Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • TUBE, UNS S30400/S30403, SMLS, Annealed

    Uploaded by

    Tuấn Dương Quốc
    102 views2 pages
    This document specifies requirements for seamless 304/304L stainless steel tubing intended for use with Swagelok tube fittings. Key requirements include: - Tubing must meet ASTM standards for material composition and mechanical properties. - Tubing must undergo solution heat treatment, mechanical testing, and nondestructive testing. - Tubing must have specific dimensions, finishes, and be properly line marked and certified.

    Original Description:

    Original Title

    scs-00061

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document
    This document specifies requirements for seamless 304/304L stainless steel tubing intended for use with Swagelok tube fittings. Key requirements include: - Tubing must meet ASTM standards for material composition and mechanical properties. - Tubing must undergo solution heat treatment, mechanical testing, and nondestructive testing. - Tubing must have specific dimensions, finishes, and be properly line marked and certified.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as docx, pdf, or txt
    102 views2 pages

    TUBE, UNS S30400/S30403, SMLS, Annealed

    Uploaded by

    Tuấn Dương Quốc
    This document specifies requirements for seamless 304/304L stainless steel tubing intended for use with Swagelok tube fittings. Key requirements include: - Tubing must meet ASTM standards for material composition and mechanical properties. - Tubing must undergo solution heat treatment, mechanical testing, and nondestructive testing. - Tubing must have specific dimensions, finishes, and be properly line marked and certified.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as docx, pdf, or txt
    of 2

    SCS-00061

    TUBE, UNS S30400/S30403, SMLS, Rev. B


    ANNEALED DCN # 00197440
    DCN Date: Mar 13, 2020
    Page 1 of 2
    Printed copies are uncontrolled unless marked "CONTROLLED" in red.
    Uncontrolled copies must be verified as current before use.

    1.0 SCOPE
    This specification defines the minimum suggested ordering requirements for seamless 304/304L dual certified
    tubing intended for use with Swagelok tube fittings.

    2.0 REFERENCES (latest revisions at time of order apply)


    2.1. ASTM A213 / ASME SA213, Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler,
    Superheater, and Heat-Exchanger Tubes
    2.2. ASTM A262, Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
    2.3. ASTM A269, Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
    2.4. ASTM A632, Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-
    Diameter) for General Service.
    2.5. ASTM A1016, General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel
    Tubes

    3.0 GENERAL REQUIREMENTS


    3.1. UNS S30400/S30403 stainless steel tubing shall be supplied as average wall thickness ± 10%, and in
    accordance with the following:
     ASTM A213 / ASME SA213 (Ref. 2.1)
     ASTM A269 (Ref. 2.3)
     ASTM A1016 (Ref. 2.5)
     ASTM A632 (1/8 inch tubing and smaller, 3 mm tubing and smaller) (Ref. 2.4)
    3.2. Tubing shall be suitable for bending and flaring.
    3.3. Tubing shall be manufactured free of mercury contamination.

    4.0 CHEMICAL COMPOSITION


    4.1. Material shall meet the following chemical requirements for UNS S30400/S30403 listed in ASTM A213 /
    ASME SA213 (Ref. 2.1), ASTM A269 (Ref. 2.3), or ASTM A632 (Ref. 2.4).

    C 0.030 max. Mn 2.00 max. P 0.045 max


    S 0.005 – 0.015 Si 1.00 max. Cr 18.00 – 20.00
    Ni 8.00 – 11.00

    5.0 MECHANICAL PROPERTIES


    5.1. Tubing shall be solution heat treated to a minimum of 1900°F (1040°C) with water cooling or other rapid
    cooling.
    5.2. Tubing larger than 1/8 inch shall meet the mechanical properties requirements listed below for UNS
    S30400/S30403 listed in ASTM A213 (Ref. 2.1) or ASTM A269 (Ref. 2.3).
    5.3. 1/8 inch and smaller tubing shall meet the mechanical properties requirements listed below for UNS
    S30400/S30403 listed in ASTM A632 (Ref. 2.4).
     Tensile Strength, min 75 ksi [515 MPa]
     Yield Strength, min 30 ksi [205 MPa]
     Elongation in 2" or 50 mm, min 35%
     Hardness, max 90 HRB [200HV]

