Trim and Upholstery: General Body Interior Trim

Trim and Upholstery
GENERAL
BODY INTERIOR TRIM
SIDE OPENING ELEMENTS TRIM
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
REAR SHELVES
FRONT SEAT FRAMES AND SEAT RUNNERS
REAR SEAT FRAMES ANDSEAT RUNNERS
FRONT SEAT TRIM
REAR SEAT TRIM
SEAT FITTINGS
77 11 190 895 NOVEMBER 1996 Edition Anglaise
"The repair methods given by the manufacturer in this document are based on the All copyrights reserved by Renault.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The methods may be modified as a result of changes by the manufacturer in the reference numbering system is forbidden without the prior written authority of
production of the various component units and accessories from which his vehicles Renault.
are constructed".
C Renault S.A. 1996

EXPLODED VIEW
PRC70.3
Trim
Contents
Pages Pages
70 GENERAL 73 TRIM FOR OPENING ELEMENTS

(OTHER THAN SIDE)
A Tooling and products 70-1
A Bonnet trim 73-1
B Tailgate trim 73-1
C Hood exterior trim (cabriolet) 73-2
D Padding (cabriolet) 73-7
71 BODY INTERNAL TRIM E Hood interior trim (cabriolet) 73-9
F Changing the hood bonded rear
A Front and rear door handles 71-1 73-13
screen (cabriolet)
B Interior trim fastenings on body side 71-2 G Changing the hood rear screen
C Centre pillar upper trim 71-3 73-20
secured by zip fastener (cabriolet)
D Front, centre and rear pillar lower
trim 71-4
E Front pillar upper trim 71-5
F Rear quarter panel trim 71-5
F Rear section lower trim (saloon) 71-6
F Rear quarter panel trim (cabriolet) 71-7
G Sill Panel - Seat belts 71-8
74 REAR SHELVES
A Side shelf 74-1

B Side shelf (utility version) 74-2
C Shelf trim (saloon) 74-3
72 SIDE OPENING ELEMENTS

TRIM 75 FRONT SEAT FRAMES AND
SEAT RUNNERS
A Door storage compartment 72-1
B Front door trim 72-2 75-1
A Complete seat
B Front door trim (phase II) 72-3 75-3
B Seat frame
B Front door trim (cabriolet) 72-5 75-4
C Seat runners
C Rear door trim 72-6 75-5
D Seatback frame
Contents (cont.)
Pages
76 REAR SEAT FRAMES AND

SEAT RUNNERS
A Complete seatback 76-1

B Seatback frame 76-1
77 FRONT SEAT TRIM
A Seat trim 77-1

B Seatback trim 77-3
78 REAR SEAT TRIM
A Rear bench seat frame 78-1

B Seat trim 78-2
B Seat trim (cabriolet) 78-3
C Seatback trim 78-4
C Seatback trim (cabriolet) 78-5
79 SEAT FITTINGS
A Head restraint trim 79-1

B Ski flaps (cabriolet) 79-2
B Rear head restraints (cabriolet) 79-2
GENERAL
D 53
CABRIOLET
Tooling and products 70 A
94791S
1 - Stapler tool Type : NAUDER*

and stainless steel clips
2 - Rivets Part number :

77 03 072 280
3 - Neoprene adhesive
4 - Brush
5 - Seal Part number:
* NAUDER :
Please contact your local After Sales Head Office

for details.
70-1
BODY INTERIOR TRIM
Front and rear door handles 71 A
92260R
REMOVAL
Insert a flat screwdriver in hole (2) in the upper

section, so that the first part of the handle can be
levered away and unhooked.
92261R
The handle is held by two screws (3).
71-1
BODY INTERIOR TRIM
Interior trim fastenings on body side 71 B
PRF7101
90230R1 90231R
(A) Snap fastening (C) Snap fastening
NOTE : If the dashboard is in place there is a risk of fastenings (A) ), (B), (C) and (D) breaking on removal. For
reasons of quality, it is preferable to change them, even if they can be re-used.
71-2
BODY INTERNALIOR TRIM
Centre pillar upper trim 71 C
REMOVING THE UPPER TRIM (1)
Unpick the upper section then free the seals by

