Low Impedance Bus Differential System: Grid Solutions

GE
Grid Solutions
B90
Low Impedance Bus Differential
System
Instruction Manual
Product version: 7.7x
GE publication code: 1601-0115-AG2 (GEK-131031A)
E83849
S T ER
GI
ED
RE
ISO 9001
LISTED
G
E
IN
M U LT I L
IND.CONT. EQ.
52TL
1601-0115-AG2
Copyright © 2018 GE Multilin Inc. All rights reserved.
B90 Low Impedance Bus Differential System Instruction Manual for version 7.7x.
B90, FlexLogic, FlexElement, FlexCurve, FlexAnalog, FlexInteger, FlexState, EnerVista,
CyberSentry, HardFiber, Multilin, and GE Multilin are trademarks or registered trademarks
of GE Multilin Inc.
The contents of this manual are the property of GE Multilin Inc. This documentation is
furnished on license and may not be reproduced in whole or in part without the permission
of GE Multilin. The content of this manual is for informational use only and is subject to
change without notice.
Part number: 1601-0115-AG2 (May 2018)
B90 Low Impedance Bus Differential System
Table of contents
1 INTRODUCTION 1.1 Safety symbols and definitions ........................................................................... 1-1

1.1.1 General cautions and warnings .................................................................................... 1-1
1.2 For further assistance........................................................................................... 1-2
2 PRODUCT 2.1 Product description ............................................................................................... 2-1

DESCRIPTION 2.2 Security .................................................................................................................... 2-4
2.3 Order codes............................................................................................................. 2-8
2.3.1 Replacement modules .....................................................................................................2-12
2.4 Signal processing ................................................................................................. 2-13
2.4.1 UR signal processing ........................................................................................................2-13
2.5 Specifications........................................................................................................ 2-15
2.5.1 Protection elements ..........................................................................................................2-16
2.5.2 User-programmable elements ....................................................................................2-17
2.5.3 Monitoring..............................................................................................................................2-18
2.5.4 Metering..................................................................................................................................2-19
2.5.5 Inputs .......................................................................................................................................2-19
2.5.6 Power supply ........................................................................................................................2-20
2.5.7 Outputs....................................................................................................................................2-21
2.5.8 Communications ................................................................................................................2-23
2.5.9 Inter-relay communications..........................................................................................2-24
2.5.10 CyberSentry security.........................................................................................................2-25
2.5.11 Graphical front panel........................................................................................................2-25
2.5.12 Environmental......................................................................................................................2-26
2.5.13 Type tests ...............................................................................................................................2-27
2.5.14 Production tests ..................................................................................................................2-27
2.5.15 Approvals ...............................................................................................................................2-28
2.5.16 Maintenance.........................................................................................................................2-28
3 INSTALLATION 3.1 Unpack and inspect ............................................................................................... 3-1

3.2 Panel cutouts .......................................................................................................... 3-2
3.2.1 Rear terminal layout ........................................................................................................... 3-6
3.3 Wiring..................................................................................................................... 3-10
3.3.1 Typical wiring .......................................................................................................................3-10
3.3.2 Dielectric strength..............................................................................................................3-16
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL iii

TABLE OF CONTENTS
3.3.3 Control power ...................................................................................................................... 3-16

3.3.4 CT and VT modules............................................................................................................ 3-17
3.3.5 Contact inputs and outputs .......................................................................................... 3-18
3.3.6 RS232 port............................................................................................................................. 3-30
3.3.7 CPU communication ports ............................................................................................ 3-31
3.3.8 IRIG-B....................................................................................................................................... 3-33
3.4 Direct input and output communications .......................................................3-34
3.4.1
Description ............................................................................................................................ 3-34
3.4.2
Fiber: LED and ELED transmitters............................................................................... 3-37
3.4.3
Fiber laser transmitters................................................................................................... 3-37
3.4.4
G.703 interface.................................................................................................................... 3-38
3.4.5
RS422 interface................................................................................................................... 3-42
3.4.6
RS422 and fiber interface .............................................................................................. 3-44
3.4.7
G.703 and fiber interface................................................................................................ 3-45
3.4.8
IEEE C37.94 interface ....................................................................................................... 3-45
3.4.9
C37.94SM interface........................................................................................................... 3-48
3.5 Activate relay ........................................................................................................3-51
3.6 Install software .....................................................................................................3-52
3.6.1 EnerVista communication overview ......................................................................... 3-52
3.6.2 System requirements....................................................................................................... 3-53
3.6.3 Install software.................................................................................................................... 3-54
3.7 Add device to software........................................................................................3-55
3.7.1 Set IP address in UR.......................................................................................................... 3-56
3.7.2 Configure serial connection.......................................................................................... 3-62
3.7.3 Configure Ethernet connection ................................................................................... 3-63
3.7.4 Configure modem connection.....................................................................................3-64
3.7.5 Automatic discovery of UR devices........................................................................... 3-65
3.8 Connect to the B90...............................................................................................3-66
3.8.1 Connect to the B90 in EnerVista ................................................................................. 3-66
3.8.2 Use Quick Connect via front RS232 port................................................................. 3-67
3.8.3 Use Quick Connect via front USB port ..................................................................... 3-68
3.8.4 Use Quick Connect via a rear Ethernet port.......................................................... 3-68
3.9 Set up CyberSentry and change default password........................................3-69
3.10 Import settings .....................................................................................................3-70
3.11 Connect to D400 gateway...................................................................................3-71
3.11.1 Oscillography files.............................................................................................................. 3-71
3.11.2 Event records ....................................................................................................................... 3-71
3.11.3 Log files................................................................................................................................... 3-71
3.11.4 Setting files............................................................................................................................ 3-72
4 INTERFACES 4.1 EnerVista software interface................................................................................4-1

4.1.1 Introduction .............................................................................................................................4-1
4.1.2 Settings files ............................................................................................................................4-1
4.1.3 Event viewing..........................................................................................................................4-2
4.1.4 File support ..............................................................................................................................4-3
4.1.5 EnerVista main window .....................................................................................................4-3
4.1.6 Protection summary window..........................................................................................4-4
4.1.7 Settings templates................................................................................................................4-5
4.1.8 Secure and lock FlexLogic equations ..........................................................................4-9
4.1.9 Settings file traceability................................................................................................... 4-12
4.2 Front panel interface ...........................................................................................4-15
4.2.1 Front panel............................................................................................................................ 4-15
4.2.2 Front panel display............................................................................................................ 4-17
4.2.3 Front panel navigation keys ......................................................................................... 4-37
4.2.4 LED indicators...................................................................................................................... 4-38
iv B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

TABLE OF CONTENTS
4.2.5 Front panel labelling .........................................................................................................4-42

4.2.6 Menu navigation.................................................................................................................4-49
4.2.7 Change settings ..................................................................................................................4-51
4.2.8 View actual values.............................................................................................................4-56
4.2.9 Change passwords............................................................................................................4-57
4.2.10 Invalid password entry ....................................................................................................4-58
4.3 Logic diagrams ..................................................................................................... 4-58
4.4 FlexLogic design using Engineer ....................................................................... 4-59
4.4.1 Design logic...........................................................................................................................4-61
4.4.2 Send file to and from device .........................................................................................4-72
4.4.3 Monitor logic.........................................................................................................................4-73
4.4.4 View front panel and print labels................................................................................4-74
4.4.5 Generate connectivity report........................................................................................4-75
4.4.6 Preferences ...........................................................................................................................4-75
4.4.7 Toolbars ..................................................................................................................................4-79
5 SETTINGS 5.1 Settings menu......................................................................................................... 5-1

5.2 Overview.................................................................................................................. 5-3
5.2.1 Introduction to elements .................................................................................................. 5-3
5.3 Product setup.......................................................................................................... 5-5
5.3.1 B90 function............................................................................................................................ 5-5
5.3.2 Security ..................................................................................................................................... 5-5
5.3.3 Display properties ..............................................................................................................5-23
5.3.4 Graphical front panel........................................................................................................5-25
5.3.5 Clear relay records.............................................................................................................5-36
5.3.6 Communications ................................................................................................................5-37
5.3.7 Modbus user map ........................................................................................................... 5-100
5.3.8 Real-time clock.................................................................................................................5-100
5.3.9 User-programmable fault report.............................................................................5-106
5.3.10 Oscillography.....................................................................................................................5-106
5.3.11 User-programmable LEDs ..........................................................................................5-109
5.3.12 User-programmable self-tests .................................................................................5-113
5.3.13 Control pushbuttons ...................................................................................................... 5-114
5.3.14 User-programmable pushbuttons ..........................................................................5-115
5.3.15 Flex state parameters ...................................................................................................5-121
5.3.16 User-definable displays................................................................................................5-122
5.3.17 Direct inputs and outputs............................................................................................5-124
5.3.18 Installation ..........................................................................................................................5-130
5.4 System setup.......................................................................................................5-131
5.4.1 AC inputs .............................................................................................................................5-131
5.4.2 Power system....................................................................................................................5-131
5.4.3 FlexCurves...........................................................................................................................5-132
5.4.4 Bus..........................................................................................................................................5-139
5.5 FlexLogic ..............................................................................................................5-141
5.5.1 FlexLogic operands ........................................................................................................ 5-141
5.5.2 FlexLogic rules ..................................................................................................................5-149
5.5.3 FlexLogic evaluation ...................................................................................................... 5-149
5.5.4 FlexLogic example ..........................................................................................................5-150
5.5.5 FlexLogic equation editor ............................................................................................5-155
5.5.6 FlexLogic timers ...............................................................................................................5-155
5.5.7 Non-volatile latches .......................................................................................................5-155
5.6 Grouped elements..............................................................................................5-156
5.6.1 Overview..............................................................................................................................5-156
5.6.2 Setting group 1.................................................................................................................5-156
5.6.3 Bus differential..................................................................................................................5-157
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL v

TABLE OF CONTENTS
5.6.4 Breaker failure (ANSI 50BF)......................................................................................... 5-162

5.6.5 Voltage elements ............................................................................................................ 5-170
5.6.6 Current elements ............................................................................................................ 5-171
5.6.7 End fault protection ....................................................................................................... 5-178
5.7 Control elements ............................................................................................... 5-180
5.7.1
Overview ............................................................................................................................. 5-180
5.7.2
Trip bus ................................................................................................................................ 5-181
5.7.3
Setting groups .................................................................................................................. 5-183
5.7.4
Digital elements............................................................................................................... 5-184
5.7.5
Monitoring elements ..................................................................................................... 5-187
5.8 Inputs/outputs ................................................................................................... 5-192
5.8.1 Contact inputs .................................................................................................................. 5-192
5.8.2 Virtual inputs ..................................................................................................................... 5-194
5.8.3 Contact outputs............................................................................................................... 5-195
5.8.4 Virtual outputs.................................................................................................................. 5-199
5.8.5 Resetting ............................................................................................................................. 5-199
5.8.6 Direct inputs and outputs ........................................................................................... 5-200
5.9 Testing ................................................................................................................. 5-204
5.9.1 Test mode function ........................................................................................................ 5-204
5.9.2 Test mode forcing........................................................................................................... 5-205
5.9.3 Force contact inputs ..................................................................................................... 5-205
5.9.4 Force contact outputs .................................................................................................. 5-206
5.10 Simulation ........................................................................................................... 5-207
5.10.1 GOOSE .................................................................................................................................. 5-207
6 ACTUAL VALUES 6.1 Actual Values menu ...............................................................................................6-1

6.2 Front panel...............................................................................................................6-2
6.2.1 Enhanced and basic front panels .................................................................................6-2
6.2.2 Graphical front panel ..........................................................................................................6-3
6.3 Status........................................................................................................................6-4
6.3.1 Contact inputs ........................................................................................................................6-4
6.3.2 Virtual inputs ...........................................................................................................................6-4
6.3.3 RxGOOSE boolean inputs ..................................................................................................6-4
6.3.4 RxGOOSE DPS inputs...........................................................................................................6-4
6.3.5 Contact outputs.....................................................................................................................6-5
6.3.6 Virtual outputs........................................................................................................................6-5
6.3.7 RxGOOSE status.....................................................................................................................6-5
6.3.8 RxGOOSE statistics ...............................................................................................................6-6
6.3.9 Flex States ................................................................................................................................6-6
6.3.10 Ethernet .....................................................................................................................................6-6
6.3.11 Real time clock synchronizing.........................................................................................6-7
6.3.12 Direct inputs ............................................................................................................................6-7
6.3.13 Direct devices status ...........................................................................................................6-8
6.3.14 Remaining connection status .........................................................................................6-8
6.3.15 Parallel Redundancy Protocol (PRP) .............................................................................6-9
6.3.16 TxGOOSE status .....................................................................................................................6-9
6.3.17 Protocol................................................................................................................................... 6-10
6.4 Metering .................................................................................................................6-10
6.4.1 Metering conventions ...................................................................................................... 6-10
6.4.2 Bus zone................................................................................................................................. 6-11
6.4.3 Currents.................................................................................................................................. 6-11
6.4.4 Voltages.................................................................................................................................. 6-12
6.4.5 Frequency.............................................................................................................................. 6-12
6.4.6 RxGOOSE analogs.............................................................................................................. 6-12
6.5 Records...................................................................................................................6-12
vi B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

TABLE OF CONTENTS
6.5.1 User-programmable fault reports..............................................................................6-12

6.5.2 Event records .......................................................................................................................6-13
6.5.3 Oscillography........................................................................................................................6-14
6.6 Product information ............................................................................................ 6-15
6.6.1 Model information..............................................................................................................6-15
6.6.2 Firmware revisions ............................................................................................................6-16
7 COMMANDS AND 7.1 Commands menu ................................................................................................... 7-1

TARGETS 7.1.1 Virtual inputs........................................................................................................................... 7-2
7.1.2 Clear records .......................................................................................................................... 7-2
7.1.3 Set date and time................................................................................................................. 7-2
7.1.4 Relay maintenance.............................................................................................................. 7-3
7.1.5 Security ..................................................................................................................................... 7-4
7.2 Targets menu.......................................................................................................... 7-4
7.2.1 Target messages .................................................................................................................. 7-5
7.2.2 Relay self-tests ...................................................................................................................... 7-5
8 APPLICATION OF 8.1 Overview.................................................................................................................. 8-1

SETTINGS 8.1.1 Introduction............................................................................................................................. 8-1
8.1.2 Sample busbar and data .................................................................................................. 8-1
8.2 Zoning and dynamic bus replica ......................................................................... 8-3
8.2.1 North bus zone ...................................................................................................................... 8-3
8.2.2 South bus zone...................................................................................................................... 8-4
8.3 Biased characteristic breakpoints...................................................................... 8-5
8.3.1 Description .............................................................................................................................. 8-5
8.3.2 High breakpoint .................................................................................................................... 8-5
8.3.3 Low breakpoint...................................................................................................................... 8-6
8.4 Slopes and high set threshold ............................................................................. 8-6
8.4.1 Description .............................................................................................................................. 8-6
8.4.2 External faults on C-1......................................................................................................... 8-7
8.4.5 External faults on C-4.......................................................................................................8-10
8.4.6 External faults on C-5.......................................................................................................8-10
8.5 Bus differential settings...................................................................................... 8-10
8.5.1 Description ............................................................................................................................8-10
8.6 Enhancing relay performance ........................................................................... 8-11
8.6.1 Using setting groups.........................................................................................................8-11
9 THEORY OF 9.1 Introduction ............................................................................................................ 9-1

OPERATION 9.1.1 Bus differential protection................................................................................................ 9-1
9.2 Dynamic bus replica .............................................................................................. 9-3
9.2.1 Dynamic bus replica mechanism ................................................................................. 9-3
9.2.2 CT ratio matching................................................................................................................. 9-3
9.3 Differential principle.............................................................................................. 9-3
9.3.1 Biased differential characteristic .................................................................................. 9-3
9.3.2 Differential and restraining currents........................................................................... 9-4
9.3.3 Enhanced security ............................................................................................................... 9-5
9.4 Directional principle .............................................................................................. 9-6
9.4.1 Current directional protection........................................................................................ 9-6
9.5 Saturation detector ............................................................................................... 9-7
9.5.1 CT saturation detection..................................................................................................... 9-7
9.6 Output logic and examples .................................................................................. 9-9
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL vii

TABLE OF CONTENTS
9.6.1 Output logic .............................................................................................................................9-9

9.6.2 Internal and external fault example ......................................................................... 9-10
10 MAINTENANCE 10.1 Monitoring .............................................................................................................10-1

10.1.1 Devices with Site Targets ............................................................................................... 10-1
10.1.2 Data with Modbus Analyzer.......................................................................................... 10-1
10.2 General maintenance ..........................................................................................10-3
10.2.1 In-service maintenance.................................................................................................. 10-3
10.2.2 Out-of-service maintenance ........................................................................................ 10-3
10.2.3 Unscheduled maintenance (system interruption) .............................................. 10-3
10.3 Retrieve files ..........................................................................................................10-3
10.3.1 CyberSentry security event files.................................................................................. 10-4
10.4 Convert device settings.......................................................................................10-5
10.5 Copy settings to other device ............................................................................10-7
10.6 Compare settings .................................................................................................10-7
10.6.1 Compare against defaults ............................................................................................. 10-7
10.6.2 Compare two devices ...................................................................................................... 10-8
10.7 Back up and restore settings .............................................................................10-8
10.7.1 Back up settings .................................................................................................................10-8
10.7.2 Restore settings ............................................................................................................... 10-11
10.8 Upgrade software.............................................................................................. 10-13
10.9 Upgrade firmware ............................................................................................. 10-14
10.10 Replace front panel ........................................................................................... 10-15
10.11 Replace module ................................................................................................. 10-23
10.12 Battery................................................................................................................. 10-25
10.12.1 Replace battery................................................................................................................ 10-25
10.12.2 Dispose of battery .......................................................................................................... 10-26
10.13 Clear files and data after uninstall ................................................................ 10-29
10.14 Repairs................................................................................................................. 10-30
10.15 Storage ................................................................................................................ 10-30
10.16 Disposal............................................................................................................... 10-31
A FLEXANALOG A.1 FlexAnalog items ................................................................................................... A-1

OPERANDS
B RADIUS SERVER B.1 RADIUS server configuration ................................................................................B-1

CONFIGURATION
C COMMAND LINE C.1 Command line interface ....................................................................................... C-1

INTERFACE
D MISCELLANEOUS D.1 Warranty ................................................................................................................. D-1

D.2 Revision history ..................................................................................................... D-1
ABBREVIATIONS
INDEX
viii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Chapter 1: Introduction
Introduction
This chapter outlines safety and technical support information.
1.1 Safety symbols and definitions

Before attempting to install or use the device, review all safety indicators in this document to help prevent injury,
equipment damage, or downtime.
The following safety and equipment symbols are used in this document.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Indicates practices not related to personal injury.
1.1.1 General cautions and warnings

The following general safety precautions and warnings apply.
Ensure that all connections to the product are correct so as to avoid accidental risk of shock
and/or fire, for example such as can arise from high voltage connected to low voltage terminals.
Follow the requirements of this manual, including adequate wiring size and type, terminal torque settings, voltage,
current magnitudes applied, and adequate isolation/clearance in external wiring from high to low voltage circuits.
Use the device only for its intended purpose and application.
Ensure that all ground paths are uncompromised for safety purposes during device operation and service.
Ensure that the control power applied to the device, the alternating current (AC), and voltage input match the ratings
specified on the relay nameplate. Do not apply current or voltage in excess of the specified limits.
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 1-1

FOR FURTHER ASSISTANCE CHAPTER 1: INTRODUCTION
Only qualified personnel are to operate the device. Such personnel must be thoroughly familiar with all safety
cautions and warnings in this manual and with applicable country, regional, utility, and plant safety regulations.
1 Hazardous voltages can exist in the power supply and at the device connection to current transformers, voltage
transformers, control, and test circuit terminals. Make sure all sources of such voltages are isolated prior to
attempting work on the device.
Hazardous voltages can exist when opening the secondary circuits of live current transformers. Make sure that
current transformer secondary circuits are shorted out before making or removing any connection to the current
transformer (CT) input terminals of the device.
For tests with secondary test equipment, ensure that no other sources of voltages or currents are connected to such
equipment and that trip and close commands to the circuit breakers or other switching apparatus are isolated,
unless this is required by the test procedure and is specified by appropriate utility/plant procedure.
When the device is used to control primary equipment, such as circuit breakers, isolators, and other switching
apparatus, all control circuits from the device to the primary equipment must be isolated while personnel are working
on or around this primary equipment to prevent any inadvertent command from this device.
Use an external disconnect to isolate the mains voltage supply.
Personal safety can be affected if the product is physically modified by the end user. Modifications to the product
outside of recommended wiring configuration, hardware, or programming boundaries is not recommended end-use
practice. Product disassembly and repairs are not permitted. All service needs to be conducted by the factory.
LED transmitters are classified as IEC 60825-1 Accessible Emission Limit (AEL) Class 1M. Class 1M
devices are considered safe to the unaided eye. Do not view directly with optical instruments.
This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial
environments. Not to be used near electronic devices rated for Class B levels.
1.2 For further assistance

For product support, contact the information and call center as follows:
GE Grid Solutions
650 Markland Street
Markham, Ontario
Canada L6C 0M1
Worldwide telephone: +1 905 927 7070
Europe/Middle East/Africa telephone: +34 94 485 88 54
North America toll-free: 1 800 547 8629
Fax: +1 905 927 5098
Worldwide e-mail: multilin.tech@ge.com
Europe e-mail: multilin.tech.euro@ge.com
Website: http://www.gegridsolutions.com/multilin
When contacting GE by e-mail, optionally include a device information file, which is generated in the EnerVista software by
clicking the Service Report button. The service report also can be generated in the field, for example with a USB cable
connected between the graphical front panel and a computer, and the Device Setup configured for the USB connection.
1-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

CHAPTER 1: INTRODUCTION FOR FURTHER ASSISTANCE
Figure 1-1: Generate service report in EnerVista software

FOR FURTHER ASSISTANCE CHAPTER 1: INTRODUCTION

Chapter 2: Product description
Product description
This chapter outlines the product, order codes, and specifications.
2.1 Product description

The B90 Low Impedance Bus Differential System is a microprocessor-based architecture that provides protection and
metering for busbars with up to 24 feeders. The B90 protection system is a centralized architecture built on one B90 IED as
per requirements of a particular application. The IED is a full-featured B90 and as such can be accessed and programmed
individually. Protection and supervisory functions of the B90 include:
• Multi-zone differential protection with both restrained (percent, biased) and unrestrained (unbiased, instantaneous)
functions incorporated. Differential protection is fast (typical response time: ¾ of a power cycle; maximum response
time: 1 power cycle) and secure. Security is achieved by using fast and reliable CT saturation detection algorithm and
a second, phase comparison operating principle.
• Check-zone functionality is provided by programming one of the differential zones to enclose the entire bus
• Dynamic bus replica functionality and multi-zone protection allowing application of the B90 to multi-section re-
configurable busbars
• Isolator monitoring feature monitors up to 48 isolators from the B90 IED
• End fault protection (dead zone protection) is provided for up to 24 breakers
• CT trouble monitoring function is provided for each zone of differential protection
• Breaker fail function is provided for up to 24 breakers
• An instantaneous overcurrent function is available per each current input of the B90 system
• A time overcurrent function is available per each current input of the B90 system for backup protection
• An undervoltage function is provided per each voltage input of the B90 system for supervision purposes
Voltage and current metering is built into the relay as a standard feature. Current parameters are available as total
waveform RMS magnitude, or as fundamental frequency only RMS magnitude and angle (phasor).
Diagnostic features include an event recorder capable of storing 1024 time-tagged events and oscillography capable of
storing up to 64 records with programmable trigger, content, and sampling rate. The internal clock used for time-tagging
can be synchronized with an IRIG-B signal, using the Simple Network Time Protocol (SNTP) over the Ethernet port, or using
the Precision Time Protocol (PTP). This precise time stamping allows the sequence of events to be determined between the
B90 IEDs and throughout the system. Events can also be programmed (via FlexLogic™ equations) to trigger oscillography
data capture that can be set to record the measured parameters before and after the event for viewing on a computer.
These tools significantly reduce troubleshooting time and simplify report generation in the event of a system fault.

PRODUCT DESCRIPTION CHAPTER 2: PRODUCT DESCRIPTION
Several options are available for communication. An RS232 port (USB port with the graphical front panel) can be used to
connect to a computer for the programming of settings and the monitoring of actual values. The rear RS485 port allows
independent access by operating and engineering staff. It can be connected to system computers with baud rates up to
115.2 kbps. All serial ports use the Modbus RTU protocol. The IEC 60870-5-103 protocol is supported on the RS485
interface. IEC 60870-5-103, DNP, and Modbus cannot be enabled simultaneously on this interface. Also only one of the
DNP, IEC 60870-5-103, and IEC 60870-5-104 protocols can be enabled at any time on the relay. When the IEC 60870-5-103
protocol is chosen, the RS485 port has a fixed even parity and the baud rate can be either 9.6 kbps or 19.2 kbps. The
100Base-FX or 100Base-TX Ethernet interface provides fast, reliable communications in noisy environments. The Ethernet
2 port supports IEC 61850, Modbus/TCP, TFTP, and PTP (according to IEEE Std. 1588-2008 or IEC 61588), and it allows access
to the relay via any standard web browser (B90 web pages). The IEC 60870-5-104 protocol is supported on the Ethernet
port. The Ethernet port also supports the Parallel Redundancy Protocol (PRP) of IEC 62439-3 (clause 4, 2012) when
purchased as an option.
Secure Routable GOOSE (R-GOOSE) is supported with software options.
Settings and actual values can be accessed from the front panel or EnerVista software.
The B90 uses flash memory technology that allows field upgrading as new features are added. Firmware and software are
upgradable.
The following single-line diagram illustrates the relay functionality using American National Standards Institute (ANSI)
device numbers.
The available zones of differential protection and their size (maximum number of inputs) are optional and
controlled by the software option portion of the order code. The breaker failure function is also optional. See
the ordering section for information on the maximum number of zones and inputs for a given model. In
addition, different applications can require differing numbers of B90s with different hardware configurations.
Table 2-1: ANSI device numbers and functions supported
Device Function Device Function
number number
27 Undervoltage 51 Time overcurrent
50 Instantaneous overcurrent 50BF Breaker failure
50/74 CT trouble 50EF End fault protection
50/87 Unrestrained bus differential

CHAPTER 2: PRODUCT DESCRIPTION PRODUCT DESCRIPTION
Figure 2-1: Single-line diagram
Isolator position
Breaker position and trip
50 27 50 50 27 50
and dynamic bus replica

Isolator monitoring
51 51 51 51
50BF 50BF 50BF 50BF
50EF 50EF 50EF 50EF
Zone 1
voltage, and frequency

Metering: current,
87B 50/87 50/74
Zone 2
87B 50/87 50/74
Zone 3
87B 50/87 50/74
Zone 4
87B 50/87 50/74

836752A5.CDR
Table 2-2: Other device functions

Function Function
Contact inputs (up to 120 per IED) Modbus communications
Contact outputs (up to 72 per IED) Modbus user map
Control pushbuttons Non-volatile latches
CyberSentry™ security Oscillography
Digital elements (48 per IED) Setting groups (6)
Direct inputs and outputs (256) Time synchronization over IRIG-B or IEEE 1588
DNP 3.0 or IEC 60870-5-104 communications Time synchronization over SNTP
Dynamic bus replica User definable displays
End fault protection User-programmable fault reports
Event recorder User-programmable LEDs

SECURITY CHAPTER 2: PRODUCT DESCRIPTION
Function Function
IEC 60870-5-103 communications User-programmable pushbuttons
FlexLogic equations User-programmable self-tests
IEC 61850 communications Virtual inputs (64 per IED)
IEC 62351-9 data and communications security Virtual outputs (96 per IED)
Metering: current, voltage, frequency
2
2.2 Security
The following security features are available:
• Password security — Basic security present by default
• EnerVista security — Role-based access to various EnerVista software screens and configuration elements. The
feature is present by default in the EnerVista software.
• CyberSentry security — Advanced security available using a software option. When purchased, the option is enabled
automatically, and the default Password security and EnerVista security are disabled.
2.2.0.1 EnerVista security

The EnerVista security management system is a role-based access control (RBAC) system that allows an administrator to
manage the privileges of multiple users. This allows for access control of UR devices by multiple personnel within a
substation and conforms to the principles of RBAC as defined in ANSI INCITS 359-2004. The EnerVista security
management system is disabled by default to allow the administrator direct access to the EnerVista software after
installation. It is recommended that security be enabled before placing the device in service.
Basic password or enhanced CyberSentry security applies, depending on purchase.
2.2.0.2 Password security

Password security is a basic security feature present by default.
Two levels of password security are provided: command and setting. Use of a password for each level controls whether all
users can enter commands and/or change settings.
Two types of connection security are provided: password entry from local or remote connection. Local access is defined as
access to settings or commands via the front panel interface. This includes both keypad entry and the through a front
panel port. Remote access is defined as access to settings or commands via any rear communications port. This includes
both Ethernet and RS485 connections. These two settings are on by default and apply to all users.
When entering a settings or command password via EnerVista or any serial interface, the user must enter the
corresponding connection password. If the connection is to the back of the B90, the remote password is used. If the
connection is to a front panel port, the local password applies. (These two local and remote password settings are not
shown the figure.)
Password access events are logged in the Event Recorder.

CHAPTER 2: PRODUCT DESCRIPTION SECURITY
Figure 2-2: Access control by passwords and connection type
2.2.0.3 CyberSentry security

CyberSentry security is available using software options that provide advanced security. When the option is purchased, the
basic password security is disabled automatically.
CyberSentry provides security through the following features:
• An Authentication, Authorization, Accounting (AAA) Remote Authentication Dial-In User Service (RADIUS) client that is
managed centrally, enables user attribution, provides accounting of all user activities, and uses secure standards-
based strong cryptography for authentication and credential protection. In other words, this option uses a RADIUS
server for user authentication.
• A Role-Based Access Control (RBAC) system that provides a permission model that allows access to UR device
operations and configurations based on specific roles and individual user accounts configured on the AAA server.
That is, Administrator, Supervisor, Engineer, Operator, and Observer roles are used.
• Security event reporting through the Syslog protocol for supporting Security Information Event Management (SIEM)
systems for centralized cybersecurity monitoring
• Strong encryption of all access and configuration network messages between the EnerVista software and UR devices
using the Secure Shell (SSH) protocol, the Advanced Encryption Standard (AES), and 128-bit keys in Galois Counter
Mode (GCM) as specified in the U.S. National Security Agency Suite B extension for SSH and approved by the National
Institute of Standards and Technology (NIST) FIPS-140-2 standards for cryptographic systems
CyberSentry user roles

CyberSentry user roles (Administrator, Supervisor, Engineer, Operator, Observer) limit the levels of access to various UR
functions. This means that the EnerVista software allows for access to functionality based on the user’s logged in role.
Example: Administrative functions can be segmented from common operator functions, or engineering type access, all of
which are defined by separate roles so that access of UR devices by multiple personnel within a substation is allowed.
One role of one type is allowed to be logged in at a time. For example, one Operator can be logged in but not a second
Operator at the same time. This prevents subsets of settings from being changed at the same time.

SECURITY CHAPTER 2: PRODUCT DESCRIPTION
Figure 2-3: CyberSentry user roles
Administrator
Engineer
Operator
2 Observer Supervisor
842838A2.CDR
The table lists user roles and permissions.
Table 2-3: Permissions by user role with CyberSentry

Administrator Engineer Operator Supervisor Observer
Summary Complete access Complete access Command Authorizes Default role
except for menu writing
CyberSentry
Security
Device Definition R R R R R
Settings
|---------- Product Setup
|--------------- Security RW R R R R
(CyberSentry)
|--------------- Supervisory See table notes R R See table R
notes
|--------------- Display Properties RW RW R R R
|--------------- Clear Relay Records RW RW R R R
(settings)
|--------------- Communications RW RW R R R
|--------------- Modbus User Map RW RW R R R
|--------------- Real Time Clock RW RW R R R
|--------------- Oscillography RW RW R R R
|--------------- Data Logger RW RW R R R
|--------------- Demand RW RW R R R
|--------------- User-Programmable RW RW R R R
LEDs
Self Tests
|--------------- Control Pushbuttons RW RW R R R
Pushbuttons
|--------------- Flex state RW RW R R R
Parameters
|--------------- User-Definable RW RW R R R
Displays
|--------------- Direct I/O RW RW R R R
|--------------- Teleprotection RW RW R R R
|--------------- Installation RW RW R R R
|---------- System Setup RW RW R R R

CHAPTER 2: PRODUCT DESCRIPTION SECURITY
Administrator Engineer Operator Supervisor Observer

|---------- FlexLogic RW RW R R R
|---------- Grouped Elements RW RW R R R
|---------- Control Elements RW RW R R R
|---------- Inputs / Outputs RW RW R R R
|--------------- Contact Inputs RW RW R R R
|--------------- Contact Input RW RW R R R
threshold 2
|--------------- Virtual Inputs RW RW R R R
|--------------- Contact Outputs RW RW R R R
|--------------- Virtual Outputs RW RW R R R
|--------------- Resetting RW RW R R R
|--------------- Direct Inputs RW RW R R R
|--------------- Direct Outputs RW RW R R R
|--------------- Teleprotection RW RW R R R
|--------------- Direct Analogs RW RW R R R
|--------------- Direct Integers RW RW R R R
|---------- Transducer I/O RW RW R R R
|---------- Testing RW RW R R R
|---------- Front Panel Label Designer NA NA NA NA NA
|---------- Protection Summary NA NA NA NA NA
Commands RW RW RW R R
|---------- Virtual Inputs RW RW RW R R
|---------- Clear Records RW RW RW R R
|---------- Set Date and Time RW RW RW R R
User Displays R R R R R
Targets R R R R R
Actual Values R R R R R
|---------- Front Panel R R R R R
|---------- Status R R R R R
|---------- Metering R R R R R
|---------- Transducer I/O R R R R R
|---------- Records R R R R R
|---------- Product Info R R R R R
Maintenance RW RW R R R
|---------- Modbus Analyzer NA NA NA NA NA
|---------- Change front panel RW RW RW R R
|---------- Update firmware Yes No No No No
|---------- Retrieve file Yes No No No No
Table Notes:
RW = read and write access
R = read access
Supervisor = RW (default), Administrator = R (default), Administrator = RW (only if Supervisor role is disabled)
NA = the permission is not enforced by CyberSentry security
CyberSentry user authentication

The following types of authentication are supported by CyberSentry to access the UR device:

ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION
• Device Authentication (local UR device authenticates)

• Server Authentication (RADIUS server authenticates)
The EnerVista software allows access to functionality that is determined by the user role, which comes either from the local
UR device or the RADIUS server.
The EnerVista software has a device authentication option on the login screen for accessing the UR device. When the
"Device" button is selected, the UR uses its local authentication database and not the RADIUS server to authenticate the
user. In this case, it uses its built-in roles (Administrator, Engineer, Supervisor, Observer, Operator, or Administrator and
2 Supervisor when Device Authentication is disabled) as login names and the associated passwords are stored on the UR
device. As such, when using the local accounts, access is not user-attributable.
In cases where user-attributable access is required especially to facilitate auditable processes for compliance reasons, use
RADIUS authentication.
When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication
database to authenticate the user.
No password or security information is displayed in plain text by the EnerVista software or UR device, nor is such
information ever transmitted without cryptographic protection.
CyberSentry server authentication

The UR has been designed to direct automatically the authentication requests based on user names. In this respect, local
account names on the UR are considered as reserved and not used on a RADIUS server.
The UR detects automatically whether an authentication request is to be handled remotely or locally. As there are five local
accounts possible on the UR, if the user ID credential does not match one of the five local accounts, the UR forwards
automatically the request to a RADIUS server when one is provided.
If a RADIUS server is provided, but is unreachable over the network, server authentication requests are denied. In this
situation, use local UR accounts to gain access to the UR system.
2.3 Order codes

A B90 protection system consists of several UR-series B90 IEDs as per user needs and system configuration. At least three
IEDs are required to provide differential and other protection functions for phases A, B, and C of the busbar. The fourth IED
is required for breaker failure functionality and isolator status monitoring as well as extra input and output capability. A
fifth IED is sometimes required for additional input and output capability.
Before ordering the B90 system, an analysis of the required protection and monitoring functions is required. Also, detailed
analyses of required AC inputs and input/output contacts must be performed to select appropriate hardware
configurations for each of the B90 IEDs.
The B90 is provided with an option of protecting 8, 16, or 24-feeder busbars. When ordered as an eight-feeder
protection system, the B90 is configurable for up to eight-input bus differential, regardless of the number of
physical current inputs available in the B90 IEDs.
The relay is available as a 19-inch rack horizontal mount unit and consists of the following modules: power supply, CPU,
CTs and VTs, contact inputs and outputs, and inter-relay communications. Each of these modules can be supplied in a
number of configurations specified at the time of ordering. The information required to completely specify the relay is
provided in the following tables (see chapter 3 for full details of relay modules).
Order codes are subject to change without notice. See the web page for the product for the latest options.
The letters in the top row of the table correspond to slots in the UR chassis, for example slot F, H, or U.
The R-GOOSE protocol described in IEC 61850-8-1 is available through the IEC 61850 software option. R-GOOSE
security requires the CyberSentry software option.
For Japanese, the settings display in Japanese on the graphical front panel, while the keys printed on the panel are
in English.

CHAPTER 2: PRODUCT DESCRIPTION ORDER CODES
Table 2-4: B90 order codes

B90 - * ** - H * * - F ** - H ** - L ** - N ** - S ** - U ** - W/X ** Full Size Horizontal Mount
BASE B90 | | | | | | | | | | | | Base Unit
CPU T | | | | | | | | | | | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC
U | | | | | | | | | | | RS485 with 1 100Base-TX Ethernet, SFP RJ-45 +2 100Base-FX Ethernet,
multimode, SFP with LC
V | | | | | | | | | | | RS485 with 3 100Base-TX Ethernet, SFP with RJ-45
W | | | | | | | | | | | RS485 with 2 100Base-FX Ethernet, multimode ST + 10/100Base-TX Ethernet, RJ-
45
SOFTWARE OPTIONS 00 | | | | | | | | | | Six-zone 8-feeder bus protection
01 | | | | | | | | | | Six-zone 16-feeder bus protection
02 | | | | | | | | | | Six-zone 24-feeder bus protection
03 | | | | | | | | | | Single-zone 24-feeder bus protection
04
05
06
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Six-zone 8-feeder bus protection + IEC 61850
2
07 | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850
10 | | | | | | | | | | Six-zone 8-feeder bus protection + breaker failure
13 | | | | | | | | | | Single-zone 24-feeder bus protection + breaker failure
14 | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + breaker failure
17 | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + breaker failure
A0 | | | | | | | | | | Six-zone 8-feeder bus protection + CyberSentry Lvl 1
A3 | | | | | | | | | | Single-zone 24-feeder bus protection + CyberSentry Lvl 1
A4 | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + CyberSentry Lvl 1
A7 | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + CyberSentry Lvl 1
A8 | | | | | | | | | | Six-zone 8-feeder bus protection + breaker failure + CyberSentry Lvl 1
A9 | | | | | | | | | | Six-zone 16-feeder bus protection + breaker failure + CyberSentry Lvl 1
AA | | | | | | | | | | Six-zone 24-feeder bus protection + breaker failure + CyberSentry Lvl 1
AB | | | | | | | | | | Single-zone 24-feeder bus protection + breaker failure + CyberSentry Lvl 1
AC | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + breaker failure + CyberSentry Lvl
1
AD | | | | | | | | | | Six-zone 16-feeder bus protection + IEC 61850 + breaker failure + CyberSentry Lvl
1
AE | | | | | | | | | | Six-zone 24-feeder bus protection + IEC 61850 + breaker failure + CyberSentry Lvl
1
AF | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + breaker failure + CyberSentry
Lvl 1
B0 | | | | | | | | | | Six-zone 8-feeder bus protection + IEEE 1588
B3 | | | | | | | | | | Single-zone 24-feeder bus protection + IEEE 1588
B4 | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + IEEE 1588
B7 | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + IEEE 1588
B8 | | | | | | | | | | Six-zone 8-feeder bus protection + breaker failure + IEEE 1588
B9 | | | | | | | | | | Six-zone 16-feeder bus protection + breaker failure + IEEE 1588
BA | | | | | | | | | | Six-zone 24-feeder bus protection + breaker failure + IEEE 1588
BB | | | | | | | | | | Single-zone 24-feeder bus protection + breaker failure + IEEE 1588
BC | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588
BD | | | | | | | | | | Six-zone 16-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588
BE | | | | | | | | | | Six-zone 24-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588
BF | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588
C0 | | | | | | | | | | Parallel Redundancy Protocol (PRP) + six-zone 8-feeder bus protection
C1 | | | | | | | | | | PRP + six-zone 16-feeder bus protection
C2 | | | | | | | | | | PRP + six-zone 24-feeder bus protection
C3 | | | | | | | | | | PRP + single-zone 24-feeder bus protection
C4 | | | | | | | | | | PRP + six-zone 8-feeder bus protection + IEC 61850
C7 | | | | | | | | | | PRP + single-zone 24-feeder bus protection + IEC 61850
C8 | | | | | | | | | | PRP + six-zone 8-feeder bus protection + breaker failure
C9 | | | | | | | | | | PRP + six-zone 16-feeder bus protection + breaker failure
CA | | | | | | | | | | PRP + six-zone 24-feeder bus protection + breaker failure
CB | | | | | | | | | | PRP + single-zone 24-feeder bus protection + breaker failure
CC | | | | | | | | | | PRP + six-zone 8-feeder bus protection + breaker failure + IEC 61850
CD | | | | | | | | | | PRP + six-zone 16-feeder bus protection + breaker failure + IEC 61850
CE | | | | | | | | | | PRP + six-zone 24-feeder bus protection + breaker failure + IEC 61850
CF | | | | | | | | | | PRP + single-zone 24-feeder bus protection + breaker failure + IEC 61850
D0 | | | | | | | | | | Six-zone 8-feeder bus protection + IEEE 1588 + CyberSentry Lvl 1
D3 | | | | | | | | | | Single-zone 24-feeder bus protection + IEEE 1588 + CyberSentry Lvl 1
D4 | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + IEEE 1588 + CyberSentry Lvl 1
D7 | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + IEEE 1588 + CyberSentry Lvl
1
D8 | | | | | | | | | | Six-zone 8-feeder bus protection + breaker failure + IEEE 1588 + CyberSentry Lvl
1
D9 | | | | | | | | | | Six-zone 16-feeder bus protection + breaker failure + IEEE 1588 + CyberSentry Lvl
1
DA | | | | | | | | | | Six-zone 24-feeder bus protection + breaker failure + IEEE 1588 + CyberSentry Lvl
1
DB | | | | | | | | | | Single-zone 24-feeder bus protection + breaker failure + IEEE 1588 + CyberSentry
Lvl 1
DC | | | | | | | | | | Six-zone 8-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588 +
CyberSentry Lvl 1
DD | | | | | | | | | | Six-zone 16-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588 +
CyberSentry Lvl 1
DE | | | | | | | | | | Six-zone 24-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588 +
CyberSentry Lvl 1


DF | | | | | | | | | | Single-zone 24-feeder bus protection + IEC 61850 + breaker failure + IEEE 1588 +
CyberSentry Lvl 1
E0 | | | | | | | | | | IEEE 1588 + PRP + six-zone 8-feeder bus protection
E3 | | | | | | | | | | IEEE 1588 + PRP + single-zone 24-feeder bus protection
E4 | | | | | | | | | | IEEE 1588 + PRP + six-zone 8-feeder bus protection + IEC 61850
E7 | | | | | | | | | | IEEE 1588 + PRP + single-zone 24-feeder bus protection + IEC 61850
E8 | | | | | | | | | | IEEE 1588 + PRP + six-zone 8-feeder bus protection + breaker failure
E9 | | | | | | | | | | IEEE 1588 + PRP + six-zone 16-feeder bus protection + breaker failure
EA | | | | | | | | | | IEEE 1588 + PRP + six-zone 24-feeder bus protection + breaker failure
2 EB
EC
ED
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IEEE 1588 + PRP + single-zone 24-feeder bus protection + breaker failure
IEEE 1588 + PRP + six-zone 8-feeder bus protection + breaker failure + IEC 61850
IEEE 1588 + PRP + six-zone 16-feeder bus protection + breaker failure + IEC
61850
EE | | | | | | | | | | IEEE 1588 + PRP + six-zone 24-feeder bus protection + breaker failure + IEC
61850
EF | | | | | | | | | | IEEE 1588 + PRP + single-zone 24-feeder bus protection + breaker failure + IEC
61850
F0 | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection
F3 | | | | | | | | | | PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection
F4 | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + IEC 61850
F7 | | | | | | | | | | PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection + IEC 61850
F8 | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + breaker failure
F9 | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 16-feeder bus protection + breaker failure
FA | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus protection + breaker failure
FB | | | | | | | | | | PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection + breaker failure
FC | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + breaker failure + IEC
61850
FD | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 16-feeder bus protection + breaker failure +
IEC 61850
FE | | | | | | | | | | PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus protection + breaker failure +
IEC 61850
FF | | | | | | | | | | PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection + breaker failure
+ IEC 61850
G0 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection
G3 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection
G4 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + IEC
61850
61850
61850
G7 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection + IEC
61850
G8 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + breaker
failure
G9 | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 16-feeder bus protection +
breaker failure
GA | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus protection +
breaker failure
GB | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection +
breaker failure
GC | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus protection + breaker
failure + IEC 61850
GD | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 16-feeder bus protection +
breaker failure + IEC 61850
GE | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus protection +
GF | | | | | | | | | | IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder bus protection +
J0 | | | | | | | | | | IEC 60870-5-103 + six-zone 8-feeder bus protection
J3 | | | | | | | | | | IEC 60870-5-103 + single-zone 24-feeder bus protection
J4 | | | | | | | | | | IEC 60870-5-103 + six-zone 8-feeder bus protection + IEC 61850
J7 | | | | | | | | | | IEC 60870-5-103 + single-zone 24-feeder bus protection + IEC 61850
J8 | | | | | | | | | | IEC 60870-5-103 + six-zone 8-feeder bus protection + breaker failure
J9 | | | | | | | | | | IEC 60870-5-103 + six-zone 16-feeder bus protection + breaker failure
JA | | | | | | | | | | IEC 60870-5-103 + six-zone 24-feeder bus protection + breaker failure
JB | | | | | | | | | | IEC 60870-5-103 + single-zone 24-feeder bus protection + breaker failure
JC | | | | | | | | | | IEC 60870-5-103 + six-zone 8-feeder bus protection + breaker failure + IEC 61850
JD | | | | | | | | | | IEC 60870-5-103 + six-zone 16-feeder bus protection + breaker failure + IEC
61850
JE | | | | | | | | | | IEC 60870-5-103 + six-zone 24-feeder bus protection + breaker failure + IEC
61850
JF | | | | | | | | | | IEC 60870-5-103 + single-zone 24-feeder bus protection + breaker failure + IEC
61850
K0 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 8-feeder bus protection
K3 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + single-zone 24-feeder bus protection
K4 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 8-feeder bus protection + IEC
61850
61850
61850
K7 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + single-zone 24-feeder bus protection + IEC
61850

CHAPTER 2: PRODUCT DESCRIPTION ORDER CODES

K8 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 8-feeder bus protection + breaker
failure
K9 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 16-feeder bus protection +
breaker failure
KA | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 24-feeder bus protection +
breaker failure
KB | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + single-zone 24-feeder bus protection +
breaker failure
KC | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 8-feeder bus protection + breaker
failure + IEC 61850
KD | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 16-feeder bus protection +
KE | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + six-zone 24-feeder bus protection +
KF | | | | | | | | | |
IEC 60870-5-103 + IEEE 1588 + PRP + single-zone 24-feeder bus protection +
2
L0 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus
protection
protection
protection
L3 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder
bus protection
protection + IEC 61850
L7 | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder
bus protection + IEC 61850
protection + breaker failure
LA | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus
LB | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder
bus protection + breaker failure
LC | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 8-feeder bus
protection + breaker failure + IEC 61850
LD | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 16-feeder bus
LE | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + six-zone 24-feeder bus
LF | | | | | | | | | | IEC 60870-5-103 + IEEE 1588 + PRP + CyberSentry Lvl 1 + single-zone 24-feeder
bus protection + breaker failure + IEC 61850
MOUNT/COATING H | | | | | | | | | Horizontal (19” rack)
A | | | | | | | | | Horizontal (19” rack) with harsh-environmental coating
FRONT PANEL + INTERFACE C | | | | | | | | English display
D | | | | | | | | French display
R | | | | | | | | Russian display
A | | | | | | | | Chinese display
P | | | | | | | | English display with 4 small and 12 large programmable pushbuttons
G | | | | | | | | French display with 4 small and 12 large programmable pushbuttons
S | | | | | | | | Russian display with 4 small and 12 large programmable pushbuttons
B | | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttons
K | | | | | | | | Enhanced front panel with English display
M | | | | | | | | Enhanced front panel with French display
Q | | | | | | | | Enhanced front panel with Russian display
U | | | | | | | | Enhanced front panel with Chinese display
L | | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | | | | Enhanced front panel with Turkish display
Y | | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons
I | | | | | | | | Enhanced front panel with German display
J | | | | | | | | Enhanced front panel with German display and user-programmable
pushbuttons
H | | | | | | | | Enhanced front panel with Polish display
O | | | | | | | | Enhanced front panel with Polish display and user-programmable pushbuttons
E | | | | | | | | 7" Graphical front panel display in multiple languages with USB front port and
user-programmable pushbuttons (English, French, Chinese, Russian, Turkish,
German, Polish, Japanese)
POWER SUPPLY H | | | | | | | 125 / 250 V AC/DC
(redundant power supply H | | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supply
must be same type as main L | | | | | | | 24 to 48 V (DC only)
power supply) L | | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply
ENHANCED DIAGNOSTICS CT/VT XX | XX | XX | | None
DSP 8L | 8L | 8L | | Standard 4CT/4VT with enhanced diagnostics
(requires all DSP to be enhanced 8N | 8N | 8N | | Standard 8CT with enhanced diagnostics
diagnostic) 8S | 8S | 8S | | Standard 7CT/1VT with enhanced diagnostics
CONTACT INPUTS/OUTPUTS XX XX XX XX XX XX | No Module
4A 4A 4A 4A 4A 4A | 4 Solid state (no monitoring) MOSFET outputs
4B 4B 4B 4B 4B 4B | 4 Solid state (voltage with optional current) MOSFET outputs
4C 4C 4C 4C 4C 4C | 4 Solid state (current with optional voltage) MOSFET outputs
4D 4D 4D 4D 4D 4D | 16 Contact inputs with auto-burnish
4L 4L 4L 4L 4L 4L | 14 Form-A (no monitoring) latchable outputs


6A 6A 6A 6A 6A 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs
6B 6B 6B 6B 6B 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs
6C 6C 6C 6C 6C 6C | 8 Form-C outputs
6D 6D 6D 6D 6D 6D | 16 Contact inputs
6E 6E 6E 6E 6E 6E | 4 Form-C outputs, 8 contact inputs
6F 6F 6F 6F 6F 6F | 8 Fast Form-C outputs
6G 6G 6G 6G 6G 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs
6H 6H 6H 6H 6H 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs
6K 6K 6K 6K 6K 6K | 4 Form-C and 4 Fast Form-C outputs
6L 6L 6L 6L 6L 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs
6M 6M 6M 6M 6M 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs
6N 6N 6N 6N 6N 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs
6P 6P 6P 6P 6P 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs
2
6R 6R 6R 6R 6R 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs
6S 6S 6S 6S 6S 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs
6T 6T 6T 6T 6T 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs
6U 6U 6U 6U 6U 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs
67 67 67 67 67 67 | 8 Form-A (no monitoring) outputs
6W 6W 6W 6W 6W 6W | 30 Contact inputs - pin terminals (max 4 modules)
6X 6X 6X 6X 6X 6X | 18 Form-A (no monitoring) outputs - pin terminals (max 4 modules)
INTER-RELAY XX No Module
COMMUNICATIONS 2A C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode
(select a maximum of 1 per unit) 2B C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode
2E Bi-phase, single channel
2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
2I Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1300 nm, single-mode,
Laser
2J Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1550 nm, single-mode,
Laser
72 1550 nm, single-mode, Laser, 1 Channel
73 1550 nm, single-mode, Laser, 2 Channel
74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser
75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode Laser
76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, multimode, LED, 1 Channel
7B 1300 nm, multimode, LED, 1 Channel
7C 1300 nm, single-mode, ELED, 1 Channel
7D 1300 nm, single-mode, Laser, 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multimode
7F Channel 1 - G.703; Channel 2 - 1300 nm, multimode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multimode, LED, 2 Channels
7I 1300 nm, multimode, LED, 2 Channels
7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, Laser, 2 Channels
7L Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser
7R G.703, 1 Channel
7S G.703, 2 Channels
7T RS422, 1 Channel
7W RS422, 2 Channels
2.3.1 Replacement modules

Replacement modules can be ordered separately. When ordering a replacement CPU module or front panel, provide the
serial number of your existing unit.
Not all replacement modules apply to the B90 relay. The modules specified in the order codes for the B90 are available as
replacement modules for the B90.
The order codes shown here are subject to change without notice. See the web page for the product for the latest options.
Table 2-5: UR order codes for replacement modules, horizontal units
UR - ** - *
POWER SUPPLY | SH A| 125 / 300 V AC/DC
redundant supply only available in horizontal | SL H| 24 to 48 V (DC only)
units and must be same type as main supply
CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC
| U | RS485 with 1 100Base-TX Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
| V | RS485 with 3 100Base-TX Ethernet, SFP with RJ-45
| W | RS485 with 2 100Base-FX Ethernet, multimode ST + 10/100Base-TX Ethernet, RJ-45
FRONT PANEL + INTERFACE | 3C | Horizontal front panel with keypad and English display
| 3D | Horizontal front panel with keypad and French display
| 3R | Horizontal front panel with keypad and Russian display
| 3A | Horizontal front panel with keypad and Chinese display
| 3P | Horizontal front panel with keypad, user-programmable pushbuttons, and English display
| 3G | Horizontal front panel with keypad, user-programmable pushbuttons, and French display
| 3S | Horizontal front panel with keypad, user-programmable pushbuttons, and Russian display
| 3B | Horizontal front panel with keypad, user-programmable pushbuttons, and Chinese display
| 3K | Enhanced front panel with English display
| 3M | Enhanced front panel with French display
| 3Q | Enhanced front panel with Russian display
| 3U | Enhanced front panel with Chinese display
| 3L | Enhanced front panel with English display and user-programmable pushbuttons
| 3N | Enhanced front panel with French display and user-programmable pushbuttons
| 3T | Enhanced front panel with Russian display and user-programmable pushbuttons
| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons
| 3W | Enhanced front panel with Turkish display
| 3Y | Enhanced front panel with Turkish display and user-programmable pushbuttons

CHAPTER 2: PRODUCT DESCRIPTION SIGNAL PROCESSING
UR - ** - *
| 3I | Enhanced front panel with German display
| 3J | Enhanced front panel with German display and user-programmable pushbuttons
| 3H | Enhanced front panel with Polish display
| 3O | Enhanced front panel with Polish display and user-programmable pushbuttons
| 3Z | Enhanced front panel with Japanese display
| 3X | Enhanced front panel with Japanese display and user-programmable pushbuttons
| 3E | 7" Graphical front panel display in multiple languages with USB front port and user-programmable pushbuttons
CONTACT INPUTS AND OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs
| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
| 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
| 4D | 16 Contact inputs with Auto-Burnishing
| 4L | 14 Form-A (no monitoring) Latching outputs
| 67 | 8 Form-A (no monitoring) outputs
2
| 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs
| 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs
| 6C | 8 Form-C outputs
| 6D | 16 Contact inputs
| 6E | 4 Form-C outputs, 8 contact inputs
| 6F | 8 Fast Form-C outputs
| 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs
| 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs
| 6K | 4 Form-C and 4 Fast Form-C outputs
| 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs
| 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs
| 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs
| 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs
| 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs
| 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs
| 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs
| 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs
| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 contact inputs
| 6W | 30 Contact inputs - pin terminals (max 4 modules)
| 6X | 18 Form-A (no monitoring) outputs - pin terminals (max 4 modules)
CT/VT MODULES | 8L | Standard 4CT/4VT with enhanced diagnostics
(not available for the C30) | 8N | Standard 8CT with enhanced diagnostics
INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode
| 2B | C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode
| 2E | Bi-phase, single channel
| 2F | Bi-phase, dual channel
| 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
| 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
| 2I | Channel 1 - IEEE C37.94, multimode, 64/128 kbps; Channel 2 - 1300 nm, single-mode, Laser
| 2J | Channel 1 - IEEE C37.94, multimode, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser
| 72 | 1550 nm, single-mode, Laser, 1 Channel
| 73 | 1550 nm, single-mode, Laser, 2 Channel
| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser
| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser
| 76 | IEEE C37.94, 820 nm, multimode, LED, 1 Channel
| 77 | IEEE C37.94, 820 nm, multimode, LED, 2 Channels
| 7A | 820 nm, multimode, LED, 1 Channel
| 7B | 1300 nm, multimode, LED, 1 Channel
| 7C | 1300 nm, single-mode, ELED, 1 Channel
| 7D | 1300 nm, single-mode, Laser, 1 Channel
| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multimode
| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multimode
| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
| 7H | 820 nm, multimode, LED, 2 Channels
| 7I | 1300 nm, multimode, LED, 2 Channels
| 7J | 1300 nm, single-mode, ELED, 2 Channels
| 7K | 1300 nm, single-mode, Laser, 2 Channels
| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED
| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED
| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
| 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser
| 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser
| 7R | G.703, 1 Channel
| 7S | G.703, 2 Channels
| 7T | RS422, 1 Channel
| 7W | RS422, 2 Channels
2.4 Signal processing

2.4.1 UR signal processing
The URs are microprocessor-based protective relays that are designed to measure power system conditions directly via CT
and VT inputs and via other sources of information, such as analog inputs, communications inputs, and contact inputs. The
following figure shows the overall signal processing in URs.
An analog low pass anti-aliasing filter with a 3 dB corner frequency is set at 2.4 kHz and is used for current and voltage
analog filtering as well as signal conditioning. The same filtering is applied for phase, ground currents, phase-to-phase
(when applicable), and auxiliary voltages. The 2.4 kHz cut-off frequency applies to both 50 and 60 Hz applications and fixed
in the hardware, and thus is not dependent on the system nominal frequency setting.

SIGNAL PROCESSING CHAPTER 2: PRODUCT DESCRIPTION
Figure 2-4: UR signal processing
Analog low- Analog-to- Digital band- Phasor

Analog Inputs Digital estimation
pass filter pass filter
Converter
½ cycle Fundamen
U A Fourier tal freq.
Phasors,
From 1 cycle Seq. com-
2
CT/VT Fourier ponents
I Frequency
D
T
RMS
values
Synchro-
Sampling phasors Analog Outputs
DSP module frequency filtering
module
Tracking
HMI frequency Events
Protection
Ethernet selection,
algorithms Control
ports estimation Comtrade, data
I> elements,
Communi-
monitoring logger
Serial cation Z<
Serial
ports protocols U< elements,
FlexLogic, DNP, Modbus,
IEC60870
IRIG-B
Accurate
IEEE Real-Time Time stamping PMU (IEEE C37.118,
Ethernet
1588 clock Synchrophasors Aggregation, IEC 61850-90-5)
SNTP calculations post-filtering IEC 61850 (GOOSE,
CPU module MMS Server)
Contact Inputs
Analog Inputs
Inter-relay
Inter-relay
comms
module
module
module
comms
module
Ddebounce Channel A
filtering monitoring
CRC check D Contact Outputs
module
G.703, RS-422,
Optoisolated C37.94, direct fiber DCmA, RTD
859740A1.vsd
The UR samples its AC signals at 64 samples per cycle, that is, at 3840 Hz in 60 Hz systems, and 3200 Hz in 50 Hz systems.
The sampling rate is adjusted dynamically to the actual system frequency by an accurate and fast frequency tracking
system.
The analog/digital converter has the following ranges of AC signals:
Voltages:
Eq. 2-1
Currents:
Eq. 2-2
Current harmonics are estimated based on raw samples with the use of the full-cycle Fourier filter. Harmonics 2nd through
25th are estimated.

CHAPTER 2: PRODUCT DESCRIPTION SPECIFICATIONS
True RMS value for the current is calculated on a per-phase basis. The true RMS can be used for demand recording or as an
input signal to Time Overcurrent function, if the latter is intended for thermal protection. The true RMS is calculated as per
the widely accepted definition:
Eq. 2-3
RMS values include harmonics, inter-harmonics, DC components, and so on, along with fundamental frequency values.
The true RMS value reflects thermal effects of the current and is used for the thermal related monitoring and protection
2
functions.
Protection and control functions respond to phasors of the fundamental and/or harmonic frequency components
(magnitudes and angles), with an exception for some functions that have an option for RMS or fundamental
measurements, or some function responding to RMS only. This type of response is explained typically in each element's
section in this instruction manual.
Currents are pre-filtered using a Finite Impulse Response (FIR) digital filter. The filter is designed to reject DC components
and low-frequency distortions, without amplifying high-frequency noise. This filter is referred to as a modified MIMIC filter,
which provides excellent filtering and overall balance between speed and accuracy of filtering. The filter is cascaded with
the full-cycle Fourier filter for the current phasor estimation.
Voltages are pre-filtered using a patented FIR digital filter. The filter has been optimized to reject voltage-transformer-
specific distortions, such as Capacitive Voltage Transformer (CVT) noise and high-frequency oscillatory components. The
filter is cascaded with the half-cycle Fourier filter for the voltage phasor estimation.
The URs measure power system frequency using the Clarke transformation by estimating the period of the waveform from
two consecutive zero-crossings in the same direction (negative-to-positive). Voltage or current samples are pre-filtered
using a Finite Impulse Response (FIR) digital filter to remove high frequency noise contained in the signal. The period is
used after several security conditions are met, such as true RMS signal must be above 6% nominal for a certain time. If
these security conditions are not met, the last valid measurement is used for a specific time after which the UR reverts to
nominal system frequency.
Synchrophasors are calculated using a patented convolution integral algorithm. This algorithm allows use of the same
time-stamped samples, which are used for protection and taken at the same sampling frequency. This allows URs to use
one sampling clock for both protection algorithms and synchrophasors.
Synchrophasors on firmware versions 7.23 and up have been tested and certified to meet IEEE C37.118-2011 and
C37.118.1a-2014 standards for both metering and protection classes with outputs available up to 60 synchrophasors per
second for the metering class and 120 synchrophasors per second for the protection class. Synchrophasors measurement
is also available via IEC 61850-90-5 protocol.
The contact inputs threshold is settable in the firmware with 17, 33, 84, and 166 V DC settings available. Inputs are scanned
every 0.5 ms and can be conditioned for the critical applications, using debounce time timer, settable from 0.0 to 16.0 ms.
Contact inputs with auto-burnishing are available as well, when external contacts are exposed to the contamination in a
harsh industrial environment.
All measured values are available in the UR metering section on the front panel and via communications protocols.
Measured analog values and binary signals can be captured in COMTRADE format with sampling rates from 8 to 64
samples per power cycle. Analog values can be captured with the Data Logger, allowing much slower rates extended over
a long period of time.
Other advanced UR order code options are available to support IEC 61850 (including fast GOOSE, ICD/CID/IID files, and so
on), IEEE 1588 (IEEE C37.238 power profile) based time synchronization, CyberSentry (advanced cyber security), the Parallel
Redundancy Protocol (PRP), IEC 60870-5-103, and so on.
2.5 Specifications
Specifications are subject to change without notice.

SPECIFICATIONS CHAPTER 2: PRODUCT DESCRIPTION
2.5.1 Protection elements

The operating times include the activation time of a trip rated form-A output contact unless otherwise indicated. FlexLogic
operands of a given element are 4 ms faster. Take this into account when using FlexLogic to interconnect with other
protection or control elements of the relay, building FlexLogic equations, or interfacing with other intelligent electronic
devices (IEDs) or power system devices via communications or different output contacts. If not specified, the operate times
given here are for a 60 Hz system at nominal system frequency. Operate times for a 50 Hz system are 1.2 times longer.
2 BUS DIFFERENTIAL (87B)

Pickup level: 0.050 to 6.000 pu in steps of 0.001
Low slope: 15 to 100% in steps of 1
High slope: 50 to 100% in steps of 1
Low breakpoint: 1.00 to 30.00 pu in steps of 0.01
High breakpoint: 1.00 to 30.00 pu in steps of 0.01
High set level: 0.10 to 99.99 pu in steps of 0.01
Dropout level: 97 to 98% of pickup
Characteristic accuracy: ±3% of the maximum circuit current or ±2% of rated (whichever is greater)
Operating time: one power system cycle (typical)
Number of zones: 1 or 6 (option)
Max number of inputs: 8, 16, or 24 (option)
CT TROUBLE
Responding to: Differential current
Pickup delay: 1.0 to 60.0 sec. in steps of 0.1
Timer accuracy: ±3% of operate time or ±1/4 cycle (whichever is greater)
Availability: one per zone of protection
ISOLATOR MONITORING
Responding to: Both normally-open and normally-closed auxiliary contacts
Asserting: Isolator Position, Isolator Alarm, Block Switching
Alarm pickup delay: 0.00 to 120.00 s in steps of 0.05
TIME OVERCURRENT
Level accuracy:
0.1 to 2.0  CT 0.5% of reading or 1% of nominal (whichever is greater)
above 2.0  CT 1.5% of reading
Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse,
Short/Very/Extremely Inverse; I2t; FlexCurves™ (programmable); Definite Time (0.01 s base
curve)
TD multiplier: 0.00 to 600.00 in steps of 0.01
Reset type: Instantaneous or Timed (per IEEE)
Curve timing accuracy at 1.03 to 20 x pickup:
±3.5% of operate time or ±1/2 cycle (whichever is greater) from pickup to operate
INSTANTANEOUS OVERCURRENT
Level accuracy:
0.1 to 2.0  CT 0.5% of reading or 1% of nominal (whichever is greater)
above 2.0  CT 1.5% of reading
Pickup delay: 0 to 65.535 s in steps of 0.001
Reset delay: 0 to 65.535 s in steps of 0.001


Operate time: <16 ms at 3x pickup at 60 Hz
UNDERVOLTAGE
Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0 to 65.535 s in steps of 0.001
Reset delay:
Timer accuracy:
0 to 65.535 s in steps of 0.001
±3% of operate time or ±1/4 cycle (whichever is greater) 2
Operate time: <16 ms at <0.9 x pickup at 60 Hz
END FAULT PROTECTION

IOC pickup level: 0.020 to 30.000 pu in steps of 0.001
IOC dropout level: 97 to 98% of pickup
Level accuracy
at 0.1 to 2.0  CT: 0.5% of reading or 1% of nominal (whichever is greater)
above 2.0  CT: 1.5% of reading
CB open pickup timer: 0 to 65.535 s in steps of 0.001
End Fault pickup timer: 0 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±8 ms, whichever is greater
BREAKER FAILURE
Mode: 3-pole
Current supervision: phase current
Current supv. pickup: 0.020 to 30.000 pu in steps of 0.001
Current supv. dropout: 97 to 98% of pickup
Current supv. accuracy:
0.1 to 2.0  CT rating: ±0.75% of reading or ±2% of rated (whichever is greater)
above 2  CT rating: ±2.5% of reading
TRIP BUS (TRIP WITHOUT FLEXLOGIC)

Number of elements: 6
Number of inputs: 16
Operate time: <2 ms at 60 Hz
Timer accuracy: ±3% or 10 ms, whichever is greater
2.5.2 User-programmable elements

FLEXLOGIC
Programming language: Reverse Polish Notation with graphical visualization (keypad programmable)
Lines of code: 1024
Internal variables: 64
Supported operations: NOT, XOR, OR (2 to 16 inputs), AND (2 to 16 inputs), NOR (2 to 16 inputs), NAND (2 to 16 inputs),
latch (reset-dominant), edge detectors, timers
Inputs: any logical variable, contact, or virtual input
Number of timers: 32
Pickup delay: 0 to 60000 (ms, sec., min.) in steps of 1
Dropout delay: 0 to 60000 (ms, sec., min.) in steps of 1
FLEXCURVES™
Number: 4 (A through D)
Reset points: 40 (0 through 1 of pickup)
Operate points: 80 (1 through 20 of pickup)
Time delay: 0 to 65535 ms in steps of 1

FLEX STATES
Number: up to 256 logical variables grouped under 16 Modbus addresses
Programmability: any logical variable, contact, or virtual input
NON-VOLATILE LATCHES
Type: set-dominant or reset-dominant
Number: 16 (individually programmed)
Output: stored in non-volatile memory
2 Execution sequence: as input prior to protection, control, and FlexLogic
USER-PROGRAMMABLE LEDs (Enhanced and basic front panels)

Number: 48 plus trip and alarm
Programmability: from any logical variable, contact, or virtual input
Reset mode: self-reset or latched
LED TEST
Initiation: from any contact input or user-programmable condition
Number of tests: 3, interruptible at any time
Duration of full test: approximately 3 minutes
Test sequence 1: all LEDs on
Test sequence 2: all LEDs off, one LED at a time on for 1 s
Test sequence 3: all LEDs on, one LED at a time off for 1 s
USER-DEFINABLE DISPLAYS (Enhanced and basic front panels)

Number of displays: 16
Lines of display: 2  20 alphanumeric characters
Parameters: up to 5, any Modbus register addresses
Invoking and scrolling: keypad, or any user-programmable condition, including pushbuttons
CONTROL PUSHBUTTONS (Enhanced and basic front panels)

Number of pushbuttons: 7
Operation: drive FlexLogic operands
USER-PROGRAMMABLE PUSHBUTTONS (Optional)

Number of pushbuttons: 12 on basic front panel
16 on enhanced horizontal front panel
6 on enhanced vertical front panel
16 on graphical front panel (8 physical pushbuttons, 8 graphical interface pushbuttons)
Mode: self-reset, latched
Display message: 2 lines of 20 characters each
Drop-out timer: 0.00 to 60.00 s in steps of 0.05
Autoreset timer: 0.2 to 600.0 s in steps of 0.1
Hold timer: 0.0 to 10.0 s in steps of 0.1
DIGITAL ELEMENTS
Operating signal: any FlexLogic operand
Pickup delay: 0.000 to 999999.999 s in steps of 0.001
Dropout delay: 0.000 to 999999.999 s in steps of 0.001
Timing accuracy: ±3% or ±4 ms, whichever is greater
2.5.3 Monitoring
OSCILLOGRAPHY
Maximum records: 64
Sampling rate: 64 samples per power cycle
Triggers: any element pickup, dropout, or operate; contact input change of state; contact output change
of state; FlexLogic equation

Data: AC input channels; element state; contact input state; contact output state
Data storage: in non-volatile memory
EVENT RECORDER
Capacity: 1024 events
Time-tag: to 1 microsecond
Triggers: any element pickup, dropout, or operate; contact input change of state; contact output change
of state; self-test events
Data storage: in non-volatile memory
2
USER-PROGRAMMABLE FAULT REPORT
Pre-fault trigger: any FlexLogic operand
Fault trigger: any FlexLogic operand
Recorder quantities: 32 (any FlexAnalogTM value)
2.5.4 Metering
CURRENT METERING
Accuracy at
0.1 to 2.0  CT rating: ±0.25% of reading or ±0.1% of rated (whichever is greater)
2.0  CT rating: ±1.0% of reading
VOLTAGE
Accuracy: ±0.5% of reading from 10 to 208 V
FREQUENCY
Accuracy at
V = 0.8 to 1.2 pu: ±0.001 Hz (when voltage signal is used for frequency measurement)
I = 0.1 to 0.25 pu: ±0.005 Hz
I > 0.25 pu: ±0.02 Hz (when current signal is used for frequency measurement)
2.5.5 Inputs
AC CURRENT
CT rated primary: 1 to 50000 A
CT rated secondary: 1 or 5 A by connection
Relay burden: < 0.2 VA at rated secondary
Conversion range: 0.02 to 46  CT rating RMS symmetrical
Current withstand: 20 ms at 250 times rated
1 sec at 100 times rated
continuous 4xInom
URs equipped with 24 CT inputs have a maximum operating temperature of 50°C
Short circuit rating: 150000 RMS symmetrical amperes, 250 V maximum (primary current to external CT)
AC VOLTAGE
VT rated secondary: 50.0 to 240.0 V
VT ratio: 1.00 to 24000.00
Relay burden: < 0.25 VA at 120 V
Conversion range: 1 to 275 V
Voltage withstand: continuous at 260 V to neutral
1 min/hr at 420 V to neutral
FREQUENCY
Nominal frequency setting: 25 to 60 Hz

Sampling frequency: 64 samples per power cycle

Tracking frequency range: 20 to 70 Hz
CONTACT INPUTS
Dry contacts: 1000  maximum
Wet contacts: 300 V DC maximum
Selectable thresholds: 17 V, 33 V, 84 V, 166 V
Tolerance: ±10%
2 Contacts per common return:

Recognition time:
4
< 1 ms
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Continuous current draw: 4 mA (when energized)
CONTACT INPUTS WITH AUTO-BURNISHING

Dry contacts: 1000  maximum
Wet contacts: 300 V DC maximum
Selectable thresholds: 17 V, 33 V, 84 V, 166 V
Tolerance: ±10%
Contacts per common return: 2
Recognition time: < 1 ms
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Continuous current draw: 4 mA (when energized)
Auto-burnish impulse current: 50 to 70 mA
Duration of auto-burnish impulse: 25 to 50 ms
IRIG-B INPUT
IRIG formats accepted: B000…B007, B120…B127
IRIG control bits: IEEE Std C37.118.1-2011
Amplitude modulation: 1 to 10 V pk-pk
DC shift: TTL–Compatible
Input impedance: 50 k
Isolation: 2 kV
DIRECT INPUTS
Input points: 256
Remote devices: 16
Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Ring configuration: Yes, No
Data rate: 64, 128, or 213 kbps
CRC: 32-bit
CRC alarm:
Responding to: Rate of messages failing the CRC
Monitoring message count: 10 to 10000 in steps of 1
Alarm threshold: 1 to 1000 in steps of 1
Unreturned message alarm:
Responding to: Rate of unreturned messages in the ring configuration
Monitoring message count: 10 to 10000 in steps of 1
Alarm threshold: 1 to 1000 in steps of 1
2.5.6 Power supply

LOW RANGE
Nominal DC voltage: 24 to 48 V
Minimum DC voltage: 20 V
Maximum DC voltage: 75 V for SL power supply module
Voltage loss hold-up: 200 ms duration at maximum load

NOTE: Low range is DC only.
HIGH RANGE
Nominal DC voltage: 125 to 250 V
Minimum DC voltage: 88 V
Maximum DC voltage: 300 V
Nominal AC voltage: 100 to 240 V at 50/60 Hz
Minimum AC voltage: 88 V at 25 to 100 Hz
Maximum AC voltage:
Voltage loss hold-up:
265 V at 25 to 100 Hz
200 ms duration at maximum load 2
ALL RANGES
Volt withstand: 2  Highest Nominal Voltage for 10 ms
Power consumption: typical = 15 to 20 W/VA
maximum = 45 W/VA
contact factory for exact order code consumption
INTERNAL FUSE
Ratings:
Low range power supply: 8 A / 250 V
High range power supply: 4 A / 250 V
Interrupting capacity:
AC: 100 000 A RMS symmetrical
DC: 10 000 A
2.5.7 Outputs
FORM-A RELAY
Make and carry for 0.2 s: 30 A as per ANSI C37.90
Carry continuous: 6A
Break (DC inductive, L/R = 40 ms):
Voltage Current
24 V 1A
48 V 0.5 A
125 V 0.3 A
250 V 0.2 A
Operate time: < 4 ms

Contact material: silver alloy
LATCHING RELAY
Carry continuous: 6 A as per IEEE C37.90
Break (DC resistive as per IEC61810-1):
Voltage Current
24 V 6A
48 V 1.6 A
125 V 0.4 A
250 V 0.2 A

Control: separate operate and reset inputs
Control mode: operate-dominant or reset-dominant

FORM-A VOLTAGE MONITOR

Applicable voltage: approx. 15 to 250 V DC
Trickle current: approx. 1 to 2.5 mA
FORM-A CURRENT MONITOR

Threshold current: approx. 80 to 100 mA
FORM-C AND CRITICAL FAILURE RELAY

2 Carry continuous: 8A
Break (DC inductive, L/R = 40 ms):
Voltage Current
24 V 1A
48 V 0.5 A
125 V 0.3 A
250 V 0.2 A

FAST FORM-C RELAY

Make and carry: 0.1 A max. (resistive load)
Minimum load impedance:
Input voltage Impedance

2 W Resistor 1 W Resistor
250 V DC 20 K 50 K
120 V DC 5 K 2 K
48 V DC 2 K 2 K
24 V DC 2 K 2 K
Note: values for 24 V and 48 V are the same due to a
required 95% voltage drop across the load
impedance.
Operate time: < 0.6 ms

Internal Limiting Resistor: 100  2 W
SOLID-STATE OUTPUT RELAY

Operate and release time: <100 µs
Maximum voltage: 265 V DC
Maximum leakage current in off state
(excluding voltage monitor circuit current): 100 µA
Maximum continuous current: 5 A at 45°C; 4 A at 65°C
Make and carry:
for 0.2 s: 30 A as per ANSI C37.90
for 0.03 s: 300 A

Breaking capacity:
Specification UL 508 Utility application Industrial application

(autoreclose scheme)
Operations per 5000 operations, 5 operations 10000 operations
interval 1 second on, 0.2 seconds on 0.2 seconds on
9 seconds off 0.2 seconds off 30 seconds off
within 1 minute
1000 operations
0.5 seconds on,
Break capability
0.5 seconds off
3.2 A at L/R = 10 ms 10 A at L/R = 40 ms 10 A at L/R = 40 ms
2
(0 to 250 V DC)
1.6 A at L/R = 20 ms
0.8 A
L/R = 40 ms
CONTROL POWER EXTERNAL OUTPUT (For dry contact input)

Capacity: 100 mA DC at 48 V DC
Isolation: ±300 Vpk
DIRECT OUTPUTS
Output points: 256
2.5.8 Communications
IEC 61850
IEC 61850: Supports IEC 61850 Editions 1.0 and 2.0. See the UR Family Communications Guide and its con-
formance statements.
RS232 (Enhanced and basic front panels)

Front port: 19.2 kbps, Modbus RTU
USB (Graphical front panel)

Front port: USB 2.0 type B
RS485
1 rear port: up to 115 kbps, Modbus RTU, DNP 3, IEC 60870-5-103
Typical distance: 1200 m
Isolation: 2 kV, isolated together at 36 Vpk
FIBER ETHERNET PORT

Parameter Fiber type
100 Mb multimode
Wavelength 1310 nm
Connector LC
Transmit power –20 dBm
Receiver sensitivity –30 dBm
Power budget 10 dB
Maximum input power –14 dBm
Typical distance 2 km
Full duplex yes
Redundancy yes
ETHERNET (10/100 MB TWISTED PAIR)

Modes: 10 Mb, 10/100 Mb (auto-detect)
Connector: RJ45

SIMPLE NETWORK TIME PROTOCOL (SNTP)

Clock synchronization error: <10 ms (typical)
PRECISION TIME PROTOCOL (PTP)

PTP IEEE Std 1588 2008 (version 2)
Power Profile (PP) per IEEE Standard PC37.238TM2011
Slave-only ordinary clock
Peer delay measurement mechanism
2 PARALLEL REDUNDANCY PROTOCOL (PRP)

(IEC 62439-3 CLAUSE 4, 2012)
Ethernet ports used: 2 and 3
Networks supported: 10/100 Mb Ethernet
OTHER
TFTP, SFTP, HTTP, IEC 60870-5-104, Ethernet Global Data (EGD), IEEE C37.118
2.5.9 Inter-relay communications

SHIELDED TWISTED-PAIR INTERFACE OPTIONS
Interface type Typical distance
RS422 1200 m
G.703 100 m
RS422 distance is based on transmitter power and does not take into consideration the clock source provided by
the user.
LINK POWER BUDGET AND MAXIMUM OPTICAL INPUT POWER

The following specifications apply to filter interface modules manufactured from January 2012.
Emitter, fiber type Cable type Transmit power Received Power budget Maximum
sensitivity optical input
power
820 nm, Multimode 62.5/125 μm -16 dBm -32 dBm 16 dBm -8 dBm
50/125 μm -20 dBm 12 dBm
1300 nm, Multimode 62.5/125 μm -16 dBm -32 dBm 16 dBm -8 dBm
50/125 μm -20 dBm 12 dBm
1300 nm, Single 9/125 μm -15 dBm -32 dBm 17 dBm -8 dBm
mode
1300 nm Laser, 9/125 μm 0 dBm -34 dBm 34 dBm -8 dBm
Single mode
1550 nm Laser, 9/125 μm 5 dBm -34 dBm 39 dBm -10 dBm
Single mode
The following specifications apply to filter interface modules implemented before January 2012.
Emitter, fiber type Transmit Received Power budget Maximum optical

power sensitivity input power
820 nm LED, Multimode –20 dBm –30 dBm 10 dB –7.6 dBm
1300 nm LED, Multimode –21 dBm –30 dBm 9 dB –11 dBm
1300 nm ELED, Single mode –23 dBm –32 dBm 9 dB –14 dBm
1300 nm Laser, Single mode –1 dBm –30 dBm 29 dB –14 dBm
1550 nm Laser, Single mode +5 dBm –30 dBm 35 dB –14 dBm

The power budgets are calculated from the manufacturer’s worst-case transmitter power and worst case receiver
sensitivity.
The power budgets for the 1300 nm ELED are calculated from the manufacturer's transmitter power and receiver
sensitivity at ambient temperature. At extreme temperatures these values deviate based on component tolerance.
On average, the output power decreases as the temperature is increased by a factor of 1 dB / 5 °C.
TYPICAL LINK DISTANCE

Emitter, fiber type Cable type Connector Typical distance 2
type
Before From
January January
2012 2012
820 nm LED, 62.5/125 μm ST 1.65 km 2 km
multimode
50/125 μm ST 1.65 km 2 km
1300 nm LED, 62.5/125 μm ST 4 km 5 km
multimode
50/125 μm ST 4 km 5 km
1300 nm ELED, 9/125 μm ST 11.4 km 20 km
single mode
1300 nm Laser, 9/125 μm ST 64 km 65 km
single mode
1550 nm Laser, 9/125 μm ST 105 km 125 km
single mode
Typical distances listed are based on the following assumptions for system loss. As actual losses vary from one
installation to another, the distance covered by your system can vary.
CONNECTOR LOSSES (Total of both ends)

ST connector: 0.7 dB (each)
FIBER LOSSES
820 nm multimode: 3 dB/km
1300 nm multimode: 1 dB/km
1300 nm single mode: 0.35 dB/km
1550 nm single mode: 0.25 dB/km
Splice losses: one splice every 2 km at 0.05 dB loss per splice
SYSTEM MARGIN
3 dB additional loss added to calculations to compensate for all other losses.
Compensated difference in transmitting and receiving (channel asymmetry) channel delays using GPS satellite clock: 10 ms
2.5.10 CyberSentry security

OPTIONS
Software options: Level 1
2.5.11 Graphical front panel

DISPLAY
Type: color graphical back-lit LCD display
Size: 7 inches (17.8 cm)
Resolution: 800 by 480 pixels

Pages: 5 single-line diagram pages with controls, status, and metering values
up to 8 annunciator pages with total of 96 annunciator windows
1 phasor metering page for each AC Source
5 tabular metering pages with dynamic metering and status
event records page with dynamic update
product information page
settings, actual values, error messages (targets)
LED INDICATORS
2 Functions: 5 device status indicators
9 event cause indicators
8 user-programmable pushbutton indicators
PUSHBUTTONS
Type: membrane
Functions: 5 bottom Tab pushbuttons and 1 Home pushbutton for page recall
4 directional, 1 ENTER, and 1 ESCAPE pushbutton element selection
10 side pushbuttons for power system element control
RESET pushbutton
8 physical user-programmable pushbuttons, 8 graphical interface pushbuttons
INGRESS PROTECTION
IP code: IP54 front, IP10 back (IP20 back with IP20 cover accessory)
2.5.12 Environmental
AMBIENT TEMPERATURES
Storage temperature: –40 to 85°C
Operating temperature: –40 to 60°C; the LCD contrast can be impaired at temperatures less than –20°C
HUMIDITY
Humidity: operating up to 95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6 days)
OTHER
Altitude: 2000 m (maximum)
Pollution degree: II
Overvoltage category: II
Ingress protection: IP20 front, IP10 back (basic front panel and Rev. 1 enhanced front panel)
IP40 front, IP10 back (Rev. 2 enhanced front panel)
IP54 front with IP54 mounting collar accessory (Rev. 2 enhanced front panel)
Ingress protection with IP20 cover accessory:
IP20 back
Noise: 0 dB

2.5.13 Type tests

B90 TYPE TESTS
Test Reference standard Test level
1
Dielectric voltage withstand EN 60255-5 2.2 kV
Impulse voltage withstand EN 60255-51 5 kV
Damped oscillatory IEC 61000-4-18 / IEC 60255-22-1 2.5 kV CM, 1 kV DM
Electrostatic discharge EN 61000-4-2 / IEC 60255-22-2 Level 3 2
RF immunity EN 61000-4-3 / IEC 60255-22-3 Level 3
Fast transient disturbance EN 61000-4-4 / IEC 60255-22-4 Class A and B
Surge immunity EN 61000-4-5 / IEC 60255-22-5 Level 3 and 4
Conducted RF immunity EN 61000-4-6 / IEC 60255-22-6 Level 3
1
Power frequency immunity EN 61000-4-7 / IEC 60255-22-7 Class A and B
Voltage interruption and ripple DC IEC 60255-11 12% ripple, 200 ms interrupts
Radiated and conducted emissions CISPR11 / CISPR22 / IEC 60255-25 Class A
Sinusoidal vibration IEC 60255-21-1 Class 1
Shock and bump IEC 60255-21-2 Class 1
Seismic IEC 60255-21-3 Class 1
Power magnetic immunity IEC 61000-4-8 Level 5
Pulse magnetic immunity IEC 61000-4-9 Level 4
Damped magnetic immunity IEC 61000-4-10 Level 4
Voltage dip and interruption IEC 61000-4-11 0, 40, 70, 80% dips; 250 / 300 cycle interrupts
Damped oscillatory IEC 61000-4-121 2.5 kV CM, 1 kV DM
Conducted RF immunity, 0 to 150 kHz IEC 61000-4-16 Level 4
Voltage ripple IEC 61000-4-17 15% ripple
1
Ingress protection IEC 60529 IP20 front, IP10 back
Cold IEC 60068-2-1 –40°C for 16 hours
Hot IEC 60068-2-2 85°C for 16 hours
Humidity IEC 60068-2-30 6 days, variant 1
Damped oscillatory IEEE/ANSI C37.90.1 2.5 kV, 1 MHz
RF immunity IEEE/ANSI C37.90.2 20 V/m, 80 MHz to 1 GHz
Safety UL 508 e83849 NKCR
Section 43 - Temperature test
Energization of Contact Inputs and/or Contact
Outputs for continuous duty is not to exceed a
total of 31 W of power
Safety UL C22.2-14 e83849 NKCR7
Safety UL 1053 e83849 NKCR
Safety IEC 60255-27 Insulation: class 1, Pollution degree: 2, Over
voltage cat II
1 Not tested by third party.
2.5.14 Production tests

THERMAL
Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process.

2.5.15 Approvals
APPROVALS
Compliance Applicable council directive According to
CE Low voltage directive EN 60255-5
EMC directive EN 60255-26 / EN 50263
EN 61000-6-5
2 C-UL-US --- UL 508

UL 1053
C22.2 No. 14
2.5.16 Maintenance
MOUNTING
Attach mounting brackets using 20 inch-pounds (±2 inch-pounds) of torque.
CLEANING
Normally, cleaning is not required. When dust has accumulated on the front panel display, wipe with a dry cloth.
To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized
state once per year, for one hour continuously.

Chapter 3: Installation
Installation
This chapter outlines installation of hardware and software. You unpack, mount, wire the unit, turn on power, then install
the software and configure settings.
3.1 Unpack and inspect

To unpack and inspect the unit:
1. Open the relay package and check that the following items have been delivered:
– B90
– Mounting screws
– GE EnerVista™ DVD (software and documentation)
– B90 Instruction Manual (soft copy on DVD; printed copy if ordered)
– UR Family Communications Guide (soft copy on DVD; printed copy if Instruction Manual ordered)
– Certificate of Calibration
– Test Report
– EC Declaration of Conformity
– Front panel label package
2. Inspect the unit for physical damage.
3. View the rear nameplate and verify that the correct model has been delivered. The model number is at the top right.
Model: B90D00HCHF8AH6AM6BP8BX7A
B90
RATINGS:
Mods: NONE
Control Power: 88-300V DC @ 35W / 77-265V AC @ 35VA See manual
Bus Differential Relay Contact Inputs: 300 VDC Max 10mA
Wiring Diagram:
Inst. Manual: 1601-0115
Contact Outputs: Refer to Instruction Manual Serial Number: MAZB98000029
E83849 Firmware: D
GE Multilin Mfg. Date: NOV 26, 2012
- M A A B 9 7 0 0 0 0 9 9 -
PO Num: 600001234.56
Item Num:
LISTED
®
®
IND.CONT. EQ.
52TL - M A A B 9 7 0 0 0 0 9 9 -
836782A3.CDR
4. Any protective plastic film on the front panel is normally peeled off, but also can be left on.
5. For any issues, contact GE as outlined in the For Further Assistance section in chapter 1.
6. Check that you have the latest copy of the B90 Instruction Manual and the UR Family Communications Guide, for the
applicable firmware version, at http://www.gegridsolutions.com/multilin/manuals/index.htm

PANEL CUTOUTS CHAPTER 3: INSTALLATION
The Instruction Manual outlines how to install, configure, and use the unit. The Communications Guide is for advanced use
with communication protocols. The warranty is included at the end of this instruction manual and on the GE Grid Solutions
website.
3.2 Panel cutouts

Install the relay in an indoor environment within the environmental specifications. The relay complies with Pollution
Category II, which means installation in an office, laboratory, or testing environment.
The B90 is available as a 19-inch rack horizontal mount unit with a removable front panel. The front panel is specified as
enhanced, basic, or graphical at the time of ordering. The enhanced and graphical front panels have additional user-
programmable pushbuttons and LED indicators, while the basic front panel has additional user-programmable
pushbuttons.
3 The modular design allows the relay to be upgraded and repaired by qualified service personnel. The front panel is hinged
to allow access to the modules. The front panel is itself removable to allow mounting on doors with limited rear depth and
for upgrading.
In November 2017, GE began transitioning to Rev. 2 of the enhanced horizontal front panel. This panel can be identified by
the use of a screw instead of a knob to close the panel. It can conform to an IP54 rating with the IP54 mounting collar
purchased separately. The IP54 mounting collar can be used in panel-mount installations, not 19-inch rack-mount
installations. The IP54 mounting collar cannot be used with Rev. 1 enhanced front panels.
The case dimensions are shown in the following figures, along with panel cutout details for panel mounting. When
planning the location of your panel cutout, ensure that provision is made for the front panel to swing open without
interference to or from adjacent equipment.
Mount the relay such that the front panel sits semi-flush with the panel or switchgear door, allowing the operator access to
the keypad and the front communications port.

CHAPTER 3: INSTALLATION PANEL CUTOUTS
Figure 3-1: Horizontal dimensions (Rev. 1 enhanced front panel)
11.016”
[279,81 mm]
9.687”
[246,05 mm]
17.56”
[446,02 mm]
3
7.460”
[189,48 mm]
6.995” 6.960”
[177,67 mm] [176,78 mm]
19.040”
[483,62 mm] 842807A1.CDR

Figure 3-2: Horizontal dimensions (Rev. 2 enhanced front panel)
9.687”
[24.605 cm] 10.97”
[27.86 cm]
3 17.59” [44.68 cm]
6.995” 6.96”
[17.767 cm] [17.68 cm]
18.974” [48.194 cm]

842496A1.cdr
Figure 3-3: Horizontal mounting (enhanced and graphical front panels)

18.370”
[466,60 mm]
0.280”
[7,11 mm]
Typ. x 4
CUT-OUT
7.13” 4.000”
[181.1 mm] [101,60 mm]
17.750”
[450,85 mm] 842808A2.CDR

Figure 3-4: Horizontal dimensions and mounting (basic front panel)

HORIZONTAL TOP VIEW (19” 4RU) REMOTE MOUNTING
VIEW FROM REAR OF PANEL
BEZEL OUTLINE
8x0.156”
(9.5 mm)
0.375”
(3.962 mm)
(47.6 mm)
10.90”
1.875”
8.97”
(227.8 mm) (276.8 mm)
9.80”
(248.9 mm) 6.960”
(9.5 mm)
0.375”
(176.8 mm)
(121.5 mm)
4.785”
0.375”
17.52” Brackets repositioned (9.5 mm)
(445.0 mm) for switchgear mounting 5.000” 0.375”
(127.0 mm)
9.520” (9.5 mm)
14.520” (241.8 mm)
HORIZONTAL PANEL MOUNTING

4x0.28”
(368.8 mm)
17.720”
(450.1 mm)
3
18.37” (7.1 mm
(466.6 mm) diameter)
HORIZONTAL FRONT VIEW
CUTOUT
7.13” 4.00”
(181.1 mm) (101.6 mm) 7.00”
(177.8 mm)
17.75” 19.00”
(450.8 mm) (482.6 mm)
827704B5.cdr
Figure 3-5: Horizontal dimensions (graphical front panel)
11.093”
[281,76 mm]
9.687 “
[246,05 mm]
6.995” 6.960”
[177,67 mm] [176,78 mm]
18.974”
[481,94 mm]
862700A1.cdr

Figure 3-6: Horizontal dimensions (IP54 mounting collar)
MOUNTING PANEL
1.3” [3.3 cm]
3 16.00” [40.64 cm]

Ø 0.200
6 PLACES
8.34”
[21.18 cm]
7.65”
[19.43 cm]
20.19” [51.28 cm]
IP54 COLLAR
NOTES
1. INSPECT THE COLLAR BEFORE INSTALLATION, VERIFY GASKET IS ADHERED TO THE METAL ON ALL SIDES
2. MAKE SURE THE RELAY IS POSITIONED CENTER TO THE CUT OUT
3. INSTALL IP-54 COLLAR, CONFIRM THE GASKET PROPERLY MATES WITH THE PANEL ON ALL SIDES
SECURE USING #8-32 HEX NUT AT 6 PLACES. 842497A1.cdr
3.2.1 Rear terminal layout

The rear terminals depend on order code. An example is shown.

Ground
Model: B90D00HCHF8AH6AM6BP8BX7A
B90
RATINGS:
Mods: NONE
Control Power: 88-300V DC @ 35W / 77-265V AC @ 35VA See manual
Bus Differential Relay Contact Inputs: 300 VDC Max 10mA
Wiring Diagram:
Inst. Manual: 1601-0115
Contact Outputs: Refer to Instruction Manual Serial Number: MAZB98000029
E83849 Firmware: D
GE Multilin Mfg. Date: NOV 26, 2012
- M A A B 9 7 0 0 0 0 9 9 -
PO Num: 600001234.56
Item Num:
LISTED
®
®
IND.CONT. EQ.
52TL - M A A B 9 7 0 0 0 0 9 9 -
X W V U T S R P N M L K J H G F D B
c b a c b a c b a c b a c b a c b a
b a
LK1
Tx1 1
1
2
Rx1
ACT1
2
3
LK2
3
Tx1
4
4
5
Tx2 b a
ACT2 5
3
1
1 6
2 LK3
2 6
3
Rx2 3 7
4
4 7
8
Tx2 ACT3 8
IN
Optional Optional Optional Optional Optional Optional CT/VT CPU module Power
direct contact CT/VT or contact CT/VT or contact module (T module shown) supply
input/output input/output contact input/output contact input/output module
module module input/output module input/output module
module module
836790A1.CDR
Do not touch any rear terminals while the relay is energized, else death or serious injury can
result from electrical shock.
Small form-factor pluggable ports (SFPs) are pluggable transceivers. They transmit, receive, and
convert electrical signals to optical signals and vice-versa. Supplied with the device, they are inserted
into the Ethernet ports on the CPU module. A photo in the Maintenance chapter shows this plug-in
device. Do not use non-validated transceivers or install validated transceivers in the wrong Ethernet
slot, else damage can occur.
Terminal number assignments are three characters long and assigned by module slot position, row number, and column
letter. Two-slot wide modules take their slot designation from the first slot position (nearest to CPU module), indicated by
an arrow on the terminal block. The figure shows an example of rear terminal assignments.

Figure 3-7: Example of modules in F and H slots
J H G F Slot position
c b a c b a Column letter
Torque 9 inch-pounds
1 H1c H1b H1a F1c F1b F1a 1 Row number

Torque 19 ±1 inch-pounds
2 H2c H2b H2a F2c F2b F2a 2
3 6 H6c H6b H6a F6c F6b F6a 6
842761A2.CDR
The torque used to connect the screws that connect the terminal blocks (top screws a, b, c) and the metal plates over
empty slots to the chassis is 9 inch-pounds. For the screws used to wire the terminal blocks (rows 1 to 8), use 19±1 inch-
pounds.
The CPU module type depends on order code. During manufacturing, the power supply and CPU modules are installed in
slots B and D of the chassis with 13 inch-pounds of torque on the screws at the top and bottom of the modules. Wire
connections to these two modules at 13 inch-pounds.
Figure 3-8: CPU modules and power supply
RS485 Ethernet (3) RS485 Ethernet (3) RS485 Ethernet (3) RS485 Ethernet (3) Power
b a
LK1 LK1 LK1
RJ-45 1
LC copper 1
fiber 2
2
ACT1 ACT1 ACT1 Link, 3
LK2 LK2 LK2 Activity 3
4
4
5
b a
ACT2
b a
ACT2
b a
ACT2
b a 5
1
1
1
1
1
1
1
1 6
2 LK3 2 LK3 2 LK3 2
2 2 2 2 6
3 3 3 3
3 3 3 3 7
4 4 4 4
7
BNC
4 4 4 4
ST 8
for ACT3 ACT3 ACT3 fiber 8
IRIG-B
IN IN IN IN
T CPU module U CPU module V CPU module W CPU module Power supply
module
859758A1.CDR
The following figure shows the optical connectors for CPU modules.

Figure 3-9: LC fiber connector (left) and ST fiber connector (right)

WIRING CHAPTER 3: INSTALLATION
3.3 Wiring
3.3.1 Typical wiring
Figure 3-10: B90 is a multi-IED protection system
A B C
IA5 F1a
IA F1b
IA1 F1c
F1
IB5 F2a IA5 F1a
IB F2b
3
IA F1b
IB1 F2c IA1 F1c
IC5 F3a IB5 F2a
F3b IA5 F1a
IC IB F2b
F3c IA F1b
IC1 IB1 F2c
IA1 F1c
IG5 F4a IC5 F3a
CURRENT INPUTS
F4b IB5 F2a

IG IC F3b
IB F2b
IG1 F4c
IINPUTS
NPUTS
TS
IC1 F3c
8H
IB1 F2c
CURRENT INPU
IA5 F5a IG5 F4a
F5b IC5 F3a
IA
8H
IG
CURRENT
F4b
8
B90 Bus Differential IA1 F5c IC F3b

Protection System IG1 F4c
CURRENT INPUTS
F6a IC1 F3c
IB5 IA5 F5a
F6b IG5 F4a
IB IA F5b
8H
F6c IG F4b
IB1 IA1 F5c
F7a IG1 F4c
IC5 IB5 F6a
IED 1 F7b IA5 F5a
IC IB F6b
F7c IA F5b
IC1 IB1 F6c
IA1 F5c
IC5 F7a
IB5 F6a
IED 2 IC F7b
IB F6b
IC1 F7c
IB1 F6c
IC5 F7a
IED 3
IED IC F7b
IC1 F7c
I F1a
6H
F1 F1b
V
F1c
I F2a
F2 F2b
V
F2c
I F3a
F3 F3b
V
F3c
I F4a
F4 F4b
V
F4c
I F5a
F5 F5b
CONTACT INPUTS AND OUTPUTS
V
F5c
I F6a
F6 F6b
V
F6c
CONTACT INPUT F7a F7a
B90 Bus Differential CONTACT INPUT F7c F7c
Protection System CONTACT INPUT F8a F8a
CONTACT INPUT F8c F8c
COMMON F7b F7b
SURGE F8b
IED 4
836780A3.CDR

CHAPTER 3: INSTALLATION WIRING
The wiring diagrams on the next four pages are based on the following order code:
B90-H02-HCL-F8H-H6H-L8H-N6A-S8H-U6H-W7H.
The purpose of these diagrams is to provide examples of how the B90 is typically wired, not
specifically how to wire your own relay. See the sections following the wiring diagrams for examples
on connecting your relay correctly based on your relay configuration and order code.

Figure 3-11: Typical wiring diagram (Phase A; T module shown for CPU)
A
IED2 RX1
IED4 RX2
IED4 TX1
IED2 TX2
NOTE: This diagram is based on the following order code: F1a
Tx1 Rx1 Tx2 Rx2 IA5 F1
B90-T02-HCL-F8H-H6H-L8H-N6A-S8H-U6H-W7H
This diagram provides an example of how the device IA F1b
FIBER FIBER
is wired, not specifically how to wire the device. Please CHANNEL 1 CHANNEL 2 IA1 F1c
refer to the Instruction Manual for additional details on B90 COMMUNICATIONS W7H
wiring based on various configurations. IB5 F2a
F2
IB F2b
IB1 F2c
IC5 F3a
F3
IC F3b
IC1 F3c
B90 BUS DIFFERENTIAL RELAY IG5 F4a

F4
IG F4b
CURRENT INPUTS
IED 1 IG1 F4c
8H
(PHASE A PROTECTION) IA5 F5a
F5
IA F5b
IA1 F5c
H1a
3
I
IB5 F6a
F6
6H
H1b H1
V
H1c IB F6b
H2a I
H2 IB1 F6c
H2b
V
H2c F7a
IC5 F7
H3a I
H3b H3 IC F7b
V
H3c
H4a I IC1 F7c
H4b H4
V IG5 F8a
H4c F8
H5a I IG F8b
H5b H5
V
H5c IG1 F8c
H6a I
H6b H6
DIGITAL INPUTS/OUTPUTS
V
H6c IA5 L1a F9
H7a CONTACT INPUT H7a
H7c CONTACT INPUT H7c IA L1b
IA1 L1c
H8c CONTACT INPUT H8c
H7b COMMON H7b IB5 L2a F10
H8b SURGE
IB L2b
U1a I
L2c
6H
U1b U1 IB1
V
U1c L3a
U2a I
IC5 F11
U2b U2 IC L3b
V
U2c
U3a I IC1 L3c
U3b U3
V IG5 L4a F12
U3c
U4a I
IG L4b
U4 CURRENT INPUTS
U4b V
U4c IG1 L4c
8H
U5a I
U5 IA5 L5a F13
U5b V
U5c IA L5b
U6a I
U6 L5c
U6b V
IA1
Wet U6c
IB5 L6a
U7a CONTACT INPUT U7a F14
U7c CONTACT INPUT U7c
IB L6b
U8a CONTACT INPUT U8a
U8c CONTACT INPUT U8c IB1 L6c
U7b COMMON U7b
IC5 L7a
U8b SURGE F15
IC L7b
N1a
6A
I
N1b N1
L7c
V IC1
N1c
N2a I IG5 L8a
N2b N2
F16
V
N2c IG L8b
N3a L8c
IG1
N3b N3
N3c
N4a
N4b N4 IA5 S1a F17
Dry N4c
IA S1b
N5a CONTACT INPUT N5a
N5c CONTACT INPUT N5c IA1 S1c
N6c CONTACT INPUT N6c IB5 S2a F18
N5b COMMON N5b

IB S2b
S2c
( DC ONLY )
N7c CONTACT INPUT N7c IB1

IC5 S3a F19
N8c CONTACT INPUT N8c
N7b COMMON N7b IC S3b
N8b SURGE
IC1 S3c
* Optic
Fibre Tx1 100BaseFX
PORT 1 IG5 S4a F20
T
Rx1
Tx2 100BaseFX IG S4b

CURRENT INPUTS
Rx2
PORT 2
Tx3 100BaseFX IG1 S4c

Shielded PORT 3
8H
Ground at Rx3
twisted pairs
Remote
D1a
IA5 S5a F21
Device
RS485
D2a COM 2 IA S5b
D3a com
D4b IA1 S5c
Co-axial *
D4a IRIG-B
Input IB5 S6a
F22
CPU
Co-axial BNC
IB S6b
IB1 S6c
Co-axial * - For IRIG-B Input
B1b S7a
only use one CRITICAL IC5 F23
1
terminal as input B1a FAILURE

B2b IC S7b
B3a 48 VDC
OUTPUT IC1 S7c
B3b
DC
POWER SUPPLY
B5b HI IG5 S8a

B6b LO
CONTROL F24
AC or DC POWER
B6a IG S8b
B8a SURGE
IG1 S8c
B8b FILTER
No. 10AWG
Minimum
GROUND BUS
836785A1.CDR
MODULE ARRANGEMENT
MODULES MUST BE
GROUNDED IF X W V U T S R P N M L K J H G F D B
TERMINAL IS 7 6 8 6 8 6 8 9 1
PROVIDED
COM Inputs/ CT Inputs/ CT Inputs/ CT CPU Power
outputs outputs outputs Supply

Figure 3-12: Typical wiring diagram (Phase B; T module shown for CPU)
B
IED2 RX1
IED4 RX2
IED4 TX1
IED2 TX2
F1
NOTE: This diagram is based on the following order code: IA5 F1a
B90-T02-HCL-F8H-H6H-L8H-N6A-S8H-U6H-W7H Tx1 Rx1 Tx2 Rx2

FIBER FIBER
refer to the Instruction Manual for additional details on B90 COMMUNICATIONS W7H F2
IB F2b
IB1 F2c
F3
IC5 F3a
IC F3b
IC1 F3c
F4
IG F4b
CURRENT INPUTS
IED 2 IG1 F4c
F5
8H
(PHASE B PROTECTION) IA5 F5a
IA F5b
IA1 F5c
F6
H1a F6a
3
I
IB5
6H
H1b H1
V
H1c IB F6b
H2a I
H2 IB1 F6c
H2b
V
F7
H2c IC5 F7a
H3a I
H3b H3 IC F7b
V
H3c
H4a I IC1 F7c
H4
F8
H4b F8a
V IG5
H4c
H5a I IG F8b
H5b H5
V
H5c IG1 F8c
H6a I
H6b H6 F9
V
H6c IA5 L1a
IA1 L1c
H8c CONTACT INPUT H8c F10
H7b COMMON H7b IB5 L2a
H8b SURGE
IB L2b
U1a I
L2c
6H
U1b U1 IB1
V F11
U1c L3a
IC5
U2a I
U2b U2 IC L3b
V
U2c
U3a IC1 L3c
I
F12
U3b U3
V IG5 L4a
U3c
U4a I
IG L4b
CURRENT INPUTS
U4b U4
V
U4c IG1 L4c
F13
8H
U5a I
U5 IA5 L5a
U5b V
U5c IA L5b
U6a I
U6 L5c
U6b V
IA1
Wet U6c F14
IB5 L6a
IB L6b
U7b COMMON U7b F15
IC5 L7a
U8b SURGE
IC L7b
N1a
6A
I
N1b N1
L7c
V IC1
N1c F16
N2a I IG5 L8a
N2b N2
V
N2c IG L8b
N3a L8c
IG1
N3b N3
N3c
N4a
F17
N4b N4 IA5 S1a
Dry N4c
IA S1b
N6a CONTACT INPUT N6a F18
N6c CONTACT INPUT N6c IB5 S2a
N5b COMMON N5b

IB S2b
S2c
( DC ONLY )
N7c CONTACT INPUT N7c IB1 F19

IC5 S3a
N8b SURGE
IC1 S3c F20
* Optic
Fibre Tx1 100BaseFX
PORT 1 IG5 S4a
T
Rx1

CURRENT INPUTS
Rx2
PORT 2
Tx3 100BaseFX IG1 S4c F21

Shielded PORT 3
8H
Ground at Rx3
twisted pairs
Remote IA5 S5a
Device D1a
RS485
D2a COM 2 IA S5b
D3a com
D4b IA1 S5c
Co-axial *
D4a IRIG-B F22
Input IB5 S6a
CPU
Co-axial BNC
IB S6b
IB1 S6c
Co-axial * - For IRIG-B Input F23
B1b S7a
only use one CRITICAL IC5
1

B2b IC S7b
B3a 48 VDC
OUTPUT IC1 S7c
B3b F24
DC
POWER SUPPLY
B5b HI IG5 S8a

CONTROL
B6b LO
AC or DC POWER
B6a IG S8b
B8a SURGE
IG1 S8c
B8b FILTER
No. 10AWG
Minimum
GROUND BUS
836786A1.CDR
MODULE ARRANGEMENT
MODULES MUST BE
TERMINAL IS 7 6 8 6 8 6 8 9 1
PROVIDED

Figure 3-13: Typical wiring diagram (Phase C; T module shown for CPU)
C
IED2 RX1
IED4 RX2
IED4 TX1
IED2 TX2
F1
NOTE: This diagram is based on the following order code: IA5 F1a
B90-T02-HCL-F8H-H6H-L8H-N6A-S8H-U6H-W7H Tx1 Rx1 Tx2 Rx2

FIBER FIBER F2
refer to the Instruction Manual for additional details on B90 COMMUNICATIONS W7H
IB F2b
F3
IB1 F2c
IC5 F3a
IC F3b
F4
IC1 F3c
IG F4b
CURRENT INPUTS
F5
IED 3 IG1 F4c
8H
(PHASE C PROTECTION) IA5 F5a
IA F5b
F6
IA1 F5c
3
H1a I
IB5 F6a
6H
H1b H1
V
H1c IB F6b
H2a I F7
H2 IB1 F6c
H2b
V
H2c IC5 F7a
H3a I
H3b H3 IC F7b
V
H3c F8
H4a I IC1 F7c
H4b H4
V IG5 F8a
H4c
H5a I IG F8b
H5b H5
V
H5c IG1 F8c
H6a I
F9
H6b H6
V
H6c IA5 L1a
F10
IA1 L1c
H7b COMMON H7b IB5 L2a
H8b SURGE
IB L2b
U1a I F11
L2c
6H
U1b U1 IB1
V
U1c L3a
IC5
U2a I
U2b U2 IC L3b
V
U2c F12
U3a I IC1 L3c
U3b U3
V IG5 L4a
U3c
U4a I CURRENT INPUTS IG L4b
U4b U4 F13
V
U4c IG1 L4c
8H
U5a I
U5 IA5 L5a
U5b V
U5c IA L5b
U6a I
F14
U6 L5c
U6b V
IA1
Wet U6c
IB5 L6a
IB L6b
F15
U7b COMMON U7b
IC5 L7a
U8b SURGE
IC L7b
N1a
6A
I
N1b N1 F16
V IC1 L7c
N1c
N2a I IG5 L8a
N2b N2
V
N2c IG L8b
N3a L8c
IG1
N3b N3 F17
N3c
N4a
N4b N4 IA5 S1a
Dry N4c
IA S1b
N6c CONTACT INPUT N6c IB5 S2a
N5b COMMON N5b

IB S2b
S2c
( DC ONLY )
N7c CONTACT INPUT N7c IB1

IC5 S3a
F20
N8b SURGE
IC1 S3c
* Optic
Fibre Tx1 100BaseFX
PORT 1 IG5 S4a
T
Rx1

CURRENT INPUTS
Rx2
PORT 2 F21
Tx3 100BaseFX IG1 S4c
Shielded PORT 3
8H
Ground at Rx3
twisted pairs
Remote IA5 S5a
Device D1a
RS485
D2a COM 2 IA S5b
D3a com
F22
D4b IA1 S5c
Co-axial *
D4a IRIG-B
Input IB5 S6a
CPU
Co-axial BNC
IB S6b
F23
IB1 S6c
Co-axial * - For IRIG-B Input
B1b S7a
only use one CRITICAL IC5
1

B2b IC S7b
B3a 48 VDC F24
OUTPUT IC1 S7c
B3b
DC
POWER SUPPLY
B5b HI IG5 S8a

CONTROL
B6b LO
AC or DC POWER
B6a IG S8b
B8a SURGE
IG1 S8c
B8b FILTER
No. 10AWG
Minimum
GROUND BUS
836787A1.CDR
MODULE ARRANGEMENT
MODULES MUST BE
TERMINAL IS 7 6 8 6 8 6 8 9 1
PROVIDED

Figure 3-14: Typical wiring diagram (breaker fail and isolator monitoring; T module shown)
IED2 RX1
IED4 RX2
IED4 TX1
IED2 TX2
NOTE: This diagram is based on the following order code: H1a
6H
I
B90-T02-HCL-F8H-H6H-L8H-N6A-S8H-U6H-W7H H1b H1 Tx1 Rx1 Tx2 Rx2
V
This diagram provides an example of how the device H1c
H2a FIBER FIBER
is wired, not specifically how to wire the device. Please I
CHANNEL 1 CHANNEL 2
H2b H2
refer to the Instruction Manual for additional details on V
B90 COMMUNICATIONS W7H
H2c
wiring based on various configurations. H3a I
H3b H3
V
H3c
H4a I
H4b H4
V
H4c
H5a I
H5b H5
V
H5c

H6a I
H6b H6
V
H6c
3
H7b COMMON H7b
H8b SURGE I F1a
6H
U1a F1 F1b
6H
I
V
U1b U1 F1c
V
U1c I F2a
U2a I F2 F2b
V
U2b U2 F2c
V
U2c B90 BUS DIFFERENTIAL I F3a
U3a F3 F3b
U3b
I
U3 RELAY V
F3c
V
U3c I F4a
U4a I IED 4 (LOGIC) F4
V
F4b
U4b U4 F4c
V
U4c I F5a
U5a I F5
V
F5b
U5b U5 F5c

V
U5c I F6a

U6a I F6
V
F6b
Wet U6b U6 F6c
V
contact U6c CONTACT INPUT F7a F7a
U7a CONTACT INPUT U7a CONTACT INPUT F7c F7c
U7c CONTACT INPUT U7c CONTACT INPUT F8a F8a
U8a CONTACT INPUT U8a CONTACT INPUT F8c F8c
U8c CONTACT INPUT U8c COMMON F7b F7b
U7b COMMON U7b
SURGE L8b
U8b SURGE
N1a I L1a
6H
6A
I
N1b N1 L1 L1b
V V
N1c L1c
N2a I I L2a
N2b N2 L2 L2b
V V
N2c L2c
N3a I L3a
N3b N3 L3 L3b
V
N3c L3c
N4a I L4a
Dry N4b N4 L4 L4b
V
contact N4c L4c
N5a CONTACT INPUT N5a I L5a
N5c CONTACT INPUT N5c L5
V
L5b
N6a CONTACT INPUT N6a L5c

N6c CONTACT INPUT N6c I L6a

N5b COMMON N5b L6
V
L6b
L6c
CONTACT INPUT L7a L7a
( DC ONLY )

CONTACT INPUT L7c L7c
CONTACT INPUT L8a L8a
CONTACT INPUT L8c L8c
N7b COMMON N7b
COMMON L7b L7b
N8b SURGE
SURGE L8b
* Fiber
optic
Tx1 100Base-FX
PORT 1
T
Rx1 I S1a
6H
Tx2 100Base-FX S1 S1b

Rx2
PORT 2 V
S1c
Tx3 100Base-FX I S2a
Ground Shielded Rx3
PORT 3
at remote twisted pairs S2 S2b
V
device D1a S2c
RS485
D2a COM 2 I S3a
D3a COMMON S3 S3b
V
D4b S3c
Co-axial *
D4a IRIG-B I S4a
INPUT S4 S4b
CPU
Co-axial BNC V
S4c
I S5a
S5
V
S5b
Co-axial * - For IRIG-B input S5c
only use one terminal B1b

CRITICAL
1
I S6a
as input B1a FAILURE
B2b S6
V
S6b
B3a 48 V DC
S6c
B3b OUTPUT CONTACT INPUT S7a S7a
DC CONTACT INPUT S7c S7c
POWER SUPPLY
B5b HIGH
CONTROL CONTACT INPUT S8a S8a
B6b LOW
AC or DC POWER CONTACT INPUT S8c S8c
B6a
COMMON S7b S7b
B8a SURGE
B8b FILTER SURGE S8b
#10AWG
minimum 836788A1.CDR
GROUND BUS
MODULE ARRANGEMENT
X W V U T S R P N M L K J H G F D B
MODULES MUST 7 6 8 6 8 6 8 9 1
BE GROUNDED
IF TERMINAL COM Inputs/ CT Inputs/ CT Power
IS PROVIDED
Inputs/ CT CPU
outputs outputs outputs supply

3.3.2 Dielectric strength

Dielectric strength is the maximum electric strength that can be sustained without breakdown. It is measured in volts.
The table shows the dielectric strength of the UR-series module hardware.
Table 3-1: Dielectric strength of UR modules
Module type Module function Terminals Dielectric strength
From To
1 Power supply High (+); Low (+); (–) Chassis 2000 V AC for 1 minute
1 Power supply 48 V DC (+) and (–) Chassis 2000 V AC for 1 minute
1 Power supply Relay terminals Chassis 2000 V AC for 1 minute
2 Reserved N/A N/A N/A
3 3
4
Reserved
Digital contact inputs/
N/A
All
N/A
Chassis
N/A
2000 V AC for 1 minute
outputs
5 Analog inputs/outputs All except 8b Chassis < 50 V DC
6 Digital contact inputs/ All Chassis 2000 V AC for 1 minute
outputs
7 G.703 All except 2b, 3a, 7b, 8a Chassis 2000 V AC for 1 minute
RS422 All except 6a, 7b, 8a Chassis < 50 V DC
8 CT/VT All Chassis 2000 V AC for 1 minute
9 CPU All Chassis 2000 V AC for 1 minute
Filter networks and transient protection clamps are used in the hardware to prevent damage caused
by high peak voltage transients, radio frequency interference (RFI), and electromagnetic interference
(EMI). These protective components can be damaged by application of the ANSI/IEEE C37.90
specified test voltage for longer than the specified minute.
3.3.3 Control power
Power supplied to the relay must be connected to the matching power supply range of the relay. If
incorrect voltage is applied or voltage is applied to the wrong terminals, damage can occur.
The B90, like almost all electronic relays, contains electrolytic capacitors. These capacitors are well-
known to deteriorate over time if voltage is not applied periodically. Deterioration can be avoided by
powering up the relay at least once a year.
The power supply module is ordered with one of two possible voltage ranges, and the B90 can be ordered with or without
a redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges
are as follows (see the Specifications section of chapter 2 for details):
• Low (LO) range — 24 to 48 V (DC only) nominal
• High (HI) range — 125 to 250 V nominal
The power supply module provides power to the relay and supplies power for dry contact input connections.
The power supply module provides 48 V DC power for dry contact input connections and a critical failure relay (see the
Typical Wiring Diagram earlier). The critical failure relay is a form-C device that is energized once control power is applied
and the relay has successfully booted up with no critical self-test failures. If ongoing self-test diagnostic checks detect a
critical failure (see the Self-Test Errors section in chapter 7) or control power is lost, the relay de-energizes.
Connect all wires at be back of a UR before connecting to power, else death or serious injury can
result from electrical shock.

To connect power to the relay:

1. On the power supply module in the first slot, slot B, on the back of the device, connect the three wires to the terminals,
or connect two to the terminals and the third to the ground screw. 14 gauge stranded wire with disconnect devices is
recommended. Use 13 inch-pounds torque. Connect all wires to the relay before turning on power.
For high-reliability systems, the B90 has a redundant option in which two B90 power supplies are placed in parallel on the
bus. If one of the power supplies becomes faulted, the second power supply assumes the full load of the relay without any
interruptions. Each power supply has a green LED on the front of the module to indicate that it is functional. The critical fail
relay of the module also indicates a faulted power supply.
An LED on the front of the control power module shows the status of the power supply, as outlined in the table.
Table 3-2: Power supply LED on module
LED indication Power supply
Continuous on
On/off cycling
OK
Failure
3
Off Failure or no power
Figure 3-15: Control power connection
NOTE:
AC or DC 14 gauge stranded
wire with suitable
disconnect devices
is recommended.
Heavy copper conductor
or braided wire
B8b B8a B6a B6b B5b

+ +
– LOW HIGH
FILTER SURGE
CONTROL
POWER
Switchgear UR-series
ground bus protection system
827247A1.CDR
3.3.3.1 Non-volatile data storage

Non-volatile data is temporary data required after a power cycle for relay state, such as latch status before reboot. The
relay saves this data in non-volatile storage every two minutes or when a state change occurs.
If a state change occurs just before a power down (less than two minutes) and the relay power is cycled, some temporary
data can be saved and the prior state is retained at power up. Otherwise, a two-minute powered on period after a state
change ensures that all temporary state changes required after reboot have been saved. A command also is available to
initiate saving of data in the compact flash memory using Commands > Relay Maintenance > Save Volatile Data.
3.3.4 CT and VT modules

Information on the CT and VT modules for the B90 relay is shown here.
Verify that the connection made to the relay nominal current of 1 A or 5 A matches the secondary
rating of the connected CTs. Unmatched CTs may result in equipment damage or inadequate
protection.

Each AC current input has an isolating transformer and an automatic shorting mechanism that shorts the input when the
module is withdrawn from the chassis. There are no internal ground connections on the current inputs. Current
transformers with 1 to 50000 A primaries and 1 A or 5 A secondaries may be used.
Each B90 voltage input is intended for monitoring a single-phase voltage. The may include phase voltages or neutral
voltage from the open-delta VT.
All CT and VT modules are available with enhanced diagnostics. These modules can automatically detect CT/VT hardware
failure and take the relay out of service.
Substitute the tilde “~” symbol with the slot position of the module in the following figure.
Figure 3-16: CT/VT module wiring
3
~1a
~2a
~3a
~4a
~5a
~6a
~7a
~8a
~1b
~2b
~3b
~4b
~1c
~2c
~3c
~4c
~5c
~6c
~7c
~8c
VC
VB
VX
VA
IG
IG1
IC
IA
IB
VC
IC1
IA1
IB1
VB
IG5
VX
VA
IC5
IA5
IB5
Current inputs Voltage inputs

8F, 8G, 8L, and 8M modules (4 CTs and 4 VTs)
~1a
~2a
~3a
~4a
~5a
~6a
~7a
~8a
~1b
~2b
~3b
~4b
~5b
~6b
~7b
~8b
~1c
~2c
~3c
~4c
~5c
~6c
~7c
~8c
IG
IG
IG1
IG1
IC
IC
IA
IB
IA
IB
IC1
IC1
IA1
IB1
IA1
IB1
IG5
IG5
IC5
IC5
IA5
IB5
IA5
IB5
Current inputs
8H, 8J, 8N, and 8R modules (8 CTs)
~1a
~2a
~3a
~4a
~5a
~6a
~7a
~8a
~1b
~2b
~3b
~4b
~5b
~6b
~7b
~1c
~2c
~3c
~4c
~5c
~6c
~7c
~8c
IG
IG1
IC
IA
IC
IB
IA
IB
IC1
IA1
IC1
IB1
IA1
IB1
IG5
IC5
IA5
IC5
IB5
IA5
IB5
V
V
Current inputs Voltage

8K and 8S modules (7 CTs and 1 VT)
842803A2.CDR
3.3.5 Contact inputs and outputs

Nearly all contact input/output modules have 24 terminal connections. The connections are arranged typically as three
terminals per row, with eight rows in total. A given row of three terminals can be used for the outputs of one relay. For
example, for form-C relay outputs, the terminals connect to the normally open (NO), normally closed (NC), and common
contacts of the relay. For a form-A output, there are options of using current or voltage detection for feature supervision,
depending on the module ordered. The terminal configuration for contact inputs is different for the two applications.

The contact inputs are grouped with a common return. The input/output modules have three versions of grouping: four
inputs per common return, five inputs per common return on a high-density module, and two inputs per common return.
When a contact input/output module is ordered, four inputs per common is used. If the inputs must be isolated per row,
then two inputs per common return are selected (4D module). If the space limitation in the relay requires use of a high-
density input module (6W), five inputs share one common return and the module has six banks of inputs.
The tables and diagrams that follow illustrate the module types (6A and so on) and contact arrangements that can be
ordered for the relay. Since an entire row is used for a single contact output, the name is assigned using the module slot
position and row number. However, since there are two contact inputs per row, these names are assigned by module slot
position, row number, and column position.
Some form-A / solid-state relay outputs include circuits to monitor the DC voltage across the output contact when it is
open, and the DC current through the output contact when it is closed. Each of the monitors contains a level detector
whose output is set to logic “On = 1” when the current in the circuit is above the threshold setting. The voltage monitor is
set to “On = 1” when there is a voltage across open contact (the detector allows a current of about 1 to 2.5 mA), and the
current monitor is set to “On = 1” when the current flowing through the closed contact exceeds about 80 to 100 mA. The
voltage monitor is intended to check the health of the overall trip circuit, and the current monitor can be used to seal-in
3
the output contact until an external contact has interrupted current flow. If enabled, the current monitoring can be used as
a seal-in signal to ensure that the form-A contact does not attempt to break the energized inductive coil circuit and weld
the output contacts.
Block diagrams are shown as follows for form-A and solid-state relay outputs with optional voltage monitor, optional
current monitor, and with no monitoring. The actual values shown for contact output 1 are the same for all contact
outputs. Form-A contact output with or without a current or voltage monitoring option is not polarity sensitive. The polarity
shown in the figure is required for solid-state contact output connection.
Figure 3-17: Form-A and solid-state contact outputs with voltage and current monitoring
~#a ~#a
I I
~#b ~#b Load
V Load V
~#c + ~#c +
a) Voltage with optional
Voltage monitoring only Both voltage and current monitoring
current monitoring
~#a ~#a
V V
I ~#b I ~#b Load

Load
~#c + ~#c +
b) Current with optional
Current monitoring only Both voltage and current monitoring
voltage monitoring
(external jumper a-b is required)
~#a
~#b
Load
~#c +
c) No monitoring
827862A5.CDR
The operation of voltage and current monitors is reflected with the corresponding FlexLogic operands (CONT OP # VON, CONT
OP # VOFF, and CONT OP # ION) that can be used in protection, control, and alarm logic. The typical application of the voltage
monitor is breaker trip circuit integrity monitoring; a typical application of the current monitor is seal-in of the control
command.

