Original BMW Accessory.

Installation Instructions.
Universal charger/hands-free kit retrofit
BMW 5 Series Saloon (E 60)

These installation instructions are only valid for cars with SA 473 (front armrest)

Retrofit kit No. 84 64 0 307 681

Installation time
The installation time is approx. 8.0 hours, but this may vary depending on the condition of the car and
the equipment in it. The installation time will be increased by 1.0 hour on cars without SA 606/SA 609 to
install the roof aerial and by 0.75 hours on cars without joint connectors X10183 and X10184 behind
the glove compartment.
The car must be flash-upgraded with the latest I stage status before starting the conversion work. The
required programming time depends on the production date of the car and the work that has already
been carried out on it, which means that we cannot give a specific time for this work.
The time for the programming/encoding is not included in the installation time as it depends on the age
of the car and the equipment in it.

Important information
These installation instructions are primarily designed for use within the BMW dealership organisation
and by authorised BMW service companies.
In any event the target group for these installation instructions is specialist personnel trained on BMW
cars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals
and work instructions in a rational order using the prescribed tools (special tools) and observing current
health and safety regulations.
To avoid unnecessary extra work and/or costs, if any installation or function problems occur,
after a brief troubleshooting session (approx. 0.5 hours), contact the following:
1. Either your national sales company or your regional office or
2. The Support team via the Aftersales Assistance Portal (ASAP) using the optional technical
parts support application.
Quote the VIN and the part number of the retrofit kit and provide a detailed description of the
problem.
Do not archive the hard copy of these installation instructions since daily updates are made by ASAP.
See ASAP for details of the pictograms.
All the figures show LHD cars, proceed accordingly on RHD cars.
Pictograms
Denotes instructions that draw your attention to special features.

Denotes the end of the instruction or other text.

Subject to technical modifications.

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 1

Installation information
When routing fibre optic cables, make sure the bending radius is no less than 25 mm.
Before installing the roof aerial, clean and degrease the adhesion areas with conventional cleaning
products.
To ensure a permanent bond allow the car to stand in an ambient temperature of at least 20°C for
approx. four hours.
Ensure that the cables/lines are not kinked or damaged as you install them in the car. The costs incurred
as a result of this will not be reimbursed by BMW AG.
Additional cables/lines that you install must be secured with cable ties.
If the specified PIN chambers are already used, bridges, double crimps or twin-lead terminals must be
used.
After the installation work the retrofit must be programmed / coded using SSS (software service station)
via the CIP path.

Ordering instructions
Centre armrest cover O and headlining trim S or T are not included in the retrofit kit and must be ordered
separately (see EPC for part numbers and further details).

List of special equipment

The following special equipment must be taken into consideration when installing the retrofit kit:
SA 403 Glass roof
SA 606 Radio navigation system
SA 609 Navigation system

Special tools required

65 2 010, Drawing knife set

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 2

Contents

Section Page

1. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. Connection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5. To install and connect the wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6. To install and connect the ABS/DSC wiring harness

(cars without SA 606/SA 609 and without joint connectors X10183 and X10184 only) . . . . . 19

7. To install and connect the universal charger/hands-free electronic control module . . . . . . . . 20

8. To install and connect the roof aerial (cars without SA 606/SA 609 only). . . . . . . . . . . . . . . . . . 21

9. To install and connect the Bluetooth aerial and eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10. To install and connect the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

11. Concluding work and coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

12. To pair the mobile phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

13. Circuit diagram (cars built before 09/05 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

14. Circuit diagram (cars built after 09/05 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

15. Circuit diagram legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 3

1. Parts list

A AA B C D E

F G H I J

060 0404 Z

Legend

A Wiring harness
AA ABS/DSC wiring harness
(for cars without SA 606/SA 609 and without joint connectors X10183 and X10184 only)
B Roof aerial (cars without SA 606/SA 609 only)
C Hands-free microphone trim
D Eject box
E Short circuit casing
F Self-tapping screw
G Cable tie
H Telephone mounting
I Bluetooth aerial
J ULF holder

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 4

1. Parts list

K L M N O P

Q R S T U

060 0826 Z

Legend

K Universal charger/hands-free electronic control module (ULF)

L Hands-free microphone
M Hexagonal nut (4x)
N Speed nut
O Centre armrest cover (not supplied with the retrofit kit)
P Self-tapping screw, M5 x 12 (2x)
Q Hexagonal screw M5 x 14 mm (3x)
R Cable tie (30x)
S Headlining trim with SA 403 (not included in the retrofit kit)
T Headlining trim without SA 403 (not included in the retrofit kit)
U Miniature connector

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 5

2. Preparations

TIS No.
Conduct a brief test ---
Disconnect negative pole of battery 12 00 ...

The following components must be removed first of all

Boot side trim, left and right 51 47 ...
Boot floor trim 51 47 210
Rear closing panel cover 51 46 050
Rear seat and backrest side section, left, pull down the backrest 52 24 010
Headlining trim for roof aerial ---
Roof pillar trim, rear left 51 43 251
Trim at the bottom left of the door pillar 51 43 150
Door sill strips left, front and rear 51 47 ...
Lower the A pillar trim on the left 51 43 201
Front headlining trim 51 44 ...
Pedal trim 51 45 185
Oddments box on the driver’s side 51 16 ...
Driver's seat 52 ...
Audio system controller (M-ASK) 65 12 200
Centre console 51 16 200
Centre console oddments box, centre armrest cover 51 16 ...
Glove box with casing 51 16 366
Footwell trim on the right 51 45 181

Cars built before 03/05 only

Release the joint connector box on the right A pillar ---

Cars without SA 606/SA 609 and without joint connectors X10183

and X10184 behind the glove compartment only
Microfilter casing on the right 64 31 061
E box cover ---

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 6

3. Connection diagram

A3 A9
A2 A4 A5 A10
A14 A15
SA A6 A11
63
A12
44

8
6
SA

A7 A13
A1
A8

A27 A A16
A31 A22
A30 A26 A17
A28
A32 A25 A23
A18
A33 A29 A24 A20
A19 060 0397 Z

Item Designation Signal Cable colour / Connection location in the car Abbreviation
Cross-section / Slot
A Wiring harness --- --- --- ---
A1 3-pin socket casing, SW --- --- For optional aerial booster X1765
A2 Fakra plug casing, SW --- --- To branch A3 X13323
A3 Fakra socket casing, SW --- --- To branch A2 X13337
A4 Fakra plug casing, SW --- --- Tie back, not required X14233
A5 Fakra socket casing, WS --- --- To the ULF K X11575
A6 Fakra socket casing, SW --- --- Tie back, not required X13906
A7 Fakra socket casing, VI --- --- Tie back, not required X14092
A8 Fakra socket casing, BL --- --- Tie back, not required X13382
A9 Fakra socket casing, VI --- --- Tie back, not required X14093
A10 Aerial plug, VI --- --- To roof aerial B X13363
A11 Aerial plug, BL --- --- To roof aerial B X13393
A12 3-pin socket casing, SW Mic I --- To hands-free microphone L X13293
A13 6-pin socket casing, WS --- --- Tie back, not required X10686
A14 Joint connector contact DFAVL GE/RT Cars with SA 606/SA 609 only
0.35 mm 2 Insulate and tie back ---
Cars without SA 606/SA 609 and with
joint connector X10183 only
Connect to the same colours on the joint X10183
connector behind the glove compartment
Cars without SA 606/SA 609 and
without joint connector X10183 only
To branch AA3 ---

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 7

3. Connection diagram

A3 A9
A2 A4 A5 A10
A14 A15
SA A6 A11
63
A12
44

8
6
SA

A7 A13
A1
A8

A27 A A16
A31 A22
A30 A26 A17
A28
A32 A25 A23
A18
A33 A29 A24 A20
A19 060 0397 Z

Item Designation Signal Cable colour / Connection location in the car Abbreviation
Cross-section / Slot
A15 Joint connector contact DFAVR GE/WS Cars with SA 606/SA 609 only
0.35 mm2 Insulate and tie back ---
Cars without SA 606/SA 609 and with joint
connector X10184 only
Connect to the same colours on the joint connector X10184
behind the glove compartment
Cars without SA 606/SA 609 and without joint
connector X10184 only
In branch AA4 ---
A16 Joint connector contact 58G GR/RT Cars built before 03/05 only
0.35 mm2 To the joint connector behind the glove compartment X1019
Cars built after 03/05 only
To M-ASK/CCC using miniature connector U
X13812
Pin 14
A17 Socket contact TEL Crash SW/RT Cars built before 09/05 only
0.35 mm2 To 52-pin plug BR on the Safety Gateway module X13581
Cars built after 09/05 only PIN 28
To 40-pin SW plug on airbag control module
X18069
PIN 17
A18 Fibre optic cable connector MOST GN To disconnected fibre optic cable on M-ASK X13697
A19 Fibre optic cable MOST GN To the MOST output of the fibre optic cable socket X13815
casing on M-ASK PIN 2
A20 12-pin socket casing, SW Tel NF+/- --- To plug casing X13812 on M-ASK X13813
A22 Socket contact TEL Wakeup GE To the CAS control module, instrument panel, left X10318
0.35 mm2 PIN 37
A23 3-pin socket casing, VI --- --- Tie back, not required X14082

