Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

DVR User Manual: For H.264 4/8-Channel Digital Video Recorder All Rights Reserved

Download as pdf or txt
Download as pdf or txt
You are on page 1of 67

DVR User Manual

For H.264 4/8-channel digital video recorder


All rights reserved

Downloaded from www.Manualslib.com manuals search engine


DVR User Manual

CAUTION
 Please read this user manual carefully to ensure that you can use the device correctly and
safely.
 There may be several technically incorrect places or printing errors in this manual. The
updates will be added into the new version of this manual. The contents of this manual are
subject to change without notice.
 This device should be operated only from the type of power source indicated on the
marking label. The voltage of the power must be verified before using. If the device doesn’t
work for a long time, pull out the plug from the socket.
 Do not install this device near any heat sources such as radiators, heat registers, stoves or
other device that produce heat.
 Do not install this device near water. Clean only with a dry cloth.
 Place the device in a well-ventilated area.
 Do not power off the DVR at normal recording condition! The correct operation to shut
off DVR is to stop recording firstly, and then to select “shut-down” button at the right of the
menu bar to exit, and finally to cut off the power.
 This machine is indoor using equipment. Do not expose the machine in rain or moist
environment. In case any solid or liquid get into the machine’s case, please cut off the power
supply immediately, and ask for qualified technicians to check the machine before restart
 Do not try to repair the device by yourself without technical aid or approval.
 When this product is in use, the relevant contents of Microsoft, Apple and Google will
be involved in. The pictures and screenshots in this manual are only used to explain the
usage of our product. The ownerships of trademarks, logos and other intellectual properties
related to Microsoft, Apple and Google shall belong to the above-mentioned companies.
 This manual is suitable for 4/8-channel digital video recorders. All examples and
pictures used in the manual are from 4-channel DVR.

Downloaded from www.Manualslib.com manuals search engine


DVR User Manual

Table of Contents
1 Introduction................................................................................................................. 1
1.1 DVR Introduction .......................................................................................................... 1
1.2 Main Features................................................................................................................ 1

2 Hardware Installation ................................................................................................. 3


2.1 Install Hard Drive &DVD Writer ................................................................................... 3
2.1.1 Install Hard Drive ....................................................................................................... 3
2.1.2 Install DVD Writer ..................................................................................................... 3
2.2 Front Panel Descriptions ................................................................................................ 4
2.3 Rear Panel Instructions .................................................................................................. 4
2.4 Remote Controller ......................................................................................................... 6
2.5 Control with Mouse ....................................................................................................... 7
2.5.1 Connect Mouse........................................................................................................... 7
2.5.2 Use Mouse ................................................................................................................. 7

3 Basic Function Instruction .......................................................................................... 9


3.1 Power On/Off ................................................................................................................ 9
3.1.1 Power On ................................................................................................................... 9
3.1.2 Power Off ................................................................................................................... 9
3.2 Login ............................................................................................................................ 9
3.3 Live Preview ................................................................................................................ 10
3.4 Live Playback ............................................................................................................... 10

4 Main Menu Setup Guide ............................................................................................ 12


4.1 Basic Configuration ...................................................................................................... 13
4.1.1 System ...................................................................................................................... 13
4.1.2 Time & Date .............................................................................................................. 14
4.1.3 DST .......................................................................................................................... 14
4.2 Live Configuration ....................................................................................................... 15
4.2.1 Live........................................................................................................................... 15
4.2.2 Main Monitor ............................................................................................................ 15
4.2.3 Mask ......................................................................................................................... 16
4.3 Record Configuration ................................................................................................... 17
4.3.1 Enable ....................................................................................................................... 17
4.3.2 Record Bitrate ........................................................................................................... 17
4.3.3 Time .......................................................................................................................... 18
4.3.4 Stamp ........................................................................................................................ 19
4.3.5 Recycle Record.......................................................................................................... 20
4.3.6 Snap .......................................................................................................................... 20
4.4 Schedule Configuration................................................................................................. 20
4.4.1 Schedule.................................................................................................................... 20
4.4.2 Motion Schedule........................................................................................................ 21
4.4.3 Sensor Schedule......................................................................................................... 21
4.5 Alarm Configuration ..................................................................................................... 21
4.5.1 Sensor Alarm ............................................................................................................. 22
4.5.2 Motion Alarm ............................................................................................................ 23

Downloaded from www.Manualslib.com manuals search engine


DVR User Manual

4.5.3 Video Loss................................................................................................................. 25


4.5.4 Other Alarm............................................................................................................... 25
4.5.5 Alarm Out ................................................................................................................. 26
4.6 Network Configuration ................................................................................................. 26
4.6.1 Network .................................................................................................................... 26
4.6.2 Sub Stream ................................................................................................................ 27
4.6.3 Email ........................................................................................................................ 28
4.6.4 Server........................................................................................................................ 29
4.6.5 Other Settings ............................................................................................................ 29
4.7 User Management Configuration................................................................................... 32
4.8 P.T.Z Configuration ...................................................................................................... 33
4.9 Advanced ..................................................................................................................... 37
4.9.1 Reset ......................................................................................................................... 37
4.9.2 Import/Export ............................................................................................................ 37
4.9.3 Block/Allow List ....................................................................................................... 37

5 Search, Playback & Backup ....................................................................................... 38


5.1 Time Search ................................................................................................................. 38
5.2 Event Search ................................................................................................................ 38
5.3 File Management .......................................................................................................... 39
5.4 Search by Image ........................................................................................................... 40
5.5 Backup......................................................................................................................... 40

6 Manage DVR .............................................................................................................. 42


6.1 Check System Information ............................................................................................ 42
6.1.1 System Information.................................................................................................... 42
6.1.2 Event Information ...................................................................................................... 42
6.1.3 Log Information......................................................................................................... 42
6.1.4 Network Information ................................................................................................. 42
6.1.5 Online Information .................................................................................................... 42
6.1.6 Record Information .................................................................................................... 42
6.2 Manual Alarm .............................................................................................................. 42
6.3 Disk Management......................................................................................................... 42
6.4 Upgrade ....................................................................................................................... 43
6.5 Logoff .......................................................................................................................... 43
7 Remote Surveillance ................................................................................................... 44
7.1 IE Remote Surveillance ................................................................................................ 44
7.1.1 On LAN .................................................................................................................... 44
7.1.2 On WAN ................................................................................................................... 44
7.2 Remote Surveillance through Apple PC ......................................................................... 45
7.2.1 On LAN .................................................................................................................... 45
7.2.2 On WAN ................................................................................................................... 47
7.3 The Remote Live Preview ............................................................................................. 47
7.4 Remote Playback & Backup.......................................................................................... 49
7.4.1 Remote Playback ....................................................................................................... 49
7.4.2 Remote Backup ......................................................................................................... 52
7.5 Remote System Configuration....................................................................................... 52
7.6 Tools ............................................................................................................................ 53
7.7 Remote Management .................................................................................................... 53

Downloaded from www.Manualslib.com manuals search engine


DVR User Manual

Appendix A FAQ............................................................................................................ 54
Appendix B Calculate Recording Capacity ................................................................... 58
Appendix C Compatible Devices ................................................................................... 59
Appendix D 4 CH Specifications ................................................................................... 60
Appendix E 8 CH Specifications.................................................................................... 61

Downloaded from www.Manualslib.com manuals search engine


DVR User Manual

1 Introduction
1.1 DVR Introduction
This model DVR (Digital Video Recorder) is designed specially for CCTV system. It adopts
high performance video processing chips and embedded Linux system. Meanwhile, it utilizes
many most advanced technologies, such as standard H.264 with low bit rate, Dual stream,
SATA interface, VGA output mouse supported, IE browser supported with full remote control,
mobile view(by phones), etc., which ensure its powerful functions and high stability. Due to
these distinctive characteristics, it is widely used in banks, telecommunication, transportation,
factories, warehouse, and irrigation and so on.

