Oil Characterization 1

Oil Characterization

1
© 2003 AspenTech. All Rights Reserved.
EA1031.31.05
05 Oil Characterization.pdf
2 Oil Characterization

Workshop
The petroleum characterization method in HYSYS converts laboratory
analyses of condensates, crude oils, petroleum cuts, and coal-tar liquids
into a series of discrete hypothetical components. These petroleum
hypo components provide the basis for the property package to predict
the remaining thermodynamic and transport properties necessary for
fluid modeling.

HYSYS produces a complete set of physical and critical properties for

the petroleum hypocomponents with a minimal amount of
information. However, the more information you supply about the fluid,
the more accurate these properties will be, and the better HYSYS will
predict the fluid’s actual behaviour.

In this example, the Oil Characterization option in HYSYS is used to

model a reservoir fluid. The fluid is a combined gas and oil stream.

Learning Objectives
Once you have completed this section, you will be able to:

• Understand the steps required for oil characterization.

• Characterize an oil using chromatographic data.

Prerequisites
Before beginning this module you need to understand the basics of the
fluid package (Getting Started).

2
 Oil Characterization 3

Process Overview
Mole Mass Volume
Component
Fraction Fraction Fraction
N2 0.0048 0.0017 0.0014
CO2 0.0087 0.0048 0.0039
H2S 0.0000 0.0000 0.0000
C1 0.4183 0.0843 0.1871
C2 0.0887 0.0335 0.0626
C3 0.0711 0.0394 0.0517
i-C4 0.0147 0.0107 0.0127
n-C4 0.0375 0.0274 0.0312
i-C5 0.0125 0.0113 0.0121
n-C5 0.0163 0.0148 0.0156
C6+ 0.3274 0.7721 0.6217
H2O 0.0000 0.0000 0.0000
TOTAL 1.0000 1.0000 1.0000

Relative Density Relative

Residue Data Summary
@ 15°C Molecular Mass
OBS CALC OBS CALC MOLE MASS VOLUME
FRACTION FRACTION FRACTION
C6+ 0.8265 188 0.3274 0.7721 0.6217

TOTAL 0.6659 79.6

SAMPLE

Paraffinic Component Groups (Molar Fractions)

Component B.Pt. Temp (°C) Mole
Hexane (C6) 68.9 0.0268
Heptane (C7) 98.3 0.0371
Octane (C8) 125.6 0.0348
Nonane (C9) 150.6 0.0231
Decane (C10) 173.9 0.0240
Undecane (C11) 196.1 0.0183
Dodecane (C12) 215.0 0.0142
Tridecane (C13) 235.0 0.0141
Tetradecane 252.2 0.0113
Pentadecane 270.6 0.0099
Hexadecane 287.8 0.0074
Heptadecane 302.8 0.0082

3
4 Oil Characterization

Paraffinic Component Groups (Molar Fractions)

Component B.Pt. Temp (°C) Mole
Octadecane 317.2 0.0062
Nonadecane 330.0 0.0049
Eicosane (C20) 344.4 0.0046
Heneicosane 357.2 0.0039
Docosane (C22) 369.4 0.0036
Tricosane (C23) 380.0 0.0032
Tetracosane 391.1 0.0027
Pentacosane 401.7 0.0024
Hexacosane 412.2 0.0021
Heptacosane 422.2 0.0020
Octacosane 431.7 0.0018
Nonacosane 441.1 0.0016
Triconane Plus 450.0 0.0133
Aromatic Component Groups (Molar Fractions)
Benzene (C6H6) 80.0 0.0004
Toluene (C7H8) 110.6 0.0015
EBZ, p+m-Xylene 136.1 0.0070
o-Xylene (C8H10) 144.4 0.0028
1,2,4 168.9 0.0028
Naphthenic Component Groups (Molar Fractions)
Cyclopentane 48.9 0.0002
MethylCycloPenta 72.2 0.0106
Cyclohexane 81.1 0.0050
MethylCycloHexa 101.1 0.0156

TOTALS 0.3274

4
 Oil Characterization 5

Building the Simulation

Before you start the characterization process, you must:

• Select a property package.

• Add any non-oil components, specifically the light ends that are to
be used in the characterization process.

Defining the Simulation Basis

For this module, you will be building on the case you started in the
Getting Started Module.

1. Open the case you saved at the end of the Getting Started module.
2. Click the Enter Basis Environment icon to return to the Basis
Enter Basis Environment icon Environment.
3. Go to the Oil Manager tab and click the Enter Oil Environment
button. You could also press the Oil Environment button on the tool
Bar. The Oil Characterization view appears.