See the Digital Elements section of chapter 5 for an example of how form-A and solid-state relay contacts can be applied
for breaker trip circuit integrity monitoring.
Consider relay contacts unsafe to touch when the unit is energized. Death or serious injury can
result from touching live relay contacts.
USE OF FORM-A AND SOLID-STATE RELAY OUTPUTS IN HIGH-IMPEDANCE CIRCUITS

For form-A and solid-state relay output contacts internally equipped with a voltage measuring circuit across the
contact, the circuit has an impedance that can cause a problem when used in conjunction with external high-input
impedance monitoring equipment, such as modern relay test set trigger circuits. These monitoring circuits can
continue to read the form-A contact as being closed after it has closed and subsequently opened, when measured
as an impedance.
The solution is to use the voltage measuring trigger input of the relay test set, and connect the form-A contact
3 through a voltage-dropping resistor to a DC voltage source. If the 48 V DC output of the power supply is used as a
source, a 500 Ω, 10 W resistor is appropriate. In this configuration, the voltage across either the form-A contact or
the resistor can be used to monitor the state of the output.
Where a tilde “~” symbol appears, substitute the slot position of the module. Where a number sign “#” appears,
substitute the contact number.
When current monitoring is used to seal-in the form-A and solid-state relay contact outputs, give the
FlexLogic operand driving the contact output a reset delay of 10 ms to prevent damage of the output
contact (in situations when the element initiating the contact output is bouncing, at values in the
region of the pickup value).
For high-density input/output modules 6W and 6X, use the following guidelines to connect. The new I/O modules use pin
type terminal blocks instead of the current ring type. The new terminals are required to achieve higher I/O count per
module.
• 12 to 24 AWG (3.3 mm2 to 0.2 mm2), single wire termination
• 16 to 24 AWG (1.31 mm2 to 0.2 mm2), multiple wire termination with matching wire sizes and stranding. Two wires
maximum per circuit.
• Suggested wiring screw tightening torque is a minimum 4.43 in-lb (0.5 Nm) and maximum 5.31 in-lb (0.6 Nm)
• Minimum suggested temperature rating for the conductors is 75°C
• Wire type: copper
Table 3-3: Contact input and output module assignments
~6A module ~6B module ~6C module ~6D module
Terminal Output or Terminal Output or Terminal Output Terminal Output
assignment input assignment input assignment assignment
~1 Form-A ~1 Form-A ~1 Form-C ~1a, ~1c 2 Inputs
~2 Form-A ~2 Form-A ~2 Form-C ~2a, ~2c 2 Inputs
~3 Form-C ~3 Form-C ~3 Form-C ~3a, ~3c 2 Inputs
~4 Form-C ~4 Form-C ~4 Form-C ~4a, ~4c 2 Inputs
~5a, ~5c 2 Inputs ~5 Form-C ~5 Form-C ~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs ~6 Form-C ~6 Form-C ~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7 Form-C ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8 Form-C ~8a, ~8c 2 Inputs

~6E module ~6F module ~6G module ~6H module

Terminal Output or Terminal Output Terminal Output or Terminal Output or
assignment input assignment assignment input assignment input
~1 Form-C ~1 Fast Form-C ~1 Form-A ~1 Form-A
~5a, ~5c 2 Inputs ~5 Fast Form-C ~5a, ~5c 2 Inputs ~5 Form-A
~6a, ~6c 2 Inputs ~6 Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-A
~7a, ~7c 2 Inputs ~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs
3
~6K module ~6L module ~6M module ~6N module
Terminal Output Terminal Output or Terminal Output or Terminal Output or
assignment assignment input assignment input assignment input
~1 Form-C ~1 Form-A ~1 Form-A ~1 Form-A
~2 Form-C ~2 Form-A ~2 Form-A ~2 Form-A
~3 Form-C ~3 Form-C ~3 Form-C ~3 Form-A
~4 Form-C ~4 Form-C ~4 Form-C ~4 Form-A
~5 Fast Form-C ~5a, ~5c 2 Inputs ~5 Form-C ~5a, ~5c 2 Inputs
~6 Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-C ~6a, ~6c 2 Inputs
~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs
~6P module ~6R module ~6S module ~6T module

Terminal Output or Terminal Output or Terminal Output or Terminal Output or
assignment input assignment input assignment input assignment input
~1 Form-A ~1 Form-A ~1 Form-A ~1 Form-A
~2 Form-A ~2 Form-A ~2 Form-A ~2 Form-A
~3 Form-A ~3 Form-C ~3 Form-C ~3 Form-A
~4 Form-A ~4 Form-C ~4 Form-C ~4 Form-A
~5 Form-A ~5a, ~5c 2 Inputs ~5 Form-C ~5a, ~5c 2 Inputs
~6 Form-A ~6a, ~6c 2 Inputs ~6 Form-C ~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs
~6U module ~6V module ~6W module 6X module

~1 Form-A ~1 Form-A ~1a - ~2a Output ~1a, ~1b 2 Inputs
~2 Form-A ~2 Form-A ~3a - ~4a Output ~2a, ~2b 2 Inputs
~3 Form-A ~3 Form-C ~5a - ~6a Output ~3a, ~3b 2 Inputs
~4 Form-A ~4 2 Outputs ~7a - ~8a Output ~4a, ~4b 2 Inputs
~5 Form-A ~5a, ~5c 2 Inputs ~9a - ~10a Output ~5a, ~5b 2 Inputs
~6 Form-A ~6a, ~6c 2 Inputs ~11a - ~12a Output ~7a, ~7b 2 Inputs

~6U module ~6V module ~6W module 6X module

~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~13a - ~14a Output ~8a, ~8b 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~15a - ~16a Output ~9a, ~9b 2 Inputs
--- --- --- --- ~17a - ~18a Output ~10a, ~10b 2 Inputs
--- --- --- --- ~1b - ~2b Output ~11a, ~11b 2 Inputs
3 --- --- --- --- ~13b - ~14b Output --- ---
--- --- --- --- ~15b - ~16b Output --- ---
--- --- --- --- ~17b - ~18b Output --- ---
~67 module ~4A module ~4B module ~4C module

Terminal Output Terminal Output Terminal Output Terminal Output
assignment assignment assignment assignment
~1 Form-A ~1 Not Used ~1 Not Used ~1 Not Used
~2 Form-A ~2 Solid-State ~2 Solid-State ~2 Solid-State
~4D module ~4L module

Terminal Output Terminal Output
assignment assignment
~1a, ~1c 2 Inputs ~1 2 Outputs
~8a, ~8c 2 Inputs ~8 Not Used

Figure 3-18: Contact input and output module wiring (Sheet 1 of 3)
842762A4.CDR


~ 1a ~ 5a CONTACT IN ~ 5a DIGITAL I/O 6L V ~ 1a ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6M V ~ 1a
6K
I I
~ 1b ~1 ~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 1c ~ 6a CONTACT IN ~ 6a ~ 1c ~ 8a CONTACT IN ~ 8a ~ 1c
~ 2a ~ 6c CONTACT IN ~ 6c V ~ 2a ~ 8c CONTACT IN ~ 8c V ~ 2a
I I
~ 2b ~2 ~ 5b COMMON ~ 5b ~2 ~ 2b ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c ~ 2c ~ 2c
~ 7a CONTACT IN ~ 7a ~ 8b SURGE
~ 3a ~ 3a ~ 3a
~ 7c CONTACT IN ~ 7c
~ 3b ~3 ~3 ~ 3b ~3 ~ 3b
~ 8a CONTACT IN ~ 8a
~ 3c ~ 3c ~ 3c
~ 4a ~ 4a ~ 4a
~ 7b COMMON ~ 7b
~ 4b ~4 ~4 ~ 4b ~4 ~ 4b
~ 4c ~ 8b SURGE ~ 4c ~ 4c
~ 5a ~ 5a
~ 5b ~5 ~5 ~ 5b
~ 5c ~ 5c
~ 6a ~ 6a
~ 6b ~6 ~6 ~ 6b
~ 6c ~ 6c
~ 7a
DIGITAL I/O
~ 7b ~7
~ 7c
~ 8a
~ 8b ~8
3
~ 8c
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6N V ~ 1a ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6P V ~ 1a

I I
~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 6a CONTACT IN ~ 6a ~ 1c ~ 8a CONTACT IN ~ 8a ~ 1c
~ 6c CONTACT IN ~ 6c V ~ 2a ~ 8c CONTACT IN ~ 8c V ~ 2a
I I
~ 5b COMMON ~ 5b ~2 ~ 2b ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c ~ 2c
~ 7a CONTACT IN ~ 7a ~ 8b SURGE
V ~ 3a V ~ 3a
~ 7c CONTACT IN ~ 7c I I
~3 ~ 3b ~3 ~ 3b
~ 3c ~ 3c
V ~ 4a V ~ 4a
~ 7b COMMON ~ 7b I I
~4 ~ 4b ~4 ~ 4b
~ 8b SURGE ~ 4c ~ 4c
V ~ 5a
I
~5 ~ 5b
~ 5c
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6R ~ 1a V ~ 6a
I
~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~6 ~ 6b
~ 6a CONTACT IN ~ 6a ~ 1c ~ 6c
~ 6c CONTACT IN ~ 6c ~ 2a
~ 5b COMMON ~ 5b ~2 ~ 2b
~ 2c
~ 3a ~ 7a CONTACT IN ~ 7a DIGITAL I/O 6S ~ 1a
~3 ~ 3b ~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 3c ~ 8a CONTACT IN ~ 8a ~ 1c
~ 4a ~ 8c CONTACT IN ~ 8c ~ 2a
~ 7b COMMON ~ 7b
~4 ~ 4b ~ 7b COMMON ~ 7b ~2 ~ 2b
~ 8b SURGE ~ 4c ~ 2c
~ 8b SURGE
~ 3a
~3 ~ 3b
~ 3c
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6T ~ 1a ~ 4a
~ 5c CONTACT IN ~ 5c ~1 ~ 1b ~4 ~ 4b
~ 6a CONTACT IN ~ 6a ~ 1c ~ 4c
~ 6c CONTACT IN ~ 6c ~ 2a ~ 5a
~ 5b COMMON ~ 5b ~2 ~ 2b ~5 ~ 5b
~ 2c ~ 5c
~ 3a ~ 6a
~3 ~ 3b ~6 ~ 6b
~ 3c ~ 6c
~ 4a
~ 7b COMMON ~ 7b
~4 ~ 4b
~ 8b SURGE ~ 4c
~ 7a CONTACT IN ~ 7a DIGITAL I/O 6U ~ 1a
~ 7c CONTACT IN ~ 7c ~1 ~ 1b
~ 8a CONTACT IN ~ 8a ~ 1c
~ 5a CONTACT IN ~ 5a DIGITAL I/O 6V V ~ 1a
I ~ 8c CONTACT IN ~ 8c ~ 2a
~ 5c CONTACT IN ~ 5c ~1 ~ 1b
~ 7b COMMON ~ 7b ~2 ~ 2b
~ 2c
~ 6c CONTACT IN ~ 6c V ~ 2a ~ 8b SURGE
I ~ 3a
~ 5b COMMON ~ 5b ~2 ~ 2b
~3 ~ 3b
~ 2c
~ 3a
~ 7c CONTACT IN ~ 7c ~ 4a
~3 ~ 3b
~ 8a CONTACT IN ~ 8a ~4 ~ 4b
~ 3c
~ 8c CONTACT IN ~ 8c ~ 4c
~ 4a
~ 7b COMMON ~ 7b ~ 4a ~ 5a
~ 4b
~ 4c ~5 ~ 5b
~ 8b SURGE ~ 4c
~ 5c
~ 6a
~6 ~ 6b
~ 6c
842763A2.CDR


DIGITAL I/O 6W DIGITAL I/O 6X
~ 1b CONTACT IN ~ 16 CONTACT IN ~ 1 ~ 1a ~ 1b ~ 1a
~ 10 ~ 1
~ 11 ~ 2
~ 12 ~ 3
~ 6b COMMON COMMON ~ 6a ~ 6b ~ 6a
~ 7b ~ 7a
~ 7b CONTACT IN ~ 21 CONTACT IN ~ 6 ~ 7a ~ 13 ~ 4
~ 8b ~ 8a
~ 8b CONTACT IN ~ 22 CONTACT IN ~ 7 ~ 8a
~ 9b ~ 9a
~ 9b CONTACT IN ~ 23 CONTACT IN ~ 8 ~ 9a ~ 14 ~ 5
~10b ~ 10a
~10b CONTACT IN ~ 24 CONTACT IN ~ 9 ~10a ~11b ~ 11a
~11b CONTACT IN ~ 25 CONTACT IN ~ 10 ~11a ~ 15 ~ 6
~12b ~ 12a
~12b COMMON COMMON ~12a ~13b ~ 13a
~ 16 ~ 7
~ 13b CONTACT IN ~ 26 CONTACT IN ~ 11 ~ 13a ~14b ~ 14a
~ 17 ~ 8
~ 18 ~ 9
~18b COMMON COMMON ~18a
859759A1.CDR
For proper functionality, observe the polarity shown in the figures for all contact input and output 3
connections.
3.3.5.1 Contact inputs

A dry contact has one side connected to terminal B3b. This is the positive 48 V DC voltage rail supplied by the power supply
module. The other side of the dry contact is connected to the required contact input terminal. Each contact input group
has its own common (negative) terminal that must be connected to the DC negative terminal (B3a) of the power supply
module. When a dry contact closes, a current of 1 to 3 mA flows through the associated circuit.
A wet contact has one side connected to the positive terminal of an external DC power supply. The other side of this
contact is connected to the required contact input terminal. If a wet contact is used, then the negative side of the external
source must be connected to the relay common (negative) terminal of each contact group. The maximum external source
voltage for this arrangement is 300 V DC.
The voltage threshold at which each group of four contact inputs detects a closed contact input is programmable as
17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources.
Figure 3-21: Dry and wet contact input connections
Terminals from type 6B Terminals from type 6B
(Dry) contact input/output module (Wet) contact input/output module
~7a Contact input 1 ~7a Contact input 1
~7c Contact input 2 ~7c Contact input 2
~8a Contact input 3 24 to 250 V ~8a Contact input 3
~8c Contact input 4 ~8c Contact input 4
~7b Common ~7b Common
~8b Surge ~8b Surge
B1b
B1a Critical failure
B2b
Power supply module
B3a
48 V DC output
B3b
B5b HI+
B6b LO+ Control power
B6a
B8a Surge
B8b Filter
827741A5.CDR
Where a tilde “~” symbol appears, substitute the slot position of the module.

There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recommend
using an external DC supply.
3.3.5.2 General application considerations

Contacts outputs of protective relays, auxiliary contacts from breakers, disconnectors and other devices are connected
generally to contacts inputs of protective relays. In some situations, the contact outputs of some protective relays can
have high impedance connected across it. When such a contact output is connected across a B90 contact input, it can
spuriously operate the B90 input even when the output is open, if there is a substantial distributed capacitance
(represented by C1) present in the wiring between the output and the B90 input, and the debounce time setting in the B90
relay is low enough. This false assertion of the contact input, when there is inadvertent ground present at the DC positive
terminal, can be prevented by inserting a resistor across the B90 input.
The following figure shows a typical DC circuit, with battery ground detection, of contact input. The contact output has
parallel impedance across it (represented by R1).
3 Figure 3-22: Typical contact input DC circuit
Contact Input
859755A1.cdr
The presence of the impedance path (R1) across the contact output allows the stray (distributed) capacitance C1 to charge
as shown, thus developing a voltage across the contact input enough to momentarily operate the input while the
capacitance discharges in the presence of DC ground on the positive terminal of the battery.
The duration of the discharge depends on the value of the distributed capacitance, the initial voltage of the distributed
capacitance, and the input impedance of the contact input. If the duration is greater than the debounce time setting, then
the contact input operates.
The application example that follows describes how to mitigate this issue by connecting a resistor across the contact
input, as shown in the next figure, or by adjusting the debounce time setting to a value greater than the discharge time to
prevent spurious operation of the contact input only if the voltage (with output open) across the contact input due to trickle
current is less than the threshold voltage. This operation of contact inputs also can be prevented by using the Auto-Burnish
contact inputs or contact inputs with active impedance.

Figure 3-23: Contact input connected to a contact output with resistor (R2) across the input
Contact Input
3
859756A1.cdr
Application example
This example is for illustrative purposes only and the calculations present the worst-case scenario. In practice, the value of
debounce time can be lower.
Contact input ON state impedance used in the calculation of the discharge period is based on the following table.
Table 3-4: Discharge period
Battery voltage (V) Input impedance (kΩ)
130 50
250 97
Debounce time setting = 2 ms

Assume a stray capacitance of 0.1 μF.
Assume an initial voltage across the stray capacitance "Vinitial" = 19 V (Vthreshold - 65 V), where Vthreshold = 84 V. The
initial voltage Vinitial depends on values of impedance of R1 and contact inputs when the contact input is OFF (non-
activated state).
Therefore, discharge time constant (τ) =50 kΩ *0.1 μF = 5 ms.
Discharge period t is calculated from the following equation:
Vthreshold = (Vbatt - VInitial) *e^ (-t/τ)
84 = -149 *e^ (t/0.005) Eq. 3-1
T = -0.005 * ln (84/149) = 0.0029 s
Therefore, in this example the contact inputs operate.
To prevent this operation, the debounce time must be increased to 4 ms (set debounce time as per the following table) or
insert a resistor less than or equal to "R" as calculated later.
Table 3-5: Typical debounce time setting
Stray capacitance (μF) Battery voltage (V) Debounce time (ms)
0.05 130 2
0.1 130 4
0.2 130 6
0.05 250 3

Stray capacitance (μF) Battery voltage (V) Debounce time (ms)

0.1 250 6*
0.2 250 11
* Default debounce time on contact inputs is 6 ms.

The value of this resistor "R" is calculated as follows:
1. Determine the minimum voltage (V threshold) required to turn on the input. This is determined by direct measurement
or referenced in the input specifications.
2. Calculate the resistance necessary to limit the voltage to 1/3 V threshold (when the contact is OFF, the non-activated
state) as follows:
R = (Vthreshold / 3) / (2 mA) Eq. 3-2
The 2 mA current is used in case the contact input is connected across the GE Form A contact output with voltage
3 monitoring. Otherwise use the amperage of the active circuit connected to the contact input when its contact output
is open and the voltage across the contact input is third trigger threshold to calculate the resistor value.
3. When the contact is ON (operate state), the battery voltage appears across the resistor. The wattage rating of the
resistor is then:
PR = 1.3 * (Vbatt) ^2 / R Watts Eq. 3-3
4. Applying the following equation to our example:
R = 84 V / 3 * (1 / 2 mA) = 14 kΩ
PR = 1.57 Watts Eq. 3-4
5. Calculating the voltage across the contact input with the Burden Resistor, Voltage across the contact Input:
Vresistor = 2 mA * 14 Kohm = 28 V
Vresistor < contact input threshold (84 V) Eq. 3-5
In conclusion, in this example, the contact input does NOT operate falsely with the Burden Resistor across its input AND
when a battery ground is present.
3.3.5.3 Use of contact inputs with auto-burnishing

The contact inputs sense a change of state of the external device contact based on the measured current. When external
devices are located in a harsh industrial environment (either outdoor or indoor), their contacts can be exposed to various
types of contamination. Normally, there is a thin film of insulating sulfidation, oxidation, or contaminates on the surface of
the contacts, sometimes making it difficult or impossible to detect a change of state. This film must be removed to
establish circuit continuity — an impulse of higher than normal current can accomplish this.
The contact inputs with auto-burnish create a high current impulse when the threshold is reached to burn off this oxidation
layer as a maintenance to the contacts. Afterwards the contact input current is reduced to a steady-state current. The
impulse has a five-second delay after a contact input changes state.
Figure 3-24: Current through contact inputs with auto-burnishing
Current
50 to 70 mA
3 mA
Time
25 to 50 ms
842749A1.CDR

Regular contact inputs limit current to less than 3 mA to reduce station battery burden. In contrast, contact inputs with
auto-burnishing allow currents up to 50 to 70 mA at the first instance when the change of state is sensed. Then, within 25
to 50 ms, this current is slowly reduced to 3 mA as indicated. The 50 to 70 mA peak current burns any film on the contacts,
allowing for proper sensing of state changes. If the external device contact is bouncing, the auto-burnishing starts when
external device contact bouncing is over.
Another important difference between the auto-burnishing input module and the regular input modules is that only two
contact inputs have common ground, as opposed to four contact inputs sharing one common ground (see the Contact
Input and Output Module Wiring diagrams). This is beneficial when connecting contact inputs to separate voltage sources.
Consequently, the threshold voltage setting is also defined per group of two contact inputs.
The auto-burnish feature can be disabled or enabled using the DIP switches found on each daughter card. There is a DIP
switch for each contact, for a total of 16 inputs.
Figure 3-25: Auto-burnish DIP switches
CONTACT INPUT 1 AUTO-BURNISH = OFF

3
CONTACT INPUT 1 AUTO-BURNISH = ON



842751A1.CDR
The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the auto-burnish
functionality using an oscilloscope.
3.3.5.4 Use of contact inputs with active impedance

Contact inputs can be susceptible to parasitic capacitance, caused by long cable runs affected by switching surges from
external circuits. This can result in inadvertent activation of contact inputs with the external contact open. In this case, GE
recommends using the contact I/O module with active impedance circuit.
Active impedance contact input can tolerate external cable capacitance of up to 0.2 µF, without entering the ON state for
more than 2 ms. The contact input debounce time can still be set above 2 ms for added security to prevent contact input
activations caused by external transient ON states.
An active impedance contact input is normally in Low impedance mode during OFF contact state (non-activated
condition). During Low impedance state, contact input impedance is maintained at 10 K Ohms impedance to allow fast
discharge of the stray capacitance of the long cables.
When the contact input voltage exceeds the set threshold, active impedance maintains 10 K Ohms impedance. If voltage
starts rapidly decreasing, this indicates that stray capacitance is being discharged through the contact input. If, however,
voltage stabilizes above the set threshold, the input impedance is switched to High impedance mode of 100 K Ohms. This
value reduces the input current to <3 mA, and contact input switches to the ON state (operated state).
The figure shows the active impedance contact input V-I characteristic. Different thresholds with their corresponding
characteristics are shown by color. The contact input is in the ON (operated) state if the input voltage is to the right of the
colored threshold band (+/-10% tolerance), and the contact input is in the OFF (non-activated) state when input voltage is
to the left of the band. A contact input is in LOW state during non-operated system condition, and actively switches to
HIGH state upon detection of input voltage above the settable threshold.

Figure 3-26: Active impedance contact input V-I characteristic
30
84 V threshold
166 V threshold
17 V threshold
33 V threshold
e
at
st
e
25
nc
da
pe
im
w
Lo
20
3
Current (millamperes)
15
s
m
oh
K
10
10
166 V threshold
84 V threshold
33 V threshold
5
17 V threshold
dance state
100 K ohms HIgh impe
0
0 50 100 150 200 250 300
Voltage (Volts) 859757A2.vsd
3.3.6 RS232 port

On the enhanced and basic front panels is a nine-pin RS232C serial port for programming with a computer. All that is
required to use this interface is a computer running the EnerVista UR Setup software provided with the relay. Cabling for
the RS232 port is shown in the following figure for the nine-pin connector on the UR and nine or 25-pin connector on a
computer.
The baud rate for this port can be set, with a default of 115200 bps.

Figure 3-27: RS232 front panel port connection

Front panel 9 pin RS232 Program port
1: N/A
2: (TXD)
3: (RXD)
RELAY
PERSONAL 4: N/A
COMPUTER 5: (SGND) Signal Ground
FRONT PANEL
6: N/A
PROGRAM PORT 7: N/A
8: N/A
9: N/A
9 PIN
RS232 RS232
3
D CONNECTOR D CONNECTOR
URS232 INTERFACE COM1 OR COM2

SERIAL PORT
RELAY COMPUTER
1 1 8 827758A3.cdr
TXD 2 2 3 RXD
RXD 3 3 2 TXD
4 4 20
SGND 5 5 7 SGND
6 6 6
7 7 4
8 8 5
9 9 22
9 PIN 25 PIN
CONNECTOR CONNECTOR
3.3.7 CPU communication ports
3.3.7.1 Overview
There is a rear RS485 communication port on the CPU module. The CPU module does not require a surge ground
connection.

Figure 3-28: CPU module communications wiring

MM fiber-
Port 1
T
optic cable Tx1 Rx1 100Base-FX
Tx2 Rx2 100Base-FX Port 2
Shielded
twisted-pairs
D1a +
RS485
D2a —
COM2
Ground at D3a COMMON
remote D4b +
device
D4a — IRIG-B
input
CPU
BNC
Co-axial cable
U
100Base-TX Port 1
MM fiber-
optic cable Tx1 Rx1 100Base-FX Port 2
Shielded Tx2 Rx2 100Base-FX Port 3
twisted-pairs
D1a +
RS485
D2a —
COM2
remote D4b +
device
D4a — IRIG-B
input
CPU
BNC
Co-axial cable
Port 1
V
100Base-TX
100Base-TX Port 2
Shielded 100Base-TX Port 3
twisted-pairs
D1a +
RS485
D2a —
COM2
remote D4b +
device
D4a — IRIG-B
input
CPU
BNC
Co-axial cable
W
10/100Base-TX Port 1
MM fiber-
optic cable
Shielded Tx2 Rx2 100Base-FX Port 3
twisted-pairs
D1a +
RS485
D2a —
COM2
remote D4b +
device
D4a — IRIG-B
input
CPU
BNC
Co-axial cable
859774A1.CDR
3.3.7.2 RS485 port

RS485 data transmission and reception are accomplished over a single twisted-pair wire with transmit and receive data
alternating over the same two wires. Through the use of the port, continuous monitoring and control from a remote
computer, SCADA system, or Power Line Carrier (PLC) is possible.
To minimize errors from noise, the use of shielded twisted-pair wire is recommended. Correct polarity must be observed.
For instance, the relays must be connected with all RS485 “+” terminals connected together, and all RS485 “–” terminals
connected together. Though data is transmitted over a two-wire twisted pair, all RS485 devices require a shared reference,

or common voltage. This common voltage is implied to be a power supply common. Some systems allow the shield (drain
wire) to be used as common wire and to connect directly to the B90 COM terminal (#3); others function correctly only if the
common wire is connected to the B90 COM terminal, but insulated from the shield.
To avoid loop currents, ground the shield at only one point. If other system considerations require the shield to be
grounded at more than one point, install resistors (typically 100 ohms) between the shield and ground at each grounding
point. Each relay needs to be daisy-chained to the next one in the link. A maximum of 32 relays can be connected in this
manner without exceeding driver capability. For larger systems, additional serial channels must be added. It is also
possible to use commercially available repeaters to have more than 32 relays on a single channel. Avoid star or stub
connections entirely.
Lightning strikes and ground surge currents can cause large momentary voltage differences between remote ends of the
communication link. For this reason, surge protection devices are provided internally at both communication ports. An
isolated power supply with an optocoupled data interface also acts to reduce noise coupling. To ensure maximum
reliability, ensure that all equipment has similar transient protection devices installed.
Terminate both ends of the RS485 circuit with an impedance as shown in the figure. 3
Figure 3-29: RS485 serial connection
SCADA / PLC / computer UR-series device

Shield Twisted pair
ZT (*) RS485 +
Data Optocoupler Optocoupler Data
RS485 –
COM
COMP 485COM
Ground shield at SCADA / PLC /

computer only or at
UR-series device only Relay
RS485 +
ZT (*) Terminating impedance at
RS485 –
each end (typically 120 Ω and 1 nF)
COMP 485COM
Up to 32 devices,
maximum 4000 feet
(1200 m)
Relay
ZT (*)
RS485 +
RS485 –
COMP 485COM Last device

827757AA.CDR
3.3.7.3 100Base-FX fiber optic ports

The fiber-optic communication ports allow for fast and efficient communications between relays at 100 Mbps. Optical
fiber can be connected to the relay supporting a wavelength of 1310 nm in multimode.
Ensure that the dust covers are installed when the fiber is not in use. Dirty or scratched connectors can lead to high losses
on a fiber link.
3.3.8 IRIG-B
There is a round IRIG-B connector at the back of the CPU module, marked "IN". Use is optional.

DIRECT INPUT AND OUTPUT COMMUNICATIONS CHAPTER 3: INSTALLATION
IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The
IRIG-B code allows time accuracies of up to 100 ns. The GE MultiSync 100 1588 GPS Clock as well as third-party equipment
are available for generating the IRIG-B signal. This equipment can use a global positioning system (GPS) satellite system to
obtain the time reference so that devices at different geographic locations can be synchronized. The IRIG time code
formats are serial, pulse width-modulated codes that can be either DC level shifted or amplitude modulated (AM). Using
IRIG-B input, the B90 operates an internal oscillator with 1 µs resolution and accuracy.
Figure 3-30: Options for IRIG-B connection
GPS connection GPS satellite system
UR-series device
3 IRIG-B
4B IRIG-B (+)
4A IRIG-B (–)
time code generator
RG58/59 coaxial cable Receiver
(DC-shift or + BNC (in)
amplitude modulated
signal can be used)
GPS connection GPS satellite system
IRIG-B
time code generator
UR-series device
Twisted-pair cable
(DC-shift or +
4B IRIG-B (+)
amplitude modulated
4A IRIG-B (–)
signal can be used)
Receiver
BNC (in)
827756A8.CDR
Using an amplitude-modulated receiver causes errors up to 1 ms in event time stamping.
3.4 Direct input and output communications

3.4.1 Description
The direct inputs and outputs feature makes use of the type 7 series of communications modules and allows direct
messaging between UR devices. The communications modules are outlined in the table later in this section.

CHAPTER 3: INSTALLATION DIRECT INPUT AND OUTPUT COMMUNICATIONS
The communications channels are normally connected in a ring configuration, as shown in the following figure. The
transmitter of one module is connected to the receiver of the next module. The transmitter of this second module is then
connected to the receiver of the next module in the ring. This is continued to form a communications ring. The figure
illustrates a ring of four UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to
UR4-Rx, and UR4-Tx to UR1-Rx. A maximum of 16 URs can be connected in a single ring.
Figure 3-31: Direct input and output single-channel connection
Tx
UR 1
Rx
Tx
UR 2
Rx
UR 3
Tx 3
Rx
Tx
UR 4
Rx
842006A2.CDR
Inter-relay communication (IRC) modules with protocol C37.94 and G.703 are designed for back-to-back communication
connections, so the ring configuration shown in the previous figure does not apply. To establish inter-relay communication
in more than two URs, you need to have a two-channel IRC module and enable the DIRECT I/O CHANNEL CROSSOVER setting
in all relays, as shown in the next figure. This configuration can be expanded to 16 URs, and this configuration does not
provide a redundancy ring since both channels are made into a single ring by the channel crossover function. As per the
figure entitled Typical Pin Interconnection between Two G.703 Interfaces later in this chapter, the clock is supplied typically
by multiplexer (MUX) and all URs are in Loop Timing Mode. If there is no MUX, then UR1 and UR3 can be in Internal Timing
Mode and UR2 and UR4 can be in Loop Timing Mode. That is, connected channels must have opposite timing modes.
Figure 3-32: Ring configuration for C37.94 module (concept also applies to G.703)
Tx1 Tx2 Tx1 Tx2

MUX UR 1 MUX MUX UR 2 MUX
Rx1 Rx2 Rx1 Rx2
Tx1 Tx2 Tx1 Tx2

MUX UR 4 MUX MUX UR 3 MUX
Rx1 Rx2 Rx1 Rx2
842236A1.CDR
The interconnection for dual-channel type 7 communications modules is shown as follows. Two-channel modules allow for
a redundant ring configuration. That is, two rings can be created to provide an additional independent data path. The
required connections are: UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1 for the
first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the second ring.

Figure 3-33: Direct input and output dual-channel connection
Tx1
Rx1
UR 1
Tx2
Rx2
Tx1
Rx1
UR 2
Tx2
Rx2
3 Tx1
Rx1
UR 3
Tx2
Rx2
Tx1
Rx1
UR 4
Tx2
Rx2
842007A3.CDR
The following figure shows the connection for three UR-series relays using two independent communication channels. UR1
and UR3 have single type 7 communication modules; UR2 has a dual-channel module. The two communication channels
can be of different types, depending on the type 7 modules used. To allow the direct input and output data to cross-over
from channel 1 to channel 2 on UR2, set the DIRECT I/O CHANNEL CROSSOVER setting to “Enabled” on UR2. This forces UR2 to
forward messages received on Rx1 out Tx2, and messages received on Rx2 out Tx1.
Figure 3-34: Direct input and output single/dual channel combination connection
Tx
UR 1
Rx
Channel 1
Tx1
Rx1
UR 2
Tx2
Rx2
Channel 2
Tx
UR 3
Rx
842013A2.CDR
The inter-relay communications modules are available with several interfaces and some are outlined here in more detail.
Those that apply depend on options purchased. The options are outlined in the Inter-Relay Communications section of the
Order Code tables in Chapter 2. All of the fiber modules use ST type connectors.

3.4.2 Fiber: LED and ELED transmitters

The following figure shows the configuration for the 7A, 7B, 7C, 7H, 7I, and 7J fiber-only modules.
Figure 3-35: LED and ELED fiber modules
7A, 7B, and 7H, 7I, and
7C modules 7J modules
Rx1 Rx1
Tx1 Tx1
3
Rx2
Tx2
1 channel 2 channels
831719A3.CDR
3.4.3 Fiber laser transmitters

The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser modules.
Figure 3-36: 7x Laser fiber modules
72 and 7D 73 and 7K
modules modules
Tx1 Tx1
Rx1 Rx1
Tx2
Rx2
1 channel 2 channels
831720A5.CDR
The following figure shows configuration for the 2I and 2J fiber-laser modules.

Figure 3-37: 2I and 2J laser fiber modules

2I and 2J
modules
Rx1
Tx1
Rx2
3 Tx2
2 channels
831827A1.CDR
Observing any fiber transmitter output can injure the eye.
When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the
maximum optical input power to the receiver.
3.4.4 G.703 interface
3.4.4.1 Description
G.703 is an International Telecommunications Union (ITU) standard for the transmission of data and voice signals. Modules
7R (one channel) and 7S (two channels) apply.
The following figure shows the 64K ITU G.703 co-directional interface configuration. This is module 7S.
The G.703 module is fixed at 64 kbps. The SETTINGS  PRODUCT SETUP  DIRECT I/O  DIRECT I/O DATA RATE setting is not
applicable to this module.
AWG 24 twisted shielded pair wiring is recommended for external connections, with the shield grounded only at one end.
Connecting the shield to pin X1a or X6a grounds the shield since these pins are connected internally to ground. Thus, if
pin X1a or X6a is used to ground the shield at one end, do not ground the shield at the other end. This interface module is
protected by surge suppression devices.
Figure 3-38: G.703 interface configuration
Shield ~1a
7S
Tx – ~1b
G.703 Rx – ~2a
channel 1
Tx + ~2b
Rx + ~3a
G.703 communications
Surge ~3b
Shield ~6a
Tx – ~6b
G.703 Rx – ~7a
channel 2
Tx + ~7b
Rx + ~8a
Surge ~8b
842773A3.CDR

The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical
arrangement of these pins, see the Rear Terminal Layout section earlier in this chapter. All pin interconnections are to be
maintained for a connection to a multiplexer.
Figure 3-39: Typical pin interconnection between two G.703 interfaces
Shield X1a X1a Shield
7S
7S
Tx – X1b X1b Tx –
G.703 Rx – X2a X2a Rx – G.703
channel 1 channel 1
Tx + X2b X2b Tx +
Rx + X3a X3a Rx +
Surge X3b X3b Surge
Shield X6a X6a Shield
Tx – X6b X6b Tx –
G.703 Rx – X7a X7a Rx – G.703
channel 2 channel 2
3
Tx + X7b X7b Tx +
Rx + X8a X8a Rx +
Surge X8b X8b Surge
831727A5.CDR
Pin nomenclature differs from one manufacturer to another. It is not uncommon to see pinouts numbered TxA, TxB,
RxA, and RxB. In such cases, assume that “A” is equivalent to “+” and “B” is equivalent to “–.”
3.4.4.2 G.703 selection switch procedures

1. With the power to the relay off, remove the G.703 module (7R or 7S) as follows. Record the original location of the
module to help ensure that the same or replacement module is inserted into the correct slot.
2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release
the module for removal. (For more information on accessing modules, see the Maintenance chapter.)
3. Remove the module cover screw.
4. Remove the top cover by sliding it towards the rear and then lift it upwards.
5. Set the timing selection switches (channels 1 and 2) to the required timing modes.
6. Replace the top cover and the cover screw.
7. Re-insert the G.703 module. Take care to ensure that the correct module type is inserted into the correct slot position.
The ejector/inserter clips located at the top and bottom of each module must be in the disengaged position as the
module is inserted smoothly into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips
simultaneously. When the clips have locked into position, the module is inserted fully.

Figure 3-40: G.703 timing selection switch setting

Bottom cover
Ejector/inserter clip
FRONT
Channel 1
Timing selection
switches
Top cover
3
Channel 2
Cover screw
REAR
831774A3.CDR
Table 3-6: G.703 timing selections

Switches Function
S1 OFF octet timing disabled
ON octet timing 8 kHz
S5 and S6 S5 = OFF and S6 = OFF loop timing mode
S5 = ON and S6 = OFF internal timing mode
S5 = OFF and S6 = ON minimum remote loopback mode
S5 = ON and S6 = ON dual loopback mode
3.4.4.3 G.703 octet timing

If octet timing is enabled (ON), this 8 kHz signal is asserted during the violation of bit 8 (LSB) necessary for connecting to
higher order systems. When B90s are connected back-to-back, octet timing is disabled (OFF).
3.4.4.4 G.703 timing modes

There are two timing modes for the G.703 module: internal timing mode and loop timing mode (default).
• Internal Timing Mode — The system clock is generated internally. Therefore, set the G.703 timing selection to internal
timing mode for back-to-back (UR-to-UR) connections. For back-to-back connections, set octet timing (S1 = OFF) and
timing mode to internal timing (S5 = ON and S6 = OFF).
• Loop Timing Mode — The system clock is derived from the received line signal. Therefore, set the G.703 timing
selection to loop timing mode for connections to higher order systems. For connection to a higher order system (UR-
to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 =
OFF).
The switch settings for the internal and loop timing modes are shown.

Figure 3-41: Switches

Loop timing mode
Internal timing mode (factory default)
842752A2.CDR
3.4.4.5 G.703 test modes

In minimum remote loopback mode, the multiplexer is enabled to return the data from the external interface without any
processing to assist in diagnosing G.703 line-side problems irrespective of clock rate. Data enters from the G.703 inputs,
passes through the data stabilization latch that also restores the proper signal polarity, passes through the multiplexer,
and then returns to the transmitter. The differential received data is processed and passed to the G.703 transmitter module
3
after which point the data is discarded. The G.703 receiver module is fully functional and continues to process data and
passes it to the differential Manchester transmitter module. Since timing is returned as it is received, the timing source is
expected to be from the G.703 line side of the interface.
Figure 3-42: G.703 minimum remote loopback mode
DMR = Differential Manchester Receiver

DMR G7X DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver
DMX G7R
842774A1.CDR
In dual loopback mode, the multiplexers are active and the functions of the circuit are divided into two with each receiver/
transmitter pair linked together to deconstruct and then reconstruct their respective signals. Differential Manchester data
enters the Differential Manchester receiver module and then is returned to the differential Manchester transmitter module.
Likewise, G.703 data enters the G.703 receiver module and is passed through to the G.703 transmitter module to be
returned as G.703 data. Because of the complete split in the communications path and because, in each case, the clocks
are extracted and reconstructed with the outgoing data, in this mode there must be two independent sources of timing.
One source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the
interface.
Figure 3-43: G.703 dual loopback mode
DMR = Differential Manchester Receiver

DMR G7X DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver
DMX G7R
842775A1.CDR

3.4.5 RS422 interface
3.4.5.1 Description
There are two RS422 inter-relay communications modules available: single-channel (module 7T) and dual-channel (module
7W). The modules can be configured to run at 64 kbps or 128 kbps. AWG 20 to 24 twisted shielded pair cable is
recommended for external connections. These modules are protected by optically-isolated surge suppression devices.
The shield pins (6a and 7b) are connected internally to the ground pin (8a). Proper shield termination is as follows:
• Site 1 — Terminate shield to pins 6a or 7b or both
• Site 2 — Terminate shield to COM pin 2b
Match the clock terminating impedance with the impedance of the line.
Figure 3-44: RS422 interface connections
3 Single-channel RS422 module Dual-channel RS422 module
7W
Tx – ~3b Tx – ~3b
7T
Rx – ~3a Rx – ~3a
RS422 communications
RS422 Tx + ~2a RS422 Tx + ~2a

channel 1 channel 1
Rx + ~4b Rx + ~4b
Shield ~6a Shield ~6a
+ ~7a Tx – ~5b
Clock
– ~8b Rx – ~5a
Common COM ~2b RS422 Tx + ~4a
channel 2
Surge ~8a Rx + ~6b
Shield ~7b
Tx – ~7a
Clock
Rx – ~8b
Common COM ~2b
~ indicates the slot position Surge ~8a
842776A3.CDR
The following figure shows the typical pin interconnection between two single-channel RS422 interfaces installed in slot W.
All pin interconnections are to be maintained for a connection to a multiplexer.
Figure 3-45: Typical pin interconnect between two RS422 interfaces
Tx – W3b W3b Tx –
7T
7T
Rx – W3a W3a Rx –
RS422 Tx + W2a W2a Tx + RS422

channel 1 channel 1
Rx + W4b W4b Rx +
Shield W6a W6a Shield
+ W7a W7a +
Clock Clock
– W8b W8b –
Common COM W2b W2b COM Common
Surge W8a W8a Surge
+ –
64 or 128 kbps 831728A5.CDR
3.4.5.2 Two-channel application via multiplexers

The RS422 interface can be used for single-channel or two-channel applications over SONET/SDH or multiplexed systems.
When used in single-channel applications, the RS422 interface links to higher-order systems in a typical way, observing
transmit (Tx), receive (Rx), and send timing (ST) connections. However, when used in two-channel applications, certain
criteria must be followed since there is one clock input for the two RS422 channels. The system functions correctly when
the following connections are observed and your data module has a terminal timing feature. Terminal timing is a common
feature in most synchronous data units that allows the module to accept timing from an external source. Using the
terminal timing feature, two-channel applications can be achieved if these connections are followed: the send timing

outputs from the multiplexer (data module 1) connects to the clock inputs of the UR RS422 interface in the usual way. In
addition, the send timing outputs of data module 1 are also paralleled to the terminal timing inputs of data module 2. By
using this configuration, the timing for both data modules and both UR RS422 channels is derived from a single clock
source. As a result, data sampling for both of the UR RS422 channels is synchronized via the send timing leads on data
module 1, shown as follows. If the terminal timing feature is not available or this type of connection is not wanted, the
G.703 interface is a viable option that does not impose timing restrictions.
Figure 3-46: Timing configuration for RS422 two-channel, three-terminal application
Data module 1
Signal name
Tx1(+) W2a SD(A) - Send data
7W
Tx1(–) W3b SD(B) - Send data

RS422
Rx1(+) W4b RD(A) - Received data
CHANNEL 1
Rx1(–) W3a RD(B) - Received data
Shield
+
W6a
W7a
RS(A) - Request to send (RTS)
RS(B) - Request to send (RTS)
3
CLOCK
– W8b RT(A) - Receive timing
RS422 COMMUNICATIONS
Tx2(+) W4a RT(B) - Receive timing

Tx2(–) W5b CS(A) - Clear To send
RS422
Rx2(+) W6b CS(B) - Clear To send
CHANNEL 2
Rx2(–) W5a Local loopback
Shield W7b Remote loopback
COMMON COM W2b Signal ground
SURGE W8a ST(A) - Send timing
ST(B) - Send timing
Data module 2
Signal name
TT(A) - Terminal timing
TT(B) - Terminal timing
SD(A) - Send data
SD(B) - Send data
RD(A) - Received data
RD(B) - Received data
RS(A) - Request to send (RTS)
RS(B) - Request to send (RTS)
CS(A) - Clear To send
CS(B) - Clear To send
Local loopback
Remote loopback
Signal ground
ST(A) - Send timing
ST(B) - Send timing
831022A3.CDR
Data module 1 provides timing to the B90 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides
timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been
omitted in the figure because they vary by manufacturer.
3.4.5.3 Transmit timing

The RS422 interface accepts one clock input for transmit timing. It is important that the rising edge of the 64 kHz transmit
timing clock of the multiplexer interface is sampling the data in the center of the transmit data window. Therefore, it is
important to confirm clock and data transitions to ensure proper system operation. For example, the following figure
shows the positive edge of the Tx clock in the center of the Tx data bit.

Figure 3-47: Clock and data transitions
Tx Clock
Tx Data
831733A1.CDR
3.4.5.4 Receive timing

The RS422 interface utilizes NRZI-MARK modulation code and therefore does not rely on an Rx clock to recapture data.
NRZI-MARK is an edge-type, invertible, self-clocking code.
To recover the Rx clock from the data-stream, an integrated digital phase lock loop (DPLL) circuit is utilized. The DPLL is
driven by an internal clock, which is 16-times over-sampled, and uses this clock along with the data-stream to generate a
data clock that can be used as the serial communication controller (SCC) receive clock.
3.4.6 RS422 and fiber interface

The following figure shows the combined RS422 plus fiberoptic interface configuration at 64 K baud. The 7L, 7M, 7N, 7P,
and 74 modules are used in two-terminal with a redundant channel or three-terminal configurations where channel 1 is
employed via the RS422 interface (possibly with a multiplexer) and channel 2 via direct fiber.
AWG 20 to 24 twisted shielded pair wiring is recommended for external RS422 connections. Ground the shield only at one
end. For the direct fiber channel, address power budget issues properly.
When using a laser interface, attenuators can be necessary to ensure that you do not exceed
Figure 3-48: RS422 and fiber interface connection
+ ~1a
7L, 7M, 7N,
7P, and 74
Clock
channel 1 – ~1b
Common COM ~2b
Tx – ~3b
Rx – ~3a
RS422 Tx + ~2a
channel 1
communications
Rx + ~4b
Shield ~6a
Fiber Tx2 Rx2
RS422
channel 2
Surge ~8a
842777A3.CDR
The connections shown in the figure are for multiplexers configured as data communications equipment (DCE) units.

3.4.7 G.703 and fiber interface

The following figure shows the combined G.703 plus fiber-optic interface configuration at 64 kbps. The 7E, 7F, 7G, 7Q, and
75 modules are used in configurations where channel 1 is employed via the G.703 interface (possibly with a multiplexer)
and channel 2 via direct fiber. AWG 24 twisted shielded pair wiring is recommended for external G.703 connections
connecting the shield to pin 1a at one end only. For the direct fiber channel, address power budget issues properly. See
previous sections for details on the G.703 and fiber interfaces.
When using a laser interface, attenuators can be necessary to ensure that you do not exceed the
Figure 3-49: G.703 and fiber interface connection
Shield ~1a
75, 7E, 7F, 7G,

and 7Q
3
Tx – ~1b
G.703 Rx – ~2a
channel 1
Tx + ~2b
communications
Rx + ~3a
Surge ~3b
Fiber Tx2
G.703
channel 2 Rx2
842778A2.CDR
3.4.8 IEEE C37.94 interface

IEEE C37.94 is a standard interface between teleprotection equipment and digital multiplexers.
The UR-series IEEE C37.94 modules (module types 2G, 2H, 2I, 2J, 76, and 77) are designed to interface with IEEE C37.94
compliant digital multiplexers or an IEEE C37.94 compliant interface converter for use with direct input and output
applications. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a multiplexer
and a teleprotection device. Data speed is typically 64 kbps, but the standard provides for speeds up to 64n kbps, where n
= 1, 2,…, 12. The UR-series C37.94 communication modules are either 64 kbps (with n fixed at 1) or 128 kbps (with n fixed at
2). The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from the standpoint
of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit rate of 2048
kbps.
The specifications for the module are as follows:
• IEEE standard — C37.94 for 1  128 kbps optical fiber interface (for 2G and 2H modules) or C37.94 for 2  64 kbps
optical fiber interface (for 76 and 77 modules)
• Fiber-optic cable type — 50 nm or 62.5 μm core diameter optical fiber
• Fiber-optic mode — multimode
• Fiber-optic cable length — up to 2 km
• Fiber-optic connector — type ST
• Wavelength — 820 ±40 nm
• Connection — as per all fiber-optic connections, a Tx-to-Rx connection is required
The UR-series C37.94 module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94
standard. The figure shows the concept.

Figure 3-50: IEEE C37.94 connection to compliant digital multiplexer

IEEE C37.94
fiber interface
Digital
UR-series multiplexer,
device IEEE C37.94
compliant
up to 2 km
842755A2.CDR
The UR-series C37.94 communication module can be connected to the electrical interface (G.703, RS422, or X.21) of a non-
compliant digital multiplexer via an optical-to-electrical interface converter that supports the IEEE C37.94 standard. The
following figure shows the concept.
3 Figure 3-51: IEEE C37.94 connection to non-compliant digital multiplexer
IEEE C37.94 RS422

fiber interface interface
Digital
UR-series IEEE C37.94 multiplexer
device converter with EIA-422
interface
up to 2 km
842756A2.CDR
In 2008, GE Grid Solutions released revised modules 76 and 77 for C37.94 communication to enable multi-ended fault
location functionality with firmware 5.60 release and higher. All modules 76 and 77 shipped since the change support this
feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60
and higher, the module can be identified with "Rev D" printed on it and is to be used on all ends of B90 communication for
two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For
customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed.
The UR-series C37.94 communication module has six switches to set the clock configuration. The following figure shows
the functions of these control switches.
Loop timing mode
842753A2.CDR
For the internal timing mode, the system clock is generated internally. Therefore, set the timing switch selection to internal
timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.
For the looped timing mode, the system clock is derived from the received line signal. Therefore, set the timing selection to
loop timing mode for connections to higher order systems.
The IEEE C37.94 communications module cover removal procedure is as follows:
1. With power to the relay off, remove the IEEE C37.94 module (type 2G, 2H, 2I, 2J, 76, or 77 module) as follows. Record
the original location of the module to help ensure that the same or replacement module is inserted into the correct
slot.
2. Simultaneously pull the ejector/inserter clips located at the top and bottom of each module in order to release the
module for removal.

5. Set the timing selection switches (channels 1 and 2) to the required timing modes (see description earlier).
7. Re-insert the IEEE C37.94 module. Take care to ensure that the correct module type is inserted into the correct slot
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged
position as the module is inserted smoothly into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is inserted fully.
Figure 3-53: IEEE C37.94 timing selection switch setting
Bottom cover
FRONT 3
Channel 1
Timing selection
switches
Top cover
Channel 2
Cover screw
REAR
831774A3.CDR
Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the
following figure.

Figure 3-54: Status LEDs
Tx1
CH1 Link/Activity LED
COMMS
Rx1
2B
C37.94SM
1300nm single-mode
ELED
2 channel
Tx1
Tx2
REV. D CH2 Link/Activity LED
Technical support:
3
Tel: (905)294-6222
Fax: (905)201-2098
Rx2
(NORTH AMERICA)
1 800 547-8629
GE Multilin
Made in Canada Tx2
CH1 Clock Configuration LED

FRONT VIEW REAR VIEW 842837A1.cdr
The clock configuration LED status is as follows:

• Flashing green — loop timing mode while receiving a valid data packet
• Flashing yellow — internal mode while receiving a valid data packet
• Solid red — (switch to) internal timing mode while not receiving a valid data packet
The link/activity LED status is as follows:
• Flashing green — FPGA is receiving a valid data packet
• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"
• Solid red — FPGA is not receiving a valid packet or the packet received is invalid
3.4.9 C37.94SM interface

The UR-series C37.94SM communication modules (2A and 2B) are designed to interface with modified IEEE C37.94
compliant digital multiplexers or IEEE C37.94 compliant interface converters that have been converted from 820 nm multi-
mode fiber optics to 1300 nm ELED single-mode fiber optics. The IEEE C37.94 standard defines a point-to-point optical link
for synchronous data between a multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard
provides for speeds up to 64n kbps, where n = 1, 2,…, 12. The UR-series C37.94SM communication module is 64 kbps only
with n fixed at 1. The frame is a valid ITU-recommended G.704 pattern from the standpoint of framing and data rate. The
frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit rate of 2048 kbps.
The specifications for the module are as follows:
• Emulated IEEE standard — Emulates C37.94 for 1  64 kbps optical fiber interface (modules set to n = 1 or 64 kbps)
• Fiber-optic cable type — 9/125 m core diameter optical fiber
• Fiber-optic mode — Single-mode, ELED compatible with HP HFBR-1315T transmitter and HP HFBR-2316T receiver
• Fiber-optic cable length — Up to 11.4 km
• Fiber-optic connector — Type ST
• Wavelength — 1300 ±40 nm
• Connection — As per all fiber-optic connections, a Tx-to-Rx connection is required

The UR-series C37.94SM communication module can be connected directly to any compliant digital multiplexer that
supports C37.94SM, as shown.
C37.94SM
fiber interface
Digital
UR-series
multiplexer
device
C97.94SM
up to 10 km
842757A2.CDR
It also can be connected directly to any other UR-series relay with a C37.94SM module, as shown.
C37.94SM
fiber interface 3
UR-series UR-series
device with device with
C37.94SM C37.94SM
module module
up to 10 km
842758A2.CDR
In 2008, GE Grid Solutions released revised modules 2A and 2B for C37.94SM communication to enable multi-ended fault
location functionality with firmware 5.60 release and higher. All modules 2A and 2B shipped since the change support this
feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60
and higher, the module can be identified with "Rev D" printed on it and is to be used on all ends of B90 communication for
two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For
customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed.
The UR-series C37.94SM module has six switches that are used to set the clock configuration. The following figure shows
the functions of these control switches.
Loop timing mode

842753A2.CDR
For the internal timing mode, the system clock is generated internally. Therefore, set the timing switch selection to internal
timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.
For the looped timing mode, the system clock is derived from the received line signal. Therefore, set the timing selection to
loop timing mode for connections to higher-order systems.
The C37.94SM communications module cover removal procedure is as follows:
1. With power to the relay off, remove the C37.94SM module (module 2A or 2B) as follows. Record the original location of
the module to help ensure that the same or replacement module is inserted into the correct slot.
2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release
the module for removal.
5. Set the timing selection switches (channels 1 and 2) to the required timing modes (see description earlier).


7. Re-insert the C37.94SM module. Take care to ensure that the correct module type is inserted into the correct slot
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged
position as the module is inserted smoothly into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is inserted fully.
Figure 3-56: C37.94SM timing selection switch setting
Bottom cover
FRONT
3 Channel 1
Timing selection
switches
Top cover
Channel 2
Cover screw
REAR
831774A3.CDR
Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the
following figure.

CHAPTER 3: INSTALLATION ACTIVATE RELAY
Figure 3-57: Status LEDs
Tx1
CH1 Link/Activity LED
COMMS
Rx1
2B
C37.94SM
1300nm single-mode
ELED
2 channel
Tx1
Tx2
REV. D CH2 Link/Activity LED
Technical support:
Tel: (905)294-6222
Fax: (905)201-2098
(NORTH AMERICA)
1 800 547-8629
Rx2
3
GE Multilin
Made in Canada Tx2

FRONT VIEW REAR VIEW 842837A1.cdr
The clock configuration LED status is as follows:

• Flashing green — loop timing mode while receiving a valid data packet
• Flashing yellow — internal mode while receiving a valid data packet
• Solid red — (switch to) internal timing mode while not receiving a valid data packet
The link/activity LED status is as follows:
• Flashing green — FPGA is receiving a valid data packet
• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"
• Solid red — FPGA is not receiving a valid packet or the packet received is invalid
3.5 Activate relay

The relay is in the default “Not Programmed” state when it leaves the factory. When powered up successfully, looking at
the front panel, the "Trouble" LED is on and the "In Service" LED is off. The relay in the “Not Programmed” state blocks
signaling of any output relay. These conditions remain until the relay is explicitly put into “Programmed” state.
RELAY SETTINGS: When the relay is powered up, the "Trouble LED" is on, the "In Service" LED is off, and this message
Not Programmed displays, indicating that the relay is in the "Not Programmed" state and is safeguarding (output
relays blocked) against the installation of a relay whose settings have not been entered. This
message remains until the relay is explicitly put into "Programmed" state.
The relay can be activated on the front panel or in the EnerVista software.
To activate the relay using the front panel:
1. Press the MENU key until the SETTINGS header flashes momentarily and the PRODUCT SETUP message displays.
2. Press the MESSAGE right arrow until the SECURITY message displays.
3. Press the MESSAGE down arrow until the INSTALLATION message displays.
4. Press the MESSAGE right arrow until the RELAY SETTINGS: Not Programmed message displays.

INSTALL SOFTWARE CHAPTER 3: INSTALLATION
SETTINGS

 SETTINGS  SECURITY
 PRODUCT SETUP  
 DISPLAY
  PROPERTIES

 INSTALLATION RELAY SETTINGS:
   Not Programmed
3 5. After the RELAY SETTINGS: Not Programmed message displays, press a VALUE key to change the selection to
"Programmed."
6. Press the ENTER key to save the change.
RELAY SETTINGS: RELAY SETTINGS: NEW SETTING

Not Programmed Programmed HAS BEEN STORED
7. When the "NEW SETTING HAS BEEN STORED" message appears, the relay is in "Programmed" state and the "In Service"
LED turns on.
To activate the relay using EnerVista software:
1. Navigate to Settings > Product Setup > Installation and change the Relay Settings field to "Programmed."
2. Save the change.
3.6 Install software

3.6.1 EnerVista communication overview
The EnerVista UR Setup software communicates to the relay via the front panel RS232 or USB port or the rear RS485 /
Ethernet ports.
To communicate via the RS232 port, use a standard straight-through serial cable. Connect the DB-9 male end to the relay
and the DB-9 or DB-25 female end to the computer COM2 port as described in the CPU Communication Ports section
earlier in this chapter.

CHAPTER 3: INSTALLATION INSTALL SOFTWARE
Figure 3-58: Relay communication options
Regional
control
center
Ethernet Remote
10/100 Mbps communications link
Local
control
UR-series IED
EnerVista Engineer
GE Multilin F485
communications converter
Modem
3
RS485 115 kbps
RS232
EnerVista
Reports
EnerVista
Troubleshooting
Commissioning
Setting changes
842759A2.CDR
To communicate through the B90 rear RS485 port from a computer RS232 port, the GE Grid Solutions RS232/RS485
converter box is required. This device (catalog number F485) connects to the computer using a straight-through serial
cable. A shielded twisted-pair wire (20, 22, or 24 AWG) connects the F485 converter to the B90 rear communications port.
The converter terminals (+, –, GND) are connected to the B90 communication module (+, –, COM) terminals. See the CPU
Communication Ports section in chapter 3 for details. The line is terminated with an R-C network (that is, 120 , 1 nF) as
described in this chapter.
3.6.2 System requirements

The relay front panel or the EnerVista UR Setup software can be used to communicate with the relay. The software
interface is the preferred method to edit settings and view actual values because the computer monitor can display more
information.
The system requirements for the EnerVista software are as follows:
• Intel Pentium processor (dual core) or (recommended) Core Duo
• Microsoft Windows 7 with Service Pack 1 (32-bit or 64-bit), Windows 10, Windows Server 2008 Release 2 with Service
Pack 1 (64-bit), or Windows Server 2012 Release 2 (64-bit), in the required EnerVista language, such as French or
Japanese
• 1 GB free hard drive space
• 2 GB RAM
• 1280 x 800 display screen

INSTALL SOFTWARE CHAPTER 3: INSTALLATION
3.6.3 Install software

After ensuring that the requirements for using EnerVista UR Setup software are met, there are three ways to install the
software:
• From the DVD
• Download EnerVista Launchpad software from http://www.gegridsolutions.com/multilin and install it
• Download the EnerVista UR Setup software from http://www.gegridsolutions.com/multilin and install it
Install on a computer that has an operating system in the required language, for example a German operating system for
use with EnerVista software in German.
The front panel can be switched in the EnerVista software between enhanced and basic panels under
Maintenance > Change Front Panel.
3 To install the software from the DVD and using EnerVista Launchpad:
1. Insert the DVD into the DVD drive of your computer.
2. Click the Install Now button and follow the instructions.
3. When installation is complete, start the EnerVista Launchpad application.
4. Click the IED Setup section of the Launch Pad window.
Figure 3-59: Adding a UR device in Launchpad window
5. In the EnerVista Launch Pad window, click the Add Product button and select the appropriate product as follows.
Select the Web option to ensure the most recent software release, or select CD if you do not have an Internet
connection, then click the Add Now button to list software items for the product. EnerVista Launchpad obtains the
software from the Internet or DVD and automatically starts the installation program after prompting about updates.
From the web, the software is downloaded. A wizard opens.

CHAPTER 3: INSTALLATION ADD DEVICE TO SOFTWARE
Figure 3-60: Identifying the UR device type
6. In the wizard, click the Next button and complete the process. The files are installed in the directory indicated, and the
installation program automatically creates icons and adds an entry to the Windows start menu.
The UR device is added to the EnerVista Launchpad window, as shown.
Figure 3-61: UR device added to Launchpad window
7. For other than English, configure the language for the front panel in the EnerVista software under Settings > Product
Setup > Display Properties. User-entered strings are not translated, for example relay names, so setting the language
now ensures that the names are entered/displayed in the required language. For the EnerVista software language,
access the View > Language menu item.
3.7 Add device to software

You connect remotely to the B90 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup
software. The B90 also can be accessed locally with a computer through the front panel RS232 or USB port or the rear
Ethernet port using the Quick Connect feature.
The following procedures are outlined:
• Add device for serial access; see the Configure Serial Connection section
• Add device for the rear Ethernet port; see the Configure Ethernet Connection section
• Add device for access using a modem; see the Configure Modem Connection section

ADD DEVICE TO SOFTWARE CHAPTER 3: INSTALLATION
• Connect locally with a computer through either the front RS232 or USB port or rear Ethernet port; see the Connect to
the B90 section
• Discover automatically UR devices within a network; see the Automatic Discovery of UR Devices section
Devices in the Device Setup window are listed in the order entered.
Devices in the main software window are listed alphabetically. Use the Device Name to order them as required, for
example B30 Odessa, B30 Truro, B90, T35.
You cannot import a file to add a device to the software. You can import settings as outlined at the end of the chapter.
The Quick Connect button also can be used to add devices. The device is added to a Quick Connect menu item in the
Online Window area, cannot be moved from it to another grouping, and needs to be renamed in the Device Setup window.
GE instead recommends using the Device Setup window to add devices, as outlined here.
3.7.1 Set IP address in UR

3
Implement IP addresses for the computer and a B90 device as follows.
The UR family supports the use of subnetworks as documented in RFC 950, which divides class-based networks into
subnetworks (non-CIDR). The classes and IP address ranges are defined as follows.
Table 3-7: IP address classes
Classes IP address range Default subnet mask address UR devices
A 1.0.0.0 to 127.255.255.255 255.0.0.0 65,535 or more
B 128.0.0.0 to 191.255.255.255 255.255.0.0 255 to 65,534
C 192.0.0.0 to 223.255.255.255 255.255.255.0 0 to 254
D 224.0.0.0 to 239.255.255.255 (Reserved for multicasting)
E 240.0.0.0 to 255.255.255.255 (Reserved)
Both network and subnet addresses are contained within a range. The number of hosts determines the class and
addresses as follows:
• Class A 255.0.0.0 — The first octet (255) specifies the network, the second to fourth octets (0) specify the subnet and
host. Use this class when you have more than 65,535 hosts (UR devices).
• Class B 255.255.0.0 — The first two octets (255) specify the network, the third octet (0) specifies the subnet, and the
fourth octet (0) specifies the host. Use this class when you have 255 to 65,534 hosts (UR devices).
• Class C 255.255.255.0 — The first three octets (255) specify the network and the last octet (0) specifies the subnet and
host. Use this class when you have up to 254 hosts (UR devices).
An example of implementation is one computer and one UR device. Because there is one UR device, class C addressing is
required. So we use UR 192.167.2.x with subnet mask 255.255.255.0 and computer 192.167.3.x with subnet mask
255.255.255.0.
For older, non-CIDR routing protocols, such as RIP version 1, follow these restrictions:
• Identical subnet masks — Use a single mask for all subnets within a network
• Contiguous subnets — The subnets must be contiguous and not split among networks. The subnets cannot pass
traffic through other networks.
The IP and subnet addresses need to be added to the UR for Ethernet communication.
For serial communication, for example using any front RS232 port and the Quick Connect feature, the addresses are not
required, but typically they are entered to add/configure devices for regular use.
To add the IP addresses:
1. On the front of the UR, press the MENU key until the SETTINGS menu displays.
2. Navigate to SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK  PRT IP ADDRESS SETTING.
3. Enter an IP address, for example 10.11.33.1, and press the ENTER key to save the value. For example, press the period
key to clear any existing address, then press the number keys to add anew address.

4. In the same menu, select the PRT SUBNET IP MASK setting. Enter a subnet IP address, for example 255.0.0.0.
5. Press the ENTER key to save the value.
The gateway address also needs to be configured when connecting through an Ethernet network. Access SETTINGS 
PRODUCT SETUP  COMMUNICATIONS  IPv4 ROUTE TABLE  DEFAULT IPv4 ROUTE  GATEWAY ADDRESS.
If using a blue or grey Ethernet cable, skip the rest of the this section. If using an orange cross-over Ethernet cable, the
computer needs to be set up as follows.
1. Use an orange Ethernet cross-over cable to connect the computer to the rear Ethernet port. In case you need it, the
following figure shows the pinout for an Ethernet cross-over cable.
Figure 3-62: Ethernet cross-over cable PIN layout
3 4 5 6
END 1 END 2
2 7 Pin Wire color Diagram Pin Wire color Diagram
1 8
3
1 White/orange 1 White/green
2 Orange 2 Green
3 White/green 3 White/orange
4 Blue 4 Blue
5 White/blue 5 White/blue
6 Green 6 Orange
7 White/brown 7 White/brown
8 Brown 8 Brown
842799A1.CDR
Next, assign the computer an IP address compatible with the relay’s IP address.
1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network
connections window. Or in Windows 7, access the Network and Sharing Center in the Control Panel.

2. Right-click the Local Area Connection icon and select Properties.
3. Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button.
4. Click the “Use the following IP address” box.

5. Enter an IP address with the first three numbers the same as the IP address of the B90 relay and the last number
different (in this example, 1.1.1.2).
6. Enter a subnet mask equal to the one set in the B90 (in this example, 255.0.0.0).
7. Click the OK button to save the values.

Before continuing, test the Ethernet connection.

1. Open a Windows console window, for example by selecting Start > Run from the Windows Start menu and typing
“cmd” or clicking the Start button and entering "cmd".
2. Type the following command, substituting the IP address of 1.1.1.1 with yours:
C:\WINNT>ping 1.1.1.1
3. If the connection is successful, the system returns four replies similar to the following:
Pinging 1.1.1.1 with 32 bytes of data:
Reply from 1.1.1.1: bytes=32 time<10ms TTL=255
Ping statistics for 1.1.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip time in milliseconds:
Minimum = 0ms, Maximum = 0ms, Average = 0 ms 3
4. Note that the values for time and TTL vary depending on local network configuration.
5. If the following sequence of messages appears when entering the C:\WINNT>ping 1.1.1.1 command:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Minimum = 0ms, Maximum = 0ms, Average = 0 ms
verify the physical connection between the B90 and the computer, and double-check the programmed IP address in
the PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.
Hardware error.
Hardware error.
Hardware error.
Hardware error.
verify the physical connection between the B90 and the computer, and double-check the programmed IP address in
the PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.
Destination host unreachable.
verify the IP address is programmed in the local computer by entering the ipconfig command in the command
window.
C:\WINNT>ipconfig
Windows IP Configuration

Ethernet adapter <F4FE223E-5EB6-4BFB-9E34-1BD7BE7F59FF>:

Connection-specific DNS suffix. . :
IP Address. . . . . . . . . . . . : 0.0.0.0
Subnet Mask . . . . . . . . . . . : 0.0.0.0
Default Gateway . . . . . . . . . :
Ethernet adapter Local Area Connection:
Connection-specific DNS suffix . :
IP Address. . . . . . . . . . . . : 1.1.1.2
Subnet Mask . . . . . . . . . . . : 255.0.0.0
Default Gateway . . . . . . . . . :
C:\WINNT>
Before using the Quick Connect feature through the Ethernet port, disable any configured proxy settings in Internet
Explorer.
3 1. Start the Internet Explorer software.

2. Select the Tools > Internet Options menu item and click the Connections tab.
3. Click on the LAN Settings button to open the following window.
4. Ensure that the “Use a proxy server for your LAN” box is not checked.
If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been
disconnected from the B90 relay.
1. Start the Internet Explorer software.
2. Select the UR device from the EnerVista Launchpad to start EnerVista UR Setup.

3. Click the Quick Connect button to open the window.
4. Select the Ethernet interface and enter the IP address assigned to the B90, then click the Connect button. The 3
EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick
Connect” and displays them on the left side of the screen.
5. Expand the sections to view data directly from the B90 device.
Each time that the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct
communications to the B90. This ensures that configuration of the EnerVista UR Setup software matches the B90 model
number.
When direct communications with the B90 via Ethernet is complete, make the following changes:
1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network
connections window.
2. Right-click the Local Area Connection icon and select the Properties item.
3. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button.
4. Set the computer to “Obtain a relay address automatically” as shown.

If the computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been
disconnected from the B90 relay.
3.7.2 Configure serial connection

Two options are possible: local connection between computer and front RS232 port, and remote connection using the rear
RS485 terminals.
To use the RS485 terminals at the back of the relay, a GE Grid Solutions F485 converter (or compatible RS232-to-RS485
converter) is required. See the F485 instruction manual for details.
1. Connect the computer to the F485 and the F485 to the RS485 terminal on the back of the UR device. Or connect the
computer to the RS232 port on the front of the relay.
2. Start the EnerVista UR Setup software, or in EnerVista Launchpad select the UR device to start the software.
3 3.
4.
Click the Device Setup button. The window opens.
Click the Add Site button. A new category is added. Enter a site name in the Site Name field. Optionally add a short
Description of the site. This example uses “Location 1” as the site name.
5. Click the Add Device button. A new device is added.
6. Enter a name in the Device Name field, up to 15 characters, and optionally add a Description of the site. The Color is
for the text in the device list in the Online Window.
7. Select “Serial” from the Interface drop-down list. Interface parameters display that must be entered for serial
communications. Try to load automatically the fields by clicking the Read Order Code button.
Figure 3-63: Configuring serial communication
8. Enter the COM port used by the computer, the baud rate, and parity settings from the front panel SETTINGS  PRODUCT
SETUP  COMMUNICATIONS  SERIAL PORTS menu, and the relay slave address setting from the front panel SETTINGS
 PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL  MODBUS SLAVE ADDRESS menu in their respective

fields.
Baud Rate — Typically 19200 bits per second (bps) for RS232, and higher for RS485. Both modems need to use the
same rate, meaning at the computer and the B90 ends.
Parity — Set to None if unsure
Bits — Set to 8 if unsure
Stop Bits — Set to 1 if unsure
Post Terminal Window — Enable this option if you have a Schweitzer Engineering (SEL) SEL-203x Communications
Processor, such as an SEL-2030 or SEL-2032. This option enables display of a terminal window to allow interaction
with the other device.
9. Click the Read Order Code button to connect to the B90 and upload the order code to the EnerVista software. If a
communications error occurs, ensure that the EnerVista software serial communications values entered in the
previous step correspond to the relay setting values, and also ensure that the same IP address is not assigned to
multiple B90 ports.
10. Click the OK button when the relay order code has been received. The new site and device are added to the Online
3
Window.
The device has been configured for serial communications. Proceed to the Connect to the B90 section to begin
communication.
3.7.3 Configure Ethernet connection

You connect the Ethernet cable, define a site in the software, then add the relay as a device for the site.
The Ethernet cable can be connected from the relay to an Ethernet network or directly to the computer. The computer and
UR device must be on the same subnet.
1. Connect the Ethernet network cable and any SFP supplied with the B90 to the Ethernet port on the back of the device.
3. Click the Device Setup button. The window opens.
4. Click the Add Site button. A new category is added. Enter a site name in the Site Name field. Optionally add a short
Description of the site. This example uses “Location 1” as the site name.
7. Select “Ethernet” from the Interface drop-down list. This displays a number of interface parameters that must be
entered for Ethernet functionality.

Figure 3-64: Configuring Ethernet communication
8. Enter the relay IP Address, which can be viewed on the device front panel under SETTINGS  PRODUCT SETUP 
COMMUNICATIONS  NETWORK  IP ADDRESS. Once the IP address is entered, try to load automatically the fields by
clicking the Read Order Code button.
9. Enter the relay Slave address and Modbus Port address values from the settings in the front panel SETTINGS 
PRODUCT SETUP  COMMUNICATIONS MODBUS PROTOCOL menu.
10. If using a gateway to connect to the device, select Yes from the drop-down list.
11. Click the Read Order Code button to connect to the B90 device and upload the order code. If the device was entered
already, a message displays "Device ’x’ is also using IP address...." If a communications error occurs, ensure that the
values entered in the previous steps correspond to the relay setting values, and also ensure that the same IP address
is not assigned to multiple B90 ports.
12. Click the OK button when the relay order code has been received. The new site and device are added to the Online
Window.
The device has been configured for Ethernet communications. Proceed to the Connect to the B90 section to begin
communications.
3.7.4 Configure modem connection

A modem connection allows a computer to communicate with a UR device over phone lines.
Two modems are required. One modem is connected to the UR device, either by connecting the serial cable to the front
panel port or through a RS485 box to the rear terminals of the UR device. The second modem is connected to the
computer that initiates the connection.
To add a UR device for modem connections:
1. Connect the modems to the computer and UR.

3. Click the Device Setup button. The window opens.
4. Click the Add Site button. A new category is added. Enter a site name in the Site Name field, such as London East.
Optionally add a short Description of the site, such as the address or intersection.
7. Select “Modem” from the Interface drop-down list. This displays a number of interface parameters that must be
entered.
8. Select "Generic Modem" from the Modem Name drop-down list, then enter the Phone Number to dial to establish
communication with the remote modem.
Post Terminal Window — Enable this option if you have a SEL-203x Communications Processor, such as an SEL-2030
or SEL-2032. It enables display of a terminal window to allow interaction with the other device. 3
9. Once the phone number is entered, try to load automatically the device information by clicking the Read Order Code
button.
10. Click the OK button when the relay order code has been received. The new device is added to the Online window.
The UR device has been added to the software.
3.7.5 Automatic discovery of UR devices

The EnerVista UR Setup software can find and communicate to all UR-family devices located on an Ethernet network.
Using the Discover button in the Device Setup window, a single click of the mouse triggers the software to detect any URs
located on the network. This is done by searching a range of IP addresses based on the subnet mask of the computer.
When a UR device is detected, the EnerVista UR Setup software proceeds to configure all settings and order code options
in the window. This feature allows the user to identify and interrogate all UR devices at a location.
Examples of address ranges are as follows:
• If the host has an IP address of 3.94.247.10 and its subnet mask is 255.255.252.0, then the host’s subnet is 3.94.244.0,
and the possible IP addresses in this subnet are
3.94.244.1 to 254
3.94.245.1 to 254
3.94.246.1 to 254
3.94.247.1 to 254
The discover function scans all those possible IP addresses to detect UR relays.
• If the host has an IP address of 3.94.247.145 and its subnet mask is 255.255.255.128, then the host’s subnet is
3.94.247.128, and the discover function scans IP addresses of 3.94.247.128 to 3.94.248.254 for UR relays
To automatically add UR devices:
1. In the EnerVista software, click the Device Setup button. The window opens.
2. Click the Discover button. The software searches for UR devices on the computer subnet and adds any found to the
Online Window area. If a required device is not found, add it manually as outlined earlier.

CONNECT TO THE B90 CHAPTER 3: INSTALLATION
Figure 3-65: Discover button to detect UR devices in network
3 3.8 Connect to the B90

There are four ways to the connect to the device, as follows:
• RS232 or USB port (outlined here)
• RS485 port
• Ethernet port (outlined here)
• LAN
When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the
device.
When unable to connect, ensure that the same IP address is not assigned to multiple B90 ports, for example under
Settings > Product Setup > Communications > Network.
If still unable to connect, try unplugging and replugging the Ethernet connection. If that does not work, try to ping the
device from the computer, and if unsuccessful, restart the computer.
When multiple computers are connected to a B90 device, EnerVista settings windows are not updated
automatically. They are refreshed when re-opened. If a user changes a setting on one computer, the other users
need to refresh the display by closing and opening the settings window to see the change. To ensure that current
settings are always viewed, close settings windows when not in use so that they are up-to-date when next
accessed.
3.8.1 Connect to the B90 in EnerVista

For information on using the EnerVista software, see the Interfaces chapter.
To access the relay in EnerVista:
1. Open the Settings > Product Setup > Display Properties window as shown. The window opens with a status indicator
on the lower left of the EnerVista UR Setup window.

CHAPTER 3: INSTALLATION CONNECT TO THE B90
Figure 3-66: EnerVista window
Quick action hot links
3
Expand the site list by double-clicking
or selecting the +/– box.
Communications status indicators:

Green = OK
Red = No communications
UR icon = report is open
842743A3.CDR
2. If the status indicator is red, verify that the Ethernet network cable is properly connected to the Ethernet port on the
back of the relay and that the relay has been properly set up for communication.
3. If a relay icon appears in place of the status indicator, then a report (such as an oscillography or event record) is open.
Close the report to re-display the green status indicator.
4. The Display Properties settings can now be viewed, edited, or printed.
3.8.1.1 Quick action hot links

The EnerVista UR Setup software has several quick action buttons to provide instant access to several functions that are
performed often when using URs. From the online window, users can select the relay to interrogate from a pull-down
window, then click the button for the action to perform. The following quick action functions are available:
• View the event record
• View the last recorded oscillography record
• View the B90 protection summary
• View all of the B90 metering values
• View the status of all B90 inputs and outputs
• Generate a service report
3.8.2 Use Quick Connect via front RS232 port

This feature applies to the enhanced and basic front panels.
To connect to the UR from a computer using a serial cable:
1. Connect an RS232 serial cable to the computer and the front panel RS232 port. For example, use a USB-to-serial
RS232 DB9M converter cable when connecting to the USB port on the computer.
3. Click the Quick Connect button. The window opens.

CONNECT TO THE B90 CHAPTER 3: INSTALLATION
Figure 3-67: Quick Connect window to access a device
3 4. Select the serial Interface and the communications port (COM Port) from the drop-down lists, then click Connect. The
COM Port is that of the computer.
5. The EnerVista software creates a site named “Quick Connect” with a corresponding device also named “Quick
Connect” and displays them in the Online Window. Expand the sections to view data directly from the UR device. Use
the Device Setup button to change the site name.
number.
3.8.3 Use Quick Connect via front USB port

This feature applies to the graphical front panel.
To connect to the UR from a computer using a USB cable:
1. Connect the cable to the computer and the front panel USB port (square connector).
3. Click the Quick Connect button to open the window.
4. Select the USB Interface and the "GE Virtual Serial Port" driver from the drop-down list, then click Connect. If the GE
driver does not display, it means that the USB cable was connected on Windows 10 when upgrading the UR software.
You need to re-install the EnerVista software with the USB cable disconnected.
5. The EnerVista software creates a site named “Quick Connect” with a corresponding device also named “Quick
Connect” and displays them in the Online Window. Expand the sections to view data directly from the UR device. Use
the Device Setup button to change the site name.
number.
3.8.4 Use Quick Connect via a rear Ethernet port

To connect to a UR using an Ethernet cable:
1. In the EnerVista software, click the Quick Connect button. The window opens.

CHAPTER 3: INSTALLATION SET UP CYBERSENTRY AND CHANGE DEFAULT PASSWORD
Figure 3-68: Quick Connect window for Ethernet connection
2. Select the Ethernet interface and enter the IP address assigned to the B90, then click the Connect button. The 3
EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named "Quick
Connect" and displays them in the Online Window.
3. Expand the sections to view data directly from the B90 device. Use the Device Setup button to change the site name.
Each time that the EnerVista software is initialized, click the Quick Connect button to establish direct communications to
the B90. This ensures that configuration of the EnerVista UR Setup software matches the B90 model number.
3.9 Set up CyberSentry and change default password

If and when first using CyberSentry security, use the following procedure for set up.
1. Log in to the relay as Administrator by using the VALUE keys on the front panel or through EnerVista connected serially
(so that no IP address is required). If logging in through EnerVista choose Device authentication (see figure). Enter the
default password "ChangeMe1#". Note that the "Lock relay" setting needs to be disabled in the Security > Supervisory
menu. When this setting is disabled, configuration and firmware upgrade are possible. By default, this setting is
disabled.
2. Enable the Supervisor role if you have a need for it.
3. Make any required changes in configuration, such as setting a valid IP address for communication over Ethernet.
4. Log out of the Administrator account by choosing None.
Next, device or server authentication can be chosen on the login screen, but the choice is available only in EnerVista. Use
Device authentication to log in using the five pre-configured roles (Administrator, Supervisor, Engineer, Operator, Observer,
or Administrator and Supervisor when Device authentication is disabled). When using a serial connection, only Device
authentication is supported. When Server authentication is required, characteristics for communication with a RADIUS
server must be configured on the UR. This is possible only through the EnerVista software. The RADIUS server itself also
must be configured. At the end of this instruction manual, the appendix called RADIUS Server Configuration gives an
example of how to set up a simple RADIUS server. Once both the RADIUS server and the parameters for connecting the UR
to the server have been configured, you can choose Server authentication on the login screen of EnerVista.

IMPORT SETTINGS CHAPTER 3: INSTALLATION
Figure 3-69: Login screen for CyberSentry
3
During the commissioning phase, you have the option to bypass the use of passwords. Do so by enabling the Bypass
Access setting under Settings > Product Setup > Security > Supervisory. Be sure to disable this bypass setting after
commissioning the device.
You can change the password for any role either from the front panel or through EnerVista. If using EnerVista, navigate to
Settings > Product Setup > Security. Change the Local Administrator Password, for example. It is strongly recommended
that the password for the Administrator be changed from the default. Changing the passwords for the other three roles is
optional.
3.10 Import settings

The following file types can be imported:
• URS — UR settings file (firmware version7.3x or earlier)
• IID — Instantiated IED capability description file — Actual settings on UR
• CID — Configured IED description file — Settings sent to the UR (may or may not be actual settings). When using IEC
61850, network settings can also be configured by accepting a CID file that includes them, as long as the IP address of
at least one port is manually configured in the relay before the CID file is sent and the IP address matches that in the
file.
The import is done in the Offline Window area.
To import a settings file:
1. In the Offline Window area, right-click the device and select the Add Device from File option. The device is that from
which you want to import settings.
2. If required, change the Files of type drop-down list.
3. Select the file to import.
To apply the settings to a live device:
1. Drag-and-drop the device entry from the Offline Window area to its entry in the Online Window area.
Individual settings also can be dragged and dropped between Online and Offline Window areas.
The order codes much match.
This is what happens:

• CID — For version 7.30 or later, a new URS file generates and moves into a new device folder, generating SCL files from
the new URS file. Files in the folder have new time stamps. The CID file retains its time stamp.
• URS — When not IEC 61850 and version is lower than 7.30, the file is added and time stamp is unchanged. When
clicking in the software on the tree element, a device folder is created, the original file moves into it, and time stamp is
on the URS file is retained.

CHAPTER 3: INSTALLATION CONNECT TO D400 GATEWAY
When EIC 61850 and version is 7.30 or later, the file is added and time stamp is unchanged. When clicking in the
software on the tree element, a device folder is created, the original file moves into it, SCL files are generated there,
and the "Last modified" time stamp on the URS file changes.
3.11 Connect to D400 gateway

A GE Multilin D400 Substation Gateway can be used to collect data from UR devices in a local area network (LAN). It collects
metering, status, event, and fault report data from serial or LAN-based intelligent substation devices, and it pre-processes
the data. The D400 supports up to 16 serial and eight network connections, with multiple devices possible on each serial
connection. Up to 10 concurrent file transfer sessions are possible, meaning data for up to 10 URs can be transferred at
the same time and any additional IEDs are queued on a first-come-first-served basis. The D400 can then upload files to a
demilitarized zone (DMZ) server at the enterprise level.
Setup is as follows. For UR devices with the CyberSentry software option, when there is a need to retrieve periodically the 3
logs from the UR securely without a human interface, the following approach can be used. See the D400 manual for
configuration details to achieve it.
A UR in the substation can authenticate a user either connecting to a RADIUS server or on the device itself. This depends
on the user name used for authentication on a connection. The D400 connects to the UR device using an Ethernet, USB, or
serial port on the UR. The Ethernet connection can be ST or RJ-45 type. The serial connection can be RS232 or RS485. At
the other end, a cable attaches to the rear of D400. Use the D400 software to configure a serial or network
communication/connection for the UR, then to configure the IED device blocks/clients for the UR, and then to configure
record retrieval. Once configured, the UR and D400 use a keyfile authentication mechanism to establish communication.
For UR devices with the IEC 61850 software option, also use the D400 IEC 61850 Loader software.
When a D400 detects new files available for download from a UR, it connects to the UR and reads the files via sFTP
protocol. The following files can be transferred:
• Oscillography files
• Event records
• Log files
• Configuration (setting) files
The D400 information is viewable in its software and in a web browser.
3.11.1 Oscillography files

These are stored in COMTRADE format in the D400 folder system using the UR site and device name.
3.11.2 Event records

These are stored as the EVT.TXT file in the D400 folder system using the UR site and device name.
3.11.3 Log files

Log files can be retrieved for UR 7.0 and later. The following file types are possible, stored in the D400 folder system using
the UR site and device name:
• factory_event.txt — Information about change methods and origins. Saved with a "_YYMMDDhhmmss" retrieval time
stamp, for example FACTORY_EVENT_170525183124.TXT.
• setting_changes.log — Information on what settings have been changed. Saved with a "_YYMMDDhhmmss" retrieval
time stamp, for example SETTING_CHANGES_170525183124.TXT.

CONNECT TO D400 GATEWAY CHAPTER 3: INSTALLATION
3.11.4 Setting files

These are the configuration/settings files in the IEC 61850 SCL/IID format. The ur.iid file is saved with a
"_YYMMDDhhmmss" retrieval time stamp, for example ur_170525183124.iid. It is stored in the D400 folder system using
the UR site and device name.

Chapter 4: Interfaces
Interfaces
This chapter explains the EnerVista software interface, the front panel interface, logic diagrams, and Engineer interface for
logic design and monitoring.
4.1 EnerVista software interface

4.1.1 Introduction
The EnerVista UR Setup software provides a single facility to configure, monitor, maintain, and troubleshoot relays
connected over local or wide-area networks. It can be used while disconnected (offline) or connected (online) to a UR
device. In offline mode, settings files can be created for eventual downloading to the device. In online mode,
communication with the device is real-time.
The EnerVista UR Setup software is provided with every B90. This chapter outlines the EnerVista software interface. The
EnerVista UR Setup help file in the software also provides details for getting started and using the software interface.
4.1.2 Settings files

The EnerVista software supports the following three ways of handling changes to relay settings:
• In offline mode (relay disconnected) to create or edit relay settings files for later transfer to relays
• While connected to a relay to modify relay settings, and then save the settings to the relay
• Create/edit settings files and then write them to the relay while connected to the relay
See the back up section in the Maintenance chapter for instructions on how to create a settings file either offline or online.
Settings files are organized on the basis of file names assigned by the user. A settings file contains data pertaining to the
following types of relay settings:
• Device definition
• Product setup
• System setup
• FlexLogic
• Grouped elements
• Control elements
• Inputs/outputs

ENERVISTA SOFTWARE INTERFACE CHAPTER 4: INTERFACES
• Remote resources
• Testing
Factory default values are supplied and can be restored after any changes.
The following communications settings are not transferred to the B90 with settings files:
Modbus Slave Address
Modbus TCP Port Number
RS485 COM2 Baud Rate
RS485 COM2 Parity
COM2 Minimum Response Time
COM2 Selection
RRTD Slave Address
RRTD Baud Rate
IP Address (see end of previous chapter for information)
IP Subnet Mask
IP Routing
When a settings file is loaded to a B90 that is in-service, the following sequence occurs:
4 1. The B90 takes itself out of service.
2. The B90 issues a UNIT NOT PROGRAMMED major self-test error.
3. The B90 closes the critical fail contact.
The Maintenance chapter outlines how to use a settings file in the .urs format for backup and restore.
4.1.3 Event viewing

In online or offline mode, you can view and analyze data generated by triggered parameters as follows:
• Event recorder — The event recorder captures contextual data associated with the last 1024 events, listed
chronologically from most recent to oldest
• Oscillography — The oscillography waveform traces and digital states are used to provide a visual display of power
system and relay operation data captured during specific triggered events
Event records are viewable at software and device-specific levels. Access the former under Admin > Event Log > View.
Access the latter under Actual Values > Records > Event Record.
Event record entries for CyberSentry are explained in the next chapter. The following table outlines some software-level
entries.
Table 4-1: Event record descriptions
Event Description
EnerVista UR Setup SESSION STARTED The EnerVista software was launched
Language was changed. The user changed the software language using the View > Language menu item
DEFAULT USERS CREATED The user management window was launched using the Admin > User Management menu
item
: Successful upload of firmware The firmware on a device was upgraded
END
Firmware verified
Firmware uploaded
Firmware erased
START: Upload new firmware
EnerVista UR Setup EVENT LOG CLEARED The event record was cleared. All event records were deleted using the Admin > Event Log >
Clear menu item.

CHAPTER 4: INTERFACES ENERVISTA SOFTWARE INTERFACE
4.1.4 File support

The following support applies, where the Settings List is at the bottom left and the Site List is at the top left of the EnerVista
window:
• Execution — Any EnerVista UR Setup file that is opened launches the application or provides focus to the already
opened application. If the file was a settings file (has a .urs extension) that had been removed from the Settings List
navigation menu, it is added back to the menu.
• Drag and Drop — The device settings and individual settings can be dragged and dropped between the Online and
Offline Window areas. Also, any Windows Explorer directory folder is a file drag source and drop target.
New files that are dropped into the Offline Window are added to the tree, which is automatically sorted alphabetically
with respect to settings file names. In the Online Window, files or individual menu items that are dropped in the
selected device menu are sent automatically to the online device.
4.1.5 EnerVista main window

The EnerVista UR Setup software window has the following components:
1. Title bar that shows the pathname of the active data view or the name of the software
2. Main window menu bar
3. Main window toolbar 4
4. Site list / online window area
5. Settings list / offline window area
6. Software windows, with common toolbar
7. Settings file data view windows, with common toolbar
8. Workspace area with data view tabs
9. Status bar
10. Quick action hot links

Figure 4-1: EnerVista UR Setup software window
2 1 6 7
10
4
4 5
9 8 842786A2.CDR
4.1.6 Protection summary window

The Protection Summary is a graphical user interface to manage elements, such as enabling and disabling them. Access it
under Settings > Protection Summary. See the Settings chapter for information on use.

Figure 4-2: Protection Summary interface (B30 example shown)
4.1.7 Settings templates

Settings file templates simplify the configuration and commissioning of multiple relays that protect similar assets. An
example is a substation that has 10 similar feeders protected by 10 UR F60 relays.
In these situations, typically 90% or greater of the settings are identical among devices. The templates allow engineers to
configure and test these common settings, then lock them so that they are not available to users. For example, locked
settings can be hidden from view for field engineers, allowing them to quickly identify and concentrate on specific settings.
The remaining settings (typically 10% or less) can be specified as editable and made available to field engineers installing
the devices. These are settings such as protection element pickup values and CT and VT ratios.
The settings template mode allows the user to define which settings are visible in the software. Settings templates can be
applied to both settings files (settings file templates) and online devices (online settings templates). The functionality is
identical for both purposes.
Template mode is available in the English software only.
Settings file conversion from previous firmware versions is supported.
4.1.7.1 Enable the settings template

The settings file template feature is disabled by default. It can be enabled in offline or online mode.
The procedure outlines how to enable in offline mode the settings template for UR settings files.
1. Locate the settings file in the Offline Window area of the EnerVista UR Setup software. If not there, a file can be added
from an online device by right-clicking it and selecting the Add Device to Offline Window option.
2. In the Offline Window area, right-click the selected device or settings file and select the Template Mode > Create
Template option.
The settings file template is now enabled and the file menus display in light blue. The settings file is now in template
editing mode. To undo the action, select Template Mode > Remove Template.

Alternatively, the settings template can be applied to online settings, as follows.

1. Locate the device in the Online Window area of the EnerVista UR Setup software.
2. Right-click the device and select the Template Mode > Create Template option. The software prompts for a template
password. This password is required to use the template feature and must be at least four characters in length.
Figure 4-3: Entering a settings file password
3. Enter and re-enter the new password, then click OK to continue.

The online settings template is now enabled. The device is now in template editing mode.
4 4.1.7.2 Edit the settings template

The settings template editing feature allows the user to specify which settings are available for viewing and modification in
EnerVista UR Setup. By default, all settings except the FlexLogic equation editor settings are locked.
1. With the template already enabled, locate the device or settings file in the Online or Offline Window area in the
software.
2. Right-click the device or file and select the Template Mode > Edit Template option to verify or place the device in
template editing mode (check mark beside option). If prompted, enter the template password then click OK.
3. Open the relevant settings window that contains settings to be specified as viewable.
By default, all settings are specified as locked and displayed against a grey background. The icon on the upper right of
the settings window indicates that the EnerVista software is in EDIT mode. The following example shows the phase
time overcurrent settings window in edit mode.
Figure 4-4: Settings template with all settings specified as locked
4. Specify the settings to make viewable by clicking them.

A setting available to view displays with a yellow background.

Figure 4-5: Settings template with two settings specified as editable
5. Click the Save button to save changes to the settings template.

6. Continue through any other settings window to specify all viewable settings.
The next time that the device/settings are accessed, only those specified as viewable/editable display in the menu
hierarchy.
4
4.1.7.3 Add password protection to a template
GE recommends that templates be saved with password protection to maximize security.
When templates are created for online settings, the password is added during the initial template creation step. It
does not need to be added after the template is created.
To add password protection to a settings file template:

1. In the Offline Window area, right-click the device and select the Template Mode > Password Protect Template
option.
The software prompts for a template password. This password must be at least four characters in length.
2. Enter and re-enter the new password, then click OK to continue.

The settings file template is now secured with password protection.
4.1.7.4 View the settings template

Once all necessary settings are specified for viewing, users are able to view the settings template on the online device or
settings file. There are two ways to specify the settings view with the settings template feature:
• Display only those settings available for editing
• Display all settings, with settings not available for editing greyed-out
To display only the settings available for editing:
1. Right-click the device in the Online or Offline Window area and apply the template by selecting the Template Mode >

View In Template Mode option.

2. Enter the template password if prompted, then click OK to apply the template.
Once the template has been applied, users are limited to view and edit the settings specified by the template. The effect of
applying the template to the phase time overcurrent settings is shown.
Figure 4-6: Applying templates using the View in Template Mode command
4
Phase time overcurrent window with template applied via
the Template Mode > View In Template Mode command.
The template specifies that only the Pickup and Curve
Phase time overcurrent settings window without template applied.
settings be available.
842858A1.CDR
Viewing the settings in template mode also modifies the settings menu, showing only the settings categories that contain
editable settings. The effect of applying the template to a typical settings menu is shown as follows.
Figure 4-7: Applying templates using the View in Template Mode settings command
Use the following procedure to display settings available for editing and settings locked by the template.
1. Right-click the device in the Online or Offline Window area and apply the template by selecting the Template Mode >
View All Settings option.
2. Enter the template password then click OK to apply the template.
Once the template has been applied, users are limited to edit the settings specified by the template, but all settings are
shown. The effect of applying the template to the phase time overcurrent settings is shown as follows.

Figure 4-8: Applying templates using the View All Settings command
Phase time overcurrent settings window without template applied. Phase time overcurrent window with template applied via
the Template Mode > View All Settings command.
The template specifies that only the Pickup and Curve
settings be available.
4
842859A1.CDR
4.1.7.5 Remove the settings template

Once a settings template is removed, it cannot be reapplied and a new settings template needs to be defined before use.
1. Right-click the device in the Online or Offline Window area and select the Template Mode > Remove Template option.
2. Enter the template password if prompted and click OK to continue.
3. Confirm that you want to remove the template by clicking Yes.
The EnerVista software removes all template information and all settings are available.
4.1.8 Secure and lock FlexLogic equations

The UR allows users to secure some or all FlexLogic equations, preventing unauthorized viewing or modification of critical
FlexLogic applications. This is accomplished using the settings template feature to lock individual entries within FlexLogic
equations.
Secured FlexLogic equations remain secure when files are sent to and retrieved from any UR-series device.
Locking can be tied to the serial number too.
4.1.8.1 Lock FlexLogic equations

To lock individual entries of a FlexLogic equation:
1. Right-click the settings file or online device and select the Template Mode > Create Template item to enable the
settings template feature.
2. If prompted, enter the template password.
3. Select the FlexLogic > FlexLogic Equation Editor settings menu item.
By default, all FlexLogic entries are specified as viewable and display against a yellow background. The icon on the
upper right of the window also indicates that EnerVista UR Setup is in EDIT mode.
4. Specify the entries to lock by clicking them.
The locked entries display a grey background as shown in the example.

Figure 4-9: Locking FlexLogic equation entries in Edit Mode
4 5. Click the Save button to save and apply changes to the settings template.
6. Select the Template Mode > View In Template Mode option to view the template.
7. Optionally apply a password to the template by right-clicking the device and selecting the Template Mode >
Password Protect Template option.
Once the template has been applied, users are limited to view and edit the FlexLogic entries not locked by the template.
The effect of applying the template to the FlexLogic entries is shown here.
Figure 4-10: Locking FlexLogic entries through settings templates
Typical FlexLogic™ entries without template applied. Typical FlexLogic™ entries locked with template via
the Template Mode > View In Template Mode command.
842861A1.CDR
The FlexLogic entries are also shown as locked in the graphical view and on the front panel display.

Figure 4-11: Secured FlexLogic in graphical view
4.1.8.2 Lock FlexLogic equations to the serial number

A settings file and associated FlexLogic equations also can be locked to a UR serial number. Once FlexLogic entries in a
settings file have been secured, use the following procedure to lock the settings file to a serial number. A serial number is
viewable under Actual Values > Product Info > Model Information, the inside front panel, and the rear of the device.
1. Right-click the setting file in the Offline Window area and select the Edit Device Properties item. The window opens.

Figure 4-12: Settings file properties window
2. Enter the serial number of the B90 device to lock to the settings file in the Serial # Lock field.
3. Click the OK button to apply the change. The serial number is not validated.
The settings file and corresponding secure FlexLogic equations are now locked to the B90 device specified by the serial
number.
4.1.9 Settings file traceability

A traceability feature for settings files allows the user to quickly determine if the settings in a B90 device have been
changed since the time of installation from a settings file. When a settings file is transferred to a B90 device, the date, time,
and serial number of the B90 are sent back to EnerVista UR Setup and added to the settings file on the local computer. This
information can be compared with the B90 actual values at any later date to determine if security has been compromised.
The traceability information is only included in the settings file if a complete settings file is either transferred to the B90
device or obtained from the B90 device. Any partial settings transfers by way of drag and drop do not add the traceability
information to the settings file.

Figure 4-13: Settings file traceability
1 SETTING FILE TRANSFERRED

TO UR-SERIES DEVICE
The serial number and last setting change date

are stored in the UR-series device.
The serial number of the UR-series device and the file transfer
date are added to the setting file when setting files
are transferred to the device.
Compare transfer dates in the setting file and the

UR-series device to determine if security SERIAL NUMBER AND TRANSFER DATE 4
has been compromised. 2 SENT BACK TO ENERVISTA AND
ADDED TO SETTING FILE. 842864A2.CDR
With respect to the figure, the traceability feature is used as follows.

• The transfer date of a settings file written to a B90 is logged in the relay and can be viewed in the EnerVista software
or the front panel display. Likewise, the transfer date of a settings file saved to a local computer is logged in the
EnerVista software.
• Comparing the dates stored in the relay and on the settings file at any time in the future indicates if any changes have
been made to the relay configuration since the settings file was saved.
4.1.9.1 Settings file traceability information

The serial number and file transfer date are saved in the settings files when they are sent to a B90 device.
The B90 serial number and file transfer date are included in the settings file device definition within the EnerVista UR Setup
offline window as shown in the example.
Figure 4-14: Device definition showing traceability data
Traceability data in settings

file device definition
842863A1.CDR
This information is also available in printed settings file reports as shown in the example. A report is generated by right-
clicking and selecting the Print Settings option.

Figure 4-15: Settings file report showing traceability data
Traceability data
in settings report
4
842862A1.CDR
4.1.9.2 Online device traceability information

The B90 serial number and file transfer date are available for an online device through the actual values. Select the Actual
Values > Product Info > Model Information menu item within the EnerVista online window as shown in the example.
Figure 4-16: Traceability data in Actual Values window
This information is also available from the front panel display through the following actual values:
ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION  SERIAL NUMBER
ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION  LAST SETTING CHANGE
4.1.9.3 Additional traceability rules

The following additional rules apply for the traceability feature:
• If the user changes any settings within the settings file in the offline window, then the traceability information is
removed from the settings file
• If the user creates a new settings file, then no traceability information is included in the settings file
• If the user converts an existing settings file to another revision, then any existing traceability information is removed
from the settings file
• If the user duplicates an existing settings file, then any traceability information is transferred to the duplicate settings
file

CHAPTER 4: INTERFACES FRONT PANEL INTERFACE
4.2 Front panel interface

This section explains use of the enhanced, basic, and graphical front panels.
4.2.1 Front panel
4.2.1.1 Enhanced front panel

The enhanced front panel consists of LED panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional
user-programmable pushbuttons.
The front panel is hinged to allow access to removable modules inside the chassis. The B90 enhanced front panel can be
horizontal. The following figure shows the horizontal front panel.
Figure 4-17: Enhanced horizontal front panel
Five column LED indicator panel
Display
4
Keypad
Control
pushbuttons (3)
Front panel
RS232 port
User-programmable pushbuttons 1 to 16 842810A2.CDR
4.2.1.2 Basic front panel

The basic front panel consists of LED panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional user-
programmable pushbuttons.
The front panel is hinged to allow easy access to removable modules inside the chassis. There is also a removable dust
cover that is to be removed when accessing the keypad. The B90 basic front panel can be horizontal. The following figure
shows the horizontal front panel.

FRONT PANEL INTERFACE CHAPTER 4: INTERFACES
Figure 4-18: Basic horizontal front panel

LED panel 1 LED panel 2 LED panel 3
Display
Front panel
RS232 port
Small user-programmable
User-programmable Keypad
(control) pushbuttons 1 to 7
pushbuttons 1 to 12
827801A9.CDR
4 4.2.1.3 Graphical front panel

The graphical front panel consists of a USB port, LED panel, color screen display, user-programmable pushbuttons, and
navigation keys. The screen is used to read data, such as metering actual values, alarms, self-test messages, and event
records, and for viewing single-line diagrams. Settings can be changed on the front panel, except for the graphical front
panel itself and for IEC 61850. The USB port connects to a computer with the EnerVista software and can be used to
upgrade the relay and to transfer files and settings. The USB port is the square type B.
User-programmable pushbuttons 9 to 16 can be programmed among the 10 pushbuttons on the left and right sides of the
display.
Figure 4-19: Graphical front panel
Side pushbuttons
LEDs Display User-programmable pushbuttons
1 5
IN SERVICE
TROUBLE
TEST MODE
TRIP
ALARM 2 6
PICKUP
VOLTAGE
CURRENT 3 7
USB port FREQUENCY
OTHER
PHASE A 4 8
PHASE B
Not used
PHASE C
NEUTRAL / GND
RESET ESC
ENTER
Reset Tab pushbuttons Home Escape Navigation keys

859760A1.CDR

4.2.2 Front panel display
4.2.2.1 Enhanced and basic front panels

Messages display on a backlit liquid crystal display (LCD) to make them visible under poor lighting conditions. When the
keypad and display are not actively being used, the display defaults to user-defined messages. Any high-priority event-
driven message overrides the default messages.
Up to 20 characters can be used to configure some setting names in the software, while up to 12 characters display on the
front panel. A tilde ~ symbol is used for the twelfth character on the front panel when a name extends beyond the 12
character limit. An example is shown for a Virtual Input.
Figure 4-20: Tilde symbols displays with names 12 or more characters long
4
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the
front panel or the LEDs.
To view the front panel in EnerVista software:
1. Click Actual Values > Front Panel, then any option.
Figure 4-21: Front panel use in the software (C60 shown)
4.2.2.2 Graphical front panel

The graphical front panel has a seven-inch (17.8 cm) color liquid crystal display (LCD). The display provides convenient
access to operational data generated by the relay, enables local control of power system devices, and allows display/
editing of settings.

Header content varies by page. The home page displays any active icons, such as security status, active setting group, and
active target messages. It shows the date and time of the relay. If the relay synchronizes to an external time source via PTP,
IRIG-B, SNTP, and so on, the date/time is shown in white, and otherwise in yellow. On pages other than the home page, the
header displays the name of the page.
The footer dynamically labels the Tab, or control, pushbuttons immediately below.
Page content displays between the header and footer.
Figure 4-22: Home page example with default content (product information)
Setting Group
Alarm Target Relay Date and Time
859850A1.cdr
There are multiple ways to navigate pages, by using the pushbuttons and the menu hierarchy. The menu hierarchy is
similar to the other front panels whereby you select a submenu using Up and Down arrow pushbuttons, and press the
ENTER or Right pushbutton. On setting pages, opening a setting for editing is done by highlighting the setting using Up and
Down pushbuttons, and pressing the ENTER or Right pushbutton.
Home page
Press the Home pushbutton to display the root page no matter the state. Any edit, control, or password entry sessions are
cancelled. The header shows several relay/system status icons. The default content of the home page is the product
information page and can be user-configured to show the content of any single-line diagram page, annunciator page,
metering page, or event records page for example. The Tab pushbuttons on the bottom row each navigate to their page.
The home page displays for a user-configured time period, then scrolls through user-configured pages, a feature referred
to as rolling.
Holding the Home pushbutton for one second displays the product information page. The Home page also can display
when settings are saved.
Security indicator, showing how many people are logged in, including local and remote users. The lock is red when
one or more users are logged in and other otherwise green.
When no users are logged in because login is not required, an icon does not display.
Identifies the active setting group number (not shown)

Displays when an abnormal annunciator alarm is present. Navigate to the Annunciator for details. When there
are no such alarms, the icon does not display.
Even when you acknowledge/reset an alarm, the icon displays as long as the condition remains. For example, a
breaker trouble alarm displays, you acknowledge it, but the icon remains because the breaker trouble remains.
Active targets symbol, where targets are error messages.
View error messages by pressing the Menu Tab pushbutton, then accessing the TARGETS menu. Pressing the
RESET button clears those messages that can be.
Configure the home page in the software under Settings > Product Setup > Graphical Panel > Home Page. The menu
does not display when there is no graphical front panel.
Rolling mode
After a user-defined period of inactivity, the graphical front display rolls among up to 10 user-selected pages. The roll-to-
pages are selected in the EnerVista software, with the defaults being the product information page. Each page displays for
less than five seconds. Also, the display backlight intensity is lowered after a configurable period to a user-defined level (0,
10, 20, or 30%); lower intensity extends the life of the display.
Configure rolling mode in the software under Settings > Product Setup > Graphical Panel > Rolling Mode.
Operation works as follows:
• Press the Home pushbutton or ESCAPE pushbutton twice to cancel rolling, restore full backlight intensity, and return
to the Home page 4
• Press the ENTER, ESCAPE, or a pushbutton to pause rolling once and restore full backlight intensity
Rolling is disabled by setting the delay to 0.
The following buttons display at the top of the window:
• Save — Updates the connected device if online or the open setting file if offline with changes made
• Restore — Undoes changes that have not been saved
• Default — Changes all rolling mode settings to their factory default values
• Reset — Displays factory default values. Previous changes are not lost unless you save the reset window.
Single-line diagrams
A single-line diagram, or mimic diagram, is a line drawing of elements in an electrical system. The graphical front panel
displays up to five single-line diagrams. Each can be configured to show the arrangement of a portion of the power
system, the status of circuit breakers and of ground and disconnect switches, user-programmable pushbuttons, and
metering and status values. Each also enables control of the displayed power system devices.
Configure the diagrams under Settings > Product Setup > Graphical Panel > Single Line Diagram Editor.
Each single-line diagram page has a user-configurable name that appears in the header and in the footer Tab pushbutton
label. Factory default names are SLD 1 to SLD 5. Pages that have no configured content have a blank Tab pushbutton
label, and the Tab pushbutton does nothing. The label for the current page has a blue background.

Figure 4-23: Toolbar options for single-line diagram
Select Breaker IEEE Transformer 3W IEEE

Line Breaker IEC Transformer 2W IEEE
Line Crossover Breaker GE Transformer 3W IEC
Bus Crossover Switch IEEE Transformer 2W IEC

Bus Switch IEC Reactor IEEE
Feeder Switch GE Reactor IEC
Ground
Metering Capacitor General IEC
Generator Status Capacitor Polarity IEEE
Motor Text Current Transformer IEEE
AC Source
Pushbutton Current Transformer IEC
Voltage Transformer IEEE

4 Voltage Transformer IEC
859875A1.cdr
The letters T, S, B, R, and X next to a controllable element have the following meaning. An example (TSB) is shown in the
next figure.
• T — The element is "tagged." Local and remote control of the device are inhibited, both open and close. Tripping is
unaffected unless additional logic has been configured.
• S — The position indication of the device is substituted with a manually entered value
• B — Blocking open/close command is bypassed
• R — Autoreclose is enabled and not blocked
• X — The device is out-of-service and control is not available
Single-line diagram example

The following example outlines how to create a circuit breaker diagram, then how to close the second circuit breaker. The
figure shows six switches (SW, M), two breakers (CB), feeder (arrow), and ground (lined arrow).

Figure 4-24: Single-line diagram of open circuit breakers
Under Settings > System Setup > Switches and Breakers, enable and name the six switches and two breakers. Switch 6,
M568G, has the A/3 Pole Opened setting on.
Figure 4-25: Configure Breaker and Switch settings
In the EnerVista software, open the single-line diagram editor under Settings > Product Setup > Graphical Panel > Single
Line Diagram Editor.
Add the four switches for the top line by clicking the GE switch symbol in the toolbar, then clicking in the window. (If the UR
device is not online, the software attempts to connect.) Right-click to edit properties. Rotate switches SW569 and SW5682
to 270 degrees. Rotate switches 5681 and SW523 to 90 degrees. Ignore the TSB text.

Add the two lower switches. Leave rotation at 0 degrees.

Add the two breakers by clicking the GE breaker symbol in the toolbar, then click in the window. Right-click to edit
properties, rotating 90 degrees and setting the color to red (open).
Draw lines to fill in the gaps between the switches and breakers by clicking the line symbol in the toolbar, then clicking and
dragging on the canvas to draw a line. Do not draw a single line for the top line, but instead draw several small lines.
Add the feeder arrow head by clicking the symbol in the toolbar, then clicking the end of the line.
Add the ground symbol by clicking the symbol in the toolbar, then clicking the end of the line.
Add three metered values by clicking the M symbol in the toolbar, then clicking near the feeder arrow. Double-click to edit.
The three metered values are SRC1 Vag Mag, SRC 1 P, and SRC 1 Q.
Name the page by right-clicking the bottom tab. Here, page 1 is renamed "Milton line M568M."
Note that active symbols in the toolbar display and those that are inactive are greyed-out.
The diagram has been created. Save it by clicking the Save button.
Next is to close circuit breaker CB523. This circuit breaker is shown at the top right of the figure. A vertical line means that
it is open, and the color can be set as red or green.
On the graphical front panel, press the Home pushbutton, then press the SLDs pushbutton to activate the first single-line
4 diagram page.
Figure 4-26: Single-line diagram on graphical front panel
Press the Enable Control pushbutton. The side pushbutton labels display.

Figure 4-27: Side pushbutton display on graphical front panel
Press the CB523 breaker pushbutton. Its menu displays.

Figure 4-28: Pushbuttons to control the breaker 4
Press the pushbutton to close the breaker, confirming the action at the prompt.
In this diagram, the two circuit breakers have hard-coded actions available to them. No action is possible on the switches.
Note the USER PB 9 and 10 entries in the earlier figure. As outlined later, these are activated by clicking the PB icon on the
software toolbar. These two pushbuttons can be configured under Settings > Product Setup > User-Programmable
Pushbuttons.
Single-line diagram editor use

Start the application in the EnerVista software under Settings > Product Setup > Graphical Panel > Single Line Diagram
Editor.
• Load — Opens single-line diagram files, which replaces one or all five windows with that in the file selected

• Store — Saves all five single-line diagrams as a .mif file. Because single-line diagrams are not retained when using the
Convert Device Settings function, for example when converting in the Offline Window area from version 7.6 to 7.7, GE
recommends making backup files using this function.
On the right side of the window is a toolbox containing the components that can be added to the window. These include
line, breaker, disconnect, metering value, status value, text, and miscellaneous power system elements. To create the
single-line diagram, click the symbol, then click in the window. Once in the window, the component can be positioned and
its properties modified. When using the pointing device to position a component, the component can snap to the nearest
snap point. Snap points are in a 4 x 4 rectangular grid. The keyboard arrow keys move the selected component(s) in one
pixel increments when snap locations are inadequate. Multiple components can be selected and moved or deleted as a
group, or copied and pasted to another location. Right- or double-clicking a component opens the properties window.
Ctrl+A selects all objects in a diagram.
Lines
Line components represent power system buses or electrical connections between power system elements. They can also
be used as visual dividers and underline.
To add a line component, click it in the toolbox, then click in the window. Double-click a line to open its properties window
to set orientation.
Figure 4-29: Line and bus crossover symbols
4
Static symbols
Static symbols depicting power system elements are available. For information, see the ANSI/IEEE 315A and IEC 60617
standards.
Up to 32 static symbols can be used per single-line diagram.
To add a symbol, click it in the toolbox, then click in the window. Double-click the symbol to open its properties window to
set orientation.

Figure 4-30: IEEE and IEC static symbols
Breaker and disconnect components

Breaker components and disconnect components are interfaces to the UR breaker control elements and disconnect
switch elements. On a UR device they show dynamically the breaker or disconnect status as calculated by the element,
and provide means to open, close, tag, bypass interlock, and substitute (force status of) the element. Breaker components
in addition provide means to enable/disable breaker autoreclose.
Each breaker and disconnect component can be configured to use UR-style symbols, IEC symbols, or simple square/slash
symbols as shown in the following figure. The symbols assume horizontal symbol orientation, red - closed color, and green
- open scheme. With vertical orientation, they are rotated 90 degrees.

Figure 4-31: Single-line diagram symbols
To add a breaker or disconnect component, click it in the toolbox, then click in the window. Up to 10 dynamic components
can be added to each single-line diagram.
Breaker and disconnect components have three different parts: label, symbol, and flags. Drag each of its parts to their final
locations. Double or right-click any of these parts to open the properties window. Properties that can be edited are label
text, breaker control element or disconnect switch element number, symbol orientation (horizontal or vertical), color
scheme (red - closed, or red - open), and assigned side button (if any). If the selected breaker or disconnect element does

not exist in the target relay or has not been enabled, then the component is displayed in the graphical front panel and in
the drawing edit window in grey. The color scheme selection has no effect when an IEC style symbol is used because IEC
style symbols do not use color.
Symbol orientation
The figure shows the orientation available for the breaker and disconnect switch (taking Open status as examples). The
default position is 0 degrees.
Figure 4-32: Single-line diagram symbol orientation
A question mark displays in a symbol on the graphical front panel when status is bad. The question mark does not rotate
with orientation.
Figure 4-33: Symbols when status is bad
The following figures show the orientation available for the static components. The default position is 0 degrees.

Figure 4-34: Single-line diagram static symbol orientation (sheet 1 of 2)

Figure 4-35: Single-line diagram static symbol orientation (sheet 2 of 2)
User-programmable pushbuttons
User-programmable pushbuttons 1 to 8 are physical pushbuttons on the right side of the graphical front panel, numbering
down the two columns.
User-programmable pushbuttons 9 to 16 can be programmed among the 10 pushbuttons on the left and right sides of the
screen display. They show dynamically and provide a means to perform the same control as the other pushbuttons.

Figure 4-36: Assigning pushbuttons 9 to 16 to the display
4 As an example, if you set up a single-line diagram with two breakers and six switches, then eight of the side pushbuttons
are used automatically for control of the breakers and switches. Side pushbuttons 9 and 10 are available. In the single-line
diagram, let us set side pushbutton 9 to clear event records as follows:
• Show side pushbutton 9 on the graphical front panel — Click the PB symbol in the toolbar, then set Side button 9 to
pushbutton 9 in the drop-down list. This pushbutton then displays when appropriate on the right side of the screen
display.
• Program event record clearing — Set Settings > Product Setup > Clear Relay Records > Clear Event Records to
FlexLogic operand PUSHBUTTON 9 ON
• Program pushbutton 9 — Set Settings > Product Setup > User-Programmable Pushbuttons > Pushbutton 9
Function to "Self-reset." When pressed, pushbutton 9 clears the event records.
To instead set the second user pushbutton (not a side pushbutton) to clear events, follow the second and third bullet
points, selecting settings of PUSHBUTTON 2 ON and Pushbutton 2.
Metering components
Metering components show dynamically the value of a FlexAnalog operand or actual value. Up to 16 metering
components can be added to each single-line diagram.
To add a metering component, click the M symbol in the toolbox, then click in the window. Drag it to its final location.
Double-click it to open the properties window. The figure shows the properties that can be edited.

Figure 4-37: Metering properties
Status components
Status components show dynamically the value of a FlexLogic operand. Up to 16 can be used in a diagram and 30 in all
single-line diagrams.
An example is to show the Off or On state of the ANY MAJOR ERROR FlexLogic operand. The name of the operand displays in
the single-line diagram editor, then as Off or On on the graphical front panel.
To add a status component, click the S symbol in the toolbox, then click in the window. Drag it to its final location. Double-
click it to open the properties window. Properties that can be edited include parameter (any FlexLogic operand), text color
background color, and on and off text.
Optionally add a text label to display beside the status.
Text
Text components show a single line of user-configured text.
Up to 16 text components can be used per single-line diagram.
To add a text component, click the T symbol in the toolbox, then click in the window. Drag it to its final location. Double-
click it to open the properties window. Properties that can be edited are text, color, and size.
Annunciator
An annunciator is a grid of small windows for alarms, actual values, self-test messages, and product information.
The graphical front panel emulates a conventional annunciator panel. The annunciator has 96 windows, each with a
description of the alarm condition that lights the window. The windows are arranged in rows and columns of 3 x 4, 4 x 6, or
6 x 8 over several pages. Each window can have up to three lines of configurable text, and one line can instead be a
metered value. Normally the window background is dark, and when the configured FlexLogic operand becomes On, the
window lights up.
The figure shows that two alarms are active. One alarm is configured red and the other alarm is configured blue. The red
alarm type is Self Reset, so the alarm displays in a solid color. The blue alarm type is Acknowledgeable, so the alarm flashes
until it is acknowledged, for example by navigating with the arrow keys and pressing the ENTER button. The alarm then
remains blue until the trigger condition is eliminated.

Figure 4-38: 3x4 annunciator page with two active windows
To display the annunciator, press the Home pushbutton, then the Annunciator Tab pushbutton. If there is one or more
4 window in alarm or requiring reset, the annunciator page showing the first of these opens. Otherwise the first annunciator
page opens.
Alarms do not display automatically. Set the Home page and/or rolling pages to display annunciator pages.
The Tab pushbutton labels populate with the annunciator pages. The label text for each annunciator page is configurable
and displays in the header and Tab label. The current page has a blue Tab label. Tab labels for annunciator pages that
have an active window (that is, on, latched, or unacknowledged) are red. Pages where alarms are not triggered have a grey
Tab label. Pages that have no configured windows do not have Tab pushbuttons and do not display.
The Up, Down, Left, and Right pushbuttons cause the selection to move one window in the indicated direction. Pressing the
Right pushbutton past the last window in a row scrolls the display to any next annunciator page, not the next row. The
behavior is similar for the other pushbuttons, for example pressing the Up pushbutton while in the top row goes to any
previous page. If no previous page exists, no action occurs.
Annunciator windows are positioned statically, so that all windows are visible no matter their state.
Alarm types of each window can be configured as Self Reset, Latched, or Acknowledgeable. In Self Reset mode, the
window lighting follows the state of the configured FlexLogic operand. The self-reset mode alarm sequence conforms to
ISA-18.1-1979 (R2004) standard type A 4 5 6.
Figure 4-39: Annunciator alarm sequence in Self Reset mode
Process: Normal
Sequence: Normal
Visual: Off
Return to Normal
To Abnormal
Process: Abnormal
Sequence: Acknowledged
Visual: On
859856A1.vsd

Latched mode is intended for transient signals such as trip, and it conforms to ISA-18.1-1979 (R2004) standard type M 6.
Figure 4-40: Annunciator alarm sequence in Latched mode
Process: Normal
Sequence: Normal To Abnormal
Visual: Off
Return to Normal Reset while

Process: Abnormal or Normal
Sequence: Alarm
Normal
Visual: Fast Flash
Process: Abnormal
Reset while
Sequence: Acknowledged
Abnormal
Visual: On
859857A1.vsd
4
In Acknowledgeable mode, both Off to On and On to Off state changes in the configured operand cause the background to
flash; the window must be acknowledged/reset to cancel flashing. This mode conforms to ISA-18.1-1979 (R2004) standard
type R-6.
Figure 4-41: Annunciator alarm sequence in Acknowledgeable mode
Process: Normal
Reset Sequence: Normal To Abnormal
Visual: Off
Process: Normal Reset while Normal Process: Abnormal or Normal

Sequence: Ringback Sequence: Alarm
Visual: Slow Flash Return to Abnormal Visual: Fast Flash
Process: Abnormal
Reset while
Return to Normal Sequence: Acknowledged
Abnormal
Visual: On
859858A1.vsd
To reset all annunciator windows:

1. In the software, access Actual Values > Graphical Panel > Annunciator Panel.
To acknowledge/reset all annunciator windows on a page:

1. On the graphical front panel with none of the annunciator windows selected, press the RESET pushbutton once for
acknowledgement and twice for reset. The flashing stops.
To acknowledge an annunciator window:

1. On the graphical front panel, press the Up, Down, Left, and Right pushbuttons to select the window, so that is has a
yellow outline. Press the RESET or ENTER pushbutton. While a window is selected, if that window has activated since
the last restart, the date/time of the last activation of that window displays in the header.

An alarm remains in an alarm state (for example, displays red) when the condition remains. That is, if you acknowledged a
flashing alarm but the alarm condition remains, the background color remains red.
The SETTINGS > INPUTS/OUTPUTS > RESETTING > RESET ANNUNCIATOR setting can be used to select a FlexLogic
operand that when activated acknowledges/resets all annunciator windows.
Annunciator editor
The annunciator editor is used to configure alarms and actual value displays for the graphical front panel.
The path in the EnerVista software is Settings > Product Setup > Graphical Panel > Annunciator Editor.
The figure shows the annunciator editor and its preview window. The page name is entered as General at the top right.
Acknowledgeable and self-resetting alarms are set for basic functions, such as online/offline, Ethernet ports, unauthorized
access/failed logins, and battery failure. The text to display in the annunciator window is entered. The IN SERVICE LED is set
to be green because when the device is on, this LED is green. The preview shows what the annunciator looks like with all
alarms triggered. The last window is not configured and displays blank/grey. In order for the Ethernet and battery alarms
to work, the corresponding self-test alarms have been enabled under Settings > Product Setup > User-Programmable
Self Tests (not shown). The LEDs can be viewed on the front panel, so adding them to the annunciator is for illustrative
purposes only.
4 Figure 4-42: Annunciator editor and preview window

The three page layouts (3 × 4, 4 × 6, and 6 × 8) select the number of rows x columns of windows that appear in a page.
Annunciator window size and text size shrink as the number of annunciator windows in a page increases.
Properties that can be edited include alarm type (acknowledgeable, latched, self-reset), alarm input (any FlexLogic
operand), text color, and alarm background color.
• Default — Changes all annunciator settings to their factory default values
• Reset — Displays factory default values. Previous settings are not lost unless you save the reset window.
Metering editor
The metering editor is an actual values display tool. It creates pages of actual values for the graphical front panel. There
are two types: tables and phasor diagrams. Tabular actual values pages have settings to configure, while phasor actual
values pages have no settings. Five tabular metering pages can be configured, while there can be a phasor page for each
configured AC source. They display on the graphical front panel using the Metering Tab pushbutton.
The path to the editor is Settings > Product Setup > Graphical Panel > Metering Editor.
Figure 4-43: Metering editor with preview window
4
The inputs are selected at the top. Select from the drop-down list or start typing in the field.
The page, page name, and grid layout are set below the inputs.
Content to display is configured with the cell lines. The content can be actual values, a status indicator, or text.