1.2 Main Features


COMPRESSION FORMAT
• Standard H.264 compression with low bit rate and better image quality
LIVE SURVEILLANCE
• Supports HDMI/ VGA/CVBS output
• Supports channel security by hiding live display
• Display the local record state and basic information
• Supports USB to make full control
RECORD MEDIA
• Supports two SATA HDDs to record for a longer time without any limitation
BACKUP
• Supports USB 2.0 devices to backup
• Supports built-in SATA DVD writer to backup
• Supports saving recorded files with AVI standard format to a remote computer through
internet
RECORD & PLAYBACK
• Record modes: Manual, Schedule, Motion detection and Sensor alarm recording
• Supports recycle after HDD full
• Resolution, frame rate and picture quality are adjustable
• 4/8 CH SDI real time recording
• 4 audio channels available
• Three record search modes: time search, event search and image search
• 4 screen playback simultaneously
• Supports deleting and locking the recorded files one by one
• Supports remote playback in Network Client through LAN or internet
ALARM
• 4 CH DVR supports 4 channel alarm output and 4 channel alarm input
• 8 CH DVR supports 1 channel alarm output and 8 channel alarm input
• Supports schedule for motion detection and sensor alarm

1
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

• Supports pre-recording and post recording


• Supports linked channels recording once motion or alarm triggered on certain channel
• Supports linked PTZ preset, auto cruise and track of the corresponding channel
PTZ CONTROL
• Supports various PTZ protocols
• Supports 128 PTZ presets and 8 auto cruise tracks
• Supports remote PTZ control through internet
SECURITY
• Customize user right: log search, system setup, two way audio, file management, disk
management, remote login, live view, manual record, playback, PTZ control and remote live
view
• Supports 1 administrator and 63 users.
• Supports event log recording and checking, events unlimited
NETWORK
• Supports TCP/IP, DHCP, PPPoE, DDNS protocol
• Supports IE browser to do remote view
• Supports setup client connection amount
• Supports dual stream. Network stream is adjustable independently to fit the network
bandwidth and environment.
• Supports picture snap and color adjustment in remote live
• Supports remote time and event search, and channel playback with picture snap
• Supports remote PTZ control with preset and auto cruise
• Supports remote full menu setup, changing all the DVR parameters remotely
• Supports mobile surveillance by phones with iPhone, Android & Blackberry OS
• Supports CMS/NVMS to manage multi devices on internet

2
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

2 Hardware Installation
2.1 Install Hard Drive &DVD Writer
2.1.1 Install Hard Drive

Check the unit and the accessories after getting the DVR. Please don’t power up the unit till
the physical installation is complete.

Notice: 1. This series support two SATA hard drives. Please use the hard drive the
manufacturers recommend specially for security and safe field.
2. Please calculate HDD capacity according to the recording setting. Please refer to
“Appendix B Calculate Recording Capacity”.

Step 1: Unscrew and open the top cover.


Step 2: Connect the power and data cables. Place the HDD onto the bottom case as Fig 2-1.
Step 3: Screw the HDD as Fig 2-2.

Fig 2-1 Connect HDD Fig 2-2 Screw HDD

Note: For convenience installation, please connect the power and data cables first and
then wind the screws to fix the HDD.

2.1.2 Install DVD Writer


Step 1: Unscrew and open the top cover.
Step 2: Connect the power and data cable. Place the DVD writer onto the bottom case as Fig
2-3.
Step 3: Screw the HDD as Fig 2-4.

Fig 2-3 Connect the DVD Writer Fig 2-4 Screw the Writer

3
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Note: The writer which is for backup only must be the compatible device we recommend.
Please refer to “Appendix C Compatible Devices”.

2.2 Front Panel Descriptions

Notice: The front panel descriptions are only for reference; please make the object as
the standard.

Type Name Description


Power The power indicator turns blue when DVR is powered up.
HDD The light turns blue when HDD is writing and reading.
Work
Net The light turns blue when it is able to access the network.
state
Backup The light turns blue when backing up files and data.
indicator
Play The light turns blue when playing video.
REC The light turns blue when recording.
Number 1~9 Input number 1~9 or choose camera
MENU/+ 1. Enter menu in live 2. Increase the value in setup
BACKUP/- 1. Decrease the value in setup 2. Enter backup mode in live

Function 0/10+ Input number 0, 10, and the above number together with other digital keys

button Focus 1. Record manually 2. FOCUS function enables at PTZ mode.


Speed 1. Rewind key 2. SPEED function enables at PTZ mode
IRIS 1. Enter play interface 2. IRIS function enables at PTZ mode
P.T.Z 1. Fast forward 2. Enter PTZ mode in live
Direction button Change direction to select items.
Input
Multi-screen Change screen display mode like1/4/8 channel.
button
Enter button Confirm selection.
IR
IR For remote controller
receiver
To connect external USB devices like USB flash, USB HDD for backup or
USB USB port
update firmware; or connect to USB mouse.

2.3 Rear Panel Instructions

Fig 2-5 Rear Panel for 4-ch

4
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

NO. Name Description


1 ALARM OUT Alarm outputs; connect to external alarm
2 ALARM IN Alarm inputs for connecting sensors
3 P/Z Connect to speed dome
4 K/B Connect to keyboard
5 CVBS CVBS output
6 AUDIO OUT Audio out, connect to sound box
7 MIC IN Talk, connect to microphone
8 AUDIO IN Audio inputs
9 HD SDI Video IN HD SDI video inputs
10 HDMI port Connect to high-definition display device
11 VGA port VGA output, connect to monitor
12 LAN port Network
13 USB port Connect external USB devices like USB flash drive, HDD
14 Power Supply DC12V

Fig 2-6 Rear Panel for 8-ch

Item Name Description


1 Alarm Out 1-ch relay output. Connect to external alarm.
2 GND Grounding
3 Y/Z Connect to speed dome, Y is TX+; Z is TX-
4 A/B Connect to keyboard; A is TX +; B is TX-
5 CVBS Port CVBS video signal output
6 Audio Out Audio output, connect to the sound box
7 Audio In 4-ch audio inputs
8 Alarm In Connect to external sensor1-8
9 HDSDI Video In 8-ch SDI video inputs
10 HDMI Port Connect to high-definition display device
11 VGA Connect to monitor
12 LAN Network port
To connect external USB devices like USB flash, USB HDD for backup
13 USB Port
or update firmware; or connect to USB mouse
14 DC 12V Power input

5
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

2.4 Remote Controller


It uses two AAA size batteries.
Step 1: Open the battery cover of the remote controller.
Step 2: Place batteries. Please take care the polarity (+ and -).
Step 3: Replace the battery cover.

The interface of remote controller is shown in Fig 2-7 Remote Controller.

Button Function
Switch off—to stop DVR. Use it before turning
Power Button off the power
Record Button To record manually
-/-- /0-9 Digital Button Input number or choose camera
Fn1 Button Unavailable temporarily
Multi Button To choose multi screen display mode
Next Button To switch the live image
SEQ To enter into auto dwell mode
Audio To enable audio output in live mode
Switch To switch the output between BNC and VGA
Direction button To move cursor in setup or pan/title PTZ
Enter Button To confirm the choice or setup
Menu Button To enter into menu
Exit Button To exit the current interface
To control PTZ camera. Move
Focus/IRIS/Zoom/PTZ
camera/zoom/IRIS/Focus
Preset Button To enter into preset setting in PTZ mode
Cruise Button To enter into cruise setting in PTZ mode
Track Button To enter into track setting in PTZ mode
Wiper Button To enable wiper function in PTZ mode
Light Button To enable light function in PTZ mode
Clear Button To return to the previous interface
Fn2 Button Unavailable temporarily
Get information about DVR like firmware
Info Button
version, HDD information
To control playback. Play/Pause/Stop/Previous
Section/Next Section/Rewind/Fast Forward
Snap Button To take snapshots manually
Search Button To enter into search mode
To set the start/end time for backup in playback
Cut Button
mode
Backup Button To enter into backup mode
Zoom Button To zoom in the images
Fig 2-7 Remote Controller PIP Button To enter into picture in picture setting mode

Note: Please press P.T.Z button to enter into PTZ setting mode and then choose a
channel and press P.T.Z button again to hide the P.T.Z control panel prior to enabling
preset, cruise, track, wiper or light button.

6
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Key points to check in case the remote doesn’t work.


1. Check batteries polarity.
2. Check the remaining charge in the batteries.
3. Check IR controller sensor for any masking.
4. Check the ID of the remote with respect to the DVR.
If it still doesn't work, please change a new remote controller to try, or contact your dealers.

2.5 Control with Mouse


2.5.1 Connect Mouse
It supports USB mouse through the ports on the rear panel.
If mouse is not detected or doesn't work, check below steps:
1. Make sure the mouse is plugged in the USB mouse port.
2. Try with a good know mouse.

2.5.2 Use Mouse


During live:
Double-click on any camera window to see the full screen. Double-click again to return to the
previous screen.
Right click to reveal the control menu on the screen. Right click again to hide the menu.

In Configuration:
Click to enter a particular option. Right click to cancel the option or to return to the previous
menu.
In order to input a value in a particular screen, move cursor to the input box and click. An
input window will appear as Fig 2-8. It supports digits, alphabets and symbols input. Click
Shift button to input Capital letters and symbols; click Shift button again to return.

It supports mouse drag. Take setting up motion detection area for example: Click customized,
hold down the left button and drag to set motion detection area.

Fig 2-8 Digital Numbers and Letters Input Window


In Playback:
Click to choose the options. Right click to return to live mode.

7
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

In Backup:
Click to choose the options. Right click to return to previous picture.

In PTZ Control:
Click left button to choose the buttons to control the PTZ. Click right button to return to live.

Note: Mouse is the default tool for all operations unless an exception, as indicated.

