TD-25M Extra

CRAWLER DOZERS
EPA Tier 3 / EU Stage IIIA
STANDARD

ENGINE COOLING
TD-25M Extra TD-25M Extra
Make and model Cummins QSX15 Type suction- type variable-speed fan,
hydraulically diven with perforated
Emissions standard EPA Tier 3/EU Stage IIIA engine side sheets and heavy duty
Displacement 15 l (912 in3) louvered front grill
Engine coolant rating –37 deg C (–34 deg F)
Bore and stroke 137 x 169 mm (5.39 x 6.65 in)

Gross horsepower, SAE J1995 280 kW (375 hp)

Net horsepower, SAE J1349 246 kW (330 hp) OPERATOR STATION
/ISO 9249
TD-25M Extra
Rated rpm 1800
ROPS ROPS (ISO 3471 - 2008)
Max. torque 1825 Nm (1346 lb-ft)
FOPS FOPS (ISO 3449 - 2005)
Air cleaner 2-stage, dry type , with dash
mounted electronic service
indicator
Cold-starting aid intake- mounted air -inlet grid hater

Slope operation, max. angle 45 deg

HYDRAULICS UNDERCARRIAGE
TD-25M Extra
TD-25M Extra
Suspension Oscillation-type with equalizer bar
Type Open-center hydraulic system with and forward mounted pivot shafts
fixed-displacement
Tracks Large deep-heat-treated, sealed,
multiple-pump vane type
and lubricated track links and
Pump displacement 313.5 l/min (82,8 gpm) through-hardened, sealed, and
lubricated rollers for maximum
System relief pressure blade lift & ripper 17.2 MPa (2500 psi)
wear resistance
blade tilt 18.4 MPa (2670 psi)
Track gauge 2140 mm (7 ft)
Control single joystick lever
Track shoe width 560 mm (22 in)
Cylinders,bore and stroke
lift 127 x 1460 mm (5.0” x 57.5”) Chain Sealed and lubricated
tilt 200 x 130 mm (7.9” x 5.1”)
tilt/pitch 185 /200 x 130 mm (7.3”/7.9” x 5.1”) Shoes, each side 38

Track rollers, each side 7

Track length on ground 3150 mm (10 ft 4 in)

ELECTRICAL Ground contact area 35000 cm2 (5456 sq. in)
TD-25M Extra
Ground pressure 100 kPa (14.6 psi)
Voltage 24 V
Track pitch 250 mm (9.86 in)
Number of batteries 4
Sprocket sements, each side 8
Battery capacity 960 CCA

Alternator rating 100 A

Lights 8 total; cab mounted (2F& 2R),

2F lift cylinders and 2R fuel tank
mounted
MACHINE DIMENSIONS
TD-25M Extra
Type Semi-U Full-U Angle Coal
A Overall height - FOPS Cab 3670 mm (12 ft) 3670 mm (12 ft) 3670 mm (12 ft) 3670 mm (12 ft)
A1 Overall height - ROPS 3800 mm (12 ft 6 in) 3800 mm (12 ft 6 in) 3800 mm (12 ft 6 in) 3800 mm (12 ft 6 in)
A2 Overall height 3930 mm (12 ft 11 in) 3930 mm (12 ft 11 in) 3930 mm (12 ft 11 in) 3930 mm (12 ft 11 in)
- end of exhaust pipe
B Grouser height 76 mm (3 in) 76 mm (3 in) 76 mm (3 in) 76 mm (3 in)
C Ground clearance 575 mm (22.6 in) 575 mm (22.6 in) 575 mm (22.6 in) 575 mm (22.6 in)
D Overall length, base machine 5070 mm (16 ft 7 in) 5070 mm (16 ft 7 in) 5070 mm (16 ft 7 in) 5070 mm (16 ft 7 in)
D1 Length with blade and drawbar 6880 mm (22 ft 7 in) 7150 mm (23 ft 5 in) 6890 mm (22 ft 7 in) 7530 mm (24 ft 8 in)
D2 Length with blade and 1-shank / 8940 mm /8380 mm 9210 mm /8650 m 8950 m /8390 m 9030 mm (29 ft 8 in)
3-shank ripper (29 ft 4 in /27 ft 6 in) (29 ft 4 in /27 ft 6 in) (29 ft 4 in /27 ft 6 in)
E Track length on ground 3150 mm (10 ft 4 in) 3150 mm (10 ft 4 in) 3150 mm (10 ft 4 in) 3150 mm (10 ft 4 in)
F Width over track 2700 mm (8 ft 10 in) 2700 mm (8 ft 10 in) 2700 mm (8 ft 10 in) 2700 mm (8 ft 10 in)
F1 Width over trunnions 3210 mm (10 ft 6 in) 3210 mm (10 ft 6 in) 3210 mm (10 ft 6 in) 3210 mm (10 ft 6 in)
G Track gauge 2140 mm (7 ft) 2140 mm (7 ft) 2140 mm (7 ft) 2140 mm (7 ft)

2
BLADE SPECS
TD-25M Extra
Type Semi-U Full-U Angle Coal
SAE capacity 9.6 m3 (12.5 cu yd) 11.5 m3 (15.0 cu yd) 5.7 m3 (7.4 cu yd) 21.0 m3 (27.5 cu yd)
H Blade height 1760 mm (5 ft 9 in) 1760 mm (5 ft 9 in) 1260 mm (4 ft 1 in) 2100 mm (6 ft 11 in)
I Blade width 4050 mm (13 ft 3 in) 4350 mm (14 ft 3 in) 4950 mm (16 ft 3 in) 5610 mm (18 ft 5 in)
J Blade lift height 1270 mm (4 ft 2 in) 1270 mm (4 ft 2 in) 1370 mm (4 ft 6 in) 1270 mm (4 ft 2 in)
K Blade angle - - 25 deg -
L Blade digging depth 600 mm (23.6 in) 600 mm (23.6 in) 660 mm (26 in) 600 mm (23.6 in)
M Maximum tilt 880 mm (34.6 in) 945 mm (37.2 in) 435 mm (17.1 in) 1220 mm (48 in)
N Maximum blade pitch adjustment 10 deg 10 deg - 10 deg
O Overall width with blade angled - - 4,590 mm (15 ft 1 in) -

RIPPER
TD-25M Extra
Type Parallelogram ripper with hydraulic pitch adjustment
Single-shank Single-shank Multi-shank
(Standard) (Deep Dig) (3-shank)
R Maximum clearance under tip
770 mm (30.3 in) 760 mm (29.9 in) 868 mm (34.2 in)
(raised)
S Overall beam width 1450 mm (57 in) 1450 mm (57 in) 2485 mm (98 in)
T Slope angle (full raise) 30.8 deg 30.8 deg 30.8 deg
U Ripping width - - 2134 mm (84 in)
V Spacing center to center - - 1067 mm (42 in)
X Maximum penetration 1250 mm (49.2 in) 1700 mm (66.9 in) 760 mm (29.9 in)
Z Maximum pitch adjustement 25.1 deg 25.1 deg 25.1 deg
Penetration force 132.5 kN (29,768 lb) 132.5 kN (29,768 lb) 131.2 kN (29,494 lb)
Pryout force 377.7 kN (84,907 lb) 377.7 kN (84,907 lb) 353.5 kN (79,467 lb)
Shank positions (vertical) 4 6 2
Weight of ripper incl. shank(s) 5280 kg (11,630 lb) 5370 kg (11,840 lb) 5736 kg (12,646 lb)
Weight of shank 540 kg (1,190 lb) 634 kg (1,397 lb) 318 kg (700 lb)

