TD-40E Extra

CRAWLER DOZERS
EPA Tier 3 / EU Stage IIIA
STANDARD

ENGINE COOLING
TD-40E Extra TD-40E Extra
Make and model Cummins QSK19 Type Suction-type variable-speed fan,
hydraulically driven with perforated
Emissions standard EPA Tier 3/EU Stage IIIA engine side sheets and heavy-duty
Displacement 19 l (1150 in3) louvered front grill
Engine coolant rating –37 °C (–34 °F)
Bore and stroke 159 x 159 mm (6.25 in x 6.25 in)

Gross horsepower, SAE J1995 418 kW (560 hp)

Net horsepower, SAE J1349/ 384 kW (515 hp) OPERATOR STATION
ISO 9249
TD-40E Extra
Rated rpm 2000
ROPS ROPS (ISO 3471 - 2008)
Max. torque 2379 Nm (1,755 lb-ft)
FOPS FOPS (ISO 3449 - 2005)
Air cleaner 2-stage, dry type , with dash
mounted electronic service
indicator
Cold-starting aid ether start

Slope operation, max. angle 45 deg

HYDRAULICS UNDERCARRIAGE
TD-40E Extra
TD-40E Extra
Suspension Oscillation-type with equalizer bar
Type Open-center hydraulic system with and forward mounted pivot shafts
fixed-displacement multiple-pump Tracks Large deep-heat-treated, sealed,
vane type and lubricated track links and
Pump displacement 398 l/min (105 gpm) through-hardened, sealed, and
lubricated rollers for maximum
System relief pressure blade lift & ripper 17 MPa wear resistance
(2,400 psi)
blade tilt 18.4 MPa (2,670 psi) Track gauge 2500 mm (8 ft 2 in)

Control single joystick lever Track shoe width 610 mm (24 in)

Cylinders,bore and stroke Chain Sealed and lubricated

lift 152.4 x 1760 mm (6.0” x 69.3”)
Shoes, each side 39
tilt 254 x 175 mm (10” x 6.9”)
tilt/pitch 220 /254 x 175 mm (8.6”/10” x 6.9”) Track rollers, each side 7

Track length on ground 3610 mm (11 ft 10 in)

ELECTRICAL Ground contact area 44000 cm2 (6816 sq. in)

Ground pressure 151 kPa (21.9 psi)

TD-40E Extra
Voltage 24 V Track pitch 280 mm (11 in)

Number of batteries 4 Sprocket sements, each side 1

Battery capacity 960 CCA

Alternator rating 105 A

Lights 8 total; cab mounted (2F& 2R),

2F lift cylinders and 2R fuel tank
mounted
 MACHINE DIMENSIONS
TD-40E Extra
A Overall height - FOPS Cab 4,060 mm (13’ 10”)

A1 Overall height - ROPS 4,220 mm (13’ 10”)

A2 Overall height - end of 4,410 mm (14’ 6”)

exhaust pipe
B Grouser height 93 mm (3.66 in)

C Ground clearance 600 mm (23.7 in)

D Overall length, base machine 5,750 mm (18’ 10”)

D1 Length with blade 6.94 m (22 ft 9.4 in)

D2 Length with blade and 10.35 m / 9.76 m (34 ft /32 ft)

1-shank / 3-shank ripper
E Track length on ground 3,610 mm (11’ 10”)

F Width over track 3,110 mm (10’ 2”)

F1 Width over trunnions 3,730 mm (12’ 3”)

G Track gauge 2,500 mm (8’ 2”)

2
BLADE SPECS
TD-40E Extra
Type Semi-U Full-U Coal
SAE capacity 18.6 m³ (24.3 yd³) 22.8 m³ (29.8 yd³) 39.8 m³ (52 yd³)
H Blade height 2,230 mm (7’ 4”) 2,260 mm (7’ 5”) 2,500 mm (8’ 2”)
I Blade width 4,810 mm (15’ 9”) 5,180 mm (17’) 6850 mm (22’ 6”)
J Blade lift height 1,530 mm (5’ 0.2”) 1,530 mm (5’ 0.2”) 1,460 mm (4’ 9.5”)
K Blade angle - - -
L Blade digging depth 830 mm (32.7 in) 830 mm (32.7 in) 875 mm (34.4 in)
M Maximum tilt 1,150 mm (45.3 in) 1,250 mm (49.2 in) 1,650 mm (65 in)
N Maximum blade pitch adjustment 10° 10° 10°
O Overall width with blade angled - - -