8
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

3 Basic Function Instruction


3.1 Power On/Off
Before you power on the unit, please make sure all the connection is good.

3.1.1 Power On
Step 1: Connect with the source power.
Step 2: The device will boot and the power LED would turn blue.
Step 3: A WIZZARD window will pop up and show some information about time zone, time
setup, network configuration, record configuration and disk management. User can setup here
and refer to the concrete setup steps from the corresponding chapters. If users don’t want to
setup Wizard, please click Exit button to exit. Long press ESC/Stop key to switch the output
among CVBS, VGA and HDMI.

3.1.2 Power Off


You can power off the device by using remote controller, keyboard and mouse.

By remote controller:
Step 1: Press Power button. This will take you to a Shut down window. The unit will power
off after a while by clicking OK button.
Step 2: Disconnect the power.

By keyboard and mouse:


Step 1: Enter into Menu and then select “Shut Down” icon to pop up the Shut down
window.
Step 2: Click OK. Then the unit will power off after a while.
Step 3: Disconnect the power.

3.2 Login
User can login or log off the DVR system. Once logged off the user cannot do any other
operation except changing the multi-screen display.

9
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 3-1 Login

Notice: The default user name and password is “admin” and 123456”.
For complete operational steps for changing password, adding or deleting users,
please refer to section 4.7 User Management Configuration.

3.3 Live Preview

Fig 3-2 Live Preview Interface

Symbol Meaning
Green Manual record
Yellow Motion detection record
Red Sensor Alarm record
Blue Schedule record

3.4 Live Playback


Click Playback button to playback the record. Refer to Fig 3-3. User can do complete
operation by clicking the buttons on screen.

10
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 3-3 Live Playback

11
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

4 Main Menu Setup Guide


Click right mouse or press ESC/Stop button on the front panel and then the control bar will
display at the bottom of the screen. Refer to Fig 4-1:

Fig 4-1 Main Menu Toolbar

Single: Choose a channel from the list to be displayed in the full screen mode.
Multi: Choose the display mode for viewing multiple channels.
Dwell: Dwell means to display live images from different cameras in a sequence. The images
may be displayed as a single channel or in a grid fashion from different cameras. Dwell mode
is enabled only when the chosen display mode is not able to display all the available cameras.
E-Zoom: Single channel large screen electronic amplification.
Audio: Enable sound.
PTZ: Click the PTZ button to control rotation position, speed and auto scan of the PTZ.
Snap: Click this button to snap the live pictures. These pictures will automatically be saved in
the SATA disk.
Record: Click this button to start/stop recording.
Playback: Click this button to playback the record files.
Click Menu button to pop up a window as Fig 4-2. You can also press MENU button on
the front panel or operate with remote controller to display the main menu. Clicking Setup
icon will pop-up the configuration menu:

Fig 4-2 Setup

12
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

4.1 Basic Configuration


Basic configuration includes three sub menus: system, date & time and DST.

4.1.1 System
Step 1: Enter into MenuSetupBasic System interface. Refer to Fig 4-3:

Fig 4-3 Basic Configuration-System

Step 2: In this interface you can setup the device name, device ID, video format, max network
users, VGA resolution, language and so on. The definitions for every parameters display as
below:
Device Name: The name of the device. It may display on the client end or CMS that help user
to recognize the device remotely.
Device ID: This ID is used to map the DVR with IR remote controller and speed dome
cameras.
Video Format: Two modes: PAL and NTSC. User can select the video format according to
that of camera.
Password Check: If this option is enabled, the user would need to input the user name and the
password for performing corresponding operations.
Show System Time: If selected, the current time will be displayed during live monitoring.
Max Online Users: To set the max number of concurrent user logins in the DVR.
Video Output: The resolution of live display interface.
Language: Setup the menu language.

Note: After changing the language and video output, the device needs to login again.

Logout After (Minutes): A user can setup the screen interval time (30s, 60s, 180s, 300s). If
there is no any operation within the setting period, the device will auto logout and return to
login interface.

13
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Show Wizard: If selected, the GUI would launch the startup wizard on every boot, allowing
the user to do basic setup.
No Image When Logout: If selected, there will be no image showing when logging out.
Adjust CVBS Video Out: If selected, the system will automatically log out and adjust the
CVBS output. Only some models are able to support this function. Please take the real object
as standard.

4.1.2 Time & Date


Step 1: Enter into MenuSetupBasic Date & Time interface. Refer to Fig 4-4:

Fig 4-4 Basic Configuration-Date & Time

Step 2: Set the date format, time format, time zone in this interface; checkmark “sync time
with NTP server” to refresh NTP server date. You can also adjust system date manually.
Step 3: Click “Apply” button to save the setting.

4.1.3 DST
Step 1: Enter into MenuSetupBasic DST interface. Refer to Fig 4-5:

Fig 4-5 Basic Configuration-DST

Step 2: In this interface, enable daylight saving time, time offset, mode, start & end

14
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

month/week/date, etc.
Step 3: Click “Apply” button to save the setting.

4.2 Live Configuration


Live configuration includes three submenus: live, main monitor and mask.

4.2.1 Live
In this interface, you can setup camera name.

To setup camera name:


Step 1: Enter into MenuSetupLive. Refer to Fig 4-6:

Fig 4-6 Live ConfigurationLive

Step 2: A software keyboard will pop up by clicking camera name area. Click the letters and
(or) digital numbers on the keyboard to input the name you want to display in live image.
Step 3: Checkmark the camera name in the show name area.
All channels will show the camera name by checking “All” checkbox.
Step 4: Click “Apply” to save the setting.

4.2.2 Main Monitor


The main monitor settings allow you to set camera sequence in live display mode.
Operate the following steps to set main monitor:
Step 1: Enter into MenuSetupLive Main Monitor interface. Refer to Fig 4-7:
Step 2: Select display mode and channel.
Step 3: Select dwell time. Click button to setup the previous channel groups of dwell
picture. Click button to set the latter channel groups of dwell picture.
Step 4: Click “Apply” to save the setting.

15
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-7 Live Configuration-Main Monitor

4.2.3 Mask
If there is something you don’t want to display in the live image. You can set mask. For a
given channel a maximum of three areas can be masked.

To setup mask area:


Step 1: Enter into MenuSetupLive Mask interface.

Fig 4-8 Live Configuration-Mask

Step 2: Click Setting button to go into live image.


Step 3: Press and drag the left mouse button to set mask area as shown below.
Step 4: Right click to exit the mask setting interface.
Step 5: Click Apply button to save the setting.

To delete mask area


Step 1: Click Setting button in the mask interface.
Step 2: Select a certain masked area and double click to delete that masked area.
Step 3: Then click Apply button to save the setting.

16
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-9 Setting Mask Area

4.3 Record Configuration


Record configuration includes six sub menus: enable, record bit rate, time, recycle record,
stamp and snap.
Before Configuration, please make sure your DVR has been installed with HDD and has
completed its initialization.

4.3.1 Enable
Step 1: Enter into MenuSetupRecordRecord interface. Refer to Fig 4-10:

Fig 4-10 Record Configuration-Record

Parameter Meaning
Record To enable/disable recording for the channel
Audio To enable/disable audio recording for the channel

Step 2: Checkmark record and audio.


Step 3: Select All to setup the same settings for all channels.

4.3.2 Record Bitrate


Step 1: Enter into MenuSetupRecord Record Bitrate. Refer to Fig 4-11:

17
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 2: Setup rate, resolution, quality, encode and max bit stream.
Step 3: Select “All” to set the same settings for all channels.
Step 4: Click “Apply” button to save the setting.

Fig 4-11 Record Configuration-Record Bitrate

Parameter Meaning
Rate Range from: 1-30(NTSC)1-25(PAL)
Resolution 4 CH DVR supports1080P; 8 CH DVR supports 720P, 1080P
The higher the value is, the clearer the recorded image is. Six options:
Quality
lowest, lower, low, medium, higher and highest.
Encode VBR and CBR
Max bit stream Adjust subject to the actual network condition

4.3.3 Time
Step 1: Enter into MenuSetupRecord  Time interface to set recording time. Refer to Fig
4-12:

Fig 4-12 Record Configuration-Time

Step 2: Set Pre-alarm record time and post-alarm record time. Select “All” to set the same
settings for all channels.
Pre-alarm Record Time: Set the time in seconds to pre-record before the actual recording

18
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

begins.
Post-alarm Record Time: Set the time in seconds to post-record after the actual recording
has finished, five options: 10s, 15s, 20s, 30s, 60s, 120s, 180s and 300s.
Expire Time: Set the expiration time for recorded video. If the set date is overdue, the
recorded files will be deleted automatically.

Step 3: Click “Apply” to save the setting.

4.3.4 Stamp
This provides an option to enable or disable the Camera Name and the Time stamp on the
video. The user can also choose a position for the stamp on the screen.
To setup stamp as follows:
Step 1: Enter into Menu SetupRecordStamp interface. Refer to Fig 4-13:

Fig 4-13 Record Configuration-Stamp

Step 2: Checkmark camera name and time stamp. Click Setting button to setup the position of
the stamp. You can drag the camera name and time stamp at random positions. Refer to below
Figures:

Before drag After drag

Step 3: Select “All” to setup all channels with the same parameters.

