Hongkong Marida Industry Co.,Limited: TEST Report

HONGKONG MARIDA
INDUSTRY CO.,LIMITED
TEST Report
REPORT NUMBER
170704008SHF-BP-1
ISSUE DATE
2017/9/26
PAGES
26
DOCUMENT CONTROL NUMBER

LFT-APAC-SHF-OP-10a
© 2017 INTERTEK
HONGKONG MARIDA INDUSTRY CO.,LIMITED
15B, 15/F CHEUK NANG PLAZA 250 HENNESSY ROAD, HONG KONG
Test Report
Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1
Applicant: HONGKONG MARIDA INDUSTRY CO.,LIMITED
Applicant Address: 15B, 15/F CHEUK NANG PLAZA 250 HENNESSY ROAD, HONG KONG
Attn: Future
SUBJECT: Performance testing

Rigid-LVT (SPC) (3.2mm-6.0mm)
Dear Sir,
This test report for represents the results of our evaluation of the above referenced product(s) to the
requirements contained in the following standards:
TEST METHODS AND STANDARDS
Refer to the next following Pages.
SAMPLE ID MODEL SPECIFICATION

S170704008SHF.001~018 &
S170704008SHF.025
4.0×0.3mm /
S170818019SHF.002
S170918004SHF.001
SAMPLE RECEIEVED: 2017/6/27; 2017/8/28; 2017/9/14

TESTED FROM: 2017/7/4 TO 2017/9/26
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client.
Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any
party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the
Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in
writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself
does not imply that the material, product, or service is or has ever been under an Intertek certification program.
LFT-APAC-SHF-OP-10a Version: 1-September-2017
Page 2 of 26
Test Report
Test Items, Method and Results:
General requirements:
Characteristics Test results Verdict
Overall thickness (mm) 4.03 Pass
Length (mm) 1219.53
Pass
Width (mm) 225.03
Squareness (mm) 0.15 Pass
Staightness (mm/m) 0.08 Pass
Flatness length (%) 0.01 Pass
Flatness width (%) 0.02 Pass
Joint openings average value (mm) 0.03
Pass
Joint openings maximum value (mm) 0.04
Height differences average value (mm) 0.06
Pass
Height differences maximum value (mm) 0.08
Classification requirements:
Characteristics Test results Classification
Wear resistance (method A) 2100 cycles Class 33
Impact resistance (big ball) 1800 mm Class 34
Micro-scratch resistance MSR-A2; MSR-B1 Class 34
Castor chair resistance 25000 cycles Class 34
Effect of furniture leg no visible damage Class 34
Residual indentation 0.02 Class 34
Resistance to staining See page 12 Class 34
Swelling See page 13 Class 34
Locking strength See page 14 Class 34
Dimensional stability due to variation of temperature See page 15 Class 34
Level of use class:

Class Symbol Intensity of use
34 Commercial Very heavy
Note:
1. The classification scheme and use intensity symbols are described in EN ISO 10874:2012.
Page 3 of 26
Test Report
Test Item: Geometrical Characteristics

Test Method: ISO 24337:2006
Test Item Test Result Nominal value Test Requirement

Average value= 4.03 mm
△tavg ≤ 0.50 mm
Thickness △tavg = 0.03 mm 4.0 mm
tmax-tmin ≤ 0.50mm
tmax-tmin = 0.06 mm
Length 1220 mm △l ≤ 0.5 mm
Maximum △l = 0.50 mm
△Wavg ≤ 0.10 mm
Width △Wavg = 0.03 mm 225 mm
Wmax-Wmin ≤ 0.20 mm
Wmax-Wmin = 0.10 mm
Squareness qmax = 0.15 mm _ qmax ≤ 0.20 mm
Straightness Smax = 0.08 mm/m _ Smax ≤ 0.30 mm/m
Maximum single values:

fw, convex = 0.02 % fw, concave ≤ 0.15 %,
Flatness _ fw, convex ≤ 0.20 %
fl, concave ≤ 0.50 %,
fl, convex = 0.01 % fl, convex ≤ 1.00 %
Oavg = 0.03 mm Oavg ≤ 0.15 mm