Oil Environment icon Figure 1

5
6 Oil Characterization

Oil Characterization
The petroleum characterization in HYSYS accepts different types of
The Minimum amount of information about the oil. The more information you can supply about
information that HYSYS your sample, the more accurate the representation.
requires to characterize an
oil:
There are three steps involved in characterizing any oil in HYSYS:
• a laboratory distillation
curve
or 1. Characterize the assay.
• two of the following 2. Generate hypocomponents.
bulk properties:
Molecular Weight, 3. Install the oil in the flowsheet.
Density, or Watson K
Factor.

Characterize the Assay

The assay contains all of the petroleum laboratory data, boiling point
curves, light ends, property curves, and bulk properties. HYSYS uses the
supplied assay data to generate internal TBP, molecular weight, and
density and viscosity curves (referred to as Working Curves).

Assay Types
Accurate volatility characteristics are vital when representing a
petroleum fluid in your process simulation. HYSYS accepts the following
standard laboratory analytical assay procedures:

• True Boiling Point (TBP). Performed using a multi-stage batch

fractionation apparatus operated at relatively high reflux ratios.
TBP distillations conducted at atmospheric or vacuum conditions
are accepted by the characterization.
• ASTM D86. Distillation employing batch fractionation but
conducted using non-refluxed Engler flasks. Generally used for
light to medium petroleum fluids. HYSYS can correct for
barometric pressure or cracking effects. You must provide the
data on a liquid volume basis.
• D1160 distillation. Distillation employing batch fractionation but
conducted using non-refluxed Engler flasks. Generally used for
For all Distillation Curves,
heavier petroleum fluids. Curves can be given at atmospheric
you are required to enter at pressure or corrected for vacuum conditions. You must provide
least five data points. the data on a liquid volume basis.

6
 Oil Characterization 7

• D86_D1160. This is a combination of the D86/D1160 distillation

data types. You can correct for thermal cracking and enable
vacuum distillation for sub-atmospheric conditions. You must
provide data on a liquid volume basis.
• ASTM D2887. Simulated distillation analysis from
chromatographic data. Reported only on a weight percent basis
at atmospheric conditions.
• Equilibrium Flash Vaporization (EFV). Involves a series of
experiments at constant atmospheric pressure, where the total
vapour is in equilibrium with the unvapourized liquid.
• Chromatographic Analysis. A gas chromatograph analysis of a
small sample of completely vapourized oil, analyzed for paraffin,
aromatic and naphthenic hydrocarbon groups from C6 to C30.
Chromatographic analyses may be entered on a mole, mass or
liquid volume basis.

Light Ends
Light Ends are defined as pure components with low boiling points.
Components in the boiling range of C2 to n-C5 are most commonly of
interest.

HYSYS provides three options to account for Light Ends:

• Ignore. HYSYS characterizes the Light Ends portion of your

sample as hypocomponents. This is the least accurate method
and as such, is not recommended.
• Auto Calculate. Select this when you do not have a separate
Light Ends analysis but you want the low boiling portion of your
assay represented by pure components. HYSYS will only use the
pure components you have selected in the fluid package.
• Input Composition. Select this when you have a separate Light
Ends assay and your petroleum assay was prepared with the
Light Ends in the sample. HYSYS will provide a form listing the
pure components you selected in the fluid package. This is the
most accurate method of representation.

Bulk Properties
Bulk Properties for the sample may also be supplied. The bulk
properties are optional if a distillation curve or chromatograph have
been supplied.

• Molecular Weight. This is the Molecular Weight of the bulk

sample. It must be greater than 16.

7
8 Oil Characterization

• Mass Density. The mass density must be between 250 and 2000
kg/m3.
• Watson (UOP) K Factor. This must be between 8 and 15.
• Bulk Viscosities. Given at two reference temperatures, typically
37.78°C and 98.89°C (100°F and 210°F).
• The units for density
can be mass density,
API or specific gravity,
chosen from the drop
down list in the Edit
Physical Property Curves
Bar
• The Watson K Factor HYSYS accepts different types of physical property curves:
is an approximate
index of paraffinicity. K
= (Mean Avg BP)1/3/ • Molecular weight curve
(sp gr 60F/60F)
• Density curve
• Viscosity curve

Physical property analyses are normally reported from the laboratory

using one of the following two conventions:

• Independent Assay Basis. A common set of assay fractions is

not used for both the distillation curve and the physical property
curve.
• Dependent Assay Basis. A common set of assay fractions is
used for both the distillation curve and the physical property
curve.

As you supply more information to HYSYS, the accuracy of the

petroleum characterization increases. Supplying any or all of the bulk
molecular weight, bulk density, or bulk Watson K factor will increase the
accuracy of your hypocomponent properties. You can also supply
laboratory curves for molecular weight, density, and/or viscosity which
will increase the accuracy further.