19
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

4.3.5 Recycle Record


This option is used to recycle the HDD space once it is full. If enabled, the system will
automatically delete the old records and recycle the space if it is completely utilized. The
setting steps are as follows:
Step 1: Enter into MenuSetupRecord Recycle Record interface;
Step 2: Checkmark recycle record to activate auto recycling. If the option is disabled or not
selected, the DVR would stop recording once HDD is full.
Step 3: Click “Apply” button to save the setting.

4.3.6 Snap
In this interface, user can set up Resolution, quality, snap interval, snap number.

4.4 Schedule Configuration


Schedule configuration includes three sub menus: schedule, motion and sensor.

4.4.1 Schedule
This tab allows defining schedule for normal recording for seven days of a week, 24 hours of a
day. Every row denotes an hourly timeline for a day. Click the grid to do relevant setup. A
highlighted area denotes selected timeline. Operate the following steps to set schedule:
Step 1: Enter into MenuSetupSchedule interface. Refer to Fig 4-14:
Step 2: Select channel and click “ ” button to add a certain day schedule. Click “ ”
button to delete the selected schedule.
If you want to apply the schedule setting of a certain channel to other or all channels, you need
to select channel and click “Copy” button.

Fig 4-14 Schedule Configuration-Schedule

You can also set week schedule by double-clicking in the grinding area. This will take you to
see a dialog box as Fig 4-15.
Step 1: Select a day and click “Add” button to schedule start time and end time. Then click

20
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

to save.
Step 2: Select other days and add schedule or copy settings from one schedule to the others
under the Apply Settings To item.

Fig 4-15 Schedule-Week Schedule

4.4.2 Motion Schedule


This tab allows to set schedule for motion based recording. The setting steps are as follows:
Step 1: Enter into MenuSetupSchedule Motion tab.
Step 2: The setup steps for schedule for motion based recording are similar to normal schedule
setup. You can refer to 4.4.1 Schedule for details.

Note: The default schedule of motion based recording is 24 ⅹ7. If


motion based recording, you must enable motion alarm and setup schedule for motion
alarm (see Chapter 4.5.2 Motion Alarm for more details).

4.4.3 Sensor Schedule


This tab allows to set schedule for sensor based recording. The setting steps are as follows:
Step 1: Enter into MenuSetupScheduleSensor interface.
Step 2: The setup steps for schedule for sensor based recording are similar to normal schedule
setup (see Chapter 4.4.1 Schedule for details).

Note: The default schedule of sensor based recording is 24 ⅹ7. If


sensor based recording, you must enable sensor alarm and setup schedule for sensor
alarm (see Chapter 4.5.1 Sensor Alarm for more details).

4.5 Alarm Configuration


Alarm configuration includes five sub menus: sensor, motion, video loss, other alarm and
alarm out.

21
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

4.5.1 Sensor Alarm


Sensor includes three sub menus: basic, alarm handling and schedule.
Operate the following steps to configure sensor alarm:
Step 1: Enter into MenuSetupAlarm SensorBasic interface. Refer to Fig 4-16:

Fig 4-16 Alarm Configuration-Sensor-Sensor

Step 2: Enable channels by checking the checkboxes beside the desired channels.
Step 3: Set the alarm type according to triggered alarm type. Two option: NO and NC.
Step 4: Click “Apply” button to save the setting.
Step 5: Enter into Alarm Handling tab. Refer to Fig 4-17. Select hold time and then click
“Setting” button to pop up a dialog box as shown in Fig 4-18.

Fig 4-17 Alarm Configuration-Sensor-Alarm Handling

Step 6: Enter into alarm tab to select the options to handle alarm.

22
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-18 Alarm Handling-Trigger

Buzzer: If selected, the local buzzer would be activated on an alarm.


Show Full Screen: If selected, there will pop up the chosen channel on the monitor on an
alarm trigger.
To Alarm Out: If selected, this would trigger the external relay output on detecting a sensor
based alarm.
Email: If selected, the DVR will send an email alert to the preconfigured email address in
case of a sensor based alarm from the particular input.
Snap: If selected, the system will snap images of the checked channels on an alarm and save
them in the HDD automatically.

Step 7: Enter into To Record tab. Select recording channels. It would be recorded in case of an
alarm. Click OK button to save the setting.
Step 8: Enter into To PTZ tab. Set preset, cruise and track options for a PTZ in case of a
sensor based alarm. Single or multiple PTZ units could be programmed to perform this
function on the same alarm.
Step 9: Enter into Schedule tab. The setting steps for schedule for sensor based alarm are
similar to normal schedule setup. You can refer to 4.4.1 Schedule for details. This step is very
important for sensor alarm. Even if you have enabled the sensor alarm for all channels and
setup the trigger, you will not see the result of sensor alarm if no schedule is added.
If you have set schedule for sensor based recording in the same timeline, recordings can also
be triggered.

4.5.2 Motion Alarm


Motion includes two sub menus: motion and schedule. The steps to set motion alarm are as
follows:
Step 1: Enter into MenuSetupAlarm MotionMotion tab. Refer to Fig 4-19:
Step 2: Enable motion alarm, set alarm hold time which refers to the time till which the
system will wait for further detection of motion. e.g. If the holding time is set to 10 seconds,
once the system detects a motion, it will go into alarm but would not detect any other motion
alarm (specific to channel) until 10 seconds. If there is other motion detected during this
period it is considered it as continuous movement, otherwise it will be considered as a single

23
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

motion.

Fig 4-19 Alarm Configuration-Motion

Step 3: The setup steps of motion trigger are similar to “Alarm Handling” (See Chapter 4.5.1
Sensor Alarm Handling setting for more details).
Step 4: After clicking Area button, a dialog box will pop-up as Fig 4-20:
Step 5: In the Area interface, you can drag slide bar to set the sensitivity value (1-8). The
higher the value is the more sensitive it is to motion. Since the sensitivity is influenced by
color and time (day or night), you can adjust its value according to the practical conditions.
Left click the grid and drag to delete area. Click icon to set the whole area as detection
area. Click icon to clear the set detection area. Click icon to test the sensitivity as
per the local conditions. Once motion is sensed, it displays a figure icon. Click icon, to
save the setting. Click icon to exit the current interface.

Fig 4-20 Motion-Area

Note: Prior to setting motion detection field it is recommended that you click
icon to clear the existing field and set afresh.

Step 6: Select “All” to set the same settings for all channels.

24
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 7: Click “Apply” button to save the setting.


Step 8: Enter into Schedule tab. The setting steps for schedule for motion based alarm are
similar to normal schedule setup (see Chapter 4.4.1 for more details).

4.5.3 Video Loss


This DVR can be set up to detect video loss. The setting steps are as follows:
Step 1: Enter into MenuSetupAlarm Video Loss. Refer to Fig 4-21:
Step 2: The setup steps of video loss trigger are similar to “Alarm Handling” (See Chapter
4.5.1 Sensor Alarm Handling setting for more details).

Fig 4-21 Alarm Configuration-Video Loss

4.5.4 Other Alarm


This tab gives a choice to configure alarm for Disk Full, IP Conflict, the Disconnect event,
Disk Attenuation or Disk Lost.
Step 1: Enter into Menu  Setup Other Alarm. Refer to Fig 4-22:

Fig 4-22 Other Alarm

Step 2: Use the dropdown menu and select the event or the alarm.
Step 3: Check the required trigger options.
If the selected event is “Disk Full”, then use the drop down box for “Disk Shortage Alarm” to

25
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

choose a threshold value for remaining HDD space. If the threshold value is reached, the
system will trigger the Disk Full Alarm.
Step 4: Click “Apply” to save the setting.

4.5.5 Alarm Out


Alarm out includes three sub menus: alarm out, schedule and buzzer.

To setup alarm out:


Step 1: Enter into MenuSetupAlarm Out. Refer to Fig 4-23:

Fig 4-23 System Configuration-Alarm Out

Step 2: Input relay name and select hold time.


Step 3: Enter into Schedule tab. This will go into schedule setup interface. The setting steps
for schedule for alarm out are similar to normal schedule setup (see Chapter 4.4.1 for details).
This step is very important for alarm out. Even if you have enabled alarm out in the motion
based alarm or sensor based alarm, you will not see the result of alarm out if no schedule is
added here.

To set up buzzer:
Step 1: Enter into MenuSetupAlarm Out Buzzer.
Step 2: Checkmark Buzzer and set buzzer alarm hold time. This would trigger the buzzer
when the system is on an alarm.

4.6 Network Configuration


Network configuration includes five submenus: network, sub stream, Email, server and other
settings. Network settings must be configured if DVR is used for monitoring over network.