Openings _
Omax = 0.04 mm Omax ≤ 0.20 mm
havg = 0.06 mm havg ≤ 0.10 mm
Height difference _
hmax = 0.08 mm hmax ≤ 0.15 mm
Note:
Sample received: 2017/6/27
Sample ID: S170704008SHF.001
Page 4 of 26
Test Report
Test Item: Wear Resistance, method A

Test Method: EN 13329:2016, Annex E
Results:
Parameter Specimen 1 Specimen 2 Specimen 3
Initial wear point (IP) value, cycles 2100 2000 2100
Average IP value, cycles 2100
Note:
Page 5 of 26
Test Report
Test Item: Impact Resistance (big ball)

Test Method: EN 13329:2006+A1:2008, Annex F
Results:
Drop height (mm) 1800
Note:
Page 6 of 26
Test Report
Test Item: Micro-Scratch Resistance

Test Method: EN 16094:2012, Procedure A and B
Precondition: At a temperature of (23±2) ℃ and relative humidity of (50±5) % for a minimum of 24h
Test Condition: At a temperature of(23±2) ℃ and relative humidity of (50±5) %
Results:
Procedure A
Specimen Gloss change (%)
1 30.1
2 30.0
3 26.2
Average value 29
Classification MSR-A2
Procedure B
Specimen Visual assessment Classification
1 No visible scratches MSR-B1
Average value No visible scratches MSR-B1
Note:
Classification of mean values of gloss change as per EN 16094 procedure A
Page 7 of 26
Test Report
Classification for visual assessment as per EN 16094 procedure B
Page 8 of 26
Test Report

Test Item: Castor Chair Resistance
Test Method: EN 425:2002
Precondition: At a temperature of (23±2) ℃ and relative humidity (50±5) % for a minimum of 24h
Test Condition: At a temperature range of 18 ℃ to 25 ℃
Test Cycles: 25000
Results:
Type of damage Observation
Delamination No
Opening of joints No
Cracks No
Note:
The test specimens were not taken apart after finished 25000 cycles for assessment required by client.
Test Photo:
Page 9 of 26
Test Report
Test Item: Effect of Furniture Leg

Type of Feet: Type 0 (mass: 32 kg)
Test Speed: 0.20 m/s
Results:
X direction no visible damage
Y direction no visible damage
Note:
This test was conducted at the external approved facility, located at Guangzhou.
Test Photo:
Page 10 of 26
Test Report
Test Item: Residual Indentation

Test Method: EN ISO 24343-1:2012
Results:
Residual Indentation Result (mm)
Specimen 1 0.02
Specimen 2 0.03
Specimen 3 0.02
Average value 0.02
Note:
Page 11 of 26
Test Report
Test Item: Resistance to Staining

Test Method: EN 438-2:2005
Results:
Substance Duration of contact Resut of visual changes
Group 1: water 10 min 5
Group 1: acetone 10 min 5
Group 1: cleaning solution 10 min 5
Group 2: coffee 16 h 5
Group 3: sodium hydroxide (NaOH) 10 min 5
Group 3: hydrogen peroxide (H2O2) 10 min 5
Group 3: shoe polish 10 min 5
Index:
5: No visible change.
4: Slight change of gloss and/or colour, only visible at certain viewing angles.
3: Moderate change of gloss and/or colour.
2: Marked change of gloss and/or colour.
1: Surface distorion and/or blistering.
Note:
Page 12 of 26
Test Report
Test Item: Swelling

Results:
Parameter Result
Average thickness swelling in production direction (%) 0.20
Average thickness swelling in cross production direction (%) 0.10
Note:
The direction of tested specimen was showed as following.
Page 13 of 26
Test Report
Test Item: Locking Strength