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 8

3. Connection diagram

A3 A9
A2 A4 A5 A10
A14 A15
SA A6 A11
63
A12
44

8
6
SA

A7 A13
A1
A8

A27 A A16
A31 A22
A30 A26 A17
A28
A32 A25 A23
A18
A33 A29 A24 A20
A19 060 0397 Z

Item Designation Signal Cable colour / Connection location in the car Abbreviation
Cross-section / Slot
A27 Cable eyelet 31 BR To the earth post behind the left backrest side part X13791
0.35 mm2
A24 18-pin socket casing, SW --- --- To eject box X4545
A25 Fakra plug casing, SW --- --- To eject box X13514
A26 Aerial plug, SW Ant BT --- To Bluetooth aerial under the centre armrest X11574
A28 2-pin socket casing, SW MOST --- To the ULF K X10634
A29 Socket casing, 54-pin, WS --- --- To the ULF K X695
A30 3-pin socket casing, SW --- --- Tie back, not required X14285
A31 Cable eyelet 31 BR To the earth post in the rear left wheel arch X13793
A32 Socket contact 15 GN/BR Cars built before 09/05 only X11012
0,75 mm2 To fuse holder at the rear right PIN 18
Cars built after 09/05 only
Tie back, not required ---
A33 Socket contact 30 RT/BR Cars built before 09/05 only X11015
0,75 mm2 To fuse holder at the rear right PIN 3
Cars built after 09/05 only X11012
To fuse holder at the rear right PIN 39

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 9

3. Connection diagram

AA
AA1 AA3

AA2 AA4
060 0313 Z

Item Designation Signal Cable colour / Connection location in the car Abbreviation
Cross-section / Slot
AA ABS/DSC wiring harness Cars without SA 606/SA 609 and without joint connectors
--- --- ---
X10183 X10184 only
AA1 Socket contact DFAVL GE/RT To 38-pin plug on the ABS/DSC control module X1746
0.35 mm 2 PIN 28
AA2 Socket contact DFAVR GE/WS To 38-pin plug on the ABS/DSC control module X1746
0.35 mm 2 PIN 27
AA3 Joint connector contact DFAVL GE/RT To branch A14 X10183
0.35 mm 2
AA4 Joint connector contact DFAVR GE/WS To branch A15 X10184
0.35 mm 2

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 10

4. Installation and cabling diagram

2 I D 4
1 AA
E65

3 L
B

9 7

5
K
8 6
A
060 0884 Z

Legend

A Wiring harness
AA ABS/DSC wiring harness (for cars without SA 606/SA 609 and without joint connectors X10183
and X10184 only)
B Roof aerial
D Eject box
I Bluetooth aerial
K Universal charger/hands-free electronic control module (ULF)
L Hands-free microphone

1 ABS/DSC control module

2 Joint connector A pillar right (cars built before 03/05 only)
3 Safety Gateway module (SGM)
4 Fuse holder at the rear right
5 Earth post X13793 on the rear left wheel arch
6 Earth post X13791 behind the left backrest side part
7 Airbag control module (SGM)
8 Car Access System (CAS)
9 Multi-audio system controller (M-ASK) / Car Communication Computer (CCC)

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 11

5. To install and connect the wiring harness

Cars built before 09/05 only

X11015 Route branches A32 and A33 to the fuse holder
at the rear right and secure the wiring harness A
to the existing wiring harness with cable ties R.
A Disconnect plugs X11012 and X11015 from the
fuse holder and open them.

A33
A32 R
X11012
060 0405 Z

Connect branch A32, GN/BR cable, to PIN 18 of

A33 plug X11012.
Connect branch A33, RT/BR cable, to PIN 3 of
plug X11015.