4.6.1 Network
To set up network:
Step 1: Enter into MenuSetupNetworkNetwork tab. Refer to Fig 4-24:

26
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-24 Network Configuration-Network

Step 2: Set HTTP port. The default HTTP port is 80. If the value is changed, you shall add the
port number when typing IP address in IE address blank. e.g. If HTTP port is set to 82 and IP
address is http://192.168.11.61, you should input the following IP address:
http://192.168.11.61 :82 into IE browser.
Step 3: Set server port. The default server port is 6036.
Step 4: Connect internet. There are three ways to connect internet.

 If you have a DHCP server running and would like your DVR to automatically obtain an
IP address and other network settings, check the checkbox beside "Obtain an IP address
automatically". Then the device will distribute IP address, subnet mask, and gateway IP
and DNS server.
 If you want to configure your own settings, disable “Obtain an IP address automatically”
item and input the IP address, subnet mask, gateway IP and DNS server.
 If you connect internet through PPPoE, disable “Obtain an IP address automatically”
item and check PPPoE checkbox and then enter username and password. Once the setup
is completed, your DVR will automatically dial up into your network.

Step 5: Test the effectiveness of the network by clicking “Test” button after you set up the
network.
Step 6: If the network is well connected, please click “Apply” button to save the setting.

4.6.2 Sub Stream


To setup sub stream:
Step 1: Enter into MenuSetupNetwork Sub Stream interface. Refer to Fig 4-25:
Step 2: Select fps, resolution, quality, encode and max bit rate
Step 3: Select “All” to set the same settings for all channels.

27
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-25 Network Configuration-Sub Stream

Parameter Meaning
FPS Range from: 1-25
Resolution Support CIF
The quality of the clients’ image. The higher the value is, the
Quality clearer the record image. Six options: lowest, lower, low, medium,
higher and highest.
Encode VBR and CBR
Max bit rate Range from: 256~1792kbps

4.6.3 Email
To set up Email:
Step 1: Enter into MenuSetup NetworkEmail interface. Refer to Fig 4-26:
Step 2: Set SMTP Server and port.

Fig 4-26 Network Configuration-Email

SMTP Server/Port: The name and port number of SMTP server. You can setup SSL check
(such as Gmail) according to actual needs.
Step 3: Set sender’s address and password.

28
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 4: Set receiver’s email address and click “Test” button to test the validity of the mailbox.
Attaching image: If selected, the system will attach images when sending emails.

4.6.4 Server
This function is mainly used for connecting ECMS/NVMS. The setting steps are as follows:
Step 1: In the server interface, select “Enable” as shown in the Fig 4-27.

Fig 4-27 Network Configuration-Server

Step 2: Check the IP address and port of the transfer media server in the ECMS/NVMS. The
default server port for auto report is 2009. If it is modified, please enter into the transfer media
interface to check.
Step 3: Enable the auto report in the ECMS/NVMS when adding a new device. Then input the
remaining information of the device in the ECMS/NVMS. After that, the system will auto allot
a Device ID. Please check it in the ECMS/NVMS.
Step 4: Input the above-mentioned server IP, server port and device ID in the server interface.
Then click “Apply” button to save the setting. Now, the ECMS/NVMS system will
automatically connect this device.

4.6.5 Other Settings


If your DVR is set to use PPPoE as its default network connection, you may setup DDNS to
be used in connection. The setting steps are as follows:
Step 1: Enable DDNS server.
Step 2: Select DDNS server.
Step 3: Enter user name, password and host domain name of the registered website.
Step 4: Click “Test” button to test the effectiveness of the relevant information.
Step 5: Click “Apply” button to save the setting.

29
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-28 Network Configuration-Other Settings

Note: The domain name selected by user is a banding domain name of DVR. User
should logon the website provided by the server supplier to register a user name and
password and then apply for a domain name online. After the successful application,
user can access the device from the IE client by inputting that domain name.

Enable UPnP: Select UPnP here and then enable UPnP function in your router. Therefore,
there is no need for you to forward LAN IP address and port in the router in connection of
internet. After that, you can check the WAN IP address in the router.

 Domain name Registration (Take www.dvrdydns.com for example)

Step 1: Input www.dvrdydns.com in the IE address bar to visit its website. Then click
“Registration” button to register as shown below.

Step 2: Create domain name.

30
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 3: After you successfully request your domain name, you will see your domain in the list.

 DVR Setting
Connect DVR to the Network Client.
Step 1: Enter into Main menuNetworkOther Settings, checkmark DDNS, select
“dvrdydns” at the DDNS Sever pull down list box and input user name and password.
Step 2: Enter into configuration interface of the router to map the server port and IP address (if
the user enables UPnP function, he can skip this step). Click Save button to save the setting
Step 3: Login IE browser and input registered domain name “http://www.xxx.dvrdydns.com:
port”, connect to DVR client.

You can also quickly register the domain name in this interface.
Step 1: Set the IP address manually in the network tab and then click “Other Settings” tab.

Step 2: Check “DDNS”.


Step 3: Select “www.autoddns.com” in DDNS Type column as shown above.
Step 4: Enter the host name at random, like 123.
Step 5: Click “Register” to register the domain name. When the successful prompt pops up, it
means you are successfully register your domain name.
If your IP address is not WAN IP address, you should forward your IP address and port in your
router or enable UPNP function both in router and DVR. Then you can use the domain name

31
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

plus HTTP port to access your DVR.

DDNS server
Website provided by dynamic domain name supplier. The optional: www.meibu.com ,
DDNS server www.dyndns.com, www.no-ip.com, www.dvrdydns.com, www.autoddns.com and
mintdns type.
User name User name for log in the website of domain name supplier
Password Password for log in the website of domain name supplier
Host domain The domain name user registered at the supplier’s website.
Update interval The interval time of upgrading DVR IP address

4.7 User Management Configuration


This tab allows you to add normal or advanced users. To add user and setup user authority:
Step 1: Enter into MenuSetupUsers. Refer to Fig 4-29:

Fig 4-29 User Management Configuration

Step 2: Click Add button to display a dialog box as Fig 4-30:

Fig 4-30 Add-General

32
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 3: In General tab, input username, password and select user type. You can also check
“Binding PC MAC Address” and input this address.
Step 4: Click “OK” to save the setting.
Note: When the default value of binding PC MAC Address is 0, the user is not bound
with the specified computer. If the bind option is used, the user would be able to log
into the DVR only through the specific computer (carrying the MAC address).

Step 5: Select Authority tab and then assign the operation rights for particular user. Refer to
Fig 4-31.
Step 6: Click OK to save the setting.

Fig 4-31 Add User-Authority

To delete user:
Step 1: Enter into MenuSetupUsers interface.
Step 2: Select the added user you want to delete and then click “Delete” button.

To modify user:
Step 1: Enter into MenuSetupUsers interface.
Step 2: Select the added user you want to modify and then click “Modify” button to do the
relevant operation.

To change user password


Step 1: Enter into MenuSetupUsers interface.
Step 2: Select the added user you want to change its password and then click “Change
Password” button.

4.8 P.T.Z Configuration


P.T.Z configuration includes two submenus: serial port and advanced.
Serial port settings are as follows:
Step 1: Enter into MenuSetup  P.T.Z Serial Port interface. Refer to Fig 4-32:

33
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-32 P.T.Z Configuration-Serial Port

Parameter Meaning
Address The address of the PTZ device
Baud rate of the PTZ device. Range form: 110, 300, 600, 1200, 2400,
Baud rate
4800, 9600, 19200, 34800, 57600, 115200, 230400, 460800, 921600.
Communication protocol of the PTZ device. Range from: NULL,
Protocol PELCOP, PELCOD, LILIN, MINKING, NEON, STAR, VIDO,
DSCP, VISCA, SAMSUNG, RM110, HY, N-control.
Simulative If enabled, no matter whether the PTZ device supports cruise or not,
Cruise the presets will cruise.

Step 2: Select “Enable” and setup the value of address, baud rate and protocol according to the
settings of the speed dome.
Step 3: Select “All” to set the same settings for all channels.

Advanced settings include preset setting, cruise setting and track setting.
Enter into MenuSetup P.T.Z Advanced. Refer to Fig 4-33:

Fig 4-33 P.T.Z configuration-advanced

34
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

To set up preset:
Step 1: In the Advanced interface, click preset “Setting” button to see a dialog box as Fig
4-34:

Fig 4-34 Advanced-Preset Setting

Step 2: In the preset setting tab, enable preset, set the preset name and then click preset
“Setting” button.

Fig 4-35 Preset Setting

Step 3: Control the dome by rotating up, up left, down, right down, left, left down, right and
up right and adjust the rotate speed and the value of zoom, focus and iris of the dome.
Step 4: Select the serial number of the preset point. Click button to enable the PTZ wiper
and click button to enable the PTZ light.

Note: PTZ must support wiper and light button and these two buttons are just available
when selecting PELCOP or PELCOD.

Step 5: Click Save button to save the setting. Click icon to hide the tool bar. Right click
to view this bar again. Click icon to exit the current interface.
Step 6: Return to the Advanced-Preset Setting interface and click OK button to save the setting.