Results:
Longitudinal joint
Parameter Average Result
Maximum locking strength Fmax (N) 1189
Specific locking strength (kN/m) 5.65
Locking strength at 0.2 mm joint opening F0.2 (N) 1085
Specific locking strength at 0.2 mm joint opening (kN/m) 5.16
Transverse joint
Parameter Average Result
Maximum locking strength Fmax (N) 1314
Specific locking strength (kN/m) 5.84
Locking strength at 0.2 mm joint opening F0.2 (N) 1229
Specific locking strength at 0.2 mm joint opening (kN/m) 5.46
Note:
Page 14 of 26
Test Report
Test Item: Dimensional Stability

Test Method: EN ISO 23999:2012
Results:
Parameter Result
Average dimensional change in production direction (%) 0.10
Average dimensional change in cross production direction (%) 0.05
Maximum dimensional change in production direction (%) 0.14
Maximum dimensional change in cross production direction (%) 0.06
Note:
A negative value indicates expansion, and a positive value indicates shrinkage.
Page 15 of 26
Test Report
Test Item: Toxic Elements Analysis

Test Method: With reference to European standard on safety of toys EN 71-3:1994+A1:2000/AC:2002,
acid extraction method was used and toxic elements content were determined by Inductively Coupled
Argon Plasma Spectrometry.
Test Item Test Result (mg/kg) Detection Limit (mg/kg) Limit (mg/kg)
Soluble Barium (Ba) ND 5 1000
Soluble Lead (Pb) ND 5 90
Soluble Cadmium (Cd) ND 5 75
Soluble Antimony (Sb) ND 5 60
Soluble Selenium (Se) ND 5 500
Soluble Chromium (Cr) ND 5 60
Soluble Mercury (Hg) ND 5 60
Soluble Arsenic (As) ND 2.5 25
Note:
mg/kg = milligram per kilogram
ND = Not detected (less than the detection limit)
Page 16 of 26
Test Report
Test Item: Phthalate content test

Test Method: With reference to EN 14372:2004, by Gas Chromatography-Mass Spectrometry (GC-MS)
analysis.
Tested compound Result (%, w/w) Limit (%,w/w) (Max.)
Di-butyl phthalate (DBP) ND ---
Di(2-ethyl hexyl) phthalate(DEHP) ND ---
Benzyl butyl phthalate (BBP) ND ---
Sum of three phthalates ND 0.1
Di-iso-nonyl phthalate (DINP) ND ---
Di-n-octyl phthalate (DNOP) ND ---
Di-iso-decyl phthalate (DIDP) ND ---
Sum of three phthalates ND 0.1
Note:
The above limit was quoted according to Annex XVII items 51 & 52 of the REACH regulation (EC)
NO.1907/2006 & Amendment NO.552/2009 for phthalate content in toys and children care articles.
Detection limit = 0.01% (w/w)
ND = Not detected
Page 17 of 26
Test Report
Test Item: Formaldehyde content test

Test Method: With reference to EN 717-1:2004 chamber method, formaldehyde content was detected by
UV-VIS spectrophotometer.
Test condition:
Chamber type: 1 m3 stainless steel chamber
Climatic conditions: 23℃, 45% R.H.
-1
Air exchange rate: 1.0 h
Loading factor: 1.0 m2/m3
Test duration: 240 hours
Test result: ND
Note:
3
mg/m = milligram per cubic meter
3
Detection limit = 0.02 mg/m
ND = Not Detected
Page 18 of 26
Test Report
Test Item: Thermal Conductivity & Resistance
Sample Specification: 300 mm (length) x 300 mm (width) x 4 mm (thickness)
Test Results:
Mean Temperature Thermal Thermal
Thickness
Sample Temperature Difference Resistance Conductivity
2
(mm) (℃) (℃) (m ·K)/W (W/m·K)
1 4.18 24.9 12.3 0.033 0.126
2 4.39 24.9 12.4 0.034 0.129
3 4.32 24.9 12.3 0.032 0.137
Average 4.30 25 12 0.033 0.130
Note:
Page 19 of 26
Test Report
Test Item Test Method Test Result