A32
X11015

X11012

060 0406 Z

Cars built after 09/05 only

Route branches A32 and A33 to the fuse holder
at the rear right and secure the wiring harness A
to the existing wiring harness with cable ties W.
Connect branch A33, RT/BR cable, to PIN 39 on
A plug X11012 and tie back branch A32, GN/BR
cable.
A33 W
A32
X11012
060 0878 Z

All cars
Secure wiring harness A to the closing panel
X13793 using cable ties (1).
1
Connect branch A31 to earth post X13793 on
the rear left wheel arch.

A
1 A31
060 0402 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 12

5. To install and connect the wiring harness

Connect branch A3 (aerial symbol) to branch A2

(SA 644).
A3 A2 Tie back branch A1 and branch A4 (SA 638),
they are not required.

A4
A1
38
SA 6

S A 644

060 0332 Z

Route branches A5-A8 and A28-A29 to the rear

left wheel arch.
Tie back branches A6, SW, A7, VI and A8, BL,
A5 not required.

A8 A6
A7
A28

A29
060 0246 Z

Connect branch A27 to earth post X13791

behind the left backrest side part.

A27

X13791
060 0237 Z

Route branches A10 – A11 to the roof aerial (1).

A10 A11
Cars with SA 606/SA 609 only
Connect branch A10, VI, to connector X13363
on the roof aerial (1) and tie back branch A11, BL,
it is not required.

X13363 1

060 0386 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 13

5. To install and connect the wiring harness

Cars built before 09/05 only

A12-A13 Route wiring harness A forwards along the
R standard wiring harness and secure it with cable
ties R.
Route branches A24-A26 to the centre armrest
and route branches A14-A23 via the centre
A14-A23 console to the front.
A
A24-A26 Route branches A12-A13 to the A pillar on the
left.

060 0334 Z

Cars built after 09/05 only

A12-A13 Route wiring harness A forwards along the
R standard wiring harness and secure it with cable
ties R.
Route branches A14-A16 and A18-A23 over
the centre console to the front and branch A17,
A14-A23 SW/RT cable, and branch A24-A26 over the
A centre console to the rear.
A17 A24-A26
Route branches A12-A13 to the A pillar on the
left.
060 0885 Z

Connect branch A17 to PIN 17 on 40-pin SW

plug X18069 on the airbag control module (1).

X18069

A17

060 0879 Z

All cars
Route branches A12-A13 to the left A pillar via
A12
the lowered headlining to the opening in the roof
trim.
A13

060 0256 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 14

5. To install and connect the wiring harness

Secure wiring harness A to the left A pillar (1)

A using a cable tie G.
1
Ensure that wiring harness A is routed and
G secured behind the head airbag.

060 0335 Z

Route branches A22 and A23 to the CAS control

module on the pedals.
Connect branch A22, GE cable, to PIN 37 of plug
X10318.
A22 A23
Tie back branch A23.

X10318
060 0235 Z

Route branch A20 to the M-ASK/CCC.

X13812 Connect branch A20 to plug casing X13812 on
X13813 the M-ASK/CCC.
If plug X13813 is already fitted, the cables
must be disconnected and connected to the
existing plug X13813.
2
- GR/VI cable to PIN 6 (1)
A20
- GR/GE cable to PIN 12 (2)

1
060 0151 Z

Route branches A18 and A19 to the M-ASK/

CCC.
A19
Unclip fibre optic cable plug X13815 from plug
X13812.
A18

X13815

X13812
060 0247 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 15

5. To install and connect the wiring harness

Disconnect the outgoing fibre optic cable from

plug X13815, PIN 2,and connect branch A19.
Clip plug X13815 into plug X13812 and connect
it to the M-ASK/CCC.

1
2

A19 X13815
060 0248 Z

Release the fibre optic cable connector X13697

on branch A18.
X13697 Connect the fibre optic cables (2) you previously
A18 disconnected.

2
060 0249 Z

Cars built before 03/05 only

A14-A16
Route branches A14-A17 under the instrument
panel to the right footwell.
Connect branch A17, SW/RT cable, to PIN 28 of
A17
the brown 52-pin plug X13581 on the Safety
Gateway module (1).

X13581

1
060 0250 Z

Connection branch A16, GR/RT cable, to the

same coloured cables on joint connector X1019
X1019 on the joint connector box (1) under the right A
1 pillar.

A16

060 0252 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 16

5. To install and connect the wiring harness

Cars built after 03/05 only

A14 A15 Route branches A14 and A15 under the
instrument panel to the right footwell.
Cars built before 09/05 only
A17
Route branch A17, SW/RT cable, under the
instrument panel to the right footwell and
X13581 connect it to PIN 28 of the brown 52-pin plug
X13581 on the Safety Gateway module (1).

