Cognex In-Sight 2000 Training: Provided by

Cognex In-Sight 2000 Training
Provided by
Downloaded from www.Manualslib.com manuals search engine

Table of Contents
Introduction: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Connecting to the IS2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Up Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Poker Chip Lab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Locate Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Inspect Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Filmstrip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Save Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Run Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Logic Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Introduction:
The In-Sight 2000 is a vision sensor, capable of providing a pass/fail output from the inspection of a
part. It is easier to use than a full vision system but has capabilities beyond a basic photosensor or
proximity sensor, or even an array of sensors. It uses the same software used for programming a
Cognex In-Sight vision system, so you don’t need to learn a separate software to configure it.
You will learn about the In-Sight 2000, its components, interchangeable parts, configuring an IP
address, connecting to the IS2000 and programming an inspection. This document will also serve
as a reference for the primary functionality of EasyBuilder and the stepwise process for building an
inspection.
In the first lab you will be guided in each step, which will be explained in detail. After that you can
use your own parts (if you brought some) to create an inspection for your application or use our
parts and create an inspection according to set criteria.
1
Connecting to the IS2000
Once you have installed the software you can communicate to the In-Sight 2000. As it
communicates over Ethernet TCP/IP you will need to provide it with an IP address so that it will
communicate to your computer. As a default all In-Sight systems are configured as DHCP (Dynamic
Host Configuration Protocol) so out of the box it is expecting to be “served” an IP address. If your
computer does not have DHCP Server software on it (most computers don’t) then you need to
assign the In-Sight 2000 and your computer static IP addresses. This section will show you how to
do that. Launch In-Sight Explorer version 5.2.3 from the icon on your desk top if it is not already
open. When it opens you will see at the left side a pane labeled Application Steps and the first step
is Get Connected; place your cursor on this step and click the mouse to select it (if it is not already
highlighted) (Fig. 1).
Fig. 1: Application Steps - Get Connected
2
When this step is selected the pane just below it will appear as seen in Fig. 2. Any In-Sight system
that is on the same subnet as the computer will appear here. If you have obtained an offline
programming key, the name of your computer will appear in this pane followed by local emulator.
This means that you can work with the software without being connected to an In-Sight vision
system.
Fig. 2: Connected Systems
The Connect button will establish a connection to the system selected in the list. The Disconnect
button will cause the software to be disconnected from the system to which it is currently connected.
The Refresh button will refresh the list of systems in the left side of the pane that are currently on the
same subnet as the computer. The Add button will launch a dialog to assign an IP address to a
system not on the same subnet as the computer. The Emulator button allows you to select which
system you would like to emulate if using the offline programming functionality.
Click the Add button to launch the Add Sensor dialog (Fig. 3 on next page)..
3
Fig. 3: Add Sensor/Device to Network
The connected In-Sight 2000 should have been discovered and displayed in the list of devices.
Click on the line that shows the unit to select it. From this dialog you can change the name of the
unit if you desire. Notice that at this point the setting of the IP address is selected as DHCP. Click
on the radio button next to Use The Following Network Settings. When you do this the entry fields
and button below it become active (no longer grayed out). If you know the subnet of your computer
and what address you would like to use and the subnet mask you can enter those into the
appropriate fields. An easier method is to click the Copy PC Network Settings button. This will use
the settings of the Ethernet network adapter in your computer to assign an appropriate IP address
and the subnet mask to your In-Sight 2000. This assumes that your computers Ethernet network
adapter is not set to DHCP.
From this dialog you can also reset the administrative logon password (if it had been set and
forgotten) and reset the entire system to factory defaults; all system settings except for the IP
address will be reset.
4
Click Apply at the bottom of the dialog; when you do this another dialog (Fig. 4) will appear, warning
you of the changes about to take place. Click OK at the bottom of the message box to continue with
changing the IP Address. When the process has finished another message box will appear noting
the success of the change; click OK at the bottom of this dialog as well. Click Close at the bottom of
the Add Sensor/Device to Network dialog.
Fig. 4: Add Sensor Message Box
When the dialog closes you should now see your In-Sight 2000 listed in the pane showing In-Sight
systems on your subnet (Fig. 2 on page 3). Click on it to select it and click the Connect button. You
will see the software appearance change while attempting to connect to the In-Sight 2000 and after
several seconds you will then see that it is connected. You are ready to move to the next
application step.
5
Set Up Image
Click on the Set Up Image application step button (Fig 5). When you do this the pane at the bottom
will change to show the image acquisition settings.
Fig 5: Application Steps - Set Up Image
Fig 6: Image Acquisition Settings
6
There are multiple sections to this pane which will be explained in more detail.
Fig. 7: Acquire/Load Image

