Search Keyword

AUTOMATION Search
Discontinued Sign In / Register
CONTROLS Products

Products Downloads Learn Our Products Support Pearls of Wisdom

Business > Industrial Devices > Automation Controls Top > Components & Devices > Relays / Couplers > Relays Cautions for Use English (Asia Pacific)

Relays Cautions for Use

CONTACT US
BY EMAIL
Please click your area to select
country or region

Asia-Pacific
Middle East
1. Method of Determining Specifications 6. Ambient Environment
Afghanistan GO
2. Precautions Regarding Coil Input 7. Environmentally Sealed Type Relays
3. Precautions Regarding Contact 8. Mounting Considerations
4. Precautions Regarding Latching Relays 9. Method of Mounting and Lead Wires Connection BY PHONE
5. Handling Cautions for Tube Packaging 10. Cautions for Use-Check List
Singapore +65-6390-3706
Here is PDF of this page.
India +91-124-4871300

A relay may be subjected to a variety of ambient conditions during actual use resulting in unexpected failure. Therefore, testing Indonesia +62-21-252-1616
over a practical range under actual operating conditions is necessary. Application considerations should be reviewed and Vietnam +84-2838130613
determined for proper use of the relay. -3004

SAFETY PRECAUTIONS Thailand +66-2-693-1870

Use that exceeds the specification ranges such as the coil rating, contact rating and switching life should be absolutely Malaysia +60-3-2297-6888
avoided. Doing so may lead to abnormal heating, smoke, and fire.
Philippines +632-886-6291
Never touch live parts when power is applied to the relay. Doing so may cause electrical shock. When installing, maintaining,
or troubleshooting a relay (including connecting parts such as terminals and sockets) be sure that the power is turned off. Turkey +90-216-681-0400
When connection terminals, please follow the internal connection diagrams in the catalog to ensure that connections are done Distributors in Asia-Pacific,
correctly. Be warned that an incorrect connection may lead to unexpected operation error, abnormal heating, and fire. Middle East
If the possibility exists that faulty adhesion or contact could endanger assets or human life, take double safety precautions and
make sure that operation is foolproof.
FAQ
1. Method of Determining Specifications

In order to use the relays properly, the characteristics of the selected relay should be well known, and the conditions of use of
the relay should be investigated to determine whether they are matched to the environmental conditions, and at the same time,
the coil conditions, contact conditions, and the ambient conditions for the relay that is actually used must be sufficiently known in RECOMMENDS
advance.
In the table below, a summary has been made of the points of consideration for relay selection. It may be used as a reference Introduction to
for investigation of items and points of caution. Automation
Specification item Consideration points regarding selection Controls

a) Rating
b) Pick-up voltage FEATURES
(current)
c) Drop-out voltage 1) Select relay with consideration for power source ripple.
(current) 2) Give sufficient consideration to ambient temperature, for the coil A Vital Piece
Coil d) Maximum continuous temperature rise and hot start. to the EV and
impressed voltage 3) When used in conjunction with semiconductors, additional attention to the HEV Puzzles
(current) application should be taken. Be careful of voltage drops when starting up.
e) Coil resistance
f) Impedance Energy
g) Temperature rise Management
Applications
1) It is desirable to use a standard product with more than the required number
of contacts.
2) It is beneficial to have the relay life balanced with the life of the device it is
Automotive
a) Contact arrangement used in.
Applications
b) Contact rating 3) Is the contact material matched to the type of load?
Contacts c) Contact material It is necessary to take care particularly with low level load.
d) Life 4) The rated life may become reduced when used at high temperatures.
e) Contactresistance Life should be verified in the actual atmosphere used.
5) Depending on the circuit, the relay drive may synchronize with the AC load.
As this will cause a drastic shortening of life should be verified with the actual
Search Relays
machine.
a) Operate time PhotoMOS
b) Release time 1) It is beneficial to make the bounce time short for sound circuits and similar Use MOSFETs in output
Operate time
c) Bounce time applications. elements.
d) Switching frequency Semiconductor relay for
AC and DC load
a) Vibration resistance 1) Give consideration to performance under vibration and shock in the use control.
Mechanical b) Shock resistance location.
characteristics c) Ambient temperature 2) A relay that uses insulated copper wire of high heat resistance if it will be Power Relays
d) Life used in a particularly high temperature environment. (Over 2A)
Mechanical relay with
1) Selection can be made for connection method with plug-in type, printed greater than 2A nominal
a) Breakdown voltage circuit board type, soldering, tab terminals, and screw fastening type. switching capacity that
is ideal for power supply
b) Mounting method 2) For use in an adverse atmosphere, sealed construction type should be
Other items applications.
c) Size selected.
d) Protective construction 3) When used in adverse environments, use the sealed type. 4) Are there any Safety Relays
special conditions? Safety relay ideal for
safety circuit
construction , with
Basics on Relay Handling forcibly guided contact
To maintain initial performance, care should be taken to avoid dropping or hitting the relay. structure.

Under normal use, the relay is designed so that the case will not detach. To maintain initial performance, the case should not
Solid State
be removed. Relay characteristics cannot be guaranteed if the case is removed.
Relays
Use of the relay in an atmosphere at standard temperature and humidity with minimal amounts of dust, SO2, H2S, or organic Semiconductor relay
gases is recommended. For installation in adverse environments, one of the sealed types should be considered. ideal for heater control,
etc. SSR (Solid State
Please avoid the use of silicon-based resins near the relay, because doing so may result in contact failure. (This applies to Relay)
plastic sealed type relays, too.)
When connecting coils of polarized relays, please check coil polarity (+, -) at the internal connection diagram (Schematic). If Signal Relays
any wrong connection is made, it may cause unexpected malfunction, like abnormal heat, fire and so on, and circuit do not (2A or less)
work. Mechanical relay ideal
Avoid impressing voltages to the set coil and reset coil at the same time. for signal control, etc.,
with less than 2A
Proper usage requires that the rated voltage be impressed on the coil. Use rectangular waves for DC coils and sine waves for nominal switching
AC coils. capacity.
 Be sure the coil impressed voltage does not continuously exceed the maximum allowable voltage. Microwave
The rated switching power and life are given only as guides. The physical phenomena at the contacts and contact life greatly Devices
vary depending on the type of load and the operating conditions. Therefore, be sure to carefully check the type of load and Lineup spans from
operating conditions before use. relays to coaxial
switches. High-
Do not exceed the usable ambient temperature values listed in the catalog. frequency devices that
support high bandwidth
Use the flux-resistant type or sealed type if automatic soldering is to be used. frequencies.
Although the environmentally sealed type relay (plastic sealed type,etc.) can be cleaned, avoid immersing the relay into cold
liquid (such as cleaning solvent) immediately after soldering. Doing so may deteriorate the sealing performance. Automotive
Surface-mount terminal type relay is sealed type and it can be cleaned by immersion. Use pure water or alcohol-based Relays
cleaning solvent. Relays for automotive
Cleaning with the boiling method is recommended (The temperature of cleaning liquid should be 40°C or lower). Avoid electrics that includes
plug-in PCB type.
ultrasonic cleaning on relays. Use of ultrasonic cleaning may cause breaks in the coil or slight sticking of the contacts due to
the ultrasonic energy.
Control Panel
Avoid bending terminals, because it may cause malfunction. Relays
As a guide, use a Faston mounting pressure of 40 to 70N {4 to 7kgf}for relays with tab terminals. Relays for general
purpose switching
For proper use, read the main text for details. (Various types are
prepared for multiple
applications)
Return to top
High-capacity
DC Cutoff
2. Precautions Regarding Coil Input Relays
400 V DC high voltage
Application of the rated voltage is the most basic requirement for accurate relay operation. Although the relay will work if the switching possible. Up
to 300 A current
voltage applied exceeds the pick-up voltage, it is required that only the rated voltage be applied to the coil out of consideration capacity type available.
for changes in coil resistance, etc., due to differences in power supply type, voltage fluctuations, and rises in temperature.
Also, caution is required, because problems such as layer shorts and burnout in the coil may occur if the voltage applied Optical
exceeds the maximum that can be applied continuously. The following section contains precautions regarding coil input. Please Switches
refer to it in order to avoid problems. Optical switches that
make high-speed
1. Basic Precautions Regarding Coil optical communication
AC operation type switching possible.

