Shower and Floor Gullies

Shower and Floor Gullies, Channel Drain and Tile Drain

Channel Drain and Tile Drain SECTION

31
 General Information
Shower and Floor Gullies
■ McAlpine has responded to market conditions and customer demand by producing an extensive
range of gullies suitable for shower and wet floor areas
■ The comprehensive range of gullies is suitable for concrete and suspended timber floors finished
with sheet flooring, tiles or stone
■ Two-piece gullies enable the gully to be plumbed prior to installation of timber floors and wet room
floor formers
■ McAlpine gullies are ideal for domestic wet rooms, Lifetime Homes, disabled adaptations, student
accommodation, bathroom pods, hotels, hospitals, secure accommodation and sport and leisure
facilities
■ Manufactured in ABS to the highest quality, McAlpine gullies comply to EN 1253-2:2003
■ Flow rates of 48 litres per minute exceed the minimum requirement of EN 1253-2:2003 and are
variable dependent on the grating or cover plate used
■ Range of Trapped Shower Gullies (TSG) available with 50mm, 60mm and 75mm water seal,
Untrapped Shower Gullies (USG) for use with pumped waste and Valve Shower Gullies (VSG) for use
in floors where depth is restricted
■ Choice of horizontal or vertical outlet
■ All gullies have top access for easy cleaning
■ Choice of white plastic, polished stainless steel and chrome plated finishes for tiles, gratings,
clamp rings and cover plates

Channel Drain for Tiled Floors

■ The Channel Drain is suitable for concrete and suspended timber floors finished with tiles or stone
■ Manufactured in grade 304 stainless steel
■ Choice of brushed or polished finish cover plate reversible to accommodate tiles up to 8mm
■ Frame height adjustable to suit tiles up to 16mm

Tile Drain for Wet Floor Areas

General Information

■ The Tile Drain is suitable for concrete and suspended timber floors finished with tiles or stone
■ Manufactured in grade 304 stainless steel
■ Choice of 150m square stainless steel designer tiles reversible to accommodate tiles up to 8mm
■ Frame height adjustable to suit tiles up to 16mm

Code TSG50T6SS

32
Assembly and Features of Trapped Gullies SECTION 2
Sheet Flooring 1 Code TSG1-WH
1 Choice of cover plates with or without securing
screws 2
2 Cover plate and dip tube assembly. Choice of
cover plate finishes available

Assembly and Features of Trapped Shower Gullies

3 Removable sediment cup
3
4 Temporary cover plate. For use during installation
4
as a plug for preliminary air test. Will protect
gully from damage by foot traffic and prevent
site debris entering the drainage system 5
5 Clamp ring with 4 x M6 stainless steel screws

6 Four indentations suitable for size 8 countersunk 6

screws
7 Gully body with 2" BS EN 1329-1:2000 solvent
weld horizontal outlet 7
8 2" x 11/2" BS EN 1329-1:2000 socket reducer
8
Tile or Stone Floors
Code TSG2T6SS
1 Choice of tiles and gratings with or without
securing screws 1
2 Removable dip tube

3 Removable sediment cup

4 Dust cap/extension ring. For use during 2

installation to prevent site debris entering the
drainage system. The fitting can also be used for
raising the height of the tile 3
5 Clamp ring for waterproofing membrane and
solvent welding tile. The clamp ring has weep 4
holes to allow any moisture at this level to
discharge back into the gully and is secured by 4 x
M6 stainless steel screws 5
6 Four indentations suitable for size 8 countersunk
screws 6
7 Gully body with 110mm vertical outlet
8 110mm x 2" BS EN 1329-1:2000 solvent weld 7
reducer
33
■ The two products shown illustrate the versatility of
the McAlpine range of Trapped Shower Gullies.
See pages 34-38 for the full range of Trapped and 8
Untrapped Gullies
 Gullies for use with Sheet Flooring
Trapped Gullies White Plastic Polished CP Brass Clamp
Clamp Ring and Stainless Steel Ring, CP
Choose the appropriate gully body Cover Plate Clamp Ring and Stainless Steel
and cover plate finish required Cover Plate Grated Cover
Plate
Gullies without securing screws
allow for easier access

Do not pour drain cleaner down

these products

75mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and 2" x
11/2" socket reducer. Overall height 130mm

