MD0701KE140203

Analog timer Suffix code

T38N/T48N
Model Code Description
INSTRUCTION ☐- ☐ ☐ ☐
☐ Analog timer
MANUAL 40.5(W) × 50.5(H) ㎜
Dimension T38N
HANYOUNGNUX CO.,LTD ※ It’s necessary to use Panel Mount Adaptor in Case of Panel Type
28, Gilpa-ro 71beon-gil, Nam-gu, Incheon, Korea TEL : (82-32)876-4697 FAX : (82-32)876-4696 T48N 48.0(W) × 48.0(H) ㎜
PT. HANYOUNG ELECTRONIC INDONESIA 01 1 sec, 1 min or 1 hour max. selectable
JL.CEMPAKA BLOK F 16 NO.02 DELTA SILICON II INDUSTRIAL PARK LIPPO CIKARANG CICAU,
CIKARANG PUSAT BEKASI 17550 INDONESIA TEL : 62-21-8911-8120~4 FAX : 62-21-8911-8126 03 3 sec, 3 min or 3 hour max. selectable
06 6 sec, 6 min or 6 hour max. selectable
Time range
10 10 sec, 10 min or 10 hour max. selectable
Safety information (set with dip witch)
30 30 sec, 30 min or 30 hour max. selectable
Alerts declared in the manual are classified to Danger, Warning and Caution by their criticality 60 60 sec, 60 min or 60 hour max. selectable
DANGER DANGER indicates an imminently hazardous situation which, if not avoided, wil result in death or serious injury 12 12 hour, 24 hour or 48 hour max. selectable
WARNING WARNING indicates a potential y hazardous situation which, if not avoided, could result in death or serious injury A Time-limit : contact 1c, instantaneous : contact 1a
CAUTION CAUTION indicates a potential y hazardous situation which, if not avoided, may result in minor or moderate injury Control output B Time-limit : contact 1c, instantaneous : contact 1c
C Time-limit : 2 x contact 1c
DANGER
None 24 - 240 V a.c./d.c. 50 - 60 Hz
Do not touch or connect any undesirable conductive part to input/output terminal since there is a possibility of electric shock. Power supply voltage
12 12 V d.c. (Only for T48N, Option)
WARNING None On-Delay
Output mode
•Please install an appropriate protective circuit on the outside if malfunction, an incorrect operation or S Interval (Option)
failure of the product may be a cause of leading to a serious accident and plan for preventing accidents.
•After mounting the product onto a panel, please use a socket dedicated to the product when connecting
with other units and do not turn on the power until completing wiring to prevent electric shock.
Part and function
•Please turn off the power when mounting/dismounting of the product. This is a cause of electric shock,  T38N  T48N
malfunction, or failure.
•If the product is used with methods other than specified by the manufacturer, then it may lead to injury or
property damage.
•In order to use this product properly and safely, we recommend periodic maintenance.
•The warranty of this product (including accessories) is 1 year only when it is used for the purpose it was
intended under normal condition.
CAUTION ① UP LED After time reaches “Set Time”, UP LED is ON when the time-limit output is operating.
•Please do not set “Time” to “0”. This can be a cause of malfunction. Also, there could be a time ② ON LED When the power is being supplied, ON LED is flashing Also, ON LED is ON when the time-limit output is operating.
difference in timer operation. Please use it after confirming the time difference.
③ Time setting Time setting knob. “Time” can be changeable during operation
•Please set or change “Time Range” in the dip switch while the timer is OFF. If the “Time Range” has
been changed to other value during the operation, please turn off the timer and turn it back on. It has s(second), m(minute) and h(hour) and can be selected arbitrarily.
•Since this is not explosion-proof structure, please use in a place where corrosive gas ④
(but, it can be changed only when the power is OFF.)
(such as harmful gas, ammonia, etc.), combustible or explosive gas does not occur.
•Please use in a place where there is no direct vibration and a large physical impact to the product.
•Please use in a place where there is no water, oil, chemicals, steam, dust, salt, iron or others Appearance and Panel cutout [unit : mm]
•Please avoid using in a place where excessive amounts of inductive interference or electrostatic and
magnetic noise occur.  T38N  T48N
•Please avoid using in a place where heat accumulation occurs due to direct sunlight or radiant heat.
•Please use in a place where the elevation is below 2,000 m. m