• Actual value — Select from the FlexAnalogs applicable to the B90, where a FlexAnalog is an analog parameter
• Status — Select from the FlexLogic operands identified in the Status Inputs at the top of the window. An example is to
display text to indicate whether the BATTERY FAIL operand is on or off.
• Text — Enter text to display in the table, for example name of table or column heading
If the metering input is other than OFF, the value of the selected metering input displays, formatted according to the size,
text color, units, multiplier, and decimal configuration. Otherwise either the Text or the Off Text displays depending on the
value of the operand selected by setting Status Input/Index.
A maximum of eight Status Inputs/Indexes can be used per metering page and 16 in all metering pages.
• Default — Changes all actual value settings to their factory default values
Configurable navigation editor

Configurable Navigation is a feature that opens specified pages when specific FlexLogic operands are activated. This
4 feature is useful to open the annunciator page containing an annunciator window that has entered its abnormal state.
In the example shown, failure of any of the three Ethernet ports triggers the Product Information page to display. With
unauthorized access (such as wrong password), IRIG-B clock failure, or breaker trouble, the Event Records display. When a
breaker opens, a single-line diagram displays. For the Ethernet and IRIG-B failure pages to work, these functions also have
been enabled under Settings > Product Setup > User-Programmable Self Tests. For the breaker trouble, the single-line
diagram has been configured.
Figure 4-44: Navigation editor
The path is Settings > Product Setup > Graphical Panel > Configurable Navigation.
The settings consist of 64 field pairs, each with a condition and an activation page. The condition selects any FlexLogic
operand. The activation page selection is the standard set, such as product information, event records, annunciator pages,
and single-line diagrams.
To use the feature, select a CONDITION, select its ACTIVATE PAGE option, then save. When selecting the condition
operand, open the drop-down list and start typing in the field to auto-fill. For example, typing F displays FIRST ETHERNET
FAIL.

• Default — Changes all settings in the window to factory default values

4.2.3 Front panel navigation keys

Display messages are organized into pages under the following headings: actual values, settings, commands, and targets.
The MENU key navigates through these pages. Each heading page is divided further into further submenus.
The MESSAGE keys navigate through the submenus. The VALUE keys increment or decrement numerical setting values when
in programming mode. These keys also scroll through alphanumeric values in the text edit mode. Alternatively, values can
be entered with the numeric keypad.
The decimal key initiates and advances to the next character in text edit mode or enters a decimal point.
The HELP key can be pressed at any time for context-sensitive help messages.
The ENTER key stores setting values.
When entering an IP address on the front panel, key in the first sequence of the number, then press the • key for the
decimal place. For example, for 127.0.0.1, press 127, then •, then 0, then •, then 0, then •, then 1. To save the address, press
the ENTER key. 4
The figure shows the sequence to use to enter a setting. Subsequent sections provide more detail.
Figure 4-45: Front panel keypad use (basic front panel shown)
SETTINGS
PRODUCT SETUP
1. Press to scroll top level:

SETTINGS
MENU 7 8 9
HELP 4 5 6
3. Press to scroll third level fields MESSAGE
2. Press to scroll second level:
ESCAPE 1 2 3 PRODUCT SETUP.
4. Press to scroll through values
ENTER VALUE 0 . +/-
5. Press to save change
842231A1.cdr

These keys and pushbuttons navigate and select items.
Up/Down/Left/Right — These pushbuttons move the selector among the options on a page. The selection is
indicated by a yellow background or a yellow border. On menu pages, the Right pushbutton activates the selected
submenu drilling down the menu hierarchy, and the Left pushbutton backs up the menu hierarchy. These
pushbuttons have a typematic feature on some pages: after a short pause, the pushbutton repeats as long as it is
pressed.
ENTER — Activates the selection on the display, for example a submenu, a control, a keypad key, or a setting. Also
stores updated settings.
ESCAPE — If a setting is open for edit, this pushbutton closes the setting without saving. If a popup menu is open,
this pushbutton closes it. If an item is selected, this pushbutton deselects it. Otherwise this pushbutton activates
the previous page in the page hierarchy.

RESET — Clears all latched LED indications and target messages. When a page with acknowledgeable/resettable
items is displayed, it instead resets/acknowledges all items on that page, or if an item on that page is selected, it
resets/acknowledges that item.
If you reset/acknowledge alarms, they stop flashing but remain in the alarm state as long as that state remains. In
other words, a red alarm does not switch off just because you acknowledged the alarm.
Home — Activates the home page, which is the root page. The page displays product information by default and
is configurable.
Side pushbutton — Five pushbuttons on the left side of the display and five pushbuttons on the right side of the
display. They perform various functions depending on the displayed page, such as switchgear controls. The
display dynamically shows its label next to each side pushbutton when the pushbutton has an assigned function.
These pushbuttons can also be programmed to function as user-programmable pushbuttons 9 to 16.
Tab pushbutton — Five pushbuttons under the display. They navigate through the page hierarchy, and on some
pages activate other actions. The display footer dynamically labels the page or action that is activated by the Tab
pushbutton.
User-programmable pushbutton — Eight physical pushbuttons are associated with the first eight user-
programmable pushbutton elements. Numbering is down, that is, 1 to 4 down the left column and 5 to 8 down the
right column.
These elements control a set of FlexLogic operands that can be used to initiate outputs or select modes. Each
physical pushbutton has an integrated LED indicator that can be user-configured to display the appropriate
status.
4 These pushbuttons have clear covers behind which custom labels can be mounted. A utility is available to print
the labels, under File > Front Panel Report in the software.
4.2.4 LED indicators

The enhanced front panel display provides five columns of LED indicators. The first column contains 14 status and event-
cause LEDs. The next four columns contain the 48 user-programmable LEDs.
The RESET key is used to reset any latched LED indicator or target message, once the condition has been cleared (these
latched conditions can also be reset via the SETTINGS  INPUT/OUTPUTS  RESETTING menu).
The USER keys are not used in this unit.
Figure 4-46: B90 LED panel for enhanced front panel
The status indicators in the first column are as follows:

• IN SERVICE — Indicates that control power is applied, all monitored inputs/outputs and internal systems are fine, and
the relay is in (online) Programmed mode (under Settings > Product Setup > Installation)
• TROUBLE — Indicates that the relay has detected an internal problem. Check the self-test messages outlined at the
end of the Commands and Targets chapter, and view the event records under Actual Values > Records. For a beta /
pre-release, this LED is always on.

• TEST MODE — Indicates that the relay is in test mode. For information, see the Test Mode section in the Settings
chapter.
• TRIP — Indicates that the selected FlexLogic operand serving as a trip input has operated. Set the operand under
Settings > Product Setup > User-Programmable LEDs > Trip & Alarm LEDs. This indicator latches; initiate the reset
command to reset the latch.
• ALARM — Indicates that the FlexLogic operand serving as an alarm switch has operated. Set the operand under
Settings > Product Setup > User-Programmable LEDs > Trip & Alarm LEDs. This indicator never latches.
• PICKUP — Indicates that an element is picked up. This indicator never latches.
The event-cause indicators in the first column are as follows.
Event-cause LEDs are below the status LEDs. They are turned on or off by protection elements that have their respective
target setting selected as either “Enabled” or “Latched.” If a protection element target setting is “Enabled,” then the
corresponding event-cause LEDs remain on as long as the operand associated with the element remains asserted. If a
protection element target setting is “Latched,” then the corresponding event-cause LEDs turn on when the operate
operand associated with the element is asserted and remains on until the RESET button on the front panel is pressed after
the operand is reset.
All elements that are able to discriminate faulted phases can independently turn off or on the phase A, B, or C LEDs. This
includes phase instantaneous overcurrent, phase undervoltage, and so on. This means that the phase A, B, and C operate
operands for individual protection elements are ORed to turn on or off the phase A, B, or C LEDs.
• VOLTAGE — Indicates voltage was involved 4
• CURRENT — Indicates current was involved
• FREQUENCY — Not used
• <blank> — Always off by default
• ZONE 1 — Indicates bus differential zone 1 was involved
• OTHER — Indicates a composite function was involved, BUS 5 OP was asserted, or BUS 6 OP was asserted. For the
B90, a composite function means either any Digital Element OP or any TRIP BUS OP.
The user-programmable LEDs consist of 48 amber LED indicators in four columns. The operation of these LEDs is user-
defined. Support for applying a customized label beside every LED is provided. Default labels are shipped in the label
package of every B90, together with custom templates. The default labels can be replaced by user-printed labels.
User customization of LED operation is of maximum benefit in installations where languages other than English are used
to communicate with operators. See the User-Programmable LEDs section in chapter 5 for the settings used to program
the operation of the LEDs on these panels.

The basic front panel consists of three panels with LED indicators, keys, and a communications port. The RESET key is used
to reset any latched LED indicator or target message, once the condition has been cleared (these latched conditions can
also be reset via the SETTINGS  INPUT/OUTPUTS  RESETTING menu). The RS232 port is for connection to a computer.
The USER keys are not used in this unit.

Figure 4-47: LED panel 1
Status indicators
• IN SERVICE — Indicates that control power is applied, all monitored inputs/outputs and internal systems are fine, and
the relay is in (online) Programmed mode (under Settings > Product Setup > Installation)
4 • TROUBLE — Indicates that the relay has detected an internal problem. Check the self-test messages outlined at the
• TEST MODE — Indicates that the relay is in test mode. For information, see the Test Mode section in the Settings
chapter.
• TRIP — Indicates that the selected FlexLogic operand serving as a trip switch has operated. This indicator always
latches; initiate the reset command to reset the latch.
• ALARM — Indicates that the selected FlexLogic operand serving as an alarm switch has operated. This indicator never
latches.
• PICKUP — Indicates that an element is picked up. This indicator never latches.
Event-cause indicators
Event-cause LEDs are turned on or off by protection elements that have their respective target setting selected as either
“Enabled” or “Latched.” If a protection element target setting is “Enabled,” then the corresponding event cause LEDs
remain on as long as the operand associated with the element remains asserted. If a protection element target setting is
“Latched,” then the corresponding event cause LEDs turn on when the operate operand associated with the element is
asserted and remains on until the RESET button on the front panel is pressed after the operand is reset.
All elements that are able to discriminate faulted phases can independently turn off or on the phase A, B, or C LEDs. This
includes phase instantaneous overcurrent, phase undervoltage, and so on. This means that the phase A, B, and C operate
operands for individual protection elements are ORed to turn on or off the phase A, B, or C LEDs.
• VOLTAGE — Indicates voltage was involved
• CURRENT — Indicates current was involved
• FREQUENCY — Not used
• <blank> — Always off by default
• OTHER — Indicates a composite function was involved, BUS 5 OP was asserted, or BUS 6 OP was asserted. For the
B90, a composite function means either any Digital Element OP or any TRIP BUS OP.

User-programmable indicators
The second and third panels provide 48 amber LED indicators whose operation is controlled by the user. Custom labelling
can be done.
User customization of LED operation is of maximum benefit in installations where languages other than English are used
to communicate with operators. See the User-programmable LEDs section in chapter 5 for the settings used to program
the operation of the LEDs on these panels.
Figure 4-48: LED panels 2 and 3 (index template)
Default labels for LED panel 2

4
The default labels are intended to represent the following:
• GROUP 1...6 — The illuminated GROUP is the active settings group
The relay is shipped with the default label for the LED panel 2. The LEDs, however, are not pre-programmed. To match the
pre-printed label, the LED settings must be entered as shown in the User-programmable LEDs section of chapter 5. The
LEDs are fully user-programmable. The default labels can be replaced by user-printed labels for both panels as explained in
the next section.
Figure 4-49: LED panel 2 (default labels)

The graphical front panel has 14 LEDs. LEDs 1 to 5 are fixed status LEDs, and LEDs 6 to 14 are programmable.
Status indicators
• IN SERVICE — Indicates that control power is applied, all monitored inputs/outputs and internal systems are fine, the
relay’s test mode is disabled, and the relay is in (online) Programmed mode (under Settings > Product Setup >
Installation)
• TROUBLE — Indicates that the relay has detected an internal problem. Check the self-test messages outlined at the

• TEST MODE — Indicates that the relay is in Isolated (solid) or Forcible (flashing) test mode. For information, see the Test
Mode section in the Settings chapter.
• TRIP — Indicates that the selected FlexLogic operand serving as a trip input has operated. Set the operand under
Settings > Product Setup > User-Programmable LEDs > Trip & Alarm LEDs. This indicator latches; initiate the reset
command to reset the latch.
• ALARM — Indicates that the selected FlexLogic operand serving as an alarm input has operated. Set the operand
under Settings > Product Setup > User-Programmable LEDs > Trip & Alarm LEDs.
Figure 4-50: Example of LEDs on graphical front panel
User-programmable event-cause indicators

Event-cause LEDs are below the status LEDs. They are turned on or off by protection elements that have their respective
target setting selected as “Self-Reset” or “Latched.” If set to “Self-Reset,” then the corresponding event cause LED remains
on as long as the operand associated with the element remains asserted. If set to “Latched” and asserted, then it remains
on until the operand is reset and then a reset command initiated.
The LEDs have defaults and can be configured to show instead the status of any FlexLogic operand. The labelling area has
a clear cover behind which custom labels can be mounted. A utility is available to print stick-on labels, as outlined later in
this chapter.
These LEDs are programmed by default as follows:
• PICKUP — LED 6 — Indicates that an element is picked up, and hence a trip can be imminent
• VOLTAGE — LED 7 — Indicates voltage was involved
• CURRENT — LED 8 — Indicates current was involved
• ZONE 1 — LED 9 — Indicates bus differential zone 1 was involved
4.2.5 Front panel labelling

The following procedure requires these pre-requisites:
• The UR front panel label cutout sheet (GE part number 1006-0047) has been downloaded from
http://www.gegridsolutions.com/products/support/ur/URLEDenhanced.doc and printed

• Small-bladed knife
To create custom LED and pushbuttons labels for the enhanced front panel:
1. Start the EnerVista UR Setup software.
2. If not already copied to the Offline Window area, right-click the online device and select the Add Device to Offline
Window option. Click the Receive button in the window that opens to save the settings file to the Offline Window area.
3. Type labels as follows. Select the File > Front Panel Report. The window opens.
Figure 4-51: Enhanced front panel label designer
4. Enter the text to appear next to each LED and above each user-programmable pushbutton in the fields provided. The
LED Offsets and Button Offsets buttons move all labels left/right and up/down on the page (they both do the same
action, so use either button). The Button Offsets button does not display when there are no pushbuttons to customize.
5. Feed the UR front panel label cutout sheet into a printer and press the Print button in the front panel report window.
6. When printing is complete, fold the sheet along the perforated lines and punch out the labels.
7. Remove the UR label insert tool from the package and bend the tabs as described in the following procedures. These
tabs are used for removal of the default and custom LED labels.
Use the tool with the printed side containing the GE part number facing the user.
The label package shipped with every B90 contains the three default labels, the custom label template sheet, and the label
removal tool.
If the default labels are suitable for your application, insert them in the appropriate slots and program the LEDs to match
them. If you require custom labels, use the following procedures to remove the original labels and insert the new ones.

To set up and use the label removal tool:

1. Bend the tabs at the left end of the tool upwards as shown.
Bend the tab at the center of the tool tail as shown.
To remove the LED labels from the B90 front panel and insert the custom labels:
1. Use the knife to lift the LED label and slide the label tool underneath. Ensure that the bent tabs are pointing away from
the relay.

2. Slide the label tool under the LED label until the tabs snap out as shown. This attaches the label tool to the LED label.
3. Remove the tool and attached LED label as shown.
4. Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown.
To remove the user-programmable pushbutton labels from the B90 front panel and insert the custom labels:
1. Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown. Ensure that the bent

tab points away from the relay.
2. Slide the label tool under the user-programmable pushbutton label until the tabs snap out as shown. This attaches the
label tool to the user-programmable pushbutton label.
3. Remove the tool and attached user-programmable pushbutton label.
4. Slide the new user-programmable pushbutton label inside the pocket until the text is properly aligned with the

buttons.
4
After programming LEDs and pushbuttons under Settings > Product Setup > User-Programmable Leds and User-
Programmable Pushbuttons, labels can be created for the front panel.
To create LED and pushbutton labels for a basic front panel:
1. In the EnerVista software, if the B90 is not already listed in the Offline Window area, add it by right-clicking it and
selecting the Add Device to Offline Window option.
2. Click the File > Front Panel Report menu item and select the device.
3. In the Front Panel Report window, double-click an LED or pushbutton slot and type a label. If you need to see the
existing front panel remotely, access Actual Values > Front Panel for the online device. If you need to see the In the
figure, note that labelling is being done for the third set of LEDs because the second panel of LEDs was factory-
labelled.

Figure 4-52: Basic front panel label designer (LEDs shown)
4
4. Optionally save the changes by clicking the Save icon on the toolbar.
5. Click the Print icon on the toolbar. Consider printing to PDF format and adjusting the zoom for appropriate label size,
then print on a physical printer.
6. Cut labels as a block or individually, for example with scissors or an Exacto knife.
7. If there is a plastic cover over the front panel, remove it by gently pushing in on the right side and lifting off the cover.
8. Remove the plastic cover over the LEDs or pushbutton(s) using a screw driver.
9. Insert the labels.
10. Re-attach the plastic covers.

The B90 includes software for labelling the LEDs and pushbuttons on the graphical front panel and a sticker sheet with pre-
printed and blank labels. The pre-printed labels are on the top-left of the template sheet, and the blank labels are on the
bottom-right. Use the pre-printed labels, or use the designer provided in the software and print labels onto the template.
One sheet is provided.
The example shows LED labeling, wjth pushbutton labeling below it (cut off).
To create LED and pushbutton labels for the front panel:
1. In the EnerVista software, in the Online or Offline Window area, access Settings > Front Panel Label Designer or
Front Panel Label Designer (at the product root level). The designer window opens with pre-configured labels.
2. Under File > Print Setup, change the page orientation to Landscape.
3. In the label designer window, delete all labels not wanted for printing. This can be done by clicking the Reset button to
clear all labels, or by selecting each unwanted label and deleting it. Otherwise, all labels displayed print on the
template and use up the template. If you make a mistake, exit the window and open it again to view the default labels.
4. Based on the location on the template on which to print, create the labels by typing in the appropriate slots.

Figure 4-53: Front panel label designer for graphical front panel
5. Click the Print button in the window and select the printer.
6. Once printed, peel the labels off the template and stick them on the front panel. For the enhanced and graphical front
panels, they go over the clear plastic inserts, not under. For the basic front panel, they go under or over the plastic
covers.
Any changes are not saved. Each time that the label designer window opens, the original template displays. Any labels
deleted are not lost.
4.2.6 Menu navigation

Press the MENU key to display selections or home page. Each press of the key advances through the following main
headings:
• Actual Values
• Settings
• Commands
• Targets
• Factory Service
• User displays (when enabled)

The setting and actual value pages are arranged hierarchically. Header display pages are indicated by double scroll bars
(), while sub-header pages are indicated by a single scroll bar (). The header display pages represent the highest level
of the hierarchy and the sub-header display pages fall below this level. Use the down, right, left, and up arrows to navigate
the menu. The MESSAGE up and down arrow keys move within a group of headers, sub-headers, setting values, or actual

values. Continually pressing the MESSAGE right arrow from a header display displays specific information for the category.
Conversely, continually pressing the MESSAGE left arrow from a setting value or actual value display returns to the header
display.
Default values are indicated in this instruction manual in mixed case. In the example shown here, the default access level is
Restricted.
Highest level Lowest level (setting value)
 SETTINGS  SECURITY ACCESS LEVEL:

 PRODUCT SETUP    Restricted

 SETTINGS
 SYSTEM SETUP
Example
 ACTUAL VALUES Press the MENU key until the Actual Values header page appears. This page contains system
 STATUS and relay status information.
4  SETTINGS

Press the MENU key until the Settings header page appears. This category contains settings to
 PRODUCT SETUP configure the relay.

 SECURITY Press the MESSAGE right arrow once to display the first sub-header (Security).


ACCESS LEVEL: Press the MESSAGE right arrow once to display the first setting for Security.
Restricted

 SECURITY Press the MESSAGE left arrow to return to the Security heading.


 DISPLAY Press the MESSAGE down arrow to display the second setting sub-header associated with the
 PROPERTIES Product Setup header.

LANGUAGE: Press the MESSAGE right arrow once to display the first setting for Display Properties.
English

 SETTINGS Press the MESSAGE left arrow to return to the Display Properties page, then again to return to
 SYSTEM SETUP the Product Setup Page. Press the MESSAGE down arrow to move to the next Settings page. This
page contains settings for System Setup.

Access the main menu by pressing the Home pushbutton, then the Menu Tab pushbutton.
Use the Up and Down arrow pushbuttons to select a submenu, then press the Right or ENTER pushbutton to drill into that
submenu. The Left and ESCAPE pushbuttons back up the menu hierarchy.
The Page Up and Page Down Tab pushbuttons also navigate through the list. When there is only a single page of options,
they jump to the first and last entries.
The options displayed depend on order code.

Figure 4-54: Main menu on graphical front panel
4.2.7 Change settings

4
Numerical data
Each numerical setting has its own minimum, maximum, and increment value associated with it. These parameters define
what values are acceptable for a setting.
FLASH MESSAGE For example, select the SETTINGS  PRODUCT SETUP  DISPLAY PROPERTIES  FLASH
TIME: 10.0 s MESSAGE TIME setting.

MINIMUM: 0.5 Press the HELP key to view the minimum and maximum values. Press the key again to view the
MAXIMUM: 10.0 next context sensitive help message.
Two methods of editing and storing a numerical setting value are available.
• 0 to 9 and decimal point — The relay numeric keypad works the same as a calculator. A number is entered one digit at
a time. The leftmost digit is entered first and the rightmost digit is entered last. Pressing the MESSAGE left arrow or
pressing the ESCAPE key, returns the original value to the display.
• VALUE keys — The VALUE up arrow increments the displayed value by the step value, up to the maximum value
allowed. While at the maximum value, pressing the VALUE up arrow again allows the setting selection to continue
upward from the minimum value. The VALUE down arrow decrements the displayed value by the step value, down to
the minimum value. While at the minimum value, pressing the VALUE down arrow again allows the setting selection to
continue downward from the maximum value.
FLASH MESSAGE As an example, set the flash message time setting to 2.5 seconds. Press the appropriate numeric
TIME: 2.5 s keys in the sequence “2 . 5". The display message changes as the digits are being entered.

NEW SETTING Until ENTER is pressed, editing changes are not registered by the relay. Press ENTER to store the
HAS BEEN STORED new value in memory. This flash message momentarily appears as confirmation of the storing
process. Numerical values that contain decimal places are rounded-off if more decimal place digits
are entered than specified by the step value.

Enumeration data
Enumeration settings have data values that are part of a set, whose members are explicitly defined by a name. A set has
two or more members.
ACCESS LEVEL: For example, the selections available for ACCESS LEVEL are "Restricted," "Command," "Setting," and
Restricted "Factory Service."
Enumeration type values are changed using the VALUE keys. The VALUE up arrow displays the next selection while the
VALUE down arrow displays the previous selection.
ACCESS LEVEL: If the ACCESS LEVEL needs to be "Setting," press the VALUE keys until the proper selection displays.
Setting Press HELP at any time for the context sensitive help messages.

NEW SETTING Changes are not registered by the relay until the ENTER key is pressed. Pressing ENTER stores the
HAS BEEN STORED new value in memory. This flash message momentarily appears as confirmation.
4 Alphanumeric text
Text settings have data values that are fixed in length, but user-defined in characters. They can be upper-case letters,
lower-case letters, numerals, and a selection of special characters.
There are several places where text messages can be programmed to allow the relay to be customized for specific
applications. One example is the Message Scratchpad. Use the following procedure to enter alphanumeric text messages.
For example, enter the text “Breaker #1”.
1. Press the decimal point to enter text edit mode.
2. Press the VALUE keys until the character 'B' appears; press the decimal key to advance the cursor to the next position.
3. Repeat step 2 for the remaining characters: r,e,a,k,e,r, ,#,1.
4. Press ENTER to store the text.
5. If you have any problem, press HELP to view context sensitive help. Flash messages appear sequentially for several
seconds each. For the case of a text setting message, pressing HELP displays how to edit and store new values.

When enabling an element in the EnerVista software that outputs to an actual value, the actual values menu is not
updated on the graphical front panel via Ethernet connection when that menu is active on the graphical front panel.
Navigate out and back into the menu for activation.
Numerical data
This example outlines how to change the FLASH MESSAGE TIME setting. Flash messages are status, warning, error, and
information messages displayed in response to certain key presses during settings programming. An example is a
confirmation message upon saving settings. This setting specifies how long to display the message.
Press the Menu pushbutton to display the main menu.

Figure 4-55: Main menu
Use the Up or Down pushbutton to select SETTINGS, then press the Right or ENTER pushbutton.
Figure 4-56: Settings menu 4
With PRODUCT SETUP selected, press the Right or ENTER pushbutton.

Figure 4-57: Product Setup menu
Use the Up or Down pushbutton to select DISPLAY PROPERTIES, then press the Right or ENTER pushbutton.
4 Figure 4-58: Display Properties menu
Use the Up or Down pushbutton to select FLASH MESSAGE TIME, then press the Right or ENTER pushbutton. If the relay is
configured to require login to edit settings, and the user is not already logged in, the login page displays. When the user
has successfully logged in, the setting is opened for edit. As the FLASH MESSAGE TIME setting accepts a numerical value, a
keypad displays. The time is to be changed to 4.0 seconds.
The current setting displays. A flashing cursor line marks the insertion point, initially positioned after the last character of
the setting. The setting range displays under the text.
Press the <-- Move Cursor and Move Cursor --> Tab pushbuttons to move the insertion point. Place it after the 2.
Press the Backspace Tab pushbutton to remove the character to the left of the cursor, in this case the 2.
Using the arrow keys, enter another time, for example 4 for four seconds. These Up, Down, Left, and Right pushbuttons
move the keypad key selector. Pressing the ENTER pushbutton with the - key selected inverts the sign. Pressing the ENTER
pushbutton with the decimal point selected enters that character at the insertion point. Push ENTER now to accept the 4.

Figure 4-59: Settings page with numeric keypad
Press the Save Tab pushbutton, which does a range check on the value, saves the setting when valid, closes the page, and
displays the previous page. 4
When a setting is not saved due to an invalid value, a message flashes, for example being out of range. In cases where the
relay needs to be restarted for settings to take effect, the flash message advises.
Setting entry can be cancelled without impact on the original value by pressing the ESCAPE or Home pushbutton.
Alphanumeric text
Settings that accept alphanumeric values display a keyboard. An example is a pushbutton name.
The &123 key toggles between text and numbers.
The shift key (up arrow on keyboard) is green upon activation, while the keyboard letters switch to upper case. Double-click
the shift key to lock capital lettering, or full capitals.
The globe key (shown greyed-out) toggles the keyboard language between English and another display language selected,
for example between English and French. (The second language needs to be activated under Settings > Product Setup >
Display Properties.)
For Japanese and Chinese, up to 10 characters can be input in a field, not 20.
To add accents, highlight a key and hold the ENTER pushbutton on the graphical front panel. Any special characters
associated with the key display.
Figure 4-60: Settings page with keyboard and accents

4.2.8 View actual values

In addition to data viewable in the Actual Values menu on the front panel, phasor diagrams and metered data can be
displayed. The metered data can be arranged as a table.
The update rate of metered values is 500 ms.
A phasor page for each configured AC Source and up to five user-configurable metering pages can be displayed. The
phasor pages are not configurable. Each phasor page shows a phasor plot and numerical values of all currents, voltages,
and symmetrical components of a single AC source.
The Annunciator and Metering pages can be configured to display data. Each has a user-configured number of rows and
columns. Each cell can include either configurable static text or the value of a selected FlexLogic operand, FlexAnalog
operand, or actual value.
To display a metering page, press the Home pushbutton, then the Metering Tab pushbutton. The first metering page
opens, with phasor pages listed before tabular pages. The Tab pushbuttons display any other metering page, as do the Up,
Down, Left and Right pushbuttons. The current page is highlighted with a blue Tab pushbutton.
Each phasor page has a name, which consists of the value of the SOURCE NAME # setting appended with " Phasors."
Phasor pages that have no configured CTs or VTs do not have a Tab pushbutton, and phasor pages that have no
4 configured cells cannot be displayed.
Figure 4-61: Phasor display
The configurable name displays in the header and Tab pushbutton label. Factory default names are Page 1, Page 2, and so
on.

Figure 4-62: Metered actual values
The phasor sources are configured under Settings > System Setup > Signal Sources. The tables to display the actual
values are configured in the software under Settings > Product Setup > Graphical Panel > Metering Editor.
4
4.2.9 Change passwords

The information in this section refers to password security. For information on how to set the password for the first time or
change CyberSentry passwords, see the previous chapter or the Settings > Product Setup > Security > CyberSentry section
in the next chapter.
The B90 supports password entry from a local or remote connection.
Local access is defined as access to settings or commands via the front panel. This includes both keypad entry and the
RS232 port. Remote access is defined as access to settings or commands via any rear communications port. This includes
both Ethernet and RS485 connections. Any change to the local or remote password enables this functionality.
corresponding connection password. If the connection is to the back of the B90, the remote password must be used. If the
connection is to the RS232 port of the front panel, the local password must be used.
There are two user security access levels, setting and command, for which you can set a password for each. Use of a
password for each level controls whether users can enter commands or change settings. Another option is to specify
setting and/or command access for individual user accounts.
• Setting — Allows the user to make any changes to any of the setting values:
– Changing any setting
– Test mode operation
• Command — Restricts the user from making any settings changes, but allows the user to perform the following
operations:
– Changing the state of virtual inputs
– Clearing the event records
– Clearing the oscillography records
– Changing the date and time
– Clearing the data logger
– Clearing the user-programmable pushbutton states
To enter the initial setting or command password:
1. Press the MENU key until the SETTINGS header flashes momentarily and the PRODUCT SETUP message appears on the

LOGIC DIAGRAMS CHAPTER 4: INTERFACES
display.
2. Press the MESSAGE right arrow until the ACCESS LEVEL message appears on the display.
3. Press the MESSAGE down arrow until the CHANGE LOCAL PASSWORDS message appears on the display.
4. Press the MESSAGE right arrow until the CHANGE SETTING PASSWORD or CHANGE COMMAND PASSWORD message
appears on the display.
 SECURITY ACCESS LEVEL:
  Restricted
 CHANGE LOCAL CHANGE COMMAND

  PASSWORDS  PASSWORD: No
CHANGE SETTING
 PASSWORD: No
5. After the CHANGE...PASSWORD message appears on the display, press the VALUE up or down arrow to change the
selection to “Yes.”
6. Press the ENTER key and the display prompts you to ENTER NEW PASSWORD.
7. Type in a password and press the ENTER key.
8. When VERIFY NEW PASSWORD displays, re-type the password and press ENTER.
4 CHANGE SETTING
PASSWORD: No
CHANGE SETTING ENTER NEW VERIFY NEW

PASSWORD: Yes PASSWORD: ########## PASSWORD: ##########
NEW PASSWORD
HAS BEEN STORED
9. When the NEW PASSWORD HAS BEEN STORED message appears, your new Setting (or Command) password is active.
4.2.10 Invalid password entry

By default, when an incorrect Command or Setting password has been entered via the front panel three times within five
minutes, the LOCAL ACCESS DENIED FlexLogic operand is set to “On” and the B90 does not allow settings or command level
access via the front panel for five minutes.
By default, when an incorrect Command or Setting password has been entered via any external communications interface
three times within five minutes, the REMOTE ACCESS DENIED FlexLogic operand is set to “On” and the B90 does not allow
settings or command access via the any external communications interface for five minutes. The REMOTE ACCESS DENIED
FlexLogic operand is set to “Off” after five minutes for a Command password or 30 minutes for a Settings password.
These default settings can be changed in EnerVista under Settings > Product Setup > Security.
4.3 Logic diagrams

Logic diagrams in this instruction manual provide an overview of function and settings. A logic diagram is based on
• Inputs-on the left side, which are setting and operands
• Logical gates, which is Boolean algebra to combine logical lines using AND, OR, NOT, and other gates to get a new
logical state
• Logical operators, which are timers, one-shot operations, latches, and so on
• Outputs-on the right side, which are products of the manipulations with inputs, logical gates, and logical operators to
produce new operands and define the output state of the element
True and false values are denoted by 1 and 0 respectively. A function usually is high/on/enabled when 1.

CHAPTER 4: INTERFACES FLEXLOGIC DESIGN USING ENGINEER
Reading from right to left in the following diagram, the TRIP BUS 1 OP and TRIP BUS 1 PKP FlexLogic operands on the right side
are triggered when either the settings or reset latch in the middle of the diagram is triggered. When this applies, the TRIP
BUS 1 OP operand is triggered after the delay set by the TRIP BUS 1 PICKUP DELAY or TRIP BUS 1 RESET DELAY setting, while the
TRIP BUS 1 PKP operand initiates immediately. The settings or reset latch in the middle of the diagram is triggered as follows.
• For the reset, one of three conditions are required to meet the OR requirement shown at the bottom left. That is, the
TRIP BUS 1 LATCHING setting must be 0=Disabled (which is negated by the NOT function to become 1=Enabled), output
from the TRIP BUS 1 RESET FlexLogic operand must be 1, or output from the RESET OP FlexLogic operand must be 1.
• For the settings, one of 16 input conditions at the top left must be met for the OR, the TRIP BUS 1 FUNCTION must be
Enabled, and the TRIP BUS 1 BLOCK output must output as 0, which is then negated/reversed by NOT to become 1.
Table 4-2: Logic diagram symbols
Symbol Description
= Off Output from FlexLogic operand, so user-defined
= Enabled 1 = Enabled and 0 = Disabled
OR Any function input on the left side satisfies the condition
AND All functions input on the left side are required to satisfy the condition
 Not. Negates/reverses the output, for example 0 becomes 1.
 Connection
S, R Set, Reset 4
TPKP Timer pickup. Triggered by the settings latch in the diagram.
TRST Timer reset. Triggered by the reset latch in the diagram.
Figure 4-63: Logic diagram

SETTINGS
TRIP BUS 1 INPUT 1
SETTINGS
= Off
TRIP BUS 1 PICKUP
TRIP BUS 1 INPUT 2
DELAY
= Off Non-volatile,
TRIP BUS 1 RESET
OR set-dominant
***
DELAY
AND S TPKP FLEXLOGIC OPERAND
TRIP BUS 1 INPUT 16 TRIP BUS 1 OP
Latch
= Off TRST
R
SETTINGS
TRIP BUS 1 FLEXLOGIC OPERAND
FUNCTION
TRIP BUS 1 PKP
= Enabled
TRIP BUS 1 BLOCK AND
= Off
SETTINGS
TRIP BUS 1
LATCHING
= Enabled
TRIP BUS 1 RESET
= Off
OR
FLEXLOGIC OPERAND
RESET OP 842023A1.CDR
4.4 FlexLogic design using Engineer

Parts of EnerVista Viewpoint Engineer software are integrated in the EnerVista UR Setup software. Engineer can be used to
create and modify FlexLogic that is used by a device, such as to monitor output, monitor triggers, and create self-tests.
Features include

FLEXLOGIC DESIGN USING ENGINEER CHAPTER 4: INTERFACES
• Automatically displays existing FlexLogic

• Drag-and-drop interface
• Open multiple tabs and edit simultaneously
• Display symbols in IEC, ISO, or UR formats
• Export a diagram as BMP file or copy it to the clipboard for import into other applications
• Scale and print files in various paper sizes
• Works with all UR firmware versions
The figure shows an example where several inputs are used to trigger an output. With the OR function, any one of the
inputs can trigger the output.
Figure 4-64: Inputs triggering output in Engineer
The process is as follows:

• Modify or create a logic diagram in the Offline Window area of the EnerVista UR Setup software
• Compile it and troubleshoot any errors
• The logic populates automatically into the FlexLogic Equation Editor

• Upload the file to the live device

• Monitor the output
This section explains how to use Engineer. It outlines the following topics:
• Design logic
• Send file to and from device
• Monitor logic
• View front panel
• Generate connectivity report
• Preferences
• Toolbars
4.4.1 Design logic

FlexLogic can be created with a block diagram. Note that although work is completed in the Offline Window area of the
software, communication occurs with the online device, for example when switching to monitoring mode.
•
•
Examples
Add existing FlexLogic equations
4
• Create a logic diagram/sheet
• Rapidly add logic blocks in sequence
• Connect two logic diagrams/sheets
• Optimize the logic
• Change logic order
• Search logic
• Exclude sheet from compile
4.4.1.1 Examples
The symbols are displayed in the UR format.
Create oscillography trigger every three minutes

Figure 4-65: Three-minute timer turns on LED for 10 seconds
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, the first and second virtual outputs are named
OscTrigger
Top logic — Three-minute timer trigger
Bottom logic — Turn on LED 1 for 10 seconds when the trigger starts

Create data logger trigger every seven minutes

Figure 4-66: Seven-minute timer turns on LED for 10 seconds
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, virtual outputs 3 and 4 are named DLTrigger
Top logic — Seven-minute timer trigger
Bottom logic — Turn on LED 9 for 10 seconds when the trigger starts
Create events every minute, then every 100 ms

Figure 4-67: One-minute timer turns on LED and creates events every 100 ms
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, virtual output 5 is named EVStart, 6 is named
EVTriggered, and 7 is named EVMakeEvent
Top logic — One-minute timer trigger
Middle logic — Turn on LED 17 for 10 seconds when trigger starts
Bottom logic — Create events at 100 ms intervals for the same 10 second period
4.4.1.2 Add existing FlexLogic equations

A logic diagram can be created using existing FlexLogic equations (this section) or by creating new ones (next section).
When using existing equations, you modify them in the FlexLogic Equation Editor in the Offline Window area, then apply
them.
The FlexLogic Equation Editor window is in view-only mode when the Logic Designer is open. To instead work in the
FlexLogic Equation Editor, close the Logic Designer window, then re-open the FlexLogic Equation Editor.
To create a logic diagram using existing FlexLogic equations:

1. In the Offline Window area, modify the FlexLogic for the device under FlexLogic > FlexLogic Equation Editor. If the
device is not listed, right-click the device in the Online Window area and select the Add Device to Offline Window

option.
Upon saving the modified FlexLogic, a yellow icon appears for the device in the Offline Window area to indicate that
the logic differs from the Online device.
2. In the Offline Window area, access Engineer for the device, then Logic Designer. The logic opens.
3. Click the Edit > Auto Populate Workbook menu item. If the software prompts if you want to keep or discard existing
sheets, either is acceptable, with the older excluded sheeted being denoted by brackets, such as < Sheet 1 >. The logic
displays in the various tabs. The FlexLogic created in the equation editor appears in Sheet 1, for example.
4.4.1.3 Create logic diagram

Upon access of the Logic Designer, the FlexLogic equations of the device display. You can create new logic in new sheets or
modify the ones that display.
This procedure uses input / output logic as an example.
To create a logic diagram:
1. In the Offline Window area, access Engineer for the device, then Logic Designer. If the device is not listed, right-click
the device in the Online Window area and select the Add Device to Offline Window option.
Figure 4-68: Access Engineer in the Offline Window area
A default block diagram opens that shows 48 inputs (boxes) and 48 user-programmable LEDs (circles).
For the graphical front panel, no LEDs can be added to the window and the LEDs are removed when opening any
existing files. For these existing files with the LEDs removed, save the file without them.

Figure 4-69: Default view of FlexLogic designer
2. Optionally delete the default logic diagram by right-clicking its tab at the bottom of the window and selecting Delete.
3. To add a blank sheet, click Edit > Add Sheet. A new tab displays. Or use the last tab displayed, which is a blank sheet.
4. Optionally right-click the new tab and Rename it.
5. Add the input blocks to the logic diagram. For example, click the I/O Tokens tab on the right, click the Input element,
then click in the logic sheet to add it. Or drag-and-drop it.
6. Double-click the block on the sheet to configure it, selecting from the two drop-down lists. The figure shows that
virtual input 61 is being added. The View Associated Screen button opens its settings window.
Figure 4-70: Configuring an input block
7. Add the output blocks to the logic diagram. For example, click the I/O Tokens tab, click the Virtual Output element,
then click in the logic sheet to add it. Double-click the block on the sheet to configure it. For the name, make it unique.
The figure shows virtual output 61 is being added, with a suffix of "io" added to the name to make it unique. Note that

the outline color of a block is red until it is configured, and that this properties window varies by block and the
selectable options by order code.
Figure 4-71: Configuring an output block
4
8. Connect the input blocks to the output blocks by drawing a line as follows. Click at the end of one block and drag the
line to the next block. Or click the Drawing Tools tab, then select the Line option. The cursor needs to be at the
connection point to end the line, not elsewhere on the block. Note that the outline color is no longer red on the blocks.
Figure 4-72: Completed inputs and outputs
9. Add any remaining blocks or information. Right-click a block to copy and paste it. Notes are as follows.
Add a text box — Drawing Tools > Text
Add a FlexElement — Elements > FlexElement. An analog input is expected where a small arrow head shows in the
box.
Figure 4-73: FlexElement accepts analog inputs on left side where arrow heads display
Add an Element — Elements tab. Available elements reflect the product, for example the Control Elements category.

Figure 4-74: Elements reflect Control Elements
10. Check for any blocks that have a red outline. These are invalid. Fix them before continuing, for example by configuring
them.
11. Compile the logic diagram to check for errors by clicking the Compile button at the bottom left or by pressing the F7
key.
4 If prompted about a message about sorting, click Yes to apply the default (for this example), which can be automatic
sorting based on an algorithm that applies fastest execution time.
With successful compiling, the file is saved and the FlexLogic equations populate automatically. Scroll up through the
compile messages, with the red errors being the only messages that require fixing before proceeding.
The figure shows that we forgot to add the "Io" suffix to the names of virtual outputs 62 and 63, as indicated by
"Warning: Virtual output xx using default name." This warning is a minor warning.
The warning "input using disabled feature" means that input needs to be enabled. Double-click the block, click the
View Associated Screen button, enable the setting, save, and recompile.
The output and messages are explained in the next section.
Some information displayed in the compile messages updates automatically, for example messages after a device is
unplugged.
Figure 4-75: Compile and check the logic
12. View the FlexLogic equations by navigating in the Offline Window area to FlexLogic > FlexLogic Equation Editor. The
window opens with the entries displayed in the next tab.

Figure 4-76: Logic displayed in FlexLogic Equation Editor
13. Save the work.

The logic diagram has been created and the FlexLogic equations populated. The next steps are to upload the file to the
device and to monitor the device.
4.4.1.4 Compiled results and warning messages

When a yellow caution symbol displays in the Offline Window area, it means that the settings file is not synchronized with
the online device. Right-click the device in the Offline Window area, and select the Update SCL files option. SCL refers to
the Substation Configuration Language. An Instantiated IED capability description (IID) file is an example of an SCL file and
contains the actual settings on a UR device.
Figure 4-77: Settings files not synchronized between offline and online files 4
When the Update SCL files option is selected, the CID and IID files in the device folder are updated by the user
configuration in the IEC 61850 panel and thereby become synchronized. The CID file and the IID file (depending on the
preference 'Do not update IID file when updating SCL files') are updated. If the CID file is not already there, it is generated.
The location of these files is C:\ProgramData\GE Power Management\urpc, for example, in the Offline and Online folders.
Any FlexLogic equations entered in the Offline Window area are erased. The logic drawn in the Logic Designer window in
Engineer in the Offline Window area remain. The warning icon disappears after updating.
The following information is contained in the compile window.

Figure 4-78: Compiled results
Number of Lines Saved — The number of compiled logic lines eliminated by using the optimization algorithm, as set in the
Optimize Compiled Output option of the Preferences. In the example shown, no lines were saved because the optimizer is
disabled.
FlexLogic Lines — The number of lines that the compiled logic uses, for example seven of 512 available.
Virtual Output equations — The number of FlexLogic equations used in the Logic Designer window.
Timers used — The number of timers used in the Logic Designer window.
Memory Used — The percent of memory used in the Logic Designer window.
Errors
Table 4-3: Errors from compiling
Category Block or gate Message Description
affected
Error All Number of lines (nnn) exceeds The compiled result exceeds the limit of 512. Reduce the number of
maximum limit of 512 equations to 512 or less.
Error Tag-In Tag-in not configured (TAG_ID, A Tag-In is connected to a circuit but the Tag-In is not referencing an
SheetReference) existing Tag-Out
Error 1 Shots One Shot is over limit The number of One-Shots contained within all of the VO blocks has
(SYMBOL_ID, SheetReference) exceeded the maximum allowed for the firmware revision. This value can
either be 0 or 32.
Error =VO VO has no inputs (VO_ID, A Virtual Output block is located within the FlexLogic diagram and there
SheetReference) is no block connected as input to it. Connect and identify the inputs.
Error Timer Timer used more than once The same timer is used in more than one place in the editor. This means
(TIMER_ID, SheetReference) either the circuit that the Timer belongs to has been branched, or the
Timer has been duplicated.

Category Block or gate Message Description

affected
Error Input Unrecognized Parameter An Input symbol is configured to an item that is not recognized by the
(SYMBOL_ID,Name,SheetRefere current order code and version. Possible cause: The order code and/or
nce) version of the settings file was converted causing the input parameter to
become unavailable.
Warnings
When using the 'Reset OP' operand, a warning can appear indicating that this is a disabled feature. This means that the
Reset Settting's FlexLogic operand is set to OFF. Resetting of the relay can be done by pressing the reset button on the front
panel of the relay or by sending a Reset command through communications.
Table 4-4: Warning messages from compiling
Category Block or Message Description
gate
affected
Minor warning Input Input set to unused VO An Input symbol is using an unassigned Virtual Output
(SYMBOL_ID,Name,Sheet)
Major warning Tag-Out Tag-out not connected A Tag-Out symbol has no input
(TAG_ID,Sheet)
Major warning All Symbol not connected
(SYMBOL_ID,Name,Sheet)
A symbol’s input and/or output is not connected and is not part of a
VO block. Draw the input and/or output to the block.
4
Minor warning =VO Virtual Output n using default The Assigned Virtual Output is using the default name. Change the
name (VO_ID,Sheet) name.
Minor warning Input Input using default name An Input symbol is using a Contact Input, Contact Output, Digital
(SYMBOL_ID,Name,Sheet) Element, FlexElement, or Digital Counter set to the default name.
Change the name so that it is unique.
Setting warning Input Input using disabled feature An Input symbol is using a disabled Virtual Input, Contact Input, Digital
(SYMBOL_ID,Name,Sheet) Element, FlexElement, Digital Counter, Control Pushbutton,
Programmable Pushbutton, Contact Output, or Protection/Monitoring
Element. Enable it and try again.
Major warning Input Input set to OFF An Input symbol is set to OFF
(SYMBOL_ID,Sheet)
Major warning Input Input set to ON An Input symbol is set to ON
(SYMBOL_ID,Sheet)
Setting warning Input Contact Output Operate is OFF The symbol block is using the default setting of OFF
(SYMBOL_ID, Contacts)
Setting warning Input Contact Output Seal-In is OFF The symbol block is using the default setting of OFF
(SYMBOL_ID, Contacts)
4.4.1.5 Rapidly add logic blocks in sequence

Blocks are added by clicking an element then clicking in the drawing area, or by dragging and dropping the element onto
the canvas. Blocks can be added rapidly in sequence, for example when you have inputs 1 to 10, without having to select
the element each time.
To rapidly add logic blocks:
1. In Engineer, click File > Preferences. The window opens.
2. Click the Editor entry.
3. Enable the Repeat Symbol check box.
4. Click the Ok button to save and exit from the window.
5. In the logic diagram, select an element, then click in the drawing area to add it, click again to add a second box, and
so on.

4.4.1.6 Connect two logic diagrams

When the logic is complex and requires two sheets, for example, these two sheets can be connected. By connecting them,
the logic is continuous from one sheet to the next.
To connect two logic diagrams:
1. In the first sheet, click the I/O Tokens tab.
2. Scroll to the bottom, and click and drag the Tag Out element to the sheet where the next sheet is to connect.
3. Double-click the element and in the window that opens, give it a name, such as "To Sheet 2" or "To IO Sheet 2."
Figure 4-79: Connecting sheet 1 to sheet 2
4. In the second sheet, click and drag the Tag In element to the sheet where the first sheet is to connect.
5. Double-click the element and in the window that opens, select the first sheet from the drop-down list to connect the
two sheets.
6. Save the work.
4.4.1.7 Optimize the logic

The number of available FlexLogic entries depends on firmware, for example 515 or 1024 lines. The software can
automatically optimize a logic diagram to reduce space and free up entries.
To optimize the logic:
1. In Engineer, under File > Preferences, select the Compiler option. Ensure that the Optimize Compiled Output option is
enabled.
2. Run the compiler again, for example by clicking the Compile button at the bottom left of the software. The results
display in the Optimization Summary. Changes also display when the FlexLogic Equation Editor is accessed. The logic
diagram does not change. In the example shown, no lines were saved to free up space.
Figure 4-80: Code optimization results

4.4.1.8 Change logic order

The order in which the FlexLogic is populated in the FlexLogic Equation Editor window depends on settings.
First, when automatic sorting is not enabled, the sequence in which the blocks were drawn is followed.
Second, the order in which equations are executed can be manually changed, as outlined here.
Third, automatic sorting can be set in preferences, as outlined here. It is enabled by default and means that an algorithm is
implemented to give best results and quickest performance, For example, the block with the fastest execution time is
entered first in the FlexLogic. When two block functions have the same execution time the block drawn first displays first in
the FlexLogic. For example, drawing input 61 to output 61, then input 62 to output 62 causes the input/output 61 to be
entered into the FlexLogic first. Automatic sorting takes precedence over manual sort; if you enable this option, manual
sorting is not implemented.
To manually change logic order:
1. In the compile area, click the VO Order tab.
2. If the window is blank, click the Refresh button.
3. Select an entry and click the up or down arrow. To cancel any manual changes, click the Sort or Refresh button.
4. Recompile. The change is not executed or saved if automatic sorting is enabled.
Figure 4-81: Ordering FlexLogic entries
4
To set automatic sorting:

1. In Engineer, under File > Preferences, select the Compiler option. The Automatically Sort VOs option means that the
block with the fastest execution time is entered first in the FlexLogic. When two block functions have the same
execution time the block drawn first displays first in the FlexLogic. For example, drawing input 61 to output 61, then
input 62 to output 62 causes the input/output 61 to be entered into the FlexLogic first.
4.4.1.9 Search logic

Items that can be searched in a logic diagram include gates, Input, Contact Input, Contact Output, Timer, Virtual Output,
Tag In, Tag Out, and User-programmable LED. A search can be performed while designing or monitoring.
To search:
1. In the compiler area of Engineer, click the Search tab.
2. Use one of the following methods to set search criteria:
– Select an element from the first drop-down list. Results display automatically.
– Type in the second text string box, or select any of the 32 previous searches from the drop-down list. Click the
Search button. Any results display.
The search applies to all tabs, not just the active tab.
3. Double-click a search result to view the item.

Figure 4-82: Search function
You can also select an element from the drop-down list on the toolbar. It is then highlighted in the logic diagram.
4.4.1.10 Exclude sheet from compile

While designing the FlexLogic equations, entire sheets can be removed from the compile logic. This allows the user to test
various schemes by placing schemes on separate sheets and including either sheet at compile time.
4 To exclude a sheet:
1. In the Logic Designer window, right-click the tab and select the Exclude from Compile option so that the check mark
displays. When sheets are excluded, a message displays with each compile that "excluded sheets will not be reflected
in the RPN." An excluded sheet is denoted with end brackets, similar to < Sheet 1 >.
Figure 4-83: Excluding a tab from compiling
Figure 4-84: Tab excluded from compiling
4.4.2 Send file to and from device

With the logic diagram created, compiled, and errors eliminated, the FlexLogic can be sent to a live device. And,
conversely, a file from a live device can be added to the Offline Window area for additional work.
To send a file to a device:
1. In the Offline Window area of the software, right-click the device name and select the Write Settings to Device option.
A prompt can appear that the URS file has been repaired; acknowledge the message.
2. When a window opens, select the device to which you want to send the file, then click the Send button and confirm.
The order codes and IEC 61850 edition must match. The file is sent to the live device. Any errors can be viewed in the

log file at the prompt.
To import a file from a device:

1. Close all open files in Engineer that relate to the device, else a message displays to that effect, for example to close
the FlexLogic view associated with the file. When the file is not associated with a live device, a message displays to
that effect; you need to identify the device to which you want to send the file. The order codes must match.
2. Right-click the device in the Online Window area and select the Add Device to Offline Window option. After you enter
a name for the file, it is written to the Offline Window area.
4.4.3 Monitor logic

After creating the logic diagram, validating it, and uploading the FlexLogic to a device, the results from the device can be
viewed.
The following checks are performed automatically when switching from design to monitoring, and prompts display when
necessary:
• Verify that the order code of the linked relay matches the settings file
• Verify that the version of the linked relay matches the settings file
• Verify that the FlexLogic Equation Editor of the linked relay matches the settings file. Solution: Compile the FlexLogic 4
logic diagram and send the settings file to the relay.
• Verify that the FlexLogic Timers of the linked relay match the settings file. Solution: Compile the FlexLogic logic
diagram and send the settings file to the relay.
• If the settings file contains a serial number lock, then verify that the serial number of the linked relay matches the
settings file
To view results:
1. In the Offline Window area of the software, expand the Engineer entry for the device.
2. Double-click the Logic Designer entry and Compile the logic.
3. Double-click the Logic Monitor entry, or click the M button in the toolbar at the top of the window. With successful
launch, the logic displays and a green indicator displays at the bottom of the tab.
When the file is not associated with a live device, a message displays to that effect; you need to identify the device to
which you want to send the file. The order codes must match between the Offline Window and the Online Window.
When the device is offline, a message indicates problems communicating with the device.
When the devices are not synchronized, a message indicates the FlexLogic does not match the settings file. To send
the offline file to the device, right-click the device name and select the Write Settings to Device option.
When the state of a symbol is OFF, the symbol is shown in the default color or no color.
When a symbol's state changes to ON, the symbol and connection line turns green.
The state of some symbols can either be unknown or the state transitions faster than the update interval. For these
two cases, the state of the symbol is considered 'UNKNOWN' and the symbol is outlined in red.
The colors for the ON and Unknown state can be customized in the Preferences.
The figure shows that the software is communicating with devices (square green indicator) and that a minor error is
present (green box outline). In this case, the battery is weak and needs to be replaced. This can be viewed as the
Replace Battery message on the front panel of the device and in the EnerVista software under Actual Values > Front
Panel > Front Panel or Display/Keypad.

Figure 4-85: Monitoring a device, with minor error caused by weak battery
4.4.4 View front panel and print labels

This window displays the LEDs that are on the front panel. You can create labels and print them for the device. You do not
use the window to add text labels and upload them to the device. Custom labelling is also outlined earlier in this chapter;
4 see the Front Panel Labelling section.

To view the front panel:
2. Double-click the Front Panel Report entry. The report displays. The Device Summary is read from the settings file and
cannot be changed. The LEDs and pushbuttons display below the summary.
3. To save the report, click File > Save As, enter a file name, and select the front panel report (FPR), JPG, or PDF format.
Figure 4-86: Front panel display in Engineer
To print labels:
1. In the Front Panel Report window, double-click an LED or pushbutton and enter text.
2. To print the labels, click the Print icon on the toolbar.
3. To save the report and labels, click File > Save As, enter a file name, and select the FPR, JPG, or PDF format.
4. Use the instructions in the second tab of the window to add the labels to the physical device.

4.4.5 Generate connectivity report

This report displays basic information about a device, such as order code, port numbers, inputs and outputs. You can use it
to create a PDF file of basic information. The report is based on CID and/or IID files, and not the system or full SCD. All
device details including Remote Inputs, Remote Outputs, and Analog Inputs/Outputs are indicated, including quantities
used and available.
To display a device report:
2. Double-click the Device Connectivity Report entry. The report displays.
3. To save as a PDF file, click File > Save As.
Figure 4-87: Device Connectivity Report
4.4.6 Preferences
Preferences determine functionality. As such, you are encouraged to review them. This section outlines some options
available in the menus and preference panels.
Access them in the Logic Designer panel under the View menu and under File > Preferences. The Logic Designer and
Logic Monitor preferences are outlined here, not all preferences for a device.
4.4.6.1 View menu

View > Toolbar > Advanced Actions — Active when in Logic Designer. Toggles a toolbar to nudge, rotate, flip, or change
the order of an element.
View > Show Unused Pins — Enable to display unconnected pins. Disable to eliminate unconnected pins from the view, for
example when printing.

Figure 4-88: Unused pins on and off
4.4.6.2 Logic designer

The path is File > Preferences > Logic Designer.
Workbook Setup
Size and Units

Size and Units — Changes the size of diagram area displayed in Engineer. If you set the size to be smaller than an existing
logic diagram, the content is cut off.
4 WorkBook
Print Scale — The scale for logic diagram when printing. Scaling a large diagram to 200 percent, for example, results in the
diagram being cut off.
Orphan Protection — When enabled, the printing output prevents Virtual Output circuits from spanning more than a single
page. The largest Virtual Output circuit is scaled to fit on a single page and all remaining Virtual Output circuits are scaled
so that all circuits are printed using the same scale.
Show Title Block — When enabled, places an information box at the bottom right of the diagram when printing. Enter the
information in the File Information panel.
Show Sheet Name — When enabled, shows Sheet 1, Sheet 2, or any other name at the top of the logic diagram when
printing.
Start Sheet On New Page — Places the sheet on the next page when printing.
Show Notes Selection — When other than None, prints the text from any information notes added to the document (under
Drawing Tools tab > Note). The text is printed after the logic diagram.
File Information
The text entered here displays at the bottom right of a diagram when printing, provided that the Show Title Block option is
enabled. Note the option to change the logo from the GE logo to your company logo.
Display
The panel sets how the element boxes display. The figure shows how an AND gate displays when the UR default, IEC, or
ISO symbol type is selected.
Figure 4-89: AND gate varies by standard selected
Symbol Style — IEC, ISO, UR Setup — Sets how the gates display in the logic diagram.
Symbol Color — When set to Black & White, only logic blocks with issues continue to display red.
Zoom Operation — Determines what happens when the View > Zoom functions are used. When set to Sheet Only and the
zoom is changed, the single tab changes. When set to Workbook, all tabs change.

Editor
Repeat Symbol — Enable this feature to add element blocks rapidly in sequence, for example when you have inputs 1 to
10, without having to select the element each time. Select the element block from the toolbox, click the diagram, then
continue to click to add additional blocks.
Use first available VO / Timer — When enabled and you copy and paste a virtual output or timer element, the numbering
continues in sequence. For example, you copy timer 5 and paste it as timer 6. When disabled and you copy and paste a
virtual output or timer element, the same number is used. For example, you copy timer 5 and paste it as timer 5.
Auto-Save Logic Designer every x minutes — Logic diagrams with changes are saved automatically according to this
interval. The range is 5 minutes (default) to 30 minutes. With auto-save, the file extension of the saved file is .auto. This file
remains until you save the file manually.
Auto Populate
These options work in the Edit > Auto Populate Workbook function.
VOs per Worksheet — When an existing settings file is opened in the Logic Designer, the Logic Designer populates the
canvas and attempts to evenly distribute the Virtual Output circuits across multiple sheets. A value of 100 in this setting
places all FlexLogic equations on a single sheet until there are 100, then the next ones are placed on another sheet. A value
of 1 places each Virtual Output circuit on a separate sheet.
Show / FlexLogic Merge / Show Unused — If Show Contact Outputs and Show LEDs are selected, for example, the function
places Contact Output and User-programmable LED symbols for settings that are configured. If you disable the LED check
4
boxes, then the LED tab/sheet does not display when you next open the Logic Designer window. The settings apply to all
products, not just the active window when it is next opened. Close then reopen the Logic Designer window for the setting
to take effect.
Compiler
Show Warnings — Options to filter the messages that display when logic compiles.
Minor — Enable to display minor errors. An example is using the default values of an element added to the diagram, such
as the name of the element. An example is "Warning: Virtual output xx using default name," for which you simply click into
the element to rename it.
Major — Enable to display major errors. Examples are an input that does not have a corresponding output, using disabled
features, and failing to connect a symbol. Fix these errors.
Setting — Enable to display error message related to settings, such as an improperly configured setting, such as using ON
or OFF.
Automatically Sort VOs — When enabled, the logic is compiled with an algorithm to give best results and quickest
performance, for example the fastest logic first. The fastest logic displays in the FlexLogic Equation Editor output as the
first entries in the table. Use sorting when virtual outputs have dependencies on other virtual outputs. This setting takes
precedence over order set manually in the VO Order tab in the compiler.
When disabled, the sequence in which the blocks were drawn is followed.
Optimize Compiled Output — With this option enabled, the software automatically optimizes a logic diagram to reduce
space and free up FlexLogic entries. Run the compiler again, for example by clicking the Compile button at the bottom left
of the software. The number of saved lines displays in the Optimization Summary. Changes also display when the FlexLogic
Equation Editor is accessed. The logic diagram does not change.
4.4.6.3 Logic monitor
Display
The software displays the color specified when an element is on. There is no color when the element is off.
The software displays another color when the status cannot be determined and is unknown.

Timing
Timing Information can be displayed in the monitoring window. This timing information is only an approximate
representation of how Engineer sees transitions. Use the device's Event Record to view accurate timing information.
The timing information can also be streamed to a comma-separated values (CSV) spreadsheet.
The timing information displayed and recorded can be filtered based on six categories. If a category is not selected, any
timing information related to that category does not display and is not recorded to the CSV file.
Show Timing Information in Output Window — Enable to display times in the monitoring window.
Because of the update rate of the Logic Monitoring, the timing information cannot be used as an accurate representation
of the events that occur within the relay. Use instead the device's event record. Timing information can be delayed by 30
seconds.
Save Timing Information to CSV File — Enable to write timing information in a spreadsheet. The timing information is
recorded in a text file that uses commas to separate each of the fields. This file uses the extension CSV that is supported by
any spreadsheet application.
Every change written to the CSV file requires a timestamp.
The format for the timing information in the output window is as follows:
yyyy/mm/dd hh:dd:ss
4 devicename offline
yyyy/mm/dd hh:dd:ss
devicename ONLINE
yyyy/mm/dd hh:dd:ss
VO1: Virt Out 1- 0
VI4: Virt In 4- 1
DI3: Direct In 3- 0
RI2: Remote In 2- 1
H5a: Contact In 1- 1
H1: Contact Output 1- 0
Data is only appended to the CSV file. The format for the data is as follows:
yyyy/mm/dd hh:dd:ss, devicename, offline
yyyy/mm/dd hh:dd:ss, devicename, ONLINE
yyyy/mm/dd hh:dd:ss, VO1: Virt Out 1, 0
yyyy/mm/dd hh:dd:ss, VI4: Virt In 4, 1
yyyy/mm/dd hh:dd:ss, DI3: Direct In 3, 0
yyyy/mm/dd hh:dd:ss, RI2: Remote In 2, 1
yyyy/mm/dd hh:dd:ss, H5a: Contact In 1, 1
yyyy/mm/dd hh:dd:ss, H1: Contact Output 1, 0
Options display for filtering, such as recording timing for Virtual Inputs and Outputs, but not Communications Status.
4.4.6.4 COMTRADE waveforms

Waveform files are viewable in the EnerVista software. The preferences are unrelated to Engineer and are outlined in the
UR Family Communications Guide.

4.4.7 Toolbars
These are toggled in the View > Toolbar menu.
The UR symbols are displayed for the toolbox icons. They change when the default setting is changed to IEC or ISO
symbols. The symbols displayed in the toolbox also vary by firmware version, reflecting what is supported for each release.
4.4.7.1 FlexLogic Editor toolbar
New Device Create a new settings file
Open File Open an existing settings file in the URS, CID, or IID format
Save FlexLogic Save the Logic Designer diagram
PDF Report Create a PDF document from Logic Designer diagram(s). Settings can be
changed under File > Preferences > Workbook Setup.
Toggle Compile Window Display or hide the compile window area
4
Sort Order Select to change the sort order of the Virtual Output list to the right of the
icon. Virtual Outputs can be sorted numerically in ascending and
descending order based on numbers and names.
Select VO to View (x - x) Select a Virtual Output to locate and select it in the workbook. Each Virtual
Output listed also contains the name of the sheet where the Virtual Output
is located.
Edit Mode Switch to Logic Designer mode
Logic Designer
Monitor Mode Switch to Logic Monitor mode
Logic Monitor
Turn On ALL Communications Turn on all communications to all Logic Designer diagrams that are in the
monitoring mode. Default upon each launch of Engineer.
Turn Off All Communications Turn off all communications to all Logic Designer diagrams that are in the
monitoring mode. This is a legacy function for serial communication to turn
off communication to devices. Turning off communication applies to the
current session only. When you re-launch the EnerVista software,
communication is on by default.
4.4.7.2 Token Toolbox
Drawing Tools
Draw a line. Click and drag to draw.
Draw multiple joined lines. Click and drag for each line. Double-click to finish.

Draw multi-sided object. Click for each line. Double-click to finish.
Draw four-sided object. Click and drag to draw.
Draw multiple curves. Click for each line. Double-click to finish.
Draw multiple, closed curves. Click for each line. Double-click to finish.
Draw oval or circle. Click and drag to draw.
Add text box with rectangle around it. Click to add. Double-click it to change text.
4
Add figure. Select file in the window that opens, then click on diagram canvas to add figure.
Add note icon and text. Click to add. Double-click to edit the title and text.
I/O Tokens
These are parts used in FlexLogic equations. They are the inputs and outputs of the Virtual Output equations. The display
can vary from that shown here.
Input symbol that can be configured to any FlexLogic operand value
Remote inputs from other devices
Input from another UR device. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and
cannot be used simultaneously.
Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously.

FlexAnalog symbol that can be used as the input to a FlexElement or use the FlexAnalog symbol to monitor an actual
value when in logic Monitoring mode
Contact Input Gate is similar to the Input symbol but is restricted to the operands associated with a Contact Input
Contact Output Gate is similar to the Input symbol but is restricted to the operands associated with a Contact Output.
The Operate and Seal-In settings can be configured graphically.
The Non-Volatile Latch is similar to the Input symbol but is restricted to the operands associated with a Non-Volatile
Latch. The Set and Reset settings can be configured graphically.
The final output of an equation is a numbered register called a virtual output. Virtual outputs can be used as an input
operand in any equation, including the equation that generates the output, as a seal-in or other type of feedback.
4
Place and configure a Remote Output. The UR's order code and firmware version then determine the availability of the
Remote Output.
Place and configure a Direct Output. The UR's order code and firmware version then determine the availability of the
Direct Output to another UR device.
Place and configure a Teleprotection Output. The UR's order code and firmware version then determine the availability
of the Teleprotection Output.
Place a User Programmable LED in the Logic Designer diagram. Not applicable when using a graphical front panel.
A Tag Out can be used in 1 of 2 ways. The first use of the Tag Out is to break up logic that needs to span several sheets.
The second use of the Tag Out is to associate a frequently used block of code with the Tag Out and then repeatedly use
the same block of code using a Tag In. When a Tag Out is referenced more than once, the Tag Out is replaced with a
Virtual Output during the compile phase.
Tag-In can is used to reference an existing Tag-Out. It joins another diagram to a previous diagram.
Boolean Tokens
These symbols are used to create FlexLogic Equations. Use them as intermediate logic for the Virtual Output equations.
The display can vary from that shown here.

Place an OR gate in the Logic Designer diagram. Only one action needs to occur. Any function input on the left side
satisfies the condition.
The number of inputs is configurable from two to 16.
Place an AND gate in the Logic Designer diagram. Multiple actions need to occur. All functions input on the left side are
required to satisfy the condition.
Place a NOR gate in the Logic Designer diagram. Gives the value of one when all input operands have a value of zero
and otherwise gives a value of zero. It gives an output signal when there are no input signals. An inverter that reverses
the logic state.
Place a NAND gate in the Logic Designer diagram. Gives the value of zero when all input operands have a value of one
and otherwise gives a value of one. It gives an output signal until all signals are present on its inputs. An inverter that
reverses the logic state.
Place a XOR gate in the Logic Designer diagram, which is two exclusive OR gates. Only one action needs to occur. If
there are two inputs or there is no input, there is no output.
Place a NOT gate in the Logic Designer diagram. Gives the value of one when the input operand has a value of zero and
4 otherwise gives a value of zero. It gives an output signal when there is no input signal. An inverter that reverses the
logic state.
Place a latch in the Logic Designer diagram. A latch has two inputs and one output. One input is the Set input, and
other input is the Reset input.
Place a positive one shot symbol that responds to a positive going edge in the Logic Designer diagram. A "one shot" is a
single input gate that generates a pulse ins response to an edge on the input.
Place a negative one shot symbol that responds to a negative going edge in the Logic Designer diagram
Place a positive one shot and a negative one shot symbol in the Logic Designer diagram
Place a timer in the Logic Designer diagram
Elements
These blocks configure properties of the element or use element operands as input to FlexLogic equations.

Place and configure a FlexElement. A FlexElement is a universal comparator used to monitor any analog actual value
calculated by the relay or a net difference of any two analog actual values of the same type.
Place and configure the Settings Group settings
Place and configure a Selector Switch element. Firmware version determines feature availability. The Selector Switch
element is intended to replace a mechanical selector switch. Typical applications include setting group
control or control of multiple logic sub-circuits in user-programmable logic. The element provides for two control inputs.
Place and configure a Digital Element. A Digital Element can monitor any FlexLogic operand
and present a target message and/or enable events recording depending on the output operand state.
Place and configure a Digital Counter element. A Digital Counter counts the number of state transitions
from Logic 0 to Logic 1. The counter is used to count operations such as the pickups of an element.
4
4.4.7.3 Basic Actions toolbar
Select Select components. Click one component and hold down the CTRL key to select others.
Or click and drag an area that contains multiple components to select.
Edit Vertices Shows vertices points for the component selected (if the component support vertices
manipulation)
Properties Shows the properties of the selected component
Zoom Normal Zoom in and center the screen to the spot selected
Zoom to Fit Zoom in to a magnitude that fits your entire schema layout on your entire screen
Zoom Custom Zoom in on the components that you have selected
Pan Move the viewable area of your screen around the schema. To activate, select this tool
and then place the hand icon over and part of your schema. Click and drag the hand in
a direction to move around the schema.
Align Top, Middle, Bottom Align the selected components to the top, middle, or bottom of the reference
component
Align Left, Center, Right Align the selected components to the left, middle, or right of the reference component
Space Across Evenly space the selected components across a horizontal axis, starting from the far
left component and ending at the far right component
Space Down Evenly space the selected components across a vertical axis, starting from the top
component and ending at the bottom component
Same Width Set the width of the selected components to the same width as the reference
component
Same Height Set the height of the selected components to the same height as the reference
component

Same Size Set the width and height of the selected components to the same width and height of
the reference component
4.4.7.4 Advanced Actions toolbar
Only basic objects (lines, rectangles, ellipses) can be rotated and flipped.
Only objects from the Drawing Toolbar can be structured (grouped, ungrouped, forward, backward).
Nudge Up, Down, Left, Right Moves selected component one pixel upward, downward, left, right
Rotate Rotates selected component freely. Once selected, put your mouse cursor over the
component and move the component clockwise or counter-clockwise depending on
what you need.
Rotate Left, Right Rotates selected component 90 degrees counter-clockwise or clockwise
Flip Vertical Flips the selected component on the vertical axis
4 Flip Horizontal Flips the selected component on the horizontal axis
Group, Ungroup Combines all selected components into one combined entity. Ungroups them into
separate components.
Front, Back Moves current components to the absolute front or back of all viewable layers
Forward, Backward Moves current components on layer higher or lower than its original layer hierarchy

Chapter 5: Settings
Settings
This chapter outlines front panel and/or software settings. The relay is not taken out of service when saving settings; the
relay is taken out of service when a settings file is written to it.
Settings can be viewed remotely in a web browser by entering the IP address of the relay, accessing the Device
Information Menu option, then the Front-Panel Display Report option.
When indicated that a restart is required for a setting change to take effect, use the Maintenance > Reboot Relay
Command in the software.
Settings file conversion from previous firmware versions is supported. See the Maintenance chapter.
5.1 Settings menu
 SETTINGS  B90 FUNCTION See page 5-5

 PRODUCT SETUP  
 SECURITY See page 5-5

  
 DISPLAY See page 5-23

  PROPERTIES
 GRAPHICAL FRONT PANEL Access in EnerVista

  See page 5-25
 CLEAR RELAY See page 5-36

  RECORDS
 COMMUNICATIONS See page 5-37

 
 MODBUS USER MAP See page 5-100

 
 REAL TIME See page 5-100

  CLOCK
 USER-PROGRAMMABLE See page 5-106

  FAULT REPORT

SETTINGS MENU CHAPTER 5: SETTINGS
 OSCILLOGRAPHY See page 5-106

 

  LEDS

  SELF TESTS
 CONTROL See page 5-114

  PUSHBUTTONS

  PUSHBUTTONS
 FLEX STATE See page 5-121

  PARAMETERS
 USER-DEFINABLE See page 5-122

  DISPLAYS
 DIRECT I/O See page 5-124

 
 INSTALLATION See page 5-130

  
 SETTINGS  AC INPUTS See page 5-131

 SYSTEM SETUP  
 POWER SYSTEM See page 5-131

  
5   FLEXCURVES

See page 5-132
 BUS See page 5-139

  
 SETTINGS  FLEXLOGIC See page 5-155

 FLEXLOGIC   EQUATION EDITOR
 FLEXLOGIC See page 5-155

   TIMERS
 NON-VOLATILE See page 5-155

   LATCHES
 SETTINGS  SETTING GROUP 1 See page 5-156

 GROUPED ELEMENTS  
 SETTING GROUP 2
  
 SETTING GROUP 3
 
 SETTING GROUP 4
 
 SETTING GROUP 5
 
 SETTING GROUP 6
  
 SETTINGS  TRIP BUS See page 5-181

 CONTROL ELEMENTS  
 SETTING GROUPS See page 5-183

  

CHAPTER 5: SETTINGS OVERVIEW
 DIGITAL ELEMENTS See page 5-184

 
 MONITORING See page 5-187

   ELEMENTS
 SETTINGS  CONTACT INPUTS See page 5-192

 INPUTS / OUTPUTS  
 VIRTUAL INPUTS See page 5-194

  
 CONTACT OUTPUTS See page 5-195

 
 VIRTUAL OUTPUTS See page 5-199

 
 RESETTING See page 5-199

 
 DIRECT INPUTS See page 5-200

 
 DIRECT OUTPUTS See page 5-200

  
 SETTINGS TEST MODE See page 5-204

 TESTING  FUNCTION: Disabled
TEST MODE FORCING: See page 5-205

  On
  FORCE CONTACT
 INPUTS
See page 5-205 5
 FORCE CONTACT See page 5-206
   OUTPUTS
 SETTINGS  GOOSE See page 5-207

 SIMULATION  
5.2 Overview
5.2.1 Introduction to elements
For URs, the term element is used to describe a feature that is based around a comparator. The comparator is provided
with an input (or set of inputs) that is tested against a programmed setting (or group of settings) to determine if the input is
within the defined range that sets the output to logic 1, also referred to as setting the flag. A single comparator can make
multiple tests and provide multiple outputs. For example, the time overcurrent comparator sets a pickup flag when the
current input is above the setting and sets an operate flag when the input current has been at a level above the pickup
setting for the time specified by the time-current curve settings. All comparators use analog actual values as the input.
An exception to this rule is digital elements, which use logic states as inputs.
Elements are arranged into two classes, grouped and control. Each element classed as a grouped element is provided with
six alternate sets of settings, in setting groups numbered 1 through 6. The performance of a grouped element is defined by
the setting group that is active at a given time. The performance of a control element is independent of the selected active
setting group.

OVERVIEW CHAPTER 5: SETTINGS
The main characteristics of an element are shown on a logic diagram. This includes the inputs, settings, fixed logic, and the
output operands generated. The previous chapter explains how to read a logic diagram, and the abbreviations used in a
diagram are defined in the Abbreviations chapter.
Some settings are specified in per-unit (pu) calculated quantities:
pu quantity = (actual quantity) / (base quantity)
Where the current source is from a single current transformer (CT), the base quantity is the nominal secondary or primary
current of the CT. Use the secondary current base to convert per-unit settings to/from a secondary current value, and use
the primary current base to convert to/from a primary current value.
For voltage elements, the primary base quantity is the nominal phase-to-phase primary voltage of the protected system
provided that the VT ratio setting is set to the nominal ratio of the VTs and the secondary voltage setting is set to the
phase-to-phase voltage seen by the relay when the voltage of the protected system in nominal. The UR uses the
convention that nominal voltages in a three-phase system are phase-to-phase voltages.
For example, on a system with a 13.8 kV nominal primary voltage, the base quantity is 13800 V. With 14400:120 V delta-
connected VTs, the secondary base quantity and secondary voltage setting is:
Eq. 5-1
For wye-connected VTs, the primary and secondary base quantities are as before, but the secondary voltage setting (here
a phase-to-ground value) is:
Eq. 5-2
5 Some settings are common to many elements, outlined as follows:

• FUNCTION setting — This setting programs the element to operate when selected as “Enabled.” The factory default is
“Disabled.” Once “Enabled,” any element associated with the function becomes active and all options become
available.
• NAME setting — This setting is used to uniquely identify the element.
• PICKUP setting — For simple elements, this setting is used to program the level of the measured parameter above or
below which the pickup state is established. In more complex elements, a set of settings can be provided to define the
range of the measured parameters that cause the element to pick up.
• PICKUP DELAY setting — This setting sets a time-delay-on-pickup, or on-delay, for the duration between the pickup
and operate output states.
• RESET DELAY setting — This setting is used to set a time-delay-on-dropout, or off-delay, for the duration between the
operate output state and the return to logic 0 after the input transits outside the defined pickup range.
• BLOCK setting — The default output operand state of all comparators is a logic 0 or “flag not set.” The comparator
remains in this default state until a logic 1 is asserted at the RUN input, allowing the test to be performed. If the RUN
input changes to logic 0 at any time, the comparator returns to the default state. The RUN input is used to supervise
the comparator. The BLOCK input is used as one of the inputs to RUN control.
• TARGET setting — This setting is used to define the operation of an element target message. When set to "Disabled,"
no target message or illumination of a front panel LED indicator is issued upon operation of the element. When set to
“Self-Reset,” the target message and LED indication follow the operate state of the element and self-resets once the
operate element condition clears. When set to “Latched,” the target message and LED indication remains visible after
the element output returns to logic 0 until a RESET command is received by the relay.
• EVENTS setting — This setting is used to control whether the pickup, dropout, or operate states are recorded by the
event recorder. When set to “Disabled,” element pickup, dropout, or operate are not recorded as events. When set to
“Enabled,” events are created for
<Element> PKP (pickup)
<Element> DPO (dropout)
<Element> OP (operate)

CHAPTER 5: SETTINGS PRODUCT SETUP
The DPO event is created when the measure and decide comparator output transits from the pickup state (logic 1) to
the dropout state (logic 0). This can happen when the element is in the operate state if the reset delay time is not zero.
Not every operand of a given element in a UR relay generates events, only the major output operands. Elements,
asserting output per phase, log operating phase output only, without asserting the common three-phase operand
event.
5.3 Product setup

5.3.1 B90 function
SETTINGS  PRODUCT SETUP  B90 FUNCTION
 UR FUNCTION B90 FUNCTION: Range: Protection, Logic
  Protection
The setting acts as a B90 master switch enabling certain relay elements. The features displayed vary with the selection of
"Protection" or "Logic." All features dependent on AC inputs (such as system setup, bus differential, instantaneous
overcurrent, time overcurrent, end fault protection, CT Trouble, AC metering, and undervoltage) become available if the
B90 FUNCTION is set to “Protection.” Features that are not dependent on AC signals (such as logic part of the Breaker Failure
protection or Isolator Monitoring) become available if the B90 FUNCTION is set to “Logic.”
Typically, three IEDs in the B90 system have hardware configured to support AC inputs (set B90 FUNCTION to “Protection”),
while the fourth IED is configured to support all required input contacts and is intended for isolator monitoring and other
logic functions (set B90 FUNCTION to “Logic”).
The B90 FUNCTION setting allows the user to work with a single setting file, program all required functions (both protection
and logic), download the same file to all the B90 IEDs, and modify the settings accordingly to finalize the application. This
5
means that some modules, for example CT/VT module when set to "Logic," can become unusable. Communications and
B90 FUNCTION settings are typically modified when downloading the common B90 setting file.
If hardware modules do not match the B90 order code, the minor self-test error "Discrepancy between order code and
h/w" displays. The B90 remains in service, and features are available as per detected hardware. If, for example, the B90
order code assumes 24 feeder configuration, but there are two DSP modules with 16 CT inputs, the B90 configuration
allows 16 current terminals in the SETTINGS  SYSTEM SETUP  AC INPUTS  CURRENT TERMINAL F1(S8) menu.
5.3.2 Security
5.3.2.1 Security overview

The following security features are available:
• Password security — Basic security present by default
• EnerVista security — Role-based access to various EnerVista software screens and configuration elements. The
feature is present by default in the EnerVista software.
• CyberSentry security — Advanced security available using a software option. When purchased, the option is enabled
automatically, and the default Password security and EnerVista security are disabled.
Lost password
If all passwords are lost, recovery is possible by resetting the unit to default values. Note that the relay is reset to default
values, not just the passwords.
To reset the unit after a lost password:
1. Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email
account. Customer service provides a code to reset the relay to the factory defaults.
2. Enter the reset code on the front panel, under COMMANDS  RELAY MAINTENANCE  SERVICE COMMAND.

PRODUCT SETUP CHAPTER 5: SETTINGS
3. Change the default password of ChangeMe1# as outlined in the Set Up CyberSentry and Change Default Password
section at the end of the Installation chapter.
Password requirements
A user account requires an alpha-numeric password that meets the following requirements:
• Password is case-sensitive
• Password cannot contain the user account name or parts of the user account that exceed two consecutive
characters
• Password must be 8 to 20 characters in length
• Password must contain characters from all of the following categories:
– English uppercase characters (A through Z)
– English lowercase characters (a through z)
– Base 10 digits (0 through 9)
– Non-alphabetic characters (for example, ~, !, @, #, $,%, &)
5.3.2.2 Password security

SETTINGS  PRODUCT SETUP  SECURITY
 SECURITY ACCESS LEVEL: Range: Restricted, Command, Setting,
  Restricted Factory Service (for factory use only)
 CHANGE LOCAL See page 5-7

  PASSWORDS
5   CHANGE REMOTE
 PASSWORDS
See page 5-8
 ACCESS See page 5-8

  SUPERVISION
 DUAL PERMISSION See page 5-9

  SECURITY ACCESS
PASSWORD ACCESS Range: Disabled, Enabled

 EVENTS: Disabled
The B90 supports password entry from a local or remote connection.

Local access is defined as access to settings or commands via the front panel. This includes both keypad entry and the
RS232 port. Remote access is defined as access to settings or commands via any rear communications port. This includes
both Ethernet and RS485 connections. Any change to the local or remote password enables this functionality.
ACCESS LEVEL — The "Restricted" option means that settings and commands can be accessed, but there is no access to
factory configuration. Access automatically reverts to the Restricted level according to the access level timeout setting
values. The access level is set to Restricted when control power is cycled.
The "Factory Service" level is not available and intended for factory use only.
There are two user security access levels, setting and command, for which you can set a password for each. Use of a
password for each level controls whether users can enter commands or change settings. Another option is to specify
setting and/or command access for individual user accounts.
• Setting — Allows the user to make any changes to any of the setting values:
– Changing any setting
– Test mode operation
• Command — Restricts the user from making any settings changes, but allows the user to perform the following
operations:
– Changing the state of virtual inputs
– Clearing the event records

– Clearing the oscillography records

– Changing the date and time
– Clearing the data logger
– Clearing the user-programmable pushbutton states
corresponding connection password. If the connection is to the back of the B90, the remote password must be used. If the
connection is to the RS232 port of the front panel, the local password must be used.
The local setting and command sessions are initiated by the user through the front panel display and are disabled either by
the user or by timeout (via the setting and command level access timeout settings). The remote setting and command
sessions are initiated by the user through the EnerVista software and are disabled either by the user or by timeout.
The state of the session (local or remote, setting or command) determines the state of the following FlexLogic operands:
• ACCESS LOC SETG OFF — Asserted when local setting access is disabled
• ACCESS LOC SETG ON — Asserted when local setting access is enabled
• ACCESS LOC CMND OFF — Asserted when local command access is disabled
• ACCESS LOC CMND ON — Asserted when local command access is enabled
• ACCESS REM SETG OFF — Asserted when remote setting access is disabled
• ACCESS REM SETG ON — Asserted when remote setting access is enabled
• ACCESS REM CMND OFF — Asserted when remote command access is disabled
• ACCESS REM CMND ON — Asserted when remote command access is enabled
A command or setting write operation is required to update the state of the remote and local security operands
listed.
When a setting password or command password is set or updated, user access with a graphical front panel is
5
removed. Simply log in again on the graphical front panel.
When the setting password is set or updated, the graphical front panel Access Level displays as Command. This is
because the graphical front panel is a Modbus client and it does not have automatic access to the password
change.
PASSWORD ACCESS EVENTS — This setting allows recording of password access events in the event recorder.
Change local passwords

SETTINGS  PRODUCT SETUP  SECURITY  CHANGE LOCAL PASSWORDS
 CHANGE LOCAL CHANGE SETTING Range: No, Yes
 PASSWORDS  PASSWORD: No
CHANGE COMMAND Range: No, Yes

 PASSWORD: No
As outlined in the previous section, there are two user security access levels, setting and command. Use of a password for
each level controls whether users can enter commands or change settings.
Proper password codes are required to enable each access level. When a CHANGE COMMAND PASSWORD or CHANGE
SETTING PASSWORD setting is programmed to “Yes” via the front panel interface, the following message sequence is
invoked:
1. ENTER NEW PASSWORD: ____________.
2. VERIFY NEW PASSWORD: ____________.
3. NEW PASSWORD HAS BEEN STORED.
To gain write access to a “Restricted” setting, program the ACCESS LEVEL setting in the main security menu to “Setting” and
then change the setting, or attempt to change the setting and follow the prompt to enter the programmed password. If the
password is correctly entered, access is allowed. Access automatically reverts to the “Restricted” level according to the
access level timeout setting values and when power is cycled.

If the setting and command passwords are identical, then this one password allows access to both commands and
settings.
If a remote connection is established, local passcodes are not visible.
Change remote passwords

Proper passwords are required to enable each command or setting level access, which are explained in the previous
section.
SETTINGS  PRODUCT SETUP  SECURITY  CHANGE REMOTE PASSWORDS
 CHANGE REMOTE CHANGE SETTING Range: No, Yes
 PASSWORDS  PASSWORD: No
CHANGE COMMAND Range: No, Yes

 PASSWORD: No
To set the command or setting password in EnerVista:

1. In the EnerVista software or from the front panel, navigate to Settings > Product Setup > Security menu item to open
the remote password settings window.
2. Click the command or setting password Change button.
3. Enter the new password in the New Password field. Requirements are outlined in the Password Requirements section
earlier in this chapter. When an original password has already been used, enter it in the Enter Password field and click
the Send Password to Device button.
4. Re-enter the password in the Confirm Password field.
5 5. Click the OK button. The password is checked to ensure that it meets requirements.
If you establish a local (serial) connection to the relay, you cannot view remote passcodes.
Access supervision
SETTINGS  PRODUCT SETUP  SECURITY  ACCESS SUPERVISION
 ACCESS  ACCESS LEVEL See below
 SUPERVISION   TIMEOUTS
INVALID ATTEMPTS Range: 2 to 5 in steps of 1

 BEFORE LOCKOUT: 3
PASSWORD LOCKOUT Range: 5 to 60 minutes in steps of 1

 DURATION: 5 min
The following access supervision settings are available.

INVALID ATTEMPTS BEFORE LOCKOUT — This setting specifies the number of times that an incorrect password can be entered
within a three-minute time span before lockout occurs. When lockout occurs, the LOCAL ACCESS DENIED or REMOTE ACCESS
DENIED FlexLogic operands are set to “On.” These operands are returned to the “Off” state upon expiration of the lockout.
PASSWORD LOCKOUT DURATION — This setting specifies the time that the B90 locks out password access after the number
of invalid password entries specified by the INVALID ATTEMPTS BEFORE LOCKOUT setting has occurred.
The B90 provides a means to raise an alarm upon failed password entry. If password verification fails while accessing a
password-protected level of the relay (either settings or commands), the UNAUTHORIZED ACCESS FlexLogic operand is
asserted. The operand can be programmed to raise an alarm via contact outputs or communications. This feature can be
used to protect against both unauthorized and accidental access attempts.
The UNAUTHORIZED ACCESS operand is reset with the COMMANDS  CLEAR RECORDS  RESET UNAUTHORIZED ALARMS
command. Therefore, to apply this feature with security, password-protect the Command level. The operand does not
generate events or targets.
If events or targets are required, the UNAUTHORIZED ACCESS operand can be assigned to a digital element programmed with
event logs or targets enabled.
The following table outlines access level timeout settings.
SETTINGS  PRODUCT SETUP  SECURITY  ACCESS SUPERVISION  ACCESS LEVEL TIMEOUTS
 ACCESS LEVEL COMMAND LEVEL ACCESS Range: 5 to 480 minutes in steps of 1
 TIMEOUTS  TIMEOUT: 5 min
SETTING LEVEL ACCESS Range: 5 to 480 minutes in steps of 1

 TIMEOUT: 30 min
These settings allow the user to specify the length of inactivity required before returning to the Restricted access level.
Note that the access level is set to Restricted when control power is cycled.
COMMAND LEVEL ACCESS TIMEOUT — This setting specifies the length of inactivity (no local or remote access) required to 5
return to Restricted access from the Command password level.
SETTING LEVEL ACCESS TIMEOUT — This setting specifies the length of inactivity (no local or remote access) required to return
to Restricted access from the Command password level.
Dual-permission security access

SETTINGS  PRODUCT SETUP  SECURITY  DUAL PERMISSION SECURITY ACCESS
 DUAL PERMISSION LOCAL SETTING AUTH: Range: selected FlexLogic operands (see below)
 SECURITY ACCESS  On
REMOTE SETTING AUTH: Range: FlexLogic operand

 On
ACCESS AUTH Range: 5 to 480 minutes in steps of 1

 TIMEOUT: 30 min
This feature provides a mechanism to prevent unauthorized or unintended upload of settings to a relay through the local
or remote interface.
The following settings are available through the local (front panel) interface only.
• LOCAL SETTING AUTH — This setting is used for local (front panel or RS232 interface) setting access supervision. Valid
values for the FlexLogic operands are either “On” (default) or any physical “Contact Input ~~ On” value.
If this setting is “On,“ then local setting access functions as normal; that is, a local setting password is required. If this
setting is any contact input on FlexLogic operand, then the operand must be asserted (on) prior to providing the local
setting password to gain setting access.
If setting access is not authorized for local operation (front panel or RS232 interface) and the user attempts to obtain
setting access, then the UNAUTHORIZED ACCESS message displays on the front panel.
If this setting is "Off," firmware upgrades are blocked. If this setting is "On," firmware upgrades are allowed.
• REMOTE SETTING AUTH — This setting is used for remote (Ethernet or RS485 interface) setting access supervision.

If this setting is “On” (the default setting), then remote setting access functions as normal; that is, a remote password is
required. If this setting is “Off,” then remote setting access is blocked even if the correct remote setting password is
provided. If this setting is any other FlexLogic operand, then the operand must be asserted (set as on) prior to
providing the remote setting password to gain setting access.
If this setting is "Off," firmware upgrades are blocked. If this setting is "On," firmware upgrades are allowed.
• ACCESS AUTH TIMEOUT — This setting represents the timeout delay for local setting access. This setting is applicable
when the LOCAL SETTING AUTH setting is programmed to any operand except “On.” The state of the FlexLogic operand
is monitored continuously for an off-to-on transition. When this occurs, local access is permitted and the timer
programmed with the ACCESS AUTH TIMEOUT setting value is started. When this timer expires, local setting access is
immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the
timeout is restarted. The status of this timer updates every five seconds.
The following settings are available through the remote (EnerVista UR Setup) interface only. Select the Settings > Product
Setup > Security menu item to display the security settings window.
The Remote Settings Authorized setting is used for remote (Ethernet or RS485 interface) setting access supervision. If this
setting is “On” (the default setting), then remote setting access functions as normal; that is, a remote password is required.
If this setting is “Off,” then remote setting access is blocked even if the correct remote setting password is provided. If this
setting is any other FlexLogic operand, then the operand must be asserted (on) prior to providing the remote setting
password to gain setting access.
The Access Authorized Timeout setting represents the timeout delay remote setting access. It applies when the Remote
Settings Authorized setting is programmed to any operand except “On” or “Off.” The state of the FlexLogic operand is
continuously monitored for an off-to-on transition. When this occurs, remote setting access is permitted, and the timer
programmed with the Access Authorized Timeout setting value is started. When this timer expires, remote setting access
is denied immediately. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout
is restarted. The status of this timer updates every five seconds.
5.3.2.3 EnerVista security
Enable the security management system

The EnerVista security system allows an administrator to manage access privileges of multiple users of EnerVista.
It is disabled by default to allow access to the device immediately after installation. When security is disabled, all users
have administrator access. GE recommends enabling the EnerVista security before placing the device in service.

To enable the security system and require password use:

1. Select the Security > User Management menu to open the user management window.
2. Enable the Enable Security check box in the lower-left corner to enable the security management system.
3. Click the Ok button.
If you force password entry by using this feature, ensure that you know the Administrator password. If you do not
know the password and are locked out of the software, contact GE Grid Solutions for the default password of a UR
5
device. When using CyberSentry, the default password is "ChangeMe1#".
Security is now enabled for the EnerVista UR Setup software. Upon starting the software, users are now required to enter a
username and password.
Add a new user

The following pre-requisites are required to add user accounts to the EnerVista security management system:
• The user adding the account must have administrator rights
• The EnerVista security management system must be enabled (previous section)
To add a user account:
1. Select the Security > User Management item from the top menu to open the user management window.
2. Enter a username in the User field. The username must be four to 20 characters in length.

3. Select the user access rights by enabling the check box of one or more fields.
The table outlines access rights.

Table 5-1: Access rights summary
Field Description
Delete Entry Deletes the user account when exiting the user management window
5 Actual Values Allows the user to read Actual Values
Settings Allows the user to read Settings values
Commands Allows the user to execute Commands
Event Recorder Allows the user to use the Event Recorder
FlexLogic Allows the user to read FlexLogic values
Update Info Allows the user to write to any function to which they have read privileges. When any of the Settings, Event
Recorder, and FlexLogic check boxes are enabled by themselves, the user is granted read access. When
any of them are enabled in conjunction with the Update Info box, they are granted read and write access.
The user is not granted write access to functions that are not enabled, even if the Update Info field is
enabled.
Admin When the check box is enabled, the user becomes an EnerVista UR Setup administrator and has all
administrative rights. Exercise caution when granting administrator rights.
4. Click OK to add the user account to the system.
Modify user privileges

The following pre-requisites are required to modify user privileges in the EnerVista security management system:
• The user modifying the privileges must have administrator rights
• The EnerVista security management system must be enabled (the Enable Security check box enabled)
To modify user privileges:
1. Select the Security > User Management item from the top menu to open the user management window.
2. Locate the username in the User field.

3. Modify the user access rights by enabling or disabling one or more of the check boxes.
The table outlines access rights.

Table 5-2: Access rights summary
Field Description
Delete Entry Deletes the user account when exiting the user management window
Actual Values Allows the user to read actual values 5
Settings Allows the user to read setting values
Commands Allows the user to execute commands
Event Recorder Allows the user to use the digital fault recorder
FlexLogic Allows the user to read FlexLogic values
Update Info Allows the user to write to any function to which they have read privileges. When any of the Settings, Event
Recorder, and FlexLogic check boxes are enabled by themselves, the user is granted read access. When
any of them are enabled in conjunction with the Update Info box, they are granted read and write access.
The user is not granted write access to functions that are not enabled, even if the Update Info field is
enabled.
Admin When this check box is enabled, the user becomes an EnerVista UR Setup administrator and has all
administrative rights. Exercise caution when granting administrator rights.
4. Click OK to save the changes.
5.3.2.4 CyberSentry security
This feature requires a CyberSentry software option. See the Order Codes section in chapter 2 for details.
The EnerVista software provides the means to configure and authenticate the B90 access using either a server or the
device. Access to functions depends on user role.
The login screen of EnerVista has two options for access to the B90, these being Server and Device authentication.

Figure 5-1: Login screen for CyberSentry
When the "Server" Authentication Type is selected, the B90 uses the RADIUS server and not its local authentication
database to authenticate the user.
When the "Device" button is selected, the B90 uses its local authentication database and not the RADIUS server to
authenticate the user. In this case, it uses built-in roles (Administrator, Engineer, Supervisor, Operator, Observer, or
Administrator and Supervisor when Device Authentication is disabled), as login accounts and the associated passwords
are stored on the B90 device. In this case, access is not user-attributable. In cases where user-attributable access is
required, especially for auditable processes for compliance reasons, use server authentication (RADIUS) only.
No password or security information is displayed in plain text by the EnerVista software or the UR device, nor are they ever
transmitted without cryptographic protection.
Only (TCP/UDP) ports and services that are needed for device configuration and for customer enabled features are
5 open. All the other ports are closed. For example, Modbus is on by default, so its TCP port 502, is open. But if
Modbus is disabled, port 502 is closed. This function has been tested and no unused ports have been found open.
When CyberSentry is enabled, Modbus communications over Ethernet is encrypted, which is not always tolerated by
SCADA systems. The UR has a bypass access feature for such situations, which allows unencrypted Modbus over Ethernet.
The Bypass Access setting is available on the SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY screen. Note that
other protocols (DNP, 101, 103, 104, EGD) are not encrypted, and they are good communications options for SCADA
systems when CyberSentry is enabled.
When using the rear RS485 port and CyberSentry, registers can be read with a maximum buffer of 64 bytes. Settings may
not be written, so use another port or configure the SERIAL INACTIVITY TIMEOUT setting to a high value, such as eight
minutes, to give the relay enough time to finish the task.
CyberSentry settings through EnerVista

CyberSentry security settings are configured under Device > Settings > Product Setup > Security.

Figure 5-2: Security panel when CyberSentry installed
For the Device > Settings > Product Setup > Supervisory option, the panel looks like the following.
Figure 5-3: Supervisory panel
5
For the Security panel, the following settings are available.

Table 5-3: RADIUS server settings

Setting name Description Minimum Maximum Default Units Minimum
permission
Primary RADIUS IP IP address of the main RADIUS server. 0.0.0.0 223.255.255.254 0.0.0.0 - Administrator
Address Default value indicates no Primary
RADIUS server is configured, and hence
RADIUS is disabled.
Restart the relay for any change to take
effect.
Primary RADIUS authentication port 1 65535 1812 - Administrator
Authentication Port
Primary Accounting RADIUS accounting port 1 65535 1813 - Administrator
Port
Vendor ID An identifier that specifies RADIUS Value that Administrator
vendor-specific attributes used with the represents
protocol General
Electric
RADIUS Authentication method used by RADIUS EAP-TTLS PAP EAP-TTLS - Administrator
Authentication server. Can use EAP-TTLS, PEAP-GTC, or
Method PAP. Selecting the PEAP-GTC option
disables RADIUS authentication.
RADIUS Shared secret used in authentication. It See the See the following N/A - Administrator
Authentication displays as asterisks. This setting must Password password section
(Shared) Secret meet the CyberSentry password Requirements for requirements
requirements. section earlier
in this chapter
Timeout Timeout in seconds between re- 0 9999 10 sec Administrator
transmission requests
5 Retries Number of retries before giving up 0 9999 3 - Administrator
Confirm RADIUS Confirmation of the shared secret. The See the 245 characters N/A - Administrator
Authentication entry displays as asterisks. Password
(Shared) Secret Requirements
section
Table 5-4: General security settings

permission
Session Lockout Number of failed authentications before the 0 (lockout 99 3 - Administrator
device blocks subsequent authentication disabled)
attempts for the lockout period
Session Lockout The period in minutes that a user is prevented 0 (no period) 9999 3 min Administrator
Period from logging in after being locked out
Syslog Server IP The IP address of the target Syslog server to 0.0.0.0 223.255. 0.0.0.0 - Administrator
Address which all security events are transmitted 255.254
Syslog Server Port The UDP port number of the target syslog 1 65535 514 - Administrator
Number server to which all security events are
transmitted
Device When enabled, local Device authentication Disabled Enabled Enabled - Administrator
Authentication with roles is allowed. When disabled, the UR
only authenticates to the AAA server (RADIUS).
NOTE: Administrator and Supervisor (if still
enabled) remain active even after Device
authentication is disabled. The only permission
for local Administrator is to re-enable Device
authentication when Device authentication is
disabled. To re-enable Device authentication,
the Supervisor unlocks the device for setting
changes, and then the Administrator can re-
enable Device authentication.


permission
Firmware Lock Indicates if the device receives firmware Disabled Enabled Enabled - Administrator
(via Lock Relay) upgrades. If Enabled and the firmware
upgrade attempt is made, the device denies
the upgrade and displays an error message
that the lock is set. On each firmware upgrade,
this setting goes back to the default.
The Lock Relay setting blocks settings and

firmware updates.
Factory Service When enabled, the device can go into factory Disabled Enabled Disabled - Supervisor
Mode service mode. To enable, Supervisor (Administrator
authentication is necessary. when Supervisor
is disabled)
Restore to Defaults Sets the device to factory defaults No Yes No - Administrator
Supervisor Role When enabled, the Supervisor role is active. To Disabled Enabled Enabled - Administrator to
enable, Administrator authentication is enable and
necessary. When disabled, the Supervisor role Supervisor to
is inactive. To disable, Supervisor disable
authentication is necessary.
RADIUS user names Ensures that RADIUS user names are not the See RADIUS See - Administrator
same as local/device role names server RADIUS
documents server
document
s
Password Local/device roles except for Observer are See the See the Change Text The specified
password-protected. All RADIUS users are Password following Me1# role and
password-protected. Requirements password Administrator,
section earlier
in this chapter
section for
requireme
except for
Supervisor,
5
nts where it is only
itself
Table 5-5: Security alarm settings

Setting name Description / Details Min Max Default Units Minimum
permissions
Failed A threshold number indicating when an alarm 0 99 3 - Administrator
Authentications is set off to indicate too many failed (disabled)
authentication attempts
Firmware Lock A value indicating if the device can receive a Disabled Enabled Enabled - Administrator
firmware upgrade. If Enabled and a firmware
upgrade attempt is made, the device alarm
activates. If Disabled, the device alarm does not
activate. On each firmware upgrade this setting
goes back to the default.
Settings Lock A value indicating if the device can accept any Disabled Enabled Enabled - Supervisor
settings changes. If Enabled and a settings (Administrator if
change attempt is made, the device alarm Supervisor has
activates. If Disabled, the device alarm does not been disabled)
activate.
CyberSentry settings through the front panel

SETTINGS  PRODUCT SETUP  SECURITY
 SECURITY LOGIN: Range: Administrator, Engineer, Supervisor,
  None Operator, Factory (for factory use only), None
 CHANGE LOCAL See page 5-18

  PASSWORDS
 SESSION See page 5-19

  SETTINGS

 RESTORE DEFAULTS See page 5-19

 
 SUPERVISORY See page 5-19

 
SYSLOG IP ADDRESS: Range: 0.0.0.0, 255.255.255.255

 0.0.0.0
SYSLOG PORT NUMBER: Range: 1 to 65535

 514
LOGIN — This setting is applicable for Device authentication only. This setting allows a user to log in with a specific role, as
outlined here. For the Supervisor role, enable the “Supervisor Role” setting. Log out by right-clicking the device in EnerVista
and selecting the Disconnect option.
Whenever a new role is logged in, the user is prompted to enter a password. Passwords must obey the requirements
specified earlier in the chapter in the Password Requirements section.The UR device supports five roles. Roles have their
corresponding passwords, except the Observer role, which does not require a password. There are no time-outs for the
Administrator, Engineer, Operator, and Supervisor when logged in using the front panel; log out manually or use the
Command > Security commands in the software.
The roles are defined as follows:
• Administrator — Complete read/write access to all settings and commands. This role does not allow concurrent
access. This role has an operand to indicate when it is logged on.
• Engineer — Complete read/write access to all settings and commands except configuring Security settings and
firmware upgrades. This role does not allow concurrent access.
• Operator — The Operator has read/write access to all settings under the Commands menu/section. This role does not
5 •
exist offline.
Supervisor — This is only an approving role. This role’s authentication commits setting changes submitted by
Administrator or Engineer. The Supervisor role authenticates to unlock the UR relay for setting changes and not
approve changes after the fact. Only a Supervisor can set the Settings Lock and Firmware Lock in the Security
settings. This role also has the ability to forcefully log off any other role and clear the security event log. This role can
also be disabled, but only through a Supervisor authentication. When this role is disabled its permissions are assigned
to the Administrator role.
• Observer — This role has read-only access to all B90 settings. This role allows unlimited concurrent access but it has
no download access to any files on the device. Observer is the default role if no authentication has been done to the
device. This role displays as "None" on the front panel. When local authentication is used, no password is required for
this role. When RADIUS server authentication is used, a password is required.
The Factory service role is not available. It is for factory use only.
The Local Access Denied message on the front panel can mean that you need to log in to the UR in order to
complete the action.
Change local passwords

SETTINGS  PRODUCT SETUP  SECURITY  CHANGE LOCAL PASSWORDS
 CHANGE LOCAL LOGIN: Range: 20 alphanumeric characters
 PASSWORDS  None
NEW PASSWORD: Range: 20 alphanumeric characters


CONFIRM PASSWORD: Range: 20 alphanumeric characters

The menu is shown on the front panel upon successful login of the Administrator role.
The LOGIN setting in this menu is similar to that described in SETTINGS > PRODUCT SETUP > SECURITY except for the factory
role.

Passwords are stored in text format. No encryption is applied.
In Device authentication mode, the Observer role does not have a password associated with it. In Server
authentication mode the Observer role requires a password.
If you are locked out of the software, contact GE Grid Solutions for the default password. When using CyberSentry,
the default password is "ChangeMe1#".
Once the passwords are set, the Administrator with Supervisor approval can change the role-associated password.
In CyberSentry, password encryption is not supported.
Session settings
SETTINGS  PRODUCT SETUP  SECURITY  SESSION SETTINGS
 SESSION SESSION LOCKOUT: Range: 0 to 99
 SETTINGS  3
SESSION LOCKOUT Range: 0 to 9999 minutes

 PERIOD: 3 min
SESSION LOCKOUT — This setting specifies the number of failed authentications before the device blocks subsequent
authentication attempts for the lockout period. A value of zero means lockout is disabled.
SESSION LOCKOUT PERIOD — This setting specifies the period of time in minutes of a lockout period. A value of 0 means that
there is no lockout period.
Restore defaults
SETTINGS  PRODUCT SETUP  SECURITY  RESTORE DEFAULTS
5
 RESTORE DEFAULTS LOAD FACTORY Range: Yes, No
  DEFAULTS: No
LOAD FACTORY DEFAULTS — This setting is used to reset all the settings, communication, and security passwords. An
Administrator role is used to change this setting and a Supervisor role (if not disabled) approves it.
Supervisory
SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY
 SUPERVISORY DEVICE Range: Yes, No
  AUTHENTICATION: Yes
BYPASS ACCESS: Range: Local, Remote, Local and Remote, Disabled,

 Disabled Pushbuttons
LOCK RELAY: Range: Enabled, Disabled

 Disabled
FACTORY SERVICE Range: Enabled, Disabled

 MODE: Disabled
 SELF TESTS See below

 
SUPERVISOR ROLE: Range: Enabled, Disabled

 Disabled
SERIAL INACTIVITY Range: 1 to 9999 minutes

 TIMEOUT: 1 min
The Supervisory menu settings are available for Supervisor role only, or if the Supervisor role is disabled then for the
Administrator role only.

DEVICE AUTHENTICATION — This setting is enabled by default, meaning "Yes" is selected. When enabled, Device
authentication with roles is enabled. When this setting is disabled, the UR only authenticates to the AAA server (RADIUS).
However, the Administrator and Supervisor (when enabled) remain active even after device authentication is disabled and
their only permission is to re-enable Device authentication. To re-enable Device authentication, the Supervisor unlocks the
device for settings changes, then the Administrator re-enables device authentication.
BYPASS ACCESS — The bypass security feature provides an easier access, with no authentication and encryption for those
special situations when this is considered safe. Only the Supervisor, or the Administrator when the Supervisor role is
disabled, can enable this feature.
Mode Front panel or serial (RS232, RS485) Ethernet
Normal mode Authentication — Role Based Access Control (RBAC) Authentication — RBAC and passwords encrypted
and passwords in clear SSH tunneling
Bypass access mode No passwords for allowed RBAC levels No passwords for allowed RBAC levels
No SSH tunneling
The bypass options are as follows:

• Local — Bypasses authentication for push buttons, keypad, RS232, and RS485
• Remote — Bypasses authentication for Ethernet
• Local and Remote — Bypasses authentication for push buttons, keypad, RS232, RS485, and Ethernet
• Pushbuttons — Bypasses authentication for front panel push buttons only. On the graphical front panel, the
authentication for side pushbuttons to control breakers and disconnects also is bypassed.
LOCK RELAY — This setting uses a Boolean value (Enabled/Disabled) to indicate if the device accepts settings changes and
whether the device can receive a firmware upgrade. This setting can be changed by the Supervisor role, if it is enabled, or
by the Administrator if the Supervisor role is disabled. The Supervisor role disables this setting for the relay to start
5 accepting settings changes, command changes, or firmware upgrade. After all the setting changes are applied or
commands executed, the Supervisor enables to lock settings changes.
Example: If this setting is enabled and an attempt is made to change settings or upgrade the firmware, the UR device
denies the settings changes or denies upgrading the firmware. If this setting is disabled, the UR device accepts settings
changes and firmware upgrade.
This role is disabled by default.
FACTORY SERVICE MODE — When Enabled, the device can go into factory service mode. For this setting to become enabled a
Supervisor authentication is necessary. The default value is Disabled.
SUPERVISOR ROLE — When Enabled, the Supervisor role is active. To Disable this setting a Supervisor authentication is
necessary. If disabled, the Supervisor role is not allowed to log in. In this case, the Administrator can change the settings
under the Supervisory menu.
If enabled, Supervisor authentication is required to change the settings in the Supervisory menu. If the Supervisor disables
their role after authentication, the Supervisor session remains valid until they switch to another role using MMI or until they
end the current Supervisor session if using communications.
This role is disabled by default.
SERIAL INACTIVITY TIMEOUT — The role logged via a serial port is auto logged off after the Serial Inactivity timer times out. A
separate timer is maintained for RS232 and RS485 connections. Set this value to a high number, such as eight minutes,
when using the rear RS485 terminals for settings write.
GE recommends setting this value to at least 3 minutes for the following scenario: while connected to a CyberSentry
device, with serial or USB cable connected to the front panel, and performing "Add Device to Offline Window" or an online/
offline comparison. With less than the recommended 3 minutes, the serial activity timeout interrupts the connection and
the security role login window appears. Upon login, the process resumes.
Self-tests
SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY  SELF TESTS
 SELF TESTS  FAILED See below
   AUTHENTICATE

FIRMWARE LOCK: Range: Enabled, Disabled

 Enabled
SETTINGS LOCK: Range: Enabled, Disabled

 Enabled
FAILED AUTHENTICATE — If this setting is Enabled then the number of failed authentications is compared with the Session
Lockout threshold. When the Session Lockout threshold is exceeded, this minor alarm indication comes up.
FIRMWARE LOCK — If this setting is Enabled, then any firmware upgrade operation attempt when the Lock Relay setting is
enabled brings up this self test alarm.
SETTINGS LOCK — If this setting is Enabled then an unauthorized write attempt to a setting for a given role activates this self
test.
SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY  SELF TESTS  FAILED AUTHENTICATE
 FAILED FAILED AUTHENTICATE: Range: Enabled, Disabled
 AUTHENTICATE  Enabled
CyberSentry setup
When first using CyberSentry security, use the following procedure for setup.
1. Log in to the relay as Administrator by using the VALUE keys on the front panel to enter the default password
"ChangeMe1#". Note that the Lock Relay setting needs to be disabled in the Security > Supervisory menu. When this
setting is disabled, configuration and firmware upgrade are possible. By default, this setting is disabled.
2. Enable the Supervisor role if you have a need for it.
3. Make any required changes in configuration, such as setting a valid IP address for communication over Ethernet.
4. Log out of the Administrator account by choosing None. 5
5. Next, Device or Server authentication can be chosen on the login screen, but the choice is available only in EnerVista.
Use Device authentication to log in using the five pre-configured roles (Administrator, Supervisor, Engineer, Operator,
Observer). When using a serial connection, only Device authentication is supported. When Server authentication is
required, characteristics for communication with a RADIUS server must be configured. This is possible only in the
EnerVista software. The RADIUS server itself also must be configured. The appendix called RADIUS Server at the end of
this instruction manual gives an example of how to set up a simple RADIUS server. Once both the RADIUS server and
the parameters for connecting the UR to the server have been configured, you can choose Server authentication on
the login screen of EnerVista.
The use of CyberSentry for devices communicating through an Ethernet-to-RS485 gateway is not
supported. Because these gateways do not support the secure protocols necessary to communicate
with such devices, the connection cannot be established. Use the device as a non-CyberSentry
device.
Users logged in through the front panel are not timed out and cannot be forcefully logged out by a
supervisor. Roles logged in through the front panel that do no allow multiple instances (Administrator,
Supervisor, Engineer, Operator) must switch to None (equivalent to a logout) when they are done in
order to log out.
For all user roles except Observer, only one instance can be logged in at a time, for both login by front
panel and software.
To configure Server authentication:
1. In the EnerVista software, choose Device authentication and log in as Administrator.
2. Configure the following RADIUS server parameters: IP address, authentication port, shared secret, and vendor ID.
3. On the RADIUS server, configure the user accounts. Do not use the five pre-defined roles as user names (Administrator,
Supervisor, Engineer, Operator, Observer) in the RADIUS server. If you do, the UR relay automatically provides the
authentication from the device.
4. In the EnerVista software, choose Server authentication and log in using the user name and password configured on
the RADIUS server for Server authentication login.

5. After making any required changes, log out.
When changing settings offline, ensure that only settings permitted by the role that performs the
settings download are changed because only those changes are applied.
Pushbuttons (both user-control buttons and user-programmable buttons) located on the front panel can be pressed by an
Administrator or Engineer role. This also applies to the RESET button, which resets targets, where targets are errors
displayed on the front panel or the Targets panel of the EnerVista software. The RESET button has special behavior in that it
allows these two roles to press it even when they are logged in through the RS232 port and not through the front panel.
To reset the security event log and self-test operands:
1. Log in as Supervisor (if the role is enabled) or Administrator (if the Supervisor role is disabled) and execute a clear
security command under Commands > Security > Clear Security.
Security events
The security events produced when the CyberSentry option is purchased are sent as sytem log (syslog) messages to a
syslog server, if one is configured. The format is as follows.
Security log Event Number Date & Username IP address Role Activity Value
Timestamp
Event Number — Event identification number (index)

Date & Timestamp — UTC date and time
Username — 255 chars maximum, but in the security log it is truncated to 20 characters
IP address — Device IP address
5 Role — 16 bit unsigned, of type format F617
Enumeration Role
0 None
1 Administrator
2 Supervisor
3 Engineer
4 Operator
5 Factory
Activity Value — 16 bit unsigned
Enumeration Description
1 Authentication Failed
2 User Lockout
3 FW Upgrade
4 FW Lock
5 Settings Lock
6 Settings Change. Because this can fill the entire event log, it is supported by the
already existing Settings_Change.log file. This event is not required.
7 Clear Oscillography command
8 Clear Data Logger command (not applicable to all UR products)
9 Clear Demand Records command (not applicable to all UR products)
10 Clear Energy command (not applicable to all UR products)
11 Clear Unauthorized Access command
12 Clear Teleprotection Counters command (not applicable to all UR products)
13 Clear All Relay Records command
14 Role Log in

Enumeration Description
15 Role Log off
In addition to supporting syslog, a B90 with CyberSentry also saves the security events in two local security files, these
being SECURITY_EVENTS.CSV and SETTING_CHANGES.LOG. Details on these files and how to retrieve them are available in
the EnerVista software under Maintenance > Retrieve File. Depending on the level of criticality/severity, a syslog server or
a reporting tool gathering information from a syslog server can produce reports, charts, and so on. All severity levels are
per RFC 5424.
Table 5-6: CyberSentry system events recorded
Event Severity Description
FAILED_AUTH, ORIGIN, TIMESTAMP Notice (5) A failed authentication with origin information (username and IP:MAC
address), a time stamp in UTC time when it occurred
AUTH_LOCKOUT, ORIGIN, TIMESTAMP Warning (4) An authentication lockout has occurred because of too many failed
authentication attempts
FIRMWARE_UPGD, ORIGIN, Information (6) Indicates that a change of firmware has occurred
TIMESTAMP
FIRMWARE_LOCK, ORIGIN, Warning (4) An attempt was made to change firmware while the firmware lock was
TIMESTAMP enabled
SETTING_CHG, ORIGIN, TIMESTAMP Notice (5) Indicates setting change(s)
SETTING_LOCK, ORIGIN, TIMESTAMP Warning (4) An attempt was made to change settings while the settings lock was enabled
LOGIN, ORIGIN, TIMESTAMP Information (6) Indicates when a certain role logged in
LOGOUT, ORIGIN, TIMESTAMP Information (6) Indicates when a certain role logged out or timed out
CLEAR_OSCILLOGRAPHY Notice (5) Clear oscillography command was issued
CLEAR_DATA_LOGGER
CLEAR_DEMAND_RECS
Notice (5)
Notice (5)
Clear data logger command was issued
Clear demand records command was issued
5
CLEAR_ENERGY Notice (5) Clear energy command was issued
RESET_UNAUTH_ACCESS Notice (5) Reset Unauthorized access command was issued
CLEAR_TELEPROTECTION_CNT Notice (5) Clear teleprotection counters command was issued
CLEAR_ALL_RECS Notice (5) Clear all records command was issued
WRITE_SETTING_FILE Notice (5) Write settings file to the relay
5.3.3 Display properties

SETTINGS  PRODUCT SETUP  DISPLAY PROPERTIES
 DISPLAY LANGUAGE: Range: English; English, French; English, Russian; English,
 PROPERTIES  English Chinese; English, German (examples; depends on order code)
Visible when language other than English purchased
FLASH MESSAGE Range: 0.5 to 10.0 s in steps of 0.1

 TIME: 1.0 s
DEFAULT MESSAGE Range: 10 to 900 s in steps of 1

 TIMEOUT: 300 s
DEFAULT MESSAGE Range: 25%, 50%, 75%, 100%

 INTENSITY: 25 % Visible when a VFD is installed
SCREEN SAVER Range: Disabled, Enabled

 FEATURE: Disabled Visible when an LCD is installed
SCREEN SAVER WAIT Range: 1 to 65535 min. in steps of 1

 TIME: 30 min Visible when an LCD is installed
CURRENT CUT-OFF Range: 0.002 to 0.020 pu in steps of 0.001

 LEVEL: 0.020 pu
VOLTAGE CUT-OFF Range: 0.1 to 1.0 V secondary in steps of 0.1

 LEVEL: 1.0 V

Some relay messaging characteristics can be modified to suit different situations using the display properties settings.
LANGUAGE — This setting selects the language used to display settings, actual values, and targets. This setting displays
when a language other than English was purchased, and the range depends on the order code of the relay.
For Japanese, the settings display in Japanese on the graphical front panel, while the keys printed on the panel are in
English.
For Japanese and Chinese, up to 10 characters can be input in a field on the graphical front panel, not 20.
With the graphical front panel, the language can be changed regardless of the language purchased. That is, all languages
can be used. If you select a language with which you are unfamiliar and want to switch back to English for example, the
menu order remains the same. That is, Settings is always second, Product Setup is always first, Display Properties is always
second, and Language is always first.
If the language is changed after entering user-configured names, such as relay names, the strings are not translated. For
example, a relay name is entered in English, the language is changed to Japanese, and the relay name remains in English.
Set the language before changing settings.
The language can be selected also for the front panel in EnerVista under Maintenance > Change Front Panel.
The language of the EnerVista software can be changed under View > Language. Languages supported by the operating
system display; that is for Polish or Japanese to display, the software needs to be installed on a Polish or Japanese
operating system.
FLASH MESSAGE TIME — Flash messages are status, warning, error, and information messages displayed in response to
certain key presses during settings programming. These messages override any normal messages. Use this setting to
change the duration of flash messages on the display.
DEFAULT MESSAGE TIMEOUT — If the keypad is inactive for a period of time, the relay automatically reverts to a default
message. The inactivity time is modified using this setting to ensure that messages remain on the screen long enough
5 during programming or reading of actual values. This setting is not supported on the graphical front panel.
DEFAULT MESSAGE INTENSITY — To extend phosphor life in the vacuum fluorescent display, the brightness can be
attenuated during default message display. During keypad interrogation, the display always operates at full brightness.
This setting is not supported on the graphical front panel.
SCREEN SAVER FEATURE and SCREEN SAVER WAIT TIME — These settings are only visible if the B90 has a liquid crystal display
(LCD) and control its backlighting. When the SCREEN SAVER FEATURE is “Enabled,” the LCD backlighting turns off after the
DEFAULT MESSAGE TIMEOUT followed by the SCREEN SAVER WAIT TIME, provided that no keys have been pressed and no
target messages are active. When a keypress occurs or a target becomes active, the LCD backlighting turns on. These
settings are not supported on the graphical front panel.
CURRENT CUT-OFF LEVEL — This setting modifies the current cut-off threshold. Very low currents (1 to 2% of the rated value)
are very susceptible to noise. Some customers prefer very low currents to display as zero, while others prefer the current to
display even when the value reflects noise rather than the actual signal. The B90 applies a cut-off value to the magnitudes
and angles of the measured currents. If the magnitude is below the cut-off level, it is substituted with zero. This applies to
phase and ground current phasors as well as true RMS values and symmetrical components. The cut-off operation applies
to quantities used for metering, protection, and control, as well as those used by communications protocols. Note that the
cut-off level for the sensitive ground input is 10 times lower that the CURRENT CUT-OFF LEVEL setting value. Raw current
samples available via oscillography are not subject to cut-off.
VOLTAGE CUT-OFF LEVEL — This setting modifies the voltage cut-off threshold. Very low secondary voltage measurements
(at the fractional volt level) can be affected by noise. Some customers prefer these low voltages to be displayed as zero,
while others prefer the voltage to be displayed even when the value reflects noise rather than the actual signal. The B90
applies a cut-off value to the magnitudes and angles of the measured voltages. If the magnitude is below the cut-off level,
it is substituted with zero. This operation applies to phase and auxiliary voltages, and symmetrical components. The cut-off
operation applies to quantities used for metering, protection, and control, as well as those used by communications
protocols. Raw samples of the voltages available via oscillography are not subject to cut-off.
Lower the VOLTAGE CUT-OFF LEVEL and CURRENT CUT-OFF LEVEL with care as the relay accepts lower signals as valid
measurements. Unless dictated otherwise by a specific application, the default settings of “0.02 pu” for CURRENT
CUT-OFF LEVEL and “1.0 V” for VOLTAGE CUT-OFF LEVEL are recommended.