With
securing TSG1-WH TSG1SS TSG1SS-SL-SC
screws

Without
securing TSG1WH-NSC - TSG1SS-SL-NSC
Gullies for use with Sheet Flooring

screws

50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 100mm

With
securing TSG50WH TSG50SS TSG50SS-SL-SC
screws

Without
securing TSG50WH-NSC - TSG50SS-SL-NSC
screws

Two-Piece Gully, 50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal
outlet, 2" swivel outlet fitting and 2" x 11/2" socket reducer. Overall height 100mm

With
securing TSG52WH TSG52SS TSG52SS-SL-SC
screws

Without
securing TSG52WH-NSC - TSG52SS-SL-NSC
screws

75mm Water Seal Trap with 110mm vertical outlet and 110mm x 2" BS EN 1329-1:2000
solvent spigot outlet. Overall height 130mm

With
securing TSG2WH TSG2SS TSG2SS-SL-SC
screws

34 Without
securing TSG2WH-NSC - TSG2SS-SL-NSC
screws

Gullies show white cover plates for illustrative purposes only. See page 52 for gully flow rates
 SECTION 2
Trapped Gullies White Plastic Polished CP Brass Clamp
Clamp Ring and Stainless Steel Ring, CP
Choose the appropriate gully body Cover Plate Clamp Ring and Stainless Steel
and cover plate finish required Cover Plate Grated Cover
Plate
Gullies without securing screws
allow for easier access

Do not pour drain cleaner down

these products

50mm Water Seal Trap with 11/2" BS EN 1329-1:2000 solvent weld side inlet for the discharge
from a wash hand basin with a 110mm vertical outlet to fit 110mm pipe socket or vertical
11/2" solvent weld pipework. Overall height 130mm

With
securing TSG3-WH TSG3SS TSG3SS-SL-SC
screws

Without

Gullies for use with Sheet Flooring

securing - - TSG3SS-SL-NSC
screws

Gullies show white cover plates for illustrative purposes only

Untrapped Gullies
Untrapped Gully with 22mm horizontal plain outlet for use with pumped waste.
Overall height 44.5mm

With
securing USG1WH USG1SS USG1SS-SL-SC
screws

Untrapped Gully with 2" BS EN 1329-1:2000 solvent weld vertical outlet and 2" x 11/2"
socket reducer. Overall height 70.5mm

With
securing USG2SS-SL-SC
USG2WH USG2SS
screws

Untrapped Gully with 11/2" BS EN 1329-1:2000 solvent weld horizontal outlet.

Overall height 70.5mm

With
securing
USG3WH USG3SS USG3SS-SL-SC 35
screws

Gullies show white cover plates for illustrative purposes only. See page 52 for gully flow rates
 Gullies for use with Tiled or Stone Floors where a Waterproofing
Trapped Gullies 150mm Square 150mm Square 125mm
Polished White ABS Tile Diameter Polished
Choose the appropriate gully body Stainless Steel with removable Stainless Steel
and cover plate finish required Tile with Grid Grating with
removable Grid removable Grid
Gullies without securing screws
allow for easier access

Do not pour drain cleaner down

these products

75mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 130mm

With
Gullies for use with Tiled or Stone Floors

securing TSG1T6SS - -
screws

Without
securing TSG1-T150SS TSG1T6WH TSG1-R125SS
screws

50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal outlet and
2" x 11/2" socket reducer. Overall height 100mm

With
securing TSG50T6SS - -
screws

Without
securing TSG50-T150SS TSG50T6WH TSG50-R125SS
screws

Two-Piece Gully, 50mm Water Seal Trap with 2" BS EN 1329-1:2000 solvent weld horizontal
outlet, 2" swivel outlet fitting and 2" x 11/2" socket reducer. Overall height 100mm

With
securing TSG52T6SS - -
screws

Without
securing TSG52-T150SS TSG52T6WH TSG52-R125SS
screws

75mm Water Seal Trap with 110mm vertical outlet and 110mm x 2" BS EN 1329-1:2000
solvent spigot outlet. Overall height 130mm

With
securing TSG2T6SS - -
screws

Without
36
securing TSG2-T150SS TSG2T6WH TSG2-R125SS
screws

Gullies show square stainless steel cover plates for illustrative purposes only. All above gullies supplied
with white plastic clamp ring. See page 52 for gully flow rates
Membrane is required SECTION 2
Untrapped Gullies 150mm Square 150mm Square 125mm
Polished White ABS Tile Diameter Polished
Choose the appropriate gully body Stainless Steel with removable Stainless Steel
and cover plate finish required Tile with Grid Grating with
removable Grid removable Grid
Gullies without securing screws
allow for easier access

