Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 33 views

    Deform Pset Answers

    Uploaded by

    Uragon's gaming
    The document discusses several examples of calculating stress in mechanical engineering structures: 1) Calculating the stress in a cable supporting a 6000 lb bar attached to pins and pegs. 2) Finding the maximum load P that doesn't exceed stress limits in steel, aluminum, and bronze rods attached together. 3) Determining the maximum load P on a steel plate between a wood post and concrete that doesn't exceed stress limits in the materials. 4) Calculating the minimum plate thickness and maximum tensile stress in plates joined by a rivet.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Deform Pset Answers

    Uploaded by

    Uragon's gaming
    33 views11 pages
    The document discusses several examples of calculating stress in mechanical engineering structures: 1) Calculating the stress in a cable supporting a 6000 lb bar attached to pins and pegs. 2) Finding the maximum load P that doesn't exceed stress limits in steel, aluminum, and bronze rods attached together. 3) Determining the maximum load P on a steel plate between a wood post and concrete that doesn't exceed stress limits in the materials. 4) Calculating the minimum plate thickness and maximum tensile stress in plates joined by a rivet.

    Original Description:

    deformable bodies

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses several examples of calculating stress in mechanical engineering structures: 1) Calculating the stress in a cable supporting a 6000 lb bar attached to pins and pegs. 2) Finding the maximum load P that doesn't exceed stress limits in steel, aluminum, and bronze rods attached together. 3) Determining the maximum load P on a steel plate between a wood post and concrete that doesn't exceed stress limits in the materials. 4) Calculating the minimum plate thickness and maximum tensile stress in plates joined by a rivet.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    33 views11 pages

    Deform Pset Answers

    Uploaded by

    Uragon's gaming
    The document discusses several examples of calculating stress in mechanical engineering structures: 1) Calculating the stress in a cable supporting a 6000 lb bar attached to pins and pegs. 2) Finding the maximum load P that doesn't exceed stress limits in steel, aluminum, and bronze rods attached together. 3) Determining the maximum load P on a steel plate between a wood post and concrete that doesn't exceed stress limits in the materials. 4) Calculating the minimum plate thickness and maximum tensile stress in plates joined by a rivet.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 11

    SIMPLE STRESS

    The homogeneous bar shown in figure below is supported by a smooth pin at C and a cable that runs
    from A to B around the smooth peg at D. Find the stress in the cable if its diameter is 0.6 inch and the
    bar weighs 6000 lb.
    An aluminum rod is rigidly attached between a steel rod and a

    bronze rod as shown in figure below. Axial loads are applied at

    the positions indicated. Find the maximum value of P that will

    not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa,

    or in bronze of 100 MPa.

    A 12-inches square steel bearing plate lies between an 8-

    inches diameter wooden post and a concrete footing as

    shown in figure below. Determine the maximum value of

    the load P if the stress in wood is limited to 1800 psi and

    that in concrete to 650 psi. P = 90 478 lb

    In figure below, assume that a 20-mm-diameter rivet joins


    the plates that are each 110 mm wide. The allowable
    stresses are 120 MPa for bearing in the plate material and
    60 MPa for shearing of rivet. Determine (a) the minimum
    thickness of each plate; and (b) the largest average tensile
    stress in the plates. Ans. = 7. 85 mm; o= = 26.67 MPa
    A single rivet is used to join two plates as shown in Fig. 2-6. If the

    diameter of the rivet is 20 mm and the load P is 30 kN, what is the

    average shearing stress developed in the rivet? Ans. = 95. 5 MPa

    NOTE: GAWING 2OKN AND LOAD, 50 YUNG


    NASA SOLUTION
    THIN WALLED

    The wall thickness of a 4-ft-diameter spherical tank is 5/16 in.

    Calculate the allowable internal pressure if the stress is limited to

    8000 psi. Ans. P = 208. 3327 psi

    A cylindrical pressure vessel is fabricated from steel plating that

    has a thickness of 20 mm. The diameter of the pressure vessel is

    450 mm and its length is 2.0 m. Determine the maximum internal

    pressure that can be applied if the longitudinal stress is limited to

    140 MPa, and the circumferential stress is limited to 60 MPa. Ans.

    P = 5. 3345 MPa

    The strength of longitudinal joint in figure below is 33 kips/ft,

    whereas for the girth is 16 kips/ft. Calculate the maximum

    diameter of the cylinder tank if the internal pressure is 150 psi.

    Ans. P = 35. 5615 MPa


    The strength of longitudinal joint in figure below is 33 kips/ft,

    whereas for the girth is 16 kips/ft. Calculate the maximum

    diameter of the cylinder tank if the internal pressure is 150 psi.

    Ans. P = 35. 5615 MPa

    STATICALLY INDETERMINATE MEMBERS


    NOTE: NATYPO ATA ANG SR SA ANSWER NYA,
    LAHAT NG SAGOT SA ET AY 22.48 CHECK NYO PA DIN
    KUNG TAMA TALAGANG 22.48 O TAMA ANG SR

    You might also like