The first section (Fig. 7) is for image acquisition. Pressing the Trigger button will acquire a single
image. Pressing the Live Video button will acquire images as fast as possible without doing any
processing or inspection of the image. Clicking the Load Images from PC button will open a
navigation dialog to allow navigation to a folder that contains images. Typically you would want
these to be images saved from your system as they will have been illuminated by your system in a
manner you intended.
Fig. 8: Trigger
The next section (Fig. 8) selects how the system will be triggered when inspections are running.
There are four selections for trigger type. Camera is the setting if the dedicated trigger input is being
used to acquire images at runtime. The Delay control is active in this mode and allows for a delay
between the receipt of the trigger signal and the start of acquisition; Interval is disabled. Continuous
will capture images as fast as possible while performing the inspection, setting the I/O and
performing communications. The Interval control sets a time between acquisitions to reduce the
possibility of an acquisition being lost. The Delay control is disabled for this trigger type. The
Manual trigger type allows the In-Sight 2000 to be triggered from In-Sight Explorer software. Both
Delay and Interval are disabled for this type. Selecting Real Time Ethernet allows triggering
via an Ethernet industrial protocol.
7
Fig 9: Light and Exposure Settings
The next section (Fig. 9) configures the intensity of the light and the exposure settings.
First the exposure time can be set to a defined exposure time (Manual Exposure) or to a variable
exposure time (Auto Exposure). The latter has two ways of calculating the exposure time and these
are defined in the help files.
Target Brightness is used when Auto Exposure is selected and sets a desired average
brightness level for the resulting image; the range is from 0 to 100.
The Exposure Region sets the region of the image over which the calculated automatic exposure
levels are based.
The Light Intensity control sets the relative percentage of output from the integrated light; the range
is from 0 to 100.
The Exposure (msec) control sets the exposure time in milliseconds. This setting and the Light
Intensity setting control the image brightness when using Manual Exposure.
The Optimal Exposure control computes an exposure time based on the Light Intensity and Target
Brightness settings when using Manual Exposure.
The Light Control Mode control sets the integrated light to either be strobed on during the exposure
time or disables the integrated light.
When deciding on settings it is typically advised that the brightest area of the image be about ninety
percent of full value. When an area is saturated (at full white value) information about the size of
dark objects in that region is less accurate and typically provides no advantage in the efficacy of the
tools. Since each part and application are different this may not always be possible, so this is a
general guideline.
8
Fig. 10: Image Size
The final section of this pane controls the size of the image that is captured (Fig. 10). The upper
control in this section will set the number of rows that are captured in each image. This can be
useful if the part does not move much in the field of view and cycle time must be reduced. When
only a portion of the rows are captured, the acquisition time is reduced which decreases the cycle
time.
The other control, Image Magnification Mode reduces the size of the field of view by fifty percent so
that a smaller portion of what was in the field of view is imaged, while retaining the resolution of the
image. It provides the effect of doubling the focal length of the lens. The image on the left (Fig. 11
left) shows the image with an 8mm focal length lens and a working distance of six inches. The
image on the right (Fig. 11 right) shows the same setup with Image Magnification Mode enabled.
Both images are 640 by 480 pixels.
Fig. 11: Image Magnification Mode
9
Poker Chip Lab
The first lab uses Cognex poker chips; each lab station should have a few of these chips. When
developing an inspection you would follow the Application Steps from top to bottom to create a
complete, fully functional inspection.
You have already finished the Get Connected step and learned about the Set Up Image step, so
now you can complete this step for your part. Set up your image to appear similar to the left image
in Fig. 11 with the same side facing up. In setting the exposure time for this part you may notice that
the area in the center of the chip is a highly reflective material. Adjusting the exposure settings for
this part such that the brightest area is at about ninety percent of full value leaves the image a bit
darker than desired. For this lab you will use the Manual Exposure mode, set the Target Brightness
to 50 and the Light Intensity to 70 and then click the Compute button. Your exposure time should
probably be around 0.2 to 0.3 milliseconds but it may vary more depending on the ambient light.
The next Application Step is the Locate Part step; click on this step (Fig. 12).
Fig 12: Application Steps - Locate Part