For the operation of AC relays, the power source is almost always a commercial frequency (50 or 60Hz) with standard voltages
of 6, 12, 24, 48, 100, and 200V AC. Because of this, when the voltage is other than the standard voltage, the product is a
special order item, and the factors of price, delivery, and stability of characteristics may create inconveniences. To the extent Related Information
that it is possible, the standard voltages should be selected. FA Sensors & Components
Also, in the AC type, shading coil resistance loss, magnetic circuit eddy current loss, and hysteresis loss exit, and because of
lower coil efficiency, it is normal for the temperature rise to be greater than that for the DC type. Interface Terminal
Furthermore, because humming occurs when below the pick-up voltage and when above the rated voltage, care is required with
regard to power source voltage fluctuations. Technology
For example, in the case of motor starting, if the power source voltage drops, and during the humming of the relay, if it reverts to
the restored condition, the contacts suffer a burn damage and welding, with the occurrence of a false operation self-maintaining High capacity cut-off relay
condition. Optical devices R&D
For the AC type, there is an inrush current during the operation time (for the separated condition of the armature, the impedance
is low and a current greater than rated current flows; for the adhered condition of the armature, the impedance is high and the Service & Support
rated value of current flows), and because of this, for the case of several relays being used in parallel connection, it is necessary
to give consideration to power consumption. Discontinued Products
DC operation type RoHs Directive Agreement
For the operation of DC relays, standards exist for power source voltage and current, with DC voltage standards set at 5, 6, 12, Commodity retrieval
24, 48, and 100V, but with regard to current, the values as expressed in catalogs in milliamperes of pick-up current. Global Sales Network
However, because this value of pick-up current is nothing more than a guarantee of just barely moving the armature, the
variation in energizing voltage and resistance values ,and the increase in coil resistance due to temperature rise, must be given
consideration for the worst possible condition of relay operation, making it necessary to consider the current value as 1.5 to 2
times the pick-up current. Also, because of the extensive use of relays as limit devices in place of meters for both voltage and
current, and because of the gradual increase or decrease of current impressed on the coil causing possible delay in movement
of the contacts, there is the possibility that the designated control capacity may not be satisfied. Thus it is necessary to exercise
care. The DC type relay coil resistance varies due to ambient temperature as well as to its own heat generation to the extent of
about 0.4%/°C, and accordingly, if the temperature increases, because of the increase in pick-up and drop-out voltages, care is
required. (However, for some polarized relays, this rate of change is considerably smaller.)

2. Power Source for Coil Input

Energizing Voltage of AC Coil
In order to have stable operation of the relay, the energizing voltage should be basically within the range of +10%/-15% of the
rated voltage. However, it is necessary that the waveform of the voltage impressed on the coil be a sine wave. There is no
problem if the power source is commercially provided power, but when a stabilized AC power source is used, there is a
waveform distortion due to that equipment, and there is the possibility of abnormal overheating. By means of a shading coil for
the AC coil, humming is stopped, but with a distorted waveform, that function is not displayed. Fig. 1 below shows an example of
waveform distortion.
If the power source for the relay operating circuit is connected to the same line as motors, solenoids, transformers, and other
loads, when these loads operate, the line voltage drops, and because of this the relay contacts suffer the effect of vibration and
subsequent burn damage. In particular, if a small type transformer is used and its capacity has no margin of safety, when there
is long wiring, or in the case of household used or small sales shop use where the wiring is slender, it is necessary to take
precautions because of the normal voltage fluctuations combined with these other factors. When trouble develops, a survey of
the voltage situation should be made using a synchroscope or similar means, and the necessary counter-measures should be
taken, and together with this determine whether a special relay with suitable excitation characteristics should be used, or make a
change in the DC circuit as shown in Fig. 2 in which a capacitor is inserted to absorb the voltage fluctuations. In particular, when
a magnetic switch is being used, because the load becomes like that of a motor, depending upon the application, separation of
the operating circuit and power circuit should be tried and investigated.

Power Source for DC Input

We recommend that the voltage applied to both ends of the coil in DC type relays be within ±5% of the rated coil voltage.
As a power source for the DC type relay, a battery or either a half wave or full wave rectifier circuit with a smoothing capacitor is
used. The characteristics with regard to the excitation voltage of the relay will change depending upon the type of power source,
and because of this, in order to display stable characteristics, the most desirable method is perfect DC.
In the case of ripple included in the DC power source, particularly in the case of half wave rectifier circuit with a smoothing
capacitor, if the capacity of the capacitor is too small, due to the influence of the ripple, humming develops and an unsatisfactory
condition is produced.
With the actual circuit to be used, it is absolutely necessary to confirm the characteristics.
It is necessary to give consideration to the use of a DC power source with less than a 5% ripple. Also ordinarily the following
must be given thought.
1. For the hinge type relay, a half wave rectifier cannot be used, alone unless you use a smoothing capacitor. The ripple and
the characteristics must be evaluated for proper usage.
2. For the hinge type relay, there are certain applications that may or may not use the full wave rectifier on it's own. Please
check specifications with the original manufacture.
3. Coil applied voltage and the drop in voltage
Shown below it is a circuit driven by the same power supply (battery, etc.) for both the coil and contact.
Electrical life will be affected by the drop in voltage in the coil when load is turned on.
Please verify that the actual voltage is applied to the coil at the actual load.

3. Maximum Allowable Voltage and Temperature Rise

Proper usage requires that the rated coil voltage be impressed on the coil. Note, however, that if a voltage greater than or equal
to the maximum continuous voltage is impressed on the coil, the coil may burn or its layers short due to the temperature rise.
Furthermore, do not exceed the usable ambient temperature range listed in the catalog.
Maximum Continuous Voltage
In addition to being a requirement for relay operation stability, the maximum continuous impressed coil voltage is an important
constraint for the prevention of such problems as thermal deterioration or deformity of the insulation material, or the occurrence
of fire hazards.
In actual use with E-type insulation, when the ambient temperature is 40°C, a temperature rise limit of 80°C is thought to be
reasonable according to the resistance method. However, when complying with the Electrical Appliance and Material Safety
Law, this becomes 75°C.
Temperature Rise Due to Pulse Voltage
When a pulse voltage with ON time of less than 2 minutes is used, the coil temperature rise bares no relationship to the ON
time. This varies with the ratio of ON time to OFF time, and compared with continuous current passage, it is rather small.
The various relays are essentially the same in this respect.
Current passage time %

For continuous passage Temperature rise value is 100%

ON:OFF = 3:1 About 80%
ON:OFF = 1:1 About 50%
ON:OFF = 1:3 About 35%

Operate Voltage Change Due to Coil Temperature Rise (Hot Start)

In DC relays, after continuous passage of current in the coil, if the current is turned OFF, then immediately turned ON again, due
to the temperature rise in the coil, the operate voltage will become somewhat higher. Also, it will be the same as using it in a
higher temperature atmosphere.
The resistance/temperature relationship for copper wire is about 0.4% for 1°C, and with this ratio the coil resistance increases.
That is, in order to operate of the relay, it is necessary that the voltage be higher than the operate voltage and the operate
voltage rises in accordance with the increase in the resistance value. However, for some polarized relays, this rate of change is
considerably smaller.

4. Coil Applied Voltage and Operate Time

In the case of AC operation, there is extensive variation in operate time depending upon the point in the phase at which the
switch is turned ON for coil excitation, and it is expressed as a certain range, but for miniature types it is for the most part 1/2
cycle. However, for the somewhat large type relay where bounce is large, the operate time is 7 to 16ms, with release time in the
order of 9 to 18ms Also, in the case of DC operation, to the extent of large coil input, the operating time is rapid, but if it is too
rapid, the "Form A" contact bounce time is extended. Please be warned that load conditions (in particular when inrush current is
large or load is close to the load rating) may cause the working life to shorten and slight welding.

5. Stray Circuits (Bypass Circuits)

In the case of sequence circuit construction, because of bypass flow or alternate routing, it is necessary to take care not to have
erroneous operation or abnormal operation. To understand this condition while preparing sequence circuits, as shown in Fig. 4,
with 2 lines written as the power source lines, the upper line is always (+) and the lower line (-) (when the circuit is AC, the same
thinking applies). Accordingly the (+) side is necessarily the side for making contact connections (contacts for relays, timers, limit
switches, etc.), and the (-) side is the load circuit side (relay coil, timer coil, magnet coil, solenoid coil, motor, lamp, etc.).
Fig. 5 shows an example of stray circuits. In Fig. 5(a), with contacts A, B, and C closed, after relays R1, R2, and R3operate, if
contacts B and C open, there is a series circuit through A, R1, R2, and R3, and the relays will hum and sometimes not be
restored to the drop out condition.
The connections shown in Fig. 5(b) are correctly made. In addition, with regard to the DC circuit, because it is simple by means
of a diode to prevent stray circuits, proper application should be made.
 6. Gradual Increase of Coil Impressed Voltage and Suicide Circuit
When the voltage impressed on the coil is increased slowly, the relay transferring operation is unstable, the contact pressure
drops, contact bounce increases, and an unstable condition of contact occurs. This method of applying voltage to the coil should
not be used, and consideration should be given to the method of impressing voltage on the coil (use of switching circuit). Also, in
the case of latching relays, using self "Form B" contacts, the method of self coil circuit for complete interruption is used, but
because of the possibility of trouble developing, care should be taken.
The circuit shown in Fig. 6 causes a timing and sequential operation using a reed type relay, but this is not a good example with
mixture of gradual increase of impressed voltage for the coil and a suicide circuit. In the timing portion for relay R1, when the
timing times out, chattering occurs causing trouble. In the initial test (trial production), it shows favorable operation, but as the
number of operations increases, contact blackening (carbonization) plus the chattering of the relay creates instability in
performance.

7. Phase Synchronization in AC Load Switching

If switching of the relay contacts is synchronized with the phase of the AC power, reduced electrical life, welded contacts, or a
locking phenomenon (incomplete release) due to contact material transfer may occur. Therefore, check the relay while it is
operating in the actual system. When driving relays with timers, micro computers and thyristors, etc., there may be
synchronization with the power supply phase.

8. Erroneous Operation Due to Inductive Interference

For long wire runs, when the line for the control circuit and the line for electric power use a single conduit, induction voltage,
caused by induction from the power line, will be applied to the operation coil regardless of whether or not the control signal is off.
In this case the relay and timer may not revert. Therefore, when wiring spans a long distance please remember that along with
inductive interference, connection failure may be caused by a problem with distribution capacity or the device might break down
due to the influenced of externally caused surges, such as that caused by lightning.

9. Long Term Current Carrying

A circuit that will be carrying a current continuously for long periods without relay switching operation. (circuits for emergency
lamps, alarm devices and error inspection that, for example, revert only during malfunction and output warnings with form B
contacts)
Continuous, long-term current to the coil will facilitate deterioration of coil insulation and characteristics due to heating of the coil
itself. For circuits such as these, please use a magnetic-hold type latching relay. If you need to use a single stable relay, use a
sealed type relay that is not easily affected by ambient conditions and make a failsafe circuit design that considers the possibility
of contact failure or disconnection.

10. Usage With Infrequent Switching

Please carry out periodic contact conductivity inspections when the frequency of switching is once or fewer times per month.
When no switching of the contacts occurs for long periods, organic membrane may form on the contact surfaces and lead to
contact instability.