1
060 0827 Z

Cars built after 03/05 only

Cut the joint connector contact off branch A16.
A16
U Use miniature connector Z to connect branch
A16, GR/RT cable, to the standard GR/RT cable
on PIN 14 of plug X13812.

X13812
061 0287 Z

Cars with SA 606/SA 609 only

X10184 X10183
Insulate and tie back branches A14 and A15.
1 Cars without SA 606/SA 609 and with joint
connectors X10183 and X10184 only
A14 Connect branches A14, GE/RT cable, and
A15 branch A15, GE/WS cable, to the same coloured
cables on joint connectors X10183 and X10184
on the joint connector box (1).

060 0254Z

Cars without SA 606/SA 609 and without

joint connectors X10183 and X10184 only

1 Connect branches A14, GE/RT cable, and

A15 branch A15, GE/WS cable, to the same coloured
cables on branches AA3 and AA4.
A14 Route branches AA1 and AA2 into the engine
compartment.
AA3
AA1-AA2 Cars built before 03/05 only
Insert branches AA3 and AA4 into the joint
AA4 connector box (1).
060 0253 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 17

5. To install and connect the wiring harness

All cars
Replace the flash adapter casing on the fibre
X13836 optic cable casing X13836 with the short circuit
casing E.

E
060 0500 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 18

6. To install and connect the ABS/DSC wiring harness (cars without SA 606/SA 609
and without joint connectors X10183 and X10184 only)

Branches AA1 and AA2 must be extended

for cars with an M57TU engine.
Route branches AA1 and AA2 along the
engine wiring harness to the ABS/DSC control
module (1) and secure it with cable ties R.
R 1 AA1-AA2 Disconnect plug X1746 from the ABS/DSC
control unit (1).

X1746
060 0336 Z

Connect branch AA1, GE/RT cable, to PIN 28 in

plug X1746.
Connect branch AA2, GE/WS cable, to PIN 27 in
plug X1746.
X1746 Connect plug X1746 to the ABS/DSC control
AA1 module.

AA2
060 0259 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 19

7. To install and connect the universal charger/hands-free electronic control module
(ULF)

Place a speed nut N on the holder (1).

N
1

060 0071 Z

Secure the ULF holder J using hexagonal

screws Q.

Q
Q

060 0260 Z

Connect branches A5, A28 and A29 to the

ULF K.
A5

A28
A29 060 0337 Z

Secure the ULF K to the ULF holder J using

hexagonal nuts M.

K M
M

J
060 0348 Z
© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 20
8. To install and connect the roof aerial (cars without SA 606/SA 609 only)

Mask the area around the roof aerial to

1 prevent damaging the paintwork.
Carefully cut the empty casing (1) for the roof
aerial off the roof with the special tool.
Clean the surfaces in the bonding areas on the
empty casing (1) and roof.

060 0310 Z

Slide in the roof aerial B at the rear (1) and secure

B it at the front with a self-tapping screw F.

1 F

060 0311 Z

Connect branch A10, VI, to connector X13363

A10 A11 and branch A11, BL, to connector X13393 on
the roof aerial B.

X13393
X13363 B

060 0255 Z

The bonding surfaces must be clean and

free of grease. The temperature of the
1 adhesive must be at least 20 °C. The har-
dening time of the adhesive is at least 4 hours.
Apply a bead of adhesive (2) around 8 mm wide
and 8 mm high to the empty casing (1).
Carefully place the empty casing (1) in its original
position, press lightly and secure it with adhesive
tape.

2
060 0312 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 21

9. To install and connect the Bluetooth aerial and eject box

Cars built before 09/05 only

Place the Bluetooth aerial I on the air duct (1) in
I the centre armrest, mark the holes and drill them
with a 2.5 mm drill bit.

060 0882 Z

All cars
P
Use self-tapping screws P to secure Bluetooth
aerial I to the air duct (1).
Connect branch A26 to the Bluetooth aerial I.
1

A26
I
060 0883 Z

Insert the eject box D into the telephone

H mounting H.

060 0339 Z

Route the cable (2) to the rear through the centre

armrest oddments tray (1)
Place the eject box with telephone mounting H in
the centre armrest oddments box (1).
H

1
2
060 0340 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 22

9. To install and connect the eject box and Bluetooth aerial

Secure the telephone mounting H in the centre

armrest oddments box (1) with fillister head
H screws (2).
2

060 0341 Z

Push the centre armrest adjustment unit (1)

O as far as forwards possible. This is only
possible when the handbrake is released.
Clip the centre armrest cover O into the centre
console.