10
When you click on this step the pane at the bottom will change to expose a list of tools (Fig. 13) that
can be used to locate your part. In your system there are four tools that can be used for locating a
part; in the other two models (lower cost and lower capability) of In-Sight 2000 only the Pattern tool
is available. To the right of the list is a description of what the tool does and how to proceed adding
it to your inspection.
Fig. 13: Locate Part Tool List
For this lab you will use the Pattern tool so click on Pattern to select it and then click the Add button
at the top right of this list. When you do this two rectangles will appear on the image; these are the
Model region and the Search region of the Pattern tool (Fig. 14 on next page).
11
Fig. 14: Locate Part - Pattern Tool
The Model region appears pink, which signifies it is selected for editing. If the cursor is placed inside
the rectangle it will appear as a white cross with arrowheads at each point. If you click and hold the
left mouse button, the rectangle can be dragged to its desired location. If you place the cursor on an
edge or a corner of the rectangle it will appear as a white line with arrowheads at each end. If you
click and hold the left mouse button, the rectangle can be resized in one direction (if on a side) or in
two directions (if on a corner) by dragging. At the middle of the bottom edge of the rectangle is an
arc with an arrowhead at one end. By placing the cursor over this graphic it will appear as a hand
with the index finger extended. When the cursor appears as the hand, click and hold the left mouse
button to rotate the region by dragging it one way or the other. Move, resize and rotate (if
necessary) the Model region to match the image on the next page (Fig. 15).
12
Fig. 15: Locate Part - Trained Model
Placing the Model region close around the graphic on the chip allows defining edges to be trained
while disregarding a significant amount of the background that could also contain significant
variations. When choosing a pattern to use as a fixturing point you want something that would
normally be present, is fairly unique and not too symmetrical, so that orientation of the found pattern
is consistent and repeatable. The graphic that has been chosen meets those criteria.
13
Fig. 16: Locate Part - Select Search Region
Placing your cursor on the edge of the Search region and clicking the left mouse button will make it
appear pink and the Model region will appear green (Fig. 16). At this point you could move and
resize the Search region as you did with the Model region; the size and location of the Search region
would be determined by the expected range of movement of the part in the field of view. Since you
will be moving this part in the field of view by hand you can leave the Search region at its default
size and location.
14
Fig. 17: Locate Part - Accept Regions
When the Model and Search regions have been set as desired, click the OK button in the Directions
pane (Fig. 17) at the bottom of the window to accept the changes and finish adding the tool. When
you click OK the tool will appear in the Results tab of the palette (Fig. 18) on the right side of the
window and the Edit Tool pane (Fig. 19), containing settings for the tool, will appear in the bottom of
the window.
Fig. 18: Palette - Results Tab
Fig. 19: Edit Tool Pane
15
Fig. 20: Pattern Tool Settings - Name and Model Region
On the right side of the Edit Tool pane are several entry fields and a control to retrain the Model
should that be necessary. First you can assign a Name to the tool; while this is not required, as the
software gives it a default name, it is a good practice to provide a descriptive name. This allows
someone who is looking at the program to have an understanding of the function of this tool in the
inspection. Consider changing the Name of this tool to LocatePart.
The next control allows you to select if the tool is Enabled. The choices in this drop list are Enabled,
Disabled, and Input 0. Normally the tools you add to the inspection would be enabled as you
need them to perform some function in the inspection. So why would you disable a tool? This can
be useful in troubleshooting the inspection, to determine how a specific tool might be affecting the
overall result. Selecting Input 0 would enable the tool only when Input 0 is active. Perhaps you
have two similar parts with one feature difference and a specific tool or tools are only needed for
inspection of this different feature. This allows you to create one program that will inspect both parts
and only enable the extra tool or tools to inspect the part with the feature difference.
There is also an entry field for providing a Description of the tool’s function. Again this is not
required but documenting your work helps others understand what you have done and perhaps
helps you to remember why this tool was part of the inspection, when you look at it for the first time
six months after you originally created the program. Develop the habit of documenting your work.
On the far right side of the pane is an image of your Model with a button below it labeled Model
Region. If you decide at some later point that you need to retrain the Model, you can click
this button. When you do this the Model region will appear in the image and can be edited in the
manner used when the tool was created. The button label will also change to Train, so that when
you finish editing the region you again click the button and the new model will be accepted; the
image of the new model will replace the image of the old model.
With the exception of the ability to retrain a Model these controls will be available on all of the tools.
16
1 2
Fig. 21: Pattern Tool Settings - Angle and Acceptance
On the left side of the Edit Tool pane (Fig. 21) are settings that relate to the manner in which the tool
functions.
In the upper left of this pane is an indicator that signifies if this tool passes or fails which is based on
the tool settings and the runtime image.
Below the Pass/Fail indicator is a control to adjust the Rotation Tolerance of the found pattern. This
control sets how much the pattern can be rotated from its trained position before the match score is
affected. The default value is plus and minus 45 degrees and the range is from zero degrees to plus
and minus 180 degrees. Adjustment of the control can be made by placing the cursor on the box
above either numeric value, clicking and holding the left mouse button and dragging it to the desired
angle; both positive and negative values will be affected equally. Additional ways to adjust the
control include entering a numerical value into either of the boxes showing a value; both values will
be affected equally. If you enter a positive value into the box for the negative value both will go to
zero, so make sure to include the sign. For fine adjustment you can click either of the boxes above
the numeric values and use the right and left arrow keys on your keyboard to increase or decrease
the value. Regardless of which method is used, the image above either control rotates to the
appropriate angle.
Below this control is the Part Finding Meter. The vertical bar with the numeric value beneath it is the
pass/fail threshold; a match score greater than or equal to this value indicates the tool passes and
score less than this value indicates the tool fails. Setting this value can be done in the same manner
as adjustment of the Rotation Tolerance. The green bars show the current magnitude of the match
score. If you hover over the control, a numeric value of the match score will be displayed. Setting
the threshold value should reflect what you are attempting to do. If you are trying to locate a part
you will want to keep this relatively low so that you include a wider range of possibilities.
There are two buttons in the lower left corner. The one labeled “1” allows for a scale variance of
plus and minus ten percent before the match score is affected. The one labeled “2” opens a control
for setting a timeout period for the tool. The Execution Time in milliseconds for the tool is shown in
the lower right corner.
17
For this lab leave the threshold at 50 and set the Rotation Tolerance to 180. Test your part location
tool by placing the In-Sight 2000 into Repeating Trigger mode and moving and rotating the part
within the field of view to assure that the part is found. If it is not properly located please ask for
help. Place the part in approximately the same position as when you originally added the part
locating tool. Turn off Repeating Trigger mode.
Now that the part can be located in the field of view the next step is to inspect it to make sure that
the correct side of the chip is facing up. On one side of the chip there is a horseshoe and two
stacks of chips; the other side has a pair of dice and one stack of chips. We will use both of these
features to insure the side with the horseshoe is facing up. Click on the Inspect Part step in the
Application Steps pane (Fig. 22).
Fig. 22: Application Steps - Inspect Part
18
When this step is selected the Add Tool pane at the bottom of the window will appear showing the
various tools available. The tools are grouped according to what they do and if you expand each
group you would see the following (Fig. 23). The Presence/Absence Tools detect the presence of
one object. The Measurement Tools determine if a distance, size or angle are within acceptable
limits. The Counting Tools determine if the number of a type of object found in a region is within
acceptable limits. The Math & Logic Tools allow you to create basic logic from tool outputs to drive
digital outputs.
Fig. 23: Inspect Part - Available Tools
The first inspection tool to be added is a Pattern tool from the Presence/Absence Tools group to find
the horseshoe on the poker chip. This will function in the same manner as the tool used to locate
the part in the field of view. Select Pattern and click the Add button (Fig. 24).
Fig. 24: Inspect Part - Add Tool Pane
19
Fig. 25: Inspect Part - Pattern Regions
The Model and Search regions can be moved and sized, as done with the pattern tool for locating
the part, so that they appear similar to the image above (Fig. 25). Notice now that the search region
is much smaller than was used for locating the part. With such a small search region how will the
horseshoe be found? Click the OK button in the Directions pane to accept adding the tool.
20
Fig. 26: Inspect Part - Pattern Settings
At the right side of the Edit Tool pane (Fig. 26) we see the same controls that we saw in the same
section of the pane for the part location tool but we also see an extra control, labeled Fixture.
EasyBuilder automatically uses location information from the first part location tool added, to fixture
other tools to the appropriate section of the part (this is why the search region can be kept small).
As the part moves and rotates, the fixtured tools keep their relative position. If you don’t want to
fixture your tool to the part location tool, click the pushpin icon next to the drop list to turn off this
functionality. If you had added a second part location tool to the program you could select it from the
drop list and the tool would be fixtured based on the second part location tool. Consider naming this
tool Horseshoe.
Fig. 27: Inspect Part - Pattern Settings
At the left side of the Edit Tool pane (Fig. 27) we see the same controls present in the same section
of the pane for the part location tool and again we see an extra control. It is to the left of the control
for allowing a variation in scale and it looks like the graphic associated with a normally closed
contact. Clicking this tool inverts the tool, so rather than looking for the presence of a pattern and
passing if it meets the selection criteria, it now looks for the pattern to be absent and the tool passes
when the pattern is not found. Notice that the Rotation Tolerance has been set to zero. Since this
tool is fixtured, as the part rotates so will this tool’s search region. As long as the horseshoe keeps
the same relative orientation it will be found. If it were upside down perhaps, then with these
settings the horseshoe would not be found. You can leave the threshold at 50.
21
Before doing any testing you will add another tool; this time you will go back to the Add Tool pane
and from the Absence/Presence Tools group you will select Pixel Count and click the Add button
(Fig. 28).
Fig. 28: Inspect Part - Pixel Count
This time there will only be one region in the image. Move and resize it to appear like the image
below (Fig. 29). Click the OK button in the Directions pane to accept adding the tool.
Fig. 29: Pixel Count - Set Region