11. Regarding Electrolytic Corrosion of Coils

In the case of comparatively high voltage coil circuits, when such relays are used in high temperature and high humidity
atmospheres or with continuous passage of current, the corrosion can be said to be the result of the occurrence of electrolytic
corrosion. Because of the possibility of open circuits occurring, attention should be given to the following points.
1. The (+) side of the power source should be connected to the chassis. (Refer to Fig. 8) (Common to all relays)
2. In the case where unavoidably the (-) side is grounded, or in the case where grounding is not possible.
(1) Insert the contacts (or switch) in the (+) side of the power source. (Refer to Fig. 9) (Common to all relays)
(2) When a grounding is not required, connect the ground terminal to the (+) side of the coil. (Refer to Fig. 10) (NF and
NR with ground terminal)
3. When the (-) side of the power source is grounded, always avoid interting the contacts (and switches) in the (-) side.
(Refer to Fig. 11) (Common to all relays)
4. In the case of relays provided with a ground terminal, when the ground terminal is not considered effective, not making a
connection to ground plays an important role as a method for preventing electrolytic corrosion.
Note: The designation on the drawing indicates the insertion of insulation between the iron core and the chassis. In relays where
a ground terminal is provided, the iron core can be grounded directly to the chassis, but in consideration of electrolytic corrosion,
it is more expedient not to make the connection.
 Return to top

3. Precautions Regarding Contact

CONTACT
The contacts are the most important elements of relay construction. Contact performance conspicuously influenced by contact
material, and voltage and current values applied to the contacts (in particular, the voltage and current waveforms at the time of
application and release), the type of load, frequency of switching, ambient atmosphere, form of contact, contact switching
speed, and of bounce.
Because of contact transfer, welding, abnormal wear, increase in contact resistance, and the various other damages which bring
about unsuitable operation, the following items require full investigation.
* We recommend that you verify with one of our sales offices.
1. Basic Precautions Regarding Contact
Voltage
When there is inductance included in the circuit, a rather high counter emf is generated as a contact circuit voltage, and since, to
the extent of the value of that voltage, the energy applied to the contacts causes damage with consequent wear of the contacts,
and transfer of the contacts, it is necessary to exercise care with regard to control capacity. In the case of DC, there is no zero
current point such as there is with AC, and accordingly, once a cathode arc has been generated, because it is difficult to quench
that arc, the extended time of the arc is a major cause. In addition, due to the direction of the current being fixed, the
phenomenon of contact shift, as noted separately below, occurs in relation to the contact wear. Ordinarily, the approximate
control capacity is mentioned in catalogs or similar data sheets, but this alone is not sufficient. With special contact circuits, for
the individual case, the maker either estimates from the past experience or makes test on each occasion. Also, in catalogs and
similar data sheets, the control capacity that is mentioned is limited to resistive load, but there is a broad meaning indicated for
that class of relay, and ordinarily it is proper to think of current capacity as that for 125V AC circuits.
Minimum applicable loads are given in the catalog; however, these are only provided as a guide to the lower limit that the relay
is able to switch and are not guaranteed values.
The level of reliability of these values depends on switching frequency, ambient conditions, change in the desired contact
resistance, and the absolute value.
Please use relays with AgPd contacts when minute analog load control or contact resistance no higher than 100 mΩ is desired
(for measurement and wireless applications, etc.).
Current
The current at both the closing and opening time of the contact circuit exerts important influence. For example, when the load is
either a motor or a lamp, to the extent of the inrush current at the time of closing the circuit, wear of the contacts, and the
amount of contact transfer increase, and contact welding and contact transfer make contact separation impossible.

2. Characteristics of Common Contact Materials

Characteristics of contact materials are given below. Refer to them when selecting a relay.
Electrical conductivity and thermal conductivity are the highest of all metals. Exhibits low
Ag
contact resistance, is inexpensive and widely used. A disadvantage is it easily develops a
(silver)
sulfide film in a sulfide atmosphere. Care is required at low voltage and low current levels.
AgSnO2 Exhibits superior welding resistance; however, as with Ag, it easily develops a sulfide film in a
(silver-tin) sulfide atmosphere.

Hardness and melting point are high, arc resistance is excellent, and it is highly resistant to
Contact AgW material transfer. However, high contact pressure is required. Furthermore, contact resistance
Material (silver-tungsten) is relatively high and resistance to corrosion is poor. Also, there are constraints on processing
and mounting to contact springs.
AgNi
Equals the electrical conductivity of silver. Excellent arc resistance.
(silver-nickel)
AgPd Exhibits high resistance to corrosion and sulfidation at room temperature; however, in low-level
(silver- circuits, it easily absorbs organic gases and forms polymers. Gold cladding or other measures
palladium) should be used to prevent such polymer buildup.
Combines perfect corrosion resistance and hardness. As plated contacts, used for relatively
Rh plating
light loads. In an organic gas atmosphere, care is required as polymers may develop.
(rhodium)
Therefore, it is used in hermetic seal relays (reed relays, etc.) .
Au with its excellent corrosion resistance is pressure welded onto a base metal. Special
Au clad characteristics are uniform thickness and the nonexistence of pinholes. Greatly effective
(gold clad) especially for low level loads under relatively adverse atmospheres. Often difficult to implement
Surface clad contacts in existing relays due to design and installation.
Finish Similar effect to Au cladding. Depending on the plating process used, supervision is important
Au plating
as there is the possibility of pinholes and cracks. Relatively easy to implement gold plating in
(gold plating)
existing relays.
Au flash plating
Purpose is to protect the contact base metal during storage of the switch or device with built-in
(gold thin-film
switch. However, a certain degree of contact stability can be obtained even when switching
plating)
loads.
0.1 to 0.5 μm

3. Contact Protection
Counter EMF
When switching inductive loads with a DC relay such as relay sequence circuits, DC motors, DC clutches, and DC solenoids, it
is always important to absorb surges (e.g. with a diode) to protect the contacts.
When these inductive loads are switched off, a counter emf of several hundred to several thousand volts develops which can
severely damage contacts and greatly shorten life. If the current in these loads is relatively small at around 1A or less, the
counter emf will cause the ignition of a glow or arc discharge. The discharge decomposes organic matter contained in the air
and causes black deposits (oxides, carbides) to develop on the contacts. This may result in contact failure.
Example of counter emf and actual measurement
In Fig. 12 (a), a counter emf (e = -L di/dt) with a steep waveform is generated across the coil with the polarity shown in Fig. 12
(b) at the instant the inductive load is switched off. The counter emf passes through the power supply line and reaches both
contacts.
Generally, the critical dielectric breakdown voltage at standard temperature and pressure in air is about 200 to 300 volts.
Therefore, if the counter emf exceeds this, discharge occurs at the contacts to dissipate the energy (1/2Li2)
stored in the coil. For this reason, it is desirable to absorb the counter emf so that it is 200V or less.
Material Transfer Phenomenon
Material transfer of contacts occurs when one contact melts or boils and the contact material transfers to the other contact. As
the number of switching operations increases, uneven contact surfaces develop such as those shown in Fig. 13. After a while,
the uneven contacts lock as if they were welded together. This often occurs in circuits where sparks are produced at the moment
the contacts "make" such as when the DC current is large for DC inductive or capacitive loads or when the inrush current is
large (several amperes or several tens of amperes).
Contact protection circuits and contact materials resistant to material transfer such as AgSnO2, AgW or AgCu are used as
countermeasures. Generally, a concave formation appears on the cathode and a convex formation appears on the anode. For
DC capacitive loads (several amperes to several tens of amperes), it is always necessary to conduct actual confirmation tests.

