Shower and Floor Gullies Channel Drain and Tile Drain: Section
Shower and Floor Gullies Channel Drain and Tile Drain: Section
Shower and Floor Gullies Channel Drain and Tile Drain: Section
31
General Information
Shower and Floor Gullies
■ McAlpine has responded to market conditions and customer demand by producing an extensive
range of gullies suitable for shower and wet floor areas
■ The comprehensive range of gullies is suitable for concrete and suspended timber floors finished
with sheet flooring, tiles or stone
■ Two-piece gullies enable the gully to be plumbed prior to installation of timber floors and wet room
floor formers
■ McAlpine gullies are ideal for domestic wet rooms, Lifetime Homes, disabled adaptations, student
accommodation, bathroom pods, hotels, hospitals, secure accommodation and sport and leisure
facilities
■ Manufactured in ABS to the highest quality, McAlpine gullies comply to EN 1253-2:2003
■ Flow rates of 48 litres per minute exceed the minimum requirement of EN 1253-2:2003 and are
variable dependent on the grating or cover plate used
■ Range of Trapped Shower Gullies (TSG) available with 50mm, 60mm and 75mm water seal,
Untrapped Shower Gullies (USG) for use with pumped waste and Valve Shower Gullies (VSG) for use
in floors where depth is restricted
■ Choice of horizontal or vertical outlet
■ All gullies have top access for easy cleaning
■ Choice of white plastic, polished stainless steel and chrome plated finishes for tiles, gratings,
clamp rings and cover plates
■ The Tile Drain is suitable for concrete and suspended timber floors finished with tiles or stone
■ Manufactured in grade 304 stainless steel
■ Choice of 150m square stainless steel designer tiles reversible to accommodate tiles up to 8mm
■ Frame height adjustable to suit tiles up to 16mm
Code TSG50T6SS
32
Assembly and Features of Trapped Gullies SECTION 2
Sheet Flooring 1 Code TSG1-WH
1 Choice of cover plates with or without securing
screws 2
2 Cover plate and dip tube assembly. Choice of
cover plate finishes available
75mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and 2" x
11/2" socket reducer. Overall height 130mm
With
securing TSG1-WH TSG1SS TSG1SS-SL-SC
screws
Without
securing TSG1WH-NSC - TSG1SS-SL-NSC
Gullies for use with Sheet Flooring
screws
50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 100mm
With
securing TSG50WH TSG50SS TSG50SS-SL-SC
screws
Without
securing TSG50WH-NSC - TSG50SS-SL-NSC
screws
Two-Piece Gully, 50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal
outlet, 2" swivel outlet fitting and 2" x 11/2" socket reducer. Overall height 100mm
With
securing TSG52WH TSG52SS TSG52SS-SL-SC
screws
Without
securing TSG52WH-NSC - TSG52SS-SL-NSC
screws
75mm Water Seal Trap with 110mm vertical outlet and 110mm x 2" BS EN 1329-1:2000
solvent spigot outlet. Overall height 130mm
With
securing TSG2WH TSG2SS TSG2SS-SL-SC
screws
34 Without
securing TSG2WH-NSC - TSG2SS-SL-NSC
screws
Gullies show white cover plates for illustrative purposes only. See page 52 for gully flow rates
SECTION 2
Trapped Gullies White Plastic Polished CP Brass Clamp
Clamp Ring and Stainless Steel Ring, CP
Choose the appropriate gully body Cover Plate Clamp Ring and Stainless Steel
and cover plate finish required Cover Plate Grated Cover
Plate
Gullies without securing screws
allow for easier access
50mm Water Seal Trap with 11/2" BS EN 1329-1:2000 solvent weld side inlet for the discharge
from a wash hand basin with a 110mm vertical outlet to fit 110mm pipe socket or vertical
11/2" solvent weld pipework. Overall height 130mm
With
securing TSG3-WH TSG3SS TSG3SS-SL-SC
screws
Without
Untrapped Gullies
Untrapped Gully with 22mm horizontal plain outlet for use with pumped waste.