pulling it away.
92339G
Remove:
- the seat belt mounting from the centre pillar, 92340R
- the seat belt height adjustment pushrod
(component in two sections). Remove the sliding cover from the adjustable
mounting.
71-3
BODY INTERIOR TRIM
Front, centre and rear pillar lower trim 71 D
PRF7102
Remove:
- the upper trim from the centre pillar (1) see section 71 B
- the mounting screws,
- the lower seat belt mounting.
By hand, free the rear part of the trim from the surrounding seal and remove clips (B).
Proceed in the same way for the front part of the trim.
Take out the trim through the rear door aperture.
71-4
BODY INTERIOR TRIM
Front pillar upper trim 71 E
Remove:
- the upper trim (1) from the centre pillar,
- the mounting screw,
- unpick the trim by pulling section (F) straight
downwards then backwards.
PRF7103
Rear quarter panel trim 71 F

Remove (see exploded view in section 71 B) :
- trims (1), (2), (6) and (7) ,
- the seal from the luggage compartment aper-
ture frame,
- the side shelf which is held by 5 screws,
- the two upper screws from the quarter panel
trim.
Unpick the trim (2 clips (C)) then remove the trim,

starting at the door seal end.
PRF7104
71-5
BODY INTERIOR TRIM
L 53
SALOON
Rear section interior trim 71 F
PRF7105
Remove in the following order:

1-2-3
71-6
BODY INTERNAL TRIM
D 53
CABRIOLET
Rear quarter panel trim 71 F
PRF7106
REMOVAL
94810R 94811R
Open the hood and tilt the rear seat. Remove nut (A) and unclip the fir tree type clips.
Remove the lower seat belt mounting and the Detach the trim from the rubbing strip.
hood opening handle.
71-7
BODY INTERIOR TRIM
S 53
UTILITY VERSION
Sill panel - Seat belts 71 G
PRJ4020
SILL PANEL
Fit the two lower sill panel trims (1) which serve as a storage compartment in the bottom of the side panel
trim.
REAR SEAT BELTS
Unclip:
- the trim between the left and right hand rear quarter panels,
- the rear quarter panel trims starting at the quarter light side and remove the seat belt blanking piece.
Fit the rear seat belt retractor in the rear quarter panel.
Route the belt and the guide through the opening in the rear quarter panel trim, then clip the guide to the
trim.
Reclip the panel trim and the centre trim.
Secure:
- The end of the seat belt to the sill panel trim at (4),
- the two seat belt stalks (5) to the floor panel after first removing the mastic from the mountings.
71-8
Door storage compartment 72 A
HIGH SPECIFICATION MODEL TYPE STORAGE BASIC MODEL TYPE STORAGE COMPARTMENT
COMPARTMENT
92262R 92263R
Remove: Remove the two screws (5) and free the storage
- the speaker grille by unscrewing it 1/4 of a compartment from the lower snap fastenings (7),
turn, by pushing it upwards.
- the speaker which is held by 4 screws,
- the 4 screws holding the speaker mounting,
- the mounting (6) and free the storage
compartment from the lower snap fastenings
(7), by pushing it upwards.
Disconnect the electric switch feed (8).
There is a leaktight rivet (9) holding the lower

snap fastening in place (component stays on the
door).
72-1
Front door trim 72 B
Remove:
- the internal opening control,
- the internal door handle,
- the rear view mirror base cover,
- the door storage compartment,
- the window winder.
92264R
(1) pressure stud

