-1
When a linear motor is used (Incremental: P=Signal pitch [µm])

(Absolute: P=Resolution [µm] × 512)
VCM2 VCM1 Specified speed/5V
0 0 0.00375 × P m/min
0 1 0.06 × P m/min
1 0 0.96 × P m/min
1 1 15.36 × P m/min
Observe the entire movement in the DC mode with an oscilloscope

then extend the range in the AC mode to check for fine fluctuations
and positional variations.
- 670 -
#7 #6 #5 #4 #3 #2 #1 #0
- TSA05 TCMD05
2225 (FS30i)
TSA05(#2) The TCMD signal check board output voltage is:
0: Ordinary (default).
1: Halved.
* The actual output voltage is affected by the function bit
(TCMD4X) indicated below.
TCMD05(#1) The SPEED signal check board output voltage is:
0: Ordinary (3750min-1/5V) (default).
1: Halved (7500min-1/5V).
The function bit (TCMD4X) indicated below increases the TCMD
output voltage weight by a factor of 10 when compared with the
conventional value. This function bit can be used together with the bit
above (TCMD05).
#7 #6 #5 #4 #3 #2 #1 #0
- TCMD4X
2203 (FS30i)
TCMD4X(#5) The TCMD signal check board output voltage is:
0: Ordinary (default).
1: Increased by a factor of 4.
By using these function bits, the output ranges of the TCMD signal
and SPEED signal can be changed as indicated below.
• TCMD signal output range

TCMD4X TCMD05 TCMD value/4.4V Remarks
0 1 Max. amplifier current × 2 (A)
0 0 Max. amplifier current (A) Conventional mode
1 1 Max. amplifier current/2 (A)
×4 compared with
1 0 Max. amplifier current/4 (A)
conventional mode
Example:
Relationship between the output voltage and TCMD value [A]
when an 80-A amplifier is used
TCMD4X TCMD05 TCMD value/4.4V
0 1 160 [A]
0 0 80 [A]
1 1 40 [A]
1 0 20 [A]
- 671 -
• SPEED signal output range
Actual speed/5V Actual speed/5V

TSA05 Remarks
Rotary motor Linear motor
0 3750 [min-1] 15.36×P [m/min] Conventional mode
1 7500 [min-1] 30.72×P [m/min]
* When a linear motor is used, the meaning of P depends on the
type of scale.
♦ When a high resolution serial output circuit manufactured by

FANUC is used
(Incremental scale) → P=Signal pitch [µm]
♦ When a scale supporting the FANUC serial interface is used

(Absolute scale) → P=Resolution [µm] × 512
- 672 -
B-65270EN/07 INDEX
INDEX
DEFINITION OF WARNING, CAUTION, AND
<α >
NOTE ............................................................................. s-1
αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT... 78
DETAILS OF HIGH-SPEED AND HIGH-PRECISION
<A> ADJUSTMENT.............................................................614
ABBREVIATIONS OF THE NC MODELS COVERED DETAILS OF PARAMETERS .....................................473
BY THIS MANUAL.........................................................5 DETAILS OF THE SERVO PARAMETERS FOR
Acceleration Feedback Function ................................... 158 Series 30i, 31i, 32i, 15i, 16i, 18i, 21i, 0i, 20i,
Acceleration Monitor Function ....................................... 86 Power Mate i (SERIES 90D0, 90E0, 90B0, 90B1, 90B6,
ACTIONS FOR ALARMS ............................................. 87 90B5, AND 9096) .........................................................474
Actions for Illegal Servo Parameter Setting Alarms ....... 61 Detection of an Overheat Alarm by Servo Software
Actual Current Peak Hold Display .................................. 85 when a Linear Motor and a Synchronous Built-in Servo
ADJUSTING LINEAR MOTOR AMR OFFSET WITH Motor are Used..............................................................337
THE CHECK BOARD (INCREMENTAL TYPE)....... 652 Detection of an Overheat Alarm by Servo Software
ADJUSTING PARAMETERS FOR HIGH-SPEED when a Synchronous Built-in Servo Motor are Used ....382
AND HIGH-PRECISION MACHINING ....................... 96 Diagnosis Information List..............................................82
ADJUSTING SMOOTHING COMPENSATION FOR Disturbance Elimination Filter Function
A LINEAR MOTOR WITH THE CHECK BOARD.... 655 (Low-Frequency Resonance Elimination Filter) ...........176
ADJUSTING UNEXPECTED DISTURBANCE Dual Position Feedback Function (Optional Function) .189
TORQUE DETECTION WITH THE CHECK
<F>
BOARD......................................................................... 651
Feed-forward Function ..................................................202
Adjustment .................................................................... 446
Feed-forward Timing Adjustment Function..................213
Advanced Preview Feed-forward Function................... 206
Fine Acceleration/Deceleration (FAD) Function ..........263
ANALOG SERVO INTERFACE SETTING
Full-closed Feedback Sharing Function ........................445
PROCEDURE ............................................................... 537
Function based on the DI signal for switching
 the distance to lift ..........................................................287
Backlash Acceleration Function.................................... 216 FUNCTION FOR OBTAINING CURRENT OFFSETS
Before Servo Parameter Initialization ...............................9 AT EMERGENCY STOP .............................................311
Block Diagrams............................................................. 454 FUNCTION-SPECIFIC SERVO PARAMETERS .......553
BRAKE CONTROL FUNCTION ................................ 276
<H>
<C> High-Speed HRV Current Control ................................149
Cautions for Controlling One Axis with Two Motors... 450 HIGH-SPEED HRV CURRENT CONTROL ...............138
CONTOUR ERROR SUPPRESSION FUNCTION ..... 202 High-speed Positioning Adjustment Procedure.............119
Current Loop 1/2 PI Control Function .......................... 166 HIGH-SPEED POSITIONING FUNCTION ................257
Cutting/Rapid Feed-forward Switching Function ......... 211 How to Use the Dummy Feedback Functions for
CUTTING/RAPID SWITCHING FUNCTION ............ 150 a Multiaxis Servo Amplifiers when an Axis is not in
Cutting/Rapid Unexpected Disturbance Torque Use ................................................................................275
Detection Switching Function ....................................... 307 HRV1 CONTROL PARAMETERS FOR FOR α
SERIES, β SERIES, AND CONVENTIONAL LINEAR
<D>
MOTORS ......................................................................603
Damping Compensation Function................................. 439
HRV2 CONTROL PARAMETERS FOR βM SERIES
Data Measurement and Diagnosis with a PWM
MOTORS ......................................................................612
Distribution Module (PDM).......................................... 394
i-1
INDEX B-65270EN/07
 PARAMETERS FOR HRV2 CONTROL.....................516

INITIALIZING SERVO PARAMETERS ........................9 PARAMETERS FOR Power Mate i .............................549
INTERACTIVE FORCE COMPENSATION PARAMETERS FOR Series 15i ...................................545
FUNCTION .................................................................. 398 PARAMETERS FOR Series 16i, 18i, 21i, AND 0i ......547
PARAMETERS FOR Series 30i, 31i, AND 32i ...........551
<L>
PARAMETERS FOR SERVO HRV2 CONTROL .......602
Lifting function against gravity at emergency stop ....... 283
PARAMETERS RELATED TO HIGH-SPEED AND
Lifting Function Against Gravity at Emergency Stop... 283
HIGH PRECISION OPERATIONS..............................563
LINEAR MOTOR PARAMETER SETTING .............. 312
PARAMETERS SET WITH VALUES IN
Low-speed Integral Function ........................................ 261
DETECTION UNITS....................................................544
<M> Position Gain Switching Function.................................257
MACHINE RESONANCE ELIMINATION Preload Function ...........................................................436
FUNCTION .................................................................. 168 Procedure for Setting the Initial Parameters of Linear
Machine Speed Feedback Function............................... 196 Motors ...........................................................................312
Machining Point Control............................................... 199 Procedure for Setting the Initial Parameters of
MEASURING FREQUENCY CHARACTERISTICS Synchronous Built-in Servo Motors..............................346
WITH THE CHECK BOARD ...................................... 661
<Q>
Method of setting a distance to lift in µm ..................... 290
QUICK STOP FUNCTION ..........................................280
METHOD OF USING THE SERVO CHECK
Quick Stop Function at OVL and OVC Alarm .............294
BOARD......................................................................... 638
Quick Stop Function for Hardware Disconnection of
MODEL-SPECIFIC INFORMATION.......................... 564
Separate Detector ..........................................................291
Motor Feedback Sharing Function ................................ 444
Quick Stop Function for Separate Serial Detector
MOTOR ID NUMBERS OF α SERIES MOTORS...... 598
Alarms...........................................................................293
MOTOR ID NUMBERS OF β SERIES MOTORS ...... 600
Quick Stop Type 1 at Emergency Stop .........................280
MOTOR ID NUMBERS OF CONVENTIONAL
Quick Stop Type 2 at Emergency Stop .........................282
LINEAR MOTORS....................................................... 601
Motor Models and System Configurations.................... 388 <R>
Rapid Traverse Positioning Adjustment Procedure.......122
<N>
RELATED MANUALS ....................................................6
N Pulses Suppression Function ..................................... 164
Resonance Elimination Filter Function
Notes on Using the Control Axis Detach Function ......... 77
(High-Frequency Resonance Elimination Filter)...........171
<O> Resonance Elimination Filter L
Observer Function......................................................... 183 (Low-Frequency Resonance Elimination Filter) ...........180
Overall Use of the Quick Stop Functions...................... 295 RISC Feed-forward Function ........................................209
Overshoot ...................................................................... 132
<S>
OVERSHOOT COMPENSATION FUNCTION.......... 251
Selecting a Resonance Elimination Function ................168
OVERVIEW .....................................................................1
Serial Feedback Dummy Functions...............................272
 SERIAL FEEDBACK DUMMY FUNCTIONS ...........272
Parameter Initialization Flow .......................................... 10 Series 15i-MB ...............................................................564
PARAMETER LIST ..................................................... 505 Series 16i/18i/21i/0i/0i Mate-MB, 0i/0i Mate-MC/
PARAMETERS FOR α AND OTHER SERIES .......... 597 20i-FB ...........................................................................567
PARAMETERS FOR HRV1 CONTROL..................... 506 Series 30i/31i/32i-A, 31i-A5 .........................................577
PARAMETERS FOR HRV1 CONTROL Servo Alarm 2-axis Simultaneous Monitor Function ....442
(FOR Series 0i-A) ......................................................... 531
i-2
B-65270EN/07 INDEX
SERVO CHECK BOARD OPERATING <T>

PROCEDURE ............................................................... 637 TANDEM DISTURBANCE ELIMINATION
SERVO FUNCTION DETAILS ................................... 133 CONTROL (POSITION TANDEM) (Optional
SERVO FUNCTIONS .................................................. 593 Function) .......................................................................418
SERVO GUIDE ............................................................ 455 Tandem Speed Difference Alarm Function...................452
SERVO HRV CONTROL............................................. 134 Torque Command Filter (Middle-Frequency Resonance
Servo HRV Control Adjustment Procedure .................... 96 Elimination Filter) .........................................................169
Servo HRV2 Control..................................................... 137 TORQUE CONTROL FUNCTION ..............................415
Servo HRV3 Control..................................................... 138 TORQUE TANDEM CONTROL FUNCTION
Servo HRV4 Control..................................................... 144 (Optional Function) .......................................................430
Servo Parameter Initialization Procedure........................ 11 Torsion Preview Control Function ................................241
SERVO PARAMETERS RELATED TO HIGH-SPEED Two-stage Backlash Acceleration Function ..................223
AND HIGH PRECISION OPERATIONS .................... 580

SERVO SOFTWARE AND SERVO CARDS
Unexpected Disturbance Torque Detection Function....296
SUPPORTED BY EACH NC MODEL ............................2
UNEXPECTED DISTURBANCE TORQUE
Servo Tuning Screen ....................................................... 79
DETECTION FUNCTIONDISTURBANCE TORQUE
SERVO TUNING SCREEN AND DIAGNOSIS
DETECTION ................................................................296
INFORMATION............................................................. 79
Unexpected Disturbance Torque Detection Switching
SERVO TUNING TOOL SERVO GUIDE................... 455
Function Depending on Acc..........................................309
SETTING αiS/αiF/βiS SERIES SERVO
USING THE SERVO CHECK INTERFACE UNIT ....665
PARAMETERS ................................................................8
SETTING PARAMETERS FOR LARGE SERVO <V>
MOTORS ...................................................................... 388 Variable Proportional Gain Function in the Stop State .160
Setting Parameters in the PWM Distribution Module Velocity Feedback Average Function ...........................441
Configuration ................................................................ 391 VELOCITY LIMIT VALUES IN SERVO
Setting Parameters in the Torque Tandem SOFTWARE .................................................................587
Configuration ................................................................ 389 Velocity Loop High Cycle Management Function........156
Setting Parameters when an αiCZ Sensor is Used .......... 46 Velocity loop integrator copy function .........................451
Setting Parameters When an Acceleration Sensor or Vibration Damping Control Function............................187
Temperature Detection Circuit Is Used........................... 52 Vibration during Travel.................................................129
Setting Servo Parameters when a Separate Detector for Vibration in the Stop State ............................................127
the Serial Interface is Used.............................................. 33 VIBRATION SUPPRESSION IN THE STOP STATE 156
Setting Servo Parameters when an Analog Input
Separate Detector Interface Unit is Used ........................ 44
Smoothing Compensation for Linear Motor ................. 341
Smoothing Compensation for Synchronous Built-in
Servo Motor .................................................................. 383
Static Friction Compensation Function ......................... 238
Stick Slip ....................................................................... 131
SYNCHRONOUS AXES AUTOMATIC
COMPENSATION........................................................ 426
SYNCHRONOUS BUILT-IN SERVO MOTOR
PARAMETER SETTING ............................................. 346
i-3
Revision Record
FANUC AC SERVO MOTOR αi/βi series, LINEAR MOTOR LiS series,
SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series PARAMETER MANUAL (B-65270EN)
• Applied to Series30i/31i/32i
• Addition of HRV4 control
05 May., 2005 • Total revision of chapter of Parameter Adjustment
• Addition of functions added after issue of Edition 04
• Correction of errors
• Addition of the SERVO MOTOR βis series

04 Oct., 2003 • Addition of functions added after issue of Edition 03
• Addition of the SERVO MOTOR αis series

• Addition of item for SERVO GUIDE(Ver 2.00)
03 Mar., 2003
• Addition of the parameter tables for αHVi

• Addition of item for SERVO GUIDE • Addition of functions added after issue of Edition 06
02 Sep., 2002 07 Feb., 2008
• Addition of functions added after issue of Edition 01 • Correction of errors
• Model name change

• Addition of the DiS series motor
01 May, 2001 06 Feb., 2006
Edition Date Contents Edition Date Contents

B-65270EN/07
* B - 6 5 2 7 0 E N / 0 7 . 1 2 *
ADDITIONAL INFORMATION
Notice of the Update of Digital Servo Software for Series 30i/31i/32i (90D0 & 90E0)
1. Type of applied documents
Name FANUC AC SERVO MOTOR αi series

FANUC SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series
Parameter manual
Spec. No./Ver. B-65270EN / 07
2. Summary of Change
Group Name / Outline New, Add Applicable

Correct, Del Date
Basic Function 1. Illegal Parameter Setting Detection of the Add 2008.01
Denominator of Reference Counter Capacity
has been supported.
2. Standard Parameter Table has been changed. Add 2008.01
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another The description of Adaptive Resonance Elimination Filter

function in B-65270EN/07-002 (Edition 01) is deleted. (02)
TITLE
Notice of the Update of Digital Servo
Software for Series 30i /31i /32i (90D0 &
02 2008/03/14 K.Takayama Delete Adaptive Resonance Elimination Filter 90E0)
DRAW. No. CUST.
01 2008/01/08 Y.Ueno Newly designed B-65270EN/07-002 (Edition02)
SHEET
Ed. Date Name Description FANUC LTD 1/5
1. Update Edition
ROM series New edition Available CNC
90D0 17 FS30i /31i (For HRV4 control)
90E0 17 FS30i /31i /32i (For HRV2 and HRV3 control)
2. Contents of change
- Illegal Parameter Setting Detection of the Denominator of Reference Counter Capacity

If we set Reference Counter Capacity by using a fraction, large denominator may induce a system
alarm because the calculation time is prolonged. So the following functions are added,
If the Denominator of Reference Counter Capacity is more than 100, Illegal Parameter Setting
Alarm occurs.
A funciton bit that ignores the Illegal Parameter Setting Alarm is added for the systems that
have already worked on a large value of Denominator of Reference Counter Capacity.
- Change of Standard Parameter Table

Standard Parameter Table has been changed.
3. Attached
Attached 1 Illegal Parameter Setting Detection of the Denominator of Reference Counter

Capacity
Attached 2 Change of Standard Parameter Table
TITLE
90E0)
DRAW. No. CUST.
01 2008/01/08 Y.Ueno Newly designed
B-65270EN/07-002 (Edition02)
SHEET
Attached 2. Illegal Parameter Setting Detection of the Denominator of Reference
Counter Capacity
(1) Outline
It is recommended that the denominator of Reference Counter Capacity is 100 or
less. But in case that the denominator of Reference Counter Capacity is more than
100, the processing time increases and there is a case that system alarm occurs.
This time, the following functions are added.
If the Denominator of Reference Counter Capacity is more than 100, Illegal
Parameter Setting Alarm occurs.
A funciton bit that ignores the Illegal Parameter Setting Alarm is added for the
systems that have already worked on a large value of Denominator of
Reference Counter Capacity.
(2) Available Servo software

(Series 30i, 31i, 32i )
90D0 series version 17(Q) and subsequent editions
90E0 series version 17(Q) and subsequent editions
(3) Parameters
new parameters
#7 #6 #5 #4 #3 #2 #1 #0
No.2299(FS30i) IGNRFA
IGNRFA(#5) Illegal parameter setting detection of the denominator of Reference Counter
Capacity is
0: done.
1: not done.
* If this parameter is changed, CNC must be turned OFF/ON.
related parameters (existing)
No.1821(FS30i) Reference Counter Capacity （numerator）

［setting range］ 0～999999999
No.2179(FS30i) Reference Counter Capacity （denominator）

［setting range］ 0～100
※ After this edition of servo software, if the denominator of Reference Counter
Capacity is set to more than 100, illegal parameter setting alarm will occur
(detail No.1793).
※ This alarm can be ignored if IGNRFA is set to “1”.
(4) Notice
After this edition of servo software, if the denominator of Reference
Counter Capacity is set to more than 100, illegal parameter setting alarm
will occur. If the denominator can not be changed, please set parameter
No.2299#5 to “1”.
TITLE
90E0)
DRAW. No. CUST.
B-65270EN/07-002 (Edition02)
SHEET
Attached 3. Changes of Standard Parameter Table

(Series 30i, 31i, 32i )
Series 90D0/17(Q) and subsequent editions
Series 90E0/17(Q) and subsequent editions
Standard parameters of the following synchronous built-in servo motor are added.
List of Motor Model and ID No. for newly added Motors:

Motor Model Motor ID No. Notice
DiS22/1500 449 200V for HRV3
* These parameters are only for HRV3. They can not be used with HRV2 in place of HRV3.
* Please refer to Table 1 about the standard parameters.
Standard parameters of the following βi servo motors are added.

βiS22/3000 313 200V HRV2, 3
βiS22/3000HV 314 400V HRV2, 3
Standard parameters of the following αi servo motors are added.

αiS22/6000 452 200V HRV2, 3
αiS22/6000HV 453 400V HRV2, 3
TITLE
90E0)
DRAW. No. CUST.
B-65270EN/07-002 (Edition02)
SHEET
[table1] Addition of new standard parameters
DiS22
βiS22 βiS22 αiS22 αiS22
Motor model /1500
3000 3000HV 6000 6000HV
(200V)
Motor specification 0082 0083 0482-B12x 0262 0263
Motor ID number 313 314 449 452 453
Symbol FS 30i, 31i, 32i
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00001000 00001000 00000001 00000000 00000000
2014 00001000 00001000 00000000 00000000 00000000
2210 00000000 00000000 00000100 00000000 00000000
2211 00001110 00001110 00001010 00001010 00001010
2300 00000000 00000000 10000110 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 1157 1146 562 605 605
PK2 2041 -5102 -5267 -1568 -2393 -2393
PK3 2042 -1332 -1332 -2948 -1335 -1335
PK1V 2043 198 192 202 102 102
PK2V 2044 -1766 -1722 -1811 -914 -914
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 4297 4406 4657 4150 4150
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 0 0 0 0 0
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0
PVPA 2057 -6174 -6174 -17944 -12039 -12039
PALPH 2058 -2843 -2843 -2257 -2000 -2000
PPBAS 2059 0 0 0 0 0
TQLIM 2060 5462 5462 7282 7282 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32520 32548 32439 32511 32501
POVC2 2063 3097 2755 4109 3215 3332
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 9212 8192 10559 9565 9912
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 12288 8192 0 4096 4096
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 2121 2069 2576 1977 1977
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 848 869 348 819 819
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 1289 1289 2049 1288 1288
DETQLM 2111 7268 7268 16720 12830 12830
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 1967 3894 0 1000 2000
MFWKCE 2128 6000 6000 6500 1000 1000
MFWKBL 2129 2315 2315 792 3854 3854
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 5647 5647 30735 7690 7690
PHDLY2 2134 12820 12820 10270 8990 8990
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 140 0
POVC21 2162 32765 32765 0 32765 32765
POVC22 2163 40 38 0 34 34
POVCLMT2 2164 7166 6815 0 6222 6222
MAXCRT 2165 85 45 25 165 85
TITLE
90E0)
DRAW. No. CUST.
B-65270EN/07-002 (Edition02)
SHEET

Parameter manual

Correct, Del Date
Basic Function ・ Adaptive Resonance Elimination Filter function Correct 2008.03
has been supported.
・ Standard parameter table has been changed. Add 2008.03
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Notice of the Update of Digital Servo Software
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004
01 08.03.14 K.Takayama Newly designed SHEET
Ed Date Design Description 01／009

1. Update Edition
- Adaptive Resonance Elimination Filter function

Resonance Elimination Filter is a function that realizes high velocity gain due to the elimination of
the mechanical resonance.
“Adaptive Resonance Elimination Filter function” enables one of the four Resonance Elimination
Filters to dynamically adapt the changeable mechanical resonance caused by the following factors,
Changeable resonance depending on machine position.

Changeable resonance depending on slight differences of each machine.
Changeable resonance depending on the process of time.
Changeable resonance depending on the stiffness of work piece.
NOTE
We already reported about Adaptive Resonance Elimination Filter function in the previous
technical reports, B-65270EN/06-011 and B-65270EN/06-009. However, some specifications of
this function has been changed in servo software 90D0, 90E0 / S(19) . When you use Advance
Resonance Elimination Filter, please use servo software 90D0, 90E0/S(19) or later and follow
the specification described on this document.
- Standard parameter table has been changed

Standard parameters for αiF40/3000 and αiF40/3000 with FAN has been changed.
3. Attached
Attached 1 Adaptive Resonance Elimination Filter function

Attached 2 Changes of Standard Parameter Table
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

Attached 1. Adaptive Resonance Elimination Filter function
(1) Outline
Former “ Active Resonance Elimination Filter” was “Resonance Elimination
Filter” which enabled to follow up the changeable mechanical resonance. Lately
“Adaptive Resonance Elimination Filter” was developed which enabled to adapt
to wider frequency band of resonance. This function can be applied to the
changeable mechanical resonance like the following cases.
Changeable resonance depending on machine position.

Changeable resonance depending on an individual difference of machine.
Changeable resonance depending on the process of time.
Changeable resonance depending on the stiffness of work piece.
1) Follow-up mode and Search mode

There are two modes for this function. One of them is follow-up mode. This
mode is applied in case that the high following speed within a narrow bandwidth is
required, such as the changeable resonance depending on machine position.
Another is search mode. This mode is applied in case that the adaptation with
wide bandwidth is required, such as the changeable resonance depending on the
stiffness of work piece.
Characteristic of filter; Characteristic of filter;
Follow-up mode Search mode
Following up gradual change Adapting to large change

of resonance F(Hz) of resonance F(Hz)
2) How to use
Normally follow-up mode is effective during axis feed except stop or PMC
signal ON (G322). Start / Stop of search mode is controlled by PMC signal
(G324).
3) Automatic renewal of parameter

Normally the adaptive result is lost by NC power off. But if N2290#5 is set to 1,
the adaptive result is automatically reflected in parameter (N2113) of Resonance
Elimination Filter 1. If the movable of resonance frequency is detected, the
parameter is renewed after follow-up mode OFF.
In case of search mode, if the movable of resonance frequency is detected, the
detective signal (F370) in PMC becomes ON.
It is possible to confirm the adaptive result on diagnostic display N763.
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

90D0 series version S(19) or later (Series 30i, 31i )
90E0 series version S(19) or later (Series 30i, 31i, 32i )
90E3 series version B(02) or later (Series 30i, 31i, 32i )
(3) Notice
This function is available with first filter (N2113) out of four resonance
elimination filters.
Damping parameter (N2359) is available in this function.
This function is effective after a release of emergency stop.
The following CNC software is required to use parameter automatic renewal.
G002,G012,G022,G032,G101,G111,G121,G131,G201/30 or later
G003,G013,G023,G033,G103,G113,G123,G133,G201/13 or later
(4) Parameters
#7 #6 #5 #4 #3 #2 #1 #0
No.2270 (FS30i) ACREF
ACREF (#3) Adaptive resonance elimination filter
0: Ineffective.
1: Effective.
Set “1” to the axis you want to use this function.
#7 #6 #5 #4 #3 #2 #1 #0
No.2290 (FS30i) FRFPWE FRFDES FRFATE
FRFATE (#3) Executive condition for follow-up mode
0: During axis feed or PMC signal ON (G322)
1: During axis feed except cutting mode or PMC signal ON (G322)
Normally follow-up mode is effective during axis feed or PMC signal ON.
But if this parameter is set, this mode is effective during axis feed except cutting
mode.
FRFDES (#4) Executive condition for follow-up mode

0: Depending on FRFATE (#3)
1: Only depending on PMC signal (G322)
If this parameter is set, follow-up mode depends on PMC signal only.
FRFPWE (#5) Parameter automatic renewal

0: Unavailable
1: Available
Normally the adaptive result isn’t reflected to parameter (N2113) after
adaptation. But if this parameter is set, the result is reflected.
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

No.2113 (FS30i) Resonance Elimination Filter1 : Attenuation center frequency
Data unit Hz
Valid data range 100 to 1kHz (HRV2), to 2kHz (HRV3), to 4kHz (HRV4)
Follow-up range 100 to 990Hz (HRV2), to 1270Hz (HRV3,HRV4)
When this function is effective (N2270#3=1), this filter can adapt attenuation center
frequency to changeable machine resonance within bandwidth (N2351 or N2459).
But if the setting is out of follow-up range, this function is unavailable.
If this parameter is rewritten by manual, the adaptive result is lost .
No.2177 (FS30i) Resonance Elimination Filter1 : attenuation bandwidth

Data unit Hz
Valid data range 10 to (N2113)
No.2359 (FS30i) Resonance Elimination Filter1 : Damping

Data unit Hz
Valid data range 0 to 100
No.2351 (FS30i) Adaptive Resonance Elimination Filter : Follow-up bandwidth

Data unit Hz
Standard setting 0 (If 0 is set, this parameter is internally handled as 40Hz.)
This parameter decides follow-up bandwidth for follow-up mode.
No.2352 (FS30i) Adaptive Resonance Elimination Filter : Detective level

Data unit Torque command (7282 per Imax)
Standard setting more than 48 (If 0 is set, this parameter is internally handled as 16.)
Note
This parameter decides the detective revel of resonance spectrum.
If there is the large noise to disturb the correct detection, please increase this
value. When you use this function, you should confirm the effectiveness of
this function on your machine.
No.2459 (FS30i) Adaptive Resonance Elimination Filter : Search bandwidth

Data unit Hz
Standard setting 0 (If 0 is set, this parameter is internally handled as 890Hz.)
This parameter decides search bandwidth for search mode.

The search range will be from (N2113–N2459)Hz to (N2113+N2459)Hz.
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

(5) PMC Signals
Follow-up mode and Search mode
Follow-up mode can adapt the attenuation center frequency (N2113) to

resonance within follow-up bandwidth (N2351). When high-speed follow-up
within narrow bandwidth (+-40Hz) are required, this mode is effective.
Search mode can adapt the attenuation center frequency (N2113) to resonance
within search bandwidth (N2459). When wide bandwidth for search is required
such as the work change with different resonance, this mode is effective.
Follow-up mode signal G322

[Function] Control start / stop for follow-up mode
[Operation] Normally this mode is effective during axis feed. If this
signal is ON, this mode is effective even if it is stop state.
Search mode signal G324

[Function] Control start / stop for search mode
[Operation] Search mode is effective while this signal is ON.
Search mode detective signal F370

[Function] Inform the finish for search mode
[Operation] If resonance is detected, this signal becomes ON
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

Timing chart
1) Follow-up mode(N2290#5=1) ON
G322
Rapid Cutting
Velocity Stop
Follow-up Follow-up
Condition
Detect Detect
Detection
ON ON
Parameter
renewal
2) Search mode(N2290#5=1)
ON
OFF
G324
Velocity Stop
Search
Condition
Detection
ON
F370
ON
Parameter
renewal
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

(1) Outline
The standard parameters of αiF40/3000 and αiF40/3000 with FAN are
changed to promote stability.

90D0 series version S(19) or later (Series 30i, 31i )
90E0 series version S(19) or later (Series 30i, 31i, 32i )
(3) Changed Standard paremeter
・ αiF40/3000(HRV2 control)[Motor ID =307]

Symbol Parameter No. Before Changed
PK1 No.2040 1613 1500
PK2 No.2041 -7446 -8224
AALPH No.2074 16384 0
・ αiF40/3000 with FAN(HRV2 control) [Motor ID No=308]

Symbol Parameter No. Before Changed
No.2211 00000010 00001010
PK1 No.2040 1613 1500
PK2 No.2041 -7446 -8224
AALPH No.2074 16384 0
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004

Table1) Standard parameter table for changes
Motor Model αiF40/3000 αiF40/3000Fan

Motor Specification 0257 0257
Motor ID No. 307 308
Symbol FS 30i, 31i, 32i
2003 00001000 00001000
2004 00000011 00000011
2005 00000000 00000000
2006 00000000 00000000
2007 00000000 00000000
2008 00000000 00000000
2009 00000000 00000000
2010 00000000 00000000
2011 00100000 00100000
2012 00000000 00000000
2013 00000000 00000000
2014 00000000 00000000
2210 00000000 00000000
2211 00001010 00001010
2300 00000000 00000000
2301 00000000 00000000
PK1 2040 1500 1500
PK2 2041 -8224 -8224
PK3 2042 -1348 -1348
PK1V 2043 191 191
PK2V 2044 -1712 -1712
PK3V 2045 0 0
PK4V 2046 -8235 -8235
POA1 2047 2216 2216
BLCMP 2048 0 0
DPFMX 2049 0 0
POK1 2050 956 956
POK2 2051 510 510
RESERV 2052 0 0
PPMAX 2053 21 21
PDDP 2054 1894 1894
PHYST 2055 319 319
EMFCMP 2056 0 0
PVPA 2057 -2570 -2570
PALPH 2058 -2000 -2000
PPBAS 2059 0 0
TQLIM 2060 7282 7282
EMFLMT 2061 0 0
POVC1 2062 32511 32431
POVC2 2063 3215 4212
TGALMLV 2064 4 4
POVCLMT 2065 9565 12545
PK2VAUX 2066 0 0
FILTER 2067 0 0
FALPH 2068 0 0
VFFLT 2069 0 0
ERBLM 2070 0 0
PBLCT 2071 0 0
SFCCML 2072 0 0
PSPTL 2073 0 0
AALPH 2074 0 0
OSCTPL 2077 0 0
PDPCH 2078 0 0
PDPCL 2079 0 0
DPFEX 2080 0 0
DPFZW 2081 0 0
BLENDL 2082 0 0
MOFCTL 2083 0 0
RTCURR 2086 1957 2593
TDPLD 2087 0 0
MCNFB 2088 0 0
BLBSL 2089 0 0
ROBSTL 2090 0 0
ACCSPL 2091 0 0
ADFF1 2092 0 0
VMPK3V 2093 0 0
BLCMP2 2094 0 0
AHDRTL 2095 0 0
RADUSL 2096 0 0
SMCNT 2097 0 0
DEPVPL 2098 0 0
ONEPSL 2099 400 400
INPA1 2100 0 0
INPA2 2101 0 0
DBLIM 2102 12000 12000
ABVOF 2103 0 0
ABTSH 2104 0 0
TRQCST 2105 1839 1839
LP24PA 2106 0 0
VLGOVR 2107 0 0
RESERV 2108 0 0
BELLTC 2109 0 0
MGSTCM 2110 1291 1291
DETQLM 2111 5220 5140
AMRDML 2112 0 0
NFILT 2113 0 0
NINTCT 2127 3041 3041
MFWKCE 2128 6000 2000
MFWKBL 2129 1560 1553
LP2GP 2130 0 0
LP4GP 2131 0 0
LP6GP 2132 0 0
PHDLY1 2133 2590 3085
PHDLY2 2134 8990 8990
DGCSMM 2159 0 0
TRQCUP 2160 0 0
OVCSTP 2161 140 140
POVC21 2162 32765 32718
POVC22 2163 33 629
POVCLMT2 2164 6099 10707
MAXCRT 2165 165 165
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-004


PARAMETER MANUAL

Correct, Del Date
Basic Function ・ Speed Arrival Signal and Zero-Speed Detecting Add 2008.05
Signal have been supported
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-005
01 08.05.21 Y.Ueno Newly designed SHEET

1. Update Edition
- Speed Arrival Signal and Zero-Speed Detecting Signal

From this edition, Speed arrival signal (SVSAR) and Zero-speed detecting signal (SVSST) that are
used in spindle control by servo motor have been supported.
3. Attached
Attached 1 Speed Arrival Signal and Zero-Speed Detecting Signal
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-005

Attached 1. Speed Arrival Signal and Zero-Speed Detecting Signal
(1) Outline
Speed arrival signal (SVSAR) and Zero-speed detecting signal (SVSST) that are used in spindle
control by servo motor have been supported.
Up to now, to judge speed arrival and zero speed, it’s necessary to observe actual speed by PMC. By
this modification, Speed arrival signal (SVSAR) and Zero-speed detecting signal (SVSST) can be
used as same as spindle control.
These signals are effecive in using Spindle control by servo motor. Please refer to “FANUC Series
30i/31i/32i-A CONECTION MANUAL (FUNCTION)” for the detail of Spindle control with servo motor.

90D0 series version T(20) and subsequent editions (Series 30i, 31i )
90E0 series version T(20) and subsequent editions (Series 30i, 31i, 32i )
(3) Available System software

Please use the following system software in using Speed arrival signal and Zero-speed detecting signal.
(system software)
31.0 and subsequent editions of the following system software series are available.
FS30i-A
G003, G013, G023, G033
G00C, G01C, G02C, G03C
FS31i-A5
G123, G133
G12C, G13C
FS31i-A
G103, G113
FS32i-A
G203
48.0 and subsequent editions of the following system software series are available.
FS30i-A
G002, G012, G022, G032
G00B, G01B, G02B, G03B
FS31i-A5
G121, G131
G12B, G13B
FS31i-A
G101, G111
FS32i-A
G201
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-005

(4) Parameters
2482 (FS30i) Detection level of speed arrival (SARLV)

[setting range] 0～1000
[setting unit] 0.1%
[default value] 0（Setting value “0” means “15”% internally.）
Detection level of speed arrival means the ratio to commanded speed. When the
subtraction of actual speed from commanded becomes lower than (commanded
speed) × (ratio), actual speed is judged as reach to the commanded speed, and
Speed arrival signal, SVSARn becomes “1”.
Commanded speed for the

judgment of speed arrival
speed
The range that speed arrival signal (SVSAR) is “1”
(speed command)×(1±SARLV/1000)
Actual speed
Speed command for speed control

(acceleration or deceleration is included)
time
SVSAR=0 SVSAR=1
2483 (FS30i) Detection level of speed zero (SSTLV)

[setting unit] 1/min
[default value] 0（Setting value “0” means “45”/min internally.）
Detection level of zero speed means the revolution speed(1/min) that is used to judge
stopping. When the actual speed becomes lower than detection level of zero speed,
motor is judged to be stopped, and Zero-speed detecting signal, SVSSTn becomes
“1”.
speed commanded speed for the judgment

of zero speed
actual speed
the range that Zero-speed
detecting signal (SVSST) is “1”
±SSTLV[rpm]
time
SVSST=0 SVSST=1
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-005

(5) PMC Signals
Speed arrival signal SVSAR1~SVSAR8<Fn377>

[Function] This signal shows that the actual speed of the servo motor arrives at the preset
range arround the commanded speed at spindle control by servo motor.
[Operation] - SVSARn becomes “1” when the actual speed arrives at the commanded speed.
- SVSARn becomes “0” when the actual speed has not arrived at the commanded
speed.
Zero-speed detecting signal SVSST1~SVSST8<Fn376>

[Function] This signal shows that the actual speed of the servo motor that is controled by
spindle control by servo motor comes into detection level of zero speed.
[Operation] - SVSSTn becomes “1” when the actual speed is zero.
- SVSSTn becomes “0” when the actual speed is not zero.
signal address
#7 #6 #5 #4 #3 #2 #1 #0
Fn376 SVSST8 SVSST7 SVSST6 SVSST5 SVSST4 SVSST3 SVSST2 SVSST1
#7 #6 #5 #4 #3 #2 #1 #0
Fn377 SVSAR8 SVSAR7 SVSAR6 SVSAR5 SVSAR4 SVSAR3 SVSAR2 SVSAR1
- SVSARn is “0” at emergency stop. So, aftter emergency stop, SVSARn becomes “0” even if the
motor is rotating and in the range of speed arrival. Also in case of some alarms and rotating with
dynamic brake, SVSARn becomes “0”.
- In the case of servo off, SVSARn will be “0”.
- As servo software always watches zero speed condition, SVSSTn will be changed according to
the real motor speed. (The signal condition will not relate to emergency stop, alarm, and servo off.)
- But when the motor feedback alarm (such as communication alarm by disconnection of encoder)
occurs, the feedback data will be unstable. Is such case, there is a possibility tha the output of the
signal might be wrong.
- You can’t use these two signals for safety function, which protects workers from danger by the
machine.
TITLE
for Series 30i /31i /32i (90D0 & 90E0)
DRAW. No. CUST.
B-65270EN/07-005

Notice of the update of Digital Servo Software for Series 0i/16i /18i /21i etc. (90B8/L, 90B1/L)

LINEAR MOTOR LiS series
SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series
PARAMETER MANUAL
Spec. No./Ver. B-65270EN/07
Correct, Del Date
Basic Function 1. Changes of standard parameter table Add 2008.05
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Notice of the update of Digital Servo
Software for Series 0i/16i /18i /21i etc.
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
01 2008.05.21 Ueno Newly designed
Design.
SHEET
Ed. Date Description FANUC LTD 1/7
Notice of the update of Digital Servo Software for Series 0i/16i/18i/21i etc.
(90B8/L, 90B1/L)
.
1. Update Edition

90B8 12 FS0i-C, FS0iMate-C
90B1 12 FS15i, 16i, 18i, 21i, PMi -D, PMi -H
- Changes of standard parameter table

Standard parameter table has been changed.
3. Attached
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
Standard parameters of the following synchronous built-in servo motor are added.

DiS 22/1500 449 200V for HRV3
* When you load standard parameters by using this motor ID number, HRV3 control will be effective.
* In the case, you have to take care of the restrictions regarding HRV3 control (such as axis card and
number of control axes).
* When you want to use HRV2 control, please change following parameters.
- No.1707#0(Series15i)、No.2013#0(Series16i and etc.)=0
- No.1707#6(Series15i)、No.2013#6(Series16i and etc.)=1
* Please refer to “APPENDIX E VELOCITY LIMIT VALUES IN SERVO SOFTWARE” in parameter
manual about velocity limit of series 16i-B, etc.

αiS 300/2000 242 200V for HRV1
αiS 22/6000 452 200V for HRV2,3
αiS 22/6000HV 453 400V for HRV2,3
* Please refer to Table 1,2 about the standard parameters.
* If you have used ID number 115 (α300/2) for HRV1 control of αiS300/2000 ,
please use ID number 242 from this edition.

βiS 22/3000 213 200V for HRV1
βiS 22/3000HV 214 400V for HRV1
βiS 22/3000 313 200V for HRV2, 3
βiS 22/3000HV 314 400V for HRV2, 3
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
In order to promote stability, standard parameters of the following large servo motor are changed.
List of Motor Model and ID No. that standard parameters are changed:
αiF 40/3000 207 200V for HRV1
αiF 40/3000 FAN 208 400V for HRV1
αiF 40/3000 307 200V for HRV2,3
αiF 40/3000 FAN 308 400V for HRV2,3
In order to reduce the heat generation at high-speed rotation, standard parameters of the following large servo
motor are changed.
αiS 2000/2000HV
340 400V NOTE1
（A06B-0091-B040）
Standard parameters of the following large servo motors are added. With these parameters, the optimal control
can be done by making use of DC link voltage information, and heat generation at high-speed rotation can be
reduced.
To apply these parameters, the following conditions on servo software, servo amplifier, and power supply module
must be satisfied.

αiS 2000/2000HV NOTE1
454 400V
（A06B-0091-B040）
αiS 3000/2000HV NOTE1
455 400V
（A06B-0092-B040）
NOTE1: To use these parameters, PDM is necessary. HRV3 (No.2013#0=1) is set for PDM, but the current
control is equivalent to HRV2.
<Condition>
servo software: Series 90B1,90B8/C(3) and subsequent editions
（L(12) and subsequent editions can execute parameter auto loading.）
servo amplifier: A06B-6127-H109 (αi SV-360HV)
power supply module: A06B-6150-H075 (αi PS-75HV)
A06B-6150-H100 (αi PS-100HV)
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
<Notice>
* If servo software, servo amplifier, or power supply module are older version than listed above, do not
use these parameters. (Use motor ID number 340 if αiS2000/2000HV has already used.)
* 90B1,90B8/L(12) and subsequent editions can execute parameter auto loading.
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
Table1) Standard paramter table for changes and new added models (Checked parameters are changed.)
αiF40 αiF40 βiS22 βiS22 αiS300 αiF40 αiF40 βiS22 βiS22
Motor model
3000 3000Fan 3000 3000HV 2000 3000 3000Fan 3000 3000HV
Motor ID number 207 208 213 214 242 307 308 313 314
Symbol FS15i FS 16i, 18i, 21i
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00000000 00000000 00100000 00100000 00100000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00001000 00001000 00000000 00000000 00000000 00001000 00001000
1708 2014 00000000 00000000 00001000 00001000 00000000 00000000 00000000 00001000 00001000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001110 00001110 00000000 00001010 00001010 00001110 00001110
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1289 1289 646 775 1357 1500 1500 1157 1146
PK2 1853 2041 -5048 -5048 -2486 -3580 -4212 -8224 -8224 -5102 -5267
PK3 1854 2042 -2696 -2696 -1298 -2663 -2710 -1348 -1348 -1332 -1332
PK1V 1855 2043 191 191 198 192 114 191 191 198 192
PK2V 1856 2044 -1712 -1712 -1766 -1722 -1023 -1712 -1712 -1766 -1722
PK3V 1857 2045 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 2216 2216 4297 4406 3709 2216 2216 4297 4406
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 3787 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -2570 -2570 -6174 -6174 -3850 -2570 -2570 -6174 -6174
PALPH 1870 2058 -2000 -2000 -2843 -2843 -800 -2000 -2000 -2843 -2843
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 5462 5462 7282 7282 7282 5462 5462
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32511 32431 32520 32548 32391 32511 32431 32520 32548
POVC2 1878 2063 3215 4212 3097 2755 4714 3215 4212 3097 2755
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 9565 12545 9212 8192 23263 9565 12545 9212 8192
PK2VAUX 1894 2066 0 0 -10 -10 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 8192 8192 8192 12288 0 0 12288 8192
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1957 2593 2121 2069 2483 1957 2593 2121 2069
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 15000 15000 0 0 15000 12000 12000 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1839 1839 848 869 10871 1839 1839 848 869
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1291 1291 1289 1289 16 1291 1291 1289 1289
DETQLM 1704 2111 5140 5140 7268 7268 1606 5220 5140 7268 7268
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 3041 3041 1967 3894 0 3041 3041 1967 3894
MFWKCE 1736 2128 2000 2000 6000 6000 5500 6000 2000 6000 6000
MFWKBL 1752 2129 1553 1553 2315 2315 791 1560 1553 2315 2315
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 3087 3087 5647 5647 1556 2590 3085 5647 5647
PHDLY2 1757 2134 8990 8990 12820 12820 20494 8990 8990 12820 12820
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 140 140 0 0 140 140 140 0 0
POVC21 1785 2162 32765 32718 32765 32765 32738 32765 32718 32765 32765
POVC22 1786 2163 33 629 40 38 375 33 629 40 38
POVCLMT2 1787 2164 6099 10707 7166 6815 13952 6099 10707 7166 6815
MAXCRT 1788 2165 165 165 85 45 365 165 165 85 45
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
Table2) Standard paramter table for changes and new added models (Checked parameters are changed.)
αiS2000 DiS22 αiS22 αiS22 αiS2000 αiS3000
Motor model
2000HV 1500(200V) 6000 6000HV 2000HV 2000HV
Motor specification 0091 0482-B12x 0262 0263 0091 0092
Motor ID number 340 449 452 453 454 455
Symbol FS15i FS 16i, 18i, 21i
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 01000011 00000011 00000011 00000011 01000011 01000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000001 00000001 00000000 00000000 00000001 00000001
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000100 00000000 00000000 00000000 00000000
1751 2211 00011110 00001010 00001010 00001010 00011110 00011010
2713 2300 00000000 10000110 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 643 562 605 605 643 772
PK2 1853 2041 -3600 -1568 -2393 -2393 -3600 -3819
PK3 1854 2042 -1358 -2948 -1335 -1335 -1358 -1357
PK1V 1855 2043 502 202 102 102 502 652
PK2V 1856 2044 -4500 -1811 -914 -914 -4500 -5836
PK3V 1857 2045 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 843 4657 4150 4150 843 650
BLCMP 1860 2048 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21
PDDP 1866 2054 3787 1894 1894 1894 3787 3787
PHYST 1867 2055 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0
PVPA 1869 2057 -2595 -17944 -12039 -12039 -3363 -2088
PALPH 1870 2058 -3200 -2257 -2000 -2000 -3200 -5000
PPBAS 1871 2059 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0
POVC1 1877 2062 32309 32439 32511 32501 32309 32309
POVC2 1878 2063 5734 4109 3215 3332 5734 5734
TGALMLV 1892 2064 4 4 4 4 4 4
POVCLMT 1893 2065 27346 10559 9565 9912 27346 27346
PK2VAUX 1894 2066 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0
AALPH 1967 2074 12288 0 4096 4096 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0
RTCURR 1979 2086 2893 2576 1977 1977 2893 3187
TDPLD 1980 2087 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0
TRQCST 1998 2105 6221 348 819 819 6221 8472
LP24PA 1999 2106 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0
MGSTCM 1703 2110 784 2049 1288 1288 784 267
DETQLM 1704 2111 1510 16720 12830 12830 1510 2218
AMRDML 1705 2112 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0
NINTCT 1735 2127 3449 0 1000 2000 3449 3029
MFWKCE 1736 2128 3000 6500 1000 1000 3000 2700
MFWKBL 1752 2129 1291 792 3854 3854 1291 777
LP2GP 1753 2130 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0
PHDLY1 1756 2133 2060 30735 7690 7690 2060 2068
PHDLY2 1757 2134 12820 10270 8990 8990 12820 6410
DGCSMM 1782 2159 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0
OVCSTP 1784 2161 140 0 140 0 140 140
POVC21 1785 2162 32745 0 32765 32765 32745 32745
POVC22 1786 2163 292 0 34 34 292 292
POVCLMT2 1787 2164 13952 0 6222 6222 13952 13952
MAXCRT 1788 2165 0 25 165 85 0 0
ACCBSLM 2717 2304 2720 0 0 0 2720 0
ACDCEND 2718 2305 4114 0 0 0 4114 22
DCIDBS 2723 2310 0 0 0 0 1236 1112
TITLE
(90B8/L, 90B1/L)
DRAW. No.
B-65270EN/07-006
CUST.
Design.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/31i ( 90D0)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Addition of the function setting bit for Add 2008.07
Synchronous Built–in Servo Motor DiS with
high-resolution serial output circuit H or C
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
for Series 30i /31i (90D0)
DRAW. No. CUST.
B-65270EN/07-007
01 08.07.04 Tang Newly designed SHEET

Notice of the Update of Digital Servo Software for Series 30i/31i ( 90D0)
1. Update Edition
- The function setting bit for Synchronous Built–in Servo Motor DiS with
high-resolution serial output circuit H or C has been added.
3. Attachment
Attached 1 Addition of the function setting bit for Synchronous Built–in Servo Motor DiS with
TITLE
DRAW. No. CUST.
B-65270EN/07-007

Attached 1. Addition of the function setting bit for Synchronous Built–in
Servo Motor DiS with high-resolution serial output circuit H or C
(1) Outline
The function bit for 2048-magnification interpolation circuit has been supported to an analog output
type rotary encoder (using for Synchronous Built-in Servo Motor ), which connects with
high-resolution serial output circuit H （A860-0333-T701）or C（A860-0333-T801）.