Do not pour drain cleaner down

these products

Untrapped Gully with 22mm horizontal plain outlet for use with pumped waste.
Overall height 44.5mm
With
securing USG1T6SS - -

Gullies for use with Tiled or Stone Floors

screws
Without
securing USG1-T150SS - -
screws

Untrapped Gully with 2" BS EN 1329-1:2000 solvent weld vertical outlet and 2" x 11/2" socket
reducer. Overall height 70.5mm
With
securing USG2T6SS - -
screws
Without
securing USG2-T150SS - -
screws

Untrapped Gully with 11/2" BS EN 1329-1:2000 solvent weld horizontal outlet.

Overall height 70.5mm
With
securing USG3T6SS - -
screws
Without
securing USG3-T150SS - -
screws

37

Gullies show square stainless steel cover plates for illustrative purposes only.
See page 52 for gully flow rates
 Two-Piece Gully and Gully with Non-Return Valve
■ Two-piece gullies have been specifically ■ The Valve Shower Gully (VSG) has been
designed for use with timber floors and floor developed to satisfy customer demand for a
formers and can be plumbed prior to the shallow gully suitable for installation in
installation of the floor or former. See pages floors where depth is restricted
34-40 for product range
Two-Piece Gully and Gully with Non-Return Valve

Code VSG1WH-NSC

38

Code TSG52T6SS
Gullies with Non-Return Valve for use where floor
depth is restricted SECTION 2
■ The Valve Shower Gully (VSG) has been developed to satisfy customer demand for a shallow gully
suitable for installation in floors where depth is restricted
■ The overall height of the VSG1 is only 75mm and the valve is a substitute for a regulatory water
seal trap which cannot be incorporated in a gully of this height
■ There are currently no regulations to cover the use of anything other than water seal traps in
domestic drainage systems. Although valves have been in existence for some time, it is advisable
to seek guidance from the local building control department prior to use
■ The valve acts as a non-return valve, the weight of the water discharge will open the valve and it
will reseal when the discharge has ceased thus prohibiting foul air from entering the dwelling
■ The valve eliminates the release of foul air due to back flow
■ The valve can be easily removed to facilitate easy cleaning of the gully
■ The VSG range has a minimum flow rate of 30 litres per minute when tested with a 15mm head
of water

White Plastic Clamp Ring with Cover Plate and 11/2"

BS EN 1329-1:2000 solvent weld horizontal outlet.
Overall height 75mm
Code
With securing screws VSG1WH

Gullies with Non-Return Valve

Without securing screws VSG1WH-NSC

Two-Piece Gully, White Plastic Clamp Ring with Cover Plate and
11/2" BS EN 1329-1:2000 solvent weld horizontal outlet.
Overall height 85mm

With securing screws VSG52WH

150mm Square Polished Stainless Steel Tile with removable

Grid and Securing Screws 11/2" BS EN 1329-1:2000 solvent weld
horizontal outlet.
Overall height 75mm

VSG1T6SS

39

Gullies without securing screws allow for easier access See page 52 for gully flow rates

Do not pour drain cleaner down these products

 Gullies with Non-Return Valve for use where floor
depth is restricted
Two-Piece Gully, 150mm Square Polished Stainless Steel Tile
with removable Grid and Securing Screws
11/2" BS EN 1329-1:2000 solvent weld horizontal outlet.
Overall height 85mm

Code VSG52T6SS

Gullies with Anti-Ligature Grating for use with Sheet

Shower Gullies with Anti-Ligature Grating

Flooring
■ Shower gullies with anti-ligature grating have been designed for use in secure accommodation
■ Grating is Home Office approved
■ All gullies supplied with security screwdriver bit to release anti-ligature grating
75mm Water Seal Trap 2" BS EN 1329-1:2000 solvent weld
horizontal outlet and 2" x 11/2" socket reducer. CP brass clamp
ring with polished stainless steel anti-ligature grating.
Overall height 130mm

Code TSG1-ANTI/LIG

50mm Water Seal Trap 2" BS EN 1329-1:2000 solvent weld

horizontal outlet and 2" x 11/2" socket reducer. CP brass clamp
ring with polished stainless steel anti-ligature grating.
Overall height 100mm