The graphical front panel is a hardware option. See the Order Codes section in chapter 2 for details.
Use the EnerVista software to configure the graphical front panel. The settings are not accessible from the graphical front
panel.
The following screens are available:
• Home page
• Rolling mode
• Metering editor
• Single-line diagram editor
• Annunciator editor
• Configurable navigation
The settings menu itself and the event record pages are not configurable.
Multiple screens can be opened in the EnerVista software, but the first remains active and the others can be read-only. For
example, the Annunciator Editor and Single Line Diagram Editor can be open and active, then subsequently opened Rolling
Mode and Home Page screens are read-only. Close the windows, then re-open the one required.
5.3.4.1 Home page

This window sets the home page displayed on the graphical front panel and the date and time formats for all pages. Home
page options include display of product information, alarms, actual values, and event records. 5
The path is Settings > Product Setup > Graphical Panel > Home Page. The menu does not display when there is no
graphical front panel.
Figure 5-4: Home page with product information
Setting Group
Alarm Target Relay Date and Time
859850A1.cdr

Figure 5-5: Home page settings
Home Page Content

Range: Product Information, SLD 1…5, Annunciator, Annunciator 1…8, Phasors 1…6, Tabular 1…5, Event Records, Targets
Default: Product Information
This setting specifies the page to display between the home page header and footer. Pressing the Home button returns
the display to this page. The home page displays for the rolling mode delay specified, then changes to the rolling mode
pages.
The "Annunciator" option without a page number specifies the first annunciator page in the following sequence:
– The first annunciator page that contains an annunciator window that is in alarm (fast flash)
– The first annunciator page that contains an annunciator window that is in ringback. Ringback is a "return alert."
Visual and audible signals are given when conditions return to normal, then the sequence returns to normal by
pushing the RESET button.
– The first annunciator page that contains an annunciator window that is in abnormal state
– Annunciator page 1
5 Whenever an annunciator window changes state this list is re-evaluated, which can result in the home page displaying
a different annunciator page.
The Tabular option displays a configured actual values/metering page.
The Targets option displays error messages, such as wrong transceiver, similar to event record entries.
Date Format
Range: yyyy-mm-dd, dd-mmm-yy, yyyy/mm/dd, m/d/yyyy, m/d/yy, mm/dd/yy, mm/dd/yyyy, yy/mm/dd
Default: yyyy-mm-dd
This setting specifies the format for dates on the graphical front panel. It applies to the page header, the events records,
the annunciator, and everywhere else a date displays on the panel. If the relay is synchronized to an external time
source via PTP, IRIG-B, SNTP, and so on, the date/time is shown in white, and otherwise in yellow.
yyyy — four-digit year, for example 2017
yy — two-digit year, for example 17 for 2017
mmm — abbreviation of month name, for example Jan for January
mm — two-digit month, for example 01 for January
m — one or two-digit month, for example 1 for January and 10 for October
dd — two-digit day, for example 08
d — one or two-digit day, for example 8 and 28
To set the date and time, access Synchronize Devices in the software, synchronize to a time source using Settings >
Product Setup > Real Time Clock, or synchronize to the computer using Commands > Set Date and Time.

Time Format
Range: hh:mm:ss, h:mm:ss tt
Default: hh:mm:ss
This setting specifies the format for time on the graphical front panel. It applies to the page header and everywhere else
a time displays on the panel. When the Date Format and the Time Format use the defaults, the date and time are
separated by the character "T" per the ISO convention, such as "2017-09-24T10:58:31". Otherwise the date and time are
separated by a space. If the relay is synchronized to an external time source via PTP, IRIG-B, SNTP, and so on, the date/
time is shown in white, and otherwise in yellow.
hh — two-digit hour, for example 02 for two o’clock
h — one or two-digit hour, for example 2 for two o’clock
mm — two-digit minute, for example 51 minutes
ss — two-digit second (can have a decimal and further digits appended), for example 16 seconds
tt — AM or PM based on 12 hour clock
If microseconds have to be displayed, for example, in the event records, the 24-hour clock is adopted. The representation
of an accumulated period (for example hh:mm) is not affected by the selected time format.
To set the date and time, access Synchronize Devices in the software or synchronize to a time source using Settings >
Product Setup > Real Time Clock.
5.3.4.2 Rolling mode

After a user-defined period of inactivity, the graphical front panel changes, or rolls, to user-selected pages. Up to 10 pages
can be specified. Similarly, the display backlight intensity is lowered to a specified level; lower intensity extends the life of
the display.
Each rolling page displays for a few seconds; duration cannot be set.
5
The path is Settings > Product Setup > Graphical Panel > Rolling Mode.
Figure 5-6: Rolling mode settings
Rolling Mode Delay

Range: 0 to 900 s in steps of 1
Default: 300 s
Set this delay to 0 to disable the rolling mode feature.
Otherwise, after no pushbutton has been pressed for the amount of time specified by this setting, the display
automatically enters rolling mode. While in the rolling mode, the Rolling Mode Pages display. Rolling mode can be
interrupted when a setting changes, such as changing the home page, then resumes rolling.

Automatic Annunciator Recall

Range: Enabled, Disabled
Default: Enabled
When Enabled, an annunciator window changes state, and the display is in rolling mode, this setting terminates rolling
mode and displays the annunciator page containing the changed state.
The Configurable Navigation feature takes precedence over this setting when the Automatic Annunciator Recall and
Configurable Navigation are activated by the same input.
Screen Saver Delay
Range: 0 to 900 s in steps of 1
Default: 300 s
The screen saver mode extends the life of the display. After the amount of time set here, the screen saver activates and
the display intensity is reduced to the level set by the Screen Saver Intensity setting. When in rolling mode, rolling
continues while the screen saver is active. The screen saver terminates when rolling mode terminates. To disable the
screen saver, set the delay to 0.
Screen Saver Intensity
Range: 0, 10, 20, or 30 %
Default: 30 %
This setting sets the brightness of the display while the screen saver is active. For example, 0% means that the screen is
dark and nothing displays. Pressing a pushbutton or changing a setting in the software, for example, re-activates the
display.
Number of Rolling Mode Pages
Range: 1 to 10 in steps of 1
5 Default: 1
This setting specifies the number of rolling pages. During rolling mode, the graphical front panel displays pages from 1
to the selected number.
Rolling Mode Page 1 to 10
Range: Product Information, SLD 1…5, Annunciator, Annunciator 1…8, Phasors 1…6, Tabular 1…5, Event Records, Targets
These settings specify the pages to display on the graphical front panel while in rolling mode.
The "Annunciator" selection without a page number specifies the first annunciator page in the following sequence:
Whenever an annunciator window changes state the list is re-evaluated, which can result in the display of a different
annunciator page in the rolling sequence.
5.3.4.3 Metering editor

This feature creates tables of actual/metered values for the graphical front panel. It configures the content that displays in
the Metering Tab pushbutton. An actual value, status, or text can be displayed. Five tabular metering pages can be
configured. There also can be a phasor page for each configured AC source, and these pages are not configurable.
The path is Settings > Product Setup > Graphical Panel > Metering Editor.
Set the Current Page, Page Name, Layout, configure the top inputs, then the cells. The 16 inputs at the top of the page are
used as inputs for the Status Index fields. Click the Preview button to view the page.

For a phasor diagram, configure the source under Settings > System Setup > Signal Sources. The diagram is then
viewable by pushing the Metering Tab pushbutton on the graphical front panel. The Metering Editor is not used for these
phasor diagrams.
The figures show setup and table preview.
The Cells configured are not retained when using the Convert Device Settings function, for example when converting a
file in the Offline Window from version 7.6 to 7.7.
Figure 5-7: Metering Editor window
Figure 5-8: Preview for graphical front panel

STATUS INPUTS 1 to 16
Range: OFF, ON, any FlexLogic operand
Default: OFF
This setting identifies the potential inputs for use in the STATUS INDEX fields, for display of the status of FlexLogic
operands.
A maximum of eight Status Inputs can be used per metering page, and 16 in all metering pages.
Select the metering input from the drop-down list. The options reflect the FlexLogic operands applicable to the B90. They
are inputs for all five metering pages, not just the current page.
CURRENT PAGE
Range: Page 1...Page 5
Default: Page 1
Select the metering page to configure from the drop-down list. There are five pages possible, viewable with the Tab
pushbuttons on the graphical front panel.
PAGE NAME
Range: Page 1...Page 5
Default: Page 1
Up to 20 characters can be input here as the name of each metering page. The name displays for the Tab pushbutton on
the graphical front panel.
LAYOUT
Range: 3x4, 4x6, 6x8, 6x4, 8x6, 12x8, 12x4, 16x6, 18x8
Default: 6x4
This setting determines how many rows and columns display on the graphical front panel with the metering information.
5 The configurable rows in the settings window change dynamically based on this setting.
CONTENT
Range: Actual, Status, Text
Default: Text
Select the type of content to display.
– Actual — an actual value/data. The Configure button becomes active for the actual value to be selected.
– Status — one of the operands selected from the STATUS INPUTS fields. Select it in the STATUS INDEX field.
– Text — indicates that text is to display instead of a metered value
STATUS INDEX
Range: 1...16
Default:
This field becomes active when the CONTENT field is set to Status. It selects the input from the STATUS INPUTS to display
the on/off status of the selected operand.
A maximum of eight Status Inputs can be used per metering page, and 16 in all metering pages.
TEXT
Range: up to 20 alphanumeric characters
Default:
Enter the text to display on the graphical front panel. This field is active when the CONTENT field is set to Text or Status.
When Status is selected, the text displays when the status input is in the "on" state.
OFF TEXT
Default:
Enter the text to display on the graphical front panel when the element being monitored is in an off/closed state. This
field is active when the CONTENT field is set to Status. The text displays when the status input is in the "off" state.

FONT
Range: 16, 18, 20
Default: 16
Set the font size to display on the graphical front panel.
TEXT COLOR
Range: 24-bit color selector
Default: Black
Set the text color to display in the specified cell.
BACK COLOR
Default: Grey
Set the background color to display in the specified cell.
ACTUAL (Configure)
Range: Configure
Default: Configure
The Configure button becomes active when the CONTENT field is set to "Actual." The window specifies the metering
data to display.
Figure 5-9: Metering value properties window
Parameter
Range: any FlexAnalog parameter
Default:
This setting selects a FlexAnalog parameter that specifies the metered value to display in the metering window. A
FlexAnalog is an analog parameter.
Units
Range: up to eight alphanumeric characters
Default:
This setting specifies the units of measurement for the metered value and is populated based on the Parameter
selected. The field can be left blank when units of measure do not apply.
Scale Factor
Range: G Giga, M Mega, k Kilo, None
Default: None
This setting allows the user to specify the scaling factor for the metering units value. Options depend on the Parameter.

Multiplier
Range: -1000000 to 1000000
Default: 1.0
This setting allows the user to specify a multiplier for the metering parameter value. The multiplier must be in
compliance with the 32-bit floating-point format per IEEE 754, otherwise, the input value is represented as per the IEEE
standard. For example, 1234.56789 is represented as 1234.567871094, and 9876.54321 as 9876.54296875.
Number of Integers
Default: 1
This setting specifies the number of integers in the displayed metered value. It can be used to provide for leading
character spacing of the display value.
For example, setting the number to 2 displays 00.000[V] and setting it to 3 displays 000.000[V].
Number of Decimals
Default: 3
This setting specifies the number of decimal places in the displayed metered value. For example, setting the number to 1
displays 0.0 and setting it to 2 displays 0.00.
5.3.4.4 Single-line diagram editor

The path is Settings > Product Setup > Graphical Panel > Single Line Diagram Editor. Use is explained in the Interfaces
chapter.
5 5.3.4.5 Annunciator editor

The annunciator editor is used to create annunciator content for the graphical front panel, including alarms and actual
values. Use is explained in the Interfaces chapter.
The path is Settings > Product Setup > Graphical Panel > Annunciator Editor.
To add an alarm, access the Annunciator Editor, configure the Layout and Page Name, configure the alarm or actual value,
set the text and color, then save. On the graphical front panel, view the content by pressing the Annunciator Tab
pushbutton at the bottom of the Home page. (Alarms do not display automatically.) Acknowledge the alarm by navigating
to it with the arrow pushbuttons, then pressing the ENTER or RESET pushbutton.
The figure shows alarms for basic functions. The last annunciator page is named Device Alarms. Alarms are set for the
device being offline, Ethernet cable issues, unauthorized access, battery failure, and high ambient temperature. They can
reset themselves when conditions return to normal, except for unauthorized access and temperature monitoring, which
require the alarms to be acknowledged. The self-test error functions, here for Ethernet and battery failures, also have been
enabled under Settings > Product Setup > User-Programmable Self Tests (not shown). When the alarms are triggered,
they display with a red background. An alarm is acknowledged by using the arrow keys on the graphical front panel then
pressing the ENTER button.

Figure 5-10: Annunciator editor with preview shown
Reset
Range: ON, OFF, any FlexLogic operand
Default: OFF
This setting selects a FlexLogic operand that when activated acknowledges/resets all annunciator windows in the
graphical front panel. For example, to have the first user pushbutton resets all alarms, set this to PUSHBUTTON 1 ON and
turn on the pushbutton under Settings > Product Setup > User-Programmable Pushbuttons. This setting is the same
as the one defined in Settings > Inputs/Outputs > Resetting > Reset Annunciator. See the Resetting section later in this
chapter.
LAYOUT
Range: 3x4, 4x6, 6x8
Default: 3x4
Selects the number of rows and columns to display on the annunciator pages. For example, 3x4 means 12 windows
display per page over eight pages. Up to 96 entries are possible.
To view the layout, click the Preview button.
PAGE NAMES
Default: Page 1...Page 8
Up to 20 characters can be input as the name of each annunciator page. The number of pages depends on the Layout.
The name displays for the Tab pushbutton on the graphical front panel.

PARAMETER
Range: Indicator 1...Indicator 96
Default: Indicator 1...Indicator 96
Read-only field. Up to 96 windows are possible.
CONTENT
Range: Actual, Alarm, Mixed
Default: Alarm
Select if the cell is to be an alarm, an actual value, or a combination thereof, for example consists of a single metered
value (set to “Actual”), contains a single alarm indication (set to “Alarm”), or contains both a metered value and an alarm
indication (set to “Mixed”).
ALARM INPUT
Range: OFF, ON, any FlexLogic operand
Default: OFF
Select a trigger for the alarm, or the input signal connected to the alarm. For example, when set to "FIRST ETHERNET
FAIL" and the Ethernet cable connected to port 1 is removed, the alarm is triggered. (Note that when the Ethernet cable
is inserted into an SFP connector and the SFP connector is removed, the alarm is not triggered.) The field is read-only for
an actual value.
The selectable options are the FlexLogic operands specific to the product.
ALARM TYPE
Range: Acknowledgeable, Self Reset, Latched
Default: Acknowledgeable
Set the alarm type. The field is read-only for an actual value.
5 Acknowledgeable — Follow the state transitions, as outlined in the Annunciator section of the Interfaces chapter. The
alarm blinks until acknowledged, then remains on until the condition clears.
Self Reset — Track the state of the input operand. The alarm turns on when the trigger activates and off when the trigger
clears.
Latched — Alarm is on until acknowledged/reset individually or until the RESET button is pressed.
To acknowledge/reset/unlatch an alarm, use the arrow buttons on the graphical front panel and press the ENTER
button.
TEXT (LINE 1 to 3)
Default:
The text that displays in the annunciator cell. Three lines can be displayed. Note that a specified metering value replaces
the text for the selected line. This means that a line can display text or be set to show an actual metered value. If the text
does not display it is because an actual metered value is over-riding it; change the line for the text or for the actual value.
TEXT COLOR
Default: White
The color to display for the three text or actual value lines specified.
BACK COLOR
Default: Red
The background color to display for any triggered cell, for example when an alarm is triggered.
ACTUAL (Configure)
Range: Configure
Default: Configure
The Configure button becomes active when the CONTENT field is set to "Actual" or "Mixed." The window specifies the
metering data to display.

Parameter
Range: any FlexAnalog parameter
Default:
This setting selects a FlexAnalog parameter that specifies the metered value to display in the annunciator alarm.
Units
Range: up to eight alphanumeric characters
Default:
This setting specifies the units of measurement for the metered value and is populated based on the Parameter
selected. The field can be left blank when units of measure do not apply.
Scale Factor
Range: G Giga, M Mega, k Kilo, None
Default: None
This setting allows the user to specify the scaling factor for the metering units value. Options depend on the Parameter.
Multiplier
Range: -1000000 to 1000000
Default: 1.0
This setting allows the user to specify a multiplier for the metering parameter value. The multiplier must be in
compliance with the 32-bit floating-point format per IEEE 754, otherwise, the input value is represented as per the IEEE
standard. For example, 1234.56789 is represented as 1234.567871094, and 9876.54321 as 9876.54296875.
Number of Integers
Default: 1
This setting specifies the number of integers in the displayed analog value. It can be used to provide for leading 5
character spacing of the display value.
For example, setting the number to 2 displays 00.000[V] and setting it to 3 displays 000.000[V].
Number of Decimals
Default: 3
This setting specifies the number of decimal places in the displayed analog value. For example, setting the number to 1
displays 0.0 and setting it to 2 displays 0.00.
Display in Line
Range: 1, 2, 3
Default: 1
This setting specifies the line in the annunciator alarm window to display the metered value. The actual value replaces
the text for the selected line. For example, 2 means the value displays in line 2 of the text; any text configured to display
in that line does not display.
5.3.4.6 Configurable navigation

The path is Settings > Product Setup > Graphical Panel > Configurable Navigation.
This feature allows FlexLogic operands to trigger page display on the graphical front panel. It consists of 64 setting pairs,
each with a condition and an activation page. The condition selects any FlexLogic operand. The activation page selects
any page available for the graphical front panel. The page opens whenever the selected operand transitions from Off to
On. The page remains open until rolling mode initiates, another trigger initiates from Configurable Navigation, or the Home
button is pressed.
Avoid selecting condition operands that are likely to operate simultaneously but activate different pages, as only one page
can be opened at a time. For example, do not select a single-line diagram page for breaker status open and select an
annunciator page for a trip alarm.

In the example shown, failure of any of the three Ethernet ports triggers the Product Information page to display. With
unauthorized access (such as wrong password), IRIG-B clock failure, or breaker trouble, the Event Records display. When a
breaker opens, a single-line diagram displays. For the Ethernet and IRIG-B failure operation to work, these functions also
have been enabled under Settings > Product Setup > User-Programmable Self Tests.
Figure 5-11: Configurable navigation editor
To use the feature, select a CONDITION, select an ACTIVATE PAGE, then save.
CONDITION
5 Range: OFF, ON, any FlexLogic operand

Default: OFF
Select the FlexLogic operand for the trigger. When it transitions from Off to On, it opens the page specified by the
ACTIVATE PAGE setting. The FlexLogic operands selectable depend on product. Select it from the drop-down list. Or click
or select the field and start typing to auto-fill. For example, typing F displays FIRST ETHERNET FAIL, while typing BR
displays the first breaker option.
ACTIVATE PAGE
Range: Product Information, SLD 1…5, Annunciator, Annunciator 1…8, Actual Values Phasors 1…6, Tabular 1…5, Event
Records, Targets
This setting specifies the page to display on the graphical front panel when the FlexLogic operand selected by its
CONDITON setting transitions from Off to On.
The "Annunciator" option without a page number specifies the first annunciator page in the following sequence:
5.3.5 Clear relay records

SETTINGS  PRODUCT SETUP  CLEAR RELAY RECORDS
 CLEAR RELAY CLEAR USER REPORTS: Range: FlexLogic operand
 RECORDS  Off

CLEAR EVENT RECORDS: Range: FlexLogic operand

 Off
CLEAR OSCILLOGRAPHY: Range: FlexLogic operand

 Off
RESET UNAUTH ACCESS: Range: FlexLogic operand

 Off
CLEAR DIR I/O STATS: Range: FlexLogic operand

 Off Visible only for units with Direct I/O module
RESET UNAUTH ACCESS — Resets the access restriction counter.

Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user-
programmable pushbuttons to clear specific records is a typical application for these commands. Since the B90 responds
to rising edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Clearing records with user-programmable operands is not protected by the command password. However, user-
programmable pushbuttons are protected by the command password. Thus, if they are used to clear records, the user-
programmable pushbuttons can provide extra security if required.
For example, to assign user-programmable pushbutton 1 to clear demand records, apply the following settings.
1. Assign the clear demand function to pushbutton 1 by making the following change in the SETTINGS  PRODUCT SETUP
 CLEAR RELAY RECORDS menu:
CLEAR DEMAND: “PUSHBUTTON 1 ON”
2. Set the properties for user-programmable pushbutton 1 by making the following changes in the SETTINGS  PRODUCT
SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 menu:
PUSHBUTTON 1 FUNCTION: “Self-reset”
PUSHBTN 1 DROP-OUT TIME: “0.20 s” 5
5.3.6 Communications
5.3.6.1 Menu
SETTINGS  PRODUCT SETUP  COMMUNICATIONS
 COMMUNICATIONS  SERIAL PORTS See page 5-38
  
 NETWORK See page 5-41

 
 IPv4 ROUTE TABLE See page 5-44

 
 MODBUS PROTOCOL See page 5-47

 
 PROTOCOL See page 5-47

 
 DNP PROTOCOL See page 5-48

 
 DNP / IEC104 See page 5-52

  POINT LISTS
 IEC 61850 PROTOCOL Access in EnerVista

  See page 5-52
 WEB SERVER See page 5-92

  HTTP PROTOCOL

 TFTP PROTOCOL See page 5-93

 
 IEC 60870-5-104 See page 5-93

  PROTOCOL
 IEC103 See page 5-95

  PROTOCOL
 USB 2.0 PORT See page 5-100

 
5.3.6.2 Serial ports

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  SERIAL PORTS
 SERIAL PORTS RS232 BAUD Range: 19200, 115200
  RATE: 115200
RS485 COM2 BAUD Range: 300, 1200, 2400, 4800, 9600, 14400, 19200,
 RATE: 19200 28800, 33600, 38400, 57600, 115200 bit/s
RS485 COM2 PARITY: Range: None, Odd, Even

 Even
RS485 COM2 RESPONSE Range: 0 to 1000 ms in steps of 10

 MIN TIME: 0 ms
The front RS232 port applies to enhanced and basic front panels.
RS232 BAUD RATE, RS485 COM2 BAUD RATE, and PARITY — The B90 is equipped with two independent serial communication
5 ports. The front panel RS232 port (USB port with graphical front panel) is intended for local use. The rear COM2 port is
RS485 and has settings for baud rate and parity. It is important that these parameters agree with the settings used on the
computer or other equipment that is connected to these ports. Any of these ports can be connected to a computer
running the EnerVista software, for example to download and upload setting files, view measured parameters, and
upgrade the relay firmware. A maximum of 32 relays can be daisy-chained and connected to a DCS, PLC, or computer
using the RS485 ports. If IEC 60870-103 is chosen as the protocol, valid baud rates are 9600 and 19200 bit/s, and valid
parity is Even.
RS485 COM2 RESPONSE MIN TIME — This setting specifies the minimum time before the rear RS485 port transmits after
receiving data from a host. This feature allows operation with hosts that hold the RS485 transmitter active for some time
after each transmission.
5.3.6.3 Ethernet network topology

The B90 has three Ethernet ports. Each Ethernet port must belong to a different network or subnetwork. Configure the IP
address and subnet to ensure that each port meets this requirement. Two subnets are different when the bitwise AND
operation performed between their respective IP address and mask produces a different result. Communication becomes
unpredictable when more than one port is configured to the same subnet.
Example 1
IP1/Mask1: 10.1.1.2/255.255.255.0 (where LAN 1 is 10.1.1.x/255.255.255.0)
IP2/Mask2: 10.2.1.2/255.255.255.0 (where LAN2 is 10.2.1.x/255.255.255.0)
IP3/Mask3: 10.3.1.2/255.255.255.0 (where LAN3 is 10.3.1.x/255.255.255.0)
Example 2
IP1/Mask1: 10.1.1.2/255.0.0.0 (where LAN1 is 10.x.x.x/255.0.0.0)

Example 3 — Incorrect
IP1/Mask1: 10.1.1.2/255.0.0.0
IP2/Mask2: 10.2.1.2/255.0.0.0
IP3/Mask3: 10.3.1.2/255.0.0.0
This example is incorrect because the mask of 255.0.0.0 used for the three IP addresses makes them belong to the same
network of 10.x.x.x.
Single LAN, no redundancy

The topology shown in the following figure allows communications to SCADA, local configuration/monitoring through
EnerVista, and access to the public network shared on the same LAN. No redundancy is provided.
Figure 5-12: Network configuration for single LAN
Public Network
SCADA
EnerVista Software
LAN1 5
ML3000
P1
IP1/ P2 P3
MAC1
UR
859708A2.vsd
Multiple LANS, with redundancy

The following topology provides local configuration/monitoring through EnerVista software and access to the public
network shared on LAN1, to which port 1 (P1) is connected. There is no redundancy provided on LAN1. Communications to
SCADA is provided through LAN2. P2 and P3 are connected to LAN2, where P2 is the primary channel and P3 is the
redundant channel. In this configuration, P3 uses the IP and MAC addresses of P2.

Figure 5-13: Multiple LANs, with redundancy
Public Network
SCADA
EnerVista Software
LAN1 LAN2
LAN2
ML3000
ML3000 ML3000
P1 P2 P3
IP1/ IP2/ IP2/
MAC1 MAC2 MAC2
Redundancy mode
UR
859709A4.vsd
5 Multiple LANS, no redundancy

The following topology provides local configuration/monitoring through EnerVista software on LAN1, to which port 1 (P1) is
connected, access to the public network on LAN2, to which port 2 (P2) is connected, and communications with SCADA on
LAN3, to which port 3 (P3) is connected. There is no redundancy.
Figure 5-14: Multiple LANS, no redundancy
Public Network
SCADA
EnerVista Software
LAN1 LAN2
LAN3
ML3000
ML3000 ML3000
P1 P2 P3
IP1/ IP2/ IP3/
MAC1 MAC2 MAC3
UR
859710A2.vsd

5.3.6.4 Network
As outlined in the previous section, when using more than one Ethernet port, configure each to belong to a different
network or subnet using the IP addresses and mask. Configure the network IP and subnet settings before configuring the
routing settings.
Follow the IP and subnet mask rules outlined in the Set IP Address in UR section of the Installation chapter.
To obtain a list of all port numbers used, for example for audit purposes, contact GE technical support with substantiating
information, such as the serial number and order code of your device.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK 1(3)
 NETWORK PORT 1 PRT1 IP ADDRESS: Range: standard IPV4 address format
  127.0.0.1
PRT1 SUBNET IP MASK: Range: standard IPV4 address format

 255.0.0.0
PRT1 FUNCTION: Range: Enabled, Disabled

 Enabled

  127.0.0.1

 255.0.0.0
PRT2 REDUNDANCY: Range: None, Failover, PRP

 None Range if no PRP license: None, Failover
 PRP MCST ADDR: Range: 01-15-4E-00-01-00 to 01-15-4E-00-01-FF 5

01154E000100

 Enabled

  127.0.0.1

 255.0.0.0

 Enabled
The IP addresses are used with the DNP, Modbus/TCP, IEC 61580, IEC 60870-5-104, TFTP, HTTP, and PRP protocols. PRP is
explained in its own section later.
Use the front panel to change these settings. When online, the EnerVista software can be used to enable/disable each port
only. In the Offline Window area, all settings can be changed except port 2 redundancy (depending on firmware version).
When using GOOSE, in failover or PRP mode, port 3 configuration in the CID file is ignored. The Port 3 ConnectedAP
elements has no meaning, as ports 2 and 3 use the port 2 MAC address, IP address, and mask.
PRT1 (2 or 3) IP ADDRESS — This setting sets the port’s IPv4 address in standard IPV4 format. This setting is valid on port 3 if
port 2 REDUNDANCY is set to None.
PRT1 (2 or 3) SUBNET MASK — This setting sets the port’s IPv4 subnet mask in standard IPV4 format. This setting is valid on
port 3 if port 2 REDUNDANCY is set to None.
PRT1 (2 or 3) FUNCTION — This setting enable/disables network communication on the respective port. When the port
function is Disabled, the network traffic on this port is disabled. The PRT2 redundancy setting has no effect on this
functionality. The change takes effect upon relay restart.

If you disable a port here that is used to communicate between the relay and the software, this can take down all
communication between the two. For example, an Ethernet connection set to the IP address of the relay can be disabled
and cannot be reached, even when pinging. The port needs to be re-enabled, IP and any gateway addresses need to be
checked, and the relay needs to be set to Programmed.
PRT2 REDUNDANCY — Determines if ports 2 and 3 operate in redundant or independent mode. If a license for PRP was
purchased, the options are None, Failover, and PRP. If a license for PRP was not purchased, the options are None and
Failover. In non-redundant mode (REDUNDANCY set to None), ports 2 and 3 operate independently with their own MAC, IP,
and mask addresses. If REDUNDANCY is set to Failover, the operation of ports 2 and 3 is as follows:
• Ports 2 and 3 use the port 2 MAC address, IP address, and mask
• The configuration fields for IP address and mask on port 3 are hidden
• Port 3 is in standby mode and does not actively communicate on the Ethernet network but monitors its link to the
Multilink switch. If port 2 detects a problem with the link, communications is switched to Port 3. Port 3 is, in effect,
acting as a redundant or backup link to the network for port 2. Once port 2 detects that the link between itself and the
switch is good and that communication is healthy for five minutes, then switching back to port 2 is performed. The
delay in switching back ensures that rebooted switching devices connected to the B90, which signal their ports as
active prior to being completely functional, have time to completely initialize themselves and become active. Once
port 2 is active again, port 3 returns to standby mode.
If REDUNDANCY is set to PRP, the operation of ports 2 and 3 is as follows:
• Ports 2 and 3 use the port 2 MAC address, IP address, and mask
• The configuration fields for IP address and mask on port 3 are overwritten with those from port 2. This is visible on the
front panel but not displayed in the EnerVista software.
• Port 2 MCST ADDRESS field is visible
• The port 2 PTP function still uses only port 2 and the port 3 PTP function still uses only port 3. The relay still
5 synchronizes to whichever port has the best master. When ports 2 and 3 see the same master, as is typically the case
for PRP networks, the port with the better connectivity is used.
Behavior for GOOSE messages is as follows:
• If REDUNDANCY is set to Failover or PRP, In order to transmit a GOOSE message on port 2, the CID file must be
configured to have the corresponding GSE element in both ConnectedAPs S2 and S3. In the EnerVista software, the
TxGOOSE PORT ASSIGNMENT needs to be "Ports-1,2,3" to transmit GOOSE on both ports 1 and 2, or "Ports-2,3" to have
GOOSE only on port 2, with failover/ PRP.
• If REDUNDANCY is set to PRP, the port 2 configured GOOSE message is simultaneously transmitted on ports 2 and 3
• If REDUNDANCY is set to failover and the port 2 link fails, then only the port 2 configured GOOSE message is transmitted
on port 3
The two ports must be connected to completely independent LANs with no single point of failure, such as common
power supplies that feed switches on both LANs.
For any changes to this setting to take effect, restart the unit.
PRT2 PRP MCST ADDR — This setting allows the user to change the multicast address used by the PRP supervision frames.
This setting is available if REDUNDANCY is set to PRP. All devices in the same PRP network need to have the same multicast
address. Choose an address that does not conflict with another multicast protocol.
5.3.6.5 Far-End Fault Indication (FEFI)

Since 100BASE-FX does not support Auto-Negotiation, a Far-End Fault Indication (FEFI) feature is included since UR 7 that
allows for detection of link failures.
The purpose of the Far-End Fault feature is to allow the stations on both ends of a pair of fibers to be informed when there
is a problem with one of the fibers. Without the Far-End Fault feature, it is impossible for a fiber interface to detect a
problem that affects only its transmit fiber.
When the Far-End Fault feature is supported, a loss of receive signal (link) causes the transmitter to generate a Far-End
Fault pattern in order to inform the device at the far end of the fiber pair that a fault has occurred.

When the local receiver again detects a signal, the local transmitter automatically returns to normal operation.
If a Far-End Fault pattern is received by a fiber interface that supports the Far-End Fault feature and it is enabled, it reacts
by dropping the link as if there were no signal at all.
If the receiving interface does not support the Far-End Fault feature or has it disabled, an incoming Far-End Fault pattern is
ignored.
It is strongly recommended to have switches used for substation automation that support the Far-End Fault feature,
especially when UR 7 redundancy Failover is selected for redundancy.
5.3.6.6 Parallel Redundancy Protocol (PRP)
The B90 is provided with optional PRP capability. This feature is specified as a software option at the time of
ordering. See the Order Codes section in chapter 2 for details.
The Parallel Redundancy Protocol (PRP) defines a redundancy protocol for high availability in substation automation
networks. It applies to networks based on Ethernet technology (ISO/IEC 8802-3) and is based on the second edition (July
2012) of IEC 62439-3, clause 4.
PRP is designed to provide seamless recovery in case of a single failure in the network, by using a combination of LAN
duplication and frame duplication. Identical frames are sent on two completely independent networks that connect source
and destination. Under normal circumstances both frames reach the destination and one of them is sent up the OSI stack
to the destination application, while the second one is discarded. If an error occurs in one of the networks and traffic is
prevented from flowing on that path, connectivity is provided through the other network to ensure continuous
communication. Take care when designing the two LANs, so that no single point of failure (such as a common power
supply) is encountered, as such scenarios can bring down both LANs simultaneously.
Figure 5-15: Example of parallel redundant network 5
PRP uses specialized nodes called doubly attached nodes (DANPs) for handling the duplicated frames. DANP devices have
an additional module, called a Link Redundancy Entity (LRE). LRE is responsible for duplicating frames and adding the
specific PRP trailer when sending the frames out on the LAN, as well as making decisions on received frames as to which
one is sent up the OSI stack to the application layer and which one is discarded. LRE is responsible for making PRP
transparent to the higher layers of the stack.
In addition, there is a second type of specialized device used in PRP networks, called RedBox, with the role of connecting
Single Attached Nodes (SANs) to a redundant network.
UR relays implement the DANP functionality. The RedBox functionality is not implemented.
The original standard IEC 62439-3 (2010) was amended to align PRP with the High-availability Seamless Redundancy (HSR)
protocol. To achieve this, the original PRP was modified at the cost of losing compatibility with the PRP 2010 version. The
revised standard IEC 62439-3 (2012) is commonly referred to as PRP-1, while the original standard is PRP-0. The UR relays
support PRP-1.
The relay implements PRP on two of its Ethernet ports, specifically Ports 2 and 3 of the CPU module. Use the previous
section (network port configuration) to configure PRP.

PRP is purchased as a separate option. If purchased (valid order code), PRP can be enabled in configuration through a
setting available on the network configuration menu, REDUNDANCY, which already has the capability of enabling failover
redundancy. The options on this setting must be changed to accommodate two types of redundancy: failover and PRP.
When REDUNDANCY is set to either failover or PRP, the ports dedicated for PRP (Ports 2 and 3) operate in redundant mode.
In this mode, Port 3 uses the MAC, IP address, and mask of Port 2.
5.3.6.7 IPv4 route table

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IPv4 ROUTE TABLE 1(6)
 IPv4 ROUTE TABLE  DEFAULT IPv4 ROUTE
  
 IPv4 NETWORK
  ROUTE 1

 IPv4 NETWORK
  ROUTE 6
A default route and up to six static routes can be configured.

The default route is used as the last choice when no other route towards a given destination is found.
 DEFAULT IPv4 ROUTE GATEWAY ADDRESS: Range: standard IPV4 unicast address format
  127.0.0.1
5  IPv4 NETWORK
 ROUTE 1  RT1 DESTINATION:
127.0.0.1
Range: standard IPV4 address format
RT1 NET MASK: Range: standard IPV4 subnet mask format

 255.0.0.0
RT1 GATEWAY: Range: standard IPV4 unicast address format

 127.0.0.1
Configure the network IP and subnet settings before configuring the routing settings.
Add and delete static routes

Host routes are not supported at present.
The routing table configuration is available on the serial port and front panel. This is a deliberate decision, to avoid loss of
connectivity when remotely configuring the B90.
By default, the value of the destination field is 127.0.0.1 for all static routes (1 to 6). This is equivalent to saying that the
static routes are not configured. When the destination address is 127.0.0.1, the mask and gateway also must be kept on
default values.
By default, the value of the route gateway address is 127.0.0.1. This means that the default route is not configured.
To add a route:
1. Use any of the static network route entries numbered 1 to 6 to configure a static network route. Once a route
destination is configured for any of the entries 1 to 6, that entry becomes a static route and it must meet all the rules
listed in the next section, General Conditions to be Satisfied by Static Routes.
2. To configure the default route, enter a default gateway address. Once a default gateway address is configured, it
must be validated against condition 2 of the General Conditions to be Satisfied by Static Routes, where the route
gateway must be on a connected network.
To delete a route:
1. Replace the route destination with the default loopback address of 127.0.0.1. When deleting a route, the mask and
gateway also must be brought back to default values.

2. Delete the default route by replacing the default gateway with the default value of 127.0.0.1.
General conditions to be satisfied by static routes

The following rules are validated internally:
• The route mask has IP mask format. In binary this needs to be a set of contiguous bits of 1 from left to right, followed
by one or more contiguous bits of 0.
• The route destination and mask must match. This can be verified by checking that
RtDestination and RtMask = RtDestination
Example of good configuration: RtDestination = 10.1.1.0; Rt Mask = 255.255.255.0
Example of bad configuration: RtDestination = 10.1.1.1; Rt Mask = 255.255.255.0
The following rules must be observed when you configure static routes:
• The route destination must not be a connected network
• The route gateway must be on a connected network. This rule applies to the gateway address of the default route as
well. This can be verified by checking that:
(RtGwy & Prt1Mask) == (Prt1IP & Prt1Mask) || (RtGwy & Prt2Mask) == (Prt2IP & Prt2Mask) || (RtGwy & Prt3Mask) == (Prt3IP
& Prt3Mask)
where
& is the bitwise-AND operator
== is the equality operator
|| is the logical OR operator
Routing behavior compared to previous releases

Prior to release 7.10, UR devices did not have an explicit manner of configuring routes. The only available route was the 5
default route configured as part of the network settings (port gateway IP address). This limited the ability to route to
specific destinations, particularly if these destinations were reachable through a different interface than the one on which
the default gateway was.
Starting with UR 7.10, up to six static network routes can be configured in addition to a default route. The default route
configuration was also moved from the network settings into the routing section.
The figure shows an example of topology that benefits from the addition of static routes.
Figure 5-16: Using static routes
Router1
Public network
.1
Router2
10.1.2.0/24 10.1.3.0/24
10.1.1.0/24
ML3000 ML3000 .1
EnerVista Software
P1 P2 P3
IP1/ IP2/ IP3/
.2 .2 MAC2 MAC3
MAC1
UR
859714A1.vsd
In the figure, the UR connects through the following two Ethernet ports:
• Port 1 (IP address 10.1.1.2) connects the UR to LAN 10.1.1.0/24 and to the Internet through Router1. Router1 has an
interface on 10.1.1.0/24 and the IP address of this interface is 10.1.1.1.

• Port 2 (IP address 10.1.2.2) connects the UR to LAN 10.1.2.0/24 and to the EnerVista software through Router2. Router2
has an interface on 10.1.2.0/24 and the IP address of this interface is 10.1.2.1.
The configuration before release 7.10 was as follows:
• PRT1 IP ADDRESS = 10.1.1.2
PRT1 SUBNET IP MASK = 255.255.255.0
PRT1 GWY IP ADDRESS = 10.1.1.1
PRT2 IP ADDRESS = 10.1.2.2
The behavior before release 7.10 was as follows. When sending packets to EnerVista, the UR noticed that the destination
was not on a connected network and it tried to find a route to destination. Since the default route was the only route it
knew, it used it. Yet EnerVista was on a private network, which was not reachable through Router1. Hence a destination
unreachable message was received from the router.
The configuration starting with release 7.10 is as follows:
• PRT1 IP ADDRESS = 10.1.1.2
PRT2 IP ADDRESS = 10.1.2.2
IPV4 DEFAULT ROUTE: GATEWAY ADDRESS = 10.1.1.1
STATIC NETWORK ROUTE 1: RT1 DESTINATION = 10.1.3.0/24; RT1 NET MASK = 255.255.255.0; and RT1 GATEWAY =
10.1.2.1
The behavior since release 7.10 is as follows. There is one added static network route to the destination 10.1.3.0/24, where
a computer running EnerVista is located. This static route uses a different gateway (10.1.2.1) than the default route. This
gateway is the address of Router2, which has knowledge about 10.1.3.0 and is able to route packets coming from the UR
5 and destined to EnerVista.
Show routes and ARP tables

This feature is available on the Web interface, where the main menu contains an additional Communications menu and
two submenus:
• Routing Table
• ARP Table
The tables outline the information displayed when the two submenus are selected.
Table 5-7: Routing table information
Field Description
Destination The IP address of the remote network to which this route points
Mask The network mask for the destination
Gateway The IP address of the next router to the remote network
Interface Interface through which the specified network can be reached
Table 5-8: IP ARP information

Field Description
IP Address The network address that corresponds to Hardware Address
Age (min) Age, in minutes, of the cache entry. A hyphen (-) means the address is local.
Hardware Address LAN hardware address, a MAC address that corresponds to network address
Type Dynamic or Static
Interface Interface to which this address mapping has been assigned

5.3.6.8 Modbus protocol

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL
 MODBUS PROTOCOL MODBUS SLAVE Range: 1 to 254 in steps of 1
  ADDRESS: 254
MODBUS TCP PORT Range: 0 to 65535 in steps of 1

 NUMBER(502): 502
The serial communication ports utilize the Modbus protocol, unless the port is configured for DNP or IEC 60870-5-103
operation. This allows the EnerVista UR Setup software to be used on the port. UR devices operate as Modbus slave
devices only.
For more information on the protocol, including the memory map table, see the UR Family Communications Guide.
MODBUS SLAVE ADDRESS — When using the Modbus protocol on the RS232 port, the B90 responds regardless of the
MODBUS SLAVE ADDRESS programmed. For the RS485 port, each device on the serial bus must have a unique slave address
from 1 to 254. Address 0 and addresses from 248 and up are reserved by the Modbus protocol specification, and so their
use here is not recommended. Address 0 is the broadcast address to which all Modbus slave devices listen. Addresses do
not have to be sequential, but no two devices can have the same address or conflicts resulting in errors occur. Generally,
starting at 1, set each device added to the link to use the next higher address. When using Modbus TCP/IP, the client must
use the programmed MODBUS SLAVE ADDRESS value in the Unit Identifier field.
MODBUS TCP PORT NUMBER — Modbus over TCP/IP can also be used on any of the Ethernet ports. The listening TCP port 502
is reserved for Modbus communications, and only in exceptional cases when MODBUS TCP PORT NUMBER is set to any other
port. The MODBUS TCP PORT NUMBER setting sets the TCP port used by Modbus on Ethernet. A MODBUS TCP PORT NUMBER of
0 disables Modbus over TCP/IP, meaning closes the Modbus TCP port. When the port number is changed to 0, the change
takes effect when the B90 is restarted. When it is set to 0, use the front panel or serial port to communicate with the relay.
Do not set more than one protocol to the same TCP/UDP port number, as this results in unreliable operation of
5
those protocols.
5.3.6.9 Protocol selection

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  PROTOCOL
 PROTOCOL SCADA PROTOCOL: Range: DNP 3.0, IEC 60870-5-104, IEC 60870-5-103
  DNP 3.0
MMS CONNECTION Range: 10 to 7200 in steps of 10

 TIMEOUT: 120 s
IEC61850 EDITION: Range: Edition1, Edition2

 Edition2
The PROTOCOL menu allows selection of one of the following protocols: DNP 3.0, IEC60870-104, or IEC60870-103.
SCADA PROTOCOL — This setting selects the SCADA protocol on which the unit communicates, among DNP3.0, IEC 60870-
104, and IEC 60870-103, with DNP being the default. Options depend on order code. For any change to take effect, restart
the unit.
MMS CONNECTION TIMEOUT — This setting specifies a time delay for the detection of network TCP connection lost. If there is
no data traffic on the TCP connection for greater than the time specified by this setting, the connection is terminated. This
frees up the connection to be re-used by a client. A setting of 10 seconds disables this timer. The TCP connection then is
managed by a standard TCP KeepAlive message sequence. These messages are transmitted every 20 seconds when there
is no MMS communication between the relay and the client. If there are no responses to the TCP KeepAlive messages, the
connection is closed. For any change to this setting to take effect, restart the unit. The change takes effect for a new
connection. For any existing open connection when the change is made, close and re-open the connection. Cycling power
to the relay also applies the new setting.
The table shows which of DNP 3.0, IEC 60870-5-104, IEC 60870-5-103, and IEC 61850 protocols are operational on the
RS232, RS485, and Ethernet ports. It shows all possible combinations of the PROTOCOL and DNP CHANNEL 1(2) PORT settings.

Table 5-9: Port and protocol combinations

PROTOCOL DNP CHANNEL 1(2) PORT RS232 RS485 Ethernet
setting settings
DNP Channel 1: Eth TCP Modbus Modbus DNP, Modbus, IEC 61850
Channel 2: Eth TCP
Channel 1: Eth TCP Modbus Modbus DNP, Modbus, IEC 61850
Channel 2: none
Channel 1: none Modbus Modbus DNP, Modbus, IEC 61850
Channel 2: Eth TCP
Channel 1: Eth UDP Modbus Modbus DNP, Modbus, IEC 61850
Channel 2: none
Channel 1: Eth TCP Modbus DNP DNP, Modbus, IEC 61850
Channel 2: RS485
Channel 1: Eth TCP DNP Modbus DNP, Modbus, IEC 61850
Channel 2: RS232
Channel 1: Eth UDP Modbus DNP DNP, Modbus, IEC 61850
Channel 2: RS485
Channel 1: Eth UDP DNP Modbus DNP, Modbus, IEC 61850
Channel 2: RS232
Channel 1: RS485 Modbus DNP DNP, Modbus, IEC 61850
Channel 2: Eth TCP
Channel 1: RS232 DNP Modbus DNP, Modbus, IEC 61850
Channel 2: Eth TCP
Channel 1: RS485 DNP DNP Modbus, IEC 61850
Channel 2: RS232
5 Channel 1: RS232
Channel 2: RS485
DNP DNP Modbus, IEC 61850
Channel 1: RS485 Modbus DNP Modbus, IEC 61850

Channel 2: none
IEC 104 Modbus Modbus IEC 104, Modbus, IEC 61850
IEC 103 Modbus IEC 103 Modbus, IEC 61850
IEC61850 EDITION — Switches between Editions 1 and 2 of the IEC 61850 protocol. Settings default with the change, except
GGIO1, GGIO2, GGIO4, and those for the graphical front panel. A message displays that a reboot is required, which can be
done using Maintenance > Reboot Relay Command.
5.3.6.10 DNP protocol

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL
 DNP PROTOCOL  DNP CHANNELS See below
  
DNP ADDRESS: Range: 0 to 65535 in steps of 1

 1
 DNP NETWORK See below

  CLIENT ADDRESSES
DNP TCP/UDP PORT Range: 0 to 65535 in steps of 1

 NUMBER(20000): 20000
DNP UNSOL RESPONSE Range: Enabled, Disabled

 FUNCTION: Disabled
DNP UNSOL RESPONSE Range: 0 to 60 s in steps of 1

 TIMEOUT: 5 s
DNP UNSOL RESPONSE Range: 1 to 255 in steps of 1

 MAX RETRIES: 10

DNP UNSOL RESPONSE Range: 0 to 65519 in steps of 1

 DEST ADDRESS: 1
DNP CURRENT SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP VOLTAGE SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP POWER SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP ENERGY SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP PF SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP OTHER SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,
 FACTOR: 1 100000, 1000000, 10000000, 100000000
DNP CURRENT DEFAULT Range: 0 to 100000000 in steps of 1

 DEADBAND: 30000
DNP VOLTAGE DEFAULT Range: 0 to 100000000 in steps of 1

 DEADBAND: 30000
DNP POWER DEFAULT Range: 0 to 100000000 in steps of 1

 DEADBAND: 30000
DNP ENERGY DEFAULT Range: 0 to 100000000 in steps of 1

 DEADBAND: 30000
 DNP PF DEFAULT
DEADBAND: 30000
Range: 0 to 100000000 in steps of 1 5
DNP OTHER DEFAULT Range: 0 to 100000000 in steps of 1
 DEADBAND: 30000
DNP TIME SYNC IIN Range: 1 to 10080 min. in steps of 1

 PERIOD: 1440 min
DNP MESSAGE FRAGMENT Range: 30 to 2048 in steps of 1

 SIZE: 240
DNP OBJECT 1 Range: 1, 2

 DEFAULT VARIATION: 2
DNP OBJECT 2 Range: 1, 2, 3

DNP OBJECT 20 Range: 1, 2, 5, 6




DNP OBJECT 30 Range: 1, 2, 3, 4, 5

DNP OBJECT 32 Range: 1, 2, 3, 4, 5, 7

DNP NUMBER OF PAIRED Range: 0 to 32 in steps of 1

 CONTROL POINTS: 0

DNP TCP CONNECTION Range: 10 to 7200 s in steps of 1

 TIMEOUT: 120 s
DNP EVENT TIME BASE: Range: UTC, LOCAL

 LOCAL
The Distributed Network Protocol (DNP) allows for the optimization of control and data acquisition between the equipment
in the substation and the central control center. The protocol is scalable; that is, it is designed to be compatible with the
latest high speed LAN technology yet still be implemented over slower speed serial links.
The DNP improves upon many master-slave protocols by improving overall communication performance requirements
and provides time-stamping with millisecond accuracy.
The B90 supports DNP version 3.0.
DNP is enabled when the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  PROTOCOL setting is set to DNP 3.0. The B90
can be used as a DNP slave device connected to multiple DNP masters (usually an RTU or a SCADA master station). Since
the B90 maintains two sets of DNP data change buffers and connection information, two DNP masters can actively
communicate with the B90 at one time.
DNP is not available using the USB port on the graphical front panel.
See the UR Family Communications Guide for more information on DNP.
The DNP Channels sub-menu is shown.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP CHANNELS
 DNP CHANNELS DNP CHANNEL 1 PORT: Range: NONE, COM1 - RS485, COM2 - RS485, FRONT
  NONE PANEL - RS232, NETWORK - TCP, NETWORK - UDP
DNP CHANNEL 2 PORT: Range: NONE, COM1 - RS485, COM2 - RS485, FRONT

5 NONE PANEL - RS232, NETWORK - TCP
The DNP CHANNEL 1 PORT and DNP CHANNEL 2 PORT settings select the communications port assigned to the DNP protocol
for each channel. Once DNP is assigned to a serial port, DNP is the only protocol running on that port; Modbus or IEC
60870-5-103 are disabled. If DNP is assigned to RS485, the protocol must be set to DNP on the serial port configuration as
well, for the change to take effect. When the DNP CHANNEL 1(2) PORT setting is set to “Network - TCP,” the channel 1(2) DNP
protocol can be used over TCP/IP on the Ethernet ports. When this value is set to “Network - UDP,” the DNP protocol can be
used over UDP/IP on channel 1 only. The "Front Panel - RS232" setting does not apply to the graphical front panel; when
selected the DNP client cannot establish a connection on a USB port.
For any change to take effect, restart the relay.
those protocols.
The DNP ADDRESS setting is the DNP slave address. This number identifies the B90 on a DNP communications link. Assign a
unique address to each DNP slave.
The B90 can specify a maximum of five clients for its DNP connections. These are IP addresses for the controllers to which
the B90 can connect. The settings follow.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP NETWORK CLIENT ADDRESSES
 DNP NETWORK CLIENT ADDRESS 1: Range: standard IP address
 CLIENT ADDRESSES  0.0.0.0

CLIENT ADDRESS 5: Range: standard IP address
 0.0.0.0
The DNP TCP/UDP PORT NUMBER setting is for normal DNP operation. To close the port, set the port number to 0. The change
takes effect when the B90 is restarted.

The DNP UNSOL RESPONSE FUNCTION is set to “Disabled” for RS485 applications since there is no collision avoidance
mechanism. The DNP UNSOL RESPONSE TIMEOUT sets the time the B90 waits for a DNP master to confirm an unsolicited
response. The DNP UNSOL RESPONSE MAX RETRIES setting determines the number of times the B90 retransmits an
unsolicited response without receiving confirmation from the master; a value of “255” allows infinite re-tries. The DNP
UNSOL RESPONSE DEST ADDRESS is the DNP address to which all unsolicited responses are sent. The IP address to which
solicited responses are sent is determined by the B90 from the current TCP connection or the most recent UDP message.
The DNP scale factor settings are numbers used to scale analog input point values. These settings group the B90 analog
input data into the following types: current, voltage, power, energy, power factor, and other. Each setting represents the
scale factor for all analog input points of that type. For example, if the DNP VOLTAGE SCALE FACTOR setting is set to “1000,”
all DNP analog input points that are voltages are returned with values 1000 times smaller (for example, a value of 72000 V
on the B90 is returned as 72). These settings are useful when analog input values must be adjusted to fit within certain
ranges in DNP masters. Note that a scale factor of 0.1 is equivalent to a multiplier of 10 (that is, the value is 10 times larger).
The DNP DEFAULT DEADBAND settings determine when to trigger unsolicited responses containing analog input data. These
settings group the B90 analog input data into the following types: current, voltage, power, energy, power factor, and other.
Each setting represents the default deadband value for all analog input points of that type. For example, to trigger
unsolicited responses from the B90 when any current values change by 15 A, the DNP CURRENT DEFAULT DEADBAND setting
is set to “15.” Note that these settings are the deadband default values. DNP object 34 points can be used to change
deadband values, from the default, for each individual DNP analog input point. For any change to take effect, restart the
relay. Whenever power is removed and re-applied to the B90, the default deadbands are in effect.
The B90 relay does not support power metering. As such, the DNP POWER SCALE FACTOR and DNP POWER DEFAULT
DEADBAND settings are not applicable.
The B90 relay does not support energy metering. As such, the DNP ENERGY SCALE FACTOR and DNP ENERGY DEFAULT
DEADBAND settings are not applicable.
5
The DNP TIME SYNC IIN PERIOD setting determines how often the Need Time Internal Indication (IIN) bit is set by the B90.
Changing this time allows the DNP master to send time synchronization commands more or less often, as required.
The DNP MESSAGE FRAGMENT SIZE setting determines the size, in bytes, at which message fragmentation occurs. Large
fragment sizes allow for more efficient throughput; smaller fragment sizes cause more application layer confirmations to
be necessary, which provides more robust data transfer over noisy communication channels.
Check the “DNP Points Lists” B90 web page to view the analog inputs and/or binary inputs points lists. This page
can be viewed with a web browser by entering the IP address of the B90 Ethernet port employed to access the B90
Main Menu, then by clicking the Device Information Menu item, then the DNP Points Lists item.
The DNP OBJECT 1 DEFAULT VARIATION to DNP OBJECT 32 DEFAULT VARIATION settings select the DNP default variation
number for object types 1, 2, 20, 21, 22, 23, 30, and 32. The default variation refers to the variation response when variation
0 is requested and/or in class 0, 1, 2, or 3 scans. See the DNP Implementation section in the UR Family Communications
Guide.
The DNP binary outputs typically map one-to-one to IED data points. That is, each DNP binary output controls a single
physical or virtual control point in an IED. In the B90 relay, DNP binary outputs are mapped to virtual inputs. However, some
legacy DNP implementations use a mapping of one DNP binary output to two physical or virtual control points to support
the concept of trip/close (for circuit breakers) or raise/lower (for tap changers) using a single control point. That is, the DNP
master can operate a single point for both trip and close, or raise and lower, operations. The B90 can be configured to
support paired control points, with each paired control point operating two virtual inputs. The DNP NUMBER OF PAIRED
CONTROL POINTS setting allows configuration of 0 to 32 binary output paired controls. Points not configured as paired
operate on a one-to-one basis.
The DNP TCP CONNECTION TIMEOUT setting specifies a time delay for the detection of dead network TCP connections. If
there is no data traffic on a DNP TCP connection for greater than the time specified by this setting, the connection is
aborted by the B90. This frees up the connection to be re-used by a client. For any change to take effect, restart the relay.

5.3.6.11 DNP / IEC 60870-5-104 point lists

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS
 DNP / IEC104  BINARY INPUT / MSP See below
 POINT LISTS   POINTS
 ANALOG INPUT / MME See below

  POINTS
Up to 256 binary and up to 256 analog input points for the DNP protocol, or the MSP and MME points for IEC 60870-5-104
protocol, can be configured. The value for each point is user-programmable and can be configured by assigning FlexLogic
operands for binary inputs / MSP points or FlexAnalog parameters for analog inputs / MME points.
The menu for the binary input points (DNP) or MSP points (IEC 60870-5-104) follows.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS  BINARY INPUT / MSP POINTS
 BINARY INPUT / MSP Point: 0 Range: FlexLogic operand
 POINTS  Off
Point: 1 Range: FlexLogic operand

 Off

Point: 255 Range: FlexLogic operand
 Off
Up to 256 binary input points can be configured for the DNP or IEC 60870-5-104 protocols. The points are configured by
assigning an appropriate FlexLogic operand. See the Introduction to FlexLogic section in this chapter for the range of
assignable operands.
5 Changes to the DNP / IEC 60870-5-104 point lists take effect when the B90 is restarted.
The menu for the analog input points (DNP) or MME points (IEC 60870-5-104) follows.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP / IEC104 POINT LISTS  ANALOG INPUT / MME
POINTS
 ANALOG INPUT / MME Point: 0 Range: any FlexAnalog parameter
 POINTS  Off
Point: 1 Range: any FlexAnalog parameter

 Off

Point: 255 Range: any FlexAnalog parameter
 Off
Up to 256 analog input points can be configured for the DNP or IEC 60870-5-104 protocols. The analog point list is
configured by assigning an appropriate FlexAnalog parameter to each point. See the FlexAnalog Parameters section in
Appendix A for the range of assignable parameters.
Changes to the DNP / IEC 60870-5-104 point lists take effect when the B90 is restarted.
The DNP / IEC 60870-5-104 point lists always begin with point 0 and end at the first “Off” value. Since DNP / IEC
60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored.
5.3.6.12 IEC 61850 protocol
The B90 is provided with optional IEC 61850 communications. This feature is specified as a software option at
the time of ordering. See the Order Codes section in chapter 2 for details.

The IEC 61850 settings are accessible in EnerVista software or a substation configuration language (SCL) generating tool.
The path is Settings > Product Setup > Communications > IEC 61850 or Settings > IEC 61850. The settings are not
accessible from the front panel of the device.
IEC 61850 messaging can form part of protection schemes. Consider IEC 61850 settings with the same criticality as
protection element settings. To ensure reliable performance of protection schemes utilizing IEC 61850 messaging,
route IEC 61850 traffic on a separate port from SCADA communications, or use redundant, independent ports, and
a high-speed network recovery method, such as PRP.
Overview
IEC 61850 is a series of international standards and technical reports applicable to power utility automation systems. It
includes semantics, abstract communication services, specific communication services, performance specifications,
network engineering guidelines, configuration description methodologies, and engineering processes. The standard
enables interoperability among intelligent electronic devices (IEDs) from different suppliers and interoperability among
software configuration tools from different suppliers. Interoperability in this case is the ability for IEDs to operate on the
same network or communication path sharing information and commands, and for configuration tools to understand
each other's configuration files.
The UR family supports a large subset of IEC 61850 features. These are detailed in the UR Family Communications Guide
and include the information model, GOOSE publish, GOOSE subscribe, buffered report server, unbuffered report server, and
Manufacturing Message Specification (MMS) query, read, write, and control services. In addition, the URs and their
EnerVista UR Setup software support IEC 61850 Substation Configuration Language (SCL) file import/export and merging.
Many settings of UR protection, control, and monitoring elements, that is to say elements that are not concerned with the
IEC 61850 protocol, can nevertheless be accessed via IEC 61850. These settings are documented elsewhere in this Settings
chapter. This section of the Settings chapter deals solely with the settings that configure the IEC 61850 protocol itself.
The maximum number of simultaneous clients supported by the UR family is five. 5
IEC 61850 Editions 1 and 2
This release supports IEC 61850 Edition 1 and Edition 2. The default is Edition 2.
Select IEC 61850 Edition 1 or Edition 2 under Settings > Product Setup > Communications > Protocol. Switching defaults
the IEC 61850 settings, except GGIO1, GGIO2, GGIO4, and those for the graphical front panel. A message displays that a
reboot is required, which can be done using Maintenance > Reboot Relay Command.
Edition 2.0 is used with certain modifications according to IEC/TR 61850-90-5. Only edition 2.0 61850 configuration tools
can interoperate with edition 2.0 devices, such as the UR 7.3x, 7.4x, or 7.6x release. When using Edition 2, the UR release
uses edition 2.0 SCL, which differs from edition 1.0 SCL. GSSE, fixed GOOSE, and fixed report services of Edition 1 are not
supported in Edition 2, and thus UR devices using these features have to be converted to configurable GOOSE to
communicate with a 7.3x, 7.4x, or 7.6x device.
When set to Edition 1
• The Test Flag in the Tx GOOSE message header is set to TRUE when the TEST MODE FUNCTION is set to Forcible or
Isolated
• The test flag in the received GOOSE message header is not validated
• Routable GOOSE is not supported
• The FlexLogic category does not display in the IEC 61850 panels in the EnerVista UR Setup software
• With SCL file import, for Edition 1 the IP address in the ConnectedAP element must match one IP address of the device,
while for Edition 2 one of the three IP addresses in the ConnectedAP element must match
The fields that display in the software depend on the Edition selected and the B90. Differences are noted in the sections
that follow. If required, consult the Model Implementation Conformance Statement (MICS) section of the UR Family
Communications Guide to understand what applies to your setup.

EnerVista setup for IEC 61850

The EnerVista UR Setup software provides the interface to configure B90 settings for the IEC 61850 protocol. This section
describes this interface. The software also supports import/export and merging of IEC 61850 Substation Configuration
Language (SCL) files as documented in the UR Family Communications Guide.
The IEC 61850 protocol configuration settings cannot be accessed through the UR front panel and are instead accessible
with the EnerVista software, via MMS query, read, and write services, or via 61850 SCL file transfer. Accordingly, whereas
other settings are presented in this manual as they appear on the front panel, IEC 61850 settings are presented as they
appear in the software. See the UR Family Communications Guide for MMS and SCL access. Note that if you update the IEC
61850 settings in the EnerVista software by writing to them by MMS while the corresponding IEC 61850 panel is open in
EnerVista, you need to close then open the panel in EnerVista for the correct readings to display.
IEC 61850 protocol configuration settings are accessed through software panels that are selected either in the Online
Window area (see figure) or the Offline Window area in the EnerVista software.
The EnerVista software also includes an interface that is compatible with firmware versions 5.0 to 7.2 to configure
subscribers. Use the Simplified GOOSE Configurator in the Offline Window area.
Figure 5-17: IEC 61850 protocol panel in EnerVista software (Edition 2)
The IEC 61850 window is divided into a navigation pane on the left and a settings panel on the right. You expand and click
an option on the left to display its panel on the right. The following figure shows an example for Server Configuration. The
SETTING column contains the names of the settings, and the PARAMETER column is used to enter the settings. Hovering
the mouse over a setting name displays a tool-tip showing the 61850 information model name of the setting or its location
in SCL files.

Figure 5-18: IEC 61850 panel (Edition 2)
Opening the IEC 61850 window while online causes the UR Setup software to retrieve and import an SCL file from the B90.
This System Configuration Description (SCD) file contains all the settings in the UR at the time of the file request, both those
that are mapped into the IEC 61850 information model (that is, the "public" sections) and those that are not in the model
(that is, the "private" section). The UR EnerVista Setup software imports all of these settings into the current session, not just
those in the IEC 61850 window. To avoid loss of any unsaved setting changes made in other panels during the current
session, all other panels for the B90 must be closed before the IEC 61850 panel can be opened, and the software prompts 5
for this when applicable. Panels for other devices can be open concurrently to facilitate parameter coordination.
When CyberSentry security is enabled, editable settings depend on the user role logged in. For example, an Administrator
and Engineer can change settings. If prompted for a "Settings password," it means the Administrator or Engineer
password.
The Restore button restores settings in the window to their last saved values. The Default button reverts settings in the
window to factory default values or Oscillography, Data Logger, or FlexLogic Equation Editor pre-configured values. The
Reset button reverts all IEC 61850 settings to the factory default values, not just the current window. (In other settings
windows, the button reverts settings in the window to factory default values.)
When a setting is enabled, its panel continues to read Disabled until relaunched. There is no polling capability to update
automatically the IEC 61850 readings, so the panel needs to be closed then opened for the correct status to display. Good
practice is to close any panel not in use because changes being made by other users too are reflected only upon relaunch
of the panel.
Some of the IEC 61850 settings use floating point data, which guarantees accurate representation of real numbers up to
seven digits. Numbers with more than seven digits are approximated within a certain precision. This can result in
differences between what is entered and what is saved, and for example results in differences shown on a settings
comparison report.
Create CID and settings files

When the Save button is clicked in the online IEC 61850 window, UR Setup software prepares a configured IED description
(CID) file containing all the settings of the UR and sends the CID file to the B90. Upon receipt, the B90 checks the CID file for
correctness, going out of service, then back into service when the CID file is accepted. The software displays a message
when the B90 is running the new settings, confirming successful transfer. This process can take a minute or so due to the
amount of processing required by the software and the B90.
When the Save button is clicked in the offline IEC 61850 window, UR Setup software saves to local storage, for example the
hard drive, a .urs file containing all settings of the UR.

View IID/CID files

The file types are described as follows:
• CID — Configured IED description file — Settings sent to the UR (may or may not contain the present settings)
The IID file type applies to IEC 61850 Edition 2 only.
IID and CID files are viewable. For example, after modifying settings in the IEC 61850 panels and clicking Developer IID/
CID Viewer in the software, a CID file generates and an SCL Viewer shows the updated CID file content. There are no edit
or save functions; use instead the Back Up and Restore Settings instructions later in this document to save the files.
Searches are case insensitive.
Figure 5-19: View CID settings file (Edition 2)
Server configuration
The Server Configuration panel contains IEC 61850 settings relevant to the server functions of the IED implementation.
The path is Settings > Product Setup > Communications > IEC 61850 > Server Configuration.
The following settings are available, where <iedName> is a syntactic variable representing the present value of the IED
NAME setting.
IED NAME
Range: 1 to 58 VisibleString characters
Default: TEMPLATE
The value entered sets the IED name used by IEC 61850 for the B90. An IED name unique within the network must be
entered for proper operation. Valid characters are upper and lowercase letters, digits, and the underscore (_) character.
The first character must be a letter.
The IED NAME and the Product LD inst name comprise the <LDName> for a product. The longest LD inst are "Master"
and "System" at six characters, with Master being fixed and the others configurable with the configurable Logical device
feature. So the IED NAME needs to be restricted to 58 characters to meet a 64 character limit.
Access Point
Range: S1, S2, S3
Default: S1
This setting applies to IEC 61850 Edition 1. It is the subnetwork.

Location
Range: 0 to 255 ASCII characters
Default: Location
The value entered sets the value of the data attribute <LDName>/LPHD1.PhyNam.location. This data attribute is
provided by the protocol to allow the user to declare where the equipment is installed.
Latitude
Range: -90.000 to 90.000 degrees in steps of 0.001 degree
Default: 0.000 deg
The value entered sets the value of the data attribute <LDName>/LPHD1.PhyNam.latitude. This data attribute is provided
by the protocol to declare the geographical position of the device in WGS84 coordinates -latitude. Negative values
indicate a southern latitude. WGS refers to the world geodetic system, which is used in global positioning systems (GPS),
and 84 is the current version of the standard.
Longitude
Range: -180.000 to 180.000 degrees in steps of 0.001 degree
Default: 0.000 deg
The value entered sets the value of the data attribute <LDName>/LPHD1.PhyNam.longitude. This data attribute is
provided by the protocol to declare the geographical position of the device in WGS84 coordinates -longitude. Negative
values indicate a western longitude.
Altitude
Range: 0 to 10,0000 m in steps of 1 m
Default: 0 m
The value entered sets the value of the data attribute <LDName>/LPHD1.PhyNam.altitude. This data attribute is provided
by the protocol to declare the geographical position of the device in WGS84 coordinates - altitude.
Prefix for GGIO1
5
Range for Edition 2: 0 to 11 VisibleString characters
Default:
This setting sets the LN Prefix of the FlexLogic operand interface logical node GGIO1 that is described in the GGIO1
section later. Valid characters are upper and lowercase letters, digits, and the underscore (_) character. The first
character must be a letter. UR Setup software does not allow entry of a prefix that duplicates any other GGIO1 prefix
that is used by the product, such as ConIn and ConOut.
Prefix for GGIO2
Default:
This setting sets the LN Prefix of the Virtual Inputs Interface logical node GGIO2 that is described in the GGIO2 section
later. Valid characters are upper and lowercase letters, digits, and the underscore (_) character. The first character must
be a letter. UR Setup software does not allow entry of a prefix that duplicates any other GGIO2 prefix that is used by the
product.
Prefix for GGIO4
Default:
This setting sets the LN Prefix of the FlexAnalog operand interface logical node GGIO4 that is described in the GGIO4
section later. Valid characters are upper and lowercase letters, digits, and the underscore (_) character. The first
character must be a letter. UR Setup software does not allow entry of a prefix that duplicates any other GGIO4 prefix
that is used by the product.

LLN0.Mod.ctlModel
Range: status-only, direct-with-normal-security, sbo-with-normal-security
Default: sbo-with-normal-security
This setting specifies the control service that clients must use to control the TEST MODE FUNCTION of the B90. An "on"
control to <LDName>/LLN0.Mod changes TEST MODE FUNCTION to Disabled, an "on-blocked" control changes it to
Forcible, and a "test/blocked" changes it to Isolated.
Configuration Type
Range: G2, E3-2.0
Default: G2
This setting is read only. It specifies the method used to describe GOOSE subscription configuration in SCL. See the UR
Family Communications Guide for details. In the G2 mode, the CID file contains IED elements for IEDs subscribed to by
this IED containing GOOSE subscription information. In the E3 2.0 mode, the CID file has only one IED element and
GOOSE subscription information is coded in data objects in the standard LGOS logical node used to monitor reception of
the subscribed GOOSE. UR 7.30 or later accepts either mode. The set value is for the entire EnerVista installation and is
preserved between sessions. To change this global field, click File > Preferences and access the IEC 61850 panel; you do
not need to be connected to the device.
Logical devices
The Logical Devices panel contains IEC 61850 settings relevant to the configurable logical devices feature, wherein logical
device naming can be reconfigured and logical nodes re-assigned.
The path is Settings > Product Setup > Communications > IEC 61850 > Logical Devices.
Figure 5-20: Default IEC 61850 Logical Devices panel with devices middle and nodes right (Edition 2)
To configure logical devices and nodes:

1. Right-click an entry and edit an existing device, add a new one, or move a logical node. The rest of this section
explains the window and how to perform these actions.
The default logical device categories are as follows:

• Master — Communications, including GOOSE, reports, Remote I/O, Virtual Inputs, Modbus, DNP, and setting group
control
• System — Power system devices: breakers, switches, CTs, VTs, and so on, including interfaces to these, such as AC
inputs, contact I/O, transducer I/O, HardFiber I/O
• Prot — Protection and protection-related functions
• Ctrl — Control and monitoring functions
• Meter — Metering and measurement functions

• Gen — FlexLogic, Virtual Outputs, non-volatile latches, FlexElements, recording (for example oscillography), security,
front panel, clock
For the Master logical device, the following logical nodes have fixed assignment:
• The LLN0 in the Master logical device, which includes setting group, GOOSE and report control blocks, and datasets
• LPHD1 — Models common issues for physical devices
• GGIO1 — For unmapped FlexLogic operands
• GGIO2 — For Virtual Input control
• GGIO3 — For RxGOOSE Inputs
• GGIO4 — For unmapped FlexAnalog operands
• LGOS logical nodes — For GOOSE subscription
The Logical Devices panel has middle and right panes. The middle pane has a list of the instantiated logical devices in the
sequence that they appear in SCL, with one device selected. The right pane has a list of the logical nodes presently
assigned to the selected logical device in lexicographic order by logical node name.
In the middle pane logical devices are shown with their product-related name, followed in brackets by their function-
related ldName, and followed by the value of their confRev. In the following example, by right-clicking and editing, the
Protection logical device has been set to instance name "Prot", the function-related name "Feeder1Prot" and the
configuration revision "2016-03-07 08:46." The text is clipped on the right if the line is longer than the available width. The
next paragraphs explain how to do this setup.
Figure 5-21: Protection logical node selected
Right-clicking a logical device displays the menu that allows insertion of a new logical device immediately below the
selected one, deletion of the selected logical device, or editing the selected logical device's parameters. The insert option is
disabled and greyed-out if there are already 16 logical devices instantiated. The delete option is disabled and greyed-out if
the selected logical device is Master or it contains any logical nodes other than LLN0.

Figure 5-22: Menu for logical node
If the insert option is selected, or the edit option is selected for other than the Master logical device, a logical device
parameters edit dialog opens.
Figure 5-23: Insert new logical node (Edition 2)
If the edit option is selected for the Master logical device, the Product LD inst name setting is not editable.

Figure 5-24: Edit logical node
When the Ok button is clicked, the entered values for Product LD inst name and Functional ldName are checked for
uniqueness within the UR, and they are updated in the pane.
The settings are explained as follows, where <iedName> is a syntactic variable representing the present value of the IED
NAME setting. When adding or editing a logical device entry, these are the fields that need to be completed.
Customized logical nodes are not saved in the URS file.
Product LD inst name

Default: as per the following table 5
Each logical device has this setting. The value is fixed at "Master" in the first logical device and configurable in all others.
Valid characters are upper and lowercase letters, digits, and the underscore (_) character. The first character must be a
letter. The entered value sets the logical device inst name. Each logical device inst name is required to be unique within
the device, and it cannot be blank. Also, if the corresponding functional ldName setting is blank, the concatenation of the
IED name and the logical device inst name must form an LDName that is unique within the network for proper operation.
It is recommended that the length of the IED NAME plus the length of this setting be not greater than 64 to respect the
requirements of IEC 61850 7 2:2010 22.2 for LDName.
The factory default configuration is for six logical devices with Product LD inst name settings and logical node
assignments as per the following table.
Table 5-10: Factory default logical nodes
Default logical Contains logical nodes modeling...
device inst name
Master communications, including GOOSE, reports, Remote I/O, Virtual Inputs, Modbus, DNP, and so on.
(root logical device; Setting group control.
name is fixed) This is the root logical device.
To comply with IEC 61850 7 1 Ed2 clause 6.4.5.1, all group L logical nodes (logical nodes with class names
begin with "L"), except LLN0, belonging to this IED are in this logical device.
Protection (Prot) protection functions
Control (Ctrl) control and monitoring functions
System power system devices: breakers, switches, CTs, VTs, and so on, including interface to these such as AC inputs,
contact I/O, transducer I/O, HardFiber I/O
Metering (Meter) metering and measurement, including Signal Sources
General (Gen) FlexLogic, virtual outputs, non-volatile latches, FlexElements, FlexMath, recording (for example oscillography),
security, front panel, clock

Functional ldName
Default: empty string
Each logical device has this setting. The value is configurable in all logical devices. Valid characters are upper and
lowercase letters, digits, and the underscore (_) character. If the number of characters entered is greater than zero, the
setting sets the value of the function-related name used in communications. If an ldName is entered, it must form an
LDName that is unique within the network for proper operation. The standard recommends choosing this name
according to IEC 81346-1. If the number of characters entered is zero, no function-related name is defined.
Throughout the remainder of this IEC 61850 section, <LDName> is a syntactic variable representing the present
LDName of the master logical device. In other contexts LDName can refer to some other logical device. Depending
on its context, <LDName> can be a product-related name or a function-related name.
configRev
Range: 0 to 255 ASCII characters
Default:
This data attribute is provided by the protocol to declare changes to the semantic of the data model of the UR. The intent
is that the user changes Master configRev each time that the semantic or data model changes, so that clients can
readily detect the change. A semantic change is a logical node getting a new semantic use; for example, an instance of
logical node CSWI is now serving a different physical switch, or an instance of a logical node PDIS is now used for
another zone. A data model change is a change in the presence of logical nodes, data objects, data attributes, or
instance names.
The scope of Maser configRev is the entire relay configuration, as the Master logical device is the root logical device.
Similar settings are provided for the other logical nodes; the scope of these other configRev settings is limited to the
5 corresponding logical device configuration.

paramRev
Range: -2,147,483,648 to 2,147,483,647
Default: 0
The configurable data attribute paramRev has a scope that includes the entire device, and thus is modified whenever
any setting in the device changes. The UR increments the value of paramRev by one whenever one or multiple setting
changes occurs in one Modbus write request by any means (front panel, Modbus, or MMS) other than by SCL file
download. Incrementing occurs whether or not the setting is represented in the information model. When a UR device or
EnerVista UR Setup accepts an SCL file, paramRev is set to the value in that SCL file. When EnerVista UR Setup changes
one or more settings, and prepares an SCL file, it increments paramRev to the next higher multiple of 10 000.
Each logical device has a name: LDName. (Note the upper case LD.) LDName has both a product-related form and
a function-related form as per IEC 61850 6:2009 8.5.3.
SCL files invariably use the product-related form of LDName. The product-related form is the concatenation of the
IED name of the device and the individual logical device's inst name. The IED name is the value of the "IED NAME"
setting on the Server Configuration panel, and the logical device inst names are each the value of the
corresponding "Product LD inst name" setting here. The "Product LD inst name" of the first logical device is fixed at
"Master".
Communications use the function-related form of LDName if a function-related name is defined, otherwise
communications use the product-related name. The function-related name is the value of the corresponding
"Functional ldName" setting if this setting is not empty, if empty the function-related name is not defined.
In SCL, the function-related name is specified by the LDevice element attribute ldName (note the lower case ld).
Absence of this attribute indicates the function-related name is not defined. In SCL the product-related name is
specified by the name attribute of the IED element and the inst attribute of the LDevice element.
In the right pane, logical nodes assigned permanently to the Master logical device and LLN0 in all logical devices are
greyed-out as shown earlier. These are not movable. Any other logical node can be dragged to any of the logical devices in
the middle pane, which causes that logical device to be re-assigned to that logical device. Right-clicking a logical node

device displays a menu that lists the logical devices that this logical node can be moved to. Clicking one of these re-assigns
the logical node. Other common keyboard and/or mouse action can be used to select one or more logical nodes and move
the selected nodes together.
Figure 5-25: Move logical node (Edition2)
GOOSE
The path is Settings > Product Setup > Communications > IEC 61850 > GOOSE.
Support for Routable GOOSE

5
Routable GOOSE (R-GOOSE) is supported in firmware release 7.4 and later for IEC 61850 Edition 2. Routable GOOSE allows
UR and other devices to be located in separate networks. Encryption/decryption of messages is performed by a separate
gateway device. Messages are routed using a separate router, using IP addresses.
Note the following behavior:
• A v7.4 device can send an R-GOOSE message to another v7.4 device when both have R-GOOSE active as the protocol
• A v7.4 device can send a GOOSE message to another v7.4 device when both have GOOSE active as the protocol
• A v7.4 device cannot send an R-GOOSE message to non-R-GOOSE devices, such as v7.3 or v5.9 UR device
• UR devices with firmware below v7.3 can send a GOOSE message to a v7.4 device that has GOOSE as the active
protocol
R-GOOSE is available through the IEC 61850 software option. If R-GOOSE security is required, the CyberSentry
software option also must be purchased.
TxGOOSE
IEC 61850 GOOSE is an efficient method for simultaneous high-speed delivery of generic substation event information by a
publishing device to more than one subscribing device. A TxGOOSE is a UR element implementing a single IEC 61850
GOOSE message publishing service. The subscribing function in URs is performed by RxGOOSE elements, as described in
the next section. Each UR with IEC 61850 order code options has 16 TxGOOSE elements. Each TxGOOSE can either use the
original format specified in IEC 61850 8 1:2011 or the routable GOOSE (R-GOOSE; IEC 61850 Edition 2) format specified in
IEC TR 61850-90-5:2012. Each TxGOOSE element can publish the values of up to 64 attributes of the IEC 61850 nodes in the
UR.

Published TxGOOSE messages configured in the EnerVista UR Setup software can be subscribed by and the published
operand values understood by other UR devices. Furthermore, they can be subscribed to and understood by any device of
any manufacturer that implements the IEC 61850 edition 1.0 or 2.0 GOOSE subscription mechanism. The messages are
published with a multicast address so that the network sends the messages to all devices; any number of devices that
want to subscribe can.
For wide area protection, control, and monitoring schemes, R-GOOSE wraps the proven original format GOOSE in IP/UDP to
multicast (or unicast) the data over a Wide Area Network (WAN). Sample applications are Wide area Remedial Action
Scheme (RAS) and Under Voltage/ Frequency Load Shedding Schemes (UVLS/UFLS). R GOOSE uses IGMPv3 (Internet Group
Management Protocol version-3, RFC 3376) for multicasting.
The entities whose values are published in GOOSE messages are known as members. The members are itemized in an
ordered list known as a data set. Each TxGOOSE can use any one of the configured data sets. (See the DataSets section
later for details.) The performance of a TxGOOSE is determined by its dataset. Booleans in fast GOOSE datasets are
designed for the TT6 transfer time class (3 ms), while Booleans in the Normal datasets are designed for the TT3 class (100
ms). Due to the significant amount of CPU time required to compose a TT6 TxGOOSE message and the limited amount of
time allowed by the TT6 class, at most four of these can be configured in a given UR. So only four fast GOOSE are allowed
to be configured, and the UR software has a check to disallow the use of more than four fast datasets in GOOSE. If six fast
datasets are configured outside of UR software and the file sent directly to the relay, the relay rejects the file. The design
does allow six fast datasets to be used in report control blocks, which allows fast scanned data in reports.
Each enabled TxGOOSE transmits its message whenever a value change is detected in one or more of its members. If the
changed value is a Boolean in a fast dataset, then the change detect occurs in the TT6 detection time of 3 ms or less. If the
member is an analog value in a fast dataset, the change detect occurs in theTT3 time of 100 ms. In Normal GOOSE
Datasets, change detection for all dataset members occurs in the TT3 time of 100 ms. To guard against the possibility that
such a message is lost in the network before it reaches all subscribers, the message is quickly retransmitted several times.
To allow subscribers to verify that their link to the publisher and the publisher itself are healthy, each message is also
5 retransmitted periodically even while the values are unchanging. These latter messages are known as heartbeat
messages, while the former are known as event messages. Heartbeat messages also provide means for a subscriber
newly online to receive the published values in the absence of an event.
The details of TxGOOSE message construction are contained in the UR Family Communications Guide. Knowledge of these
details is not required to configure GOOSE.
The UR does not implement the Fixed-Length encoded GOOSE messages option specified in IEC 61850-8-1:2011 clause
A.3; the UR always uses the ASN.1 Basic encoding rules (as specified in ISO/IEC 8825-1) as specified in IEC 61850 edition 1.0
and as optional in IEC 61850 edition 2.0.
Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > TxGOOSE > TxGOOSE1 to access the
settings for the first TxGOOSE. The settings and functionality for the others are similar.

Figure 5-26: IEC 61850 TxGOOSE panel (Edition 2)
5
A data set needs to be set up and selected in the TxGOOSEx DatSet field for all content to display.
When saving changes, when a "dataset member is empty" message displays, you need to set the member in the bottom
right of the window.
TxGOOSE1 MODE
Range for Edition 2: Disabled, GOOSE, R-GOOSE
Range for Edition 1: Disabled, GOOSE
Default: Disabled
When set to Disabled, TxGOOSE1 messages are not published. When set to GOOSE, TxGOOSE1 messages are published
in IEC 61850 8 1:2011 GOOSE format. When set to R-GOOSE, TxGOOSE1 messages are published in Routable GOOSE
format according to IEC 61850 90-5, and the TxGOOSE1 DST MAC address is set to 00 00 00 00 00 00 and cannot be
changed.
TxGOOSE1 GoCB name
Range: 0 up to 32 VisibleString characters
Default: GoCB01
The entered value sets the GOOSE control block (GoCB) name value for TxGOOSE1.
An ObjectReference to the control block, which consists of the concatenation of the string "<LDName>/LLN0." and the
control block name, is published in the gocbRef field of TxGOOSE1 messages and is used by subscribers to discriminate
TxGOOSE1 messages from other GOOSE messages. <LDName> is a syntactic variable that is set to the value of setting
Master functional ldName if one or more characters have been entered to that setting, otherwise the value of setting IED
NAME suffixed with "Master".

TxGOOSE1 GoID
Default: TxGOOSE1
The entered value sets the goID value published in TxGOOSE1 messages, and can be used by subscribers to discriminate
the TxGOOSE1 messages from other GOOSE messages. Special characters are not allowed, such as <, >, &, ’, and ".
TxGOOSE1 DatSet
Range: None, TT6DataSet1,TT6 DataSet2, … TT3DataSet01,TT3 DataSet02, …
Default: None
This setting selects the published data set using the UR Setup software designator for the data set. If None is selected,
no TxGOOSE1 messages are sent.
The IEC 61850 name of the data sets are configured in the Datasets panel, as described later.
Some datasets are designed for the TT6 transfer time class (3 ms), while others are designed for the TT3 class (100 ms).
The performance of a TxGOOSE is determined by its dataset. Use TT6 datasets for trips and blocking applications, TT3
datasets for slow automatic interactions. The 61850 name of the datasets are configured in the Datasets panel.
An ObjectReference to the data set, which consists of the concatenation of the string "<LDName>/LLN0." and the data
set name, is published in the datSet field of TxGOOSE1 messages and can be used by subscribers to discriminate
TxGOOSE1 messages from other GOOSE messages. <LDName> is a syntactic variable that is set to the value of setting
Master functional ldName if one or more characters have been entered to that setting, otherwise the value of setting IED
NAME suffixed with "Master".
To configure a DataSet, select it at the top of the window from the drop-down list. In the lower part of the window, drag
and drop configuration items to the right side. Dataset members configured here affect other Report or TxGOOSE
control blocks that use the same DataSet.
5 The performance of the TxGOOSE is determined by the performance of the selected dataset. When the selection is
TT3DataSet01, TT3DataSet02, … it is possible that transient events can be missed.
TxGOOSE1 DST MAC
Range: any 12 digit hexadecimal number
Default: 01-0C-CD-01-00-00
When the TxGOOSE1 MODE setting is R-GOOSE, the TxGOOSE1 DST MAC address is set to 00 00 00 00 00 00 and cannot be
changed. Otherwise, the value entered here sets the Ethernet destination Media Access Control (MAC) address in
published TxGOOSE1 messages. As the standard requires that the address have the multicast bit set TRUE, that is to say
the second digit is set to an odd number, messages transmitted have the multicast bit set TRUE no matter its value in
this setting.
The destination MAC address can be used by the network to restrict message delivery to selected devices that need to
receive them, reducing network load. This address also can be used by hardware in receiving devices to filter out
messages that are of no interest to them, reducing processor burden. Different filtering algorithms are implemented by
different devices. The standard recommends that the algorithm used by hardware of the receiving device be considered
when assigning destination multicast addresses.
Subscribers can use this address to discriminate TxGOOSE1 messages from other GOOSE messages.
TxGOOSE1 VLAN PRIORITY
Range: 0, 1, 2, 3, 4, 5, 6, 7, 5-4, 6-4, 6-5, 7-4, 7-5, 7-6
Default: 4
When the value entered is 0, 1, 2, 3, 4, 5, 6, or 7, the User Priority value in the IEEE 802.1Q VLAN tag included in published
TxGOOSE1 messages is set to that value. When one of the two-digit values is entered, the dynamic priority feature is
selected: the first event message has the User Priority value of the first digit, and User Priority is decremented in each
following message until reaching the value of the second digit. For instance, if the selected value is 7-5, then the User
Priority values in successive messages beginning with the message triggered by an event is 7, 6, 5, 5, 5, 5, 5, and so on.
Do not make a dynamic priority selection when standard behavior is required.
Network devices can forward a message with a higher priority value before a message with a lower priority value, which
speeds delivery of high-priority messages in heavily loaded networks. The standard recommends that higher-priority
messages, such as GOOSE, have priority values in the range of 4 to 7.

TxGOOSE1 VLAN ID
Default: 0
The value entered sets the VID value in the IEEE 802.1Q VLAN tag included in published TxGOOSE1 messages. VID can be
used by network devices to direct messages to only selected devices, reducing network burden. VID values of 0 and 1
are assigned by IEEE 802.1Q to other functions and are not to be used for GOOSE.
TxGOOSE1 ETYPE APPID
Default: 0
The value entered sets the APPID value in published GOOSE messages and can be used by subscribers to discriminate
TxGOOSE1 messages from other GOOSE messages.
The standard reserves the value range 0 to 16383 for GOOSE Type 1 (Fast messages), and reserves the value range
32768 to 41151 for GOOSE Type 1A (Trip messages). Some subscribers can process messages in the Type 1A range
faster than messages in the Type 1 range. The standard reserves the default value (0) to indicate lack of configuration.
The standard strongly recommends unique, source-orientated APPIDs within a given system.
TxGOOSE1 CONFREV
Default: 1
The entered value sets the confRev value in published GOOSE messages and can be used by subscribers to discriminate
TxGOOSE messages of the expected configuration revision from messages of a different revision. The standard requires
that CONFREV be incremented each time the members or the order of the members published is changed. The standard
states that the value of 0 is reserved.
TxGOOSE1 RETRANS TIME
Range: 0 to 100 ms in steps of 1 ms 5
Default: 4 ms
If the entered time is non-zero, when a member value change is detected, four event transmissions are sent, then
heartbeat transmissions resume. The interval between the first and second event transmissions, and between the
second and third, is the time set here. The interval between the third and the fourth event transmission is double the set
time. If the entered time is zero, only a single event transmission occurs, then heartbeat transmissions resume.
TxGOOSE1 TIME TO LIVE
Range: 1 to 60 s in steps of 1 s
Default: 60 s
The value entered sets the timeAllowedtoLive value in published TxGOOSE1 messages. The standard requires
subscribers to assume a failure has occurred when another TxGOOSE1 message is not received within the published
timeAllowedtoLive time.
Base this setting on the TxGOOSE UPDATE TIME and the tolerable number of contiguous message delivery misses. For
example, if the heartbeat time is 10 s, and missing up to three successive messages is tolerable, make the setting
10 * 3 + 1 = 31 s. The extra second is to ensure that arrival of the third heartbeat transmission beats the
timeAllowedtoLive timer.
In the imported CID file, if the TxGOOSE1 TIME TO LIVE is greater than 60 seconds, clamp the setting value to 60 seconds
and an information log is provided in SCL log.
TxGOOSE1 UPDATE TIME
Range: 1 to 59 s in steps of 1 s
Default: 30 s
This setting specifies the time interval between heartbeat messages, meaning messages that are sent periodically while
no events are detected.
TxGOOSE1 PORT ASSIGNMENT
Range: Disabled, Port-1; Port-2; Port-3; Ports-1,2; Ports-2,3; Ports-1,3; Ports-1,2,3
Default: Ports-1, 2, 3
This setting applies to IEC 61850 Edition 2.

This setting specifies the Ethernet ports for transmission of TxGOOSE1. When set to disabled, TxGOOSE1 messages are
not transmitted on any port no matter the state of GoEna. When set to Port-1, TxGOOSE1 is published over Ethernet
Port-1 only; while selecting Ports-1, 3 option, the same TxGOOSE1 is published to both Ports 1 and 3; and similarly if set
to Ports-1, 2, 3, all ports publish TxGOOSE1.
When setting PRT2 REDUNDANCY to Failover or to PRP, the TxGOOSE 1 port assignment needs to be set to ports 2
and 3 (Ports-2,3).
Also, Port 3 configuration in the CID file is ignored. The Port 3 ConnectedAP elements has no meaning, as ports 2
and 3 use the port 2 MAC address, IP address, and mask.
R-TxGOOSE1 IP CLASS
Default: 46
When the TxGOOSE1 MODE setting is other than R-GOOSE, the value of this setting is not used. Otherwise this setting
selects the IPv4 Differentiated Services Code Point-DSCP (formerly called TypeOfService-TOS) value. This value provides
priority routing, when supported in the routers. The default value is for Expedited Forwarding (101110B, 46 or 2EH).
R-TxGOOSE1 DST IP
Range: 0.0.0.0 to 255.255.255 in steps of 1
Default: 224.0.0.0
When the TxGOOSE1 MODE setting is other than R-GOOSE, the value of this setting is not used. Otherwise this setting
specifies destination IP address for the R-TXGOOSE1 that is entered in Standard IPV4 address format. The destination IP
5 address needs to be a valid multicast or unicast IP address. The value specified in this setting is mapped to IPv4 header
32 bit field for Destination IP Address while publishing R-GOOSE1.
The default IP address 224.0.0.0 is reserved, and hence not a valid multicast IP address.
The source IP address is that of the UR port from which the R-GOOSE messages are transmitted.
R-TxGOOSE1 SECURITY
Range: None, Signature, SignatureAndEncryption
Default: None
This setting specifies level of security (authentication/encryption) used for TxGOOSE1. None specifies no security
mechanisms are to be used. Signature specifies only signature (no encryption) is to be used. SignatureAndEncryption
specifies that both signature and encryption are to be used.
RxGOOSE
Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > RxGOOSE > RxGOOSE Messages.
IEC 61850, GOOSE is an efficient method for simultaneous high-speed delivery of the same generic substation event
information by a publishing device to more than one subscribing device. An RxGOOSE is a UR element implementing a
single IEC 61850 GOOSE message subscribing service. The publishing function in URs is performed by TxGOOSE elements,
as described in the previous section.
Each UR with the IEC 61850 order code option has 64 RxGOOSE elements. Each RxGOOSE element can subscribe to GOOSE
messages from a specified publisher. Each RxGOOSE can either use the original format specified in IEC 61850 8 1:2011 or
the routable GOOSE (R-GOOSE; IEC 61850 Edition 2) format specified in IEC TR 61850-90-5:2012. Subscribed message
members can be DataObjects, SubDataObjects, DataAttributes or SubAttributes. In E2-2.0 mode members are restricted to
basic types BOOLEAN, FLOAT32, INT32, Dbpos, TimeStamp or Quality. Each subscribed message can contain up to 64
values. A member can be a structure containing several values; note that it is the number of values rather than the number
of members that are limited to 64.

GOOSE messages from any device of any manufacturer that implements the IEC 61850 Edition 1.0 or 2.0 GOOSE publish
service or the 61850-90-5 R-GOOSE service (IEC 61850 Edition 2) can be subscribed to. The UR accepts both the variable
length encoded GOOSE messages specified IEC 61850 8 1:2004 and the Fixed-Length encoded GOOSE messages as
specified in IEC 61850 8 1:2011 clause A.3.
Each enabled RxGOOSE monitors for interruption of the GOOSE messages it subscribes to based on the value in the
timeAllowedtoLive field of the last message received. If a new message is not received within that time interval, the
RxGOOSE assumes that connectivity is lost. FlexLogic operands (for example RxGOOSE1 On, RxGOOSE1 Off) reflect the
status of each RxGOOSE connectivity. An RxGOOSE connection is also considered lost after the UR finishes restart until a
message is received. While any RxGOOSE connectivity is lost, a common RxGOOSE Fail self-test is activated.
Messages that contain the value true in the ndsCom field are never accepted. Messages that contain the value true in the
simulation field (test field in edition 1.0 messages) are accepted only when the UR Test Mode Function setting is set to
Forcible or Isolated.
RxGOOSE messages can be received through any UR Ethernet port.
Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > RxGOOSE > RxGOOSE Messages >
RxGOOSE1 to access the settings that specify the messages to be accepted by the first RxGOOSE element. The settings
and functionality for the other RxGOOSE are similar. The following settings are available. They allow RxGOOSE1 to
recognize the GOOSE messages it is to accept. Most of these settings are automatically configured by UR Setup software
when an association to an RxGOOSE Boolean Input, RxGOOSE DPS Input, and/or RxGOOSE Analog Input is made as
described in the sections following this. For IEC 61850 Edition 2, settings R-RxGOOSE1 RECEPTION MODE, R-RxGOOSE1
SECURITY, and R-RxGOOSE SRC IP need to be manually completed as the information is not contained in publisher SCL.
Figure 5-27: IEC 61850 RxGOOSE Messages panel (Edition 2)
RxGOOSE1 MODE
Range for Edition 2: GOOSE, R-GOOSE
Range for Edition 1: GOOSE
Default: GOOSE
When set to GOOSE, TxGOOSE1 messages are published in IEC 61850 8 1:2011 GOOSE format. When set to R-GOOSE,
TxGOOSE1 messages are published in Routable GOOSE format according to IEC 61850 90-5. When set to R-GOOSE, the
R-RxGOOSE DST IP needs to be a valid multicast or unicast IP address.

RxGOOSE1 goID
If the entered value has one or more characters, the goID field of incoming GOOSE messages must exactly match this
value for the message to be accepted as a valid RxGOOSE1 message. If the entered value is the empty string, RxGOOSE1
does not check the value received in the goID field. Special characters are not allowed, such as <, >, &, ’, and ".
If the publisher is a UR 7.3x series device, this setting needs match the value of the publisher's TxGOOSE GoID setting.
RxGOOSE1 Dst MAC
Range: any 12 digit hexadecimal number
Default: 01-0C-CD-01-00-00
When the RxGOOSE1 MODE setting is R-GOOSE, the value of this setting is not used, the destination Media Access
Control (MAC) address for RxGOOSE1 messages is calculated based on the RxGOOSE DST IP address. Otherwise, set this
setting to the MAC address of the publisher. Only received GOOSE messages having a MAC address equal to this value
are accepted as valid RxGOOSE1 messages. An entered address of zero disables RxGOOSE1.
If the publisher is a UR series 7.3x device, the setting needs to match the value of the publisher’s TxGOOSE DST MAC
setting.
RxGOOSE1 ETYPE APPID
Default: 0
If the value entered is non-zero, the APPID field of incoming GOOSE messages must exactly match this value for the
message to be accepted as a valid RxGOOSE1 message. If the value entered is zero, RxGOOSE1 does not check the value
received in the APPID field.
5 If the publisher is a UR series 7.3x device, the setting needs to match the value of the publisher’s TxGOOSE ETYPE APPID
setting.
RxGOOSE1 GoCBRef
Range: 0 to 129 alphanumeric, underscore, slash and period characters, beginning with an alpha character
The gocbRef field of incoming GOOSE messages must match this value for the message to be accepted as a valid
RxGOOSE1 message. If the entered value is the empty string, RxGOOSE1 is disabled. If not the empty string, the entry
needs to be an ACSI ObjectReference to the publishing control block in the format:
<LDName>/LLN0.<GoCBName>
where <LDName> is the function-related name if the logical device containing the publishing control block has "ldName"
configured, otherwise the product-related name of that logical device, and <GoCBName> is the name of the publishing
control block.
The B90 translates the ACSI format required for this setting to the MMS format used in GOOSE messages:
<LDName>/LLN0$GO$<GoCBName>
If the publisher is a UR 7.3x or 7.40 series device, <LDName> is the value of the publisher's Master functional ldName
setting if that setting is not empty, otherwise it is the value of the publisher's IED NAME suffixed with "Master". If the
publisher is a UR 7.3x series device, <GoCBName> is "GoCB" suffixed with the two digit TxGOOSE instance number, for
example "GoCB01". If the publisher is a UR 7.40 series device, <GoCBName> is as specified earlier in the TxGOOSE
section of this chapter.
RxGOOSE1 datSet
Range: 0 to 32 alphanumeric and underscore characters, beginning with an alpha character
If the entered value has one or more characters, the datSet field of incoming GOOSE messages must exactly match this
value prefixed by <LDName>/LLN0$ for the message to be accepted as a valid RxGOOSE1 message. <LDName> is as
specified in the RxGOOSE GoCBRef setting above. If the entered value is the empty string, RxGOOSE1 does not check the
value received in the datSet field.
If the publisher is a UR 7.3x series device, set this setting to the value of the publisher's DataSetxx name setting, where xx
is the instance number of the data set selected by the publisher's TxGOOSE datSet setting. If the publisher is a UR 7.40
series device, datSet is as specified in the DataSets section of this chapter.

RxGOOSE1 ConfRev
Default: 1
If the value entered is non-zero, the confRev field of incoming GOOSE messages must exactly match this value for the
message to be accepted as a valid RxGOOSE1 message. If the entered value is zero, RxGOOSE1 does not check the value
received in the confRev field.
If the publisher is a UR 7.3x series device, set this setting to match the value of the publisher's TxGOOSE ConfRev setting.
R-RxGOOSE1 RECEPTION MODE
Range: SSM, ASM, Unicast
Default: SSM
When the RxGOOSE1 MODE setting is other than R-GOOSE the value of this setting is not used. Otherwise it selects the
R-GOOSE reception mode.
R-RxGOOSE RECEPTION MODE specifies the R-RxGOOSE DST IP range. When set to SSM, R-RxGOOSE DST IP must be in
the range of 232.0.0.1 to 232.255.255.255. When set to ASM, R-RxGOOSE DST IP must be in the range of 224.0.0.1 to
239.255.255.255, excluding the SSM range. Note that the SSM range is inside the ASM range and therefore the ASM use
excludes the SSM range. The default destination IP address 224.0.0.0 is reserved, and hence not a valid multicast IP
address.
The reception modes are related to Layer-3 R-GOOSE reception from routers/WAN. The subscription to multicasting of R-
GOOSE is supported using IGMP Protocol Independent Multicast (PIM). It is made available in either Source Specific
Multicast (SSM) mode or Any Source Multicast (ASM) mode. Unicast (over UDP) mode can also be used. In case of
multicasting (IGMPv3 based SSM or ASM), the R-GOOSE subscriber device requests the Last Hop Router (LHR) to
subscribe to a specific multicasting group.
If the publisher is using a unicast destination IP address for this R-GOOSE, then set R-RxGOOSE1 RECEPTION MODE to 5
Unicast. Otherwise set R-RxGOOSE1 RECEPTION MODE to the SSM or ASM mode used by the local routers/firewalls.
R-RxGOOSE1 SRC IP
Default: 127.0.0.1
When the RxGOOSE1 MODE setting is other than R-GOOSE, the value of this setting is not used. When the RxGOOSE1
MODE setting is R-GOOSE and the R-RxGOOSE RECEPTION MODE setting is ASM, the value of this setting is not used.
Otherwise the Source IP Address field of incoming R-GOOSE messages must exactly match this value for the message to
be accepted as a valid RxGOOSE1 message. Set this setting to the value of the source IP address used by the publisher.
For UR publishers, this value is in setting PRT# IP ADDRESS.
The UR does not validate the address entered. The default IP address 127.0.0.1 is a reserved, not a valid IP address. Enter
a valid IP source address.
R-RxGOOSE1 DST IP
Default: 224.0.0.0
When the RxGOOSE1 MODE setting is other than R-GOOSE, the value of this setting is not used. Otherwise the
Destination IP Address field of incoming R GOOSE messages must exactly match this value for the message to be
accepted as a valid RxGOOSE1 message. Set this setting to the same value as the R-GOOSE publisher's Destination IP
Address. For UR publishers, this value is in setting R-TxGOOSE# DST IP.
The destination IP address needs to be a valid multicast or unicast IP address. The UR does not validate the address
entered. The default IP address 224.0.0.0 is reserved, and hence not a valid multicast IP address.
R-RxGOOSE1 SECURITY
Range: None, Signature, SignatureAndEncryption
Default: None

This setting specifies the level of security (authentication/encryption) used for RxGOOSE1. None indicates no security
mechanisms are in use. Signature indicates only signature (no encryption) is in use. SignatureAndEncryption indicates
that both signature and encryption are in use. Normally this setting is set to match the GOOSE publisher's security
method.
RxGOOSE1 Member 1
Range: End of List, BOOLEAN, FLOAT32, INT32, Dbpos (DPS), Quality, TimeStamp, Struct
Default: End of List
This setting specifies the type that the first member of incoming GOOSE messages must be for the message to be
accepted as a valid RxGOOSE1 message. There are similar settings for each of the up to 64 members that the UR is able
to subscribe to in a given GOOSE message. The member before the first member setting set to "End of List" must be the
last member of the message for the message to be accepted as a valid RxGOOSE1 message.
If the publisher is a UR 7.3x or 7.40 series device, set these settings to match the basic type of the members of the
publisher's data set selected by the publisher's TxGOOSE datSet setting.
If the publisher dataset includes members with structured data, that is, data attributes, sub-data objects, and/or data
attributes with sub-data attributes, configuration must use one of the new 7.40 UR Setup RxGOOSE Inputs pages. In this
case the Member setting displays as the product-related name used by the publishing IED of the data object or data
attribute, in standard SCSM format (e.g. Publisher1LD1/LLN0$ST$Off$stVal).
Note that a dataset can hold at most 64 basic data attribute values, and that a single structured data object or attribute
can contain multiple basic data attribute values. UR Setup software does not allow more that 64 basic data attribute
values to be entered, in which case the last several members settings cannot be changed from End of List.
Note that the publisher's name alone does not contain all the information required for subscription, additional publisher
information model information is stored elsewhere. For this reason, manual entry of the name is not supported.
5 RxGOOSE inputs
The values received by RxGOOSE elements need to be converted to FlexLogic or FlexAnalog operands so that they can be
used by other UR elements. This conversion is done by RxGOOSE Boolean, RxGOOSE DPS, and RxGOOSE Analog elements.
Each RxGOOSE Boolean can convert the value of a specified Boolean value received by a specified RxGOOSE to a FlexLogic
operand. Each RxGOOSE DPS can convert the value of a specified Dbpos (Double bit position) value to four FlexLogic
operands, one for each of the four possible Dbpos states. Each RxGOOSE Analog can convert the value of a specified
FLOAT32 member to a FlexAnalog operand. Each of these operands reverts to its default state when the RxGOOSE
connectivity is lost. Other types of values can be present in subscribed GOOSE messages, but cannot be converted to
operands.
When an RxGOOSE Input is mapped to a value in the GOOSE message, the associated q value is validated, if the q value is
included in that GOOSE message as part of the data object.
The RxGOOSE Input value is reverted to its default value, if the associated:
• q.validity is invalid
• or q.test bit is set and the relay test mode is disabled
When the test mode function is Forcible or Isolated, the q.test bit is not validated. That means, when the relay is in Test or
Test/blocked mode, the q.test = False is treated same as q.test = True.
RxGOOSE Boolean, RxGOOSE DPS, and RxGOOSE Analog elements are mapped to various data objects in
<iedName>Master/GGIO3. This is to allow reading of their values via MMS and to allow references to them in SCL files.
GGIO3 has no settings, nor is it visible in the UR Setup software. See the UR Family Communications Guide for more
information on GGIO3.
RxGOOSE Boolean inputs

Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > RxGOOSE > RxGOOSE Boolean Inputs.
The number of RxGOOSE Boolean (remote inputs) is 256.

There are Add IED and Remove IED buttons. The Add IED button allows SCL files to be used, including ICD, CID, and SCD
(supported in version 7.40 and later). With SCL file import, for Edition 1 the IP address in the ConnectedAP element must
match one IP address of the device, while for Edition 2 one of the three IP addresses in the ConnectedAP element must
match. When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. The
figure shows a selection being made by importing a CID file using the Add IED function.
Figure 5-28: RxGOOSE Boolean panel (Edition 2)
Most of the settings are configured by drag-and-drop. However the ID, DEFAULT STATE, and EVENTS settings must be
individually entered when the factory default values are not acceptable.
RxGOOSE Boolean1 ID
Range: 0 to 20 characters
Default: RxG Bool1
This setting allows the user to assign descriptive text to the name of the RxGOOSE Boolean1 FlexLogic operand. The full
operand name is the value of this setting appended with " On". The basic and enhanced front panels display the first 17
characters of this setting plus " On" to fit the 20 character display.
RxGOOSE Boolean1 RxGOOSE
Range: None, RxGOOSE1, RxGOOSE2, and so on
Default: None
This setting selects the RxGOOSE containing the value that drives the RxGOOSE Boolean1 FlexLogic operand. If set to
None, the RxGOOSE Boolean1 FlexLogic operand assumes its default state.
RxGOOSE Boolean1 Member
Default: 1
This setting selects the GOOSE message member that drives the RxGOOSE Boolean1 FlexLogic operand. A setting of 1
selects the first member, 2 selects the second member, and so on. Entering a number greater than the number of
members in the message and entering the number of a member which does not contain a BOOLEAN results in the
RxGOOSE Boolean1 FlexLogic operand assuming its default state. The Subscribed to column identifies the particular
Boolean subscribed to even if the member is a structure containing more than one Boolean.

RxGOOSE Boolean1 DEFAULT STATE

Range: On, Off, Latest/On, Latest/Off
Default: Off
This setting selects the logic state for the RxGOOSE Boolean1 FlexLogic operand if the UR has just completed startup and
the selected RxGOOSE has not yet received a message, or the selected RxGOOSE has lost its connectivity with the
publisher. The following choices are available:
– "On" value defaults the input to logic 1
– "Off" value defaults the input to logic 0
– "Latest/On" freezes the input in case of lost connectivity. If the latest state is unknown, such as after UR power-up
but before the first communication, the input defaults to logic 1. When communication resumes, the input
becomes fully operational.
– "Latest/Off" freezes the input in case of lost connectivity. If the latest state is unknown, such as after UR power-up
but before the first communication, the input defaults to logic 0. When communication resumes, the input
becomes fully operational.
RxGOOSE Boolean1 EVENTS
Range: Disabled, Enabled
Default: Disabled
This setting selects whether Off to On transitions of the RxGOOSE Boolean1 FlexLogic operand are recorded by the event
recorder. If set to Enabled, Off to On transitions are recorded. On to Off transitions are never recorded, even if events are
enabled.
RxGOOSE DPS inputs

5 Navigate to Settings > Product Setup > Communications > IEC 618560 > GOOSE > RxGOOSE > RxGOOSE DPS Inputs.
match. When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add.
Figure 5-29: RxGOOSE DPS Inputs panel (Edition 2)

RxGOOSE DPS1 ID
Default: RxG DPS1
This setting allows the user to assign descriptive text to the names of the four RxGOOSE DPS1 FlexLogic operands. The
full operand name is the value of this setting appended with "Interm," "On," "Off," or "Bad." The basic and enhanced front
panels display the first 13 characters of this setting plus the state suffix to fit the 20 character display.
RxGOOSE DPS1 RxGOOSE
Default: None
This setting selects the GOOSE message containing the value that drives the RxGOOSE DPS1 FlexLogic operand. If set to
None, the RxGOOSE DPS1 FlexLogic operand assumes its default state.
RxGOOSE DPS1 Member
Default: 1
This setting selects the GOOSE message member that drives the RxGOOSE DPS1 FlexLogic operand. A setting of 1 selects
the first member, 2 selects the second member, and so on. Entering a number greater than the number of members in
the message and entering the number of a member that is not a Dbpos results in the RxGOOSE DPS1 FlexLogic operand
assuming its default state. In the case that the member is a structure containing more than one Dbpos, the Subscribed
to column identifies the particular Dbpos subscribed to.
RxGOOSE DSP1 DEFAULT STATE
Range: Intermediate-state, Off, On, Bad-state, Latest
Default: Latest
This setting selects the logic state for the data attribute @Master/GGIO3.IndPos01.stVal and the DPS FlexLogic operands
when the UR has just completed start-up and the selected RxGOOSE has not yet received a message, and when the 5
RxGOOSE has lost its connection with the publisher. When this setting is selected to Latest, the value of @Master/
GGIO3.IndPosψψ.stVal is Intermediate-state when the UR has just completed start-up and the selected RxGOOSE has
not yet received a message, and the latest received value when the RxGOOSE loses its connectivity with the publisher.
RxGOOSE DPS1 EVENTS
Default: Disabled
This setting selects whether Off to On transitions of the RxGOOSE DPS1 FlexLogic operands are recorded by the event
recorder. If set to Enabled, Off to On transitions are recorded. On to Off transitions are never recorded, even if events are
enabled.
RxGOOSE analog inputs

Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > RxGOOSE > RxGOOSE Analog Inputs.
match. When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add.

Figure 5-30: RxGOOSE Analog Inputs panel (Edition 2)
There are 32 RxGOOSE analog inputs.

RxGOOSE Analog1 ID
Default: RxG Analog1
5 This setting allows the user to assign descriptive text to RxGOOSE Analog1. Unlike RxGOOSE Booleans and RxGOOSE
DPS, the RxGOOSE Analog operands have fixed names, for example RxGOOSE Analog1.
RxGOOSE Analog1 RxGOOSE
Default: None
This setting selects the GOOSE message that drives the RxGOOSE Analog1 FlexAnalog operand. If set to None, the
RxGOOSE Analog1 FlexAnalog operand assumes its default state.
RxGOOSE Analog1 Member
Default: 1
This setting selects the GOOSE message member that drives the RxGOOSE Analog1 FlexAnalog operand. A setting of 1
selects the first member, 2 selects the second member, and so on. Entering a number greater than the number of
members in the message and entering the number of a member that does not contain a FLOAT32 results in the
RxGOOSE Analog1 FlexAnalog operand assuming its default state. The Subscribed to column identifies the particular
FLOAT32 subscribed to even if the member is a structure containing more than one FLOAT32.
RxGOOSE Analog1 DEFAULT
Range: -1000000.000 to 1000000.000 in steps of 0.001
Default: 1000.000
This setting specifies the value of the GOOSE analog input when the selected RxGOOSE has lost its connectivity with the
publisher and the RxGOOSE Analog1 DEFAULT MODE is set to "Default Value." Otherwise this setting has no effect. This
setting is stored as an IEEE 754 / IEC 60559 floating point number. Because of the large range of this setting, not all
possible values can be stored. Some values can be rounded to the closest possible floating point number.

RxGOOSE Analog1 DEFAULT MODE

Range: Default Value, Last Known
Default: Default Value
When the selected RxGOOSE has lost its connectivity with the publisher and this setting is "Last Known," the value of the
RxGOOSE Analog1 FlexLogic operand remains at the last received value. When the selected RxGOOSE has lost its
connectivity with the publisher and this setting value is "Default Value," then the RxGOOSE Analog1 FlexLogic operand is
defined by the RxGOOSE Analog1 DEFAULT setting. After restart, until a message is received, the operand value is the
default value.
RxGOOSE Analog1 UNITS
Range: up to 4 characters
This setting specifies a four-character string that is used in the actual values display of RxGOOSE Analog1.
RxGOOSE Analogs are floating-point values, with no units. The RxGOOSE UNIT and PU base settings allow the user to
configure RxGOOSE Analog, so that it can be used in a FlexElement.
RxGOOSE Analogs that represent current, voltage, power, frequency, angles, or power factor can be used in a
FlexElement. The following text must be used in the UNITS setting, to represent these types of analogs: A, V, W, var, VA,
Hz, deg, and no text (blank setting) for power factor.
RxGOOSE Analogs can be compared to other RxGOOSE Analogs with any character string or no string.
RxGOOSE Analog1 PU Base in kilo
Range: 0.000 to 1000000000.000 in steps of 0.001
Default: 1.000
This setting specifies the per-unit base value for other B90 features to use with the RxGOOSE Analog1 operand. A
FlexElement for instance subtracts two quantities after converting their values to integers rescaled to a common base,
the common base being the largest of the base values of the two quantities. If one of quantities is RxGOOSE Analog1 and 5
its per-unit base value is not appropriate, the rescaling operation can result in unnecessary loss of precision or overflow
in the integer result. The FlexElement Base Units table in the Settings > FlexLogic > FlexElements section later, which
tabulates the per-unit base value used by its pickup setting and implies the per-unit base used by other FlexAnalogs, can
be of use in selecting a value for the RxGOOSE Analog1 PU setting.
Some UR elements have requirements for the type of input operands, for instance current type or voltage type. These
elements assume that RxGOOSE Analog operands are of whatever type is necessary to meet these requirements.
The per-unit base setting represents thousands, not single units. For example, a PU base of 1.000 is actually 1000 and a
PU base of 0.001 is 1.
When using RxGOOSE Analogs and PU base in FlexElements, the largest value that can be displayed in the FlexElement
actual values is 2,140,000.000.
Reports
Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports.
Report settings
Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports > Report Settings.
ReportSettings rptID
Range: Dyn, Conf
Default: Dyn
When set to Dyn, the RptID attribute in any buffered and unbuffered report control block can be modified by an MMS
client while the control block's RptEna attribute is false. The RptID is the name of the report.
ReportSettings optFields
Range: Dyn, Conf
Default: Dyn
When set to Dyn, the OptFlds attribute in any buffered and unbuffered report control block can be modified by an MMS
client while the control block's RptEna attribute is false.

ReportSettings bufTime
Range: Dyn, Conf
Default: Dyn
When set to Dyn, the BufTm attribute in any buffered and unbuffered report control block can be modified by an MMS
ReportSettings trgOps
Range: Dyn, Conf
Default: Dyn
When set to Dyn, the TrgOps attribute in any buffered and unbuffered report control block can be modified by an MMS
ReportSettings intgPd
Range: Dyn, Conf
Default: Dyn
When set to Dyn, the IntgPd attribute in any buffered and unbuffered report control block can be modified by an MMS
Buffered and unbuffered reports

Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports > Buffered Reports or Unbuffered
Reports.
Figure 5-31: IEC 61850 buffered report panel

An IEC 61850 Report server is an efficient method to deliver generic substation event information from a single server to a
single client, such as a supervisory control IED. A Configurable Report is a UR element implementing an IEC 61850 Report
server, either of the buffered or unbuffered kind. The following table lists the number of Configurable Report elements.
Each Configurable Report element can report the values of up to 64 FlexLogic or FlexAnalog operands. Buffered report
elements queue value changes that occur while the client is offline and delivered when the client re-connects. Up to 512
events can be queued. Unbuffered control blocks purge all value change events when the connection to the client is lost;
any events that occur while the client is not connected are lost.
Table 5-11: Number of report elements
Number
Buffered reports 30
Unbuffered reports 18
When using IEC 61850 Edition 2, configurable Reports interoperate with any client device of any manufacturer that
conforms to the IEC 61850 edition 1.0 or 2.0 report client requirements.
When using IEC 61850 Edition 1, configurable Reports interoperate with any client device of any manufacturer that
conforms to the IEC 61850 edition 1.0 report client requirements.
The entities whose values are reported by a Configurable Report are known as members. The members are itemized in an
ordered list known as a data set. Each Configurable Report can use any one of the data sets provided that no more than
four data sets are used for reports. This restriction is to limit the amount of processing power that can be allocated to
reporting.
Each enabled Configurable Report transmits an update to its client whenever a value change is detected in one or more of
its members. Also, the control block can be configured to send integrity reports containing the present value of all
members either on demand from the client or periodically. A TCP handshaking mechanism causes messages that are not
read and acknowledged by the client to be retransmitted. 5
For a Configurable Report to operate, its members must be selected (that is, its data set configured) and a client must open
a connection to, configure, and enable its report control block. Control blocks and data sets can be pre-configured by
sending the B90 a CID file. See the UR Family Communications Guide for details. EnerVista UR Setup also can be used to
select the data set members and to pre-configure the control blocks.
Each buffered report has the following settings.
Buffered Report1 RptID
The name of the report. The entered value sets the RptID value in Buffered Report1 messages, and it can be used by the
client to discriminate Buffered Report1 messages from other messages. If the number of characters entered is zero, the
value used for RptID in messages is an ObjectReference to the report's control block, that is, "<LDName>/
LLN0$BR$"BRCB01".
Buffered Report1 Name
Default: BRCB01
The entered value sets the report control block name value for Buffered Report1.
Buffered Report1 DatSet
Range: None, TT6DataSet1, TT6 DataSet2, …, TT3DataSet01, TT3DataSet02, …
Default: None
This setting selects the data set whose members' status is reported in Buffered Report1 messages using the UR Setup
software designator for the data set. The IEC 61850 name of the data sets are configured in the Datasets panel, as
described later.
An ObjectReference to the data set, which consists of the concatenation of the string "<LDName>/LLN0$" and the data
set name, is used in the datSet field of report messages, and it can be used by the client to discriminate Buffered Report1
messages from other messages.

The performance of the report is determined by the performance of the selected dataset. When the selection is
To configure a DataSet, select it at the top of the window from the drop-down list, for example DataSet02 shown in the
previous figure. In the lower part of the window, drag and drop configuration items to the right side. For example select
the ST Ind001 stVal item and drag it to DataSet Member 1. Dataset members configured here affect other Report or
TxGOOSE control blocks that use the same DataSet.
Buffered Report1 ConfRev
Default: 1
The entered value sets the confRev value in Buffered Report1 messages, and it can be used by clients to discriminate
report messages of the expected configuration revision from messages of a different revision. The standard requires
that confRev be incremented each time the members or the order of the members is changed, and each time the data
set name is changed. The standard states that the value of 0 is reserved.
Buffered Report1 OptFlds
Range: The check box for each individual bit can be enabled or not (see figure)
Default: All bits enabled/ true
The OptFlds setting is bitstring that controls which of the optional fields are included in report messages. The figure
shows the available option bits. To reduce message size, uncheck any fields that are not needed.
Figure 5-32: Options for buffered report messages (Edition 2)
Buffered Report1 BufTm

Default: 0 ms
The entered value sets the time interval in milliseconds for the buffering of events for inclusion in a single report.
Buffered Report1 TrgOps
Range: The check box for an individual bit can be enabled or not
Default: All bits enabled / true
The TrgOps setting is bitstring that controls which trigger conditions are monitored in this report. The options are as
follows. Uncheck any trigger conditions that are not needed.
– data-change
– quality-change
– integrity
– general interrogation (IEC 61850 Edition 2)
Buffered Report1 IntgPd
Default: 0 ms
The entered value sets the period in milliseconds for generating Buffered Report1 integrity reports. An integrity report
includes the values of all members of the referenced data set, whether a change has occurred or not.
Each unbuffered report has the following settings.

Unbuffered Report1 RptID

The name of the report. The entered value sets the RptID value in Unbuffered Report1 messages, and it can be used by
the client to discriminate Unbuffered Report1 messages from other messages. If the number of characters entered is
zero, the value used for RptID in messages is an ObjectReference to the report's control block, that is, "<LDName>/
LLN0$RP$"URCB01".
Unbuffered Report1 Name
Range: 0 up to 32 VisibleString characters
Default: URCB01
The entered value sets the report control block name value for Unbuffered Report1.
Unbuffered Report1 DatSet
Range: None, TT6DataSet1, TT6 DataSet2, …, TT3DataSet01, TT3DataSet02, …
Default: None
This setting selects the data set whose members' status is reported in Unbuffered Report1 messages using the UR Setup
software designator for the data set. The IEC 61850 name of the data sets are configured in the Datasets panel, as
described later.
An ObjectReference to the data set, which consists of the concatenation of the string "<LDName>/LLN0$" and the data
set name, is used in the datSet field of report messages, and it can be used by the client to discriminate Unbuffered
Report1 messages from other messages.
The performance of the report is determined by the performance of the selected dataset. When the selection is
Unbuffered Report1 ConfRev
5
Default: 1
The entered value sets the confRev value in Unbuffered Report1 messages, and it can be used by clients to discriminate
report messages of the expected configuration revision from messages of a different revision. The standard requires
that confRev be incremented each time the members or the order of the members is changed, and each time the data
set name is changed. The standard states that the value of 0 is reserved.
Unbuffered Report1 OptFlds
The OptFlds setting is bitstring that controls which of the optional fields are included in report messages. The options are
as follows. To reduce message size, uncheck any fields that are not needed.
– sequence-number
– report-time-stamp
– reason-for-inclusion
– data-set-name
– data-reference
– conf-revision
For IEC 61850 Edition 2, the OptFlds bits buffer-overflow and entryID also listed are not applicable to unbuffered reports
even though the bits exist in the protocol. They are unchecked by default.
For IEC 61850 Edition 1, the entryID also listed is not applicable to unbuffered reports even though the bits exist in the
protocol. It is unchecked by default.
Unbuffered Report1 BufTm
Default: 0 ms
The entered value sets the time interval in milliseconds for the buffering of events for inclusion into a single report.

Unbuffered Report1 TrgOps

The TrgOps setting is bitstring that controls which trigger conditions are monitored in this report. The options are as
follows. Uncheck any trigger conditions that are not needed.
– data-change
– quality-change
– integrity
– general interrogation (IEC 61850 Edition 2)
Unbuffered Report1 IntgPd
Default: 0 ms
The entered value sets the period in milliseconds for generating Unbuffered Report1 integrity reports. An integrity report
includes the values of all members of the referenced data set, whether a change has occurred or not.
DataSets
Navigate to Settings > Product Setup > Communications > IEC 61850 > DataSets.
As mentioned in the preceding GOOSE and Reports sections, the members whose values are communicated by these
services are itemized in an ordered list known as a data set. Each UR with the IEC 61850 option has 18 data sets (six fast
and 12 slow). Each data set can contain as many as 64 members. Any data set can be used simultaneously by any number
of TxGOOSE elements and/or by any number of Configurable Report elements. UR Setup software can configure any
FlexLogic operands and any FlexAnalog operands as members.
5 Figure 5-33: IEC 61850 DataSets (Edition 2)

UR Setup software requires data set members to be IEC 61850 data objects or data attributes with Functional Constraint
ST or MX. Certain FlexLogic and FlexAnalog operands have factory-assigned data attributes as tabulated in the UR Family
Communications Guide. All FlexLogic and FlexAnalog operands can be user-assigned to GGIO1 or GGIO4 data attributes,
so that operands without factory-assigned data attributes can still have their values published. See the GGIO1 and GGIO4
sections later for details.
Datasets used by TxGOOSE1, TxGOOSE2, and/or by reports also provide a chatter suppression service for their Boolean
members. Oscillation in a value, also known as chatter, can be caused by errors in logic programming, inadequate
hysteresis (deadband) on a threshold, or a failed station component. Chatter can flood a communications network with
GOOSE messages, degrading response time for all users. If chatter is detected in a Boolean member, TxGOOSE suspends
GOOSE event message triggering and report message triggering from that member for as long as the condition exists, and
for a minimum period of one second. While sending is suspended, a self-test message identifying the specific data item
detected as oscillating is activated.
For a summary of the panels in which the data sets are used, the path is Settings > Product Setup > Communications >
IEC 61850 > DataSets > Summary.
For the settings, navigate to Settings > Product Setup > Communications > IEC 61850 > DataSets > TT6DataSet1 for the
first data set.
Copy and paste functions are available when right-clicking a DataSet. They allow the target dataset to be configured
based on its order code. If some dataset items are not supported, they are not pasted, and a warning message shows a list
of dataset items that were not supported and not pasted. The DataSet name is not copied or pasted. In short, use this
feature to copy a DataSet Member setting and paste it into another Member setting, a text file, or Word, as examples.
Figure 5-34: Member right-click
DataSet01 name
Default: DataSet01
The value entered sets the name of the data set, which is required to be unique within the UR for proper operation. The
value entered sets the name of the data set, which is required to be unique within the UR for proper operation. Fast
datasets start with TT6, and slow datasets start with TT3. Up to six fast datasets are allowed. Up to four fast GOOSE
datasets are allowed.