(2) clip on door
Remove the trim.
NOTE : the trim is clipped in place (1) and sealed

by mastic.
To remove it, the trim must be unpicked and uns-

tuck gradually (use a saw blade to cut the mastic)
then free it from the upper rubbing strip.
NOTE: when changing a door or the trim, trim

sealing mastic part number 77 01 421 049 must be
reapplied (see Technical Note N.T. 219 "DOOR
TRIM SEALING MASTIC").
72-2
X 53
PHASE II
95859-1S
REMOVAL
PRF7201 95859S
Unclip the rear view mirror mountings cover. Remove the pulling handle cover.
Disconnect the various switches.
72-3
X 53
PHASE II
PRF7202
Remove:
- the pulling handle,
- the loud speaker grille and storage compart-
ment,
- the internal handle.
For all removal-refitting operations, the door trim

seal must be changed.
72-4
D 53
CABRIOLET
Door trim 72 B
PRF7203
94792R
Remove:
- the rear view mirror internal cover (1),
- the internal handle (2),
- the internal opening handle (3),
- the speaker grille(4),
- the storage compartment(5).
Disconnect the rear view mirror harness (left hand

side).
72-5
Rear door 72 C
Remove:
- the internal opening control,
- the internal door handle,
- the ashtray,
- the window winder.
92265R
(1) pressure stud

(2) clip on door
Remove the trim.
NOTE : the trim is clipped in place (1) and sealed

by mastic.
To remove it, the trim must be unpicked and uns-

tuck gradually (use a saw blade to cut the mastic)
then free it from the upper rubbing strip.
NOTE: when changing a door or the trim, trim

sealing mastic part number 77 01 421 049 must be
reapplied (see "BODYWORK REPAIRS" poster).
72-6
Bonnet trim 73 A
PRF7301
Tailgate trim 73 B
PRF7302
Remove the two screws (1) and two hooks (2).
Unclip the trim.
73-1
D 53
CABRIOLET
Hood exterior trim 73 C
The operations described below must be carried out on both the left hand and right hand sides.
Any incorrect operation of the hood triggers an alarm. The order of operations must be followed.
PRF7303
Opening the hood
Fold the sun visors forwards. Lift the rear of the hood.
Open the front locks without folding back the Remove the safety device and open the hood
hood. compartment.
Operate the unlocking handle (this opens the rear Fold the rear section of the hood back into the
hood locks and the hood compartment). compartment.
73-2
D 53
CABRIOLET
After opening the hood
Removal
94787S
Remove the front angle piece and the two corner Remove the plastic clips.
segments. Free the two sections of material which corre-
spond to the front section.
Remove the seals from the front sections by sli-

ding them. 94762
Remove their slides (6 torx screws).
Remove the rear seals and slides.
Remove the four plastic clips.
73-3
D 53
CABRIOLET
Free the two corresponding pieces of material. At the front, remove the tensioning cable rivet
and remove the cable from the trim.
94971S
Undo the trim side mountings. (Quarter panels).

Lift the rear of the hood and remove the hood
frame rubber seal.
73-4
D 53
CABRIOLET
94788S
Free the rear screen tensioning material and re-

move the external hood trim.
Remove the rivets at the rear ends and at the

front of the rear pillar.
Remove the formed section of the rear part of the

hood.
73-5
D 53
CABRIOLET
Refitting
Start at the rear.

Clip the rear section taking care to centre the 94788S
hood (it is marked).
Route the tensioning cable and secure it.
Fold the hood forwards.
Stick the rear screen stiffener.
Refit the rubber seal.
Tilt the hood towards the rear and stick the front Close the hood completely and stick the side sec-
section. tions. Ensure that there are no creases.
Drill the holes in the trim and refit the plastic clips. Refit the small side tensioning straps.
Re-secure the front angle piece and the side seg-
ments.
73-6
D 53
CABRIOLET
Padding 73 D
PRF7304
Removal:
After removing the external trim, remove the ri- Remove the adhesive tape from the front section.
vets from the rear section and the stainless steel Unstick the front section.
clips.
73-7
D 53
CABRIOLET
Padding 73 D
Refitting:
Centre the padding on the hood. Stick the front section of the padding.
Refit the two side rivets (on the roof arch).
Clip the padding using suitable equipment (page