060 0349 Z

Connect branch A24 to the plug (1) on the eject

box.
A25 Connect branch A25 to the FAKRA plug (2) in the
2 eject box.

A24 060 0342 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 23

10. To install and connect the hands-free microphone

The arrow on the hands-free microphone L

must point to the front of the car when
installed.
Clip the hands-free microphone Linto the hands-
C free microphone trim C.

060 0269 Z

Cars with SA 403 only

Unclip the sunroof button (1) from the old trim.
S
Clip the hands-free microphone trim C and the
sunroof button (1) into the headlining trim S.

C 1
060 0343 Z

Connect the plug (2) to the sunroof button (1).

1 Connect branch A12 to the hands-free

2 microphone L.
Tie back branch A13, it is not required.

A12
A13
060 0344 Z

Cars without SA 403 only

C Clip the hands-free microphone trim C into the

headlining trim T.

060 0345 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 24

10. To install and connect the hands-free microphone

Connect branch A12 to the hands-free

microphone L.
Tie back branch A13, it is not required.

A12 A13
060 0346 Z

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 25

11. Concluding work and coding

This retrofit system requires coding.

- Connect the battery
- Encode the retrofit with SSS (software service station) via the CIP path
- Conduct a brief test
- Register the mobile phone (see section 12)
- Conduct a function test
- Re-assemble the car

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 26

12. To pair the mobile phone

Setting on the car

This car is not supplied with a Bluetooth code card. The Bluetooth code required for the registration
process, an arbitrary number with up to 16 figures, can be freely selected.

- Switch on the ignition, the main menu will appear in the Control Display.
- Open the information menu >i< in the Control Display.
- Select menu point COMMUNICATION INTERFACE.
- In the Bluetooth menu select SETTINGS.
- Select and activate BLUETOOTH COMMUNICATION.
Bluetooth is indicated as activated by a check in a square.

- Select menu point TELEPHONE.

- The follow appears: BLUETOOTH CONNECTABLE IN THIS MENU.

Preparations using the mobile phone

Other work must be completed on the mobile phone and the procedures differ from model to model, see
the manual supplied with your mobile phone, for example in the following sections:
- Search for Bluetooth equipment
- Connect Bluetooth equipment
- Activate Bluetooth equipment

To conclude the registration process

- Select ADD DEVICE on the Control Display.
- Enter a freely selectable Bluetooth code using the number pad on the Control Display and confirm
your entry.
- Enter the same Bluetooth code in the mobile phone using menu point BLUETOOTH PASSKEY.
- The message HANDS-FREE ACCEPTED will appear on the mobile.
- The registration process has been completed successfully.

Notes
If the registration process was not completed successfully, switch off the ignition and repeat the entire
process rapidly.
BMW recommends that phones only be used in Original BMW snap-in adapters. This is the only way to
ensure a perfect connection via the external aerial. Otherwise poor reception may occur when using the
telephone and interference when using the audio system.

Service information
If the Bluetooth control module is replaced as part of service work, the mobile phone must be re-
registered.

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 27

 A220 A149 N38 N38 Y1*
A46

10A
7,5A

F89
F60
3 18 28 37 14 6 12 2 1
X11015 X11012

30
15
0.75 A33 0.75 A32 X13581 X10318 X13812

© BMW AG, München

RT/BR GN/BR
X13813 X13815 X13697

TEL_NF-

TEL_NF+
MOST-IN

TEL_WAKE
A19

TEL_CRASH
X1228 VB VB
A17 A22 A16 A20
30 X1438 15
A18

MOST-OUT
X1019
A16

VB
X1033 58G

0.35 0.35 0.35 0.35 0.35

0.75 0.75 GR/RT SW/RT GE GR/VI GR/GE
RT/BR RT/BR

X10634
MOST-OUT

MOST-IN

30
30
58G
X695 A28
17 18 32 15 33 41 42 1 2
A29
13. Circuit diagram (cars built before 09/05 only)

01 29 0 392 759
U400

36 54 5 6 39 10 11 3 9 29 30 46 47 48 22 32 X695

31
31
A29
X11347
VB
X11347
VB
X1033
VB 58g
0.75 0.75 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 X1228
BR BR WS/GR WS/RT WS BR/WS WS RT GE SW GN GR/GN GR/WS VB 30
X1438
VB 15