An ObjectReference to the data set consists of a string that is the concatenation of "<LDName>/LLN0$" and the
DataSet01 name setting value. An ObjectReference to the data set is published in the datSet field of TxGOOSE messages,
and it can be used by subscribers to discriminate the messages of that TxGOOSE from other GOOSE messages. An
ObjectReference to the data set is optionally published in the DatSet field of Report messages. Valid characters are
upper and lowercase letters, digits, and the underscore (_) character. The first character must be a letter.
DataSet01 shared by
Default:
Names of all control blocks that use this DataSet. Read-only field.
DataSet01 Member1
Range: End of List or any instantiated 61850 data object or data attribute with Functional Constraint ST or MX
Default: End of List
This setting specifies the first member in TxGOOSE1 messages. There is a similar setting for each of the up to 64
members that the UR allows in a Dataset. Only values of members before the first set to End of List are published.
Select the member from the drop-down list. Or right-click an entry to copy, paste, delete, or insert.
Product setup
Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup.
Security
Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup > Security.
5 Figure 5-35: IEC 61850 Security
SecGSAL1.SecDataClr.ctlModel
Range: direct-with-normal-security, sbo-with-normal-security
Default: direct-with-normal-security
This setting selects the control model that clients must use to clear security data via commands to
SecGSAL1.SecDataClr. "sbo" here is select-before-operate.

SecGSAL1.OpCntRs ctlModel
This setting selects the control model that clients must use to clear security data via commands to SecGSAL1.OpCntRs.
"sbo" here is select-before-operate.
Demand
Deadband parameters of measured values related to the Demand metering are configured here.
Energy
Deadband parameters of measured values related to the Energy metering are configured here.
Real Time Clock

Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup > Real Time Clock.
Figure 5-36: IEC 61850 Real Time Clock
TmClkLTMS1.TmnsDelta.db
Range: 0.000 to 100.000 %
Default: 0.000 %
This setting is a deadband setting and is used by the relay to determine when to update the "mag" and "cVal" values
from the associated "instMag" and "instCVal" values. The value shall represent the percentage of difference between
maximum and minimum in units of 0.001%. The minimum and maximum values for TmnsDelta data object are
-500000000 ns and 500000000 ns respectively and for example, a setting value of 0.002% results in the dead banded
value of (500000000 - (-500000000)) * 0.002 / 100 = 20000 ns. The default setting value of 0.000% does not update the
"mag" and "cVal" values.
Deadband settings
A deadband is a range in which no action occurs, usually expressed as a percentage.
The IEC 61850 panels contain hundreds of deadband settings, such as in the following panels: Product Setup > Real Time
Clock, FlexLogic, Control Elements, and GGIO4. Each panel is not outlined here. The FlexLogic category applies to IEC 61850
Edition 2.

Deadband setting names all end either with "DB" or .db. As they all work the same way, but each on a different analog
value, a single description applicable to all deadband settings is given here. The analog value that each deadband setting
applies is usually obvious from the name of the setting. However, a tabulation of the analog values and their associated
deadband setting can be found in the UR Family Communications Guide.
Figure 5-37: Deadband settings with .db suffix (Edition 2)
GOOSE, buffered report, and unbuffered report messages are for the most part transmitted only when there is a value
5 change in one or more of their members. Most analog values continuously dither by an amount that is not significant.
Were a report to be sent each time an insignificant analog value change occurred, then the communications network
floods with GOOSE and report messages, degrading response time for all users.
To control this, a deadband setting is provided for each analog value. Also, in addition to the present actual value of each
analog ("instMag" in the following figure), there is a deadbanded value ("mag" in the figure), which is updated with the
present value only when the difference between the two exceeds the deadband setting (db in the figure). Changes to this
deadbanded value trigger transmissions when included in GOOSE and report data sets.
Figure 5-38: Deadband settings
Deadband settings are entered in UR Setup software in units of percent of the difference between the "max." and "min." of
the associated analog value. A zero deadband setting suppresses transmission triggering. The range of deadband settings
is 0.000 to 100.000% in steps of 0.001. The default value is 0.000%.
GGIO4 elements have individual settings for "min." and "max." The min. and max. for FlxEIGAPC#.OpSig.db (FLEXELEMENT #
OpSig) are -50 pu and +50 pu respectively. The min. value for all other quantities is 0. The max. values are as follows:
• Phase current — 46 x phase CT primary setting
• Neutral current — 46 x ground CT primary setting
• Ground current (sensitive ground CT) — 4.6 x sensitive ground CT primary setting
• Phase, phase-to-phase, and sequence voltage — 275 x phase VT ratio setting

• Auxiliary voltage — 275 x auxiliary VT ration setting

• Power (real, reactive, apparent, 3-phase, and 1-phase) — 4 × phase CT primary setting × 1.5 × VT Secondary setting ×
VT ratio setting
• Energy (real or imaginary) — 4 × phase CT primary setting × 1.5 × VT Secondary setting × VT ratio setting x 1 hour
• Frequency — 90 Hz
• Frequency rate of change — 90 Hz/s
• Power factor — 2
• Angle — 360 degrees
Select the deadband settings from knowledge of the characteristics of the power system quantity measured and
knowledge of the demands of the applications receiving the measurement via GOOSE or report such that changes of
significance to the application are promptly reported, yet the network is not overly burdened with event messages.
After making changes to settings that affect the per unit bases, such as CT PRIMARY, CT SECONDARY, VT
SECONDARY, VT RATIO, and VT CONNECTION settings, cycle power to the relay to force recalculation of the IEC
61850 deadband interval in primary units. Until the relay restarts, for some quantities, the deadband interval in
primary units calculated for the previous settings remains in effect.
Signal sources
Deadband parameters of measured values related to the signal sources are configured here.
Setting Groups
The UR implements a setting groups element as detailed in the Control Elements > Setting Groups section of this chapter.
The active setting group and the setting group open for edits can be selected via MMS commands SelectActiveSG and
SelectEditSG. The setting related to these IEC 61850 commands are described here.
5
Navigate to Settings > Product Setup > Communications > IEC 61850 > Control Elements > Setting Groups to access
the setting that configures the IEC 61850 setting group commands.
Figure 5-39: Setting Groups panel (Edition 2)
Initial Setting Group

Default: 1
The entered value sets the initial value of the non-volatile register normally controlled by the service SelectActiveSG. This
initialization occurs only on the UR reboot immediately following the receipt of a valid CID file.

This setting is not mapped into the IEC 61850 information model, but sets the value of SettingControl element attribute
actSG in SCL files.
Commands
The UR implements a number of clear records commands as detailed in the Commands and Targets chapter of this
manual. Several of these commands also can be issued via IEC 61850. The settings related to these IEC 61850 commands
are described here.
Navigate to Settings > Product Setup > Communications > IEC 61850 > Settings for Commands to access the settings
that configure the IEC 61850 protocol interface for record clear commands.
Figure 5-40: Commands panel (Edition 2)
FltRptRFLO1.RsStat.ctlModel
This setting selects the control model clients must use to successfully control the command CLEAR FAULT REPORTS. "sbo"
here is select-before-operate. Enhanced security means that the B90 reports to the client the breaker 1 position at the
end of the command sequence.
LLN0.EvtRcdClr.ctlModel
This setting selects the control model clients must use to successfully control the command CLEAR EVENT RECORDS.
LPHD1.RsStat.ctlModel
This setting selects the control model clients must use to successfully control the command CLEAR ALL RELAY RECORDS.
OscRDRE1.RcdTrg.ctlModel
This setting selects the control model clients must use to successfully control the command FORCE TRIGGER.
OscRDRE1.MemClr.ctlModel
This setting selects the control model clients must use to successfully control the command CLEAR OSCILLOGRAPHY.

DatLogRDRE1.MemClr.ctlModel
This setting selects the control model clients must use to successfully control the command CLEAR DATA LOGGER.
CBArc0SCBR1.MemClr.ctlModel
DmdMtrMMTR1.RsStat.ctlModel
EnrMtrMMTR1.RsStat.ctlModel
GGIO1
GGIO1 is a UR feature that allows up to 128 UR FlexLogic operands to be user-mapped to IEC 61850 information model
data attributes.
For the value of a FlexLogic operand to be read via MMS, included in TxGOOSE messages, or included in buffered/
unbuffered reports, the value must be assigned to a data attribute. GGIO1 allows those FlexLogic operands that have not
yet been factory-assigned to a data attribute to be user-assigned to a generic data attribute, and thus have their values
included in IEC 61850 communications. 5
Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO1 to access the settings for GGIO1.
Figure 5-41: IEC 61850 GGIO1 panel (Edition 2)
GGIO1 INDICATION 1
Range: any FlexLogic operand
Default: OFF
This setting selects the FlexLogic operand whose value is mapped into the IEC 61850 data attribute
<LDName>/GGIO1.Ind001.stVal. See the FlexLogic section in this chapter for a list of FlexLogic operands.

GGIO1 INDICATION 2
Range: any FlexLogic operand
Default: OFF
Selects the FlexLogic operand mapped to <LDName>/GGIO1.Ind002.stVal, and so on.
GGIO2
Virtual Inputs are controllable FlexLogic operands that can be controlled via IEC 61850 commands to GGIO2, by DNP, by
Modbus, and by the UR front panel. The settings related to these IEC 61850 commands are described here.
Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO2 to access the settings that
configure the IEC 61850 protocol interface for Virtual Input commands.
Figure 5-42: GGIO2 panel (Edition 2)
GGIO2 CF SPCSO 1 CTLMODEL

This setting selects the control model clients must use to successfully control Virtual Input 1. "sbo" here is select-before-
operate.
GGIO2 CF SPCSO 2 CTLMODEL
Selects the control model for Virtual Input 2, and so on.
GGIO4
GGIO4 is a UR feature that allows up to 32 UR FlexAnalog operands to be user-mapped to an IEC 61850 information model
data attribute.
For the value of a FlexAnalog operand to be read via MMS, included in TxGOOSE messages, or included in buffered/
unbuffered reports, the value must be assigned to a data attribute. GGIO4 allows those FlexAnalog operands that have not
yet been factory-assigned to a data attribute to be user-assigned to a generic data attribute, and thus have their values
included in IEC 61850 communications.
Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO4 > GGIO4.AnIn1 to access the
settings for the first GGIO4 value. The settings and functionality for the others are similar.

Figure 5-43: GGIO4 panel (Edition 2)
ANALOG IN 1 VALUE
Range: any FlexAnalog operand
Default: OFF
This setting selects the FlexAnalog operand whose value is mapped into the IEC 61850 data attribute
<LDName>/GGIO4.AnIn01.instMag.f. The value of the FlexAnalog operand is converted automatically to the format and
scaling required by the standard, that is to say primary amperes, primary volts, and so on. See Appendix A for a list of
FlexAnalog operands. 5
ANALOG IN 1 DB
Range: 0.000 to 100.000% in steps of 0.001
Default: 0.000%
This setting specifies the deadband for the ANALOG IN 1 VALUE. The deadband is used to determine when to update the
deadbanded magnitude from the instantaneous magnitude. The deadband is a percentage of the difference between
the "max." and "min." values. Here, the "max." and "min." are as specified by the settings ANALOG IN 1 MAX and ANALOG IN
1 MIN.
See the Deadband Settings section earlier for a description of deadbanded values.
ANALOG IN 1 MIN
Default: 0.000
This setting specifies the "min." value used in deadband calculations. The scaling of this setting is the same as used by
<LDName>/GGIO4.AnIn01.instMag.f. This setting is stored as an IEEE 754 / IEC 60559 floating point number. Because of
the large range of this setting, not all possible values can be stored. Some values are rounded to the closest possible
floating point number.
ANALOG IN 1 MAX
Default: 1000000.000
This setting specifies the "max." value used in deadband calculations. The scaling of this setting is the same as used by
<LDName>/GGIO4.AnIn01.instMag.f. This setting is stored as an IEEE 754 / IEC 60559 floating point number. Because of
the large range of this setting, not all possible values can be stored. Some values are rounded to the closest possible
floating point number.

File transfer by IEC 61850

The B90 supports file transfer by IEC 61850. The approach is as follows, using the SISCO AX-S4 61850 client software as an
example.
1. In the AX-S4 61850 Explorer window, click the Tools menu and access the SISCO File Transfer Utility.
2. Select the Remote AR Name from the drop-down list. Available files appear in the File Specification area on the right
side of the window.
3. With the Copy option active, select a file to transfer and click the Go button. The file is copied and displays in the Local
list on the left side of the window.
4. Repeat the process to transfer any other files.
Figure 5-44: File transfer by IEC 61850
5.3.6.13 Web server HTTP protocol

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  WEB SERVER HTTP PROTOCOL
 WEB SERVER HTTP TCP PORT Range: 0 to 65535 in steps of 1
 HTTP PROTOCOL  NUMBER(80): 80
The B90 contains an embedded web server and can display pages in a web browser. The web pages are organized as a
series of menus that can be accessed starting at the B90 “Main Menu.” Web pages are read-only and are available
showing DNP and IEC 60870-5-104 points lists, Modbus registers, event records, fault reports, and so on. First connect the
B90 and a computer to an Ethernet network, then enter the IP address of the B90 Ethernet port in a web browser.
To close the port, set the port number to 0.
Any change takes effect when the B90 is restarted.

Figure 5-45: Example of UR web page showing event records
those protocols.
5.3.6.14 TFTP protocol

5
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  TFTP PROTOCOL
 TFTP PROTOCOL TFTP MAIN UDP PORT Range: 0 to 65535 in steps of 1
  NUMBER(69): 69
TFTP DATA UDP PORT 1 Range: 0 to 65535 in steps of 1

 NUMBER: 0
TFTP DATA UDP PORT 2 Range: 0 to 65535 in steps of 1

 NUMBER: 0
The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the B90 over a network. The B90 operates as a
TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file obtained
from the B90 contains a list and description of all available files, for example event records and oscillography.
The "put" function is not for security reasons. You can enter a "get" command but not a "put" command.
TFTP MAIN UDP PORT NUMBER — To close the port, set the port number to 0. Any change takes effect when the B90 is
restarted.
those protocols.
5.3.6.15 IEC 60870-5-104 protocol

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-104 PROTOCOL
 IEC 60870-5-104 IEC TCP PORT Range: 0 to 65535 in steps of 1
 PROTOCOL  NUMBER: 2404
 IEC NETWORK See below

  CLIENT ADDRESSES

IEC COMMON ADDRESS Range: 0 to 65535 in steps of 1

 OF ASDU: 0
IEC CYCLIC DATA Range: 1 to 65535 s in steps of 1

 PERIOD: 60 s
IEC CURRENT DEFAULT Range: 0 to 65535 in steps of 1

 THRESHOLD: 30000
IEC VOLTAGE DEFAULT Range: 0 to 65535 in steps of 1

IEC POWER DEFAULT Range: 0 to 65535 in steps of 1

IEC ENERGY DEFAULT Range: 0 to 65535 in steps of 1

IEC PF DEFAULT Range: 0.00 to 1.00

 THRESHOLD: 1.00
IEC OTHER DEFAULT Range: 0 to 65535 in steps of 1

IEC REDUNDANCY Range: No, Yes

 ENABLED: No
IEC 60870-5-104 is a transmission protocol for network access, specifically for communication between a control station
and substation over a TCP/IP network.
The B90 supports the IEC 60870-5-104 protocol. This protocol is enabled when the SETTINGS  PRODUCT SETUP 
COMMUNICATIONS  PROTOCOL setting is set to IEC 60870-5-104. The B90 can be used as an IEC 60870-5-104 slave device
5 connected to a maximum of two masters (usually either an RTU or a SCADA master station). Since the B90 maintains two
sets of IEC 60870-5-104 data change buffers, ideally no more than two masters actively communicate with the B90 at one
time.
The IEC ------- DEFAULT THRESHOLD settings are used to determine when to trigger spontaneous responses containing
M_ME_NC_1 analog data. These settings group the B90 analog data into types: current, voltage, power, energy, and other.
Each setting represents the default threshold value for all M_ME_NC_1 analog points of that type. For example, to trigger
spontaneous responses from the B90 when any current values change by 15 A, the IEC CURRENT DEFAULT THRESHOLD
setting is set to 15. Note that these settings are the default values of the deadbands. P_ME_NC_1 (parameter of measured
value, short floating point value) points can be used to change threshold values, from the default, for each individual
M_ME_NC_1 analog point. Whenever power is removed and re-applied to the B90, the default thresholds are in effect.
The IEC REDUNDANCY setting decides whether multiple client connections are accepted or not. If redundancy is set to Yes,
two simultaneous connections can be active at any given time.
IEC TCP PORT NUMBER — To close the port, set the port number to 0. Any change takes effect when the B90 is restarted.
IEC COMMON ADDRESS OF ASDU — The change takes effect when the B90 is restarted.
IEC CYCLIC DATA PERIOD — The change takes effect when the B90 is restarted.
The B90 relay does not support power metering. As such, the IEC POWER DEFAULT THRESHOLD setting is not
applicable.
The B90 relay does not support energy metering. As such, the IEC ENERGY DEFAULT THRESHOLD setting is not
applicable.
those protocols.

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-104 PROTOCOL  IEC NETWORK CLIENT
ADDRESSES
 IEC NETWORK CLIENT ADDRESS 1: Range: standard IPV4 address format
 CLIENT ADDRESSES  0.0.0.0

CLIENT ADDRESS 5: Range: standard IPV4 address format
 0.0.0.0
The B90 can specify a maximum of five clients for its IEC 104 connections. These are IP addresses for the controllers to
which the B90 can connect. A maximum of two simultaneous connections are supported at any given time.
5.3.6.16 IEC 60870-5-103 protocol

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-103
 IEC103 IEC103 COMMON Range: 0 to 254 in steps of 1
 PROTOCOL  ADDRESS OF ASDU: 0
IEC103 SYNC TIMEOUT: Range: 1 to 1440 min in steps of 1

 1
 IEC103 INPUTS See below

  BINARY
 IEC103 INPUTS See below

  MEASURANDS
 IEC103 COMMANDS See below

 
5
The B90 is provided with optional IEC 60870-5-103 communications capability. This feature is specified as a
software option at the time of ordering. See the Order Codes section in chapter 2 for details.
IEC 60870-5-103 is a companion standard to the IEC 60870-5 suite of standards for transmission protocols. It defines
messages and procedures for interoperability between protection equipment and devices of a control system in a
substation for communicating on a serial line.
The IEC 60870-5-103 protocol is enabled when the SETTINGS  PRODUCT SETUP  COMMUNICATIONS  PROTOCOL setting
is set to IEC 60870-5-103.
The IEC 60870-5-103 is an unbalanced (master-slave) protocol for coded-bit serial communication, exchanging
information with a control system. In the context of this protocol, the protection equipment is the slave and the control
system is the master. The communication is based on a point-to-point principle. The master must be able to interpret the
IEC 60870-5-103 communication messages.
The UR implementation of IEC 60870-5-103 consists of the following functions:
• Report binary inputs
• Report analog values (measurands)
• Commands
• Time synchronization
The RS485 port supports IEC 60870-5-103.
The UR Family Communications Guide contains more information on the protocol.
IEC103 COMMON ADDRESS OF ASDU — This setting uniquely defines this B90 on the serial line. Select an ID between 0 and
254. This ID does not need to be in sequential order for all stations that communicate with a controller, but it is
recommended. Note that RS485 only allows a maximum of 32 slave stations on a communication line, so the entire range
of 254 addresses is never exhausted.

IEC103 SYNC TIMEOUT — This setting defines the time that the B90 waits for a synchronization message. The B90
synchronizes its clock using all available sources, with the source synching more frequently overwriting the time of the
other sources. Since the synchronization message received from the IEC 60870-5-103 master is less frequent than IRIG-B,
PTP, or SNTP, its time is overwritten by these three sources, if any of them is active. If the synchronization timeout occurs
and none of IRIG-B, PTP, or SNTP is active, the B90 sets the invalid bit in the time stamp of a time-tagged message.
The settings for the remaining menus are outlined as follows.
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-103  IEC103 INPUTS BINARY
 IEC103 INPUTS  POINT 0 See below
 BINARY  
 POINT 1 See below

 

 POINT 95 See below
 
 POINT 0 POINT 0 FUN Range: 0 to 255 in steps of 1

  0
POINT 0 INF Range: 0 to 255 in steps of 1

 0
POINT 0 Input Range: FlexLogic operand

 Off
5 
 POINT 95 POINT 95 FUN Range: 0 to 255 in steps of 1
  0
POINT 95 INF Range: 0 to 255 in steps of 1

 0
POINT 95 Input Range: FlexLogic operand

 Off
The binary input points are mapped using elements from a list of possible FlexLogic operands. A maximum of 96 binary
inputs (points) can be mapped this way.
The IEC 60870-5-103 point list always starts with point 0 and ends at the first "Off" value. Since the IEC 60870-5-103 point
list must be in a continuous block, any points assigned after the first "Off" point are ignored.
For each defined point, set appropriate values for the Function Type (FUN) and Information Number (INF), which form the
Information Object Identifier field of the ASDU, as defined in IEC 60870-5-103.
The binary input points are sent as Class 1 data. They are sent either as a response to a general interrogation received
from the controller or reported spontaneously. Spontaneous transmission occurs as a response to cyclic Class 2 requests.
If the B90 wants to transmit Class 1 data at that time, it demands access for Class 1 data transmission (ACD=1 in the
control field of the response).
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-103  IEC103 INPUTS MEASURANDS

 IEC103 INPUTS  ASDU 1 See below
 MEASURANDS  

 ASDU 4
 

 ASDU 1 ASDU 1 TYP: Range: 3 or 9

  9
ASDU 1 FUN: Range: 0 to 255 in steps of 1

 0
ASDU 1 INF: Range: 0 to 255 in steps of 1

 0
ASDU 1 SCAN TOUT: Range: 0 to 1000 s in steps of 1

 0
ASDU 1 ANALOG 1 Range: FlexAnalog parameter

 Off
ASDU 1 ANALOG 1 Range: 0.000 to 65.535 in steps of 0.001

 FACTOR: 1.000
ASDU 1 ANALOG 1 Range: -32768 to 32767 in steps of 1

 OFFSET: 0

 Off

 FACTOR: 1.000

 OFFSET: 0
 5
 ASDU 4 ASDU 4 TYP: Range: 3 or 9
  9
ASDU 4 FUN: Range: 0 to 255 in steps of 1

 0
ASDU 4 INF: Range: 0 to 255 in steps of 1

 0
ASDU 4 SCAN TOUT: Range: 0 to 1000 s in steps of 1

 0

 Off

 FACTOR: 1.000

 OFFSET: 0

 Off

 FACTOR: 1.000

 OFFSET: 0
The configuration menu allows a maximum of four ASDUs containing measurands.

Measurands are sent as a response to Class 2 requests, which are cyclic requests coming from the master.

TYPE IDENTIFICATION (TYP) — The configuration field TYP indicates how many measurands are present in the corresponding
ASDU. Each ASDU can take either 4 or 9 measurands maximum, depending on the type identification (3 respectively 9). For
any change to take effect, restart the relay.
FUNCTION TYPE (FUN) and INFORMATION NUMBER (INF) — These two fields form the Information Object Identifier of the ASDU
as defined in IEC 60870-103. For any change to take effect, restart the relay.
SCAN TIMEOUT (SCAN TOUT) — This is the cyclic period used by the B90 to decide when a measurand ASDU is included in a
response. The measurand is sent as response to a Class 2 request when the corresponding timeout expires. The default
value 0 means 500 ms.
ANALOG # — This field contains the actual measurand to be sent in the response to the master. The measurands can be
mapped using elements from a list of FlexAnalog operands. The measurands sent are voltage, current, power, power
factor, and frequency. If any other FlexAnalog is chosen, the B90 sends 0 instead of its value. Note that the power is
transmitted in KW, not W. Measurands are transmitted as ASDU 3 or ASDU 9 (type identification value set to measurands I,
respectively measurands II).
Each IEC 60870-5-103 measurands list ends at the first unconfigured ("Off") value. Any measurand assigned after the first
"Off" value is ignored.
At least one measurand per ASDU must be configured in order to configure the following ASDU. For example, the user can
configure only one measurand for each ASDU, but the user is not allowed to skip ASDU 2 and configure measurands in
ASDU 3.
ANALOG # FACTOR and OFFSET — For each measurand included in the ASDU, a factor and offset also can be configured. The
factor and offset allow for scaling to be performed on measurands. The final measurement sent to the IEC 60870-103
master is then "a*x + b," where x is the measurand, a is the multiplying factor and b is the offset. The master has to perform
the reversed operation in order to retrieve the actual value if such scaling is done. By default a = 1 and b = 0, so no scaling
5 is done if these values are left at their defaults. Examples of when scaling is appropriate are as follows:
• If the measured value contains decimals and it is important to preserve the resolution. Since the format for
transmitting the measurand does not permit decimals, a factor a>1 can be applied before transmission. For example,
a frequency F=59.9Hz can be transmitted as Ft = 10 * F = 10 * 59.9 = 599. In this case a = 10, b = 0. The master receives
599 and has to divide by 10 to retrieve the real value 59.9.
• If the measured value is larger than what fits in the format defined in IEC 103. The format defined in the standard
allows for signed integers up to 4095. By offsetting, unsigned integers up to 4096 + 4095 = 8191 are supported.
Scaling using factors <1 can be required in such cases. The calculation is outlined in the IEC 60870-5-103 chapter of
the UR Family Communications Guide. Two examples follow, where you decide factors a and b.
Example 1: Nominal power Pn = 100 MW = 100000 KW (power is transmitted in KW)
Since P can be both positive and negative:
Transmitted power Pt = (4095/(Pn*2.4)) * P = (4095/(100000 * 2.4) ) * P
= 0.017 * P
a = 0.017
b=0
Pt = 0.017 * P
For a max power 100000 KW * 2.4 = 240000 KW, we transmit
Pt = 0.017 * 240000 = 4080
A value above 240 MW is indicated by overflow.
Example 2: Nominal voltage Vn = 500000 V

Since RMS voltage V can be only positive:
Transmitted voltage Vt = (8191/(Vn*2.4)) * V - 4096 =
= (8191/(500000 * 2.4) ) * V - 4096 = 0.0068 * V - 4096
a = 0.0068
Since the step is in increments of 0.001, we round it at:

a = 0.006
b = -4096
Vt = 0.006 * V - 4096
For max voltage 500000 V * 2.4 = 1200000 V, we transmit
Vt = 0.006 * 1200000 - 4096 = 7200 - 4096 = 3104
SETTINGS  PRODUCT SETUP  COMMUNICATIONS  IEC 60870-5-103  IEC103 COMMANDS

 IEC103 COMMANDS  COMMAND 0 See below
  
 COMMAND 1
 

 COMMAND 31
 
 COMMAND 0 COMMAND 0 FUN: Range: 0 to 255 in steps of 1

  0
COMMAND 0 INF: Range: 0 to 255 in steps of 1

 0
COMMAND 0 ON: Range: Virtual input

 Off
COMMAND 0 OFF: Range: Virtual input

5
 Off

 COMMAND 31 COMMAND 31 FUN: Range: 0 to 255 in steps of 1
  0
COMMAND 31 INF: Range: 0 to 255 in steps of 1

 0
COMMAND 31 ON: Range: Virtual input

 Off
COMMAND 31 OFF: Range: Virtual input

 Off
Commands are received as General Command (Type Identification 20). The user can configure the action to perform when
an ASDU command comes.
A list of available mappings is provided on the B90. This includes 64 virtual inputs (see the following table). The ON and OFF
for the same ASDU command can be mapped to different virtual inputs.
Each command is identified by the unique combination made by the function type (FUN) and information number (INF). If
the master sends an ASDU command that does not have the FUN and INF of any configured command, the relay rejects it.
Table 5-12: Commands mapping table
Description Value
Off 0
Virtual Input 1 1
Virtual Input 2 2
... ...
Virtual Input 64 64

5.3.6.17 USB port

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  USB 2.0
 USB 2.0 USB DEVICE PORT Range: Disabled, Enabled
  FUNCTION: Enabled
This setting applies to the USB port on the graphical front panel.
This setting enables/disables the USB port on the graphical front panel. When the port function is "Enabled," a standard
USB serial cable allows a computer running the EnerVista UR Setup software to retrieve, display, and write settings either
individually or collectively, to display status and actual values, to initiate controls, and to retrieve and display event records,
oscillography records, data logger records, and disturbance records. Installation of the EnerVista software automatically
installs the drivers required to use this USB port.
DNP is not available using the USB port on the graphical front panel.
5.3.7 Modbus user map

SETTINGS  PRODUCT SETUP  MODBUS USER MAP
 MODBUS USER MAP ADDRESS 1: 0 Range: 0 to 65535 in steps of 1
  VALUE: 0
5 
ADDRESS 256: 0 Range: 0 to 65535 in steps of 1
 VALUE: 0
The Modbus user map provides read-only access for up to 256 registers. To obtain a memory map value, enter the address
in the ADDRESS line (converted from hex to decimal format). The corresponding value (if programmed) displays in the VALUE
line. A value of “0” in subsequent register ADDRESS lines automatically returns values for the previous ADDRESS lines
incremented by 1. An address value of “0” in the initial register means “none” and values of “0” display for all registers.
Different ADDRESS values can be entered as required in any of the register positions.
The UR Family Communications Guide outlines the Modbus memory map. The map is also viewable in a web browser;
enter the IP address of the B90 in a web browser and click the option.
5.3.8 Real-time clock
5.3.8.1 Menu
SETTINGS  PRODUCT SETUP  REAL TIME CLOCK
 REAL TIME SYNCRONIZING SOURCE: Range: None, PP/IRIG-B/PTP/Other, IRIG-B/PP/PTP/
 CLOCK  None Other, PP/PTP/IRIG-B/Other
REAL TIME CLOCK Range: Enabled, Disabled

 EVENTS: Disabled
IRIG-B SIGNAL TYPE: Range: None, DC Shift, Amplitude Modulated

 None
 PRECISION TIME See below

  PROTOCOL (1588)
 SNTP PROTOCOL See below

 

 LOCAL TIME See below

 
The relay contains a real time clock (RTC) to create time stamps for communications protocols as well as for historical data,
such as event records and oscillography. When the relay restarts, the RTC initializes from an onboard battery-backed
clock, which has the same accuracy as an electronic watch, approximately ±1 minute per month (~23 ppm). Once the RTC
is synchronized with the Precision Time Protocol (PTP), IRIG-B, or SNTP, its accuracy approaches that of the synchronizing
time delivered to the relay. While the RTC is not synchronized via PTP or IRIG-B, or the relay determines that it has an offset
possibly greater than 10 µs from the international time standard, the CLOCK UNSYNCHRONIZED FlexLogic operand is
activated.
The SYNCHRONIZING SOURCE setting displays in the software when the relay includes the IEEE 1588 software option. The
setting configures the priority sequence of the time synchronization source, to determine which of the available external
time sources to use for time synchronization. A setting of None causes the RTC and the synchrophasor clock to free-run,
and the clock can be changed from the front panel or from communications protocols. A setting of PP/IRIG-B/PTP/Other,
IRIG-B/PP/PTP/Other, or PP/PTP/IRIG-B/Other causes the relay to track the first source named that is enabled and
operational, or free-run if none of these are available. Here, PP means a time source that is strictly compliant with PP, PTP
means a time source that is not strictly compliant with PP, and Other means any less precise source (SNTP, IEC 103, IEC 104,
Modbus, or DNP). When a time source fails or recovers, the relay automatically transfers synchronization as required by
this setting.
When the relay does not have the IEEE 1588 software option and this setting does not display, it uses IRIG-B when enabled
and operational, then failing that SNTP when configured and operational, and otherwise it free-runs unless the clock is
changed from the front panel or from communications protocols.
Setup for IRIG-B is illustrated in the Installation chapter.
For the Other protocols, whenever a time synchronization message is received through any of the active protocols, the B90
clock updates. However, given that IEC 60870-5-103, IEC 60870-5-104, Modbus, and DNP are low-accuracy time
synchronization methods, avoid their use for synchronization when better accuracy time protocols, such as IRIG-B and PTP,
5
are active in the system. If IRIG-B or PTP is used to update the relay clock, the other protocols (such as SNTP) are not
allowed to update, even if active.
See the COMMANDS  SET DATE AND TIME menu section of this manual to manually set the RTC.
The REAL TIME CLOCK EVENTS setting allows changes to the date and/or time to be captured in the event record. The event
records the RTC time before the adjustment. A Date/Time Changed event is generated when:
• The real time clock changed from SNTP/PTP/IRIG-B and the time difference is more than one second
• The real time clock changed from the front panel or via Modbus register. The relay always generates this event
regardless of the time difference.
• The Daylight Saving Time (DST) setting gets enabled and the current relay time is already in the DST zone
• The real time clock enters or leaves DST
To enable IRIG-B synchronization, the input IRIG-B SIGNAL TYPE must be set to DC Shift or Amplitude Modulated. IRIG-B
synchronization can be disabled by making this setting None.
Clocks can be synchronized locally among several relays using the computer time. When using a time source, such as IRIG-
B, the time is overwritten eventually by the time source. To synchronize clocks among UR devices:
1. In the EnerVista software, expand the main menu in the Online Window area and select the Synchronize Devices
entry. The window opens. The software prompts to acknowledge any offline devices.
2. Click the Synchronize Devices button at the top of the window, and confirm the action at the prompt. The devices
assume the time of the computer being used.
To configure and enable PTP and/or SNTP, or to set local time parameters (for example time zone, daylight savings), use the
following sections.

5.3.8.2 Precision time protocol (1588)

SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  PRECISION TIME PROTOCOL (1588)
 PRECISION TIME STRICT POWER Range: Enabled, Disabled
 PROTOCOL (1588)  PROFILE: Disabled
PTP DOMAIN NUMBER: Range: 0 to 255

 0
PTP VLAN PRIORITY: Range: 0 to 7

 4
PTP VLAN ID: Range: 0 to 4095

 0
 PTP PORT 1 See below

 
SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  PRECISION TIME PROTOCOL (1588)  PTP PORT 1(3)
 PTP PORT 1 PORT 1 PTP FUNCTION: Range: Enabled, Disabled
  Disabled
PORT 1 PATH DELAY Range: 0 to 60000 ns in steps of 1

 ADDER: 0 ns
PORT 1 PATH DELAY Range: –1000 to +1000 ns in steps of 1

 ASYMMETRY: 0 ns
The B90 is provided with optional Precision Time Protocol capability. This feature is specified as the IEEE 1588
5 software option at the time of ordering. See the Order Codes section in chapter 2 for details.
The B90 supports the Precision Time Protocol (PTP) specified in IEEE Std 1588 2008 using the Power Profile (PP) specified in
IEEE Std C37.238 2011. This enables the relay to synchronize to the international time standard over an Ethernet network
that implements PP.
The relay can be configured to operate on some PTP networks that are not strictly PP. Time accuracy can be less than
specified for a PP network. Tolerated deviations from strict PP include 1) missing declaration of PP compliance in the
messages, 2) connection to a network device that does not support the PTP peer delay mechanism, 3) jitter substantially
greater than 1 µs in received event messages, and 4) certain non-compliant announce and sync message update rates.
The relay implements PTP according to IEEE Std 1588 2008 and the equivalent IEC 61588:2009(E), sometimes referred to as
version 2 PTP. It does not support the previous version of the standard (version 1).
PTP is a protocol that allows multiple clocks in a network to synchronize with one another. It permits synchronization
accuracies better than 1 ns, but this requires that each and every component in the network achieve very high levels of
accuracy and a very high baud rate, faster than normally used for relay communications. When operating over a generic
Ethernet network, time error can amount to 1 ms or more. PP is a profile of PTP which specifies a limited subset of PTP
suitable for use in power system protection, control, automation, and data communication applications, and thereby
facilitates interoperability between different vendor’s clocks and switches. PP specifies a worst-case delivered time error of
less than 1 µs over a 16-hop network.
In a PTP system and in a PP system, the clocks automatically organize themselves into a master-slave synchronization
hierarchy with the “best” clock available making itself the "grandmaster" at the top of the hierarchy; all others make
themselves “slaves” and track the grandmaster. Typically the grandmaster clock receives its time from GPS satellites or
some other link to the international time standard. If the grandmaster fails, the next “best” clock available in the domain
assumes the grandmaster role. When a clock on start-up discovers that it is “better” than the present grandmaster, it
assumes the grandmaster role and the previous grandmaster reverts to slave. The B90 qualification mechanism accepts a
potential master clock as a new grandmaster, when in a four-second interval it has received three announce messages
from it, all better than the present grandmaster clock and better than any other announce in this interval.

Time messages issued by the grandmaster are delayed as they pass through the network both due to the finite speed of
the signal in the interconnecting fiber or wire, and due to processing delays in the Ethernet switches. Each clock and switch
implementing PP measures the propagation delay to each of its PP neighbors, and compensates for these delays in the
time received. Each network device implementing PP measures the processing delay it introduces in each time message
and compensates for this delay in the time it transmits. As a result, the time delivered to end-devices such as the UR are
virtually identical to the grandmaster time. If one of the network devices in the hierarchy does not fully implement PP, the
associated propagation delay and/or latency may not be compensated for, and the time received at the end-device can be
in error by more than 100 µs.
See the preceding Real Time Clock section for a description of when time values received via PTP are used to update the
relay’s real time clock.
The following settings are available for configuring the relay for PTP. The PTP menu displays only when the option was
purchased.
STRICT POWER PROFILE — Power profile (IEEE Std C37.238 2011) requires that the relay only select a power profile compliant
clock as a grandmaster, that the delivered time have worst-case error of ±1 µs, and that the peer delay mechanism be
implemented. With the strict power profile setting enabled, the relay only selects as master the clocks displaying the
IEEE_C37_238 identification codes. It uses a port only when the peer delay mechanism is operational. With the strict power
profile setting disabled, the relay uses clocks without the power profile identification when no power profile clocks are
present, and uses ports even if the peer delay mechanism is non-operational. This setting applies to all of the relay’s PTP
capable ports.
PTP DOMAIN NUMBER — Set this setting to the domain number of the grandmaster-capable clock(s) to be synchronized to. A
network can support multiple time distribution domains, each distinguished with a unique domain number. More
commonly, there is a single domain using the default domain number zero.
This setting applies to all of the relay’s PTP capable ports.
PTP VLAN PRIORITY — This setting selects the value of the priority field in the 802.1Q VLAN tag in request messages issued
by the relay’s peer delay mechanism. In compliance with PP the default VLAN priority is 4, but it is recommended that it be
5
set to 7 in accordance with PTP. Depending on the characteristics of the device to which the relay is linked directly, VLAN
Priority can have no effect.
This setting applies to all of the relay’s PTP capable ports.
PTP VLAN ID — This setting selects the value of the ID field in the 802.1Q VLAN tag in request messages issued by the relay’s
peer delay mechanism. It is provided in compliance with PP. As these messages have a destination address that indicates
they are not to be bridged, their VLAN ID serves no function, and so can be left at its default value. Depending on the
characteristics of the device to which the relay is linked directly, VLAN ID can have no effect. This setting applies to all of
the relay’s PTP capable ports.
PORT 1 ... 3 FUNCTION — While this port setting is selected to disabled, PTP is disabled on this port. The relay does not
generate or listen to PTP messages on this port.
PORT 1 ... 3 PATH DELAY ADDER — The time delivered by PTP is advanced by the time value in this setting prior to the time
being used to synchronize the relay’s real time clock. This is to compensate to the extent practical for time delivery delays
not compensated for in the network. In a fully compliant PP network, the peer delay and the processing delay mechanisms
compensate for all the delays between the grandmaster and the relay. In such networks, make this setting zero.
In networks containing one or more switches and/or clocks that do not implement both of these mechanisms, not all
delays are compensated, so the time of message arrival at the relay is later than the time indicated in the message. This
setting can be used to approximately compensate for this delay. However, as the relay is not aware of network switching
that dynamically changes the amount of uncompensated delay, there is no setting that always and completely corrects
for uncompensated delay. A setting can be chosen that reduces the worst-case error to half of the range between
minimum and maximum uncompensated delay, if these values are known.
PORT 1 ... 3 PATH DELAY ASSYMMETRY — This setting corresponds to “delayAsymmetry” in PTP, which is used by the peer delay
mechanism to compensate for any difference in the propagation delay between the two directions of a link. Except in
unusual cases, the two fibers are of essentially identical length and composition, so make this setting zero.

In unusual cases where the length of the link is different in different directions, set this setting to the number of
nanoseconds the Ethernet propagation delay to the relay is longer than the mean of path propagation delays to and from
the relay. For instance, if it is known say from the physical length of the fibers and the propagation speed in the fibers that
the delay from the relay to the Ethernet switch it is connected to is 9000 ns and that the delay from the switch to the relay
is 11000 ns, then the mean delay is 10000 ns, and the path delay asymmetry is 11000 - 10000 = +1000 ns.
5.3.8.3 SNTP protocol

SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  SNTP PROTOCOL
 SNTP PROTOCOL SNTP FUNCTION: Range: Enabled, Disabled
  Disabled
SNTP SERVER1 IP Range: standard IP address format

 ADDR: 127.0.0.1
SNTP SERVER2 IP Range: standard IP address format

 ADDR: 127.0.0.1
SNTP SERVER1 UDP Range: 0 to 65535 in steps of 1

 PORT: 123
SNTP SERVER2 UDP Range: 0 to 65535 in steps of 1

 PORT: 123
The B90 supports the Simple Network Time Protocol specified in RFC-2030. With SNTP, the B90 can obtain clock time over
an Ethernet network. The B90 acts as an SNTP client to receive time values from redundant SNTP/NTP servers, usually a
dedicated product using a GPS receiver to provide an accurate time. One or two SNTP servers can be used; use of both
servers for redundancy is recommended but not required.
5 To use SNTP, enable the function and set SNTP SERVER1 IP ADDR and/or SNTP SERVER2 IP ADDR to the SNTP/NTP server IP
addresses. The B90 attempts to obtain time values from the SNTP SERVER1 SNTP/NTP server. If SERVER1 is not available/
reachable, the B90 switches to the SNTP SERVER2 to get the time value and vice versa.
Since many time values are obtained and averaged, it generally takes three to four minutes until the B90 clock is closely
synchronized with the SNTP/NTP server. It can take up to 20 minutes for the B90 to signal an SNTP self-test error if the
server is offline, depending on the number and SNTP server modes. Broadcast mode timeout is 10 minutes and unicast
timeout is 80 seconds (corresponds to three unicast request retries).
SNTP FUNCTION — Enables or disables the SNTP feature on the B90.
SNTP SERVER1 IP ADDR — The B90 uses the SERVER1 address to contact an SNTP/NTP server to obtain time values. When
the SNTP FUNCTION setting is set to enabled or on startup if the setting is enabled, the B90 SNTP client requests SERVER1 for
the time value. If the SERVER1 channel fails or is not reachable, the B90 switches to SERVER2 SNTP/NTP server.
If SERVER1 SNTP server is set to 127.0.0.1, the B90 considers the SERVER1 SNTP server to be unconfigured.
To use SERVER1 SNTP in broadcast mode, set the SNTP SERVER1 IP ADDR setting to "0.0.0.0" and SNTP FUNCTION to "Enabled."
The B90 SNTP client then listens to SNTP messages sent to the "all ones" broadcast address for the subnet. The B90 waits
up to 18 minutes (>1024 seconds) without receiving an SNTP broadcast message before switching to the alternate
channel.
SNTP SERVER2 IP ADDR — The B90 uses this address to contact an SNTP/NTP server if SERVER1 channel fails or is not
reachable. If SERVER2 SNTP server is set to 127.0.0.1, the B90 considers the SERVER2 SNTP server to be unconfigured.
To use SERVER2 SNTP in broadcast mode, set the SNTP SERVER2 IP ADDR setting to "0.0.0.0" and SNTP FUNCTION to "Enabled."
The B90 SNTP client then listens to SNTP messages sent to the "all ones" broadcast address for the subnet. The B90 waits
up to 18 minutes (>1024 seconds) without receiving an SNTP broadcast message before switching to the alternate
channel.
SNTP SERVER1 UDP PORT — This setting is 123 for normal SNTP operation. If SERVER1 SNTP is not required, close the port by
changing this setting to zero.
SNTP SERVER2 UDP PORT — This setting is 123 for normal SNTP operation. If SERVER2 SNTP is not required, close the port by
changing this setting to zero.

those protocols.
If SERVER1 IP ADDR and UDP PORT settings match the SERVER2 IP ADDR and UDP PORT settings, the B90 considers only
the SERVER1 SNTP server as being configured and an SNTP Failure error message generates. The failure message
also displays when both servers are unavailable.
5.3.8.4 Local time

SETTINGS  PRODUCT SETUP  REAL TIME CLOCK  LOCAL TIME
 LOCAL TIME LOCAL TIME OFFSET Range: –24.0 to 24.0 hr in steps of 0.5
  FROM UTC: 0.0 hr
DAYLIGHT SAVINGS Range: Disabled, Enabled

 TIME: Disabled
DST START MONTH: Range: January to December (all months)

 January
DST START DAY: Range: Sunday to Saturday (all days of the week)
 Sunday
DST START DAY Range: First, Second, Third, Fourth, Last

 INSTANCE: First
DST START HOUR: Range: 0:00 to 23:00 in steps of one hour

 2:00
DST STOP MONTH: Range: January to December (all months)

 January
DST STOP DAY: Range: Sunday to Saturday (all days of the week)
5
 Sunday
DST STOP DAY Range: First, Second, Third, Fourth, Last

 INSTANCE: First
DST STOP HOUR: Range: 0:00 to 23:00 in steps of one hour

 2:00
The B90 maintains two times: local time and Universal Coordinated Time (UTC). Local time can be provided by IRIG-B
signals. UTC time is provided by SNTP servers.
The real-time clock (RTC) and time stamps reported in historical records and communication protocols can be incorrect if
the Local Time settings are not configured properly.
See the IRIG-B section in the Installation chapter for guidance on these settings when using an IRIG-B source that sets the
IRIG-B control bits according to IEEE Std 1344-1995.
LOCAL TIME OFFSET FROM UTC — Used to specify the local time zone offset from UTC (Greenwich Mean Time) in hours. Time
zones in the eastern hemisphere have positive values; time zones in the western hemisphere have negative values. A value
of zero causes the relay to use UTC for local time. This setting has two uses. When the system RTC is synchronized with a
communications protocol providing only local time or it is free-running, the offset setting is used to calculate UTC from the
local time these provide. When the RTC is synchronized with a communications protocol providing only UTC (such as PTP or
SNTP), the time offset setting is used to determine local time from the UTC provided. PTP
ALTERNATE_TIME_OFFSET_INDICATOR TLVs are not used to calculate local time.
DAYLIGHT SAVINGS TIME and DST — Can be used to allow the relay to follow the DST rules of the local time zone. Note that
when IRIG-B time synchronization is active, the local time in the IRIG-B signal contains any daylight savings time offset and
so the DST settings are ignored.

5.3.9 User-programmable fault report

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE FAULT REPORTS  USER-PROGRAMMABLE FAULT REPORT
1(2)
 USER-PROGRAMMABLE FAULT REPORT 1 Range: Disabled, Enabled
 FAULT REPORT 1  FUNCTION: Disabled
PRE-FAULT 1 TRIGGER: Range: FlexLogic operand

 Off
FAULT 1 TRIGGER: Range: FlexLogic operand

 Off
FAULT REPORT 1 # 1: Range: Off, any actual value analog parameter

 Off

FAULT REPORT 1 #32: Range: Off, any actual value analog parameter
 Off
When enabled, this function monitors the pre-fault trigger. The pre-fault data are stored in the memory for prospective
creation of the fault report on the rising edge of the pre-fault trigger. The element waits for the fault trigger as long as the
pre-fault trigger is asserted, but not shorter than 1 second. When the fault trigger occurs, the fault data is stored and the
complete report is created. If the fault trigger does not occur within 1 second after the pre-fault trigger drops out, the
element resets and no record is created.
The user programmable record contains the following information: the user-programmed relay name, detailed firmware
revision (x.xx, for example) and relay model (B90), the date and time of trigger, the name of pre-fault trigger (a specific
FlexLogic operand), the name of fault trigger (a specific FlexLogic operand), the active setting group at pre-fault trigger, the
5 active setting group at fault trigger, pre-fault values of all programmed analog channels (one cycle before pre-fault trigger),
and fault values of all programmed analog channels (at the fault trigger).
Each fault report is stored as a file to a maximum capacity of ten files. An eleventh trigger overwrites the oldest file. The
EnerVista software is required to view all captured data. A FAULT RPT TRIG event is automatically created when the report
is triggered.
The relay includes two user-programmable fault reports to enable capture of two types of trips (for example, trip from
thermal protection with the report configured to include temperatures, and short-circuit trip with the report configured to
include voltages and currents). Both reports feed the same report file queue.
The last record is available as individual data items via communications protocols.
PRE-FAULT 1 TRIGGER — Specifies the FlexLogic operand to capture the pre-fault data. The rising edge of this operand stores
one cycle-old data for subsequent reporting. The element waits for the fault trigger to actually create a record as long as
the operand selected as PRE-FAULT 1 TRIGGER is “On.” If the operand remains “Off” for 1 second, the element resets and no
record is created.
FAULT 1 TRIGGER — Specifies the FlexLogic operand to capture the fault data. The rising edge of this operand stores the
data as fault data and results in a new report. The trigger (not the pre-fault trigger) controls the date and time of the
report.
FAULT REPORT 1 #1 to FAULT REPORT 1 #32 — These settings specify an actual value such as voltage or current magnitude,
true RMS, phase angle, frequency, temperature, and so on, to be stored when the report is created. Up to 32 channels can
be configured. Two reports are configurable to cope with variety of trip conditions and items of interest.
5.3.10 Oscillography
5.3.10.1 Menu
SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY
 OSCILLOGRAPHY NUMBER OF RECORDS: Range: 1 to 64 in steps of 1
  15

TRIGGER MODE: Range: Automatic Overwrite, Protected

 Automatic Overwrite
TRIGGER POSITION: Range: 0 to 100% in steps of 1

 50%
TRIGGER SOURCE: Range: FlexLogic operand

 Off
AC INPUT WAVEFORMS: Range: Off; 8, 16, 32, 64 samples/cycle

 16 samples/cycle
 DIGITAL CHANNELS See below

 
 ANALOG CHANNELS See below

 
Oscillography records contain waveforms captured at the sampling rate as well as other relay data at the point of trigger.
Oscillography records are triggered by a programmable FlexLogic operand. Multiple oscillography records can be captured
simultaneously.
To retrieve an Oscillography record from a relay:
1. If not yet set up for oscillography, configure settings under Settings > Product Setup > Oscillography in the EnerVista
software.
2. Access Actual Values > Records > Oscillography in the EnerVista software.
3. In the window that opens, select the record number. The highest number is the most recent record (Newest Record
Number).
4. Click the Read button to get the waveform. When available, waveforms are displayed graphically, and otherwise error
messages display. 5
5. In the waveform window that opens, you can save the file, for example with the CFG extension.
The NUMBER OF RECORDS is selectable, but the number of cycles captured in a single record varies considerably based on
other factors, such as sample rate and the number of operational modules. There is a fixed amount of data storage for
oscillography; the more data captured, the less the number of cycles captured per record. See the ACTUAL VALUES 
RECORDS  OSCILLOGRAPHY menu to view the number of cycles captured per record. The following table provides sample
configurations with corresponding cycles/record. The minimum number of oscillographic records is three.
Table 5-13: Oscillography cycles/record example
Records CT/VTs Sample rate Digital Analog Cycles per
channels channels record
3 1 32 32 16 2399
3 1 64 32 16 1450
16 1 32 32 16 666
16 1 64 32 16 402
32 1 32 32 16 352
32 1 64 32 16 213
3 2 32 32 16 1516
3 2 64 32 16 851
16 2 32 32 16 421
TRIGGER MODE — A new record automatically overwrites an older record when TRIGGER MODE is set to “Automatic
Overwrite.”
TRIGGER POSITION — Set this to a percentage of the total buffer size (for example, 10%, 50%, 75%, and so on). A trigger
position of 25% consists of 25% pre- and 75% post-trigger data.
TRIGGER SOURCE — Always captured in oscillography and can be any FlexLogic parameter (element state, contact input,
virtual output, and so on). The relay sampling rate is 64 samples per cycle.

AC INPUT WAVEFORMS — Determines the sampling rate at which AC input signals (that is, current and voltage) are stored.
Reducing the sampling rate allows longer records to be stored. This setting has no effect on the internal sampling rate of
the relay, which is always 64 samples per cycle. That is, it has no effect on the fundamental calculations of the device.
When changes are made to the oscillography settings, all existing oscillography records are cleared.
5.3.10.2 Digital channels

SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  DIGITAL CHANNELS
 DIGITAL CHANNELS DIGITAL CHANNEL 1: Range: FlexLogic operand
  Off

DIGITAL CHANNEL 63: Range: FlexLogic operand
 Off
DIGITAL 1(63) CHANNEL — This setting selects the FlexLogic operand state recorded in an oscillography trace. The length of
each oscillography trace depends in part on the number of parameters selected here. Parameters set to “Off” are ignored.
To populate quickly the rows in the Offline Window, use Ctrl C/V to copy/paste, or click then double-click a row to display a
quick selection window.
Figure 5-46: Quick selection window
5.3.10.3 Analog channels

SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  ANALOG CHANNELS
 ANALOG CHANNELS ANALOG CHANNEL 1: Range: Off, any FlexAnalog/actual value parameter
  Off See Appendix A for list

ANALOG CHANNEL 16: Range: Off, any FlexAnalog/actual value parameter
 Off See Appendix A for list
These settings select the metering actual value recorded in an oscillography trace. The length of each oscillography trace
depends in part on the number of parameters selected here. Parameters set to “Off” are ignored. The parameters available
in a given relay depend on
• the type of relay,
• the type and number of CT/VT hardware modules installed, and
• the type and number of analog input hardware modules installed
A list of all possible analog metering actual value parameters is presented in Appendix A: FlexAnalog Parameters. The
parameter index number shown in any of the tables is used to expedite the selection of the parameter on the relay display.
It can be time-consuming to scan through the list of parameters via the relay keypad and display — entering this number
via the relay keypad causes the corresponding parameter to display.
If there are no CT/VT modules and analog input modules, no analog traces appear in the file; only the digital traces appear.

5.3.11 User-programmable LEDs
5.3.11.1 Menu - Enhanced and basic front panels

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS
 USER-PROGRAMMABLE  LED TEST See below
 LEDS  
 TRIP & ALARM LEDS See page 5-112

 

  LED 1

 USER-PROGRAMMABLE
  LED 48
5.3.11.2 Menu - Graphical front panel

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS
 USER-PROGRAMMABLE  LED TEST See below
 LEDS  
 TRIP & ALARM LEDS See page 5-112

 
 EVENT CAUSE LED 1 See page 5-113

 
5

 EVENT CAUSE LED 9
 
The LEDs can be customized to illuminate when a selected FlexLogic operand is in the logic 1 state. The trip and alarm
LEDs can also be customized in a similar manner. To ensure correct functionality of all LEDs, an LED test feature is also
provided.
5.3.11.3 LED test

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  LED TEST
 LED TEST LED TEST FUNCTION: Range: Disabled, Enabled
  Disabled
LED TEST CONTROL: Range: FlexLogic operand

 Off
When enabled, the LED test can be initiated from any digital input or user-programmable condition, such as a user-
programmable pushbutton. The control operand is configured under the LED TEST CONTROL setting. The test covers all
LEDs, including the LEDs of the optional user-programmable pushbuttons.
For the enhanced and basic front panels, the test consists of the following three stages:
1. All 62 LEDs on the relay are illuminated. This is a quick test to verify if any of the LEDs is “burned.” This stage lasts as
long as the control input is on, up to a maximum of one minute. After one minute, the test ends.
2. All the LEDs are turned off, and then one LED at a time turns on for one second, then back off. The test routine starts at
the top left panel, moving from the top to bottom of each LED column. This test checks for hardware failures that lead
to more than one LED being turned on from a single logic point. This stage can be interrupted at any time.
3. All the LEDs are turned on. One LED at a time turns off for one second, then back on. The test routine starts at the top
left panel moving from top to bottom of each column of the LEDs. This test checks for hardware failures that lead to
more than one LED being turned off from a single logic point. This stage can be interrupted at any time.

For the graphical front panel, the test consists of the following stages:
1. All 22 LEDs on the relay are illuminated. This is a quick test to verify if any of the LEDs is "burned." This stage lasts as
long as the control input is on, up to a maximum of one minute. After one minute, the test ends.
2. All the LEDs are turned off, and then one LED at a time turns on with the orange color for one second, then back off.
The test routine starts at the top left panel, moving from the top to bottom for all 14 LEDs. Then the eight pushbutton
LEDs are tested in the same manner. This test checks for hardware failures that lead to more than one LED being
turned on from a single logic point. This stage can be interrupted at any time.
3. All the LEDs are turned on with the orange color. One LED at a time turns off for one second, then back on. The test
routine starts at the top left panel moving from top to bottom for all 14 LEDs. Then the eight pushbutton LEDs are
tested in the same manner. This test checks for hardware failures that lead to more than one LED being turned off
from a single logic point. This stage can be interrupted at any time.
4. Additionally, stages 2 and 3 are repeated twice for the five device status LEDs and nine event cause LEDs, one time
with green color on and the other with red color on.
When testing is in progress, the LEDs are controlled by the test sequence, rather than the protection, control, and
monitoring features. However, the LED control mechanism accepts all the changes to LED states generated by the relay
and stores the actual LED states (on or off) in memory. When the test completes, the LEDs reflect the actual state resulting
from relay response during testing. The reset pushbutton does not clear any targets when the LED Test is in progress.
A dedicated FlexLogic operand, LED TEST IN PROGRESS, is set for the duration of the test. When the test sequence is initiated,
the LED TEST INITIATED event is stored in the event recorder.
The entire test procedure is user-controlled. In particular, stage 1 can last as long as necessary, and stages 2 and 3 can be
interrupted. The test responds to the position and rising edges of the control input defined by the LED TEST CONTROL
setting. The control pulses must last at least 250 ms to take effect. The following diagram explains how the test is
executed.
5

Figure 5-47: LED test sequence
READY TO TEST
Reset the
LED TEST IN PROGRESS
rising edge of the
operand
control input
Start the software image of Restore the LED states

the LEDs from the software image
Set the
LED TEST IN PROGRESS
operand
control input is on
STAGE 1 time-out
(all LEDs on) (1 minute)
dropping edge of the

control input
rising edge of the

Wait 1 second
control input
STAGE 2 rising edge of the

(one LED on at a time) control input
rising edge of the
5
Wait 1 second
control input
rising edge
STAGE 3
of the control
(one LED off at a time) input
842011A1.CDR
Application example 1
Assume one needs to check if any of the LEDs is “burned” through user-programmable pushbutton 1. Apply the following
settings.
Configure user-programmable pushbutton 1 by making the following entries in the SETTINGS  PRODUCT SETUP  USER-
PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 menu. (The option does not display when not purchased.)
PUSHBTN 1 DROP-OUT TIME: “0.10 s”
Configure the LED test to recognize user-programmable pushbutton 1 by making the following entries in the SETTINGS 
PRODUCT SETUP  USER-PROGRAMMABLE LEDS  LED TEST menu:
LED TEST FUNCTION: “Enabled”
LED TEST CONTROL: “PUSHBUTTON 1 ON”
The test is initiated when the user-programmable pushbutton 1 is pressed. Keep the pushbutton pressed for as long as the
LEDs are being visually inspected. When finished, release the pushbutton. The relay then automatically starts stage 2. At
this point, test can be cancelled by pressing the pushbutton.
Assume one needs to check if any LEDs are “burned” as well as exercise one LED at a time to check for other failures. This
is to be performed via user-programmable pushbutton 1.
After applying the settings in application example 1, hold down the pushbutton as long as necessary to test all LEDs. When
finished, release the pushbutton so that the relay then automatically starts stage 2. When stage 2 is completed, stage 3
starts automatically. The test can be cancelled at any time by pressing the pushbutton.

5.3.11.4 Trip and alarm LEDs

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  TRIP & ALARMS LEDS
 TRIP & ALARM LEDS TRIP LED INPUT: Range: FlexLogic operand
  Off
ALARM LED INPUT: Range: FlexLogic operand

 Off
The trip and alarm LEDs are in the first LED column (enhanced and graphical front panels) and on LED panel 1 (basic front
panel). Each LED can be programmed to turn on when the selected FlexLogic operand is in the logic 1 state.
5.3.11.5 User-programmable LED 1(48)

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  USER-PROGRAMMABLE LED 1(48)
 USER-PROGRAMMABLE LED 1 OPERAND: Range: FlexLogic operand
 LED 1  Off
LED 1 TYPE: Range: Self-Reset, Latched

 Self-Reset
For the enhanced and basic front panels, there are 48 amber LEDs across the relay LED panels. Each of these indicators
can be programmed to illuminate when the selected FlexLogic operand is in the logic 1 state.
For the basic front panel, the LEDs are located as follows:
• LED Panel 2 — User-programmable LEDs 1 through 24
• LED Panel 3 — User programmable LEDs 25 through 48
5 For the enhanced front panel, the LEDs are located as follows:
• LED column 2 — User-programmable LEDs 1 through 12
See the LED Indicators section in chapter 4 for information on the location of these indexed LEDs.
The user-programmable LED settings select the FlexLogic operands that control the LEDs. If the LED 1 TYPE setting is “Self-
Reset” (the default setting), the LED illumination tracks the state of the selected LED operand. If the LED 1 TYPE setting is
“Latched,” the LED, once lit, remains so until reset by the front panel RESET button, from a remote device via a
communications channel, or from any programmed operand, even if the LED operand state de-asserts.
Table 5-14: Recommended settings for user-programmable LEDs
Setting Parameter Setting Parameter
LED 1 operand SETTING GROUP ACT 1 LED 13 operand Off
LED 7 operand Off LED 19 operand Off

5.3.11.6 Event cause LED 1(9)

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE LEDS  EVENT CAUSE LED 1(9)
 EVENT CAUSE LED 1 LED 1 OPERAND: Range: FlexLogic operand
  LED PICKUP
LED 1 COLOR: Range: Red, Green, Orange

 Green
LED 1 TYPE: Range: Self-Reset, Latched

 Self-Reset
For the graphical front panel, the event cause LED settings select the FlexLogic operands that control the LEDs.
LED 1 TYPE — If set to "Self-Reset," the LED illumination tracks the state of the selected LED operand. If set to "Latched," the
LED, once lit, remains so even the LED operand state already de-asserts, until reset by the front panel RESET button, from a
remote device via a communications channel, or from any programmed operand.
The table outlines default input operand and output operands for each event cause LED.
Table 5-15: Default input and output operand for event cause LEDs
LED Default input operand Output operand Default color
Event Cause LED 1 LED PICKUP EVENT CAUSE LED 1 Green
Event Cause LED 2 LED VOLTAGE EVENT CAUSE LED 2 Orange
Event Cause LED 3 LED CURRENT EVENT CAUSE LED 3 Orange
Event Cause LED 4 LED FREQUENCY EVENT CAUSE LED 4 Orange
Event Cause LED 5 LED OTHER EVENT CAUSE LED 5 Orange
Event Cause LED 6
Event Cause LED 7
LED PHASE A
LED PHASE B
EVENT CAUSE LED 6
EVENT CAUSE LED 7
Orange
Orange
5
Event Cause LED 8 LED PHASE C EVENT CAUSE LED 8 Orange
Event Cause LED 9 LED NEUTRAL/GROUND EVENT CAUSE LED 9 Orange
5.3.12 User-programmable self-tests

SETTINGS  PRODUCT SETUP  USER-PROGRAMMALBE SELF TESTS
 USER-PROGRAMMABLE DIRECT RING BREAK Range: Disabled, Enabled. Valid for units equipped
 SELF TESTS  FUNCTION: Enabled with Direct Input/Output module.
DIRECT DEVICE OFF Range: Disabled, Enabled. Valid for units equipped
 FUNCTION: Enabled with Direct Input/Output module.
RxGOOSE OFF Range: Disabled, Enabled

 FUNCTION: Enabled
FIRST ETHERNET FAIL Range: Disabled, Enabled

SEC. ETHERNET FAIL Range: Disabled, Enabled

THIRD ETHERNET FAIL Range: Disabled, Enabled

SFP MODULE FAIL Range: Disabled, Enabled

BATTERY FAIL Range: Disabled, Enabled

SNTP FAIL Range: Disabled, Enabled


IRIG-B FAIL Range: Disabled, Enabled

PTP FAIL Range: Disabled, Enabled

 FUNCTION: Enabled
All major self-test alarms are reported automatically with their corresponding FlexLogic operands, events, and targets.
This settings menu allows enabling and disabling of most minor self-test alarms.
When in the Disabled mode, minor alarms do not assert a FlexLogic operand, write to the event recorder, or display target
messages. Moreover, they do not trigger the ANY MINOR ALARM or ANY SELF-TEST messages. When in Enabled mode,
minor alarms continue to function along with other major and minor alarms. See the Relay Self-tests section in chapter 7
for information on major and minor self-test alarms.
When using the graphical front panel and setting annunciator alarms, the function needs to be enabled here too, else the
alarm is not triggered.
5.3.13 Control pushbuttons

SETTINGS  PRODUCT SETUP  CONTROL PUSHBUTTONS  CONTROL PUSHBUTTON 1(7)
 CONTROL CONTROL PUSHBUTTN 1 ID Range: up to 20 alphanumeric characters
 PUSHBUTTON 1  CTRL PB 1
CONTROL PUSHBUTTON 1 Range: Disabled, Enabled

CONTROL PUSHBUTTON 1 Range: Disabled, Enabled

5 This feature is supported with enhanced and basic front panels.
There are three standard control pushbuttons, labelled USER 1, USER 2, and USER 3, on the basic and enhanced front
panels. These are user-programmable and can be used for various applications such as performing an LED test, switching
setting groups, and invoking and scrolling though user-programmable displays.
The location of the control pushbuttons are shown in the following figures.
Figure 5-48: Control pushbuttons (enhanced front panel)
Control pushbuttons
842813A1.CDR
An additional four control pushbuttons are included on the basic front panel when the B90 is ordered with the 12 user-
programmable pushbutton option.

Figure 5-49: Control pushbuttons (basic front panel)
STATUS EVENT CAUSE

IN SERVICE VOLTAGE
TROUBLE CURRENT RESET
TEST MODE FREQUENCY
TRIP OTHER USER 1 THREE
ALARM PHASE A STANDARD
PICKUP PHASE B USER 2
PHASE C
CONTROL
NEUTRAL/GROUND USER 3 PUSHBUTTONS
USER 4
USER 5 FOUR EXTRA

OPTIONAL
USER 6
CONTROL
USER 7 PUSHBUTTONS
842733A2.CDR
Control pushbuttons are not typically used for critical operations and are not protected by the control password. However,
by supervising their output operands, the user can dynamically enable or disable control pushbuttons for security reasons.
Each control pushbutton asserts its own FlexLogic operand. Each operand need to be configured appropriately to perform
the required function. Each operand remains asserted as long as the pushbutton is pressed and resets when the
pushbutton is released. A dropout delay of 100 ms is incorporated to ensure fast pushbutton manipulation is recognized
by various features that can use control pushbuttons as inputs.
An event is logged in the event record (as per user setting) when a control pushbutton is pressed. No event is logged when
the pushbutton is released. The front panel keys (including control keys) cannot be operated simultaneously—a given key
must be released before the next one can be pressed. 5
Figure 5-50: Control pushbutton logic
SETTING
CONTROL PUSHBUTTON
{
1 FUNCTION:
Enabled=1
SETTINGS
SYSTEM SETUP/
BREAKERS/BREAKER 1/
BREAKER 1 PUSHBUTTON
CONTROL:
When applicable
AND RUN
Enabled=1
OFF TIMER
SYSTEM SETUP/ FLEXLOGIC OPERAND
BREAKERS/BREAKER 2/ ON 0 CONTROL PUSHBTN 1 ON
BREAKER 2 PUSHBUTTON 100 msec
CONTROL:
842010A2.CDR
Enabled=1
5.3.14 User-programmable pushbuttons

SETTINGS  PRODUCT SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1(16)
 USER PUSHBUTTON 1 PUSHBUTTON 1 Range: Self-Reset, Latched, Disabled
  FUNCTION: Disabled
PUSHBTN 1 ID TEXT: Range: up to 20 alphanumeric characters

 USER PB 1
PUSHBTN 1 ON TEXT: Range: up to 20 alphanumeric characters


PUSHBTN 1 OFF TEXT: Range: up to 20 alphanumeric characters


PUSHBTN 1 HOLD: Range: 0.0 to 10.0 s in steps of 0.1

 0.0 s
PUSHBTN 1 SET: Range: FlexLogic operand

 Off
PUSHBTN 1 RESET: Range: FlexLogic operand

 Off
PUSHBTN 1 AUTORST: Range: Disabled, Enabled

 Disabled
PUSHBTN 1 AUTORST Range: 0.2 to 600.0 s in steps of 0.1

 DELAY: 1.0 s
PUSHBTN 1 REMOTE: Range: FlexLogic operand

 Off
PUSHBTN 1 LOCAL: Range: FlexLogic operand

 Off
PUSHBTN 1 DROP-OUT Range: 0 to 60.00 s in steps of 0.05

 TIME: 0.00 s
PUSHBTN 1 LED CTL: Range: FlexLogic operand

 Off
PUSHBTN 1 MESSAGE: Range: Disabled, Normal, High Priority

 Disabled
PUSHBUTTON 1 Range: Disabled, Enabled

5
The B90 is provided with this optional feature, specified as an option at the time of ordering. Using the order
code for your device, see the order codes in chapter 2 for details.
User-programmable pushbuttons provide an easy and error-free method of entering digital state (on, off) information. The
number depends on the front panel ordered.
• Enhanced horizontal front panel — 16 user-programmable pushbuttons
• Enhanced vertical front panel — 6 user-programmable pushbuttons
• Basic horizontal front panel — 12 user-programmable pushbuttons
• Graphical front panel — 16 user-programmable pushbuttons (eight physical pushbuttons, eight graphical interface
pushbuttons)
User-programmable pushbuttons require a front panel with that option. If the front panel was ordered separately,
update the EnerVista software under Maintenance > Change Front Panel.
The digital state can be entered locally (by directly pressing the front panel pushbutton or optional graphical front panel
interface) or remotely (via FlexLogic operands) into FlexLogic equations, protection elements, and control elements. Typical
applications include breaker control, autorecloser blocking, and setting groups changes. For example, set pushbuttons 1 to
5 to select settings groups 1 to 5, or set pushbutton 1 to clear event records. The user-programmable pushbuttons are
under the control level of password protection.
Example
To clear event records using pushbutton 1, set Settings > Product Setup > Clear Relay Records > Clear Event Records to
FlexLogic operand PUSHBUTTON 1 ON. Then program the pushbutton by setting Settings > Product Setup > User-
Programmable Pushbuttons > Pushbutton 1 Function to "Self-reset." For a graphical front panel, to use a side
pushbutton 9 to 16 to clear the event records, it also needs to be programmed in a single-line diagram.
The figures show user-configurable pushbuttons for the front panels.

Figure 5-51: User-programmable pushbuttons (enhanced front panel)

USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER USER
LABEL 1 LABEL 2 LABEL 3 LABEL 4 LABEL 5 LABEL 6 LABEL 7 LABEL 8 LABEL 9 LABEL 10 LABEL 11 LABEL 12 LABEL 13 LABEL 14 LABEL 15 LABEL 16
842814A1.CDR
Figure 5-52: User-programmable pushbuttons (basic front panel)
1 3 5 7 9 11
USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL
2 4 6 8 10 12
USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL USER LABEL
842779A1.cdr
Figure 5-53: User-programmable pushbuttons (graphical front panel)

Program any buttons for pushbuttons 9 to 16 Pushbuttons 1 to 8
5
1 5
2 6
3 7
4 8
RESET ESC
ENTER
Multilin N60 Network Stability and Synchrophasor Measurement System
859761A1.CDR
Front panel pushbuttons and LEDs can be custom labelled as outlined in the Front Panel Labelling section in the previous
chapter.
Each pushbutton asserts its own “On” and “Off” FlexLogic operands (for example, PUSHBUTTON 1 ON and PUSHBUTTON 1 OFF).
These operands are available for each pushbutton and are used to program specific actions. If any pushbutton is active,
the ANY PB ON operand is asserted.
Each pushbutton has an associated LED indicator. By default, this indicator displays the present status of the
corresponding pushbutton (on or off). However, each LED indicator can be assigned to any FlexLogic operand through the
PUSHBTN 1 LED CTL setting.
The activation and deactivation of user-programmable pushbuttons depends on whether latched or self-reset mode is
programmed.
• Latched mode — In latched mode, a pushbutton can be set (activated) by asserting the operand assigned to the
PUSHBTN 1 SET setting, by directly pressing the associated front panel pushbutton, or with the graphical front panel

interface. The state of each pushbutton is stored in non-volatile memory and maintained through a loss of control
power.
The pushbutton is reset (deactivated) in latched mode by asserting the operand assigned to the PUSHBTN 1 RESET
setting, by directly pressing the active front panel pushbutton, or with the graphical front panel interface.
It can also be programmed to reset automatically through the PUSHBTN 1 AUTORST and PUSHBTN 1 AUTORST DELAY
settings. These settings enable the autoreset timer and specify the associated time delay. The autoreset timer can be
used in select-before-operate (SBO) breaker control applications, where the command type (close/open) or breaker
location (feeder number) must be selected prior to command execution. The selection must reset automatically if
control is not executed within a specified time period.
• Self-reset mode — In self-reset mode, a user-programmable pushbutton can be set (activated) by asserting the
operand assigned to the PUSHBTN 1 SET setting, by pressing the front panel pushbutton, or by the graphical front panel
interface. A pushbutton remains active for the time it is pressed physically or pressed in the graphical front panel
interface, plus the dropout time specified in the PUSHBTN 1 DROP-OUT TIME setting. If the pushbutton is activated via
FlexLogic, the pulse duration is specified by the PUSHBTN 1 DROP-OUT TIME only. The time the operand assigned to the
PUSHBTN 1 SET setting remains On has no effect on the pulse duration.
The pulse duration of the remote set or local front panel pushbutton must be at least 50 ms to operate the
pushbutton. This allows the user-programmable pushbuttons to properly operate during power cycling events and
various system disturbances that can cause transient assertion of the operating signals.
The local and remote operation of each user-programmable pushbutton can be inhibited through the PUSHBTN 1 LOCAL
and PUSHBTN 1 REMOTE settings. If local inhibit is applied, the pushbutton ignores set and reset commands executed
through the front panel pushbuttons. If remote inhibit is applied, the pushbutton ignores set and reset commands
executed through FlexLogic operands.
5 The inhibit functions are not applied to the autoreset feature. The inhibit function can be used in SBO control operations to
prevent user-programmable pushbutton activation and ensuring “one-at-a-time” select operation.
The inhibit functions can also be used to prevent pushbutton activation from the accidental pressing of the front panel
pushbuttons. The separate inhibit of the local and remote operation simplifies the implementation of local/remote control
supervision.
Pushbutton states can be logged by the event recorder. User-defined messages can also be associated with each
pushbutton and displayed on basic and enhanced front panels when the user-programmable pushbutton is activated, and
when in the latched mode when the user-programmable pushbutton is deactivated. With the graphical front panel
interface, instead of messages, the status of user-programmable pushbuttons can display on a single-line diagram and
can also display in annunciator page windows and in actual values page cells.
For the graphical front panel, the pushbuttons 1 to 8 are linked to the eight physical pushbuttons, and pushbuttons 9 to 16
are mapped to the graphical interface pushbuttons. To set the buttons for pushbuttons 9 to 16, access Settings > Product
Setup > Graphical Panel > Single Line Diagram Editor, click the PB symbol in the toolbox, then configure pushbuttons 9 to
16.
PUSHBUTTON 1 FUNCTION — This setting selects the mode of the pushbutton (Self-Reset, Latched, Disabled). If set to
“Disabled,” the pushbutton is not active and the corresponding FlexLogic operands (both “On” and “Off”) are de-asserted. If
set to "Latched," the pushbutton remains on until reset.
PUSHBTN 1 ID TEXT — This setting specifies the top 20-character line of the user-programmable pushbutton message and is
intended to provide ID information of the pushbutton. For example, the text displays in the Event Record. See the User-
definable Displays section in this chapter for instructions on how to enter alphanumeric characters from the keypad. On a
graphical front panel, this setting instead controls the label of the user-programmable pushbutton component on single-
line diagrams.
PUSHBTN 1 ON TEXT — This setting specifies the bottom 20-character line of the user-programmable pushbutton message
and is displayed when the pushbutton is in the “on” position. See the User-definable Displays section for instructions on
entering alphanumeric characters from the keypad. On a graphical front panel, this setting instead controls the on status
text of the user-programmable pushbutton component on single-line diagrams. This setting is not applied to the physical
pushbuttons on the graphical front panel.

PUSHBTN 1 OFF TEXT — This setting specifies the bottom 20-character line of the user-programmable pushbutton message
and displays when the pushbutton is deactivated and the PUSHBUTTON 1 FUNCTION is “Latched.” A message does not
display when the PUSHBUTTON 1 FUNCTION is “Self-reset” as the pushbutton operand status is implied to be “Off” upon its
release. The length of the “Off” message is configured with the PRODUCT SETUP  DISPLAY PROPERTIES  FLASH MESSAGE
TIME setting. On a graphical front panel, this setting instead controls the off status text of the user-programmable
pushbutton component on single-line diagrams. This setting is not applied to the physical pushbuttons on the graphical
front panel.
PUSHBTN 1 HOLD — This setting specifies the time required for a front panel pushbutton to be pressed before it is deemed
active. This timer is reset upon release of the pushbutton. Note that user-programmable pushbutton operation requires the
front panel pushbutton to be pressed a minimum of 50 ms. This minimum time is required prior to activating the user-
programmable pushbutton hold timer.
PUSHBTN 1 SET — This setting assigns the FlexLogic operand serving to activate the user-programmable pushbutton
element. The duration of the incoming set signal must be at least 50 ms.
PUSHBTN 1 RESET — This setting assigns the FlexLogic operand serving to deactivate the user-programmable pushbutton
element. This setting is applicable only if the user-programmable pushbutton is in "Latched" mode.
PUSHBTN 1 AUTORST — This setting enables the user-programmable pushbutton autoreset feature. This setting is applicable
only if the pushbutton is in “Latched” mode.
PUSHBTN 1 AUTORST DELAY — This setting specifies the time delay for automatic reset of the pushbutton when in "Latched"
mode.
PUSHBTN 1 REMOTE — This setting assigns the FlexLogic operand serving to inhibit user-programmable pushbutton
operation from the operand assigned to the PUSHBTN 1 SET or PUSHBTN 1 RESET settings.
PUSHBTN 1 LOCAL — This setting assigns the FlexLogic operand serving to inhibit user-programmable pushbutton operation
from the front panel pushbuttons. This inhibit functionality is not applicable to pushbutton autoreset.
PUSHBTN 1 DROP-OUT TIME — This setting applies only to “Self-Reset” mode and specifies the duration of the user- 5
programmable pushbutton active status after the front panel pushbutton or graphical front panel interface pushbutton
has been released. When activated remotely, this setting specifies the entire activation time of the pushbutton; the length
of time the operand selected by PUSHBTN 1 SET remains on has no effect on the pulse duration.
PUSHBTN 1 LED CTL — This setting assigns the FlexLogic operand serving to drive the front panel pushbutton LED. If this
setting is “Off,” then LED operation is directly linked to the PUSHBUTTON 1 ON operand. This setting is not applied to
Pushbuttons 9 to 16 on the graphical front panel, where the label background shows the orange glow color for the "on"
state.
PUSHBTN 1 MESSAGE — This setting controls the behavior of the user-programmable pushbutton on message that is
programmed in the PUSHBTN 1 ID and PUSHBTN 1 ON TEXT settings, and the behavior of the user-programmable pushbutton
off message that is programmed in the PUSHBTN 1 ID and PUSHBTN 1 OFF TEXT settings. This settings has no effect on the
When set to "Disabled", user-programmable pushbutton messages do not display. Otherwise the on message displays
when the user-programmable pushbutton becomes activated, and if in the "Latched" mode the off message displays when
the user-programmable pushbutton becomes deactivated.
When set to "Normal", the duration the message displays is as specified by the FLASH MESSAGE TIME setting.
When set to "High Priority", the duration of the off message is as specified by the FLASH MESSAGE TIME setting, but the on
message is displayed as long as the user-programmable pushbutton is activated. While activated, target and other
messages are suppressed. To allow front panel keypad operation, when a keypad button is pressed the message is
supressed for 10 seconds.
PUSHBUTTON 1 EVENTS — If this setting is enabled, each user-programmable pushbutton state change is logged as an
event into the event recorder.
The figures show the user-programmable pushbutton logic.

Figure 5-54: User-programmable pushbutton logic (Sheet 1 of 2)

SETTING
PUSHBUTTON 1 FUNCTION
= Enabled
= Latched LATCHED To user-programmable
= Self-Reset pushbuttons logic
sheet 2
OR From front panel
SETTING SETTING
PUSHBTN 1 LOCAL PUSHBTN 1 HOLD
Off = 0 TPKP
From front panel AND
0
AND
OR TIMER
From graphical front panel
50 ms
SETTING 0 OR
PUSHBTN 1 SET
Off = 0 TIMER
50 ms Non-volatile latch
SETTING AND S
AND
0
PUSHBTN 1 REMOTE Latch
Off = 0 R
TIMER
SETTING 200 ms
PUSHBUTTON 1 OFF
0
SETTING
PUSHBTN 1 RESET AND
Off = 0
OR To user-programmable
SETTING OR PUSHBUTTON ON pushbuttons logic
SETTING sheet 2
PUSHBTN 1 AUTORST DELAY
PUSHBTN 1 AUTORST
TPKP
= Enabled
AND AND
= Disabled
5
0
TIMER
FLEXLOGIC OPERAND 200 ms OR
PUSHBUTTON 1 ON
0
SETTING
AND PUSHBTN 1 DROP-OUT TIME
0
OR
TRST
AND
842237A1.CDR

Figure 5-55: User-programmable pushbutton logic (Sheet 2 of 2)
OFF MESSAGE
ENGAGE MESSAGE
SETTING
LATCHED FLASH MESSAGE TIME
SETTINGS
0 PUSHBTN ID TEXT
AND
OR TRST = XXXXXXXXXX
PUSHBTN OFF TEXT
= XXXXXXXXXX
Instantaneous
From user-programmable reset * Enhanced and standard front panels
pushbuttons logic sheet 1
FLEXLOGIC OPERAND
LATCHED/SELF-RESET
AND PUSHBUTTON 1 OFF
FLEXLOGIC OPERAND
PUSHBUTTON ON PUSHBUTTON 1 ON
ON MESSAGE
SETTING ENGAGE MESSAGE
PUSHBTN 1 MESSAGE
AND
= Disabled
= High Priority SETTINGS
= Normal PUSHBTN ID TEXT
= XXXXXXXXXX
OR
PUSHBTN ON TEXT
SETTING
= XXXXXXXXXX
FLASH MESSAGE TIME
0 Enhanced and standard front panels
AND
TRST The message is temporarily removed if
5
any keypad button is pressed. Ten
seconds of keypad inactivity restores
Instantaneous
Instantaneous reset is executed if any reset * the message.
front panel button is pressed or any new
target or message becomes active.
PUSHBUTTON 1 LED LOGIC

1. If pushbutton 1 LED control is set to off.
Pushbutton 1
FLEXLOGIC OPERAND FLEXLOGIC OPERAND LED
PUSHBUTTON 1 ON PUSHBUTTON 1 ON
PUSHBUTTON 2 ON
FLEXLOGIC OPERAND
PUSHBUTTON 3 ON 2. If pushbutton 1 LED control is not set to off.
OR ANY PB ON
SETTING Pushbutton 1
LED
PUSHBTN 1 LED CTL
PUSHBUTTON 16 ON = any FlexLogic operand
The enhanced front panel has 16 operands;
the standard front panel has 12
842239A1.CDR
5.3.15 Flex state parameters

SETTINGS  PRODUCT SETUP  FLEX STATE PARAMETERS
 FLEX STATE PARAMETER 1: Range: FlexLogic operand
 PARAMETERS  Off

PARAMETER 256: Range: FlexLogic operand
 Off
This feature provides a mechanism where any of 256 selected FlexLogic operand states can be used for efficient
monitoring. The feature allows user-customized access to the FlexLogic operand states in the relay. The state bits are
packed so that 16 states are readable in a single Modbus register. The state bits can be configured so that all states of
interest are available in a minimum number of Modbus registers.
The state bits can be read out in the “Flex States” register array beginning at Modbus address 0900h. Sixteen states are
packed into each register, with the lowest-numbered state in the lowest-order bit. Sixteen registers accommodate the 256
state bits.

5.3.16 User-definable displays
5.3.16.1 Menu
SETTINGS  PRODUCT SETUP  USER-DEFINABLE DISPLAYS
 USER-DEFINABLE INVOKE AND SCROLL: Range: FlexLogic operand
 DISPLAYS  Off
 USER DISPLAY 1 See below

 

 USER DISPLAY 16
 
This feature is supported with enhanced and basic front panels.

This menu provides a mechanism for manually creating up to 16 user-defined information displays in a convenient
viewing sequence in the USER DISPLAY menu (between the TARGETS and ACTUAL VALUES top-level menus). The sub-menus
facilitate text entry and Modbus register data pointer options for defining the user display content.
This feature is not supported with the optional graphical front panel.
Once programmed, the user-definable displays can be viewed in two ways.
• Keypad — Use the MENU key to select the USER DISPLAY menu item to access the first user-definable display (note that
only the programmed screens are displayed). The screens can be scrolled using the up and down arrow keys. The
display disappears after the default message time-out period specified by the PRODUCT SETUP  DISPLAY PROPERTIES
 DEFAULT MESSAGE TIMEOUT setting.
5 • User-programmable control input — The user-definable displays also respond to the INVOKE AND SCROLL setting. Any
FlexLogic operand (in particular, the user-programmable pushbutton operands), can be used to navigate the
programmed displays.
On the rising edge of the configured operand (such as when the pushbutton is pressed), the displays are invoked by
showing the last user-definable display shown during the previous activity. From this moment onward, the operand
acts exactly as the down key and allows scrolling through the configured displays. The last display wraps up to the
first one. The INVOKE AND SCROLL input and the down arrow key operate concurrently.
When the default timer expires (set by the DEFAULT MESSAGE TIMEOUT setting), the relay starts to cycle through the user
displays. The next activity of the INVOKE AND SCROLL input stops the cycling at the currently displayed user display, not
at the first user-defined display. The INVOKE AND SCROLL pulses must last for at least 250 ms to take effect.
5.3.16.2 User display 1(16)

SETTINGS  PRODUCT SETUP  USER-DEFINABLE DISPLAYS  USER DISPLAY 1(16)
 USER DISPLAY 1 DISP 1 TOP LINE: Range: up to 20 alphanumeric characters
 
DISP 1 BOTTOM LINE: Range: up to 20 alphanumeric characters

DISP 1 ITEM 1: Range: 0 to 65535 in steps of 1
 0

DISP 1 ITEM 5: Range: 0 to 65535 in steps of 1
 0
Any existing system display can be automatically copied into an available user display by selecting the existing display and
pressing the ENTER key. The display then prompts with ADD TO USER DISPLAY LIST? After selecting “Yes,” a message
indicates that the selected display has been added to the user display list. When this type of entry occurs, the sub-menus
are automatically configured with the proper content—this content can be edited subsequently.

This menu is used to enter user-defined text and user-selected Modbus-registered data fields into the particular user
display. Each user display consists of two 20-character lines (top and bottom). The tilde (~) character is used to mark the
start of a data field – the length of the data field needs to be accounted for. Up to five separate data fields can be entered
in a user display – the nth tilde (~) refers to the nth item.
A user display can be entered from the front panel keypad or the EnerVista interface (preferred for convenience). The
following procedure shows how to enter text characters in the top and bottom lines from the front panel keypad:
1. Select the line to be edited.
2. Press the decimal key to enter text edit mode.
3. Use either VALUE key to scroll through the characters. A space is selected like a character.
4. Press the decimal key to advance the cursor to the next position.
5. Repeat step 3 and continue entering characters until the desired text is displayed.
6. The HELP key can be pressed at any time for context sensitive help information.
7. Press the ENTER key to store the new settings.
To enter a numerical value for any of the five items (the decimal form of the selected Modbus address) from the front panel
keypad, use the number keypad. Use the value of “0” for any items not being used. Use the HELP key at any selected
system display (setting, actual value, or command) which has a Modbus address, to view the hexadecimal form of the
Modbus address, then manually convert it to decimal form before entering it (EnerVista usage conveniently facilitates this
conversion).
Use the MENU key to go to the user displays menu to view the user-defined content. The current user displays show in
sequence, changing every four seconds. While viewing a user display, press the ENTER key and then select the ‘Yes” option
to remove the display from the user display list. Use the MENU key again to exit the user displays menu.
An example of user display setup and result is shown as follows.
 USER DISPLAY 1
 DISP 1 TOP LINE: Shows user-defined text with first tilde marker 5
 Current X ~ A
DISP 1 BOTTOM LINE: Shows user-defined text with second tilde marker
 Current Y ~ A
DISP 1 ITEM 1: Shows decimal form of user-selected Modbus register

 6016 address, corresponding to first tilde marker
DISP 1 ITEM 2: Shows decimal form of user-selected Modbus register

 6357 address, corresponding to second tilde marker
DISP 1 ITEM 3: This item is not being used. There is no corresponding

 0 tilde marker in top or bottom lines.

 0 tilde marker in top or bottom lines.

 0 tilde marker in top or bottom lines.
USER DISPLAYS Current X 0.850 Shows the resultant display content

 Current Y 0.327 A
If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the bottom
line only. The units are only displayed on both lines if the units specified both the top and bottom line items are different.

5.3.17 Direct inputs and outputs
5.3.17.1 Menu
SETTINGS  PRODUCT SETUP  DIRECT I/O
 DIRECT I/O DIRECT OUTPUTS Range: 1 to 16 in steps of 1
  DEVICE ID: 1
DIRECT I/O CH1 RING Range: Yes, No

 CONFIGURATION: Yes
DIRECT I/O CH2 RING Range: Yes, No

 CONFIGURATION: Yes
DIRECT I/O DATA Range: 64 kbps, 128 kbps, 213 kbps

 RATE: 64 kbps
DIRECT I/O CHANNEL Range: Disabled, Enabled

 CROSSOVER: Disabled
 CRC ALARM CH1 See page 5-129

 
 CRC ALARM CH2

 
 UNRETURNED See page 5-130

  MESSAGES ALARM CH1
 UNRETURNED

5  MESSAGES ALARM CH2
This option is available when an Inter-Relay Communications card is specified at the time of ordering (see the
Order Code tables). With the option, direct inputs/outputs display by default. When you enable the
teleprotection feature, direct I/O is not visible.
Direct inputs and outputs exchange status information (inputs and outputs) between UR-series relays connected directly
via type 7 digital communications cards. The mechanism is very similar to IEC 61850 GOOSE, except that communications
takes place over a non-switchable isolated network and is optimized for speed. On type 7 cards that support two channels,
direct output messages are sent from both channels simultaneously. This effectively sends direct output messages both
ways around a ring configuration. On type 7 cards that support one channel, direct output messages are sent only in one
direction. Messages are resent (forwarded) when it is determined that the message did not originate at the receiver.
Direct Inputs and Outputs are initiated automatically and start running once at least one Direct Output in the given UR is
set to anything but Off.
Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive. As such, they cannot be used
simultaneously. Once teleprotection inputs and outputs are enabled, direct inputs and outputs are disabled, and
vice versa.
B90 supports 96 Direct I/Os at 64 or 128 kbps rate and 256 Direct I/Os at 213 kbps rate. With 64 or 128 kbps rate, the B90
can exchange Direct I/Os with other URs, while at 213 kbps B90s can exchange between each other's only. Functionality at
213 kbps is possible only with firmware 7.4 or higher and with CPU FPGA revision 2.02 or higher. The CPU FPGA version can
be confirmed in the ACTUAL VALUES > PRODUCT INFO > FIRMWARE REVISIONS > FPGA PROGRAM REVISION menu. CPU FPGA can
be upgraded in the field; see the upgrade procedures on the B90 Support Documents page of the GE Multilin web site. In
version 7.42 and later, when connected by serial cable, use Maintenance > Update FPGA Firmware.
Direct output message timing is similar to GOOSE message timing. Integrity messages (with no state changes) are sent at
least every 1000 ms. Messages with state changes are sent within the main pass scanning the inputs and asserting the
outputs unless the communication channel bandwidth has been exceeded. Two self-tests are performed and signaled by
the following FlexLogic operands:

• DIRECT RING BREAK (direct input/output ring break). This FlexLogic operand indicates that direct output messages sent
from a UR-series relay are not being received back by the relay.
• DIRECT DEVICE 1 OFF to DIRECT DEVICE 16 OFF (direct device offline). These FlexLogic operands indicate that direct output
messages from at least one direct device are not being received.
Direct input and output settings are similar to remote input and output settings. The equivalent of the remote device name
strings for direct inputs and outputs is the DIRECT OUTPUT DEVICE ID setting, which identifies the relay in all direct output
messages. All UR-series IEDs in a ring need to have unique numbers assigned. The IED ID is used to identify the sender of
the direct input and output message.
If the direct input and output scheme is configured to operate in a ring (DIRECT I/O CH1 RING CONFIGURATION or DIRECT I/O
CH2 RING CONFIGURATION is “Yes”), all direct output messages are received back. If not, the direct input/output ring break
self-test is triggered. The self-test error is signaled by the DIRECT RING BREAK FlexLogic operand.
Select the DIRECT I/O DATA RATE to match the data capabilities of the communications channel. All IEDs communicating
over direct inputs and outputs must be set to the same data rate. UR-series IEDs equipped with dual-channel
communications cards apply the same data rate to both channels. Delivery time for direct input and output messages is
approximately 0.2 of a power system cycle at 128 or 213 kbps and 0.4 of a power system cycle at 64 kbps, per each
"bridge."
For B90 applications, the DIRECT I/O DATA RATE should be set to 128 or 213 kbps.
Table 5-16: Direct input and output data rates
Module Supported data rates
2A, 2B 64 kbps
2E, 2F 64 kbps
2G, 2H 128 kbps
2I, 2J 64 kbps, 128 kbps 5
72, 73 64 kbps, 128 kbps, 213 kbps
74, 75 64 kbps
76, 77 64 kbps
7A, 7B, 7C, 7D 64 kbps, 128 kbps, 213 kbps
7E, 7F, 7G 64 kbps
7H, 7I, 7J, 7K 64 kbps, 128 kbps, 213 kbps
7L, 7M, 7N, 7P, 7Q 64 kbps
7R, 7S 64 kbps
7T, 7W 64 kbps
The G.703 modules are fixed at 64 kbps. The DIRECT I/O DATA RATE setting is not applicable to these modules.
The DIRECT I/O CHANNEL CROSSOVER setting applies to a B90 with dual-channel communication cards and allows crossing
over messages from channel 1 to channel 2. This places all UR-series IEDs into one direct input and output network
regardless of the physical media of the two communication channels.
The following application examples illustrate the basic concepts for direct input and output configuration. See the Inputs
and Outputs section in this chapter for information on configuring FlexLogic operands (flags, bits) to be exchanged.
Example 1: Extending the input/output capabilities of a UR-series relay

Consider an application that requires additional quantities of contact inputs or output contacts or lines of programmable
logic that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED,
such as the C30, to satisfy the additional input and output and programmable logic requirements. The two IEDs are
connected via single-channel digital communication cards as shown in the figure.

Figure 5-56: Input and output extension via direct inputs and outputs
TX1
UR IED 1
RX1
TX1
UR IED 2
RX1
842711A1.CDR
In this application, apply the following settings. For UR-series IED 1:

DIRECT OUTPUT DEVICE ID: “1”
DIRECT I/O CH1 RING CONFIGURATION: “Yes”
DIRECT I/O DATA RATE: “128 kbps”
For UR-series IED 2:
DIRECT I/O DATA RATE: “128 kbps”
The message delivery time is about 0.2 of power cycle in both ways (at 128 kbps); that is, from device 1 to device 2, and
from device 2 to device 1. Different communications cards can be selected by the user for this back-to-back connection
(for example: fiber, G.703, or RS422).
Example 2: Interlocking busbar protection

5 A simple interlocking busbar protection scheme could be accomplished by sending a blocking signal from downstream
devices, say 2, 3, and 4, to the upstream device that monitors a single incomer of the busbar, as shown.
Figure 5-57: Sample interlocking busbar protection scheme
UR IED 1 BLOCK
UR IED 2 UR IED 3 UR IED 4
842712A1.CDR
For increased reliability, a dual-ring configuration (shown as follows) is recommended for this application.
Figure 5-58: Interlocking bus protection scheme via direct inputs/outputs
TX1 RX1
UR IED 1
RX2 TX2
RX1 TX2 RX2 TX1

UR IED 2 UR IED 4
TX1 RX2 TX2 RX1
TX2 RX2
UR IED 3
RX1 TX1
842716A1.CDR


Message delivery time is approximately 0.2 of power system cycle (at 128 kbps) times number of ‘bridges’ between the
origin and destination. Dual-ring configuration effectively reduces the maximum ‘communications distance’ by a factor of
two.
In this configuration the following delivery times are expected (at 128 kbps) if both rings are healthy:
IED 1 to IED 2: 0.2 of power system cycle
IED 2 to IED 3: 0.2 of power system cycle 5
If one ring is broken (say TX2-RX2) the delivery times are as follows:
A coordinating timer for this bus protection scheme could be selected to cover the worst case scenario (0.4 of a power
system cycle). Upon detecting a broken ring, the coordination time is adaptively increased to 0.6 of a power system cycle.
The complete application requires addressing a number of issues, such as failure of both the communications rings, failure
or out-of-service conditions of one of the relays, and so on. Self-monitoring flags of the direct inputs and outputs feature
primarily are used to address these concerns.
Example 3: Pilot-aided schemes

Consider the three-terminal line protection application shown.

Figure 5-59: Three-terminal line application
UR IED 1 UR IED 2
UR IED 3 842713A1.CDR
A permissive pilot-aided scheme can be implemented in a two-ring configuration, shown as follows (IEDs 1 and 2
constitute a first ring, while IEDs 2 and 3 constitute a second ring).
Figure 5-60: Single-channel open loop configuration
TX1 RX1 RX2

UR IED 1 UR IED 2
RX1 TX1 TX2
5 UR IED 3
RX1
TX1
842714A1.CDR

In this configuration the following delivery times are expected (at 128 kbps):
In this scheme, IEDs 1 and 3 do not communicate directly. IED 2 must be configured to forward the messages as explained
in the Inputs and Outputs section. Implement a blocking pilot-aided scheme with more security and, ideally, faster
message delivery time. This is accomplished using a dual-ring configuration as shown here.

Figure 5-61: Dual-channel closed loop (dual-ring) configuration
TX2 TX1 RX1 RX2

UR IED 1 UR IED 2
RX1 RX2 TX2 TX1
TX1 RX1
UR IED 3
RX2 TX2
842715A1.CDR

DIRECT I/O CH2 RING CONFIGURATION: “Yes” 5
In this configuration the following delivery times are expected (at 128 kbps) if both the rings are healthy:
The two communications configurations can be applied to both permissive and blocking schemes. Take speed, reliability,
and cost into account when selecting the required architecture.
5.3.17.2 CRC alarm CH1(2)

SETTINGS  PRODUCT SETUP  DIRECT I/O  CRC ALARM CH1(2)
 CRC ALARM CH1 CRC ALARM CH1 Range: Enabled, Disabled
CRC ALARM CH1 Range: 100 to 10000 in steps of 1

 MESSAGE COUNT: 600
CRC ALARM CH1 Range: 1 to 1000 in steps of 1

 THRESHOLD: 10
CRC ALARM CH1 Range: Enabled, Disabled

The B90 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is
available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The
monitoring function counts all incoming messages, including messages that failed the CRC check. A separate counter
adds up messages that failed the CRC check. When the failed CRC counter reaches the user-defined level specified by the
CRC ALARM CH1 THRESHOLD setting within the user-defined message count CRC ALARM 1 CH1 COUNT, the DIR IO CH1 CRC
ALARM FlexLogic operand is set.
When the total message counter reaches the user-defined maximum specified by the CRC ALARM CH1 MESSAGE COUNT
setting, both the counters reset and the monitoring process is restarted.

Configure the operand to drive an output contact, user-programmable LED, or selected communication-based output.
Latching and acknowledging conditions—if required—are programmed accordingly.
The CRC alarm function is available on a per-channel basis. The total number of direct input and output messages that
failed the CRC check is available as the ACTUAL VALUES  STATUS  DIRECT INPUTS  CRC FAIL COUNT CH1 actual value.
• Message count and length of the monitoring window — To monitor communications integrity, the relay sends 1
message per second (at 64 kbps) or 2 messages per second (at 128 kbps) or 3 messages per second (at 213 kbps) even
if there is no change in the direct outputs. For example, setting the CRC ALARM CH1 MESSAGE COUNT to “10000,”
corresponds a time window of about 160 minutes at 64 kbps and 80 minutes at 128 kbps. If the messages are sent
faster as a result of direct outputs activity, the monitoring time interval shortens. Take this into account when
determining the CRC ALARM CH1 MESSAGE COUNT setting. For example, if the requirement is a maximum monitoring
time interval of 10 minutes at 64 kbps, then the CRC ALARM CH1 MESSAGE COUNT is set to 10  60  1 = 600.
• Correlation of failed CRC and bit error rate (BER) — The CRC check can fail if one or more bits in a packet are
corrupted. Therefore, an exact correlation between the CRC fail rate and the BER is not possible. Under certain
assumptions an approximation can be made as follows. A direct input and output packet containing 20 bytes results
in 160 bits of data being sent and therefore, a transmission of 63 packets is equivalent to 10,000 bits. A BER of 10–4
implies 1 bit error for every 10000 bits sent or received. Assuming the best case of only 1 bit error in a failed packet,
having 1 failed packet for every 63 received is about equal to a BER of 10–4.
5.3.17.3 Unreturned messages alarm CH1(2)

SETTINGS  PRODUCT SETUP  DIRECT I/O  UNRETURNED MESSAGES ALARM CH1(2)
 UNRETURNED UNRET MSGS ALARM CH1 Range: Enabled, Disabled
 MESSAGES ALARM CH1  FUNCTION: Disabled
UNRET MSGS ALARM CH1 Range: 100 to 10000 in steps of 1


5 MESSAGE COUNT: 600
UNRET MSGS ALARM CH1 Range: 1 to 1000 in steps of 1

 THRESHOLD: 10
UNRET MSGS ALARM CH1 Range: Enabled, Disabled

The B90 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring
configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned
messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of
unreturned messages. This function counts all the outgoing messages and a separate counter adds the messages have
failed to return. When the unreturned messages counter reaches the user-definable level specified by the UNRET MSGS
ALARM CH1 THRESHOLD setting and within the user-defined message count UNRET MSGS ALARM CH1 COUNT, the DIR IO CH1
UNRET ALM FlexLogic operand is set.
When the total message counter reaches the user-defined maximum specified by the UNRET MSGS ALARM CH1 MESSAGE
COUNT setting, both the counters reset and the monitoring process is restarted.
Configure the operand to drive an output contact, user-programmable LED, or selected communication-based output.
Latching and acknowledging conditions, if required, are programmed accordingly.
The unreturned messages alarm function is available on a per-channel basis and is active only in the ring configuration.
The total number of unreturned input and output messages is available as the ACTUAL VALUES  STATUS  DIRECT INPUTS
 UNRETURNED MSG COUNT CH1 actual value.
5.3.18 Installation
SETTINGS  PRODUCT SETUP  INSTALLATION
 INSTALLATION RELAY SETTINGS: Range: Not Programmed, Programmed
  Not Programmed
RELAY NAME: Range: up to 20 alphanumeric characters

 Relay-1

CHAPTER 5: SETTINGS SYSTEM SETUP
RELAY SETTINGS — To safeguard against the installation of a relay without any entered settings, the unit does not allow
signaling of any output relay until RELAY SETTINGS is set to "Programmed." This setting is "Not Programmed" by default. The
UNIT NOT PROGRAMMED self-test error message displays until the relay is put into the "Programmed" state.
RELAY NAME — This setting allows the user to uniquely identify a relay. This name appears on generated reports.
5.4 System setup

5.4.1 AC inputs
5.4.1.1 Current terminals

SETTINGS  SYSTEM SETUP  AC INPUTS  CURRENT TERMINAL F1(S8)
 CURRENT CT F1 PRIMARY: Range: 1 to 65000 A in steps of 1
 TERMINAL F1  65000 A
CT F1 SECONDARY: Range: 1 A, 5 A
 1A
This menu configures the AC current inputs. Upon power up, the B90 recognizes all the AC modules loaded in its chassis
and populates the above menu accordingly.
The current terminals are denoted in the following format: Xa, where X = {F, L, S} and a = (1, 2,..., 8}. X represents the chassis
slot containing the AC input module and a represents the AC channel of each module. For example, a B90 unit containing
the F8H and L8K modules displays the following current inputs for configuration: F1, F2, F3, F4, F5, F6, F7, F8, L1, L2, L3, L4,
L5, L6, and L7. 5
5.4.1.2 Voltage terminals
SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE TERMINAL F1(S8)
 VOLTAGE VT F1 SECONDARY: Range: 50.0 to 240.0 V in steps of 0.1
 TERMINAL F1  66.4 V
VT F1 RATIO: Range: 1.00 to 24000.00 :1 in steps of 1.00

 1.00 :1
This menu configures the AC voltage inputs. Upon power up, the B90 recognizes all the AC modules loaded in its chassis
and populates the above menu accordingly.
The voltage terminals are denoted in the following format: Xa, where X = {F, L, S} and a = (5, 6, 7, 8}. X represents the chassis
slot containing the AC input module and a represents the AC channel of each module. For example, a B90 unit containing
the F8F and L8K modules displays the following voltage inputs: F5, F6, F7, F8, and L8.
The nominal VT F1 SECONDARY setting is the voltage across the relay input terminals when nominal voltage is
applied to the VT primary.
5.4.2 Power system

SETTINGS  SYSTEM SETUP  POWER SYSTEM
 POWER SYSTEM NOMINAL FREQUENCY: Range: 25 to 60 Hz in steps of 1
  60 Hz
FREQUENCY AND PHASE Range: available CT and VT channels

 REFERENCE: F1

SYSTEM SETUP CHAPTER 5: SETTINGS
FREQUENCY TRACKING: Range: Disabled, Enabled

 Enabled
NOMINAL FREQUENCY — Used as a default to set the digital sampling rate if the system frequency cannot be measured from
available signals. This can happen if the signals are not present or are heavily distorted. Before reverting to the nominal
frequency, the frequency tracking algorithm holds the last valid frequency measurement for a safe period of time while
waiting for the signals to reappear or for the distortions to decay.
FREQUENCY AND PHASE REFERENCE — Determines which AC signal is used for phase angle reference.
The phase reference and frequency tracking AC signals are selected based upon the configuration, regardless of whether
or not a particular signal is actually applied to the relay.
Phase angle of the reference signal always displays zero degrees and all other phase angles are relative to this signal. If the
pre-selected reference signal is not measurable at a given time, the phase angles are not referenced.
The phase angle referencing is done via a phase locked loop, which can synchronize independent UR-series relays if they
have the same AC signal reference. This results in very precise correlation of time tagging in the event recorder between
different UR-series relays, provided that the relays have an IRIG-B connection.
FREQUENCY TRACKING — Set to Disabled only in very unusual circumstances; consult the factory for special variable-
frequency applications.
5.4.3 FlexCurves
5.4.3.1 Settings
SETTINGS  SYSTEM SETUP  FLEXCURVES  FLEXCURE A(D)
5  FLEXCURVE A
  FLEXCURVE A TIME AT
0.00 xPKP: 0 ms
Range: 0 to 65535 ms in steps of 1
FLEXCURVE A TIME AT Range: 0 to 65535 ms in steps of 1

 0.05 xPKP: 0 ms

FLEXCURVE A TIME AT Range: 0 to 65535 ms in steps of 1
 20.00xPKP: 0 ms
FlexCurves A through D have settings for entering times to reset and operate at the following pickup levels: 0.00 to 0.98
and 1.03 to 20.00. This data is converted into two continuous curves by linear interpolation between data points. To enter
a custom FlexCurve, enter the reset and operate times (using the VALUE keys) for each selected pickup point (using the
MESSAGE up/down keys) for the required protection curve (A, B, C, or D).

Table 5-17: FlexCurve table

Reset Time Reset Time Operate Time Operate Time Operate Time Operate Time
ms ms ms ms ms ms
0.00 0.68 1.03 2.9 4.9 10.5
0.05 0.70 1.05 3.0 5.0 11.0
0.10 0.72 1.1 3.1 5.1 11.5
0.15 0.74 1.2 3.2 5.2 12.0
0.20 0.76 1.3 3.3 5.3 12.5
0.25 0.78 1.4 3.4 5.4 13.0
0.30 0.80 1.5 3.5 5.5 13.5
0.35 0.82 1.6 3.6 5.6 14.0
0.40 0.84 1.7 3.7 5.7 14.5
0.45 0.86 1.8 3.8 5.8 15.0
0.48 0.88 1.9 3.9 5.9 15.5
0.50 0.90 2.0 4.0 6.0 16.0
0.52 0.91 2.1 4.1 6.5 16.5
0.54 0.92 2.2 4.2 7.0 17.0
0.56 0.93 2.3 4.3 7.5 17.5
0.58 0.94 2.4 4.4 8.0 18.0
0.60 0.95 2.5 4.5 8.5 18.5
0.62 0.96 2.6 4.6 9.0 19.0
0.64 0.97 2.7 4.7 9.5 19.5
0.66 0.98 2.8 4.8 10.0 20.0 5
The relay using a given FlexCurve applies linear approximation for times between the user-entered points. Take
care when setting the two points that are close to the multiple of pickup of 1; that is, 0.98 pu and 1.03 pu. It is
recommended to set the two times to a similar value, otherwise the linear approximation can result in undesired
behavior for the operating quantity that is close to 1.00 pu.
5.4.3.2 FlexCurve configuration with EnerVista software

The EnerVista software allows for easy configuration and management of FlexCurves and their associated data points.
Prospective FlexCurves can be configured from a selection of standard curves to provide the best approximate fit, then
specific data points can be edited afterwards. Alternately, curve data can be imported from a specified file (.csv format) by
selecting the EnerVista Import Data From setting (Settings > System Setup > FlexCurves > FlexCurve).
Curves and data can be exported, viewed, and cleared by clicking the appropriate buttons. FlexCurves are customized by
editing the operating time (ms) values at pre-defined per-unit current multiples. Note that the pickup multiples start at zero
(implying the "reset time"), operating time below pickup, and operating time above pickup.
5.4.3.3 Recloser curve editing

Recloser curve selection is special in that recloser curves can be shaped into a composite curve with a minimum response
time and a fixed time above a specified pickup multiples. There are 41 recloser curve types supported. These definite
operating times are useful to coordinate operating times, typically at higher currents and where upstream and
downstream protective devices have different operating characteristics. The recloser curve configuration window shown
here appears when the Initialize From setting in the EnerVista software is set to “Recloser Curve” and the Initialize
FlexCurve button is clicked.

Figure 5-62: Recloser curve initialization
Multiplier: Scales (multiplies) the curve operating times
Addr: Adds the time specified in this field (in ms) to each
curve operating time value.
Minimum Response Time (MRT): If enabled, the MRT setting

defines the shortest operating time even if the curve suggests
a shorter time at higher current multiples. A composite operating
characteristic is effectively defined. For current multiples lower
than the intersection point, the curve dictates the operating time;
otherwise, the MRT does. An information message appears
when attempting to apply an MRT shorter than the minimum
curve time.
High Current Time: Allows the user to set a pickup multiple

from which point onwards the operating time is fixed. This is
normally only required at higher current levels. The HCT Ratio
defines the high current pickup multiple; the HCT defines the
operating time.
842721A1.CDR
The Multiplier and Adder settings only affect the curve portion of the characteristic and not the MRT and HCT
settings. The HCT settings override the MRT settings for multiples of pickup greater than the HCT ratio.
5.4.3.4 Example
5 A composite curve can be created from the GE_111 standard with MRT = 200 ms and HCT initially disabled and then
enabled at eight times pickup with an operating time of 30 ms. At approximately four times pickup, the curve operating
time is equal to the MRT and from then onwards the operating time remains at 200 ms.
Figure 5-63: Composite recloser curve with HCT disabled
842719A1.CDR
With the HCT feature enabled, the operating time reduces to 30 ms for pickup multiples exceeding eight times pickup.

Figure 5-64: Composite recloser curve with HCT enabled
842720A1.CDR
Configuring a composite curve with an increase in operating time at increased pickup multiples is not allowed. If
this is attempted, the EnerVista software generates an error message and discards the proposed changes.
5.4.3.5 Standard recloser curves

The following graphs display standard recloser curves available for the B90.
Figure 5-65: Recloser curves GE101 to GE106
5
2
1 GE106
0.5
0.2
TIME (sec)
GE103
GE104 GE105
0.1
0.05
GE101 GE102
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
CURRENT (multiple of pickup) 842723A1.CDR

Figure 5-66: Recloser curves GE113, GE120, GE138, and GE142
50
20 GE142
10
5
GE138
TIME (sec)
1 GE120
GE113
0.5
0.2
0.1
0.05
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
5
Figure 5-67: Recloser curves GE134, GE137, GE140, GE151, and GE201
50
20
10
GE201
TIME (sec)
GE151
2
GE134 GE140
1
GE137
0.5
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20


Figure 5-68: Recloser curves GE131, GE141, GE152, and GE200
50
GE152
20
TIME (sec)
GE141
10
GE131
5
GE200
2
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
5
Figure 5-69: Recloser curves GE133, GE161, GE162, GE163, GE164, and GE165
50
20
GE164
10
2
TIME (sec)
GE162
1
0.5
GE133
0.2
GE165
0.1
0.05
GE161
0.02 GE163
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20

Figure 5-70: Recloser curves GE116, GE117, GE118, GE132, GE136, and GE139
20
GE132
10
1
TIME (sec)
0.5 GE139
0.2
GE136
0.1
GE116
0.05
GE118 GE117
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
5
Figure 5-71: Recloser curves GE107, GE111, GE112, GE114, GE115, GE121, and GE122
20
10
5
GE122
2
1
TIME (sec)
0.5
GE114
0.2
GE111
GE121
0.1
0.05 GE115 GE112

GE107
0.02
0.01
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20

Figure 5-72: Recloser curves GE119, GE135, and GE202
50
20
GE202
10
TIME (sec)
GE135
2 GE119
0.5
0.2
1 1.2 1.5 2 2.5 3 4 5 6 7 8 9 10 12 15 20
5
5.4.4 Bus
SETTINGS  SYSTEM SETUP  BUS  BUS ZONE 1(6)  BUS ZONE 1(6) INPUT A(X)
 BUS ZONE 1 INPUT A BUS 1A CT: Range: available CT channels
  F1
BUS 1A DIRECTION: Range: IN, OUT

 IN
BUS 1A STATUS: Range: FlexLogic operand

 Off
The number of available zones and their size (maximum number of inputs) are optional and controlled by the
software option portion of the order code. See the Order Codes section in chapter 2 for information on the
maximum number of zones and inputs for a given B90 model.
Six bus differential zones are available. Each zone is associated with its own bus differential protection and CT trouble
monitoring elements. A differential zone is defined by up to 24 pairs (inputs A to X) of current input–bus connection status
values.
BUS 1A CT — This setting defines a current input to the zone. Selections include all the CT channels available in the relay as
per configured hardware. The protected bus zone is uniquely identified as the portion of the bus between the selected
current sources (CTs).
BUS 1A DIRECTION — This setting configures the CT orientation with respect to the protected zone. Bus differential and CT
trouble decisions are based on current summation and thus correct orientation selection is important. The following figure
shows a tie-breaker dividing a single bus into two sections, defined as zone 1 and zone 2. The tie-breaker CT (F5) is
common to both zones and therefore the respective direction settings are opposite. The CT polarity dots are in relation to
the protected zone and are terminated to the “common” of the tapped (1 A / 5 A) inputs. The polarity dots for the zone 2 CTs
face outward with respect to the bus; as such, the F5 to F8 direction settings are “IN”. Similarly, the F1 to F4 CTs for zone 1
are selected as “IN.” However, the polarity dot orientation for the F5 CT faces inward with respect to zone 1 and therefore
the BUS 1E DIRECTION setting is “OUT.”

BUS 1A STATUS — This setting dynamically defines a connection status of a given feeder with respect to the differential zone
(dynamic bus replica). If a given feeder is connected to the zone and its current included into differential calculations, the
FlexLogic operand used for this setting is “On.” If the current is excluded, the FlexLogic operand is “Off.” Typically, this
setting is an appropriately filtered position of an isolator, a breaker, or a tie-breaker.
In the case of an isolator connecting a feeder to a given section of a bus, the isolator monitoring feature produces a
reliable isolator position operand (ISOLATOR 1 POSITION). Typically, the isolator monitoring feature is enabled in the fourth
B90 IED and the ISOLATOR 1 POSITION status operand must be sent over direct input/output communications before it can
be configured as a BUS ZONE 1A(X) STATUS setting.
Figure 5-73: Bus zone direction setting
ZONE 1 F5 ZONE 2
F1 F2 F3 F4 F6 F7 F8
ZONE 1: ZONE 2:
BUS 1A CT = F1 BUS 2A CT = F5
BUS 1A DIRECTION = IN BUS 2A DIRECTION = IN
BUS 1B CT = F2 BUS 2B CT = F6
BUS 1B DIRECTION = IN BUS 2B DIRECTION = IN
BUS 1C CT = F3 BUS 2C CT = F7
BUS 1C DIRECTION = IN BUS 2C DIRECTION = IN
BUS 1D CT = F4 BUS 2D CT = F8
BUS 1D DIRECTION = IN BUS 2D DIRECTION = IN
5
BUS 1E CT = F5
BUS 1E DIRECTION = OUT
836757A2.CDR
For example, assume that B90 IED 4 is used for isolator monitoring while IEDs 1, 2, and 3 are used for protection.
Consequently, the B90 FUNCTION setting of IED 4 must be set to “Logic” while B90 FUNCTION on the IEDs 1, 2 and 3 must be
set to “Protection.” Normally open and closed auxiliary switches of a given isolator must be wired to the IED 4, and the
Isolator feature must be enabled and configured appropriately.
Assume that the isolator shown as follows is monitored by the Isolator 1 feature. The ISOLATOR 1 POSITION is the FlexLogic
operand asserted by the isolator 1 monitoring element. This operand must be configured to drive a direct output in order
to send the connection status to IEDs 1, 2, and 3 where the bus replica is being utilized by differential protection. Assume
bit 12 of the message originating at IED 4 is used for this purpose. This is achieved by applying the following settings:
For IED 4:
DIRECT OUTPUT DEVICE ID: “4” (this is the originating device)
DIRECT OUT 12 OPERAND: “ISOLATOR 1 POSITION” (this operand drives output number 12)
The above information is to be received by IEDs 1, 2, and 3. Assume direct input 68 is to reflect the isolator position.
For IEDs 1, 2, and 3:
DIRECT INPUT 68 DEVICE: “4” (message received from IED 4)
DIRECT INPUT 68 BIT NUMBER: “12” (using bit number 12)
Once received, the isolator 1 status (known on IEDs 1, 2, and 3 as DIRECT INPUT 68 On) is used for bus configuration.
For IEDs 1, 2, and 3:
BUS 1E CT: “F7” (the current wired to the F7 terminal)
BUS 1E STATUS: “DIRECT INPUT 68 On”

CHAPTER 5: SETTINGS FLEXLOGIC
Figure 5-74: Direct input and output sample configuration for dynamic bus replica
ZONE 2
ZONE 1
ISO 1 ISOLATOR 1 POSITION
normally open and closed IED 4

auxiliary switches
sent as bit no.12 from IED no.4

phase A current, wired to F7 IED 1
phase B current, wired to F7 IED 2
IED 3
phase C current, wired to F7
Received as DIRECT
INPUT 68 On
BUS 1E CT = F7
BUS 1E STATUS = DIRECT INPUT 68 On
836758A2.CDR
In the case of a breaker (or a tie-breaker), a breaker closed position with a dropout time of 40 to 60 ms is typically used as
a connection status to avoid over-tripping or dead zones, depending on the relative position of the breaker and CT. See the
Application of Settings chapter for details on configuring bus differential zones. 5
5.5 FlexLogic
5.5.1 FlexLogic operands
For flexibility, the arrangement of internal digital logic combines fixed and user-programmed parameters. Logic upon
which individual features are designed is fixed, and all other logic, from contact input signals through elements or
combinations of elements to contact outputs, is variable. The user has complete control of all variable logic through
FlexLogic. In general, the system receives analog and digital inputs that it uses to produce analog and digital outputs. The
figure shows major subsystems of a generic UR-series relay involved in this process.