70-1) ensuring that there are no creases. 94789R
NOTE : The clips must be stainless steel and pres- Apply adhesive tape (Tésaband type).
sed in completely to prevent the external trim
from being marked.
73-8
D 53
CABRIOLET
Hood interior trim 73 E
PRF7305
Removal:
Remove the external trim and the padding. Carefully unstick the front section of the trim.
Undo the velcro.
Remove the rear quarter panel padding clips.
73-9
D 53
CABRIOLET
94790R
Carefully remove the tensioning strap rivets on the roof arches.
Remove the rear side rivets and the plastic pins, Carefully unstick the strips holding the trim on
then free the trim from the rear frame. the roof arches.
73-10
D 53
CABRIOLET
Refitting:
With the hood open: Stick the trim to the roof arches and secure the
Start to stick the front section centring the trim. tensioning straps (rivets).
Stick without forming any creases.
Temporarily fit the centre angle piece in order to
hold the front section.
94789
Position the hood frame forwards. Rivet the trim to the main roof arch (rear side).
Re-secure the rear sections of the tensioning Stick the trim to the rear hood frame and
straps to the main roof arch (clips). re- secure the velcro fasteners.
Tension and stick the rear section of the trim on
the roof roll-over bar and clip.
Check the tension of the trim.
73-11
D 53
CABRIOLET
- Secure the side rivets to the internal surface.

- Secure the plastic pins to the rear roof arch.
73-12
D 53
CABRIOLET
Changing the hood bonded rear screen 73 F
98629R
Description of kit Part Number 77 01 204 801
1 - Fitting template, with double sided adhesive

strips
2 - Marking template
3 - Rear screen
4 - Brushes (large and small)
5 - Double sided adhesive tape
6 - Smoothing tool
7 - AGS adhesive Part Number 77 01 040 979 (to

be ordered separately) (Single use consuma-
ble. It is essential that only this type of adhe-
sive is used).
98607S
Cut the centre section of the surround.

Clean the edge of the material with a brush.
73-13
D 53
CABRIOLET
98608S 98610S
Stick the adhesive tape to the edge of the mate- Carefully cut (edge) the material along the edge
rial. of the adhesive strip using scissors (FACOM type).
ATTENTION: the adhesive tape serves as a refe- Detach the remaining sections of the old rear
rence point for the dimensions of the new rear screen.
screen.
98609S 98611R
Make an initial cut of the rear screen leaving a Open the hood compartment cover.
strip of ≈ 20 mm.
Remove rivet (A).
Undo the retaining strip mountings (B).
73-14
D 53
CABRIOLET
98612R 98614R
Remove seal (C) and section (D) from the hood Fit fitting template (1), to the top of the hood to
frame. serve as a work plan.
Undo the adhesive strip protectors.
Turn the hood material over at the rear and fit
the rear screen cut-out onto the template starting
with the centre of the upper section and then the
lower section (marks, notches).
98613S 98615R
Unstick the rear screen tensioning band. Distribute the material evenly and secure it using
the template adhesive strips.
73-15
D 53
CABRIOLET
98616R
Fit the marking template (2) over fitting template

(1).
Using a ball point pen, mark the outline and ex-
ternal markers (notches) of template 2.
Remove template 2.
98617R
Apply an even layer of adhesive (using the large

brush) to the marked section of the hood mate-
rial.
73-16
D 53
CABRIOLET
98629-1R
NOTE: the strip of material has positioning

notches (B).
Also apply an even layer of adhesive to the strips

of material and the rear screen sealing strips
(using the small brush).
ATTENTION: It is essential to wait until the adhe-

sive becomes transparent before carrying out any
work (wait 15 to 30 minutes depending on the
ambient temperature).
Any stains or excess adhesive can be removed

(scratched off by hand) once the adhesive is dry.
Free the hood material from template 1.

Turn the template over and refit it on the hood.
73-17
D 53
CABRIOLET
98618R 94788S
Fit and stick the rear screen in line with the marks Stick the rear screen tensioning strip (Neoprene
(outline and notches) (two operators are required adhesive 3 M 8150).
to do this).
Fit seal (C).
Start at the centre of the upper section of the
hood. Lock the hood.
Rub the rear screen strip of material using the

smoothing tool in order to prevent creases from
forming.
Fit section (D) and rivet it to the hood frame.
Fit the mountings for retaining strips (B).
73-18
D 53
CABRIOLET
98606S
Protect the rear screen again (with cardboard and