Contact Protection Circuit

Use of contact protective devices or protection circuits can suppress the counter emf to a low level. However, note that incorrect
use will result in an adverse effect. Typical contact protection circuits are given in the table below.
(G: Good, NG: No Good, C: Care)

Application
Circuit Features/Others Devices Selection
AC DC

If the load is a timer, leakage

current flows through the CR
circuit causing faulty
operation. * If used with AC
voltage, be sure the
As a guide in selecting c and r,
impedance of the load is c: 0.5 to 1μF per 1A contact
sufficiently smaller than that current
of the CR circuit
C* G r: 0.5 to 1Ω per 1V contact voltage
If the load is a relay or Values vary depending on the
solenoid, the release time properties of the load and
lengthens. Effective when variations in relay characteristics.
CR connected to both contacts if Capacitor “c” acts to suppress the
circuit the power supply voltage is discharge the moment the contacts
24 or 48V and the voltage open. Resistor “r” acts to limit the
across the load is 100 to current when the power is turned
200V. on the next time. Test to confirm.
If the load is a relay or Use a capacitor “c” with a
solenoid, the release time breakdown voltage of 200 to 300V.
lengthens. Effective when Use AC type capacitors
connected to both contacts if (nonpolarized) for AC circuits.
G G
the power supply voltage is
24 or 48V and the voltage
across the load is 100 to
200V.
The diode connected in
parallel causes the energy Use a diode with a reverse
stored in the coil to flow to breakdown voltage at least 10
the coil in the form of current times the circuit voltage and a
and dissipates it as joule forward current at least as large as
Diode heat at the resistance the load current. In electronic
NG G
circuit component of the inductive circuits where the circuit voltages
load. This circuit further are not so high, a diode can be
delays the release time used with a reverse breakdown
compared to the CR circuit. voltage of about 2 to 3 times the
(2 to 5 times the release time power supply voltage.
listed in the catalog)

Diode
and Effective when the release Use a zener diode with a zener
zener NG G time in the diode circuit is too voltage about the same as the
diode long. power supply voltage.
circuit

Using the stable voltage

characteristics of the varistor,
this circuit prevents
excessively high voltages
from being applied across
the contacts. This circuit also
Varistor
G G slightly delays the release —
circuit
time. Effective when
connected to both contacts if
the power supply voltage is
24 or 48V and the voltage
across the load is 100 to
200V.

Avoid using the protection circuits shown in the figures on the right. Although DC inductive loads are usually more difficult to
switch than resistive loads, use of the proper protection circuit will raise the characteristics to that for resistive loads.
Although extremely effective in arc suppression as the contacts open, the contacts are susceptible to welding since energy is
stored in C when the contacts open and discharge current flows from C when the contacts close.

Although extremely effective in arc suppression as the contacts open, the contacts are susceptible to welding since charging
current flows to C when the contacts close.
Mounting the Protective Device
In the actual circuit, it is necessary to locate the protective device (diode, resistor, capacitor, varistor, etc.) in the immediate
vicinity of the load or contact. If located too far away, the effectiveness of the protective device may diminish. As a guide, the
distance should be within 50cm.
Abnormal Corrosion During High Frequency Switching of DC Loads (spark generation)
If, for example, a DC valve or clutch is switched at a high frequency, blue-green rust may develop. This occurs from the reaction
of nitrogen and oxygen in the air when sparks (arc discharge) are generated during switching. Therefore, care is required in
circuits where sparks are generated at a high frequency.

4. Cautions on Use Related to Contacts

Connection of Load and Contacts
Connect the load to one side of the power supply as shown in Fig. 14 (a). Connect the contacts to the other side. This prevents
high voltages from developing between contacts. If contacts are connected to both side of the power supply as shown in Fig. 14
(b), there is a risk of shorting the power supply when relatively close contacts short.

Dummy Resistor
Since voltage levels at the contacts used in low current circuits (dry circuits) are low, poor conduction is often the result. One
method to increase reliability is to add a dummy resistor in parallel with the load to intentionally raise the load current reaching
the contacts.
Avoid Circuits Where Shorts Occur Between Form A and B Contacts
1. The clearance between form A and B contacts in compact control components is small. The occurrence of shorts due to
arcing must be assumed.
2. Even if the three N.C., N.O., and COM contacts are connected so that they short, a circuit must never be designed to allow
the possibility of burning or generating an overcurrent.
3. A forward and reverse motor rotation circuit using switching of form A and B contacts must never be designed.
Bad example of Form A and B use

Shorts Between Different Electrodes

Although there is a tendency to select miniature control components because of the trend toward miniaturizing electrical control
units, care must be taken when selecting the type of relay in circuits where different voltages are applied between electrodes in
a multi-pole relay, especially when switching two different power supply circuits. This is not a problem that can be determined
from sequence circuit diagrams. The construction of the control component itself must be examined and sufficient margin of
safety must be provided especially in creepage between electrodes, space distance, presence of barrier, etc.
Type of Load and Inrush Current
The type of load and its inrush current characteristics, together with the switching frequency, are important factors which cause
contact welding. Particularly for loads with inrush currents, measure the steady state and inrush current.
Then select a relay which provides an ample margin of safety. The table on the right shows the relationship between typical
loads and their inrush currents.
Also, verify the actual polarity used since, depending on the relay, electrical life is affected by the polarity of COM and NO.

Type of load Inrush current

Resistive load Steady state current

Solenoid load 10 to 20 times the steady state current
Motor load 5 to 10 times the steady state current
Incandescent lamp load 10 to 15 times the steady state current
Mercury lamp load Approx. 3 times the steady state current
Sodium vapor lamp load 1 to 3 times the steady state current
Capacitive load 20 to 40 times the steady state current
Transformer load 5 to 15 times the steady state current

Load Inrush Current Wave and Time

(1)Incandescent Lamp Load
 Inrush current/rated current:i/io≒10 to 15 times

(2)Mercury Lamp Load i/io≒3 times

The discharge tube, transformer, choke coil, capacitor, etc., are combined in common discharge lamp circuits. Note that the
inrush current may be 20 to 40 times, especially if the power supply impedance is low in the high power factor type.

(3)Fluorescent Lamp Load i/io≒5 to 10 times

(4)Motor Load i/io≒5 to 10 times

Conditions become more harsh if plugging or inching is performed since state transitions are repeated.
When using a relay to control a DC motor and brake, the on time surge current, normal current and off time brake current
differ depending on whether the load to the motor is free or locked. In particular, with non-polarized relays, when using from b
contact of from contact for the DC motor brake, mechanical life might be affected by the brake current. Therefore, please
verify current at the actual load.

(5)Solenoid Load i/io≒10 to 20 times

Note that since inductance is great, the arc lasts longer when power is cut. The contact may become easily worn.