FLEXLOGIC CHAPTER 5: SETTINGS
Figure 5-75: UR architecture overview
CTs DSP
VTs (A/D) FlexLogic™ Virtual
equations outputs
Calculate
DCmA parameters Measuring
Analog and
or
input decision Digital Flags
RTD
(A/D) elements elements
inputs
V I
Contact Form-A and
inputs FlexLogic™ SCR only
Block counters
operation Contact
(each outputs
element)
Keypad
Virtual Remote
inputs (FlexLogic operands) outputs
OR
Remote Display
inputs Control and LEDs
(GOOSE) and Display
monitoring
features
fiber Analog
Direct output (D/A)
G.703 inputs
RS422 (dcmA)
5 (Status) Direct
outputs
Fiber
G.703
RS422
(Actual values) (Status)
EnerVista UR Setup and LAN communications
827022A7.cdr
The states of all digital signals used in the B90 are represented by flags (or FlexLogic operands, which are described later in
this section). A digital “1” is represented by a set flag. Any external contact change-of-state can be used to block an
element from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output. The state
of the contact input can be displayed locally or viewed remotely via the communications facilities provided. If a simple
scheme where a contact input is used to block an element is wanted, this selection is made when programming the
element. This capability also applies to the other features that set flags: elements, virtual inputs, remote inputs, schemes,
and human operators.
If more complex logic than shown in the figure is required, it is implemented via FlexLogic. For example, to have the closed
state of contact input H7a and the operated state of the phase undervoltage element block the operation of the phase
time overcurrent element, the two control input states are programmed in a FlexLogic equation. This equation ANDs the
two control inputs to produce a virtual output that is then selected when programming the phase time overcurrent to be
used as a blocking input. Virtual outputs can only be created by FlexLogic equations.
Traditionally, protective relay logic has been relatively limited. Any unusual applications involving interlocks, blocking, or
supervisory functions had to be hard-wired using contact inputs and outputs. FlexLogic minimizes the requirement for
auxiliary components and wiring while making more complex schemes possible.
The logic that determines the interaction of inputs, elements, schemes, and outputs is field-programmable through the use
of logic equations that are sequentially processed. The use of virtual inputs and outputs in addition to hardware is
available internally and on the communication ports for other relays to use (distributed FlexLogic).
FlexLogic allows users to customize the relay through a series of equations that consist of operators and operands. The
operands are the states of inputs, elements, schemes, and outputs. The operators are logic gates, timers, and latches (with
set and reset inputs). A system of sequential operations allows any combination of operands to be assigned as inputs to

specified operators to create an output. The final output of an equation is a numbered register called a virtual output.
Virtual outputs can be used as an input operand in any equation, including the equation that generates the output, as a
seal-in or other type of feedback.
A FlexLogic equation consists of parameters that are either operands or operators. Operands have a logic state of 1 or 0.
Operators provide a defined function, such as an AND gate or a Timer. Each equation defines the combinations of
parameters to be used to set a Virtual Output flag. Evaluation of an equation results in either a 1 (=ON, or flag set) or 0
(=OFF, or flag not set). Each equation is evaluated at least four times every power system cycle.
Some types of operands are present in the relay in multiple instances, for example contact and remote inputs. These types
of operands are grouped together (for presentation purposes only) on the front panel display. The table lists characteristics
of the different types of operands.
Table 5-18: B90 FlexLogic operand types
Operand type State Example of format Characteristics
[Input Is ‘1’ (= ON) if...]
Contact Input On Cont Ip On Voltage is applied presently to the input (external contact
closed)
Off Cont Ip Off Voltage is not applied presently to the input (external
contact open)
Contact Output Contact Closed Cont Op 1 Closed Contact output is closed
(type Form-A contact
Current On Cont Op 1 Ion Current is flowing through the contact
only)
Voltage On Cont Op 1 VOn Voltage exists across the contact
Voltage Off Cont Op 1 VOff Voltage does not exist across the contact
Direct Input On DIRECT INPUT 1 On The direct input is presently in the ON state
Element Pickup PHASE TOC1 PKP The tested parameter is presently above the pickup setting
(Analog) of an element that responds to rising values or below the
pickup setting of an element that responds to falling values
5
Dropout PHASE TOC1 DPO This operand is the logical inverse of the above PKP
operand
Operate PHASE TOC1 OP The tested parameter has been above/below the pickup
setting of the element for the programmed delay time, or
has been at logic 1 and is now at logic 0 but the reset timer
has not finished timing
Block PHASE TOC1 BLK The output of the comparator is set to the block function
Element Pickup Dig Element 1 PKP The input operand is at logic 1
(Digital)
Dropout Dig Element 1 DPO This operand is the logical inverse of the above PKP
operand
Operate Dig Element 1 OP The input operand has been at logic 1 for the programmed
pickup delay time, or has been at logic 1 for this period and
is now at logic 0 but the reset timer has not finished timing
Fixed On On Logic 1
Off Off Logic 0
RxGOOSE Boolean On RxGOOSE Boolean 1 On The RxGOOSE Boolean is presently in the ON state
Virtual Input On Virt Ip 1 On The virtual input is presently in the ON state
Virtual Output On Virt Op 1 On The virtual output is presently in the set state (that is,
evaluation of the equation that produces this virtual output
results in a "1")
The following table lists the operands available for the relay. The operands can be viewed online by entering the IP address
of the relay in a web browser and accessing the Device Information Menu.
Table 5-19: B90 FlexLogic operands
Operand type Operand syntax Operand description
ANNUNCIATOR ANY ANCTR ABNORMAL On for one second when any annunciator window state changes from
Graphical front panel normal to abnormal
ANY ANCTR ALARMED On while any annunciator window state is abnormal


CONTROL CONTROL PUSHBTN 1 ON Control pushbutton 1 is being pressed
PUSHBUTTONS CONTROL PUSHBTN 2 ON Control pushbutton 2 is being pressed
Enhanced and basic CONTROL PUSHBTN 3 ON Control pushbutton 3 is being pressed
front panels CONTROL PUSHBTN 4 ON Control pushbutton 4 is being pressed
CONTROL PUSHBTN 5 ON Control pushbutton 5 is being pressed
CYBERSENTRY ROLE ADMIN ACT Administrator role is active and is set to true when that is the case
ROLE SUPERVISOR ACT Supervisor role is active and is set to true when that is the case
ROLE ENGINEER ACT Engineer role is active and is set to true when that is the case
ROLE OPERATOR ACT Operator role is active and is set to true when that is the case
ROLE OBSERVER ACT Observer role is active and is set to true when that is the case
AUTHENTICATION FAIL Operand set for Failed Authentication self-test and alarm
UNAUTH FW ATTEMPT Operand set for firmware lock self-test and alarm
UNAUTH SETTING WRITE Operand set for settings lock self-test and alarm
DIRECT DEVICES DIRECT DEVICE 1On Flag is set, logic=1
 
DIRECT DEVICE 16On Flag is set, logic=1
DIRECT DEVICE 1Off Flag is set, logic=1
 
DIRECT DEVICE 16Off Flag is set, logic=1
DIRECT INPUT/ DIR IO CH1 CRC ALARM The rate of direct input messages received on channel 1 and failing the CRC
OUTPUT CHANNEL exceeded the user-specified level
MONITORING DIR IO CH2 CRC ALARM The rate of direct input messages received on channel 2 and failing the CRC
exceeded the user-specified level
DIR IO CH1 UNRET ALM The rate of returned direct input/output messages on channel 1 exceeded
the user-specified level (ring configurations only)
DIR IO CH2 UNRET ALM The rate of returned direct input/output messages on channel 2 exceeded
the user-specified level (ring configurations only)
5 ELEMENT:
Breaker failure
BKRFAIL 1 RETRIP
BKRFAIL 1 T1 OP
Re-trip issued by the breaker failure 1 protection
Timer 1 of the breaker failure 1 protection expired
BKRFAIL 1 T2 OP Timer 2 of the breaker failure 1 protection expired
BKRFAIL 1 T3 OP Timer 3 of the breaker failure 1 protection expired
BKRFAIL 1 TRIP OP Breaker failure 1 has operated
BKRSUPV 1 SUPV OP Overcurrent supervision of the breaker failure 1 operated
BKRSUPV 1 HISET OP High-set overcurrent supervision of the breaker failure 1 operated
BKRSUPV 1 LOSET OP Low-set overcurrent supervision of the breaker failure 1 operated
BKRFAIL 2 to 24 Same set of operands as shown for BKRFAIL1
BKRSUPV 2 to 24 Same set of operands as shown for BKRSUPV 1
ELEMENT: BUS 1 BIASED PKP The biased bus differential element for zone 1 has picked up
Bus differential BUS 1 BIASED DPO The biased bus differential element for zone 1 has dropped out
BUS 1 BIASED OP The biased bus differential element for zone 1 has operated
BUS 1 UNBIASED OP The unbiased bus differential element for zone 1 has operated
BUS 1 OP The bus differential element for zone 1 has operated
BUS 1 DIR The directional unit for the zone 1 bus differential element has issued
permission to operate
BUS 1 SAT The saturation detector for the zone 1 bus differential element has detected
external fault conditions
BUS 2 to 6 Same set of operands as shown for BUS 1
ELEMENT: CT TROUBLE 1 OP CT trouble has been detected for bus differential zone 1
CT trouble CT TROUBLE 2 OP CT trouble has been detected for bus differential zone 2
CT TROUBLE 3 OP CT trouble has been detected for bus differential zone 3
ELEMENT: Dig Element 1 PKP Digital Element 1 is picked up
Digital elements Dig Element 1 OP Digital Element 1 is operated
Dig Element 1 DPO Digital Element 1 is dropped out
Dig Element 2 to 48 Same set of operands as shown for Dig Element 1
ELEMENT: EFP 1 PKP The first end fault protection element has picked up
End fault protection EFP 1 DPO The first end fault protection element has dropped out
EFP 1 OP The first end fault protection element has operated
EPF 2 to 24 Same set of operands as shown for EFP 1


ELEMENT: IOC 1 PKP Instantaneous overcurrent 1 element has picked up
Instantaneous IOC 1 DPO Instantaneous overcurrent 1 element has dropped out
overcurrent IOC 1 OP Instantaneous overcurrent 1 element has operated
IOC 2 to 24 Same set of operands as shown for IOC 1
ELEMENT: ISOLATOR 1 POSITION Position of isolator 1 (ON = closed; OFF = open)
Isolator monitoring ISOLATOR 1 ALARM Contact discrepancy detected for isolator 1
ISOLATOR 1 BLOCK Blocking signal for substation switching operations set due to contact
discrepancy of isolator 1 (acknowledgeable)
ISOLATOR 2 to 48 Same set of operands as shown for ISOLATOR 1
ELEMENT: LATCH 1 ON Non-volatile latch 1 is ON (Logic = 1)
Non-volatile latches LATCH 1 OFF Non-volatile latch 1 is OFF (Logic = 0)
LATCH 2 to 16 Same set of operands as shown for LATCH 1
ELEMENT: SETTING GROUP ACT 1 Setting group 1 is active
Setting group SETTING GROUP ACT 2 Setting group 2 is active
SETTING GROUP ACT 3 Setting group 3 is active
ELEMENT: TOC 1 PKP The time overcurrent 1 element has picked up
Time overcurrent TOC 1 DPO The time overcurrent 1 element has dropped out
TOC 1 OP The time overcurrent 1 element has operated
TOC 2 to 24 Same set of operands as shown for TOC 1
ELEMENT: TRIP BUS 1 PKP Asserted when the trip bus 1 element picks up
Trip bus TRIP BUS 1 OP Asserted when the trip bus 1 element operates
TRIP BUS 2 to 6 Same set of operands as shown for TRIP BUS 1
ELEMENT:
Undervoltage
UNDERVOLTAGE 1 PKP
UNDERVOLTAGE 1 DPO
The undervoltage 1 element has picked up
The undervoltage 1 element has dropped out
5
UNDERVOLTAGE 1 OP The undervoltage 1 element has operated
UNDERVOLTAGE 2 to 12 Same set of operands as shown for UNDERVOLTAGE 1
FIXED OPERANDS Off Logic = 0. Does nothing and can be used as a delimiter in an equation list;
used as ‘Disable’ by other features.
On Logic = 1. Can be used as a test setting.
INPUTS/OUTPUTS: Cont Ip 1 On (does not appear unless ordered)
Contact inputs Cont Ip 2 On (does not appear unless ordered)
 
Cont Ip 1 Off (does not appear unless ordered)
 
Cont Ip 120 On (does not appear unless ordered)
INPUTS/OUTPUTS: Cont Op 1 IOn (does not appear unless ordered)
Contact outputs, Cont Op 2 IOn (does not appear unless ordered)
current  
(from detector on Cont Op 72 IOn (does not appear unless ordered)
form-A output only)
INPUTS/OUTPUTS: Cont Op 1 VOn (does not appear unless ordered)
Contact outputs, Cont Op 2 VOn (does not appear unless ordered)
voltage  
(from detector on Cont Op 72 VOn (does not appear unless ordered)
form-A output only)
Cont Op 1 VOff (does not appear unless ordered)
 
INPUTS/OUTPUTS: DIRECT INPUT 1 On Flag is set, logic=1
Direct inputs  
DIRECT INPUT 256 On Flag is set, logic=1


INPUTS/OUTPUTS: RxG DPS 1 BAD Asserted while the RxGOOSE double-point status input is in the bad state
RxGOOSE DPS RxG DPS 1 INTERM Asserted while the RxGOOSE double-point status input is in the intermediate
state
RxG DPS 1 OFF Asserted while the RxGOOSE double-point status input is off
RxG DPS 1 ON Asserted while the RxGOOSE double-point status input is on
RxG DPS 2 to 5 Same set of operands as per RxG DPS 1
INPUTS/OUTPUTS: RxG Bool 1 On Flag is set, logic=1
RxGOOSE Booleans RxG Bool 2 On Flag is set, logic=1
RxG Bool 3 On Flag is set, logic=1
 
RxG Bool 256 On Flag is set, logic=1
INPUTS/OUTPUTS: Virt Ip 1 On Flag is set, logic=1
Virtual inputs Virt Ip 2 On Flag is set, logic=1
Virt Ip 3 On Flag is set, logic=1
 
Virt Ip 64 On Flag is set, logic=1
INPUTS/OUTPUTS: Virt Op 1 On Flag is set, logic=1
Virtual outputs Virt Op 2 On Flag is set, logic=1
Virt Op 3 On Flag is set, logic=1
 
Virt Op 96 On Flag is set, logic=1
LED INDICATORS: LED IN SERVICE Asserted when the front panel IN SERVICE LED is on
Enhanced and basic LED TROUBLE Asserted when the front panel TROUBLE LED is on
front panels LED TEST MODE Asserted when the front panel TEST MODE LED is on
LED TRIP Asserted when the front panel TRIP LED is on
LED ALARM Asserted when the front panel ALARM LED is on
LED PICKUP Asserted when an element picks up and to turn PICKUP LED on
LED VOLTAGE Asserted when a voltage element involved and to turn VOLTAGE LED on
5 LED CURRENT
LED FREQUENCY
Asserted when a current element involved and to turn CURRENT LED on
Asserted when a frequency element involved and to turn FREQUENCY LED on
LED OTHER Asserted when a composite element involved and to turn OTHER LED on
LED PHASE A Asserted when phase A involved and to turn PHASE A LED on
LED PHASE B Asserted when phase B involved and to turn PHASE B LED on
LED PHASE C Asserted when phase C involved and to turn PHASE C LED on
LED NEUTRAL/GROUND Asserted when a neutral or ground element involved and to turn NEUTRAL/
GROUND LED on
LED INDICATORS: LED IN SERVICE Asserted when the front panel IN SERVICE LED is on
Graphical front panel LED TROUBLE Asserted when the front panel TROUBLE LED is on
LED TEST MODE Asserted when the front panel TEST MODE LED is on
LED TRIP Asserted when the front panel TRIP LED is on
LED ALARM Asserted when the front panel ALARM LED is on
LED PICKUP Asserted when an element picks up and to turn Event Cause LED 1 on by
default
LED VOLTAGE Asserted when a voltage element involved and to turn Event Cause LED 2 on
by default
LED CURRENT Asserted when a current element involved and to turn Event Cause LED 3 on
by default
LED FREQUENCY Asserted when a frequency element involved and to turn Event Cause LED 4
on by default
LED OTHER Asserted when a composite element involved and to turn Event Cause LED 5
on by default
LED PHASE A Asserted when phase A involved and to turn Event Cause LED 6 on by default
LED PHASE B Asserted when phase B involved and to turn Event Cause LED 7 on by default
LED PHASE C Asserted when phase C involved and to turn Event Cause LED 8 on by default
LED NEUTRAL/GROUND Asserted when a neutral or ground element involved and to turn Event Cause
LED 9 on by default
LED INDICATORS: LED TEST IN PROGRESS An LED test has been initiated and has not finished
LED test
LED INDICATORS: LED USER 1 Asserted when user-programmable LED 1 is on
User-programmable
LEDs
Enhanced and basic
front panels
LED USER 2 to 48 The operand above is available for user-programmable LEDs 2 through 48


LED INDICATORS: EVENT CAUSE LED 1 Asserted when event cause LED 1 is on
User-programmable
EVENT CAUSE LED 2 to 9 Same operand as EVENT CAUSE LED 1
LEDs
Graphical front panel
PASSWORD ACCESS LOC SETG OFF Asserted when local setting access is disabled
SECURITY ACCESS LOC SETG ON Asserted when local setting access is enabled
ACCESS LOC CMND OFF Asserted when local command access is disabled
ACCESS LOC CMND ON Asserted when local command access is enabled
ACCESS REM SETG OFF Asserted when remote setting access is disabled
ACCESS REM SETG ON Asserted when remote setting access is enabled
ACCESS REM CMND OFF Asserted when remote command access is disabled
ACCESS REM CMND ON Asserted when remote command access is enabled
UNAUTHORIZED ACCESS Asserted when a password entry fails while accessing a password protected
level of the B90
RxGOOSE RxGOOSE 1 On Flag is set, logic=1
 
RxGOOSE 64 On Flag is set, logic=1
RxGOOSE 1 Off Flag is set, logic=1
 
RxGOOSE 64 Off Flag is set, logic=1
<RxGOOSE Boolean1 ID> On Replace bracketed text with RxGOOSE Boolean1 status of "true"
<RxGOOSE DPS1 ID> Bad Replace bracketed text with RxGOOSE DPS1 status of "bad-state"
<RxGOOSE DPS1 ID> Interm Replace bracketed text with RxGOOSE DPS1 status is "intermediate-state"
<RxGOOSE DPS1 ID> Off Replace bracketed text with RxGOOSE DPS1 status is "off"
<RxGOOSE DPS1 ID> On Replace bracketed text with RxGOOSE DPS1 status is "on"
RxGOOSE INVLD ON One or more Rx GOOSE Inputs are received with Invalid quality
RxGOOSE QUES ON One or more Rx GOOSE Inputs are received with questionable quality
RxGOOSE INVLD ON and RxGOOSE QUES ON operands have no dependency

with test mode or simulation mode. The operands are set when any of the
RxGOOSE Inputs received with Invalid or questionable quality.
5
RESETTING RESET OP Reset command is operated (set by all three operands below)
RESET OP (COMMS) Communications source of the reset command
RESET OP (OPERAND) Operand (assigned in the INPUTS/OUTPUTS  RESETTING menu) source of
the reset command
RESET OP (PUSHBUTTON) Reset key (pushbutton) source of the reset command
RESET ANCTR OP Reset annunciator command is operated (set by any operands below)
RESET ANCTR OP(OPRD) Reset operand (assigned in INPUTS/OUTPUTS  RESETTING
ANNUNCIATOR menu) source of the reset annunciator command
RESET ANCTR OP(MNUL) Reset manual (pushbutton or EnerVista software) source of the reset
annunciator command
SELF-DIAGNOSTICS ANY MAJOR ERROR Any of the major self-test errors generated (major error)
(See Relay Self-tests ANY MINOR ERROR Any of the minor self-test errors generated (minor error)
descriptions in ANY SELF-TESTS Any self-test errors generated (generic, any error)
Chapter 7: BATTERY FAIL The battery is weak or not functioning. Replace as outlined in the
Commands and Maintenance chapter.
Targets) CLOCK UNSYNCHRONIZED Relay is not synchronized to the international time standard
DIRECT DEVICE OFF A direct device is configured but not connected
DIRECT RING BREAK The Direct I/O settings is for a connection that is not in a ring
EQUIPMENT MISMATCH The configuration of modules does not match the stored order code
FLEXLOGIC ERR TOKEN A FlexLogic equation is incorrect
IRIG-B FAILURE "Bad IRIG-B Signal" self-test. See Chapter 7: Commands and Targets.
LATCHING OUT ERROR A difference is detected between the desired and actual latch contact state
MAINTENANCE ALERT A subset of the minor self-test errors generated, see Chapter 7
FIRST ETHERNET FAIL Link failure detected. See description in Chapter 7: Commands and Targets.
PTP FAILURE "Bad PTP Signal" self-test as described in Chapter 7
RxGOOSE OFF One or more GOOSE messages are not being received
RRTD COMM FAIL See description in Chapter 7: Commands and Targets
SECOND ETHERNET FAIL See description in Chapter 7: Commands and Targets
THIRD ETHERNET FAIL See description in Chapter 7: Commands and Targets
SNTP FAILURE SNTP server is not responding
SYSTEM EXCEPTION See description in Chapter 7: Commands and Targets
TEMP MONITOR Monitors ambient temperature and maximum operating temperature
UNIT NOT PROGRAMMED The product SETUP > INSTALLATION > RELAYS SETTINGS setting is not
programmed
SETTING CHANGED Any device settings changed over any available interface; operand is
asserted for at least one second and then self-reset


SIMULATION TxGOOSE SIM ON Sim bit enabled in all Tx GOOSE
RxGOOSE SIM ON GOOSE messages with Sim bit set are accepted
TEMPERATURE TEMP MONITOR Asserted while the ambient temperature is greater than the maximum
MONITOR operating temperature (80°C)
USER- PUSHBUTTON 1 ON Pushbutton number 1 is in the “On” position
PROGRAMMABLE PUSHBUTTON 1 OFF Pushbutton number 1 is in the “Off” position
PUSHBUTTONS ANY PB ON Any of 12 pushbuttons is in the “On” position
PUSHBUTTON 2 to 6, 12, or 16 Same set of operands as PUSHBUTTON 1
depending on front panel
Some operands can be re-named. These are the names of the breakers in the breaker control feature, the ID (identification)
of contact inputs and outputs, the ID of virtual inputs, and the ID of virtual outputs. If the user changes the default name or
ID of any of these operands, the assigned name appears in the relay list of operands. The default names are shown in the
FlexLogic operands table.
The characteristics of the logic gates are tabulated in the following table, and the operators available in FlexLogic are
listed in the FlexLogic operators table.
Table 5-20: FlexLogic gate characteristics
Gates Number of inputs Output is ‘1’ (= ON) if...
NOT 1 input is ‘0’
OR 2 to 16 any input is ‘1’
AND 2 to 16 all inputs are ‘1’
NOR 2 to 16 all inputs are ‘0’
5 NAND
XOR
2 to 16
2
any input is ‘0’
only one input is ‘1’

Table 5-21: FlexLogic operators

Type Syntax Description Notes
Editor INSERT Insert a parameter in an equation list
DELETE Delete a parameter from an equation list
End END The first END encountered signifies the last entry in
the list of processed FlexLogic parameters
One-shot POSITIVE ONE SHOT One shot that responds to a positive going edge A ‘one shot’ refers to a single input gate that
generates a pulse in response to an edge on
NEGATIVE ONE SHOT One shot that responds to a negative going edge
the input. The output from a ‘one shot’ is
DUAL ONE SHOT One shot that responds to both the positive and True (positive) for only one pass through the
negative going edges FlexLogic equation. There is a maximum of
64 ‘one shots.’
Logic NOT Logical NOT Operates on the previous parameter
gate
OR(2) 2 input OR gate Operates on the 2 previous parameters
  
OR(16) 16 input OR gate Operates on the 16 previous parameters
AND(2) 2 input AND gate Operates on the 2 previous parameters
  
AND(16) 16 input AND gate Operates on the 16 previous parameters
NOR(2) 2 input NOR gate Operates on the 2 previous parameters
  
NOR(16) 16 input NOR gate Operates on the 16 previous parameters
NAND(2) 2 input NAND gate Operates on the 2 previous parameters
  
NAND(16) 16 input NAND gate Operates on the 16 previous parameters
XOR(2) 2 input Exclusive OR gate Operates on the 2 previous parameters
LATCH (S,R) Latch (set, reset): reset-dominant The parameter preceding LATCH(S,R) is the
reset input. The parameter preceding the
5
reset input is the set input.
Timer TIMER 1 Timer set with FlexLogic timer 1 settings The timer is started by the preceding
  parameter. The output of the timer is
TIMER 32 Timer set with FlexLogic timer 32 settings TIMER #.
Assign = Virt Op 1 Assigns previous FlexLogic operand to virtual The virtual output is set by the preceding
virtual  output 1 parameter
output = Virt Op 96 
Assigns previous FlexLogic operand to virtual
output 96
5.5.2 FlexLogic rules

When forming a FlexLogic equation, the sequence in the linear array of parameters must follow these general rules:
1. Operands must precede the operator that uses the operands as inputs.
2. Operators have only one output. The output of an operator must be used to create a virtual output if it is to be used as
an input to two or more operators.
3. Assigning the output of an operator to a virtual output terminates the equation.
4. A timer operator (for example, "TIMER 1") or virtual output assignment (for example, " = Virt Op 1") can be used once
only. If this rule is broken, a syntax error is declared.
5.5.3 FlexLogic evaluation

Each equation is evaluated in the ascending order in which the parameters have been entered.

FlexLogic provides built-in latches that by definition have a memory action, remaining in the set state after the set
input has been asserted. These built-in latches are reset dominant, meaning that if logical "1" is applied to both set
and reset entries simultaneously, then the output of the latch is logical "0." However, they are volatile, meaning that
they reset upon removal of control power.
When making changes to FlexLogic entries in the settings, all FlexLogic equations are re-compiled whenever any
new FlexLogic entry value is entered, and as a result of the re-compile all latches are reset automatically.
To implement FlexLogic using a graphical user interface, see the FlexLogic Design and Monitoring using Engineer
section in the previous chapter.
5.5.4 FlexLogic example

This section provides an example of logic implementation for a typical application. The sequence of steps is important to
minimize the work to develop the relay settings. Note that the example in the following figure demonstrates the procedure,
not to solve a specific application situation.
Note that there is also a graphical interface with which to draw logic and populate FlexLogic equation entries. See the
Engineer content at the end of the previous chapter.
In the example, it is assumed that logic has already been programmed to produce virtual outputs 1 and 2, and is only a
part of the full set of equations used. When using FlexLogic, it is important to make a note of each virtual output used; a
virtual output designation (1 to 96) can be assigned only once.
Figure 5-76: Logic example
Virtual output 1
state = On
5 Virtual output 2
state = On
Set
Latch
Virtual input 1 OR #1 Reset
state = On
XOR
Digital element 1 Timer 2
state = Pickup Time Delay Operate output
OR #2
on dropout relay H1
(200 ms)
state = Operated Time delay
AND on pickup
(800 ms)
Contact input H1c
state = Closed 827025A2.CDR
1. Inspect the example logic diagram to determine if the required logic can be implemented with the FlexLogic
operators. If this is not possible, the logic must be altered until this condition is satisfied. Once done, count the inputs
to each gate to verify that the number of inputs does not exceed the FlexLogic limits, which is unlikely but possible. If
the number of inputs is too high, subdivide the inputs into multiple gates to produce an equivalent. For example, if 25
inputs to an AND gate are required, connect Inputs 1 through 16 to AND(16), 17 through 25 to AND(9), and the outputs
from these two gates to AND(2).
Inspect each operator between the initial operands and final virtual outputs to determine if the output from the
operator is used as an input to more than one following operator. If so, the operator output must be assigned as a
virtual output.
For the example shown, the output of the AND gate is used as an input to both OR#1 and Timer 1, and must therefore
be made a virtual output and assigned the next available number (that is, Virtual Output 3). The final output must also
be assigned to a virtual output as virtual output 4, which is programmed in the contact output section to operate relay
H1 (that is, contact output H1).
Therefore, the required logic can be implemented with two FlexLogic equations with outputs of virtual output 3 and
virtual output 4, shown as follows.

Figure 5-77: Logic example with virtual outputs

Virtual output 1
state = On
Virtual output 2
Set
state = On
Latch
OR #1 Reset
Virtual input 1
state = On Timer 2
XOR Time delay
Digital element 1 OR #2 Virtual output 4
on dropout
state = Pickup
(200 ms)

state = Operated Time delay
AND on pickup
(800 ms)
Contact input H1c
state = Closed Virtual output 3
827026A2.CDR
2. Prepare a logic diagram for the equation to produce virtual output 3, as this output is used as an operand in the virtual
output 4 equation (create the equation for every output that is used as an operand first, so that when these operands
are required they already have been evaluated and assigned to a specific virtual output). The logic for virtual output 3
is shown as follows with the final output assigned.
Figure 5-78: Logic for virtual output 3
Digital element 2 5
state= Operated
AND(2) Virtual output 3
Contact input H1c

state = Closed
827027A2.CDR
3. Prepare a logic diagram for virtual output 4, replacing the logic ahead of virtual output 3 with a symbol identified as
virtual output 3, shown as follows.
Figure 5-79: Logic for virtual output 4
Virtual output 1
state = On
Virtual output 2
Set
state = On
Latch
OR #1 Reset
Virtual input 1
state = On Timer 2
XOR Time delay
OR #2 Virtual output 4
Digital element 1 on dropout
state = Pickup
(200 ms)
Timer 1
Virtual output 3 Time delay
state = On on pickup
(800 ms)
Contact input H1c
state = Closed
827028A2.CDR
4. Program the FlexLogic equation for virtual output 3 by translating the logic into available FlexLogic parameters. The
equation is formed one parameter at a time until the required logic is complete. It is generally easier to start at the
output end of the equation and work back towards the input, as shown in the following steps. It is also recommended

to list operator inputs from bottom to top. For demonstration, the final outputs are arbitrarily identified as parameter
99, and each preceding parameter decremented by one in turn. Until accustomed to using FlexLogic, it is suggested
that a worksheet with a series of cells marked with the arbitrary parameter numbers be prepared shown as follows.
Figure 5-80: FlexLogic worksheet
01
02
03
04
05
.....
97
98
99
827029A1.VSD
5. Following the procedure outlined, start with parameter 99, as follows:

– 99: The final output of the equation is virtual output 3, which is created by the operator "= Virt Op n". This
parameter is therefore "= Virt Op 3".
5 – 98: The gate preceding the output is an AND, which in this case requires two inputs. The operator for this gate is a
2-input AND so the parameter is “AND(2)”. Note that FlexLogic rules require that the number of inputs to most
types of operators must be specified to identify the operands for the gate. As the 2-input AND operates on the
two operands preceding it, these inputs must be specified, starting with the lower.
– 97: This lower input to the AND gate must be passed through an inverter (the NOT operator) so the next
parameter is “NOT”. The NOT operator acts upon the operand immediately preceding it, so specify the inverter
input next.
– 96: The input to the NOT gate is to be contact input H1c. The ON state of a contact input can be programmed to
be set when the contact is either open or closed. Assume for this example that the state is to be ON for a closed
contact. The operand is therefore “Cont Ip H1c On”.
– 95: The last step in the procedure is to specify the upper input to the AND gate, the operated state of digital
element 2. This operand is "DIG ELEM 2 OP".
Writing the parameters in numerical order forms the equation for virtual output 3:
[95] DIG ELEM 2 OP
[96] Cont Ip H1c On
[97] NOT
[98] AND(2)
[99] = Virt Op 3
It is now possible to check that this selection of parameters produces the required logic by converting the set of
parameters into a logic diagram. The result of this process is shown in the figure, which is compared to the logic for
virtual output 3 diagram as a check.

Figure 5-81: FlexLogic equation for virtual output 3

FlexLogic entry:
95
Dig Element 2 (DE2) OP
AND Virtual output 3
FlexLogic entry:
96
Cont Ip 2 On (H1c)
FlexLogic entry:
97
NOT
FlexLogic entry:
98
AND (2)
FlexLogic entry:
99
= Virt Op 3 (VO3)
827030A2.CDR
6. Repeating the process described for virtual output 3, select the FlexLogic parameters for Virtual Output 4.
– 99: The final output of the equation is virtual output 4, which is parameter “= Virt Op 4".
– 98: The operator preceding the output is timer 2, which is operand “TIMER 2". Note that the settings required for
the timer are established in the timer programming section.
– 97: The operator preceding timer 2 is OR #2, a 3-input OR, which is parameter “OR(3)”.
– 96: The lowest input to OR #2 is operand “Cont Ip H1c On”.
– 95: The center input to OR #2 is operand “TIMER 1".
– 94: The input to timer 1 is operand “Virt Op 3 On".
– 93: The upper input to OR #2 is operand “LATCH (S,R)”.
– 92: There are two inputs to a latch, and the input immediately preceding the latch reset is OR #1, a 4-input OR,
which is parameter “OR(4)”.
– 91: The lowest input to OR #1 is operand “Virt Op 3 On".
– 90: The input just above the lowest input to OR #1 is operand “XOR(2)”. 5
– 89: The lower input to the XOR is operand “DIG ELEM 1 PKP”.
– 88: The upper input to the XOR is operand “Virt Ip 1 On".
– 87: The input just below the upper input to OR #1 is operand “Virt Op 2 On".
– 86: The upper input to OR #1 is operand “Virt Op 1 On".
– 85: The last parameter is used to set the latch, and is operand “Virt Op 4 On".
The equation for virtual output 4 is:
[85] Virt Op 4 On
[86] Virt Op 1 On
[87] Virt Op 2 On
[88] Virt Ip 1 On
[89] DIG ELEM 1 PKP
[90] XOR(2)
[91] Virt Op 3 On
[92] OR(4)
[93] LATCH (S,R)
[94] Virt Op 3 On
[95] TIMER 1
[96] Cont Ip H1c On
[97] OR(3)
[98] TIMER 2
[99] = Virt Op 4
Now check that the selection of parameters produce the required logic by converting the set of parameters into a
logic diagram. The result is shown in the figure, which is compared to the logic for virtual output 4 diagram as a check.

Figure 5-82: FlexLogic equation for virtual output 4

FlexLogic entry:
85 Virt Op 4 On (VO4)
FlexLogic entry:
FlexLogic entry:
FlexLogic entry: Set
88 Latch
Virt Ip 1 On (VI1)
XOR OR Reset
FlexLogic entry:
89 Dig Element 1 (DE1) PKP
FlexLogic entry:
90 XOR (2 Input)
FlexLogic entry:
OR T2 Virtual output 4
FlexLogic entry:
92 OR (4 Input)
FlexLogic entry:
93 Latch (Set, Reset)
FlexLogic entry:
94 Virt Op 3 On (VO3) T1
FlexLogic entry:
95 Timer 1
FlexLogic entry:
96 Cont Ip 2 On (H1c)
FlexLogic entry:
97 OR (3 Input)
FlexLogic entry:
98 Timer 2
FlexLogic entry:
99 =Virt Op 4 (VO4) 827031A2.CDR
5 7. Now write the complete FlexLogic expression required to implement the logic, making an effort to assemble the
equation in an order where Virtual Outputs that are used as inputs to operators are created before needed. In cases
where a lot of processing is required to perform logic, this can be difficult to achieve, but in most cases does not cause
problems as all logic is calculated at least four times per power frequency cycle. The possibility of a problem caused by
sequential processing emphasizes the necessity to test the performance of FlexLogic before it is placed in service.
In the following equation, virtual output 3 is used as an input to both latch 1 and timer 1 as arranged in the following
order:
DIG ELEM 2 OP
Cont Ip H1c On
NOT
AND(2)
= Virt Op 3
Virt Op 4 On
Virt Op 1 On
Virt Op 2 On
Virt Ip 1 On
DIG ELEM 1 PKP
XOR(2)
Virt Op 3 On
OR(4)
LATCH (S,R)
Virt Op 3 On
TIMER 1
Cont Ip H1c On
OR(3)
TIMER 2
= Virt Op 4
END
In this expression, the virtual output 4 input to the four-input OR is listed before it is created. This is typical of a form of
feedback, in this case, used to create a seal-in effect with the latch, and is correct.
8. Always test the logic after it is loaded into the relay, in the same way as has been used in the past. Testing can be
simplified by placing an "END" operator within the overall set of FlexLogic equations. The equations are evaluated up

to the first "END" operator.

The "On" and "Off" operands can be placed in an equation to establish a known set of conditions for test purposes, and
the "INSERT" and "DELETE" commands can be used to modify equations.
5.5.5 FlexLogic equation editor

SETTINGS  FLEXLOGIC  FLEXLOGIC EQUATION EDITOR
 FLEXLOGIC FLEXLOGIC ENTRY 1: Range: FlexLogic operands
 EQUATION EDITOR  END

FLEXLOGIC ENTRY 1024: Range: FlexLogic operands
 END
There are 1,024 FlexLogic entries available, numbered from 1 to 1024, with default END entry settings. If a "Disabled"
element is selected as a FlexLogic entry, the associated state flag is never set to ‘1’. Press the +/– key when editing
FlexLogic equations to quickly scan through the major parameter types.
5.5.6 FlexLogic timers

SETTINGS  FLEXLOGIC  FLEXLOGIC TIMERS  FLEXLOGIC TIMER 1(32)
 FLEXLOGIC TIMER 1 Range: millisecond, second, minute
 TIMER 1  TYPE: millisecond
TIMER 1 PICKUP Range: 0 to 60000 in steps of 1

 DELAY: 0
5
TIMER 1 DROPOUT Range: 0 to 60000 in steps of 1
 DELAY: 0
There are 32 identical FlexLogic timers available. These timers are used as operators for FlexLogic equations.
TIMER 1 TYPE — Selects the time measurement unit.
TIMER 1 PICKUP DELAY — Sets the time delay to pickup. If a pickup delay is not required, set this function to "0."
TIMER 1 DROPOUT DELAY — Sets the time delay to dropout. If a dropout delay is not required, set this function to "0."
5.5.7 Non-volatile latches

SETTINGS  FLEXLOGIC  NON-VOLATILE LATCHES  LATCH 1(16)
 LATCH 1 LATCH 1 Range: Disabled, Enabled
LATCH 1 ID: Range: up to 20 alphanumeric characters

 NV Latch 1
LATCH 1 TYPE: Range: Reset Dominant, Set Dominant

 Reset Dominant
LATCH 1 SET: Range: FlexLogic operand

 Off
LATCH 1 RESET: Range: FlexLogic operand

 Off
LATCH 1 Range: Self-reset, Latched, Disabled

 TARGET: Self-reset
LATCH 1 Range: Disabled, Enabled


GROUPED ELEMENTS CHAPTER 5: SETTINGS
The non-volatile latches provide a permanent logical flag that is stored safely and do not reset upon restart after the relay
is powered down. Typical applications include sustaining operator commands or permanently blocking relay functions,
such as Autorecloser, until a deliberate interface action resets the latch.
LATCH 1 TYPE — This setting characterizes Latch 1 to be Set- or Reset-dominant.
LATCH 1 SET — If asserted, the specified FlexLogic operands 'sets' Latch 1.
LATCH 1 RESET — If asserted, the specified FlexLogic operand 'resets' Latch 1.
Figure 5-83: Non-volatile latch operation table (N = 1 to 16) and logic

SETTING SETTING
LATCH 1 FUNCTION: LATCH 1 TYPE:
Enabled=1 RUN
SETTING
LATCH 1 SET:
FLEXLOGIC OPERANDS
Off=0 SET LATCH 1 ON
LATCH 1 OFF
SETTING
LATCH 1 RESET:
Off=0 RESET 842005A3.CDR
Latch n type Latch n Latch n Latch n Latch n

set reset on off
Reset ON OFF ON OFF
5 Dominant
OFF OFF Previous Previous
State State
ON ON OFF ON
OFF ON OFF ON
Set ON OFF ON OFF
Dominant
ON ON ON OFF
OFF OFF Previous Previous
State State
OFF ON OFF ON
5.6 Grouped elements

5.6.1 Overview
Each protection element can be assigned up to six sets of settings with designations 1 to 6. The performance of these
elements is defined by the active setting group at a given time. Multiple setting groups allow the user to conveniently
change protection settings for different operating situations (for example, altered power system configuration or season of
the year). The active setting group can be preset or selected in the SETTING GROUPS menu (see the Control Elements section
later in this chapter). See also the Introduction to Elements section at the beginning of this chapter.
5.6.2 Setting group 1

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)
 SETTING GROUP 1  BUS DIFFERENTIAL See below
  

CHAPTER 5: SETTINGS GROUPED ELEMENTS
 BREAKER FAILURE See page 5-162

 
 VOLTAGE ELEMENTS See page 5-170

 
 CURRENT ELEMENTS See page 5-171

 
 END FAULT PROTECTION See page 5-178

 
Each of the six setting group menus is identical. Setting group 1 (the default active group) is active automatically when no
other group is active.
If the device incorrectly switches to group 1 after power cycling, upgrade the firmware to version 7.31 or later to correct
this issue.
5.6.3 Bus differential

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  BUS DIFFERENTIAL  BUS ZONE 1(6) DIFFERENTIAL
 BUS ZONE 1 BUS ZONE 1 DIF Range: Disabled, Enabled
 DIFFERENTIAL  FUNCTION: Disabled
BUS ZONE 1 DIF Range: 0.050 to 6.000 pu in steps of 0.001

 PICKUP: 0.100 pu
BUS ZONE 1 DIF Range: 15 to 100% in steps of 1

 LOW SLOPE: 25%
 BUS ZONE 1 DIF Range: 1.00 to 30.00 pu in steps of 0.01 5

LOW BPNT: 2.00 pu
BUS ZONE 1 DIF Range: 50 to 100% in steps of 1

 HIGH SLOPE: 60%

 HIGH BPNT: 8.00 pu

 HIGH SET: 15.00 pu
BUS ZONE 1 DIF Range: 0.000 to 65.535 s in steps of 0.001

 SEAL-IN: 0.400 s
BUS ZONE 1 DIF SUPV: Range: FlexLogic operand

 On
BUS ZONE 1 DIF TRIP: Range: FlexLogic operand

 Off
BUS ZONE 1 DIF BLK: Range: FlexLogic operand

 Off
BUS ZONE 1 DIF Range: Self-reset, Latched, Disabled

 TARGET: Latched
BUS ZONE 1 DIF Range: Disabled, Enabled

Up to six zones of bus differential protection are provided, depending on the software options. The operation of these
elements is completely dependent on the dynamic bus replica, which must be defined first. Both restrained (biased) and
unrestrained (unbiased, instantaneous) bus differential protection functions are provided for each bus differential zone.
The biased bus differential function has a dual-slope operating characteristic (see figure below) operating in conjunction
with saturation detection and a directional comparison principle (see the logic diagram in this section).

Figure 5-84: Biased differential operating characteristic
|Id|
differential
OPERATE
HIGH
SLOPE
BLOCK
LOW SLOPE Ir
PICKUP
HIGH BPNT
LOW BPNT
restraining
836720A1.cdr
The protected zone input current with the highest magnitude is used as the restraining signal. Stability during heavy
external faults is achieved by dynamic CT saturation detection and current flow direction supervision without affecting
sensitivity and speed of operation for internal faults.
The differential operating characteristic is divided into two regions. In the region of low differential currents and lower
5 slope, the element operates on a 2-out-of-2 basis, applying both the differential and current directional tests. In the region
of high differential currents, the element operates on a dynamic 1-out-of-2 / 2-out-of-2 basis. If the differential current is in
this region and CT saturation is detected, both the differential and current directional tests are applied. If CT saturation is
ruled out by the saturation detector, the differential protection principle alone is capable of causing the element to
operate.
The saturation detector is an integral part of the bus differential element. It has no settings but uses some of the
differential characteristic parameters. The flags indicating CT saturation are available on a per phase basis as FlexLogic
operands.
The directional principle is an integral part of the biased bus differential element and has no associated settings. The
directional element dynamically identifies what appears to be the faulted circuit and compares its current angle with that
of the sum of the remaining currents of the protected zone. The element declares a bus fault if the angle is less than 90°.
Directional indicating flags signal operation on a per-phase basis and are available as FlexLogic operands.
The unbiased bus differential function checks the magnitude of the differential current against an adjustable threshold.
Neither the bias nor the directional principles apply. The operation of the unbiased differential function is associated with
separate output operands.
The bus differential protection feature is available only when PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION is set to
“Protection”.
Operation of this element is completely dependent on the dynamic bus replica which must be first defined under bus zone
1. The bus differential element 1 protects the differential zone defined as bus zone 1.
BUS ZONE 1 DIF PICKUP — This setting defines the minimum differential current required for operation of the biased bus
differential protection element. This setting is chosen based on the maximum magnitude of the differential current that
might be seen under no-load conditions. This setting prevents relay maloperation in the situation when the bus carries
little power and the restraining signal is too low to provide enough bias in the first slope region of the differential
characteristic.
This setting can also be set above the maximum load level to ensure security during CT trouble conditions. However,
voltage supervision or a check-zone are better alternatives.

BUS ZONE 1 DIF LOW SLOPE — This setting defines the percentage bias for the restraining currents, from zero to the lower
breakpoint (LOW BPNT). This setting determines the sensitivity of the relay for low current internal faults. The value chosen
needs to be high enough to accommodate the spurious differential current resulting from inaccuracy of the CTs operating
in their linear mode, i.e. in load conditions and during distant external faults. When adjusting this setting, it must be kept in
mind that the restraining signal used by the biased bus differential protection element is created as the maximum of all the
input currents.
BUS ZONE 1 DIF LOW BPNT — This setting defines the lower breakpoint of the dual-slope operating characteristic. The
percentage bias applied for the restraining current from zero to the value specified as LOW BPNT is given by the LOW SLOPE
setting. This setting needs to be set above the maximum load current. The LOW BPNT can be moved to the AC current
under which all the CTs are guaranteed to transform without saturation. This includes the effect of residual magnetism.
When adjusting this setting, keep in mind that the restraining signal is created as the maximum of all the input currents.
BUS ZONE 1 DIF HIGH SLOPE — This setting defines the percentage bias for the restraining currents above the higher
breakpoint (HIGH BPNT). This setting affects stability of the relay for heavy external faults. Traditionally, the value chosen for
this setting needs to be high enough to accommodate the spurious differential current resulting from saturation of the CTs
during heavy external faults. This requirement can be considerably relaxed in favor of sensitivity and speed of operation as
the relay detects CT saturation and upon detection applies the directional principle to prevent maloperation. When
adjusting this setting, keep in mind that the restraining signal is created as the maximum of all the input currents.
BUS ZONE 1 DIF HIGH BPNT — This setting defines the higher breakpoint of the dual-slope operating characteristic. The
percentage bias applied for the restraining current above the value specified as HIGH BPNT is given by the HIGH SLOPE
setting. The HIGH BPNT setting needs to be set below the minimum AC current that is likely to saturate the weakest CT
feeding the relay. When adjusting this setting, it must be kept in that mind the restraining signal is created as the
maximum of all the input currents.
The dual-slope operating characteristic of the biased bus differential protection element is shaped to ensure true
percentage bias for high restraining currents (see the following figure). This means that the straight line defining the upper
slope intersects the origin of the differential-restraining plane and a discontinuity appears between the low and high slope
regions (between the LOW BPNT and HIGH BPNT settings). This discontinuity is handled by approximating the operate/no-
5
operate boundary of the characteristic using a certain “gluing” function. This ensures smooth transition of the slope from
LOW SLOPE (lower value) to HIGH SLOPE (higher value).
The following parameters of the biased operating characteristic are used by the saturation detector: LOW SLOPE, HIGH
SLOPE, and HIGH BPNT. The saturation detector uses these settings to detect specific relations between the differential and
restraining currents. The values of these settings are selected based on the aforementioned criteria related to the art of
bus differential protection.
BUS ZONE 1 DIF HIGH SET — This setting defines the minimum differential current required for operation of the unbiased bus
differential protection function. This setting is based on the maximum magnitude of the differential current that might be
seen during heavy external faults causing deep CT saturation. When selecting this setting, keep in mind that the unbiased
bus differential protection function uses the full-cycle Fourier measuring algorithm and applies it to pre-filtered samples of
the input currents. As a result, the transient measuring errors including the effect of the DC component are below 2%.
During heavy CT saturation when the currents are significantly distorted, the magnitude of the differential current as
measured by the relay and used by the unbiased bus differential function is significantly lower than both the peak values
of the waveform and the true RMS value. The measured magnitude practically reflects the power system frequency
component alone. This allows for lower values of the HIGH SET setting.
The unbiased (high set) differential function can be virtually disabled by setting its operating threshold, HIGH SET, very high.
BUS ZONE 1 DIF SEAL-IN — This setting defines the drop-out time of the seal-in timer applied to the BUS 1 OP FlexLogic
operand.
BUS ZONE 1 DIFF SUPV — This setting specifies a FlexLogic operand that supervises operation of the element. Typical
applications include undervoltage condition and overall (check) zone. In a sense the setting is similar to the blocking input,
but does not stop the element from running. This is important for saturation detector, as the latter requires some historical
data. The Bus Differential element shall not be supervised from the blocking input. The blocking input (BUS ZONE 1 DIF BLK
setting) is meant to block the element permanently, not dynamically from a fault depended condition such as
undervoltage.
BUS ZONE 1 DIF TRIP — This setting specifies a FlexLogic operand that forces operation of the zone. Typical applications
include forced trip of the healthy phase from the faulted phase, or a trip command from the BF function to isolate the
entire zone of busbar protection.

More information on the bus zone differential settings can be found in the Application of Settings chapter.

SETTING
B90 FUNCTION:
Logic = 0
Protection = 1 SETTING
CHAPTER 5: SETTINGS
BUS ZONE 1 DIF

SETTING
HIGH SET:
BUS ZONE 1 DIF FLEXLOGIC OPERANDS
RUN
FUNCTION: BUS 1 UNBIASED OP
| ID1 | > HIGH SET
Disabled = 0
Enabled = 1
AND
SETTING
SETTING BUS ZONE 1 DIF SUPV:
SETTINGS
BUS ZONE 1 DIF SETTING
BUS ZONE 1 DIF On = 1
BLOCK: BUS ZONE 1 DIF SEAL-IN:
PICKUP:
FLEXLOGIC OPERAND
Off = 0
BUS ZONE 1 DIF SETTING 0 BUS 1 OP
AND
LOW SLOPE: tRST
SETTING BUS ZONE 1 DIF TRIP:
BUS ZONE 1 DIF
BUS 1A CT: LOW BPNT: Off = 0
OR
Current Phasor BUS ZONE 1 DIF
HIGH SLOPE:
Current Samples
BUS ZONE 1 DIF
HIGH BPNT:
SETTING
RUN
BUS 1A STATUS:
Off = 0
ID1
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

AND
differential
... FLEXLOGIC OPERAND
restraining
BUS 1 BIASED OP
OR
SETTING
BUS 1X CT:
OR
AND
Current Phasor
Current Samples
differential
IR1
FLEXLOGIC OPERANDS
Figure 5-85: Bus zone 1 differential logic
SETTING restraining BUS 1 BIASED PKP

OR
BUS 1X STATUS: BUS 1 BIASED DPO

Off = 0
DIFERENTIAL (D) AND RESTRAINING (R) CURRENTS

CURRENT FLEXLOGIC OPERANDS
DIRECTIONAL BUS 1 DIR
ELEMENT
FLEXLOGIC OPERANDS
SATURATION
BUS 1 SAT
DETECTOR
836001A3.vsd
5-161
GROUPED ELEMENTS
5
5.6.4 Breaker failure (ANSI 50BF)

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  BREAKER FAILURE 1(24)
 BREAKER FAILURE

 BREAKER FAILURE
  CURRENT SUPV 1
BF1 CURRENT SUPV Range: Disabled, Enabled

 FUNCTION: Disabled
BF1 CT: Range: Available current channels

 F1
BF1 AMP SUPV Range: 0.020 to 30.000 pu in steps of

 PICKUP: 1.050 pu 0.001
BF1 AMP HISET Range: 0.020 to 30.000 pu in steps of

 PICKUP: 1.050 pu 0.001
BF1 AMP LOSET Range: 0.020 to 30.000 pu in steps of

 PICKUP: 1.050 pu 0.001
 BREAKER FAILURE 1
 
BF1 FUNCTION: Range: Disabled, Enabled

 Disabled
BF1 INITIATE: Range: FlexLogic operand


5 Off
BF1 USE AMP SUPV: Range: Yes, No

 Yes
BF1 USE SEAL-IN: Range: Yes, No

 Yes
BF1 AMP SUPV OP A: Range: FlexLogic operand

 Off
BF1 AMP SUPV OP B: Range: FlexLogic operand

 Off
BF1 AMP SUPV OP C: Range: FlexLogic operand

 Off
BF1 USE TIMER 1: Range: Yes, No

 Yes
BF1 TIMER 1 PICKUP Range: 0.000 to 65.535 s in steps of

 DELAY: 0.000 s 0.001

 Yes

 DELAY: 0.000 s 0.001

 Yes

 DELAY: 0.000 s 0.001
BF1 BKR POS1: Range: FlexLogic operand

 Off
BF1 BKR POS2: Range: FlexLogic operand

 Off

BF1 BKR TEST ON: Range: FlexLogic operand

 Off
BF1 AMP HISET OP A: Range: FlexLogic operand

 Off
BF1 AMP HISET OP B: Range: FlexLogic operand

 Off
BF1 AMP HISET OP C: Range: FlexLogic operand

 Off
BF1 AMP LOSET OP A: Range: FlexLogic operand

 Off
BF1 AMP LOSET OP B: Range: FlexLogic operand

 Off
BF1 AMP LOSET OP C: Range: FlexLogic operand

 Off
BF1 LOSET TIME Range: 0.000 to 65.535 s in steps of 1

 DELAY: 0.000 s
BF1 TRIP DROPOUT Range: 0.000 to 65.535 s in steps of 1

 TIME DELAY: 0.000 s
BF1 RETRIP TIME Range: 0.000 to 65.535 s in steps of 1

 DELAY: 0.000 s
BF1 BLOCK: Range: FlexLogic operand

 Off
 BF1 TARGET:
Self-Reset
Range: Self-Reset, Latched, Disabled 5
BF1 EVENTS: Range: Enabled, Disabled
 Disabled
 BREAKER FAILURE
  CURRENT SUPV 2
 

 BREAKER FAILURE
  CURRENT SUPV 24
 
The breaker failure feature has two parts: breaker failure current supervision and breaker failure logic. Breaker failure
current supervision acts upon current levels and is available if the PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION setting
is “Protection.” Breaker failure logic is based on status information and is available if the PRODUCT SETUP  B90 FUNCTION 
B90 FUNCTION setting is “Logic.” The Breaker failure element requires B90 fiber optic interconnection and proper
configuration of the breaker failure and direct input/output settings. See the Application of Settings chapter for details.
5.6.4.1 Breaker failure protection

In general, breaker failure schemes expect that the breaker receiving the trip command opens within a set time. If it does
not, upstream or adjacent breakers are tripped to effectively clear the fault. This widespread tripping usually interrupts
power to a larger section of the power system than the initial trip. A higher level of security is required due to the effect on
system safety and stability.
The breaker failure scheme is intended for three-pole operation but can be used with single-pole tripping if certain
conditions are satisfied (see the note below). The operation of the breaker failure element includes three stages: initiation,
identification of a breaker failure condition, and output (or response).

The Breaker Failure can be used with single-pole tripping schemes if the HISET and LOSET current elements are set
below the lowest expected fault current and above the highest expected load current.
5.6.4.2 Stage 1: Initiation

The breaker failure scheme is initiated by a FlexLogic operand representing the protection trip signal initially sent to the
breaker. This signal does not include other breaker commands that are not indicative of a fault in the protected zone. The
initiating signal should be sealed-in if primary fault detection can reset before the fault is cleared. The seal-in is supervised
by current level, so it resets when the fault is cleared. If desired, an incomplete sequence seal-in reset can be implemented
by using the initiating operand to also initiate a FlexLogic timer set longer than any breaker failure timer, whose output
operand is selected to block the breaker failure scheme.
Breaker failure scheme can be initiated either directly or with current level supervision. It is particularly important in any
application to decide if a current-supervised initiate is to be used. The use of a current supervised initiate results in the
breaker failure element not being initiate for a breaker that has very little or no current flowing through it, which may be
the case for transformer faults or ring bus where unequal current division between ring bus circuit breakers can delay the
failed breaker clearing time until the healthy ring breaker has operated. For those situations where it is required to
maintain breaker fail coverage for fault levels below the BF1 AMP SUPV PICKUP setting, a current supervised initiate should
not be used. This feature should be used for those situations where coordinating margins can be reduced when high speed
reclosing is used. If this choice is made the current supervision pickup level must be lower than the minimum fault current
flowing through the breaker.
Immediately after scheme initiation it sends again a trip signal to the breaker (re-trip). This is intended to reduce the
possibility of widespread tripping that results from a declaration of a failed breaker.
5 5.6.4.3 Stage 2: Determination of a breaker failure condition

Improved flexibility is achieved by providing three timers or stages (Timers 1, 2, and 3) as shown in the Breaker Failure Logic
diagram. Each stage is individually enabled and asserts its individual operand.
Only a breaker auxiliary contact (fast-operating) or current supervision (if enabled) can reset Timer 1 (early stage). If Timer
1 expires, it implies that current is still flowing or the breaker (position status) is still closed; that is, the breaker failed to
open. The Timer 2 (main stage) logic is not supervised by breaker status, only by current. An output is issued if current is
detected after the Timer 2 delay interval. This stage detects the condition where a breaker opens mechanically but fails to
interrupt fault current.
The HISET and LOSET settings discriminate between the pre- and post-tripping current variation for breakers that employ
opening resistors. If the current level is between HISET and LOSET, a time delay (BF x LOSET TIME DELAY) is added. For
currents above the HISET value, the BFxx LOSET TIME DELAY timer is bypassed.
The BF x LOSET TIME DELAY is based on the time that breaker resistor limited current can flow through the circuit after the
breaker interruption time. Both current detectors provide fast operating time for small multiples of the pickup setting.
The Timer 3 (slow stage) is supervised by breaker status (auxiliary contact) and control switch status, the latter indicating if
the breaker is in/out of service. This mode is typically used during maintenance. There is no current level check for this
stage since this is associated with small currents. Timer 3 is typically set with a longer time.
5.6.4.4 Stage 3: Output

The outputs from the scheme are:
• FlexLogic operands that report on the operation of portions of the scheme
• FlexLogic operand used to re-trip the protected breaker
• FlexLogic operands that initiate tripping required to clear the faulted zone. The trip output can be sealed-in for an
adjustable period.
• Target message indicating a failed breaker has been declared
• Illumination of the face plate TRIP LED

5.6.4.5 Breaker failure settings

BF1 INITIATE — This setting selects the FlexLogic operand that initiates three-pole tripping of the breaker. Although this
scheme is designed for three-pole tripping, it can be used with single-pole tripping schemes if the HISET and LOSET current
elements are set to be sensitive to the lowest expected fault value but insensitive to the highest expected load on the
protected line.
BF1 USE AMP SUPV — If set to "Yes", the element is initiated if current flowing through the breaker is above the supervision
pickup level.
BF1 USE SEAL-IN — If set to "Yes", the element is sealed-in if current flowing through the breaker is above the supervision
pickup level.
BF1 AMP SUPV OP A through C — This setting selects the B90 Remote Inputs that represent operation of the current
supervision elements on phase A, B, or C.
BF1 USE TIMER 1 — If set to "Yes", the Early Path is operational.
BF1 TIMER 1 PICKUP DELAY — Timer 1 is set to the shortest time required for breaker auxiliary contact BKR POS1 to open, from
the time the initial trip signal is applied to the breaker trip circuit, plus a safety margin
BF1 USE TIMER 2 — If set to "Yes", the Main Path is operational.
BF1 TIMER 2 PICKUP DELAY — Timer 2 is set to the expected opening time of the breaker, plus a safety margin. This safety
margin was historically intended to allow for measuring and timing errors in the breaker failure scheme equipment. In
microprocessor relays this time is not significant. In UR relays, which use a Fourier transform, the calculated current
magnitude ramps-down to zero one power frequency cycle after the current is interrupted, and this lag should be included
in the overall margin duration, as it occurs after current interruption. The Breaker Failure Main Path Sequence diagram
shows a margin of two cycles; this interval is considered the minimum appropriate for most applications.
In bulk oil circuit breakers, the interrupting time for currents less than 25% of the interrupting rating can be significantly
longer than the normal interrupting time. 5
BF1 USE TIMER 3 — If set to "Yes", the Slow Path is operational.
BF1 TIMER 3 PICKUP DELAY — Timer 3 is set to the same interval as Timer 2, plus an increased safety margin. Because this
path is intended to operate only for low level faults, the delay can be in the order of 300 to 500 ms.
BF1 BKR POS1 — This setting selects the FlexLogic operand that represents the protected breaker early-type auxiliary switch
contact (52/a). This is normally a non-multiplied Form-A contact. The contact may even be adjusted to have the shortest
possible operating time.
BF1 BKR POS2 — This setting selects the FlexLogic operand that represents the protected breaker normal type auxiliary
switch contact (52/a). This may be a multiplied contact.
BF1 BKR TEST ON — This setting selects the FlexLogic operand that represents the breaker In-Service/Out-of-Service switch,
set to the Out-of-Service position.
BF1 LOSET TIME DELAY — This setting represents the pickup delay for current detection after opening resistor insertion.
Typically this is based on the time while the breaker resistor current can flow through the circuit after the breaker
interrupting time.
BF1 TRIP DROPOUT TIME DELAY — This setting is used to set the period of time for which the trip output is sealed-in. This timer
must be coordinated with the automatic reclosing scheme of the failed breaker, to which the breaker failure sends a cancel
reclosure signal. Reclosure of a remote breaker can also be prevented by holding a Transfer Trip signal on longer than the
"reclaim" time.
BF1 RETRIP TIME DELAY — This setting is used to set a delay before asserting the re-trip operand.
BF1 CT — This setting selects the currents that will be used in Breaker Failure scheme BF1 for current supervision (AMP
SUPV, HISET and LOSET elements).
BF1 AMP SUPV PICKUP — This setting is used to set the phase current initiation and seal-in supervision level. Generally this
setting should detect the lowest expected fault current on the protected breaker. It can be set as low as necessary (lower
than breaker resistor current or lower than load current). HISET and LOSET current supervision guarantee correct
operation.
BF1 AMP HISET PICKUP — This setting is used to set the phase current fault detection level. Generally this setting detects the
lowest expected fault current on the protected breaker, before a breaker-opening resistor is inserted.

BF1 AMP LOSET PICKUP — This setting is used to set the phase current fault detection level. Generally this setting detects the
lowest expected fault current on the protected breaker, after a breaker opening resistor is inserted approximately 90% of
resistor current).
Figure 5-86: Breaker failure current supervision logic
SETTING
B90 FUNCTION:
Protection = 1
Logic = 0
SETTING
BF 1 AMP SUPV
SETTING PICKUP:
FLEXLOGIC OPERAND
AND RUN
BF 1 CURRENT SUPV
FUNCTION: I ³ PKP BKRSUPV 1 SUP OP
Disabled = 0
Enabled = 1 SETTING
BF 1 AMP HISET
PICKUP:
FLEXLOGIC OPERAND
RUN
I ³ PKP BKRSUPV 1 HISET OP
SETTING
SETTING
5
BF 1 AMP LOSET
PICKUP: FLEXLOGIC OPERAND
BF 1 CT:
RUN
I ³ PKP BKRSUPV 2 LOSET OP
F1
836740A4.cdr

Figure 5-87: Breaker failure logic

SETTING
B90 FUNCTION:
Protection = 1
Logic = 0
SETTING
BF 1
FUNCTION:
Disabled = 0
Enabled = 1 AND
SETTING
BF 1 BLOCK:
Off = 0
SETTING
BF 1 INITIATE: SETTING
BF 1 RETRIP FLEXLOGIC OPERAND
Off = 0 TIME DELAY:
AND 0 BKRFAIL 1 RETRIP
SETTING
OR
BF 1 USE SEAL-IN:
YES = 1 / NO = 0
AND
SETTING Seal in Path

BF 1 USE AMP SUPV:
YES = 1 / NO = 0
SETTING
BF 1 AMP SUPV OP A: OR
Off = 0
BF 1 AMP SUPV OP B:
Off = 0 OR
BF 1 AMP SUPV OP C:
Off = 0
5
SETTING
BF 1 USE TIMER 1:
SETTING FLEXLOGIC OPERAND
YES = 1 / NO = 0 BF 1 TIMER1 PICKUP
DELAY: BKRFAIL 1 T1 OP
SETTING AND 0
BF 1 BKR POS1:
Off = 0
OR
SETTING
SETTING BF 1 TIMER2 PICKUP
BF 1 USE TIMER 2: DELAY:
FLEXLOGIC OPERAND
AND 0
YES = 1 / NO = 0 BKRFAIL 1 T2 OP
SETTING
BF 1 AMP HISET OP A:
Off = 0
BF 1 AMP HISET OP B: AND
Off = 0 OR
BF 1 AMP HISET OP C:
Off = 0
SETTING
BF 1 LOSET TIME
SETTING DELAY:
BF 1 AMP LOSET OP A:
0
Off = 0
BF 1 AMP LOSET OP B: AND
Off = 0 OR
SETTING
BF 1 AMP LOSET OP C:
BF 1 TRIP DROPOUT
Off = 0 FLEXLOGIC OPERAND
TIME DELAY:
OR 0 BKRFAIL 1 TRIP OP
SETTING
BF 1 USE TIMER 3:
YES = 1 / NO = 0
SETTING SETTING
BF 1 TIMER 3 PICKUP
BF 1 BKR POS2: DELAY:
AND 0 FLEXLOGIC OPERAND
Off = 0
BKRFAIL 1 T3 OP
SETTING
BF 1 BKR TEST ON:
Off = 0
836739A4.cdr

5.6.4.6 Application example

For illustration, assume the F7 current is monitored for Breaker Failure protection of a given breaker as shown.
Figure 5-88: Direct I/O sample configuration for breaker failure protection
Received as DIRECT
INPUTs 1 through 9
breaker auxiliary switches
(if used for BF) IED 4
sent as bits no.13, 14 and 15

phase A current, wired to F7 IED 1
phase B current, wired to F7 IED 2
IED 3
phase C current, wired to F7
BKR FAIL SUPV OP
BKR FAIL HISET OP
BF CT = F7 BKR FAIL LOSET OP
836759A3.CDR
The Protection IEDs 1, 2, and 3 (B90 FUNCTION set to "Protection") send the Breaker Fail current supervision flags over the
Direct I/O communications. Assume bits 13, 14, and 15 are used for this purpose as follows:
5 For IED 1:
DIRECT OUTPUT DEVICE ID: "1" (this is an originating device)
DIRECT OUT 13 OPERAND: "BKRSUPV 3 SUPV OP" (this operand drives output number 13)
DIRECT OUT 14 OPERAND: "BKRSUPV 3 HISET OP" (this operand drives output number 14)
DIRECT OUT 15 OPERAND: "BKRSUPV 3 LOSET OP" (this operand drives output number 15)
For IED 2:
For IED 3:
The above nine flags must be received at the IED 4. Assume Direct Inputs 1 through 9 are to be used for this purpose. This
is accomplished with the following settings.
For IED 4:
DIRECT INPUT 1 DEVICE: "1" (message received from IED 1)
DIRECT INPUT 1 BIT NUMBER: "13" (this is BKRSUPV 3 SUPV OP for Phase A)
DIRECT INPUT 2 BIT NUMBER: "14" (this is BKRSUPV 3 HISET OP for Phase A)
DIRECT INPUT 3 BIT NUMBER: "15" (this is BKRSUPV 3 LOSET OP for Phase A)
DIRECT INPUT 4 BIT NUMBER: "13" (this is BKRSUPV 3 SUPV OP for Phase B)
DIRECT INPUT 5 BIT NUMBER: "14" (this is BKRSUPV 3 HISET OP for Phase B)


DIRECT INPUT 6 BIT NUMBER: "15" (this is BKRSUPV 3 LOSET OP for Phase B)
DIRECT INPUT 7 BIT NUMBER: "13" (this is BKRSUPV 3 SUPV OP for Phase C)
DIRECT INPUT 8 BIT NUMBER: "14" (this is BKRSUPV 3 HISET OP for Phase C)
DIRECT INPUT 9 BIT NUMBER: "15" (this is BKRSUPV 3 LOSET OP for Phase C)
The received flags are now to be configured for in the Breaker Failure 3 logic as follows:
BF 3 AMP SUPV OP A: "Direct Input 1 On"
BF 3 AMP HISET OP A: "Direct Input 2 On"
BF 3 AMP LOSET OP A: "Direct Input 3 On"
BF 3 AMP SUPV OP B: "Direct Input 4 On"
BF 3 AMP HISET OP B: "Direct Input 5 On"
BF 3 AMP LOSET OP B: "Direct Input 6 On"
BF 3 AMP SUPV OP C: "Direct Input 7 On"
BF 3 AMP HISET OP C: "Direct Input 8 On"
BF 3 AMP LOSET OP C: "Direct Input 9 On"
The B90 current supervision elements reset in less than 0.7 of a power cycle up to the multiple of pickup of 100 (threshold
set at 0.01 of the actual fault current) as in the following figure.
Figure 5-89: Breaker failure overcurrent supervision reset time
0.8
Margin
Maximum
5
Breaker failure reset time (cycles)
Average
0.6
0.4
0.2
0
0 20 40 60 80 100 120 140
MulWLple of pickup fault current
threshold setting 836769A4.CDR
As the overcurrent supervising flags must be sent via Direct I/Os to the B90 IEDs that perform the BF functionality, an extra
delay is introduced. Consequently, the following is recommended for coordinating the BF time:
Total BF Reset Time = 0.7 of a power cycle + 0.2 of a power cycle x Direct I/O bridge count Eq. 5-3
where
0.7 of a power cycle = the reset of the BF overcurrent elements
Direct I/O bridge count = the number of "bridges" between the source and destination of the Direct I/O messages
(Direct I/O delay)
For example, in the four-IED application example shown earlier, IED 2 is two "bridges" away from IED 4; therefore, the Total
BF Reset Time is 0.7 + 2 x 0.2 = 1.1 of a power system cycle.
Total BF Reset Time = 0.7 of a power cycle + 0.2 of a power cycle x Direct I/O bridge count
= 0.7 + 2 x 0.2 = 1.1 of a power cycle Eq. 5-4

Note that a message delivery time of 0.2 of a cycle per "bridge" applies when the DIRECT I/O DATA RATE is set to 128 kbps.
The relay uses sophisticated algorithms to speed up the reset time of the breaker failure overcurrent supervision.
Caution must be paid when testing the B90 for BF reset times. In particular, the current must be interrupted in a
way resembling the actual breaker operation (zero-crossing).
5.6.5 Voltage elements
5.6.5.1 Menu
SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS
 VOLTAGE ELEMENTS  UNDERVOLTAGE 1 See below
  

 UNDERVOLTAGE 12
 
5.6.5.2 Undervoltage (ANSI 27)

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  VOLTAGE ELEMENTS  UNDERVOLTAGE 1(12)
 UNDERVOLTAGE 1 UNDERVOLTAGE 1 Range: Disabled, Enabled
UNDERVOLTAGE 1 Range: Available voltage channels


5 VT: F5
UNDERVOLTAGE 1 Range: 0.004 to 3.000 pu in steps of 0.001

UNDERVOLTAGE 1 MIN Range: 0.000 to 1.000 pu in steps of 0.001

 VOLTAGE: 0.000 pu
UNDERVOLTAGE 1 PKP Range: 0.000 to 65.535 s in steps of 0.001

 DELAY: 0.000 s
UNDERVOLTAGE 1 RST Range: 0.000 to 65.535 s in steps of 0.001

 DELAY: 0.000 s
UNDERVOLTAGE 1 BLK: Range: FlexLogic operand

 Off
UNDERVOLTAGE 1 Range: Self-Reset, Latched, Disabled

 TARGET: Self-Reset
UNDERVOLTAGE 1 Range: Enabled, Disabled

The undervoltage element supervises (low-voltage check) current based main protection (that is, differential, breaker
failure, end fault, and time overcurrent backup protection). The B90 accepts phase-to-ground or phase-to-phase voltage
input configurations. If the intention is to operate all three phases for any one phase voltage collapse, appropriate
FlexLogic operand exchanges must occur between the B90s using fiber optic communications (direct inputs and outputs).
The undervoltage element also accepts the neutral voltage (3V0) from an open-corner delta VT arrangement. In this case,
the FlexLogic output is inverted to accomplish the 3V0 overvoltage functionality.
Application of the Undervoltage element is beneficial during CT trouble conditions. A low-voltage check prevents
maloperation of the main protection until the CT trouble element (differential current alarm) operates. The CT Trouble
element is user-configurable to block selected protection functions indefinitely. Voltage supervision alone does not
guarantee security because a CT trouble may be followed by an external fault causing a low-voltage condition.

Voltage pickup is set in per-unit values. The nominal voltage as entered in the SYSTEM SETUP  AC INPUTS  VOLTAGE BANK
##  VT ## SECONDARY setting corresponds to 1 pu. The minimum voltage setting (UNDERVOLTAGE 1 MIN VOLTAGE)
specifies the minimum voltage required for element operation. This setting discriminates between undervoltage conditions
for energized and de-energized circuits. If the element is used for low-voltage supervision, set this value to 0.004.
The Undervoltage element is enabled only when PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION is set to “Protection”.
One element is available per each voltage input of the relay.
Figure 5-90: Undervoltage logic
SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
UNDERVOLTAGE 1
FUNCTION:
Disabled = 0
AND
Enabled = 1
SETTING SETTINGS SETTING

UNDERVOLTAGE 1 BLK: UNDERVOLTAGE 1 MIN UNDERVOLTAGE 1
VOLTAGE: PKP DELAY:
Off = 0
UNDERVOLTAGE 1 UNDERVOLTAGE 1
PICKUP: RST DELAY:
RUN tPKP FLEXLOGIC OPERANDS
SETTING
UNDERVOLTAGE 1 VT: | V | > MIN VOLTAGE UNDERVOLTAGE 1 OP
&
Voltage Magnitude, |V| |V| < PICKUP tRST UNDERVOLTAGE 1 DPO
UNDERVOLTAGE 1 PKP
5.6.6 Current elements 5

5.6.6.1 Menu
SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  CURRENT ELEMENTS
 CURRENT ELEMENTS  INSTANTANEOUS See page 5-176
   OVERCURRENT 1

 INSTANTANEOUS
  OVERCURRENT 24
 TIME See page 5-177

  OVERCURRENT 1

 TIME
  OVERCURRENT 24
5.6.6.2 Inverse TOC curve characteristics

The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I2t standard
curve shapes. This allows for simplified coordination with downstream devices.
Table 5-22: Overcurrent curve types
IEEE IEC GE type IAC Other
IEEE Extremely Inverse IEC Curve A (BS142) IAC Extremely Inverse I2t
IEEE Very Inverse IEC Curve B (BS142) IAC Very Inverse Definite Time
IEEE Moderately Inverse IEC Curve C (BS142) IAC Inverse
IEC Short Inverse IAC Short Inverse

A time dial multiplier setting allows selection of a multiple of the base curve shape (where the time dial multiplier = 1) with
the curve shape (CURVE) setting. Unlike the electromechanical time dial equivalent, operate times are directly proportional
to the time multiplier (TD MULTIPLIER) setting value. For example, all times for a multiplier of 10 are 10 times the multiplier 1
or base curve values. Setting the multiplier to zero results in an instantaneous response to all current levels above pickup.
Time overcurrent time calculations are made with an internal energy capacity memory variable. When this variable
indicates that the energy capacity has reached 100%, a time overcurrent element operates. If less than 100% energy
capacity is accumulated in this variable and the current falls below the dropout threshold of 97 to 98% of the pickup value,
the variable must be reduced. Two methods of this resetting operation are available: “Instantaneous” and “Timed.” The
“Instantaneous” selection is intended for applications with other relays, such as most static relays, which set the energy
capacity directly to zero when the current falls below the reset threshold. The “Timed” selection can be used where the
relay must coordinate with electromechanical relays.
IEEE curves
The IEEE time overcurrent curve shapes conform to industry standards and the IEEE C37.112-1996 curve classifications for
extremely, very, and moderately inverse curves. The IEEE curves are derived from the operate and reset time equations.
Eq. 5-5
where
T = operate time (in seconds)
TDM = Multiplier setting
5 I = input current
Ipickup = Pickup Current setting
A, B, p = constants defined in the table
TRESET = reset time in seconds (assuming energy capacity is 100% and RESET is “Timed”)
tr = characteristic constant defined in the table
Table 5-23: IEEE inverse time curve constants
IEEE curve shape A B p tr
IEEE Extremely Inverse 28.2 0.1217 2.0000 29.1
IEEE Very Inverse 19.61 0.491 2.0000 21.6
IEEE Moderately Inverse 0.0515 0.1140 0.02000 4.85
Table 5-24: IEEE curve trip times (in seconds)

Multiplier Current ( I / Ipickup)
(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IEEE Extremely Inverse
0.5 11.341 4.761 1.823 1.001 0.648 0.464 0.355 0.285 0.237 0.203
1.0 22.682 9.522 3.647 2.002 1.297 0.927 0.709 0.569 0.474 0.407
2.0 45.363 19.043 7.293 4.003 2.593 1.855 1.418 1.139 0.948 0.813
4.0 90.727 38.087 14.587 8.007 5.187 3.710 2.837 2.277 1.897 1.626
6.0 136.090 57.130 21.880 12.010 7.780 5.564 4.255 3.416 2.845 2.439
8.0 181.454 76.174 29.174 16.014 10.374 7.419 5.674 4.555 3.794 3.252
10.0 226.817 95.217 36.467 20.017 12.967 9.274 7.092 5.693 4.742 4.065
IEEE Very Inverse
0.5 8.090 3.514 1.471 0.899 0.654 0.526 0.450 0.401 0.368 0.345
1.0 16.179 7.028 2.942 1.798 1.308 1.051 0.900 0.802 0.736 0.689
2.0 32.358 14.055 5.885 3.597 2.616 2.103 1.799 1.605 1.472 1.378


(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
4.0 64.716 28.111 11.769 7.193 5.232 4.205 3.598 3.209 2.945 2.756
6.0 97.074 42.166 17.654 10.790 7.849 6.308 5.397 4.814 4.417 4.134
8.0 129.432 56.221 23.538 14.387 10.465 8.410 7.196 6.418 5.889 5.513
10.0 161.790 70.277 29.423 17.983 13.081 10.513 8.995 8.023 7.361 6.891
IEEE Moderately Inverse
0.5 3.220 1.902 1.216 0.973 0.844 0.763 0.706 0.663 0.630 0.603
1.0 6.439 3.803 2.432 1.946 1.688 1.526 1.412 1.327 1.260 1.207
2.0 12.878 7.606 4.864 3.892 3.377 3.051 2.823 2.653 2.521 2.414
4.0 25.756 15.213 9.729 7.783 6.753 6.102 5.647 5.307 5.041 4.827
6.0 38.634 22.819 14.593 11.675 10.130 9.153 8.470 7.960 7.562 7.241
8.0 51.512 30.426 19.458 15.567 13.507 12.204 11.294 10.614 10.083 9.654
10.0 64.390 38.032 24.322 19.458 16.883 15.255 14.117 13.267 12.604 12.068
IEC curves
For European applications, the relay offers three standard curves defined in IEC 255-4 and British standard BS142. These
are defined as IEC Curve A, IEC Curve B, and IEC Curve C. The IEC curves are derived by the operate and reset time
equations.
Eq. 5-6
5
where
I = input current
K, E = constants defined in the table
Table 5-25: IEC (BS) inverse time curve constants
IEC (BS) curve shape K E tr
IEC Curve A (BS142) 0.140 0.020 9.7
IEC Curve B (BS142) 13.500 1.000 43.2
IEC Curve C (BS142) 80.000 2.000 58.2
IEC Short Inverse 0.050 0.040 0.500
Table 5-26: IEC curve trip times (in seconds)

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IEC Curve A
0.05 0.860 0.501 0.315 0.249 0.214 0.192 0.176 0.165 0.156 0.149
0.10 1.719 1.003 0.630 0.498 0.428 0.384 0.353 0.330 0.312 0.297
0.20 3.439 2.006 1.260 0.996 0.856 0.767 0.706 0.659 0.623 0.594
0.40 6.878 4.012 2.521 1.992 1.712 1.535 1.411 1.319 1.247 1.188
0.60 10.317 6.017 3.781 2.988 2.568 2.302 2.117 1.978 1.870 1.782
0.80 13.755 8.023 5.042 3.984 3.424 3.070 2.822 2.637 2.493 2.376


(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
1.00 17.194 10.029 6.302 4.980 4.280 3.837 3.528 3.297 3.116 2.971
IEC Curve B
0.05 1.350 0.675 0.338 0.225 0.169 0.135 0.113 0.096 0.084 0.075
0.10 2.700 1.350 0.675 0.450 0.338 0.270 0.225 0.193 0.169 0.150
0.20 5.400 2.700 1.350 0.900 0.675 0.540 0.450 0.386 0.338 0.300
0.40 10.800 5.400 2.700 1.800 1.350 1.080 0.900 0.771 0.675 0.600
0.60 16.200 8.100 4.050 2.700 2.025 1.620 1.350 1.157 1.013 0.900
0.80 21.600 10.800 5.400 3.600 2.700 2.160 1.800 1.543 1.350 1.200
1.00 27.000 13.500 6.750 4.500 3.375 2.700 2.250 1.929 1.688 1.500
IEC Curve C
0.05 3.200 1.333 0.500 0.267 0.167 0.114 0.083 0.063 0.050 0.040
0.10 6.400 2.667 1.000 0.533 0.333 0.229 0.167 0.127 0.100 0.081
0.20 12.800 5.333 2.000 1.067 0.667 0.457 0.333 0.254 0.200 0.162
0.40 25.600 10.667 4.000 2.133 1.333 0.914 0.667 0.508 0.400 0.323
0.60 38.400 16.000 6.000 3.200 2.000 1.371 1.000 0.762 0.600 0.485
0.80 51.200 21.333 8.000 4.267 2.667 1.829 1.333 1.016 0.800 0.646
1.00 64.000 26.667 10.000 5.333 3.333 2.286 1.667 1.270 1.000 0.808
IEC Short Inverse
0.05 0.153 0.089 0.056 0.044 0.038 0.034 0.031 0.029 0.027 0.026
5 0.10
0.20
0.306
0.612
0.178
0.356
0.111
0.223
0.088
0.175
0.075
0.150
0.067
0.135
0.062
0.124
0.058
0.115
0.054
0.109
0.052
0.104
0.40 1.223 0.711 0.445 0.351 0.301 0.269 0.247 0.231 0.218 0.207
0.60 1.835 1.067 0.668 0.526 0.451 0.404 0.371 0.346 0.327 0.311
0.80 2.446 1.423 0.890 0.702 0.602 0.538 0.494 0.461 0.435 0.415
1.00 3.058 1.778 1.113 0.877 0.752 0.673 0.618 0.576 0.544 0.518
IAC curves
The curves for the General Electric type IAC relay family are derived from the formulae:
Eq. 5-7
where
I = Input current
Ipkp = Pickup Current setting
A to E = constants defined in the table
Table 5-27: GE type IAC inverse time curve constants
IAC curve shape A B C D E tr
IAC Extreme Inverse 0.0040 0.6379 0.6200 1.7872 0.2461 6.008
IAC Very Inverse 0.0900 0.7955 0.1000 –1.2885 7.9586 4.678
IAC Inverse 0.2078 0.8630 0.8000 –0.4180 0.1947 0.990

IAC curve shape A B C D E tr

IAC Short Inverse 0.0428 0.0609 0.6200 –0.0010 0.0221 0.222
Table 5-28: GE type IAC curve trip times

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
IAC Extremely Inverse
0.5 1.699 0.749 0.303 0.178 0.123 0.093 0.074 0.062 0.053 0.046
1.0 3.398 1.498 0.606 0.356 0.246 0.186 0.149 0.124 0.106 0.093
2.0 6.796 2.997 1.212 0.711 0.491 0.372 0.298 0.248 0.212 0.185
4.0 13.591 5.993 2.423 1.422 0.983 0.744 0.595 0.495 0.424 0.370
6.0 20.387 8.990 3.635 2.133 1.474 1.115 0.893 0.743 0.636 0.556
8.0 27.183 11.987 4.846 2.844 1.966 1.487 1.191 0.991 0.848 0.741
10.0 33.979 14.983 6.058 3.555 2.457 1.859 1.488 1.239 1.060 0.926
IAC Very Inverse
0.5 1.451 0.656 0.269 0.172 0.133 0.113 0.101 0.093 0.087 0.083
1.0 2.901 1.312 0.537 0.343 0.266 0.227 0.202 0.186 0.174 0.165
2.0 5.802 2.624 1.075 0.687 0.533 0.453 0.405 0.372 0.349 0.331
4.0 11.605 5.248 2.150 1.374 1.065 0.906 0.810 0.745 0.698 0.662
6.0 17.407 7.872 3.225 2.061 1.598 1.359 1.215 1.117 1.046 0.992
8.0 23.209 10.497 4.299 2.747 2.131 1.813 1.620 1.490 1.395 1.323
10.0
IAC Inverse
29.012 13.121 5.374 3.434 2.663 2.266 2.025 1.862 1.744 1.654
5
0.5 0.578 0.375 0.266 0.221 0.196 0.180 0.168 0.160 0.154 0.148
1.0 1.155 0.749 0.532 0.443 0.392 0.360 0.337 0.320 0.307 0.297
2.0 2.310 1.499 1.064 0.885 0.784 0.719 0.674 0.640 0.614 0.594
4.0 4.621 2.997 2.128 1.770 1.569 1.439 1.348 1.280 1.229 1.188
6.0 6.931 4.496 3.192 2.656 2.353 2.158 2.022 1.921 1.843 1.781
8.0 9.242 5.995 4.256 3.541 3.138 2.878 2.695 2.561 2.457 2.375
10.0 11.552 7.494 5.320 4.426 3.922 3.597 3.369 3.201 3.072 2.969
IAC Short Inverse
0.5 0.072 0.047 0.035 0.031 0.028 0.027 0.026 0.026 0.025 0.025
1.0 0.143 0.095 0.070 0.061 0.057 0.054 0.052 0.051 0.050 0.049
2.0 0.286 0.190 0.140 0.123 0.114 0.108 0.105 0.102 0.100 0.099
4.0 0.573 0.379 0.279 0.245 0.228 0.217 0.210 0.204 0.200 0.197
6.0 0.859 0.569 0.419 0.368 0.341 0.325 0.314 0.307 0.301 0.296
8.0 1.145 0.759 0.559 0.490 0.455 0.434 0.419 0.409 0.401 0.394
10.0 1.431 0.948 0.699 0.613 0.569 0.542 0.524 0.511 0.501 0.493
I2t curves
The I2t curves are derived as follows:
Eq. 5-8
where

T = Operate time (in seconds)

I = Input current
Table 5-29: I2t curve trip times

(TDM)
1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
0.01 0.44 0.25 0.11 0.06 0.04 0.03 0.02 0.02 0.01 0.01
0.10 4.44 2.50 1.11 0.63 0.40 0.28 0.20 0.16 0.12 0.10
1.00 44.44 25.00 11.11 6.25 4.00 2.78 2.04 1.56 1.23 1.00
10.00 444.44 250.00 111.11 62.50 40.00 27.78 20.41 15.63 12.35 10.00
100.00 4444.4 2500.0 1111.1 625.00 400.00 277.78 204.08 156.25 123.46 100.00
600.00 26666.7 15000.0 6666.7 3750.0 2400.0 1666.7 1224.5 937.50 740.74 600.00
Definite time curve

The Definite Time curve shape operates as soon as the pickup level is exceeded for a specified period of time. The base
definite time curve delay is in seconds. The curve multiplier of 0.00 to 600.00 makes this delay adjustable from
instantaneous to 600.00 seconds in steps of 10 ms. The definite time curve shapes are defined as follows:
Eq. 5-9
5 Eq. 5-10
where
T = Operate Time (in seconds)
I = Input Current
TRESET = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed)
5.6.6.3 Instantaneous overcurrent (ANSI 50)

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  CURRENT ELEMENTS  INSTANTANEOUS
OVERCURRENT 1(24)
 INSTANTANEOUS IOC1 FUNCTION: Range: Disabled, Enabled
 OVERCURRENT 1  Disabled
IOC1 CT: Range: Available current channels

 F1
IOC1 PICKUP: Range: 0.005 to 30.000 pu in steps of 0.001

 1.200 pu
IOC1 PICKUP DELAY: Range: 0.000 to 65.535 s in steps of 0.001

 0.000 s
IOC1 RESET DELAY: Range: 0.000 to 65.535 s in steps of 0.001

 0.000 s
IOC1 BLOCK: Range: FlexLogic operand

 Off
IOC1 TARGET: Range: Self-Reset, Latched, Disabled

 Self-Reset

IOC1 EVENTS: Range: Disabled, Enabled

 Disabled
The instantaneous overcurrent element is used primarily for supervising main protection trip commands on a per-breaker
basis (that is, differential, breaker failure, and end fault protection). It responds to a single-phase current. If the intention is
to allow three-phase tripping if any phase current is above the threshold, the appropriate FlexLogic operands are passed
between the IEDs using the B90 fiber optic communications (Direct I/Os).
Instantaneous Overcurrent supervision can also be used to prevent tripping feeders with low currents or for definite time
backup protection.
The pickup setting is specified in per unit values. The nominal current as entered under SYSTEM SETUP  AC INPUTS 
CURRENT BANK XY  CT XY SECONDARY is 1 p.u. The element can be effectively enabled only when B90 FUNCTION is set to
"Protection". One instantaneous overcurrent element is available per each CT input of the relay.
Figure 5-91: Instantaneous overcurrent logic
SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
IOC 1 FUNCTION:
Disabled = 0
AND
Enabled = 1
SETTING SETTINGS
IOC 1 BLOCK: IOC 1 PICKUP DELAY:
SETTING
Off = 0
IOC 1 PICKUP: IOC 1 RESET DELAY:
IOC 1 CT:
SETTING
RUN tPKP FLEXLOGIC OPERANDS
IOC 1 OP
5
Current Magnitude, |I| | I | > PICKUP tRST IOC 1 DPO
IOC 1 PKP
5.6.6.4 Time overcurrent (ANSI 51)

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  CURRENT ELEMENTS  TIME OVERCURRENT 1(24)
 TIME TOC1 FUNCTION: Range: Disabled, Enabled
 OVERCURRENT 1  Disabled
TOC1 CT: Range: Available current channels

 F1
TOC1 PICKUP: Range: 0.020 to 30.000 pu in steps of 0.001

 1.200 pu
TOC1 CURVE: Range: see OVERCURRENT CURVE TYPES table

 IEEE Mod Inv
TOC1 TD MULTIPLIER: Range: 0.00 to 600.00 in steps of 1

 1.00
TOC1 RESET: Range: Instantaneous, Timed

 Instantaneous
TOC1 BLOCK: Range: FlexLogic operand

 Off
TOC1 TARGET: Range: Self-Reset, Latched, Disabled

 Self-Reset
TOC1 EVENTS: Range: Disabled, Enabled

 Disabled

The Time Overcurrent (TOC) element is provided for backup protection with a choice of inverse time curves. The element is
enabled only when PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION is set to "Protection". One TOC element is available per
each CT input.
Figure 5-92: Time overcurrent logic
SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
TOC 1 FUNCTION:
SETTINGS
Disabled = 0
AND
TOC 1 PICKUP:
Enabled = 1
TOC 1 CURVE:
SETTING
TOC 1 BLOCK: TOC 1 TD MULTIPLIER:
Off = 0
TOC 1 RESET: FLEXLOGIC OPERANDS
RUN |I| > PICKUP TOC 1 PKP
SETTING
TOC 1 CT: TOC 1 DPO
Current Magnitude, |I| TOC 1 OP
836006A1.vsd
5.6.7 End fault protection

SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  END FAULT PROTECTION 1(24)
5  END FAULT
 PROTECTION 1  EFP1 FUNCTION:
Disabled
EFP1 CT: Range: Available current channels

 F1
EFP1 PICKUP: Range: 0.020 to 30.000 pu in steps of 0.001

 1.200 pu
EFP1 BREAKER OPEN: Range: FlexLogic operand

 Off
EFP1 BKR DELAY: Range: 0.000 to 65.535 s in steps of 0.001

 0.400 s
EFP1 MANUAL CLOSE: Range: FlexLogic operand

 Off
EFP1 PICKUP DELAY: Range: 0.000 to 65.535 s in steps of 0.001

 0.040 s
EFP1 BLOCK: Range: FlexLogic operand

 Off
EFP1 TARGET: Range: Self-reset, Latched, Disabled

 Self-reset
EFP1 EVENTS: Range: Disabled, Enabled

 Disabled
The End Fault Protection (EFP) element operates for dead-zone faults; i.e., faults between the CT and an open feeder
breaker. Since a bus protection zone terminates on the CTs, faults between the CT and breaker require special
consideration.
With a bus-side CT (Part A of the figure below), a fault between the open CB and CT is outside the bus zone but can only
cleared by tripping the bus zone protection. In this case EFP trips the bus zone protection once the current exceeds a user-
programmable threshold, effectively clearing the fault.

With a line-side CT (Part B of the figure below), the zone is reduced once the breaker opens. Otherwise, the bus protection
may issue an unnecessary widespread trip in the case of a fault between the open CB and CT. The zone is shortened using
the breaker position with a short drop-out delay as a connection status for the associated current. Once the bus zone
moves and terminates on the CB, a dead-zone is created between the CB and CT. In this case, the EFP is used; upon
operation, the EFP will trip the remote breaker.
The EFP element arms when the feeder breaker opens and resets when a manual breaker CLOSE command is issued. To
avoid race conditions, a user-programmable time delay for the breaker OPEN signal is provided. Once armed, the element
operates when the current exceeds a user-programmable threshold. The output must be configured to either send an
inter-trip or trip the bus zone protection depending on the CT orientation with respect to the breaker.
Figure 5-93: Application of end fault protection element
(a) (b)
BUS ZONE BUS ZONE
"dead-zone" "dead-zone"
(requires tripping (requires inter-
the bus) tripping)
836745A1.vsd
5
EFP1 PICKUP — Specifies the current level recognized by an armed EFP scheme as fault current in the protected dead-zone.
Although it can be set very low (above the noise level), set above the maximum load current for extra security.
EFP1 BREAKER OPEN — This setting is a FlexLogic operand indicating an open breaker. The operand shall be "On" when the
breaker is open. Typically, this setting is a position of an appropriately wired input contact of the B90.
EFP1 BKR DELAY — This setting specifies a timed delay between the breaker position being declared as open by the EFP1
BREAKER OPEN setting and the moment the EFP scheme is armed. Set this delay long enough to avoid spurious operation
due to a delay between the breaker position and decaying of the breaker current. The current ramp down period of the
B90 for the purpose of setting the EFP is 1.3 of a power system cycle.
EFP1 MANUAL CLOSE — This setting is a FlexLogic operand indicating a close command for the breaker. This operand shall
be "On" when the breaker is ordered to close. Typically this setting is a position of an appropriately wired input contact of
the B90.
EFP1 PICKUP DELAY — This setting allows extra security when tripping the bus from the EFP element. This timer shall be set
longer than the maximum delay between the breaker closing and picking up some current and the EFP MANUAL CLOSE
signal. If the manual close signal, EFP MANUAL CLOSE, arrives before the timer expires, the element resets and misoperation
due to signal transit times is avoided.
EFP1 BLOCK — This setting dynamically block/unblocks the element. A typical application is a by-pass isolator as shown
below. When the isolator is closed, the current does not necessarily indicate on a fault between the CB and CT and the
element shall be blocked. Therefore, the close status of the isolator shall be used as the block setting.

CONTROL ELEMENTS CHAPTER 5: SETTINGS
Figure 5-94: End fault protection and bypass isolators

BUS SECTION
TRANSFER BUS
CB ISO
selective
"dead-zone"
only if the isolator is
open
836746A1.vsd
Figure 5-95: End fault protection logic

SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
5 EFP 1 FUNCTION:
Disabled = 0
AND
Enabled = 1
SETTING
EFP 1 BLOCK:
SETTING
Off = 0
EFP 1 PICKUP:
RUN
SETTING
EFP 1 CT:
Current Magnitude, |I| | I | > PICKUP
SETTING
SETTING EFP 1 PICKUP DELAY:
EFP 1 MANUAL CLOSE: FLEXLOGIC OPERANDS
tPKP
AND
Off = 0 EFP 1 OP
0
SETTINGS EFP 1 DPO
SETTING EFP 1 BRK DELAY: EFP PKP
EFP 1 BREAKER OPEN:
tPKP
Off = 0
0
836004A1.vsd
5.7 Control elements

5.7.1 Overview
Control elements are used for control rather than protection. See the Introduction to Elements section at the beginning of
this chapter for information.

CHAPTER 5: SETTINGS CONTROL ELEMENTS
5.7.2 Trip bus

SETTINGS  CONTROL ELEMENTS  TRIP BUS  TRIP BUS 1(6)
 TRIP BUS 1 TRIP BUS 1 Range: Enabled, Disabled
TRIP BUS 1 BLOCK: Range: FlexLogic operand

 Off
TRIP BUS 1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01

 DELAY: 0.00 s
TRIP BUS 1 RESET Range: 0.00 to 600.00 s in steps of 0.01

 DELAY: 0.00 s
TRIP BUS 1 INPUT 1: Range: FlexLogic operand

 Off

TRIP BUS 1 INPUT 16: Range: FlexLogic operand
 Off
TRIP BUS 1 Range: Enabled, Disabled

 LATCHING: Disabled
TRIP BUS 1 RESET: Range: FlexLogic operand

 Off
TRIP BUS 1: Range: Self-reset, Latched, Disabled

 TRIP BUS 1
EVENTS: Disabled
5
The trip bus element allows aggregating outputs of protection and control elements without using FlexLogic and assigning
them a simple and effective manner. Each trip bus can be assigned for either trip or alarm actions. Simple trip conditioning
such as latch, delay, and seal-in delay are available.
The easiest way to assign element outputs to a trip bus is through the EnerVista software under Settings > Protection
Summary. Navigate to a specific protection or control protection element and check the bus box by hovering over the
blank check box and selecting an option that displays. Once the required element is selected for a specific bus, a list of
element operate-type operands are displayed and can be assigned to a trip bus. If more than one operate-type operand is
required, it can be assigned directly from the trip bus menu.

Figure 5-96: Trip bus fields in the protection summary
The following settings are available.

TRIP BUS 1 BLOCK — The trip bus output is blocked when the operand assigned to this setting is asserted.
TRIP BUS 1 PICKUP DELAY — This setting specifies a time delay to produce an output depending on how output is used.
TRIP BUS 1 RESET DELAY — This setting specifies a time delay to reset an output command. Set the time delay long enough
5 to allow the breaker or contactor to perform a required action.
TRIP BUS 1 INPUT 1 to TRIP BUS 1 INPUT 16 — These settings select a FlexLogic operand to be assigned as an input to the trip
bus.
TRIP BUS 1 LATCHING — This setting enables or disables latching of the trip bus output. This is typically used when lockout is
required or user acknowledgement of the relay response is required.
TRIP BUS 1 RESET — The trip bus output is reset when the operand assigned to this setting is asserted. Note that the RESET OP
operand is pre-wired to the reset gate of the latch, As such, a reset command from the front panel interface or via
communications resets the trip bus output.

Figure 5-97: Trip bus logic

SETTINGS
TRIP BUS 1 INPUT 1
SETTINGS
= Off
TRIP BUS 1 PICKUP
TRIP BUS 1 INPUT 2
DELAY
= Off Non-volatile,
TRIP BUS 1 RESET
*** OR set-dominant
DELAY
AND S TPKP FLEXLOGIC OPERAND
TRIP BUS 1 INPUT 16 TRIP BUS 1 OP
Latch
= Off TRST
R
SETTINGS
TRIP BUS 1 FLEXLOGIC OPERAND
FUNCTION
TRIP BUS 1 PKP
= Enabled
TRIP BUS 1 BLOCK AND
= Off
SETTINGS
TRIP BUS 1
LATCHING
= Enabled
TRIP BUS 1 RESET
= Off
OR
FLEXLOGIC OPERAND
RESET OP 842023A1.CDR
5.7.3 Setting groups 5

SETTINGS  CONTROL ELEMENTS  SETTING GROUPS
 SETTING GROUPS SETTING GROUPS Range: Disabled, Enabled
  FUNCTION: Enabled
SETTING GROUPS BLK: Range: FlexLogic operand

 Off
GROUP 2 ACTIVATE ON: Range: FlexLogic operand

 Off

GROUP 6 ACTIVATE ON: Range: FlexLogic operand
 Off
GROUP 1 NAME: Range: up to 16 alphanumeric characters



GROUP 6 NAME: Range: up to 16 alphanumeric characters

SETTING GROUP Range: Disabled, Enabled
The setting groups menu controls the activation and deactivation of up to six possible groups of settings in the GROUPED
ELEMENTS settings menu. The active setting group can be indicated on the front display of the UR by configuring User-
Programmable LEDs to display the state of the SETTING GROUP ACT FlexLogic operands.
SETTING GROUPS FUNCTION — When Enabled, allows setting groups other than group 1 (the default active group) to be
activated. The default setting group is forced active while the SETTING GROUPS FUNCTION setting is Disabled.
SETTING GROUPS BLK — Prevents the active setting group from changing when the selected FlexLogic operand is "On." This
can be useful in applications where it is undesirable to change the settings under certain conditions, such as during a
control sequence.

GROUP 2 ACTIVATE ON to GROUP 6 ACTIVATE ON — Selects a FlexLogic operand which, when set, makes the particular setting
group active for use by any grouped element. A priority scheme ensures that only one group is active at a given time — the
highest-numbered group that is activated by its ACTIVATE ON parameter takes priority over the lower-numbered groups.
There is no activate on setting for group 1 (the default active group), because group 1 automatically becomes active if no
other group is active.
SETTING GROUP 1 NAME to SETTING GROUP 6 NAME — Allows the user to assign a name to each of the six settings groups.
Once programmed, this name appears on the second line of the GROUPED ELEMENTS  SETTING GROUP 1(6) menu display.
A setting group selection can also be made by the IEC 61850 MMS service SelectActiveSG to the control block @Master/
LLN0.SGCB. The priority scheme mentioned makes active the highest numbered group selected by SelectActiveSG or the
GROUP ACTIVATE ON settings. The SelectActiveSG selection has a default value of 1, so until a higher SelectActiveSG
selection is received, the GROUP ACTIVATE ON settings control the active group.
The most recent SelectActiveSG selection is preserved while the UR is powered down or reset.
If it becomes necessary to cancel the SelectActiveSG selection without using a SelectActiveSG service request, change the
SETTING GROUPS FUNCTION setting to Disabled. This resets the SelectActiveSG selection to 1.
5.7.4 Digital elements

SETTINGS  CONTROL ELEMENTS  DIGITAL ELEMENTS  DIGITAL ELEMENT 1(48)
 DIGITAL ELEMENT 1 DIGITAL ELEMENT 1 Range: Disabled, Enabled
DIG ELEM 1 NAME: Range: up to 16 alphanumeric characters

 Dig Element 1
5  DIG ELEM 1 INPUT:

Off
Range: FlexLogic operand
DIG ELEM 1 PICKUP Range: 0.000 to 999999.999 s in steps of 0.001

 DELAY: 0.000 s
DIG ELEM 1 RESET Range: 0.000 to 999999.999 s in steps of 0.001

 DELAY: 0.000 s
DIGITAL ELEMENT 1 Range: Disabled, Enabled

 PICKUP LED: Enabled
DIG ELEM 1 BLOCK: Range: FlexLogic operand

 Off
DIGITAL ELEMENT 1 Range: Self-reset, Latched, Disabled

DIGITAL ELEMENT 1 Range: Disabled, Enabled

Digital elements run once per power system cycle.

As such they can easily fail to react to an input signal or a block signal with a duration less than one power system
cycle. This also means that digital element output can react up to one power system cycle later than the pickup
and reset delay settings indicate.
Do not use digital elements with transient signals, such as communications commands. Do not use digital
elements where random delays of up to one cycle cannot be tolerated, such as in high speed protection.
There are 48 identical digital elements available, numbered 1 to 48. A digital element can monitor any FlexLogic operand
and present a target message and/or enable events recording depending on the output operand state. The digital element
settings include a name to be referenced in any target message, a blocking input from any selected FlexLogic operand,
and a timer for pickup and reset delays for the output operand.
DIGITAL ELEMENT 1 INPUT — Selects a FlexLogic operand to be monitored by the digital element.

DIGITAL ELEMENT 1 PICKUP DELAY — Sets the required time delay from element pickup to element operation. If a pickup delay
is not required, set to "0," To avoid nuisance alarms, set the delay greater than the operating time of the breaker.
DIGITAL ELEMENT 1 RESET DELAY — Sets the time delay to reset. If a reset delay is not required, set to “0.”
DIGITAL ELEMENT 1 PICKUP LED — This setting enables or disabled the digital element pickup LED. When set to “Disabled,” the
operation of the pickup LED is blocked.
Figure 5-98: Digital element logic
SETTING
DIGITAL ELEMENT 01
FUNCTION: SETTINGS
Enabled = 1 DIGITAL ELEMENT 01
SETTING PICKUP DELAY:
DIGITAL ELEMENT 01 DIGITAL ELEMENT 01 FLEXLOGIC OPERANDS
SETTING
NAME: RESET DELAY:
DIGITAL ELEMENT 01 DIG ELEM 01 DPO
AND RUN tPKP
INPUT: DIG ELEM 01 PKP
Off = 0 DIG ELEM 01 OP
INPUT = 1 tRST
SETTING
DIGITAL ELEMENT 01
BLOCK:
Off = 0 827042A2.VSD
Circuit monitoring applications

Some versions of the digital input modules include an active voltage monitor circuit connected across form-A contacts.
The voltage monitor circuit limits the trickle current through the output circuit (see technical specifications for form-A).
As long as the current through the voltage monitor is above a threshold (see technical specifications for form-A), the Cont
5
Op 1 VOn FlexLogic operand is set (for contact input 1—corresponding operands exist for each contact output). If the output
circuit has a high resistance or the DC current is interrupted, the trickle current drops below the threshold and the Cont Op 1
VOff FlexLogic operand is set. Consequently, the state of these operands can be used as indicators of the integrity of the
circuits in which form-A contacts are inserted.
Example 1: Breaker trip circuit integrity monitoring

In many applications it is desired to monitor the breaker trip circuit integrity so that problems can be detected before a trip
operation is required. The circuit is considered to be healthy when the voltage monitor connected across the trip output
contact detects a low level of current, well below the operating current of the breaker trip coil. If the circuit presents a high
resistance, the trickle current falls below the monitor threshold, and an alarm is declared.
In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact that is open when the
breaker is open (see figure). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must include the
breaker position.

Figure 5-99: Trip circuit example 1

UR-series device
with form-A contacts
H1a
I
H1b DC–
V DC+
H1c 52a Trip coil
I = current monitor
V = voltage monitor 827073A2.CDR
Assume the output contact H1 is a trip contact. Using the contact output settings, this output is given an ID name; for
example, “Cont Op 1." Assume a 52a breaker auxiliary contact is connected to contact input H7a to monitor breaker status.
Using the contact input settings, this input is given an ID name, for example, “Cont Ip 1," and is set “On” when the breaker is
closed. The settings to use digital element 1 to monitor the breaker trip circuit are indicated (EnerVista example shown).

Example 2: Breaker trip circuit integrity monitoring

If it is required to monitor the trip circuit continuously, independent of the breaker position (open or closed), a method to
maintain the monitoring current flow through the trip circuit when the breaker is open must be provided (as shown in the
following figure). This can be achieved by connecting a suitable resistor (see figure) across the auxiliary contact in the trip
circuit. In this case, it is not required to supervise the monitoring circuit with the breaker position – the BLOCK setting is
selected to “Off.” In this case, the settings are as follows (EnerVista example shown).
Figure 5-100: Trip circuit example 2

UR-series device
5
with form-A contacts
Values for resistor “R”

H1a
Power supply Resistance Power
I
24 V DC 1000 O 2W
H1b DC– 30 V DC 5000 O 2W
48 V DC 10000 O 2W
V DC+
110 V DC 25000 O 5W
H1c 52a Trip coil
125 V DC 25000 O 5W
R
250 V DC 50000 O 5W
Bypass
I = current monitor resistor
V = voltage monitor 827074A3.CDR
The wiring connection for two examples above is applicable to both form-A contacts with voltage monitoring and
solid-state contact with voltage monitoring.
5.7.5 Monitoring elements
5.7.5.1 Menu
SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS
 MONITORING  CT TROUBLE ZONE 1 See below
 ELEMENTS  

 CT TROUBLE ZONE 6
 

 BUS REPLICA See page 5-189

 
5.7.5.2 CT trouble zone (ANSI 50/74)

SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  CT TROUBLE ZONE 1(6)
 CT TROUBLE ZONE 1 CT TROUBLE ZONE 1 Range: Disabled, Enabled
CT TROUBLE ZONE 1 Range: 0.020 to 2.000 pu in steps of 0.001

CT TROUBLE ZONE 1 Range: 1.0 to 60.0 s in steps of 0.1

 DELAY: 1.0 s
CT TROUBLE ZONE 1 Range: Self-reset, Latched, Disabled

CT TROUBLE ZONE 1 Range: Disabled, Enabled

The CT Trouble feature is available only when PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION is set to "Protection".
This element uses the differential current calculated in accordance with the bus configuration programmed under Bus
Zone 1. Operation of this element is therefore completely dependent on the dynamic bus replica, which must be defined
first. The bus differential zones are defined using the path SETTINGS  SYSTEM SETUP  BUS. The CT Trouble element 1
detects CT problems in any of the circuits actually connected to the differential zone defined as Bus Zone 1.
The CT TROUBLE ZONE 1 PICKUP setting specifies the differential current level that defines an abnormal bus state. If the
differential current in a given phase remains above this level for the time interval defined by the CT TROUBLE ZONE 1 DELAY
5 setting, CT Trouble is declared for the given phase by setting the appropriate FlexLogic output operand. The operand may
be configured to raise an alarm and block the bus differential function for the corresponding zone of protection.

Figure 5-101: CT trouble logic

SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
CT TROUBLE ZONE 1 AND
FUNCTION:
Enabled = 1
SETTING
BUS 1A CT:
Current Phasor
SETTINGS
BUS 1A STATUS:
Off = 0
BUS 1A DIRECTION:
ZONE 1 DIFFERENTIAL CURRENT
SETTINGS SETTINGS
CT TROUBLE ZONE 1 CT TROUBLE ZONE 1
... PICKUP:
RUN
Id1 > PICKUP
DELAY:
tPKP
FLEXLOGIC OPERAND
CT TROUBLE1 OP
ID1
SETTING
BUS 1X CT: 5
Current Phasor
SETTINGS
BUS 1X STATUS:
Off = 0
BUS 1X DIRECTION:
836759A4.CDR
5.7.5.3 Bus replica isolator monitoring

SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BUS REPLICA  ISOLATOR 1(48)
 ISOLATOR 1 ISOLATOR 1 Range: Disabled, Enabled
ISOLATOR 1 OPEN: Range: FlexLogic operand

 Off
ISOLATOR 1 CLOSED: Range: FlexLogic operand

 Off
ISOLATOR 1 ALARM Range: 0.00 to 120.00 s in steps of 0.05

 DELAY: 0.05 s
ISOLATOR 1 RESET: Range: FlexLogic operand

 Off
ISOLATOR 1 Range: Self-Reset, Latched, Disabled

 TARGET: Self-Reset
ISOLATOR 1 Range: Disabled, Enabled


Bus protection zone discrimination depends heavily on reliable isolator position feedback. Therefore, two isolator auxiliary
contacts – normally open and normally closed – must confirm the status of the isolator via the B90 contact inputs.
This element responds to both normally open and normally closed auxiliary contacts of an isolator or a tie-breaker in order
to assert the actual position of the isolator for the dynamic bus image. The element asserts two extra output operands
indicating "isolator alarm" (auxiliary contact discrepancy), and "block switching operations in the substation." The
operation of the element is summarized in the following table.
Table 5-30: Isolator monitoring logic
Isolator open Isolator closed Isolator position Alarm Block switching
auxiliary contact auxiliary contact
Off On CLOSED No No
Off Off LAST VALID After time delay Until Isolator
until acknowledged Position is valid
On On CLOSED
On Off OPEN No No
The position of an isolator is indicated by the ISOLATOR N POSITION FlexLogic operand (On = Closed, Off = Open). This operand
is used as a circuit connection status for the bus configuration. When "On", the related current is associated with a given
differential zone; when "Off", the current is excluded from differential calculations.
An isolator alarm FlexLogic operand, ISOLATOR 1 ALARM, is asserted after a settable time delay if the auxiliary contacts of the
isolator do not match (open-open, closed-closed instead of open-closed or closed-open), yielding an undefined isolator
position. The operand may be used to block user-selected protection functions and may be reset manually or remotely via
the resetting input operand.
The ISOLATOR 1 BLOCK operand is asserted as long as the isolator position is invalid. This operand may be used to block
switching operations in the substation. Typically, breakers and isolators that control currents flowing through a given
5 isolator shall be blocked from operation as long as isolator position is not resolved.
The element is effectively enabled only when PRODUCT SETUP  B90 FUNCTION  B90 FUNCTION is set to “Logic.” See the
Application of Settings chapter for details on the usage of the Bus Replica element.
ISOLATOR 1 OPEN — This setting specifies a FlexLogic operand that represents an auxiliary contact of the monitored isolator.
Typically this setting is a status of an appropriately wired input contact (“On” = isolator open).
ISOLATOR 1 CLOSED — This setting indicates a FlexLogic operand that represents an auxiliary contact of the monitored
isolator. Typically this setting is a status of an appropriately wired input contact (“On” = isolator closed).
Figure 5-102: Typical isolator open/closed settings
+
ISOLATOR 1
ISOLATOR 1 OPEN setting =

Contact Input 7a On
B90
FLEXLOGIC OPERANDS
F7a Contact Input F7a On
F7c Contact Input F7c On
F7b
ISOLATOR 1 CLOSED setting =

- Contact Input 7c On
836743A1.vsd
ISOLATOR 1 ALARM DELAY — This setting specifies a time delay after which an isolator alarm is issued by asserting the
operand assigned to ISOLATOR 1 ALARM. Set the delay longer than the slowest operation (transition) time of the isolator.

ISOLATOR 1 RESET — This setting indicates a FlexLogic operand that acknowledges the isolator alarm. Once the alarm is
acknowledged, the ISOLATOR 1 ALARM is reset. If the latter operand was configured to block protection, the blocking is
removed once the alarm is acknowledged. The acknowledge pulse must last at least 50 ms to take effect.
Figure 5-103: Isolator monitoring logic
SETTING
B90 FUNCTION:
Logic = 0
Protection = 1
SETTING
ISOLATOR 1
FUNCTION:
Disabled = 0 AND
Enabled = 1
SETTINGS
RUN
ISOLATOR 1 OPEN:
Off = 0 FLEXLOGIC OPERAND
Isolator
ISOLATOR 1 CLOSED: Position ISOLATOR 1 POSITION
Logic
Off = 0
SETTING
ISOLATOR 1 ALARM
DELAY:
FLEXLOGIC OPERAND
5
XOR
AND
tPKP
ISOLATOR 1 BLOCK
0
Positive
Edge S
Detector FLEXLOGIC OPERAND
ISOLATOR 1 ALARM
SETTING
OR
ISOLATOR 1 RESET: R
Off = 0
836002A1.vsd

INPUTS/OUTPUTS CHAPTER 5: SETTINGS
Figure 5-104: Isolator monitoring sample timing diagram
Isolator position valid Isolator position invalid Isolator position valid

(isolator opened) (isolator opened)
ISOLATOR 1 OPEN
ISOLATOR 1 CLOSED
ISOLATOR 1 POSITION
alarm time blocking signal resets when isolator

ISOLATOR 1 BLOCK delay position valid
alarm
ISOLATOR 1 ALARM acknowledged
alarm acknowledging
ISOLATOR 1 RESET signal
836744A1.vsd
5 5.8 Inputs/outputs
5.8.1 Contact inputs
SETTINGS  INPUTS/OUTPUTS  CONTACT INPUTS
 CONTACT INPUTS

 CONTACT INPUT H5a

 
CONTACT INPUT H5a ID: Range: up to 20 alphanumeric

 Cont Ip 1 characters
CONTACT INPUT H5a Range: 0.0 to 16.0 ms in steps of 0.5

 DEBNCE TIME: 6.0 ms
CONTACT INPUT H5a Range: Disabled, Enabled


 CONTACT INPUT xxx
 
 CONTACT INPUT
  THRESHOLDS
Ips H5a,H5c,H6a,H6c Range: 17, 33, 84, 166 Vdc

 THRESHOLD: 33 Vdc
Ips H7a,H7c,H8a,H8c Range: 17, 33, 84, 166 Vdc

 THRESHOLD: 33 Vdc

Ips xxx,xxx,xxx,xxx Range: 17, 33, 84, 166 Vdc
 THRESHOLD: 33 Vdc

CHAPTER 5: SETTINGS INPUTS/OUTPUTS
A contact inputs and outputs are digital signals associated with connections to hard-wired contacts. Wet and dry contacts
are supported.
The contact inputs menu contains configuration settings for each contact input as well as voltage thresholds for each
group of four contact inputs. Upon startup, the relay processor determines (from an assessment of the installed modules)
which contact inputs are available and then display settings for only those inputs.
An alphanumeric ID can be assigned to a contact input for diagnostic, setting, and event recording purposes. The CONTACT
IP X On (Logic 1) FlexLogic operand corresponds to contact input “X” being closed, while CONTACT IP X Off corresponds to
contact input “X” being open. The CONTACT INPUT DEBNCE TIME defines the time required for the contact to overcome
‘contact bouncing’ conditions. As this time differs for different contact types and manufacturers, set it as a maximum
contact debounce time (per manufacturer specifications) plus some margin to ensure proper operation. If CONTACT INPUT
EVENTS is set to “Enabled,” every change in the contact input state triggers an event.
A raw status is scanned for all Contact Inputs synchronously at the constant rate of 0.5 ms as shown in the following
figure. The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a
user-settable debounce time in order for the B90 to validate the new contact state. In the following figure, the debounce
time is set at 2.5 ms; thus the 6th sample in a row validates the change of state (mark no. 1 in the diagram). Once validated
(de-bounced), the contact input asserts a corresponding FlexLogic operand and logs an event as per user setting.
A time stamp of the first sample in the sequence that validates the new state is used when logging the change of the
contact input into the Event Recorder (mark no. 2 in the figure).
Protection and control elements, as well as FlexLogic equations and timers, are executed eight times in a power system
cycle. The protection pass duration is controlled by the frequency tracking mechanism. The FlexLogic operand reflecting
the debounced state of the contact is updated at the protection pass following the validation (marks no. 3 and 4 on the
figure that follows). The update is performed at the beginning of the protection pass so all protection and control functions,
as well as FlexLogic equations, are fed with the updated states of the contact inputs.
The FlexLogic operand response time to the contact input change is equal to the debounce time setting plus up to one
protection pass (variable and depending on system frequency if frequency tracking enabled). If the change of state occurs
5
just after a protection pass, the recognition is delayed until the subsequent protection pass; that is, by the entire duration
of the protection pass. If the change occurs just prior to a protection pass, the state is recognized immediately. Statistically
a delay of half the protection pass is expected. Owing to the 0.5 ms scan rate, the time resolution for the input contact is
below 1 ms.
For example, eight protection passes per cycle on a 60 Hz system correspond to a protection pass every 2.1 ms. With a
contact debounce time setting of 3.0 ms, the FlexLogic operand-assert time limits are: 3.0 + 0.0 = 3.0 ms and 3.0 + 2.1 = 5.1
ms. These time limits depend on how soon the protection pass runs after the debouncing time.
Regardless of the contact debounce time setting, the contact input event is time-stamped with a 1 s accuracy using the
time of the first scan corresponding to the new state (mark no. 2 shown). Therefore, the time stamp reflects a change in the
DC voltage across the contact input terminals that was not accidental as it was subsequently validated using the
debounce timer. Keep in mind that the associated FlexLogic operand is asserted/de-asserted later, after validating the
change.
The debounce algorithm is symmetrical: the same procedure and debounce time are used to filter the LOW-HIGH (marks
no.1, 2, 3, and 4 in the figure) and HIGH-LOW (marks no. 5, 6, 7, and 8) transitions.

VOLTAGE
Figure 5-105: Input contact debouncing mechanism and time stamp sample timing
INPUT
USER-PROGRAMMABLE THRESHOLD
6
2 1 3 5
Time stamp of the first
TM
Time stamp of the first At this time, the The FlexLogic scan corresponding to the
At this time, the new
scan corresponding to new (HIGH) operand is going to new validated state is
(LOW) contact state is
the new validated state is contact state is be asserted at this logged in the SOE record
validated
logged in the SOE record validated protection pass
7
RAW CONTACT
The FlexLogicTM
operand is going to be
STATE
de-asserted at this
protection pass
DEBOUNCE TIME
(user setting)
4
The FlexLogicTM operand
DEBOUNCE TIME
The FlexLogicTM operand changes reflecting the
SCAN TIME (user setting)
changes reflecting the validated contact state
FLEXLOGICTM
(0.5 msec) validated contact state

OPERAND
PROTECTION PASS
(8 times a cycle controlled by the
frequency tracking mechanism)
842709A1.cdr
5 Contact inputs are isolated in groups of four to allow connection of wet contacts from different voltage sources for each
group. The CONTACT INPUT THRESHOLDS determine the minimum voltage required to detect a closed contact input. This
value is selected according to the following criteria: 17 for 24 V sources, 33 for 48 V sources, 84 for 110 to 125 V sources
and 166 for 250 V sources.
For example, to use contact input H5a as a status input from the breaker 52b contact to seal-in the trip relay and record it
in the Event Records menu, make the following settings changes:
CONTACT INPUT H5a ID: "Breaker Closed (52b)"
CONTACT INPUT H5a EVENTS: "Enabled"
Note that the 52b contact is closed when the breaker is open and open when the breaker is closed.
5.8.2 Virtual inputs

SETTINGS  INPUTS/OUTPUTS  VIRTUAL INPUTS  VIRTUAL INPUT 1(64)
 VIRTUAL INPUT 1 VIRTUAL INPUT 1 Range: Disabled, Enabled
VIRTUAL INPUT 1 ID: Range: up to 20 alphanumeric characters

 Virt Ip 1
VIRTUAL INPUT 1 Range: Self-Reset, Latched

 TYPE: Latched
VIRTUAL INPUT 1 Range: Disabled, Enabled

The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include
signals generated by the local user interface. The virtual outputs are outputs of FlexLogic equations used to customize the
device. Virtual outputs can also serve as virtual inputs to FlexLogic equations.

There are 64 virtual inputs that can be individually programmed to respond to input signals from the keypad (via the
COMMANDS menu) and communications protocols. All virtual input operands are defaulted to “Off” (logic 0) unless the
appropriate input signal is received.
If the VIRTUAL INPUT x FUNCTION is to “Disabled,” the input is forced to off (logic 0) regardless of any attempt to alter the
input. If set to “Enabled,” the input operates as shown on the logic diagram and generates output FlexLogic operands in
response to received input signals and the applied settings.
There are two types of operation: self-reset and latched. If VIRTUAL INPUT x type is “Self-Reset,” when the input signal
transits from off to on, the output operand is set to on for only one evaluation of the FlexLogic equations and then return to
off. If set to “Latched,” the virtual input sets the state of the output operand to the same state as the most recent received
input.
The self-reset operating mode generates the output operand for a single evaluation of the FlexLogic equations. If the
operand is to be used anywhere other than internally in a FlexLogic equation, it likely needs to be lengthened in time. A
FlexLogic timer with a delayed reset can perform this function.
Figure 5-106: Virtual inputs logic
SETTING
VIRTUAL INPUT 1
FUNCTION:
Enabled=1 S
AND
Latch
“Virtual Input 1 to ON = 1”
SETTING
“Virtual Input 1 to OFF = 0” R VIRTUAL INPUT 1 ID:
AND
SETTING (Flexlogic Operand)
5
OR
Virt Ip 1
VIRTUAL INPUT 1
TYPE:
Latched AND
Self - Reset 827080A3.CDR
5.8.3 Contact outputs

5.8.3.1 Digital outputs
SETTINGS  INPUTS/OUTPUTS  CONTACT OUTPUTS  CONTACT OUTPUT H1
 CONTACT OUTPUT H1 CONTACT OUTPUT H1 ID Range: up to 20 alphanumeric characters
  Cont Op 1
OUTPUT H1 OPERATE: Range: FlexLogic operand

 Off
OUTPUT H1 SEAL-IN: Range: FlexLogic operand

 Off
CONTACT OUTPUT H1 Range: Disabled, Enabled

 EVENTS: Enabled
A contact inputs and outputs are digital signals associated with connections to hard-wired contacts. Wet and dry contacts
are supported.
Upon startup of the relay, the main processor determines from an assessment of the modules installed in the chassis
which contact outputs are available and then presents the settings for only these outputs. Where the contact input is non-
latching, the settings are as shown.
An ID can be assigned to each contact output. The signal that can OPERATE a contact output can be any FlexLogic
operand (virtual output, element state, contact input, or virtual input). An additional FlexLogic operand can be used to
SEAL-IN the relay. Any change of state of a contact output can be logged as an Event if programmed to do so.

For example, the trip circuit current is monitored by providing a current threshold detector in series with some Form-A
contacts (see the trip circuit example in the Digital Elements section). The monitor sets a flag (see the specifications for
Form-A). The name of the FlexLogic operand set by the monitor, consists of the output relay designation, followed by the
name of the flag; for example, Cont OP 1 IOn.
In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact used to interrupt current
flow after the breaker has tripped, to prevent damage to the less robust initiating contact. This can be done by monitoring
an auxiliary contact on the breaker which opens when the breaker has tripped, but this scheme is subject to incorrect
operation caused by differences in timing between breaker auxiliary contact change-of-state and interruption of current in
the trip circuit. The most dependable protection of the initiating contact is provided by directly measuring current in the
tripping circuit, and using this parameter to control resetting of the initiating relay. This scheme is often called trip seal-in.
This can be realized using the Cont OP 1 IOn FlexLogic operand to seal-in the contact output as follows:
CONTACT OUTPUT H1 ID: “Cont Op 1"
OUTPUT H1 OPERATE: any suitable FlexLogic operand
OUTPUT H1 SEAL-IN: “Cont Op 1 IOn”
CONTACT OUTPUT H1 EVENTS: “Enabled”
Figure 5-107: Contact input/output module type 6A contact 1 logic

SETTING
CONTACT OUTPUT H1 OPERATE
= On FLEXLOGIC OPERAND
OR Cont Op 1 Closed
Cont Op 1 Ion
Cont Op 1 Von
Cont Op 1 Voff
SETTING
CONTACT OUTPUT H1 SEAL-IN AND H1a
= On
H1b
5 H1c
859743A1.vsd
5.8.3.2 Latching outputs

SETTINGS  INPUTS/OUTPUTS  CONTACT OUTPUTS  CONTACT OUTPUT H1a
 CONTACT OUTPUT H1a OUTPUT H1a ID Range: up to 20 alphanumeric characters
  L-Cont Op 1
OUTPUT H1a OPERATE: Range: FlexLogic operand

 Off
OUTPUT H1a RESET: Range: FlexLogic operand

 Off
OUTPUT H1a TYPE: Range: Operate-dominant, Reset-dominant

 Operate-dominant
OUTPUT H1a EVENTS: Range: Disabled, Enabled

 Disabled
The latching output contacts are mechanically bi-stable and controlled by two separate (open and close) coils. As such
they retain their position even if the relay is not powered up. The relay recognizes all latching output contact cards and
populates the setting menu accordingly. On power up, the relay reads positions of the latching contacts from the hardware
before executing any other functions of the relay (such as protection and control features or FlexLogic).
The latching output modules, either as part of the relay or as individual modules, are shipped from the factory with all
latching contacts open. It is highly recommended to double-check the programming and positions of the latching contacts
when replacing a module.
Since the relay asserts the output contact and reads back its position, it is possible to incorporate self-monitoring
capabilities for the latching outputs. If any latching outputs exhibits a discrepancy, the LATCHING OUTPUT ERROR self-test
error is declared. The error is signaled by the LATCHING OUT ERROR FlexLogic operand, event, and target message.