3
Density EN ISO 23996:2012 Mean: 1.958 g/cm
Note:
Page 20 of 26
Test Report
Test Items Test Method Test Results

Exposure time (h): 200h
Resistance to ISO 4892-2: 2013,
△E*= 0.58
artificial weathering cycle 1
Grey Sale= 4-5
Note:
Page 21 of 26
Test Report
Test Item Test Method Test Result

Dynamic coefficient of friction EN 13893:2002 0.30
Note:
Page 22 of 26
Test Report
Test items Test methods Test results
Mean value:
Peel resistance ISO 24345:2006 MD: 110 N/50mm
AMD: 105 N/50mm
Note:
Page 23 of 26
Test Report
Test items Test methods Test results

ISO 105-B02:2014
Colour fastness to artificial light Exposure Cycle A1, Method 3, Above Grade 6
Xenon-arc lamp
Note:
Page 24 of 26
Test Report
Test Items, Method and Results：
Test Item: Fungi resistance test

Test Method: ASTM G21-15 Standard Practice for Determining Resistance of Synthetic Polymeric
Materials to Fungi
Test organisms:
Aspergillus niger ATCC 9642, Penicillium pinophilum ATCC 11797, Chaetomium globosum ATCC 6205,
Aureobasidium pullulans ATCC 15233 and Gliocladium virens ATCC 9645.
Test condition(s): 28days, ＞85%RH, 28℃
Rating evaluation:
Rating Observed Growth on Specimens
0 None
1 Traces of growth (less than 10 %)
2 Light growth (10 to 30 %)
3 Medium growth (30 to 60 %)
4 Heavy growth (60 % to complete coverage)
Test result:
Evaluation Observed Growth on specimens
0 None
Note: This test was conducted at the external approved facility, located at Guangzhou.
Test Photo:
Page 25 of 26
Test Report
APPENDIX: SAMPLE RECEIVED PHOTO
Fig.1 Sample received on Fig.2 Sample received on Fig.2 Sample received on

2017/6/27 2017/8/28 2017/9/14
REPORT AUTHORIZED
When signed with physical or electronic signature, the contents of this report have been prepared and
approved per Intertek's quality process in accordance with ISO 17025.
Name: Sun Sun Name: Daniel Zhang Name: Evyn Cui

Title: Approver Title: Reviewer Title: Project Engineer
Revision:
NO. DATE CHANGES AUTHOR REVIEWER
170704008SHF-BP-1 2017/9/26 First issue Evyn Cui Daniel Zhang
Page 26 of 26

Hongkong Marida Industry Co.,Limited: TEST Report

Uploaded by

Copyright:

Available Formats

Hongkong Marida Industry Co.,Limited: TEST Report

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hongkong Marida Industry Co.,Limited: TEST Report

Uploaded by

Copyright:

Available Formats

HONGKONG MARIDA

DOCUMENT CONTROL NUMBER

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Applicant: HONGKONG MARIDA INDUSTRY CO.,LIMITED

SUBJECT: Performance testing

TEST METHODS AND STANDARDS

Refer to the next following Pages.

SAMPLE ID MODEL SPECIFICATION

SAMPLE RECEIEVED: 2017/6/27; 2017/8/28; 2017/9/14

LFT-APAC-SHF-OP-10a Version: 1-September-2017

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Level of use class:

34 Commercial Very heavy

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Geometrical Characteristics

Test Item Test Result Nominal value Test Requirement

Squareness qmax = 0.15 mm _ qmax ≤ 0.20 mm

Straightness Smax = 0.08 mm/m _ Smax ≤ 0.30 mm/m

Maximum single values:

Oavg = 0.03 mm Oavg ≤ 0.15 mm

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Wear Resistance, method A

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Impact Resistance (big ball)

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Micro-Scratch Resistance

Classification of mean values of gloss change as per EN 16094 procedure A

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Classification for visual assessment as per EN 16094 procedure B

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Effect of Furniture Leg

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Residual Indentation

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Resistance to Staining

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Swelling

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Locking Strength

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Dimensional Stability

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results:

Test Item: Toxic Elements Analysis

Issue Date: 2017/9/26 Intertek Report No. 170704008SHF-BP-1

Test Items, Method and Results: