Touch Advanced Display (TAD) Installation Guide: Applications
Touch Advanced Display (TAD) Installation Guide: Applications
Touch Advanced Display (TAD) Installation Guide: Applications
2020-11-06
Applications
The Touch Advanced Display (TAD) is a comprehensive
series of freely programmable operator interfaces
featuring both IP and MSTP BACnet ® communication
and graphic displays with a touch-screen interface. TAD
Displays feature thin-film-transistor widescreen (16:9)
displays of different sizes with a fully dimmable LED
backlight and resistive touch interface. The integrated
HTML 5.0 web server grants remote access whenever the
units are connected to an accessible IP network.
Note: The equipment is not intended for continuous
Installation exposure to direct sunlight as it accelerates the aging
process of the front panel film.
Observe these guidelines when installing the TAD:
Note: The equipment is not intended for installation
• Transport the display in the original container to in contact with corrosive chemical compounds. Check
minimize vibration and shock damage to the unit. the resistance of the front panel film to a specific
• Verify that all parts were shipped with the display. compound before installation.
• Do not drop the display or subject it to physical shock. Note: Do not use tools of any kind to operate the
touch screen of the panel.
Parts included
• One Touchscreen Advanced Display
• Mounting clips
• DC power connector
• One installation instructions sheet
Mounting
Mounting considerations
The design of the TAD series allows for multiple mounting
options including panel front and flush mounting on a
wall through utilization of the BOX0x-01 accessories. To
ensure the front panel protection classifications as marked
on the product nameplate, you must install the TAD on a
flat surface of a Type 2, 4X enclosure, tightening the fixing
brackets screws at 75Ncm for the appropriate cut-out:
• TAD0471-0: 136 mm x 96 mm (5.35 in. x 3.78 in.)
• TAD0701-0: 176 mm x 136 mm (6.90 in. x 5.35 in.)
• TAD1001-0: 271 mm x186 mm (10.66 in. x 7.32 in.)
If you wish to disregard the aforementioned front panel
protection classification, complete the steps found in
Mounting the TAD on a drywall or Mounting the TAD on a
masonry wall .
Mounting dimensions
Refer to the following illustrations for the mounting
dimensions and physical features of the TAD. Table 2: TAD mounting dimensions
Model A B C D
TAD0471- 107mm 147 mm 29 mm 5 mm
0 (4.21 in.) (5.78 in.) (1.14 in.) (0.19 in.)
TAD0701- 147 mm 187 mm 29 mm 5 mm
0 (5.79 in.) (7.36 in.) (1.14 in.) (0.19 in.)
TAD1001- 197 mm 282 mm 29 mm 6 mm
0 (7.75 in.) (11.10 in.) (1.14 in.) (0.23 in.)
CAUTION
ATTENTION
Accessories
Table 6: Serial port Table 8: Ordering codes
Pin Description Product code Description
1 GND BOX04-01 Wall mount box for TAD04
2 BOX07-01 Wall mount box for TAD07
3 TX/CHA- BOX10-01 Wall mount box for TAD10
4 RX/CHB- Counter display structure for
DEMO-STAND07
TAD07
5
DB-9 Serial Port Connector for
6 +5V output TAD-DB9-0
BACnet MSTP.
7 CTS/CHB+ Touchscreen Tailoring Tool, single
TTT0103
8 RTS/CHA+ license Key for 3 installations
9 Touchscreen Tailoring Tool, single
TTT0110
license Key for 10 installations
Note: You must connect pins 4-3 and pins 8-7 Touchscreen Tailoring Tool, single
TTT0130
externally to operate in RS485. license Key for 30 installations
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions
beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages
resulting from misapplication or misuse of its products.
Contact information
Contact your local branch office:
www.johnsoncontrols.com/locations
Contact Johnson Controls: www.johnsoncontrols.com/
contact-us
www.johnsoncontrols.com