Adding Assay Data

On the Oil Characterizations view:

1. Select Assay tab.

2. Click the Add button.
3. The Input Data tab of the Assay view appears.
4. In the Name cell, change the assay name to Res-Fluid.
5. For the Bulk Props cell, use the drop-down list to select Used.
6. From the Assay Data Type drop-down list, select Chromatograph.

8
 Oil Characterization 9

7. Once the correct Data Type is chosen, a third cell should appear.
This is the Light Ends cell; use the drop-down list to select Input
Composition as shown below.

Figure 2

8. Select the Light Ends radio button in the Input Data group.
9. Specify the Light Ends Basis as Mole %.
10. Enter the following data. Note that the default basis for Light Ends is
You need to enter the light Liquid Volume %; this must be changed before the data is entered.
components in the fluid
package for them to be
For this Component... Enter this Mole Fraction...
available to the Oil Manager.
N2 0.48
H2S 0.00
CO2 0.87
C1 41.83
C2 8.87
C3 7.11
i-C4 1.47
n-C4 3.75
i-C5 1.25
n-C5 1.63
C6 0.00
H2O 0.00

9
10 Oil Characterization

11. Select the Paraffinic radio button and specify the Basis as Mole.
Enter the following data.:

For this component... Enter this Mole Fraction...

Hexane (C6) 0.0268
Heptane (C7) 0.0371
Octane (C8) 0.0348
Nonane (C9) 0.0231
Decane (C10) 0.0240
Undecane (C11) 0.0183
Dodecane (C12) 0.0142
Tridecane (C13) 0.0141
Tetradecane (C14) 0.0113
Pentadecane (C15) 0.0099
Hexadecane (C16) 0.0074
Heptadecane (C17) 0.0082
Octadecane (C18) 0.0062
Nonadecane (c19) 0.0049
Eicosane (C20) 0.0046
Heneicosane (C21) 0.0039
Docosane (C22) 0.0036
Tricosane (C23) 0.0032
Tetracosane (C24) 0.0027
Pentacosane (C25) 0.0024
Hexacosane (C26) 0.0021
Heptacosane (C27) 0.0020
Octacosane (C28) 0.0018
Nonacosane (C29) 0.0016
Triconane Plus 0.0133

12. Select the Aromatic radio button, and enter the following mole
fractions:

For this Component... Enter this Mole Fraction...

Benzene (C6H6) 0.0004
Toluene (C7H8) 0.0015
EBZ, p+m-Xylene (C8H10) 0.0070
o-Xylene (C8H10) 0.0028
1,2,4 TriMethylBenzene (C9H12) 0.0028

10
 Oil Characterization 11

13. Enter the following data for the Naphthenic components:

For this component... Enter this Mole Fraction...

Cyclopentane (C5H10) 0.0002
MethylCycloPentane (C6H12) 0.0106
Cyclohexane (C6H12) 0.0050
MethylCycloHexane (C7H14) 0.0156

14. Select the Bulk Props radio button to enter the Bulk information.
Just as with fluid packages, 15. The Molecular Weight is 79.6 and the Standard Density is 0.6659
assays can be imported and
SG_60/60api.
exported to be used in
different cases. 16. Once you have entered all of the data, click the Calculate button.
The status message at the bottom of the Assay view will display
Assay Was Calculated. HYSYS indicates that the sum of all fractions
does not equal to 1.

Once the Assay is calculated, the working curves are displayed on the
Working Curves tab. The working curves are regressed from the Assay
input. The calculation of the Blend is based on these working curves.

17. Close this view to return to the Oil Characterization view. You
should still be on the Assay tab of the view.

Notice that all of the buttons on the view are now accessible.

Hypocomponent Generation/Blending the Oil

The Cut/Blend characterization in HYSYS splits the internal working
curves for one or more assays into hypocomponents. The Blend tab of
the Oil Characterization view provides two functions, Cutting the Oil
into Hypocomponents and Blending two or more Assays into one set of
hypocomponents.

11
12 Oil Characterization

Cut Ranges
You have three choices for the Cut Option Selection:

• Auto Cut - HYSYS cuts the assay based on internal values

Range Cuts
37.78 - 425°C (100 - 800°F) 28 (4 per 37.78°C/100°F)
425 - 650°C (800 - 1200°F) 8 (2 per 37.78°C/100°F)
650 - 870°C (1200 - 1600°F) 4 (1 per 37.78°C/100°F)

• User Points - You specify the number of hypocomponents

required. HYSYS proportions the cuts according to an internal
weighting scheme.

Cutpoint Range Internal Weighting

IBP - 425°C (IBP - 800°F) 4 per 37.78°C/100°F
425 - 650°C (800 - 1200°F) 2 per 37.78°C/100°F
650°C - FBP (1200°F - FBP) 1 per 37.78°C/100°F

• User Ranges. You specify the boiling point ranges and the
number of cuts per range.