    6.0 INSPECTION AND TESTING REQUIREMENTS


    6.1. Chemical analysis shall be performed in accordance with ASTM A1016 (Ref. 2.5).
    6.2. Mechanical properties testing shall be performed in accordance with ASTM A1016 (Ref. 2.5) including:
    6.2.1 Tensile test, 1 sample for lots ≤ 50 tubes, 2 samples for lots > 50 tubes
    6.2.2 Flattening test, 1 sample per lot
    6.2.3 Flaring test, 1 sample per lot
    This document and information on it are the confidential property of the Swagelok Companies and are loaned to you for a limited purpose. Neither may be
    copied, exhibited, or furnished to others in any form without the written consent of a Swagelok Company.
    SCS-00061
    TUBE, UNS S30400/S30403, SMLS, Rev. B
    ANNEALED DCN # 00197440
    DCN Date: Mar 13, 2020
    Page 2 of 2
    Printed copies are uncontrolled unless marked "CONTROLLED" in red.
    Uncontrolled copies must be verified as current before use.

    6.2.4 Hardness test, 2 samples per lot


    6.3. Each tube shall be subjected to the Nondestructive Electric Test (eddy current) or the hydrostatic test in
    accordance with ASTM A1016 (Ref. 2.5).
    6.4. Tubing shall be capable of passing corrosion testing in accordance with ASTM A262 Practice E (Ref 2.2).

    7.0 FINISH
    7.1. Tubing shall be seamless, cold drawn or pilgered, fully annealed, and straightened (straightened not
    applicable to coiled tubing).
    7.2. All tubes shall have a uniformly polished OD (may not be applicable to coiled tubing) finish free of
    scratches. Selective grinding is not permitted.
    7.3. Tubes shall be pickled free of scale. When bright annealing is used, pickling is not necessary.
    7.4. Finished tubes shall have ends free of burrs and the inside surface shall be free of dirt, chips, oil, scale or
    corrosion.

    8.0 DIMENSIONS
    8.1. Tubing shall be either 20 feet or 6 meters in length, as specified on the purchase order and to the
    tolerances of ASTM A632 (ref. 2.4) and ASTM A1016 (ref. 2.5) listed in the table below.

    Size, O.D., in. Outside Diameter, in. Wall Thickness, % Cut Length, in.
    Up to 3/32, excl + 0.002 / - 0 ± 10 + 0.125 / - 0
    3/32 to 3/16, excl + 0.003 / - 0 ± 10 + 0.125 / - 0
    3/16 to 1, excl ± 0.005 ± 10 + 0.125 / - 0
    1 to 1 ½, incl ± 0.006 ± 10 + 0.125 / - 0
    Over 1 ½ to 2, excl ± 0.008 ± 10 + 0.125 / - 0
    2 to 2 ½, excl ± 0.010 ± 10 + 0.188 / - 0

    8.2. Ovality / Out-of-roundness shall not exceed 0.005 inches.


    8.3. Straightness of each tube shall not exceed 0.030 inches maximum curvature in any 3 foot span.

    9.0 MARKING
    9.1. Tubing shall be line marked in accordance with the requirements of ASTM A213 (Ref. 2.1) or ASTM A269
    (Ref. 2.3), and ASTM A1016 (Ref. 2.5), including the material specification and grade, condition, wall
    designation, outside diameter, wall thickness, (melt) heat number, and lot number.
    9.2. All tubing sizes shall be line marked, with the exception that tubing smaller than ¼” and 6mm in diameter
    may be tagged in lieu of line marking.
    9.3. Line mark manufacturer. Line mark country of origin if not made in the USA.

    10.0 CERTIFICATION
    A Certified Material Test Report from the tube manufacturer shall be furnished with each shipment with the
    following additional requirements:

    10.1. Chemical composition, both ladle and product analysis test results, in accordance with section 4.0.
    10.2. Tensile test results in accordance with sections 5.2 and 5.3.
    10.3. Flattening test results in accordance with section 6.2.2.
    10.4. Flaring test results in accordance with section 6.2.3.
    10.5. Hardness test results in accordance with section 6.2.4
    10.6. Results of eddy current or hydrostatic testing in accordance with section 6.3.
    10.7. Results of corrosion testing in accordance with section 6.4, if conducted.

    This document and information on it are the confidential property of the Swagelok Companies and are loaned to you for a limited purpose. Neither may be
    copied, exhibited, or furnished to others in any form without the written consent of a Swagelok Company.

    You might also like