0.35 0.35 0.35 0.75 0.75 0.5

WS/BL SW GR/RT RT/BR GN/BR BR X13793
A31
X11350
VB
X11350
VB

11.2005 (Z/Z)
0.35
WS/SW X4545

SIMF_+DATA
SIMF_-DATA
SZ_2
CRADLE_ON
SIMF_CMD
SZ_1
SZ_3
SZ_4
SZ_5
SZ_6
SZ_7
HOOKSWITCH
CHARGER_ON/OFF
58G
30
15
31

X13793 A24
11 12 7 4 13 14 15 9 18 16 8 17 18 1 3 5 6 2
A31 060 0825 Z

28
 X14093 W17 X14233 W18 B400 W16
A9 A4
AU 1 AU 1

ANT
ANT
AU 1 AU 1 2 1 X13793 AU 1
X11574 X13363

© BMW AG, München

ANT

ANT
X13293 A31

ANT
X13393

MIC (-)
MIC (+)
A26 0.35 A10
A11 0.35 0.35 A12
BR/WS WS

X1228
0.35 0.75
BR RT/BR
ANT

X13337
AU 1

31
30
A3
3 2 1 AU 1
X1765 X13323
A1 0.75
A2
AU 1 AU 1 AU 1
13. Circuit diagram (cars built before 09/05 only)

0.35
WS/GE
X14092 X13382 X13906
ANT

TEL_ON

A7 A8 A6 X11575 X695
AU 1 A5 19 1 21 34 A29 AU 1 X13514

01 29 0 392 759
S A25
U400

31 50 37 38 16 53 24 25
X695 X10183 X10184
A29 0.35 0.75 AA3 AA4
X1033 GE/RT GE/WS
X13791 0.35 0.75
0.35 0.35 0.35 0.35 0.35 0.75 0.75
GE/RT GE/WS
GR GR/BL GR/RT WS/GE WS/BL WS SW
DFAVL
DFAVR

A27
0.35
DFAVL
DFAVR

58G
BR

NOTRUF_S
NOTRUF_L
LS_NOTR+
LS_NOTR-
AUX_BAT+
AUX_BAT-

31
X10183 X10184 X1746 X1746
5 4 3 2 X10686 1 2 X14082 2 1 X14285 A15 27
A14 AA1 28 AA2
A13 A23 A30

11.2005 (Z/Z)
060 0407 Z

29
 A220 A149 N38 N38 Y1*
A46

10A
F80
39 17 37 14 6 12 2 1
X11012 A32

30
15
0.75 A33 0.75 X18069 X10318 X13812

© BMW AG, München

RT/BR GN/BR
X13813 X13815 X13697

TEL_NF-

TEL_NF+
MOST-IN

TEL_WAKE
A19

TEL_CRASH
X1228 VB A17 A22 A20 A18
30

MOST-OUT
A16

VB
X1438 15 VB
X1033 58G

0.35 0.35 0.35 0.35 0.35

0.75 0.75 SW/RT GE GR/RT GR/VI GR/GE
RT/BR RT/BR

X10634
MOST-OUT

MOST-IN

30
30
58G
X695 A28
17 18 15 33 32 41 42 1 2
A29
14. Circuit diagram (cars built after 09/05 only)

01 29 0 392 759
U400

36 54 5 6 39 10 11 3 9 29 30 46 47 48 22 32 X695

31
31
A29
X11347
VB
X11347
VB
X1033
VB 58g
0.75 0.75 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 X1228
BR BR WS/GR WS/RT WS BR/WS WS RT GE SW GN GR/GN GR/WS VB 30
X1438
VB 15

0.35 0.35 0.35 0.75 0.75 0.5

WS/BL SW GR/RT RT/BR GN/BR BR X13793
A31
X11350
VB
X11350
VB

11.2005 (Z/Z)
0.35
WS/SW X4545

SIMF_+DATA
SIMF_-DATA
SZ_2
CRADLE_ON
SIMF_CMD
SZ_1
SZ_3
SZ_4
SZ_5
SZ_6
SZ_7
HOOKSWITCH
CHARGER_ON/OFF
58G
30
15
31

X13793 A24
11 12 7 4 13 14 15 9 18 16 8 17 18 1 3 5 6 2
A31 060 0877 Z

30
 X14093 W17 X14233 W18 B400 W16
A9 A4
AU 1 AU 1

ANT
ANT
AU 1 AU 1 2 1 X13793 AU 1
X11574 X13363

© BMW AG, München

ANT

ANT
X13293 A31

ANT
X13393

MIC (-)
MIC (+)
A26 0.35 A10
A11 0.35 0.35 A12
BR/WS WS

X1228
0.35 0.75
BR RT/BR
ANT

X13337
AU 1

31
30
A3
3 2 1 AU 1
X1765 X13323
A1 0.75
A2
14. Circuit diagram (cars built after 09/05 only)

AU 1 AU 1 AU 1
0.35
WS/GE
X14092 X13382 X13906
ANT

TEL_ON

A7 A8 A6 X11575 X695
AU 1 A5 19 1 21 34 A29 AU 1 X13514

01 29 0 392 759
S A25
U400

31 50 37 38 16 53 24 25
X695 X10183 X10184
A29 0.35 0.75 AA3 AA4
X1033 GE/RT GE/WS
X13791 0.35 0.75
0.35 0.35 0.35 0.35 0.35 0.75 0.75
GE/RT GE/WS
GR GR/BL GR/RT WS/GE WS/BL WS SW
DFAVL
DFAVR

A27
0.35
DFAVL
DFAVR

58G
BR

NOTRUF_S
NOTRUF_L
LS_NOTR+
LS_NOTR-
AUX_BAT+
AUX_BAT-

31
X10183 X10184 X1746 X1746
5 4 3 2 X10686 1 2 X14082 2 1 X14285 A15 27
A14 AA1 28 AA2
A13 A23 A30

11.2005 (Z/Z)
060 0407 Z

31
15. Circuit diagram legend

Legend

A46 Fuse holder at the rear right

A149 Car Access System (CAS) control module
A220 Safety Gateway module (SGM) control module/Airbag control module (SGM)

B400 Hands-free microphone

N38 Multi-audio system controller (M-ASK) / Car Communication Computer (CCC)

U400 ULF (universal charger/hands-free electronic control module)

W16 GSM roof aerial foot

W17 GPS roof aerial foot
W18 Bluetooth aerial

X695 WS 54-pin plug, to ULF

X1019 Joint connector 58G (cars built before 03/05 only)
X1033 58G connector
X1228 Connector 30
X1438 Connector 15
X1746 38-pin plug, SW, ABS/DSC control module
X1765 3-pin plug, SW; tied back
X4545 SW 18-pin plug, to eject box
X10183 Joint connector, speed signal FL
X10184 Joint connector, speed signal FR
X10318 Plug, 41-pin SW, to CAS control module
X10634 Plug, 2-pin SW, fibre optic cable to the ULF
X10686 WS 6-pin plug, tied back
X11012 32-pin SW plug, to fuse holder rear right (cars built before 09/05 only)
X11012 41-pin SW plug, to fuse holder rear right (cars built after 09/05 only)
X11015 15-pin GN plug, to fuse holder rear right (cars built before 09/05 only)
X11347 Screen connector
X11350 Screen connector
X11574 Aerial plug, SW, to Bluetooth aerial
X11575 WS aerial plug, tied back
X13293 Black 3-pin plug

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 32

15. Circuit diagram legend

Legend

X13323 Telephone aerial plug, SW, to plug X13337

X13337 Telephone aerial plug, SW, to plug X13323
X13363 Telephone aerial plug, VI, to roof aerial
X13382 BL aerial plug, tied back
X13393 GPS aerial plug, BL, to the roof aerial
X13514 Aerial plug, SW, to eject box
X13581 52-pin BR plug, to Safety Gateway module (cars built before 09/05 only)
X13697 Fibre optic cable connector
X13791 Earth post behind the left backrest side part
X13793 Rear left wheel arch earth post
X13812 16-pin SW plug (cars built after 03/05 only)
X13813 Plug, 12-pin SW, in plug X13812 on M-ASK/CCC
X13815 Plug, 2-pin SW, in plug X13812 on M-ASK/CCC
X13906 SW aerial plug, tied back
X14082 3-pin plug, VI, tied back
X14092 VI aerial plug, tied back
X14093 VI aerial plug, tied back
X14233 SW aerial plug, tied back
X14285 3-pin plug, SW; tied back
X18069 40-pin SW plug, to airbag control module (cars built after 09/05 only)

Y1* MOST connector on the car

All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.

Cable colours

BL Blue
BR Brown
GE Yellow
GN Green
GR Grey
RT Red
SW Black
VI Violet
WS White

© BMW AG, München 01 29 0 392 759 11.2005 (Z/Z) 33