Overall height 44.5mm
With
securing USG1WH USG1SS USG1SS-SL-SC
screws
Untrapped Gully with 2" BS EN 1329-1:2000 solvent weld vertical outlet and 2" x 11/2"
socket reducer. Overall height 70.5mm
With
securing USG2SS-SL-SC
USG2WH USG2SS
screws
With
securing
USG3WH USG3SS USG3SS-SL-SC 35
screws
Gullies show white cover plates for illustrative purposes only. See page 52 for gully flow rates
Gullies for use with Tiled or Stone Floors where a Waterproofing
Trapped Gullies 150mm Square 150mm Square 125mm
Polished White ABS Tile Diameter Polished
Choose the appropriate gully body Stainless Steel with removable Stainless Steel
and cover plate finish required Tile with Grid Grating with
removable Grid removable Grid
Gullies without securing screws
allow for easier access
75mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 130mm
With
Gullies for use with Tiled or Stone Floors
securing TSG1T6SS - -
screws
Without
securing TSG1-T150SS TSG1T6WH TSG1-R125SS
screws
50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 100mm
With
securing TSG50T6SS - -
screws
Without
securing TSG50-T150SS TSG50T6WH TSG50-R125SS
screws
Two-Piece Gully, 50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal
outlet, 2" swivel outlet fitting and 2" x 11/2" socket reducer. Overall height 100mm
With
securing TSG52T6SS - -
screws
Without
securing TSG52-T150SS TSG52T6WH TSG52-R125SS
screws
75mm Water Seal Trap with 110mm vertical outlet and 110mm x 2" BS EN 1329-1:2000
solvent spigot outlet. Overall height 130mm
With
securing TSG2T6SS - -
screws
Without
36
securing TSG2-T150SS TSG2T6WH TSG2-R125SS
screws
Gullies show square stainless steel cover plates for illustrative purposes only. All above gullies supplied
with white plastic clamp ring. See page 52 for gully flow rates
Membrane is required SECTION 2
Untrapped Gullies 150mm Square 150mm Square 125mm
Polished White ABS Tile Diameter Polished
Choose the appropriate gully body Stainless Steel with removable Stainless Steel
and cover plate finish required Tile with Grid Grating with
removable Grid removable Grid
Gullies without securing screws
allow for easier access
Untrapped Gully with 22mm horizontal plain outlet for use with pumped waste.
Overall height 44.5mm
With
securing USG1T6SS - -
Untrapped Gully with 2" BS EN 1329-1:2000 solvent weld vertical outlet and 2" x 11/2" socket
reducer. Overall height 70.5mm
With
securing USG2T6SS - -
screws
Without
securing USG2-T150SS - -
screws
37
Gullies show square stainless steel cover plates for illustrative purposes only.
See page 52 for gully flow rates
Two-Piece Gully and Gully with Non-Return Valve
■ Two-piece gullies have been specifically ■ The Valve Shower Gully (VSG) has been
designed for use with timber floors and floor developed to satisfy customer demand for a
formers and can be plumbed prior to the shallow gully suitable for installation in
installation of the floor or former. See pages floors where depth is restricted
34-40 for product range
Two-Piece Gully and Gully with Non-Return Valve
Code VSG1WH-NSC
38
Code TSG52T6SS
Gullies with Non-Return Valve for use where floor
depth is restricted SECTION 2
■ The Valve Shower Gully (VSG) has been developed to satisfy customer demand for a shallow gully
suitable for installation in floors where depth is restricted
■ The overall height of the VSG1 is only 75mm and the valve is a substitute for a regulatory water
seal trap which cannot be incorporated in a gully of this height
■ There are currently no regulations to cover the use of anything other than water seal traps in
domestic drainage systems. Although valves have been in existence for some time, it is advisable
to seek guidance from the local building control department prior to use
■ The valve acts as a non-return valve, the weight of the water discharge will open the valve and it
will reseal when the discharge has ceased thus prohibiting foul air from entering the dwelling
■ The valve eliminates the release of foul air due to back flow
■ The valve can be easily removed to facilitate easy cleaning of the gully
■ The VSG range has a minimum flow rate of 30 litres per minute when tested with a 15mm head
of water
Two-Piece Gully, White Plastic Clamp Ring with Cover Plate and
11/2" BS EN 1329-1:2000 solvent weld horizontal outlet.