OPERATING WEIGHTS SERVICEABILITY

TD-25M Extra TD-25M Extra
Base weight with Semi-U blade 41500 kg (91491 lb) Refill capacities
w/tilt, single-shank ripper,
standard equipment, cab ROPS/ Fuel tank 825 l (218 US gal)
FOPS, full fuel tank, and 79 kg Cooling system 56 l (15 US gal)
[175 lb] operator)
Engine oil 49 l (13 US gal)
Optional components
Transmission system 240 i (63 US gal)
Ripper w/3 shanks + 456 kg (1874 lb)
Final drive, each side 64 l (16.9 US gal)
Track shoes
Hydraulic reservoir 130 l (34 US gal)
610 mm (24 in) + 225 kg (495 lb)
AdBlue (DEF) 38 l (10 US gal) 3
660 mm (26 in) + 474 kg (1045 lb)

711 mm (28 in) + 655 kg (1445 lb)

POWERTRAIN
TD-25M Extra
Transmission Single stage 415 mm (16 in) Maximum 794 kN (178,498 lb)
torque converter with a 2.45:1 drawbar pull
stall ratio drives to transmission
Drawbar Pull - Speed 1 kN (lbf ) 791 (177824) -
through a double universal
1st Low
joint. Modular, countershaft type
power shift transmission, electro- Drawbar Pull - Speed 1 '000 kgf ('000 lbf) 80.66 (177.82) -
hydraulic control. Preset travel 1st Low
speed and auto-downshift Drawbar Pull - Speed 2 kN (lbf) 606 (136234) -
1st High
Steering Exclusive 2-speed geared steering
module provides gradual turns Drawbar Pull - Speed 2 '000 kgf ('000 lbf) 61.79 (136.23) -
while maintaining full power to 1st High
both tracks plus conventional Drawbar Pull - Speed 3 kN (lbf) 465 (104536) -
clutch-brake performance for tight 2nd Low
or pivot turns. Coupled to 3-speed
transmission, the 2-speed steering Drawbar Pull - Speed 3 '000 kgf ('000 lbf) 47.42 (104.53) -
provides 6 speeds forward and 2nd Low
6 reverse. The left hand joystick Drawbar Pull - Speed 4 kN (lbf) 344 (77334) -
controls transmission and steering 2nd High
drive for up and down shifting,
Drawbar Pull - Speed 4 '000 kgf ('000 lbf) 35.08 (77.33) -
steering, Hi/Lo selection and LH/
2nd High
RH gradual turn.
Drawbar Pull - Speed 5 kN (lbf) 281 (63171) -
Final drives Double-reduction planetary
3rd Low
type final drives mounted
independently of track frames and Drawbar Pull - Speed 5 '000 kgf ('000 lbf) 28.65 (63.17) -
dozer push arms for isolation from 3rd Low
shock loads Drawbar Pull - Speed 6 kN (lbf) 207 (46535) -
Total ratio 25.5 to 1 3rd High
Drawbar Pull - Speed 6 '000 kgf ('000 lbf) 21.11 (46.53) -
Travel speeds
3rd High
Range Forward Reverse Brakes
1st Low 3.0 km/h 3.7 km/h Service Spring applied hydraulically
(1.9 mph) (2.3 mph) released multi-disc wet brakes.
High 3.9 km/h 4.7 km/h Foot pedal piloted control
(2.4 mph) (2.9 mph) Parking The steering brakes also
2nd Low 5.1 km/h 6.1 km/h act as service and parking
(3.2 mph) (3.8 mph) brakes. Service brakes are
locked automatically when the
High 6.6 km/h 7.9 km/h
transmission safety lever is
(4.1 mph) (4.9 mph)
actuated or when the engine is
3rd Low 8.0 km/h 9.6 km/h cut off.
(5.0 mph) (6.0 mph)
High 10.3 km/h 12.3 km/h
(6.4 mph) (7.6 mph)

4
 STANDARD EQUIPMENT TD-25M Extra
ENGINE INSTRUMENTATION
Engine, Cummins QSX15, Tier 3, emission certified,turbocharged, Engine ECM failure warning lights and switches
direct start, direct injection, 246 kW (330 fwhp) Gear, range, drive train and engine diagnostic display
Air cleaner, dry type with exhaust aspirated primary,safety elements Gauges: fuel level, engine coolant temperature, engine oil pressure,
and service indicator torque converter oil temperature, voltmeter, hourmeter, tachometer
Antifreeze, -34°F (-37°C) Warning lights: air cleaner filter, transmission oil filters, hydraulic
Cooling module; includes radiator, transmission oil cooler, hydraulic oil filters, transmission/clutch oil low pressure, coolant high
oil/fan drive oil cooler, fuel cooler, charge air cooler (CAC); isolation temperature, drive train oil high tempertature, fan drive oil filter
mounted Audible and visual warning system: low engine coolant level, low
Coolant filter conditioner engine oil pressure
Exhaust resonator with elbow
ELECTRICAL
Fan, hydraulically driven, suction type, variable speed
Alarm, back-up
Filters, engine oil, full flow and by-pass with replaceable “spin-on”
elements Alternator 110 A
Fuel strainer Batteries (4) 12 V, 1920 CCA, cold start, maintenance free
Muffler, under engine hood, insulated Horn, electric
Water separator, fuel system Lights for cab, 2 front, 2 rear
Lights with guards, 2 front - lift cylinders mounted, 2 rear - fuel tank
DRIVETRAIN mounted
Torque converter, single stage Portable lamp receptacle, 12 V
Transmission, power shift, 3 speeds forward, 3 reverse, combined Receptacle, starting/charging plug
with 2 speed steering provides 6 speeds forward, 6 reverse, preset
Starting, 24 V
travel speed selection and auto-downshift
Starting aid - air grid heater
Steering, planetary type, 2 speed, left hand single lever control (joystick)
Filters, power train, equipment hydraulics, “spin-on” micro glass type UNDERCARRIAGE
Brakes, foot, spring applied, hydraulically released Track adjusters, hydraulic
Decelerator - right foot pedal, and brake - center foot pedal Track chain, sealed and lubricated (LTS) with split master link, 38
links
OPERATOR’S ENVIRONMENT
Track chain guides, integral
Air conditioner/heater/pressurizer/defroster, underseat mounted;
Track frame, 7 roller, 2140 mm (84”) gauge, oscillating type, lifespan
behind roof mounted A/C condenser
lubricated rollers and idlers
AM/FM radio ready
Track shoes, 560 mm (22”), grouser type
Cab with 2 post ROPS, with sound suppression, 4 wipers w/washers,
inside mirror, dome light, tinted safety glass and air recirculation GUARDS
system (approved according to ROPS - SAE J1040 and FOPS - SAE Crankcase, hinged, with front pull hook, transmission, fan, radiator,
J231) sprocket rock and dirt deflector
Seat, air suspension type, fabric cover, adjustable with arm rests, Engine hood, solid, sloped
swivel 14° to right Engine side doors, hinged, perforated type
Seat belt (SAE J386) - 3” wide, retactable Final drive seal guard
Sun visor for front cab window Radiator guard doors, louvered, two-piece, hinged
Tools compartment
HYDRAULIC CONTROLS
3-spool valve, 1 lever with pilot operated blade control (lift/tilt), ready
for ripper

OTHER STANDARD EQUIPMENT

Cylinders, lift, with quick drop valve
Diagnostic centers for power train and equipment hydraulic
pressures
Drawbar, fixed
Ecological drains for engine oil, radiator coolant and hydraulic oil
Manuals, parts and operator’s
Rear access platform
5
 OPTIONAL EQUIPMENT TD-25M Extra
BLADE EQUIPMENT SCREENS
Semi-U, 9.6 m³ (12.5 yd³), complete with all blade Sweeps, forestry, front and rear, for standard cab with ROPS or open
components, blade includes reinforced center push plate, with ROPS machine; include exhaust pipe extension with guard and guard
hydraulic tilt and manual pitch or hyraulic tilt/pitch for fuel tank and hydraulic reservoir
Full-U, 11.5 m³ (15 yd³), complete with all blade Screen, rear (required for winch application), for use with forestry
components, blade includes reinforced center push plate, with sweeps
hydraulic tilt and manual pitch or hyraulic tilt/pitch Screens for cab windows (front, rear, side, doors) bolted, black painted
Coal Dozer, 21.0 m³ (27.5 yd³), complete with all blade Screens for cab lights (2 front, 2 rear), black painted
components, blade includes reinforced center push plate, with Screens for tractor lights (2 front, 2 rear)
hydraulic tilt and manual pitch or hyraulic tilt/pitch Screens for ROPS mounted lights, (2 front)
Angle (manual angle), 5.7 m³ (7.4 yd³), complete with all blade
GUARDS
components, with or without hydraulic tilt
Final drive rock guard
REAR MOUNTED EQUIPMENT Track roller guards, full length
Drawbar, counterweight, 1860 kg (4100 lbs) Transmission and engine crankcase guards, severe service
Additional counterweight (cast), 2004 kg (4410 lbs); Engine hood, perforated
recommended for use with large coal or landfill blade Tank guard, bolted (0.5”” plate protects fuel tank and hydraulic
Ripper, multi-shank with three shanks, partially mounted, with reservoir)
hydraulic pitch, includes deduct for drawbar
Ripper single-shank beam, with hydraulic pitch, standard or deep ADDITIONAL OPTIONS
dig, with hydraulic pin puller and shank, partially mounted, includes Sound suppression package, for use with std solid hood or with
deduct for drawbar
perforated hood, includes sound suppressed radiator guard doors
TRACK SHOES Inspection lamp, 24 V, portable, with 6 m (20’) cable
610 mm (24”) shoes Starting/charging receptacle plug assembly (required to jump start
or charge batteries) with 15 ft cable
660 mm (26”) shoes, clipped corner
Vandalism protection for use with engine enclosures
711 mm (28”) shoes, clipped corner, (not recommended for use with
ripper) Maintenance tool kit, 17 items in a metal box
1000 h maintenance package (filters)
OPERATOR’S ENVIRONMENT 2000 h maintenance package (filters)
Heater/pressurizer/defroster, cab without air conditioner (A/C) 2000 h maintenance package (filters)
For use with cab: 4000 h maintenance package (filters)
Heater/pressurizer/defroster, cab without air conditioner (A/C)
For use with cab: EXPORT PACKING
• Air recirculation system with MSHA filters, severe service Export packing, drive-on/drive-off, machine on the trailer, cab crated
• AM/FM CD radio Export packing, drive-on/drive-off, machine on the railway wagon
• Mirrors, 2 pcs, exterior
SFRs
• Sun visors (2), additional, for side door windows
Centralized Lubricating System
• Lights, 2 additional, ROPS mounted
Trimble Ready Option, factory preinstalled hydraulics, harness and
• Lights, additional, ROPS mounted, 2 front, 2 rear or side
brackets for the Trimble Grade Control System components
Canopy ROPS/FOPS
Landfill Package for STD machine
Includes vinyl seat, operator platform covers, instrument panel guard
and lights, 2 front, 2 rear.
ROPS structure for use with sweeps
Includes vinyl seat, operator platform covers and instrument panel
guard

6
At Dressta we take pride in innovating to help our
customers to achieve more in the jobs they do.

Our dedicated team of application engineers can customize

designs, modify standard equipment and adapt attachments
for peak performance in specific application tasks,
improving productivity and bottom line results.

Do you have a Special Feature Request? See how

Dressta can help you achieve more in the jobs you do.

Specifications may change from time to time and this brochure may not reflect
the latest specifications. Photographs in this brochure may not reflect market
configuration. Please consult your dealer to confirm specifications and configurations.

Dressta encourages safe worksites.

Please consult operator’s manual before use of any Dressta equipment.

info@dressta.com
www.dressta.com DR-SP-TD25M-T3-A4-11052017-ENG