(6)Electromagnetic Contact Load i/io≒3 to 10 times (7)Capacitive Load i/io≒20 to 40 times

When Using Long Wires

If long wires (100 to 300m) are to be used in a relay contact circuit, inrush current may become a problem due to the stray
capacitance existing between wires. Add a resistor (approx. 10 to 50Ω) in series with the contacts.
Electrical Life at High Temperatures
Verify at the actual use condition since electrical life may be affected by use at high temperatures.

Return to top

4. Precautions Regarding Latching Relays

Latching relays are shipped from the factory in the reset state. A shock to the relay during shipping or installation may cause it
to change to the set state. Therefore, it is recommended that the relay be used in a circuit which initializes the relay to the
required state (set or reset) whenever the power is turned on.
Avoid impressing voltages to the set coil and reset coil at the same time.
Connect a diode as shown since latching may be compromised when the relay is used in the following circuits.
If set coils or reset coils are to be connected together in parallel, connect a diode in series to each coil. Fig. 16(a), (b)

Also, if the set coil of a relay and the reset coil of another relay are connected in parallel, connect a diode to the coils in series.
Fig. 16 (c)

If the set coil or reset coil is to be connected in parallel with an inductive load (e.g. another electromagnetic relay coil, motor,
transformer, etc.), connect a diode to the set coil or reset coil in series. Fig. 16 (d)

Use a diode having an ample margin of safety for repeated DC reverse voltage and peak reverse voltage applications and
having an average rectified current greater than or equal to the coil current.
Avoid applications in which conditions include frequent surges to the power supply.
Avoid using the following circuit since self-excitation at the contacts will inhibit the normal keep state.

Four-Terminal Latching Relay

In the 2-coil latching type circuit as shown below, one terminal at one end of the set coil and one terminal at one end of the reset
coil are connected in common and voltages of the same polarity are applied to the other side for the set and reset operations. In
this type of circuit, short 2 terminals of the relay as noted in the next table. This helps to keep the insulation high between the
two winding.

Minimum Pulse Width

As a guide, make the minimum pulse width in order to set or reset a latching relay at least 5 times the set time or reset time of
each product and apply a rectangular-wave rated voltage. Also, please verify operation. Please inquire if you cannot obtain a
pulse width of at least 5 times the set (reset) time. Also, please inquire regarding capacitor drive.
 Relay Type Terminal Nos.
1c -
DS
2c 15&16
ST *
SP 2&4

* * ST relays are constructed so that the set coil and reset coil are separated for high insulation resistance.
* DSP, TQ, S relays are not applicable due to polarity.

Two Coil Latch Induction Voltage

Each coil in a 2-coil latch relay is wound with a set coil and a reset coil on the same iron cores.
Accordingly, induction voltage is generated on the reverse side coil when voltage is applied and shut off to each coil.
Although the amount of induction voltage is about the same as the rated relay voltage, you must be careful of the reverse bias
voltage when driving transistors.

Return to top

5. Handling Cautions for Tube Packaging

Some types of relays are supplied in tube packaging. If you remove any relays from the tube packaging, be sure to slide the
stop plug at one end to hold the remaining relays firmly together so they would not move in the tube. Failing to do this may lead
to the appearance and/or performance being damaged.

Return to top

6. Ambient Environment

1. Ambient Temperature and Atmosphere

Be sure the ambient temperature at the installation does not exceed the value listed in the catalog. Furthermore,
environmentally sealed type (plastic sealed type) should be considered for applications in an atmosphere with dust, sulfur gases
(SO2 , H2 S), or organic gases.

2. Silicone
When a source of silicone substances (silicone rubber, silicone oil, silicone coating materials and silicone filling materials etc.) is
used around the relay, the silicone gas (low molecular siloxane etc.) may be produced. This silicone gas may penetrate into the
inside of the relay.
When the relay is kept and used in this condition, silicone compound may adhere to the relay contacts which may cause the
contact failure.
Do not use any sources of silicone gas around the relay (Including plastic seal types).

3. NOx Generation
When relay is used in an atmosphere high in humidity to switch a load which easily produces an arc, the NOx created by the arc
and the water absorbed from outside the relay combine to produce nitric acid. This corrodes the internal metal parts and
adversely affects operation.
Avoid use at an ambient humidity of 85% RH or higher (at 20°C).
If use at high humidity is unavoidable, please contact our sales representative.

4. Vibration and Shock

If a relay and magnetic switch are mounted next to each other on a single plate, the relay contacts may separate momentarily
from the shock produced when the magnetic switch is operated and result in faulty operation. Countermeasures include
mounting them on separate plates, using a rubber sheet to absorb the shock, and changing the direction of the shock to a
perpendicular angle. Also, if the relay will be subject to continual vibration (trains, etc.), do not use it with a socket. We
recommend that you solder directly to the relay terminals.

5. Influence of External Magnetic Fields

When a magnet or permanent magnet in any other large relay, transformer, or speaker is located nearby, the relay
characteristics may change and faulty operations may result. The influence depends on the strength of the magnetic field and it
should be checked at the installation.

6. Usage, Storage, and Transport Conditions

During usage, storage, or transportation, avoid locations subject to direct sunlight and maintain normal temperature, humidity,
and pressure conditions.
The allowable specifications for environments suitable for usage, storage, and transportation are given below.
1. Temperature: The allowable temperature range differs for each relay, so refer to the relay’s individual specifications. In
addition, when transporting or storing relays while they are tube packaged, there are cases when the temperature may
differ from the allowable range. In this situation, be sure to consult the individual specifications.
2. Humidity: 5 to 85% RH
The humidity range varies with the temperature.
Use within the range indicated in the graph.
(The allowable temperature depends on the relays.)

3. Pressure: 86 to 106 kPa

Condensation
Condensation occurs when the ambient temperature drops suddenly from a high temperature and humidity, or the relay and
microwave device is suddenly transferred from a low ambient temperature to a high temperature and humidity. Condensation
causes the failures like insulation deterioration, wire disconnection and rust etc.
Panasonic Corporation does not guarantee the failures caused by condensation.
The heat conduction by the equipment may accelerate the cooling of device itself, and the condensation may occur. Please
conduct product evaluations in the worst condition of the actual usage. (Special attention should be paid when high temperature
heating parts are close to the device. Also please consider the condensation may occur inside of the device.)
Icing
Condensation or other moisture may freeze on relays when the temperature become lower than 0°C.
This icing causes the sticking of movable portion, the operation delay and the contact conduction failure etc.
Panasonic Corporation does not guarantee the failures caused by the icing.
The heat conduction by the equipment may accelerate the cooling of relay itself and the icing may occur.
Please conduct product evaluations in the worst condition of the actual usage.
Low temperature and low humidity
The plastic becomes brittle if the switch is exposed to a low temperature, low humidity environment for long periods of time.
High temperature and high humidity
Storage for extended periods of time (including transportation periods) at high temperature or high humidity levels or in
atmospheres with organic gases or sulfide gases may cause a sulfide film or oxide film to form on the surfaces of the contacts
and/or it may interfere with the functions.
Check out the atmosphere in which the units are to be stored and transported.
Package
In terms of the packing format used, make every effort to keep the effects of moisture, organic gases and sulfide gases to the
absolute minimum.
Storage requirements
Since the surface-mount terminal type is sensitive to humidity it is packaged with tightly sealed anti-humidity packaging.
However, when storing, please be careful of the following.
1. Please use promptly once the anti-humidity pack is opened.
(within 72 hours, Max. 30°C / 70% RH).
If left with the pack open, the relay will absorb moisture which will cause thermal stress when reflow mounting and thus
cause the case to expand. As a result, the seal may break.
2. If relays will not be used within 72 hours, please store relays in a humidity controlled desiccator or in an anti-humidity bag
to which silica gel has been added.
* If the relay is to be soldered after it has been exposed to excessive humidity atmosphere, cracks and leaks can occur.
Be sure to mount the relay under the required mounting conditions.
3. The following cautionary label is affixed to the anti-humidity pack.

7. Vibration, Impact and Pressure when Shipping

When shipping, if strong vibration, impact or heavy weight is applied to a device in which a relay is installed, functional damage
may occur. Therefore, please package in a way, using shock absorbing material, etc., so that the allowable range for vibration
and impact is not exceeded.

Return to top

7. Environmentally Sealed Type Relays

Sealed type relays are available. They are effective when problems arise during PC board mounting (e.g. automatic soldering
and cleaning). They also, of course, feature excellent corrosion resistance. Note the cautions below regarding the features and
use of environmentally sealed type relays to avoid problems when using them in applications.
1. Operating Environment
Plastic sealed type relays are not suited for use in environments that especially require air tightness. Although there is no
problem if they are used at sea level, avoid atmospheric pressures beyond 96±10kPa. Also avoid using them in an atmosphere
containing flammable or explosive gases.

2. Cleaning
When cleaning a printed circuit board after soldering, we recommend using alcohol based cleaning fluids. Please avoid
ultrasonic cleaning. The ultrasonic energy from this type of cleaning may cause coil line breakage and light sticking of contacts.

Return to top

8. Mounting Considerations

1. Top View and Bottom View

Relays used for PC boards, especially the flat type relays, have their top or bottom surface indicated in the terminal wiring
diagrams.

Relay with terminals viewed from the bottom (terminals cannot be seen from the top)

Relay with terminals viewed from the top (all terminals can be seen from the top)
Note during PC board pattern design (NC relay)

2. Mounting Direction
Mounting direction is important for optimum relay characteristics.
Shock Resistance
It is ideal to mount the relay so that the movement of the contacts and movable parts is perpendicular to the direction of
vibration or shock. Especially note that the vibration and shock resistance of Form B contacts while the coil is not excited is
greatly affected by the mounting direction of the relay.
Contact Reliability
Mounting the relay so the surfaces of its contacts (fixed contacts or movable contacts) are vertical prevents dirt and dust as well
as scattered contact material (produced due to large loads from which arcs are generated) and powdered metal from adhering
to them.
Furthermore, it is not desirable to switch both a large load and a low level load with a single relay. The scattered contact material
produced when switching the large load adheres to the contacts when switching the low level load and may cause contact
failure. Therefore, avoid mounting the relay with its low level load contacts located below the large load contacts.
The installation direction is specified for some models. Please check with the product catalog and make sure to use the correct
installation direction.

3. Adjacent Mounting
When many relays are mounted close together, abnormally high temperatures may result from the combined heat generated.
Mount relays with sufficient spacing between them to prevent heat buildup.
This also applies when a large number of boards mounted with relays are installed as in a card rack. Be sure the ambient
temperature of the relay does not exceed the value listed in the catalog.
Influence of Adjacent Mounting of Polarized Relays
When polarized relays are mounted close together, their characteristics change. Since the affect of adjacent mounting differs
according to the type of relay, refer to the data for the particular type.

4. Panel Mounting
Do not remove the cover. It has a special function. (It will not come off under normal handling.)
When installing please use washers to prevent damage and deformation. Please keep the tightening torque to within 0.49 to
0.686 N·m (5 to 7 kgf·cm). Also, please use a spring washer to prevent it from coming loose.

5. Tab Terminals
As a guide, use a quick connect mounting pressure of 40 to 70N {4 to 7 kgf} for relays with tab terminals.

Return to top

9. Method of Mounting and Lead Wires Connection

1. Method of Mounting
The direction of mounting is not specifically designated, but to the extent possible, the direction of contact movement should be
such that vibration and shock will not be applied.
When a terminal socket is used
When a Terminal Socket is Used
After drilling the mounting holes, the terminal socket should be mounted making certain the mounting screws are not loose.
DIN standard sockets are available for one-touch mounting on DIN rail of 35mm/ 1.378 inch width.

When Reversible Terminal Sockets are Used

The reversible terminal sockets (HC, HL socket) are for one-touch mounting. (A panel thickness of 1 to 2mm/ .039 to .079 inch
should be used.)

The socket should be pushed through the opening in the mounting panel until the projections on the side of the mounting
bracket extend out over the back surface.

When all four of the projections are visible from the back side of the mounting panel, the mounting is completed and the
socket is fastened.
To remove the socket, the projections on the side of the mounting bracket should be pushed inward and at the same time the
body of the socket should be pushed lightly from the back side. The socket can then be removed from the panel.

2. Connection of Lead Wires

When making the connections, depending upon the size of load, the wire cross-section should be at least as large as the
values shown in the table below.
(Table 1)
Permissible current (A) Cross-section (mm2)
2 0.2
3 0.3
5 0.5
7.5 0.75
12.5 1.25
15 2
20 2
30 3.5

When the terminal socket uses screw fastening connections, either pressure terminals or other means should be used to
make secure fastening of the wire.
To prevent damage and deformity, please use a torque within the following range when tightening the push screw block of the
terminal socket.
M4.5 screw : 1.47 to 1.666 N•m (15 to 17 kgf•cm)
M4 screw : 1.176 to 1.37 N•m (12 to 14 kgf•cm)
M3.5 screw : 0.784 to 0.98 N•m (8 to 10 kgf•cm)
M3 screw : 0.49 to 0.69 N•m (5 to 7 kgf•cm)
 Return to top

10. Cautions for Use-Check List

Coil Drive Input

1. Is the correct rated voltage applied?
2. Is the applied coil voltage within the allowable continuous voltage limit?
3. Is the ripple in the coil voltage within the allowable level?
4. For voltage applied to a polarized coil, is polarity observed?
5. When hot start is required, is the increase in coil resistance resulting from coil temperature rise taken into account in setting
coil voltage?
6. Is the coil voltage free from momentary drop caused by load current? (Pay special attention for self-holding relays.)
7. Is supply voltage fluctuation taken into account when setting the rated coil voltage?
8. The relay status may become unstable if the coil voltage (current) is gradually increased or decreased.
Was the relay tested in a real circuit or with a real load?
9. When driving with transistors, did you consider voltage drops?