Overall height 85mm
VSG1T6SS
39
Gullies without securing screws allow for easier access See page 52 for gully flow rates
Code VSG52T6SS
Flooring
■ Shower gullies with anti-ligature grating have been designed for use in secure accommodation
■ Grating is Home Office approved
■ All gullies supplied with security screwdriver bit to release anti-ligature grating
75mm Water Seal Trap 2" BS EN 1329-1:2000 solvent weld
horizontal outlet and 2" x 11/2" socket reducer. CP brass clamp
ring with polished stainless steel anti-ligature grating.
Overall height 130mm
Code TSG1-ANTI/LIG
Code TSG50-ANTI/LIG
Code TSG52-ANTI/LIG
75mm Water Seal Trap with 110m vertical outlet and 110mm x
2" BS EN 1329-1:2000 solvent weld reducer. CP brass clamp
ring with polished stainless steel anti-ligature grating.
Overall height 130mm
40 Code TSG2-ANTI/LIG
Top Access Shower Traps for use with Sheet Flooring, Tiled or Stone Floors
Tiled or Stone Floors SECTION 2
For Sheet Flooring
19mm Water Seal Trap with 11/2" universal compression outlet, white
plastic clamp ring and cover plate with securing screws.
Overall height 138mm
Code TSG1WH-STW1R
Code TSG1WHSTW295
Code TSG1WH-STW2R
Code TSG1T6SSSTW295
41
Code TSG1T6SS-STW2R
See page 52 for gully flow rates Do not pour drain cleaner down these products
Tiles and Gratings
150mm Square Polished Stainless Steel Tile with removable grid and
securing screws. Tile has ABS spigot adaptor for solvent welding to clamp
ring
Code FGTOP6SS
150mm Square Polished Stainless Steel Tile with removable grid. Tile
has a removable ABS spigot adaptor for solvent welding to clamp ring
leaving a rubber gasket to fit inside 110mm pipe
Code FGT150TOP
150mm Square White ABS Tile with removable grid. Tile has spigot
adaptor for solvent welding to clamp ring
Code MDTOP-WH
200mm Square White ABS Tile with removable grid. Tile has spigot
adaptor for solvent welding to clamp ring
Code MDTOP20-WH
125mm Diameter Polished Stainless Steel Grating with removable grid.
Grating has a removable ABS spigot adaptor for solvent welding to
clamp ring leaving a rubber gasket to fit inside 110mm pipe. Suitable
for stone shower bases
Code FGTR125TOP
air entering the building ■ Valve easily removed for cleaning and
■ The 150mm square tile can be fitted on a maintenance work
trapped or untrapped drain
150mm square stainless steel
tile with silicone non-return
valve and removable grid
including removable stainless
steel mesh filter
Code FGT150-SV-110
Code FGT150-SV-110S
Gullies suitable for Concrete Ground Floors where a
Waterproofing Membrane is not required SECTION 2
Trapped Gully Bodies
Multi-Drain - 60mm Water Seal Universal Trapped Floor Gully
manufactured in grey ABS with 2"/3" solvent weld horizontal outlet.
Height can be extended by solvent welding length of 110mm PVC pipe
between gully body and tile. Inlet connections are for solvent welding to
11/2" ABS/PVC pipe, internal fit or 2" ABS/PVC pipe, external fit.
