Hempafloor Self-Level 200

Product Data Sheet
Hempafloor Self-level 200

Mix: 35834 Base: 35836. Curing Agent: 97814. Silica: 675ME.
(Formerly known as Strata Epoxy SL 2000)
Description: Hempafloor Self-level 200 is a self-smoothing, solvent-free three-component epoxy floor

coating system for a wide range of purpose.
Recommended use: Designed to protect concrete substrates where a seamless flooring surfaces combined with
excellent mechanical properties is essential. Ideal to a wide range of floors in warehouses,
factories, laboratories, kitchens, food processing industry and hygienic requirement
applications, etc. Can be applied up to 3 mm DFT.
Features: • Self-smoothing, seamless surface

• From 1 to 2 mm DFT
• Excellent chemical, abrasion and impact resistance
• Available in a wide range of colours
Certificates/approvals: Property Standard Result

Adhesion Strength ASTM D4541-09 4.8 N/mm2 (concrete failure)
Tensile Strength ASTM C307-03 (2012) 19 N/mm2
Flexural Strength ASTM C580-02 (2012) 42 N/mm2
Compressive Strength ASTM C579-01 (2012) 84 N/mm2
Abrasion Resistance ASTM D4060-10 59 mg/1000 cycles
Impact Resistance ASTM D2794 0.4 kg-m
Shore D Hardness ASTM D2240-05 (2010) D/83/1
Critical Radiant Flux ASTM E684 Class I
Chemical resistance Method Result

Distilled water (cold)
No discolouration, change in
Distilled water (hot)
gloss, blistering, softening,
Ethyl Alcohol (50%vol) ASTM
swelling, loss of adhesion or
Alkali solution (5%) D1308
special phenomena was
Soap solution
observed.
Detergent solution
Availability: Available in 15L (23 Kg). (Packing may vary from country to country depending on local requirements).
Physical constants*:
Colours/shade Nos.: According to Hempafloor Colour Card

Finish: High gloss
Volume solids, %: 100
Theoretical spreading rate: 3.1 kg/m² 2 mm DFT**
Flash point: >198°C
Specific gravity: 1.53 kg/litre
Dry to touch: 12 hours at 10°C 6 hours at 20°C 3 hours at 40°C
Initial hardness: 24 hours at 20°C
Fully cured: 7 days before the floor can be exposed to heavy duty traffic
VOC content: 34 g/litre
*The physical constants stated are nominal data according to the Hempel Group's approved formulas.
They are subject to normal manufacturing tolerances and where stated, being standard deviation
according to ISO 3534-1.
**The theoretical spreading rate has been calculated for the stated volume solids and dry film thickness. A
practical spreading rate will depend on the actual dry film thickness, the nature of the substrate and
relevant consumption factor. The physical constants are subject to normal manufacturing tolerances.
Further references can be found in the "Explanatory Notes".
Application details:
Mixing ratio: 36:18:46 by weight
Application method: Notched trowel, spin screed, spiked roller, spiked shoes
Thinner (max.vol.): Do not dilute
Pot life: 50 minutes at 20°C Reduced at higher temperature
Cleaning of tools: Hempel Tool Cleaner 99610
Indicated film thickness, dry: 1 x 1 – 2 mm
Indicated film thickness, wet: 1 x 1 – 2 mm
Overcoat interval, min: 48 hours at 10°C 24 hours at 20°C 12 hours at 40°C
Overcoat interval, max: 6 days at 10°C 72 hours at 20°C 36 hours at 40°C
Issued: November 2019 Page: 1/2

Product Data Sheet
Hempafloor Self-level 200
Mix: 35834 Base: 35836. Curing Agent: 97814. Silica: 675ME.
(Formerly known as Strata Epoxy SL 2000)
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint
containers, consult Hempel Material Safety Data Sheets and follow all local or national safety
regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take
precautions against possible risks of fire or explosions as well as protection of the
environment. Apply only in well ventilated areas.
Substrates: Concrete.
Application conditions: Use only where application and drying can proceed at temperatures above 5°C, preferably
above 10°C and relative humidity is below 75%. Other sealer/filler types may be specified.
Drying data given is on the assumption that proper ventilation is provided. Hempafloor Self-
level 200 should not be applied to concrete which contains more than 4% moisture.
Surface preparation: The surface should be stable, firm, dry and free from dust, sand, loose old paint, laitance, dirt,
grease and oil. Proper surface preparation is a must, mechanical surface preparation is highly
recommended.
Sealing/Priming: Hempafloor Prime 420 or Hempafloor Prime 100.
Filling: Hempafloor Fill 200. Recommendation: apply primer/sealer prior to the application of a
specified filler.
Mixing: Hempafloor Self-level 200 is a three component product, all components must be mixed
together before use. Stir the base (Part A) and continue stirring whilst adding all the contents of
the Curing agent (Part B) and mix until homogeneous. Then add the total contents of the silica
aggregates bag (Part C) while mixing. Mix all component 2-3 minutes till it reach a
homogeneous mixture. The use of a mechanical mixer is a must. No part mixing.
Application: 1. Pour the mixed Hempafloor Self-level 200 material onto the primed and sealed surface
and spread to the required thickness using a pin screed or notched trowel.
2. Immediately after laying the material to the required level, the applied material should be
rolled with a spiked roller to remove slight trowel marks, and to assist air release.
3. The rolling should be carried out using a ‘back and forth’ technique along the same path.
4. The rolling process should continue for a minimum of 5 times on the same path until all air
is released and a uniform colour is obtained, but it should be prior to setting of the product.
5. Operators should always wear a spiked shoes during the application to be able walk in the
wet material.
Storage & handling: Product must be stored as per local regulation. Keep in dry and ventilated location, far from
heat and direct sunlight.
Shelf-life: 12 months from date of production.
Remarks: Epoxy Epoxy coatings will yellow, chalk and lose gloss over a period of time when exposed to
direct or diffused sunlight. Yellowing is a surface phenomenon attributed to the chemical nature
of the resin with natural darkening. Degree of yellowing can vary from product to product but is
generally more obvious in pale shades. This has no influence on the function and performance
of the coating. For UV protection, we suggest you to apply a top coat of Hempafloor Durable
300 or consult Hempel for more suitable options.
Issued by: Hempel Middle East.
This Product Data Sheet supersedes those previously issued.

For explanations, definitions and scope see “Explanatory Notes” available on hempel.com. Data, specifications, directions and
recommendations given in this data sheet represent only test results or experience obtained under controlled or specially
defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the
Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to Hempel's general conditions of sales, delivery and
service, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all
claims involving, any liability, including but not limited to negligence, except as expressed in said general conditions for all
results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the
overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.
Issued: November 2019 Page: 2/2

Hempafloor Self-Level 200

Uploaded by

Copyright:

Available Formats

Hempafloor Self-Level 200

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hempafloor Self-Level 200

Uploaded by

Copyright:

Available Formats

Product Data Sheet

Hempafloor Self-level 200

Description: Hempafloor Self-level 200 is a self-smoothing, solvent-free three-component epoxy floor

Features: • Self-smoothing, seamless surface

Certificates/approvals: Property Standard Result

Chemical resistance Method Result

Colours/shade Nos.: According to Hempafloor Colour Card

Issued: November 2019 Page: 1/2

Sealing/Priming: Hempafloor Prime 420 or Hempafloor Prime 100.

Shelf-life: 12 months from date of production.

Issued by: Hempel Middle East.

This Product Data Sheet supersedes those previously issued.

Issued: November 2019 Page: 2/2

You might also like