Load(Relay Contacts)
1. Is the load rated within the contact ratings?
2. Does the load exceed the contacts' minimum switching capacity?
3. Special attention is required for contact welding when the load is a lamp, motor, solenoid, or electromagnetic contractor. Was
the relay tested with a real load?
4. A DC load may cause contact lock-up due to large contact transfer. Was the relay tested with a real load?
5. For an inductive load, is a surge absorber used across the contacts?
6. When an inductive load causes heavy arc discharge across the relay contacts, the contacts may be corroded by chemical
reaction with nitrogen in the atmosphere. Was the relay tested with a real load?
7. Platinum contacts may generate brown powder due to a catalyzer effect or vibration energy. Was the relay tested with a real
load?
8. Is the contact switching frequency below the specification?
9. When there are more than two sets of contacts (2T) in a relay, metallic powder shed from one set of contacts may cause a
contact failure on the other set (particularly for light loads). Was the relay tested in a real load?
10. A delay capacitor used across relay contacts may cause contact welding. Was the relay tested with a real load?
11. For an AC relay, a large contact bounce may cause contact welding. Was the relay tested in a real circuit or with a real load?
12. A high voltage may be induced at transformer load. Was the relay tested with a real load?

Circuit Design
1. Does circuit design take into account electrolytic corrosion of the coil?
2. Are transistors and other circuit components protected rom counter electromotive force that develops across the relay coil?
3. Is the circuit designed so the relay coil is left deenergized while the relay is inactive for long period of time?
4. Is the relay operated within the ratings approved by the relevant international standard (if compliance is required)?
5. Is the circuit protected from malfunction when the relay's activation and/or deactivation time varies considerably?
6. Is the circuit protected from malfunctions that might result from relay contact bounce?
7. Is the circuit protected from malfunction when a high-sensitivity self-holding relay, such as NR type, is to be used?
8. When there are two or more sets of contacts (2T) in a relay, arc discharges from load switching may cause short circuits
across the two or more sets of contacts. Is the circuit designed to suppress such arc discharges?
9. Item 8 above also requires special attention when loads are supplied from separate power sources.
10. Does the post-installation insulation distance comply with the requirement of the relevant international standard or the
Electrical Appliance and Material Control Law?
11. Is the circuit protected from malfunction when the relay is to be driven by transistors?
12. When the SCR is used for on/off control, the relay activation tends to synchronize with the line frequency, resulting in an
extremely shortened life. Was the relay tested in a real circuit or with a real load?
13. Does the PC board design take into account use of on-board relay?
14. RF signals may leak across relay's open contacts. Check for adequate contact isolation and use RF relays as needed.

Operating Environment
1. Is the ambient temperature in the allowable operating temperature range?
2. Is the humidity in the allowable humidity range?
3. Is the operating atmosphere free from organic and sulfide gases?
4. Is the operating atmosphere free from silicon gas? Depending on the load type, silicon gas may cause a black substance to
from on the contacts, leading to contact failure.
5. Is the operating atmosphere free from excessive airborne dust?
6. Is the relay protected from oil and water splashes?
7. Is the relay protected from vibration and impact which may cause poor contact with the socket?
8. Is ambient vibration and impact below the level allowable for the relay?
9. Is the relay free from mechanical resonance after it is installed in position?
10. Is insulation coating applied to the relay along with the PC board? Depending on the load type, a black substance may form to
cause contact failure.

Installation and Connection

1. Is the relay protected from solder chips and flux when it is manually soldered?
2. Are preparations for flux application and automatic soldering complete?
3. Is the PC board cleaning process designed to minimize adverse affects to the relays?
4. Are adequate separations provided between polarized or reed relays to prevent magnetic coupling?
5. Are the relay terminals free from stress in the socket?
6. Polarized relay's characteristics may be affected by strong external magnetic field. Are the relays installed away from such
fields?
7. If very long leads (several 10m more) are used to connect the load, the stray capacity existing across the leads may cause the
inrush current. Was the relay tested with a real load?
8. Unless otherwise specified, all relay terminals should be soldered at 250°C/ 482°F within 5 sec. or at 350°C/ 662°F within 3
sec.
9. A badly warped PC board can cause stress to the relay terminals which may lead to degraded relay characteristics.
10. Glass shot should not be used to clean the PC board of solder flux. This may cause relay malfunction due to glass powder
becoming lodged in the relay's internal structure.
11. Relays should always be used with their plastic shields installed, or degraded relay performance may result.
12. Do not cut away any relay terminal as the stress may cause degraded relay performance.

Storage and Transport

1. Is the relay subject to freezing or condensation (especially when shipping)?
2. Is the temperature in the allowable temperature range?
3. Is the humidity in the allowable humidity range?
4. Is the storing atmosphere free from organic and sulfide gases?
5. Is the storing atmosphere free from excessive airborne dust?
6. Is the relay protected from oil and water splashes?
7. Is the relay subject to the application of heavy weight?
8. When shipping does vibration and impact exceed the allowable range?

Return to top

Related Information
 Configuration and Construction Relay Soldering and Cleaning Guidelines
Reliability Cautions for Surface Mount Relay Installation
Relay Terminology Relays Lineup
Applications of Relays in Electronic Circuits

Catalog Download

Title Language File size Update

リレー使用上の注意事項
各種リレー共通(パワー,安全,シグナル,高周波,制御盤,高容量,インターフェイスターミ JP 1.8MB January 31, 2019
ナル)

General Application Guidelines

Power Relays(Over 2A),Safty Relays,Signal Relays(2A or less),Microwave
Devices,Control Panel Relays,High-capacity DC Cutoff Relays and Interface
EN 367.3KB July 31, 2014
Terminal.

继电器使用上的注意事项 CN-Simplified 820.6KB August 9, 2019

Return to top

Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Business > Industrial Devices > Automation Controls Top > Components & Devices > Relays / Couplers > Relays Cautions for Use

Consumer Digital Cameras Digital Video Cameras Technics SD Cards Batteries Air Conditioning Telephones Home Network System
Faxes (Drivers/Software) Network Cameras Mobile Phones (Software) Video Intercom Tourist Models

Business Communication Solutions Security Systems Personal Computer Professional AV Document & Imaging Solutions
Optical Disc Archive Solution Recording Media Video Intercom Air Conditioning Ventilation, Air Purification, etc. Photovoltaic
Lighting Wiring Devices Factory Flexible wiring System Housing Equipment Devices Power Supply Solutions
Industrial Devices & Solutions Semiconductor Automation Controls Targeting ITS by Panasonic Healthcare

Support

About Us Sustainability IR News Major Exhibitions Words of Wisdom

Print Page top Area / Country

Copyright © Panasonic Corporation

Site Map Terms of Use Privacy Policy Cookies Policy Handling of personal information