90D0 series version U(21) and subsequent editions (Series 30i, 31i,)
(3) Parameters
Please use the function bit to an analog output type rotary encoder with 2n pulse per motor
revolution, when it connects with high-resolution serial output circuit H or C.
Both HP2048 and DD2048 bits need to be set to 1 in the case of using Synchronous Built-in Servo
Motor. And the setting value of FFG, position pulse and velocity pulse are same as the case of using
512-magnification interpolation circuit.
#7 #6 #5 #4 #3 #2 #1 #0
2274 (FS30i) DD2048 HP2048
HP2048(#0) The 2048-magnification interpolation circuit is
0: Not used
1: Used
DD2048(#6) For DiS motors, HP2048 is

0: Not available
1: Available
(Magnification to be used at parameter setting)

No.2274#6 No.2274#0 Interpolation magnification as high-resolution
serial output circuit H or circuit C is used
（DD2048）（HP2048）
DiS Motor LiS Motor
0 0 x 2048
x 2048
0 1
x 512
1 1 x 512
TITLE
DRAW. No. CUST.
B-65270EN/07-007

Please refer following table to set parameters for the rotary encoders, which have signal interval
4096 λ /rev, 8192λ /rev, 16384λ /rev and 32768 λ /rev, for DiS motor
Signal interval
4096 8192 16384 32768
Detection Detection Detection Detection Detection Detection Detection Detection

Symbol No. Unit Unit Unit Unit Unit Unit Unit Unit
0.001° 0.0001° 0.001° 0.0001° 0.001° 0.0001° 0.001° 0.0001°
DD2048 2274#6 1 1 1 1 1 1 1 1
HP2048 2274#0 1 1 1 1 1 1 1 1
LINEAR 2010#2 0 0 0 0 0 0 0 0
AMRDL 2112 0 0 0 0 0 0 0 0
AMR2 2138 0 0 -1 -1 -2 -2 -3 -3
PLC0 2000#0 0 0 0 0 1 1 1 1
AMR 2001 Poles/2 (binary) Poles/2 (binary) Poles/2 (binary) Poles/2 (binary)
PULCO 2023 8192 8192 16384 16384 3277 3277 6554 6554
PPLS 2024 12500 12500 25000 25000 5000 5000 10000 10000
REFCOUN
1821 360000 3600000 180000 1800000 90000 900000 360000 3600000
T
FFG 2084 9 90 9 90 9 90 9 90
FFG 2085 25 25 50 50 100 100 200 200
PSMPYL 2185 0 0 0 0 0 0 0 0
DECAMR 2220#0 0 0 0 0 0 0 0 0
800PLS#0 2275#0 0 0 0 0 0 0 1 1
TITLE
DRAW. No. CUST.
B-65270EN/07-007

Notice of the update of Digital Servo Software 90B5 & 90B6 series

Name FANUC AC SERVO MOTOR αi series,
PARAMETER MANUAL
Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Software 90B5 & 90B6 series
DRAW. No.
1 2008.07.10 B-65270EN/07-008
CUST.
01 Tang Newly designed
Design.
SHEET
Notice of the update of Digital Servo Software 90B5 & 90B6 series
.
1. Update Edition

90B5 06 FS0i –C, 0i Mate –C, FS20i–B
(with servo card equipped with 320C5410)
90B6 06 FS15i –B, 16i–B, 18i–B, 21i–B, 0i –B, 0i Mate –B,
Power Mate i –D, -H
- Changes of standard parameter table

3. Attached
TITLE
DRAW. No.
1 2008.07.10 B-65270EN/07-008
CUST.
Design.
SHEET

αiS300/2000 242 200V for HRV1
αiS22/6000 452 200V for HRV2,3
αiS22/6000HV 453 400V for HRV2,3
* Please refer to Table 1,2 about the standard parameters.
* So far, HRV1 control of αiS300/2000 uses motor ID number 115 (α300/2).
And motor ID number 242 for αiS300/2000 with HRV1 is officially supported from this edition.

βiS22/3000 213 200V for HRV1
βiS22/3000HV 214 400V for HRV1
βiS22/3000 313 200V for HRV2, 3
βiS22/3000HV 314 400V for HRV2, 3
* Please refer to Table1,2 about the standard parameters.
In order to improve stability, standard parameters of the following servo motors are changed.
αiF40/3000 207 200V for HRV1
αiF40/3000 FAN 208 400V for HRV1
αiF40/3000 307 200V for HRV2,3
αiF40/3000 FAN 308 400V for HRV2,3
TITLE
DRAW. No.
1 2008.07.10 B-65270EN/07-008
CUST.
Design.
SHEET
Table1) Standard paramter table for changes and new added models for HRV1 (Bordered parameters are changed.)
αiF40/3000 αiF40/3000 βiS22 βiS22 αiS300
Motor model
Fan 3000 3000HV 2000
Motor ID number 207 208 213 214 242
Symbol FS15i FS 16i, 18i, 20i, 21i, 0i, PMi
1808 2003 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00000000 00000000 00100000
1956 2012 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00001000 00001000 00000000
1708 2014 00000000 00000000 00001000 00001000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001110 00001110 00000000
2713 2300 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1289 1289 646 775 1357
PK2 1853 2041 -5048 -5048 -2486 -3580 -4212
PK3 1854 2042 -2696 -2696 -1298 -2663 -2710
PK1V 1855 2043 191 191 198 192 114
PK2V 1856 2044 -1712 -1712 -1766 -1722 -1023
PK3V 1857 2045 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 2216 2216 4297 4406 3709
BLCMP 1860 2048 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 3787
PHYST 1867 2055 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0
PVPA 1869 2057 -2570 -2570 -6174 -6174 -3850
PALPH 1870 2058 -2000 -2000 -2843 -2843 -800
PPBAS 1871 2059 0 0 0 0 0
TQLIM 1872 2060 7282 7282 5462 5462 7282
EMFLMT 1873 2061 0 0 0 0 0
POVC1 1877 2062 32511 32431 32520 32548 32391
POVC2 1878 2063 3215 4212 3097 2755 4714
TGALMLV 1892 2064 4 4 4 4 4
POVCLMT 1893 2065 9565 12545 9212 8192 23263
PK2VAUX 1894 2066 0 0 -10 -10 0
FILTER 1895 2067 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0
AALPH 1967 2074 8192 8192 8192 8192 12288
OSCTPL 1970 2077 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0
RTCURR 1979 2086 1957 2593 2121 2069 2483
TDPLD 1980 2087 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0
DBLIM 1995 2102 15000 15000 0 0 15000
ABVOF 1996 2103 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0
TRQCST 1998 2105 1839 1839 848 869 10871
LP24PA 1999 2106 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0
MGSTCM 1703 2110 1291 1291 1289 1289 16
DETQLM 1704 2111 5140 5140 7268 7268 1606
AMRDML 1705 2112 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0
NINTCT 1735 2127 3041 3041 1967 3894 0
MFWKCE 1736 2128 2000 2000 6000 6000 5500
MFWKBL 1752 2129 1553 1553 2315 2315 791
LP2GP 1753 2130 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0
PHDLY1 1756 2133 3087 3087 5647 5647 1556
PHDLY2 1757 2134 8990 8990 12820 12820 20494
DGCSMM 1782 2159 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0
OVCSTP 1784 2161 140 140 0 0 140
POVC21 1785 2162 32765 32718 32765 32765 32738
POVC22 1786 2163 33 629 40 38 375
POVCLMT2 1787 2164 6099 10707 7166 6815 13952
MAXCRT 1788 2165 165 165 85 45 365
TITLE
DRAW. No.
1 2008.07.10 B-65270EN/07-008
CUST.
Design.
SHEET
Table2) Standard paramter table for changes and new added models for HRV2,3 (Bordered parameters are changed.)
αiF40/3000 αiF40/3000 βiS22 βiS22 αiS22 αiS22
Motor model
Fan 3000 3000HV 6000 6000HV
Motor specification 0257 0257 0082 0083 0262 0263
Motor ID number 307 308 313 314 452 453
Symbol FS15i FS16i, 18i, 20i, 21i, 0i, PMi
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00100000 00100000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00001000 00001000 00000000 00000000
1708 2014 00000000 00000000 00001000 00001000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001110 00001110 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1500 1500 1157 1146 605 605
PK2 1853 2041 -8224 -8224 -5102 -5267 -2393 -2393
PK3 1854 2042 -1348 -1348 -1332 -1332 -1335 -1335
PK1V 1855 2043 191 191 198 192 102 102
PK2V 1856 2044 -1712 -1712 -1766 -1722 -914 -914
PK3V 1857 2045 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 2216 2216 4297 4406 4150 4150
BLCMP 1860 2048 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0
PVPA 1869 2057 -2570 -2570 -6174 -6174 -12039 -12039
PALPH 1870 2058 -2000 -2000 -2843 -2843 -2000 -2000
PPBAS 1871 2059 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 5462 5462 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0
POVC1 1877 2062 32511 32431 32520 32548 32511 32501
POVC2 1878 2063 3215 4212 3097 2755 3215 3332
TGALMLV 1892 2064 4 4 4 4 4 4
POVCLMT 1893 2065 9565 12545 9212 8192 9565 9912
PK2VAUX 1894 2066 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0
AALPH 1967 2074 0 0 12288 8192 4096 4096
OSCTPL 1970 2077 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0
RTCURR 1979 2086 1957 2593 2121 2069 1977 1977
TDPLD 1980 2087 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0
DBLIM 1995 2102 12000 12000 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0
TRQCST 1998 2105 1839 1839 848 869 819 819
LP24PA 1999 2106 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0
MGSTCM 1703 2110 1291 1291 1289 1289 1288 1288
DETQLM 1704 2111 5220 5140 7268 7268 12830 12830
AMRDML 1705 2112 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0
NINTCT 1735 2127 3041 3041 1967 3894 1000 2000
MFWKCE 1736 2128 6000 2000 6000 6000 1000 1000
MFWKBL 1752 2129 1560 1553 2315 2315 3854 3854
LP2GP 1753 2130 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0
PHDLY1 1756 2133 2590 3085 5647 5647 7690 7690
PHDLY2 1757 2134 8990 8990 12820 12820 8990 8990
DGCSMM 1782 2159 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0
OVCSTP 1784 2161 140 140 0 0 140 0
POVC21 1785 2162 32765 32718 32765 32765 32765 32765
POVC22 1786 2163 33 629 40 38 34 34
POVCLMT2 1787 2164 6099 10707 7166 6815 6222 6222
MAXCRT 1788 2165 165 165 85 45 165 85
TITLE
DRAW. No.
1 2008.07.10 B-65270EN/07-008
CUST.
Design.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/31i/32i ( 90E0)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Addition of the function setting bit for Add 2008.07
Synchronous Built–in Servo Motor DiS with
2. Addition of the function to drive Large Servo Add 2008.07
Motor with four windings
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
for Series 30i /31i /32i (90E0)
DRAW. No. CUST.
B-65270EN/07-009

Notice of the Update of Digital Servo Software for Series 30i/31i/32i ( 90E0)
1. Update Edition
- The function setting bit for Synchronous Built–in Servo Motor DiS with
high-resolution serial output circuit H or C has been added.
- The function to drive Large Servo Motor with four windings has been added
3. Attachment
Attached 1 Addition of the function setting bit for Synchronous Built–in Servo Motor DiS with
Attached 2 Addition of the function to drive Large Servo Motor with four windings
TITLE
DRAW. No. CUST.
B-65270EN/07-009

Attached 1. Addition of the function setting bit for Synchronous Built–in
Servo Motor DiS with high-resolution serial output circuit H or C
(1) Outline
The function bit for 2048-magnification interpolation circuit has been supported to an analog output
type rotary encoder (using for Synchronous Built-in Servo Motor ), which connects with
high-resolution serial output circuit H （A860-0333-T701）or C（A860-0333-T801）.

90E0 series version U(21) and subsequent editions (Series 30i, 31i, 32i )
(3) Parameters
Please use the function bit to an analog output type rotary encoder with 2n pulse per motor
revolution, when it connects with high-resolution serial output circuit H or C.
Both HP2048 and DD2048 bits need to be set to 1 in the case of using Synchronous Built-in Servo
Motor. And the setting value of FFG, position pulse and velocity pulse are same as the case of using
512-magnification interpolation circuit.
#7 #6 #5 #4 #3 #2 #1 #0
2274 (FS30i) DD2048 HP2048
HP2048(#0) The 2048-magnification interpolation circuit is
0: Not used
1: Used
DD2048(#6) For DiS motors, HP2048 is

0: Not available
1: Available
(Magnification to be used at parameter setting)

No.2274#6 No.2274#0 Interpolation magnification as high-resolution
serial output circuit H or circuit C is used
（DD2048）（HP2048）
DiS Motor LiS Motor
0 0 x 2048
x 2048
0 1
x 512
1 1 x 512
TITLE
DRAW. No. CUST.
B-65270EN/07-009

Please refer following table to set parameters for the rotary encoders, which have signal interval
4096 λ /rev, 8192λ /rev, 16384λ /rev and 32768 λ /rev, for DiS motor
Signal interval
4096 8192 16384 32768
Detection Detection Detection Detection Detection Detection Detection Detection

Symbol No. Unit Unit Unit Unit Unit Unit Unit Unit
0.001° 0.0001° 0.001° 0.0001° 0.001° 0.0001° 0.001° 0.0001°
DD2048 2274#6 1 1 1 1 1 1 1 1
HP2048 2274#0 1 1 1 1 1 1 1 1
LINEAR 2010#2 0 0 0 0 0 0 0 0
AMRDL 2112 0 0 0 0 0 0 0 0
AMR2 2138 0 0 -1 -1 -2 -2 -3 -3
PLC0 2000#0 0 0 0 0 1 1 1 1
AMR 2001 Poles/2 (binary) Poles/2 (binary) Poles/2 (binary) Poles/2 (binary)
PULCO 2023 8192 8192 16384 16384 3277 3277 6554 6554
PPLS 2024 12500 12500 25000 25000 5000 5000 10000 10000
REFCOUN
1821 360000 3600000 180000 1800000 90000 900000 360000 3600000
T
FFG 2084 9 90 9 90 9 90 9 90
FFG 2085 25 25 50 50 100 100 200 200
PSMPYL 2185 0 0 0 0 0 0 0 0
DECAMR 2220#0 0 0 0 0 0 0 0 0
800PLS#0 2275#0 0 0 0 0 0 0 1 1
TITLE
DRAW. No. CUST.
B-65270EN/07-009

Attached2. Addition of the function to drive Large Servo Motor with
four windings
(1) Outline
The following Large Servo Motors, which have four windings, are available.
PDM (PWM Distribution Module)can not be used in 30i series CNCs. For the CNCs, you can drive the
motors by setting the following parameters. Tandem Control Option (J733) is necessary to use
following setting.
Motor model Servo Amplifier Motor number Remarks
αiS2000/2000HV 360HV×4 459 4 ampilefiers drive
αiS3000/2000HV 360HV×4 460 4 ampilefiers drive
(2) Servi series / edition

90E0 series / edition U(21) or later
(3) Parameters setting
New parameter
#7 #6 #5 #4 #3 #2 #1 #0
2211(FS30i) PLW4
PLW4(#7) Large Servo Motor with four windings is

0: Not used
1: Used
Note) If you change this bit, you must turn CNC off.
Note) This function bit is included in the standard parameter table for above motors.
(after this software edition)
Note) Sequent 4 numbers are necessary in No.1023 setting to drive one motor. You
must set this function bit for 4 axes.
(Example) No.1023 = from 1 to 4, from 5 to 8, from 13 to 16, from 17 to 20, or
from 21 to 24.
Note) You can not use HRV3 or HRV4 at driving these motors.
Note) You need not set No.2018#7(Motor Feedback Sharing Function) and
No.2200#1(Full-closed Feedback Sharing Function).
Related parameter
2022(FS30i) Direction of motor rotation
Note) You must set same value for Large Servo Motor with four windings.
111: Clockwise as viewed from the Pulsecoder
-111: Counterclockwise as viewed from the Pulsecoder
TITLE
DRAW. No. CUST.
B-65270EN/07-009

(4) Cable connection and parameter setting example
(Example) Large Servo Motor with four windings is used as full-closed axis.
PS1 SV1 SV2 PS2 SV3 SV4 SDU
FSSB
Power cables
FB cable
X1 (Main axis) X2 (Sub axis) X3 (Sub axis) X4 (Sub axis)

No.1023 1 2 3 4
No.1815#1 1 - - -
No.1905#6 1 - - -
No.14340 - 0 1 2 3
No.14376 - 0 - - -
No.2211#7 1 1 1 1
(Note) In semi-closed axis, you need not set gray hatching part.
(Note) You must set 4n+1, 4n+2, 4n+3, 4n+4 for No.1023. The axis, which has 4n+1 as No.1023
setting, is main axis and others are sub axes.
(5) Illegal Servo Parameter Setting

In the following case, Illegal Servo Parameter Setting Alarm will happen.
(Detail DGN352 = 2113)
• Without Tandem Contorl Option (Detail DGN will not be displayed in this case.)
• The settings of No.2211#7 of 4 axes are not all 1.
• Motor number (No.2020) of 4 axes are not all same value.
• HRV3 is used (No.2013#0=1 ).
(6) Others
1) Position control is done only by main axis, and you don’t give any position command to sub axes.
2) Basically you set same parameter values for main and sub axes.
3) You should input Detach signal to all axes (main and sub) when you use Detach function.
4) You should set the same parameters for Resonance Elimination Filter to all axes (main and sub),
when you use the filters.
5) You can measure frequency response of velocity loop only by specifying main axis as
measuremnet target in SERVO GUIDE.
TITLE
DRAW. No. CUST.
B-65270EN/07-009

Attached：Table1：Standrard parameters for Large motor αiS2000/2000HV and αiS 3000/2000HV
Motor model αiS2000 αiS3000
2000HV 2000HV
Motor specification 0091 0092
Symbol FS30i,31i,
2003 00001000 00001000
2004 01000011 01000011
2005 00000000 00000000
2006 00000000 00000000
2007 00100000 00100000
2008 00000000 00000000
2009 00000000 00000000
2010 00000000 00000000
2011 00000000 00000000
2012 00000000 00000000
2013 00000000 00000000
2014 00000000 00000000
2210 00000000 00000000
2211 10011110 10011010
2300 00000000 00000000
2301 00000000 00000000
PK1 2040 643 772
PK2 2041 -3600 -3819
PK3 2042 -1358 -1357
PK1V 2043 502 652
PK2V 2044 -4500 -5836
PK3V 2045 0 0
PK4V 2046 -8235 -8235
POA1 2047 843 650
BLCMP 2048 0 0
DPFMX 2049 0 0
POK1 2050 956 956
POK2 2051 510 510
RESERV 2052 0 0
PPMAX 2053 21 21
PDDP 2054 3787 3787
PHYST 2055 319 319
EMFCMP 2056 0 0
PVPA 2057 -3363 -2088
PALPH 2058 -3200 -5000
PPBAS 2059 0 0
TQLIM 2060 7282 7282
EMFLMT 2061 0 0
POVC1 2062 32309 32309
POVC2 2063 5734 5734
TGALMLV 2064 4 4
POVCLMT 2065 27346 27346
PK2VAUX 2066 0 0
FILTER 2067 0 0
FALPH 2068 0 0
VFFLT 2069 0 0
ERBLM 2070 0 0
PBLCT 2071 0 0
SFCCML 2072 0 0
PSPTL 2073 0 0
AALPH 2074 12288 12288
OSCTPL 2077 0 0
PDPCH 2078 0 0
PDPCL 2079 0 0
DPFEX 2080 0 0
DPFZW 2081 0 0
BLENDL 2082 0 0
MOFCTL 2083 0 0
RTCURR 2086 2893 3187
TDPLD 2087 0 0
MCNFB 2088 0 0
BLBSL 2089 0 0
ROBSTL 2090 0 0
ACCSPL 2091 0 0
ADFF1 2092 0 0
VMPK3V 2093 0 0
BLCMP2 2094 0 0
AHDRTL 2095 0 0
RADUSL 2096 0 0
SMCNT 2097 0 0
DEPVPL 2098 0 0
ONEPSL 2099 400 400
INPA1 2100 0 0
INPA2 2101 0 0
DBLIM 2102 0 0
ABVOF 2103 0 0
ABTSH 2104 0 0
TRQCST 2105 6221 8472
LP24PA 2106 0 0
VLGOVR 2107 0 0
RESERV 2108 0 0
BELLTC 2109 0 0
MGSTCM 2110 784 267
DETQLM 2111 1510 2218
AMRDML 2112 0 0
NFILT 2113 0 0
NINTCT 2127 3449 3029
MFWKCE 2128 3000 2700
MFWKBL 2129 1291 777
LP2GP 2130 0 0
LP4GP 2131 0 0
LP6GP 2132 0 0
PHDLY1 2133 2060 2068
PHDLY2 2134 6420 6410
DGCSMM 2159 0 0
TRQCUP 2160 0 0
OVCSTP 2161 140 140
POVC21 2162 32745 32745
POVC22 2163 292 292
POVCLMT2 2164 13952 13952
MAXCRT 2165 365 365
TITLE
DRAW. No. CUST.
B-65270EN/07-009

Notice of the Update of Digital Servo Software for Series 15i, 16i, 18i, 21i, PMi-D, PMi-H (90BP )

PARAMETER MANUAL

Correct, Del Date
Basic Function Changes of Standard Parameter Table Add 2008.09
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Notice of the Update of Digital Servo Software for

Series 15i, 16i, 18i, 21i, PMi -D, PMi -H ( 90BP)
DRAW. No. CUST.
B-65270EN/07-010

Notice of the Update of Digital Servo Software for Series 15i, 16i, 18i, 21i, PMi -D, PMi -H ( 90BP)
1. Update Edition
90BP 04 FS15i, 16i, 18i, 21i, PMi -D, PMi –H
- Changes of Standard Parameter Table

3. Attached
TITLE

DRAW. No. CUST.
B-65270EN/07-010


(Series 15i, 16i, 18i, 21i, PMi -D, PMi -H)
Series 90BP/D(04) and subsequent editions
Soft thermal(OVC) alarm level for the following servo motors are optimized.
HRV1 HRV2,3
Motor Model Motor ID No. Motor ID No.
αiF 30/3000 203 303
αiF 40/3000 207 307
αiF 40/3000Fan 208 308
αiS 22/4000 215 315
αiS 30/4000 218 318
αiS 40/4000 222 322
αiS 22/6000 - 452
* Please refer to Table1, 2 about the standard parameters.
Standard parameters of the following Large Servo Motor are added. With these parameters, the
optimal control can be done by making use of DC link voltage information, and heat generation at
high-speed rotation can be reduced.

αiS1000/2000HV
458 400V
（A06B-0098-B010）
To apply the parameters, the following conditions on servo software, servo amplifier, and power supply module
must be fulfilled.
<Condition>
Servo software: Series 90BP/D(4) and subsequent editions
Servo amplifier: A06B-6127-H109 (αi SV-360HV)
Power supply module: A06B-6150-H100 (αi PS-100HV)
<Notice>
Parameter auto loading can be executed by Motor ID No. 458 for 90BP/D(04) and subsequent
editions.
αiS1000/2000HV (A06B-0098-B010) is upper compatible with the previous motor αiS1000/2000HV
(A06B-0298-B010).
Do not use the parameters specified by Motor ID No.458 to the old model αiS1000/2000HV
(A06B-0298-B010).
TITLE

DRAW. No. CUST.
B-65270EN/07-010

Table1) Standard parameter table for changes models (Checked parameters are changed.) (HRV1)
αiF30 αiF40 αiF40 αiS22 αiS30 αiS40

Motor model
3000 3000 3000Fan 4000 4000 4000
Motor ID number 203 207 208 215 218 222
Symbol FS15i FS16i,18i,21i,PMi
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 597 1289 1289 714 689 748
PK2 1853 2041 -2334 -5048 -5048 -2904 -2675 -3055
PK3 1854 2042 -2694 -2696 -2696 -2674 -2683 -2682
PK1V 1855 2043 230 191 191 69 82 92
PK2V 1856 2044 -2057 -1712 -1712 -616 -733 -827
PK3V 1857 2045 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 1845 2216 2216 6163 5175 4589
BLCMP 1860 2048 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0
PVPA 1869 2057 -5170 -2570 -2570 -7689 -6415 -5648
PALPH 1870 2058 -1000 -2000 -2000 -2000 -3000 -3000
PPBAS 1871 2059 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0
POVC1 1877 2062 32515 32515 32431 32515 32515 32515
POVC2 1878 2063 3166 3166 4212 3166 3166 3166
TGALMLV 1892 2064 4 4 4 4 4 4
POVCLMT 1893 2065 9418 9418 12545 9418 9418 9418
PK2VAUX 1894 2066 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0
AALPH 1967 2074 8192 8192 8192 4096 4096 4096
OSCTPL 1970 2077 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0
RTCURR 1979 2086 2306 1957 2593 1627 1836 2073
TDPLD 1980 2087 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0
DBLIM 1995 2102 0 15000 15000 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0
TRQCST 1998 2105 1170 1839 1839 1216 1470 1701
LP24PA 1999 2106 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0
MGSTCM 1703 2110 1032 1291 1291 519 775 776
DETQLM 1704 2111 7735 5140 5140 6224 6450 5682
AMRDML 1705 2112 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0
NINTCT 1735 2127 1688 3041 3041 2041 1871 1853
MFWKCE 1736 2128 2500 2000 2000 2500 4000 4000
MFWKBL 1752 2129 2829 1553 1553 2580 2574 2063
LP2GP 1753 2130 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0
PHDLY1 1756 2133 5140 3087 3087 5150 5150 5150
PHDLY2 1757 2134 8995 8990 8990 8990 8990 8988
DGCSMM 1782 2159 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0
OVCSTP 1784 2161 128 128 128 128 128 128
POVC21 1785 2162 32764 32764 32717 32766 32765 32765
POVC22 1786 2163 48 46 637 28 37 38
POVCLMT2 1787 2164 8124 8124 10815 5177 6687 6846
MAXCRT 1788 2165 165 165 165 165 165 165
ACCBSLM 2717 2304 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0 0
DCIDBS 2723 2310 0 0 0 0 0 0
TITLE

DRAW. No. CUST.
B-65270EN/07-010

Table2) Standard parameter table for changes and new added models (Checked parameters are changed.) ( HRV2,HRV3)
αiF30 αiF40 αiF40 αiS22 αiS30 αiS40 αiS22 αiS1000
Motor model
3000 3000 3000Fan 4000 4000 4000 6000 2000HV
Motor ID number 303 307 308 315 318 322 452 458
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00011010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 768 1500 1500 581 799 712 605 1260
PK2 1853 2041 -4492 -8224 -8224 -3844 -4447 -4138 -2393 -8010
PK3 1854 2042 -1347 -1348 -1348 -1337 -1317 -1341 -1335 -1362
PK1V 1855 2043 230 191 191 69 82 92 102 263
PK2V 1856 2044 -2057 -1712 -1712 -616 -733 -827 -914 -2357
PK3V 1857 2045 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 1845 2216 2216 6163 5175 4589 4150 1610
BLCMP 1860 2048 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 3787
PHYST 1867 2055 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -20500 0 0 0 0 0 0 0
PVPA 1869 2057 -8465 -2570 -2570 -7687 -6412 -5645 -12039 -2320
PALPH 1870 2058 -1657 -2000 -2000 -2000 -2300 -3000 -2000 -2500
PPBAS 1871 2059 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0
POVC1 1877 2062 32515 32515 32431 32515 32515 32515 32515 32309
POVC2 1878 2063 3166 3166 4212 3166 3166 3166 3166 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 9418 9418 12545 9418 9418 9418 9418 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0
AALPH 1967 2074 4096 0 0 4096 4096 4096 4096 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2306 1957 2593 1627 1836 2073 1977 2960
TDPLD 1980 2087 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 12000 12000 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1170 1839 1839 1216 1470 1701 819 27963
LP24PA 1999 2106 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1032 1291 1291 519 775 776 1288 785
DETQLM 1704 2111 7735 5220 5140 6224 6450 5682 12830 2300
AMRDML 1705 2112 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1688 3041 3041 2041 1871 1853 1000 11851
MFWKCE 1736 2128 2500 6000 2000 2500 4000 4000 1000 4500
MFWKBL 1752 2129 2829 1560 1553 2580 2574 2063 3854 1038
LP2GP 1753 2130 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 5140 2590 3085 5150 5150 5150 7690 2570
PHDLY2 1757 2134 8995 8990 8990 8990 8990 8988 8990 12810
DGCSMM 1782 2159 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 128 128 128 128 128 128 128 140
POVC21 1785 2162 32764 32764 32717 32766 32765 32765 32765 32745
POVC22 1786 2163 48 46 637 28 37 38 44 292
POVCLMT2 1787 2164 8124 8124 10815 5177 6687 6846 7743 13952
MAXCRT 1788 2165 165 165 165 165 165 165 165 365
ACCBSLM 2717 2304 0 0 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0 0 0 22
DCIDBS 2723 2310 0 0 0 0 0 0 0 1112
TITLE

DRAW. No. CUST.
B-65270EN/07-010

Notice of the Update of Digital Servo Software for Series 30i, 31i, 32i (90E0)

PARAMETER MANUAL

Correct, Del Date
Basic Function Changes of Standard Parameter Table Add 2008.10
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-011

1. Update Edition
90E0 23 FS30i, 31i, 32i (For HRV2 and HRV3 control)

3. Attached
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-011


Series 90E0/W(23) and subsequent editions
Motor Model Motor ID No.

αiF 30/3000 303
αiF 40/3000 307
αiF 40/3000Fan 308
αiS 22/4000 315
αiS 30/4000 318
αiS 40/4000 322
αiS 22/6000 452
* Please refer to Table1 about the standard parameters.

αiS1000/2000HV
458 400V
（A06B-0098-B010）
must be fulfilled.
<Condition>
Servo software: Series 90E0/W(23) and subsequent editions
<Notice>
Parameter auto loading can be executed by Motor ID No. 458 for 90E0/W(23) and subsequent
editions.
(A06B-0298-B010).
(A06B-0298-B010).
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-011

Table1) Standard parameter table for changes and new added models (Checked parameters are changed.) (HRV2,HRV3)
Motor model
3000 3000 3000Fan 4000 4000 4000 6000 2000HV
Motor ID number 303 307 308 315 318 322 452 458
Symbol FS16i,18i,21i,PMi
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00011010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 768 1500 1500 581 799 712 605 1260
PK2 2041 -4492 -8224 -8224 -3844 -4447 -4138 -2393 -8010
PK3 2042 -1347 -1348 -1348 -1337 -1317 -1341 -1335 -1362
PK1V 2043 230 191 191 69 82 92 102 263
PK2V 2044 -2057 -1712 -1712 -616 -733 -827 -914 -2357
PK3V 2045 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 1845 2216 2216 6163 5175 4589 4150 1610
BLCMP 2048 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 3787
PHYST 2055 319 319 319 319 319 319 319 319
EMFCMP 2056 -20500 0 0 0 0 0 0 0
PVPA 2057 -8465 -2570 -2570 -7687 -6412 -5645 -12039 -2320
PALPH 2058 -1657 -2000 -2000 -2000 -2300 -3000 -2000 -2500
PPBAS 2059 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0
POVC1 2062 32515 32515 32431 32515 32515 32515 32515 32309
POVC2 2063 3166 3166 4212 3166 3166 3166 3166 5734
TGALMLV 2064 4 4 4 4 4 4 4 4
POVCLMT 2065 9418 9418 12545 9418 9418 9418 9418 27346
PK2VAUX 2066 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0
AALPH 2074 4096 0 0 4096 4096 4096 4096 12288
OSCTPL 2077 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0
RTCURR 2086 2306 1957 2593 1627 1836 2073 1977 2960
TDPLD 2087 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0
DBLIM 2102 0 12000 12000 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0
TRQCST 2105 1170 1839 1839 1216 1470 1701 819 27963
LP24PA 2106 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0
MGSTCM 2110 1032 1291 1291 519 775 776 1288 785
DETQLM 2111 7735 5220 5140 6224 6450 5682 12830 2300
AMRDML 2112 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0
NINTCT 2127 1688 3041 3041 2041 1871 1853 1000 11851
MFWKCE 2128 2500 6000 2000 2500 4000 4000 1000 4500
MFWKBL 2129 2829 1560 1553 2580 2574 2063 3854 1038
LP2GP 2130 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0
PHDLY1 2133 5140 2590 3085 5150 5150 5150 7690 2570
PHDLY2 2134 8995 8990 8990 8990 8990 8988 8990 12810
DGCSMM 2159 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0
OVCSTP 2161 128 128 128 128 128 128 128 140
POVC21 2162 32764 32764 32717 32766 32765 32765 32765 32745
POVC22 2163 48 46 637 28 37 38 44 292
POVCLMT2 2164 8124 8124 10815 5177 6687 6846 7743 13952
MAXCRT 2165 165 165 165 165 165 165 165 365
ACCBSLM 2304 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0 22
DCIDBS 2310 0 0 0 0 0 0 0 1112
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-011

Correction of the description about the setting for DiS motor with Heidenhain’s encoder

PARAMETER MANUAL

Correct, Del Date
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction Description about the setting for DiS motor with Correct 2008.11
Heidenhain’s encoder
Another
TITLE
Correction of the description about the
setting for DiS motor with Heidenhain’s
encoder
DRAW. No. CUST.
B-65270EN/07-012

Correction of the description about the setting for DiS motor with Heidenhain’s encoder
We inform you that there is a mistake in the description of the following table.
[Before correction] Table 4.15.1 (m) For RCN223, RCN723, or RCN727

Symbol
Detection unit Detection unit
name FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 -4 -4
PLC0 2000#0 1804#0 1 1
Parameter No.2001
Number of Number of
is incorrect in this AMR 2001 1806
table.
PULCO 2023 1876 6554 6554
PPLS 2024 1891 10000 10000
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 9 9
FFG 2085 1978 200 20
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
800PLS#0 2275#0 2688#0 1 1
800PLS#1 2275#1 2688#1 1 1
DMASK 2394 2807 8 8
Table 4.15.1 (m) For RCN223, RCN723, or RCN727
[After correction]
Symbol
Detection unit Detection unit
name FS30i,16i FS15i
1/1000deg 1/10000deg
AMRDL 2112 1705 0 0
AMR2 2138 1761 -4 -4
PLC0 2000#0 1804#0 1 1
This is the correct
Number of Number of
setting. AMR 2001 1806
poles (binary) poles (binary)
PULCO 2023 1876 6554 6554
PPLS 2024 1891 10000 10000
REFCOUNT 1821 1896 360000 3600000
FFG 2084 1977 9 9
FFG 2085 1978 200 20
PSMPYL 2185 2628 0 0
DECAMR 2220#0 2608#0 0 0
800PLS#0 2275#0 2688#0 1 1
800PLS#1 2275#1 2688#1 1 1
DMASK 2394 2807 8 8
TITLE
Correction of the description about the
setting for DiS motor with Heidenhain’s
encoder
DRAW. No. CUST.
B-65270EN/07-012


PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Motor control stop judgment in quick stop at Add 2009.02
emergency stop has been added.
2.DI signal to invalidate Integrator copy function has
Add 2009.02
been added.
3.Preload function with time constant has been added. Add 2009.02
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

1. Update Edition
90E0 25 FS30i, 31i, 32i (For HRV2 and HRV3 control)
- Motor control stop judgment in quick stop at emergency stop has been added.
- DI signal to invalidate Integrator copy function has been added.
- Preload function with time constant has been added.
3. Attached
Attached 1 About an addition of Motor control stop judgment in quick stop at emergency stop
Attached 2 About DI signal to invalidate Integrator copy function
Attached 3 Improvement of Preload function (Addition of time constant)
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

- Attached 1. About an addition of Motor control stop judgment in quick
stop at emergency stop
(1) Summary
When Large Spindle Motor like αiS2000/2000HV is used in the axis of rotation of a large lathe, there
are some cases where it takes several seconds or more to stop rotation even if it uses maximum torque
because of its large inertia.
When qiuck stop at emergency stop is applied to such an axis, timer setting for an emergency stop
signal needs to be set more than several seconds in order to secure the time of control stop. Since it is
difficult to estimate the time correctly and longer time has to be set as a result, this function has been
added to make ampilifier MCC off just after the motor stop has been added.
When emergency stop occurs, motor is
decelerated by control and the amplifier
Actual Speed
MCC will be turned off, as soon as motor
stop.
A motor stop state is judged by SVSSTn
signal.
Emergency stop
signal
　SVSSTn
Timer setting value for Quick
Stop at Emergency Stop
Amplifier Mcc off
(2) Servo software Series / edition

Series 90E0 / Y(25) and subsequent editions in Series-30i/31i/32i
Following system software is needed for this function.
(System soft)
[ FS30i -A ]
G002, G012, G022, G032 / 48.0 and subsequent editions
G00B, G01B, G02B, G03B / 48. and subsequent editions
G003, G013, G023, G033 / 31.0 and subsequent editions
G00C, G01C, G02C, G03C / 31.0 and subsequent editions
[ FS31i -A5 ]
G121, G131 / 48.0 and subsequent editions
G12B, G13B / 48.0 and subsequent editions
G12C, G13C / 31.0 and subsequent editions
[ FS31i -A ]
[ FS32i-A ]
G201 / 48.0 and subsequent editions
G203 / 31.0 and subsequent editions
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

(3) Parameters
New parameter
#7 #6 #5 #4 #3 #2 #1 #0
No.2294(FS30i) SSTMCC
SSTMC (#4) During qiuck stop at emergency stop, function to cut off amplifier MCC just
after motor stop is
0: Used
1: Not used ← Use this setting.
Because the above function cut off amplifier’s MCC when a motor stop state is detected, it needs to
judge whether motor stops or not .
Therefore, the following detection level of speed zero parameter needs to be set.
No.2483 (FS30i) Detection level of speed zero (SSTLV)

Please specify the revolution speed(1/min) that is judged to be stopping in
detection level of zero speed. When the actual speed becomes lower than detection
level of zero speed, motor is judged to be stopping, and Zero-speed detecting signal,
SVSSTn becomes “1”.
In order to set the timer more than several seconds to Quick stop function at emergency stop, not
only the break control timer but also emergency stop signal timer of αiPS need to be extended.
Because the maximum setting to emergency stop signal timer in αiPs is 400ms, if you want to
delay motor deactivation more, please add an outside timer.
(For details please refer to B-65270EN/07 4.10 BRAKE CONTROL FUNCTION and 4.11
QUICK STOP FUNCTION).
No.2083 (FS30i) Brake control timer

[Unit of data] ms
[Recommended value] 0 to 32000 ms
#7 #6 #5 #4 #3 #2 #1 #0
No.2210 (FS30i) ESPTM1 ESPTM0
Emergency stop timer built into the amplifier
0 0 50ms (default value)

0 1 100ms
1 0 200ms
1 1 400ms
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

- Attached 2. About DI signal to invalidate Integrator copy function
(1) Summary
When you drive two axes with synchronous control, vibration between master and slave axes or
problem of heat generation by pulling each other might be caused by a slight difference of
characteristics. In order to solve these problems, there is the velocity loop integrator copy function that
copies the velocity loop integrator from master axis to slave axis, thereby preventing above
phenomena.
There are some machines that need to switch off/on synchronous control dynamically. They use
synchronous control when two axes need to move synchronously , and they don’t use it when two axes
need to move separately. The integrator copy function has not been able to be applied to such machines,
because it always copies the velocity loop integrator from master axis to slave axis.
This time, we have added a specification that makes Integrator copy function invalidated by DI
signal.
Velocity feedback
Master axis
Proportional gain
- +
VCMD + + TCMD
∑ Integral gain
G0321
1
Slave axis
0
+
∑ Integral gain
+
VCMD TCMD
- +
Proportional gain
Velocity feedback
(2) Servo software Series / edition

Series 90E0 / Y(25) and subsequent editions
(3) Parameters
New parameter
#7 #6 #5 #4 #3 #2 #1 #0
2286 (FS30i) WCCNCK
WCCNCK(#4) DI signal to invalidate integrator copy is
0: Used
1: Not used
(Specify only the slave axis)
When WCCNCK=1, the integrator copy function can be turned OFF/ON dynamically by DI
signal G0321.
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

Existing parameter
#7 #6 #5 #4 #3 #2 #1 #0
2273 (FS30i) WSVCP
WSVCP(#1) Integrator copy function is
0: Not used
1: Used
The integrator of the master axis is copied to the slave axis.
(4) Signals
Connection status flag
SVDI21～SVDI28
[Function] This signal invalidates servo fucntions to make two axes that use synchronous
control stable (unconnected) and enables independent operation
[Operation] When 1 is set in this signal, the status of two axes becomes “unconnected”.
When the signal is 0, the status becomes “connected”.
Signal address
#7 #6 #5 #4 #3 #2 #1 #0
G0321 SVDI28 SVDI27 SVDI26 SVDI25 SVDI24 SVDI23 SVDI22 SVDI21
SVDI21～SVDI28:Connection status flag
0: The status of two axes is “Connected” (Two axes move synchronously.)
1: The status of two axes is “Unconnected” (Two axes move independently.)
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

Attached 3. Improvement of Preload function (Addition of time constant)
(1) Summary
In Tandem control, there is a Preload function as a function to absorb the effect of backlash between
Main and Sub axes by giving offset torque of a reverse direction for the two motors.
Because the present Preload function has been added by time constant 0, there is a possibility that a
shock occurs at a moment of excitation. In ordet to reduce this shock, Preload function with
exponential time constant has been added.
\(2) Servo software Series / edition

Series 90E0 / Y(25) and subsequent editions in Series-30i/31i/32i
Series 90E3 / D(04) and subsequent editions in Series-30i/31i/32i for Learning control.
(3) Parameters
New parameter
#7 #6 #5 #4 #3 #2 #1 #0
No.2417(FS30i) TIMCAL TIMPR2
TIMCAL (#4) Preload function with expoenential time constant is

0: Not used
1: Used
This exponential time constant is decided by the reciprocal number of Position

loop gain (No.1825).
For exmaple, in case of No.1825 = 3000(30 s-1), preload is added with
exponential time constant (1/Pg = 33.3ms) from the moment when amplifier
becomes ENBL.
Note
Please don’t use this constant in case that of torque offset canseling function
(No2215#1) under Unexpected Disturbance Torque Detection function is using.
TIMPR2 (#2) Exponential time constant of Preload function is

0: the reciprocal number of Position loop gain (No.1825)
1: 4 times of the reciprocal number of Position loop gain (No.1825)
In some machine, there is a possibility that time constant is not enough and
mechanical shock occurs. In this case, time constant can be extended by setting
this bit.
Existing parameter
No.2087 (FS30i) Preload

[Valid data range] from -1000 to 1000
[Unit of data] TCMD unit
[Recommend value] Maximun value is recommended about one third of rated torque.
In order to absorb the effect of backlash between main axis and sub axis, torque of reverse
polality is added.
TITLE
Series 30i, 31i, 32i (90E0)
DRAW. No. CUST.
B-65270EN/07-013

Notice of the update of Digital Servo Software for Series 0i/16i /18i /21i etc. (90B8/M,
90B1/M )

LINEAR MOTOR LiS series
SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series
PARAMETER MANUAL
Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
(90B8/M, 90B1/M)
DRAW. No.
1 2009.03.04 B-65270EN/07-014
CUST.
Design.
SHEET
Notice of the update of Digital Servo Software for Series 0i/16i/18i/21i etc.
(90B8/M, 90B1/M)
.
1. Update Edition

90B8 13 FS0i-C, FS0iMate-C
- Changes of Standard parameter table

3. Attached
Attached 1 Changes of Standard parameter table
TITLE
(90B8/M, 90B1/M)
DRAW. No.
1 2009.03.04 B-65270EN/07-014
CUST.
Design.
SHEET
Attached 1. Changes of Standard parameter table
HRV1 HRV2,3
Motor Model Motor ID No. Motor ID No.
αiF 30/3000 203 303
αiF 40/3000 207 307
αiF 40/3000Fan 208 308
αiS 22/4000 215 315
αiS 30/4000 218 318
αiS 40/4000 222 322
αiS 22/6000 - 452

αiS1000/2000HV
458 400V
（A06B-0098-B010）
must be fulfilled.
<Condition>
Servo software: Series 90B1/M(13), 90B8/M(13) and subsequent editions
<Notice>
Parameter auto loading can be executed by Motor ID No. 458 for 90B1/M(13), 90B8/M(13) and
(A06B-0298-B010).
(A06B-0298-B010).
TITLE
(90B8/M, 90B1/M)
DRAW. No.
1 2009.03.04 B-65270EN/07-014
CUST.
Design.
SHEET
Table1) Standard parameter table for changes models (Checked parameters are changed.) (HRV1)
αiF30 αiF40 αiF40 αiS22 αiS30 αiS40
Motor model
3000 3000 3000Fan 4000 4000 4000
Motor ID number 203 207 208 215 218 222
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000110 00000110 00000110 00000110 00000110 00000110
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 597 1289 1289 714 689 748
PK2 1853 2041 -2334 -5048 -5048 -2904 -2675 -3055
PK3 1854 2042 -2694 -2696 -2696 -2674 -2683 -2682
PK1V 1855 2043 230 191 191 69 82 92
PK2V 1856 2044 -2057 -1712 -1712 -616 -733 -827
PK3V 1857 2045 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 1845 2216 2216 6163 5175 4589
BLCMP 1860 2048 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0
PVPA 1869 2057 -5170 -2570 -2570 -7689 -6415 -5648
PALPH 1870 2058 -1000 -2000 -2000 -2000 -3000 -3000
PPBAS 1871 2059 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0
POVC1 1877 2062 32515 32515 32431 32515 32515 32515
POVC2 1878 2063 3166 3166 4212 3166 3166 3166
TGALMLV 1892 2064 4 4 4 4 4 4
POVCLMT 1893 2065 9418 9418 12545 9418 9418 9418
PK2VAUX 1894 2066 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0
AALPH 1967 2074 8192 8192 8192 4096 4096 4096
OSCTPL 1970 2077 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0
RTCURR 1979 2086 2306 1957 2593 1627 1836 2073
TDPLD 1980 2087 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0
DBLIM 1995 2102 0 15000 15000 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0
TRQCST 1998 2105 1170 1839 1839 1216 1470 1701
LP24PA 1999 2106 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0
MGSTCM 1703 2110 1032 1291 1291 519 775 776
DETQLM 1704 2111 7735 5140 5140 6224 6450 5682
AMRDML 1705 2112 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0
NINTCT 1735 2127 1688 3041 3041 2041 1871 1853
MFWKCE 1736 2128 2500 2000 2000 2500 4000 4000
MFWKBL 1752 2129 2829 1553 1553 2580 2574 2063
LP2GP 1753 2130 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0
PHDLY1 1756 2133 5140 3087 3087 5150 5150 5150
PHDLY2 1757 2134 8995 8990 8990 8990 8990 8988
DGCSMM 1782 2159 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0
OVCSTP 1784 2161 128 128 128 128 128 128
POVC21 1785 2162 32764 32764 32717 32766 32765 32765
POVC22 1786 2163 48 46 637 28 37 38
POVCLMT2 1787 2164 8124 8124 10815 5177 6687 6846
MAXCRT 1788 2165 165 165 165 165 165 165
ACCBSLM 2717 2304 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0 0
DCIDBS 2723 2310 0 0 0 0 0 0
TITLE
(90B8/M, 90B1/M)
DRAW. No.
1 2009.03.04 B-65270EN/07-014
CUST.
Design.
SHEET
Table2) Standard parameter table for changes and new added models (Checked parameters are changed.) ( HRV2,HRV3)
Motor model
3000 3000 3000Fan 4000 4000 4000 6000 2000HV
Motor ID number 303 307 308 315 318 322 452 458
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00011010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 768 1500 1500 581 799 712 605 1260
PK2 1853 2041 -4492 -8224 -8224 -3844 -4447 -4138 -2393 -8010
PK3 1854 2042 -1347 -1348 -1348 -1337 -1317 -1341 -1335 -1362
PK1V 1855 2043 230 191 191 69 82 92 102 263
PK2V 1856 2044 -2057 -1712 -1712 -616 -733 -827 -914 -2357
PK3V 1857 2045 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 1845 2216 2216 6163 5175 4589 4150 1610
BLCMP 1860 2048 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894 3787
PHYST 1867 2055 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 -20500 0 0 0 0 0 0 0
PVPA 1869 2057 -8465 -2570 -2570 -7687 -6412 -5645 -12039 -2320
PALPH 1870 2058 -1657 -2000 -2000 -2000 -2300 -3000 -2000 -2500
PPBAS 1871 2059 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0
POVC1 1877 2062 32515 32515 32431 32515 32515 32515 32515 32309
POVC2 1878 2063 3166 3166 4212 3166 3166 3166 3166 5734
TGALMLV 1892 2064 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 9418 9418 12545 9418 9418 9418 9418 27346
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0
AALPH 1967 2074 4096 0 0 4096 4096 4096 4096 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0
RTCURR 1979 2086 2306 1957 2593 1627 1836 2073 1977 2960
TDPLD 1980 2087 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 12000 12000 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0
TRQCST 1998 2105 1170 1839 1839 1216 1470 1701 819 27963
LP24PA 1999 2106 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 1032 1291 1291 519 775 776 1288 785
DETQLM 1704 2111 7735 5220 5140 6224 6450 5682 12830 2300
AMRDML 1705 2112 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0
NINTCT 1735 2127 1688 3041 3041 2041 1871 1853 1000 11851
MFWKCE 1736 2128 2500 6000 2000 2500 4000 4000 1000 4500
MFWKBL 1752 2129 2829 1560 1553 2580 2574 2063 3854 1038
LP2GP 1753 2130 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 5140 2590 3085 5150 5150 5150 7690 2570
PHDLY2 1757 2134 8995 8990 8990 8990 8990 8988 8990 12810
DGCSMM 1782 2159 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 128 128 128 128 128 128 128 140
POVC21 1785 2162 32764 32764 32717 32766 32765 32765 32765 32745
POVC22 1786 2163 48 46 637 28 37 38 44 292
POVCLMT2 1787 2164 8124 8124 10815 5177 6687 6846 7743 13952
MAXCRT 1788 2165 165 165 165 165 165 165 165 365
ACCBSLM 2717 2304 0 0 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0 0 0 22
DCIDBS 2723 2310 0 0 0 0 0 0 0 1112
TITLE
(90B8/M, 90B1/M)
DRAW. No.
1 2009.03.04 B-65270EN/07-014
CUST.
Design.
SHEET
Notice of the Update of Digital Servo Software for Series 30i, 31i, 32i -A (90E0) Ver.3

PARAMETER MANUAL
Spec. No./ Ver. B-65270EN / 07

Correct, Del Date
Basic Function 1. Power Consumption Monitor Function New 2009. 05
2. Changes of Standard Parameter Table Add 2009. 05
Optional
Function
Unit
Maintenance
Parts
Notice
Correction Corrected the mistake of motor model in page 4. Correct 2009.10

(Correct βiS8/6000 to βiS1/6000.)
Another
TITLE
03 09.10.14 Tang Page 4 was changed.
02 09.06.16 Tang Page 4 was changed. Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
01 09.05.11 Tang Newly designed B-65270EN/07-015
SHEET
Notice of the Update of Digital Servo Software for Series 30i, 31i, 32i -A(90E0) Ver.3
1. Update Edition
90E0 27.0 Series30i, 31i, 32i -A (For HRV2 and HRV3 control)
- Power Consumption Monitor Function
The calculation of electric power for Power Consumption Monitor Function has been added.