OUTPUT H1a OPERATE — This setting specifies a FlexLogic operand to operate the ‘close coil’ of the contact. The relay seals-
in this input to safely close the contact. Once the contact is closed and the RESET input is logic 0 (off), any activity of the
OPERATE input, such as subsequent chattering, does not have any effect. With both the OPERATE and RESET inputs active
(logic 1), the response of the latching contact is specified by the OUTPUT H1a TYPE setting.
OUTPUT H1a RESET — This setting specifies a FlexLogic operand to operate the ‘trip coil’ of the contact. The relay seals-in
this input to safely open the contact. Once the contact is opened and the OPERATE input is logic 0 (off), any activity of the
RESET input, such as subsequent chattering, does not have any effect. With both the OPERATE and RESET inputs active (logic
1), the response of the latching contact is specified by the OUTPUT H1a TYPE setting.
OUTPUT H1a TYPE — This setting specifies the contact response under conflicting control inputs; that is, when both the
OPERATE and RESET signals are applied. With both control inputs applied simultaneously, the contact closes if set to
“Operate-dominant” and opens if set to “Reset-dominant.”
Figure 5-108: Contact input/output module type 4L contact 1 logic
SETTING
CONTACT OUTPUT H1a Non-volatile,
OPERATE = On Set-dominant
AND S
SETTING OR Latch On
CONTACT OUTPUT H1a TYPE Close
= Operate-dominant R
H1b
= Reset-dominant
Non-volatile,
SETTING OR Set-dominant
H1a
CONTACT OUTPUT H1a RESET AND S
= On Open
Latch
R
FLEXLOGIC OPERAND
Cont Op 1 Closed
859744A1.vsd
5
A latching output contact H1a is to be controlled from two user-programmable pushbuttons (buttons number 1 and 2). The
following settings are applied.
Program the Latching Outputs by making the following changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT
OUTPUTS  CONTACT OUTPUT H1a menu (assuming an H4L module):
OUTPUT H1a OPERATE: “PUSHBUTTON 1 ON”
OUTPUT H1a RESET: “PUSHBUTTON 2 ON”
Program the pushbuttons by making the following changes in the PRODUCT SETUP  USER-PROGRAMMABLE PUSHBUTTONS
 USER PUSHBUTTON 1 and USER PUSHBUTTON 2 menus:
A relay, having two latching contacts H1a and H1c, is to be programmed. The H1a contact is to be a Type-a contact, while
the H1c contact is to be a Type-b contact (Type-a means closed after exercising the operate input; Type-b means closed
after exercising the reset input). The relay is to be controlled from virtual outputs: VO1 to operate and VO2 to reset.
OUTPUTS  CONTACT OUTPUT H1a and CONTACT OUTPUT H1c menus (assuming an H4L module):
OUTPUT H1a OPERATE: “VO1”
OUTPUT H1a RESET: “VO2”
OUTPUT H1c OPERATE: “VO2”
OUTPUT H1c RESET: “VO1”

Since the two physical contacts in this example are mechanically separated and have individual control inputs, they do not
operate at exactly the same time. A discrepancy in the range of a fraction of a maximum operating time can occur.
Therefore, a pair of contacts programmed to be a multi-contact relay do not guarantee any specific sequence of operation
(such as make before break). If required, the sequence of operation must be programmed explicitly by delaying some of the
control inputs as shown in the next application example.
A make before break functionality must be added to the preceding example. An overlap of 20 ms is required to implement
this functionality.
Write the following FlexLogic equation (EnerVista example shown).
Set both timers (Timer 1 and Timer 2) to 20 ms pickup and 0 ms dropout.

5 Program the Latching Outputs by making the following changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT
OUTPUTS  CONTACT OUTPUT H1a and CONTACT OUTPUT H1c menus (assuming an H4L module):
OUTPUT H1c OPERATE: “VO2”
OUTPUT H1c RESET: “VO3”
A latching contact H1a is to be controlled from a single virtual output VO1. The contact is to remain closed as long as VO1
is high, and is to remain opened when VO1 is low. Program the relay as follows.
Write the following FlexLogic equation (EnerVista example shown).
OUTPUTS  CONTACT OUTPUT H1a menu (assuming an H4L module):

5.8.4 Virtual outputs

SETTINGS  INPUTS/OUTPUTS  VIRTUAL OUTPUTS  VIRTUAL OUTPUT 1(96)
 VIRTUAL OUTPUT 1 VIRTUAL OUTPUT 1 ID Range: up to 20 alphanumeric characters
  Virt Op 1
VIRTUAL OUTPUT 1 Range: Disabled, Enabled

The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include
signals generated by the local user interface. The virtual outputs are outputs of FlexLogic equations used to customize the
device. Virtual outputs can also serve as virtual inputs to FlexLogic equations.
There are 96 virtual outputs that can be assigned using FlexLogic. If not assigned, the output is forced to ‘OFF’ (Logic 0). An
ID also can be assigned to each virtual output. Virtual outputs are resolved in each pass through the evaluation of the
FlexLogic equations. Any change of state of a virtual output can be logged as an event if programmed to do so.
For example, if Virtual Output 1 is the trip signal from FlexLogic and the trip relay is used to signal events, the settings is
programmed as follows:
VIRTUAL OUTPUT 1 ID: "Trip"
VIRTUAL OUTPUT 1 EVENTS: "Disabled"
5.8.5 Resetting

SETTINGS  INPUTS/OUTPUTS  RESETTING
 RESETTING RESET OPERAND: Range: FlexLogic operand
5
  Off

SETTINGS  INPUTS/OUTPUTS  RESETTING
 RESETTING RESET OPERAND: Range: FlexLogic operand
  Off
RESET ANNUNCIATOR: Range: FlexLogic operand

 Off
Some events can be programmed to latch the front panel LED event indicators, target messages, and/or graphical front
panel annunciator windows. Once set, the latching mechanism holds the latched indicators, messages, or windows in the
set state after the initiating condition has cleared until a RESET command is received to return these latches (not including
FlexLogic latches) to the reset state where the initiating condition has cleared. The RESET command can be sent from the
front panel RESET button, a remote device via a communications channel, or any selected operand. The Modbus execute
function 05h with operation code 1 command is also available to perform the same function as the front panel RESET key.
RESET OPERAND — The three sources of RESET commands each activates the RESET OP FlexLogic operand. Each individual
source of a RESET command also activates its individual operand RESET OP (PUSHBUTTON), RESET OP (COMMS), or RESET OP
(OPERAND) to identify the source of the command. Each of these three operands generates an event in the event record
when activated. The RESET OPERAND setting here selects the operand that activates the RESET OP (OPERAND) operand.
RESET ANNUNCIATOR — Used to select a FlexLogic operand that when activated acknowledges/resets all annunciator
windows on the graphical front panel. The other methods to acknowledge/reset annunciator windows include:
• On the displayed page, press the RESET pushbutton with none of the annunciator windows selected to acknowledge/
reset all annunciator windows on that page
• To acknowledge/reset a specific annunciator window, use the Up, Down, Left and Right pushbuttons to select the
window, and press the RESET or ENTER pushbutton

• All annunciator windows can be reset remotely by programming a Virtual Input (for example Virtual Input 1) as the
input to the RESET ANNUNCIATOR setting. Then the Modbus execute function 05h with operation code 1000h command
(or function 10h with address 400h) is used to set the state of Virtual Input 1.
For the RESET ANNUNCIATOR setting, the RESET ANCTR OP FlexLogic operand is activated by the two sources of RESET
command, operand source and manual source. Each individual source of a RESET ANNUNCIATOR command also activates
its individual operand RESET OP (OPRD) or RESET ANCTR OP (MNUL) to identify the source of the command. Each of these two
operands generates an event in the event record when activated. The setting here selects the operand that activates the
RESET ANCTR OP (OPRD) operand. The RESET pushbutton on the front panel or the reset command from the software
activates the RESET ANCTR OP (MNUL) operand.
5.8.6 Direct inputs and outputs
5.8.6.1 Direct inputs

SETTINGS  INPUTS/OUTPUTS  DIRECT INPUTS  DIRECT INPUT 1(256)
 DIRECT INPUT 1 DIRECT INPUT 1 Range: up to 12 alphanumeric characters
  NAME: Dir Ip 1
DIRECT INPUT 1 Range: 0 to 16

 DEVICE ID: 0
DIRECT INPUT 1 Range: 0 to 256

 BIT NUMBER: 0
DIRECT INPUT 1 Range: On, Off, Latest/On, Latest/Off

 DEFAULT: Off
5  DIRECT INPUT 1
EVENTS: Disabled
These settings specify how the direct input information is processed.

DIRECT INPUT 1 NAME — This setting allows the user to assign a descriptive name to the direct input.
DIRECT INPUT 1 DEVICE ID — Represents the source of direct input 1. The specified direct input is driven by the device
identified here.
DIRECT INPUT 1 BIT NUMBER — The bit number to extract the state for direct input 1. Direct Input 1 is driven by the bit
identified as DIRECT INPUT 1 BIT NUMBER. This corresponds to the direct output number of the sending device.
DIRECT INPUT 1 DEFAULT STATE — Represents the state of the direct input when the associated direct device is offline. The
following choices are available:
• On — Defaults the input to Logic 1
• Off — Defaults the input to Logic 0
• Latest/On — Freezes the input in case of lost communications. When the latest state is not known, such as after relay
power-up but before the first communication exchange, the input defaults to Logic 1. When communication resumes,
the input becomes fully operational.
• Latest/Off — Freezes the input in case of lost communications. When the latest state is not known, such as after relay
power-up but before the first communication exchange, the input defaults to Logic 0. When communication resumes,
the input becomes fully operational.
5.8.6.2 Direct outputs

SETTINGS  INPUTS/OUTPUTS  DIRECT OUTPUTS  DIRECT OUTPUT 1(256)
 DIRECT OUTPUT 1 DIRECT OUT 1 NAME: Range: up to 12 alphanumeric characters
  Dir Out 1
DIRECT OUT 1 OPERAND: Range: FlexLogic operand

 Off

DIRECT OUTPUT 1 Range: Enabled, Disabled

DIRECT OUT 1 NAME — This setting allows the user to assign a descriptive name to the direct output.
DIR OUT 1 OPERAND — This sets the FlexLogic operand that determines the state of this direct output.
5.8.6.3 Application examples

The examples introduced in the earlier Direct Inputs and Outputs section (part of the Product Setup section) are continued
here to illustrate usage of the direct inputs and outputs.
Example 1: Extending input/output capabilities of a UR relay

Consider an application that requires additional quantities of contact inputs or output contacts or lines of programmable
logic that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED,
such as the C30, to satisfy the additional inputs/outputs and programmable logic requirements. The figure shows that two
IEDs are connected via single-channel digital communication cards.
Figure 5-109: Input and output extension via direct inputs and outputs
TX1
UR IED 1
RX1
TX1
UR IED 2
RX1
842711A1.CDR 5
Assume that contact input 1 from UR IED 2 is to be used by UR IED 1. The following settings are applied (Direct Input 5 and
bit number 12 are used, as an example).
UR IED 1:
DIRECT INPUT 5 DEVICE ID = “2”
DIRECT INPUT 5 BIT NUMBER = “12”
UR IED 2:
DIRECT OUT 12 OPERAND = “Cont Ip 1 On”
The Cont Ip 1 On operand of UR IED 2 is now available in UR IED 1 as DIRECT INPUT 5 ON.
Example 2: Interlocking busbar protection

A simple interlocking busbar protection scheme can be accomplished by sending a blocking signal from downstream
devices, say 2, 3 and 4, to the upstream device that monitors a single incomer of the busbar, as shown in the figure.

Figure 5-110: Sample interlocking busbar protection scheme
UR IED 1 BLOCK
UR IED 2 UR IED 3 UR IED 4
842712A1.CDR
Assume that Phase Instantaneous Overcurrent 1 is used by Devices 2, 3, and 4 to block Device 1. If not blocked, Device 1
trips the bus upon detecting a fault and applying a short coordination time delay.
The following settings are applied (assume Bit 3 is used by all 3 devices to send the blocking signal and Direct Inputs 7, 8,
and 9 are used by the receiving device to monitor the three blocking signals).
UR IED 2:
DIRECT OUT 3 OPERAND: "PHASE IOC1 OP"
UR IED 3:
DIRECT OUT 3 OPERAND: "PHASE IOC1 OP"
UR IED 4:
5 DIRECT OUT 3 OPERAND: "PHASE IOC1 OP"
UR IED 1:
DIRECT INPUT 7 DEVICE ID: "2"
DIRECT INPUT 7 BIT NUMBER: "3"
DIRECT INPUT 7 DEFAULT STATE: select "On" for security, select "Off" for dependability


Now the three blocking signals are available in UR IED 1 as DIRECT INPUT 7 ON, DIRECT INPUT 8 ON, and DIRECT INPUT 9 ON. Upon
losing communications or a device, the scheme is inclined to block (if any default state is set to “On”), or to trip the bus on
any overcurrent condition (all default states set to “Off”).
Example 3: Pilot-aided schemes

Consider a three-terminal line protection application shown in the following figure.

Figure 5-111: Three-terminal line application
UR IED 1 UR IED 2
UR IED 3 842713A1.CDR
Assume the Hybrid Permissive Overreaching Transfer Trip (Hybrid POTT) scheme is applied using the architecture shown as
follows. The scheme output operand HYB POTT TX1 is used to key the permission.
Figure 5-112: Single-channel open-loop configuration
TX1 RX1 RX2

UR IED 1 UR IED 2
RX1 TX1 TX2
UR IED 3
RX1 5
TX1
842714A1.CDR
In this architecture, Devices 1 and 3 do not communicate directly. Therefore, Device 2 must act as a ‘bridge’. The following
settings are applied:
UR IEC 1:
DIRECT OUT 2 OPERAND: "HYB POTT TX1"
DIRECT INPUT 5 BIT NUMBER: "2" (this is a message from IED 2)
DIRECT INPUT 6 BIT NUMBER: "4" (effectively, this is a message from IED 3)
UR IED 3:
DIRECT INPUT 5 BIT NUMBER: "2" (this is a message from IED 2)
DIRECT INPUT 6 BIT NUMBER: "3" (effectively, this is a message from IED 1)
UR IED 2:
DIRECT OUT 3 OPERAND: "DIRECT INPUT 5" (forward a message from 1 to 3)
DIRECT OUT 4 OPERAND: "DIRECT INPUT 6" (forward a message from 3 to 1)
The figure shows the signal flow among the three IEDs.

TESTING CHAPTER 5: SETTINGS
Figure 5-113: Signal flow for direct input and output
UR IED 1 UR IED 2
DIRECT OUT 2 = HYB POTT TX1 DIRECT INPUT 5
DIRECT INPUT 5 DIRECT OUT 2 = HYB POTT TX1
DIRECT INPUT 6 DIRECT OUT 4 = DIRECT INPUT 6
DIRECT OUT 3 = DIRECT INPUT 5
DIRECT INPUT 6
UR IED 3 DIRECT INPUT 5

DIRECT INPUT 6
DIRECT OUT 2 = HYB POTT TX1
842717A1.CDR
In three-terminal applications, both the remote terminals must grant permission to trip. Therefore, at each terminal, direct
inputs 5 and 6 are ANDed in FlexLogic and the resulting operand configured as the permission to trip (HYB POTT RX1
setting).
5.9 Testing
5
5.9.1 Test mode function
SETTINGS  TESTING  TEST MODE FUNCTION
 TESTING TEST MODE Range: Disabled, Isolated, Forcible
The B90 provides a test facility to verify the functionality of contact inputs and outputs, some communication functions
and the Phasor Measurement Unit (PMU, where applicable), using simulated conditions. It is accessible in the software and
The TEST MODE FUNCTION can be in one of three states: Disabled, Isolated, or Forcible. In UR 7.7 and later, as outlined in the
Simulation section that follows, the UR test mode and GOOSE simulation mode are Isolated, and they no longer depend on
the UR TEST MODE FUNCTION.
The Disabled mode is intended for normal in service operation; the relay protection, control, and communication function
is normal. Test features are disabled, except channel tests and Phasor Measurement Unit tests remain usable when
provided.
The Isolated mode is intended to allow the relay to be quickly placed in a state where the relay cannot negatively impact
the power system or other parts of the substation automation system. This is to allow changing settings, loading new
firmware, changing hardware modules, and changing communication connections. As far as practical all relay output
signals are blocked. Contact outputs are de-energized, latching outputs are frozen. Commands to HardFiber Bricks are
blocked. GOOSE transmissions have their "simulation" flag (also known as "test" flag) set, which results in the messages not
being accepted by compliant receiving devices that do not have a "Sim" data attribute set. The quality attribute of values
that can be output via IEC 61850 MMS services are set to "invalid," which results in the values not being used for
operational purposes by compliant receiving devices. Direct I/O channel tests and PMU tests are usable on applicable
models.
The Forcible mode is intended for testing involving forcing relay operation by test signal injection and verifying correct
relay output. This mode is also for tests to verify the relay outputs (both contact and communications) have the intended
impact on specific power system devices or on specific other substation automation devices. Contact outputs can be
selectively enabled or forced as described in the following two sections. Shared outputs to Bricks have their test mode flag

CHAPTER 5: SETTINGS TESTING
raised, which results in their value only being accepted by relays also in forcible mode. GOOSE transmissions have the
"simulation" flag set, which results in these only being accepted by other devices that have their "Sim" data attribute set.
The "Sim" data attribute in the relay is set, so that if GOOSE messages are received with the "simulation" flag set, these are
used in place of the normal messages. The quality attribute of values that are output via IEC 61850 MMS services are set to
"valid" + "test," which signals that the values are not to be used for operational purposes.
Otherwise, the UR remains fully operational while in the Forcible test mode, allowing for various testing procedures. In
particular, the protection and control elements, and FlexLogic function normally. Other than the IEC 61850 protocol,
communications based inputs and outputs remain fully operational. The test procedure must take this into account. Direct
I/O channel tests and PMU tests are usable on applicable models.
The test mode can be selected through the front panel, EnerVista UR Setup software, or IEC 61850 control to LLN0.Mod.
LLN0.Mod.ctlVal "on" selects Disabled, "test/blocked" selects Isolated, and "test" selects Forcible. The TEST MODE FUNCTION
setting can only be changed by a direct user command. Following a restart, power up, settings upload, or firmware
upgrade, the test mode remains at the last programmed value. This allows a UR that has been placed in isolated mode to
remain isolated during testing and maintenance activities.
5.9.2 Test mode forcing

SETTINGS  TESTING  TEST MODE FORCING
 TESTING TEST MODE FORCING: Range: FlexLogic operand
  On
When in Forcible mode, the operand selected by the TEST MODE FORCING setting dictates further response of the B90 to
testing conditions, as described in the following two sections.
The test mode state is indicated on the relay front panel by a combination of the Test Mode LED indicator, the In-Service
LED indicator, and by the critical fail relay, as shown in the following table. 5
Table 5-31: Test mode operation
TEST MODE In-service Test mode Critical fail TEST MODE Contact input and output behavior
FUNCTION LED LED relay FORCING
Disabled Unaffected Off Normal No effect Normal
Isolated Off On De-energized No effect Contact outputs disabled
Forcible Off Flashing De-energized Off Normal
On Controlled by forcing features
On restart, the TEST MODE FORCING setting and the force contact input and force contact output settings revert to
their default states.
5.9.3 Force contact inputs

SETTINGS  TESTING  FORCE CONTACT INPUTS
 FORCE CONTACT FORCE Cont Ip 1 Range: Normal, Open, Closed
 INPUTS  : Normal
FORCE Cont Ip 2 Range: Normal, Open, Closed

 : Normal

FORCE Cont Ip xx Range: Normal, Open, Closed
 : Normal
The force contact inputs feature provides a method of performing checks on the function of all contact inputs.
While in Forcible test mode, the relay contact inputs can be pre-programmed to respond in the following ways:

TESTING CHAPTER 5: SETTINGS
• If set to “Normal,” the input remains fully operational. It is controlled by the voltage across its input terminals and can
be turned on and off by external circuitry. Select this value if a given input must be operational during the test. This
includes, for example, an input initiating the test, or being a part of a user pre-programmed test sequence.
• If set to “Open,” the input is forced to report as opened (Logic 0) while the operand selected by TEST MODE FORCING
setting is On, regardless of the voltage across the input terminals. While the selected operand is Off, the input behaves
as it does when in service.
• If set to “Closed,” the input is forced to report as closed (Logic 1) while the operand selected by TEST MODE FORCING
setting is On regardless of the voltage across the input terminals. While the selected operand is Off, the input behaves
as it does when in service.
5.9.4 Force contact outputs

SETTINGS  TESTING  FORCE CONTACT OUTPUTS
 FORCE CONTACT FORCE Cont Op 1 Range: Normal, Energized, De-energized, Freeze
 OUTPUTS  : Normal
FORCE Cont Op 2 Range: Normal, Energized, De-energized, Freeze

 : Normal

FORCE Cont Op xx Range: Normal, Energized, De-energized, Freeze

5 : Normal
The force contact outputs feature provides a method of performing checks on the function of all contact outputs.
While in Forcible test mode, the relay contact outputs can be pre-programmed to respond in the following ways:
• If set to “Normal,” the contact output remains fully operational. It operates when its control operand is logic 1 and
resets when its control operand is logic 0.
• If set to “Energized,” the output closes and remains closed while the operand selected by the TEST MODE FORCING
setting is On, regardless of the status of the operand configured to control the output contact. While the selected
operand is Off, the output behaves as it does when in service.
• If set to “De-energized,” the output opens and remains opened while the operand selected by the TEST MODE FORCING
setting is On, regardless of the status of the operand configured to control the output contact. While the selected
operand is Off, the output behaves as it does when in service.
• If set to “Freeze,” the output retains its position at the instant before the TEST MODE FUNCTION was Forcible and the
operand selected by the TEST MODE FORCING setting was On, regardless of later changes in the status of the operand
configured to control the output contact. While the selected operand is Off, the output behaves as it does when in
service.

CHAPTER 5: SETTINGS SIMULATION
5.10 Simulation
5.10.1 GOOSE
SETTINGS  SIMULATION  GOOSE
 GOOSE Tx GOOSE SIM MODE: Range: Enabled, Disabled
  Disabled
SIM q.VALIDITY: Range: NONE, GOOD, INVALID, QUESTIONABLE

 NONE
SIM q.TEST: Range: NONE, TRUE, FALSE

 NONE
ACCEPT SIM GOOSE & SV: Range: Enabled, Disabled

 Disabled
Prior to UR 7.7, when the UR TEST MODE FUNCTION is set to "Isolated" or "Forcible," the sim bit in the header of all
transmitted GOOSE messages is set to "TRUE," so that the UR plays the simulator role during the testing and
commissioning phases. The "Sim" data attribute in the relay is set (<MasterLD>/LPHD1.Sim.stVal = TRUE), so that if GOOSE
messages are received with the "simulation" flag set, these are used in place of the normal messages. The quality attribute
values that are transmitted via GOOSE services are set to "valid" + "test."
In UR 7.7 and later, the UR test mode and GOOSE simulation mode are isolated. The sim bit in the transmitted GOOSE
messages and the relay "Sim" attribute (<MasterLD>/LPHD1.Sim.stVal) are controlled via new Modbus settings and MMS
control requests. They no longer depend on the UR TEST MODE FUNCTION.
When the B90 is set to IEC 61850 Edition 2, the settings display in the software and front panel. When using IEC 61850
Edition 1, the settings display in the software and are read-only.
5
Tx GOOSE SIM MODE — When set to Disabled, the sim bit in all transmitted GOOSE messages are set to FALSE. When set to
Enabled, the sim bit in all transmitted GOOSE messages are set to TRUE. This setting also is accessible from IEC 61850
client control to <MasterLD>/LPHD1.TxGoSim.
SIM q.VALIDITY — This setting simulates the validity bits of the quality attribute values included in all transmitted GOOSE
messages. This setting is used when Tx GOOSE SIM MODE is set to Enabled. When this setting is set to None, the q.Validity
bits are set based on the logical node behavior value. When set to any other value, the q.Validity bits of quality attributes
included in all transmitted GOOSE messages are set to the selected value.
SIM q.TEST — This setting simulates the Test bit of the quality attribute values included in all transmitted GOOSE messages.
This setting is used when Tx GOOSE SIM MODE is set to Enabled. When this setting is set to None, the q.Test bit is set based
on the relay TEST MODE FUNCTION. When set to any other value, the q.Test bit of quality attributes included in all
transmitted GOOSE messages is set to the selected value.
ACCEPT SIM GOOSE & SV — When set to Disabled, the relay "Sim" attribute (<MasterLD>/LPHD1.Sim.stVal) is set to False and
the GOOSE messages received with simulation flag set are ignored. When set to Enabled, the relay "Sim" attribute
(<MasterLD>/LPHD1.Sim.stVal) is set to True, so that if GOOSE messages are received with the "simulation" flag set, these
are used in place of the normal messages. This setting also is accessible from IEC 61850 client control to <MasterLD>/
LPHD1.Sim.

SIMULATION CHAPTER 5: SETTINGS

Chapter 6: Actual values
Actual values
This chapter outlines viewing of data on the front panel and in the software.
6.1 Actual Values menu
 ACTUAL VALUES  Access in EnerVista

 FRONT PANEL   See page 6-2

 ACTUAL VALUES  CONTACT INPUTS See page 6-4
 STATUS  
 VIRTUAL INPUTS See page 6-4

  
 RxGOOSE BOOLEAN See page 6-4

  INPUTS
 RxGOOSE DPS INPUTS See page 6-4

 
 CONTACT OUTPUTS See page 6-5

 
 VIRTUAL OUTPUTS See page 6-5

 
 RxGOOSE STATUS See page 6-5

 
 RxGOOSE See page 6-6

  STATISTICS
 FLEX STATES See page 6-6

 
 ETHERNET See page 6-6

 
 REAL TIME CLOCK See page 6-7

  SYNCHRONIZING

FRONT PANEL CHAPTER 6: ACTUAL VALUES
 DIRECT INPUTS See page 6-7

 
 DIRECT DEVICES See page 6-8

  STATUS
 COMM STATUS See page 6-8

  REMAINING CONNECT
 PRP See page 6-9

 
 TxGOOSE STATUS See page 6-9

 
 PROTOCOL See page 6-10

  
 ACTUAL VALUES  BUS See page 6-11

 METERING  
 CURRENTS See page 6-11

  
 VOLTAGES See page 6-12

 
 FREQUENCY See page 6-12

 
 RxGOOSE Analogs See page 6-12

  
 ACTUAL VALUES  USER-PROGRAMMABLE See page 6-12

 RECORDS   FAULT REPORTS
 EVENT RECORDS See page 6-13

  
 OSCILLOGRAPHY See page 6-14

 
6 
 ACTUAL VALUES  MODEL INFORMATION See page 6-15

 PRODUCT INFO  
 FIRMWARE REVISIONS See page 6-16

 
For status reporting, ‘On’ represents Logic 1 and ‘Off’ represents Logic 0.
6.2 Front panel

6.2.1 Enhanced and basic front panels
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the
front panel.
To view the front panel in EnerVista software:
1. Click Actual Values > Front Panel.

CHAPTER 6: ACTUAL VALUES FRONT PANEL
Figure 6-1: Front panel use in the software (C60 shown)

The graphical front panel is a hardware option.
Annunciator alarms can be acknowledged and reset, and LEDs and pushbuttons can be viewed. 6
To view alarms for the graphical front panel in EnerVista:
1. Access Actual Values > Graphical Panel > Annunciator Panel. Alarms are listed, allowing remote acknowledgement/
reset.
2. Click the Acknowledge or Reset button for an alarm.
Figure 6-2: Annunciator alarms displayed in the software)
To view LEDs and pushbuttons on the graphical front panel in EnerVista:

1. Access Actual Values > Graphical Panel > LEDs or Pushbuttons. The window displays.

STATUS CHAPTER 6: ACTUAL VALUES
6.3 Status
6.3.1 Contact inputs
ACTUAL VALUES  STATUS  CONTACT INPUTS
 CONTACT INPUTS Cont Ip 1 Range: On, Off
  Off

Cont Ip xx Range: On, Off
 Off
The present status of the contact inputs is shown here. The first line of a message display indicates the ID of the contact
input. For example, ‘Cont Ip 1’ refers to the contact input in terms of the default name-array index. The second line of the
display indicates the logic state of the contact input.

ACTUAL VALUES  STATUS  VIRTUAL INPUTS
 VIRTUAL INPUTS Virt Ip 1 Range: On, Off
  Off

Virt Ip 64 Range: On, Off
 Off
The present status of the 64 virtual inputs is shown here. The first line of a message display indicates the ID of the virtual
input. For example, ‘Virt Ip 1’ refers to the virtual input in terms of the default name. The second line of the display indicates
the logic state of the virtual input.
6
6.3.3 RxGOOSE boolean inputs
ACTUAL VALUES  STATUS  RxGOOSE BOOLEANS
 RxGOOSE BOOLEANS RxGOOSE BOOLEAN 1 Range: On, Off
  STATUS: Off

RxGOOSE BOOLEAN 256 Range: On, Off
 STATUS: Off
The B90 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time
of ordering. See the Order Codes section of chapter 2 for details.
6.3.4 RxGOOSE DPS inputs

ACTUAL VALUES  STATUS  RxGOOSE DPS
 RxGOOSE DPS RxGOOSE DPS 1 Range: On, Off, Intermediate, Bad
  Status: Intermediate

RxGOOSE DPS 16 Range: On, Off, Intermediate, Bad
 Status: Intermediate

CHAPTER 6: ACTUAL VALUES STATUS
6.3.5 Contact outputs

ACTUAL VALUES  STATUS  CONTACT OUTPUTS
 CONTACT OUTPUTS Cont Op 1 Range: On, Off, VOff, VOn, IOn, IOff
  Off

Cont Op xx Range: On, Off, VOff, VOn, IOn, IOff
 Off
The present state of the contact outputs is shown here. The first line of a message display indicates the ID of the contact
output. For example, ‘Cont Op 1’ refers to the contact output in terms of the default name-array index. The second line of
the display indicates the logic state of the contact output.
For form-A contact outputs, the state of the voltage and current detectors is displayed as Off, VOff, IOff, On, IOn, and VOn.
For form-C contact outputs, the state is displayed as Off or On.
6.3.6 Virtual outputs

ACTUAL VALUES  STATUS  VIRTUAL OUTPUTS
 VIRTUAL OUTPUTS Virt Op 1 Range: On, Off
  Off

Virt Op 96 Range: On, Off
 Off
The present state of up to 96 virtual outputs is shown here. The first line of a message display indicates the ID of the virtual
output. For example, ‘Virt Op 1’ refers to the virtual output in terms of the default name-array index. The second line of the
6
display indicates the logic state of the virtual output, as calculated by the FlexLogic equation for that output.
6.3.7 RxGOOSE status

ACTUAL VALUES  STATUS  RxGOOSE STATUS
 RxGOOSE All RxGOOSE Online: Range: Yes, No
 STATUS  Yes
RxGOOSE 1 Status: Range: Online, Offline

 Offline

RxGOOSE 64 Status: Range: Online, Offline
 Offline
The All RxGOOSE Online actual value does not consider RxGOOSE that are not configured or are not used by any RxGOOSE
Input.

6.3.8 RxGOOSE statistics

ACTUAL VALUES  STATUS  RxGOOSE STATISTICS  RxGOOSE 1(64)
 RxGOOSE 1 RxGOOSE 1 Range: 0 up to 4,294,967,295
  stNum: 0
RxGOOSE 1 Range: 0 up to 4,294,967,295

 sqNum: 0
R-RxGOOSE 1 Range: On, Off

 IGMP: Off
stNum — State number. The most recently received value in GOOSE message field stNum. The publisher increments stNum
each time that the state of one or more of the GOOSE message members is sent with a revised value.
sqNum — Sequence number. The most recently received value in GOOSE message field sqNum. The publisher sets sqNum
to zero each time the state of one or more of the GOOSE message members is sent with a new value, and it increments it
whenever a GOOSE message is resent without any member value change.
IGMP — Multicast (SSM and ASM) modes of R-GOOSE reception require that the B90 device subscribe to a multicast group
over the Internet Group Management Protocol (IGMP) enabled network. R-RxGOOSE## IGMP status On indicates that IGMP
negotiation with a network device (for example a router) was successful. In the case where setting R-RxGOOSE1 DST IP is
configured to a multicast address and this status indicates Off, R-GOOSE reception cannot be successful, and therefore
communication network diagnosis needs to be carried out. This status is relevant to R-GOOSE reception when configured
for SSM or ASM reception modes. It is not relevant for GOOSE or for R-GOOSE in unicast reception mode.
6.3.9 Flex States

ACTUAL VALUES  STATUS  FLEX STATES
6  FLEX STATES
 PARAM 1: Off Range: On, Off
 Off

PARAM 256: Off Range: On, Off
 Off
There are 256 FlexStateTM bits available. The second line value indicates the state of the given FlexState bit.
6.3.10 Ethernet
ACTUAL VALUES  STATUS  ETHERNET
 ETHERNET ETHERNET PRI LINK Range: Fail, OK
  STATUS: Fail
ETHERNET SEC LINK Range: Fail, OK

 STATUS: Fail
ETHERNET TER LINK Range: Fail, OK

 STATUS: Fail
These values indicate the status of the first, second, and third Ethernet links.

6.3.11 Real time clock synchronizing

ACTUAL VALUES  STATUS  REAL TIME CLOCK SYNCHRONIZING
 REAL TIME CLOCK RTC SYNC SOURCE: Range: see below
 SYNCHRONIZING  None
GRANDMASTER ID: Range: any 8 octet value

 0X0000000000000000
ACCURACY: Range: 0 to 999,999,999 ns

 999999999 ns
PORT 1 PTP STATE: Range: Disabled, No Signal, Calibrating, Synch’d (No

 No Signal Pdelay), Synchronized


PTP - IRIG-B DELTA: Range: -500,000,000 to +500,000,000 ns

 500000000 ns
This item displays in the software when the product includes an IEEE 1588 software option.
RTC SYNC SOURCE actual value is the time synchronizing source the relay is using at present. Possible sources are: Port 1
PTP Clock, Port 2 PTP Clock, Port 3 PTP Clock, IRIG-B, SNTP1, SNTP2, and None. An actual value displays when the relay
includes the IEEE 1588 software option.
The GRANDMASTER ID is the grandmasterIdentity code being received from the present PTP grandmaster, if any. When the
relay is not using any PTP grandmaster, this actual value is zero. The grandmasterIdentity code is specified by PTP to be
globally unique, so one can always know which clock is grandmaster in a system with multiple grandmaster-capable
clocks.
ACCURACY is the estimated maximum time error at present in the RTC, considering the quality information imbedded in the
6
received time signal. The value 999,999,999 indicates that the magnitude of the estimated error is one second or more, or
that the error cannot be estimated.
PORT 1…3 PTP STATE is the present state of the port’s PTP clock. The PTP clock state is:
• Disabled is the port’s function setting is Disabled
• No Signal if enabled but no signal from an active master has been found and selected
• Calibrating if an active master has been selected but lock is not at present established
• Synch’d (No Pdelay) if the port is synchronized, but the peer delay mechanism is non-operational
• Synchronized if synchronized
PTP - IRIG-B DELTA is the time difference, measured in nanoseconds, between the fractional seconds portion of the time
being received via PTP and that being received via IRIG-B. A positive value indicates that PTP time is fast compared to IRIG-
B time.
6.3.12 Direct inputs

ACTUAL VALUES  STATUS  DIRECT INPUTS
 DIRECT INPUTS AVERATE MSG RETURN
  TIME CH1: 0 ms
UNRETURNED MSG
 COUNT CH1: 0

CRC FAIL COUNT

 CH1: 0
AVERAGE MSG RETURN

 TIME CH2: 0 ms
UNRETURNED MSG
 COUNT CH2: 0
CRC FAIL COUNT

 CH2: 0
DIRECT INPUT 1:
 On

DIRECT INPUT 256:
 On
The AVERAGE MSG RETURN TIME is the time taken for direct output messages to return to the sender in a direct input/output
ring configuration (this value is not applicable for non-ring configurations). This is a rolling average calculated for the last
ten messages. There are two return times for dual-channel communications modules.
The UNRETURNED MSG COUNT values (one per communications channel) count the direct output messages that do not
make the trip around the communications ring. The CRC FAIL COUNT values (one per communications channel) count the
direct output messages that have been received but fail the CRC check. High values for either of these counts can indicate
on a problem with wiring, the communication channel, or one or more relays. The UNRETURNED MSG COUNT and CRC FAIL
COUNT values can be cleared using the CLEAR DIRECT I/O COUNTERS command.
The DIRECT INPUT 1 to DIRECT INPUT (256) values represent the state of each direct input.
6.3.13 Direct devices status

ACTUAL VALUES  STATUS  DIRECT DEVICES STATUS
 DIRECT DEVICES DIRECT DEVICE 1 Range: Offline, Online

6  STATUS STATUS: Offline

DIRECT DEVICE 16 Range: Offline, Online
 STATUS: Offline
These actual values represent the state of direct devices 1 through 16.
6.3.14 Remaining connection status

ACTUAL VALUES  STATUS  COMM STATUS REMAINING CONNECT
 COMM STATUS MMS TCP(max 5) Range: 0 to 5
 REMAINING CONNECT  5
MODBUS TCP (max 4) Range: 0 to 4

 4
DNP TCP(max 2) Range: 0 to 2

 2
IEC-104 TCP(max 2) Range: 0 to 2

 2
SFTP (max 4) Range: 0 to 4

 4

These values specify the remaining number of TCP connections still available for each protocol. The display depends on the
options applicable to your device. Each time a connection is used, the remaining number of connections decrements.
When released, the remaining number of connections increments. If no connection is made over the specific protocol, the
number equals the maximum number available for the specific protocol.
For example, the maximum number of Modbus TCP connections is 4. Once an EnerVista session is opened on a computer
connected to the UR over Ethernet, the Modbus TCP status shows 3. If the EnerVista application is closed, the Modbus TCP
status shows 4.
For the graphical front panel, the remaining connections refer to TCP connections only.
MMS TCP — The number of IEC 61850 connections remaining.
6.3.15 Parallel Redundancy Protocol (PRP)

The Parallel Redundancy Protocol (PRP) defines a redundancy protocol for high availability in substation automation
networks.
ACTUAL VALUES  STATUS  PRP STATUS
 PRP STATUS Total Rx Port A: Range: 0 to 4G, blank if PRP disabled
  0
Total Rx Port B: Range: 0 to 4G, blank if PRP disabled

 0
Mismatches Port A: Range: 0 to 4G, blank if PRP disabled

 0
Mismatches Port B: Range: 0 to 4G, blank if PRP disabled

 0
Total Errors: Range: 0 to 4G, blank if PRP disabled

 0
The B90 is provided with optional PRP capability. This feature is specified as a software option at the time of
ordering. See the Order Codes section in chapter 2 for details.
6
Total Received Port A is a counter for total messages received (either from DANPs or from SANs) on Port A.
Total Received Port B is a counter for total messages received (either from DANPs or from SANs) on Port B.
Total Errors is a counter for total messages received with an error (bad port code, frame length too short).
Mismatches Port A is a counter for total messages received with an error on Port A (PRP frame, but port received through
and LAN ID in the frame do not match).
Mismatches Port B is a counter for total messages received with an error on Port B (PRP frame, but port received through
and LAN ID in the frame do not match).
6.3.16 TxGOOSE status

ACTUAL VALUES  STATUS  TxGOOSE STATUS
 TxGOOSE STATUS R-TxGOOSE 1 Range: On, Off
  ARP: Off

R-TxGOOSE 16 Range: On, Off
 ARP: Off

METERING CHAPTER 6: ACTUAL VALUES
This status is relevant to R-GOOSE reception when configured for SSM or ASM reception modes. It is not relevant for GOOSE
or for R-GOOSE in unicast reception mode.
ARP — The unicast mode of R-GOOSE transmission requires Address Resolution Protocol (ARP) for the resolution of the
network layer address into the MAC layer address. R-TxGOOSE## ARP status On indicates that ARP responses are being
received and the destination MAC address for R-GOOSE transmissions has been obtained. This status remains Off if
TxGOOSE## is not configured for R-GOOSE. It also remains Off if setting R-TxGOOSE1 DST IP is set to a multicast address. In
the case where setting R-TxGOOSE1 DST IP is configured with a unicast address and this status indicates Off, TxGOOSE##
transmission will be off, and therefore communication network diagnosis needs to be carried out.
This status is only applicable for R-GOOSE transmission with setting R-TxGOOSE1 DST IP set to a unicast IP address. It is not
applicable for GOOSE or for R-GOOSE when setting R-TxGOOSE1 DST IP is multicast.
6.3.17 Protocol
ACTUAL VALUES  STATUS  PROTOCOL
 PROTOCOL IEC61850 EDITION: Range: Edition1, Edition2
  Edition2
Displays the IEC 61850 edition currently being used, as set under Settings > Product Setup > Communications > Protocol
> IEC61850 SCL Edition. This value displays only on the front panel.
6 6.4 Metering
6.4.1 Metering conventions
6.4.1.1 UR convention for measuring phase angles

All phasors calculated by URs and used for protection, control and metering functions are rotating phasors that maintain
the correct phase angle relationships with each other at all times.
For display and oscillography purposes, all phasor angles in a given relay are referred to an AC input channel pre-selected
by the SETTINGS  SYSTEM SETUP  POWER SYSTEM  FREQUENCY AND PHASE REFERENCE setting. This setting defines a
particular AC signal source to be used as the reference.
If the AC signal pre-selected by the relay upon configuration is not measurable, the phase angles are not referenced. The
phase angles are assigned as positive in the leading direction, and are presented as negative in the lagging direction, to
more closely align with power system metering conventions. The figure illustrates this.

CHAPTER 6: ACTUAL VALUES METERING
Figure 6-3: UR phase angle measurement convention

-270o
-225o -315o
positive
angle
direction
-180o 0o
UR phase angle
reference
-135o -45o
-90o
827845A1.CDR
6.4.2 Bus zone

ACTUAL VALUES  METERING  BUS  BUS ZONE 1(6)
 BUS ZONE 1 BUS ZONE 1 DIFF:
  0.000 A 0.0°
BUS ZONE 1 REST:

 0.000 A 0.0°
These values display the differential and restraint currents phasors for each bus zone. The magnitudes are displayed in
primary amperes. 6
There is no cutoff level applied to the differential and restraint currents computed by the B90. Therefore, a small
differential current reflecting CT inaccuracies and bus leakage current can be present during balanced conditions.
This is done to achieve a more accurate differential balance and to provide a direct indication of the real differential
current, as excluding small currents or not accounting for CT errors can impose significant unaccounted
differential current. It is advisable to set the minimum pickup for 87B protection greater than the maximum
differential current during normal load conditions.
6.4.3 Currents
ACTUAL VALUES  METERING  CURRENTS
 CURRENTS F1 CURRENT:
  0.000 A 0.0°
F2 CURRENT:
 0.000 A 0.0°

S8 CURRENT:
 0.000 A 0.0°
The metered current values for each terminal are displayed in this menu.

RECORDS CHAPTER 6: ACTUAL VALUES
6.4.4 Voltages
ACTUAL VALUES  METERING  VOLTAGES
 VOLTAGES F5 VOLTAGE:
  0.000 V 0.0°
F6 VOLTAGE:
 0.000 V 0.0°

S8 VOLTAGE:
 0.000 V 0.0°
This menu displays the metered voltage values for each terminal.
6.4.5 Frequency
ACTUAL VALUES  METERING  FREQUENCY
 FREQUENCY FREQUENCY:
  0.00 Hz
TRACKING FREQUENCY:
 60.00 Hz
This menu displays the metered frequency value and the tracking frequency. The frequency is tracked based on the
selection of the reference source with the FREQUENCY AND PHASE REFERENCE setting in the SETTINGS  SYSTEM SETUP 
POWER SYSTEM menu. See the Power System section of chapter 5 for details.
6.4.6 RxGOOSE analogs

ACTUAL VALUES  METERING  RxGOOSE Analogs
6  RxGOOSE
 Analogs  RxGOOSE Analog 1
0.000

RxGOOSE Analog 32
 0.000
The B90 is provided with optional GOOSE communications capability. This feature is specified as a software
option at the time of ordering. See the Order Codes section of chapter 2 for details.
The RxGOOSE Analog values display in this menu. The RxGOOSE Analog values are received via IEC 61850 GOOSE
messages sent from other devices.
6.5 Records
6.5.1 User-programmable fault reports
ACTUAL VALUES  RECORDS  USER-PROGRAMMABLE FAULT REPORTS
 USER-PROGRAMMABLE NEWEST RECORD
 FAULT REPORTS  NUMBER: 0
LAST CLEARED DATE:

 2002/8/11 14:23:57

CHAPTER 6: ACTUAL VALUES RECORDS
LAST REPORT DATE:

 2002/10/09 08:25:27
This menu displays the user-programmable fault report actual values. See the User-Programmable Fault Report section in
chapter 5 for information on this feature.
6.5.2 Event records

ACTUAL VALUES  RECORDS  EVENT RECORDS
 EVENT RECORDS EVENT: XXX
  XXX
 Date and time stamps
EVENT: 3 EVENT 3
 POWER ON   DATE: 2000/07/14
EVENT: 2 EVENT 3
 POWER OFF  TIME: 14:53:00.03405
EVENT: 1
 EVENTS CLEARED
The event records menu shows the contextual data associated with up to the last 1024 events, listed in chronological
order from most recent to oldest. When all 1024 event records have been filled, the oldest record is removed as a new
record is added. Each event record shows the event identifier/sequence number, cause, and date/time stamp associated
with the event trigger. See the COMMANDS  CLEAR RECORDS menu for clearing event records.
Only major output operands generate events, not every operand. Elements that assert output per phase, for example, log
operating phase output only without asserting the common three-phase operand event.
See also the system log (syslog) information in the previous chapter.
The event records are viewable in the software and in a web browser. The figure shows the event records in the software.
Figure 6-4: Event records viewed in EnerVista software
6

RECORDS CHAPTER 6: ACTUAL VALUES
To view events in a web browser:

1. Enter the IP address of the device.
To download an oscillography waveform:
1. Click the arrow icon in the Data column.

To display the event records page, press the Home pushbutton then the Event Record Tab pushbutton.
The newest event is always at the top.
Up and Down pushbuttons move the event selector up and down. When the selector is at the bottom of the display, the
Down pushbutton also scrolls the page, and similarly when the active selector is at the top of the display the Up
pushbutton scroll the page.
A selected event is highlighted in yellow and becomes active by pressing the Up or Down pushbutton.
There are two event markers, one green, the other cyan. To mark some an event, use the Up and Down pushbuttons to
select it (highlight in yellow), then press the green or cyan Mark Event Tab pushbutton. The mark color hides the selector
until the selector is moved. A field at the top of the page shows the interval between the two marks.
Figure 6-5: Event record
6.5.3 Oscillography

ACTUAL VALUES  RECORDS  OSCILLOGRAPHY
 OSCILLOGRAPHY FORCE TRIGGER? Range: No, Yes
  No
NUMBER OF TRIGGERS:
 0
AVAILABLE RECORDS:
 0
CYCLES PER RECORD:

 0
LAST CLEARED DATE:

 2000/07/14 15:40:16

CHAPTER 6: ACTUAL VALUES PRODUCT INFORMATION
This menu allows the user to view the number of triggers involved and number of oscillography traces available. The cycles
per record value is calculated to account for the fixed amount of data storage for oscillography. See the Oscillography
section of chapter 5 for details.
A trigger can be forced here at any time by setting “Yes” to the FORCE TRIGGER? command. See the COMMANDS  CLEAR
RECORDS menu for information on clearing the oscillography records.
To view a waveform:
2. Access Actual Values > Records > Oscillography in the EnerVista software.
3. In the window that opens, select the record number. The highest number is the most recent record (Newest Record
Number).
4. Click the Read button to get the waveform. When available, waveforms are displayed graphically, and otherwise error
messages display.
5. In the waveform window that opens, you can save the file, for example with the CFG extension.
6.6 Product information

6.6.1 Model information
ACTUAL VALUES  PRODUCT INFO  MODEL INFORMATION
 MODEL INFORMATION ORDER CODE LINE 1: Range: standard GE order code format
  B90-A00-AAA-A0A-A0A-
ORDER CODE LINE 2: Range: up to 20 alphanumeric characters

 A0A-A0A-A0A



 SERIAL NUMBER: Range: standard GE serial number format 6

ETHERNET MAC ADDRESS Range: standard Ethernet MAC address format
 000000000000
MANUFACTURING DATE: Range: YYYY/MM/DD HH:MM:SS


OPERATING TIME: Range: operating time in HH:MM:SS
 0:00:00
CT/ VT ADVANCED DIAG Range: Yes, No

 ACTIVE: No
LAST SETTING CHANGE: Range: YYYY/MM/DD HH:MM:SS

 1970/01/01 23:11:19
The order code, serial number, Ethernet MAC address, date and time of manufacture, and operating time are shown here.
The rear panel on the device contains similar information. The information is read-only in the software and modifiable on
the front panel. For example, the order code can be corrected using the front panel.
ETHERNET MAC ADDRESS — UR devices with firmware 7.0x and above have three Ethernet ports that can be used on three
networks. The MAC address displays for port 1. The MAC address for port 2 is one higher. The MAC address for port 3 is one
higher than port 2. In redundant mode, the MAC addresses for ports 2 and 3 are the same as port 2.

PRODUCT INFORMATION CHAPTER 6: ACTUAL VALUES
6.6.2 Firmware revisions

ACTUAL VALUES  PRODUCT INFO  FIRMWARE REVISIONS
 FIRMWARE REVISIONS B90 Relay Range: 0.00 to 655.35
  REVISION: 7.6x Revision number of the application firmware.
MODIFICATION FILE Range: 0 to 65535 (ID of the MOD FILE)

 NUMBER: 0 Value is 0 for each standard firmware release.
BOOT PROGRAM Range: 0.00 to 655.35

 REVISION: 7.01 Revision number of the boot program firmware.
FRONT PANEL PROGRAM Range: 0.00 to 655.35

 REVISION: 2.01 Revision number of front panel program firmware.
COMPILE DATE: Range: YYYY/MM/DD HH:MM:SS

 2016/09/15 04:55:16 Date and time when product firmware was built.
BOOT DATE: Range: YYYY/MM/DD HH:MM:SS

 2013/09/15 16:41:32 Date and time when the boot program was built.
FPGA PROGRAM Range: 0.00 to 655.35

 REVISION: 02.02 Revision number for FPGA.
FPGA DATE: Range: YYYY/MM/DD HH:MM:SS

 2016/09/15 16:41:32 Date and time when the FPGA was built.
The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been
installed.

ACTUAL VALUES  PRODUCT INFO  FIRMWARE REVISIONS
6  FIRMWARE REVISIONS
  B90 Relay
REVISION: 7.6x
Range: 0.00 to 655.35
Revision number of the application firmware.
MODIFICATION FILE Range: 0 to 65535 (ID of the MOD FILE)

 NUMBER: 0 Value is 0 for each standard firmware release.
BOOT PROGRAM Range: 0.00 to 655.35

 REVISION: 7.01 Revision number of the boot program firmware.
COMPILE DATE: Range: YYYY/MM/DD HH:MM:SS

 2017/06/15 04:55:16 Date and time when product firmware was built.
BOOT DATE: Range: YYYY/MM/DD HH:MM:SS

 2016/09/15 16:41:32 Date and time when the boot program was built.
GFP PROGRAM Range: 0.00 to 655.35

 REVISION: 7.60 Revision number of front panel program firmware.
GFP COMPILE DATE: Range: YYYY/MM/DD HH:MM:SS

 2017/03/03 12:58:00 Date/time when graphical front panel firmware built.
GFP BOOT PROGRAM Range: 0.00 to 655.35

 REVISION: 1.00 Revision number of panel boot program firmware.
GFP BOOT COMP. DATE: Range: YYYY/MM/DD HH:MM:SS

 2017/03/03 12:58:00 Date/time when panel boot program was built.
FPGA PROGRAM Range: 0.00 to 655.35

 REVISION: 02.02 Revision number for FPGA.
FPGA DATE: Range: YYYY/MM/DD HH:MM:SS

 2016/09/15 16:41:32 Date and time when the FPGA was built.

CHAPTER 6: ACTUAL VALUES PRODUCT INFORMATION
The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been
installed. The date format reflects the format specified for the clock and can vary from that shown here.

PRODUCT INFORMATION CHAPTER 6: ACTUAL VALUES

Chapter 7: Commands and targets
Commands and targets
This chapter outlines the Commands and Targets menus and self-tests/error messages. Commands related to the IEC
61850 protocol are outlined in the IEC 61850 section of the Settings chapter. Log/error messages for IEC 61850 are
outlined in the UR Family Communications Guide.
7.1 Commands menu
COMMANDS

 COMMANDS
  VIRTUAL INPUTS
 COMMANDS
  CLEAR RECORDS
 COMMANDS
  SET DATE AND TIME
 COMMANDS
  RELAY MAINTENANCE
 COMMANDS
  SECURITY
The commands menu contains relay directives intended for operations personnel. All commands can be protected from
unauthorized access via the command password; see the Security section of chapter 5 for details. The following flash
message appears after successfully command entry.
COMMAND
EXECUTED

COMMANDS MENU CHAPTER 7: COMMANDS AND TARGETS

COMMANDS  VIRTUAL INPUTS
 COMMANDS Virt Ip 1 Range: Off, On
 VIRTUAL INPUTS  Off
Virt Ip 2 Range: Off, On

 Off

Virt Ip 64 Range: Off, On
 Off
The states of up to 64 virtual inputs are changed here. The first line of the display indicates the ID of the virtual input. The
second line indicates the current or selected status of the virtual input. This status is a state off (logic 0) or on (logic 1).
7.1.2 Clear records

COMMANDS  CLEAR RECORDS
 COMMANDS CLEAR USER FAULT Range: No, Yes
 CLEAR RECORDS  REPORTS? No
CLEAR EVENT RECORDS? Range: No, Yes

 No
CLEAR OSCILLOGRAPHY? Range: No, Yes

 No
CLEAR UNAUTHORIZED Range: No, Yes

 ACCESS? No
CLEAR DIRECT I/O Range: No, Yes.

 COUNTERS? No Valid only for units with Direct Input/Output module.
CLEAR ALL RELAY Range: No, Yes

 RECORDS? No
This menu contains commands for clearing historical data such as the event records. Data is cleared by changing a
command setting to “Yes” and pressing the ENTER key. After clearing data, the command setting automatically reverts to
“No.”
7
7.1.3 Set date and time
COMMANDS  SET DATE AND TIME
 COMMANDS SET DATE AND TIME: Range: YYYY/MM/DD HH:MM:SS
 SET DATE AND TIME  2000/01/14 13:47:03
The date and time can be entered on the front panel keypad. The time setting is based on the 24-hour clock. The complete
date, as a minimum, must be entered to allow execution of this command. The new time and date take effect when the
ENTER key is pressed.
The clock also can be synchronized to the local computer time among several UR devices. Use the Synchronize Devices
entry in the Online Window area of the EnerVista software. (Click the button at the top of the window that opens.)
When the relay is synchronizing to an external time source such as PTP, IRIG-B, or SNTP, the manually entered time or the
manually synchronized time is over-written.
The timescale of the entered time is local time, including daylight savings time where and when applicable.

CHAPTER 7: COMMANDS AND TARGETS COMMANDS MENU
7.1.4 Relay maintenance

COMMANDS  RELAY MAINTENANCE
 COMMANDS PERFORM LAMP TEST? Range: No, Yes
 RELAY MAINTENANCE  No
PERFORM LCD TEST? Range: Off, Red, Green, Blue, White & Text Pattern,
 Off Black & Text Pattern, TV Test Pattern
PERFORM PUSHBUTTON Range: No, Yes

 TEST? No
UPDATE ORDER CODE? Range: No, Yes

 No
REBOOT RELAY? Range: No, Yes

 No
SERVICE COMMAND Range: 0, 101, 20511

 0
SAVE VOLATILE DATA? Range: No, Yes

 No
This menu contains commands for relay maintenance purposes. Commands for the lamp test and order code are
activated by changing a command setting to “Yes” and pressing the ENTER key. The command setting then automatically
reverts to “No.” The service command is activated by entering a numerical code and pressing the ENTER key.
Not all commands display in the software; use the front panel when required.
PERFORM LAMP TEST — Turns on all front panel LEDs and display pixels for a short duration.
PERFORM LCD TEST — This command detects either stuck-ON or stuck-OFF pixels (dead pixels) in the display screen on the
graphical front panel. RED/GREEN/BLUE is to display the solid background color in the whole screen. WHITE & TEXT
PATTERN shows the white background and black texts. BLACK & TEXT PATTERN shows the black background and white
texts. TV TEST PATTERN displays a standard television test pattern (SMPTE color bars). The test screen can be canceled by
pressing any pushbutton or after 30 seconds of inactivity.
PERFORM PUSHBUTTON TEST — This command tests the pushbuttons on the graphical front panel. During testing, press the
corresponding pushbutton according to the prompt text. A failure message is given if the expected action is not detected
in one minute. Holding the ESCAPE button for five seconds to interrupt the test sequence. The designated function of a
specific pushbutton is bypassed in the test.
UPDATE ORDER CODE — Use this command to read and update the order code, for example when hardware modules have
been changed inside the relay. It causes the relay to scan the backplane for the modules and update the order code to
match. All settings are defaulted with an update. When an update occurs, the following message displays and the relay
7
restarts.
UPDATING...
PLEASE WAIT
There is no impact if there have been no changes to the hardware modules. When an update does not occur, the ORDER
CODE NOT UPDATED message displays.
REBOOT RELAY — Restarts the relay so that changes to configuration settings can take effect. In most cases, if changes are
made to the configuration settings these changes do not take effect unless the relay is rebooted.
With the CyberSentry option, the Administrator and Operator roles can initiate the Reboot Relay command.
SERVICE COMMAND — Performs specific B90 service actions. Presently, there are two service actions available. Code
"20511" returns all settings to their factory default value and restarts the relay (then you re-enter IP address, restart, set
unit to "Programmed"). Code “101” is used to clear factory diagnostic information stored in the non-volatile memory. If a
code other than these two is entered, the command is ignored and no action is taken. Various self-checking diagnostics

TARGETS MENU CHAPTER 7: COMMANDS AND TARGETS
are performed in the background while the B90 is running, and diagnostic information is stored on the non-volatile
memory from time to time based on the self-checking result. Although the diagnostic information is cleared before the B90
is shipped from the factory, the user can want to clear the diagnostic information for themselves under certain
circumstances. For example, you clear diagnostic information after replacement of hardware. Once the diagnostic
information is cleared, all self-checking variables are reset to their initial state and diagnostics restart from scratch.
SAVE VOLATILE DATA — Saves this data to compact flash memory prior to shutdown. This allows the saved data to be as
recent as possible instead of relying on the periodic timer to save the data.
7.1.5 Security
COMMANDS  SECURITY
 SECURITY ADMINISTRATOR Range: Yes, No
  LOGOFF: No
ENGINEER Range: Yes, No

 LOGOFF: No
OPERATOR Range: Yes, No

 LOGOFF: No
CLEAR SECURITY DATA: Range: Yes, No

 No
With the CyberSentry option, this setting is available to enable or disable the following commands.
ADMINISTRATOR LOGOFF — Selecting ‘Yes’ allows the Supervisor to forcefully logoff an administrator session.
ENGINEER LOGOFF — Selecting ‘Yes’ allows the Supervisor to forcefully logoff an engineer session.
OPERATOR LOGOFF — Selecting ‘Yes’ allows the Supervisor to forcefully logoff an operator session.
CLEAR SECURITY DATA — Selecting ‘Yes’ allows the Supervisor to forcefully clear all the security logs and clears all the
operands associated with the self-tests.
7.2 Targets menu
TARGETS
7 
PHASE TOC4 Displayed only if targets for this element are active.
 OP: A B - Example shown.
DIGITAL ELEMENT 48: Displayed only if targets for this element are active.
 LATCHED Example shown.


A target enables the EnerVista UR Setup software to monitor automatically and display the status of any active target
messages of all the devices inserted into that site.
Each B90 element with a TARGET setting has a target message that when activated by its element is displayed in sequence
with any other currently active target messages in the TARGETS menu. In the example shown, the Phase TOC4 and Digital
Element 48 target settings are active and so have their targets displayed. The down arrow below the two elements
indicates that there can be other active elements beyond these two.
For more information, see the description of target messages in the next section, and the Introduction to Elements section
in the Settings chapter for instructions on TARGET setting.

CHAPTER 7: COMMANDS AND TARGETS TARGETS MENU
When no targets are active, the display reads NO ACTIVE TARGETS.
7.2.1 Target messages

When there are no active targets, the first target to become active causes the display to immediately default to that
message. If there are active targets and the user is navigating through other messages, and when the default message
timer times out (i.e. the keypad has not been used for a determined period of time), the display again defaults back to the
target message.
The range of variables for the target messages is described below. Phase information is included if applicable. If a target
message status changes, the status with the highest priority displays.
Table 7-1: Target message priority status
Priority Active status Description
1 OP element operated and still picked up
2 PKP element picked up and timed out
3 LATCHED element had operated but has dropped out
If a self test error is detected, a message appears indicating the cause of the error. For example UNIT NOT PROGRAMMED
indicates that the minimal relay settings have not been programmed.
7.2.2 Relay self-tests
7.2.2.1 Description
The relay performs a number of self-test diagnostic checks to ensure device integrity. The two types of self-tests (major
and minor) are listed in the following tables. When either type of error occurs, the Trouble LED Indicator turns on and a
target message displays. All errors record an event in the event recorder. Latched errors can be cleared by pressing the
RESET key, providing the condition is no longer present.
Major self-test errors also result in the following:
• The critical fail relay on the power supply module de-energizes
• All other output relays de-energize and are prevented from further operation
• The front panel In Service LED indicator turns off
• A RELAY OUT OF SERVICE event is recorded
To view error messages in EnerVista software:
1. Access Actual Values > Records > Event Records.
7
Messages display on the front panel with one or two lines of text. An example is as follows. In the tables that follow,
messages are grouped using the first line of text. For example, MAINTENANCE ALERT, then a row for 4L Discrepancy, then a
row for Bad IRIG-B Signal.
MAINTENANCE ALERT:
4L Discrepancy
MAINTENANCE ALERT:
Bad IRIG-B Signal
7.2.2.2 Major self-test error messages

The major self-test errors are outlined in this section.

Table 7-2: Major self-test errors

Error Latched? Description Test frequency Action
DIAGNOSTIC FAILURE ___:
Self Test Error No Internal recovery failure Upon recovery Extract a Service Report through UR
detected Setup software. Contact technical
support and supply details of the
failure code on the display.
EQUIPMENT MISMATCH:
2nd line detail No The number or type of On power up. Check all modules against the order
installed hardware modules Afterwards, the code, ensure they are inserted
does not match the order backplane is properly, and cycle control power. If a
code stored in the B90. An checked for missing module has intentionally been added
example is when a basic front cards every five or removed, refresh the order code
panel is installed and the seconds under Device Setup. If the problem
order code on the B90 persists, contact the factory.
expects a graphical front
panel.
FLEXLOGIC ERROR:
2nd line detail No A FlexLogic equation is Event driven, Finish all equation editing and use self
incorrect performed whenever tests to debug any errors.
FlexLogic equations
are modified
RAM FILESYSTEM FAIL:
Self-Test Error Yes The relay failed to create the On relay startup Contact factory service
RAM file system
SYSTEM FAILURE ___:
2nd line detail Yes Relay system failure detected Continuous Extract a Service Report through UR
Setup software. Contact technical
support and supply details of the
failure code on the display.
SYSTEM FAILURE:
Card F8L Yes This is an indication that the The recommendation is to replace this
DSP module has failed. The DSP. Extract a Service Report through
slot and DSP type are UR Setup software and provide it to GE
indicated in the message. customer service.
TO INSTALL SETTINGS:
CHECK LOG AND REBOOT Yes Certain settings require a A new CID is sent Restart relay
reboot to be applied, for and it includes
example DNP settings, IEC changes in settings
7 104 settings. After a CID file
was send to the relay, a
that require a reboot
to be
manual reboot of the relay is applied
required to apply those
settings that require a
reboot
UNIT NOT PROGRAMMED:
Check Settings No The PRODUCT SETUP  On power up and Program all settings and then set
INSTALLATION  RELAY whenever the PRODUCT SETUP  INSTALLATION
SETTINGS setting indicates PRODUCT SETUP  RELAY SETTINGS to “Programmed”
the B90 is not programmed  INSTALLATION
 RELAY SETTINGS
setting is altered
7.2.2.3 Minor self-test error messages

Most of the minor self-test errors can be disabled. See the settings in the User-programmable Self-tests section in chapter
5.

Table 7-3: Minor self-test errors

DIAGNOSTIC ALARM COP:
Self-test Error Yes This is a preliminary warning Extract a Service Report through UR
that transient errors were Setup software and provide it to GE
detected in the coprocessor. customer service
The relay remains operational
but some elements can
operate slightly delayed.
DIAGNOSTIC ALARM DSP:
Card F8L Yes This is a preliminary warning Extract a Service Report through UR
that there is something wrong Setup software and provide it to GE
with a DSP. The slot and DSP customer service
type is indicated in the
message.
DIAGNOSTICS FAILURE Yes This is a warning that there is Extract a Service Report through UR
something wrong with the Setup software and provide it to GE
DSP/coprocessor subsystem. customer service
The source of the problem is
unknown as there are
multiple contributors.
DIRECT DEVICE OFF:
COMM Path Incomplete No A direct device is configured Every second Check direct input and output
but not connected configuration and wiring
DOS PARTITION ALARM:
SELF-TEST ERROR There is a problem with the On relay power-up Contact the factory
Compact Flash memory in the and afterwards once
CPU module every 24 hours
LOW ON MEMORY:
with 2nd line detail Yes The relay periodically checks Every five seconds Contact the factory
the amount of free RAM
memory available and the
amount of free stack
available for each task
against pre-defined
thresholds. The second line of
the self-test indicates which
of the tests failed. It asserts
this self-test if those tests fail.
MAINTENANCE ALERT:
4L Discrepancy No A discrepancy has been Upon initiation of a Verify the state of the output contact
detected between the actual contact output state and contact the factory if the problem
7
and desired state of a change persists
latching contact output of an
installed type “4L” module
Bad IRIG-B Signal No A bad IRIG-B input signal has Monitored whenever Ensure the following:
been detected an IRIG-B signal is - The IRIG-B cable is properly
received connected.
- Proper cable functionality (that is,
check for physical damage or perform
a continuity test).
- The IRIG-B receiver is functioning.
- Check the input signal level (it can be
less than specification).
If none of these apply, then contact the
factory.


Bad PTP Signal No No PTP enabled port has Activated when no Ensure the following:
good PTP signal input acceptable signal is - The Ethernet cable(s) are properly
being received connected.
- At least one PTP grandmaster-
capable clock is functioning.
- If strict PP is enabled, that entire
network is PP compliant.
- The network is delivering PTP
messages to the relay.
Direct Ring Break No Direct input and output Every second Check direct input and output
settings are configured for a configuration and wiring
ring, but the connection is not
in a ring
FIRST ETHERNET FAIL Yes A link loss detection on an Check the connection
SECOND ETHERNET FAIL Ethernet port. The link loss is
THIRD ETHERNET FAIL due to unplugging the cable
or the switch port being
down.
Front Panel Trouble No The graphical front panel is Every second Contact the factory
not responsive for more than
five seconds. The relay is still
protecting, and the main CPU
is not affected by this self-
test.
GFP Version Mismatch No The graphical front panel Whenever Perform a UR firmware upgrade with
firmware revision is not connection is the graphical front panel connected to
synchronized with that of the established between the CPU module in the relay. It can be
CPU module in the relay the graphical front done using any communication
panel and the CPU interface (Ethernet or USB). This
module in the relay synchronizes the graphical firmware
revision with that of the relay. If trouble
persists, contact the factory.
GGIO Ind xxx oscill No A data item in a configurable Upon scanning of The “xxx” text denotes the data item
GOOSE data set is oscillating each configurable that has been detected as oscillating.
GOOSE data set Evaluate all logic pertaining to this
item.
Oscillatory GOOSE No A data item in a configurable Upon scanning of Evaluate all logic pertaining to this item
GOOSE data set is oscillating each configurable
GOOSE data set
Replace Battery Yes The battery is weak or not Every five seconds. Replace the battery as outlined in the
functioning. It powers the real The error message Maintenance chapter. To minimize the
time clock. This message displays after 60 disruption until battery replacement,
7 displays as Battery Fail in the
event records. When the
seconds if the
problem persists.
temporarily disable the battery fail
function under Settings > Product
battery weakness reaches a Setup > User-Programmable Self
critical level, the message Tests.
displays persistently on the
front panel and no front panel
key navigation is possible.
Setting Changed No Any device settings were On any setting Verify that the setting change was
changed over any available changes, when new legitimate and essential for proper
interface settings were written functioning of the protection and
to device control system


SFP MODULE x FAIL No A faulty small form-factor The web page "SFP Transceiver
pluggable port (SFP) or Information" described in the previous
unplugging of the SFP row applies for this self test as well. The
generates this self test "SFP Module Fail" has higher priority
message and it suppresses the "Ethernet Fail"
target message. The "SFP MODULE FAIL
FUNCTION" setting enables/disables
this self test. The target for this self test
is priority-based, with the third one
being the highest priority. For example,
if all three SFP modules fail, then the
third SFP target is activated. If the third
SFP module failure resolves, then the
second SFP target is activated.
SNTP Failure No The SNTP server is not Every 10 to 60 Check that Ethernet cable(s) are
responding seconds properly connected. Check that
configuration for the SNTP server
corresponds to the actual server
settings. Check connectivity to the
server (ping the server IP address).
Check that UR settings for both SNTP
servers are configured with different IP
addresses and port numbers.
PROTOTYPE FIRMWARE:
Self Test Error Seen until the build is tagged Seen on startup and Update firmware to either of these
as being 'release candidate' then continuous builds
or 'gold' build
RxGOOSE FAIL:
Missing messages No One or more RxGOOSE The self-test is Check GOOSE setup
messages are not being activated when no
received message is received
within the expected
time interval, which
is the time-to-live
time in the previous
message. This time
can be from
milliseconds to
minutes.
RxGOOSE OFFLINE:
COMM Path Incomplete No One or more RxGOOSE Event driven. The test Check GOOSE setup
messages are not responding is performed when a
device programmed
to receive GOOSE
7
messages stops
receiving. This can be
from 1 to 60
seconds, depending
on GOOSE packets.
SETTINGS SAVE ERROR:
Contact Factory Yes The relay failed to store the When a setting is Contact the factory
settings to the flash memory changed


STORAGE MEDIA ALARM:
Self Test Error No The CPU module fails to read On power up. Contact the factory
from or write to the Compact Afterwards, every
Flash (CF) card inside the time the CPU
module. The CF card stores accesses the CF card
certain non-volatile data, for reading or writing
such as event records,
oscillography and datalogger
records, fault report values,
and non-volatile actual
values. Settings are not stored
in CF and hence are
unaffected by this self-test.
SYSTEM EXCEPTION:
Press RESET key Yes Abnormal restart from Event driven Contact the factory
modules being removed or
inserted while the B90 is
powered-up, when there is an
abnormal DC supply, or as a
result of internal relay failure.
TEMP MONITOR:
OVER TEMPERATURE Yes The ambient temperature is Every hour Remove the B90 from service and
greater than the maximum install in a location that meets
operating temperature operating temperature standards
(+80°C)
UNIT NOT CALIBRATED:
with 2nd line DSP slot number Yes DSP module is not calibrated On relay startup The respective DSP module has to be
detail or calibration data is out of replaced, contact factory service
range
VOLTAGE MONITOR:
with 2nd line detail Yes The relay detected a problem Every five seconds Contact GE customer service
with the internal voltage rails
Power Supply 12V Low for longer than 25 seconds
Power Supply 12V High
Power Supply 5V Low
Power Supply 5V High
WRONG TRANSCEIVER:
Self Test Error Yes The type of SFP does not A web page "SFP Transceiver
match the CPU type. The SFP Information" is provided. This page
is a silver device that plugs displays the type of the SFP in it. This
7 into the rear of the CPU
module.
data is to be used with the CPU type to
know the cause of the problem.
T-type CPU = All ports support

fiber SFPs only
U-type CPU = Maintenance
port needs RJ45 SFP and the
other two ports fiber SFPs
V-type CPU = All ports support
RJ45 SFPs only
The consequence of an
incorrect SFP can range from
damage to the B90 to no
power information for the B90
on its web page (enter IP
address in a web browser,
then click the SFP
Transceiver Information —
only the type of SFP displays
and not power data).

Chapter 8: Application of settings
Application of settings
This chapter provides example(s) of use.
8.1 Overview
8.1.1 Introduction
This chapter provides an example of setting calculations for a sample bus. The selected example includes various bus
configurations to clarify a number of typical situations. Both the bus configuration and numerical data used are not meant
to reflect any specific utility practice or design standards.
It is also assumed that the CTs have been selected without considering a B90 application, but the UR settings are to be
calculated for proper relay application. The CT data used in this example are kept to a minimum and in a generic form. The
CT data does not reflect any particular notation or national standards.
The analysis provided in this chapter has been performed with the following goals:
• The limits of linear operation of the CTs considering zero remanent flux have been determined in order to select the
high breakpoint settings of the biased differential characteristic
• The limits of linear operation of the CTs considering a remanent flux of 80% have been determined in order to select
the low breakpoint settings of the biased differential characteristic
• Saturation of the CTs has been analyzed in order to select the higher slope of the biased differential characteristic and
the high set differential overcurrent setting
The analysis tools and safety margins applied are examples only and do not reflect any particular protection philosophy.
Typically, for the CT saturation related calculations, it is sufficient to consider the weakest (most prone to saturation) CT
connected to the bus and the total bus fault current combined with the longest time constant among all the circuits
connected to the bus. This chapter provides more detailed analysis (see the Slopes and High Set Threshold section) in order
to illustrate the idea of using setting groups to enhance the B90 performance when the bus configuration changes (see
the Enhancing Relay Performance section).
8.1.2 Sample busbar and data

The figure shows a double bus arrangement with North and South buses. This station has five circuits (C-1 through C-5)
and a tiebreaker (B-7). Circuit C-1 is connected to the North bus; circuits C-2, C-3 and C-4 can be routed to either bus via
switches S-1 through S-6; circuit C-5 can be connected to either bus via breakers B-5 and B-6.

OVERVIEW CHAPTER 8: APPLICATION OF SETTINGS
Figure 8-1: Sample bus configuration
C-3 C-5
NORTH BUS
B-1 S-1 S-3 S-5

B-5
CT-1 CT-7
CT-2 B-2 CT-3 B-3 CT-4 B-4 CT-5
B-7
CT-6
CT-8
B-6
S-2 S-4 S-6
SOUTH BUS
C-1 C-2 C-4
836731A2.CDR
The table shows the assumed short circuit contributions of the connected circuits and their DC time constants.
Table 8-1: Basic fault data of the connected circuit
Circuit IFAULT (kA) TDC (ms)
C-1 0.00 N/A
C-2 0.00 N/A
C-3 6.00 5
C-4 5.00 30
C-5 3.00 40
The basic CT data is presented in the following table. The magnetizing characteristics of the three different types of CTs
used in this example are shown in the following figure.
Table 8-2: Basic CT data
CT Ratio Vsat (V) RCTsec () Leads (m)
CT-1 600:5 144 0.34 210
CT-2 600:5 144 0.34 205
8 CT-3 1200:5 288 0.64 200
CT-4 1000:5 240 0.54 200
CT-5, CT-6 1000:5 240 0.54 180
CT-7, CT-8 1200:5 288 0.64 200

CHAPTER 8: APPLICATION OF SETTINGS ZONING AND DYNAMIC BUS REPLICA
Figure 8-2: Approximate CT magnetizing characteristics
836732A4.CDR
8.2 Zoning and dynamic bus replica

8.2.1 North bus zone
With reference to the following diagram, the North bus differential zone is bounded by the following CTs: CT-1, CT-2 (if S-1
closed), CT-3 (if S-3 closed), CT-4 (if S-5 closed), CT-5 and CT-8. The North bus protection is to operate the following
breakers: B-1, B-2 (if S-1 closed), B-3 (if S-3 closed), B-4 (if S-5 closed), B-5 and B-7.

ZONING AND DYNAMIC BUS REPLICA CHAPTER 8: APPLICATION OF SETTINGS
Figure 8-3: North bus zone
C-3 C-5
NORTH BUS
B-1 S-1 S-3 S-5

B-5
CT-1 CT-2 B-2 CT-4 B-4 CT-7

CT-3 B-3
CT-5
B-7
CT-6
CT-8
B-6
S-2 S-4 S-6
SOUTH BUS
C-1 C-2 C-4

836733A1.CDR
8.2.2 South bus zone

The South bus differential zone is bounded by the following CTs: CT-2 (if S-2 closed), CT-3 (if S-4 closed), CT-4 (if S-6 closed),
CT-6 and CT-7. The South bus protection is to operate the following breakers: B-2 (if S-2 closed), B-3 (if S-4 closed), B-4 (if S-
6 closed), B-6 and B-7.
Figure 8-4: South bus zone
C-3 C-5
NORTH BUS
B-1 S-1 S-3 S-5

B-5
CT-1 CT-2 B-2 CT-4 B-4 CT-7

CT-3 B-3
CT-5
8
B-7
CT-6
CT-8
B-6
S-2 S-4 S-6
SOUTH BUS
C-1 C-2 C-4

836734A1.CDR

CHAPTER 8: APPLICATION OF SETTINGS BIASED CHARACTERISTIC BREAKPOINTS
8.3 Biased characteristic breakpoints

8.3.1 Description
The limits of linear operation of the CTs need to be found in order to set the breakpoints of the biased differential
characteristic. The settings for the North and South bus relays are analyzed simultaneously from this point on as the two
differential zones share some CTs and the results of computations apply to both the relays.
For microprocessor-based relays it is justified to assume the burden of the CTs to be resistive. The limits of the linear
operation of a CT, neglecting the effects of the DC component and residual magnetism, can be approximated as follows:
Eq. 8-1
where
Imax is the maximum secondary current transformed without saturation (AC component only, no residual magnetism),
Rs is the total burden resistance
Vsat is the saturation voltage of the CT
The total burden resistance depends on both the fault type and connection of the CTs. For single-line-to-ground faults and
CTs connected in Wye, the burden resistance is calculated as:
Eq. 8-2
where
Rlead is the lead resistance (one way, hence the factor of 2)
RCTsec is the secondary CT resistance
Rrelay is the relay input resistance
Assuming 0.003 /m lead resistance and approximating the B90 input resistance for the 5A input CTs as 0.2 VA / (5 A)2 or
0.008 , the limits of the linear operation of the CTs have been calculated and presented in the Limits of Linear Operations
of the CTs table.
8.3.2 High breakpoint

As an external fault can happen on any of the connected circuits, threatening saturation of any of the CTs, take the
minimum value of the linear operation limit as the HIGH BPNT setting. The limit of linear operation that neglects both the
residual magnetism and the effect of the DC component should be the base for setting the higher breakpoint of the biased
differential characteristic.
The B90 requires the breakpoints to be entered as ‘pu’ values. The relay uses the largest primary current of the CTs
bounding the bus differential zone as a base for the pu settings. Both the North and South buses have the largest primary
current of the CTs of 1200 A (CT-7 and CT-8), thus upon configuration of the relays, 1200 A is automatically selected as
base for the pu quantities. With a given Ibase current, the limits of linear operation have been recalculated to pu values as
follows:
8
Eq. 8-3

SLOPES AND HIGH SET THRESHOLD CHAPTER 8: APPLICATION OF SETTINGS
Table 8-3: Limits of linear operation of the CTS

CT Rs () Imax (A sec) Imax (pu) Imax (pu)
(no remanence) (80% remanence)
CT-1 1.61 89.55 8.96 1.79
CT-2 1.58 91.25 9.13 1.83
CT-3 1.85 155.84 31.17 6.23
CT-4 1.75 137.30 22.88 4.58
CT-5, CT-6 1.63 147.42 24.57 4.91
CT-7, CT-8 1.85 155.84 31.17 6.23
The third and fourth columns of the table have the following significance.
If an external fault occurs on circuit C-1, then CT-1 carries the fault current. As the fault current is higher than any of the
other currents, the current supplied by CT-1 is used as the restraint signal. CT-1 is guaranteed to saturate if the current
exceeds 89.55 A secondary, or 17.9 times its rated current, or 8.96 pu of the bus differential zone. Consequently,
considering CT-1, the value of 8.96 pu is used as the higher breakpoint of the characteristic.
Considering CTs that can be connected (depending on the positions of the switches) to the North bus, the HIGH BPNT for the
North bus zone is selected as the minimum of (8.96, 9.13, 31.17, 22.88, 24.57, 31.17), or 8.96 pu.
Considering CTs that can be connected (depending on the positions of the switches) to the South bus, the HIGH BPNT for the
South bus zone is selected as the minimum of (9.13, 31.17, 22.88, 24.57, 31.17), or 9.13 pu.
8.3.3 Low breakpoint

The DC component in the primary current can saturate a given CT even with the AC current below the suggested value of
the higher breakpoint. The relay copes with this threat by using the Saturation Detector and applying a 2-out-of-2
operating principle upon detecting saturation.
The residual magnetism (remanence) left in the core of a CT can limit the linear operation of the CT significantly. It is
justified to assume that the residual flux can be as high as 80% of the saturation level leaving only 20% to accommodate
the flux component created by the primary current. This phenomenon can be reflected by reducing the saturation voltage
in the calculations by the factor of 100% / 20%, or 5. This, in turn, is equivalent to reducing the limit of linear operation by
the factor of 5, hence the last column in the Limits of Linear Operations of the CTs table.
For example, if the residual flux left in the core of the CT-1 is as high as 80% of its saturation level, the CT saturates at 17.92
A secondary, or 3.58 times its rated current, or at 1.79 pu of the bus differential zone.
The reduced limit of linear operation is used as the lower breakpoint of the biased differential characteristic (the LOW BPNT
setting). In this way the interval spanning from the lower to higher breakpoints covers the indistinct area of possible
saturation due to the random factor of residual magnetism.
The LOW BPNT is set at 1.79 pu for the North bus zone, and at 1.83 pu for the South bus zone.
A combination of very high residual magnetism and a DC component with a long time constant can saturate a given CT
even with the AC current below the suggested value of the lower breakpoint. The relay copes with this threat by using a 2-
8 out-of-2 operating mode for low differential currents.
8.4 Slopes and high set threshold

8.4.1 Description
To set the higher slope and threshold of the high set (unbiased) differential operation, external faults must be analyzed.
Consider an external fault for the North bus relay. It is justified to assume bus configurations that give maximum stress to
the maximum number of CTs. For this purpose we assume the tie breaker, B-7 closed; all the circuitry capable of supplying
the fault current to be in service; moreover, they are connected to the South bus in order to analyze the CT-7 and CT-8
carrying the fault current.

CHAPTER 8: APPLICATION OF SETTINGS SLOPES AND HIGH SET THRESHOLD
8.4.2 External faults on C-1

The following table presents the results of analysis of an external fault on circuit C-1 (C-1 is connected to the North bus; C-
3, C-4, and C-5 are connected to the South bus).
For security reasons, it has been assumed that the fault current being a sum of several contributors (C-3, C-4, and C-5 in
this case) has a time constant of the DC component of the maximum among the time constants of the contributors. The
fault current is supplied from circuits C-3, C-4, and C-5 connected to the South bus, thus through CT-3, CT-4, and CT-6. The
current passes through the tie breaker threatening saturation of CT-7 and CT-8.
By comparing the secondary currents (column 3 in the table below) with the limits of linear operation for the CTs (column 4
in the Limits of Linear Operations of the CTs table earlier), it is concluded that CT-1 will saturate during this fault, producing
a spurious differential signal for the North bus zone differential protection. All other CTs do not saturate due to the AC
components. The amount of the spurious differential current (magnetizing current of CT-1) can be calculated using the
burden, magnetizing characteristic and primary current of the noted CT by solving the following equations:
Eq. 8-4
For Is = 116.67 A, Rs = 1.61 Ω and the characteristic shown earlier in the Approximate CT Magnetizing Characteristics
figure, the solution is Imagnetizing = 29.73 A, Irelay = 112.8 A.
The magnetizing current of the saturated CT-1 appears to the differential element protecting the North bus as a
differential signal of 29.73 A, while the restraint signal is the maximum of the bus currents (112.8 A in this case).
Consequently, the higher slope of the characteristic should not be lower than 29.73 A / 112.8 A, or 26%, and the pickup of
the high set differential elements should not be lower than 29.73 A, or 2.97 pu.
The CTs identified as operating in the linear mode as far as the AC components are considered can, however, saturate due
to the DC components. Saturation does not occur if Vsat > Is x Rs x (1 +  x Tdc), where  is radian system frequency (2f).
If the above condition is violated, CT time-to-saturate for a full DC saturation can be estimated as follows. The CT
saturation factor Ks capability curve is defined as
Eq. 8-5
where
T1 is a primary system time constant
T2 is the secondary CT time constant, which can be estimated by the following equation:
Eq. 8-6
where
N is the CT ratio
Vs is the CT voltage at 10 A exciting current obtained from the CT excitation curve 8
CT limiting factor KS_LIM is defined by the following equation:
Eq. 8-7
where
Ip is the maximum CT primary fault current
The figure illustrates the Ks CT saturation capability curve and KS_LIM limiting factor.

SLOPES AND HIGH SET THRESHOLD CHAPTER 8: APPLICATION OF SETTINGS
Figure 8-5: Determining CT time-to-saturate
CT time-to-saturate (tSAT) is determined as a projection of the intersection of the Ks CT saturation capability curve and
KS_LIM CT limiting factor, as shown in the figure.
Practically, CT time-to-saturate can be obtained by either of the following methods:
• Method 1 — Download the "CT Time-to-Saturate Estimator.xlsm" spreadsheet from the GE Multilin web site, located
under Support > Support Documents > B90 Low Impedance Bus Differential System. Enter the required system and CT
parameters to obtain the CT time-to-saturate.
• Method 2
– Define several time instances t1, t2...tn
– Use equation 8-5 to calculate the corresponding KS1, KS2…KSn
– Calculate KS_LIM using equation 8-7
– Compare each KS value with KS_LIM. If KS at the given time instance ti is less than KS_LIM, it means that true tSAT is
greater than ti, otherwise it is less than ti
Columns 6 and 7 of the table below summarize the DC saturation threat for the fault on C-1. CT-4, CT-6, CT-7, and CT-8 can
saturate due to the DC components and can generate spurious differential signal for both the North and South bus relays
depending on the bus configuration. The saturation does not occur before 5.02 ms and is detected by the Saturation
Detector.
The transient saturation of the CTs due to the DC component can be neglected when setting the slopes of the
characteristic as the saturation is detected and the relay uses the current directional principle. It must, however, be taken
into account when setting the high set (unbiased) differential element.
8 Table 8-4: External fault calculations on C-1

CT IFAULT (kA) IFAULT (A sec) TDC (ms) AC saturation DC saturation tSAT (ms)
CT-1 14.0 116.67 40 Yes Yes 5.02
CT-2 0 0.00 N/A No No N/A
CT-3 6.0 25.00 5 No No N/A
CT-4 5.0 25.00 30 No Yes 26.37
CT-6 3.0 15.00 40 No Yes 61.50
CT-7, CT-8 14.0 58.33 40 No Yes 9.44

CHAPTER 8: APPLICATION OF SETTINGS SLOPES AND HIGH SET THRESHOLD

3, C-4 and C-5 are connected to the South bus).
By comparing the secondary currents (column 3 in the following table) with the limits of linear operation for the CTs
(column 4 shown earlier in the Limits of Linear Operations of the CTs table) it is concluded that CT-2 will saturate during this
fault producing a spurious differential signal. All other CTs do not saturate due to the AC components. The amount of the
spurious differential current (magnetizing current of CT-2) can be calculated using the burden, magnetizing characteristic,
and the primary current of the said CT.
For Is = 116.67 A, Rs = 1.23  and the characteristic shown earlier in the Approximate CT Magnetizing Characteristics
figure, the solution is Imagnetizing = 27.69 A, Irelay = 113.3 A.
The magnetizing current of the saturated CT-2 appears to the differential element protecting the North bus as a
differential signal of 27.69 A, while the restraint signal is the maximum of the bus currents (113.3 A). Consequently, the
higher slope of the characteristic should not be lower than 27.69 A / 113.3 A, or 24% and the pickup of the high-set
differential elements should not be lower than 27.69 A, or 2.77 pu.
Columns 6 and 7 of the following table summarize the DC saturation threat for the fault on C-2. CT-4, CT-6, CT-7, and CT-8
can saturate due to the DC components and can generate spurious differential signal for both the North and South bus
relays depending on the bus configuration. The saturation does not occur before 5.06 ms and is detected by the Saturation
Detector.
Table 8-5: External fault calculations on C-2
CT-2 14.0 116.67 40 Yes Yes 5.06
CT-3 6.0 25.00 5 No No N/A
CT-4 5.0 25.00 30 No Yes 26.37
CT-6 3.0 15.00 40 No Yes 61.50
CT-7, CT-8 14.0 58.33 40 No Yes 9.44

4 and C-5 are connected to the South bus).
in the Limits of Linear Operations of the CTs table shown earlier), it is concluded that none of the CTs saturate due to the AC
currents during this fault.
Columns 6 and 7 of the table below summarize the DC saturation threat for the fault on C-3. CT-3, CT-4, CT-6, CT-7, and CT-
8 can saturate due to the DC components and can generate a spurious differential signal for both the North and South bus
relays depending on the bus configuration. The saturation does not occur before 23.68 ms and is detected by the
Saturation Detector. 8
Table 8-6: Calculations for the external faults on C-3
CT-3 8.0 33.33 40 No Yes 23.68
CT-4 5.0 25.00 30 No Yes 26.37
CT-6 3.0 15.00 40 No Yes 61.50
CT-7, CT-8 8.0 33.33 40 No Yes 23.68

BUS DIFFERENTIAL SETTINGS CHAPTER 8: APPLICATION OF SETTINGS

can saturate due to the DC components and can generate a spurious differential signal for both the North and South bus
relays depending on the bus configuration. The saturation does not occur before 10.03 ms and is detected by the
Saturation Detector.
CT-3 6.0 25.00 5 No No N/A
CT-4 9.0 45.00 40 No Yes 10.03
CT-6 3.0 15.00 40 No Yes 61.50
CT-7, CT-8 9.0 37.50 40 No Yes 22.23

can saturate due to the DC components and can generate a spurious differential signal for both the North and South bus
relays depending on the bus configuration. The saturation does not occur before 9.45 ms and is detected by the Saturation
Detector.
CT-3 6.0 25.00 5 No No N/A
CT-4 5.0 25.00 30 No Yes 26.37
8 CT-5 11.0 55.00 30 No Yes 9.45
CT-7, CT-8 11.0 45.83 30 No Yes 11.54
8.5 Bus differential settings

8.5.1 Description
Taking the previous analysis from this chapter into account, the settings have been calculated as follows.

CHAPTER 8: APPLICATION OF SETTINGS ENHANCING RELAY PERFORMANCE
Table 8-9: North bus differential protection settings

Setting Value Comments
PICKUP 0.1 pu Default value. Lower or higher values can be entered upon security/dependability
requirements. The pu value is for the base of 1200A. This means the actual pickup is 120 A
primary.
LOW SLOPE 25% Default value. Lower or higher values can be entered upon security/dependability
requirements.
LOW BPNT 1.79 pu None of the CTs saturate for AC currents below 1.79 pu even with 80% remanence. The DC
component, however, combined with the remanence can saturate some CTs even for currents
below 1.79 pu. The B90 copes with saturation using the current directional principle.
HIGH SLOPE 60% Default value. Lower or higher values can be entered upon security/dependability
requirements. The value of 60% ensures that the differential characteristic alone (without the
directional principle) work correctly under AC saturation of the CTs (26% of spurious
differential during the fault on C-1 saturating CT-1).
HIGH BPNT 8.96 None of the CTs saturate for AC currents below 8.96 pu. The DC component, however, can
saturate some CTs even for currents below 8.96 pu. The B90 copes with saturation using the
current directional principle.
HIGH SET 5.94 The maximum spurious differential current is 2.97 pu. Due to limited accuracy of analysis and
the effect of DC saturation a security factor of 2 has been adopted. The highest internal fault
current is 14kA, or 11.67 pu giving a good chance to clear a number of faults by the unbiased
differential operation.
Table 8-10: South bus differential protection settings

Setting Value Comments
PICKUP 0.1 pu Default value. Lower or higher values can be entered upon security/dependability
requirements. The pu value is for the base of 1200A. This means the actual pickup is 120 A
primary.
LOW SLOPE 25% Default value. Lower or higher values can be entered upon security/dependability
requirements.
LOW BPNT 1.83 pu None of the CTs saturate for AC currents below 1.83 pu even with 80% remanence. The DC
component, however, combined with the remanence can saturate some CTs even for
currents below 1.83 pu. The B90 copes with saturation using the current directional principle.
HIGH SLOPE 60% Default value. Lower or higher values can be entered upon security/dependability
requirements. The value of 60% ensures that the differential characteristic alone (without the
directional principle) work correctly under AC saturation of the CTs (24% of spurious
differential during the fault on C-2 saturating CT-2).
HIGH BPNT 9.13 pu None of the CTs saturate for AC currents below 9.13 pu. The DC component, however, can
saturate some CTs even for currents below 9.13 pu. The B90 copes with saturation using the
current directional principle.
HIGH SET 5.54 The maximum spurious differential current is 2.77 pu. Due to limited accuracy of analysis and
the effect of DC saturation a security factor of 2 has been adopted. The highest internal fault
current is 14kA, or 11.67 pu giving a good chance to clear a number of faults by the unbiased
differential operation.
8.6 Enhancing relay performance 8

8.6.1 Using setting groups
In the example of the South bus, CT-2 is the weakest (most prone to saturation) CT dictating values of some settings.
However, CT-2 may not be a part of the South bus protection zone if the S-2 switch is opened. As the position of the switch
must be provided for the dynamic bus replica, the status of the switch can be re-used to control the setting groups and
apply more sensitive settings if the weakest CT is not part of the bus zone at a given time. For example, if the S-2 switch is
opened while the S-6 switch is closed, the CT-4 becomes the weakest CT connected to the South bus. The higher
breakpoint (HIGH BPNT) could be increased to 22.88 pu (fourth column of the Limits of Linear Operations of the CTs table).

ENHANCING RELAY PERFORMANCE CHAPTER 8: APPLICATION OF SETTINGS
The lower breakpoint (LOW BPNT) could be increased to 4.58 pu (fifth column of the Limits of Linear Operations of the CTs
table). The higher slope (HIGH SLOPE) could be decreased as no AC saturation is possible for the South bus CTs (see the
external fault calculation tables for each circuit).
The concept could be implemented by using:
• FlexLogic to process the status signals in order to identify the weakest CT
• Setting Groups to switch dynamically from one setting group to another (adaptive settings)
This approach can be extended for buses that do not require the dynamic bus replica mechanism. This can include
approximation of the total bus fault current using positions of all switches and breakers and optimizing the settings
depending on the amount of stress imposed on the CTs in any particular bus configuration.

Chapter 9: Theory of operation
Theory of operation
This chapter outlines advanced information on operation.
9.1 Introduction
9.1.1 Bus differential protection
The figure shows that input currents defining (through the dynamic bus replica) the bus differential zone are received by
the B90 from current transformers (CTs) associated with the power system.

INTRODUCTION CHAPTER 9: THEORY OF OPERATION
Figure 9-1: Bus differential protection block diagram
Measuring Unit Unbiased Differential

Unit
1 2 3
i1 I1
Differential
Unbiased
DIFUNB
4
i2 I2
ID
Ratio Matching and Scaling Differential 6
Current
Phasor Estimation
i3 I3
Pre-Filtering
input currents
DIFL
DIF1
5 7
IR
Restraining
DIFH
DIF2
Current
8 L
iN IN O DIFBIASED
G
I
C
Directional
DIR
Element
10
Saturation SAT
Detector
11
9 Biased Differential
Unit
836723A1.CDR
The currents are digitally pre-filtered (Block 1) in order to remove the decaying DC components and other signal
distortions.
The filtered input signals are brought to a common scale taking into account the transformation ratios of the connected
CTs (Block 2). See the Dynamic Bus Replica section in this chapter.
Phasors of the differential zone currents are estimated digitally (Block 3), and the differential (Block 4) and restraining (Block
5) signals are calculated. See the Differential Principle section.
The magnitude of the differential signal is compared with a threshold, and an appropriate flag indicating operation of the
unbiased bus differential protection is produced (Block 6).
The magnitudes of the differential and restraining currents are compared and two auxiliary flags that correspond to two
specifically shaped portions of the differential operating characteristic (DIF1 and DIF2) are produced (blocks 7 and 8). The
characteristic is split in order to enhance performance of the relay by applying diverse security measures for each of the
regions. See the Differential Principle section.
The directional element (Block 10) supervises the biased differential characteristic when necessary. The current directional
comparison principle is used that processes phasors of all the input currents as well as the differential and restraining
currents. See the Directional Principle section.
The saturation detector (Block 9) analyzes the differential and restraining currents as well as the samples of the input
9 currents. This block sets its output flag upon detecting CT saturation. See the Saturation Detector section.
The output logic (Block 11) combines the differential, directional, and saturation flags into the biased differential operation
flag. The applied logic enhances performance of the relay while keeping an excellent balance between dependability/
speed and security. See the Output Logic and Examples section.

CHAPTER 9: THEORY OF OPERATION DYNAMIC BUS REPLICA
9.2 Dynamic bus replica

9.2.1 Dynamic bus replica mechanism
The bus differential zones of the B90 allow for protecting bus sections that include circuits that are switchable between
different sections. Proper relay operation is achieved by associating a status signal with each input current. This
mechanism is referred to as a dynamic bus replica.
The dynamic bus zone is programmed as a number of CT input–status–direction entries.
The status signal of a given CT input–status pair of the dynamic bus replica is a FlexLogic operand created to indicate
whether or not the associated circuit (current) is connected to the protected bus zone. Normally, the status signals are to
be created from input contacts wired to appropriate auxiliary contacts of isolator switches or breakers.
9.2.2 CT ratio matching

The B90 allows for using CTs with various rated secondary currents and transformation ratios. Scaling to a common base
is performed internally by the relay. The maximum allowable ratio mismatch is 32:1. For proper setting of the differential
characteristic, it is imperative to understand the common base used by the relay.
The B90 scales the secondary currents to the maximum primary current among the CTs defining a given bus differential
zone: 1 per unit corresponds to the highest rated primary current.
The scaling base is selected automatically by the relay during the configuration phase and is not affected by the dynamic
aspect of the bus differential zone. This means that even though the circuit containing the CT with the maximum rated
primary current is not connected to a given bus zone at a given time, the scaling base does not change.
9.2.2.1 Example 1
Assume that the CTs installed in the circuit defining the BUS ZONE 1 have the following ratings:
• 1A CT: 600:5
• 1B CT: 500:1
• 1C CT: 600:5
• 1D CT: 1000:5
• 1E CT: 500:1
• 1F CT: 600:5
The maximum of 600, 500, 600, 1000, 500, and 600 is 1000 A, which is selected as the base upon configuration of the BUS
ZONE 1. 1 per unit (pu) represents 1000 A primary.
9.3 Differential principle

9.3.1 Biased differential characteristic
The B90 uses a dual-slope dual-breakpoint operating characteristic as shown in the following figure.
The PICKUP setting is provided to cope with spurious differential signals when the bus carries a light load and there is no
effective restraining signal. 9
The first breakpoint (LOW BPNT) is provided to specify the limit of guaranteed linear operation of the CTs in the most
unfavorable conditions, such as high residual magnetism left in the magnetic cores or multiple autoreclosure shots. This
point defines the upper limit for the application of the first slope (LOW SLOPE).
The second breakpoint (HIGH BPNT) is provided to specify the limits of operation of the CTs without any substantial
saturation. This point defines the lower limit for the application of the second slope (HIGH SLOPE).

DIFFERENTIAL PRINCIPLE CHAPTER 9: THEORY OF OPERATION
Figure 9-2: Biased operating characteristic
|Id|
differential OPERATE
HIGH
SLOPE
BLOCK
LOW SLOPE Ir
PICKUP
HIGH BPNT
LOW BPNT restraining
836720A1.cdr
The higher slope used by the B90 acts as an actual percentage bias regardless of the value of the restraining signal. This is
so because the boundary of the operating characteristic in the higher slope region is a straight line intersecting the origin
of the ‘differential - restraining’ plane. The advantage of having a constant bias specified by the HIGH SLOPE setting creates
an obstacle of a discontinuity between the first and second slopes. This is overcome by using a smooth approximation
(cubic spline) of the characteristic between the lower and higher breakpoints. Consequently, the characteristic ensures
• A constant percentage bias of LOW SLOPE for restraining currents below the lower breakpoint of LOW BPNT,
• A constant percentage bias of HIGH SLOPE for restraining currents above the higher breakpoint of HIGH BPNT, and
• A smooth transition from the bias of LOW SLOPE to HIGH SLOPE between the breakpoints
9.3.2 Differential and restraining currents

The differential current is produced as a sum of the phasors of the input currents of a differential bus zone taking into
account the status signals of the currents, for example applying the dynamic bus replica of the protected zone. The
differential current is scaled to the maximum rated primary current. The scaling must be taken into account when setting
the PICKUP value of the biased differential characteristic and the HIGH SET operating point of the unbiased differential
function.
The restraining current is produced as a maximum of the magnitudes of the phasors of the zone input currents taking into
account the status signals of the currents, for example applying the dynamic bus replica of the protected bus zone. The
restraining current is scaled to the maximum rated primary current. The scaling must be taken into account when setting
the breakpoints of the biased differential characteristic.
The “maximum of” definition of the restraining signal biases the relay toward dependability without jeopardizing security
as the relay uses additional means to cope with CT saturation on external faults. An additional benefit of this approach is
that the restraining signal always represents a physical — compared to an “average” or “sum of” — current flowing through
the CT that is most likely to saturate during given external fault. This brings more meaning to the breakpoint settings of the
9 operating characteristic.
The following example is provided with respect to the breakpoint settings.
9.3.2.1 Example 2
Proceed with the previous example and assume that taking into account the relevant factors such as properties of the CTs
themselves, resistance of the leads, and burden of the CTs, the following primary currents are guaranteed to be
transformed without significant saturation:

CHAPTER 9: THEORY OF OPERATION DIFFERENTIAL PRINCIPLE
• 1A CT: 6.0 kA
• 1B CT: 7.5 kA
• 1C CT: 5.0 kA
• 1D CT: 13.0 kA
• 1E CT: 8.0 kA
• 1F CT: 9.0 kA
As having the lowest primary current guaranteeing operation without saturation, the CT associated with the 1C input is
most exposed to saturation. During an external fault on the 1C circuit, the 1C CT carries the fault current contributed by
potentially all the remaining circuits. The fault current is higher than any contributing current, and therefore, the current of
the 1C CT becomes the restraining signal for the biased differential characteristic for external faults on the 1C circuit.
Consequently, the higher breakpoint of the differential characteristic (HIGH BPNT) needs to be set no higher than 5000 A,
where 1000 A = 5 pu (1000 A is the base unit as outlined in the previous the example).
The same approach applies to the setting of the lower breakpoint, LOW BPNT.
9.3.3 Enhanced security

To enhance the performance of the B90, the differential characteristic is divided into two regions having diverse operating
modes, as shown in following figure.
The first region applies to comparatively low differential currents and has been introduced to deal with CT saturation on
low-current external faults. Certain distant external faults can cause CT saturation due to extremely long time constants of
the DC component or multiple autoreclosure shots. The saturation, however, is difficult to detect in such cases. Additional
security via the “directional check” is permanently applied to this region without regard to the saturation detector.
Figure 9-3: Two regions of differential character
Region 2
(high differential
differential
currents)
Region 1
(low differential
currents)
restraining
836725A1.CDR
The second region includes the remaining portion of the differential characteristic and applies to comparatively high
differential currents. If, during an external fault, the spurious differential current is high enough so that the differential-
restraining current trajectory enters the second region, then saturation is guaranteed to be detected by the saturation
detector.
9
The B90 operates in the 2-out-of-2 mode in the first region of the differential characteristic. Both differential and
directional principles (Differential Principle and Directional Principle) must confirm an internal fault in order for the biased
differential element to operate.

DIRECTIONAL PRINCIPLE CHAPTER 9: THEORY OF OPERATION
The relay operates in the dynamic 1-out-of-2 / 2-out-of-2 mode in the second region of the differential characteristic. If the
saturation detector (see the Saturation Detector section) does not detect CT saturation, the differential protection principle
alone is capable of operating the biased differential element. If CT saturation is detected, both differential and directional
principles must confirm an internal fault in order for the biased differential element to operate.
Because of diverse operating modes in the first and second regions of the differential characteristic, the user gains double
control over the dependability and security issues. The first level includes slopes and breakpoints of the characteristic with
regard to the amount of the bias. The second level includes control over the split between the first and second regions of
the characteristic.
9.4 Directional principle

9.4.1 Current directional protection
For better security, the B90 uses the current directional protection principle to dynamically supervise the main current
differential function. The directional principle is in effect permanently for low differential currents (region 1 in the Two
Regions of Differential Characteristic figure) and is switched on dynamically for large differential currents (region 2 in the
same figure) by the saturation detector (see the Saturation Detector section) upon detecting CT saturation.
The directional principle responds to a relative direction of the fault currents. This means that a reference signal, such as
bus voltage, is not required. The directional principle declares that
• If all of the fault currents flow in one direction, the fault is internal, or
• If at least one fault current flows in an opposite direction compared with the sum of the remaining currents, the fault is
external
The directional principle is implemented in two stages.
First, based on the magnitude of a given current, it is determined whether the current is a fault current. If so, its relative
phase relation has to be considered. The angle check must not be initiated for the load currents as the direction is out of
the bus even during internal faults. The auxiliary comparator of this stage applies an adaptable threshold. The threshold is
a fraction of the restraining current. The current from a particular feeder is used for bus directional comparison if its
magnitude is greater than K × Irestraint or it is greater than 2 times its CT rating. For bus zones with two feeders, K = 0.2. For
bus zones with three to six feeders, K = 0.8 / (N – 1). For bus zones with more than six feeders, K = 0.16.
Second, for the selected fault currents, the phase angle between a given current and the sum of all the remaining currents
is checked. The sum of all the remaining currents is the differential current less the current under consideration. Therefore,
for each, say the pth, current to be considered, the angle between the Ip and ID - Ip phasors is to be checked.
Ideally, during external faults, the said angle is close to 180° (as shown); and close to 0 degrees during internal faults.

CHAPTER 9: THEORY OF OPERATION SATURATION DETECTOR
Figure 9-4: Directional principle operation during external faults
External Fault Conditions
⎛ Ip ⎞
imag ⎜ ⎟
⎜ ID − I p ⎟ OPERATE
⎝ ⎠
BLOCK
⎛ Ip ⎞
ID - Ip real ⎜ ⎟
Ip ⎜ ID − I p ⎟
⎝ ⎠
BLOCK
OPERATE
836726A2.CDR
Figure 9-5: Directional principle operation during internal faults

Internal Fault Conditions
⎛ Ip ⎞
imag ⎜ ⎟
⎜ ID − I p ⎟ OPERATE
⎝ ⎠
BLOCK
⎛ Ip ⎞
ID - Ip real ⎜ ⎟
⎜ ID − I p ⎟
⎝ ⎠
Ip
BLOCK
OPERATE
836727A2.CDR
The B90 implementation calculates the maximum angle for the considered currents and compares it against a fixed
threshold of 90°. The flag indicating whether the directional protection principle is satisfied is available as the FlexLogic
operand BUS 1(4) DIR A/B/C.
9.5 Saturation detector

9.5.1 CT saturation detection 9
The saturation detector of the B90 takes advantage of the fact that any CT operates correctly for a short period of time,
even under very large primary currents that would subsequently cause a very deep saturation. As a result, in the case of
an external fault, the differential current stays very low during the initial period of linear operation of the CTs while the
restraining signal develops rapidly. Once one or more CTs saturate, the differential current increases. The restraining signal,
however, yields by at least a few milliseconds. During internal faults, both the differential and restraining currents develop
simultaneously. This creates characteristic patterns for the differential - restraining trajectory, as shown.

SATURATION DETECTOR CHAPTER 9: THEORY OF OPERATION
Figure 9-6: CT saturation detection internal and external fault patterns
N
differential
TTER
N
TER
LT PA
PAT
OPERATE
L FAU
T
AUL
BLOCK
AL F
RNA
ERN
INTE
E XT
TERN
EXTERNAL FAULT PAT
restraining
836728A1.CDR
The CT saturation condition is declared by the saturation detector when the magnitude of the restraining signal becomes
larger than the higher breakpoint (HIGH BPNT) and at the same time the differential current is below the first slope (LOW
SLOPE). The said condition is of a transient nature and requires a seal-in. A special logic in the form of a “state machine” is
used for this purpose as depicted in the following figure on saturation detector state machine.
As the phasor estimator introduces a delay into the measurement process, the aforementioned saturation test fails to
detect CT saturation occurring very fast. In order to cope with very fast CT saturation, another condition is checked that
uses relations between the signals at the waveform level. The basic principle is similar to that described. Additionally, the
sample-based stage of the saturation detector uses the time derivative of the restraining signal (di/dt) to better trace the
saturation pattern shown in the following figure.
The saturation detector is capable of detecting saturation occurring in approximately 3 ms from fault inception. The
saturation detector, although having no dedicated settings, uses the main differential characteristic for proper operation.
This must be kept in mind when setting the characteristic as its parameters must retain their original meaning.
The operation of the saturation detector is available as the FlexLogic operand BUS 1(4) SAT A/B/C.

CHAPTER 9: THEORY OF OPERATION OUTPUT LOGIC AND EXAMPLES
Figure 9-7: Saturation detector state machine
NORMAL
SAT := 0
The differential
current below the saturation
first slope for a condition
certain period of
time
EXTERNAL
FAULT
SAT := 1
The differential-
The differential restraining trajectory
characteristic out of the differential
entered characteristic for a
certain period of time
EXTERNAL
FAULT and CT
SATURATION
SAT := 1
836729A1.CDR
9.6 Output logic and examples

9.6.1 Output logic
The biased differential characteristic uses the output logic shown in the following figure.
For low differential signals, the biased differential element operates on the 2-out-of-2 basis utilizing both the differential
and directional principles.
For high differential signals, the directional principle is included only if demanded by the saturation detector (dynamic 1-
out-of-2 / 2-out-of-2 mode). Typically, the directional principle is slower, and by avoiding using it when possible, the B90
gains speed.
The dynamic inclusion/exclusion of the directional principle is not applied for the low differential currents but is included
permanently only because it is comparatively difficult to reliably detect CT saturation occurring when the currents are
small, for example saturation due to extremely long time constant of the DC component or due to multiple autoreclosure
actions.

OUTPUT LOGIC AND EXAMPLES CHAPTER 9: THEORY OF OPERATION
Figure 9-8: Output logic of biased differential protection
DIFL
AND
DIR biased bus

OR differential
OR DIFBIASED
SAT
AND
DIFH
836730A1.CDR
9.6.2 Internal and external fault example

Two examples of relay operation are presented: an external fault with heavy CT saturation and an internal fault.
The protected bus includes six circuits connected to CT terminals F1, F5, M1, M5, U1, and U5, respectively. The circuits F1,
F5, M1, M5, and U5 are capable of feeding some fault current; the U1 circuit supplies a load. The F1, F5, and U5 circuits are
significantly stronger than the F5 and M1 connections.
The M5 circuit contains the weakest (most prone to saturation) CT of the bus.
The first of the following figures presents the bus currents and the most important logic signals for the case of an external
fault. Despite very fast and severe CT saturation, the B90 remains stable.
The second figure presents the same signals but for the case of an internal fault. The B90 trips in 10 ms (fast form-C output
contact).

CHAPTER 9: THEORY OF OPERATION OUTPUT LOGIC AND EXAMPLES
Figure 9-9: External fault example

OUTPUT LOGIC AND EXAMPLES CHAPTER 9: THEORY OF OPERATION
Figure 9-10: Internal fault example

Chapter 10: Maintenance
Maintenance
This chapter outlines monitoring, maintenance, repair, storage, and disposal of the hardware and software.
10.1 Monitoring
Devices and data can be monitored.
10.1.1 Devices with Site Targets

To view an overview of devices:
1. Access the Site Targets item in the Online Window area, below the list of devices. It can take a few minutes for all
devices to be read.
2. Acknowledge any messages for unaccessible devices. The Site Targets window opens when done.
Figure 10-1: Site Targets window
10.1.2 Data with Modbus Analyzer

Use the Modbus Analyzer under Maintenance > Modbus Analyzer to monitor the values of the UR device. Use the Modbus
memory map addresses outlined in the UR Family Communications Guide for the entries.
The upper part of the window displays values. The lower part of the window is for factory service use.

MONITORING CHAPTER 10: MAINTENANCE
The first row in the figure shows that Contact Output 1 operation is being monitored. Its Modbus address is CAFA. The
actual value read from the device is 0, which means that it is off.
The second row in the figure shows the Contact Output 1 Name. It has a Modbus address of CAF0 and a default value of
"Cont Op 1." None of Selection column settings render this value because they present the information based on
numbering systems.
Figure 10-2: Modbus Analyzer used to monitor actual values on a UR
Address (HEX) — Modbus address in hexadecimal. See the Modbus memory map in the UR Family Communications Guide
or in the web interface (enter IP address of UR device in a web browser).
Modbus Type
Actual Value — To read the data in the UR device
Setting — To read a setting in the UR device
Coil — To read a command in the UR device
# of — Element, input, or output to read. An example is 1 for Contact Output 1.
Selection (examples demonstrate various ways to represent 0)
Hex — A decimal numbering system based on 16 possible values, from 0 to 9 and A to F. An example is 0x0000.
Char — A single unicode character, such as C. An example is 0.
Int — A 32-bit number, either positive or negative. An example is 0.
UInt — Unsigned 32-bit integer, which means that it cannot be negative but can be twice as large as a signed integer. An
example is 0.
Long — A 64-bit number, either positive or negative. An example is 0.
ULong — Unsigned 64-bit number, which means that it cannot be negative but can be twice as large as a signed 64-bit
number. An example is 0.
Float — A numbering system with no fixed number of digits before or after the decimal point. An example is 0.000000.
Binary — A numbering system using 0 and 1. An example is 0000-0000-0000-0000.
Entries are not saved when closing the window.
10

CHAPTER 10: MAINTENANCE GENERAL MAINTENANCE
10.2 General maintenance

The B90 requires minimal maintenance. As a microprocessor-based relay, its characteristics do not change over time.
Expected service life is 20 years for UR devices manufactured June 2014 or later when applied in a controlled indoor
environment and electrical conditions within specification.
While the B90 performs continual self-tests, it is recommended that maintenance be scheduled with other system
maintenance. This maintenance can involve in-service, out-of-service, or unscheduled maintenance.
10.2.1 In-service maintenance

1. Visual verification of the analog values integrity, such as voltage and current (in comparison to other devices on the
corresponding system).
2. Visual verification of active alarms, relay display messages, and LED indications.
3. LED test.
4. Visual inspection for any damage, corrosion, dust, or loose wires.
5. Event recorder file download with further events analysis.
10.2.2 Out-of-service maintenance

1. Check wiring connections for firmness.
2. Analog values (currents, voltages, RTDs, analog inputs) injection test and metering accuracy verification. Calibrated
test equipment is required.
3. Protection elements setting verification (analog values injection or visual verification of setting file entries against
relay settings schedule).
4. Contact inputs and outputs verification. This test can be conducted by direct change of state forcing or as part of the
system functional testing.
5. Visual inspection for any damage, corrosion, or dust.
6. Event recorder file download with further events analysis.
7. LED Test and pushbutton continuity check.
10.2.3 Unscheduled maintenance (system interruption)

View the event recorder and oscillography or fault report for correct operation of inputs, outputs, and elements.
10.3 Retrieve files

Data, oscillography, log, events, routing, ARP, and other files can be transferred using the EnerVista software to a computer
or to a USB flash drive when using the graphical front panel. These files can be requested by technical support staff.
To retrieve a file using EnerVista software:
1. If the CyberSentry option is enabled, log in to the EnerVista software using the Administrator role.
2. In the Online Window area of EnerVista, access Maintenance > Retrieve File. The window opens.
3. Note the destination folder to which the file is to be saved at the top and change it if required. You can copy the path
or open the folder for convenience at this time.
4. Select the file to download from the UR device. 10

RETRIEVE FILES CHAPTER 10: MAINTENANCE
5. Click the Read File button. The file is saved to the destination folder. The EnerVista window remains open to download
additional files.
To retrieve a file using a USB drive:

1. Insert the USB drive into the bottom USB port on the graphical front panel. The page displays on the front panel.
2. Using the Up or Down pushbuttons on the front panel, select the file.
3. Press the COPY pushbutton. The files are copied from the B90 to the USB drive.
Do not unplug the USB drive while copying is in progress, else the USB drive can be compromised.
4. When done, to exit unplug the USB drive or press the ESCAPE pushbutton.
10.3.1 CyberSentry security event files

CyberSentry security events are available in the following two files: SECURITY_EVENTS.CSV and SETTING_CHANGES.LOG.
10.3.1.1 Security events file

The figure shows the content for the SECURITY_EVENTS.CSV file.
Figure 10-3: Security events file
Time — Local time.

Activity — The actual security event.
1 = Authentication Failed
2 = User Lockout
3 = FW Upgrade
4 = FW Lock
5 = Settings Lock
6 = Settings Change, this can fill the entire event log. Hence it is supported by the already existing
SETTINGS_CHANGE.LOG file. This event is not required.
7 = Clear Oscillography command
8 = Clear Data Logger command
9 = Clear Demand Records command
10 = Clear Energy command
11 = Reset Unauthorized Access
12 = Clear Teleprotection Counters
13 = Clear All Records
14 = Role Log out
15 = Role Log in
10 Change Method — Format code F229 for the settings control change method.

CHAPTER 10: MAINTENANCE CONVERT DEVICE SETTINGS
0 = None
1 = Keypad
2 = Front port
3 = COM1 (not used)
4 = COM2 (RS485)
5 = Ethernet
10.3.1.2 Setting changes file

The SETTING_CHANGES.LOG file stores all the setting changes. A total of 1024 events are stored in a circular buffer in non-
volatile memory.
Figure 10-4: Setting changes file
10.4 Convert device settings

Settings files can be upgraded or downgraded to other firmware versions. For example, version 7.4 settings can be
upgraded to version 7.6.
Settings are reset to factory default upon conversion. For a graphical front panel, for example when upgrading from
version 7.6 to 7.7, single-line diagrams and cells configured for the Metering Editor are defaulted, while other graphical
front panel settings are retained.
When converting a settings file from version 7.20 or earlier to 7.70 or later, any IEC 61850 settings are defaulted, and
Edition 2 is used.
When converting a settings file from version since 7.30 inclusive to 7.70 or later, any IEC 61850 settings are converted and
Edition 2 is used.
To convert settings:
1. If not already in the Offline Window area, right-click the online device in the EnerVista software and select the Add
Device to Offline Window option. This copies the settings to the Offline Window area. Any message about file repair
usually means that settings were missing in the original file and have been added with default values to the new file.
2. Make a copy of the settings file in the Offline Window area by right-clicking the file and selecting Duplicate Device. A
copy of the file is made and the file name start with "Copy of." Optionally rename the file by right-clicking it and
selecting the Rename Device option.
3. Convert the settings by right-clicking one of the files in the Offline Window and selecting the Convert Device Settings
option.
If the option does not display, click the Admin > User Management menu item and enable the Update Info check box
for the user. Save.
Or if the option does not display, click the Admin > User Management menu item and enable the Enable Security
check box. Save. Select the Admin > User Login menu item. Enter "Administrator" for the user and enter the password.
(Contact GE Grid Solutions if you do not know the default password.)
10

CONVERT DEVICE SETTINGS CHAPTER 10: MAINTENANCE
GE recommends converting settings in firmware steps, for example when converting from 6.0 to 7.4x, convert first to
7.0 then 7.4 in order to follow embedded conversion rules and keep settings.
The settings convert and a report generates.
Figure 10-5: Upgrade settings
4. Review the conversion report. The values of all settings that have been defaulted during conversion are not listed in
the conversion report; to find the value of a setting before conversion, inspect the device backup file made before
conversion.
In the example shown here, settings have been reset to factory defaults and several settings are new in firmware
version 7.6 under Settings > System Setup > Switches and Breakers.
Figure 10-6: Conversion report
5. Change settings in the new file, for example by looking at the original file.
6. Write the converted file to the device, for example by dragging and dropping from the Offline Window to the Online
Window.
7. Check settings and operation.
10

CHAPTER 10: MAINTENANCE COPY SETTINGS TO OTHER DEVICE
10.5 Copy settings to other device

Settings from one B90 device can be copied to another B90 device for rapid deployment. The order codes and IEC 61850
edition must match. See the Settings File section at the beginning of the Interfaces chapter for a list of settings not
deployed.
To apply settings to another device:
1. Right-click the device in the Online window and select the Add Device to Offline Window option. A window opens.
2. Check the file path and name the file, then click the Receive button. An example is to save the files in
D:\Users\Public\Public Documents\GE Power Management\URPC\Data\ and to name the source device
B90_Deployment. At the prompt, confirm the action. The settings are saved in .cid, .icd, and .urs files, and the entry
displays in the Offline window area.
3. Right-click the device in the Offline window area and select the Duplicate Device option. The device is copied with a
prefix of "Copy of." Multiple duplicates results in files being named "Copy of Copy of" for example, which can be
avoided by deleting the folder copies from the path shown on mouse-over.
4. Right-click the copied device and rename it.
5. Right-click the copied device and select the Edit Device Properties option. Make the changes for the new device.
6. Send the file to new device by dragging and dropping it into the Online Window area. Or right-click and select the
Write Settings to Device option.
7. Update the remaining settings, such as IP address.
10.6 Compare settings

Settings are comparable against default values and between two UR devices.
Some of the IEC 61850 settings use floating point data, which guarantees accurate representation of real numbers up to
seven digits. Numbers with more than seven digits are approximated within a certain precision. This can result in
differences between what is entered and what is saved, and for example results in differences shown on a settings
comparison report.
When comparing two settings files with the graphical front panel, all graphical front panel features are compared except
for the single-line diagrams.
10.6.1 Compare against defaults

To compare settings against default values:
1. Right-click the device in the Offline Window area and select Compare Settings With Defaults. The file generates and
the number of differences displays.
2. To save the report, click File > Save As, select the TXT, PDF, or CSV format from the drop-down list, and enter a name
for the file.
In the figure, the first entry (red) is from the device, while the second (green) is the default value.
Figure 10-7: Device settings compared with default values
10

BACK UP AND RESTORE SETTINGS CHAPTER 10: MAINTENANCE
10.6.2 Compare two devices

Preferences are set under File > Preferences as follows:
• Comparison Report: Sequential File 1, File 2 Layout — When disabled (default), the report shows only what differs, as
shown in the previous figure. When enabled, the report indicates differences by device.
Figure 10-8: Device settings compared between two devices, displayed sequentially
There are two ways to compare devices: devices in the Offline area or between Online and Offline devices.
To compare settings of two devices in the Offline Window area:
1. Right-click a first device in the Offline Window area and select Compare Two Devices.
2. In the window that opens, select a second device and click the Receive button. The file generates and the number of
differences displays.
3. To save the report, click File > Save As, select the TXT, PDF, or CSV format from the drop-down list, and enter a name
for the file.
To compare settings between Online and Offline devices:

1. Right-click a device in the Online Window area and select Compare with Device.
2. In the window that opens, enter a path/file name at the bottom o f the window.
3. Select the second device.
4. Click the OK button. The file generates, and the differences are highlighted in red, which is for the first device.
10.7 Back up and restore settings

Back up a copy of the in-service settings for each commissioned UR device, so as to revert to the commissioned settings
after inadvertent, unauthorized, or temporary setting changes are made, after the settings defaulted due to firmware
upgrade, or when the device has to be replaced. This section describes how to backup settings to a file and how to use
that file to restore the settings to the original relay or to a replacement relay.
For reference, settings can saved with Online > Print Device Information and Online > Export Device Information. They
cannot be restored using these options.
10.7.1 Back up settings

The following file types can be saved:
• URS — UR settings file — When the IEC 61850 option is not present
• ICD — IED Capability Description file — Default settings on UR
• CID — Configured IED description file — Settings sent to the UR (may or may not contain the present settings)
10 UR device settings can be saved in a backup URS file using the EnerVista UR Setup software. The URS file is the standard
UR settings file. For an introduction to settings files in the URS format, see the beginning of the Interfaces chapter.