•Please make sure to inspect the product if exposed to water since there is a possibility of electric leakage
or a risk of fire.
•If there is a lot of noise from the power line, installing an insulated transformer or a noise filter is recommended.

min
min
•When the power is being supplied there should be a preparation time for the contact output.
Please use a delay relay together when it is used as a signal on the outside of interlock circuit or others.
● T38N (With Panel Mount Adapter)
Specification ● T48N Bracket ● Panel cutout
Power supply voltage 24 - 240 V AC 50 - 60 ㎐, 24 - 240 V DC, 12 V DC (Option) min

Allowable voltage Power supply voltage ±10 % min

Power consumption 4.5 VA max (240 V AC 60 Hz), Approx. 1.5 W max (24 V DC)
Power reset time 0.1 s max
min
min

Time range ※ Refer to suffix code

Time Repeat error ±0.3 % max (percentage of full scale)
difference Setting error ±5 % max (percentage of full scale) ● T38N adapter ● Panel cutout
Output mode POWER ON DELAY, INTERVAL (Option)
Control Contact A type (time-limit 1c + instantaneous 1a) /
output composition B type (time-limit 1c + instantaneous 1c) / C type (time-limit 2c)
Contact capacity 250 V AC 3 A resistive load
Relay life span Mechanical : 10 million times min / Electrical : 100 thousand times min
Dielectric strength 2000 V AC 60 Hz for 1 min (Between two different current carrying parts)
±2 kV (between power terminal, pulse width ±1㎲,
Noise immunity
Output operation
set time Power reset set time
square wave noise by noise simulator) Power
Power
set time Power
time reset set time
time
Instantaneous contact (NO)
Insulation resistance 100 MΩ min (500 V DC) Instantaneous contact (NO) set time Power reset set time
 A type Power
Time-limit (NC)
Time-limit (NC)
time

Vibration resistance (durability) 10 – 55 Hz (for 1 min), amplitude 0.5 mm, for 3 direction for 2 hr Instantaneous contact (NO)
(time-limit 1c + instantaneous 1a) Time-limit (NO)
Time-limit (NO)
Time-limit (NC) min Operation indicator
Shock resistance (durability) 300 ㎨ for each 3 direction for 3 times min Operation
min indicator
min
Time-limit (NO) Power on indicator
Power on indicator
Operating ambient temperature -10 ~ 50 ℃ (without condensation) min Operation indicator
min
Power on indicator
Operating ambient humidity 30 ~ 85 % R.H.
min

set time Power reset set time

min

Power
min

min

set time time reset set time

Power
Storage temperature -20 ~ 65 ℃  B type Power
Instantaneous contact (NC)
time
Instantaneous contact (NC) set time Power reset set time
Certification (time-limit 1c + instantaneous 1c) Power
min

Instantaneous contact (NO) time

min

Instantaneous contact (NO)

Instantaneous contact (NC)
Time-limit (NC)
Time-limit (NC)

Connection diagram Instantaneous contact (NO)

Time-limit (NO)
Time-limit (NO)
Time-limit (NC) Operation indicator
Operation indicator
 A type  B type  C type Time-limit (NO) Power on indicator
Power on indicator
Operation indicator
set time Power reset set time
 C type (time-limit 2c) Power
Power
Power on indicator set time Power
time reset set time
time
Time-limit (NC) Power reset set time
Time-limit (NC) set time
Power time
Time-limit (NO)
Time-limit (NC)
Time-limit (NO)
operation indication
Time-limit (NO) operation indication
indication of sending
indication
the electricofcurrent
sending
operation
the electricindication
current
※ Above charts are On-Delay operations. In the Interval operation,
indication of sending Time-limit operates conversely.
the electric current