lightweight felt to avoid damaging the rear
screen) and using the smoothing tool, lift the sec-
tion and fold it back on the material.
Rub the material firmly along the formed section.
NOTE: A second operator is required to exert a

counter pressure from the inside.
Remove the protectors.
IMPORTANT: Wait 72 hours before folding the

hood.
73-19
D 53
CABRIOLET TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Changing the hood rear screen secured by zip fastener 73 G
99563
Parts required: Description of operation :
REMOVAL
A kit Part Number: 77 01 041 838
1 - Clip and safety connection
2 - Slider
3 - Adhesive sealing strip
4 - Smoothing tool
Before carrying out any work, park the vehicle in

an area where there is an ambient temperature
of approximately 20°C.
Lower the side windows.
Unlock the hood.
Protect the rear section of the vehicle.

99564
Using the smoothing tool, lift the formed section

bead (A). Over a length of approximately 100 mm
at the lower section and at the centre of the
screen, pull back the edge of the hood material
(B).
73-20
D 53
99565 99567
From inside the vehicle, open the four claws of the Exert a slight pressure to the edge of the rear
safety clip of the zip fastener by twisting them. screen towards the inside to free it from the hood.
Take care not to damage the clip. NOTE: remove any remnants of the sealing strip.
Remove the safety clip connection.
Remove the safety clip.
99566
From inside the vehicle and using the smoothing

tool, open the zip fastener.
73-21
D 53
99617 99568
Protect the new rear screen. Close the zip fastener slowly. The operator out-
side the vehicle must hold the start of the zip fas-
First insert the slider on the rear screen transpa- tener to prevent it from opening.
rent mounting (slider tab facing towards the in-
side of the vehicle). Remove the slider.
From outside the vehicle, hold the rear screen in

position (a second person is required).
From inside the vehicle, insert the other part of

the zip fastener in the slider so that the two sides
are in line.
ATTENTION: the positioning operation is very im-

portant (risk of creasing the rear screen).
99569
Fit the safety clip and its connection.
Twist the claws (an external counter force is neces-

sary to correctly twist the claws).
Close the hood without locking it.
73-22
D 53
99570 98606S
Stick the sealing strip against the formed section Using the smoothing tool, lift the formed section
bead. and fold it back over the material.
Protect the rear screen with the cardboard on the Rub the material along the formed section firmly.
lightweight felt side.
NOTE: Exert a counter force from inside.
Lock the hood.
Remove the protectors.
IMPORTANT: Wait 24 hours before folding the

hood.
73-23
REAR SHELVES
Side shelf 74 A
92461R1
Remove the centre shelf.
Disconnect the speaker.
Remove the five mounting screws (1).
74-1
REAR SHELVES
S 53
UTILITY VERSION
Side shelves 74 B
FITTING SIDE SHELVES
PRJ4021
Remove the rear wheel arch side trims.
Fit the side shelf lower mounting clips.
On the left hand side, cut the wheel arch side trim
at the wheelbrace clip locations.
Fit the 3 wheelbrace mounting clips (2).
Fit the two side shelves : 5 screws (1).
On the right hand side, fit the upper and lower

jack supports using pop rivets.
Fit the rear centre shelf in the location of the side

shelves and secure the retaining cords in the ope-
nings in the rear luggage compartment trim.
92461R
74-2
REAR SHELVES
L 53
SALOON
Side shelves 74 C
Partially remove the two lower rear pillar trims.
PRF7401
REMOVAL
PRF7404
Remove the rear quarter panel trims.
PRF7402
Partially remove the two roof panel trims (A) (on

the rear door upper section).
93138S
PRF7403
74-3
Complete seat 75 A
REMOVAL
93220
92464R - front mounting screw (3) and remove the

trim,
Remove:
- mounting screw (1) from the seat runner side
trim and remove the trim by pulling it for-
wards.
94262R
- mounting screws (4) securing the seat frame

to the seat runner.
93219S
- rear mounting screw (2) securing the centre

trim (on the handbrake side),
75-1
Complete seat 75 A
92463R
On the opposite side, remove the three screws (5)