To set up cruise:
Step 1: In the Advanced interface, click cruise “Setting” button to see a window as shown in
Fig 4-36:

35
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-36 Cruise Setting

Step 2: Click Add button to add cruise line in the list box (8 cruise lines can be added at most).
Step 3: Select a cruise line and click Setup button to see a dialog box as Fig 4-37:

Fig 4-37 Modifying Cruise Line

Step 4: Click Add icon to set the speed and time of preset point. Select a preset point
and then click Delete icon to delete that preset point. Click Modify icon to modify
the setting of a preset point. User can click those icons to adjust the position
of preset point. Click Preview button to preview the cruise line. Click OK button to save the
setting.

To set up track:
Step1: In the Advanced interface, click track “Setting” button to see a dialog box as Fig 4-38:
Step 2: Control the dome by rotating up, up left, down, right down, left, left down, right and
up right and adjust the rotate speed and the value of zoom, focus and iris of the dome.
Step 3: Click Start Record button to record the move track of PTZ. Click this button again to
stop record.
Step 4: Click Start track button to play recorded track. Click this button again to stop playing.
Step 5: Click icon to exit the current interface.
After the completion of settings, please remember to click “Apply” to save the setting.

36
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 4-38 Track Setting

4.9 Advanced
Advanced configuration includes three submenus: reset, import/export and Block/Allow list.

4.9.1 Reset
Reset all settings the device will reboot.

4.9.2 Import/Export
User can export the data files into mobile storage devices as backup function, and then import
specified data files from mobile storage device to DVR.

4.9.3 Block/Allow List

Fig 4-39 Block/Allow List

Here authorized user can prohibit computer users within a certain IP address range from
accessing to DVR or allow computer users within a certain IP address range to access DVR.
E.g. if an admin user doesn’t want computer users within IP address range from
192.168.000.002 to 192.168.000.004 to access the DVR, he can check Block list option, and
then input such IP address range. If it is required that computer users within a certain IP
address range access DVR, they can check Allow List option and then do the required setting.

37
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

5 Search, Playback & Backup


Search configuration includes four submenus: time search, event search, file management and
image.

5.1 Time Search


Step 1: Enter into MenuSearch Time Search. Refer to Fig 5-1:

Fig 5-1 Search Configuration-Time Search

Step 2: Select date and channels on the right hand side and press the ‘Search’ button. A date
with highlighted borderline indicates presence of data.
Step 3: Set the start time by clicking a particular grid or by entering the specific value in the
start time field.
Step 4: Select the channel display mode and click button to play record. Use the
playback toolbar to control the playback.

 To set backup during a certain period in the playback interface:


Select the start time by dragging the slider and click icon. Then select the end time and
click this icon again to confirm the record period. Next, click icon to backup the record
during this period.

5.2 Event Search


Step 1: Enter into MenuSearchEvent Search button. Refer to Fig 5-2:

38
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 5-2 Search Configuration-Event Search

Step 2: Select date and channels on the right hand side. A data with highlighted borderline
indicates presence of data.
Step 3: Checkmark Motion, Sensor or All accordingly.
Step 4: Click Search button to display the searched event information in the event list box.
Step 5: Double check a certain record file to playback.

5.3 File Management


Step 1: Enter into MenuSearchFile Management interface. Refer to Fig 5-3:

Fig 5-3 Search Configuration-File Management

Step 2: Select date and channels. The date with highlighted borderline indicates presence of
data.
Step 3: Click Search button to display the searched files in the file list box.
Step 4: Use “All” button to lock/unlock or delete all files in the file management column.

39
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 5: Double click an unlocked item to play.


Lock: Select a file and click Lock button to lock this file, after that, that file will not be
deleted or covered.
Unlock: Select a locked file and click “Lock” button to unlock this file
Delete: Select an unlocked file and click “Delete” button to delete this file.

5.4 Search by Image


Step 1: Enter into Menu  Search  Image tab.
Step 2: Select data and channels on the right hand side.
Step 3: Press “Search” button to search for a recorded image.
Step 4: Once an alarm image has been identified, the user can double click the image to play
recording.

Fig 5-4 Search Configuration-Image

Lock: Select the image and click “Lock” button to lock this image.
Save: Click “Save” button to copy the image on the HDD.
Save All: Click “Save All” button to copy all images on the HDD.

5.5 Backup
This unit supports backup by built-in SATA DVD Writer with USB Flash. You can also make
backup by IE browser via internet (see section 7.3.2 Remote backup).
Step 1: Enter into backup configuration. Refer to Fig 5-5:
Step 2: Set the start & end time, select channels and click Search button to display the
searched data in the data backup list box.

40
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 5-5 Backup Configuration

Step 3: Select a required file or checkmark “All” to select all data files. Click Backup button
to display Backup information window.

Step 4: In the backup information interface, you can check the relevant information of backup
files, storage type, save file type, etc. Then click Start button to start backup.

Note: If the backup files are saved in DVR format, please check backup player. Only
this player can play these files in DVR format. If the backup files are saved in AVI
format, you can play these files with common media player.

41
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

6 Manage DVR
6.1 Check System Information
Check system information includes six submenus: system, event, log, network, online user and
record.

6.1.1 System Information


In this interface, you can check the hardware version, MCU version, kernel version, device ID,
etc.

6.1.2 Event Information


In this interface, you can search for events like motion, sensor and video loss. The utility
provides an interface to have a date based and a channel based search. This report can further
be saved on a USB flash drive as an html file using the export button.

6.1.3 Log Information


In this interface, you can search for relevant logs as per set date and event which includes
Operation, Setup, Playback, Backup, Search, Check Information and Error. This report can
further be saved on a USB flash drive as an html file using the export button.

6.1.4 Network Information


In this interface, you can check relevant parameters of network.

6.1.5 Online Information


In this interface, you can check the details of the connected online users.

Refresh: Refresh the current interface.


Disconnect: Disconnect the online users to access DVR. If this function is used by the admin,
the particular PC will not be able to access the device for five minutes.

6.1.6 Record Information


In this interface, a user can check resolution, ftp and record status including sensor alarm
recording, motion recording, manual recording or schedule recording.

6.2 Manual Alarm


In this interface, you can trigger a manual alarm.

6.3 Disk Management


To format the disk

42
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 1: Enter into disk management interface

Note: please format the hard disk before record.

Step 2: Click Refresh button to refresh the disk information in the list box.
Step 3: Select a hard disk and click Format button to start format.

Note: All recorded files in the hard disk will be lost after formatting.

To check other information of disk


After you enter into Disk ManagementAdvanced tab, you can check model, S/N, firmware,
health status of the disk in this interface. You also can monitor the temperature, internal circuit,
dielectric material of the disk, analysis the potential problems of the disk and warn so as to
protect its data.

6.4 Upgrade
At present, it only supports USB update. Get the software from your vendor when there is a
new software version.
The upgrade steps are as follows:
Step 1: Copy the upgrade software which gets from vendor into the USB storage device.
Step 2: Connect the USB flash drive to the USB port.
Step 3: Enter MenuUpgrade tab. You will see the upgrade software name displaying in the
upgrade list box.
Step 4: Select that software and then click Upgrade button. The system will be upgraded
automatically.

Note: Please wait for a while when the system reboots. Any power interruption is not
allowed during upgrading.

6.5 Logoff
A log off dialogue box will pop up by clicking Log off icon. Then click OK button to confirm
to log off. If you want to log in again, click icon to enter user name and password to
re-login.

43
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

7 Remote Surveillance
7.1 IE Remote Surveillance
In order to view the DVR from a network it must be connected to LAN/WAN or internet. The
network setup should be done accordingly. Please refer to 4.6 Network Setup. This DVR
supports IE browser, on Windows XP and Vista platform.

7.1.1 On LAN
Step 1: Enter into the DVR’s Main MenuSetupNetwork interface to input IP address,
Subnet Mask, etc .If using DHCP, please enable DHCP in both the DVR and the router.
Step 2: Enter Record Setup to set network video parameters like resolution, frame rate etc.
Step 3: Open IE on a computer on the same network. Input the IP address of the DVR in IE
address bar and press enter.
Step 4: IE will download ActiveX component automatically. Enter the username and password
in the subsequent window

Notice: If HTTP port is not 80, other number instead, need add the port number after
IP address. For example, set HTTP port as 82, need input IP address like
192.168.0.25:82.
User name and password here are the same with that used on the DVR. The default
username and password is admin and 123456.

7.1.2 On WAN
There are two ways for the DVR to connect to internet.
1. Connect the DVR to internet through router or virtual server
Step 1: Enter into the DVR’s Main MenuSetupNetwork interface to input IP address,
Subnet Mask, etc. If using DHCP, please enable DHCP in both the DVR and router.
Step 2: Forward IP address and port number in Virtual Server setup of the router or virtual
server. Configure the firewall to allow accessing the DVR. (If the user has enabled the UPnP
function in both the DVR and router, he can skip this step.)
Step 3: If users want to utilize dynamic domain name, please apply for a domain name in a
DNS server supported by the DVR or router. Then add to the DVR.
Step 4: Open IE browser, input IP address, or dynamic domain name and enter. If HTTP port
is not 80, add the port number after IP address or domain name.
Step 5: IE will download ActiveX automatically. Then a window pops up and asks for user
name and password. Input name and password correctly, and enter to view.