Overall height 152mm
Code MD100-3
Code FD90-T6WH 43
20.5 -
85mm
25.5mm
44
Standard Channel Drain with brushed Standard Channel Drain with grid (brushed
finish cover plate finish)
Code CD600-B Code CD600-SQ
Code CD700-B Code CD700-SQ
Code CD800-B Code CD800-SQ
Code CD900-B Code CD900-SQ
Code CD1000-B Code CD1000-SQ
Code CD1200-B Code CD1200-SQ
20.5 -
Width of Channel Frame 51mm
85mm
25.5mm
Channel Drain for Tiled Floors
Slimline Channel Drain with brushed finish Slimline Channel Drain with polished finish
cover plate cover plate
Code CD600-O-B Code CD600-O-P
Code CD700-O-B Code CD700-O-P
Code CD800-O-B Code CD800-O-P
46 Code CD900-O-B Code CD900-O-P
Code CD1000-O-B Code CD1000-O-P
Code CD1200-O-B Code CD1200-O-P
Cover plates available separately on request Do not pour drain cleaner down these products
Tile Drain for Wet Floor Areas SECTION 2
■ Tiles suitable for 50mm water seal traps as
illustrated
■ Tiles supplied with brushed or polished
finish. All in grade 304 stainless steel
■ Tiles reversible to accommodate tiles up to
8mm
■ Tile frame dimension 150mm square
■ Frame height adjustable to suit tiles up to
16mm
■ Supplied with adjustable height support
legs for concrete floor installations
Code TILE-PLAIN-B
50mm Water Seal Trap Body 50mm Water Seal Trap Body 50mm Water Seal Trap Body
with 11/2" Multifit outlet. with 11/2" Multifit outlet. with 2" Multifit outlet.
Adjustable height 105-168mm. Adjustable height 120-168mm. Adjustable height 120-168mm.
Flow rate 34 l/min* Flow rate 42 l/min* Flow rate 50 l/min*
Sheet Flooring
■ Set the gully into the floor and ensure that the top surface of the gully flange is flush with, or
slightly below, the floor surface on which the flooring is to be laid
■ Ensure the gully body is fully supported, do not rely solely on the gully flange for support
■ A watertight seal between the underside of the sheet flooring and the gully flange must be
achieved with the use of a neutral sealant (not an acetoxy sealant) prior to the clamp ring
being screwed into position
Tiled Floors
■ The minimum dimension between the gully flange and top surface of the gully tile or grating,
which requires to be flush with the flooring, is 13mm. This dimension cannot be reduced but if
required the gully tile or grating can be raised. To do this remove the centre from the dust
cap/extension ring and solvent weld the extension ring to the upstand of the clamp ring. If
additional height is required an appropriate length of 110mm pipe can be solvent welded
between the extension ring and the underside of the gully tile or grating
■ Ensure the gully body is fully supported, do not rely solely on the gully flange for support
■ A good quality waterproofing membrane should be employed to prevent water penetration to
the floor structure. Ensure that the underside of the membrane is sealed to the gully flange and
secured by the clamp ring to the gully body
■ The clamp ring has weep holes to allow any moisture to discharge into the gully
Sheet Flooring
2 Moisture resistant
48 chipboard, marine ply or
wet room floor former
3 Floor joist
SECTION 2
Tiled Floors
1
1 Floor tiles
2 Waterproof tile adhesive
3 Waterproofing membrane
4 Concrete floor
Installation Guidelines
Stone Shower Base or Tray
3 Concrete floor
Conversion Kits
Conversion Cover Plate with 11/2" Universal Pipe Boss
For use with TSG1, TSG50, TSG52 and TSG2 shower gullies for sheet
flooring. Used to seal off gully or to convert to a drain connection to
allow for installation of bath waste. By refitting the cover plate and dip
tube the drain reverts to a trapped gully
Code CPTSG
Code TSGCONTVSS
Code FGTOP6SS
Accessories SECTION 2
Stopper for TSG Dip Tubes
For use with trapped shower gullies TSG1, TSG50, TSG52 and TSG2
models only, either sheet flooring or tiled floor versions. When after
installation the gully is not going to be used there is a possibility that
the water seal will evaporate. The stopper when inserted into the dip
tube will prevent foul air entering the building
Code TSGSTOP
Filter Mesh
Filter Mesh to suit USG1
range of untrapped
gullies
Code MESH-1
Stability Leg
Optional Stability Leg to
suit USG1 range of
untrapped gullies
Code USGLEG1
Accessories
51
Gully Flow Rates SECTION 2
All McAlpine gullies surpass the minimum required flow rate when tested in accordance with
clause 5 of BS EN 274-2:2002. The flow rate is tested under a constant 15mm head of water and will
vary depending on the tile grating cover plate used.