and the seat.
75-2
Seat frame 75 B
92465 92466
The seat frame is secured to the subframe by four and by one screw on the opposite side.
Torx screws.
92467
The seatback frame is secured to the seat squab

frame by three nuts, on the seat adjusting knob
side.
75-3
Seat runners 75 C
REMOVAL
92460R
The seat runners are secured from underneath

the vehicle by means of four nuts (1).
75-4
Seatback frame 75 D
LUMBAR ADJUSTING MECHANISM
REMOVAL
92475
To remove the plastic guide, open the two half-

shells by unclipping them.
92473
After first stripping the seatback, adjust the me-

chanism to the released position.
Cut the rivet securing the control (indicated by the

arrow on the photograph). REFITTING
92474 92476
Using a pair of pliers, remove the cable stop so Refit the assembly, finishing with the assembly of
that the cable can be passed through the frame. the two cables on the central spring.
75-5
REAR SEAT FRAMES AND SEAT RUNNERS
Complete seatback 76 A
REMOVAL
92427S
Remove the seatback assemblies (2/3 - 1/3) by lif-

ting the levers at the ends of the hinges.
Seatback frame 76 B
REMOVING THE CATCH
92483
92486
Using a screwdriver, remove the handle as shown.
Partially strip the seatback and remove the two

screws securing the catch.
76-1
FRONT SEAT TRIM
Seat trim 77 A
92468 92470
Using a screwdriver, remove the centre clip from

the seatback adjusting knob and pull the knob to
remove it.
92469 93221
Turn the seat over and unclip the front and rear Unclip the clips holding the two side sections of
plastic angle pieces from the trim. the trim.
77-1
FRONT SEAT TRIM
Seat trim 77 A
92471
From inside the frame, unclip the plastic hooks

holding the rear corner angle sections of the trim.
93222
To separate the trim from the foam, cut the clips

securing the trim to the linkage rods concealed in
the foam.
93221-1
Cut the clips which secure the trim linkage rods to

the frame.
Remove the foam - trim assembly.
77-2
FRONT SEAT TRIM
Seatback trim 77 B
92477 92223
If the seat is fitted with seatback adjustment, re- Partially lift the trim and cut the clips securing the
move the centre clip from the adjusting knob back of it to the frame.
using a screwdriver and pull the knob to remove
it.
92478 92224
Behind the seat, cut the two clips securing the two Lift the trim further and cut the clips located at
linkage rods together. each end of the piece of card used to stretch the
material. Pass the card through the foam.
Unclip the rods from the frame at their ends.
77-3
FRONT SEAT TRIM
Seatback trim 77 B
92480
Using a screwdriver, unclip the two guides from

the head restraint rods.
93225
Cut the two clips securing the upper rod linkage

to the frame and remove the trim.
77-4
REAR SEAT TRIM
S 53
UTILITY VERSION
Rear bench seat frame 78 A
PRJ4022
PREPARING THE SEATBACK
Fit clip (1) and rod (2) connecting the two catches.
Fit the two catches (3) to the frame.
The handles (4) are fitted after fitting the trim to the seatback.
PREPARING THE SEAT
Fit:
- the handle guide (5),
- the manoeuvring handle (6),
- the two hinge supports (7) are fitted to the seat frame after fitting the trim.
PREPARATION ON THE VEHICLE
Fit:
to the wheel arch inner lining :

- the two seatback hinge pins (8),
- the two seatback locking pins (9).
to the floor panel :

- the two seat stops (10).
78-1
REAR SEAT TRIM
Seat trim 78 B
92487 92489
After removing the bench seat, unpick the edge

of the trim from the metal frame.
92490
92488
Pass the two sheets of card used to stretch the fa-

bric through the foam.
Turn the seat over.
Cut the clips securing the trim to the linkage rods

concealed in the foam.
92491
78-2
REAR SEAT TRIM
D 53
CABRIOLET
Seat trim 78 B
PRF7801
94821
After removing the bench seat, carefully unpick

the edge of the trim. 94822
Remove the foam - trim assembly. Remove the clips and pass the card through the
foam to separate the trim.
78-3
REAR SEAT TRIM
Seatback trim 78 C
REMOVAL
92482 92485
Unpick the lower corner of the trim held by three Pass the card used to stretch the fabric through
fir tree type clips. the foam.
92484
Unpick the edge of the trim secured to the metal

frame.
Remove the foam - trim assembly.
78-4
REAR SEAT TRIM
D 53
CABRIOLET
Seatback trim 78 C
PRF7802
94823
Carefully unpick the edge of the trim.

