Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 45 views

    Valve Analog Control: Instruments Automation Job Interview Quiz Blog More Courses

    Uploaded by

    zhangyili
    The document discusses modifying the control circuit of a Chinese actuator (M8300 series) to obtain a 4-20mA output for valve position and use it on an external remote screen. The actuator's circuit board is missing the "signal board" responsible for the 4-20mA output. The discussion considers making a custom signal board using the existing hall sensor circuit or trying to get feedback from other signals like open/close relays until the original signal board can be obtained from the vendor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Valve Analog Control: Instruments Automation Job Interview Quiz Blog More Courses

    Uploaded by

    zhangyili
    45 views3 pages
    The document discusses modifying the control circuit of a Chinese actuator (M8300 series) to obtain a 4-20mA output for valve position and use it on an external remote screen. The actuator's circuit board is missing the "signal board" responsible for the 4-20mA output. The discussion considers making a custom signal board using the existing hall sensor circuit or trying to get feedback from other signals like open/close relays until the original signal board can be obtained from the vendor.

    Original Title

    Valve analog control

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses modifying the control circuit of a Chinese actuator (M8300 series) to obtain a 4-20mA output for valve position and use it on an external remote screen. The actuator's circuit board is missing the "signal board" responsible for the 4-20mA output. The discussion considers making a custom signal board using the existing hall sensor circuit or trying to get feedback from other signals like open/close relays until the original signal board can be obtained from the vendor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    45 views3 pages

    Valve Analog Control: Instruments Automation Job Interview Quiz Blog More Courses

    Uploaded by

    zhangyili
    The document discusses modifying the control circuit of a Chinese actuator (M8300 series) to obtain a 4-20mA output for valve position and use it on an external remote screen. The actuator's circuit board is missing the "signal board" responsible for the 4-20mA output. The discussion considers making a custom signal board using the existing hall sensor circuit or trying to get feedback from other signals like open/close relays until the original signal board can be obtained from the vendor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Instruments Automation Job Interview Quiz Blog More Courses

    Valve analog control

    mohei_aldeen Oct '19

    hello there ,

    i’m having a trouble with an actuator (Chinese Actuator M8300 series)


    (http://www.cnzxq.com/products/Module/M8000/m8000_pcb.html ) this link
    is for the circuit description.

    the problem is that we need a (4-20ma) output from the actuator, and the
    board responsible for that didn’t come with the actuator. However, the actuator
    has a display screen that show the position of the valve in percentage .

    the question is : can i get use of modifying the control circuit so i can get the
    value of the position and use it in external remote screen ?

    i really wish that i can get an answer

    thank you very much .

    santhosh Oct '19

    Hi,

    As per the below statement, if you have “Hall Detection Board” then you can
    have the 4-20mA analog output for valve position status. We need to see this
    board configuration to confirm the same.

    M8000 intelligent electric actuator (M83, M84) control board (circuit


    board) is mainly composed of the following circuit boards: CPU board
    (main control board / computer board), signal board, power board (or filter
    board, filter board), The motor drive board (control board) is composed of
    a Hall detection board (also called a acquisition board for valve position
    detection and motor speed measurement) and a terminal block. The
    following describes the appearance and function of these boards:

    Make sure the existing display shows the real time valve position. sometimes,
    if you don’t have the required sensors/mechanism to read the valve feedback,
    the vendor may show command signal in percentage instead of real-time valve
    status.

    mohei_aldeen Oct '19

    thank you very much for replaying ,

    santhosh:

    the vendor may show command signal in percentage instead of real-time


    valve status

    i really don’t know if that is the case here , but we have the “drive board” that
    contain the hall sensor circuit .

    santhosh:

    you can have the 4-20mA analog output for valve position status
    but we don’t have the “signal board” that responsible for converting the sensor
    value to an analog 4-20ma signal .

    so do you suggest to make our own and connect it to the hall sensor circuit.?

    this is the “drive circuit / hall sensor circuit” that we have >>

    and again , i really thank you

    santhosh Oct '19

    If you have the hall sensor for valve feedback detection, then you need
    respective signal board.

    The signal board is responsible for completing the analog input and valve
    position feedback output function.

    We need datasheet of the boards or pin configuration for detailed analysis.

    Please request OEM to provide the details.


    Its better to use vendor provided circuit borads instead of custom-made/third-
    party circuits addition.

    Also, as some relays are availbale on the motor board, check for the
    availability of OPEN or CLOSE feedback signals atleast inplace of 4-20mA
    signal feedback, meanwhile you can try for the analog position feedback.

    mohei_aldeen Oct '19

    thank you sir ,

    i already check the digital auxiliary feed back output that should be found if
    the signal board is there ,unfortunately , the absence of the signal board has
    been confirmed .

    i well try to find a way to get the feedback while i’m trying to get the board
    from the vendor because the shipping will take a lot of time .

    thank you again

    ADVERTISEMENT

    You might also like