3. Attached
Attached 1 About Power Consumption Monitor Function
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Attached 1. About Power Consumption Monitor Function
(1) Outline
Power consumption monitor function has been developed. The electric power consumption and
integral power consumption servo motor and spindle motor can be read through the interface of PMC
window, FOCAS2 interface or etc. Custom application can observe consumed power and regenerative
power of servo and spindle axes. Then you can use them to appeal your machine with the energy saving
ability.
For details of Power Consumiption Monitor Function, please refer to A-92345 [FANUC Series 30i /
31i /32i -A Power Consumption Monitor Function Descriptions] to be pubished soon.
Spindle Servo CNC

motor motor
Servo Control
PS SP SV Electric power consumption of
FSSB Servo motor
Loss of Servo Amplifier
Loss of power supply
Spindle control System soft Integral power consumption

Electric Power Consumption of servo axes ( SV)
Integral power consumption of
of Spindle motor
Loss of Spindle amplifier spindle axes( (SP)
Loss of power supply
PMC
Electric power consumption
FOCAS2 Fuction Integral power consumption
Electric power consumption
Integral power consumption
(2) Available System Software ,Servo software and Spindle software

■ Applicable servo software
90E0/27.0 and subsequent editions
■ Applicable System Soft (CNC)
・Series 30i-A： G004, G014, G024, G034/ 4.0 and subsequent editions
・Series 31i-A： G104, G114 / 4.0 and subsequent editions
・Series 31i-A5：G124, G134 / 4.0 and subsequent editions
・Series 32i-A： G204 / 4.0 and subsequent editions
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
(1) Standard parameters of the following servo motors are optimized for the stablity at high speed.

3 βiS1/6000 282
αiS8/6000 290
αiS8/6000HV 292
(2) High speed modles are added in αi series servo motor.
αiS12/6000 462
αiS12/6000HV 463
(3) Parameter about torque constant for Large Servo Motor αiS2000/2000HV and αiS3000/2000HV
has been changed.

For 30i-A series
αiS2000/2000HV 459
4 winding motor
For 30i-A series
αiS3000/2000HV 460
4 winding motor
Currently in the above motors, the 1/10 of torque constant value is set to avoid overflow of N2105. Therefore, 10
times of the torque command should have been given when you use torque control with these motors.
In this edition function bit N2301#7 that makes setting format of N2105 1/10 times smaller has been prepared.
<Notice>
1． To use torque control with this parameter, following system software is needed.
2 ・Series 30i-A： G004, G014, G024/11 and subsequent editions
・Series 31i-A： G104, G114 / 11 and subsequent editions
・Series 31i-A5：G124, G134 / 11 and subsequent editions
・Series 32i-A： G204 / 11 and subsequent edition
2. If the system software does not support it, illegal parameter alarm will happen. Please set N2301#7=0
first, then please give the 10 times torque command as usual.
03 09.10.14 Tang Corrected the mistake of Motor Model. TITLE

Series and edition of system software
02 09.06.16 Tang has been added Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Table1) Standard parameter table for changes and new added models (Checked parameters are changed.) (HRV2,HRV3)
βiS1 αiS8 αiS8 αiS2000 αiS3000 αiS12 αiS12
Motor model
6000 6000 6000HV 2000HV 2000HV 6000 6000HV
Motor ID number 282 290 292 459 460 462 463
Symbol FS30i,31i,32i
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 01000011 01000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00100000 00100000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 10011110 10011010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 10000000 10000000 00000000 00000000
PK1 2040 312 460 381 643 772 471 471
PK2 2041 -1360 -1760 -1749 -3600 -3819 -2249 -2249
PK3 2042 -1203 -1305 -1305 -1358 -1357 -1321 -1321
PK1V 2043 6 53 53 502 652 43 43
PK2V 2044 -53 -478 -478 -4500 -5836 -387 -387
PK3V 2045 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 -7176 -794 -794 843 650 -980 -980
BLCMP 2048 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 3787 3787 1894 1894
PHYST 2055 319 319 319 319 319 319 319
EMFCMP 2056 -12850 0 0 0 0 0 0
PVPA 2057 -15114 -16398 -16398 -3363 -2088 -12808 -12808
PALPH 2058 -1200 -1000 -1000 -3200 -5000 -1800 -1800
PPBAS 2059 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0
POVC1 2062 32695 32520 32548 32309 32309 32688 32688
POVC2 2063 915 3101 2755 5734 5734 998 998
TGALMLV 2064 4 4 4 4 4 4 4
POVCLMT 2065 2714 9224 8192 27346 27346 2960 2960
PK2VAUX 2066 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0
AALPH 2074 20480 8192 8192 12288 12288 12288 12288
OSCTPL 2077 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0
RTCURR 2086 1212 2075 2075 2893 3187 1181 1181
TDPLD 2087 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0
TRQCST 2105 89 346 346 6221 8472 837 837
LP24PA 2106 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0
MGSTCM 2110 1556 1284 1284 784 267 528 528
DETQLM 2111 10290 10255 10255 1510 2218 10260 10260
AMRDML 2112 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0
NINTCT 2127 881 801 1600 3449 3029 1146 2292
MFWKCE 2128 1500 1000 1400 3000 2700 667 667
MFWKBL 2129 5135 5388 5390 1291 777 3850 3850
LP2GP 2130 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0
PHDLY1 2133 15400 10250 10260 2060 2068 7690 7690
PHDLY2 2134 12840 12830 12835 6420 6410 8990 8990
DGCSMM 2159 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 140 140 0 0
POVC21 2162 32767 32765 32765 32745 32745 32764 32764
POVC22 2163 12 38 38 292 292 45 45
POVCLMT2 2164 2340 6857 6857 13952 13952 1721 1721
MAXCRT 2165 25 85 45 365 365 165 85
ACCBSLM 2304 0 0 0 2720 0 0 0
ACDCEND 2305 0 0 0 4114 22 0 0
DCIDBS 2310 0 0 0 1236 1112 0 0
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Notice of contents of Learning Control
Name FANUC AC SERVO MOTOR ai series

FANUC AC SERVO MOTOR bi series
Parameter manual

Correct, Del Date
Basic Function
Optional Addition of explanation about the contents of Learning Add 2010.2

Function Control
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
01 2010.02.15 N. Sonoda Newly designed
SHEET
1. Outline
Learning Control is the control method to minimize the effect of disturbance and following error in
the reiterating command or disturbance. This control enables to automatically minimize control
deviation by repetition of the same movement. The compensation data (Learning data) to minimize
control deviation are generated into the special volatile memory (Learning memory). Furthermore it
is possible to preserve the generated Learning data in CNC’s memory or other external memory
(Learning data transmission function) and also to reuse it. In this case, the learning operation to
minimize control deviation becomes unnecessary and it is possible to realize high precision from the
beginning of the machining.
Learning Control is applied to Cam or Clank-pin grinding machine, gear cutting machine to requite
high speed and high precision. Learning Control limited to the application of Rigid Tap and the mass
production of same shape parts are also prepared. (cf. the following figure)
According to the application, the following options for Learning Control should be selected.
Option “Learning Control” or “Preview Repetitive Control” works under High Speed cycle cutting
(G05) or High-speed binary operation. It needs the servo card which has large memory. It is possible
to save each learning data into plural learning memory corresponding to each works and possible to
transfer each learning data to CNC’s memory or external memory. This function is applied for Cam
or Crank-pin grinding. Option “Preview Repetitive Control” is applied to machining with gradually
changing command such as the one in piston lathe. It enables to suppress the bad effect of
changing command.
Option “Compact Learning Control” works under the reiterating command programmed by the
normal ISO code. It doesn’t adopt the time but adopt the position or angle as the base of learning
cycle. And as it realizes the Learning control with less memory, the standard servo card can be
used for it. But there is a limitation that it is impossible to save the plural learning data and to
transfer learning data to CNC’s memory etc.. This option is applied to oscillation processing in
grinding machine and gear cutting.
Option “Learning Control for Parts cutting” is the special option for parts cutting at manufacturing
plenty of the same parts. Option “Learning Control for Rigid Tap” is the Special option for Rigid Tap.
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
SHEET
Option Application CNC Servo card
Learning Control Cam grinding

Crank-pin grinding Large memory
/ Preview Repetitive 30i /31i
Piston lathe type
Control
Lens cutting
General
Gear cutting
Compact Learning Standard type
Jig grinding 30i /31i
Control Oscillation cutting
Learning Control Parts cutting Large memory

for Parts Cutting type
Limitation 30i /31i /32i
Learning Control Standard type
Rigid Tap
for Rigid Tap
2. Available Servo Software

The following table shows a comparison between servo software for standard and for Learning
Control.
Software series for standard Software series for Learning Control Remark
Servo series name Applied CNC Servo series name Applied CNC
90D0 Series30i-A 90D3 Series30i-A HRV2, HRV3, HRV4
Series31i-A (A02B-0303-H590 Series31i-A
#90D3)
90E0 Series30i-A 90E3 Series30i-A HRV2, HRV3
90E1 Series31i-A (A02B-0303-H590 Series31i-A
Series32i-A #90E3) Series32i-A
Note)
When the following options are used, please pay attention to the edition of servo software.
Compact Learning Control 90E3 series edition 05 or later
Learning Control for Rigid Tap 90D3 series edition 03 or later or
90E3 series edition 01 or later
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
SHEET
3. Number of controlled axis
Maximum number of controlled axes of CNC system depends on the applied servo card and the
kind of HRV control. On the other hand, when Learning Control is used, the number of available
axes might decrease depending on the number of axes for Learning Control (learning axis). The
following table gives the information of available number of controlled axis when Learning
Control is used.
Option 30i /31i (32i)
Learning Control (Max. number of controlled axes)

／Preview Repetitive Control −(Max. number of learning axes)
Compact Learning Control (Max. number of controlled axes)

−(Max. number of learning axes)
Learning Control Max. number of controlled axes
for Parts Cutting （Regardless of number of learning
axes）
Learning Control Max. number of controlled axes
for Rigid Tap （Regardless of number of learning
axes）
Example) Suppose
that option “Learning Control” is used, 90E3 series is used, servo card L24 is used, and HRV3 is used.
If the number of learning axes is 4, the available number of controlled axes becomes 8 because of the
number of max. controlled axes of L24 is 12.
4. Order specification
1) Options and Hardware

Option ＣＮＣ CPU card Servo card
Learning Control
(A02B-xxxx-J705) 30i /31i D3（A02B-0303-H010） Large memory type
Preview Repetitive Control L24 (A02B-0303-H088)
(A02B-xxxx-J706)
Compact Learning Control 30i /31i All types Standard type
(A02B-030x-R692)
Learning Control A6（A02B-0303-H013） Large memory type
for Parts cutting 30i /31i /32i C6（A02B-0308-H016） L24 (A02B-0303-H088)
(A02B-030x-R510) D3（A02B-0303-H010）
Learning Control A6（A02B-0303-H013）

for Rigid Tap 30i /31i /32i C6（A02B-0308-H016） Standard type
(A02B-030x-R539) D3（A02B-0303-H010）
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
SHEET
2) Software options
When either “Learning Control” or “Preview Repetitive Control” is used, one of the following
options is indispensable.
High Speed cycle cutting A02B-030x-J832
High-speed binary operation A02B-030x-R516
When the above options are used, the following related options should be selected as the
occasion demands.
High-speed cycle machining skip function A02B-030x-S662
High-speed cycle machining retract function A02B-030x-J663
High-speed cycle cutting additional variables A / B A02B-030x-J745/J746
High-speed cycle cutting additional variables C / D A02B-030x-S640/R513
High-speed binary operation retract function A02B-030x-S658
Superimposed control for high-speed cycle machining
A02B-030x-R554
Superimposed control A02B-030x-S818
（Indispensable option to use “Superimposed control for high-speed cycle machining”）
High-speed cycle machining operation information output function

A02B-030x-R609
Spindle control switching function for High-speed cycle machining
A02B-030x-R608
In cam and crank-pin grinding using the plural profiles, the following option is necessary.
Learning memory expanded function A02B-030x-J976
Note) This option requires either option “Learning Control” or “Preview Repetitive Control”.
In case of machining by reciprocation to in Jig grinding machine, the following option is necessary.
High precision oscillation function A02B-030x-R662
Note) The above specification “xxxx” is different value corresponding to each CNC.
5. Axis allocation
In case of servo software 90D3, learning axis should be allocated to odd axis 1, 3, 5, 7… in
No.1023. On the other hand, in case of servo software 90E3, learning axis should be allocated to
1, 5, 9, 13… in No.1023.
CNC Servo software series No.1023

90D3 1, 3, 5, 7…
30i /31i /32i
90E3 1, 5, 9, 13…
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
SHEET
6. Related documents
Please refer to the following documents to know the detail of each option because various
parameters setting and operations are necessary to use Learning Control.
Learning Control / Preview Repetitive Control

“FANUC AC Servo software 90D3/90E3 series Learning Function Operator’s Manual” (A-63639-
108)
Compact Learning Control

”FANUC AC Servo software 90E3 series Compact Learning Control Operator’s Manual”(A-63639-
188)
Learning Control for Parts Cutting

”FANUC AC Servo software 90D3/90E3 series Learning Control for Parts Cutting Operator’s
Manual”(A-63639-115)
Learning Control for Rigid Tap

”FANUC AC Servo software 90D3/90E3 series Learning Control for Rigid Tap Operator’s
Manual”(A-63639-131)
Reference)
Spindle Learning Control (Option)
Spindle Learning Control is applied to spindle motor control. Especially this is used with gear
cutting using Electric Gear Box (EGB). If servo option either “Learning Control” or “Preview
Repetitive Control” is available, Spindle Learning Control is available also even without this
option itself.
Spindle Learning Control

“FANUC AC SPINDLE MOTOR αi series Spindle Learning Control Description” (A-63639-132)
TITLE
DRAW. No.
B-65270EN/07-016
CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 0i-D, 0i Mate-D (90C5,90E5)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1 Supporting Trouble Diagnosis Function New 2009. 08
2 Changes of Standard parameter table Add 2009. 08
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
for Series 0i-D, 0i Mate-D (90C5,90E5)
DRAW. No. CUST.
01 09.08 .06 Tang Newly designed B-65270EN/07-017
SHEET
Notice of the Update of Digital Servo Software for Series 0i -D, 0i Mate -D(90C5, 90E5)
1. Update Edition
90C5 04 Series 0i-D, 0i Mate-D
Series 0i-D
90E5 04
(for two-path system of Series 0i-TD)
- Supporting Trouble Diagnosis Function
Trouble Diagnosis Function has been supported.

3. Attached
Attached 1 Supporting Trouble Diagnosis Function
TITLE
Series 0i-D, 0i Mate -D (90C5,90E5)
DRAW. No. CUST.
SHEET
Attached 1. Supporting Trouble Diagnosis Function
(1) Outline
Trouble Diagnosis Function is a function which can forecast trouble, send imformation to PMC,
and diagnose trouble to stop trouble cause at earlier time.
According to the guidance message, servo alarms can be diagnosed easily. And when the thermal
simulation or disturbance level of servo axis exceeds the trouble forecast level, a trouble forecast
signal can be output.
For details of Trouble Diagnosis Function, please refer to A-92727 [FANUC Series 0i-TD/MD
FANUC Series 0i Mate-TD/MD TROUBLE DIAGNOSIS FUNCTION Specifications]

90C5/04 and subsequent editions
90E5/04 and subsequent editions (For two-path system of Series 0i -TD)
(3) Step of diagnosis

Trouble Diagnosis Guidance Screen includes : Trouble Code ,Contents of Trouble, Probable
Cause, Guidance message and Status display.
When alarm happens, please answer the questions in the trouble diagnosis guidance screen by
pushing soft keys [ YES ]/[ NO ]. The probable cause of alarm and the method to remove the
problem will be shown at the end.
Trouble Code
Contents of trouble
Probable cause
Guidance message
Status display
Fig.(a) Trouble diagnosis guidance screen

See the servo/spindle monitor information in the trouble diagnosis monitor screen and
waveform of servo/spindle in the trouble diagnosis graphic screen in case of need according to
the guidance message.
Fig. (b) Trouble diagnosis monitor screen
TITLE
DRAW. No. CUST.
SHEET
(1) Standard parameters for OVC alarm of the following servo motors are the optimized .

αiF 30/3000 303
αiF 40/3000 307
αiF 40/3000Fan 308
αiS 22/4000 315
αiS 30/4000 318
αiS 40/4000 322
Note) Please refer to Table1 about the standrad parameters.
(2 ) Standard parameters of the following servo motors are the optimized for the stablity at high speed.

βiS 1/6000 282
αiS 8/6000 290
αiS 8/6000HV 292
Note) Please refer to Table1 about the standard parameters.
(3) Serval αi series servo motor modles are added

αiS 60/3000Fan 328
αiS 60/3000HVFan 329
αiS 12/6000 462
αiS 12/6000HV 463
αiS 4/6000 466

αiS 4/6000HV 467
αiS 50/2000 468

αiS 50/2000HV 469
αiS 60/2000 470
αiS 60/2000HV 471

Note) Please refer to Table 2 about the standard parameters.
TITLE
DRAW. No. CUST.
SHEET
Table1) Standard parameter table for changes (Checked parameters are changed.)
Motor model βiS1 αiS8 αiS8 αiF30 αiF40 αiF40 αiS22 αiS30 αiS40
6000 6000 6000HV 3000 3000 3000Fan 4000 4000 4000
Motor ID number 282 290 292 303 307 308 315 318 322
Symbol FS0i-D
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00100000 00100000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 312 460 381 768 1500 1500 581 799 712
PK2 2041 -1360 -1760 -1749 -4492 -8224 -8224 -3844 -4447 -4138
PK3 2042 -1203 -1305 -1305 -1347 -1348 -1348 -1337 -1317 -1341
PK1V 2043 6 53 53 230 191 191 69 82 92
PK2V 2044 -53 -478 -478 -2057 -1712 -1712 -616 -733 -827
PK3V 2045 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 -7176 -794 -794 1845 2216 2216 6163 5175 4589
BLCMP 2048 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319
EMFCMP 2056 -12850 0 0 -20500 0 0 0 0 0
PVPA 2057 -15114 -16398 -16398 -8465 -2570 -2570 -7687 -6412 -5645
PALPH 2058 -1200 -1000 -1000 -1657 -2000 -2000 -2000 -2300 -3000
PPBAS 2059 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0
POVC1 2062 32695 32520 32548 32515 32515 32431 32515 32515 32515
POVC2 2063 915 3101 2755 3166 3166 4212 3166 3166 3166
TGALMLV 2064 4 4 4 4 4 4 4 4 4
POVCLMT 2065 2714 9224 8192 9418 9418 12545 9418 9418 9418
PK2VAUX 2066 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0
AALPH 2074 20480 8192 8192 4096 0 0 4096 4096 4096
OSCTPL 2077 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0
RTCURR 2086 1212 2075 2075 2306 1957 2593 1627 1836 2073
TDPLD 2087 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 12000 12000 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0
TRQCST 2105 89 346 346 1170 1839 1839 1216 1470 1701
LP24PA 2106 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1556 1284 1284 1032 1291 1291 519 775 776
DETQLM 2111 10290 10255 10255 7735 5220 5140 6224 6450 5682
AMRDML 2112 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0
NINTCT 2127 881 801 1600 1688 3041 3041 2041 1871 1853
MFWKCE 2128 1500 1000 1400 2500 6000 2000 2500 4000 4000
MFWKBL 2129 5135 5388 5390 2829 1560 1553 2580 2574 2063
LP2GP 2130 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0
PHDLY1 2133 15400 10250 10260 5140 2590 3085 5150 5150 5150
PHDLY2 2134 12840 12830 12835 8995 8990 8990 8990 8990 8988
DGCSMM 2159 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 128 128 128 128 128 128
POVC21 2162 32767 32765 32765 32764 32764 32717 32766 32765 32765
POVC22 2163 12 38 38 48 46 637 28 37 38
POVCLMT2 2164 2340 6857 6857 8124 8124 10815 5177 6687 6846
MAXCRT 2165 25 85 45 165 165 165 165 165 165
ACCBSLM 2304 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0
TITLE
DRAW. No. CUST.
SHEET
Table2) Standard parameter table for new added models
Motor model αiS60 αiS60 αiS12 αiS12 αiS4 αiS4 αiS50 αiS50 αiS60 αiS60
3000Fan 3000HVFan 6000 6000HV 6000 6000HV 2000 2000HV 2000 2000HV
Motor specification 0278 0279 0230 0237 0210 0214 0042 0043 0044 0045
Motor ID number 328 329 462 463 466 467 468 469 470 471
Symbol FS0i-D
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 01000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1191 1131 471 471 395 432 1539 1539 1358 1358
PK2 2041 -6320 -5966 -2249 -2249 -1606 -1673 -7321 -7321 -6767 -6767
PK3 2042 -1347 -1345 -1321 -1321 -1277 -1266 -1344 -1344 -1344 -1344
PK1V 2043 69 69 43 43 76 77 90 90 103 103
PK2V 2044 -617 -617 -387 -387 -678 -688 -802 -802 -925 -925
PK3V 2045 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 6152 6152 -980 -980 5601 5516 4731 4731 4103 4103
BLCMP 2048 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 0 0 0
PPMAX 2053 31979 31979 21 21 21 21 31979 31979 31979 31979
PDDP 2054 3 3 1894 1894 1894 1894 3 3 3 3
PHYST 2055 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0
PVPA 2057 -4619 -4620 -12808 -12808 -13326 -13326 -3867 -3867 -3097 -3097
PALPH 2058 -2000 -2000 -1800 -1800 -2500 -2500 -3393 -3393 -2995 -2995
PPBAS 2059 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32388 32388 32688 32688 32310 32288 32515 32501 32515 32501
POVC2 2063 4744 4745 998 998 5728 5995 3166 3332 3166 3332
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 14138 14140 2960 2960 17091 17893 9418 9912 9418 9912
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0
AALPH 2074 8192 4096 12288 12288 16384 16384 8192 8192 0 0
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 1937 1937 1181 1181 2585 2586 1856 1856 2018 2018
TDPLD 2087 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 4411 4411 837 837 104 104 2569 2569 2942 2942
LP24PA 2106 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 519 519 528 528 3092 3092 1032 1032 1544 1544
DETQLM 2111 5220 5220 10260 10260 8208 8208 4954 4954 3151 3151
AMRDML 2112 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 2852 5393 1146 2292 660 1368 2825 5651 5498 5498
MFWKCE 2128 5000 3000 667 667 3000 3000 4601 4601 4004 4004
MFWKBL 2129 1300 1300 3850 3850 4365 4365 1296 1296 1302 1302
LP2GP 2130 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 5150 5150 7690 7690 7690 7690 2570 2570 4146 4146
PHDLY2 2134 8990 8990 8990 8990 12830 12830 12814 12814 12821 12821
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 128 0 128 0
POVC21 2162 32742 32742 32764 32764 32763 32763 32764 32764 32761 32764
POVC22 2163 327 327 45 45 58 63 51 48 81 51
POVCLMT2 2164 5973 5974 1721 1721 9912 10651 6831 6829 8124 7077
MAXCRT 2165 365 185 165 85 25 10 165 85 165 85
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0
TITLE
DRAW. No. CUST.
SHEET
Specification of expansion tandem function for 30i series CNC

Parameter manual

Correct, Del Date
Basic Function
Optional In Feed axis synchronization control or Tandem Add immediately

Function control, Expansion Tandem control enables to drive
the plural number motors or the large motor with plural
windings.
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Specification of expansion tandem function
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
01 2009.11.02 K. Maeda Newly designed
SHEET
(1) Summary
In a method to control one axis with two motors, there are Torque Tandem
control and Synchronous control (Position Tandem control). Synchronous
control gives the same position command to two axes of a master and a slave,
and it is a method to control a position. A position of a master and a slave is
controlled separately. On the other hand in Tandem control, Position is
controlled by main axis only. In sub axis, only torque is controlled.
In case to control one axis with more than 2 motors, you put Synchronous
control and Torque Tandem control together such as a following example.
Furthermore we recommend you to use Expanded Tandem function together
for stability.
Synchronous Synchronous Synchronous Synchronous

Master Slave-1 Slave-2 Slave-3
Gears Gears Gears Gears

Box Box Box Box
Fig 1 (a) Example for 4 axes control (4 axes Synchronous control)
Synchro. Master Synchro. Slave

Tandem Main Pinion Tandem Main
Gear Gear
Box Box
Tandem Tandem
Gear Gear
Box Box
Tandem Sub Tandem Sub

Synchronous control
Synchro. Slave Synchro. Slave

Tandem Main Tandem Main
Gear Gear
Box Box
Tandem Tandem
Gear Gear
Box Box
Tandem Sub Tandem Sub
Rack
Fig 1 (b) Example for 8 NC axes using (4 pair Tandem control, 4 axes Synchronous control)
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
The situation is similar in Large servo motors (2 windings type : αiS300/2000,
αiS500/2000, and αiS1000/2000HV) or Large servo motors (4 windings type :
αiS2000/2000HV, and αiS3000/2000HV).

Pinion
Gear Gear
Box Box
Large servo motor Large servo motor
(2 amp. type) (2 amp. type)
Synchronous control
Synchro. Slave Synchro. Slave
Gear Gear
Box Box
Rack
Fig 1 (c) Example for 8 NC axes using (4 pair of two windings motors, 8 axes Synchronous control )

Pinion
Gear Gear
Box Box
Synchronous control
Rack
Fig 1 (d) Example for 8 NC axes using (2 pair of four windings motors, 8 axes Synchronous control)
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
Expanded Tandem function can support the followings.
Integrator copy function from 1 to 8 axes in servo software 90E0 series
In case of followings, you should use “Integrator copy function for 4 axes”.
When you drive two motors with Synchronous control, there is a possibility
that interference occurs by slight difference of stop position between axes in
case of mechanically high rigidity, and torque offset occurs. (There is a
possibility that OVC alarm occurs at the worst case.) In such a situation,
interference between axes is suppressed by copying integrator of master
velocity loop to integrator of slave velocity loop.
As a similar problem might occur in case of driving an axis with synchronized 4
motors or 2 pair tandem motors, we developed the function to copy integrator of
main axis to integrator one axis in 4 axes. This function is available to
maximum 8 axes between synchronous axes.
Form : Copying integrator of master axis to integrators of tree other axes in
four synchronous axes. Fig.1(a)
Form : A Form that there are four pairs of tandem control axes, and to copy
integrator between main axes of tandem. Fig.1(b)
Form : A Form that there are four large servo motors (with two windings)
that are occupied by two axes, and to copy integrator between the
master axis and the slave axes. The above four large servo motors are
controlled by Feed Axis Synchronization control function. Fig.1(c)
Form : A Form that there are two large servo motors (with four windings)
that are occupied by four axes, and to copy integrator between the
master axis and the slave axis. The above two large servo motors are
controlled by Feed Axis Synchronization control function. Fig.1(d)
It is similar in the case of four linear motors instead of large servo
motors with four windings .
(2) Applicable servo software series and editions

Series 90E0/U(21) and subsequent editions
(3) Parameters setting method

(Note) In this manual, servo axis is called by the following name respectively
according to the setting value of No.1023.
No.1023 = 4n+1 L axis
= 4n+2 M axis
= 4n+3 J axis
= 4n+4 K axis
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
Setting for Integrator copy function for 4 axes
#7 #6 #5 #4 #3 #2 #1 #0
- SLTMAS SLTAN
2223(FS30i)
SLTAN (#5) 1: Enables Expanded Tandem control. Power must be off

(Set to all axes of master and slave)
Series 90E0/J(10)
∗ In case of changing this parameter, you must turn CNC power off.
∗ By setting this parameter to 1, you can use “Integrator copy function” and
“The servo alarm of plural axes simultaneous monitor function” for more than
3 axes. L axis is the master of Integral copy function. In case that you use
conventional “Integrator copy function” for 2 axes (L and M axes, or K and J
axes), this bit must be set to 0.
In following case, you must set “1” to SLTAN for all synchronous axes.
• Integrator copy function for more than 3 axes in 90E0
SLTMAS (#6) 0: Slave axis

Power must be off
1: Master axis
Series 90E0/J(10)
∗ You must set 1 to master axis. It is possible to set SLTMAS=1 only in L axis
of each DSP. If you set SLTMAS=1 to an axis except L axis, the illegal
parameter alarm will occur.
#7 #6 #5 #4 #3 #2 #1 #0
- WSVCP
2273(FS30i)
WSCCP (#1) 1: Enables copying integrator of master to integrator of slave

(You set 1 to axes which need sharing integrator.) Power must be off
Series 90E0/J(10)
∗ By using this function together with SLTAN, “Integrator copy function” is
available for more than 3 axes
∗ You should set 1 to axes which need sharing integrator. (It doesn’t include the
sub axis of Torque tandem.)
∗In case of SLTAN = 0, Integrator copy function is available for two axes
(between L and M axes or between J and K axes).
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
#7 #6 #5 #4 #3 #2 #1 #0
- PLW4
2211(FS30i)
PLW4(#7) 1: Enables large servo motor with 4 windings. Power must be off
(Set to all four axes.)
Series 90E0/U(21)
∗ By setting this parameter to 1, you can use “Integrator copy function” and
“Position feedback copy function" for four axes.
∗ In case of using this parameter, you need Tandem control option.
Setting for “Velocity Command (Vcmd) Tandem control"
#7 #6 #5 #4 #3 #2 #1 #0
- VCMDTM
2008 (FS30i)
VCMDTM (#5) 1: Enables Velocity Command (Vcmd) Tandem control.

(Set to master axis under Tandem control)
* Please use this function in the axes using Tandem control
* We recommend Feed axis synchronous control rather than this function.
Setting for “Servo alarm of plural axes simultaneous monitor function” for 4 axes
#7 #6 #5 #4 #3 #2 #1 #0
- ESP2AX
2007(FS30i)
ESP2AX (#0) 1: Enables Servo alarm of plural axes simultaneous monitor function.
Series 90E0/J(10)
∗ In case of SLTAN = 0, “Integrator copy function” is available for 2 axes.
(Conventional spec.)
∗ By using this function together with SLTAN, “Servo alarm of plural axes
simultaneous monitor function” for more than 3 axes becomes effective.
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
Setting for “Preload function in case of above 2 axes”
#7 #6 #5 #4 #3 #2 #1 #0
- TIMCAL TIMPR2
2417 (FS30i)
TIMCAL (#4) Preload time constant is : 90E0/25(Y)

0 : Not available. Time constant is 0. (Conventional spec.)
1 : Available.
∗ When you use this function, a mechanical shock at the start of excitation will
be reduced because motor outputs preload torque with time constant.
∗ As for time constant, please refer to the below bit (TIMPR2).
TIMPR2 (#2) Exponential time constant for preload is : 90E0/25(Y)

0 : Reciprocal of position loop gain (1/s).
1 : 4 times of reciprocal of position loop gain (1/s).
- Preload value (PRLOAD)

2087 (FS30i)
To add each reverse torque offset to master and slave axes enables to reduce a backlash among
tandem axes. In case that you set preload value to more than 2 axes, please set it so that the
summation of preload value is 0.
(Example)
Synchronous Synchronous Synchronous Synchronous
Master Slave-1 Slave-2 Slave-3
Gears Gears Gears Gears

Box Box Box Box
Axis allocation Expansion Expansion Integrator Preload Remarks

number No.1023 Tandem Tandem Master copy No.2087
2223#5 No.2223#6 No.2273#1
1 1 (L) 1 1 1 +600 Synchronous Master
2 2 (M) 1 0 1 -300 Synchronous Slave
3 3 (J) 1 0 1 +300 Synchronous Slave
4 4 (K) 1 0 1 -600 Synchronous Slave
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
(4) Examples of parameters setting
(4-1) In case of driving 4 axes by synchronous control, and using Integrator copy function for 4 axes. (Form )
Position DSP1
Command Velocity L axis Master axis
CNC Control
Feedback
M1
Velocity
M axis Slave axis
Control Feedback
M2
Feed Axis Integrator
Synchronization copy
Control
J axis
Velocity Slave axis
Control Feedback
M3
K axis
Velocity Slave axis
Control Feedback
Integrator M4
copy
Axis Tandem Expanded Exp. Tandem Integrator

Axis
Allocation control Tandem Master copy Remarks
Number
No.1023 No.1817#6 No.2223#5 No.2223#6 No.2273#1
1 1 (L) 0 1 1 1 Master of Synchronous control
2 2 (M) 0 1 0 1 Slave for 1st. axis
3 3 (J) 0 1 0 1 Slave for 1st. axis
4 4 (K) 0 1 0 1 Slave for 1st. axis
*1) Set Feed Axis synchronous control to four axes (from 1st. axis to 4th. axis).
(4-2) In case of driving 2 axes (M1 and M2) by synchronous control, and those axes are controlled by Torque Tandem
control, and those axes use Integrator copy function. (Form )
Position
Command DSP1 Velocity L axis Master axis
CNC Control
Feedback
Tandem
M1
control
Velocity M axis Sub axis
Control (Vcmd Tandem)
Feed Axis
Synchronization M3
Control Integrator
copy
Velocity J axis Slave axis

Control
Feedback
Tandem
M2
control
Velocity K axis Sub axis
Control (Vcmd Tandem)
Integrator M4
copy
Axis Tandem Vcmd Expanded Exp. Tandem Integrator

Axis
Allocation control Tandem Tandem Master copy Remarks
Number
No.1023 No.1817#6 No.2008#5 No.2223#5 No.2223#6 No.2273#1
Master of Synchronous control
1 1 (L) 1 1 1 1 1
(1st. tandem main)
Slave for 1st. axis
2 3 (J) 1 1 1 0 1
(2nd. tandem main)
3 2 (M) 1 0 1 0 1 1st. tandem sub
4 4 (K) 1 0 1 0 1 2nd. tandem sub
*1) Pair of 1st. axis and 3rd. axis, and pair of 2nd. axis and 4th. axis are Tandem control (Vcmd Tandem).
*2) Set Feed Axis synchronous control to 1st. axis and 2nd. axis.
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
(4-3) In case of driving 4 axes by synchronous control, and using Integrator copy function for 4 axes with 2 windings
motor. (Form )
Position
Command DSP1 Velocity 1-L axis
CNC Master axis
Control
Feedback
M1
1-M axis Sub axis
Integrator
Feed Axis copy Torque (Torque Copy)
Synchronization Command
Control
Velocity 1-J axis Slave axis
Control
Feedback
M2
1-K axis Sub axis
Integrator
(Torque Copy)
copy
DSP2
Velocity 2-L axis Slave axis
Control
Feedback
M3
2-M axis Sub axis
Integrator
copy Torque (Torque Copy)
Command
Velocity 2-J axis Slave axis
Control
Feedback
M4
2-K axis Sub axis
(Torque Copy)
Axis Tandem Position FB Expanded Exp. Tandem Integrator

Axis
Allocation control copy Tandem Master copy Remarks
Number
No.1023 No.1817#6 No.2018#7 No.2223#5 No.2223#6 No.2273#1
Master of Synchronous
1 1 (1-L) 1 0 1 1 1 control
(1st. tandem main)
Slave for 1st. axis
2 3 (1-J) 1 0 1 0 1
(2nd. tandem main)
Slave for 1st. axis
3 5 (2-L) 1 0 1 0 1
(3rd. tandem main)
Slave for 1st. axis
4 7 (2-J) 1 0 1 0 1
(4th. tandem main)
5 2 (1-M) 1 1 1 0 0 1st. tandem sub
6 4 (1-K) 1 1 1 0 0 2nd. tandem sub
7 6 (2-M) 1 1 1 0 0 3rd. tandem sub
8 8 (2-K) 1 1 1 0 0 4th. tandem sub
*1) Set Feed Axis synchronous control to 1st. axis, 2nd., 3rd. and 4th. axis.
*2) Integrator of 1st. axis will be copied to 2nd. axis, 3rd. axis and 4th. axis
*3) Pair of 1st. axis and 5th. axis, pair of 2nd. and 6th. axis, pair of 3rd. and 7th. axis and pair of 2nd. axis and 6th.
axis are Tandem control.
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
(4-4) In case of driving 2 axes by synchronous control, and using Integrator copy function for 2 axes with 4 windings
motor. (Form )
Position
Command DSP1 Velocity 1-L axis
CNC Master axis
Control
Feedback
M1
1-M axis Sub axis
(Torque Copy)
Torque
Feed Axis Command
Synchronization 1-J axis Sub axis
Control
(Torque Copy)
1-K axis Sub axis

Integrator
copy (Torque Copy)
DSP2
Velocity 2-L axis Slave axis
Control
Feedback
M2
2-M axis Sub axis
(Torque Copy)
Torque
Command
2-J axis Sub axis
(Torque Copy)
2-K axis Sub axis

(Torque Copy)
Axis Ext axis Tandem 4 Amp. drive Expanded Exp. Tandem Integrator
Axis
Allocation name *4 control motor Tandem Master copy Remarks
Num.
No.1023 No.1025 No.1817#6 No.2211#7 No.2223#5 No.2223#6 No.2273#1
Master of
1 1 (1-L) 49 (_1) 0 1 1 1 1
Synchronous control
Slave of Synchronous
2 5 (2-L) 50 (_2) 0 1 1 0 1
control
3 2 (1-M) 51 (_3) 0 1 1 0 0 Sub for 1st. axis
4 3 (1-J) 52 (_4) 0 1 1 0 0 Sub for 1st. axis
5 4 (1-K) 53 (_5) 0 1 1 0 0 Sub for 1st. axis
6 6 (2-M) 54 (_6) 0 1 1 0 0 Sub for 2nd. axis
7 7 (2-J) 55 (_7) 0 1 1 0 0 Sub for 2nd. axis
8 8 (2-K) 56 (_8) 0 1 1 0 0 Sub for 2nd. axis
*1) Set Feed axis synchronous control to 1st. axis and 2nd. axis.
*2) Integrator of 1st. axis will be copied to 2nd. axis.
*3) By using 4 windings motor function, feedback data and torque data will be copied from 1st. axis to 3rd, 4th, and
5th. axis and from 2nd. axis to 6th, 7th, and 8th. axis.
Each sub axis doesn’t need Position feedback copy function (No.2018#7).
*4) In this case, you must set the other program axis name, which is different from 1st and 2nd axis, to the axes from
3rd to 8th . If not, real speed will smaller than your command speed.
You should set the other value to No.1025 with No.1000#0 = 1.
TITLE
for 30i series CNC
DRAW. No.
B-65270EN/07-018
CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 31i (90D0)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Changes of Standard Parameter Table Add 2009. 10
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i / 31i (90D0)
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i /31i (90D0)
1. Update Edition
90D0 22 Series30i / 31i (For HRV4 control)
3. Attached
TITLE
Series 30i / 31i (90D0)
DRAW. No. CUST.
SHEET
(1) Soft thermal(OVC) alarm level for the following servo motors are optimized.
αiF 30/3000 303

αiF 40/3000 307
αiF 40/3000Fan 308
αiS 22/4000 315
αiS 30/4000 318
αiS 40/4000 322
αiS 22/6000 452
(2 ) Standard parameters of the following servo motors are optimized for the stablity at high speed.
βiS 1/6000 282

αiS 8/6000 290
αiS 8/6000HV 292
(3) High speed modles are added in αi series servo motor.

αiS 12/6000 462

αiS 12/6000HV 463
TITLE
Series 30i / 31i (90D0)
DRAW. No. CUST.
SHEET
αiF30 αiF40 αiF40 αiS22 αiS30 αiS40 αiS22
Motor model
3000 3000 3000Fan 4000 4000 4000 6000
Motor ID number 303 307 308 315 318 322 452
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00100000 00100000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 768 1500 1500 581 799 712 605
PK2 2041 -4492 -8224 -8224 -3844 -4447 -4138 -2393
PK3 2042 -1347 -1348 -1348 -1337 -1317 -1341 -1335
PK1V 2043 230 191 191 69 82 92 102
PK2V 2044 -2057 -1712 -1712 -616 -733 -827 -914
PK3V 2045 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 1845 2216 2216 6163 5175 4589 4150
BLCMP 2048 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319
EMFCMP 2056 -20500 0 0 0 0 0 0
PVPA 2057 -8465 -2570 -2570 -7687 -6412 -5645 -12039
PALPH 2058 -1657 -2000 -2000 -2000 -2300 -3000 -2000
PPBAS 2059 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0
POVC1 2062 32515 32515 32431 32515 32515 32515 32515
POVC2 2063 3166 3166 4212 3166 3166 3166 3166
TGALMLV 2064 4 4 4 4 4 4 4
POVCLMT 2065 9418 9418 12545 9418 9418 9418 9418
PK2VAUX 2066 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0
AALPH 2074 4096 0 0 4096 4096 4096 4096
OSCTPL 2077 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0
RTCURR 2086 2306 1957 2593 1627 1836 2073 1977
TDPLD 2087 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0
DBLIM 2102 0 12000 12000 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0
TRQCST 2105 1170 1839 1839 1216 1470 1701 819
LP24PA 2106 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0
MGSTCM 2110 1032 1291 1291 519 775 776 1288
DETQLM 2111 7735 5220 5140 6224 6450 5682 12830
AMRDML 2112 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0
NINTCT 2127 1688 3041 3041 2041 1871 1853 1000
MFWKCE 2128 2500 6000 2000 2500 4000 4000 1000
MFWKBL 2129 2829 1560 1553 2580 2574 2063 3854
LP2GP 2130 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0
PHDLY1 2133 5140 2590 3085 5150 5150 5150 7690
PHDLY2 2134 8995 8990 8990 8990 8990 8988 8990
DGCSMM 2159 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0
OVCSTP 2161 128 128 128 128 128 128 128
POVC21 2162 32764 32764 32717 32766 32765 32765 32765
POVC22 2163 48 46 637 28 37 38 44
POVCLMT2 2164 8124 8124 10815 5177 6687 6846 7743
MAXCRT 2165 165 165 165 165 165 165 165
ACCBSLM 2304 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0
TITLE
Series 30i / 31i (90D0)
DRAW. No. CUST.
SHEET
Table2) Standard parameter table for changes and new added models (Checked parameters are changed.)
βiS1 αiS8 αiS8 αiS12 αiS12
Motor model
6000 6000 6000HV 6000 6000HV
Motor ID number 282 290 292 462 463
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 312 460 381 471 471
PK2 2041 -1360 -1760 -1749 -2249 -2249
PK3 2042 -1203 -1305 -1305 -1321 -1321
PK1V 2043 6 53 53 43 43
PK2V 2044 -53 -478 -478 -387 -387
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 -7176 -794 -794 -980 -980
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 0 0 0 0 0
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 -12850 0 0 0 0
PVPA 2057 -15114 -16398 -16398 -12808 -12808
PALPH 2058 -1200 -1000 -1000 -1800 -1800
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32695 32520 32548 32688 32688
POVC2 2063 915 3101 2755 998 998
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 2714 9224 8192 2960 2960
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 20480 8192 8192 12288 12288
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 1212 2075 2075 1181 1181
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 89 346 346 837 837
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 1556 1284 1284 528 528
DETQLM 2111 10290 10255 10255 10260 10260
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 881 801 1600 1146 2292
MFWKCE 2128 1500 1000 1400 667 667
MFWKBL 2129 5135 5388 5390 3850 3850
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 15400 10250 10260 7690 7690
PHDLY2 2134 12840 12830 12835 8990 8990
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 32767 32765 32765 32764 32764
POVC22 2163 12 38 38 45 45
POVCLMT2 2164 2340 6857 6857 1721 1721
MAXCRT 2165 25 85 45 165 85
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0
TITLE
Series 30i / 31i (90D0)
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 15i/ 16i/ 18i/ 21i/ PMi-D/ PMi-H (90BP)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. New Position Detection Circuits for Linear Motor have New 2009.11
been supported.
2. Changes of Standard Parameter Table Add 2009.11
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
DRAW. No. CUST.
SHEET
1. Update Edition
FS15i, 16i, 18i, 21i, PMi -D, PMi-H
90BP 06
- New Position Detection Circuits for Linear Motor
New Position Detection Circuits for Linear Motor have been supported.
3. Attached
- Attached 1 Changes of Standard Parameter Table
- Attached 2 New Position Detection Circuits for Linear Motor
TITLE
Series 15i / 16i / 18i / 21i / PMi –D / PMi -H ( 90BP)
DRAW. No. CUST.
SHEET
Attached 1. New Position Detection Circuits for Linear Motor
(1) Outline
The position detection circuits for linear motor (A860-2033-T201, A860-2033-T202, A860-2033-T301, A860-2033-T302)
have been supported for digital servo soft 90BP series.

90BP/06(F) and subsequent editions
(3)Configuration
Position detection circuits A860-2033-Txxx for linear motor have been supported. And overheat alarm of linear motor can
be detected by using the position detection circuit.
Servo amplifier
CNC
Power lead
Thermostat signal
( overheat detection signal)
Position information
Separate position
detector
Linear motor position
detection circuit
(4) Parameter setting

Please set the following parameter depending on the connection type (configuration) of overheat alarm. (Please refer
PARAMETER MANUAL B-65270JA/07 4.14.2 for details)
Note) When following parameters are changed, it is necessary to turn OFF/ON CNC.
#7 #6 #5 #4 #3 #2 #1 #0
No.2713(FS15i) CKLNOH THRMO
No.2300(FS16i)
THRMO(#3) In case that No.2300#7 is set to “1”, motor overheat alarm is
0: detected from DI signal via PMC.
1: detected from linear motor position detection circuit
CLKNOH(#7) Overheat alarm for linear motor is

1: detected from DI signal via PMC, or linear motor position detection circuit
CKLNOH THRMO meaning
1 0 Detecting overheat alarm by DI signal via PMC.

Detecting overheat alarm by thermostat signal connected to linear
1 1
motor position detection circuit.
Note) Temperature detection circuit has not been supported by 90BP series.
TITLE
DRAW. No. CUST.
SHEET

βiS 1/6000 282
αiS 8/6000 290
αiS 8/6000HV 292
αiF 22/3000 297
Note) To support the changes of αiF22/3000, following Servo Ampilfier and Power Supply Module are needed
Servo Amplifier Power Supply Module
200V Driver 200V Driver:A06B-6140-Hxxx
(1) A06B-6114-Hxxx 400V Driver:A06B-6150-Hxxx
(S/N:V078xxxxx or subsequent editions)
(2) A06B-6117-Hxxx
400V Driver
(1) A06B-6124-Hxxx
(S/N:V078xxxxx or subsequent editions)
(2) A06B-6127-Hxxx
(2) 3000/min model of αis series Large Servo motors have been added.
αiS 300/3000HV 344
αiS 500/3000HV 347
αiS 1000/3000HV 350
with PDM
(3) Following models are added in αis series.

Motor Model Motor ID No. Refer
αiS 12/6000 462

αiS 12/6000HV 463 High speed model
αiS 4/6000 466 for Live Tool
αiS 4/6000HV 467

αiS 50/2000 468
αiS 50/2000HV 469 High cost-performance model
αiS 60/2000 470 driven by 160A and 80A(HV)amplifier
αiS 60/2000HV 471

αiS 60/3000Fan 328 High power model
αiS 60/3000HVFan 329 driven by 360A and 180A(HV) amplifier
TITLE
DRAW. No. CUST.
SHEET
αiS1000
βiS1 αiS8 αiS8 αiF22 αiS300 αiS500
Motor model 3000HV
6000 6000 6000HV 3000 3000HV 3000HV
With PDM
Motor ID number 282 290 292 297 344 347 350
Symbol FS15i FS16i,18i,PMi
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00100000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000001
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00000000 00011010 00011010 00011010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 10000000
PK1 1852 2040 312 460 381 1750 821 1344 960
PK2 1853 2041 -1360 -1760 -1749 -6000 -5450 -7296 -6554
PK3 1854 2042 -1203 -1305 -1305 -1345 -1355 -1357 -1362
PK1V 1855 2043 6 53 53 198 91 111 191
PK2V 1856 2044 -53 -478 -478 -1775 -819 -996 -1708
PK3V 1857 2045 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -7176 -794 -794 2137 4633 3811 2221
BLCMP 1860 2048 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0
PPMAX 1865 2053 21 21 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319 319 319
EMFCMP 1868 2056 -12850 0 0 0 0 0 0
PVPA 1869 2057 -15114 -16398 -16398 -5136 -5646 -3856 -4620
PALPH 1870 2058 -1200 -1000 -1000 -2800 -1800 -2900 -2500
PPBAS 1871 2059 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0
POVC1 1877 2062 32695 32520 32548 32520 32380 32380 32488
POVC2 1878 2063 915 3101 2755 3101 4850 4850 3503
TGALMLV 1892 2064 4 4 4 4 4 4 4
POVCLMT 1893 2065 2714 9224 8192 9224 12155 12155 18280
PK2VAUX 1894 2066 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0
SERIESLPH 1961 2068 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0
AALPH 1967 2074 20480 8192 8192 12288 12288 12288 12288
OSCTPL 1970 2077 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0
RTCURR 1979 2086 1212 2075 2075 2131 2000 2482 2599
TDPLD 1980 2087 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 15000 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0
TRQCST 1998 2105 89 346 346 929 13494 18125 3807
LP24PA 1999 2106 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0
MGSTCM 1703 2110 1556 1284 1284 1291 523 521 1040
DETQLM 1704 2111 10290 10255 10255 0 2960 2953 3242
AMRDML 1705 2112 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0
NINTCT 1735 2127 881 801 1600 3272 7720 8021 9876
MFWKCE 1736 2128 1500 1000 1400 4500 4300 2500 4500
MFWKBL 1752 2129 5135 5388 5390 1301 1556 1041 1556
LP2GP 1753 2130 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0
PHDLY1 1756 2133 15400 10250 10260 0 3100 3093 2580
PHDLY2 1757 2134 12840 12830 12835 0 6422 6418 6418
DGCSMM 1782 2159 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 140 140 140
POVC21 1785 2162 32767 32765 32765 32765 32700 32700 32721
POVC22 1786 2163 12 38 38 40 853 853 589
POVCLMT2 1787 2164 2340 6857 6857 7229 10644 10644 13952
MAXCRT 1788 2165 25 85 45 85 0 0 0
ACCBSLM 2717 2304 0 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 29 32 29
DCIDBS 2723 2310 0 0 0 1817 1700 1400 1648
TQLMSV 2715 2302 0 0 0 0 20 20 0
TQLMST 2729 2316 0 0 0 0 5394 5394 0
TITLE
DRAW. No. CUST.
SHEET
αiS60 αiS60 αiS12 αiS12 αiS4 αiS4 αiS50 αiS50 αiS60 αiS60
Motor model
3000Fan 3000HVFan 6000 6000HV 6000 6000HV 2000 2000HV 2000 2000HV
Motor ID number 328 329 462 463 466 467 468 469 470 471
symbol FS15i FS16i,18i,PMi
1808 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 01000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1954 2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1707 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1708 2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1750 2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1751 2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2713 2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 1191 1131 471 471 395 432 1539 1539 1358 1358
PK2 1853 2041 -6320 -5966 -2249 -2249 -1606 -1673 -7321 -7321 -6767 -6767
PK3 1854 2042 -1347 -1345 -1321 -1321 -1277 -1266 -1344 -1344 -1344 -1344
PK1V 1855 2043 69 69 43 43 76 77 90 90 103 103
PK2V 1856 2044 -617 -617 -387 -387 -678 -688 -802 -802 -925 -925
PK3V 1857 2045 0 0 0 0 0 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 6152 6152 -980 -980 5601 5516 4731 4731 4103 4103
BLCMP 1860 2048 0 0 0 0 0 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510 510 510 510 510 510
RESERV 1864 2052 0 0 0 0 0 0 0 0 0 0
PPMAX 1865 2053 31979 31979 21 21 21 21 31979 31979 31979 31979
PDDP 1866 2054 3 3 1894 1894 1894 1894 3 3 3 3
PHYST 1867 2055 319 319 319 319 319 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0 0 0 0 0 0
PVPA 1869 2057 -4619 -4620 -12808 -12808 -13326 -13326 -3867 -3867 -3097 -3097
PALPH 1870 2058 -2000 -2000 -1800 -1800 -2500 -2500 -3393 -3393 -2995 -2995
PPBAS 1871 2059 0 0 0 0 0 0 0 0 0 0
TQLIM 1872 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 1873 2061 0 0 0 0 0 0 0 0 0 0
POVC1 1877 2062 32388 32388 32688 32688 32310 32288 32515 32501 32515 32501
POVC2 1878 2063 4744 4745 998 998 5728 5995 3166 3332 3166 3332
TGALMLV 1892 2064 4 4 4 4 4 4 4 4 4 4
POVCLMT 1893 2065 14138 14140 2960 2960 17091 17893 9418 9912 9418 9912
PK2VAUX 1894 2066 0 0 0 0 0 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0 0 0 0 0 0
SERIESLPH 1961 2068 0 0 0 0 0 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0 0 0 0 0 0
AALPH 1967 2074 8192 4096 12288 12288 16384 16384 8192 8192 0 0
OSCTPL 1970 2077 0 0 0 0 0 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0 0 0 0 0 0
RTCURR 1979 2086 1937 1937 1181 1181 2585 2586 1856 1856 2018 2018
TDPLD 1980 2087 0 0 0 0 0 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0 0 0 0 0 0
TRQCST 1998 2105 4411 4411 837 837 104 104 2569 2569 2942 2942
LP24PA 1999 2106 0 0 0 0 0 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0 0 0 0 0 0
MGSTCM 1703 2110 519 519 528 528 3092 3092 1032 1032 1544 1544
DETQLM 1704 2111 5220 5220 10260 10260 8208 8208 4954 4954 3151 3151
AMRDML 1705 2112 0 0 0 0 0 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0 0 0 0 0 0
NINTCT 1735 2127 2852 5393 1146 2292 660 1368 2825 5651 5498 5498
MFWKCE 1736 2128 5000 3000 667 667 3000 3000 4601 4601 4004 4004
MFWKBL 1752 2129 1300 1300 3850 3850 4365 4365 1296 1296 1302 1302
LP2GP 1753 2130 0 0 0 0 0 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0 0 0 0 0 0
PHDLY1 1756 2133 5150 5150 7690 7690 7690 7690 2570 2570 4146 4146
PHDLY2 1757 2134 8990 8990 8990 8990 12830 12830 12814 12814 12821 12821
DGCSMM 1782 2159 0 0 0 0 0 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0 0 128 0 128 0
POVC21 1785 2162 32742 32742 32764 32764 32763 32763 32764 32764 32761 32764
POVC22 1786 2163 327 327 45 45 58 63 51 48 81 51
POVCLMT2 1787 2164 5973 5974 1721 1721 9912 10651 6831 6829 8124 7077
MAXCRT 1788 2165 365 185 165 85 25 10 165 85 165 85
ACCBSLM 2717 2304 0 0 0 0 0 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0 0 0 0 0 0
DCIDBS 2723 2310 0 0 0 0 0 0 0 0 0 0
TQLMSV 2715 2302 0 0 0 0 0 0 0 0 0 0
TQLMST 2729 2316 0 0 0 0 0 0 0 0 0 0
TITLE
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/31i/32i-A(90E1 & 90E3)

Parameter manual

Correct, Del Date
Basic Function ・ Inertia Estimation function New 2009.11
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
Notice of the Update of Digital Servo Software for Series 30i/31i/32i -A (90E1 & 90E3)
1. Update Edition

90E1 03.0 FS30i /31i /32i-A (For HRV2 and HRV3 control)
90E3 05.0 FS30i /31i /32i -A

(For HRV2 and HRV3 control & Learning Control)
Note: 90E1 series is upper compatible with 90E0 series. 90E1 series supports revisions
up to edition 27.0 in 90E0 series. 90E3 series is servo software for Learning Control.
Inertia Estimation function
This function estimates the inertia of the machine.

Please refer to the attached document for the details.
3. Attached
Attached document 1: Inertia Estimation function
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
Attached document 1: Inertia Estimation function
(1) Outline
This function estimates the inertia of machine without backlash like the rotary
table by Direct Drive. Generally since the various works are loaded on the rotary
table, the inertia of the table changes depending on these works. Therefore it is
possible to optimize “Velocity Gain” and “Time Constant of Acc./Dec.” depending
on the various inertias by estimating the inertia.
(2) Available Servo Software

(Series 30i, 31i, 32i-A )
90E1 series version C(03) or later
90E3 series version E(05) or later
(3) Notice
This function is unavailable if the target axis is fixed by clamper or something.
The accuracy of inertia estimation will be worse in machine with the large
backlash or the large torsion.
Disturbance elimination filter is unavailable during the estimation.
Since the estimation accuracy depends on the machine condition, you should
sufficiently confirm it before you apply this function in the field.
(4) Parameters
#7 #6 #5 #4 #3 #2 #1 #0
--- INESGH INESGL INESFH INESFL INESMG INESFC
2419 (FS30i)
INESFC (#2) Inertia Estimation function is
0: Ineffective.
1: Effective.
INESMG (#3) Output unit for Diagnosis screen No.764 is

0: Standard.
1: 1/32 times of standard.
If error “-3” appears on Diagnosis screen No.764 after the estimation, it means the
overflow of the result. In such case, please set this bit and estimate again.
INESFL (#4) Input frequency for Inertia Estimation is

0: Standard.
1: Low frequency.
INESFH (#5) Input frequency for Inertia Estimation is

0: Standard.
1: High frequency.
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
INESGL (#6) Input gain for Inertia Estimation is
0: Standard.
1: Half of standard.
If Excess Error at stop (SV410) occurs during the estimation, you should expand
the range for Excess Error at stop (No.1829) or make this bit effective, and estimate
again.
input gain is too much. In such case also, please make this bit effective and
estimate again. If it isn’t still improved, you should change “Input frequency” to
“High” (No.2419#5=1).
INESGH (#7) Input gain for Inertia Estimation is

0: Standard.
1: Twice of standard.
input gain is too small. Please make this bit effective and estimate again. If it isn’t
still improved, you should change “Input frequency” to “Low” (No.2419#4=1).
No.2419 INESGH #7 INESGL #6 INESFH #5 INESFL #4

Input frequency “Standard” －－ 0 0
“Low” －－ 0 1
“High” －－ 1 0
－－－ 1 1
Input gain “Standard” 0 0 －－
“Half” 0 1 －－
“Twice” 1 0 －－
－ 1 1 －－
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
#7 #6 #5 #4 #3 #2 #1 #0
IQOB
2200 (FS30i)
IQOB (#2) Influence of control voltage saturation is
0: Neglected.
1: Eliminated. (Please set this.)
2086 (FS30i) Rated current

“Input gain” for Inertia Estimation is calculated by this parameter
and No.2419#7, #6.
2345 (FS30i) Friction compensation

[Data unit] TCMD unit (Max. current of amplifier is 7282.)
[Data range] 0 to 7282
[Initial setting] 0
This parameter means the compensation to eliminate the effect of friction torque.
You set the absolute value of torque command (TCMD) during the movement at
10min-1 (Rotary motor) or 10mm/sec (Linear motor) to this parameter.
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
(5) PMC Signals
PMC signal G390 controls “Start” and “Stop” for inertia estimation. Motor oscillates
in a narrow range for 2 sec after the estimation start. PMC signal F371 informs
“Finish” after the estimation. At the same time, the estimation result is shown on
Diagnosis screen No.764. The estimation result of Diagnosis screen No.764 is kept
until next estimation. This result is available with PMC program.
In case of plural winding motor, Tandem Control and Feed axis synchronization
control, PMC signal G390 should be input to both master-axis and slave-axis at the
same time. The sum of the estimation result in each axis shows the total inertia.
----------------------------------------------------------------------------------------------------------
Inertia estimation start DI signal
G390
[Function] Control “Start “/ “Stop” for Inertia Estimation
[Operation] The estimation is started by this signal. If this signal becomes
OFF, the estimation is stopped.
----------------------------------------------------------------------------------------------------------
Inertia estimation finish DO signal
F371
[Function] Inform “Finish” for inertia estimation
[Operation] If inertia estimation finishes, this signal becomes ON.
Timing chart
Estimation start ON
G390
Oscillate in a narrow
Estimating
range for 2 sec.
Estimation finish ON
F371
Show the result

Diagnosis screen
No.764 Zero
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
(6) Diagnosis screen
The estimation result is shown on Diagnosis screen No.764. It is possible to
calculate the inertia from this result by using the following formula.
Rotary motor
DGN764× Kt× Imax× P
Jm =
6.4557×10 12
Inertia Jm [kgm2], Torque constant Kt [Nm/Ap], Amplifier max. current Imax [Ap],
Resolution for internal encoder P [pulse]
20 20
Pulse coder αi P=2 , αiCZ sensor 1024S P=2 ,
23
Heidenhain RCN223 and RCN727 encoder P=2
Ex.) αiS8/4000 Kt=0.512 [Nm/Ap], Imax=80 [Ap], P=220 [pulse], Result

DGN764=176, Inertia is Jm=0.00117 [kgm2].
Linear motor
DGN764× Kt× Imax
M =
8.2196×106 × A
Driven weight M [kg], Thrust constant Kt [N/Ap], Amplifier max. current Imax [Ap],
Resolution for sensor A [µm]
0.1µm Linear absolute sensor A=0.1, Linear incremental sensor X[µm]＋High
resolution detection circuit A=X/512 Note) 2048 type is the same setting as 512
type.
Ex.) LiS600A1/4 Kt=25 [N/Ap], Imax=40 [Ap], A=20 [µm]/512,

Result DGN764=1358, Driven weight is M=4.2 [kg].
The estimated inertia is required to be satisfied the following formula.
Rotary motor
Jm×6.4557×1012
2 ≤
5
≤ 220
Kt× Imax× P
Linear motor
M × 8.2196×106 × A
2 ≤
5
≤ 220
Kt× Imax
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
Error display and the countermeasure
The estimation will be immediately suspended when the motor moves with large
acceleration, and error “-1” appears on Diagnosis screen No.764. In this case, you
should set “Input gain” to “Half” (No.2419#6=1) and estimate again. If it isn’t
improved, you have to set “Input frequency” to “High” (No.2419#5=1).
If it is difficult to estimate the correct inertia due to small acceleration, error “-2” will
appear on Diagnosis screen No.764. In this case, you should set “Input gain” to
“Twice” (No.2419#7=1) and estimate again. If it isn’t improved, you have to set
“Input frequency” to “Low” (No.2419#4=1).
If the calculation becomes overflow, error “-3” will appear on Diagnosis screen
No.764. In this case, you should set “Output magnification” to “1/32 time”
(No.2419#3=1) and estimate again.
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
(7) How to Use
The following is an explanation for the preparation and the method to apply inertia
estimation function.
1) Making PMC ladder program

You make the PMC ladder program for the control of inertia estimation referring
to above (5). In case of “Plural winding motor”, “Tandem control” and “Feed axis
synchronization control”, DI signal G390 for inertia estimation start should be
input to both master-axis and slave-axis at the same time.
2) Measurement of friction
You measure the friction. This result is set to No.2345 with the absolute value of
torque command (TCMD) during the movement at 10min-1 (Rotary motor) or
10mm/sec (Linear motor). If you use SERVO GUIDE, and set that “Kind” is
“TCMD”, “Conv. Coef.” and “Conv. Base” are “1”, you can directly read the value
on “Graph Window” for No.2345. If the friction is small, it isn’t necessary to set
this parameter.
3) Confirmation of estimation result

You should try inertia estimation with both minimum work and maximum work
which real inertia is already known. And you confirm that the estimation result
matches with real inertia. If error number (-1,-2,-3) appears on Diagnosis screen
No.764 after the estimation, refer to above (6) “Error display and the
countermeasure”.
4) How to change “Velocity Gain” and “Time Constant of Acc./Dec.”

You suitably tune “Velocity Gain” and “Time Constant of Acc./Dec.” with the work
which real inertia is already known. Next you execute inertia estimation and
memorize the estimation result on Diagnosis screen No.764 as initial value. If
the inertia is changed, you execute again and compare the result and initial
value. Please try to change “Velocity Gain” and “Time Constant of Acc./Dec.”
according to the rate. However, “Velocity Gain” is not always the direct
proportion to the changing rate of inertia. Therefore you should investigate it
beforehand.
TITLE

for Series 30i /31i /32i (90E1 & 90E3)
DRAW. No. CUST.

B-65270EN/07-021
SHEET
Detection of EXCESS ERROR from Estimated Position to Actual Position

PARAMETER MANUAL

Correct, Del Date
Basic Function - Detection of EXCESS ERROR from Estimated Position to New 2009.12
Actual Position
Detection of EXCESS ERROR that is estimating the
machine position during movement and is observing
the error from estimated position to actual position.
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Detection of EXCESS ERROR from Estimated
Position to Actual Position
DRAW. No. CUST.
SHEET
Detection of EXCESS ERROR from Estimated Position to Actual Position
(1) Overview
EXCESS ERROR is detected by observing a position deviation between the actual position and the estimated position. The
estimated position is estimated by using position commands, position gain and feed forward setting. This function has an
effect that the alarm level of EXCESS ERROR automatically becomes lower when the feed rate becomes slow. This
function can shorten the time of detecting EXCESS ERROR when a trouble happens.
(Construction) (Effect)
Standard EXCESS ERROR EXCESS ERROR(SV)
Estimating Speed(Rapid) Speed(Rapid) Alarm Level
position 0.4 x Emax
Emax Error Error
Estimated (Rapid) (Rapid)
Position - Speed(Cut)
Excess Alarm Level
1.2 x Emax
Error Error
Position Actual
(Cut)
Command Position Position
Control Alarm level is decided depending
- Alarm level changes depending
on the maximum error at rapid on the position command. Alarm
traverse.
detection becomes faster when
The decided constant level is the feed rate is low.
applied to whole feed rate.
(2) Series and editions of applicable system software and servo software
System software and servo software are needed to support the detection of EXCESS ERROR from estimated position to
actual position.
System Software
FS30i -A G004, G014, G024, G034 / 2.0 and subsequent editions
FS31i -A5 G124，G134 / 2.0 and subsequent editions
FS31i -A G104, G114 / 2.0 and subsequent editions
FS32i -A G204 / 2.0 and subsequent editions
Servo software
90E0 series / 28.0 and subsequent editions

#7 #6 #5 #4 #3 #2 #1 #0
2419 (FS30i) DYNTQL DYNERR
DYNERR(#0) Detection of Excessive error (SV) alarm is
0: Disable
1: Enable
If DYNERR=1 is used with a CNC that does not support the function, an
illegal parameter setting alarm (detail number 4190) is issued.
DYNTQL(#1) Detection of Excessive error alarm during the torque limit is
0: Enable
1: Disable
2458 (FS30i) EXCESS ERROR detection level

[Valid data range] from 0 to 32767
[Typical setting] 0.2 times of position error in rapid traverse
Rapid traverse feed rate[mm / min]
Setting value = × 0.2
60 × PG[1 / S ] × Detection unit[mm]
(4) Caution and note

When alarm occurs, SV653 EXCESS ERROR (SV) is expressed.
This function does not support Dual Position Feedback Function.
TITLE
DRAW. No. CUST.
SHEET
(5) Detection and tuning example for excessive error alarm (SV)
In general, excessive error alarm level is set to 1.2 times of rapid traverse position error. But the excessive error which is
detetcted by servo software is nearly to 0. In order to get the same detact level, it needs to set the detection alarm level 0.2
times of estimated position error in rapid traverse.
Rapid traverse feed rate[ mm / min]
Setting value = × 0 .2
60 × PG[1 / S ] × Detection unit [ mm ]
If smaller value is needed, please observe the postion error from estimed position to actual position. Then set the detection
level from the observed value to the above setting value. Please note it becomes easier to detect this alarm even in normal
movement if the setting value is too small.
1. Set the parameter to enable excessive error detection

Set the function bit N2419#0=1 and the alarm level N2458=30000. (First set this level large enough to avoid
the alarm)
2. Observe the difference from estimated position to actual position
Using SERVO GUIDE, set values as follows.
SERVE GUIDE channel setting:
Axis: the axis to set EXCESS ERROR
Type: ERR
Unit / Conversion: detection unit
Conversion reference: 1
Origin value: 0.
Extended address: the value corresponding to the servo axis number
according to the table below.
Table Extended address setting.
90E0 series No.1023 Extended address
4n+1 13069
4n+2 13197
4n+3 19213
4n+4 19341
Through the above setting, the excess error can be observed in acceleration and deceleration. Following figure
is an example. You can see the difference from estimated position to actual position is 13µm.
Speed
Difference from estimated position
to actual position
10µm
3. Set alarm level

Since the observed value is 13µm, the value of alarm level should be set from 13µm to 0.2 times of rapid
tranverse position error.
TITLE
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i (90E0)

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Detection of EXCESS ERROR from Estimated New 2009.12
Position to Actual Position New 2009.12
2. Inertia Estimation Function Add 2009.12
3. Changes of Standard Parameter Table
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E0 28.0
(For HRV2 and HRV3 control)
- Detection of EXCESS ERROR from Estimated Position to Actual Postion

Detection of EXCESS ERROR from estimated position to actual postion has been
developed.
Please refer to the Technical report B-65270EN/07-022 [Detection of EXCESS ERROR
from Estimated Position to Actual Postion] for the details.
- Inertia Estimation Function

This function estimates the inertia of the machine.
Please refer to the Technical report B-65270EN/07-021 [Notice of the Update of
Digital Servo Software for Series 30i/ 31i/ 32i (90E1 & 90E3)] for the details.

3. Attached
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Power Supply
Motor Model Motor ID No. Servo Amplifier
Module
200V Driver 200V Driver
αiF 22/3000 297
A06B-6140-Hxxx
A06B-6117-Hxxx
αiS 1000/2000 HV 458
(A06B-0098-Bxxx)
αiS 2000/2000 HV 459 A06B-6127-Hxxx A06B-6150-Hxxx
αiS 3000/2000 HV 460
Power Supply
Module
αiS 300/3000HV 344

400VDriver 400VDriver
αiS 500/3000HV 347 A06B-6127-Hxxx A06B-6150-Hxxx
αiS 1000/3000HV 465
αiS 4/6000 466 High speed model

αiS 4/6000HV 467 for Live Tool
αiS 50/2000 468

driven by
αiS 60/2000 470 160A and 80A(HV)amplifier
αiS 60/2000HV 471
αiS 60/3000 with Fan 328 High power model
driven by 360A and 180A(HV)
αiS 60/3000HV with Fan 329 amplifier
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Motor model
αiF22 αiS60 αiS60 αiS300 αiS500
3000 3000Fan 3000HVFan 3000HV 3000HV
Motor ID number 297 328 329 344 347
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 01000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00001000 00001000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00100000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00000000 00001010 00001010 00011010 00011010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 1750 1191 1131 821 1344
PK2 2041 -6000 -6320 -5966 -5450 -7296
PK3 2042 -1345 -1347 -1345 -1355 -1357
PK1V 2043 198 69 69 91 111
PK2V 2044 -1775 -617 -617 -819 -996
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 2137 6152 6152 4633 3811
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 0 0 0 4200 4200
PPMAX 2053 21 31979 31979 21 21
PDDP 2054 1894 3 3 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0
PVPA 2057 -5136 -4619 -4620 -5646 -3856
PALPH 2058 -2800 -2000 -2000 -1800 -2900
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32520 32388 32388 32380 32380
POVC2 2063 3101 4744 4745 4850 4850
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 9224 14138 14140 12155 12155
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 12288 8192 4096 12288 12288
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 2131 1937 1937 2000 2482
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 15000 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 929 4411 4411 13494 18125
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 1291 519 519 523 521
DETQLM 2111 0 5220 5220 2960 2953
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 3272 2852 5393 7720 8021
MFWKCE 2128 4500 5000 3000 4300 2500
MFWKBL 2129 1301 1300 1300 1556 1041
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 5150 5150 3100 3093
PHDLY2 2134 0 8990 8990 6422 6418
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 140 140
POVC21 2162 32765 32742 32742 32700 32700
POVC22 2163 40 327 327 853 853
POVCLMT2 2164 7229 5973 5974 10644 10644
MAXCRT 2165 85 365 185 0 0
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 29 32
DCIDBS 2310 1817 0 0 1700 1400
TQLMSV 2302 0 0 0 20 20
TQLMST 2316 0 0 0 5394 5394
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Motor model
2000HV 2000HV 2000HV 3000HV 6000 6000HV 2000 2000HV 2000 2000HV
Motor ID number 458 459 460 465 466 467 468 469 470 471
symbol FS30i,31i,32i
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 01000011 01000011 01000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00001000 00000000 00000000 00001000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00011010 10011110 10011010 10011010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 11000000 11000000 10000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1260 643 772 960 395 432 1539 1539 1358 1358
PK2 2041 -8010 -3600 -3819 -6554 -1606 -1673 -7321 -7321 -6767 -6767
PK3 2042 -1362 -1358 -1357 -1362 -1277 -1266 -1344 -1344 -1344 -1344
PK1V 2043 263 502 652 191 76 77 90 90 103 103
PK2V 2044 -2357 -4500 -5836 -1708 -678 -688 -802 -802 -925 -925
PK3V 2045 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 1610 843 650 2221 5601 5516 4731 4731 4103 4103
BLCMP 2048 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510
RESERV 2052 3500 0 0 4200 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 31979 31979 31979 31979
PDDP 2054 3787 3787 3787 1894 1894 1894 3 3 3 3
PHYST 2055 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0
PVPA 2057 -2320 -3363 -2088 -4620 -13326 -13326 -3867 -3867 -3097 -3097
PALPH 2058 -2500 -3200 -5000 -2500 -2500 -2500 -3393 -3393 -2995 -2995
PPBAS 2059 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32309 32309 32309 32488 32310 32288 32515 32501 32515 32501
POVC2 2063 5734 5734 5734 3503 5728 5995 3166 3332 3166 3332
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 27346 27346 27346 18280 17091 17893 9418 9912 9418 9912
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0
AALPH 2074 12288 12288 12288 12288 16384 16384 8192 8192 0 0
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 2960 2893 3187 2599 2585 2586 1856 1856 2018 2018
TDPLD 2087 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 2800 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 27963 5957 8472 3807 104 104 2569 2569 2942 2942
LP24PA 2106 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 785 784 267 1040 3092 3092 1032 1032 1544 1544
DETQLM 2111 2300 2022 2218 3242 8208 8208 4954 4954 3151 3151
AMRDML 2112 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 11851 3449 3029 9876 660 1368 2825 5651 5498 5498
MFWKCE 2128 4500 3000 2700 4500 3000 3000 4601 4601 4004 4004
MFWKBL 2129 1038 1291 777 1556 4365 4365 1296 1296 1302 1302
LP2GP 2130 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 2570 2060 2068 2580 7690 7690 2570 2570 4146 4146
PHDLY2 2134 12810 12820 6410 6418 12830 12830 12814 12814 12821 12821
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 140 140 140 140 0 0 128 0 128 0
POVC21 2162 32745 32745 32745 32721 32763 32763 32764 32764 32761 32764
POVC22 2163 292 292 292 589 58 63 51 48 81 51
POVCLMT2 2164 13952 13952 13952 13952 9912 10651 6831 6829 8124 7077
MAXCRT 2165 365 365 365 365 25 10 165 85 165 85
ACCBSLM 2304 0 2720 0 0 0 0 0 0 0 0
ACDCEND 2305 22 4112 22 29 0 0 0 0 0 0
DCIDBS 2310 1112 1236 1112 1648 0 0 0 0 0 0
TQLMSV 2302 0 0 0 0 0 0 0 0 0 0
TQLMST 2316 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Revision of operation manual for Inertia Estimation function
Name FANUC AC SERVO MOTOR @+ series

FANUC AC SERVO MOTOR #+ series
FANUC LINEAR MOTOR L+S series
FANUC SYNCHRONOUS BUILT-IN SERVO MOTOR D+S series
Parameter manual

Correct, Del Date
Basic Function Operation manual for Inertia Estimation
function Add 2011.04
/ Addition of velocity oscillation method
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Operation manual for Inertia Estimation
function
02 2011.04.01 N.sonoda Updated to edition 02
DRAW. No. CUST.
01 2010.01.20 N. Sonoda Newly designed Y.Toyozawa B-65270EN/07-024
SHEET
Operation manual for Inertia Estimation function
(1) Outline
This function estimates inertia of machine. In linear axis or rotary axis to drive
works, the inertia is changed by the loaded various works. In this case if the
inertia can be estimated, it is possible to optimize “Velocity Gain” and “Time
Constant of Acc./Dec.” depending on the various inertias. The estimation is
started by PMC signal and the result is shown on diagnosis screen No.764. This
function has the following two methods.
“Oscillation by torque method” … Available to direct drive using linear motor or
DD motor.
“Oscillation by velocity method” … Available to ball-screw drive using rotary type
motor with shaft.
(2) Available Servo Software

(Series 30i-A, 31i-A, 32i-A)
90E0 series version 28.0 or later
90E1, 90E4 series version 03.0 or later
The following is version to support the improvement of detective sensitivity
(No.2418#2) and “Tandem control”.
The following is version to support “Velocity oscillation method” (No.2418#3).
(Series 0i-D)
90C8, 90E8 series version 01.0 or later
90C5, 90E5 series version 05.0 or later
(Series 30i-B, 31i-B, 31i-B5, 32i-B)
90G0 series version 09.0 or later
90G3 series version 02.0 or later
(Note) This function requires the following CNC software.

FS30i-A : G002, G012, G022, G032 edition 30.0 or later
: G003, G013, G023, G033 edition 13.0 or later
FS31i-A5 : G121, G131 edition 30.0 or later
: G123, G133 edition 13.0 or later
FS31i-A : G101, G111 edition 30.0 or later
: G103, G113 edition 13.0 or later
FS32i-A : G201 edition 30.0 or later
: G203 edition 13.0 or later
FS0i-MD : D4F1 edition 01.0 or later
FS0i-TD : D6F1 edition 01.0 or later
FS0i Mate-MD : D5F1 edition 01.0 or later
FS0i Mate-TD : D7F1 edition 01.0 or later
FS30i-B : G301, G311, G321 edition 02.0 or later
FS31i-B : G401, G411 edition 02.0 or later
FS31i-B5 : G421, G431 edition 02.0 or later
FS32i-B : G501 edition 02.0 or later
TITLE
function
02 2011.04.01 N.sonoda Addition
DRAW. No. CUST.
01 2010.01.20 N. Sonoda Newly designed B-65270EN/07-024
SHEET
(3) Notice
This function estimates inertia by adding small oscillation to motor. Therefore
this function is not available if the target axis is fixed by clamper or something.
The accuracy of inertia estimation will be worse in machine with the large
backlash or the large torsion, and in machine of low stiffness applied “Tandem
control” or “Feed axis synchronization control”.
“Disturbance elimination filter” is unavailable during the estimation.
Since the estimation accuracy depends on the machine condition, you should
sufficiently confirm it before you apply this function in the field.
(4) Parameters
#7 #6 #5 #4 #3 #2 #1 #0
--- INESGH INESGL INESFH INESFL INESMG INESFC
2419 (FS30i,0i-D)
INESFC (#2) Inertia Estimation function is
0: Ineffective
1: Effective
INESMG (#3) Output unit for Diagnosis screen No.764 is

0: Standard
1: 1/32 times of standard
overflow of the result. In such case, please set this bit and estimate again.
INESFL (#4) Oscillation frequency for Inertia Estimation is

0: Standard (50Hz)
1: Low frequency (25Hz)
INESFH (#5) Oscillation frequency for Inertia Estimation is

0: Standard (50Hz)
1: High frequency (100Hz)
INESGL (#6) Oscillation gain for Inertia Estimation is

0: Standard (Rated current)
1: Half of standard (Rated current /2 )
If Excess Error at stop (SV410) occurs during the estimation, you should expand
the range for Excess Error at stop (No.1829) or make this bit effective, and estimate
again.
input gain is too much. In such case also, please make this bit effective and
estimate again. If it isn’t still improved, you should change “Oscillation frequency” to
“Low” (No.2419#4=1).
INESGH (#7) Oscillation gain for Inertia Estimation is

0: Standard (Rated current)
1: Twice of standard (Rated current x2 )
TITLE
function
DRAW. No. CUST.

SHEET
input gain is too small. Please make this bit effective and estimate again. If it isn’t
still improved, you should change “Oscillation frequency” to “High” (No.2419#5=1),
or you should change “Detectable minimum acceleration “ to “1/32”
(No.2418#2=1).
#7 #6 #5 #4 #3 #2 #1 #0
--- INEVCM INESHS
2418 (FS30i,0i-D)
INESHS (#2) Detectable minimum acceleration for Inertia Estimation is set to
0: normal
1: 1/32 (Improvement of detective sensitivity)
If error “-2” appears on Diagnosis screen No.764 after the estimation, please
change this bit to 1/32 and estimate again.
INEVCM (#3) Inertia estimation uses

0: Oscillation by torque method
1: Oscillation by velocity method
Oscillation by torque method is applied to direct drive using linear motor or DD
motor. On the other hand, Oscillation by velocity method is applied to ball-screw
drive using rotary type motor with shaft.
Above two bit parameters require appropriate servo software. Please refer to the
said (2) “Available Servo Software”.
Setting for measure to detective error (Oscillation by torque method)

Parameter No.2419 No2418
Bit INESGH #7 INESGL #6 INESFH #5 INESFL #4 INESHS #2
Oscillation frequency “Standard” －－ 0 0 －
“Low” in case of Error-1 －－ 0 1 －
“High” in case of Error-2 －－ 1 0 －
Oscillation gain “Standard” 0 0 －－－

“Half” in case of Error-1 0 1 －－－
“Twice” in case of Error-2 1 0 －－－
Detectable min. accel. －－－－ 1
“1/32” in case of Error-2
Oscillation frequency
2025 (FS30i,0i-D)
[Data unit] 1Hz
[Standard] 5
This parameter means the oscillation frequency for Inertia Estimation. This
parameter is irrelevant to parameter No.2419#4, #5. This parameter requires
appropriate servo software. Please refer to the said (2) “Available Servo Software”.
TITLE
function
DRAW. No. CUST.
SHEET
Oscillation gain
2026 (FS30i,0i-D)
[Data unit] 0.1min-1
[Standard] 5000
This parameter means the oscillation gain for Inertia Estimation. This parameter is
irrelevant to parameter No.2419#6, #7. This parameter requires appropriate servo
software. Please refer to the said (2) “Available Servo Software”.
Setting for measure to detective error (Oscillation by velocity method)

Parameter No.2025 No.2026 No2418
Bit INESHS #2
Oscillation frequency “Standard” 5 －－
“Low” in case of Error-1 3 －－
“High” in case of Error-2 10 －－
Oscillation gain “Standard” － 5000 －

“Half” in case of Error-1 － 2500 －
“Twic” in case of Error-2 － 10000 －
Detectable min. accel. －－ 1
“1/32” in case of Error-2
#7 #6 #5 #4 #3 #2 #1 #0
IQOB
2200 (FS30i,0i-D)
IQOB (#2) Influence of control voltage saturation is
0: Not eliminated.
1: Eliminated. (Please set this.)
Rated current
2086 (FS30i,0i-D)
[Data unit] Max. current of amplifier is 6554
In case of Torque oscillation method, “Oscillation gain” for Inertia Estimation is
calculated by this parameter and No.2419#7, #6. This value depends on motor
specification. If No.2086=0, error “-2” will appear.
Friction compensation
2345 (FS30i,0i-D)
[Data unit] TCMD unit (Max. current of amplifier is 7282.)
This parameter means the compensation to eliminate the effect of friction torque.
You set the absolute value of torque command (TCMD) during the movement at
10min-1 (Rotary motor) or 10mm/sec (Linear motor) to this parameter.
TITLE
function
DRAW. No. CUST.
SHEET
If an average current in estimation is less than this parameter, error “-2” appears on
Diagnosis screen No.764. In this case, you should increase oscillation gain.
Note
In “Plural windings motor”, “Tandem control” and “Feed axis synchronization
control”, above all parameters for sub-axis should be set to the same value as
main-axis.
TITLE
function
DRAW. No. CUST.
SHEET
(5) PMC Signals
PMC signal G390 controls “Start” and “Stop” for inertia estimation. Motor oscillates
in a narrow range for 2 sec after the estimation start. PMC signal F371 informs
“Finish” after the estimation. At the same time, the estimation result is shown on
Diagnosis screen No.764. The estimation result of Diagnosis screen No.764 is kept
until next estimation. This result is available with PMC program. In case of “Plural
windings motor” or “Tandem control”, DI signal G390 for inertia estimation start
should input to main-axis only. The estimation result is shown on Diagnosis screen
No.764 of main-axis. On the other hand, in case of “Feed axis synchronization
control”, PMC signal G390 should input to both main-axis and sub-axis at the same
time. The sum of the estimation result in each axis shows the total inertia.
----------------------------------------------------------------------------------------------------------
Inertia estimation start DI signal
G390.0 – G390.7 (axis type)
[Function] Control “Start “/ “Stop” for Inertia Estimation
[Operation] The estimation is started by this signal. If this signal becomes
OFF, the estimation is stopped.
----------------------------------------------------------------------------------------------------------
Inertia estimation finish DO signal
F371.0 – F371.7 (axis type)
[Function] Inform “Finish” for inertia estimation
[Operation] If inertia estimation finishes, this signal becomes ON.
Estimation start ON
G390
Oscillate in a narrow
Estimating
range for 2 sec.
Estimation finish ON
F371
Show the result

Diagnosis screen
No.764 Zero
TITLE
function
02 2011.04.01 N.sonoda Correction
DRAW. No. CUST.
SHEET
(6) Diagnosis screen
The estimation result is shown on Diagnosis screen No.764. It is possible to
calculate the inertia from this result by using the following formula.
Rotary motor
DGN 764 × (Kt/ 2 ) × Im ax × P

Jm =
6.4557 × 1012
2
Inertia Jm [kgm ], Torque constant Kt [Nm/Arms], Amplifier max. current Imax [Ap],
Note) Concerning the motor constant such as Inertia Jm or Torque constant Kt,
please refer to the manual for motor.
Resolution for internal encoder P [pulse]

αiCZ 512A P=2
19
αiCZ 768A P=786432

αi pulse coder, αiCZ 1024A, P=220
RCN220 (Refer to the following example)
RCN223, RCN723, RCN727 P=223
Binary encoder or Non-binary encoder P=(Number of sine waves per
+High resolution serial output circuit detector revolution λ)×256
Note) Variable P is set to resolution for internal encoder not only in semi-closed
system but also in full-closed system.
Ex.) αiS8/4000 Kt=0.72 [Nm/Arms], Imax=80 [Ap], P=2

20
[pulse], Result
2
DGN764=176, Inertia is Jm=0.00116 [kgm ].
Linear motor
DGN 764 × ( Kf / 2 ) × Im ax
M=
8.2196 × 10 6 × A
Driven weight M [kg], Force constant Kf [N/Arms], Amplifier max. current Imax [Ap],
Resolution for sensor A [μm]
Linear incremental sensor A=Signal pitch [μm]/512
+High resolution serial output circuit (Refer to the following example)
Linear absolute sensor A=Resolution [μm]
Ex.) LiS600A1/4 Kf=41.1 [N/Arms], Imax=40 [Ap], A=20 [μm]/512,

Result DGN764=1358, Driven weight is M=4.9 [kg].
TITLE
function
DRAW. No. CUST.

SHEET
The estimated inertia is required to be satisfied the following formula.
Rotary motor
Jm × 6.4557 × 1012
25 ≤ ≤ 2 20
( Kt / 2 ) × Im ax × P
In case of Stall current = Is [Arms]

0.81× Kt × Is × P 0.81× Kt × Is × P×22
≤ Jm ≤
π × 106 × 214 π 2 × 108
In case of applying the improvement of detective sensitivity
(No.2418#2).
Kt × Is × P Kt × Is × P × 2 7
≤ Jm ≤
π × 10 × 2
2 6 13
π2 × 10 7
Linear motor
M × 8.2196 × 10 6 × A
25 ≤ ≤ 2 20
( Kf / 2 ) × Im ax
In case of Continuous force = Ic [Arms]

0.81 × Kf × Ic 0.81 × Kf × Ic
≤M ≤
A× 2 14
25π × A
In case of applying the improvement of detective sensitivity
(No.2418#2).
Kf × Ic Kf × Ic × 27
≤M ≤
π× A × 213
π× A × 10
Note) Concerning Stall current Is or Continuous force Ic, please refer to

the manual for motor.
Error display and the countermeasure
If some errors appear on Diagnosis screen No.764, you should confirm the above
numerical formula for inertia. If this formula is satisfied, refer to the following
countermeasures.
The estimation will be immediately suspended when the motor moves with large
acceleration, and error “-1” appears on Diagnosis screen No.764. In this case, you
should set “Oscillation gain” to “Half” (No.2419#6=1 or No.2026= setting value/2)
and estimate again. If it isn’t improved, you should set “Oscillation frequency” to
“Low” (No.2419#4=1 or No.2025=setting value/2).
If it is difficult to estimate the correct inertia due to small acceleration, error “-2” will
TITLE
function
DRAW. No. CUST.
SHEET
appear on Diagnosis screen No.764. In this case, you should set “Oscillation gain”
to “Twice” (No.2419#7=1 or No.2026=setting value x2) and estimate again. If it isn't
improved, you should set "Oscillation frequency" to "High" (No.2419#5=1 or
No.2025=setting value x2), or you should change “Detectable minimum
acceleration “ to “1/32” (No.2418#2=1).
If the calculation becomes overflow, error “-3” will appear on Diagnosis screen
No.764. In this case, you should set “Output magnification” to “1/32 time”
(No.2419#3=1) and estimate again.
(7) How to Use

The following is an explanation for the preparation and the method to apply inertia
estimation function.
1) Making PMC ladder program

You make the PMC ladder program for the control of inertia estimation referring
to above (5). In case of “Plural windings motor” or “Tandem control”, DI signal
G390 for inertia estimation start should input to main-axis only. On the other
hand, in case of “Feed axis synchronization control”, DI signal G390 should input
to both main-axis and sub-axis at the same time.
2) Measurement of friction
You measure the friction. This result is set to No.2345 with the absolute value of
torque command (TCMD) during the movement at 10min-1 (Rotary motor) or
10mm/sec (Linear motor). If you use SERVO GUIDE, and set that “Kind” is
“TCMD”, “Conv. Coef.” and “Conv. Base” are “1”, you can directly read the value
on “Graph Window” for No.2345. If the friction is small, it isn’t necessary to set
this parameter.
3) Confirmation of estimation result

You should try inertia estimation with both minimum work and maximum work
which real inertia is already known. And you confirm that the estimation result
matches with real inertia. If error number (-1,-2,-3) appears on Diagnosis screen
No.764 after the estimation, refer to above (6) “Error display and the
countermeasure”.
4) How to change “Velocity Gain” and “Time Constant of Acc./Dec.”

You suitably tune “Velocity Gain” and “Time Constant of Acc./Dec.” with the work
which real inertia is already known. Next you execute inertia estimation and
memorize the estimation result on Diagnosis screen No.764 as initial value. If
the inertia is changed, you execute again and compare the result and initial
value. Please try to change “Velocity Gain” and “Time Constant of Acc./Dec.”
according to the rate. However, “Velocity Gain” is not always the direct
proportion to the changing rate of inertia. Therefore you should investigate it
beforehand.
TITLE
function
DRAW. No. CUST.
SHEET

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Supporting Electric Power Consumption Monitor for New 2010.03
βiSV amplifier
2. Improving Inertia Estimation Function Add 2010.03
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E1 04.0
- Supporting Electric Power Consumption Monitor for βiSV amplifier

Electric Power Consumption Monitor for βiSV amplifier has been supported.
- Improveing Inertia Estimation Function

Inertia Estimation function has been improved so that even large inertia is correctly
detected by increasing the detective sensitivity. Besides “Tandem Control” has been also
available.
For the detailed information, please refer to Technical Report TMS10/007

(B-65270EN/07-024) [Operation manual for Inertia Estimation function].

3. Attached
- Attached 1 Supporting Electric Power Consumption Monitor for βiSV amplifier
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
Supporting Electric Power Consumption Monitor for βiSV amplifier
(1) Overview
Electric Power Consumption Monitor for βiSV amplifier has been supported.
(2) Series and editions of servo software

90E1 series /04.0 and subsequent editions

Please set following paramete when using Electric Power Consumption Monitor for βiSV amplifier
(New) #7 #6 #5 #4 #3 #2 #1 #0
2281 RDPRR
RDPRR (#2) Type of regeneration
0: electric power regeneration
1: resistance regeneration
*)There is no regeneration power from amplifier to power supply for the regeneration resistance type
amplifier.
Therefore the instantaneous power of Electric Power Consumption Monitor must be big than 0.
Refer the following table for loss coefficinet of βiSVamplifiers.

Parameter No.
No.2469 No.2490 No.2463 No.2491
Amplifier B C D
Spec A
HRV2 HRV3
621
βiSV4 6130-H001 960 320 416 0
(1024)*
621
βiSV20 6130-H002 960 320 416 0
(1024)*
βiSV40 6130-H003 960 294 378 0 646
βiSV80 6130-H004 960 275 371 0 646

512 320 416
βiSV20/20 6136-H201
416
0 710
512 320
512 288 365
βiSV40/40 6136-H203
365
0 710
512 288
βiSV10HV 6131-H001 960 525 947 0 320
βiSV20HV 6131-H002 960 563 928 0 320
βiSV40HV 6131-H003 960 563 979 0 320

*) For single phase use
For other parameters setting details, please refer technical report TMN09/074 (A-92737E Edition 02 )
[FS30i /31i /32i-A, 31i-A5 Power consumption monitoring (Edition 02)]
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
Power Supply
Module
αiF 22/3000 297
A06B-6140-Hxxx
A06B-6117-Hxxx
αiS 1000/2000 HV 458
(A06B-0098-Bxxx)
αiS 2000/2000 HV 459 A06B-6127-Hxxx A06B-6150-Hxxx
αiS 3000/2000 HV 460
Power Supply
Module
αiS 300/3000HV 344

400VDriver 400VDriver
αiS 500/3000HV 347 A06B-6127-Hxxx A06B-6150-Hxxx
αiS 1000/3000HV 465
αiS 4/6000 466 High speed model

αiS 4/6000HV 467 for Live Tool
αiS 50/2000 468

driven by
αiS 60/2000 470 160A and 80A(HV)amplifier
αiS 60/2000HV 471
αiS 60/3000 with Fan 328 High power model
driven by 360A and 180A(HV)
αiS 60/3000HV with Fan 329 amplifier
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
Motor model
αiF22 αiS60 αiS60 αiS300 αiS500
3000 3000Fan 3000HVFan 3000HV 3000HV
Motor ID number 297 328 329 344 347
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 01000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00001000 00001000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00100000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00000000 00001010 00001010 00011010 00011010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 1750 1191 1131 821 1344
PK2 2041 -6000 -6320 -5966 -5450 -7296
PK3 2042 -1345 -1347 -1345 -1355 -1357
PK1V 2043 198 69 69 91 111
PK2V 2044 -1775 -617 -617 -819 -996
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 2137 6152 6152 4633 3811
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 0 0 0 4200 4200
PPMAX 2053 21 31979 31979 21 21
PDDP 2054 1894 3 3 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0
PVPA 2057 -5136 -4619 -4620 -5646 -3856
PALPH 2058 -2800 -2000 -2000 -1800 -2900
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32520 32388 32388 32380 32380
POVC2 2063 3101 4744 4745 4850 4850
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 9224 14138 14140 12155 12155
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 12288 8192 4096 12288 12288
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 2131 1937 1937 2000 2482
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 15000 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 929 4411 4411 13494 18125
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 1291 519 519 523 521
DETQLM 2111 0 5220 5220 2960 2953
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 3272 2852 5393 7720 8021
MFWKCE 2128 4500 5000 3000 4300 2500
MFWKBL 2129 1301 1300 1300 1556 1041
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 5150 5150 3100 3093
PHDLY2 2134 0 8990 8990 6422 6418
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 140 140
POVC21 2162 32765 32742 32742 32700 32700
POVC22 2163 40 327 327 853 853
POVCLMT2 2164 7229 5973 5974 10644 10644
MAXCRT 2165 85 365 185 0 0
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 29 32
DCIDBS 2310 1817 0 0 1700 1400
TQLMSV 2302 0 0 0 20 20
TQLMST 2316 0 0 0 5394 5394
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
Motor model
2000HV 2000HV 2000HV 3000HV 6000 6000HV 2000 2000HV 2000 2000HV
Motor ID number 458 459 460 465 466 467 468 469 470 471
symbol FS30i,31i,32i
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 01000011 01000011 01000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00001000 00000000 00000000 00001000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00011010 10011110 10011010 10011010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 11000000 11000000 10000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1260 643 772 960 395 432 1539 1539 1358 1358
PK2 2041 -8010 -3600 -3819 -6554 -1606 -1673 -7321 -7321 -6767 -6767
PK3 2042 -1362 -1358 -1357 -1362 -1277 -1266 -1344 -1344 -1344 -1344
PK1V 2043 263 502 652 191 76 77 90 90 103 103
PK2V 2044 -2357 -4500 -5836 -1708 -678 -688 -802 -802 -925 -925
PK3V 2045 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 1610 843 650 2221 5601 5516 4731 4731 4103 4103
BLCMP 2048 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510
RESERV 2052 3500 0 0 4200 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 31979 31979 31979 31979
PDDP 2054 3787 3787 3787 1894 1894 1894 3 3 3 3
PHYST 2055 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0
PVPA 2057 -2320 -3363 -2088 -4620 -13326 -13326 -3867 -3867 -3097 -3097
PALPH 2058 -2500 -3200 -5000 -2500 -2500 -2500 -3393 -3393 -2995 -2995
PPBAS 2059 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32309 32309 32309 32488 32310 32288 32515 32501 32515 32501
POVC2 2063 5734 5734 5734 3503 5728 5995 3166 3332 3166 3332
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 27346 27346 27346 18280 17091 17893 9418 9912 9418 9912
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0
AALPH 2074 12288 12288 12288 12288 16384 16384 8192 8192 0 0
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 2960 2893 3187 2599 2585 2586 1856 1856 2018 2018
TDPLD 2087 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 2800 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 27963 5957 8472 3807 104 104 2569 2569 2942 2942
LP24PA 2106 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 785 784 267 1040 3092 3092 1032 1032 1544 1544
DETQLM 2111 2300 2022 2218 3242 8208 8208 4954 4954 3151 3151
AMRDML 2112 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 11851 3449 3029 9876 660 1368 2825 5651 5498 5498
MFWKCE 2128 4500 3000 2700 4500 3000 3000 4601 4601 4004 4004
MFWKBL 2129 1038 1291 777 1556 4365 4365 1296 1296 1302 1302
LP2GP 2130 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 2570 2060 2068 2580 7690 7690 2570 2570 4146 4146
PHDLY2 2134 12810 12820 6410 6418 12830 12830 12814 12814 12821 12821
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 140 140 140 140 0 0 128 0 128 0
POVC21 2162 32745 32745 32745 32721 32763 32763 32764 32764 32761 32764
POVC22 2163 292 292 292 589 58 63 51 48 81 51
POVCLMT2 2164 13952 13952 13952 13952 9912 10651 6831 6829 8124 7077
MAXCRT 2165 365 365 365 365 25 10 165 85 165 85
ACCBSLM 2304 0 2720 0 0 0 0 0 0 0 0
ACDCEND 2305 22 4112 22 29 0 0 0 0 0 0
DCIDBS 2310 1112 1236 1112 1648 0 0 0 0 0 0
TQLMSV 2302 0 0 0 0 0 0 0 0 0 0
TQLMST 2316 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i, 31i, 32i -A(90E1)
DRAW. No. CUST.
SHEET
Notice of the correction of wrong description for Velocity Integrator copy function in
SERVO MOTOR Parameter manual

Parameter manual

Correct, Del Date
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction ・ Correction of wrong description for Velocity Correct 2010.05

Integrator copy function
Another
TITLE
Notice of Correct of wrong descriptionfor
Velocity Integrator copy function in SERVO
MOTOR Parameter manual
DRAW. No. CUST.
01 2010.05.20 K.Maeda Newly designed B-65270EN/07-027
SHEET
Corrected point
TITLE
Notice of Correct of wrong descriptionfor
Velocity Integrator copy function in SERVO
MOTOR Parameter manual
DRAW. No. CUST.
01 2010.05.20 K.Maeda Newly designed B-65270EN/07-027
SHEET

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Changes of Standard Parameter Table Add 2010.06
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E0 29.0

3. Attached
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
(1) N2052 has been added for servo alarm SV649 that is detected when the motor rotates over its
maximum speed by wrong velocity command or other reasons.
Motor model
4000HV 5000 4000 SVSP40A 5000 4000 SVSP40A 3000 SVSP40A 5000 5000
Motor ID number 251 252 253 254 255 256 257 258 259 260 261
OSPLV 2052 5600 7000 5600 5600 7000 5600 5600 4200 4200 7000 7000
Motor model
αiS2 αiS2 βi S4 αiS4 αiS4 βi S8 βi S12/2000 βiS12 βiS12 αC4 βiS12
5000 5000HV 4000HV 5000 5000HV 3000HV SVSP 40A 2000 3000HV 3000i 3000
Motor ID number 262 263 264 265 266 267 268 269 270 271 272
OSPLV 2052 7000 7000 5600 7000 7000 4200 2800 2800 4200 4200 4200
Motor model
αiF4 βiS22 αiF4 αC8 αiF8 βi S22 αiF8 βiS0.4 βiS0.5 βiS1 αiS2
4000 2000 4000HV 2000i 3000 2000HV 3000HV 5000 6000 6000 6000
Motor ID number 273 274 275 276 277 278 279 280 281 282 284
OSPLV 2052 5600 2800 5400 2800 4200 2700 3900 7000 7500 7500 7500
Motor model
αiS8 αiS8 αiS2 αiS12 αiS12 αiS8 αC12 αiS8 αiF12 αiF12 αC22
4000 4000HV 6000HV 4000 4000HV 6000 2000i 6000HV 3000 3000HV 2000i
Motor ID number 285 286 287 288 289 290 291 292 293 295 296
OSPLV 2052 5600 5600 7500 5600 5600 7500 2800 7500 4800 4800 2400
Motor model
αiF22 αiF22 αC30 αiF30 αiF40 αiF40 βiS22 βiS22 αiS22 αiS22 αiS30
3000 3000HV 1500i 3000 3000 3000Fan 3000 3000HV 4000 4000HV 4000
Motor ID number 297 299 301 303 307 308 313 314 315 316 318
OSPLV 2052 3600 3600 2100 4800 4200 4200 4200 4200 5600 5600 5400
αiS100
Motor model 2500HVFa
4000HV 4000 4000HV 3000 3000Fan 3000HVFan 3000HV 3000Fan 3000HVFan 2500Fan n
Motor ID number 319 322 323 324 325 326 327 328 329 330 331
OSPLV 2052 5400 4800 4800 4200 4200 4200 4200 4000 4000 3500 3500
Motor model
2500Fan 2500 2500HV 2500HVFan 2500 2500HV 2000HV 2000 2000HV 3000HV 2000
Motor ID number 334 335 336 337 338 339 340 342 343 344 345
OSPLV 2052 3100 3500 3500 3100 3100 3100 2400 2800 2800 3900 2400
αiS1000
Motor model 3000HV
2000HV 3000HV 2000HV 6000 6000HV 2000HV 2000HV 2000HV 2000HV 2000HV
PDM あり
Motor ID number 346 347 348 350 452 453 454 455 458 459 460
OSPLV 2052 2400 4200 2600 3800 7500 7500 2400 2800 2600 2400 2800
αiS1000
αiS12 αiS12 αiS4 αiS4 αiS50 αiS50 αiS60 αiS60
Motor model 3000HV
6000 6000HV 6000 6000HV 2000 2000HV 2000 2000HV
PDM なし
Motor ID number 462 463 465 466 467 468 469 470 471
OSPLV 2052 7500 7500 3800 7500 7500 2800 2800 2700 2700
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
(2) 2000/min model of βis series Servo motors have been added.
βiS 30/2000V 472 -
400VDriver
βiS 30/2000HV 473
βiS 40/2000V 474 -

400VDriver
βiS 40/2000HV 475
* Please refer to Table1 about the new added standard parameters.
(3) Following models are added in Lis series.
LiS 10000C3/2HV 395 400V Driver

* Please refer to Table 1 about the new added standard parameters.
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
LiS10000
βiS30 βiS30 βiS40 βi S40
Motor Model C3/2HV
2000 2000HV 2000 2000HV
(400V)
Motor specification 0457-B010 0087 0088 0089 0090
Motor ID Number 395 472 473 474 475
Symbol FS30i,31i,32i,
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000100 00000010 00000010 00000010 00000010
2014 00000100 00000010 00000010 00000010 00000010
2210 00000000 00000000 00000000 00000000 00000000
2211 00001000 00001010 00001010 00001010 00001010
2300 10000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 3010 1650 1650 1624 1624
PK2 2041 -6519 -6565 -6565 -7197 -7197
PK3 2042 -2695 -2681 -2681 -1341 -1341
PK1V 2043 10 214 214 208 208
PK2V 2044 -129 -1912 -1912 -1870 -1870
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 -8849 3971 3971 4057 4057
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
OSPLV 2052 0 2800 2800 2600 2600
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0
PVPA 2057 0 -4647 -4647 -3375 -3375
PALPH 2058 0 -3115 -3115 -3862 -3862
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 6554 6554 6554 6554
EMFLMT 2061 120 0 0 0 0
POVC1 2062 32722 32413 32413 32413 32413
POVC2 2063 576 4431 4431 4431 4431
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 1707 13201 13201 13201 13201
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 -4096 8192 8192 8192 8192
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 961 2154 2154 2154 2154
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 2043 1127 1127 1503 1503
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 0 1546 1546 263 263
DETQLM 2111 0 4255 4255 3065 3065
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 0 2095 2095 2712 2712
MFWKCE 2128 0 3066 3066 3354 3354
MFWKBL 2129 0 1548 1548 1038 1038
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 4110 4110 2567 2567
PHDLY2 2134 0 12814 12814 8967 8967
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 0 32765 32765 32765 32765
POVC22 2163 0 34 34 36 36
POVCLMT2 2164 0 7387 7387 7713 7713
MAXCRT 2165 85 85 45 85 45
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0
TQLMSV 2302 0 0 0 0 0
TQLMST 2316 0 0 0 0 0
TITLE
Series 30i, 31i, 32i -A(90E0)
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i / 31i / 32i (90E1)

PARAMETER MANUAL

Correct, Del Date
Basic Function Changes of Standard parameter table Add 2010. 09
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 30i/ 32i(90E1)
1. Update Edition
FS30i, 31i, 32i -A
90E1 05.0
(For SERVO HRV2 and HRV3 Control)
Four new models for βiS series motor and one new model for LiS series motor have been added.
Furthermore parameter No.2052 has been added in order to detect servo alarm SV649 when the motor
rotates over its maximum speed by wrong command or other reasons.
Please refer to the Technical Report TMS 10/044(B-65270EN/07-028) “Notice of the Update of Digital
Servo Software for Series 30i/ 31i/ 32i (90E0)” for the details.
TITLE
Notice of the Update of Digital Servo Software for Series
30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET

PARAMETER MANUAL

Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
DRAW. No. CUST.
SHEET
1. Update Edition
90BP 07
3. Attached
TITLE
DRAW. No. CUST.
01 10.08.25 Tang Newly designed
B-65270EN/07-030
Ed Date Design Description SHEET
02／05
Attached 1.Changes of Standard Parameter Table
(1) N2052 has been added for servo alarm SV649 that is detected when the motor rotates over its
maximum speed by wong velocity command or other reasons.
Motor model 4000HV 5000 4000 SVSP40A 5000 4000 SVSP40A 3000 SVSP40A 5000 5000
Motor specification0062 0202 0061 0061 0205 0063 0063 0075 0075 0111 0112
Motor ID numbe 251 252 253 254 255 256 257 258 259 260 261
r
OSPLV 1864 2052 5600 7000 5600 5600 7000 5600 5600 4200 4200 7000 7000
αiS2 αiS2 βi S4 αiS4 αiS4 βi S8 βi S12/2000 βiS12 βiS12 αC4 βiS12

Motor model 5000 5000HV 4000HV 5000 5000HV 3000HV SVSP 40A 2000 3000HV 3000i 3000
Motor ID numbe 262 263 264 265 266 267 268 269 270 271 272
r
OSPLV 1864 2052 7000 7000 5600 7000 7000 4200 2800 2800 4200 4200 4200
αiF4 βi S22 αiF4 αC8 αiF8 βi S22 αiF8 βiS0.4 βiS0.5 βiS1 αiS2
Motor model 4000 2000 4000HV 2000i 3000 2000HV 3000HV 5000 6000 6000 6000
Motor ID numbe 273 274 275 276 277 278 279 280 281 282 284
r
OSPLV 1864 2052 5600 2800 5400 2800 4200 2700 3900 7000 7500 7500 7500
αiS8 αiS8 αiS2 αiS12 αiS12 αiS8 αC12 αiS8 αiF12 αiF12 αC22
Motor model 4000 4000HV 6000HV 4000 4000HV 6000 2000i 6000HV 3000 3000HV 2000i
Motor ID numbe 285 286 287 288 289 290 291 292 293 295 296
r
OSPLV 1864 2052 5600 5600 7500 5600 5600 7500 2800 7500 4800 4800 2400
αiF22 αiF22 αC30 αiF30 αiF40 αiF40 βiS22 βiS22 αiS22 αiS22 αiS30
Motor model 3000 3000HV 1500i 3000 3000 3000Fan 3000 3000HV 4000 4000HV 4000
Motor ID numbe 297 299 301 303 307 308 313 314 315 316 318
r
OSPLV 1864 2052 3600 3600 2100 4800 4200 4200 4200 4200 5600 5600 5400
αiS100
Motor model 4000HV 2500HVFa
4000 4000HV 3000 3000Fan 3000HVFan 3000HV 3000Fan 3000HVFan 2500Fan n
Motor ID numbe 319 322 323 324 325 326 327 328 329 330 331
r
OSPLV 1864 2052 5400 4800 4800 4200 4200 4200 4200 4000 4000 3500 3500
Motor model 2500Fan 2500 2500HV 2500HVFan 2500 2500HV 2000HV 2000 2000HV 3000HV 2000
Motor ID numbe 334 335 336 337 338 339 340 342 343 344 345
r
OSPLV 1864 2052 3100 3500 3500 3100 3100 3100 2400 2800 2800 3900 2400
αiS1000
Motor model 2000HV 3000HV
3000HV 2000HV 6000 6000HV 2000HV 2000HV 2000HV 2000HV 2000HV
PDM あり
Motor ID numbe 346 347 348 350 452 453 454 455 458 459 460
r
OSPLV 1864 2052 2400 4200 2600 3800 7500 7500 2400 2800 2600 2400 2800
αiS1000
αiS12 αiS12 αiS4 αiS4 αiS50 αiS50 αiS60 αiS60
Motor model 3000HV
6000 6000HV 6000 6000HV 2000 2000HV 2000 2000HV
PDM なし
Motor ID numbe 462 463 465 466 467 468 469 470 471
r
OSPLV 1864 2052 7500 7500 3800 7500 7500 2800 2800 2700 2700
TITLE
DRAW. No. CUST.
B-65270EN/07-030
03／05
(2) 2000/min model of βis series Large Servo motors have been added.
βiS 30/2000V 472 -
400VDriver
βiS 30/2000HV 473
βiS 40/2000V 474 -

400VDriver
βiS 40/2000HV 475
(3) Following model is added in Lis series.
LiS 10000C3/2HV 395 400V Driver
TITLE
DRAW. No. CUST.
B-65270EN/07-030
04／05
Table1) Standard parameter table for new added models.
L10000
βiS30 βiS30 βiS40 βiS40
Motor model C3/2HVis
2000 2000HV 2000 2000HV
(400V)
Motor specification 0457-B010 0087 0088 0089 0090
Motor ID number 395 472 473 474 475
1808 2003 00001000 00001000 00001000 00001000 00001000
1809 2004 00000011 00000011 00000011 00000011 00000011
1883 2005 00000000 00000000 00000000 00000000 00000000
1884 2006 00000000 00000000 00000000 00000000 00000000
1951 2007 00000000 00000000 00000000 00000000 00000000
1952 2008 00000000 00000000 00000000 00000000 00000000
1953 2009 00000000 00000000 00000000 00000000 00000000
1954 2010 00000100 00000000 00000000 00000000 00000000
1955 2011 00000000 00000000 00000000 00000000 00000000
1956 2012 00000000 00000000 00000000 00000000 00000000
1707 2013 00000100 00000010 00000010 00000010 00000010
1708 2014 00000100 00000010 00000010 00000010 00000010
1750 2210 00000000 00000000 00000000 00000000 00000000
1751 2211 00001000 00001010 00001010 00001010 00001010
2713 2300 10000000 00000000 00000000 00000000 00000000
2714 2301 00000000 00000000 00000000 00000000 00000000
PK1 1852 2040 3010 1650 1650 1624 1624
PK2 1853 2041 -6519 -6565 -6565 -7197 -7197
PK3 1854 2042 -2695 -2681 -2681 -1341 -1341
PK1V 1855 2043 10 214 214 208 208
PK2V 1856 2044 -129 -1912 -1912 -1870 -1870
PK3V 1857 2045 0 0 0 0 0
PK4V 1858 2046 -8235 -8235 -8235 -8235 -8235
POA1 1859 2047 -8849 3971 3971 4057 4057
BLCMP 1860 2048 0 0 0 0 0
DPFMX 1861 2049 0 0 0 0 0
POK1 1862 2050 956 956 956 956 956
POK2 1863 2051 510 510 510 510 510
RESERV 1864 2052 0 2800 2800 2600 2600
PPMAX 1865 2053 21 21 21 21 21
PDDP 1866 2054 1894 1894 1894 1894 1894
PHYST 1867 2055 319 319 319 319 319
EMFCMP 1868 2056 0 0 0 0 0
PVPA 1869 2057 0 -4647 -4647 -3375 -3375
PALPH 1870 2058 0 -3115 -3115 -3862 -3862
PPBAS 1871 2059 0 0 0 0 0
TQLIM 1872 2060 7282 6554 6554 6554 6554
EMFLMT 1873 2061 120 0 0 0 0
POVC1 1877 2062 32722 32413 32413 32413 32413
POVC2 1878 2063 576 4431 4431 4431 4431
TGALMLV 1892 2064 4 4 4 4 4
POVCLMT 1893 2065 1707 13201 13201 13201 13201
PK2VAUX 1894 2066 0 0 0 0 0
FILTER 1895 2067 0 0 0 0 0
FALPH 1961 2068 0 0 0 0 0
VFFLT 1962 2069 0 0 0 0 0
ERBLM 1963 2070 0 0 0 0 0
PBLCT 1964 2071 0 0 0 0 0
SFCCML 1965 2072 0 0 0 0 0
PSPTL 1966 2073 0 0 0 0 0
AALPH 1967 2074 -4096 8192 8192 8192 8192
OSCTPL 1970 2077 0 0 0 0 0
PDPCH 1971 2078 0 0 0 0 0
PDPCL 1972 2079 0 0 0 0 0
DPFEX 1973 2080 0 0 0 0 0
DPFZW 1974 2081 0 0 0 0 0
BLENDL 1975 2082 0 0 0 0 0
MOFCTL 1976 2083 0 0 0 0 0
RTCURR 1979 2086 961 2154 2154 2154 2154
TDPLD 1980 2087 0 0 0 0 0
MCNFB 1981 2088 0 0 0 0 0
BLBSL 1982 2089 0 0 0 0 0
ROBSTL 1983 2090 0 0 0 0 0
ACCSPL 1984 2091 0 0 0 0 0
ADFF1 1985 2092 0 0 0 0 0
VMPK3V 1986 2093 0 0 0 0 0
BLCMP2 1987 2094 0 0 0 0 0
AHDRTL 1988 2095 0 0 0 0 0
RADUSL 1989 2096 0 0 0 0 0
SMCNT 1990 2097 0 0 0 0 0
DEPVPL 1991 2098 0 0 0 0 0
ONEPSL 1992 2099 400 400 400 400 400
INPA1 1993 2100 0 0 0 0 0
INPA2 1994 2101 0 0 0 0 0
DBLIM 1995 2102 0 0 0 0 0
ABVOF 1996 2103 0 0 0 0 0
ABTSH 1997 2104 0 0 0 0 0
TRQCST 1998 2105 2043 1127 1127 1503 1503
LP24PA 1999 2106 0 0 0 0 0
VLGOVR 1700 2107 0 0 0 0 0
RESERV 1701 2108 0 0 0 0 0
BELLTC 1702 2109 0 0 0 0 0
MGSTCM 1703 2110 0 1546 1546 263 263
DETQLM 1704 2111 0 4255 4255 3065 3065
AMRDML 1705 2112 0 0 0 0 0
NFILT 1706 2113 0 0 0 0 0
NINTCT 1735 2127 0 2095 2095 2712 2712
MFWKCE 1736 2128 0 3066 3066 3354 3354
MFWKBL 1752 2129 0 1548 1548 1038 1038
LP2GP 1753 2130 0 0 0 0 0
LP4GP 1754 2131 0 0 0 0 0
LP6GP 1755 2132 0 0 0 0 0
PHDLY1 1756 2133 0 4110 4110 2567 2567
PHDLY2 1757 2134 0 12814 12814 8967 8967
DGCSMM 1782 2159 0 0 0 0 0
TRQCUP 1783 2160 0 0 0 0 0
OVCSTP 1784 2161 0 0 0 0 0
POVC21 1785 2162 0 32765 32765 32765 32765
POVC22 1786 2163 0 34 34 36 36
POVCLMT2 1787 2164 0 7387 7387 7713 7713
MAXCRT 1788 2165 85 85 45 85 45
ACCBSLM 2717 2304 0 0 0 0 0
ACDCEND 2718 2305 0 0 0 0 0
DCIDBS 2723 2310 0 0 0 0 0
TQLMSV 2715 2302 0 0 0 0 0
TQLMST 2729 2316 0 0 0 0 0
TITLE
DRAW. No. CUST.
B-65270EN/07-030
05／05

PARAMETER MANUAL

Correct, Del Date
Basic Function - Supporting Detection of EXCESS ERROR from Add 2010. 10
Estimated Position to Actual Position on Dual
Position Feedback
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E1 06.0
- Supporting Detection of EXCESS ERROR from Estimated Position to Actual Position
on Dual Position Feedback
“Detection of EXCESS ERROR from Estimated Position to Actual Position at Dual Position
Feedback “ has been supported from this version.
However, since the characteristic of dual position feedback is not considered during the
presumption, the presumed error will occur according to a mechanical torsion and a time
constant of dual potion feedback. So a larger alarm level is need to set in this case.
To use "Detection of EXCESS ERROR from Estimated Position to Actual Position at Dual
Position Feedback" the following parameters have to be set.
For details please refer to the Technical Report TMS 10/003 (B-65270EN/07-022 )
“Detection of EXCESS ERROR from Estimated Position to Actual Position ”.
#7 #6 #5 #4 #3 #2 #1 #0
2420 (FS30i) DUDYN
DUDYN (#4) Detection of Excessive error (SV) alarm in Dual Postion Feedbak is
0: Disable
1: Enable
Reference parameter
#7 #6 #5 #4 #3 #2 #1 #0
2419 (FS30i) DYNTQL DYNERR
DYNERR(#0) Detection of Excessive error (SV) alarm is
0: Disable
1: Enable
If DYNERR=1 is used with a CNC that does not support the function,
an illegal parameter setting alarm (detail number 4190) is issued.
DYNTQL(#1) Detection of Excessive error alarm during the torque limit is
0: Enable
1: Disable
2458 (FS30i) EXCESS ERROR detection level

[Valid data range] from 0 to 32767
[Typical setting] 0.2 times of position error in rapid traverse
TITLE
Notice of the Update of Digital Servo Software for Series
30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Improving Power Consumption Monitor Function New 2010.12
2. Improving Inertia Estimation Function
3. Supporting Detection of EXCESS ERROR from New 2010.12
Estimated Position to Actual Position on Dual
Position Feedback mode too New 2010.12
4. Changes of Standard Parameter Table
Add 2010.12
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E0 30.0
- Improving Power Consumption Monitor Function
Power Consumption Monitor for βiSV amplifier has been supported.
Power Consumption Monitor for Linear Motor and Synchronous Bulit-in Servo Motor has
been supported.
Please refer to Technical Report TMS10/016 (B-65270EN/07-025) “ Notice of the Update of

Digital Servo Software for Series 30i, 31i, 32i -A(90E1) ” and
A-92737 “FANUC Series 30i -A /31i -A5 /31i -A /32i -A Power Consumption Monitor
Specifications ” for details.
- Improving Inertia Estimation Function

Inertia Estimation function has been improved so that even large inertia is correctly
detected by increasing the detective sensitivity. Besides “Tandem Control” has been also
available.
For the detailed information, please refer to Technical Report TMS10/007

(B-65270EN/07-024) “Operation manual for Inertia Estimation function”.
- Supporting Detection of EXCESS ERROR from Estimated Position to Actual Position

on Dual Position Feedback mode too
Detection of EXCESS ERROR from Estimated Position to Actual Position also can be
used at Dual Position Feedback mode from this version.
For details please refer to the Technical Report TMS 10/075 (B-65270EN/07-031 )
“Notice of the Update of Digital Servo Software for Series 30i / 30i / 32i(90E1) ”

3. Attached
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET
(1) New models for DiS series servo motor have been added.
-The following motors are driven by 200V.

Motor Model Motor Specification Motor ID No.
DiS15/1000 0492-B100 551

DiS60/400 0493-B200 553
DiS70/300 0494-B100 555
DiS150/300 0494-B300 557
DiS200/300 0494-B400 559
DiS250/250 0495-B200 561
DiS400/250 0485-B20x 419
DiS500/250 0495-B400 563
DiS800/250 0485-B40x 433
DiS1000/200 0496-B300 565
DiS1500/100 0497-B300 567
DiS2000/100 0497-B400 569
DiS2000/150 0497-B490 571
* Please refer to Table1, 2, 3 about the standard parameters.

DiS15/1000 0492-B100 552

DiS60/400 0493-B200 554
DiS70/300 0494-B100 556
DiS150/300 0494-B300 558
DiS200/300 0494-B400 560
DiS250/250 0495-B200 562
DiS400/250 0485-B20x 420
DiS500/250 0495-B400 564
DiS800/250 0485-B40x 434
DiS1000/200 0496-B300 566
DiS1500/100 0497-B300 568
DiS2000/100 0497-B400 570
DiS2000/150 0497-B490 572
DiS5000/50 0488-B400 573
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET
Motor model DiS400 DiS400 DiS800/ DiS800/ DiS15 DiS15 DiS60 DiS60 DiS70 DiS70 DiS150
/250 /250 250 250 /1000 /1000 /400 /400 /300 /300 /300
(200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V)
Motor Specification 0485-B20x 0485-B20x 0485-B40x 0485-B40x 0492-B100 0492-B100 0493-B200 0493-B200 0494-B100 0494-B100 0494-B300
Motor ID Number 419 420 433 434 551 552 553 554 555 556 557
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000010 00000000 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
2014 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
BITP12 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00000000 00000000 00011000 00001000 00001000 00001000 00001000 00001000 00001000
BITP35 2300 10000110 10000110 10000100 10000100 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 494 494 738 496 309 154 538 269 296 148 379
PK2 2041 -1949 -1352 -2500 -1588 -1713 -857 -3794 -1897 -2764 -1382 -3215
PK3 2042 -2943 -2943 -2996 -2996 -3067 -3067 -3102 -3102 -3117 -3117 -3128
PK1V 2043 415 415 386 343 69 69 86 86 180 180 149
PK2V 2044 -3713 -3713 -3461 -3076 -618 -618 -772 -772 -1614 -1614 -1331
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 2271 2271 2437 2742 13637 13637 10929 10929 5224 5224 6336
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 720 1200 240 480 180 360 180
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 5648 5020 7282 7282 5462 5462 6190 6190 6190
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32743 32743 32713 32713 32675 32675 32675 32675 32684 32684 32714
POVC2 2063 308 308 690 690 1160 1160 1160 1160 1056 1056 679
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 903 903 1200 948 3300 3300 1856 1856 2178 2178 1419
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 20480 20480 0 0 -20480 -20480 -32768 -32768 -24576 -24576 -20480
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 753 753 868 772 1440 1440 845 845 1005 1005 944
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 8080 8080 16519 18584 612 612 2865 2865 3521 3521 7830
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1281 1281 0 0 2305 2049 1793 1793 1793 1793 1793
DETQLM 2111 1535 0 0 0 8854 0 6174 0 5173 0 5173
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 16776 0 0 0 16000 0 4000 0 0 0 4000
MFWKBL 2129 14 0 0 0 277 0 6158 0 0 0 5134
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 120 120 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 165 185 25 25 45 45 45 45 85
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 72 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET
Motor model DiS150 DiS200 DiS200 DiS250 DiS250 DiS500 DiS500 DiS1000 DiS1000 DiS1500 DiS1500
/300 /300 /300 /250 /250 /250 /250 /200 /200 /100 /100
(400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V)
Motor Specification 0494-B300 0494-B400 0494-B400 0495-B200 0495-B200 0495-B400 0495-B400 0496-B300 0496-B300 0497-B300 0497-B300
Motor ID Number 558 559 560 561 562 563 564 565 566 567 568
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
2014 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
BITP12 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00011000 00011000 00001000 00001000 00001000 00001000 00011000 00001000 00011000 00001000
BITP35 2300 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10010100 10010100 10000000 10000000
PK1 2040 189 451 226 294 158 321 181 434 244 490 276
PK2 2041 -1607 -3966 -1983 -2458 -1150 -2569 -1445 -2352 -1323 -3676 -2068
PK3 2042 -3128 -3135 -3135 -3129 -3129 -3138 -3138 -3173 -3173 -3176 -3176
PK1V 2043 149 141 141 334 334 297 264 558 496 760 676
PK2V 2044 -1331 -1261 -1261 -2996 -2996 -2664 -2368 -4997 -4442 -6812 -6055
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 6336 6686 6686 2815 2815 3165 3561 1688 1899 1238 1393
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 360 180 360 150 300 150 300 120 240 60 120
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 -11264 0 -11264 0 -11264
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 6190 6190 6190 7282 7282 7282 6473 7282 6473 7282 6473
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32714 32721 32721 32707 32707 32723 32723 32677 32677 32682 32682
POVC2 2063 679 590 590 761 761 567 567 1135 1135 1078 1078
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 1419 1237 1237 2196 2196 1646 1301 3231 2553 3076 2430
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 -20480 -4096 -4096 -4096 -8192 20480 20480 -20480 -20480 28672 28672
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 944 881 881 1175 1175 1062 944 1421 1266 1390 1235
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 7830 11266 11266 10329 10329 20150 22669 3349 3768 5516 6206
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1793 1793 1793 1793 1793 2049 2049 2049 2305 2049 2049
DETQLM 2111 0 2625 7710 3890 12900 3890 11311 2680 6229 1184 3212
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 0 6000 0 7000 0 5000 0 10000 0 5000 0
MFWKBL 2129 0 2581 0 3861 0 3861 0 2588 0 1042 0
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 85 85 85 165 185 165 185 165 185
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 36 72 0 0 0 0 24 0 12 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET
Motor model DiS2000 DiS2000 DiS2000 DiS2000 DiS5000
/100 /100 /150 /150 /50
(200V) (400V) (200V) (400V) (400V)
Motor Specification 0497-B400 0497-B400 0497-B490 0497-B490 0488-B400
Motor ID Number 569 570 571 572 573
INTST 2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000
2006 00000010 00000010 00000010 00000010 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000100 00000100 00000100 00000000
2014 00000000 00000100 00000100 00000100 00000000
BITP12 2210 00000100 00000100 00000100 00000100 00000100
2211 00011000 00011000 00001000 00001000 00011000
BITP35 2300 10000110 10000110 10000110 10000110 10000110
2301 10000000 10000000 10000000 10000000 10010100
PK1 2040 637 358 448 224 417
PK2 2041 -5353 -3011 -3457 -1729 -3875
PK3 2042 -3177 -3177 -3177 -3177 -3181
PK1V 2043 689 612 620 620 1096
PK2V 2044 -6171 -5485 -5554 -5554 -9817
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 1367 1537 1518 1518 859
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 60 120 90 180 60
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 -11264 0 0 0
PVPA 2057 -1038 -2054 0 0 -527
PALPH 2058 -489 -430 0 0 -665
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 6473 6473 6473 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32709 32709 32707 32707 32731
POVC2 2063 740 740 763 763 459
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 2136 1688 1739 1739 1337
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 24576 24576 12288 12288 24576
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 1176 1045 1045 1045 916
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 8086 9097 8984 8984 22101
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 2049 2049 2049 2049 1793
DETQLM 2111 1244 2161 2218 4727 767
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 0 0 0 0 0
MFWKCE 2128 15000 0 10000 0 16000
MFWKBL 2129 1042 0 2069 0 540
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 0 0 0 0 0
POVC22 2163 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0
MAXCRT 2165 165 185 365 365 185
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 12 24 0 0 12
DCIDBS 2310 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E0)
DRAW. No. CUST.
SHEET

PARAMETER MANUAL

Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
1. Update Edition
FS30i, 31i, 32i -A
90E1 07.0

3. Attached
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET

DiS15/1000 0492-B100 551

DiS60/400 0493-B200 553
DiS70/300 0494-B100 555
DiS150/300 0494-B300 557
DiS200/300 0494-B400 559
DiS250/250 0495-B200 561
DiS400/250 0485-B20x 419
DiS500/250 0495-B400 563
DiS800/250 0485-B40x 433
DiS1000/200 0496-B300 565
DiS1500/100 0497-B300 567
DiS2000/100 0497-B400 569
DiS2000/150 0497-B490 571

DiS15/1000 0492-B100 552

DiS60/400 0493-B200 554
DiS70/300 0494-B100 556
DiS150/300 0494-B300 558
DiS200/300 0494-B400 560
DiS250/250 0495-B200 562
DiS400/250 0485-B20x 420
DiS500/250 0495-B400 564
DiS800/250 0485-B40x 434
DiS1000/200 0496-B300 566
DiS1500/100 0497-B300 568
DiS2000/100 0497-B400 570
DiS2000/150 0497-B490 572
DiS5000/50 0488-B400 573
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
Motor model DiS400 DiS400 DiS800/ DiS800/ DiS15 DiS15 DiS60 DiS60 DiS70 DiS70 DiS150
/250 /250 250 250 /1000 /1000 /400 /400 /300 /300 /300
(200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V)
Motor Specification 0485-B20x 0485-B20x 0485-B40x 0485-B40x 0492-B100 0492-B100 0493-B200 0493-B200 0494-B100 0494-B100 0494-B300
Motor ID Number 419 420 433 434 551 552 553 554 555 556 557
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000010 00000000 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
2014 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
BITP12 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00000000 00000000 00011000 00001000 00001000 00001000 00001000 00001000 00001000
BITP35 2300 10000110 10000110 10000100 10000100 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 494 494 738 496 309 154 538 269 296 148 379
PK2 2041 -1949 -1352 -2500 -1588 -1713 -857 -3794 -1897 -2764 -1382 -3215
PK3 2042 -2943 -2943 -2996 -2996 -3067 -3067 -3102 -3102 -3117 -3117 -3128
PK1V 2043 415 415 386 343 69 69 86 86 180 180 149
PK2V 2044 -3713 -3713 -3461 -3076 -618 -618 -772 -772 -1614 -1614 -1331
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 2271 2271 2437 2742 13637 13637 10929 10929 5224 5224 6336
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 720 1200 240 480 180 360 180
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 5648 5020 7282 7282 5462 5462 6190 6190 6190
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32743 32743 32713 32713 32675 32675 32675 32675 32684 32684 32714
POVC2 2063 308 308 690 690 1160 1160 1160 1160 1056 1056 679
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 903 903 1200 948 3300 3300 1856 1856 2178 2178 1419
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 20480 20480 0 0 -20480 -20480 -32768 -32768 -24576 -24576 -20480
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 753 753 868 772 1440 1440 845 845 1005 1005 944
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 8080 8080 16519 18584 612 612 2865 2865 3521 3521 7830
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1281 1281 0 0 2305 2049 1793 1793 1793 1793 1793
DETQLM 2111 1535 0 0 0 8854 0 6174 0 5173 0 5173
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 16776 0 0 0 16000 0 4000 0 0 0 4000
MFWKBL 2129 14 0 0 0 277 0 6158 0 0 0 5134
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 120 120 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 165 185 25 25 45 45 45 45 85
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 72 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
Motor model DiS150 DiS200 DiS200 DiS250 DiS250 DiS500 DiS500 DiS1000 DiS1000 DiS1500 DiS1500
/300 /300 /300 /250 /250 /250 /250 /200 /200 /100 /100
(400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V)
Motor Specification 0494-B300 0494-B400 0494-B400 0495-B200 0495-B200 0495-B400 0495-B400 0496-B300 0496-B300 0497-B300 0497-B300
Motor ID Number 558 559 560 561 562 563 564 565 566 567 568
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
2014 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
BITP12 2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00011000 00011000 00001000 00001000 00001000 00001000 00011000 00001000 00011000 00001000
BITP35 2300 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10010100 10010100 10000000 10000000
PK1 2040 189 451 226 294 158 321 181 434 244 490 276
PK2 2041 -1607 -3966 -1983 -2458 -1150 -2569 -1445 -2352 -1323 -3676 -2068
PK3 2042 -3128 -3135 -3135 -3129 -3129 -3138 -3138 -3173 -3173 -3176 -3176
PK1V 2043 149 141 141 334 334 297 264 558 496 760 676
PK2V 2044 -1331 -1261 -1261 -2996 -2996 -2664 -2368 -4997 -4442 -6812 -6055
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 6336 6686 6686 2815 2815 3165 3561 1688 1899 1238 1393
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 360 180 360 150 300 150 300 120 240 60 120
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 -11264 0 -11264 0 -11264
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 6190 6190 6190 7282 7282 7282 6473 7282 6473 7282 6473
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32714 32721 32721 32707 32707 32723 32723 32677 32677 32682 32682
POVC2 2063 679 590 590 761 761 567 567 1135 1135 1078 1078
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 1419 1237 1237 2196 2196 1646 1301 3231 2553 3076 2430
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 -20480 -4096 -4096 -4096 -8192 20480 20480 -20480 -20480 28672 28672
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 944 881 881 1175 1175 1062 944 1421 1266 1390 1235
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 7830 11266 11266 10329 10329 20150 22669 3349 3768 5516 6206
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1793 1793 1793 1793 1793 2049 2049 2049 2305 2049 2049
DETQLM 2111 0 2625 7710 3890 12900 3890 11311 2680 6229 1184 3212
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 0 6000 0 7000 0 5000 0 10000 0 5000 0
MFWKBL 2129 0 2581 0 3861 0 3861 0 2588 0 1042 0
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 85 85 85 165 185 165 185 165 185
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 36 72 0 0 0 0 24 0 12 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
Motor model DiS2000 DiS2000 DiS2000 DiS2000 DiS5000
/100 /100 /150 /150 /50
(200V) (400V) (200V) (400V) (400V)
Motor Specification 0497-B400 0497-B400 0497-B490 0497-B490 0488-B400
Motor ID Number 569 570 571 572 573
INTST 2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000
2006 00000010 00000010 00000010 00000010 00000010
BITPA2 2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000100 00000100 00000100 00000000
2014 00000000 00000100 00000100 00000100 00000000
BITP12 2210 00000100 00000100 00000100 00000100 00000100
2211 00011000 00011000 00001000 00001000 00011000
BITP35 2300 10000110 10000110 10000110 10000110 10000110
2301 10000000 10000000 10000000 10000000 10010100
PK1 2040 637 358 448 224 417
PK2 2041 -5353 -3011 -3457 -1729 -3875
PK3 2042 -3177 -3177 -3177 -3177 -3181
PK1V 2043 689 612 620 620 1096
PK2V 2044 -6171 -5485 -5554 -5554 -9817
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 1367 1537 1518 1518 859
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 60 120 90 180 60
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 -11264 0 0 0
PVPA 2057 -1038 -2054 0 0 -527
PALPH 2058 -489 -430 0 0 -665
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 6473 6473 6473 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32709 32709 32707 32707 32731
POVC2 2063 740 740 763 763 459
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 2136 1688 1739 1739 1337
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 24576 24576 12288 12288 24576
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 1176 1045 1045 1045 916
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 8086 9097 8984 8984 22101
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 2049 2049 2049 2049 1793
DETQLM 2111 1244 2161 2218 4727 767
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 0 0 0 0 0
MFWKCE 2128 15000 0 10000 0 16000
MFWKBL 2129 1042 0 2069 0 540
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 0 0 0 0 0
POVC22 2163 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0
MAXCRT 2165 165 185 365 365 185
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 12 24 0 0 12
DCIDBS 2310 0 0 0 0 0
TITLE
Series 30i/ 30i / 32i(90E1)
DRAW. No. CUST.
SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i-A (90E0)

PARAMETER MANUAL
New, Add Applicable
Group Name / Outline
Correct, Del Date
2. Improving the Semi-Full Error Observation Function Add 2011.02
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
名 Notice of the Update of Digital Servo Software
称 for Series 30i/ 31i/ 32i -A (90E0)
図提
番出
Ed. Date Design Description Page 1/4

Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i -A (90E0)
1. Update Edition
Series 30i/ 31i/ 32i -A
90E0 32.0
- Improving the Semi-Full Error Observation Function

This function monitors the "difference of detection position between motor built-in detector and
separate detector". It is effective to check normal operation of separate detector, and the monitoring of
"slip" between motor and machine. The following improvement is added.
- The unit of data in parameter of Semi-full error level (No.2118) can be chosen to “μm” unit.
Please refer to the Technical report B-65270EN/07-035 “Improving the Semi-Full Error Observation
Function)” for the details.
3. Attached
図提
番出

(1) New models for LiS series servo motor have been added.
LiS 4500B2/4 0446-B210 366

LiS9000C2/2HV 0454-B010 383
LiS 11000C2/4 0455-B210 390
- Please refer to Table1 about the standard parameters.
(2) αiS series servo motor have been added for Spindle use.

αiS2000/2000
0091 476
for Spindle use
- When using this parameter, please refor to B-65272JA/06 ”FANUC AC SPINDLE MOTOR
αi series DESCRIPTIONS” for the motor specification detail.
図提
番出

Table 1) Standard parameter table for new added models
Motor Model LiS9000 LiS11000 αiS2000
LiS 4500B2/4
C2/2HV C2/4 2000HV
(200V)
(400V) (200V) spindle
Motor Specification 0446-B210 0454-B010 0455-B210 0091
Motor ID Number 366 383 390 476
INTST 2003 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 01000011
BITPA1 2005 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00001000
BITPA2 2007 00000000 00000000 00000000 00100000
2008 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000000
BITPA4 2011 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00100000
BITP12 2210 00000000 00000000 00000000 00000000
2211 00001000 00001000 00001000 10011110
BITP35 2300 10000000 10000000 10000000 00000000
2301 00000000 00000000 00000000 11000000
PK1 2040 4394 1453 3736 643
PK2 2041 -21486 -13899 -18246 -3600
PK3 2042 -2689 -1321 -2693 -1358
PK1V 2043 10 8 9 502
PK2V 2044 -131 -108 -121 -4500
PK3V 2045 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235
POA1 2047 -8705 -10496 -9409 843
BLCMP 2048 0 0 0 0
DPFMX 2049 0 0 0 0
POK1 2050 956 956 956 956
POK2 2051 510 510 510 510
RESERV 2052 0 0 0 2400
PPMAX 2053 21 21 21 21
PDDP 2054 1894 1894 1894 3787
PHYST 2055 319 319 319 319
EMFCMP 2056 0 0 0 0
PVPA 2057 0 0 0 -3363
PALPH 2058 0 0 0 -3200
PPBAS 2059 0 0 0 0
TQLIM 2060 5462 6372 6877 5097
EMFLMT 2061 120 120 120 0
POVC1 2062 32707 32729 32729 32309
POVC2 2063 768 489 492 5734
TGALMLV 2064 4 4 4 4
POVCLMT 2065 1214 1112 1311 27346
PK2VAUX 2066 0 0 0 0
FILTER 2067 0 0 0 0
FALPH 2068 0 0 0 0
VFFLT 2069 0 0 0 0
ERBLM 2070 0 0 0 0
PBLCT 2071 0 0 0 0
SFCCML 2072 0 0 0 0
PSPTL 2073 0 0 0 0
AALPH 2074 0 0 0 12288
OSCTPL 2077 0 0 0 0
PDPCH 2078 0 0 0 0
PDPCL 2079 0 0 0 0
DPFEX 2080 0 0 0 0
DPFZW 2081 0 0 0 0
BLENDL 2082 0 0 0 0
MOFCTL 2083 0 0 0 0
RTCURR 2086 810 776 842 2893
TDPLD 2087 0 0 0 0
MCNFB 2088 0 0 0 0
BLBSL 2089 0 0 0 0
ROBSTL 2090 0 0 0 2800
ACCSPL 2091 0 0 0 0
ADFF1 2092 0 0 0 0
VMPK3V 2093 0 0 0 0
BLCMP2 2094 0 0 0 0
AHDRTL 2095 0 0 0 0
RADUSL 2096 0 0 0 0
SMCNT 2097 0 0 0 0
DEPVPL 2098 0 0 0 0
ONEPSL 2099 400 400 400 400
INPA1 2100 0 0 0 0
INPA2 2101 0 0 0 0
DBLIM 2102 0 0 0 0
ABVOF 2103 0 0 0 0
ABTSH 2104 0 0 0 0
TRQCST 2105 1005 2111 2348 5957
LP24PA 2106 0 0 0 0
VLGOVR 2107 0 0 0 0
RESERV 2108 0 0 0 0
BELLTC 2109 0 0 0 0
MGSTCM 2110 0 0 0 784
DETQLM 2111 0 0 0 2720
AMRDML 2112 0 0 0 0
NFILT 2113 0 0 0 0
NINTCT 2127 0 0 0 3449
MFWKCE 2128 0 0 0 3000
MFWKBL 2129 0 0 0 1291
LP2GP 2130 0 0 0 0
LP4GP 2131 0 0 0 0
LP6GP 2132 0 0 0 0
PHDLY1 2133 0 0 0 2060
PHDLY2 2134 0 0 0 12820
DGCSMM 2159 0 0 0 0
TRQCUP 2160 0 0 0 0
OVCSTP 2161 0 0 0 140
POVC21 2162 0 0 0 32745
POVC22 2163 0 0 0 292
POVCLMT2 2164 0 0 0 13952
MAXCRT 2165 165 85 365 365
ACCBSLM 2304 0 0 0 2720
ACDCEND 2305 0 0 0 4112
DCIDBS 2310 0 0 0 1236
図提
番出

Improving the Semi-Full Error Observation Function

PARAMETER MANUAL

Correct, Del Date
Basic Function 1. Improving the Semi-Full Error Observation Function Correct 2011.03
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
DRAW. No. CUST.

01 11.03.02 Kameta Newly designed B-65270EN/07-035
SHEET
(1) Outline
This function monitors the difference in detection position between built-in detector and separate detector. If the
difference between the Pulsecoder and the separate detector is greater than or equal to the value specified by a
parameter, servo alarm "EXCESS ERROR (SEMI-FULL)" is issued.
It is useful for the check of normal operation of separate detector, and the monitoring of "slip" between motor and
machine.
(2) Notice
For a full-closed system, it is recommended to use this function.
With Series 30i, 31i, 32i, 35i-MODEL B, when using the analog input separate detector interface unit, the semi-full
error observation function becomes effective automatically. If the semi-full error level (No.2118) and the conversion
coefficients (No.2078, No.2079) are not setting, an illegal servo parameter setting alarm (detail number 1183) is
issued. Please set these parameters in this case.
However, since the semi-full error observation function cannot be validated in the following systems, please disable
the function by No.2565#0=1.
- When the gear reduction ratio between motor and position detector changes a lot.
- When "slip" between a motor and a detector by belt etc. happens.
In order to calculate the feedback for semi-closed, it is necessary to set the conversion coefficients. Please set up
parameters by referring to Section 4.5.8, "Cautions on setting of the dual position feedback conversion coefficient"
in servo parameter manual (B-65270).
(3) Available Servo Software Series and Edition

- The semi-full error observation function
(Series 30i-B, 31i-B, 32i-B, 35i-B)
Series 90G0/01.0 and subsequent editions
(Series 0i-D)
Series 90C5/A(01) and subsequent editions
(Series 15i-B, 16i-B, 18i-B, 21i-B, Power Mate i)
- Setting parameter in units of μm. New

Series 90E0/31.0 and subsequent editions
TITLE
DRAW. No. CUST.

SHEET
- The function bit to disable this function for analog input separate detector interface unit (No.2565#0). New
(4) Parameters
When using Semi-full error observation function, set the following parameters:
No.2118 Semi-full error level

[Setting value] Semi-full error level (µm) / detection unit (µm),
or Semi-full error level (µm)
[Unit of data] Detection unit, or µm (See No.2420#7)
If the difference between the Pulsecoder and the separate detector is greater than or equal to the
value specified by the parameter, servo alarm is issued by judging it the abnormal state. Set a value
two to three times as large as the backlash. When 0 is set, detection is disabled.
#7 #6 #5 #4 #3 #2 #1 #0
No.2420 SFUMSET
SFUMSET(#7) Unit of data in parameter of Semi-full error level (No.2118) is:
New 0: Detection unit
1: 1µm
#7 #6 #5 #4 #3 #2 #1 #0
No.2565 SFEROFF
SFEROFF(#0) On the machine of the full-closed mode which uses analog input separate detector interface unit,
New the semi-full error observation function is:
0: Valid
1: Invalid
If the analog input separate detector interface unit is used in full-closed axis, Semi-full error
observation function is automatically enabled. As a result, if you don’t set Semi-full error level
(No.2118), the illegal servo parameter setting alarm (detail number 1183) is issued.
In case that Semi-full error observation function can’t be applied to the machine, please set this
function bit to disable Semi-full error observation function.
No.2078 Conversion coefficient (numerator)
No.2079 Conversion coefficient (denominator)

[Setting value] Reduce the following fraction and use the resulting irreducible fraction.
Number of position feedback pulses

per motor revolution
Conversion ⎛ Numerator ⎞ (Value multiplied by the feed gear)
⎜ ⎟　 =
coefficient ⎝ Denominato r ⎠ 1 million
(Example)
When the αi Pulsecoder is used with a tool travel of 10 mm/motor revolution (1 µm/pulse)
Conversion ⎛ Numerator ⎞ 10 × 1000 1
⎜ ⎟ = =
coefficient ⎝ Denominato r ⎠ 1,000,000 100
TITLE
DRAW. No. CUST.

SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i/ 35i-B(90G0)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
2. Improving the Semi-Full Error Observation Function Add 2011.02
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
称 for Series 30i/ 31i/ 32i/ 35i -B (90G0)
図提
番出

Notice of the Update of Digital Servo Software for Series 30i/ 31i / 32i /35i -B (90G0)
1. Update Edition
90G0 07.0 Series 30i/ 31i/ 32i/ 35i -B
- Improving the Semi-Full Error Observation Function

This function monitors the "difference of detection position between motor built-in detector and
separate detector". It is effective to check normal operation of separate detector, and the monitoring of
"slip" between motor and machine. The following improvements are added.
- If the analog input separate detector interface unit is used in full-closed axis, Semi-full error
observation function is automatically enabled. As a result, if you don’t set Semi-full error level
(No.2118), the illegal servo parameter setting alarm (detail number 1183) is issued.
- The unit of data in parameter of Semi-full error level (No.2118) can be chosen to “μm” unit.
Please refer to the Technical report B-65270EN/07-035 “Improving the Semi-Full Error Observation
Function)” for the details.
3. Attached
図提
番出

LiS 4500B2/4 0446-B210 366

LiS9000C2/2HV 0454-B010 383
LiS 11000C2/4 0455-B210 390

αiS2000/2000
0091 476
for Spindle use
図提
番出

Motor Model LiS9000 LiS11000 αiS2000
LiS 4500B2/4
C2/2HV C2/4 2000HV
(200V)
(400V) (200V) spindle
Motor Specification 0446-B210 0454-B010 0455-B210 0091
Motor ID Number 366 383 390 476
Symbol FS30i,31i,32i,35i
INTST 2003 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 01000011
BITPA1 2005 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00001000
BITPA2 2007 00000000 00000000 00000000 00100000
2008 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000000
BITPA4 2011 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00100000
BITP12 2210 00000000 00000000 00000000 00000000
2211 00001000 00001000 00001000 10011110
BITP35 2300 10000000 10000000 10000000 00000000
2301 00000000 00000000 00000000 11000000
PK1 2040 4394 1453 3736 643
PK2 2041 -21486 -13899 -18246 -3600
PK3 2042 -2689 -1321 -2693 -1358
PK1V 2043 10 8 9 502
PK2V 2044 -131 -108 -121 -4500
PK3V 2045 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235
POA1 2047 -8705 -10496 -9409 843
BLCMP 2048 0 0 0 0
DPFMX 2049 0 0 0 0
POK1 2050 956 956 956 956
POK2 2051 510 510 510 510
RESERV 2052 0 0 0 2400
PPMAX 2053 21 21 21 21
PDDP 2054 1894 1894 1894 3787
PHYST 2055 319 319 319 319
EMFCMP 2056 0 0 0 0
PVPA 2057 0 0 0 -3363
PALPH 2058 0 0 0 -3200
PPBAS 2059 0 0 0 0
TQLIM 2060 5462 6372 6877 5097
EMFLMT 2061 120 120 120 0
POVC1 2062 32707 32729 32729 32309
POVC2 2063 768 489 492 5734
TGALMLV 2064 4 4 4 4
POVCLMT 2065 1214 1112 1311 27346
PK2VAUX 2066 0 0 0 0
FILTER 2067 0 0 0 0
FALPH 2068 0 0 0 0
VFFLT 2069 0 0 0 0
ERBLM 2070 0 0 0 0
PBLCT 2071 0 0 0 0
SFCCML 2072 0 0 0 0
PSPTL 2073 0 0 0 0
AALPH 2074 0 0 0 12288
OSCTPL 2077 0 0 0 0
PDPCH 2078 0 0 0 0
PDPCL 2079 0 0 0 0
DPFEX 2080 0 0 0 0
DPFZW 2081 0 0 0 0
BLENDL 2082 0 0 0 0
MOFCTL 2083 0 0 0 0
RTCURR 2086 810 776 842 2893
TDPLD 2087 0 0 0 0
MCNFB 2088 0 0 0 0
BLBSL 2089 0 0 0 0
ROBSTL 2090 0 0 0 2800
ACCSPL 2091 0 0 0 0
ADFF1 2092 0 0 0 0
VMPK3V 2093 0 0 0 0
BLCMP2 2094 0 0 0 0
AHDRTL 2095 0 0 0 0
RADUSL 2096 0 0 0 0
SMCNT 2097 0 0 0 0
DEPVPL 2098 0 0 0 0
ONEPSL 2099 400 400 400 400
INPA1 2100 0 0 0 0
INPA2 2101 0 0 0 0
DBLIM 2102 0 0 0 0
ABVOF 2103 0 0 0 0
ABTSH 2104 0 0 0 0
TRQCST 2105 1005 2111 2348 5957
LP24PA 2106 0 0 0 0
VLGOVR 2107 0 0 0 0
RESERV 2108 0 0 0 0
BELLTC 2109 0 0 0 0
MGSTCM 2110 0 0 0 784
DETQLM 2111 0 0 0 2720
AMRDML 2112 0 0 0 0
NFILT 2113 0 0 0 0
NINTCT 2127 0 0 0 3449
MFWKCE 2128 0 0 0 3000
MFWKBL 2129 0 0 0 1291
LP2GP 2130 0 0 0 0
LP4GP 2131 0 0 0 0
LP6GP 2132 0 0 0 0
PHDLY1 2133 0 0 0 2060
PHDLY2 2134 0 0 0 12820
DGCSMM 2159 0 0 0 0
TRQCUP 2160 0 0 0 0
OVCSTP 2161 0 0 0 140
POVC21 2162 0 0 0 32745
POVC22 2163 0 0 0 292
POVCLMT2 2164 0 0 0 13952
MAXCRT 2165 165 85 365 365
ACCBSLM 2304 0 0 0 2720
ACDCEND 2305 0 0 0 4112
DCIDBS 2310 0 0 0 1236
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate-D(90C5)
1. Update Edition
90C5 05.0 Series 0i-D/ 0i Mate-D
-Inertia Estimation Function
This function estimates the inertia of a servo motor axis.
Please refer to the Technical report TMS11/021 “ Operation Manual for Inertia Estimation
Function” for the details.
称 for Series 0i-D / 0i Mate-D (90C5)
図提
01 11.04.07 Tang Newly designed 番
B-65270-037EN
出

Speed Arrival Signal and Zero-Speed Detecting Signal

Parameter manual

Correct, Del Date
Basic Function - Speed Arrival Signal and Zero-Speed Detecting Add 2012.08
Signal has been supported by 0i-D.
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Speed Arrival Signal and Zero-Speed
Detecting Signal
DRAW. No. CUST.
B-65270EN/07-038/02
02 12.08.24 Tang Page 2,3 are changed
Speed Arrival Signal and Zero-Speed Detecting Signal
(1) Outline
Speed arrival signal (SVSAR) and Zero-speed detecting signal (SVSST) have been supported.
These signals are effective in using Spindle control by servo motor. Please refer to CNC connection
manual (function) for the detail of Spindle control with servo motor.

-Speed Arrival Signal and Zero-Speed Detecting Signal has been adped from
90G0 series version 03.0 and subsequent editions
90D0 series version T(20) and subsequent editions
90E0 series version T(20) and subsequent editions
90E1 series version 0.10 and subsequent editions
90C8 series version 4.0 and subsequent editions (2)
- Detecting Speed Arrival Signal at low-speed mode

90C8 series version 4.0 and subsequent editions (2)
(3) Available System software

Please use the following system software in using Speed arrival signal and Zero-speed detecting signal.
-FS 30i –A Series CNC
For the following sysytem software 31.0 or subsequent editions is needed

FS30i -A G003, G013, G023, G033
G00C, G01C, G02C, G03C
FS31i -A5 G123, G133
G12C, G13C
FS31i -A G103, G113
FS32i -A G203
For the following sysytem software 48.0 or subsequent editions is needed

FS30i -A G002, G012, G022, G032
G00B, G01B, G02B, G03B
FS31i -A5 G121, G131
G12B, G13B
FS31i -A G101, G111
FS32i -A G201
For the following sysytem software, It has been supported from First Version.
FS30i -A G004, G014, G024, G034
FS31i -A5 G124, G134 (2)
FS31i -A G104, G114

FS32i -A G204
TITLE
Detecting Signal
DRAW. No. CUST.
02 12.08.24 Tang (2) are changed or added.

B-65270EN/07-038/02
-FS 30i –B Series CNC
For the following sysytem software, It has been supported from First Version.
FS30i -B G301, G311, G321, G331, G33T
FS31i -B5 G421, G431
FS31i -B G401, G411
FS32i -B G501, G511
(2)
-FS 0i –D Series CNC
For the following sysytem software 25.0 or subsequent editions is needed.
FS S0i –TD D6F1

FS0i -MD D4F1
FS0i Mate-TD D7F1
TITLE
Detecting Signal
DRAW. No. CUST.
02 12.08.24 Tang (2) are changed or added.

B-65270EN/07-038/02
(4) Parameters
2482 Detection level of speed arrival (SVSAR)

[setting unit] 0.1%
[default value] 0（Setting value “0” means “15”% internally.）
Detection level of speed arrival means the ratio to commanded speed. When the
subtraction of actual speed from commanded becomes lower than (commanded
speed) × (ratio), actual speed is judged as reach to the commanded speed, and
Speed arrival signal, SVSARn becomes “1”.
Commanded speed for the

judgment of speed arrival
speed
The range that speed arrival signal (SAR) is “1”
(speed command)×(1±SVSAR/1000)
Actual speed
Speed command for speed control

(acceleration or deceleration is included)
time
SAR=0 SAR=1
Offset speed is set up to prevent that detection level becomes too small at low rotation mode. By setting the Offset
speed, Speed arrival signal also can be detected at low rotation mode. Moreover, Hysteresis speed is set up for the
prevention with speed arrive singnal floppy. Offset speed and Hysteresis speed can be changed by setting up the
following bit parameters.
#7 #6 #5 #4 #3 #2 #1 #0
2422 SVSAR1 SVSAR2
SVSAR1 Detection level of speed arrival coefficient 1
SVSAR2 Detection level of speed arrival coefficient 2
Table about offset and hysteresis

SVSAR1 SVSAR2 Offset speed Hysteresis speed Refer
0 0 50/min 20/min Recommend
(for αi, βi series motor)
0 1 10/min 5/min
1 0 5/min 2/min Recommend
(for DiS series motor)
1 1 2/min 1/min
The next page shows the relation among velocity command (VCMD), actul speed and speed arrival signal.
TITLE
Detecting Signal
DRAW. No. CUST.
B-65270EN/07-038/02
Relationship ammong VCMD , Actual Speed and Speed Arrival Singal
Velocity command(VCMD) actual speed
VCMDx(1-No2482 /1000)
Offset speed (/min)

Detection Level
(1) Offset speed /min
0 (2) VCMDxNo2482/1000+ Offset speed /min
Speed arrival signal 1 (3) VCMDxNo2482/1000+ Offset speed /min
+ Hysteresis speed /min
(4) Offset speed /min
deviation of actual speed
SAR detection lever

(2) (3)
(1) (4)
Hysteresis value is preparied to prevent floppy of spindle arrival singal switching.
SAR=1
SAR=0
|deviation of actual speed|=|VCMD-actual speed|
Hysteresis speed
15%of motor VCMD （standard）

＋Offset speed min-1 （preventing floppy at low rotation mode）
2483 Detection level of speed zero (SVSST)

Detection level of zero speed means the revolution speed(1/min) that is used to judge
stopping. When the actual speed becomes lower than detection level of zero speed,
motor is judged to be stopped, and Zero-speed detecting signal, SVSSTn becomes
“1”.
speed
commanded speed for the
judgment of zero speed
actual speed
the range that Zero-speed
detecting signal (SVSST) is “1”
±SVSST[rpm]
time
SVSST=0 SVSST=1
TITLE
Detecting Signal
DRAW. No. CUST.
B-65270EN/07-038/02
(5) PMC Signals
Speed arrival signal SVSAR1~SVSAR8<Fn377>

[Function] This signal shows that the actual speed of the servo motor arrives at the preset
range arround the commanded speed at spindle control by servo motor.
[Operation] - SVSARn becomes “1” when the actual speed arrives at the commanded speed.
- SVSARn becomes “0” when the actual speed has not arrived at the
commanded speed.
Zero-speed detecting signal SVSST1~SVSST8<Fn376>

[Function] This signal shows that the actual speed of the servo motor that is controled by
spindle control by servo motor comes into detection level of zero speed.
[Operation] - SVSSTn becomes “1” when the actual speed is zero.
- SVSSTn becomes “0” when the actual speed is not zero.
signal address
#7 #6 #5 #4 #3 #2 #1 #0
Fn376 SVSST8 SVSST7 SVSST6 SVSST5 SVSST4 SVSST3 SVSST2 SVSST1
#7 #6 #5 #4 #3 #2 #1 #0
Fn377 SVSAR8 SVSAR7 SVSAR6 SVSAR5 SVSAR4 SVSAR3 SVSAR2 SVSAR1
- SVSARn is “0” at emergency stop. So, aftter emergency stop, SVSARn becomes “0” even if the
motor is rotating and in the range of speed arrival. Also in case of some alarms and rotating with
dynamic brake, SVSARn becomes “0”.
- In the case of servo off, SVSARn will be “0”.
- As servo software always watches zero speed condition, SVSSTn will be changed according to
the real motor speed. (The signal condition will not relate to emergency stop, alarm, and servo
off.)
- But when the motor feedback alarm (such as communication alarm by disconnection of
encoder) occurs, the feedback data will be unstable. Is such case, there is a possibility tha the
output of the signal might be wrong.
- You can’t use these two signals for safety function, which protects workers from danger by the
machine.
TITLE
Detecting Signal
DRAW. No. CUST.
B-65270EN/07-038/02

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Basic Function - Changes of Standard Parameter Table Add 2011.06
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
名 Notice of the Update of Digital Servo Software for
称 Series 15i, 16i, 18i, 21i, PMi -D, PMi -H ( 90BP)
図提
番出

1. Update Edition
90BP 08
3. Attached
図提
番出

LiS 4500B2/4 0446-B210 366

LiS9000C2/2HV 0454-B010 383
LiS 11000C2/4 0455-B210 390
DiS 400/250(200V) 0485-B20x 419

DiS 400/250(400V) 0485-B20x 420
DiS 800/250(200V) 0485-B40x 433
DiS 800/250(400V) 0485-B40x 434
図提
番出

LiS4500 LiS9000 LiS11000 DiS400 DiS400 DiS800/ DiS800/
Motor model B2/4 C2/2HV C2/4 /250 /250 250 250
(200V) (400V) (200V) (200V) (400V) (200V) (400V)
Motor specification 0446-B210 0454-B010 0455-B210 0485-B20x 0485-B20x 0485-B40x 0485-B40x
Motor ID number 366 383 390 419 420 433 434
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00000000 00000000 00000000 00001000 00001000
2014 00000000 00000000 00000000 00000000 00000000 00001000 00001000
BITP12 2210 00000000 00000000 00000000 00000100 00000100 00000100 00000100
2211 00001000 00001000 00001000 00001000 00001000 00000000 00000000
BITP35 2300 10000000 10000000 10000000 10000110 10000110 10000100 10000100
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 4394 1453 3736 494 494 738 496
PK2 2041 -21486 -13899 -18246 -1949 -1352 -2500 -1588
PK3 2042 -2689 -1321 -2693 -2943 -2943 -2996 -2996
PK1V 2043 10 8 9 415 415 386 343
PK2V 2044 -131 -108 -121 -3713 -3713 -3461 -3076
PK3V 2045 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 -8705 -10496 -9409 2271 2271 2437 2742
BLCMP 2048 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0
PPMAX 2053 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0
PVPA 2057 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0
TQLIM 2060 5462 6372 6877 7282 7282 5648 5020
EMFLMT 2061 120 120 120 0 0 0 0
POVC1 2062 32707 32729 32729 32743 32743 32713 32713
POVC2 2063 768 489 492 308 308 690 690
TGALMLV 2064 4 4 4 4 4 4 4
POVCLMT 2065 1214 1112 1311 903 903 1200 948
PK2VAUX 2066 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0
AALPH 2074 0 0 0 20480 20480 0 0
OSCTPL 2077 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0
RTCURR 2086 810 776 842 753 753 868 772
TDPLD 2087 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0
TRQCST 2105 1005 2111 2348 8080 8080 16519 18584
LP24PA 2106 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0
MGSTCM 2110 0 0 0 1281 1281 0 0
DETQLM 2111 0 0 0 1535 0 0 0
AMRDML 2112 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0
MFWKCE 2128 0 0 0 16776 0 0 0
MFWKBL 2129 0 0 0 14 0 0 0
LP2GP 2130 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 120 120 0 0
POVC21 2162 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0
MAXCRT 2165 165 85 365 85 85 165 185
ACCBSLM 2304 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate -D(90C8, 90E8)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
称 for Series 0i-D / 0i Mate-D ( 90C8,90E8)
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate-D(90C8, 90E8)
1. Update Edition
90E8 02 Series 0i-D ( Series 0i-TD, 2Path System )
3. Attached
図提
番出

LiS 4500B2/4 0446-B210 366

LiS9000C2/2HV 0454-B010 383
LiS 11000C2/4 0455-B210 390
DiS 400/250(200V) 0485-B20x 419

DiS 400/250(400V) 0485-B20x 420
DiS 800/250(200V) 0485-B40x 433
DiS 800/250(400V) 0485-B40x 434
αiS2000/2000
0091 476
for Spindle use
図提
番出

ﾓｰﾀﾓﾃﾞﾙ LiS4500 LiS9000 LiS11000 DiS400 DiS400 DiS400 DiS400 αiS2000
B2/4 C2/2HV C2/4 /250 /250 /250 /250 2000HV
(200V) (400V) (200V) (200V) (400V) (200V) (400V) spindle
ﾓｰﾀ図番 0446-B210 0454-B010 0455-B210 0485-B20x 0485-B20x 0485-B20x 0485-B20x 0091
ﾓｰﾀ型式 366 383 390 419 420 419 420 476
シンボル FS0i-D
INTST 2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
BITPA1 2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00001000
BITPA2 2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA3 2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000000 00000000 00000000 00000000 00000000
BITPA4 2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
BITPA5 2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
BITP12 2210 00000000 00000000 00000000 00000100 00000100 00000100 00000100 00000000
2211 00001000 00001000 00001000 00001000 00001000 00001000 00001000 10011110
BITP35 2300 10000000 10000000 10000000 10000110 10000110 10000110 10000110 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 11000000
PK1 2040 4394 1453 3736 494 494 494 494 643
PK2 2041 -21486 -13899 -18246 -1949 -1352 -1949 -1352 -3600
PK3 2042 -2689 -1321 -2693 -2943 -2943 -2943 -2943 -1358
PK1V 2043 10 8 9 415 415 415 415 502
PK2V 2044 -131 -108 -121 -3713 -3713 -3713 -3713 -4500
PK3V 2045 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 -8705 -10496 -9409 2271 2271 2271 2271 843
BLCMP 2048 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 0 0 0 2400
PPMAX 2053 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 3787
PHYST 2055 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0
PVPA 2057 0 0 0 0 0 0 0 -3363
PALPH 2058 0 0 0 0 0 0 0 -3200
PPBAS 2059 0 0 0 0 0 0 0 0
TQLIM 2060 5462 6372 6877 7282 7282 7282 7282 5097
EMFLMT 2061 120 120 120 0 0 0 0 0
POVC1 2062 32707 32729 32729 32743 32743 32743 32743 32309
POVC2 2063 768 489 492 308 308 308 308 5734
TGALMLV 2064 4 4 4 4 4 4 4 4
POVCLMT 2065 1214 1112 1311 903 903 903 903 27346
PK2VAUX 2066 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0
AALPH 2074 0 0 0 20480 20480 20480 20480 12288
OSCTPL 2077 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0
RTCURR 2086 810 776 842 753 753 753 753 2893
TDPLD 2087 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 2800
ACCSPL 2091 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0
TRQCST 2105 1005 2111 2348 8080 8080 8080 8080 5957
LP24PA 2106 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0
MGSTCM 2110 0 0 0 1281 1281 1281 1281 784
DETQLM 2111 0 0 0 1535 0 1535 0 2720
AMRDML 2112 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 3449
MFWKCE 2128 0 0 0 16776 0 16776 0 3000
MFWKBL 2129 0 0 0 14 0 14 0 1291
LP2GP 2130 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 2060
PHDLY2 2134 0 0 0 0 0 0 0 12820
DGCSMM 2159 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 120 120 120 120 140
POVC21 2162 0 0 0 0 0 0 0 32745
POVC22 2163 0 0 0 0 0 0 0 292
POVCLMT2 2164 0 0 0 0 0 0 0 13952
MAXCRT 2165 165 85 365 85 85 85 85 365
ACCBSLM 2304 0 0 0 0 0 0 0 2720
ACDCEND 2305 0 0 0 0 0 0 0 4112
DCIDBS 2310 0 0 0 0 0 0 0 1236
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate -D(90C5)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
称 for Series 0i-D / 0i Mate-D ( 90C5)
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate-D(90C5)
1. Update Edition
3. Attached
図提
番出

(1) αiS series

- 3000/min models standard parameters have been added.
Motor Model Motor Specification Motor ID No. Refer
αiF 30/3000 0255 304 -
αiF 40/3000HV 0259 309 400V driving
αiF 40/3000HV Fan 0259 479 400V driving
*Please refer to Table1 about the standard parameters.
-The following motor’s standard parmeter has been modified for stability.
Motor Model Motor Specification Motor ID No. Amplifer Power Supply
200V input： 200V input：

αiF 22/3000 0247 297
A06B-6117-Hxxx A06B-6140-Hxxx
*Please refer to Table 1 about the standard parameters.
- Dead band parameter (N2004#6) of following motors hasbeen changed to 0.

αiS 50/3000HV Fan 0276 326
αiS 50/3000HV 0276 327
αiS 60/3000HV Fan 0279 329
(2) βiS series

- 2000/min models standard parameter have been added.
βiS 30/2000 0087 472 -
βiS 30/2000HV 0088 473 400V driving
βiS 40/2000 0089 474 -
βiS 40/2000HV 0090 475 400V driving
図提
番出

- Standard parameters of βiS12/3000, βiS22/2000 driven by 80A ampplifer have been added.
Motor Model Motor Specification Motor ID No. Driven Amplifer
βiS 12/3000 272（exist） 40A

0078
477 80A
βiS 22/2000 274(exist) 40A
0085
478 80A

-
(3) LiS series
-Standard parameters for new models have been added.
LiS 4500B2/4 0446-B210 366 -
LiS 9000C2/2HV 0454-B010 383 400V driving
LiS 11000C2/4 0455-B210 390 -
(4) DiS series

-Standard parameters for new models have been added.
- Following models are driven by 200V ampilifer.
DiS15/1000 0492-B100 551
DiS 60/400 0493-B200 553
DiS 70/300 0494-B100 555
DiS 150/300 0494-B300 557
DiS 200/300 0494-B400 559
DiS 250/250 0495-B200 561

DiS 400/250 0485-B20x 419
DiS 500/250 0495-B400 563

DiS 800/250 0485-B40x 433
DiS1000/200 0496-B300 565
DiS1500/100 0497-B300 567
DiS 2000/100 0497-B400 569
DiS 2000/150 0497-B490 571

* Please refer to Table 3,4,5 about the standard parameters.
図提
番出

- Following models are driven by 400V ampilifer.
DiS15/1000 0492-B100 552
DiS 60/400 0493-B200 554
DiS 70/300 0494-B100 556
DiS 150/300 0494-B300 558
DiS 200/300 0494-B400 560
DiS 250/250 0495-B200 562

DiS 400/250 0485-B20x 420
DiS 500/250 0495-B400 564

DiS 800/250 0485-B40x 434
DiS 1000/200 0496-B300 566
DiS 1500/100 0497-B300 568
DiS 2000/100 0497-B400 570
DiS 2000/150 0497-B490 572
DiS 5000/50 0488-B400 573

*Please refer to Table3,4,5 about the standard parameters.
図提
番出

Table 1) Standard parameter table for changed and new added models
βiS22
αiF22 αiF30 αiF40 βiS30 βiS30 βiS40 βiS40 βiS12 αiF40
Motor Model 2000
3000 3000HV 3000HV 2000 2000HV 2000 2000HV 3000(80A) 3000HV Fan
(80A)
Motor ID Number 297 304 309 472 473 474 475 477 478 479
Symbol FS0i,0i Mate
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00100000 00100000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000010 00000010 00000010 00000010 00001110 00001110 00000000
2014 00000000 00000000 00000000 00000010 00000010 00000010 00000010 00001110 00001110 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00000000 00001010 00011010 00001010 00001010 00001010 00001010 00001110 00001110 00011010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1750 785 1441 1650 1650 1624 1624 804 2368 1441
PK2 2041 -6000 -4179 -7513 -6565 -6565 -7197 -7197 -4434 -13600 -7513
PK3 2042 -1345 -1347 -1350 -2681 -2681 -1341 -1341 -1304 -1331 -1350
PK1V 2043 198 225 188 214 214 208 208 85 121 188
PK2V 2044 -1775 -2016 -1684 -1912 -1912 -1870 -1870 -765 -1086 -1684
PK3V 2045 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 2137 -1882 2253 3971 3971 4057 4057 9920 6992 2253
BLCMP 2048 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510
RESERV 2052 3600 3700 3600 2800 2800 2600 2600 4200 2800 3600
PPMAX 2053 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 -5130 0
PVPA 2057 -5136 -7696 -5137 -4647 -4647 -3375 -3375 -5130 -3598 -5137
PALPH 2058 -2800 -2458 -2027 -3115 -3115 -3862 -3862 -1750 -1500 -2027
PPBAS 2059 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 7282 6554 6554 6554 6554 3641 3641 7282
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32520 32501 32501 32413 32413 32413 32413 31932 31744 32501
POVC2 2063 3101 3332 3332 4431 4431 4431 4431 10454 12801 3332
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 9224 9912 9912 13201 13201 13201 13201 5230 6422 9912
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0
AALPH 2074 12288 12288 8192 8192 8192 8192 8192 0 0 8192
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 2131 2259 1876 2154 2154 2154 2154 1181 1309 2607
TDPLD 2087 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 15000 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 929 2215 1869 1127 1127 1503 1503 836 1384 1869
LP24PA 2106 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1291 1291 1044 1546 1546 263 263 812 1280 1044
DETQLM 2111 0 6974 4241 4255 4255 3065 3065 7930 2866 4241
AMRDML 2112 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 3272 3354 6538 2095 2095 2712 2712 1194 2459 6538
MFWKCE 2128 4500 3000 6147 3066 3066 3354 3354 6000 10000 6147
MFWKBL 2129 1301 2833 1809 1548 1548 1038 1038 2056 562 1809
LP2GP 2130 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 5150 3594 4110 4110 2567 2567 5138 3350 3594
PHDLY2 2134 0 8990 6414 12814 12814 8967 8967 4382 4371 6414
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0 0 0
POVC21 2162 32765 32763 32762 32765 32765 32765 32765 32766 32766 32763
POVC22 2163 40 58 78 34 34 36 36 31 31 58
POVCLMT2 2164 7229 9912 8288 7387 7387 7713 7713 2752 3379 9912
MAXCRT 2165 85 85 85 85 45 85 45 85 85 85
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 36 0 0 0 0 0 0 36
DCIDBS 2310 1817 0 0 0 0 0 0 0 0 0
STJG 2302 0 0 0 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0 0 0 0
図提
番出

LiS4500 LiS9000 LiS11000 LiS10000 LiS17000
Motor Model B2/4 C2/2HV C2/4 C3/2HV C3/2HV
(200V) (400V) (200V) (400V) (400V)
Motor
0446-B210 0454-B010 0455-B210 0457-B010 0459-B010
specification
Motor ID
366 383 390 395 399
Number
Symbol FS0i,0i Mate
2003 00001000 00001000 00001000 00001000 00000000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000100 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000100 00000000
2014 00000000 00000000 00000000 00000100 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00001000 00001000 00001000 00001000 00000000
2300 10000000 10000000 10000000 10000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 4394 1453 3736 3010 709
PK2 2041 -21486 -13899 -18246 -6519 -3688
PK3 2042 -2689 -1321 -2693 -2695 -1330
PK1V 2043 10 8 9 10 7
PK2V 2044 -131 -108 -121 -129 -99
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 -8705 -10496 -9409 -8849 -11497
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
OSPLV 2052 0 0 0 0 0
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 -12032
PVPA 2057 0 0 0 0 0
PALPH 2058 0 0 0 0 0
PPBAS 2059 0 0 0 0 0
TQLIM 2060 5462 6372 6877 7282 5259
EMFLMT 2061 120 120 120 120 120
POVC1 2062 32707 32729 32729 32722 32711
POVC2 2063 768 489 492 576 709
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 1214 1112 1311 1707 981
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 0 0 0 -4096 -24576
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 810 776 842 961 729
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 1005 2111 2348 2043 4197
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 0 0 0 0 0
DETQLM 2111 0 0 0 0 0
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 0 0 0 0 0
MFWKCE 2128 0 0 0 0 0
MFWKBL 2129 0 0 0 0 0
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 0 0 0 0 0
POVC22 2163 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0
MAXCRT 2165 165 85 365 85 185
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0
STJG 2302 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0
図提
番出

DiS400 DiS400 DiS800 DiS800 DiS15 DiS15 DiS60 DiS60 DiS70 DiS70 DiS150
Motor Model /250 /250 /250 /250 /1000 /1000 /400 /400 /300 /300 /300
(200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V)
Motor specification 0485-B20x 0485-B20x 0485-B40x 0485-B40x 0492-B100 0492-B100 0493-B200 0493-B200 0494-B100 0494-B100 0494-B300
Motor ID Number 419 420 433 434 551 552 553 554 555 556 557
Symbol FS0i,0i Mate
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000010 00000000 00000010
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
2014 00000000 00000000 00001000 00001000 00000000 00000000 00001000 00001000 00000110 00000110 00000110
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00000000 00000000 00011000 00001000 00001000 00001000 00001000 00001000 00001000
2300 10000110 10000110 10000100 10000100 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 494 494 738 496 309 154 538 269 296 148 379
PK2 2041 -1949 -1352 -2500 -1588 -1713 -857 -3794 -1897 -2764 -1382 -3215
PK3 2042 -2943 -2943 -2996 -2996 -3067 -3067 -3102 -3102 -3117 -3117 -3128
PK1V 2043 415 415 386 343 69 69 86 86 180 180 149
PK2V 2044 -3713 -3713 -3461 -3076 -618 -618 -772 -772 -1614 -1614 -1331
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 2271 2271 2437 2742 13637 13637 10929 10929 5224 5224 6336
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 0 0 0 0 720 1200 240 480 180 360 180
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0 0 0 0
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 7282 7282 5648 5020 7282 7282 5462 5462 6190 6190 6190
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32743 32743 32713 32713 32675 32675 32675 32675 32684 32684 32714
POVC2 2063 308 308 690 690 1160 1160 1160 1160 1056 1056 679
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 903 903 1200 948 3300 3300 1856 1856 2178 2178 1419
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 20480 20480 0 0 -20480 -20480 -32768 -32768 -24576 -24576 -20480
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 753 753 868 772 1440 1440 845 845 1005 1005 944
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 8080 8080 16519 18584 612 612 2865 2865 3521 3521 7830
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1281 1281 0 0 2305 2049 1793 1793 1793 1793 1793
DETQLM 2111 1535 0 0 0 8854 0 6174 0 5173 0 5173
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 16776 0 0 0 16000 0 4000 0 0 0 4000
MFWKBL 2129 14 0 0 0 277 0 6158 0 0 0 5134
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 120 120 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 165 185 25 25 45 45 45 45 85
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 72 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
STJG 2302 0 0 0 0 72 0 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0 0 0 0 0 0 0
図提
番出

Motor Model /300 /300 /300 /250 /250 /250 /250 /200 /200 /100 /100
(400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V) (200V) (400V)
Motor ID Number 558 559 560 561 562 563 564 565 566 567 568
Symbol FS0i,0i Mate
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000010 00000010 00000010 00000010 00000010 00000010 00001010 00000010 00001010 00001010
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
2014 00000110 00000110 00000110 00000000 00000000 00000000 00000100 00000000 00000100 00000000 00000100
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00011000 00011000 00001000 00001000 00001000 00001000 00011000 00001000 00011000 00001000
2300 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10010100 10010100 10000000 10000000
PK1 2040 189 451 226 294 158 321 181 434 244 490 276
PK2 2041 -1607 -3966 -1983 -2458 -1150 -2569 -1445 -2352 -1323 -3676 -2068
PK3 2042 -3128 -3135 -3135 -3129 -3129 -3138 -3138 -3173 -3173 -3176 -3176
PK1V 2043 149 141 141 334 334 297 264 558 496 760 676
PK2V 2044 -1331 -1261 -1261 -2996 -2996 -2664 -2368 -4997 -4442 -6812 -6055
PK3V 2045 0 0 0 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 6336 6686 6686 2815 2815 3165 3561 1688 1899 1238 1393
BLCMP 2048 0 0 0 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510 510 510 510
RESERV 2052 360 180 360 150 300 150 300 120 240 60 120
PPMAX 2053 21 21 21 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 -11264 0 -11264 0 -11264
PVPA 2057 0 0 0 0 0 0 0 0 0 0 0
PALPH 2058 0 0 0 0 0 0 0 0 0 0 0
PPBAS 2059 0 0 0 0 0 0 0 0 0 0 0
TQLIM 2060 6190 6190 6190 7282 7282 7282 6473 7282 6473 7282 6473
EMFLMT 2061 0 0 0 0 0 0 0 0 0 0 0
POVC1 2062 32714 32721 32721 32707 32707 32723 32723 32677 32677 32682 32682
POVC2 2063 679 590 590 761 761 567 567 1135 1135 1078 1078
TGALMLV 2064 4 4 4 4 4 4 4 4 4 4 4
POVCLMT 2065 1419 1237 1237 2196 2196 1646 1301 3231 2553 3076 2430
PK2VAUX 2066 0 0 0 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0 0 0 0
AALPH 2074 -20480 -4096 -4096 -4096 -8192 20480 20480 -20480 -20480 28672 28672
OSCTPL 2077 0 0 0 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0 0 0 0
RTCURR 2086 944 881 881 1175 1175 1062 944 1421 1266 1390 1235
TDPLD 2087 0 0 0 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 0 0 0 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0 0 0 0
TRQCST 2105 7830 11266 11266 10329 10329 20150 22669 3349 3768 5516 6206
LP24PA 2106 0 0 0 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0 0 0 0
MGSTCM 2110 1793 1793 1793 1793 1793 2049 2049 2049 2305 2049 2049
DETQLM 2111 0 2625 7710 3890 12900 3890 11311 2680 6229 1184 3212
AMRDML 2112 0 0 0 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0 0 0 0
NINTCT 2127 0 0 0 0 0 0 0 0 0 0 0
MFWKCE 2128 0 6000 0 7000 0 5000 0 10000 0 5000 0
MFWKBL 2129 0 2581 0 3861 0 3861 0 2588 0 1042 0
LP2GP 2130 0 0 0 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0 0 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0 0 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0 0 0 0
POVC21 2162 0 0 0 0 0 0 0 0 0 0 0
POVC22 2163 0 0 0 0 0 0 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0 0 0 0 0 0 0
MAXCRT 2165 85 85 85 85 85 165 185 165 185 165 185
ACCBSLM 2304 0 0 0 0 0 0 0 0 0 0 0
ACDCEND 2305 0 36 72 0 0 0 0 24 0 12 0
DCIDBS 2310 0 0 0 0 0 0 0 0 0 0 0
STJG 2302 0 0 0 0 0 0 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0 0 0 0 0 0 0
図提
番出

DiS2000 DiS2000 DiS2000 DiS2000 DiS5000
Motor Model /100 /100 /150 /150 /50
(200V) (400V) (200V) (400V) (400V)
Motor specification 0497-B400 0497-B400 0497-B490 0497-B490 0488-B400
Motor ID Number 569 570 571 572 573
Symbol FS0i,0i Mate
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00001010 00001010 00001010 00000010 00001010
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000100 00000100 00000100 00000000
2014 00000000 00000100 00000100 00000100 00000000
2210 00000100 00000100 00000100 00000100 00000100
2211 00011000 00011000 00001000 00001000 00011000
2300 10000110 10000110 10000110 10000110 10000110
2301 10000000 10000000 10000000 10000000 10010100
PK1 2040 637 358 448 224 417
PK2 2041 -5353 -3011 -3457 -1729 -3875
PK3 2042 -3177 -3177 -3177 -3177 -3181
PK1V 2043 689 612 620 620 1096
PK2V 2044 -6171 -5485 -5554 -5554 -9817
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 1367 1537 1518 1518 859
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 60 120 90 180 60
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 -11264 0 0 0
PVPA 2057 -1038 -2054 0 0 -527
PALPH 2058 -489 -430 0 0 -665
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 6473 6473 6473 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32709 32709 32707 32707 32731
POVC2 2063 740 740 763 763 459
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 2136 1688 1739 1739 1337
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 24576 24576 12288 12288 24576
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 1176 1045 1045 1045 916
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
BLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 8086 9097 8984 8984 22101
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 2049 2049 2049 2049 1793
DETQLM 2111 1244 2161 2218 4727 767
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 0 0 0 0 0
MFWKCE 2128 15000 0 10000 0 16000
MFWKBL 2129 1042 0 2069 0 540
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 0 0 0 0 0
PHDLY2 2134 0 0 0 0 0
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 0 0 0 0 0
POVC22 2163 0 0 0 0 0
POVCLMT2 2164 0 0 0 0 0
MAXCRT 2165 165 185 365 365 185
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 12 24 0 0 12
DCIDBS 2310 0 0 0 0 0
STJG 2302 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate -D(90C8, 90E8)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
- Supporting position feedback for 3-D View (POS3D) of Add 2011.09
Basic Function SERVO GUIDE
- Changes of Standard Parameter Table Add 2011.09
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
図提
番出

Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate-D(90C8, 90E8)
1. Update Edition
90E8 03 Series 0i-D (Series 0i-TD, 2Path System )
- Supporting position feedback for 3-D View (POS3D) of SERVO GUIDE
The position feedback for 3-D View of Servo Tuning Tool FANUC SERVO GUIDE can be observed.
Please refer to (A-95363-05)“Servo Tuning Tool FANUC SERVO GUIDE 3-D View Function” for
the detail of 3-D View Function.

3. Attached
図提
番出

(1) αiS series

αiF 30/3000HV 0255 304
αiF 40/3000HV 0259 309
αiF 40/3000HV Fan 0259 479
*Please refer to Table1 about the standard parameters.
- Dead band parameter (N2004#6) of following motors has been changed to 0.

αiS 50/3000HV Fan 0276 326
αiS 50/3000HV 0276 327
αiS 60/3000HV Fan 0279 329
(2) βiS series

- Standard parameters of βiS12/3000, βiS22/2000 driven by 80A ampplifer have been added.
Motor Model Motor Specification Motor ID No. Driven Amplifer
βiS 12/3000 272(exist) 40A
0078
477 80A
βiS 22/2000 274(exist) 40A
0085
478 80A
図提
番出

βiS12 βiS22
αiF30 αiF40 αiF40
Motor Model 3000 2000
3000HV 3000HV 3000HV Fan
(80A) (80A)
Motor ID Number 304 309 477 478 479
Symbol FS0i,0i Mate-D
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00100000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00001110 00001110 00000000
2014 00000000 00000000 00001110 00001110 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00001010 00011010 00001110 00001110 00011010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 785 1441 804 2368 1441
PK2 2041 -4179 -7513 -4434 -13600 -7513
PK3 2042 -1347 -1350 -1304 -1331 -1350
PK1V 2043 225 188 85 121 188
PK2V 2044 -2016 -1684 -765 -1086 -1684
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 -1882 2253 9920 6992 2253
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 3700 3600 4200 2800 3600
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 -5130 0
PVPA 2057 -7696 -5137 -5130 -3598 -5137
PALPH 2058 -2458 -2027 -1750 -1500 -2027
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 7282 3641 3641 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32501 32501 31932 31744 32501
POVC2 2063 3332 3332 10454 12801 3332
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 9912 9912 5230 6422 9912
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 12288 8192 0 0 8192
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 2259 1876 1181 1309 2607
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 2215 1869 836 1384 1869
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 1291 1044 812 1280 1044
DETQLM 2111 6974 4241 7930 2866 4241
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 3354 6538 1194 2459 6538
MFWKCE 2128 3000 6147 6000 10000 6147
MFWKBL 2129 2833 1809 2056 562 1809
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 5150 3594 5138 3350 3594
PHDLY2 2134 8990 6414 4382 4371 6414
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0
POVC21 2162 32763 32762 32766 32766 32763
POVC22 2163 58 78 31 31 58
POVCLMT2 2164 9912 8288 2752 3379 9912
MAXCRT 2165 85 85 85 85 85
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 36 0 0 36
DCIDBS 2310 0 0 0 0 0
STJG 2302 0 0 0 0 0
LIMLIM 2316 0 0 0 0 0
図提
番出

Notice of the latest version of Standard Parameter Table

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Basic Function - The latest version of Standard Parameter Table Add 2011.10
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
Notice of the latest version
of Standard Parameter Table
DRAW. No. CUST.
B-65270EN/07-044
01 11.10.24 Kameta Newly designed
SHEET
Ed. Date Design Description 1/35
Standard Parameter Table consists of following sections.
1 Standard parameters for AC SERVO MOTOR αi series .............................................................................................. 5

1.1 AC SERVO MOTOR αiS series
1.2 AC SERVO MOTOR αiS series HV *
1.3 AC SERVO MOTOR αiF series
1.4 AC SERVO MOTOR αiF series HV *
1.5 AC SERVO MOTOR αCi series
2 Standard parameters for AC SERVO MOTOR βi series ............................................................................................ 16
2.1 AC SERVO MOTOR βiS series
2.2 AC SERVO MOTOR βiS series HV *
2.3 AC SERVO MOTOR βiSc series
3 Standard parameters for LINEAR MOTOR LiS series ............................................................................................... 23
3.1 LINEAR MOTOR LiS series [200V]
3.2 LINEAR MOTOR LiS series [400V] *
4 Standard parameters for SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series .................................................. 28
4.1 SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series [200V]
4.2 SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series [400V] *
* When HV (400V) - type motor is used with Series 30i/31i/32i/35i-B, and Power Motion i-A, servo software 90G0 / 06.0
or later edition is required.
The following items are required to use the motor which has (*1-*5) in remarks column.
• Servo software of the series and edition listed below or subsequent editions.
• Amplifier and power supply of specification listed below.
(*1)
Amplifier and power supply.
Series Specification Remarks
200V 400V
αi series αiSV A06B-6117-Hxxx A06B-6127-Hxxx
αiPS A06B-6140-Hxxx A06B-6150-Hxxx
βi series βiSV A06B-6130-Hxxx A06B-6131-Hxxx
βiSV(2-axis) A06B-6136-Hxxx ---
A06B-6166-Hxxx ---
βiSVSP A06B-6164-Hxxx ---
βiSVSPc A06B-6167-Hxxx ---
Servo software of the series and edition.
CNC Servo software Remarks
Series Edition
Series 30i/31i/32i/35i-B 90G0 01.0
Power Motion i-A
Series 30i/31i/32i-A 90E0 Q(17)
90E1 01.0
Series 30i/31i-A 90D0 Q(17) HRV4
90E4 01.0 HRV4
Series 0i-D 90C5 01.0
90C8 01.0
90E5 01.0
90E8 01.0
Series 16i/18i/21i-B 90B6 －
90B1 C(03)
Series 0i-C, 20i-B 90B5 －
90B8 C(03)
PMi-H, PDSA 90BP A(01)
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
(*2)
Series Edition
Series 30i/31i/32i/35i-B 90G0 01.0
Power Motion i-A
Series 30i/31i/32i-A 90E0 N(14)
90E1 01.0
Series 30i/31i-A 90D0 N(14) HRV4
90E4 01.0 HRV4
90C8 01.0
90E5 01.0
90E8 01.0
90B1 B(02)
90B8 B(02)
PMi-H, PDSA 90BP A(01)
(*3)
Series Edition
Series 30i/31i/32i/35i-B 90G0 10.0
Power Motion i-A
Series 30i/31i/32i-A 90E0 28.0
90E1 04.0
Series 30i/31i-A 90D0 － HRV4
90E4 04.0 HRV4
Series 0i-D 90C5 －
90C8 －
90E5 －
90E8 －
90B1 －
90B8 －
PMi-H, PDSA 90BP －
(*4)
Series Edition
Series 30i/31i/32i/35i-B 90G0 09.0
Power Motion i-A
Series 30i/31i/32i-A 90E0 30.0
90E1 04.0
Series 30i/31i-A 90D0 － HRV4
90E4 04.0 HRV4
90C8 01.0
90E5 04.0
90E8 01.0
90B1 －
90B8 －
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
(*5)
Series Edition
Series 30i/31i/32i/35i-B 90G0 01.0
Power Motion i-A
Series 30i/31i/32i-A 90E0 N(14)
90E1 01.0
Series 30i/31i-A 90D0 N(14) HRV4
90E4 01.0 HRV4
90C8 01.0
90E5 01.0
90E8 01.0
90B1 －
90B8 －
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1 Standard parameters for AC SERVO MOTOR αi series
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1.1 AC SERVO MOTOR αiS series (1/3)
Motor model 5000 6000 5000 6000 4000 6000 4000 6000 4000 6000 4000
Motor ID No. 262 284 265 466 285 290 288 462 315 452 318
PRM NO Motor ID No.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 530 552 420 395 550 460 570 471 581 605 799
2041 CUR GAIN P -2543 -2288 -1748 -1606 -3449 -1760 -3358 -2249 -3844 -2393 -4447
2042 CUR GAIN 3 -1251 -1252 -1276 -1277 -1307 -1305 -1319 -1321 -1337 -1335 -1317
2043 VEL GAIN I 39 48 64 76 33 53 52 43 69 102 82
2044 VEL GAIN P -350 -429 -574 -678 -294 -478 -466 -387 -616 -914 -733
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 10853 -884 -661 5601 -1289 -794 -815 -980 6163 4150 5175
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 7000 7500 7000 7500 5600 7500 5600 7500 5600 7500 5400
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -10250 -13062 -8974 -13326 -7685 -16398 -5898 -12808 -7687 -12039 -6412
2058 D-PHASE CUR -2000 -1000 -3641 -2500 -2000 -1000 -3000 -1800 -2000 -2000 -2300
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32528 32415 32289 32310 32609 32520 32534 32688 32515 32515 32515
2063 OVC K2 3005 4413 5994 5728 1993 3101 2923 998 3166 3166 3166
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 8936 13146 17889 17091 5920 9224 8692 2960 9418 9418 9418
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 20480 12288 16384 0 8192 0 12288 4096 4096 4096
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1540 1868 2824 2585 1253 2075 1518 1181 1627 1977 1836
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 117 96 127 104 562 346 696 837 1216 819 1470
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 32 1555 8 3092 519 1284 521 528 519 1288 775
2111 TQLIM IN DEC. 8995 11550 10295 8208 7268 10255 6174 10260 6224 12830 6450
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 1137 1137 646 660 2106 801 1592 1146 2041 1000 1871
2128 MFWKCE 1000 3000 1667 3000 4000 1000 2000 667 2500 1000 4000
2129 MFWKBL 3851 4112 3847 4365 2580 5388 2575 3850 2580 3854 2574
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 7690 7690 7690 7690 5150 10250 6174 7690 5150 7690 5150
2134 PHDLY2 12840 7740 12840 12830 8990 12830 8990 8990 8990 8990 8990
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 128 128 128
2162 OVC2 K1 32766 32766 32762 32763 32767 32765 32766 32764 32766 32765 32765
2163 OVC2 K2 20 30 77 58 13 38 19 45 28 44 37
2164 OVC2 LIMIT 3776 5554 12702 9912 2501 6857 3672 1721 5177 7743 6687
2165 MAX CURRENT 25 25 25 25 85 85 85 165 165 165 165
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model 4000 2000 3000 3000 2000 3000 2500 2500 2500 2500 2000
Fan Fan Fan Fan
Motor ID No. 322 468 324 325 470 328 335 330 338 334 342
PRM NO SERVO PRM. Amp*2
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 712 1539 547 547 1358 1191 1020 1020 1834 1834 1659
2041 CUR GAIN P -4138 -7321 -3423 -3423 -6767 -6320 -7093 -7093 -7805 -7805 -8045
2042 CUR GAIN 3 -1341 -1344 -1345 -1345 -1344 -1347 -1359 -1359 -1360 -1360 -1354
2043 VEL GAIN I 92 90 69 69 103 69 91 91 115 115 114
2044 VEL GAIN P -827 -802 -622 -622 -925 -617 -819 -819 -1026 -1026 -1025
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 4589 4731 6099 6099 4103 6152 4632 4632 3699 3699 3709
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 4800 2800 4200 4200 2700 4000 3500 3500 3100 3100 2800
2053 DB-CMP PPMAX 21 31979 31979 31979 31979 31979 21 21 21 21 21
2054 DB-CMP PDDP 1894 3 3 3 3 3 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -5645 -3867 -5638 -5638 -3097 -4619 -4368 -4368 -3090 -3090 -3081
2058 D-PHASE CUR -3000 -3393 -1000 -1000 -2995 -2000 -1359 -1359 -2700 -2700 -700
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32515 32515 32558 32348 32515 32388 32310 32309 32309 32309 32391
2063 OVC K2 3166 3166 2627 5245 3166 4744 5728 5734 5734 5734 4714
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 9418 9418 7810 15639 9418 14138 15662 27346 27346 27346 23263
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 4096 8192 4096 4096 0 8192 20480 20480 12288 12288 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 2073 1856 1439 2037 2018 1937 1960 2848 2712 3013 2386
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 1701 2569 3312 3312 2942 4411 4589 4589 5973 5973 10871
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 776 1032 519 519 1544 519 776 776 1290 1290 1296
2111 TQLIM IN DEC. 5682 4954 6174 6174 3151 5220 3787 3787 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 1853 2825 2046 2046 5498 2852 3520 3520 3518 3518 3817
2128 MFWKCE 4000 4601 6500 6500 4004 5000 6500 6500 4000 4000 7000
2129 MFWKBL 2063 1296 2063 2063 1302 1300 1297 1297 1298 1298 1301
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 5150 2570 5150 5150 4146 5150 2570 2570 3092 3092 2574
2134 PHDLY2 8988 12814 8990 8990 12821 8990 8970 8970 12826 12826 12814
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 128 128 0 0 128 0 106 140 140 140 140
2162 OVC2 K1 32765 32764 32754 32739 32761 32742 32750 32745 32745 32745 32738
2163 OVC2 K2 38 51 174 365 81 327 223 292 292 292 375
2164 OVC2 LIMIT 6846 6831 3300 6608 8124 5973 6581 13952 13952 13952 13952
2165 MAX CURRENT 165 165 365 365 165 365 365 365 365 365 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
αiS500
Motor model 2000
Motor specification 0295

Motor ID No. 345
2003 00001000
2004 00000011
2005 00000000
2006 00000000
2007 00000000
2008 00000000
2009 00000000
2010 00000000
2011 00000000
2012 00000000
2013 00000000
2014 00000000
2210 00000000
2211 00001010
2300 00000000
2301 00000000
2040 CUR GAIN I 2660
2041 CUR GAIN P -10235
2042 CUR GAIN 3 -1355
2043 VEL GAIN I 134
2044 VEL GAIN P -1199
2045 VEL GAIN 3 0
2046 VEL GAIN 4 -8235
2047 OBSERVER POA1 3164
2048 BLACC CMP 0
2049 DPFMX 0
2050 OBSERVER POK1 956
2052 OVER SPEED 2400
2053 DB-CMP PPMAX 21
2054 DB-CMP PDDP 1894
2055 DB-CMP PHYST 319
2056 EMFCMP 0
2057 D-PHASE CUR -2068
2059 PPBAS 0
2060 TCMD LIMIT 7282
2061 EMFLMT 0
2062 OVC K1 32309
2063 OVC K2 5734
2064 TGALMLV 4
2065 OVC LIMIT 27346
2066 ACC FB GAIN 0
2067 TCMD FILTER 0
2068-2073 0
2074 AALPH 12288
2077-2083 0
2086 RATED CURRENT 2980
2087-2098 0
2099 ONEPSL 400
2100 INPA1 0
2101 INPA2 0
2102 DBLIM 0
2103 ABVOF 0
2104 ABTSH 0
2105 TORQUE CONST. 15096
2106-2109 0
2110 MGSTCM 1296
2111 TQLIM IN DEC. 0
2112 AMRDML 0
2113 HRV FILT 0
2127 NINTCT 4175
2128 MFWKCE 4000
2129 MFWKBL 1041
2130-2132 SMOOTH CMP 0
2133 PHDLY1 2069
2134 PHDLY2 8981
2159 DGCSMM 0
2160 TRQCUP 0
2161 OVC STP 140
2162 OVC2 K1 32745
2163 OVC2 K2 292
2164 OVC2 LIMIT 13952
2165 MAX CURRENT 365
2302 TQLIM AT STOP 0
2304 ACCBSLM 0
2305 ACDCEBD 0
2310 DCIDBS 0
2316 LIMLIM 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1.2 AC SERVO MOTOR αiS series HV (1/4)
Motor model 5000HV 6000HV 5000HV 6000HV 4000HV 6000HV 4000HV 6000HV 4000HV 6000HV 4000HV
Motor ID No. 263 287 266 467 286 292 289 463 316 453 319
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 400 497 425 432 694 381 783 471 709 605 816
2041 CUR GAIN P -2312 -2371 -1641 -1673 -3858 -1749 -4294 -2249 -4008 -2393 -4681
2042 CUR GAIN 3 -1251 -1249 -1266 -1266 -1318 -1305 -1333 -1321 -1345 -1335 -1348
2043 VEL GAIN I 39 48 64 77 34 53 52 43 76 102 82
2044 VEL GAIN P -351 -429 -574 -688 -306 -478 -470 -387 -685 -914 -738
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -1081 -884 -661 5516 -1240 -794 -808 -980 5538 4150 5143
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 7000 7500 7000 7500 5600 7500 5600 7500 5600 7500 5400
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -10252 -13062 -10262 -13326 -7685 -16398 -5898 -12808 -7683 -12039 -6412
2058 D-PHASE CUR -1600 -1200 -3300 -2500 -2000 -1000 -3000 -1800 -1000 -2000 -2300
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32532 32416 32289 32288 32596 32548 32530 32688 32501 32501 32501
2063 OVC K2 2953 4405 5994 5995 2153 2755 2976 998 3332 3332 3332
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 8782 13123 17889 17893 6396 8192 8848 2960 9912 9912 9912
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 16384 20480 8192 16384 8192 8192 8192 12288 8192 4096 4096
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1526 1866 2824 2586 1302 2075 1532 1181 1810 1977 1847
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 117 96 127 104 541 346 690 837 1093 819 1460
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 40 1555 40 3092 519 1284 521 528 513 1288 775
2111 TQLIM IN DEC. 10260 11550 10260 8208 7268 10255 6159 10260 6194 12830 6430
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 4548 2302 1293 1368 5103 1600 4904 2292 4264 2000 5117
2128 MFWKCE 1250 2200 3000 3000 4500 1400 2000 667 2000 1000 3000
2129 MFWKBL 3847 4112 5122 4365 2580 5390 2575 3850 3092 3854 2574
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 7690 7690 7685 7690 5150 10260 6174 7690 5150 7690 5150
2134 PHDLY2 12850 7740 12850 12830 8990 12835 8990 8990 8990 8990 8990
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 32766 32766 32762 32763 32767 32765 32766 32764 32766 32765 32766
2163 OVC2 K2 20 30 77 63 14 38 20 45 28 34 30
2164 OVC2 LIMIT 3711 5544 12702 10651 2702 6857 3738 1721 5218 6222 5432
2165 MAX CURRENT 10 10 10 10 45 45 45 85 85 85 85
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Fan Fan Fan Fan
Motor ID No. 323 469 327 326 471 329 336 331 339 337 343
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00100000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010 00001010 00000000 00000000 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 860 1539 705 705 1358 1131 1790 1790 2080 2080 1327
2041 CUR GAIN P -4938 -7321 -4855 -4855 -6767 -5966 -5915 -5915 -8139 -8139 -7279
2042 CUR GAIN 3 -1350 -1344 -1348 -1348 -1344 -1345 -1359 -1359 -1359 -1359 -1356
2043 VEL GAIN I 93 90 70 70 103 69 91 91 115 115 114
2044 VEL GAIN P -831 -802 -628 -628 -925 -617 -819 -819 -1026 -1026 -1025
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 4569 4731 6039 6039 4103 6152 4636 4636 3699 3699 3703
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 4800 2800 4200 4200 2700 4000 3500 3500 3100 3100 2800
2053 DB-CMP PPMAX 21 31979 31979 31979 31979 31979 21 21 21 21 21
2054 DB-CMP PDDP 1894 3 3 3 3 3 1894 1894 1894 1894 3787
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -5648 -3867 -5638 -5638 -3097 -4620 -3846 -3846 -3088 -3088 -3846
2058 D-PHASE CUR -3000 -3393 -1000 -1000 -2995 -2000 -900 -900 -3000 -3000 -900
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32501 32501 32554 32371 32501 32388 32474 32309 32309 32309 32391
2063 OVC K2 3332 3332 2680 4967 3332 4745 3672 5734 5734 5734 4714
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 9912 9912 7968 14807 9912 14140 15982 27346 27346 27346 23263
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 4096 8192 0 0 0 4096 12288 12288 12288 12288 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 2083 1856 1454 2057 2018 1937 2033 2848 2712 3013 2483
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 10000 10000 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 1693 2569 3279 3279 2942 4411 4423 4423 5973 5973 10871
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 769 1032 519 519 1544 519 1291 1291 1291 1291 1296
2111 TQLIM IN DEC. 5682 4954 6174 6174 3151 5220 0 0 3428 3428 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 5230 5651 4861 4861 5498 5393 6952 6952 6729 6729 7634
2128 MFWKCE 4000 4601 2500 2500 4004 3000 2000 2000 4000 4000 5000
2129 MFWKBL 2063 1296 2068 2068 1302 1300 1549 1549 1551 1551 1298
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 5150 2570 5150 5150 4146 5150 0 0 2575 2575 2574
2134 PHDLY2 8988 12814 8990 8990 12821 8990 0 0 8984 8984 12814
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 140 140 140 140 140
2162 OVC2 K1 32765 32764 32754 32738 32764 32742 32759 32745 32745 32745 32738
2163 OVC2 K2 38 48 178 373 51 327 112 292 292 292 375
2164 OVC2 LIMIT 6908 6829 3366 6736 7077 5974 6752 13952 13952 13952 13952
2165 MAX CURRENT 85 85 185 185 85 185 185 185 185 185 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
spindle
Motor ID No. 344 346 347 348 458 350 465 454 459 476 455
PRM NO SERVO PRM. Amp*2 Amp*2 Amp*4(PDM) Amp*4 Amp*4(PDM) Amp*4 Amp*4 Amp*4(PDM)
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 01000011 00000011 01000011 01000011 00000011 00000011 01000011 01000011 01000011 01000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00001000 00000000 00001000 00000000 00001000 00001000 00001000 00000000 00000000 00001000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00100000 00100000 00100000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000001 00000000 00000001 00000000 00000000 00000001
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00011010 00001010 00011010 00001010 00011010 00011010 10011010 00011110 10011110 10011110 00011010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 10000000 10000000 11000000 11000000 11000000 11000000
2040 CUR GAIN I 821 2255 1344 840 1260 960 960 643 643 643 772
2041 CUR GAIN P -5450 -10049 -7296 -5329 -8010 -6554 -6554 -3600 -3600 -3600 -3819
2042 CUR GAIN 3 -1355 -1356 -1357 -1361 -1362 -1362 -1362 -1358 -1358 -1358 -1357
2043 VEL GAIN I 91 134 111 234 263 191 191 502 502 502 652
2044 VEL GAIN P -819 -1199 -996 -2096 -2357 -1708 -1708 -4500 -4500 -4500 -5836
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 4633 3164 3811 1811 1610 2221 2221 843 843 843 650
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 3900 2400 4200 2600 2600 3800 3800 2400 2400 2400 2800
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 3787 1894 3787 3787 1894 1894 3787 3787 3787 3787
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -5646 -2070 -3856 -2320 -2320 -4620 -4620 -3363 -3363 -3363 -2088
2058 D-PHASE CUR -1800 -2700 -2900 -2500 -2500 -2500 -2500 -3200 -3200 -3200 -5000
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 7282 7282 7282 7282 5097 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32380 32309 32380 32309 32309 32488 32488 32309 32309 32309 32309
2063 OVC K2 4850 5734 4850 5734 5734 3503 3503 5734 5734 5734 5734
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 12155 27346 12155 27346 27346 18280 18280 27346 27346 27346 27346
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 12288 12288 12288 12288 12288 12288 12288 12288 12288 12288 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 2000 2980 2482 2834 2960 2599 2599 2893 2893 2893 3187
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 2000 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 13494 15096 18125 28573 27963 3807 3807 5957 5957 5957 8472
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 523 1293 521 1296 785 1040 1040 784 784 784 267
2111 TQLIM IN DEC. 2960 0 2953 3172 2300 3242 3242 2022 2022 2720 2218
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 7720 8341 8021 8637 11851 9876 9876 3449 3449 3449 3029
2128 MFWKCE 4300 4500 2500 6000 4500 4500 4500 3000 3000 3000 2700
2129 MFWKBL 1556 788 1041 1047 1038 1556 1556 1291 1291 1291 777
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 3100 2324 3093 2580 2570 2580 2580 2060 2060 2060 2068
2134 PHDLY2 6422 8984 6418 8985 12810 6418 6418 12820 12820 12820 6410
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 140 140 140 140 140 140 140 140 140 140 140
2162 OVC2 K1 32700 32745 32700 32745 32745 32721 32721 32745 32745 32745 32745
2163 OVC2 K2 853 292 853 292 292 589 589 292 292 292 292
2164 OVC2 LIMIT 10644 13952 10644 13952 13952 13952 13952 13952 13952 13952 13952
2165 MAX CURRENT 0 365 0 365 365 0 365 0 365 365 0
2302 TQLIM AT STOP 20 0 20 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 2720 2720 2720 0
2305 ACDCEBD 29 0 32 0 22 29 29 4112 4112 4112 22
2310 DCIDBS 1700 0 1400 0 1112 1648 1648 1236 1236 1236 1112
2316 LIMLIM 5394 0 5394 0 0 0 0 0 0 0 0
Remarks *1,*2,*3 *1,*2,*3 *1,*2,*3 *1,*2,*3 *1,*2,*3 *1,*2 *1,*2 *1,*2,*3,*4 *1,*2
*1 The corresponding servo software, amplifier and power supply are required.
*2,*3,*4 The corresponding servo software is required.
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
αiS3000
Motor model 2000HV
Motor specification 0092

Motor ID No. 460
2003 00001000
2004 01000011
2005 00000000
2006 00000000
2007 00100000
2008 00000000
2009 00000000
2010 00000000
2011 00000000
2012 00000000
2013 00000000
2014 00000000
2210 00000000
2211 10011010
2300 00000000
2301 11000000
2040 CUR GAIN I 772
2041 CUR GAIN P -3819
2042 CUR GAIN 3 -1357
2043 VEL GAIN I 652
2044 VEL GAIN P -5836
2045 VEL GAIN 3 0
2046 VEL GAIN 4 -8235
2048 BLACC CMP 0
2049 DPFMX 0
2052 OVER SPEED 2800
2056 EMFCMP 0
2059 PPBAS 0
2061 EMFLMT 0
2062 OVC K1 32309
2063 OVC K2 5734
2064 TGALMLV 4
2065 OVC LIMIT 27346
2066 ACC FB GAIN 0
2067 TCMD FILTER 0
2068-2073 0
2074 AALPH 12288
2077-2083 0
2087-2098 0
2099 ONEPSL 400
2100 INPA1 0
2101 INPA2 0
2102 DBLIM 0
2103 ABVOF 0
2104 ABTSH 0
2106-2109 0
2110 MGSTCM 267
2111 TQLIM IN DEC. 2218
2112 AMRDML 0
2113 HRV FILT 0
2127 NINTCT 3029
2128 MFWKCE 2700
2129 MFWKBL 777
2133 PHDLY1 2068
2134 PHDLY2 6410
2159 DGCSMM 0
2160 TRQCUP 0
2161 OVC STP 140
2162 OVC2 K1 32745
2163 OVC2 K2 292
2164 OVC2 LIMIT 13952
2304 ACCBSLM 0
2305 ACDCEBD 22
2310 DCIDBS 1112
2316 LIMLIM 0
Remarks *1,*2
*2 The corresponding servo software is required.
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1.3 AC SERVO MOTOR αiF series
αiF1 αiF2 αiF4 αiF8 αiF12 αiF22 αiF30 αiF40 αiF40
Motor model 5000 5000 4000 3000 3000 3000 3000 3000 3000
Fan
Motor ID No. 252 255 273 277 293 297 303 307 308
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00100000 00100000 00100000 00100000 00000000 00100000 00100000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00000010 00000000 00000000 00000000 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 620 760 993 787 1701 1750 768 1500 1500
2041 CUR GAIN P -3034 -3743 -4260 -4184 -6391 -6000 -4492 -8224 -8224
2042 CUR GAIN 3 -1256 -1283 -1311 -1325 -1315 -1345 -1347 -1348 -1348
2043 VEL GAIN I 66 76 106 113 192 198 230 191 191
2044 VEL GAIN P -594 -680 -953 -1009 -1721 -1775 -2057 -1712 -1712
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 6384 5578 3980 3760 2204 2137 1845 2216 2216
2048 BLACC CMP 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 7000 7000 5600 4200 4800 3600 4800 4200 4200
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319
2056 EMFCMP -5130 -10 -5130 0 0 0 -20500 0 0
2057 D-PHASE CUR 0 -12298 -11789 -6420 -8199 -5136 -8465 -2570 -2570
2058 D-PHASE CUR 0 -1275 -180 -2000 -747 -2800 -1657 -2000 -2000
2059 PPBAS 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 8010 8010 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0
2062 OVC K1 32613 32497 32446 32383 32520 32520 32515 32515 32431
2063 OVC K2 1933 3390 4029 4807 3101 3101 3166 3166 4212
2064 TGALMLV 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 5739 10085 11998 14327 9224 9224 9418 9418 12545
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 12288 8192 8192 8192 12288 4096 0 0
2077-2083 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1234 1636 1784 1950 2085 2131 2306 1957 2593
2087-2098 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 15000 15000 15000 15000 0 12000 12000
2103 ABVOF 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 72 109 201 369 517 929 1170 1839 1839
2106-2109 0 0 0 0 0 0 0 0 0
2110 MGSTCM 32 32 32 776 32 1291 1032 1291 1291
2111 TQLIM IN DEC. 10260 10280 5130 3870 0 0 7735 5220 5140
2112 AMRDML 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0
2127 NINTCT 1188 1276 1443 2103 2388 3272 1688 3041 3041
2128 MFWKCE 1667 2000 2000 3500 2000 4500 2500 6000 2000
2129 MFWKBL 3858 3862 3338 1815 2568 1301 2829 1560 1553
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0
2133 PHDLY1 7690 7693 6670 0 0 0 5140 2590 3085
2134 PHDLY2 12840 12840 8980 0 0 0 8995 8990 8990
2159 DGCSMM 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 128 128 128
2162 OVC2 K1 32767 32766 32766 32765 32765 32765 32764 32764 32717
2163 OVC2 K2 13 23 27 33 38 40 48 46 637
2164 OVC2 LIMIT 2425 4261 5069 6053 6924 7229 8124 8124 10815
2165 MAX CURRENT 25 25 45 45 85 85 165 165 165
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 1817 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0
Remarks *1
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1.4 AC SERVO MOTOR αiF series HV
αiF4 αiF8 αiF12 αiF22 αiF30 αiF40 αiF40
Motor model 4000HV 3000HV 3000HV 3000HV 3000HV 3000HV 3000HV
Fan
Motor ID No. 275 279 295 299 304 309 479
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00100000 00100000 00100000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00000000 00000000 00001010 00011010 00011010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 570 1222 1200 1919 785 1441 1441
2041 CUR GAIN P -3578 -5890 -6059 -9132 -4179 -7513 -7513
2042 CUR GAIN 3 -1309 -1322 -1339 -1346 -1347 -1350 -1350
2043 VEL GAIN I 113 113 193 197 225 188 188
2044 VEL GAIN P -1009 -1008 -1727 -1765 -2016 -1684 -1684
2045 VEL GAIN 3 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 3762 3764 2197 2150 -1882 2253 2253
2048 BLACC CMP 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510
2052 OVER SPEED 5400 3900 4800 3600 3700 3600 3600
2053 DB-CMP PPMAX 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0
2057 D-PHASE CUR 0 -6159 -8203 -5136 -7696 -5137 -5137
2058 D-PHASE CUR 0 -1261 -1178 -2824 -2458 -2027 -2027
2059 PPBAS 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 8010 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0
2062 OVC K1 32433 32433 32548 32548 32501 32501 32501
2063 OVC K2 4184 4184 2755 2755 3332 3332 3332
2064 TGALMLV 4 4 4 4 4 4 4
2065 OVC LIMIT 12461 12461 8192 8192 9912 9912 9912
2066 ACC FB GAIN 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0
2074 AALPH 12288 12288 12288 8192 12288 8192 8192
2077-2083 0 0 0 0 0 0 0
2086 RATED CURRENT 1888 1948 2092 2118 2259 1876 2607
2087-2098 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0
2102 DBLIM 0 0 15000 15000 0 0 0
2103 ABVOF 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0
2105 TORQUE CONST. 190 369 516 934 2215 1869 1869
2106-2109 0 0 0 0 0 0 0
2110 MGSTCM 1032 782 774 787 1291 1044 1044
2111 TQLIM IN DEC. 0 0 0 0 6974 4241 4241
2112 AMRDML 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0
2127 NINTCT 2573 4191 4787 6547 3354 6538 6538
2128 MFWKCE 4000 6000 4000 6000 3000 6147 6147
2129 MFWKBL 3348 1810 2320 1808 2833 1809 1809
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0
2133 PHDLY1 5130 5150 0 0 5150 3594 3594
2134 PHDLY2 8990 8990 0 0 8990 6414 6414
2159 DGCSMM 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0
2162 OVC2 K1 32766 32765 32765 32765 32763 32762 32763
2163 OVC2 K2 31 33 39 40 58 78 58
2164 OVC2 LIMIT 5676 6042 6969 7142 9912 8288 9912
2165 MAX CURRENT 25 25 45 45 85 85 85
2302 TQLIM AT STOP 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0
Remarks *2 *2
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
1.5 AC SERVO MOTOR αCi series
αC4 αC8 αC12 αC22 αC30
Motor model 3000i 2000i 2000i 2000i 1500i

Motor ID No. 271 276 291 296 301
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00100000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00000010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 1240 1276 1875 2320 2238
2041 CUR GAIN P -6415 -6288 -9137 -10593 -13330
2042 CUR GAIN 3 -1309 -1326 -1339 -1347 -1347
2043 VEL GAIN I 115 150 280 271 166
2044 VEL GAIN P -1034 -1342 -2504 -2426 -1486
2045 VEL GAIN 3 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 3670 2827 1516 1565 2553
2048 BLACC CMP 0 0 0 0 0
2049 DPFMX 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510
2052 OVER SPEED 4200 2800 2800 2400 2100
2053 DB-CMP PPMAX 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0
2057 D-PHASE CUR -5915 -3854 -1804 -2597 -1545
2058 D-PHASE CUR -1500 -1236 -2500 -1942 -1300
2059 PPBAS 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 8010 7282
2061 EMFLMT 0 0 0 0 0
2062 OVC K1 32406 32289 32289 32114 32520
2063 OVC K2 4529 5994 5994 8171 3101
2064 TGALMLV 4 4 4 4 4
2065 OVC LIMIT 13493 17889 17889 24454 9224
2066 ACC FB GAIN 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0
2068-2073 0 0 0 0 0
2074 AALPH 12288 8192 8192 4096 8192
2077-2083 0 0 0 0 0
2086 RATED CURRENT 1892 2593 3020 2911 1655
2087-2098 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400
2100 INPA1 0 0 0 0 0
2101 INPA2 0 0 0 0 0
2102 DBLIM 0 0 15000 0 0
2103 ABVOF 0 0 0 0 0
2104 ABTSH 0 0 0 0 0
2105 TORQUE CONST. 190 277 350 680 1630
2106-2109 0 0 0 0 0
2110 MGSTCM 1289 1552 0 1548 2059
2111 TQLIM IN DEC. 3900 3880 2168 2600 2148
2112 AMRDML 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0
2127 NINTCT 2544 2380 4150 3695 6680
2128 MFWKCE 5000 4500 12000 4000 14000
2129 MFWKBL 1812 1550 1044 1046 539
2130-2132 SMOOTH CMP 0 0 0 0 0
2133 PHDLY1 3855 3860 5150 2070 1054
2134 PHDLY2 8995 8990 8990 9000 9000
2159 DGCSMM 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0
2161 OVC STP 0 0 0 0 0
2162 OVC2 K1 32766 32763 32761 32761 32766
2163 OVC2 K2 31 63 91 83 23
2164 OVC2 LIMIT 5701 10709 14518 13493 4361
2165 MAX CURRENT 25 25 25 45 85
2302 TQLIM AT STOP 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
2 Standard parameters for AC SERVO MOTOR βi series
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
2.1 AC SERVO MOTOR βiS series (1/4)
βiS0.2 βiS0.3 βiS0.4 βiS0.5 βiS1 βiS2 βiS2 βiS4 βiS4 βiS8 βiS8
Motor model 5000 5000 5000 6000 6000 4000 4000 4000 4000 3000 3000
40A 40A 40A
Motor specification 0111 0112 0114 0115 0116 0061-Bxx3 0061-Bxx3 0063-Bxx3 0063-Bxx3 0075-Bxx3 0075-Bxx3
Motor ID No. 260 261 280 281 282 253 254 256 257 258 259
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000100 00010000 00000000 00001110 00000000 00001110
2014 00000000 00000000 00000000 00000000 00000000 00000100 00010000 00000000 00001110 00000000 00001110
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00000010 00000010 00000010 00001010 00001010 00001110 00001110 00001110 00001110 00001110 00001110
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 123 210 100 138 312 360 720 400 800 650 1160
2041 CUR GAIN P -510 -970 -430 -673 -1360 -1920 -3840 -1920 -3840 -3831 -5600
2042 CUR GAIN 3 -1069 -1146 -2463 -1205 -1203 -1237 -1237 -1253 -1253 -1299 -1299
2043 VEL GAIN I 4 4 7 7 6 78 39 112 56 164 82
2044 VEL GAIN P -36 -33 -61 -59 -53 -698 -349 -1008 -504 -1476 -738
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -10638 -11550 -6249 -6462 -7176 -1089 -2178 -753 -1506 5143 -1029
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 7000 7000 7000 7500 7500 5600 5600 5600 5600 4200 4200
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 -12850 -12850 -12850 0 0 0 0 -2570 0
2057 D-PHASE CUR 0 0 0 0 -15114 -10250 -10245 -7694 -7687 -5140 -5131
2058 D-PHASE CUR 0 0 0 0 -1200 -1000 -500 -2800 -1400 -3200 -1600
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 5826 7282 7282 6554 3277 7282 3641 7282 3641
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32725 32725 32640 32674 32695 32531 32531 32289 32289 32289 32289
2063 OVC K2 533 533 1603 1178 915 2963 2963 5988 5988 5994 5994
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 3163 3163 4759 3497 2714 8811 2203 17873 4468 17889 4472
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 20480 20480 20480 20480 16384 0 20480 0 16384 0
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1929 1929 1605 1376 1212 1529 764 2178 1089 2780 1390
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 7 14 22 42 89 119 238 146 292 226 452
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 1 1 30 25 1556 1048 815 780 532 1807 1045
2111 TQLIM IN DEC. 7710 7700 10290 10290 10290 11600 11600 7790 7790 7930 7930
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 379 852 400 504 881 1172 1172 796 796 1442 1442
2128 MFWKCE 0 3000 0 0 1500 2500 5000 3000 6000 3500 7000
2129 MFWKBL 0 3880 0 0 5135 3358 3358 3392 3392 1298 1298
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 7700 7695 7690 7690 15400 7192 7192 8992 8992 3858 3858
2134 PHDLY2 12825 12840 12820 12820 12840 8990 8990 12864 9024 8990 8990
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 32766 32767 32767 32766 32766 32765 32765 32762 32762
2163 OVC2 K2 0 0 22 16 12 20 20 42 42 74 74
2164 OVC2 LIMIT 0 0 4104 3015 2340 3723 931 7551 1888 12305 3076
2165 MAX CURRENT 4 4 25 25 25 25 45 25 45 25 45
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
βiS2 βiS2 βiS2 βiS4 βiS4 βiS4 βiS4 βiS8 βiS8 βiS8 βiS8
Motor model 4000 4000 4000 4000 4000 4000 4000 3000 3000 3000 3000
40A FS0i FS0i,40A 40A FS0i FS0i,40A 40A FS0i FS0i,40A
Motor specification 0061-Bxx3 0061-Bxx6 0061-Bxx6 0063-Bxx3 0063-Bxx3 0063-Bxx6 0063-Bxx6 0075-Bxx3 0075-Bxx3 0075-Bxx6 0075-Bxx6
Motor ID No. 254 306 310 256 257 311 312 258 259 283 294
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00010000 00000100 00010000 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110
2014 00010000 00000100 00010000 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 720 360 720 400 800 400 800 650 1160 650 1160
2041 CUR GAIN P -3840 -1920 -3840 -1920 -3840 -1920 -3840 -3831 -5600 -3831 -5600
2042 CUR GAIN 3 -1237 -1237 -1237 -1253 -1253 -1253 -1253 -1299 -1299 -1299 -1299
2043 VEL GAIN I 39 78 39 112 56 112 56 164 82 164 82
2044 VEL GAIN P -349 -698 -349 -1008 -504 -1008 -504 -1476 -738 -1476 -738
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -2178 -1089 -2178 -753 -1506 -753 -1506 5143 -1029 5143 -1029
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 5600 5600 5600 5600 5600 5600 5600 4200 4200 4200 4200
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 -2570 0 -2570 0
2057 D-PHASE CUR -10245 -10250 -10245 -7694 -7687 -7694 -7687 -5140 -5131 -5140 -5131
2058 D-PHASE CUR -500 -1000 -500 -2800 -1400 -2800 -1400 -3200 -1600 -3200 -1600
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 3277 6554 3277 7282 3641 7282 3641 7282 3641 7282 3641
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32531 32652 32739 32289 32289 32532 32709 32289 32289 32381 32671
2063 OVC K2 2963 1455 364 5988 5988 2945 738 5994 5994 4835 1214
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 2203 4317 1079 17873 4468 8758 2189 17889 4472 14410 3603
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 0 16384 0 20480 0 20480 0 16384 0 16384 0
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 764 1529 764 2178 1089 2178 1089 2780 1390 2780 1390
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 238 119 238 146 292 146 292 226 452 226 452
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 815 1048 815 780 532 780 532 1807 1045 1807 1045
2111 TQLIM IN DEC. 11600 11600 11600 7790 7790 7790 7790 7930 7930 7930 7930
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 1172 1172 1172 796 796 796 796 1442 1442 1442 1442
2128 MFWKCE 5000 2500 5000 3000 6000 3000 6000 3500 7000 3500 7000
2129 MFWKBL 3358 3358 3358 3392 3392 3392 3392 1298 1298 1298 1298
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 7192 7192 7192 8992 8992 8992 8992 3858 3858 3858 3858
2134 PHDLY2 8990 8990 8990 12864 9024 12864 9024 8990 8990 8990 8990
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 120 120 0 0 120 120 0 0 0 0
2162 OVC2 K1 32766 32757 32765 32765 32765 32745 32762 32762 32762 32764 32767
2163 OVC2 K2 20 140 34 42 42 294 70 74 74 51 12
2164 OVC2 LIMIT 931 2665 666 7551 1888 5407 1352 12305 3076 8896 2224
2165 MAX CURRENT 45 25 45 25 45 25 45 25 45 25 45
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
βiS12 βiS12 βiS12 βiS12 βiS12 βiS12 βiS22 βiS22 βiS22 βiS22 βiS22
Motor model 2000 2000 2000 2000 3000 3000 1500 1500 2000 2000 3000
40A FS0i FS0i,40A 80A FS0i FS0i,40A 80A
Motor specification 0077-Bxx3 0077-Bxx3 0077-Bxx6 0077-Bxx6 0078 0087 0084-Bxx6 0084-Bxx6 0085 0089 0082
Motor ID No. 269 268 298 300 272 477 302 305 274 478 313
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110 00001000
2014 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110 00001000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 547 1094 547 1094 402 804 2171 4342 1184 2368 1157
2041 CUR GAIN P -3289 -6578 -3289 -6578 -2217 -4434 -8178 -16356 -6800 -13600 -5102
2042 CUR GAIN 3 -1305 -1305 -1305 -1305 -1304 -1304 -1329 -1329 -1331 -1331 -1332
2043 VEL GAIN I 230 115 230 115 170 85 280 140 242 121 198
2044 VEL GAIN P -2054 -1027 -2054 -1027 -1530 -765 -2507 -1254 -2172 -1086 -1766
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 3695 7390 3695 7390 4960 9920 3027 6054 3496 6992 4297
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 2800 2800 2800 2800 4200 4200 1800 1800 2800 2800 4200
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 -5130 -5130 0
2057 D-PHASE CUR -3884 -3862 -3884 -3862 -5140 -5130 -2110 -2079 -3612 -3598 -6174
2058 D-PHASE CUR -4350 -2175 -4350 -2175 -3500 -1750 -4691 -2342 -3000 -1500 -2843
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 3641 7282 3641 7282 3641 7282 3641 7282 3641 5462
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32284 32646 32323 32646 32205 31932 32319 32655 32106 31744 32520
2063 OVC K2 6045 1525 5566 1525 7041 10454 5617 1411 8275 12801 3097
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 18045 4511 16603 4511 21044 5230 16756 4189 24770 6422 9212
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 8192 0 8192 0 16384 0 8192 0 16384 0 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 3126 1563 3126 1563 2363 1181 3012 1506 2618 1309 2121
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 315 630 315 630 418 836 597 1194 692 1384 848
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 1 1282 1 1282 1814 812 1025 514 0 1280 1289
2111 TQLIM IN DEC. 3940 3940 3940 3940 7930 7930 2248 2248 2866 2866 7268
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 1350 1350 1350 1350 1194 1194 3290 3290 2459 2459 1967
2128 MFWKCE 4000 8000 4000 8000 3000 6000 5500 11000 5000 10000 6000
2129 MFWKBL 280 280 280 280 2056 2056 1032 1032 562 562 2315
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 3614 3614 3614 3614 5138 5138 2580 2580 3350 3350 5647
2134 PHDLY2 8980 4372 8980 4372 8990 4382 8990 4382 8979 4371 12820
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 32760 32766 32763 32767 32764 32766 32763 32767 32763 32766 32765
2163 OVC2 K2 99 21 60 15 51 31 60 14 64 31 40
2164 OVC2 LIMIT 15559 3890 10250 2785 8891 2752 10345 2586 10913 3379 7166
2165 MAX CURRENT 25 45 25 45 45 85 25 45 45 85 85
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
βiS30 βiS40
Motor model 2000 2000
Motor specification 0087 0089

PRM NO SERVO PRM.
2003 00001000 00001000
2004 00000011 00000011
2005 00000000 00000000
2006 00000000 00000000
2007 00000000 00000000
2008 00000000 00000000
2009 00000000 00000000
2010 00000000 00000000
2011 00000000 00000000
2012 00000000 00000000
2013 00000010 00000010
2014 00000010 00000010
2210 00000000 00000000
2211 00001010 00001010
2300 00000000 00000000
2301 00000000 00000000
2040 CUR GAIN I 1650 1624
2041 CUR GAIN P -6565 -7197
2042 CUR GAIN 3 -2681 -1341
2043 VEL GAIN I 214 208
2044 VEL GAIN P -1912 -1870
2045 VEL GAIN 3 0 0
2046 VEL GAIN 4 -8235 -8235
2047 OBSERVER POA1 3971 4057
2048 BLACC CMP 0 0
2049 DPFMX 0 0
2050 OBSERVER POK1 956 956
2051 OBSERVER POK2 510 510
2052 OVER SPEED 2800 2600
2053 DB-CMP PPMAX 21 21
2054 DB-CMP PDDP 1894 1894
2055 DB-CMP PHYST 319 319
2056 EMFCMP 0 0
2057 D-PHASE CUR -4647 -3375
2058 D-PHASE CUR -3115 -3862
2059 PPBAS 0 0
2060 TCMD LIMIT 6554 6554
2061 EMFLMT 0 0
2062 OVC K1 32413 32413
2063 OVC K2 4431 4431
2064 TGALMLV 4 4
2065 OVC LIMIT 13201 13201
2066 ACC FB GAIN 0 0
2067 TCMD FILTER 0 0
2068-2073 0 0
2074 AALPH 8192 8192
2077-2083 0 0
2086 RATED CURRENT 2154 2154
2087-2098 0 0
2099 ONEPSL 400 400
2100 INPA1 0 0
2101 INPA2 0 0
2102 DBLIM 0 0
2103 ABVOF 0 0
2104 ABTSH 0 0
2105 TORQUE CONST. 1127 1503
2106-2109 0 0
2110 MGSTCM 1546 263
2111 TQLIM IN DEC. 4255 3065
2112 AMRDML 0 0
2113 HRV FILT 0 0
2127 NINTCT 2095 2712
2128 MFWKCE 3066 3354
2129 MFWKBL 1548 1038
2130-2132 SMOOTH CMP 0 0
2133 PHDLY1 4110 2567
2134 PHDLY2 12814 8967
2159 DGCSMM 0 0
2160 TRQCUP 0 0
2161 OVC STP 0 0
2162 OVC2 K1 32765 32765
2163 OVC2 K2 34 36
2164 OVC2 LIMIT 7387 7713
2165 MAX CURRENT 85 85
2302 TQLIM AT STOP 0 0
2304 ACCBSLM 0 0
2305 ACDCEBD 0 0
2310 DCIDBS 0 0
2316 LIMLIM 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
2.2 AC SERVO MOTOR βiS series HV
βiS2 βiS4 βiS8 βiS12 βiS22 βiS22 βiS30 βiS40
Motor model 4000HV 4000HV 3000HV 3000HV 2000HV 3000HV 2000HV 2000HV
Motor ID No. 251 264 267 270 278 314 473 475
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000100 00000000 00000000 00000000 00000000 00001000 00000010 00000010
2014 00000100 00000000 00000000 00000000 00000000 00001000 00000010 00000010
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001110 00001110 00001110 00001110 00001110 00001110 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 348 331 605 427 1446 1146 1650 1624
2041 CUR GAIN P -1676 -1560 -3028 -2301 -5822 -5267 -6565 -7197
2042 CUR GAIN 3 -1232 -1246 -1300 -1302 -1332 -1332 -2681 -1341
2043 VEL GAIN I 78 112 166 170 244 192 214 208
2044 VEL GAIN P -700 -1010 -1482 -1524 -2182 -1722 -1912 -1870
2045 VEL GAIN 3 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -1085 -751 5118 4978 3478 4406 3971 4057
2048 BLACC CMP 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510
2052 OVER SPEED 5600 5600 4200 4200 2700 4200 2800 2600
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0
2057 D-PHASE CUR -10250 -7694 -5140 -5140 -3612 -6174 -4647 -3375
2058 D-PHASE CUR -1000 -2800 -3200 -3500 -3000 -2843 -3115 -3862
2059 PPBAS 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 6554 7282 7282 7282 7282 5462 6554 6554
2061 EMFLMT 0 0 0 0 0 0 0 0
2062 OVC K1 32538 32299 32301 32435 32433 32548 32413 32413
2063 OVC K2 2879 5865 5842 4164 4185 2755 4431 4431
2064 TGALMLV 4 4 4 4 4 4 4 4
2065 OVC LIMIT 8560 17504 17435 12399 12462 8192 13201 13201
2066 ACC FB GAIN 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0
2074 AALPH 20480 20480 20480 20480 8192 8192 8192 8192
2077-2083 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1507 2155 2793 2356 2611 2069 2154 2154
2087-2098 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 119 146 225 420 689 869 1127 1503
2106-2109 0 0 0 0 0 0 0 0
2110 MGSTCM 1048 780 1807 1814 0 1289 1546 263
2111 TQLIM IN DEC. 11600 7790 7930 7930 2866 7268 4255 3065
2112 AMRDML 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0
2127 NINTCT 2345 1592 2885 2388 5149 3894 2095 2712
2128 MFWKCE 1000 500 1000 3000 3000 6000 3066 3354
2129 MFWKBL 3358 3339 1298 2056 562 2315 1548 1038
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0
2133 PHDLY1 7192 8972 3848 5138 3352 5647 4110 2567
2134 PHDLY2 8990 12816 8990 6430 8989 12820 12814 8967
2159 DGCSMM 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0
2162 OVC2 K1 32766 32765 32762 32764 32763 32765 32765 32765
2163 OVC2 K2 19 41 75 50 64 38 34 36
2164 OVC2 LIMIT 3617 7395 12424 8836 10854 6815 7387 7713
2165 MAX CURRENT 10 10 10 25 25 45 45 45
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
2.3 AC SERVO MOTOR βiSc series
βiSc2 βiSc2 βiSc4 βiSc4 βiSc8 βiSc8 βiSc12 βiSc12
Motor model 4000 4000 4000 4000 3000 3000 2000 2000
40A 40A 40A 40A
Motor specification 0061-Bxx7 0061-Bxx7 0063-Bxx7 0063-Bxx7 0075-Bxx7 0075-Bxx7 0077-Bxx7 0077-Bxx7
Motor ID No. 306 310 311 312 283 294 298 300
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000100 00010000 00000000 00001110 00000000 00001110 00000000 00001110
2014 00000100 00010000 00000000 00001110 00000000 00001110 00000000 00001110
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001110 00001110 00001110 00001110 00001110 00001110 00001110 00001110
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 360 720 400 800 650 1160 547 1094
2041 CUR GAIN P -1920 -3840 -1920 -3840 -3831 -5600 -3289 -6578
2042 CUR GAIN 3 -1237 -1237 -1253 -1253 -1299 -1299 -1305 -1305
2043 VEL GAIN I 78 39 112 56 164 82 230 115
2044 VEL GAIN P -698 -349 -1008 -504 -1476 -738 -2054 -1027
2045 VEL GAIN 3 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -1089 -2178 -753 -1506 5143 -1029 3695 7390
2048 BLACC CMP 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510
2052 OVER SPEED 5600 5600 5600 5600 4200 4200 2800 2800
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 -2570 0 0 0
2057 D-PHASE CUR -10250 -10245 -7694 -7687 -5140 -5131 -3884 -3862
2058 D-PHASE CUR -1000 -500 -2800 -1400 -3200 -1600 -4350 -2175
2059 PPBAS 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 6554 3277 7282 3641 7282 3641 7282 3641
2061 EMFLMT 0 0 0 0 0 0 0 0
2062 OVC K1 32652 32739 32532 32709 32381 32671 32323 32646
2063 OVC K2 1455 364 2945 738 4835 1214 5566 1525
2064 TGALMLV 4 4 4 4 4 4 4 4
2065 OVC LIMIT 4317 1079 8758 2189 14410 3603 16603 4511
2066 ACC FB GAIN 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0
2074 AALPH 16384 0 20480 0 16384 0 8192 0
2077-2083 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1529 764 2178 1089 2780 1390 3126 1563
2087-2098 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 119 238 146 292 226 452 315 630
2106-2109 0 0 0 0 0 0 0 0
2110 MGSTCM 1048 815 780 532 1807 1045 1 1282
2111 TQLIM IN DEC. 11600 11600 7790 7790 7930 7930 3940 3940
2112 AMRDML 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0
2127 NINTCT 1172 1172 796 796 1442 1442 1350 1350
2128 MFWKCE 2500 5000 3000 6000 3500 7000 4000 8000
2129 MFWKBL 3358 3358 3392 3392 1298 1298 280 280
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0
2133 PHDLY1 7192 7192 8992 8992 3858 3858 3614 3614
2134 PHDLY2 8990 8990 12864 9024 8990 8990 8980 4372
2159 DGCSMM 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0
2161 OVC STP 120 120 120 120 0 0 0 0
2162 OVC2 K1 32757 32765 32745 32762 32764 32767 32763 32767
2163 OVC2 K2 140 34 294 70 51 12 60 15
2164 OVC2 LIMIT 2665 666 5407 1352 8896 2224 10250 2785
2165 MAX CURRENT 25 45 25 45 25 45 25 45
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
3 Standard parameters for LINEAR MOTOR LiS series
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
3.1 LINEAR MOTOR LiS series [200V] (1/2)
Motor model A1/4 A1/4 A1/4 B1/4 B2/2 B2/4 B2/2 B2/4 B2/2 B2/4 B2/2
(200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V)
Motor ID No. 351 353 355 357 360 362 364 366 368 370 372
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000100 00000100 00000100 00000000 00000100 00000000 00000100
2211 00000000 00000000 00000000 00000000 00000000 00000000 00001000 00001000 00000000 00000000 00001000
2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 1968 1868 1594 1512 961 324 2834 4394 961 1401 848
2041 CUR GAIN P -7138 -6536 -6162 -11488 -5781 -4472 -10862 -21486 -5255 -10722 -5532
2042 CUR GAIN 3 -2618 -2618 -2618 -2647 -2667 -2660 -2696 -2689 -2660 -2660 -2696
2043 VEL GAIN I 16 9 13 19 14 16 10 10 13 15 8
2044 VEL GAIN P -217 -122 -179 -260 -194 -214 -131 -131 -169 -202 -103
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -8755 -9339 -6367 -4371 -5866 -5321 -8705 -8705 -6746 -5642 -11014
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP -6400 -6400 -6400 0 0 0 0 0 0 0 -7936
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 5826 6554 7282 7282 7282 7282 5462 5462 7282 7282 4551
2061 EMFLMT 120 120 120 120 120 120 120 120 120 120 120
2062 OVC K1 32720 32720 32721 32698 32711 32698 32707 32707 32711 32708 32707
2063 OVC K2 596 596 583 873 719 873 758 768 719 753 765
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 589 589 1326 2590 2131 2590 1199 1214 2131 2233 832
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH -24576 -8192 28672 0 0 0 20480 0 0 0 -24576
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 564 564 847 1184 1074 1184 805 810 1074 1184 671
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 68 137 137 227 502 455 1005 1005 1005 911 2010
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 793 792 786 0 0 0 0 0 0 0 0
2111 DETQLM 0 0 0 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 25 45 45 45 45 85 85 165 85 165 165
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
In the case of liquid cooling, modify the following parameters from the above table.
2062 POVC1 32578 32578 32582 32490 32539 32490 32526 32527 32539 32528 32524
2063 POVC2 2380 2380 2328 3481 2867 3481 3023 3018 2867 3003 3053
2065 POVCLMT 2357 2357 5303 10358 8523 10358 4794 4787 8523 8932 3329
2086 RATED CURRENT 1129 1129 1694 2368 2148 2368 1611 1610 2148 2368 1342
2161 OVCSTP - - - - - - - - - 140 -
2162 POVC21 - - - - - - - - - - -
2163 POVC22 - - - - - - - - - - -
2164 POVCLMT2 - - - - - - - - - - -
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model B2/4 B2/2 B2/4 C1/2 C2/2 C2/2 C2/4 C2/2 C2/3 C3/2 C3/2
(200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V)
Motor ID No. 374 376 378 380 384 388 390 392 394 396 400
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00001000 00000110 00001010 00000000 00000000 00000000 00000000 00001010 00000000 00000000 00000000
2014 00001000 00000110 00001010 00000000 00000000 00000000 00000000 00001010 00000000 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000000 00000100 00000100 00000100 00000100
2211 00001000 00000000 00000000 00001000 00001000 00001000 00001000 00000000 00000000 00001000 00001000
2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 946 1240 1483 1346 587 431 3736 1704 478 158 2182
2041 CUR GAIN P -6400 -7877 -7099 -6448 -3839 -3377 -18246 -13440 -3379 -1761 -8540
2042 CUR GAIN 3 -1331 -2660 -2660 -2695 -2696 -2695 -2693 -2663 -2657 -2695 -2696
2043 VEL GAIN I 8 12 10 9 8 10 9 7 10 10 7
2044 VEL GAIN P -101 -158 -141 -126 -110 -136 -121 -87 -128 -141 -99
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -11240 -7199 -8099 -9048 -10377 -8363 -9409 -13022 -8861 -8077 -11497
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP -7680 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 4046 5917 4855 5462 6372 7282 6877 4855 7282 7282 6887
2061 EMFLMT 120 120 120 120 120 120 120 120 120 120 120
2062 OVC K1 32687 32707 32696 32708 32729 32723 32729 32729 32732 32722 32711
2063 OVC K2 1010 758 895 749 489 560 492 483 452 582 709
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 799 1199 1151 1184 1112 1661 1311 621 1340 1719 981
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 0 0 0 -16384 -24576 0 0 0 -24576 20480
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 658 805 789 801 776 948 842 579 852 964 729
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 2051 2010 2051 741 2087 2087 2348 4656 3168 1865 4197
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 0 0 0 0 0 0 0 0 0 0 0
2111 DETQLM 0 0 0 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 365 165 365 85 165 165 365 365 365 165 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
2062 POVC1 32446 32526 32482 32529 32612 32589 32598 32558 32572 32583 32542
2063 POVC2 4026 3023 3570 2987 1953 2236 2119 2623 2455 2314 2829
2065 POVCLMT 3197 4794 4604 4738 4448 6644 5246 3378 7296 6875 3925
2086 RATED CURRENT 1316 1611 1579 1602 1552 1897 1685 1352 1988 1929 1458
2161 OVCSTP - - - - - - - - 140 - -
2162 POVC21 - - - - - - - - - - -
2163 POVC22 - - - - - - - - - - -
2164 POVCLMT2 - - - - - - - - - - -
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model B1/4 B2/2 B2/2HV B2/2 B2/2HV B2/2 B2/2HV B2/2 B2/2 C1/2 C2/2HV
(400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V)
Motor ID No. 358 361 363 365 367 369 371 373 377 381 383
PRM NO SERVO PRM.
2003 00001000 00000000 00001000 00001000 00000000 00001000 00001000 00001000 00000000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000110 00000000 00000000 00001000 00000010 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000110 00000000 00000000 00001000 00000010 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000000
2211 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2300 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 409 602 2590 802 1469 766 1742 1123 834 636 1453
2041 CUR GAIN P -2068 -3127 -6505 -4726 -9936 -4195 -6205 -6625 -4701 -3246 -13899
2042 CUR GAIN 3 -2689 -1330 -2697 -2696 -1330 -2696 -2697 -2696 -1330 -2695 -1321
2043 VEL GAIN I 19 14 11 10 7 13 9 7 9 9 8
2044 VEL GAIN P -260 -194 -149 -131 -96 -169 -117 -92 -128 -126 -108
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -4371 -5866 -7658 -8705 -11870 -6746 -9690 -12391 -8929 -9048 -10496
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 -7680 0 0 0 -9216 0 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 6554 5462 4369 7282 5462 4046 5259 5462 6372
2061 EMFLMT 120 120 120 120 120 120 120 120 120 120 120
2062 OVC K1 32698 32711 32714 32707 32749 32711 32714 32709 32709 32708 32729
2063 OVC K2 873 719 681 758 232 719 680 739 737 749 489
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 2590 2131 1549 1199 688 2131 1075 858 947 1184 1112
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 0 20480 20480 0 20480 0 20480 0 20480 0 0
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1184 1074 915 805 610 1074 763 671 716 801 776
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 227 502 884 1005 1768 1005 1768 2261 2261 741 2111
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 0 0 0 0 0 0 0 0 0 0 0
2111 DETQLM 0 0 0 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 45 45 45 85 85 85 85 185 185 85 85
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
2062 POVC1 32490 32539 32551 32526 32521 32539 32551 32532 32533 32529 32614
2063 POVC2 3481 2867 2718 3023 3085 2867 2713 2949 2940 2987 1925
2065 POVCLMT 10358 8523 6194 4794 2753 8523 4301 2631 3788 4738 4383
2086 RATED CURRENT 2368 2148 1831 1611 1221 2148 1526 1193 1432 1602 1540
2161 OVCSTP - - - - - - - - 140 - -
2162 POVC21 - - - - - - - - - - -
2163 POVC22 - - - - - - - - - - -
2164 POVCLMT2 - - - - - - - - - - -
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
LiS9000 LiS11000 LiS11000 LiS15000 LiS10000 LiS10000 LiS17000 LiS17000
Motor model C2/2 C2/2HV C2/2 C2/3HV C3/2HV C3/2 C3/2HV C3/2
(400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V)
Motor specification 0454-B110 0455-B010 0455-B110 0456-B010 0457-B010 0457-B110 0459-B010 0459-B110
Motor ID No. 385 387 389 391 395 397 399 401
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000100 00000100 00000100 00000100 00000100 00000100 00000000 00000100
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000100 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000100 00000000 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000000 00000100 00000000 00000100
2211 00001000 00001000 00001000 00001000 00001000 00000000 00000000 00000000
2300 10000000 10000000 10000000 10000000 10000000 10000000 00000000 10000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 910 605 702 989 3010 839 709 253
2041 CUR GAIN P -4971 -3361 -4479 -6312 -6519 -4103 -3688 -3693
2042 CUR GAIN 3 -2696 -2694 -2695 -2695 -2695 -2695 -1330 -2696
2043 VEL GAIN I 7 10 9 10 10 9 7 7
2044 VEL GAIN P -98 -136 -121 -131 -129 -125 -99 -99
2045 VEL GAIN 3 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 -11674 -8363 -9409 -8681 -8849 -9086 -11497 -11497
2048 BLACC CMP 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 -12032 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 5663 7282 6877 7282 7282 6877 5259 6877
2061 EMFLMT 120 120 120 120 120 120 120 120
2062 OVC K1 32728 32723 32730 32730 32722 32720 32711 32711
2063 OVC K2 494 560 474 471 576 597 709 709
2064 TGALMLV 4 4 4 4 4 4 4 4
2065 OVC LIMIT 879 1661 1312 1396 1707 1358 981 981
2066 ACC FB GAIN 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0
2074 AALPH 0 -24576 0 0 -4096 20480 -24576 20480
2077-2083 0 0 0 0 0 0 0 0
2086 RATED CURRENT 689 948 843 869 961 857 729 729
2087-2098 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 2348 2087 2348 3104 2043 2098 4197 4197
2106-2109 0 0 0 0 0 0 0 0
2110 MGSTCM 0 0 0 0 0 0 0 0
2111 DETQLM 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0
2165 MAX CURRENT 185 85 185 185 85 185 185 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0
2062 POVC1 32610 32589 32616 32563 32584 32577 32542 32542
2063 POVC2 1972 2236 1894 2557 2298 2384 2829 2829
2065 POVCLMT 3514 6644 5250 7601 6828 5432 3925 3925
2086 RATED CURRENT 1379 1897 1686 2029 1923 1715 1458 1458
2161 OVCSTP - - 140 140 - 140 - -
2162 POVC21 - - - - - - - -
2163 POVC22 - - - - - - - -
2164 POVCLMT2 - - - - - - - -
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
4 Standard parameters for SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
4.1 SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series [200V] (1/3)
Motor model 250 600 400 300 300 600 300 250 250 200 150
(200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V)
Motor ID No. 419 421 423 425 427 429 431 433 435 437 439
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00001000 00000000 00001000 00001000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00001000 00000000 00001000 00001000 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2300 10000110 10000110 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 494 621 344 156 313 571 478 738 517 640 637
2041 CUR GAIN P -1949 -2202 -2368 -1045 -2146 -4138 -3338 -2500 -3361 -4779 -4762
2042 CUR GAIN 3 -2943 -2946 -2491 -2448 -2485 -2573 -2515 -2996 -2408 -2619 -2620
2043 VEL GAIN I 415 157 242 420 326 240 264 386 430 839 1760
2044 VEL GAIN P -3713 -1410 -2164 -3763 -2919 -2146 -2361 -3461 -3850 -7513 -15770
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 2271 5982 3897 2241 2889 3931 3572 2437 2190 1122 535
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 5352 7282 5648 5648 7282 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32743 32689 32683 32682 32682 32679 32705 32713 32677 32682 32682
2063 OVC K2 308 988 1069 1069 1069 1111 782 690 1113 1069 1069
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 903 2826 3172 3173 3173 1710 2322 1200 1940 3173 3173
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 20480 0 0 0 0 0 0 0 0 0
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 753 1237 1310 1310 1310 963 1121 868 1028 1310 1310
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 8080 448 1167 1510 3570 4857 6020 16519 21246 20598 25635
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 1281 1793 0 0 0 0 0 0 0 0 0
2111 DETQLM 1535 8568 0 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 16776 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 14 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 120 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 85 25 45 85 85 165 85 165 165 165 165
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
2062 POVC1 32646 32523 32427 32427 32427 32360 32518 32529 32352 32427 32427
2063 POVC2 1528 3069 4258 4260 4260 5100 3121 2989 5196 4259 4259
2065 POVCLMT 4290 8170 12689 12694 12694 6848 9287 4801 7743 12692 12693
2086 RATED CURRENT 1641 2104 2621 2621 2621 1926 2242 1737 2033 2621 2621
2161 OVCSTP - - - - - 102 - 107 107 162 162
2162 POVC21 - - - - - - - - - - -
2163 POVC22 - - - - - - - - - - -
2164 POVCLMT2 - - - - - - - - - - -
Remarks *5 *5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
DiS3000 DiS85 DiS110 DiS260 DiS22
Motor model 150 1000 1000 1000 1500
(200V) (200V) (200V) (200V) (200V)
Motor specification 0487-B40x 0483-B22x 0484-B12x 0484-B32x 0482-B12x
Motor ID No. 441 443 445 447 449
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000001 00000001 00000001 00000001
2014 00000000 00000000 00000000 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000100
2211 00000000 00001000 00001000 00001000 00001010
2300 10000100 10000110 10000110 10000110 10000110
2301 10000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 817 480 301 290 562
2041 CUR GAIN P -6084 -1395 -1001 -916 -1568
2042 CUR GAIN 3 -2616 -3002 -3024 -3016 -2948
2043 VEL GAIN I 1635 220 292 243 202
2044 VEL GAIN P -14643 -1971 -2614 -2178 -1811
2045 VEL GAIN 3 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 576 4278 3227 3871 4657
2048 BLACC CMP 0 0 0 0 0
2049 DPFMX 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0
2057 D-PHASE CUR 0 -12846 -20535 -10266 -17944
2058 D-PHASE CUR 0 -2731 -1183 -1821 -2257
2059 PPBAS 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282
2061 EMFLMT 0 0 0 0 0
2062 OVC K1 32682 32346 32434 32580 32439
2063 OVC K2 1069 5276 4174 2354 4109
2064 TGALMLV 4 4 4 4 4
2065 OVC LIMIT 3173 15735 12437 6423 10559
2066 ACC FB GAIN 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0
2068-2073 0 0 0 0 0
2074 AALPH 0 20480 8192 8192 0
2077-2083 0 0 0 0 0
2086 RATED CURRENT 1310 2919 2595 1865 2576
2087-2098 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400
2100 INPA1 0 0 0 0 0
2101 INPA2 0 0 0 0 0
2102 DBLIM 0 0 0 0 0
2103 ABVOF 0 0 0 0 0
2104 ABTSH 0 0 0 0 0
2105 TORQUE CONST. 3667 1281 2175 4784 348
2106-2109 0 0 0 0 0
2110 MGSTCM 0 2313 1027 1537 2049
2111 DETQLM 0 11647 14212 11620 16720
2112 AMRDML 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0
2127 NINTCT 0 0 0 0 0
2128 MFWKCE 0 10500 15000 9800 6500
2129 MFWKBL 0 278 533 287 792
2130-2132 SMOOTH CMP 0 0 0 0 0
2133 PHDLY1 0 0 0 0 30735
2134 PHDLY2 0 0 0 0 10270
2159 DGCSMM 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0
2161 OVC STP 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0
2165 MAX CURRENT 165 45 85 165 25
2302 TQLIM AT STOP 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0
2062 POVC1 32427 - - - -
2063 POVC2 4259 - - - -
2065 POVCLMT 12693 - - - -
2086 RATED CURRENT 2621 - - - -
2161 OVCSTP 162 - - - -
2162 POVC21 - - - - -
2163 POVC22 - - - - -
2164 POVCLMT2 - - - - -
Remarks *5 *5 *5 *5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model 1000 400 300 300 300 250 250 200 100 100 150
(200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V) (200V)
Motor ID No. 551 553 555 557 559 561 563 565 567 569 571
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000010 00000010 00000010 00000010 00000010 00000010 00001010 00001010 00001010 00001010
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00001000 00000110 00000110 00000110 00000000 00000000 00000000 00000000 00000000 00000100
2014 00000000 00001000 00000110 00000110 00000110 00000000 00000000 00000000 00000000 00000000 00000100
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00011000 00001000 00001000 00001000 00011000 00001000 00001000 00011000 00011000 00011000 00001000
2300 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10010100 10000000 10000000 10000000
2040 CUR GAIN I 309 538 296 379 451 294 321 434 490 637 448
2041 CUR GAIN P -1713 -3794 -2764 -3215 -3966 -2458 -2569 -2352 -3676 -5353 -3457
2042 CUR GAIN 3 -3067 -3102 -3117 -3128 -3135 -3129 -3138 -3173 -3176 -3177 -3177
2043 VEL GAIN I 69 86 180 149 141 334 297 558 760 689 620
2044 VEL GAIN P -618 -772 -1614 -1331 -1261 -2996 -2664 -4997 -6812 -6171 -5554
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 13637 10929 5224 6336 6686 2815 3165 1688 1238 1367 1518
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 720 240 180 180 180 150 150 120 60 60 90
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 -1038 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 -489 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 5462 6190 6190 6190 7282 7282 7282 7282 7282 6473
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32675 32675 32684 32714 32721 32707 32723 32677 32682 32709 32707
2063 OVC K2 1160 1160 1056 679 590 761 567 1135 1078 740 763
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 3300 1856 2178 1419 1237 2196 1646 3231 3076 2136 1739
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH -20480 -32768 -24576 -20480 -4096 -4096 20480 -20480 28672 24576 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1440 845 1005 944 881 1175 1062 1421 1390 1176 1045
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 612 2865 3521 7830 11266 10329 20150 3349 5516 8086 8984
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 2305 1793 1793 1793 1793 1793 2049 2049 2049 2049 2049
2111 DETQLM 8854 6174 5173 5173 2625 3890 3890 2680 1184 1244 2218
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 16000 4000 0 4000 6000 7000 5000 10000 5000 15000 10000
2129 MFWKBL 277 6158 0 5134 2581 3861 3861 2588 1042 1042 2069
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 25 45 45 85 85 85 165 165 165 165 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 72 0 0 0 36 0 0 24 12 12 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
In the case of liquid cooling, modify the following parameters from the above table. The value put in () is used when the motor is driven by servo amplifier aiSV160/160.
2062 POVC1 32401 32275 32449 32391 32368 32487 32454(32465) 32344(32465) 32384(32453) 32366(32465) 32369
2063 POVC2 4589 6169 3986 4717 5004 3513 3923( 3783) 5300( 3782) 4796( 3942) 5019( 3782) 4992
2065 POVCLMT 11603 8321 7432 8580 9014 9212 10144( 9830) 13083( 9827) 12041(10187) 12508( 9827) 9838
2086 RATED CURRENT 2700 2294 2159 2201 2201 2201 2606( 2259) 2606( 2259) 2606( 2259) 2606( 2259) 2492
2161 OVCSTP 125 127 120 120 123 110 110 110 112 110 110
2162 POVC21 32601 32581 32629 32599 32594 32623 32596(32600) 32686(32700) 32686(32700) 32713(32705) 32705
2163 POVC22 2091 2337 1735 2118 2172 1813 2156( 2103) 1027( 852) 1024( 853) 687( 789) 792
2164 POVCLMT2 8308 5958 5321 6143 6454 6595 7263( 7038) 9367( 7036) 8621( 7294) 8955( 7036) 7044
Remarks *2,*5 *5 *5 *5 *2,*5 *5 *5 *2,*3,*5 *2,*3*,5 *2,*3,*5 *3,*5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model 250 600 400 300 300 600 300 250 250 200 150
(400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V)
Motor ID No. 420 422 424 426 428 430 432 434 436 438 440
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00001000 00000000 00001000 00001000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00001000 00000000 00001000 00001000 00000000 00000000
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2300 10000110 10000110 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100 10000100
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2040 CUR GAIN I 494 374 172 78 157 321 239 496 291 360 359
2041 CUR GAIN P -1352 -1042 -1184 -523 -1073 -2327 -1669 -1588 -1891 -2688 -2679
2042 CUR GAIN 3 -2943 -2946 -2491 -2448 -2485 -2573 -2515 -2996 -2408 -2619 -2620
2043 VEL GAIN I 415 157 242 420 326 213 264 343 382 746 1565
2044 VEL GAIN P -3713 -1410 -2164 -3763 -2919 -1907 -2361 -3076 -3422 -6678 -14017
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 2271 5982 3897 2241 2889 4422 3572 2742 2464 1263 602
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 0 0 0 0 0 0 0 0 0 0 0
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 0 0 0 0 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 0 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 7282 7282 7282 7282 4758 7282 5020 5020 6473 7282
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32743 32689 32683 32682 32682 32679 32705 32713 32678 32700 32682
2063 OVC K2 308 988 1069 1069 1069 1111 782 690 1130 845 1069
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 903 2826 3172 3173 3173 1351 2322 948 1529 2507 3173
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH 20480 0 0 0 0 0 0 0 0 0 0
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 753 1237 1310 1310 1310 856 1121 772 914 1165 1310
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 8080 448 1167 1510 3570 5464 6020 18584 23902 23173 28839
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 1281 1793 0 0 0 0 0 0 0 0 0
2111 DETQLM 0 25660 0 0 0 0 0 0 0 0 0
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 120 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 85 25 45 85 85 185 85 185 185 185 185
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 0 0 0 0 0 0 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
2062 POVC1 32646 32523 32427 32427 32427 32360 32518 32529 32352 32498 32427
2063 POVC2 1528 3069 4258 4260 4260 5095 3121 2989 5196 3369 4259
2065 POVCLMT 4290 8170 12689 12694 12694 5406 9287 3793 6118 10029 12693
2086 RATED CURRENT 1641 2104 2621 2621 2621 1712 2242 1544 1807 2330 2621
2161 OVCSTP - - - - - - - - - 109 122
2162 POVC21 - - - - - - - - - - -
2163 POVC22 - - - - - - - - - - -
2164 POVCLMT2 - - - - - - - - - - -
Remarks *5 *5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
DiS3000
Motor model 150
(400V)
Motor specification 0487-B40x
Motor ID No. 442
PRM NO SERVO PRM.
2003 00001000
2004 00000011
2005 00000000
2006 00000000
2007 00000000
2008 00000000
2009 00000000
2010 00000000
2011 00000000
2012 00000000
2013 00000000
2014 00000000
2210 00000100
2211 00000000
2300 10000100
2301 10000000
2040 CUR GAIN I 459
2041 CUR GAIN P -3422
2042 CUR GAIN 3 -2616
2043 VEL GAIN I 1453
2044 VEL GAIN P -13016
2045 VEL GAIN 3 0
2046 VEL GAIN 4 -8235
2048 BLACC CMP 0
2049 DPFMX 0
2052 OVER SPEED 0
2056 EMFCMP 0
2057 D-PHASE CUR 0
2058 D-PHASE CUR 0
2059 PPBAS 0
2061 EMFLMT 0
2062 OVC K1 32682
2063 OVC K2 1069
2064 TGALMLV 4
2065 OVC LIMIT 3173
2066 ACC FB GAIN 0
2067 TCMD FILTER 0
2068-2073 0
2074 AALPH 0
2077-2083 0
2087-2098 0
2099 ONEPSL 400
2100 INPA1 0
2101 INPA2 0
2102 DBLIM 0
2103 ABVOF 0
2104 ABTSH 0
2106-2109 0
2110 MGSTCM 0
2111 DETQLM 0
2112 AMRDML 0
2113 HRV FILT 0
2127 NINTCT 0
2128 MFWKCE 0
2129 MFWKBL 0
2133 PHDLY1 0
2134 PHDLY2 0
2159 DGCSMM 0
2160 TRQCUP 0
2161 OVC STP 0
2162 OVC2 K1 0
2163 OVC2 K2 0
2164 OVC2 LIMIT 0
2304 ACCBSLM 0
2305 ACDCEBD 0
2310 DCIDBS 0
2316 LIMLIM 0
2062 POVC1 32427
2063 POVC2 4259
2065 POVCLMT 12693
2161 OVCSTP 122
2162 POVC21 -
2163 POVC22 -
2164 POVCLMT2 -
Remarks
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Motor model 1000 400 300 300 300 250 250 200 100 100 150
(400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V) (400V)
Motor ID No. 552 554 556 558 560 562 564 566 568 570 572
PRM NO SERVO PRM.
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000010 00000010 00000010 00000010 00001010 00001010 00000010
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00001000 00000110 00000110 00000110 00000000 00000100 00000100 00000100 00000100 00000100
2014 00000000 00001000 00000110 00000110 00000110 00000000 00000100 00000100 00000100 00000100 00000100
2210 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100 00000100
2211 00001000 00001000 00001000 00001000 00011000 00001000 00001000 00001000 00001000 00011000 00001000
2300 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110 10000110
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10010100 10000000 10000000 10000000
2040 CUR GAIN I 154 269 148 189 226 158 181 244 276 358 224
2041 CUR GAIN P -857 -1897 -1382 -1607 -1983 -1150 -1445 -1323 -2068 -3011 -1729
2042 CUR GAIN 3 -3067 -3102 -3117 -3128 -3135 -3129 -3138 -3173 -3176 -3177 -3177
2043 VEL GAIN I 69 86 180 149 141 334 264 496 676 612 620
2044 VEL GAIN P -618 -772 -1614 -1331 -1261 -2996 -2368 -4442 -6055 -5485 -5554
2045 VEL GAIN 3 0 0 0 0 0 0 0 0 0 0 0
2046 VEL GAIN 4 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
2047 OBSERVER POA1 13637 10929 5224 6336 6686 2815 3561 1899 1393 1537 1518
2048 BLACC CMP 0 0 0 0 0 0 0 0 0 0 0
2049 DPFMX 0 0 0 0 0 0 0 0 0 0 0
2050 OBSERVER POK1 956 956 956 956 956 956 956 956 956 956 956
2051 OBSERVER POK2 510 510 510 510 510 510 510 510 510 510 510
2052 OVER SPEED 1200 480 360 360 360 300 300 240 120 120 180
2053 DB-CMP PPMAX 21 21 21 21 21 21 21 21 21 21 21
2054 DB-CMP PDDP 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894 1894
2055 DB-CMP PHYST 319 319 319 319 319 319 319 319 319 319 319
2056 EMFCMP 0 0 0 0 0 0 -11264 -11264 -11264 -11264 0
2057 D-PHASE CUR 0 0 0 0 0 0 0 0 0 -2054 0
2058 D-PHASE CUR 0 0 0 0 0 0 0 0 0 -430 0
2059 PPBAS 0 0 0 0 0 0 0 0 0 0 0
2060 TCMD LIMIT 7282 5462 6190 6190 6190 7282 6473 6473 6473 6473 6473
2061 EMFLMT 0 0 0 0 0 0 0 0 0 0 0
2062 OVC K1 32675 32675 32684 32714 32721 32707 32723 32677 32682 32709 32707
2063 OVC K2 1160 1160 1056 679 590 761 567 1135 1078 740 763
2064 TGALMLV 4 4 4 4 4 4 4 4 4 4 4
2065 OVC LIMIT 3300 1856 2178 1419 1237 2196 1301 2553 2430 1688 1739
2066 ACC FB GAIN 0 0 0 0 0 0 0 0 0 0 0
2067 TCMD FILTER 0 0 0 0 0 0 0 0 0 0 0
2068-2073 0 0 0 0 0 0 0 0 0 0 0
2074 AALPH -20480 -32768 -24576 -20480 -4096 -8192 20480 -20480 28672 24576 12288
2077-2083 0 0 0 0 0 0 0 0 0 0 0
2086 RATED CURRENT 1440 845 1005 944 881 1175 944 1266 1235 1045 1045
2087-2098 0 0 0 0 0 0 0 0 0 0 0
2099 ONEPSL 400 400 400 400 400 400 400 400 400 400 400
2100 INPA1 0 0 0 0 0 0 0 0 0 0 0
2101 INPA2 0 0 0 0 0 0 0 0 0 0 0
2102 DBLIM 0 0 0 0 0 0 0 0 0 0 0
2103 ABVOF 0 0 0 0 0 0 0 0 0 0 0
2104 ABTSH 0 0 0 0 0 0 0 0 0 0 0
2105 TORQUE CONST. 612 2865 3521 7830 11266 10329 22669 3768 6206 9097 8984
2106-2109 0 0 0 0 0 0 0 0 0 0 0
2110 MGSTCM 2049 1793 1793 1793 1793 1793 2049 2305 2049 2049 2049
2111 DETQLM 0 0 0 0 7710 12900 11311 6229 3212 2161 4727
2112 AMRDML 0 0 0 0 0 0 0 0 0 0 0
2113 HRV FILT 0 0 0 0 0 0 0 0 0 0 0
2127 NINTCT 0 0 0 0 0 0 0 0 0 0 0
2128 MFWKCE 0 0 0 0 0 0 0 0 0 0 0
2129 MFWKBL 0 0 0 0 0 0 0 0 0 0 0
2130-2132 SMOOTH CMP 0 0 0 0 0 0 0 0 0 0 0
2133 PHDLY1 0 0 0 0 0 0 0 0 0 0 0
2134 PHDLY2 0 0 0 0 0 0 0 0 0 0 0
2159 DGCSMM 0 0 0 0 0 0 0 0 0 0 0
2160 TRQCUP 0 0 0 0 0 0 0 0 0 0 0
2161 OVC STP 0 0 0 0 0 0 0 0 0 0 0
2162 OVC2 K1 0 0 0 0 0 0 0 0 0 0 0
2163 OVC2 K2 0 0 0 0 0 0 0 0 0 0 0
2164 OVC2 LIMIT 0 0 0 0 0 0 0 0 0 0 0
2165 MAX CURRENT 25 45 45 85 85 85 185 185 185 185 365
2302 TQLIM AT STOP 0 0 0 0 0 0 0 0 0 0 0
2304 ACCBSLM 0 0 0 0 0 0 0 0 0 0 0
2305 ACDCEBD 0 0 0 0 72 0 0 0 0 24 0
2310 DCIDBS 0 0 0 0 0 0 0 0 0 0 0
2316 LIMLIM 0 0 0 0 0 0 0 0 0 0 0
2062 POVC1 32401 32275 32449 32391 32368 32487 32454 32286 32384 32366 32369
2063 POVC2 4589 6169 3986 4717 5004 3513 3923 6024 4796 5019 4992
2065 POVCLMT 11603 8321 7432 8580 9014 9212 8015 11469 9514 9883 9838
2086 RATED CURRENT 2595 2108 2108 2108 2108 2109 2317 2760 2445 2497 2492
2161 OVCSTP 125 127 120 120 123 110 110 110 112 110 110
2162 POVC21 32601 32581 32629 32599 32594 32623 32596 32686 32686 32713 32705
2163 POVC22 2091 2337 1735 2118 2172 1813 2156 1029 1024 687 792
2164 POVCLMT2 8308 5958 5321 6143 6454 6595 5738 8212 6812 7076 7044
Remarks *5 *5 *5 *5 *2,*5 *5 *5 *5 *3,*5 *2,*3,*5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
DiS5000
Motor model 50
(400V)
Motor specification 0488-B400
Motor ID No. 573
PRM NO SERVO PRM.
2003 00001000
2004 00000011
2005 00000000
2006 00001010
2007 00000000
2008 00000000
2009 00000000
2010 00000000
2011 00000000
2012 00000000
2013 00000000
2014 00000000
2210 00000100
2211 00011000
2300 10000110
2301 10010100
2040 CUR GAIN I 417
2041 CUR GAIN P -3875
2042 CUR GAIN 3 -3181
2043 VEL GAIN I 1096
2044 VEL GAIN P -9817
2045 VEL GAIN 3 0
2046 VEL GAIN 4 -8235
2048 BLACC CMP 0
2049 DPFMX 0
2052 OVER SPEED 60
2056 EMFCMP 0
2059 PPBAS 0
2061 EMFLMT 0
2062 OVC K1 32731
2063 OVC K2 459
2064 TGALMLV 4
2065 OVC LIMIT 1337
2066 ACC FB GAIN 0
2067 TCMD FILTER 0
2068-2073 0
2074 AALPH 24576
2077-2083 0
2087-2098 0
2099 ONEPSL 400
2100 INPA1 0
2101 INPA2 0
2102 DBLIM 0
2103 ABVOF 0
2104 ABTSH 0
2106-2109 0
2110 MGSTCM 1793
2111 DETQLM 767
2112 AMRDML 0
2113 HRV FILT 0
2127 NINTCT 0
2128 MFWKCE 16000
2129 MFWKBL 540
2133 PHDLY1 0
2134 PHDLY2 0
2159 DGCSMM 0
2160 TRQCUP 0
2161 OVC STP 0
2162 OVC2 K1 0
2163 OVC2 K2 0
2164 OVC2 LIMIT 0
2304 ACCBSLM 0
2305 ACDCEBD 12
2310 DCIDBS 0
2316 LIMLIM 0
2062 POVC1 32559
2063 POVC2 2617
2065 POVCLMT 7076
2161 OVCSTP 110
2162 POVC21 32722
2163 POVC22 569
2164 POVCLMT2 5066
Remarks *2,*3,*5
TITLE
DRAW. No. CUST.
B-65270EN/07-044
SHEET
Notice of the update of Digital Servo Software for Series 16i /18i /21i etc. ( 90B1)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
Notice of the update of Digital Servo Software

TITLE
for Series 16i /18i /21i etc. (90B1)

DRAW. No. CUST.
B-65270EN/07-045
SHEET
Notice of the update of Digital Servo Software for Series16i/18i/21i etc. ( 90B1)
1. Update Edition

Standard parameter table has been changed. Please refer to the Technical Report
B-65270EN/07-044（TMS11/091）“Notice of the latest version of Standard Parameter
Table” for the details.
Notice of the update of Digital Servo Software

TITLE
for Series 16i /18i /21i etc. (90B1)

DRAW. No. CUST.
B-65270EN/07-045
SHEET
Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i-A (90E1)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE

for Series 30i/ 31i/ 32i -A (90E1)
DRAW. No. CUST.

Ed. Date Design Description SHEET 1/3

1. Update Edition
90E1 10.0
Standard parameter table has been changed. Please refer to the Technical Report TMS11/091
（B-65270EN/07-044）“Notice of the latest version of Standard Parameter Table” for the details.
3. Attached
TITLE

DRAW. No. CUST.


(1) αiS series

αiF 30/3000HV 0255 304
αiF 40/3000HV 0259 309
αiF 40/3000HV Fan 0259 479

αiS 50/3000HV Fan 0276 326
αiS 50/3000HV 0276 327
αiS 60/3000HV Fan 0279 329
(2) βiS series

-Standard parameters of βiS12/3000, βiS22/2000 driven by 80A amplifier have been added.
Motor Model Motor Specification Motor ID No. Driven Amplifier
βiS 12/3000 272（exist） 40A

0078
477 80A
βiS 22/2000 274(exist) 40A
0085
478 80A
(3) DiS series

- Parameter (N2006#3) of following motors has been changed to 1.
DiS1000/200 0496-B300 565 200V
DiS1500/100 0497-B300 567 200V
DiS2000/100 0497-B400 569 200V
DiS2000/150 0497-B490 571 200V
DiS1500/100 0497-B300 568 400V
DiS2000/100 0497-B400 570 400V
DiS5000/50 0488-B400 573 400V
TITLE

DRAW. No. CUST.


Notice of the Update of Digital Servo Software for Series 30i/ 31i/ 32i-A (90E0 )

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Basic Function
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE

DRAW. No. CUST.


1. Update Edition
90E0 33.0
Standard parameter table has been changed. Please refer to the Technical Report TMS11/091
（B-65270EN/07-044）“Notice of the latest version of Standard Parameter Table” for the details.
3. Attached
TITLE

DRAW. No. CUST.


(1) αiS series

αiF 30/3000 HV 0255 304
αiF 40/3000HV 0259 309
αiF 40/3000HV Fan 0259 479

αiS 50/3000HV Fan 0276 326
αiS 50/3000HV 0276 327
αiS 60/3000HV Fan 0279 329
(2) βiS series

-Standard parameters of βiS12/3000, βiS22/2000 driven by 80A amplifier have been added.
βiS 12/3000 272（exist） 40A

0078
477 80A
βiS 22/2000 274(exist) 40A
0085
478 80A
(3) DiS series

- Parameter (N2006#3) of following motors has been changed to 1.
DiS1000/200 0496-B300 565 200V
DiS1500/100 0497-B300 567 200V
DiS2000/100 0497-B400 569 200V
DiS2000/150 0497-B490 571 200V
DiS1500/100 0497-B300 568 400V
DiS2000/100 0497-B400 570 400V
DiS5000/50 0488-B400 573 400V
TITLE

DRAW. No. CUST.


Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate –D (90C8, 90E8)

PARAMETER MANUAL
New, Add Applicable
Correct, Del Date
Basic Function - Speed Arrival Signal and Zero-Speed Detecting Signal Add 2012.08
- Changes of Standard Parameter Table Add 2012.08
Optional
Function
Unit
Maintenance
Parts
Notice
Correction
Another
TITLE
for Series 0i-D / 0i Mate-D ( 90C8,90E8)
DRAW. No. CUST.
B-65270EN/07-049
Ed. Date Design Description
SHEET 1/6
Notice of the Update of Digital Servo Software for Series 0i -D / 0i Mate –D (90C8, 90E8)
1. Update Edition
2.
90C8 04.0 Series 0i-D, 0i Mate-D
90E8 04.0 Series 0i-D ( Series 0i-TD, 2Path System )
- Speed Arrival Signal and Zero-Speed Detecting Signal
Speed arrival signal (SVSAR) and Zero-speed detecting signal (SVSST) that are used in spindle
control by servo motor have been supported.
Please refer technical report B65270JA/07-038/02 “Speed Arrival Signal and Zero-Speed Detecting
Signal” for detail.
- Changes of Standard parameter Table

3. Atteched
- Attached 1 Changes of Standard parameter Table
TITLE
DRAW. No. CUST.
B-65270EN/07-049
SHEET 2/6
Motor Model in the following table is added or changed.
(Please refer to attached tables about the detail of standard parameters.)
Motor Model Motor Specification Motor ID Number Added/Changed
αiF 4/5000 0223 273 Changed
αiF 4/5000HV 0225 275 Changed
αiF 8/4000 0228 492 Added
αiF 8/4000HV 0220 493 Added
αiF 12/4000 0243 293 Changed
αiF 22/4000 0248 494 Added
αiF 22/4000HV 0240 495 Added
αiF 30/4000 0253 303 Changed
αiS 3000/2000HV 0092 460 Changed
βiF 4/3000 0051 483 Added
βiF 4/3000 40A 0051 484 Added
βiF 8/2000 0052 485 Added
βiF 8/2000 40A 0052 486 Added
βiF 12/2000 0053 487 Added
βiF 12/2000 40A 0053 488 Added
βiF 22/2000 0054 489 Added
βiF 22/2000 80A 0054 490 Added
βiF 30/1500 0055 491 Added
LiS15000C2/2(400V) 0456-B110 393 Added
TITLE
DRAW. No. CUST.
B-65270EN/07-049
SHEET 3/6
Table1
Motor Model αiF4 αiF4 αiF12 αiF12 αiF30 αiF30 LiS15000 αiS3000
5000 5000HV 4000 4000HV 4000 4000HV C2/2 2000HV
(400V)
Motor Specification 0223 0225 0243 0245 0253 0255 0456-B110 0092
Motor ID Number 273 275 293 295 303 304 393 460
Symbol FS0i-D
2003 00001000 00001000 00001000 00001000 00001000 00001000 00000000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 01000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000100 00000000
2011 00100000 00000000 00100000 00100000 00000000 00100000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000100 00000000
2211 00000010 00001010 00000000 00000000 00001010 00001010 00000000 10011010
2300 00000000 00000000 00000000 00000000 00000000 00000000 10000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 11000000
PK1 2040 993 570 1701 1200 768 785 1243 772
PK2 2041 -4260 -3578 -6391 -6059 -4492 -4179 -4058 -3819
PK3 2042 -1311 -1309 -1315 -1339 -1347 -1347 -2697 -1357
PK1V 2043 106 113 192 193 230 225 7 652
PK2V 2044 -953 -1009 -1721 -1727 -2057 -2016 -87 -5836
PK3V 2045 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 3980 3762 2204 2197 1845 -1882 -13022 650
BLCMP 2048 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510
RESERV 2052 6000 6000 4800 4800 4800 4800 0 2800
PPMAX 2053 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 3787
PHYST 2055 319 319 319 319 319 319 319 319
EMFCMP 2056 -6430 0 0 0 -20500 0 0 0
PVPA 2057 -10510 -11788 -8199 -8203 -7697 -7697 0 -2088
PALPH 2058 -2575 -1734 -747 -1178 -2512 -2512 0 -5000
PPBAS 2059 0 0 0 0 0 0 0 0
TQLIM 2060 8010 7282 7282 7282 7282 7282 4855 7282
EMFLMT 2061 0 0 0 0 0 0 120 0
POVC1 2062 32446 32433 32520 32548 32515 32501 32729 32322
POVC2 2063 4029 4184 3101 2755 3166 3332 483 5579
TGALMLV 2064 4 4 4 4 4 4 4 4
POVCLMT 2065 11998 12461 9224 8192 9418 9912 621 26742
PK2VAUX 2066 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0
AALPH 2074 8192 12288 8192 12288 4096 12288 0 12288
OSCTPL 2077 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0
RTCURR 2086 1784 1888 2085 2092 2306 2259 578 3187
TDPLD 2087 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0
DBLIM 2102 15000 0 15000 15000 0 0 0 0
ABVOF 2103 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0
TRQCST 2105 201 190 517 516 1170 2215 4566 8472
LP24PA 2106 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0
MGSTCM 2110 1553 1553 32 774 1815 1815 0 267
DETQLM 2111 7712 10300 5191 5191 0 0 0 2218
AMRDML 2112 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0
NINTCT 2127 1443 2573 2388 4787 1688 3354 0 3029
MFWKCE 2128 1401 1001 2000 4000 2500 3000 0 2700
MFWKBL 2129 3335 2568 2568 2320 2829 2833 0 777
LP2GP 2130 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0
PHDLY1 2133 7712 8220 7701 7701 5140 5150 0 2068
PHDLY2 2134 8992 8990 5141 5141 8995 8990 0 6410
DGCSMM 2159 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 128 0 0 140
POVC21 2162 32766 32766 32765 32765 32764 32763 0 32756
POVC22 2163 27 31 38 39 48 58 0 151
POVCLMT2 2164 5069 5676 6924 6969 8124 9912 0 13949
MAXCRT 2165 45 25 85 45 165 85 365 365
ACCBSLM 2304 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0 22
DCIDBS 2310 0 0 0 0 0 0 0 1112
* Changed or added parameters are described in the frames.
TITLE
DRAW. No. CUST.
B-65270EN/07-049
SHEET 4/6
Table2
Motor Model βiF4 βiF4 βiF8 βiF8 βiF12 βiF12 βiF22 βiF22
/3000 /3000 /2000 /2000 /2000 /2000 /2000 /2000
40A 40A 40A 80A
Motor Specification 0051 0051 0052 0052 0053 0053 0054 0054
Motor ID Number 483 484 485 486 487 488 489 490
Symbol FS0i-D
2003 00001000 00001000 00001000 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00100000 00100000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2013 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110
2014 00000000 00001110 00000000 00001110 00000000 00001110 00000000 00001110
2210 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00000010 00000010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
PK1 2040 1240 2480 1276 2552 1875 3750 2320 4640
PK2 2041 -6415 -12830 -6288 -12576 -9137 -18274 -10593 -21186
PK3 2042 -1309 -1309 -1326 -1326 -1339 -1339 -1347 -1347
PK1V 2043 231 115 300 150 559 280 542 271
PK2V 2044 -2068 -1034 -2685 -1342 -5008 -2504 -4851 -2426
PK3V 2045 0 0 0 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235 -8235 -8235 -8235
POA1 2047 3670 7339 2827 5654 1516 3031 1565 3129
BLCMP 2048 0 0 0 0 0 0 0 0
DPFMX 2049 0 0 0 0 0 0 0 0
POK1 2050 956 956 956 956 956 956 956 956
POK2 2051 510 510 510 510 510 510 510 510
RESERV 2052 4200 4200 2800 2800 2800 2800 2400 2400
PPMAX 2053 21 21 21 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0 0 0 0
PVPA 2057 -5915 -5901 -3854 -3847 -1804 -1798 -2597 -2578
PALPH 2058 -1500 -750 -1236 -618 -2500 -1250 -1942 -971
PPBAS 2059 0 0 0 0 0 0 0 0
TQLIM 2060 7282 3641 7282 3641 7282 3641 7282 3641
EMFLMT 2061 0 0 0 0 0 0 0 0
POVC1 2062 32546 32537 32297 32297 31979 31986 32105 32105
POVC2 2063 2781 2888 5890 5890 9861 9769 8282 8282
TGALMLV 2064 4 4 4 4 4 4 4 4
POVCLMT 2065 7442 1860 14063 3516 20702 5175 18179 4545
PK2VAUX 2066 0 0 0 0 0 0 0 0
FILTER 2067 0 0 0 0 0 0 0 0
FALPH 2068 0 0 0 0 0 0 0 0
VFFLT 2069 0 0 0 0 0 0 0 0
ERBLM 2070 0 0 0 0 0 0 0 0
PBLCT 2071 0 0 0 0 0 0 0 0
SFCCML 2072 0 0 0 0 0 0 0 0
PSPTL 2073 0 0 0 0 0 0 0 0
AALPH 2074 12288 0 8192 0 8192 0 4096 0
OSCTPL 2077 0 0 0 0 0 0 0 0
PDPCH 2078 0 0 0 0 0 0 0 0
PDPCL 2079 0 0 0 0 0 0 0 0
DPFEX 2080 0 0 0 0 0 0 0 0
DPFZW 2081 0 0 0 0 0 0 0 0
BLENDL 2082 0 0 0 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0 0 0 0
RTCURR 2086 1655 827 2269 1134 2825 1412 2646 1323
TDPLD 2087 0 0 0 0 0 0 0 0
MCNFB 2088 0 0 0 0 0 0 0 0
BLBSL 2089 0 0 0 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0 0 0 0
ADFF1 2092 0 0 0 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0 0 0 0
RADUSL 2096 0 0 0 0 0 0 0 0
SMCNT 2097 0 0 0 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400 400 400 400
INPA1 2100 0 0 0 0 0 0 0 0
INPA2 2101 0 0 0 0 0 0 0 0
DBLIM 2102 0 0 0 0 15000 7500 0 0
ABVOF 2103 0 0 0 0 0 0 0 0
ABTSH 2104 0 0 0 0 0 0 0 0
TRQCST 2105 190 380 277 554 350 700 680 1360
LP24PA 2106 0 0 0 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0 0 0 0
RESERV 2108 0 0 0 0 0 0 0 0
BELLTC 2109 0 0 0 0 0 0 0 0
MGSTCM 2110 1289 530 1552 800 0 1280 1548 792
DETQLM 2111 3900 3900 3880 3880 2168 2168 2600 2600
AMRDML 2112 0 0 0 0 0 0 0 0
NFILT 2113 0 0 0 0 0 0 0 0
NINTCT 2127 2544 2544 2380 2380 4150 4150 3695 3695
MFWKCE 2128 5000 10000 4500 9000 12000 24000 4000 8000
MFWKBL 2129 1812 1812 1550 1550 1044 1044 1046 1046
LP2GP 2130 0 0 0 0 0 0 0 0
LP4GP 2131 0 0 0 0 0 0 0 0
LP6GP 2132 0 0 0 0 0 0 0 0
PHDLY1 2133 3855 3855 3860 3860 5150 5150 2070 2070
PHDLY2 2134 8995 4387 8990 4382 8990 4382 9000 4392
DGCSMM 2159 0 0 0 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0 0 0 0
OVCSTP 2161 0 0 0 0 0 0 0 0
POVC21 2162 32755 32755 32756 32756 32756 32756 32756 32756
POVC22 2163 157 158 153 151 151 150 148 147
POVCLMT2 2164 3708 927 7007 1752 10315 2579 9058 2265
MAXCRT 2165 25 45 25 45 25 45 45 85
ACCBSLM 2304 0 0 0 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0 0 0 0
TITLE
DRAW. No. CUST.
B-65270EN/07-049
SHEET 5/6
Table 3
Motor model βiF30 αiF8 αiF8 αiF22 αiF22
/1500 /4000 /4000HV /4000 /4000HV
Motor Specification 0055 0228 0220 0248 0240
Motor ID Number 491 492 493 494 495
Symbole FS0i-D
2003 00001000 00001000 00001000 00001000 00001000
2004 00000011 00000011 00000011 00000011 00000011
2005 00000000 00000000 00000000 00000000 00000000
2006 00000000 00000000 00000000 00000000 00000000
2007 00000000 00000000 00000000 00000000 00000000
2008 00000000 00000000 00000000 00000000 00000000
2009 00000000 00000000 00000000 00000000 00000000
2010 00000000 00000000 00000000 00000000 00000000
2011 00000000 00000000 00000000 00000000 00000000
2012 00000000 00000000 00000000 00000000 00000000
2013 00000000 00000000 00000000 00000000 00000000
2014 00000000 00000000 00000000 00000000 00000000
2210 00000000 00000000 00000000 00000000 00000000
2211 00001010 00001010 00001010 00001010 00001010
2300 00000000 00000000 00000000 00000000 00000000
2301 00000000 00000000 00000000 00000000 00000000
PK1 2040 2238 526 526 1214 1214
PK2 2041 -13330 -3270 -3270 -5208 -5208
PK3 2042 -1347 -1322 -1322 -1343 -1343
PK1V 2043 332 90 90 170 170
PK2V 2044 -2973 -807 -807 -1523 -1523
PK3V 2045 0 0 0 0 0
PK4V 2046 -8235 -8235 -8235 -8235 -8235
POA1 2047 2553 4704 4704 2492 2492
BLCMP 2048 0 0 0 0 0
DPFMX 2049 0 0 0 0 0
POK1 2050 956 956 956 956 956
POK2 2051 510 510 510 510 510
RESERV 2052 2100 5600 5600 4800 4800
PPMAX 2053 21 21 21 21 21
PDDP 2054 1894 1894 1894 1894 1894
PHYST 2055 319 319 319 319 319
EMFCMP 2056 0 0 0 0 0
PVPA 2057 -1545 -10007 -10007 -7696 -7696
PALPH 2058 -1300 -1593 -1593 -2574 -2574
PPBAS 2059 0 0 0 0 0
TQLIM 2060 7282 7282 7282 7282 7282
EMFLMT 2061 0 0 0 0 0
POVC1 2062 32589 32522 32522 32487 32487
POVC2 2063 2239 3078 3078 3517 3517
TGALMLV 2064 4 4 4 4 4
POVCLMT 2065 5986 9154 9154 9418 9418
PK2VAUX 2066 0 0 0 0 0
FILTER 2067 0 0 0 0 0
FALPH 2068 0 0 0 0 0
VFFLT 2069 0 0 0 0 0
ERBLM 2070 0 0 0 0 0
PBLCT 2071 0 0 0 0 0
SFCCML 2072 0 0 0 0 0
PSPTL 2073 0 0 0 0 0
AALPH 2074 8192 12288 12288 8192 8192
OSCTPL 2077 0 0 0 0 0
PDPCH 2078 0 0 0 0 0
PDPCL 2079 0 0 0 0 0
DPFEX 2080 0 0 0 0 0
DPFZW 2081 0 0 0 0 0
BLENDL 2082 0 0 0 0 0
MOFCTL 2083 0 0 0 0 0
RTCURR 2086 1490 1588 1588 1827 1827
TDPLD 2087 0 0 0 0 0
MCNFB 2088 0 0 0 0 0
BLBSL 2089 0 0 0 0 0
ROBSTL 2090 0 0 0 0 0
ACCSPL 2091 0 0 0 0 0
ADFF1 2092 0 0 0 0 0
VMPK3V 2093 0 0 0 0 0
BLCMP2 2094 0 0 0 0 0
AHDRTL 2095 0 0 0 0 0
RADUSL 2096 0 0 0 0 0
SMCNT 2097 0 0 0 0 0
DEPVPL 2098 0 0 0 0 0
ONEPSL 2099 400 400 400 400 400
INPA1 2100 0 0 0 0 0
INPA2 2101 0 0 0 0 0
DBLIM 2102 0 0 0 0 0
ABVOF 2103 0 0 0 0 0
ABTSH 2104 0 0 0 0 0
TRQCST 2105 1630 461 461 1083 1083
LP24PA 2106 0 0 0 0 0
VLGOVR 2107 0 0 0 0 0
RESERV 2108 0 0 0 0 0
BELLTC 2109 0 0 0 0 0
MGSTCM 2110 2059 1300 1300 1547 1547
DETQLM 2111 2148 6500 6500 5495 5495
AMRDML 2112 0 0 0 0 0
NFILT 2113 0 0 0 0 0
NINTCT 2127 6680 1631 1631 2226 2226
MFWKCE 2128 14000 3139 3139 5518 5518
MFWKBL 2129 539 3089 3089 2326 2326
LP2GP 2130 0 0 0 0 0
LP4GP 2131 0 0 0 0 0
LP6GP 2132 0 0 0 0 0
PHDLY1 2133 1054 5141 5141 5141 5141
PHDLY2 2134 9000 8981 8981 8981 8981
DGCSMM 2159 0 0 0 0 0
TRQCUP 2160 0 0 0 0 0
OVCSTP 2161 0 0 0 128 0
POVC21 2162 32755 32765 32765 32762 32762
POVC22 2163 157 40 40 75 75
POVCLMT2 2164 2982 5746 5746 7898 7898
MAXCRT 2165 85 85 45 165 85
ACCBSLM 2304 0 0 0 0 0
ACDCEND 2305 0 0 0 0 0
DCIDBS 2310 0 0 0 0 0
TITLE
DRAW. No. CUST.
B-65270EN/07-049
SHEET 6/6

Parameter Manual

Uploaded by

Copyright:

Available Formats

Parameter Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Parameter Manual

Uploaded by

Copyright:

Available Formats

FANUC AC SERVO MOTOR @* series

FANUC AC SERVO MOTOR #* series

FANUC LINEAR MOTOR L*S series

■General Safety Precautions

DEFINITION OF WARNING, CAUTION, AND NOTE

- Read this manual carefully, and store it in a safe place.

2 SETTING αiS/αiF/βiS SERIES SERVO PARAMETERS....................... 8

3 αiS/αiF/βiS SERIES PARAMETER ADJUSTMENT............................ 78

3.3.6 Stick Slip ..............................................................................................................131

4 SERVO FUNCTION DETAILS ............................................................ 133

4.6.7 Two-stage Backlash Acceleration Function .........................................................223

4.15 SYNCHRONOUS BUILT-IN SERVO MOTOR PARAMETER SETTING ... 346

5 DETAILS OF PARAMETERS ............................................................. 473

6 PARAMETER LIST ............................................................................. 505

C FUNCTION-SPECIFIC SERVO PARAMETERS ................................. 553

I SERVO CHECK BOARD OPERATING PROCEDURE ...................... 637

Chapter 1, "OVERVIEW", consists of the following sections:

1.1 SERVO SOFTWARE AND SERVO CARDS SUPPORTED

1.1 SERVO SOFTWARE AND SERVO CARDS SUPPORTED

Series 21i-MODEL B (Note1) Series 9096/A(01) and subsequent editions 320C52

Series 0i Mate-MODEL B (Note1)

Series 90B5/A(01) and subsequent editions

Series 90D0/A(01) and subsequent editions

2 The servo software Series 9096 is compatible with

Servo software series map

HRV1 supported, αi not supported

For Series 16i , For Series 0i-C For Series 16i ,

90B6 90B5 90B1 90B8

1.2 ABBREVIATIONS OF THE NC MODELS COVERED BY

In this manual, the NC product names are abbreviated as follows.

NC product name Abbreviations

FANUC Series 0i Mate-MODEL B Series 0i Mate-B

1.3 RELATED MANUALS

The following manuals are available for FANUC AC SERVO

Table 1.3 Related manuals of SERVO MOTOR αiS/αiF/βiS series

Other manufactures’ products referred to in this manual

The following αi/βi Pulsecoders are available.

Pulsecoder name Resolution Type

2 SETTING αiS/αiF/βiS SERIES SERVO

2.1 INITIALIZING SERVO PARAMETERS....................................9

2.1 INITIALIZING SERVO PARAMETERS

2.1.1 Before Servo Parameter Initialization

2.1.2 Parameter Initialization Flow

Servo parameter setting

CNC restart → 2.1.3 (12)

Absolute position detector setting → 2.1.3 (13)

Completion of servo parameter initialization

2.1.3 Servo Parameter Initialization Procedure

Fig. 2.1.3(a) PARAMETER SETTING SUPPORT screen

(Standard screen) (Conventional compatible screen)

Fig. 2.1.3(b) 0i-C Servo tuning screen

If no servo screen appears, set the following parameter as shown, and

Fig. 2.1.3(c) Servo setting screen Correspondence of Power Mate i

Reset initialization bit 1 to 0.

(3) Motor ID No. setting

αiS series servo motor

αiF series servo motor

αiS series servo motor (for 400-V driving)

αiF series servo motor (for 400-V driving)