Code TSG50-ANTI/LIG

Two-Piece Gully, 50mm Water Seal Trap 2" BS EN 1329-1:2000

solvent weld horizontal outlet, 2" swivel outlet fitting and
2" x 11/2" socket reducer. CP brass clamp ring with polished
stainless steel anti-ligature grating.
Overall height 100mm

Code TSG52-ANTI/LIG

75mm Water Seal Trap with 110m vertical outlet and 110mm x
2" BS EN 1329-1:2000 solvent weld reducer. CP brass clamp
ring with polished stainless steel anti-ligature grating.
Overall height 130mm

40 Code TSG2-ANTI/LIG

See page 52 for gully flow rates

Top Access Shower Traps for use with Sheet Flooring,

Top Access Shower Traps for use with Sheet Flooring, Tiled or Stone Floors
Tiled or Stone Floors SECTION 2
For Sheet Flooring
19mm Water Seal Trap with 11/2" universal compression outlet, white
plastic clamp ring and cover plate with securing screws.
Overall height 138mm

Code TSG1WH-STW1R

For Sheet Flooring

50mm Water Seal Trap with 11/2" x 90° swivel Multifit outlet bend,
white plastic clamp ring and cover plate with securing screws.
Overall height 138mm

Code TSG1WHSTW295

For Sheet Flooring

50mm Water Seal Resealing Trap with 11/2" x 90° swivel Multifit outlet
bend, white plastic clamp ring and cover plate with securing screws.
Overall height 167mm

Code TSG1WH-STW2R

For Tiled or Stone Floors

19mm Water Seal Trap with 11/2" universal compression outlet,
150mm square polished stainless steel tile with removable grid and
securing screws.
Overall height 138mm
Code TSG1T6SS+STW1-R

For Tiled or Stone Floors

50mm Water Seal Trap with 11/2" x 90° swivel Multifit outlet bend,
150mm square polished stainless steel tile with removable grid and
securing screws.
Overall height 138mm

Code TSG1T6SSSTW295

For Tiled or Stone Floors

50mm Water Seal Resealing Trap with 11/2" x 90° swivel Multifit outlet
bend, 150mm square polished stainless steel tile with removable grid
and securing screws.
Overall height 167mm

41
Code TSG1T6SS-STW2R

See page 52 for gully flow rates Do not pour drain cleaner down these products
 Tiles and Gratings
150mm Square Polished Stainless Steel Tile with removable grid and
securing screws. Tile has ABS spigot adaptor for solvent welding to clamp
ring
Code FGTOP6SS
150mm Square Polished Stainless Steel Tile with removable grid. Tile
has a removable ABS spigot adaptor for solvent welding to clamp ring
leaving a rubber gasket to fit inside 110mm pipe
Code FGT150TOP

150mm Square White ABS Tile with removable grid. Tile has spigot
adaptor for solvent welding to clamp ring

Code MDTOP-WH
200mm Square White ABS Tile with removable grid. Tile has spigot
adaptor for solvent welding to clamp ring

Code MDTOP20-WH
125mm Diameter Polished Stainless Steel Grating with removable grid.
Grating has a removable ABS spigot adaptor for solvent welding to
clamp ring leaving a rubber gasket to fit inside 110mm pipe. Suitable
for stone shower bases
Code FGTR125TOP

150mm Stainless Steel Tile with Internal Non-Return Valve

■ Suitable for wet floor areas where ■ Ideal for replacement and repair of a
4"/110mm drainage pipework has been damaged tile or problem systems
installed to the finished floor level and no ■ Push-fit or solvent weld spigot suitable for
waterproofing membrane is required direct connection to 4"/110mm drainage
■ The internal non-return valve prevents foul pipework
Tiles and Gratings

air entering the building ■ Valve easily removed for cleaning and
■ The 150mm square tile can be fitted on a maintenance work
trapped or untrapped drain
150mm square stainless steel
tile with silicone non-return
valve and removable grid
including removable stainless
steel mesh filter

Code FGT150-SV-110

150mm square stainless steel

tile with silicone non-return
valve and securing screws. ABS
solvent weld connection to
42 4"/110mm drainage pipework

Code FGT150-SV-110S
Gullies suitable for Concrete Ground Floors where a
Waterproofing Membrane is not required SECTION 2
Trapped Gully Bodies
Multi-Drain - 60mm Water Seal Universal Trapped Floor Gully
manufactured in grey ABS with 2"/3" solvent weld horizontal outlet.
Height can be extended by solvent welding length of 110mm PVC pipe
between gully body and tile. Inlet connections are for solvent welding to
11/2" ABS/PVC pipe, internal fit or 2" ABS/PVC pipe, external fit.
Overall height 152mm

For Tiles and Gratings see page 42

Gullies suitable for Concrete Ground Floors

Code MD100

Multi-Drain - 60mm Water Seal Universal Trapped Floor Gully

manufactured in grey ABS with 3" solvent weld horizontal outlet. Height
can be extended by solvent welding length of 110mm PVC pipe between
gully body and tile. Inlet connections are for solvent welding to 11/2"
ABS/PVC pipe, internal fit or 2" ABS/PVC pipe, external fit.
Overall height 152mm

For Tiles and Gratings see page 42

Code MD100-3

Adaptors for Inlet and Outlet Connections

Multi-Drain Inlet Fitting Multi-Drain Outlet Fitting
2" solvent weld x 2" universal 3" solvent weld x 110mm
compression solvent weld

Code MD200 Code MD400

Untrapped Gullies with Top Access for Tiled Floors

Untrapped Gully with 11/2" BS EN 1329-1:2000 solvent weld horizontal
outlet and 150mm square polished stainless steel tile with removable
grid and securing screws.
Overall height 68mm
Code FD90-T6SS

Untrapped Gully with 11/2" BS EN 1329-1:2000 solvent weld horizontal

outlet and 150mm square white ABS tile with removable grid.
Overall height 68mm

Code FD90-T6WH 43

Do not pour drain cleaner down these products

 Channel Drain for Tiled Floors
■ Supplied with 11/2" x 50mm water seal trap ■ Flow rate 54 litres per minute. Calculated
with top access for easy cleaning under a constant 120mm head of water
■ Available with polished or brushed finished ■ Supplied with adjustable height support
grade 304 stainless steel cover plate legs for concrete floor installations.
■ Cover plate reversible to accommodate tiles Adjustable height 128-170mm
up to 8mm ■ There are two McAlpine ranges: Standard
■ Frame height adjustable to suit tiles up to and Slimline channel drains. Both are
16mm available in a choice of lengths, designs and
finishes

Standard Channel Drain for Tiled Floors

31mm CD1200 - 1148mm 31mm
CD1000 - 948mm
CD900 - 848mm
CD800 - 748mm
CD700 - 648mm
CD600 - 548mm

20.5 -
85mm

Width of Channel Frame 88mm

Channel Drain for Tiled Floors

25.5mm

44

Do not pour drain cleaner down these products

 SECTION 2

Standard Channel Drain with brushed Standard Channel Drain with grid (brushed
finish cover plate finish)
Code CD600-B Code CD600-SQ
Code CD700-B Code CD700-SQ
Code CD800-B Code CD800-SQ
Code CD900-B Code CD900-SQ
Code CD1000-B Code CD1000-SQ
Code CD1200-B Code CD1200-SQ

Channel Drain for Tiled Floors

Standard Channel Drain with polished
finish cover plate
Code CD600-P
Code CD700-P
Code CD800-P
Code CD900-P
Code CD1000-P
Code CD1200-P

Cover plates available separately on request

Scan here to view our Installation

video or visit our website
www.mcalpineplumbing.com
45

Do not pour drain cleaner down these products

 Channel Drain for Tiled Floors
Slimline Channel Drain for Tiled Floors
31mm CD1200 - 1148mm
CD1000 - 948mm
CD900 - 848mm
CD800 - 748mm
CD700 - 648mm
CD600 - 548mm

20.5 -
Width of Channel Frame 51mm
85mm

25.5mm
Channel Drain for Tiled Floors

Slimline Channel Drain with brushed finish Slimline Channel Drain with polished finish
cover plate cover plate
Code CD600-O-B Code CD600-O-P
Code CD700-O-B Code CD700-O-P
Code CD800-O-B Code CD800-O-P
46 Code CD900-O-B Code CD900-O-P
Code CD1000-O-B Code CD1000-O-P
Code CD1200-O-B Code CD1200-O-P
Cover plates available separately on request Do not pour drain cleaner down these products
Tile Drain for Wet Floor Areas SECTION 2
■ Tiles suitable for 50mm water seal traps as
illustrated
■ Tiles supplied with brushed or polished
finish. All in grade 304 stainless steel
■ Tiles reversible to accommodate tiles up to
8mm
■ Tile frame dimension 150mm square
■ Frame height adjustable to suit tiles up to
16mm
■ Supplied with adjustable height support
legs for concrete floor installations

Code TILE-PLAIN-B

Tile Drain for Wet Floor Areas

Code TILE-PLAIN-P

50mm Water Seal Trap Body 50mm Water Seal Trap Body 50mm Water Seal Trap Body
with 11/2" Multifit outlet. with 11/2" Multifit outlet. with 2" Multifit outlet.
Adjustable height 105-168mm. Adjustable height 120-168mm. Adjustable height 120-168mm.
Flow rate 34 l/min* Flow rate 42 l/min* Flow rate 50 l/min*

Code ST90-70B Code ST90-HP2B Code ST90-HPB 47

*Flow rate calculated under a constant 15mm head of water

Do not pour drain cleaner down these products

 Installation Guidelines
General Notes and Guidance for Shower Gullies
■ All Trapped (TSG), Untrapped (USG) and Valve (VSG) shower gullies can be used in concrete or
suspended timber floors
■ All gullies are ideal for shower and wet floor areas
■ Fixing instructions are supplied with each gully

Sheet Flooring
■ Set the gully into the floor and ensure that the top surface of the gully flange is flush with, or
slightly below, the floor surface on which the flooring is to be laid
■ Ensure the gully body is fully supported, do not rely solely on the gully flange for support
■ A watertight seal between the underside of the sheet flooring and the gully flange must be
achieved with the use of a neutral sealant (not an acetoxy sealant) prior to the clamp ring
being screwed into position
Tiled Floors
■ The minimum dimension between the gully flange and top surface of the gully tile or grating,
which requires to be flush with the flooring, is 13mm. This dimension cannot be reduced but if
required the gully tile or grating can be raised. To do this remove the centre from the dust
cap/extension ring and solvent weld the extension ring to the upstand of the clamp ring. If
additional height is required an appropriate length of 110mm pipe can be solvent welded
between the extension ring and the underside of the gully tile or grating
■ Ensure the gully body is fully supported, do not rely solely on the gully flange for support
■ A good quality waterproofing membrane should be employed to prevent water penetration to
the floor structure. Ensure that the underside of the membrane is sealed to the gully flange and
secured by the clamp ring to the gully body
■ The clamp ring has weep holes to allow any moisture to discharge into the gully

Stone Shower Bases and Trays

■ Gullies can be used with stone or marble shower bases and trays. The illustration shows how a
125mm diameter polished stainless steel grating can be connected to a 50mm water seal gully
■ A waterproofing membrane should be fitted between the gully body and the underside of the
base or tray
Installation Guidelines

Sheet Flooring

1 Flexible sheet flooring

2 Moisture resistant
48 chipboard, marine ply or
wet room floor former

3 Floor joist
 SECTION 2

Tiled Floors
1

1 Floor tiles
2 Waterproof tile adhesive
3 Waterproofing membrane
4 Concrete floor

Installation Guidelines
Stone Shower Base or Tray

1 Stone base or tray

2 Waterproofing membrane 49

3 Concrete floor
 Conversion Kits
Conversion Cover Plate with 11/2" Universal Pipe Boss
For use with TSG1, TSG50, TSG52 and TSG2 shower gullies for sheet
flooring. Used to seal off gully or to convert to a drain connection to
allow for installation of bath waste. By refitting the cover plate and dip
tube the drain reverts to a trapped gully

Code CPTSG

Conversion Kits to enable Gullies except MD100, MD100-3 and FD90 to

be converted for different floor finishes
Converts any TSG1 or
TSG2 Gully from tiled Converts any TSG1 or
to a sheet flooring TSG2 Gully to a tiled
gully with dip tube, CP floor gully with white
brass clamp ring, CP ABS clamp ring,
stainless steel grated 150mm square white
cover plate without ABS tile with
securing screws removable grid and dip
Code FGTR118TOP tube
Converts any TSG50 or
Code TSGCONV
TSG52 Gully to a sheet
flooring gully with dip
tube, CP brass clamp
ring, CP stainless steel
grated cover plate with Converts any TSG1 or
securing screws TSG2 Gully to a tiled
floor gully with white
Code FGTR118TOP-50 ABS clamp ring,
Converts any TSG1 or 150mm square
TSG2 Gully to a sheet polished stainless steel
Conversion Kits

flooring gully with tile with removable

white plastic clamp grid, securing screws
ring, cover plate and and dip tube
dip tube
Code TSGCONVSS
Code TSGCONTV
Converts any Gully
Converts any TSG1 or
with a 150mm White
TSG2 Gully to a sheet
Plastic Tile to a gully
flooring gully with
with a 150mm square
polished stainless steel
polished stainless steel
clamp ring, cover plate
50 tile with removable
and dip tube
grid and securing screws

Code TSGCONTVSS
Code FGTOP6SS
Accessories SECTION 2
Stopper for TSG Dip Tubes
For use with trapped shower gullies TSG1, TSG50, TSG52 and TSG2
models only, either sheet flooring or tiled floor versions. When after
installation the gully is not going to be used there is a possibility that
the water seal will evaporate. The stopper when inserted into the dip
tube will prevent foul air entering the building

Code TSGSTOP

Filter Mesh
Filter Mesh to suit USG1
range of untrapped
gullies

Code MESH-1

Stability Leg
Optional Stability Leg to
suit USG1 range of
untrapped gullies

Code USGLEG1

Accessories

51
 Gully Flow Rates SECTION 2
All McAlpine gullies surpass the minimum required flow rate when tested in accordance with
clause 5 of BS EN 274-2:2002. The flow rate is tested under a constant 15mm head of water and will
vary depending on the tile grating cover plate used.

Flow Rate Flow Rate Flow Rate

Litres per Litres per Litres per
Code minute Code minute Code minute
TSG1-ANTI/LIG 31 TSG3SS-SL-NSC >70 USG1SS-SL-SC 10

TSG1-R125SS 56.9 TSG3SS-SL-SC >70 USG1-T150SS 10

TSG1SS 50 TSG3-T150SS >70 USG1T6SS 10

TSG1SS-SL-NSC 53.6 TSG3T6SS >70 USG1WH 10

TSG1SS-SL-SC 53.6 TSG3T6WH >70 USG1WH-NSC 10

TSG1-T150SS 55 TSG3WH 65.1 USG2SS 68

TSG1T6SS 55 TSG50-ANTI/LIG 44 USG2SS-SL-NSC 68

TSG1T6SS+STW1R 35 TSG50-R125SS 54.3 USG2SS-SL-SC 68

TSG1T6SSSTW295 32 TSG50SS 48 USG2-T150SS 68

TSG1T6SS-STW2R 37 TSG50SS-SL-NSC 50.3 USG2T6SS 68

TSG1T6WH 55 TSG50SS-SL-SC 50.3 USG2WH 68

TSG1-WH 53 TSG50-T150SS 53.6 USG3SS 65

TSG1WH-NSC 53 TSG50T6SS 52.6 USG3SS-SL-NSC 65

TSG1WH-STW1R 35 TSG50T6WH 52.5 USG3SS-SL-SC 65

TSG1WHSTW295 32 TSG50WH 50.5 USG3-T150SS 65

TSG1WH-STW2R 37 TSG50WH-NSC 51 USG3T6SS 65

Gully Flow Rates

TSG2-ANTI/LIG >70 TSG52-ANTI/LIG 44 USG3WH 65

TSG2-R125SS >70 TSG52-R125SS 54.3 VSG1T6SS 30

TSG2SS >70 TSG52SS 48 VSG1T6WH 30

TSG2SS-SL-NSC >70 TSG52SS-SL-NSC 50.3 VSG1WH 30

TSG2SS-SL-SC >70 TSG52SS-SL-SC 50.3 VSG1WH-NSC 30

TSG2-T150SS >70 TSG52-T150SS 53.6 VSG52T6SS 36

TSG2T6SS >70 TSG52T6SS 52.5 VSG52T6WH 36

TSG2T6WH >70 TSG52T6WH 52.5 VSG52WH 36

TSG2WH >70 TSG52WH 50.5 VSG52WH-NSC 36

52 TSG2WH-NSC >70 TSG52WH-NSC 51

TSG3-R125SS >70 USG1SS 10

TSG3SS 64.5 USG1SS-SL-NSC 10