RIPPER
TD-40E Extra
Type Parallelogram ripper with hydraulic pitch adjustment
Single-shank Single-shank Multi-shank
(Standard) (Deep Dig) (3-shank)
R Maximum clearance under tip (raised) 1,000 mm (39 in) 720 mm (28 in) 950 mm (37 in)
S Overall beam width 1,670 mm (65.7 in) 1,670 mm (65.7 in) 2,880 mm (113.5 in)
T Slope angle (full raise) 30.8° 30.8° 30.8°
U Ripping width - - 2,380 mm (94 in)
V Spacing center to center - - 1,190 mm (47 in)
X Maximum penetration 1,290 mm (51 in) 1,670 mm (66 in) 1,000 mm (39 in)
Z Maximum pitch adjustement 25.1° 25.1° 25.1°
Penetration force 200 kN (44,960 lb) 200 kN (44,960 lb) 205 kN (46,084 lb)
Pryout force 612 kN (137,578 lb) 612 kN (137,578 lb) 622.5 kN (139,938 lb)
Shank positions (vertical) 4 4 2
Weight of ripper incl. shank(s) 8,356 kg (18,422 lb) 8,461 kg (18,653 lb) 8,728 kg (19,242 lb)
Weight of shank 668 kg (1,473 lb) 773 kg (1,704 lb) 570 kg (1,260 lb)

OPERATING WEIGHTS SERVICEABILITY

TD-40E Extra TD-40E Extra
Base weight with Semi-U blade 67700 kg (149251 lb) Refill capacities
w/tilt, single-shank ripper,
standard equipment, cab ROPS/ Fuel tank 1362 l (360 US gal)
FOPS, full fuel tank, and 79 kg Cooling system 89.5 l (23.6 US gal)
[175 lb] operator)
Engine oil 59.3 l (15.7 US gal)
Optional components
Transmission system 270 l (71 US gal)
Ripper w/3 shanks + 372 kg (820 lb)
Final drive, each side 85 l (22.5 US gal)
Track shoes
Hydraulic reservoir 184 l (48.6 US gal)
660 mm (26 in) + 335 kg (740 lb)
3
800 mm (31.5 in) + 920 kg (2030 lb)
 Travel speeds
POWERTRAIN Gear Range Forward Reverse
TD-40E Extra
km/h (mph) km/h (mph)
Transmission Single stage 432 mm (17 in)
1st Low 3.2 (2.0) 4.1 (2.5)
torque converter with a 2.3:1
stall ratio drives to transmission High 4.1 (2.5) 5.2 (3.2)
through a double universal
joint. Modular, countershaft type 2nd Low 5.2 (3.2) 6.5 (4.0)
power shift transmission, electro-
High 6.7 (4.2) 8.4 (5.2)
hydraulic control. Preset travel
speed and auto-downshift. 3rd Low 9.4 (5.8) 11.7 (7.3)
Steering Exclusive 2-speed geared steering High 12.0 (7.5) 14.9 (9.3)
module provides gradual turns
while maintaining full power to Maximum 1157 kN (261041 lb)
both tracks, plus conventional drawbar pull
clutch-brake performance for tight Brakes
or pivot turns. Coupled to 3-speed
transmission, the 2-speed steering Service Spring applied hydraulically
provides 6 forward and 6 reverse released multi-disc wet brakes.
speeds. The left hand joystick Foot pedal piloted control.
controls transmission and steering Parking The steering brakes also
drive for up and down gearshifting, act as service and parking
steering, high/low selection and brakes. Service brakes are
LH/RH gradual turn. locked automatically when the
Final drives Double-reduction planetary transmission safety lever is
type final drives mounted actuated or when the engine is
independently of track frames and cut off.
dozer push arms for isolation from
shock loads
Total ratio 28.1 to 1

× 1000 lb 270 1200 kN

260

250 1100
240

230
1000
220
1st LOW
210
900
200

190

180 800

170
1st HIGH
160 700
150

140
600
130

120 2nd LOW

500
110

100

90 400

80

70 300
2nd HIGH
60

50
200
40
3rd LOW
30
100
20 3rd HIGH

10

1 2 3 4 5 6 7 8 9 10 11 12 13 14 km/h

1 2 3 4 5 6 7 8 9 mph
4
 STANDARD EQUIPMENT TD-40E Extra
ENGINE INSTRUMENTATION
Engine, Cummins QSK19, Tier 3, emission certified turbocharged, Gauges: fuel level, engine coolant temperature, engine oil pressure,
direct start, direct injection, 384 kW (515 fwhp) drive train system oil temperature, voltmeter, hourmeter, tachometer
Air cleaner, dry type with exhaust aspirated primary, safety elements Engine ECM failure warning lights and switches
and service indicator Gear, range, drive train and engine diagnostic display
Antifreeze, -34°F (-37°C) Warning lights: air cleaner filter, drive train oil filters, hydraulic
Cooling module; includes radiator, transmission oil cooler, hydraulic oil filters, transmission/clutch oil low pressure, coolant high
oil/fan drive oil cooler, fuel cooler, charge air cooler (CAC); isolation temperature, drive train oil high tempertature, fan drive oil filter
mounted Audible and visual warning system: low engine coolant level, low
Coolant filter conditioner engine oil pressure
Exhaust, resonator with elbow
ELECTRICAL
Fan, hydraulically driven, suction type, variable speed
Alarm, back-up
Filters, engine oil, full flow and by-pass with replaceable “spin-on”
elements Alternator 105 A
Fuel strainer Batteries, (4) 12 V, 1920 CCA, maintenance free, cold start
Muffler, under engine hood, insulated Horn, electric
Water separator, fuel system Lights for cab, 2 front, 2 rear
Lights with guards, 2 front - lift cylinders mounted, 2 rear - fuel tank
DRIVETRAIN mounted
Torque converter, single stage Receptacle, charging
Transmission, power shift, 3 speeds forward, 3 reverse, combined Starting, 24 V
with 2 speed steering provides 6 speeds forward, 6 reverse, preset
travel speed selection and auto-downshift UNDERCARRIAGE
Steering, planetary type, 2 speed, left hand single lever control Track adjusters, hydraulic
(joystick) Track chain guides, integral
Filters, power train, equipment hydraulics, “spin-on” micro glass type Track chain, sealed and lubricated (LTS) with split master link, 39
Brakes, foot, spring applied, hydraulically released links
Decelerator - right foot pedal, and brake - center foot pedal Track frame, 7 roller, 2500 mm (98”) gauge, oscillating type, lifespan
lubricated rollers and idlers
OPERATOR’S ENVIRONMENT Track shoes, 610 mm (24”) severe service, grouser type
Air conditioner/heater/pressurizer/defroster, underseat mounted;
behind roof mounted A/C condenser GUARDS
AM/FM radio ready Guards: crankcase (hinged) with front pull hook, transmission, fan,
Cab with 2 post ROPS, with sound suppression, 4 wipers w/ radiator and sprocket rock and dirt deflector
washers, inside mirror, dome light, tinted safety glass and air Engine hood, solid, sloped, partially perforated
recirculation system (approved according to ROPS - SAE J1040 and Engine side doors, hinged, partially perforated
FOPS - SAE J231)
Final drive seal guard
Seat, air suspension type, fabric cover, adjustable with arm rests,
swivel 14° to right Radiator guard doors, louvered, two-piece, hinged

Seat belt (SAE J386) - 3” wide, retactable

HYDRAULIC CONTROLS
Sun visor, front cab window
Hydraulic control, 3-spool, 1 lever with pilot operated blade control
Tools compartment (lift/tilt), ready for ripper

OTHER STANDARD EQUIPMENT

Cylinders, lift, with quick drop valve
Diagnostic centers for power train and equipment hydraulic pressures
Drawbar, fixed counterweight, 2900 kg (6400 lbs)
Ecological drains for engine oil, radiator coolant and hydraulic oil
Manuals, parts and operator’s
Rear operator platform

5
 OPTIONAL EQUIPMENT TD-40E Extra
BLADE EQUIPMENT GUARDS
Semi-U, 18.6 m³ (24.3 yd³), complete with all blade components, Final drive rock guard
includes hydraulic tilt and manual pitch or hyraulic tilt/pitch; blade Track roller guard
includes full width wear liner package
Transmission & engine crankcase guards, severe service
Full-U, 22.8 m³ (29.8 yd³), complete with all blade components,
includes hydraulic tilt ADDITIONAL OPTIONS
and manual pitch or hyraulic tilt/pitch; blade includes full width wear
liner package Inspection lamp, 24 V, portable, with 6 m (20’) cable

Coal Dozer, 39.8 m³ (52 yd³), complete with all blade components, Ether start
includes hydraulic tilt and manual pitch or hyraulic tilt/pitch Fast fill - engine crankcase
Fast fill - fuel tank
REAR MOUNTED EQUIPMENT Fast fill - hydraulic oil reservoir
Standard drawbar with additional counterweights additional 4 plates, Fast fill - power train oil reservoir
3945 kg (8690 lbs)
Starting/charging receptacle plug assembly (required to jump start
Ripper, multi-shank beam, with three shanks partially mounted, with or charge batteries) with 15 ft cable
hydraulic pitch, includes deduct for standard drawbar
Vandalism protection, for use with cab or canopy
Ripper with hydraulic pitch, single-shank beam, standard dig, with
hydraulic pin puller and standard dig shank, partially mounted, Maintenance tool kit, 17 items in a metal box
includes deduct for standard drawbar Maintenance tool kit, 36 items in metal box
Ripper with hydraulic pitch, single-shank beam, deep dig,with 1000 h maintenance package (filters)
hydraulic pin puller and deep dig shank, partially mounted, includes 1500 h maintenance package (filters)
deduct for standard drawbar
2000 h maintenance package (filters)

TRACK SHOES Sound suppression package

Track rollers, heavy duty

EXPORT PACKING
660 mm (26”) shoes, severe service
Export packing, drive-on / drive-off, machine on the trailer
762 mm (30”) shoes, severe service
Export packing, drive-on / drive-off, machine on the railway wagon
800 mm (31.5”) shoes, severe service Cab disassembled, protected in box

OPERATOR’S ENVIRONMENT SFRs

Heater/pressurizer/defroster, cab without air conditioner (A/C) Air precleaner, turbine type (Enginaire), (sandy & dusty operating
For use with cab: conditions)
• Air recirculation system with MSHA filters, severe service Additional cab heating “AIRTRONIC”
• AM/FM CD radio Beacon light, rotating
• Defroster fans Centralized Lubricating System
• Mirrors, 2 pcs, exterior For machine with/without ripper

• Sun visors (2), additional Coolant heater (Eberspacher), with additional fuel tank

• Lights, 2 additional, ROPS mounted Fuel heater ‘Racor’

Canopy ROPS/FOPS Heating for standard Fleetguard fuel filter

Includes vinyl seat, operator platform covers and instrument panel Trimble Ready Option
guard Factory preinstalled hydraulics, harness and brackets for the Trimble
Grade Control System components

At Dressta we take pride in innovating to help our

customers to achieve more in the jobs they do.

Our dedicated team of application engineers can customize

designs, modify standard equipment and adapt attachments
for peak performance in specific application tasks,
Specifications may change from time to time and this brochure may not reflect
improving productivity and bottom line results.
the latest specifications. Photographs in this brochure may not reflect market
configuration. Please consult your dealer to confirm specifications and configurations.
Do you have a Special Feature Request? See how 6
Dressta can help you achieve more in the jobs you do. Dressta encourages safe worksites.
Please consult operator’s manual before use of any Dressta equipment.

info@dressta.com
www.dressta.com DR-SP-TD40E-T3-A4-11052017-ENG