22
1
Fig. 30: Pixel Count - Settings
The right side of the settings pane for the pixel count tool has similar controls to the Pattern tool
(without the image of the Model and the Model Region button). Consider naming this tool Chip
Stacks. The left side of the settings pane (Fig. 30) appears differently. By default when the tool is
inserted, its automatic settings are initiated for ease of use, which explains why the controls are
already set and the tool indicates a passing condition. The Pass/Fail indicator is present as it will be
on all tools.
The Pixel Selector control specifies which pixels are counted. This tool works in gray scale rather
than as a binary tool. That means instead of having one threshold to determine which pixels are
considered white or black, there are two thresholds; those pixels whose intensities are within the
designated range are counted and those whose intensity falls outside of the range are not counted.
The yellow horizontal bar on this control shows which pixels are counted. In this case it is acting as
a binary tool; pixels whose intensity is between zero and 165 are counted and those whose intensity
is greater than 165 are not counted. The button at the right end of this control (labeled “1”) inverts
the selected pixels. Pressing this button would count the pixels outside the selected range and
ignore the pixels within the range.
The Pixel Count Meter and Pass Range control specifies the minimum and maximum pixel counts
for pass/fail determination. The yellow bar shows the current count and if you hover over the control
a numerical value for the result is shown.
The Auto buttons on the left side of each control will automatically set the values based on the
current image. The level controls for either can be manually adjusted as was done for the
acceptance angle of the part locating tool (reference page 18).
You have finished adding the tools for the desired inspection so now you can test your application.
Move and rotate the chip to assure that the tools follow the part and inspect it correctly. Turn the
chip over to confirm that the inspection now fails. Try other chips to confirm that the inspection
works for them in the intended manner. If the inspection does not work for all cases, make changes
to the settings to insure that it does. Ask for help if you can not make it work properly.
23
For the purposes of the lab you have finished once you are satisfied with your results. In your
process on the plant floor you would not be finished yet as you have not fully commissioned the
system. The rest of this manual will serve as a reference for the rest of the application steps. Click
on the next application step, Inputs (Fig. 31).
Fig. 31: Application Steps - Inputs
24
Fig. 32: Input Configuration
The pane at the bottom of the window will change. Settings for the one programmable input will
appear in this pane. The In-Sight 2000 has one dedicated trigger input for initiating an inspection
and one other input that can be configured from a small choice of options. A name can be assigned
to the input line. The Signal Type droplist sets the function of the input. The Edge Type droplist sets
whether the function occurs on the rising or falling edge of the input; it is only enabled when Reset
Counters or Job Change (Pulsed) are selected. The Force Input droplist allows a configured
input line to be forced on without the input being present when On is selected. When done testing
the input set the Force Input droplist to Off or None.
The following describes the various Signal Types.
The User Data allows a location or inspection tool (or tools) to be enabled or disabled based on the
input. This feature needs to be set in the settings pane of the desired tool or tools using the Enabled
droplist.
Selecting Reset Counters will reset the various inspection statistics counters to zero when the input
is present.
The Online/Offline selection allows turning on or off the inspection process from Input 0. When
Online an inspection can be initiated and the outputs and communications set according to
the results of the inspection. When Offline, an inspection can be initiated but the outputs and
communications will not be set according to the results of the inspection.
The last option Job Change (pulsed) lets the input select which job (inspection program) is loaded
into RAM so that it is the current inspection job. This requires that the job names stored in the
In-Sight 2000 have a numerical prefix (0 to 31) so that a pulse train, of specific structure, can select
the appropriate job. See the help files for the specific structure of the pulse train.
When you select another application step, the changes made are automatically saved in the vision
system (not in the job file).
25
The next step is configuring the outputs. Click on the Outputs step (Fig. 33).
Fig. 33: Application Steps - Outputs
26
Fig. 34: Output Settings
When the Output application step is selected the output settings pane will appear at the bottom of
the window. The In-Sight 2000 has four digital outputs and two LED’s on the body of the unit that
can be configured. Each output can be given a name. Each output can be assigned a Signal Type
of which there are multiple types too numerous to explain here; see the help files for a description of
the possibilities. Setting the Signal Type to Job Result allows the output to be assigned to the result
of the job or of a specific tool.
The Force Output can be used to test an output from the In-Sight 2000. The point must be
configured to a specific function and from the droplist choose On to force the output on. When you
are finished testing the output select Off or None from the list. Clicking the Details… button on the
far right opens a dialog (Fig. 35) for determining how the output will function.
Fig. 35: Output Details