Cutting the Assay

Once the Assay has been calculated, you can cut the Assay into
individual hypocomponents.

1. Move to the Cut/Blend tab of the Oil Characterization view. Click the
Add button to create a new Blend.
2. In the Name cell, change the name from the default, Blend-1 to Res-
Fluid.
3. From the list of Available Assays (there should only be one), select
Res-Fluid and click the Add button. This adds the Assay to the Oil
Flow Information table and a blend (cut) will automatically be
Note that reducing the calculated. The Blend is calculated using the default Cut Option,
Number of Cuts will
increase simulation speed,
Auto Cut.
but it may have a negative 4. Instead of using the default Auto Cut option, change the Cut Option
effect on simulation
accuracy.
Selection to User Points and change the Number of Cuts to 5.

The results of the calculation can be viewed on the Tables tab of the
Blend view.

12
 Oil Characterization 13

Installing the Oil in the Flowsheet

The final step of the characterization is to transfer the hypocomponent
information into the flowsheet.

1. Move to the Install Oil tab of the Oil Characterization view. The
blend, Res-Fluid appears in the Oil Install Information group.
2. In the Stream Name column, enter the name, GasWell 4, to which
the oil composition will be transferred.

HYSYS will assign the composition of your calculated Oil and Light Ends
into this stream, completing the characterization process.

Return to the Basis Environment by clicking the Return to Basis

Environment button.

When you return to the Basis Environment, the hypocomponents that

you have generated in the Oil Characterization are placed in the current
fluid package. You can view the fluid package and examine the
individual hypothetical components which make up your oil.

Save your case!

13
14 Oil Characterization

Analyzing the Results

Once you have calculated a blend, you can examine various property
and flow summaries for the generated hypocomponents that represent
a calculated oil.

Return to the Oil Environment and open the view for the blend, Res-
Fluid.

Tables Tab
The Tables tab of the blend contains various information, representing
the oil and the components. From the Table Type drop down, you can
select different information to display.

• Component Properties. When this is selected, choose either

Main Properties or Other Properties from the Table Control.
• Main Properties. Provides the normal boiling point,
molecular weight, density, and viscosity information for each
component in the oil.
• Other Properties. Provides the critical temperature, critical
pressure, acentric factor, and Watson K Factor for each
individual hypocomponent.
• Component Breakdown. For the input light ends and each
hypocomponent, this provides individual liquid volume %,
cumulative liquid volume %, volume, mass, and mole flows.
• Molar Compositions. Provides the molar fractions of each light
ends component and each hypocomponent in the oil.
• Oil Properties. Choose the Basis (Mole, Mass, Liquid Volume)
and then the property you want to display.
• Boiling Points. Provides TBP, D86, D86 Corr, D1160 Vac, and
D1160 Atm temperature ranges for the oil.
• Other Properties. Provides critical temperature, critical pressure,
acentric factor, molecular weight, density, and viscosity ranges for
the oil.
• User Properties. Provides all user property ranges for the oil.
• Oil Distributions. Provides tabular information of how your assay
would be distributed in a fractionation column. You can use
standard fractionation cuts or user defined cuts.

14
 Oil Characterization 15

Property Plot Tab

HYSYS can plot various properties versus liquid volume, mole, or mass
percent distilled.

Figure 3

From the Basis drop-down list, choose Mass, Mole, or Liquid Volume for
the X-Axis.

From the Property drop-down list, choose the property to be plotted on

the Y-axis.

• Distillation. You can plot one or more of the following: TBP, D86,
D86 (Crack Reduced), D1160 (Vac), D1160 (Atm), or D2887.
• Molecular Weight
• Density
• Viscosity
• Critical Temperature
• Critical Pressure
• Acentric Factor
• User Properties

15
16 Oil Characterization

Composite Plot Tab

The Composite Plot tab allows you to visually check the match between
Input assay data is only the input assay data and the calculated property curves. The choice for
displayed for distillation the graphical comparison is made from the Property drop-down list.
assay input and not for
chromatographic input.
• TBP or ASTM Distillation Curve
• Molecular Weight Curves
• Mass Density Curves
• Viscosity Curves
• Any User Property Curve

Viewing the Stream in the Simulation

1. Leave the Oil Environment to return to the Basis Environment.
2. Enter the Simulation Environment.
3. Move to the Workbook to view the stream that you created, GasWell
4. You can view the stream composition on the Compositions tab.

If you determine that some of the hypocomponents parameters need to

be recalculated, you can return to the Oil Environment at any time to
make changes.

The following parameters need to be added to the stream GasWell 4:

In this cell... Enter...

Temperature 35°C (95°F)
Flowrate 545 kgmole/h (1200 lbmole/hr)

Save your case!

16