Note: If you cannot download and install ActiveX, please refer to FAQ Q8.

44
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

2. Connect the DVR to internet directly


Step 1: Enter into the DVR’s Main MenuSetupNetwork interface to enable PPPoE and
then input user name and password received from your ISP. Next, click ‘Apply’. The DVR
will connect to the server and would give a confirmation message.
Step 2: When accessing the remote interface of DVR, user can input WAN IP to access
directly (user can enter into Main menuInformationNetwork interface to check IP
address). The browser will download Active X control.
Step 3: The following setting steps are as the same as Step 4 and Step 5 in Point 1.

7.2 Remote Surveillance through Apple PC

Note: Because the current plug-in version of client end just only supports 32-bit mode,
so the safari browser shall start 32-bit mode. If the browser is the earlier MACOS
version, the default setting is 32-bit mode and the setting can be skipped.

The setting steps are as follows:


Step 1: Right click safari icon and select “Show in Finder”.
Step 2: Select ApplicationsRight click “Safari. App”Select “Get Info”.

Step 3: Select “Open in 32- bit mode”.

7.2.1 On LAN
Step 1: After starting Apple computer, click Apple icon. The following window will pop up.
Please select “System Preferences” “Internet &Wireless” “Network”.

45
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 2: Go into Network interface and then click “Ethernet Connected” to check the internet
connection of Apple PC.

Step 3: After acquiring the IP address, Subnet Mask and so on, please enter into the DVR’s
Main MenuSetupNetwork interface to manually input IP address, Subnet Mask and
Gateway according to the configuration of PC. The network segment should be the same as
the PC. If using DHCP, please enable DHCP in the DVR and router.
Step 4: After the above information is completed, you can enter LAN IP and http port in the
Safari browser. For example: input http://192.168.1.100:81(here 192.168.1.100 is LAN IP of
DVR, 81 is the http port of DVR), and click “ ”button. Then the browser will download
Active X control as shown below:

Step 5: Click icon and then select the Active X control, the welcome interface will be
shown. Click “Continue” “Install” button,the following window will pop up:

Input the name and password of Apple PC and then click “OK” to install this Active X control.
Step 6: After finishing installing the Active X control, please quit from the Safari browser.
Right click Safari icon on the desktop and then select “Quit” button to quit the browser. Then
restart Safari browser. Input the IP address and http port to enter into the login interface of
DVR.

46
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

7.2.2 On WAN
There are also two ways for DVR to connect to Internet.
1. Connect the DVR to internet through router or virtual server
Step 1: The network setups are the same as step one to step four of point 1 on WAN of IE
remote surveillance.
Step 2: Enter WAN IP and http port in the Safari browser to install the Active control. The
concrete steps are the same as step 5 and 6 of Chapter 7.2.1.

2. Connect the DVR to internet directly.


Step 1: The network setups are the same as step one of point 2 on WAN of IE remote
surveillance.
Step 2: Enter WAN IP and http port in the Safari browser to install the Active control. The
concrete steps are the same as step 5 and 6 of Chapter 7.2.1.

7.3 The Remote Live Preview

Fig 7-1 Remote Live Preview Interface

1 Channel indicator 2 Screen display mode


3 Volume 4 Start recording
5 Snapping picture 6 Start IE record
7 Bidirectional talk 8 Playback
9 PTZ control 10 Master/sub stream status

Note: Click button to start recording. The record file will be saved in user’s PC.

47
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Screen display mode:


Click the icon beside the screen display mode to select channels.

Snap pictures
Click “Snap” icon to automatically capture pictures and save those pictures in the
computer. You can set up the save path for those picture in the Remote Preview interface 
Configuration Local configuration.

PTZ control
Please connect speed dome to the device via RS485 firstly, make sure the protocol of the
speed dome is supported by the device and set the relative parameters manually. User can
control the dome up, down, right, left or stop rotating on Control Center, adjust rotation speed,
Iris and zoom, focus on the dome, and set the presets, etc.
Buttons definition:

Buttons Description
to rotate the dome upwards. to rotate the dome diagonally
up-left. to rotate the dome diagonally up-right to rotate
the dome downwards. to rotate the dome diagonally
down-right to rotate the dome diagonally down-left to
rotate the dome towards left. to rotate the dome towards right
to stop rotating the dome.
Drag the scroll bar to adjust rotating speed of the dome.
'Iris' button. Click button near 'Iris' button to increase light
of the dome. Click button near 'Iris' button to decrease light
of the dome.
'Zoom' button. Click button near 'Zoom' button to zoom in
the locale picture of this camera. Click button near 'Zoom'
button to zoom out the locale picture of this camera.
'Focus' button. Click button near 'Focus' button to have long
focus. Click button near 'Focus' button to have short focus.
Go to the Preset

Select and do auto cruise


Track

Auto scan

Wiper button

Light button

Click the right mouse on the live interface. This will take you to a pull-down menu.

48
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Fig 7-2 Right Key Sub Menu

Stream: This DVR supports master stream and sub stream. Master stream has higher frame
rate, max 25FPS(PAL)/30 FPS(NTSC)for every channel, but it needs higher network
bandwidth simultaneously. Sub stream has low frame rate, max 6FPS (PAL)/7FPS(NTSC)
for every channel, it requires low network bandwidth. Therefore, you can select the stream
according to your bandwidth.
All to master/sub stream: Set all channel to master stream or sub stream.
Enable audio: Enable or disenable audio.
Full screen: The live preview picture will display with full screen and the tool bar will be hid.
Double click left mouse or click right mouse to return.
Zoom in: Single channel large screen electronic amplification. Click the channel which needs
to be zoomed. Right click to select zoom in button to zoom in the image. Double click or right
click to exit.

7.4 Remote Playback & Backup


7.4.1 Remote Playback
Click button to go into record playback interface. Refer to Fig 7-3:
Select the record date and channels and double-click the file name in the record file list box.
Then you can play that file and preview the picture.

Fig 7-3 Play Record File Interface

49
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

This DVR supports remote time search, event search and file management.

By Time Search:
Step 1: Enter into SearchTime Search. Refer to Fig 7-4:
Step 2: The highlight date in the area② indicates recorded data. Select the date in area ② and
record channels in area③.
Step 3: Click “Search” button. The record data will be displayed in the data information list
box.
Step 4: Set the data playing time and display mode in the area① as required.
Step 5: Click “Play” button to playback. 8 CH DVR only supports single channel display.

Fig 7-4 Time Search Interface

Step 6: Click the relevant buttons in the interface for operation, like FF, pause, change channel
mode, etc. Refer to Fig 7-5:

Fig 7-5 Time Search Playback

By Event Search:

50
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Step 1: Enter into SearchEvent Search interface. Refer to Fig 7-6:


Step 2: Click the highlight date and select record channels.
Step 3: Checkmark the event type: motion and sensor.
Step 4: Click “Search” button.
Step 5: Double-click certain item to play.

Fig 7-6 Event Search Interface

File Management
Step 1: Enter into SearchFile Management interface. Refer to Fig 7-7:

Fig 7-7 File Management Interface

Step 2: Select highlighted date and channels.


Step 3: Click “Search” button to search the recorded files.

Lock: Select certain file item in the file list box and then click “Lock” button to lock this file
that ca not be deleted or overlaid.
Unlock: Select a locked file and then click “Unlock” button to unlock this file.
Delete: Select an unlock file and then click “Delete” button to delete this file from file list.

51
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

7.4.2 Remote Backup


Click Backup button to enter into backup interface. Please refer to Fig 7-8:

Fig 7-8 Remote Backup Interface

Step 1: Select channels, set the start and end time and then click “search’ button to display the
file information in the file list box.
Step 2: Select backup files and click “Browse” button to set the save path. Then click
“Backup” button to start backup. The backup files will be saved on user’s PC.

7.5 Remote System Configuration


You can do remote setup of the device which includes functions like basic configuration, live
configuration, record configuration, schedule configuration, alarm configuration, network
configuration, PTZ configuration and user configuration. You should select an option from the
menu list on the left and then setup the relative parameters. Only one user can do
configuration setup at a given point of time. Click Config tab to enter into the below interface
The sub menu list and the options in every menu are similar to that of the DVR. Please refer to
Chapter 4 Main Menu Setup Guide for more details.

Fig 7-9 Remote Menu Setup

52
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

7.6 Tools
Click on the tool’s tab to access the Disk Management tool. The user can view the status of
the hard drive(s), can view/change the read write properties and can also format the hard
drive(s).

7.7 Remote Management


The Info interface provides a web based interface to access the general information pertaining
to the DVR’s settings. The interface includes five submenus: System, Event, Log, Network
and Online users.