CHAPTER 10: MAINTENANCE BACK UP AND RESTORE SETTINGS
When the IEC 61850 option is present, the settings can be saved alternatively in a backup IID file either using the EnerVista
UR Setup software in online mode or by using any of the supported file transfer protocols. The IID file is one of several IEC
61850 Substation Configuration Language (SCL) file types; see the IEC 61850 chapter in the UR Series Communications
Guide for an introduction to SCL.
"TBD" displays when a setting in a modeled element is configured with a non-modeled operand. For example, Phase IOC is
modeled in a firmware release, while the LED operands are not modeled. If the block setting of the Phase IOC is configured
with LED operands, its displays as TBD in IID and CID files, the web interface, or in an MMS client.
The options that display in the EnerVista software when right-clicking depend on device options.
Preferences are set in the File > Preferences > IEC 61850 menu. There are two options as follows:
• Preserve custom attributes when importing SCD/CID files — Applies to the Add Device to Offline Window option.
When enabled, the IID file also is to be copied to the computer. The IID file that is retrieved from the relay is therefore
assumed to be in synchronization with the resulting .urs file, and in fact in this situation the IID file on the computer is
a copy of the IID file that was read from the online device. When disabled, the IID file on the computer is to be left
unchanged. The location of the IID file is C:\ProgramData\GE Power Management\urpc\Offline, for example.
• Do not update IID file when updating SCL files — When enabled (default), an IID file is not to be created on the
computer and if one is already present there, it is neither removed nor updated. Have this option enabled when you
want to keep the IID file from the UR device instead of from another tool. The location of the file is C:\ProgramData\GE
Power Management\urpc\Offline, for example.
An Environment backup stores a list of sites and devices in the Online and Offline Window areas. Settings files are not
contained within the environment file. If a settings file is moved, renamed, or deleted after the backup, it is removed from
the Offline Window during the restore.
To save a settings file in the URS format in EnerVista Online Window:

1. In EnerVista, connect to the device in the Online Window area.
2. Right-click the device name in the Online Window area and select Add Device to Offline Window. A window opens.
3. Select or enter a file name and location, and click the Receive button. A .urs file is created in the Offline Window area.
To create a new settings file in the URS format in EnerVista Offline Window:
1. In EnerVista, right-click in the Offline Window area and select New Device. A window opens.
2. Change the file name at the end of the Path field, keeping the .urs extension.
3. From the Associate File with Device drop-down list, select the UR device. Other fields complete automatically.
Otherwise, when you do not select a device from the drop-down list, all fields need to be completed manually and
only devices that match the entered order code and version display in the list.
4. The Serial # Lock field is the serial number of the intended device. It ensures that the settings file is sent only to the
specific relay that matches the serial number.
5. Click the OK button to create the .urs file in the Offline Window area.
To save settings in the IID format in EnerVista Online Window:

2. Right-click the device name in the Online Window area and select Read IID File. The option is not present when the
device does not have the IEC 61850 option. A window opens when successful.
3. Select or enter a file name and location, and click the Receive button. A .iid file is created.
To save settings in the IID format in EnerVista Offline Window:

1. In EnerVista, right-click the device in the Offline Window area.
2. Select the Create IID File option for firmware below 7.3. The option is not always available. Select the Save As option
for firmware 7.3 and later, and select the IID option from drop-down list. 10

No file is generated. The IID file on the computer is copied to the location specified.
3. If the Do not update IID file when updating SCL files preference is enabled under File > Preferences > IEC 61850,
then a message displays to that effect. This means that there is no IID file available on the computer to be copied, so
a new one is generated.
To save settings in the IID format using TFTP:

1. On a computer on the same subnetwork as the UR device, open a command window.
2. Enter
TFTP <IP address> GET ur.iid <destination>
where
<IP address> is the IP address of the UR device
ur.iid is the internal name of the IID file in the UR device
<destination> is the path and file name of the IID file. If omitted, the file is saved as ur.iid in the command window
default directory.
An example is
TFTP 192.168.1.101 GET ur.iid Feeder1.iid
To save settings in the ICD format in EnerVista Online Window:

1. In EnerVista, right-click the device in the Online Window area.
2. Select the Read ICD File option. A window opens.
3. Enter a path/name for the file, and click the Save button.
To save settings in the ICD format in EnerVista Offline Window:

2. Select the Create ICD File option. Or select the Save As option, and select the ICD option from drop-down list.
You can be prompted to specify if the file is for firmware version 7.12 or later.
The file is saved to the location specified.
To save settings in the CID format in EnerVista Online Window:

1. In EnerVista, right-click the device in the Online Window area.
2. Select the Read ICD File option. A window opens.
3. Enter a path/name for the file, and click the Save button.
To save settings in the CID format in EnerVista Offline Window:

2. Select the Save As option, which displays for firmware 7.3 and later, and select the CID option from the drop-down list.
The file is copied from the computer to the location specified.
To save list of sites and devices with an Environment backup:

1. In EnerVista, click File > Environment > Backup. A window opens.
2. Name and save the .ENV file.
10

CHAPTER 10: MAINTENANCE BACK UP AND RESTORE SETTINGS
10.7.2 Restore settings

UR device settings can be restored to the values they were at when a URS backup file was created using the EnerVista UR
Setup software. When the IEC 61850 option is present, the settings can alternatively be to the values they were at when an
IID type backup was created either using the EnerVista UR Setup software in online mode or by using any of the supported
file transfer protocols. Note that TFTP cannot be used here, as TFTP "put" mode is disabled for security reasons.
To restore completely, a few settings need to be entered manually either via EnerVista UR Setup or via the UR device front
panel. If the restore operation is to be via Ethernet, first the UR device must have its IP address settings entered via the
front panel. These are located at SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK 1(3) and SETTINGS 
PRODUCT SETUP  COMMUNICATIONS  IPv4 ROUTE TABLE 1(6)  DEFAULT IPv4 ROUTE  GATEWAY ADDRESS.
When importing a file, it cannot have a blank numeric value. All numeric values must be non-blank, otherwise the file is
rejected.
URS and IID procedures are outlined here.
To restore settings from a URS file:
2. Right-click the .urs file in the Offline Window area and select Add Device from File to locate a file, and/or drag-and-
drop the file from the Offline Window area to the device in the Online Window area.
Figure 10-9: Restoring a URS settings file
3. Two prompts are possible, first that the URS file does not include the complete IEC 61850 configuration and that it
needs to be recreated if you continue. This means that the URS file is from UR version 7.30 or higher, has the IEC 61850
software option in the order code, but any IEC 61850 content will be compromised and will need to be configured.
Second, a message can display that the URS file is part of a device folder and to use the device’s CID file. This means
that the URS file is from UR version 7.3 or higher, has the IEC 61850 software option in the order code, and is part of the
device folder. The user is trying to add a URS file from inside a device’s folder. Instead, the user needs to use the CID file
from the device folder.
These messages display because the roles of the protection engineer and network engineer can be separate. The
former can require a URS file, while the latter can require stored Modbus settings and protection schemes. 10

4. Manually copy the remaining settings, outlined as follows.
To restore settings from an IID file using EnerVista software:

1. In Windows, make a copy the IID file with a cid extension.
2. Connect to the device in the Online Window area.
3. In the Offline Window area, right-click Devices and select Import Devices from SCD.
Figure 10-10: Importing an SCD or CID file
4. Navigate to and select the file with .cid extension. When prompted, enter a file name to give to an intermediate URS
file. The URS file is added to the Offline Window area.
5. Drag the imported file in the Offline Window to the device in the Online Window. Note that the RELAY SETTINGS value
also is written to a device, and the accepting relay is put into "Programmed" or "Not Programmed" mode as
configured in the offline file.
To restore settings from an IID using SFTP:

1. In Windows, make a copy the IID file with a cid extension.
2. On a computer on the same subnetwork as the UR device, open a SFTP client application, such as WinSCP. Note that
TFTP cannot be used here.
3. Use the device's IP address as the host name.
4. If the device has the CyberSentry option, use the User Name of "Administrator" or "Engineer", and the password
programmed for the selected role. The default password is "ChangeMe1#" (without quotation marks).
5. If the device does not have the CyberSentry option, use the User Name of "Setting", and the password programmed for
the Setting role. The default password is "ChangeMe1#" (without quotation marks).
6. Upload the backup file copy with the CID extension. WinSCP uses drag-and-drop or copy-and-paste for this.
To manually copy remaining settings:

1. Settings listed in section 4.1.2 Settings Files are not transferred to the UR device with settings files. Enter them
manually either via the front panel or via EnerVista UR Setup software. The values that these settings had at the time
the backup was created are contained within the backup file, accessed through EnerVista UR Setup software.
To restore the list of sites and devices from an Environment backup:

1. In EnerVista, click File > Environment > Restore. A window opens.
2. Select the .ENV file to restore.
10

CHAPTER 10: MAINTENANCE UPGRADE SOFTWARE
10.8 Upgrade software

In general, the latest releases of the EnerVista software can be used with all firmware versions. For example, EnerVista
software released for UR 7.4 can be used to access multiple UR devices that have version 7.4x, 7.2x, and 6.0x firmware
installed.
Existing installations do not need to be uninstalled before upgrade.
You can also downgrade the software; use the same procedure.
To upgrade the EnerVista software:
1. If a beta version of the EnerVista UR Setup software is installed, uninstall it, for example using the Windows Control
Panel.
2. For Windows 10, disconnect any USB cable to the B90, else the UR USB drivers do no install correctly.
3. Download the latest EnerVista software and/or firmware from
http://www.gegridsolutions.com/app/ViewFiles.aspx?prod=urfamily&type=7
4. Double-click the file and complete the wizard. The software installs.
5. Access the software and check the version number under Help > About. If the new version does not display, try
uninstalling the software and reinstalling the new versions.
6. For Windows 10, to finish installing the UR USB driver, open Device Manager > Ports, then plug in the USB cable (to
connect the relay and computer). A new port starting with "GE Virtual Serial Port" is available. If available, click the OK
button to complete the installation.
If not available, uninstall the existing GE USB driver in the Device Manager > Ports. (Right-click and "Uninstall.")
When complete, unplug and re-plug the USB cable connecting the UR device. The "GE Virtual Serial Port" driver is now
available.
A message can display about a version not being supported. An example is when upgrading from version 7.12K to 7.4x.
The 7.12K entry is removed from the Offline Window area.
A message can display in the EnerVista software upon launch that "a device from the environment was not recognized."
This means that a device is online and its firmware version conflicts with the software version. In the example shown, a
C60 with firmware version 7.5x is online, but the software version is 7.3x. Updating removed incompatible files and
changed the device to version 7.3x, after which you need to make the order codes consistent as outlined next.
Figure 10-11: Mismatch in order code between software and device
To make the order codes consistent:

1. In EnerVista, click the Device Setup button. The window opens.
2. Expand the entry for the UR device.
3.
4.
Click the Read Order Code button. The order code and version of the device are populated to the software.
Click the OK button to save the change.
10

UPGRADE FIRMWARE CHAPTER 10: MAINTENANCE
10.9 Upgrade firmware

If upgrading both EnerVista software and B90 firmware, upgrade the software first.
The firmware of the B90 device can be upgraded, locally or remotely, using the EnerVista software.
Upgrades are possible for the same release (such as 7.01 to 7.02) and from one firmware version to another (such as 7.2 to
7.3). When upgrading to another firmware version, check the release notes on the GE Multilin website for compatibility.
If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first.
Address equipment mismatch error before upgrade. For example, if you have a basic front panel attached and the order
code in the device is for a graphical front panel, the upgrade only works with a graphical front panel.
You can also downgrade firmware; use the same procedure.
To upgrade the firmware using EnerVista software:
1. If required, download the boot file and/or firmware from
http://www.gegridsolutions.com/app/ViewFiles.aspx?prod=urfamily&type=7
The firmware and boot files are .bin files.
2. Navigate to Settings > Product Setup > Security and ensure that the Remote Setting Authorized and Local Setting
Authorized settings are "ON." On the front panel of the device, the path is SETTINGS  PRODUCT SETUP  SECURITY 
DUAL PERMISSION SECURITY ACCESS.
If using CyberSentry security, also ensure that the relay and firmware are not locked under the Settings > Product
Setup > Security > Supervisory settings. A Supervisor role is required for these settings.
3. In EnerVista, back up the device settings by right-clicking the device and selecting Add Device to Offline Window. In
the window that displays, select an existing file to overwrite, or enter a name for a new settings file and optionally a
location for the new file. Click the Receive button to start the backup.
If an "Incompatible device order codes or versions" message displays, it means that you are trying to overwrite a file
for another product. You access the Convert Device Settings option by right-clicking the file in the Offline Window
area at the lower left. GE recommends converting settings in firmware steps, for example when converting from 6.0 to
7.4x, convert first to 7.0 then 7.4 in order to follow embedded conversion rules and keep settings. Note that the values
of all settings that have been defaulted during conversion are not listed in the conversion report; to find the value of a
setting before conversion, inspect the device backups made before conversion.
4. In EnerVista, navigate to Maintenance > Update Firmware.
First select the boot file if applicable, locating the .bin file, and proceed. Restart the device, the EnerVista software, and
refresh the order code in EnerVista under the Device Setup button.
To update the firmware, click Maintenance > Update Firmware, select the firmware update by locating the .bin file,
and proceed with the update.
When asked if upgrading over the Internet, the difference is the flash memory buffer size each time the software
sends data to the relay. Yes means that the flash memory buffer size is 256 bytes. No means that it is 1024 bytes,
which is faster.
If a warning message displays about the firmware not being supported by the EnerVista software, it means that the
firmware is a later version than the software. Upgrade the software to the same or later version as the firmware, then
try again.
If an "Unable to put relay in flash mode" message displays, set the Settings > Product Setup > Security > Dual
Permission Security Access > Remote Setting Authorized and Local Setting Authorized settings to "ON" and try
again.
When the update is finished, the relay restarts automatically. The upgrade process takes about 20 minutes when
using a graphical front panel because of writing to the front panel.
5. Restart the EnerVista software, and refresh the order code in EnerVista under the Device Setup button.
6. Verify the boot and firmware version while the device is starting up or in EnerVista under Actual Values > Product Info
> Firmware Revisions. The boot revision is not the same as the firmware revision, and the firmware revision reflects
10 7.
the UR release, for example firmware revision 7.40 is UR release 7.40.
Set the device to "programmed" under Settings > Product Setup > Installation. A self-test error displays on the device

CHAPTER 10: MAINTENANCE REPLACE FRONT PANEL
until this is done.

8. If you changed the Remote Setting Authorized, the Local Setting Authorized settings, or relay lock settings, return
them to their previous settings.
9. To apply any previously saved settings, right-click the saved settings file in the Offline Window area and select Write
to Device. Optionally convert the saved settings to the new firmware version before writing to the device by right-
clicking and selecting Convert Device Settings.
The field-programmable gate array (FPGA) can be upgraded under Maintenance > Update FPGA when the device
is connected via serial cable and the firmware revision is 7.0 or higher.
Modbus addresses assigned to firmware modules, features, settings, and corresponding data items (that is, default
values, minimum/maximum values, data type, and item size) can change slightly from version to version of
firmware. The addresses are rearranged when new features are added or existing features are enhanced or
modified. The EEPROM DATA ERROR message displayed after upgrading/downgrading the firmware is a resettable,
self-test message intended to inform users that the Modbus addresses have changed with the upgraded firmware.
This message does not signal any problems when appearing after firmware upgrades.
10.10 Replace front panel

This section outlines how to install a graphical front panel.
A graphical front panel with a seven-inch (17.8 cm) color display and USB port is available for horizontal units. When
purchased separately as a retrofit for an existing relay, there is one kit for an enhanced front panel replacement and
another kit for the basic front panel replacement, with mounting brackets differing between the two kits. A kit includes the
graphical front panel, mounting brackets, and screws. The graphical front panel requires CPU module type W or module
type T, U, or V (newer type that has two connector slots on the front of the module--the second is difficult to see), upgrades
of software and firmware, then a settings update to recognize the graphical front panel.
The graphical front panel can replace a basic front panel on newer models where the hinges are not riveted to the chassis.
It cannot replace a basic front panel where the hinges are riveted onto the chassis; both front panel and chassis require
replacement. See the photo of the riveted hinges later in this section.
• Remove front panel
• Install graphical front panel
• Replace CPU module
• Upgrade software and firmware, then update setting
Withdraw or insert a module only when control power has been removed from the unit, and be
sure to insert only the correct module type into a slot, else personal injury, damage to the unit or
connected equipment, or undesired operation can result.
To avoid damage to the equipment, use proper electrostatic discharge protection (for example, a
static strap) when coming in contact with modules while the relay is energized.
The following procedure can be used for the Rev. 1 and Rev. 2 enhanced front panels, with Rev. 1 is documented here. The
Rev. 2 enhanced horizontal front panel introduced starting November 2017 uses a screw to close it and internal hinge
screws as per the graphical front panel.
To remove an enhanced or basic front panel:
1. In the EnerVista software or on the front panel, access Settings > Product Setup > Communications > Network and
record the IP address and subnet mask of the port(s) being used. Record the gateway address under Default IPv4
Route.
2.
3.
Turn off power to the unit. Hot-swapping of the front panel is not supported.
For an enhanced front panel, loosen the thumb screw and open slightly the front panel.
10

REPLACE FRONT PANEL CHAPTER 10: MAINTENANCE
For a basic front panel, lift up the black plastic latch on the right side of the front panel and open slightly the front
panel.
Figure 10-12: Loosen thumb screw on enhanced front panel to open
Figure 10-13: Lift latch on basic front panel to open
4. With a Phillips screwdriver, unscrew and remove the mounting bracket on the right side of the unit. The bracket for the
enhanced front panel looks similar to that for the graphical front panel, but they are not the same.
10

Figure 10-14: Remove enhanced front panel mounting bracket on right side
Figure 10-15: Remove basic front panel mounting bracket on right side
5. Open the front panel. Unplug or unscrew the grey ground cable from the front panel. Unplug the RJ45 connector from
the CPU module in the second slot on the left.
10

Figure 10-16: Disconnected ground cable and CPU connector
6. Unscrew and remove the mounting bracket with the front panel from the left side.
Figure 10-17: Unscrew enhanced front panel mounting bracket on left side
Figure 10-18: Unscrew basic front panel mounting bracket on left side
10

(note riveted hinges with red arrows - cannot replace this front panel)
The front panel has been removed.
To install the graphical front panel:

1. With power to the unit off, screw the left mounting bracket to the outside of the relay. The power supply module can
remain in the first slot.
Figure 10-19: Attach mounting bracket to relay on left side (no power supply module in first slot)
2. Screw the right mounting bracket to the right side of the relay. 10

Figure 10-20: Attach mounting bracket to relay on right side
3. Attach the graphical front panel hinge to the left mounting bracket using the nuts provided.
Figure 10-21: Attach to left mounting bracket inside relay
4. Close the front panel without tightening the screw to the mounting bracket.
5. Optionally remove the protective plastic film on the graphical front panel. It is normally peeled off, but also can be left
on.
The graphical front panel has been installed but not connected.
10

To replace the CPU module:

1. With power to the unit off, at the back of the CPU module in the second slot, disconnect any cables. Remove the silver
SFP connector(s) from the CPU module, and keep it handy. Then remove the CPU module by sliding the module out
from the front of the relay. (See the next section for instructions.)
Figure 10-22: Remove silver SFP connector (shown here under LK1 label)
2. At the front of the relay, insert the new CPU module in the second slot. The new CPU has two connection slots on the
front. Ensure that the RS485 connector and the black cover plate are not on the back of the CPU module before sliding
the module into the front of the relay.
Figure 10-23: Rear of a CPU module before insertion without RS485 connector or cover plate
10

3. Once the module is in place, connect the graphical front panel to the CPU module (ground and upper connector) and
close the front panel. There are two connections possible on the front of the CPU module: upper for the graphical front
panel and lower for the enhanced and basic front panels. The upper connection is black with holes, similar to the
cover, so it is difficult to see.
Figure 10-24: Connect graphical front panel to top connection on CPU module
4. Tighten the embedded screw on the right side of the graphical front panel to the mounting bracket.
Figure 10-25: Screw to attach graphical front panel to mounting bracket
5. At the back of the CPU module, attach the new black cover plate to the back of the relay, then connect the new RS485
connector.
10 6.
Insert the silver SFP connector(s) at the back of the CPU module, then connect any Ethernet connection(s).
Power up the relay. If the graphical front panel does not power up immediately, disconnect power, open the front

CHAPTER 10: MAINTENANCE REPLACE MODULE
panel, then check that the graphical front panel is plugged into the upper connection, not the lower silver connection
on the CPU module.
To upgrade software and firmware.

1. Upgrade the EnerVista software as outlined in this chapter.
2. Input the IP address and subnet mask of the relay on the front panel under Settings > Product Setup >
Communications > Network, and input the gateway address under Default IPv4 Route.
3. Upgrade the firmware in the EnerVista software as outlined in this chapter, for example under Maintenance > Update
Firmware.
If you see error messages after the upgrade, disconnect power to the relay and shut down the software, then start
both again. If you see a flashing message about front panel communications trouble, check the connection of the
graphical front panel to the CPU module.
4. In the EnerVista software, click the Device Setup button and refresh the order code for the device.
5. Set the relay to Programmed mode under Settings > Product Setup > Installation.
6. Update the EnerVista software to recognize the graphical front panel under Maintenance > Change Front Panel. This
setting does not display for units already with a graphical front panel.
If an equipment mismatch error displays on the front panel, it can mean that the order code on the device needs to be
updated to the new front panel.
10.11 Replace module

This section outlines how to replace a module.
Withdraw or insert a module only when control power has been removed from the unit, and be
sure to insert only the correct module type into a slot, else personal injury, damage to the unit or
connected equipment, or undesired operation can result.
To avoid damage to the equipment, use proper electrostatic discharge protection (for example, a
static strap) when coming in contact with modules while the relay is energized.
The relay, being modular in design, allows for the withdrawal and insertion of modules. Replace modules only with like
modules in their original factory configured slots.
Two procedures follow: replace a module with the same module, and upgrade a module.
To replace a module with the same module:
1. Open the enhanced front panel to the left once the thumb screw has been removed. This allows for easy access of the
modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and
allows easy access to all modules in the B90.
10

REPLACE MODULE CHAPTER 10: MAINTENANCE
Figure 10-26: Modules inside relay with front cover open (enhanced front panel)
The basic front panel can be opened to the left once the black plastic sliding latch on the right side has been pushed
up, as shown below.
Figure 10-27: Removing module (basic front panel)
2. With power to the unit off, disconnect individually the connections at the front and back of the module before
removing the module from the chassis.
For any Process Card/process bus module in slot H for use with a HardFiber Brick, also remove the two screws at the
back that attach the module to the chassis.
3. To properly remove a module, pull simultaneously the ejector/inserter clips, located at the top and bottom of the
module. Record the original location of the module to ensure that the same or replacement module is inserted into the
correct slot. While modules with current input provide automatic shorting of external CT circuits, for CT/VT modules it
is recommended to short/isolate external circuits accordingly for maximum safety.
4. To properly insert a module, ensure that the correct module type is inserted into the correct slot position. The ejector/
inserter clips located at the top and at the bottom of each module must be in the disengaged position as the module
is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips
simultaneously. When the clips have locked into position, the module is fully inserted.
When adding a module (versus replacing a module), check that settings have not changed. Depending on the
module, settings can reset to default values.
10

CHAPTER 10: MAINTENANCE BATTERY
The new CT/VT modules can only be used with new CPUs; similarly, old CT/VT modules can only be used with old
CPUs. In the event that there is a mismatch between the CPU and CT/VT module, the relay does not function and a
DSP ERROR or HARDWARE MISMATCH error displays.
An upgrade example is replacing the CPU module with a more recent one, such as swapping 9G/9H/9N with 9T/9U/9V/9W.
A power supply module upgrade does not affect an order code.
To upgrade a module:
1. Back up settings by sending the device to the Offline Window area. Convert the settings to the new order code by
right-clicking in the Offline Window area. Replace the module as outlined in the previous procedure. In the Online
Window area, reset all settings to factory defaults and read the new order code from the device using Commands >
Relay Maintenance > Update Order Code. Send the saved settings from the Offline Window area to the online device.
Refresh the order code in the Device Setup window and set the device to "Programmed" under Settings > Product
Setup > Installation.
10.12 Battery
A battery powers the real time clock on startup of the device.
When required, the battery can be replaced. The battery type is 3 V cylindrical.
The power supply module contains the battery. The power supply modules were upgraded in 2014 to SH/SL from RH/RL,
but the order code when purchasing a UR with redundant power supply remained as RH/RL so that customers can
continue to use the same order codes. The order code can read RH or RL, while the module inside the unit reads SH or SL.
The order code for replacement redundant power supply modules was changed to SH/SL.
10.12.1 Replace battery

When required, the battery can be replaced. The power supply module contains the battery.
To avoid injury, ensure that the unit has been powered off for a minimum of three minutes before
replacing the battery.
Risk of fire if battery is replaced with incorrect type or polarity.
To replace the battery:
1. Turn off the power to the unit.
2. Wait a minimum of three minutes to ensure that there is no power to the battery.
3. As outlined in the previous section, open the unit by sliding up the plastic latch on the right side of the front panel
(basic front panel) or unscrewing the panel (enhanced front panel).
4. For the basic front panel, it needs to be removed in order to access the power supply module, which is typically in the
first slot on the left side and blocked by the hinge of the front panel. To remove the front panel, unscrew the bracket on
the left side of the unit.
5. Remove the power supply module by simultaneously pulling the ejector clips at the top and bottom of the module and
sliding it out.
6. Unscrew all four screws (not three) that attach the metal cover to the module. The fourth screw is at the back end of
the module, on the opposite side from the clips, beside the white electronics part (see figure).
7. Slide the metal cover away from the clips about 0.5 cm (1/8 inch) and remove the cover.
8. Unclip the black plastic holder that keeps the battery in place. The plastic clips into the socket at the bottom on both
sides—pull the plastic away from the battery. Use a flat-head screwdriver if you cannot unclip the plastic with your
fingers.
9. Replace the battery with the identical make and model. For example, do not use a rechargeable battery. Observe the
+ and - polarity of the battery and replace it with the same polarity as marked on the battery holder. 10

BATTERY CHAPTER 10: MAINTENANCE
Figure 10-28: Battery location on power supply module
10. Reinstall the battery holder and the metal cover, and reinsert the power supply module into the unit.
11. Power on the unit.
12. Dispose of the old battery as outlined in the next section.
10.12.2 Dispose of battery
10.12.2.1 EN Battery disposal

This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.
10.12.2.2 CS Nakládání s bateriemi

Tento produkt obsahuje baterie, které nemohou být zneškodněny v Evropské unii jako netříděný komunální odpadu. Viz
dokumentace k produktu pro informace pro konkrétní baterie. Baterie je označena tímto symbolem, který může zahrnovat
i uvedena písmena, kadmium (Cd), olovo (Pb), nebo rtuť (Hg). Pro správnou recyklaci baterií vraťte svémudodavateli nebo
na určeném sběrném místě. Pro více informací viz: www.recyclethis.info.
10.12.2.3 DA Batteri affald

Dette produkt indeholder et batteri som ikke kan bortskaffes sammen med almindeligt husholdningsaffald i Europa. Se
produktinformation for specifikke informationer om batteriet. Batteriet er forsynet med indgraveret symboler for hvad
batteriet indeholder: kadmium (Cd), bly (Pb) og kviksølv (Hg). Europæiske brugere af elektrisk udstyr skal aflevere kasserede
produkter til genbrug eller til leverandøren. Yderligere oplysninger findes på webstedet www.recyclethis.info.
10

CHAPTER 10: MAINTENANCE BATTERY
10.12.2.4 DE Entsorgung von Batterien

Dieses Produkt beinhaltet eine Batterie, die nicht als unsortierter städtischer Abfall in der europäischen Union entsorgt
werden darf. Beachten Sie die spezifischen Batterie-informationen in der Produktdokumentation. Die Batterie ist mit
diesem Symbol gekennzeichnet, welches auch Hinweise auf möglicherweise enthaltene Stoffe wie Kadmium (Cd), Blei (Pb)
oder Quecksilber (Hektogramm) darstellt. Für die korrekte Wiederverwertung bringen Sie diese Batterie zu Ihrem lokalen
Lieferanten zurück oder entsorgen Sie das Produkt an den gekennzeichneten Sammelstellen. Weitere Informationen
hierzu finden Sie auf der folgenden Website: www.recyclethis.info.
10.12.2.5 EL Απόρριψη μπαταριών

Αυτό το προϊόν περιέχει μια μπαταρία που δεν πρέπει να απορρίπτεται σε δημόσια συστήματα απόρριψης στην
Ευρωπαϊκή Κοινότητα. ∆είτε την τεκμηρίωση του προϊόντος για συγκεκριμένες πληροφορίες που αφορούν τη μπαταρία.
Η μπαταρία είναι φέρει σήμανση με αυτό το σύμβολο, το οποίο μπορεί να περιλαμβάνει γράμματα για να δηλώσουν το
κάδμιο (Cd), τον μόλυβδο (Pb), ή τον υδράργυρο (Hg). Για την κατάλληλη ανακύκλωση επιστρέψτε την μπαταρία στον
προμηθευτή σας ή σε καθορισμένο σημείο συλλογής. Για περισσότερες πληροφορίες δείτε: www.recyclethis.info.
10.12.2.6 ES Eliminacion de baterias

Este producto contiene una batería que no se pueda eliminar como basura normal sin clasificar en la Unión Europea.
Examine la documentación del producto para la información específica de la batería. La batería se marca con este
símbolo, que puede incluir siglas para indicar el cadmio (Cd), el plomo (Pb), o el mercurio (Hg ). Para el reciclaje apropiado,
devuelva este producto a su distribuidor ó deshágase de él en los puntos de reciclaje designados. Para mas información :
wwwrecyclethis.info.
10.12.2.7 ET Patareide kõrvaldamine

Käesolev toode sisaldab patareisid, mida Euroopa Liidus ei tohi kõrvaldada sorteerimata olmejäätmetena. Andmeid
patareide kohta vaadake toote dokumentatsioonist. Patareid on märgistatud käesoleva sümboliga, millel võib olla
kaadmiumi (Cd), pliid (Pb) või elavhõbedat (Hg) tähistavad tähed. Nõuetekohaseks ringlusse võtmiseks tagastage patarei
tarnijale või kindlaksmääratud vastuvõtupunkti. Lisainformatsiooni saab Internetist aadressil: www.recyclethis.info.
10.12.2.8 FI Paristoje ja akkujen hävittäminen

Tuote sisältää pariston, jota ei saa hävittää Euroopan Unionin alueella talousjätteen mukana. Tarkista tuoteselosteesta
tuotteen tiedot. Paristo on merkitty tällä symbolilla ja saattaa sisältää cadmiumia (Cd), lyijyä (Pb) tai elohopeaa (Hg). Oikean
kierrätystavan varmistamiseksi palauta tuote paikalliselle jälleenmyyjälle tai palauta se paristojen keräyspisteeseen.
Lisätietoja sivuilla www.recyclethis.info.
10.12.2.9 FR Élimination des piles

Ce produit contient une batterie qui ne peuvent être éliminés comme déchets municipaux non triés dans l'Union
européenne. Voir la documentation du produit au niveau des renseignements sur la pile. La batterie est marqué de ce
symbole, qui comprennent les indications cadmium (Cd), plomb (Pb), ou mercure (Hg). Pour le recyclage, retourner la
batterie à votre fournisseur ou à un point de collecte. Pour plus d'informations, voir: www.recyclethis.info.
10.12.2.10 HU Akkumulátor hulladék kezelése

Ezen termék akkumulátort tartalmaz, amely az Európai Unión belül csak a kijelölt módon és helyen dobható ki. A terméken
illetve a mellékelt ismertetőn olvasható a kadmium (Cd), ólom (Pb) vagy higany (Hg) tartalomra utaló betűjelzés. A hulladék
akkumulátor leadható a termék forgalmazójánál új akkumulátor vásárlásakor, vagy a kijelölt elektronikai
hulladékudvarokban. További információ a www.recyclethis.info oldalon.
10

BATTERY CHAPTER 10: MAINTENANCE
10.12.2.11 IT Smaltimento batterie

Questo prodotto contiene una batteria che non può essere smaltita nei comuni contenitori per lo smaltimento rifiuti, nell'
Unione Europea. Controllate la documentazione del prodotto per le informazioni specifiche sulla batteria. La batteria è
contrassegnata con questo simbolo e può includere alcuni caratteri ad indicare la presenza di cadmio (Cd), piombo (Pb)
oppure mercurio (Hg). Per il corretto smaltimento, potete restituirli al vostro fornitore locale, oppure rivolgervi e consegnarli
presso i centri di raccolta preposti. Per maggiori informazioni vedere: ww.recyclethis.info.
10.12.2.12 LT Baterijų šalinimas

Šios įrangos sudėtyje yra baterijų, kurias draudžiama šalinti Europos Sąjungos viešose nerūšiuotų atliekų šalinimo
sistemose. Informaciją apie baterijas galite rasti įrangos techninėje dokumentacijoje. Baterijos žymimos šiuo simboliu,
papildomai gali būti nurodoma kad baterijų sudėtyje yra kadmio (Cd), švino (Pb) ar gyvsidabrio (Hg). Eksploatavimui
nebetinkamas baterijas pristatykite į tam skirtas surinkimo vietas arba grąžinkite jas tiesioginiam tiekėjui, kad jos būtų
tinkamai utilizuotos. Daugiau informacijos rasite šioje interneto svetainėje: www.recyclethis.info.
10.12.2.13 LV Bateriju likvidēšana

Šis produkts satur bateriju vai akumulatoru, kuru nedrīkst izmest Eiropas Savienībā esošajās sadzīves atkritumu sistēmās.
Sk. produkta dokumentācijā, kur ir norādīta konkrēta informācija par bateriju vai akumulatoru. Baterijas vai akumulatora
marķējumā ir šis simbols, kas var ietvert burtus, kuri norāda kadmiju (Cd), svinu (Pb) vai dzīvsudrabu (Hg). Pēc
ekspluatācijas laika beigām baterijas vai akumulatori jānodod piegādātājam vai specializētā bateriju savākšanas vietā.
Sīkāku informāciju var iegūt vietnē: www.recyclethis.info.
10.12.2.14 NL Verwijderen van baterijen

Dit product bevat een batterij welke niet kan verwijdert worden via de gemeentelijke huisvuilscheiding in de Europese
Gemeenschap. Gelieve de product documentatie te controleren voor specifieke batterij informatie. De batterijen met deze
label kunnen volgende indictaies bevatten cadium (Cd), lood (Pb) of kwik (Hg). Voor correcte vorm van kringloop, geef je de
producten terug aan jou locale leverancier of geef het af aan een gespecialiseerde verzamelpunt. Meer informatie vindt u
op de volgende website: www.recyclethis.info.
10.12.2.15 NO Retur av batteri

Dette produkt inneholder et batteri som ikke kan kastes med usortert kommunalt søppel i den Europeiske Unionen. Se
produktdokumentasjonen for spesifikk batteriinformasjon. Batteriet er merket med dette symbolet som kan inkludere
symboler for å indikere at kadmium (Cd), bly (Pb), eller kvikksølv (Hg) forekommer. Returner batteriet til leverandøren din
eller til et dedikert oppsamlingspunkt for korrekt gjenvinning. For mer informasjon se: www.recyclethis.info.
10.12.2.16 PL Pozbywanie się zużytych baterii

Ten produkt zawiera baterie, które w Unii Europejskiej mogą być usuwane tylko jako posegregowane odpady komunalne.
Dokładne informacje dotyczące użytych baterii znajdują się w dokumentacji produktu. Baterie oznaczone tym symbolem
mogą zawierać dodatkowe oznaczenia literowe wskazujące na zawartość kadmu (Cd), ołowiu (Pb) lub rtęci (Hg). Dla
zapewnienia właściwej utylizacji, należy zwrócić baterie do dostawcy albo do wyznaczonego punktu zbiórki. Więcej
informacji można znaleźć na stronie internetowej www.recyclethis.info.
10.12.2.17 PT Eliminação de Baterias

Este produto contêm uma bateria que não pode ser considerado lixo municipal na União Europeia. Consulte a
documentação do produto para obter informação específica da bateria. A bateria é identificada por meio de este símbolo,
que pode incluir a rotulação para indicar o cádmio (Cd), chumbo (Pb), ou o mercúrio (hg). Para uma reciclagem apropriada
envie a bateria para o seu fornecedor ou para um ponto de recolha designado. Para mais informação veja:
www.recyclethis.info.
10

CHAPTER 10: MAINTENANCE CLEAR FILES AND DATA AFTER UNINSTALL
10.12.2.18 RU Утилизация батарей

Согласно европейской директиве об отходах электрического и электронного оборудования, продукты, содержащие
батареи, нельзя утилизировать как обычные отходы на территории ЕС. Более подробную информацию вы найдете в
документации к продукту. На этом символе могут присутствовать буквы, которые означают, что батарея собержит
кадмий (Cd), свинец (Pb) или ртуть (Hg). Для надлежащей утилизации по окончании срока эксплуатации пользователь
должен возвратить батареи локальному поставщику или сдать в специальный пункт приема. Подробности можно
найти на веб-сайте: www.recyclethis.info.
10.12.2.19 SK Zaobchádzanie s batériami

Tento produkt obsahuje batériu, s ktorou sa v Európskej únii nesmie nakladať ako s netriedeným komunálnym odpadom.
Dokumentácia k produktu obsahuje špecifické informácie o batérii. Batéria je označená týmto symbolom, ktorý môže
obsahovať písmená na označenie kadmia (Cd), olova (Pb), alebo ortuti (Hg). Na správnu recykláciu vráťte batériu vášmu
lokálnemu dodávateľovi alebo na určené zberné miesto. Pre viac informácii pozrite: www.recyclethis.info.
10.12.2.20 SL Odlaganje baterij

Ta izdelek vsebuje baterijo, ki je v Evropski uniji ni dovoljeno odstranjevati kot nesortiran komunalni odpadek. Za posebne
informacije o bateriji glejte dokumentacijo izdelka. Baterija je označena s tem simbolom, ki lahko vključuje napise, ki
označujejo kadmij (Cd), svinec (Pb) ali živo srebro (Hg). Za ustrezno recikliranje baterijo vrnite dobavitelju ali jo odstranite na
določenem zbirališču. Za več informacij obiščite spletno stran: www.recyclethis.info.
10.12.2.21 SV Kassering av batteri

Denna produkt innehåller ett batteri som inte får kastas i allmänna sophanteringssytem inom den europeiska unionen. Se
produktdokumentationen för specifik batteriinformation. Batteriet är märkt med denna symbol, vilket kan innebära att det
innehåller kadmium (Cd), bly (Pb) eller kvicksilver (Hg). För korrekt återvinning skall batteriet returneras till leverantören eller
till en därför avsedd deponering. För mer information, se: www.recyclethis.info.
10.12.2.22 TR Pil Geri Dönüşümü

Bu ürün Avrupa Birliği genel atık sistemlerine atılmaması gereken pil içermektedir. Daha detaylı pil bilgisi için ürünün
kataloğunu inceleyiniz. Bu sembolle işaretlenmiş piller Kadmiyum(Cd), Kurşun(Pb) ya da Civa(Hg) içerebilir. Doğru geri
dönüşüm için ürünü yerel tedarikçinize geri veriniz ya da özel işaretlenmiş toplama noktlarına atınız. Daha fazla bilgi için:
www.recyclethis.info.
10.12.2.23 Global contacts

North America 905-294-6222
Latin America +55 11 3614 1700
Europe, Middle East, Africa +(34) 94 485 88 00
Asia +86-21-2401-3208
India +91 80 41314617
From GE Part Number 1604-0021-A1, GE Publication Number GEK-113574.
10.13 Clear files and data after uninstall

The unit can be decommissioned by turning off power to the unit and disconnecting the wires to it.
To clear files and settings in the UR:
1. On the UR front panel, navigate to COMMANDS  RELAY MAINTENANCE  SERVICE COMMAND, enter the value 20511,
and press the ENTER key. The relay restarts and clears the UR.
2. Clear the flash memory using the SETTINGS  PRODUCT SETUP  CLEAR RELAY RECORDS command.
10

REPAIRS CHAPTER 10: MAINTENANCE
To clear files and settings on the computer:

1. Uninstall the EnerVista UR Setup software.
2. Find and delete the following UR files:
– .URS, .CID, and .ICD settings
– .EVT event records
– .CFG and .DAT COMTRADE
10.14 Repairs
The battery and modules inside the case can be replaced without return of the device to the factory. The firmware and
software can be upgraded without return of the device to the factory.
Fuses in the power supply module are not field-replaceable.
Files can be requested for use by technical support staff, for example the Service Report (click the icon in the software or
connect a USB drive to the graphical front panel) or under Maintenance > Retrieve File, as outlined elsewhere in this
document.
For issues not solved by troubleshooting, the process to return the device to the factory for repair is as follows:
• Contact a GE Grid Solutions Technical Support Center. Contact information is found in the first chapter.
• Obtain a Return Materials Authorization (RMA) number from the Technical Support Center.
• Verify that the RMA and Commercial Invoice received have the correct information.
• Tightly pack the unit in a box with bubble wrap, foam material, or styrofoam inserts or packaging peanuts to cushion
the item(s). You may also use double boxing whereby you place the box in a larger box that contains at least 5 cm of
cushioning material.
• Ship the unit by courier or freight forwarder, along with the Commercial Invoice and RMA, to the factory.
GE GRID SOLUTIONS
650 MARKLAND STREET
MARKHAM, ONTARIO
CANADA L6C 0M1
ATTN: SERVICE DEPT.
RMA# : ______________
Customers are responsible for shipping costs to the factory, regardless of whether the unit is under warranty.
• Fax a copy of the shipping information to the GE Grid Solutions service department in Canada at +1 905 927 5098.
Use the detailed return procedure outlined at
https://www.gegridsolutions.com/multilin/support/ret_proc.htm
The current warranty and return information are outlined at
https://www.gegridsolutions.com/multilin/warranty.htm
10.15 Storage
Store the unit indoors in a cool, dry place. If possible, store in the original packaging. Follow the storage temperature range
outlined in the Specifications.
10

CHAPTER 10: MAINTENANCE DISPOSAL
10.16 Disposal
Other than the battery, there are no special requirements for disposal of the unit at the end its service life. For customers
located in the European Union, dispose of the battery as outlined earlier. To prevent non-intended use of the unit, remove
the modules, dismantle the unit, and recycle the metal when possible.
10

DISPOSAL CHAPTER 10: MAINTENANCE
10

Appendix A: FlexAnalog operands
Appendices
FlexAnalog operands
This appendix outlines FlexAnalog parameters.
A.1 FlexAnalog items

A FlexAnalog parameter is an analog parameter.
FlexAnalog items specific to your device are viewable in a web browser. Enter the IP address of the UR, access the Device
Information Menu option, then the FlexAnalog Parameter Listing option. Entries displayed online depend on order code.
The following addresses are given for the maximum number of physical channels. For example, if there are 7 CT
channels in the CT/VT module, that address 28437 corresponds to the "L1 Current Mag" value.
Table A-1: B90 FlexAnalog data items

Address FlexAnalog name Units Description
8656 Bus 1 Diff Mag Amps B90 bus zone DMag
8660 Bus 1 Diff Angle Degrees B90 bus zone diff angle
8661 Bus 1 Rest Mag Amps B90 bus zone restraint RMag
8663 Bus 1 Rest Angle Degrees B90 bus zone rest angle
8664 Bus 1 Max CT Amps B90 bus max CT
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL A-1

FLEXANALOG ITEMS APPENDIX A: FLEXANALOG OPERANDS

A 8705 Bus 4 Rest Angle Degrees B90 bus zone rest angle
9493 Bus Max CT Primary Amps Bus maximum CT primary
12306 Oscill Num Triggers --- Oscillography number of triggers
14189 PTP–IRIG-B Delta ns PTP time minus IRIG-B time
24432 Communications Group --- Groups communications group
24447 Active Setting Group --- Current setting group
28416 F1 Curr Mag Amps Terminal 1 current magnitude
28418 F1 Curr Ang Degrees Terminal 1 current angle
28428 M1 Curr Mag Amps Terminal 5 current magnitude
28430 M1 Curr Ang Degrees Terminal 5 current angle
28440 L1 Curr Mag Amps Terminal 9 current magnitude
28442 L1 Curr Ang Degrees Terminal 9 current angle
A-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

APPENDIX A: FLEXANALOG OPERANDS FLEXANALOG ITEMS
A
28464 S1 Curr Mag Amps Terminal 17 current magnitude
28466 S1 Curr Ang Degrees Terminal 17 current angle
28488 F5 Volt Mag Volts Terminal 1 voltage magnitude
28490 F5 Volt Ang Degrees Terminal 1 voltage angle
28500 M5 Volt Mag Volts Terminal 5 voltage magnitude
28502 M5 Volt Ang Degrees Terminal 5 voltage angle
28512 S1 Volt Mag Volts Terminal 9 voltage magnitude
28514 S1 Volt Ang Degrees Terminal 9 voltage angle
28624 System Frequency Hz Terminal frequency
32768 Tracking Frequency Hz Terminal tracking frequency
45584 RxGOOSE Analog 1 --- RxGOOSE analog input 1
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL A-3

FLEXANALOG ITEMS APPENDIX A: FLEXANALOG OPERANDS

A 45590 RxGOOSE Analog 4 --- RxGOOSE analog input 4
63634 Bus 1 M_Id --- B90 Bus M_Id
63636 Bus 1 M_Ir --- B90 Bus M_Ir
63638 Bus 1 d_Ir --- B90 Bus d_Ir
A-4 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Appendix B: RADIUS server configuration
RADIUS server configuration
This appendix outlines how to set up a RADIUS server for user authentication.
B.1 RADIUS server configuration

The following procedure is an example of how to set up a simple RADIUS server. You install the RADIUS server software on
a separate computer. In this example, we use FreeRADIUS third-party software.
1. Download and install FreeRADIUS from www.freeradius.net as the RADIUS server. This is a Windows 32-bit installation
that is known to work. If you try another third-party tool and it does not work, use the FreeRADIUS software from
freeradius.net.
2. Open the radius.conf file in the <Path_to_Radius>\etc\raddb folder, locate the "bind_address" field, and enter your
RADIUS server IP address. An example is
bind_address = 10.14.61.109
Text editor software that supports direct editing and saving of UNIX text encodings and line breaks, such as EditPad
Lite, is needed for this editing.
3. In the users.conf file in the <Path_to_Radius>\etc\raddb folder, add the following text to configure a user "Tester" with
an Administrator role.
Tester User-Password == "testpw"
GE-PDC-USER-Role = Administrator,
4. In the clients.conf file in the <Path_to_Radius>\etc\raddb folder, add the following text to define the UR as a RADIUS
client, where the client IP address is 10.0.0.2, the subnet mask is 255.255.255.0, the shared secret specified here is also
configured on the UR device for successful authentication, and the shortname is a short, optional alias that can be
used in place of the IP address.
client 10.0.0.2/24 {
secret = testing123
shortname = private-network-1
}
5. In the <Path_to_Radius>\etc\raddb folder, create a file called dictionary.ge and add the following content.
# ##########################################################
# GE VSAs
############################################################
VENDOR GE 2910
# Management authorization
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL B-1

RADIUS SERVER CONFIGURATION APPENDIX B: RADIUS SERVER CONFIGURATION
BEGIN-VENDOR GE
# Role ID
ATTRIBUTE GE-UR-Role 1 integer
# GE-UR-ROLE values
VALUE GE-UR-Role Administrator 1
VALUE GE-UR-Role Supervisor 2
VALUE GE-UR-Role Engineer 3
B VALUE GE-UR-Role
VALUE GE-UR-Role
Operator
Observer
4
5
END-VENDOR GE
#############################################################
6. In the dictionary file in the <Path_to_Radius>\etc\raddb folder, add the following line.
$INCLUDE dictionary.ge
For example, the file can look like the following:
$INCLUDE ../shareéfreeradius/dictionary
$INCLUDE dictionary.ge
7. For the first start, run the RADIUS server in debug mode to ensure that there are no compiling errors.
<Path_to_Radius>/start_radiusd_debug.bat
8. Set up the RADIUS parameters on the UR as follows.
8.1. If logging in, select Device for the Authentication Type, and use Administrator for the User Name. The default
password is "ChangeMe1#".
8.2. Access Settings > Product Setup > Security. Configure the IP address and ports for the RADIUS server. Leave
the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the clients.conf
file. Restart the relay for the IP address and port changes to take effect.
9. Verify operation. Log in to the UR software as follows. In the login window, select Server as the Authentication Type,
enter the user name entered (for example user name Tester and password "testpw"). Check that the RADIUS server log
file shows the access with an "Access-Accept" entry.
Recall that if you tried another third-party tool and it did not work, you can use the FreeRADIUS software from
freeradius.net.
B-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Appendix C: Command line interface
Command line interface
This appendix outlines command line access to the software.
C.1 Command line interface

SetupCLI is a command line interface to communicate with the EnerVista UR Setup software. Commands can be sent from
a DOS prompt or a Windows batch file.
The interface is installed with the EnerVista software. Its default location is similar to
C:\Program Files\EnerVista\Tools\SetupCLI
The EnerVista software needs to be installed on a computer to run the command line interface. The command line
interface does not provide a remote connection to a computer running the EnerVista software.
Items to note are as follows:
• Works with EnerVista UR Setup version 6.10 and later
• Available in English only
• The graphical user interface of the software is not available concurrently with the command line interface
• It does not support concurrent commands
• It has limited functionality with CyberSentry
• It does not interface with UR Engineer
• It does not work when EnerVista UR Setup security is enabled, meaning when login is required
Command syntax is as follows:
• Options enclosed in [ ] are optional
• Values enclosed in < > are replaced with your own values
• <Application> is replaced with the EnerVista software to receive the command. Use "URPC" for EnerVista UR Setup.
• <device> is the UR device name, as displayed in the Device Name field of the Device Setup window and listed in the
Online Window. Use quotes with spaces, such as "B30 Belfort".
• "-s" can be used with any command to suppress error messages
• All commands, their return codes, and error description are logged in the file
C:\ProgramData\EnerVista\Tools\SetupCLI\SetupCLI.log
• When the Supervisor account is enabled, the 'Lock Relay' setting must first be changed to No before the putsettings,
inservice, or reboot command can be used. This setting cannot be changed using the command line interface.
• Use quotes ("") to enclose any parameter containing a space
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL C-1

COMMAND LINE INTERFACE APPENDIX C: COMMAND LINE INTERFACE
• Commands, options, and parameters are case sensitive

• All commands have a return code of 0-255. 0 indicates success and 1-255 indicate different errors
• If SetupCLI is automated (in a batch file), make sure that only a single batch is running at a time. SetupCLI does not
support concurrent operations.
To run the command line interface:

1. In Windows, click the Start button, enter cmd, and press the Enter key. After prompting for permission, the Windows
command window opens.
2. Enter SetupCLI followed by the action to execute. An example of use is to enter "SetupCLI -h" to display help,
specifically the commands and explanations outlined here.
Figure C-1: Command line interface run in the command window
C
SetupCLI -h
Display help.
It displays the content outline here.
SetupCLI <Application> start [-c] [-s]

Launch application with name <Application>.
To start in client mode, which is the graphical user interface, include option '-c'. Before use, the software must be idle
without any windows open. Any activity or open windows can cause unexpected behavior. When in client mode, do not
use Launchpad's Site Management feature.
To suppress errors, include option -s.
Example: SetupCLI URPC start -c
SetupCLI <Application> exit [-s]

Exit application with name <Application>.
Example: SetupCLI URPC exit
SetupCLI <Application> login -d <device> [-A <authentication type>] [-a <account>] -w <password> [-s]
Authenticate with device <device> using password <password>.
For non-CyberSentry devices — Set <authentication type> to "traditional". Note that <authentication type> defaults to
"traditional" if not specified. Set <account> to "COMMANDS" or "SETTINGS". If not specified, the SETTINGS account is
used.
Example: SetupCLI URPC login -d "C30 Melbourne" -A traditional -a SETTINGS -w 1password1
C-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

APPENDIX C: COMMAND LINE INTERFACE COMMAND LINE INTERFACE
Example of a batch file that checks for an error (this batch file uses standard batch file operations to check the return
code (ERRORLEVEL) and jump to an error handler):
SetupCLI URPC start
SetupCLI URPC login -d demoDevice -a SETTINGS -w WrongPassword -A traditional
IF NOT ERRORLEVEL 0 GOTO FAILED
SetupCLI URPC putsettings -d demoDevice -f "example file.urs"
SetupCLI URPC inservice -d demoDevice
SetupCLI URPC reboot -d demoDevice
SetupCLI URPC exit
exit
:FAILED
echo Please try again C
exit
For CyberSentry devices with local authentication — Set <authentication type> to "local" . Set <account> to
"Supervisor", "Administrator", "Engineer", "Operator", or "Observer".
For CyberSentry devices with RADIUS authentication — Set <authentication type> to "radius". Set <account> to the
user's account on the RADIUS server.
SetupCLI <Application> logout -d <device> [-s]

Log out of device <device>.
Example: SetupCLI URPC logout -d C30
SetupCLI <Application> getsettings -d <device> -f <File> [-s]

Read settings from device <device> and save them to the .urs file <File>. The <File> must not already exist. The default
path to the output file is C:\Users\Public\Public Documents\GE Power Management\URPC\Data
Example: SetupCLI URPC getsettings -d C30 -f "C30 Markham.urs"
Example of a batch file to retrieve a settings file:
SetupCLI URPC start
SetupCLI URPC getsettings -d demoDevice -f C:\example.urs
SetupCLI URPC exit
Example of a batch file to retrieve a settings file from a relay that requires RADIUS authentication:
SetupCLI URPC start
SetupCLI URPC login -d demoDevice -a %1 -w %2 -A radius
SetupCLI URPC getsettings -d demoDevice -f "example file.urs"
SetupCLI URPC logout -d demoDevice
SetupCLI URPC exit
Although a user name and password could have been entered in this batch file, it would have created a security risk.
Batch files allow you to pass in runtime parameters and refer to them in your script as %1, %2, and so on. For example,
if this file is called example.bat, one calls it as follows: "example.bat MyUserName MyPassword"
SetupCLI <Application> putsettings -d <device> -f <File> [-s]

Write the settings file <File> to the device <device>.
For CyberSentry devices, putsettings is only supported for users with the "Administrator" role.
Example: SetupCLI URPC putsettings -d C30 -f "C30 Markham.urs"

SetupCLI <Application> compare -f <File1> -r <File2> -o <OutputFile> [-s]

Compare settings files <File1> and <File2>, and save output to <OutputFile>.
Example: SetupCLI URPC compare -f may.urs -r september.urs -o compared.txt
Batch file example that retrieves a settings file, compares it with an existing settings file, and opens the resulting
comparison file:
SetupCLI URPC start
SetupCLI URPC getsettings -d demoDevice -f devicefile.urs
SetupCLI URPC compare -f existingfile.urs -r devicefile.urs -o output.txt
The output is similar to the following:

Comparing settings file aaa.urs : C:\Users\Public\Public Documents\GE Power Management\URPC\Data\ with bbb.urs
: C:\Users\Public\Public Documents\GE Power Management\URPC\Data\
C
# Setting Name (Group,Module,Item) Value
1 + Default Message Timeout (1,1,1) = 299 s

2 - Default Message Timeout (1,1,1) = 300 s
3 + Flash Message Time (1,1,1) = 0.9 s
4 - Flash Message Time (1,1,1) = 1.0 s
SetupCLI <Application> inservice -d <device> [-n] [-s]

Put the device in service. Include option -n to take the device out of service.
Example: SetupCLI URPC inservice -d C30
SetupCLI <Application> reboot -d <device> [-s]

Reboot the relay <device>. This is necessary after changing IEC 61850 settings and aggregator source settings.
Example: SetupCLI URPC reboot -d "C30_Instanbul"
SetupCLI <Application> adddevice -I <IP Address> -S <Slave Address> -P <Modbus Port>

Connect to a device using its IP address, slave address, and Modbus port. Show the device in the EnerVista interface
under the SetupCLI Site as DEV@SETUP_CLI.
EnerVista UR Setup 7.30 or higher supports this command.
Figure C-2: Device added using IP address
The device is named as DEV@SETUP_CLI, which is used as the device name required by the <device> parameter of other
SetupCLI commands.

APPENDIX C: COMMAND LINE INTERFACE COMMAND LINE INTERFACE
The device name DEV@SETUP_CLI is always assigned to the device that is connected most recently by performing
'adddevice' command. It means that the Application only keeps up to one device named as DEV@SETUP_CLI, the
'adddevice' command disconnects/deletes the device DEV@SETUP _CLI that was connected previously by performing
'adddevice' command.
The device name DEV@SETUP_CLI is never used to configure/connect to a device through the graphical user interface.
Example of a batch file using a device IP address to retrieve its settings file:
SetupCLI URPC start
SetupCLI URPC adddevice -I 192.168.140.113 -S 113 -P 502
SetupCLI URPC getsettings -d DEV@SETUP_CLI -f C:\example.urs
SetupCLI URPC exit
After connecting the device using IP address, the device name DEV@SETUP_CLI is used to identify this device in
'getsettings' command.
Example of a batch file using a device IP address to retrieve a settings file when RADIUS authentication is required: C
SetupCLI URPC start
SetupCLI URPC adddevice -I 192.168.140.113 -S 113 -P 502
SetupCLI URPC login -d DEV@SETUP_CLI -a %1 -w %2 -A radius
SetupCLI URPC getsettings -d DEV@SETUP_CLI -f "example file.urs"
SetupCLI URPC logout -d DEV@SETUP_CLI
SetupCLI URPC exit
DEV@SETUP_CLI has to be used as the device name in the commands followed by the 'adddevice' command.


Appendix D: Miscellaneous
Miscellaneous
This chapter provides the warranty and revision history.
D.1 Warranty
For products shipped as of 1 October 2013, GE Grid Solutions warrants most of its GE manufactured products for 10 years.
For warranty details including any limitations and disclaimers, see the Terms and Conditions at
http://www.gegridsolutions.com/multilin/warranty.htm
For products shipped before 1 October 2013, the standard 24-month warranty applies.
D.2 Revision history

The tables outline the releases and revision history of this document.
Table D-1: Revision history (English)
Manual P/N B90 revision Release date ECO
1601-0115-C1 3.0x 02 July 2002 URB-006
1601-0115-C2 3.0x 18 November 2002 URB-011
1601-0115-C3 3.0x 30 August 2003 URB-009
1601-0115-G1 4.0x 23 March 2004 URX-123
1601-0115-G2 4.0x 17 May 2004 URX-136
1601-0115-K1 4.6x 15 February 2005 URX-176
1601-0115-M1 4.9x 15 December 2005 URX-208
1601-0115-M2 4.9x 27 February 2006 URX-214
1601-0115-P1 5.2x 28 February 2007 URX-236
1601-0115-P2 5.2x 01 March 2007 URX-236
1601-0115-R1 5.4x 26 June 2007 URX-242
1601-0115-R2 5.4x 31 August 2007 URX-246
1601-0115-R3 5.4x 17 October 2007 URX-251
1601-0115-S1 5.5x 7 December 2007 URX-253
1601-0115-S2 5.5x 22 February 2008 URX-258
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL D-1

REVISION HISTORY APPENDIX D: MISCELLANEOUS
Manual P/N B90 revision Release date ECO

1601-0115-S3 5.5x 12 March 2008 URX-260
1601-0115-T1 5.6x 27 June 2008 08-0390
1601-0115-U1 5.7x 29 May 2009 09-0938
1601-0115-U2 5.7x 30 September 2009 09-1165
1601-0115-V1 5.8x 29 May 2010 09-1457
1601-0115-V2 5.8x 04 January 2011 11-2237
1601-0115-W1 5.9x 12 January 2011 11-2227
1601-0115-X1 6.0x 21 December 2011 11-2840
1601-0115-X2 6.0x 5 April 2012 12-3254
1601-0115-Y1 7.0x 30 September 2012 12-3529
1601-0115-Y2 7.0x 11 November 2012 12-3601
1601-0115-Z1 7.1x 30 March 2013 13-0126
1601-0115-AA1 7.2x 1 August 2013 13-0401
1601-0115-AB1 7.3x 7 November 2014 14-1408
1601-0115-AB2 7.3x 1 September 2015 15-2215
D 1601-0115-AC1
1601-0115-AE1
7.40x
7.41x
8 December 2016
31 January 2017
16-3319
17-3427
1601-0115-AE3 7.4x 28 April 2017 17-3561
1601-0115-AF1 7.6x 30 June 2017 17-3779
1601-0115-AF2 7.6x 31 October 2017 17-3935
1601-0115-AG1 7.7x 31 March 2018 18-4430
1601-0115-AG2 7.7x 4 May 2018 18-4517
Table D-2: Major changes for B90 manual version AG2 (English)
Page Description
--- General revision. Improved figure quality by using conditional text to switch between PDF and PNG figures.
Table D-3: Major changes for B90 manual version AG1 (English)
Page Description
--- General revision
2-9 Updated order codes from SH / SL to RH / RL for the redundant power supply for UR purchase. The power supply modules
were upgraded in 2014 to SH and SL, but the order codes when purchasing a UR remain as RH and RL so that customers do
not need to change order codes. The order codes for the power supply replacement modules are correct as SH and SL.
3-56 Added IP and subnet mask address rules to the Set IP Address in UR section
5-53 Added IEC 61850 Editions 1 and 2 section
5-103 Added support for a redundant SNTP server as a time source
5-149 Added GOOSE simulation operands to FlexLogic operands table
5-204 Added Settings > Simulation > GOOSE section
6-3 Added Actual Values > Graphical Panel > LEDs and Pushbuttons information
6-10 Added Actual Values > Status > Protocol section
Table D-4: Major changes for B90 manual version AF2 (English)
Page Description
--- Added type W CPU module to order codes in chapter 2, installation chapter 3, Replace Front Panel section in chapter 10
D-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

APPENDIX D: MISCELLANEOUS REVISION HISTORY
Page Description
--- Added Japanese and Polish languages and modules 6W and 6X to order codes in chapter 2. Module 6W allows 30 contact
inputs, and Module 6X allows 18 outputs.
3-16 Added contact input and contact output modules 6W and 6X to Table 3-3 Contact Input and Output Module Assignments and
to Figure 3-16 Contact Input and Output Module Wiring (Sheet 3 of 3)
Table D-5: Major changes for B90 manual version AF1 (English)
Page Description
--- Updated "faceplate" to "front panel" for consistency and to reflect web site
--- Added graphical front panel option to order codes and specifications in chapter 2, Interfaces chapter 4, Settings chapter 5,
Actual Values chapter 6
--- Added PEAP-GTC and PAP protocols for authenticating user logins when using a RADIUS server. Added to Settings > Product
Setup > Security > RADIUS Authentication Method and to Modbus memory map and F codes.
--- Updated Contact Inputs from 96 to 120 and Contact Outputs from 64 to 72 in Product Description in chapter 2 and FlexLogic
operands table in chapter 5
3-36 Updated RS422 and Fiber Interface Connection figure for the clock channels (from 7a and 7b to 1a and 1b)
3-67 Added Connect to a D400 Gateway section
4-42
4-50
Updated LED Labelling instructions for the new Front Panel Label Designer
Added Standard Front Panel section for labelling LEDs and pushbuttons
D
5-98 Added USB Port section to enable/disable the USB port on the graphical front panel
5-110 Updated User-programmable Pushbuttons section as per specifications
10-5 Added Convert Device Settings section
10-7 Added Copy Settings to Other Device section
10-15 Added Replace Front Panel section for retrofit with the new graphical front panel
Table D-6: Major changes for B90 manual version AE3 (English)
Page Description
2- Updated order codes
10-5 Added Copy Settings to Other Device section
Table D-7: Major changes for B90 manual version AE1 (English)
Page Description
--- Added routable GOOSE content in chapters 2 and 5
3-34 Updated RS422 and Fiber Interface Connection figure for the clock channels (from 7a and 7b to 1a and 1b)
4- Added Engineer content
5- Updated IEC 61850 content
A- Updated FlexAnalog table for most UR products
Table D-8: Major changes for B90 manual version AC1 (English)
Page Description
--- General revision. Added online help and updated generic online help.
--- Deleted EAC logo from title page and deleted EAC certification from Approvals specifications because document not
translated into Russian
--- Updated number of Direct Inputs / Direct Outputs, increasing them from 96 to 256, in specifications, FlexLogic operands table,
settings, actual values, Modbus memory map
2- Updated several specifications, such as TOC, IOC, number of FlexLogic lines
4-28 Added FlexLogic Design and Monitoring using Engineer section to end of Interfaces chapter
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL D-3

REVISION HISTORY APPENDIX D: MISCELLANEOUS
Page Description
5-38 Added PRT FUNCTION settings in Network section to enable/disable each Ethernet port
5-47 Updated IEC 61850 section
5-58 Added Support for Routable GOOSE section
5-143 Updated number of FlexLogic lines from 512 to 1024 in FlexLogic Equation Editor settings section
10-1 Added Monitoring section
10-2 Added Retrieve Files section
C- Added Command Line Interface appendix
D-4 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Glossary
Abbreviations
CPU Central Processing Unit

Abbreviations
A Ampere
AC Alternating Current CRC Cyclic Redundancy Code/Check
A/D Analog to Digital CRL Certificate Revocation List
AE Accidental Energization, Application Entity CRT, CRNT Current
AMP Ampere CSA Canadian Standards Association
ANG Angle CT Current Transformer
ANSI American National Standards Institute CVT Capacitive Voltage Transformer
AR Automatic Reclosure
ARP Address Resolution Protocol D/A Digital to Analog
ASDU Application-layer Service Data Unit DC (dc) Direct Current
ASYM Asymmetry DCE Data Communications Equipment
AUTO Automatic DCS Distributed Control System
AUX Auxiliary DD Disturbance Detector
AVG Average DFLT Default
AWG American Wire Gauge DGNST Diagnostics
DIFF Differential
BCS Best Clock Selector DIR Directional
BER Bit Error Rate DISCREP Discrepancy
BF Breaker Fail DIST Distance
BFI Breaker Failure Initiate DMD Demand
BKR Breaker DNP Distributed Network Protocol
BLK Block DPO Dropout
BLKG Blocking DPS Double-Point Status
BNC Bayonet Neill-Concelman DSP Digital Signal Processor
BPNT Breakpoint of a characteristic DST Daylight Savings Time
BRKR Breaker dt Rate of Change
DTT Direct Transfer Trip
CA Certificate Authority DUTT Direct Under-reaching Transfer Trip
CAP Capacitor
CC Coupling Capacitor EGD Ethernet Global Data
CCVT Coupling Capacitor Voltage Transformer ENCRMNT Encroachment
CFG Configure / Configurable EPRI Electric Power Research Institute
.CFG Filename extension for oscillography files .EVT Filename extension for event recorder files
CHK Check EXT Extension, External
CHNL Channel
CID Configured IED Description F Field
CLS Close FAIL Failure
CLSD Closed FD Fault Detector
CMND Command FDH Fault Detector high-set
CMPRSN Comparison FDL Fault Detector low-set
CO Contact Output FIR Finite Impulse Response
COM Communication FLA Full Load Current
COMM Communications FO Fiber Optic
COMP Compensated, Comparison FPGA Field-programmable Gate Array
CONN Connection FREQ Frequency
CONT Continuous, Contact FSK Frequency-Shift Keying
CO-ORD Coordination FTP File Transfer Protocol
FxE FlexElement™
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL i

ABBREVIATIONS
FWD Forward M2M Machine to Machine

mA MilliAmpere
G Generator MAG Magnitude
GCM Galois Counter Mode MAN Manual / Manually
GDOI Group Domain of Interpretation MAX Maximum
GE General Electric Mb Megabit
GFP Graphical Front Panel MIC Model Implementation Conformance
GND Ground MIN Minimum, Minutes
GNTR Generator MMI Man Machine Interface
GoCB GOOSE Control Block MMS Manufacturing Message Specification
GOOSE General Object Oriented Substation Event MRT Minimum Response Time
GPS Global Positioning System MSG Message
GSU Generator Step-Up MTA Maximum Torque Angle
MTR Motor
HARM Harmonic / Harmonics MVA MegaVolt-Ampere (total 3-phase)
HCT High Current Time MVA_A MegaVolt-Ampere (phase A)
HGF High-Impedance Ground Fault (CT) MVA_B MegaVolt-Ampere (phase B)
HIZ High-Impedance and Arcing Ground MVA_C MegaVolt-Ampere (phase C)
HMI Human-Machine Interface MVAR MegaVar (total 3-phase)
HTTP Hyper Text Transfer Protocol MVAR_A MegaVar (phase A)
HV High Voltage MVAR_B MegaVar (phase B)
HYB Hybrid MVAR_C MegaVar (phase C)
Hz Hertz MVARH MegaVar-Hour
MW MegaWatt (total 3-phase)
I Instantaneous MW_A MegaWatt (phase A)
I_0 Zero Sequence current MW_B MegaWatt (phase B)
I_1 Positive Sequence current MW_C MegaWatt (phase C)
I_2 Negative Sequence current MWH MegaWatt-Hour
IA Phase A current
IAB Phase A minus B current N Neutral
IB Phase B current N/A, n/a Not Applicable
IBC Phase B minus C current NEG Negative
IC Phase C current NMPLT Nameplate
ICA Phase C minus A current NOM Nominal
ICD IED Capability Description NTR Neutral
ID Identification
IED Intelligent Electronic Device O Over
IEC International Electrotechnical Commission OC, O/C Overcurrent
IEEE Institute of Electrical and Electronic Engineers OCSP Online Certificate Status Protocol
IG Ground (not residual) current OF Overload Factor
Igd Differential Ground current O/P, Op Output
IGMP Internet Group Management Protocol OP Operate
IID Instantiated IED Capability Description OPER Operate
IN CT Residual Current (3Io) or Input OPERATG Operating
INC SEQ Incomplete Sequence O/S Operating System
INIT Initiate OSI Open Systems Interconnect
INST Instantaneous OSB Out-of-Step Blocking
INV Inverse OUT Output
I/O Input/Output OV Overvoltage
IOC Instantaneous Overcurrent OVERFREQ Overfrequency
IOV Instantaneous Overvoltage OVLD Overload
IRC Inter-Relay Communication
IRIG Inter-Range Instrumentation Group P Phase
ISO International Standards Organization PC Phase Comparison, Personal Computer
IUV Instantaneous Undervoltage PCNT Percent
PF Power Factor (total 3-phase)
K0 Zero Sequence Current Compensation PF_A Power Factor (phase A)
kA kiloAmpere PF_B Power Factor (phase B)
KDC Key Distribution Center PF_C Power Factor (phase C)
kV kiloVolt PFLL Phase and Frequency Lock Loop
PHS Phase
LCD Liquid Crystal Display PICS Protocol Implementation & Conformance
LED Light Emitting Diode Statement
LEO Line End Open PKI Public Key Infrastructure
LFT BLD Left Blinder PKP Pickup
LOOP Loopback PLC Power Line Carrier
LPU Line Pickup POS Positive
LRA Locked-Rotor Current POTT Permissive Over-reaching Transfer Trip
LTC Load Tap-Changer PRESS Pressure
LV Low Voltage PRI Primary
PROT Protection
M Machine PRP Parallel Redundancy Protocol
ii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

ABBREVIATIONS
PSEL Presentation Selector TRANSF Transfer

PTP Precision Time Protocol TSEL Transport Selector
pu Per Unit TUC Time Undercurrent
PUIB Pickup Current Block TUV Time Undervoltage
PUIT Pickup Current Trip TX (Tx) Transmit, Transmitter
PUSHBTN Pushbutton
PUTT Permissive Under-reaching Transfer Trip U Under
PWM Pulse Width Modulated UC Undercurrent
PWR Power UCA Utility Communications Architecture
UDP User Datagram Protocol
QUAD Quadrilateral UL Underwriters Laboratories
UNBAL Unbalance
R Rate, Reverse UR Universal Relay
RA Registration Authority URC Universal Recloser Control
RCA Reach Characteristic Angle .URS Filename extension for settings files
REF Reference UV Undervoltage
REM Remote
REV Reverse V/Hz Volts per hertz
R-GOOSE Routable GOOSE V_0 Zero Sequence voltage
RI Reclose Initiate V_1 Positive Sequence voltage
RIP Reclose In Progress V_2 Negative Sequence voltage
RGT BLD Right Blinder VA Phase A voltage
RMA Return Materials Authorization VAB Phase A to B voltage
RMS Root Mean Square VAG Phase A to Ground voltage
ROCOF Rate of Change of Frequency VARH Var-hour voltage
ROD Remote Open Detector VB Phase B voltage
RRTD Remote Resistance Temperature Detector VBA Phase B to A voltage
RST Reset VBG Phase B to Ground voltage
RSTR Restrained VC Phase C voltage
RTD Resistance Temperature Detector VCA Phase C to A voltage
RTU Remote Terminal Unit VCG Phase C to Ground voltage
RX (Rx) Receive, Receiver VF Variable Frequency
VIBR Vibration
s second VT Voltage Transformer
S Sensitive VTFF Voltage Transformer Fuse Failure
SAT CT Saturation VTLOS Voltage Transformer Loss Of Signal
SBO Select Before Operate
SCADA Supervisory Control and Data Acquisition WDG Winding
SCC Serial Communication Controller WH Watt-hour
SCD System Configuration Description w/ opt With Option
SCL Substation Configuration Language WGS World Geodetic System
SCEP Simple Certificate Enrollment Protocol WRT With Respect To
SEC Secondary
SEL Select / Selector / Selection X Reactance
SENS Sensitive XDUCER Transducer
SEQ Sequence XFMR Transformer
SFTP Secure Shell (SSH) File Transfer Protocol, Secure
File Transfer Protocol Z Impedance, Zone
SIR Source Impedance Ratio
SNTP Simple Network Time Protocol
SRC Source
SSB Single Side Band
SSEL Session Selector
STATS Statistics
SUPN Supervision
SUPV Supervise / Supervision
SV Supervision, Service
SYNC Synchrocheck
SYNCHCHK Synchrocheck
T Time, transformer
TC Thermal Capacity
TCP Transmission Control Protocol
TCU Thermal Capacity Used
TD MULT Time Dial Multiplier
TEMP Temperature
TFTP Trivial File Transfer Protocol
THD Total Harmonic Distortion
TMR Timer
TOC Time Overcurrent
TOV Time Overvoltage
TRANS Transient

ABBREVIATIONS

Index
Index
Alarms
Numerics acknowledge ....................................................................4-33, 6-2, 6-3
10BASE-F settings ...............................................................................5-41 add .............................................................................................. 4-34, 5-32
4L Discrepancy message .................................................................. 7-7 messages ................................................................................................7-5
7R module ................................................................................................3-39 overview ............................................................................................... 4-31
7S module ................................................................................................3-38 reset ...............................................................................................4-33, 6-3
AND gate explained ........................................................................... 4-81
Annunciator editor ............................................................................. 4-34
ANSI device numbers ...........................................................................2-2
A Application examples
AC current inputs .................................................................................3-18 breaker trip circuit integrity .......................................................5-187
specifications ......................................................................................2-19 contact inputs ..................................................................................5-194
AC voltage input specifications ...................................................2-19 direct inputs and outputs ...........................................................5-201
Accents ......................................................................................................4-55 latching outputs ..............................................................................5-197
Access Violation message ..............................................................3-66 Apply settings to other device ..................................................... 10-7
Acknowledge alarm ............................................................................. 6-3 Approvals ................................................................................................. 2-28
Activate relay .........................................................................................3-51 Architecture, relay ............................................................................5-141
Active setting group ........................................................................5-156 Audit list of port numbers ............................................................... 5-41
Actual values ............................................................................................ 6-1 Authentication by device or server ........................................... 5-13
alarms for graphical front panel ................................................. 6-2 Automatic discovery of UR devices .......................................... 3-65
display on graphical front panel ...................................4-34, 4-35 AWG wire size ........................................................................................ 3-45
monitor with Modbus Analyzer ..................................................10-1 F485 converter .................................................................................. 3-53
not activated graphical front panel .........................................4-52 G.703 interface .................................................................................. 3-38
Add Device from File option module 7S ............................................................................................ 3-38
restore settings to online device ............................................10-11 modules 6X, 6W ................................................................................ 3-20
save to Offline Window ..................................................................3-70 modules 7E, 7F, 7G, 7Q, 75 .......................................................... 3-45
Add Device to Offline Window preferences .........................10-9 modules 7L, 7M, 7N, 7P, 74 .......................................................... 3-44
Add module, check settings not defaulted ........................10-24 modules 7T, 7W ................................................................................ 3-42
Add relay ...................................................................................................3-55 RS422 and fiber interface ............................................................ 3-44
Administrator
add user account ..............................................................................5-11
command to force logoff ................................................................ 7-4
no automatic logout from front panel ....................................5-18
B
role for CyberSentry .......................................................................... 2-5 B90 function ..............................................................................................5-5
Alarm LEDs ...........................................................................................5-112 Back up settings ...................................................................... 5-55, 10-8
Bad IRIG-B Signal message ..............................................................7-7
Bad PTP Signal message ...................................................................7-8
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL i

INDEX
Basic front panel Cleaning .................................................................................................... 2-28

dimensions ............................................................................................. 3-2 Clear
FlexLogic ............................................................................................5-144 files and records ............................................................................ 10-29
interface ............................................................................................... 4-15 LEDs ..................................................................................................... 5-199
IP rating ................................................................................................ 2-26 relay records using IEC 61850 ................................................... 5-88
keypad .................................................................................................. 4-37 relay records using settings ........................................................ 5-36
labels ...................................................................................................... 4-47 security logs ...........................................................................................7-4
LEDs ..........................................................................................4-39, 5-112 Clock
navigation ........................................................................................... 4-49 actual values .........................................................................................6-7
order codes ............................................................................................ 2-8 graphical front panel format ...................................................... 5-26
pushbuttons .....................................................................................5-115 IRIG-B ..................................................................................................... 3-33
specifications ..................................................................................... 2-18 PTP ........................................................................................................ 5-102
use, change setting ......................................................................... 4-51 set ...............................................................................................................7-2
Battery settings ............................................................................................... 5-100
disposal ..............................................................................................10-26 synchronize several devices .................................................... 5-101
replace ................................................................................................10-25 Close
Baud rate ................................................................................................. 5-38 HTTP port .............................................................................................. 5-92
Blinking alarm ....................................................................................... 4-33 IEC 60870-5-104 port ..................................................................... 5-94
Block setting ............................................................................................. 5-4 Modbus port ....................................................................................... 5-47
Breaker failure TFTP port .............................................................................................. 5-93
configuration example ................................................................5-168 Web access port ............................................................................... 5-92
FlexLogic operands .......................................................................5-144 COMM Path Incomplete message ...................................... 7-7, 7-9
logic diagram ...................................................................................5-167 Comm status remaining connections ........................................6-8
settings ...............................................................................................5-162 Command line interface to software ..........................................C-1
specifications ..................................................................................... 2-17 Command password ...................................................... 4-57, 5-7, 5-8
Brightness ............................................................................................... 5-23 Commands
Bus differential ...................................................................................5-139 control user accounts .................................................................... 5-11
actual values ...................................................................................... 6-11 menu .........................................................................................................7-1
characteristic ...................................................................................5-158 with IEC 61850 ................................................................................... 5-88
FlexAnalogs ................................................................................. A-1, A-2 Communications
FlexLogic operands .......................................................................5-144 10BASE-F .............................................................................................. 5-41
logic diagram ...................................................................................5-161 connecting to the UR .......................................................... 3-63, 3-66
settings ...............................................................................................5-157 DNP ......................................................................................................... 5-48
specifications ..................................................................................... 2-16 HTTP ........................................................................................................ 5-92
Bus zone IEC 60870-5-10 ................................................................................. 5-95
actual values ...................................................................................... 6-11 IEC 60870-5-104 ............................................................................... 5-93
FlexAnalogs ................................................................................. A-1, A-2 inter-relay specifications .............................................................. 2-24
settings ...............................................................................................5-139 Modbus registers ........................................................................... 5-100
Modbus settings ............................................................................... 5-47
modem .................................................................................................. 3-64
C Protocol selection ............................................................................. 5-47
RS232 ......................................................................................... 3-30, 5-38
C37.94 communications ..................................................... 3-46, 3-49
RS485 ......................................................................................... 3-32, 5-38
Cannot log in ............................................................................................ 2-5
settings ...................................................................................... 5-41, 5-48
Caution symbol in Offline Window ........................................... 4-67
specifications ......................................................................... 2-23, 2-24
CE certification ..................................................................................... 2-28 timeout .................................................................................................. 5-47
Certification ............................................................................................ 2-28 web server ........................................................................................... 5-92
Changes ......................................................................................................D-1 Compare settings ................................................................................ 10-7
Check Settings message ................................................................... 7-6 Compliance ............................................................................................. 2-28
Chinese limited to 10 character input .................................... 5-24 COMTRADE files, view ....................................................................... 4-78
CID file, SCD file ............................................................ 5-73, 5-74, 5-75 Conducted RFI specifications ....................................................... 2-27
CID files Connect, unable to ................................................................. 3-66, 5-41
create .................................................................................................... 5-55 Connection timeout ........................................................................... 5-47
explained ............................................................................................. 3-70
Connectors, LC and ST ........................................................................3-9
import ......................................................................................3-70, 10-12
import preferences ......................................................................... 10-9
view ........................................................................................................ 5-56
Circuit monitoring applications ................................................5-185
ii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

INDEX
Contact inputs CyberSentry

actual values ......................................................................................... 6-4 FlexLogic operands .......................................................................5-144
explained ...........................................................................................5-193 installation ............................................................................... 3-69, 5-21
FlexLogic operands .......................................................................5-145 RS485 port limitation ...................................................................... 5-14
settings ...............................................................................................5-192 security commands ...........................................................................7-4
specifications ......................................................................................2-20 security overview ................................................................................2-5
thresholds .........................................................................................5-192 software options .............................................................................. 2-25
wet and dry connections ..............................................................3-25 specifications ..................................................................................... 2-25
Contact outputs system logs ......................................................................................... 5-22
actual values ......................................................................................... 6-5
explained ...........................................................................................5-195
FlexLogic operands .......................................................................5-145 D
settings ...............................................................................................5-195
D400 connection ................................................................................. 3-71
Control elements ...............................................................................5-180
Dark graphical front panel ............................................................ 5-28
Control power
Data, reading values ............................................................................6-1
description ...........................................................................................3-16
Dataset member is empty message ....................................... 5-65
specifications ......................................................................................2-23
Date
Control pushbuttons
firmware ............................................................................................... 6-16
FlexLogic operands .......................................................................5-144
last cleared fault report date ...................................................... 6-12
logic diagram ...................................................................................5-115
last cleared oscillography date ................................................. 6-14
settings ...............................................................................................5-114
last fault report date ....................................................................... 6-12
specifications ......................................................................................2-18
last settings change ....................................................................... 6-15
Convert device settings ....................................................................10-5
manufacturing date ........................................................................ 6-15
Copy of Copy of ....................................................................................10-7 set .................................................................................... 5-25, 5-100, 7-2
Copy settings for upgrading ..........................................................10-5 Decommission ....................................................................................10-29
Copy settings to other device .......................................................10-7 Default password ................................................................................ 5-11
CPU module diagram .......................................................................... 3-8 Default settings ........................................................................ 10-7, 10-8
CPU, new types T, U, V ....................................................................10-15 Default settings to factory default ...............................................7-3
CRC alarm .............................................................................................5-129 Definite time curve ...........................................................................5-176
Critical failure relay specifications .............................................2-22 Delete files and records .....................................................5-36, 10-29
CSA certification ...................................................................................2-28 Deploy settings ..................................................................................... 10-7
CT banks Device authentication ...................................................................... 5-13
settings ...............................................................................................5-131
Device Connectivity Report in Engineer ................................. 4-75
CT trouble
Device information files ..........................................................1-2, 4-75
Device overview ................................................................................... 10-1
logic diagram ...................................................................................5-189
Device setup .......................................................................................... 3-65
settings ...............................................................................................5-188
specifications ......................................................................................2-16
Diagnostic Alarm COP message ....................................................7-7
CT wiring ...................................................................................................3-18 Diagnostic Alarm DSP message ....................................................7-7
Current bank .......................................................................................5-131 Diagnostic Failure message ............................................................7-6
Current metering .................................................................................6-11 Diagnostics Failure message ..........................................................7-7
specifications ......................................................................................2-19 Dielectric strength .............................................................................. 3-16
Curves Differential
definite time .....................................................................................5-176 bus .................................................................2-16, 5-139, 5-157, 6-11
FlexCurves .........................................................................................5-132 Digital elements
IAC .........................................................................................................5-174 application example .....................................................................5-186
IEC .........................................................................................................5-173 FlexLogic operands .......................................................................5-144
IEEE .......................................................................................................5-172 logic diagram ...................................................................................5-185
types ....................................................................................................5-171 settings ...............................................................................................5-184
Cutout, panel ............................................................................................ 3-2 Digital outputs
see Contact outputs
Dimensions ................................................................................................3-2
Direct Device Off message ...............................................................7-7
Direct devices
settings ...............................................................................................5-200
status ........................................................................................................6-8

INDEX
Direct I/O EnerVista UR setup

application example .....................................................................5-201 command line interface ...................................................................C-1
configuration examples ..............................................................5-125 drag and drop files .............................................................................4-3
settings ...............................................................................................5-200 event recorder ......................................................................................4-2
Direct inputs firmware upgrade or downgrade .......................................... 10-14
actual values ......................................................................................... 6-7 installation ........................................................................................... 3-54
application example .....................................................................5-201 oscillography .........................................................................................4-2
clearing counters ................................................................................ 7-2 requirements ...................................................................................... 3-53
FlexLogic operands .......................................................................5-145 restart relay ...........................................................................................5-1
settings ...............................................................................................5-200 Engineer
specifications ..................................................................................... 2-20 command to force user logoff ......................................................7-4
Direct outputs create logic diagram ...................................................................... 4-59
application example .....................................................................5-201 Error messages ................................................................................. 4-68
clearing counters ................................................................................ 7-2 toolbar ................................................................................................... 4-79
settings ...............................................................................................5-200 Warning messages ......................................................................... 4-69
specifications ..................................................................................... 2-23 Enhanced front panel
Direct Ring Break message .............................................................. 7-8 FlexLogic ............................................................................................ 5-144
Discover button ................................................................................... 3-65 interface ............................................................................................... 4-15
Disk space required ........................................................................... 3-53 IP rating ................................................................................................. 2-26
Display settings .................................................................................... 5-23 keypad ................................................................................................... 4-37
Disposal ..................................................................................................10-31 labels ...................................................................................................... 4-42
Dispose of battery ............................................................................10-26 LEDs ......................................................................................... 4-38, 5-112
DNP navigation ............................................................................................ 4-49
connections remaining .................................................................... 6-8 order codes ............................................................................................2-8
select protocol ................................................................................... 5-47 pushbuttons .................................................................................... 5-115
settings ................................................................................................. 5-48 Rev. 1 and 2 explained ......................................................................3-2
view Points List in web browser ................................................ 5-51 specifications ..................................................................................... 2-18
DOS Partition Alarm message ........................................................ 7-7 use, change setting ......................................................................... 4-51
Downgrade Environment backup ......................................................................... 10-9
firmware .............................................................................................10-14 Equations
software .............................................................................................10-13 definite time curve ........................................................................ 5-176
Download FlexLogic ............................................................................................ 5-155
files from relay ................................................................................... 10-3 FlexLogic, protect ................................................................................4-9
settings to relay ................................................................................ 10-7 IAC curves ......................................................................................... 5-174
Drag and drop files ............................................................................... 4-3 IEC curves ......................................................................................... 5-173
IEEE curves ....................................................................................... 5-172
Duplicate
device settings .................................................................................. 10-7
Equipment Mismatch message .....................................................7-6
settings for upgrading ................................................................... 10-5 Error messages .......................................................................................7-5
Dynamic bus replica device not recognized ................................................................. 10-13
in Engineer ........................................................................................... 4-68
example ..............................................................................................5-141
see Isolator monitoring Ethernet
actual values .........................................................................................6-6
configuration ...................................................................................... 3-63
port failure monitoring .................................................................. 5-34
E port settings ........................................................................................ 5-41
Edition 1 and 2 IEC 61850 .............................................................. 5-53 port, turn on or off ........................................................................... 5-41
Electrostatic discharge specifications .................................... 2-27 ports on rear panel .............................................................................3-8
Elements ..................................................................................................... 5-3 Quick Connect ................................................................................... 3-68
End fault protection Event cause indicators ..................................................................... 4-38
FlexLogic operands .......................................................................5-144 Event Cause LEDs ................................................................................ 4-40
logic diagram ...................................................................................5-180 Event recorder
settings ...............................................................................................5-178 actual values ...................................................................................... 6-13
specifications ..................................................................................... 2-17 clearing ........................................................................................5-37, 7-2
End of life ...............................................................................................10-31 records explained ...............................................................................4-2
specifications ..................................................................................... 2-19
system logs ......................................................................................... 5-22
via EnerVista software ......................................................................4-2
view event records .......................................................................... 6-13

INDEX
Events setting .......................................................................................... 5-4 FlexLogic

Export settings to file .........................................................................10-8 create logic diagram with Engineer ........................................ 4-59
edit with equation editor ............................................................5-155
equation editor ................................................................................5-155
F error message ......................................................................................7-6
evaluation ..........................................................................................5-149
F485 .............................................................................................................3-53
example ..............................................................................................5-150
Factory default reset ......................................................5-5, 5-19, 7-3 gate characteristics ......................................................................5-148
Far-End Fault Indication ..................................................................5-42 lock equations ......................................................................................4-9
Fast form-C relay specifications .................................................2-22 lock equations to serial number ............................................... 4-11
Fast transient testing specifications ........................................2-27 operands ............................................................................................5-143
Features ...................................................................................................... 2-1 operators ...........................................................................................5-148
Fiber signal loss detection ..............................................................5-42 rules ......................................................................................................5-149
File transfer by IEC 61850 ...............................................................5-92 security ....................................................................................................4-9
File transfer by TFTP ...........................................................................5-93 specifications ..................................................................................... 2-17
Files status in single-line diagram of graphical front panel ... 4-31
delete ...................................................................................................10-29 timer settings ...................................................................................5-155
download from relay .......................................................................10-3 worksheet ..........................................................................................5-152
drag and drop ...................................................................................... 4-3 Force contact inputs .......................................................................5-205
protect FlexLogic with password ................................................ 4-9 Force contact outputs ....................................................................5-206
protect with password ..................................................................... 4-7 Foreign language
transfer from relay ...........................................................................4-16 keyboard .............................................................................................. 4-55
transfer to relay ....................................................................... 4-1, 4-16 setting .................................................................................................... 5-23
Firmware not supported by EnerVista .................................10-14 Form-A relay
Firmware revision ................................................................................6-16 actual values .........................................................................................6-5
Firmware upgrade or downgrade ..........................................10-14 high-impedance circuits ............................................................... 3-20
Firmware version does not match EnerVista ...................10-13 outputs .................................................................................................. 3-18
First Ethernet Fail specifications ..................................................................................... 2-22
error message ...................................................................................... 7-8 Form-C
set alarm ...............................................................................................5-34 actual values .........................................................................................6-5
Flash memory .....................................................................................10-29 critical failure relay .......................................................................... 3-16
Flash memory data storage ..........................................................3-17 order codes ............................................................................................2-8
Flash messages ....................................................................................5-23 outputs .................................................................................................. 3-18
Flex State parameters replacement modules .................................................................... 2-12
actual values ......................................................................................... 6-6 specifications ..................................................................................... 2-22
settings ...............................................................................................5-121 FPGA
specifications ......................................................................................2-18 revision .................................................................................................. 6-16
FlexAnalog parameters ...................................................................... A-1 upgrade ..............................................................................................10-15
FlexCurves Frequency
settings ...............................................................................................5-132 actual values ...................................................................................... 6-12
specifications ......................................................................................2-17 metering and tracking .................................................................5-131
table .....................................................................................................5-132 nominal ...............................................................................................5-131
tracking ...............................................................................................5-131
Frequency metering
specifications ..................................................................................... 2-19
Frequency specifications ................................................................ 2-19
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL v

INDEX
Front panel ................................................................................................ 3-2 Graphical front panel ..................................................................... 10-15

clear .....................................................................................................5-199 actual value menu not activated ............................................. 4-52
custom labels .................................................................................... 4-42 actual values, phasors ................................................................... 4-56
dimensions ............................................................................................. 3-2 alarm acknowledge, reset ........................................ 4-33, 6-2, 6-3
install ...................................................................................................10-15 alarm setup ......................................................................................... 5-32
interface ............................................................................................... 4-15 annunciator editor ........................................................................... 4-34
keypad .................................................................................................. 4-37 date and time ..................................................................................... 5-26
labels ...................................................................................................... 4-42 explained .............................................................................................. 4-17
language .............................................................................................. 5-23 FlexLogic ............................................................................................ 5-143
LEDs ........................................................................................................ 4-38 Home page configuration ............................................................ 5-25
number of characters .................................................................... 4-17 interface ............................................................................................... 4-16
password change ............................................................................ 4-57 IP rating ................................................................................................. 2-26
plastic protective film ..................................................................10-20 labels ...................................................................................................... 4-48
pushbuttons .....................................................................................5-115 LEDs ......................................................................................... 4-41, 5-112
specifications ..................................................................................... 2-25 Metering Editor .................................................................................. 4-35
switch between enhanced and basic .................................... 3-54 navigation ............................................................................................ 4-50
trouble message ................................................................................. 7-8 navigation keys ................................................................................. 4-37
types ...................................................................................................... 4-15 no display ............................................................................................. 5-28
use .......................................................................................................... 4-15 order codes ............................................................................................2-8
use in EnerVista ....................................................................... 4-17, 6-2 phasor diagram .................................................................... 4-56, 5-29
Function setting ...................................................................................... 5-4 plastic protective film .................................................................. 10-20
Fuse specifications ............................................................................ 2-21 pushbutton testing .............................................................................7-3
Fuses not field-replaceable ........................................................10-30 pushbuttons .................................................................................... 5-115
pushbuttons 9 to 16 ........................................................................ 4-29
settings .................................................................................................. 5-25
single-line diagrams ....................................................................... 4-19
G specifications ......................................................................... 2-23, 2-25
G.703 .......................................................................................................... 3-38 time ......................................................................................................... 5-26
wire size ................................................................................................ 3-38 USB port ............................................................................................. 5-100
Gates, logic explained ...................................................................... 4-81 use, change setting ......................................................................... 4-52
Gateway address ................................................................................ 5-44 view LEDs and pushbuttons in software ..................................6-3
GE type IAC curves ...........................................................................5-174 Group 1 switch after powerup ................................................. 5-157
Getting help ............................................................................................... 1-2 Grouped elements ........................................................................... 5-156
GFP Version Mismatch message .................................................. 7-8 Guarantee ................................................................................................. D-1
GGIO Ind Oscill message ................................................................... 7-8
GOOSE
actual values ...................................................................................... 6-12
FlexAnalogs ...........................................................................................A-3
H
routable, explained ......................................................................... 5-63 Heartbeat messages ............................................................. 5-64, 5-67
settings ................................................................................................. 5-63 Help, getting ..............................................................................................1-2
simulation operands ....................................................................5-148 Home page configuration .............................................................. 5-25
simulation settings ........................................................................5-207 HTTP ............................................................................................................ 5-92
port, close ............................................................................................ 5-92
Humidity specifications ................................................................... 2-26
I
IAC curves ............................................................................................. 5-174
ICD file ................................................................................ 5-73, 5-74, 5-75
IEC 60870-5-103 protocol
explained .............................................................................................. 5-95
select protocol ................................................................................... 5-47
settings .................................................................................................. 5-95
IEC 60870-5-104 protocol
connections remaining .....................................................................6-8
port, close ............................................................................................ 5-94
select protocol ................................................................................... 5-47
settings .................................................................................................. 5-93
vi B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

INDEX
IEC 61850 protocol IRIG-B

Edition 1 and 2 support ..................................................................5-53 connection on rear panel ................................................................3-8
explained ..............................................................................................5-53 explained .............................................................................................. 3-33
file transfer ...........................................................................................5-92 port on rear panel ...............................................................................3-8
heartbeat messages ...........................................................5-64, 5-67 specifications ..................................................................................... 2-20
IID file ......................................................................................................10-8 ISO standards ........................................................................................ 2-28
settings in EnerVista ........................................................................5-52 Isolator monitoring
specifications ......................................................................................2-23 FlexLogic operands .......................................................................5-145
IEC CID files ..............................................................................................5-55 settings ...............................................................................................5-189
IED setup ...................................................................................................3-54 specifications ..................................................................................... 2-16
IEEE C37.94 communications ...........................................3-46, 3-49
IEEE curves ...........................................................................................5-172
IID file ..................................................................................3-70, 5-56, 10-8 J
import preferences ..........................................................................10-9 Japanese limited to 10 character input ................................. 5-24
Import settings file ..............................................................................3-70
Import settings from SCD or CID file ......................................10-12
In service indicator ............................................................................... 7-5
In Service LED ........................................................................................3-51
K
Incompatible device order codes or versions ..................10-14 Keyboard .................................................................................................. 4-55
Inputs Keypad ...................................................................................................... 4-37
AC current specifications ..............................................................2-19
AC voltage specifications ..............................................................2-19
contact input specifications ........................................................2-20 L
contact inputs .................................................................. 5-192, 5-205 Labels, front panel .................................................................. 4-42, 4-74
direct input specifications ............................................................2-20 Lamp test ....................................................................................................7-3
IRIG-B ......................................................................................................3-33 Language setting ................................................................................ 5-23
IRIG-B specifications .......................................................................2-20 Laser module ......................................................................................... 3-37
virtual ..................................................................................................5-194 Latching outputs
Installation ................................................................................................. 3-2 application examples ...................................................................5-197
activate relay ......................................................................................3-51 settings ...............................................................................................5-196
add UR devices with auto discovery .......................................3-65 specifications ..................................................................................... 2-21
communications ...............................................................................3-31 LC fiber ................................................................................................2-8, 3-8
CT inputs ...............................................................................................3-18 LC fiber connector .................................................................................3-9
front panel ........................................................................................10-15 LED test
RS485 .....................................................................................................3-32 commands .............................................................................................7-3
set relay to Programmed ..............................................................3-51 FlexLogic operand .........................................................................5-146
settings ...............................................................................................5-130 settings ...............................................................................................5-109
Instantaneous overcurrent specifications ..................................................................................... 2-18
settings ...............................................................................................5-176 LEDs
Interface clear ......................................................................................................5-199
front panel ...........................................................................................4-15 custom labels ..................................................................................... 4-42
software .................................................................................................. 4-1 explained .............................................................................................. 4-38
Internet access .....................................................................................5-92 In Service .............................................................................................. 3-51
Inter-relay communication specifications ............................2-24 power supply module .................................................................... 3-17
IOC settings ...............................................................................................5-112
FlexLogic operands .......................................................................5-145 Trouble .................................................................................................. 3-51
settings ...............................................................................................5-176 view in software for graphical front panel ..............................6-3
specifications ......................................................................................2-16 Link power budget .............................................................................. 2-24
IP address Local access denied message ......................................... 4-58, 5-18
enter in software ...............................................................................5-41 Local access, explained ......................................................................5-6
enter on front panel ............................................................3-56, 4-37 Local Setting Authorization .........................................................10-14
gateway ................................................................................................5-44 Lockout from software .................................................................... 5-11
rules .........................................................................................................3-56
Log in with password ......................................................3-69, 5-7, 5-8
view .........................................................................................................5-41
Log in, multiple users cannot ..........................................................2-5
IP address migration ..........................................................................3-70
Log out
IP rating .....................................................................................................2-26
Administrator manually from front panel ............................ 5-18
IP54 for enhanced front panel ..................................................... 3-2
users forcefully .....................................................................................7-3
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL vii

INDEX
Logic diagram Module 7S ................................................................................................ 3-38

create .................................................................................................... 4-59 Modules
explained ............................................................................................. 4-58 add and check settings not defaulted ................................ 10-24
Logic gates, FlexLogic ........................................................4-81, 5-149 communications ............................................................................... 3-31
Logs, system .......................................................................................... 5-22 CT and VT ............................................................................................. 3-18
Lost password ......................................................................................... 5-5 order codes ......................................................................................... 2-12
Low on Memory message ................................................................ 7-7 power supply ...................................................................................... 3-16
replace ............................................................................................... 10-23
Monitor
actual values ...................................................................................... 10-1
M actual values with Metering Editor .......................................... 5-28
MAC address devices .................................................................................................. 10-1
actual values ...................................................................................... 6-15
use alarms ........................................................................................... 5-32
examples ............................................................................................. 5-39
Monitoring elements settings ................................................... 5-187
RxGOOSE .............................................................................................. 5-70
Mounting .....................................................................................................3-2
settings for redundancy ............................................................... 5-42
TxGOOSE .............................................................................................. 5-66
Maintenance
alert error message ........................................................................... 7-7 N
battery replacement ....................................................................10-25 Nameplate, rear ......................................................................................3-1
cleaning ................................................................................................ 2-28 NAND gate explained ....................................................................... 4-81
commands ............................................................................................. 7-3 Navigation keys .................................................................................... 4-37
module replacement ....................................................................10-23 Network settings migration .......................................................... 3-70
upgrade or downgrade ...............................................................10-14 No connection ....................................................................................... 5-41
Manufacturing date .......................................................................... 6-15 Non-volatile data storage .............................................................. 3-17
Maximum 6X, 6X wire size ............................................................. 3-20 Non-volatile latches
Measurements of UR and panel cutout .................................... 3-2 FlexLogic operands ...................................................................... 5-145
Media storage alarm message ................................................... 7-10 settings ............................................................................................... 5-155
Memory low message ......................................................................... 7-7 specifications ..................................................................................... 2-18
Memory requirements ..................................................................... 3-53 NOR gate explained ........................................................................... 4-81
Menu navigation ................................................................................. 4-49 NOT gate explained ........................................................................... 4-81
Message about upgrade over Internet ................................10-14
Messages
clear front panel .............................................................................5-199 O
error .......................................................................................................... 7-5 Obtain list of port numbers ........................................................... 5-41
errors and warnings in Engineer .............................................. 4-67
One-shot
Metering error compiling in Engineer ......................................................... 4-68
conventions ........................................................................................ 6-10
FlexLogic operators ...................................................................... 5-149
current specifications .................................................................... 2-19
Operating system
editor in graphical front panel ................................................... 4-35
language .............................................................................................. 3-54
frequency specifications .............................................................. 2-19
requirements ...................................................................................... 3-53
Microsoft Windows requirement ............................................... 3-53
Operating temperature ................................................................... 2-26
Mimic diagrams ................................................................................... 4-19
Operating times ................................................................................... 2-16
Missing messages, RxGOOSE fail .................................................. 7-9
Operator command to force logoff .............................................7-4
MMS connections remaining .......................................................... 6-8
OR gate explained .............................................................................. 4-81
Modbus
Order codes ...............................................................................................2-8
connections remaining .................................................................... 6-8
update ..........................................................................................3-64, 7-3
Flex State parameters .................................................................5-121
view as actual values ..................................................................... 6-15
Modbus Analyzer window ............................................................ 10-1
Oscillatory GOOSE maintenance message .............................7-8
port, close ............................................................................................ 5-47
Oscillatory transient testing specifications .......................... 2-27
register entry ....................................................................................5-100
settings ................................................................................................. 5-47
user map ............................................................................................5-100
Model information, view ................................................................. 6-15
Model number ......................................................................................... 3-1
Modem connection ............................................................................ 3-64
Modification file number ................................................................. 6-16
Module 7R ............................................................................................... 3-39
viii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

INDEX
Oscillography Ping test times out .............................................................................. 5-41

actual values .......................................................................................6-14 Plastic film on front panel ............................................................10-20
clearing ........................................................................................ 5-37, 7-2 Points List, view DNP ......................................................................... 5-51
how to .................................................................................................5-107 Port
settings ...............................................................................................5-106 Ethernet, turn on or off .................................................................. 5-41
specifications ......................................................................................2-18 failure monitoring ............................................................................ 5-34
via EnerVista software ..................................................................... 4-2 HTTP, close .......................................................................................... 5-92
view waveform in actual values window ..............................6-14 IEC 60870-5-104, close ................................................................. 5-94
view waveform in event record .................................................6-13 Modbus, close .................................................................................... 5-47
Out of service ........................................................................................... 5-1 on rear panel .........................................................................................3-8
Outputs TFTP, close ........................................................................................... 5-93
contact outputs ..............................................................................5-195 USB ......................................................................................................... 4-16
control power specifications .......................................................2-23 Port number
critical failure relay specifications ............................................2-22 combinations with protocols ...................................................... 5-47
Fast form-C relay specifications ................................................2-22 connectivity report of those used ............................................ 4-75
Form-A relay ...........................................................................2-21, 3-18 DNP ......................................................................................................... 5-48
Form-C relay .......................................................................................3-18 HTTP ....................................................................................................... 5-92
Form-C relay specifications .........................................................2-22 IEC 60870-5-104 ............................................................................... 5-93
latching output specifications ....................................................2-21 list of ....................................................................................................... 5-41
latching outputs .............................................................................5-196 Modbus ................................................................................................. 5-47
virtual outputs .................................................................................5-199 Modbus during installation .......................................................... 3-64
Over Temperature message .........................................................7-10 RADIUS .................................................................................................. 5-16
Overcurrent curves SNTP .....................................................................................................5-104
IAC .........................................................................................................5-174 system log ............................................................................... 5-16, 5-17
IEC .........................................................................................................5-173 TFTP ........................................................................................................ 5-93
types ....................................................................................................5-171 Power off, save data first ................................................................ 3-17
Power supply
description ........................................................................................... 3-16
P diagram ...................................................................................................3-8
Panel cutout .............................................................................................. 3-2 LED on module .................................................................................. 3-17
removal to replace battery ........................................................10-25
Parallel Redundancy Protocol
RH/RL vs SH/SL ................................................................................10-25
actual values ......................................................................................... 6-9
specifications ..................................................................................... 2-21
explained ..............................................................................................5-43
wire size ................................................................................................ 3-17
settings ..................................................................................................5-41
specifications ......................................................................................2-24
Power System
settings ...............................................................................................5-131
Parity ...........................................................................................................5-38
Precision Time Protocol
Part numbering ....................................................................................... 2-8
actual values for port state ............................................................6-7
Passwords
clock settings ...................................................................................5-100
authentication by device or server ..........................................5-13
port behavior ...................................................................................... 5-42
bypass authentication ...................................................................5-20
settings ...............................................................................................5-102
change ...................................................................................................4-57
specifications ..................................................................................... 2-24
change after installation ...............................................................3-69
Preferences
change does not take relay out of service ............................. 5-1
comparing settings ......................................................................... 10-7
command ..........................................................................4-57, 5-7, 5-8
Engineer ............................................................................................... 4-75
default ....................................................................................................5-11
IEC 61850 ............................................................................................. 5-58
explained ................................................................................................ 2-4
import file ............................................................................................. 10-9
lockout .......................................................................................4-58, 5-11
Preserve custom attributes importing SCD/CID files ..... 10-9
lost password ....................................................................................... 5-5 Press Reset Key message .............................................................. 7-10
requirements ........................................................................................ 5-6 Print front panel labels ......................................................... 4-42, 4-74
reset to factory defaults .................................................................. 5-5 Product information
rules ........................................................................................................... 5-6 actual values ...................................................................................... 6-15
settings ...............................................................................4-57, 5-7, 5-8 Device Connectivity Report in Engineer ................................ 4-75
settings templates .............................................................................. 4-7 firmware revision ............................................................................. 6-16
wrong entry .........................................................................................4-58 Product setup ...........................................................................................5-5
Per-unit quantity .................................................................................... 5-4 Programmed mode ........................................................................... 3-51
Phase angle metering .......................................................................6-10 Protection elements .............................................................................5-3
Phasor display graphical front panel ...........................4-56, 5-29 Protection Summary interface ............................ 3-67, 4-4, 5-181
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL ix

INDEX
Protocol selection ............................................................................... 5-47 Remote access, explained ................................................................5-6

Prototype Firmware message ........................................................ 7-9 Remote Setting Authorization ................................................... 10-14
PRP Repair ................................................................................... 1-2, 10-30, D-1
actual values ......................................................................................... 6-9 Replace battery ................................................................................. 10-25
explained ............................................................................................. 5-43 Replace Battery message .................................................................7-8
settings ................................................................................................. 5-41 Replace front panel ......................................................................... 10-15
specifications ..................................................................................... 2-24 Replacement modules ...................................................... 2-12, 10-23
PTP Requirements for installation ....................................................... 3-53
actual values for port state ............................................................ 6-7 Reset alarm ................................................................................................6-3
clock settings ...................................................................................5-100 Reset to factory defaults ........................................................5-5, 5-19
port behavior ..................................................................................... 5-42 Resetting
settings ...............................................................................................5-102 FlexLogic operands ...................................................................... 5-147
specifications ..................................................................................... 2-24 setting to clear LEDs and messages .................................... 5-199
pu quantity ................................................................................................ 5-4 to factory defaults .................................................................... 5-5, 7-3
Pushbuttons Restart relay
control FlexLogic ............................................................................5-144 using EnerVista .....................................................................................5-1
control logic diagram ...................................................................5-115 using relay ..............................................................................................7-3
control settings ...............................................................................5-114 Restore settings ................................................................................... 10-8
control specifications ..................................................................... 2-18 Revision history ...................................................................................... D-1
testing ...................................................................................................... 7-3 RF immunity specifications ........................................................... 2-27
user-programmable FlexLogic ................................................5-148
RFI, conducted specifications ...................................................... 2-27
user-programmable logic diagrams ....................................5-120
R-GOOSE description ........................................................................ 5-63
user-programmable settings ...................................................5-115
RH/RL power supply module ..................................................... 10-25
user-programmable specifications ......................................... 2-18
view in software for graphical front panel ............................. 6-3
RJ-45 ................................................................................................... 2-8, 3-8
Roles for login ...........................................................................................2-5
Routable GOOSE .................................................................................. 5-63
RS232
Q baud rate ............................................................................................. 5-38
Quick Connect .......................................................................... 3-67, 3-68 configuration ...................................................................................... 3-67
specifications ..................................................................................... 2-23
wiring ..................................................................................................... 3-30
R RS422
RADIUS server configuration ...................................................................................... 3-42
authentication ................................................................................... 5-13 timing ..................................................................................................... 3-43
explained .......................................................................................2-5, 2-7 two-channel application ............................................................... 3-42
setup .........................................................................................................B-1 with fiber interface .......................................................................... 3-44
RAM Filesystem Fail message ........................................................ 7-6 RS485
RAM required ......................................................................................... 3-53 description ........................................................................................... 3-32
Real-time clock limitation with CyberSentry ......................................................... 5-14
actual values for synchronization ............................................... 6-7 port on rear panel ...............................................................................3-8
settings ...............................................................................................5-100 settings .................................................................................................. 5-38
Reboot relay specifications ..................................................................................... 2-23
using EnerVista .................................................................................... 5-1 Rules for passwords .............................................................................5-6
using relay .............................................................................................. 7-3 RxGOOSE
Recloser curves ..................................................................................5-135 actual values ...................................................................................... 6-12
Redundancy FlexAnalogs ............................................................................................A-3
power supply ...................................................................................10-25 settings .................................................................................................. 5-68
PRP actual values ............................................................................... 6-9 RxGOOSE Fail message ......................................................................7-9
PRP explained .................................................................................... 5-43 RxGOOSE Offline message ................................................................7-9
settings ................................................................................................. 5-41
SNTP .....................................................................................................5-104
specifications ..................................................................................... 2-24 S
Relay architecture ............................................................................5-141 Save settings .............................................................................................4-1
Relay maintenance ............................................................................... 7-3 Saving setting does not take relay out of service ...............5-1
Relay name ...........................................................................................5-130 SCADA protocol selection ............................................................... 5-47
Release Notes .....................................................................................10-14
Remote access of front panel in EnerVista ................. 4-17, 6-2
x B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

INDEX
SCD file Settings ........................................................................................................5-1

import ..................................................................................................10-12 back up ..................................................................................... 5-55, 10-8
import preferences ..........................................................................10-9 change .................................................................................................. 4-51
SCL compatible .....................................................................................5-53 change does not take relay out of service ..............................5-1
SCL file import ................................................................5-73, 5-74, 5-75 compare ............................................................................................... 10-7
Edition 1 versus 2 ..............................................................................5-53 control user accounts .................................................................... 5-11
preferences .........................................................................................10-9 convert .................................................................................................. 10-5
Second Ethernet Fail default to factory defaults ..............................................................7-3
error message ...................................................................................... 7-8 edit .......................................................................................................... 4-51
set alarm ...............................................................................................5-34 export .................................................................................................... 10-8
Security import .................................................................................................... 3-70
commands ............................................................................................. 7-4 lock .............................................................................................................4-5
delete files and records ..............................................................10-29 not updated automatically among computers ................. 3-66
EnerVista and UR secure with SSH ............................................. 2-5 read from device with Modbus Analyzer .............................. 10-1
failed authentication lockout ......................................................5-19 restore ................................................................................................... 10-8
forceful user logout ........................................................................... 7-3 upgrade ................................................................................................ 10-5
lock FlexLogic equations ................................................................. 4-9 write to device with Modbus Analyzer ................................... 10-1
lock settings .......................................................................................... 4-5 Settings file ............................................................................................. 5-55
password for settings template ................................................... 4-7 description ..............................................................................................4-1
passwords for settings and commands .............4-57, 5-7, 5-8 import .................................................................................................... 3-70
RADIUS server for user authentication ..................................... B-1 takes relay out of service when loaded ....................................4-2
role-based user access .................................................................... 2-5 traceability .......................................................................................... 4-12
settings ..................................................................................................5-17 transfer with USB stick .................................................................. 4-16
software options ...............................................................................2-25 Settings password ............................................................4-57, 5-7, 5-8
specifications ......................................................................................2-25 Settings Save Error message ..........................................................7-9
system and event logs ...................................................................5-22 Settings templates
Security audit list of port numbers ............................................5-41 description ..............................................................................................4-5
Self-tests edit .............................................................................................................4-6
description ............................................................................................. 7-5 enable .......................................................................................................4-5
error messages .................................................................................... 7-5 password protection .........................................................................4-7
FlexLogic operands .......................................................................5-147 remove .....................................................................................................4-9
user-programmable .....................................................................5-113 view ...........................................................................................................4-7
Serial number ................................................................... 3-1, 4-11, 6-15 SFP
Serial ports explained .................................................................................................3-7
device setup with ..............................................................................3-62 module fail message .........................................................................7-9
location ..................................................................................................4-15 photo ....................................................................................................10-21
settings ..................................................................................................5-38 SH/SL power supply module ......................................................10-25
specifications ......................................................................................2-23 Signal loss detection for fiber ...................................................... 5-42
wiring ......................................................................................................3-44 Simulation
Server authentication .......................................................................5-13 operands ............................................................................................5-148
Service life expected ..........................................................................10-3 settings ...............................................................................................5-207
Service Report ......................................................................................... 1-2 Simulation bit .......................................................................................5-204
Setting Changed message ............................................................... 7-8 Single-line diagram ...............................................................................2-3
Setting groups .......................................................5-156, 5-157, 5-183 create, explained .............................................................................. 4-19
active setting group .....................................................................5-156 save as separate file ....................................................................... 4-24
FlexLogic operands .......................................................................5-145 Site Targets ............................................................................................. 10-1
troubleshooting ..............................................................................5-157 Size of UR and panel cutout .............................................................3-2
SNTP Failure message .........................................................................7-9
SNTP protocol
accuracy specifications ................................................................ 2-24
redundant source ..........................................................................5-104
settings ...............................................................................................5-104
Software
installation ........................................................................................... 3-54
interface explained ............................................................................4-1
language .............................................................................................. 5-24
system requirements ..................................................................... 3-53
update or downgrade ..................................................................10-13
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL xi

INDEX
Special characters ............................................................................. 4-55 TFTP

Specifications ........................................................................................ 2-15 port, close ............................................................................................ 5-93
ST fiber ................................................................................................2-8, 3-8 put cannot be done ......................................................................... 5-93
ST fiber connector ................................................................................. 3-9 settings .................................................................................................. 5-93
Standards, certification ................................................................... 2-28 The URS file is part of a device folder ................................... 10-11
Status LEDs ................................................................................. 4-40, 4-41 Third Ethernet Fail
Stop blinking alarm ............................................................................ 4-33 error message ......................................................................................7-8
Storage Media Alarm message .................................................. 7-10 set alarm .............................................................................................. 5-34
Storage temperature ........................................................................ 2-26 Tilda on front panel ............................................................................ 4-17
Storage, UR ...........................................................................................10-30 Time
Substation D400 .................................................................................. 3-71 actual values .........................................................................................6-7
Support, technical ................................................................................. 1-2 FlexLogic timer settings ............................................................. 5-155
Surge immunity specifications .................................................... 2-27 graphical front panel format ...................................................... 5-26
Switch operating .............................................................................................. 6-15
IEC 61850 Edition 1 and 2 ............................................................ 5-53 overwritten by external source ....................................................7-2
set .................................................................................... 5-25, 5-100, 7-2
Synchronize
clock using time source ..............................................................5-100
Time overcurrent settings ........................................................... 5-177
clocks of UR devices to local computer ..............................5-101 Time overcurrent specifications ................................................. 2-16
files between offline and online ................................................ 4-67 Timeout, connection .......................................................................... 5-47
Synchronize Devices setting for clocks ...............................5-101 To Install Settings message .............................................................7-6
Syslog ......................................................................................................... 5-22 TOC
System and device information ................................................. 4-75 FlexLogic operands ...................................................................... 5-145
System Exception message .......................................................... 7-10 settings ............................................................................................... 5-177
System Failure message .................................................................... 7-6 specifications ..................................................................................... 2-16
System frequency .............................................................................5-131 Toolbar ...................................................................................................... 4-79
System logs ............................................................................................ 5-22 Torque for screws ..........................................................2-28, 3-8, 3-20
System requirements ....................................................................... 3-53 Traceability
data ........................................................................................................ 4-13
System Setup menu ........................................................................5-131
overview ............................................................................................... 4-12
rules ........................................................................................................ 4-14
view data .............................................................................................. 4-14
T Transfer files to relay ......................................................................... 10-7
Targets Transfer files with USB drive ......................................................... 4-16
defined .................................................................................................. 4-19 Triangle in Offline Window ............................................................. 4-67
menu ......................................................................................................... 7-4 Trip bus
messages ............................................................................................... 7-5 FlexLogic operands ...................................................................... 5-145
overview by device .......................................................................... 10-1 logic diagram .................................................................................. 5-183
settings .................................................................................................... 5-4 settings ............................................................................................... 5-181
TBD .............................................................................................................. 10-9 Trip LEDs ................................................................................................ 5-112
TCP port number for web access .............................................. 5-92 Trouble indicator ....................................................................................7-5
Technical support .................................................................................. 1-2 Trouble LED ............................................................................................. 3-51
files ................................................................................................. 1-2, 10-3 Troubleshooting
Temp Monitor message .................................................................. 7-10 access to device ............................................................................... 3-66
Temperature breaker not working .................................................................... 5-184
FlexLogic monitor operand .......................................................5-148 connection ........................................................................................... 5-41
operating and storage .................................................................. 2-26 dark graphical front panel ........................................................... 5-28
Test voltages ......................................................................................... 3-16 Engineer .................................................................................... 4-68, 4-69
Testing error messages ....................................................................................7-5
force contact inputs .....................................................................5-205 setting not working ...................................................................... 5-184
force contact outputs ..................................................................5-206 unit not programmed error ...................................................... 5-130
lamp test ................................................................................................. 7-3 Turn off alarm ....................................................................................... 4-33
LEDs ........................................................................................................... 7-3 TxGOOSE
pushbuttons .......................................................................................... 7-3 actual values .............................................................................6-9, 6-10
self-test error messages .................................................................. 7-5 settings .................................................................................................. 5-63
settings ................................................................................ 5-204, 5-205
xii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

INDEX
User-programmable LEDs
U custom labels ..................................................................................... 4-42
UDP for TFTP ...........................................................................................5-93 defaults ................................................................................................. 4-41
UL certification ......................................................................................2-28 settings ...............................................................................................5-112
Unable to connect to relay .................................................3-66, 5-41 specifications ..................................................................................... 2-18
Unable to put relay in flash mode ...........................................10-14 User-programmable pushbuttons
Unauthorized access FlexLogic operands .......................................................................5-148
commands ...........................................................................................5-37 graphical front panel buttons 9 to 16 .................................... 4-29
resetting .................................................................................................. 7-2 logic diagrams .................................................................................5-120
Undervoltage settings ...............................................................................................5-115
FlexLogic operands .......................................................................5-145 specifications ..................................................................................... 2-18
settings ...............................................................................................5-170 testing .......................................................................................................7-3
specifications ......................................................................................2-17 User-programmable self-test settings .................................5-113
Uninstall .................................................................................................10-29
Unit Not Calibrated message .......................................................7-10
Unit not programmed ...........................................................5-130, 7-6 V
Unpacking the relay ............................................................................. 3-1 Vibration testing specifications .................................................. 2-27
Unreturned messages alarm .....................................................5-130 Virtual inputs
Update SCL files prompt ..................................................................4-67 actual values .........................................................................................6-4
Update settings with Convert Device Settings ...................10-5 commands .............................................................................................7-2
Updates explained ............................................................................................5-194
device not recognized .................................................................10-13 FlexLogic operands .......................................................................5-146
firmware .............................................................................................10-14 logic diagram ...................................................................................5-195
FPGA .....................................................................................................10-15 settings ...............................................................................................5-194
instruction manual ............................................................................. 3-1 Virtual outputs
order code .............................................................................................. 7-3 actual values .........................................................................................6-5
single-line diagrams not retained .............................................4-24 explained ............................................................................................5-199
software .............................................................................................10-13 FlexLogic operands .......................................................................5-146
Upgrade device settings ..................................................................10-5 settings ...............................................................................................5-199
Upgrade over Internet message ..............................................10-14 Voltage deviation specifications ................................................ 2-27
Upload settings to relay ...................................................................10-7 Voltage metering ................................................................................. 6-12
URS file does not include IEC 61850 configuration .......10-11 Voltage Monitor message .............................................................. 7-10
URS file is part of a device folder .............................................10-11 VT wiring ................................................................................................... 3-18
URS settings file ............................................................3-70, 5-55, 10-8
USB port
graphical front panel .......................................................4-16, 5-100 W
Quick Connect ....................................................................................3-68 Warning messages in Engineer .................................................. 4-69
specifications ......................................................................................2-23 Warning symbol in Offline Window .......................................... 4-67
User accounts Warning, firmware upload not supported ..........................10-14
add ...........................................................................................................5-11 Warranty .................................................................................................... D-1
authentication by device or server ..........................................5-13 Waveform
multiple login limitation CyberSentry ........................................ 2-5 view in actual values window .................................................... 6-14
passwords for settings and commands .............4-57, 5-7, 5-8 view in event record ....................................................................... 6-13
permissions by role ............................................................................ 2-5
Waveform files, view ......................................................................... 4-78
permissions, set .................................................................................5-11
Web access port .................................................................................. 5-92
User-definable displays
Web server protocol .......................................................................... 5-92
example ..............................................................................................5-123
Windows requirement ..................................................................... 3-53
invoking and scrolling ..................................................................5-122
settings ...............................................................................................5-122
specifications ......................................................................................2-18
User-programmable fault report
actual values .......................................................................................6-12
clearing ........................................................................................ 5-36, 7-2
settings ...............................................................................................5-106
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL xiii

INDEX
Wire size
F485 converter .................................................................................. 3-53
G.703 and fiber interface ............................................................. 3-45
G.703 interface .................................................................................. 3-38
module 7S ........................................................................................... 3-38
modules 6X, 6W ................................................................................ 3-20
modules 7E, 7F, 7G, 7Q, 75 .......................................................... 3-45
modules 7L, 7M, 7N, 7P, 74 ......................................................... 3-44
modules 7T, 7W ................................................................................ 3-42
power supply module .................................................................... 3-17
RS422 and fiber interface ............................................................ 3-44
RS422 interface ................................................................................ 3-42
Wiring diagrams .................................................................................. 3-10
Withdraw UR from operation ....................................................10-29
Wrong Transceiver message ....................................................... 7-10
X
XOR gate explained ........................................................................... 4-81
Y
Yellow caution icon in Offline Window ................................... 4-67
xiv B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Low Impedance Bus Differential System: Grid Solutions

Uploaded by

Copyright:

Available Formats

Low Impedance Bus Differential System: Grid Solutions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Low Impedance Bus Differential System: Grid Solutions

Uploaded by

Copyright:

Available Formats

GE

1 INTRODUCTION 1.1 Safety symbols and definitions ........................................................................... 1-1

2 PRODUCT 2.1 Product description ............................................................................................... 2-1

3 INSTALLATION 3.1 Unpack and inspect ............................................................................................... 3-1

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL iii

3.3.3 Control power ...................................................................................................................... 3-16

4 INTERFACES 4.1 EnerVista software interface................................................................................4-1

iv B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

4.2.5 Front panel labelling .........................................................................................................4-42

5 SETTINGS 5.1 Settings menu......................................................................................................... 5-1

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL v

5.6.4 Breaker failure (ANSI 50BF)......................................................................................... 5-162

6 ACTUAL VALUES 6.1 Actual Values menu ...............................................................................................6-1

vi B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

6.5.1 User-programmable fault reports..............................................................................6-12

7 COMMANDS AND 7.1 Commands menu ................................................................................................... 7-1

8 APPLICATION OF 8.1 Overview.................................................................................................................. 8-1

9 THEORY OF 9.1 Introduction ............................................................................................................ 9-1

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL vii

9.6.1 Output logic .............................................................................................................................9-9

10 MAINTENANCE 10.1 Monitoring .............................................................................................................10-1

A FLEXANALOG A.1 FlexAnalog items ................................................................................................... A-1

B RADIUS SERVER B.1 RADIUS server configuration ................................................................................B-1

C COMMAND LINE C.1 Command line interface ....................................................................................... C-1

D MISCELLANEOUS D.1 Warranty ................................................................................................................. D-1

viii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

This chapter outlines safety and technical support information.

1.1 Safety symbols and definitions

Indicates practices not related to personal injury.

1.1.1 General cautions and warnings

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 1-1

1.2 For further assistance

1-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Figure 1-1: Generate service report in EnerVista software

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 1-3

1-4 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Chapter 2: Product description

This chapter outlines the product, order codes, and specifications.

2.1 Product description

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 2-1

2-2 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Figure 2-1: Single-line diagram

and dynamic bus replica

50BF 50BF 50BF 50BF

50EF 50EF 50EF 50EF

voltage, and frequency

B90 Low Impedance Bus Differential System

Table 2-2: Other device functions

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 2-3

2.2.0.1 EnerVista security

2.2.0.2 Password security

2-4 B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

Figure 2-2: Access control by passwords and connection type

2.2.0.3 CyberSentry security

CyberSentry user roles

B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL 2-5

Figure 2-3: CyberSentry user roles

The table lists user roles and permissions.

Table 2-3: Permissions by user role with CyberSentry

B90 - * ** - H * * - F - H - L - N - S - U - W/X ** Full Size Horizontal Mount

B90 - * ** - H * * - F - H - L - N - S - U - W/X ** Full Size Horizontal Mount

B90 - * ** - H * * - F - H - L - N - S - U - W/X ** Full Size Horizontal Mount