By default an output will hold the last state it was in until it is changed. If the output is turned on by
the job passing it will stay on until the job fails; this could encompass multiple inspections. In the
Details dialog the output can be set to a pulse with the pulse length set by the user. Now if
the output is set by the job passing it will pulse on for the user set time and then turn off. From this
dialog you can also delay the setting of the output by a certain number of triggers of the vision
system or by a specific time.
27
Digital I/O is one way to control the In-Sight 2000 though it is not the only way. In-Sight systems can
communicate over a number of industrial protocols including EtherNet/IP and ProfiNet. Control of
the system and results from the system can be performed using industrial protocols so that no digital
I/O is necessary. How the In-Sight 2000 is controlled will depend on your application. Additionally
both communications and digital I/O can be used concurrently to best tailor the application to your
situation. Click on the Communication step (Fig. 36).
Fig. 36: Application Steps - Communication
28
When the Communication step is selected the pane at the bottom will change (Fig. 37). This pane
allows you to select and configure various communications paths. The EasyView selection allows
configuration of the way data will appear on a VisionView panel if one is being used. If
communications to a PLC/PAC or other industrial protocol gateway are to be configured click the
Add Device button.
Fig. 37: Communication - Add Device
When the Add Device button is clicked you will have a series of selection droplists to specify the
controller and protocol. The first droplist is the Device (Fig. 38). Your choices are None, PLC/
Motion Controller and Other. Selecting either of the latter two will produce another droplist
(Fig. 39 on next page).
Fig. 38: Device Selection
29
Fig. 39: Device Manufacturer
Each of the controller manufacturers has protocols they support. Mitsubishi supports SLMP (a
feature of CC-Link). Omron and Rockwell Automation both support EtherNet/IP and Siemens
supports ProfiNet. Selecting Other offers the same choice of protocols listed above but the
controller would come from some other manufacturer. Selecting one of these choices produces the
last droplist (Fig. 40). The Protocol selection may be made automatically or it may need to be
chosen based on the Manufacturer selected. If only one protocol is possible the selection will be
automatic. For this example Rockwell Automation and EtherNet/IP have been chosen. To accept
the choices click OK. The appropriate protocol would need to have previously been enabled (Get
Connected step, Sensor menu, Network Settings option).
Fig. 40: Communication Protocol
30
Fig. 41: Format I/O Data
When the OK button is clicked a pane for setting the input and output data will appear with a tab for
each of input data and output data (Fig. 41). Clicking the Add button at the lower left will open a
dialog from which data can be selected (Fig. 42).
Fig. 42: Add Data
Different data will be available for Input and Output. The available data will be dependent on what
has been added to the inspection. The Input data contains various control parameters for the tools
and the Output data is limited to pass or fail of each tool as well as various information about the Job
and Acquisition. The data point is added by either selecting the point and clicking the OK button or
double clicking on the point. When a point is selected it will be added to the appropriate pane with
information about the data type, size and the current value. Configuring communications data is that
easy.
31
In the Communication step you can also configure saving images from the system via FTP (File
Transfer Protocol). From the first communications configuration pane (see Fig. 37 on page 30)
select FTP. A new pane will appear in the bottom of the window with two tabs, Image and Settings.
Click the Add button in the lower left corner of the Image tab to add an FTP Image connection (Fig.
43).
Fig. 43: Add FTP Image Connection
When the connection is added you will see information given about the connection. At the right side
of this pane are the settings for the connection (Fig. 44).
Fig. 44: Write Image FTP Settings

These settings allow you to fully configure the name of the image, the image format, which images
are saved, if inspection graphics are included, adding a time stamp and a counter, if desired.
32
Fig. 45: FTP Connection Settings
On the Settings tab, two FTP connections can be defined (Fig. 45). These will set the path to the
computer on which the FTP Server exists and provide access credentials for that computer. The
FTP Settings button on the far right will open a dialog for defining the port and timeout
settings along with allowing passive transfers over FTP.
In-Sight Explorer can function as an FTP Server so it can be used to test your image transfers. If
this is being set up on the factory floor, using a third party FTP Server is suggested as it will provide
more flexibility and more security options for the connection.
33
Now that the job has been configured, I/O and communications have been set, just a few more steps
that cover some essential information of how the inspection runs must be covered. The next
application step is setting the Filmstrip. The Filmstrip is a feature that allows saving images from a
system during troubleshooting or setup of the inspection. Click the Filmstrip application step (Fig.
46).
Fig. 46: Application Steps - Filmstrip
34
Fig. 47: Filmstrip Settings
When the Filmstrip step is selected the pane at the bottom of the window changes (Fig. 47). The
settings in this pane control which images are put into the queue (Pass/Fail/Pass and Fail), the size
of the queue, the type of queue (Most Recent, First Only), the style of icon used to show which
inspections pass and fail during runtime and a path where the images can be saved. Once these
setting have been made and the system is set Online, images will be saved to the Filmstrip. While
the system is Online the Filmstrip might appear like the image below (Fig. 48).
Fig. 48: Filmstrip - Online

The images are not displayed as actual images in the filmstrip when the system in Online but as
icons that represent which images pass and which fail. This is done to minimize the time used for
this control so that the inspection can run faster. When the system is taken Offline the appearance
changes (Fig. 49) which shows the actual images.
Fig. 49: Filmstrip - Offline
If an image in the filmstrip is selected it will appear in the image display with the tool graphics
showing what tools pass or fail. Above the image display, a yellow bar will appear that says
“Showing Queued Results” and the buttons at the right side of the filmstrip will become active. With
these you can scroll through the images (backward and forward), save the images in the filmstrip to
the folder setup in the settings pane or clear the filmstrip. Clicking the Continue button will return
you to configuration mode. On the left side of the filmstrip are two buttons labeled PC and Sensor.
If Sensor is selected you will be looking at images from the connected vision sensor and if PC is
selected you will be looking at images in a user selected folder on the computer.
35
Now that you have tested your application, perhaps saved some test images, made any necessary
changes to the job you are ready to deploy the system. Click on the Save Job application step (Fig.
50).
Fig. 50: Application Steps - Save Job
36
When the Save Job step is selected, the pane at the bottom of the window will change (Fig. 51)
Fig. 51: Save Job Settings
The first step would be to click the Save As… button as the job has not been previously saved. This
will open a navigation dialog to allow you to navigate to where the job is to be saved. On the left
side of the dialog you will see several icons of common places to save your job; at the bottom of this
group of icons you will see one that says In-Sight Sensors. Click this icon and open your In-
Sight 2000 from the list that appears; provide a name for the job in the appropriate field and click
Save at the bottom. Up to this point the program you created has been stored in RAM in the
vision system and by completing the above steps you have saved the job in flash memory. Had you
not done this, the first time you cycled power on the system your job file would have been lost. It is
also a good idea to save the job to your computer hard drive using the same method above (but
navigating to a directory on your hard drive) so that if something happens to the job in the vision
system you have a backup of the job.
Also in this pane you can set a Startup Job; if you have more than one job in your In-Sight 2000 this
would specify the job that would be loaded when the system power is cycled. It is always a good
idea to specify a Startup Job, even if you only have one job. Below this control is a checkbox to
Start the Sensor in Online Mode. With this checked the system will automatically start
running inspections when its power is cycled; this way you do not have to manually set it Online. At
the right side of the settings pane are two buttons, Backup and Restore. Clicking on Backup opens
a navigation dialog to save all of the files on your vision system. This saves all job files, the file that
contains your I/O settings, communication settings and any other system level settings into one file.
If your In-Sight should be compromised you will have a backup of all of the necessary files and
settings to Restore the vision system to the desired state. Clicking the Restore button will also open
a navigation dialog to allow navigation to a folder on your computer where backups would have been
saved in order to restore all job files and system settings to a vision system.
37
The final step is to run your job and inspect parts. Click the Run Job application step (Fig. 52).
Fig. 52: Application Steps - Run Job
38
When the Run Job application step is selected the pane at the bottom of the window will change.
On the left side of the pane are some controls (Fig. 53) and on the right side of the pane are results
(Fig. 54).
Fig. 53: Run Job Settings
Fig. 54: Run Job Results
In the section with the controls you can place the In-Sight 2000 Online, clear the results counters,
print the current results table, and set what is visible in the results table and image. You also see
the current inspection rate and the time taken for the current inspection.
In the results table the name of each tool is displayed, the result for the current image, the results
counters, and the time taken for each tool to run in the current image.
39
If the Options button is clicked a dialog opens that allows customization of the results table and the
image (Fig. 55).
Fig. 55: Results Display Options
On the left side of the dialog are various check boxes that specify what is displayed in the results
table. On the right side, each of the tools in the job is shown followed by check boxes to show the
tool and show the graphics. Show Tool determines if the tool is displayed in the results table. Show
Graphic determines if the tool graphics are displayed in the image when the system is online.
Your application is complete at this point.
40
In the inspection tools is a special tool that deserves its own explanation. Under the Math and Logic
Tools group is one tool, Logic (Fig. 56). To insert the tool select it from the list and click the
Add button.
Fig. 56: Logic Tool
This tool allows creating logical statements using the outputs of the inspection tools that can be tied
to discrete outputs or sent via communications. When the tool is added, the pane at the bottom of
the window will change. On the right side of this pane are the normal controls that would be seen
with any of the tools. On the left side of the pane is a list of the available tools and some buttons
(Fig. 57). The entry field below the Pass/Fail indicator by default has a “1” in it to indicate the tool is
passing. This is where a logical expression will be built.
Fig. 57: Logic Tool Settings
41
Expanding the list of the available tools exposes a pass and fail output from each (Fig. 58).
Selecting an output will enable the Insert button; clicking the Insert button will insert the selected
output into the expression field. Alternately you can double click an output to insert it.
Fig. 58: Available Tool Outputs
When an output is inserted the AND and OR buttons will be enabled; the ( and the NOT buttons are
already enabled. Clicking any of these buttons will insert the associated function into the
expression. The Insert button will become again enabled, expecting that another output will be
selected. In this manner you would build the desired expression for your application. An example of
an expression for this application is seen below (Fig. 59).
Fig. 59: Sample Logical Expression
42
Now that you understand how to use the software and have been guided through one lab it is time to
try one on your own. If you have brought in parts to test you can use those to solve an application
on your own. If not then you can build on your existing poker chip lab; complete the following steps.
1) Count the number of chip stacks on a chip

2) Count the number of white notches on the rim of the chip.
43

Cognex In-Sight 2000 Training: Provided by

Uploaded by

Copyright:

Available Formats

Cognex In-Sight 2000 Training: Provided by

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cognex In-Sight 2000 Training: Provided by

Uploaded by

Copyright:

Available Formats

Cognex In-Sight 2000 Training

Downloaded from www.Manualslib.com manuals search engine

Connecting to the IS2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Poker Chip Lab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Downloaded from www.Manualslib.com manuals search engine

Fig. 1: Application Steps - Get Connected

Fig. 2: Connected Systems

Fig. 4: Add Sensor Message Box

Fig 5: Application Steps - Set Up Image

Fig 6: Image Acquisition Settings

Fig. 7: Acquire/Load Image

Fig. 11: Image Magnification Mode

Fig 12: Application Steps - Locate Part

Fig. 13: Locate Part Tool List

Fig. 18: Palette - Results Tab

Fig. 19: Edit Tool Pane

Fig. 21: Pattern Tool Settings - Angle and Acceptance

Fig. 22: Application Steps - Inspect Part

Fig. 23: Inspect Part - Available Tools

Fig. 24: Inspect Part - Add Tool Pane

Fig. 27: Inspect Part - Pattern Settings

Fig. 28: Inspect Part - Pixel Count

Fig. 29: Pixel Count - Set Region

Fig. 30: Pixel Count - Settings

Fig. 31: Application Steps - Inputs

The following describes the various Signal Types.

Fig. 33: Application Steps - Outputs

Fig. 35: Output Details

Fig. 36: Application Steps - Communication

Fig. 37: Communication - Add Device

Fig. 38: Device Selection

Fig. 40: Communication Protocol

Fig. 42: Add Data

Fig. 43: Add FTP Image Connection

Fig. 44: Write Image FTP Settings

Fig. 46: Application Steps - Filmstrip

Fig. 48: Filmstrip - Online

Fig. 49: Filmstrip - Offline

Fig. 50: Application Steps - Save Job

Fig. 51: Save Job Settings

Fig. 52: Application Steps - Run Job

Fig. 53: Run Job Settings

Fig. 54: Run Job Results

Fig. 55: Results Display Options

Fig. 56: Logic Tool

Fig. 57: Logic Tool Settings

Fig. 58: Available Tool Outputs

Fig. 59: Sample Logical Expression

1) Count the number of chip stacks on a chip

You might also like