Note: There may be subtle differences with respect to functions of remote surveillance
between through IE and through Apple PC. Here we only take IE remote access for
example.

53
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Appendix A FAQ
Q1. Why the DVR doesn’t turn on after connecting to the power?
a. The power adapter could have gone bad. Please change a new power adapter.
b. The power from the adapter may be not enough for operating the DVR. Please use the
power adaptor supplied along with the DVR.
c. It could be a hardware problem.

Q2. There is not menu displayed and only has live image display.
a. Check whether the monitor is connected to the main video out and not the spot out. The
monitor might be connected to VGA port whereas the DVR may be set for output through
BNC or vice versa. Long press ESC key to toggle the output modes.

Q3. The DVR LED turns on, however there is no output.


a. The power from the adapter may be not enough for operating the DVR. Please use the
power adaptor supplied along with the DVR.
b. It could be a wiring issue. Please check the connection for the same.
c. Check the monitor settings.

Q4. Why are no images displayed on few or all channels of the DVR?
a. It could be a wiring issue. Please check the cable and the ports of the cameras and DVR.
b. The problem can also be related to cameras. Please check the same.
c. Please make sure that the channels are not programmed as hidden channels and check the
status from admin login.

Q5. The HDD cannot be found.


a. The power from the adapter may be not enough for operating the DVR. Please use the
power adaptor supplied along with the DVR.
b. It could be wiring issue. Please check the power and data cables of the HDD.
c. The HDD could have gone bad. Change a new one.

Q6. The DVR cannot record.


a. Make sure the HDD was formatted prior to use.
b. Maybe the user hasn’t enabled the record function or has done incorrect setup. Please
refer to Chapter 5.
c. Maybe HDD is full and thus the DVR is not able to record. Check HDD information
from Disk Management and if required, please enable the recycle function.
d. The HDD could have gone bad. Please change another one.

Q7. Mouse doesn’t work.


a. The mouse should be connected to the USB port at the rear side.

54
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

b. After connecting the mouse, allow the DVR to detect the mouse for seconds. If not detected,
try restarting the DVR.
c. The mouse may be incompatible. Please change a mouse.

Q8. ActiveX control cannot be downloaded.


a. IE browser blocks ActiveX. Please do setup as per the steps mentioned below.
Step1: Open IE browser. Click ToolsInternet Options.

Step 2: Select SecurityCustom Level. Refer to Fig 8-1


Step 3: Enable all the sub options under “ActiveX controls and plug-ins”. Refer to Fig 8-2
Then click Ok to finish setup.

b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or do the required settings.

Fig 8-1 Fig 8-2

Q9: DVR displays “please wait…”all the time.


a. HDD power cable and data cable may not be well connected. Please check the
connections for HDD.
b. It is also possible that the DVR was forced to stop because HDD has a bad sector and it
may have caused the system to halt. Check with a good known HDD or try formatting the
existing HDD.

55
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Q10: How to input password and digital numbers?


Click the password or the input box a small keyboard will pop up. Please select characters to
be input (the initial password is 123456), or you can use the digital keys on the front panel, or
the digital keys on the remote controller.

Q11: A hard disk is being identified as a new device however it was being used with
another DVR of same model. Should it be formatted prior use?
It is possible to migrate an HDD from one DVR to another provided that the DVRs are of the
same model and that the HDD being migrated would be used as the sole disk in the new DVR.
However in cases where the new DVR already contains a HDD, the migrated disk being
installed would have to be formatted. In general migrating disks from one DVR to another is
not recommended.

Q12: What is the minimum configuration required for remote monitoring?

PC Module Parameters
CPU Intel Celeron 2.4G
Motherboard Intel 845
HDD 80G
RAM 512M
VGA NVIDIA GeForce MX440/FX5200 ATIRADEON 7500/X300
OS Windows 2000(SP4 above) /Windows XP(SP2 above) /VISTA
DirectX 9.0

Q13: How to handle the situation that the codec Control is blocked when downloading in
the VISTA or Win7 system?
This problem can be fixed in two ways:
a. Enter Control PanelUser Account and Family Safety  User Account Control (refer to
the following figure) and click Turn User Account on or off. Cancel Use User Account
Control (UAC) to help protect your computer.

b. Right click IE browser (refer to the following figure) and select Run as administrator to
run browser.

56
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Q14. How to play the backup file?


Insert your USB device where the backup files are saved in the USB port of PC. If your files
are saved in DVR format, you must have already downloaded the backup player box before
doing backup. Then double click to open your USB disk to find your backup files and backup

player. Double click icon to install backup player. After you install it, open this
player and click “Open Path” button to open your backup file. Next, click play button to
play the backup file. Double click the image and then right click to enable audio. If you save
your backup files in AVI format, you can directly open your file by using the media player
which supports this format.

57
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Appendix B Calculate Recording Capacity


Users can calculate the size of hard disk according to the saving time and DVR recording
settings. The DVR uses fixed video bit rate. The below are the details at different settings.

Resolut Frame Rate Bit Rate Used


Video Quality
ion Totally(FPS) (kbps) Space(MB/h)
Highest 12M 5400
Higher 9M 4050

25(PAL)/ Medium 7M 3150


1080P
30(NTSC) Low 6M 2700
Lower 4M 1800
Lowest 1.5M 675

The calculation format is: Total Recording capacity =Used space per hour (MB/h)
(coverage rate of hard disk) × recording time (hour) × channel numbers
For instance, one customer uses NTSC cameras, set resolution to 1080P, video quality to
Lowest, frame rate to 30 fps for enabling total 4 channels. He wants the unit to record
continuously in a month. Below is the calculation:

Total Recoding capacity =675 (mb/h) X 24(hours/day) X30(days) X4(channels)= 1944000


(MB)≈1898(GB)

Therefore, customers just install two SATA HDDs with 1TB, it can almost record for one
month.

58
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Appendix C Compatible Devices


1. Compatible USB drive after test.

Brand Capacity
SSK 512MB, 1G, 2GB
Netac 4GB
Kingston 2GB
Aigo 2GB
Smatter vider 1GB
SanDisk 4GB

2. Compatible SATA CD/DVD writers after test

Brand Model
TECLAST GH22NP20/TL-22XD
BENQ DW220S-0K4
LITEON DH—20A6S01C
LITEON DH-20A4P02C
SAMSUNG TS-H653B

3. Compatible HDD list

Brand Capacity
Seagate Barracuda 80G/160G/250G/320G /1.5T/2TB/3TB
Seagate SV35.3 1T
Seagate Pipeline HD.2 500G
Maxtor Diamondmax 160G
HITACHI Deskstar 80G/160G
WD WD1600JS 160G
Samsung HD161HJ 160G

59
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Appendix D 4 CH Specifications
Compression format H.264 Main Profile
Video output CVBS×1, VGA×1, HDMI×1
Video Input SDI×4
HDMI/VGA Resolution 1080P/1280*1024/ 800*600
Record Resolution 1080P (1920*1080)
Display Frame Rate 100FPS (PAL), 120FPS (NTSC)
Record Frame Rate 100FPS (PAL), 120FPS (NTSC)
Audio Input RCA X4
Audio output RCA X1
Alarm Input NO or NC 4CH
Alarm output: 4CH
Record Mode Manual / Sensor /Timer / Motion detection
Simplex/Duplex/Triplex Pentaplex
Network Interface RJ45 (LAN, INTERNET)
PTZ control YES
RS485, USB2.0 x 2 (one for backup, another for
Communication interface
USB mouse)
Disk info SATA x 1+DVD-RW x 1 or SATA x 2
Remote controller YES
Power Supply DC12V
Temperature 0℃-50℃
Humidity 10%-90%

60
Downloaded from www.Manualslib.com manuals search engine
DVR User Manual

Appendix E 8 CH Specifications
Compression format H.264 Main Profile
Video output CVBS×1, VGA×1, HDMI×1
Video Input SDI×4
HDMI/VGA Resolution 1080P/1280*1024/1280*768/ 800*600
Record Resolution 1080P (1920*1080)
Display Frame Rate 200FPS (PAL), 240FPS (NTSC)
Record Frame Rate 200FPS (PAL), 240FPS (NTSC)
Audio Input RCA X4
Audio output RCA X1
Alarm Input NO or NC 8CH
Alarm output: 1CH
Record Mode Manual / Sensor /Timer / Motion detection
Simplex/Duplex/Triplex Pentaplex
Network Interface RJ45 (LAN, INTERNET)
PTZ control YES
RS485, USB2.0 x 2 (one for backup, another for
Communication interface
USB mouse)
Disk info SATA x 1+DVD-RW x 1 or SATA x 2
Remote controller YES
Power Supply DC12V
Temperature 0℃-50℃
Humidity 10%-90%

61
Downloaded from www.Manualslib.com manuals search engine
450011000460 A1

Downloaded from www.Manualslib.com manuals search engine

You might also like