92427S
Remove the seatback.
Lift the levers located at the ends of the hinges.
78-5
REAR SEAT TRIM
D 53
CABRIOLET
Seatback trim 78 C
94824 94826
Separate the strips of velcro and unclip the trim Unclip the edge of the ski cover carefully.
from around the ski flap.
Refitting:
For refitting, the ski flap must be removed

(4 rivets).
First refit:
The ski cover.
Re-secure the flap.
Clip the trim around the plate.
Finish off by hooking and clipping the other sec-

94825 tions of the trim.
Remove the clips and pass the pieces of card

through the foam.
Remove the circular clips retaining the seat belt

buckles.
Detach the trim from the foam.
78-6
SEAT FITTINGS
Head restraint trim 79 A
PRF7901
94827 94828
After removing the head restraint, unclip the trim

and detach the foam - trim assembly from the
frame.
79-1
SEAT FITTINGS
D 53
CABRIOLET
Ski flap 79 B
94812R
The ski flap is removed by removing rivets (A).
D 53
CABRIOLET
Rear head restraint 79 C
94827
REMOVAL:
Remove the screws and tilt the head restraint in

order to remove the retaining lugs. 94829
79-2

Trim and Upholstery: General Body Interior Trim

Uploaded by

Copyright:

Available Formats

Trim and Upholstery: General Body Interior Trim

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Trim and Upholstery: General Body Interior Trim

Uploaded by

Copyright:

Available Formats

Trim and Upholstery

BODY INTERIOR TRIM

SIDE OPENING ELEMENTS TRIM

TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)

FRONT SEAT FRAMES AND SEAT RUNNERS

REAR SEAT FRAMES ANDSEAT RUNNERS

FRONT SEAT TRIM

REAR SEAT TRIM

77 11 190 895 NOVEMBER 1996 Edition Anglaise

C Renault S.A. 1996

70 GENERAL 73 TRIM FOR OPENING ELEMENTS

A Side shelf 74-1

72 SIDE OPENING ELEMENTS

76 REAR SEAT FRAMES AND

A Complete seatback 76-1

77 FRONT SEAT TRIM

A Seat trim 77-1

78 REAR SEAT TRIM

A Rear bench seat frame 78-1

A Head restraint trim 79-1

1 - Stapler tool Type : NAUDER*

2 - Rivets Part number :

5 - Seal Part number:

Please contact your local After Sales Head Office

Insert a flat screwdriver in hole (2) in the upper

The handle is held by two screws (3).

(A) Snap fastening (C) Snap fastening

Unpick the upper section then free the seals by

Take out the trim through the rear door aperture.

Rear quarter panel trim 71 F

Unpick the trim (2 clips (C)) then remove the trim,

Remove in the following order:

REAR SEAT BELTS

Reclip the panel trim and the centre trim.

Disconnect the electric switch feed (8).

There is a leaktight rivet (9) holding the lower

(1) pressure stud

Remove the trim.

NOTE : the trim is clipped in place (1) and sealed

To remove it, the trim must be unpicked and uns-

NOTE: when changing a door or the trim, trim

Disconnect the various switches.

For all removal-refitting operations, the door trim

Disconnect the rear view mirror harness (left hand

(1) pressure stud

Remove the trim.

NOTE : the trim is clipped in place (1) and sealed

To remove it, the trim must be unpicked and uns-

NOTE: when changing a door or the trim, trim

Remove the two screws (1) and two hooks (2).

Unclip the trim.

Opening the hood

Remove the seals from the front sections by sli-

Undo the trim side mountings. (Quarter panels).

Hood exterior trim 73 C

Free the rear screen tensioning material and re-

Remove the rivets at the rear ends and at the

Remove the formed section of the rear part of the

Start at the rear.