ML0201KE170213

Analog multi timer HANYOUNGNUX CO.,LTD

MA4N
1381-3, Juan-Dong, Nam-Gu Incheon, Korea.
HEAD OFFICE TEL:(82-32)876-4697
FAX:(82-32)876-4696
http://www.hynux.net
INSTRUCTION MANUAL
PT. HANYOUNG ELECTRONIC INDONESIA
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered. INDONESIA Jl. cempaka blok F16, No.02 Delta Silicon II
Before using the product, please read this instruction manual carefully. FACTORY Cikarang Bekasi Indonesia
TEL : 62-21-8911-8120~4
Please keep this manual where you can view at any time FAX : 62-21-8911-8126

Safety information Suffix code

Before using the product, please read the safety information thoroughly and use it properly.
Model Code Description
Alerts declared in the manual are classified to Danger, Warning and Caution by their criticality
MA4N - ☐ Analog multi timer (48 × 48 ㎜)
DANGER indicates an imminently hazardous situation
DANGER which, if not avoided, will result in death or serious injury
A 2c (Time limit) ※ 11 pin type
Device B 2c (Time limit + Instantaneous) ※ 11 pin type
WARNING indicates a potentially hazardous situation selection
WARNING which, if not avoided, could result in death or serious injury C
2c (Time limit), 2c (Time limit + Instantaneous)
※Processed by mode selection (8pin type)
CAUTION indicates a potentially hazardous situation which, Power supply voltag 24 - 240 V a.c / d.c (50 - 60 ㎐) Dual usage
CAUTION if not avoided, may result in minor or moderate injury

DANGER
Specification
There is a danger of occurring electric shock in the input/output terminals so Model MA4N-A MA4N-B MA4N-C
please never let your body or conductive substance is touched. Power Supply voltage 24 - 240 V a.c / d.c 50 - 60 ㎐

Voltage regulation ±10 % from supply voltage

WARNING
• If there is a possibility of an accident caused by errors or malfunctions of this Power consumption 5.3 VA (240 V a.c), 2.5 W (240 V d.c)
product, install external protection circuit to prevent the accident. Resetting time 0.1 sec max
• This product does not contain an electric switch or fuse, so the user needs to
START
install a separate electric switch or fuse externally. (Fuse rating: 250V 0.5A) Input
• To prevent defection or malfunction of this product, supply proper power Min
INHIBIT
voltage in accordance with the rating. Signal 20 ms min -
Input
• To prevent electric shock or malfunction of product, do not supply the power length
RESET
until the wiring is completed. Input
• Since this product is not designed with explosion-protective structure, do not START
use it any place with flammable or explosive gas. Input Non voltage Input
• Do not decompose, modify, revise or repair this product. This may be a Input INHIBIT Impedance in a short circui t : 2 ㏀ max
-
cause of malfunction, electric shock or fire. condition Input Residual voltage in a short circuit : 0.7 V d.c max
• Reassemble this product while the power is OFF. Otherwise, it may be a RESET Impedance in open : 100 ㏀ min
cause of malfunction or electric shock. Input
• I f you use the product with methods other than specified by the Time limit 2c
Time limit 1c
manufacturer, there may be bodily injuries or property damages. Time limit 2c
Instantaneous 1c
Time limit 1c
•Due to the danger of electric shock, use this product installed onto a panel Output Instantaneous 1c
while an electric current is applied. N.O : 10 A 125 V a.c, 5 A 250 V a.c, 5 A 30 V d.c
N.C : 3 A 125 V a.c, 2 A 250 V a.c, 1 A 30 V d.c
CAUTION Setting error ± 5 % ±0.05 sec max
• The contents of this manual may be changed without prior notification. Repeat error ± 0.3 % max
•B  efore using the product you purchased, make sure that it is exactly what you ordered.
• Make sure that there is no damage or abnormality of the product during delivery. Temperature error ± 2 % max
• Do not use this product at any place with corrosive
Insulation resistance 100 ㏁ min (Base on 500 V d.c)
(especially noxious gas or ammonia) or flammable gas.
• Do not use this product at any place with direct vibration or impact. Dielectric strength 2000 V a.c 50 / 60 ㎐ for 1 min
• Do not use this product at any place with liquid, oil, medical substances,
dust, salt or iron contents. Impulse voltage ±2000 V max
• Do not polish this product with substances such as alcohol or benzene. Mechanical
10 - 55 ㎐ double amplitude 0.75 ㎜
• D o not use this product at any place with a large inductive difficulty or durability
Vibration
occurring static electricity or magnetic noise. Malfunction
durability 10 - 55 ㎐ double amplitude 0.5 ㎜
• Do not use this product at any place with possible thermal accumulation due Mechanical
to direct sunlight or heat radiation. durability 300 ㎨ (Approx. 30 G)
• Install this product at place under 2,000 m in altitude. Shock
Malfunction
100 ㎨ (Approx. 10 G)
• When the product gets wet, the inspection is essential because there is a durability
danger of electric leakage or fire. Mechanical Over 10 million operations (Open & Short frequency : 180 / min)
Life
• I f there is excessive noise from the power supply, using insulating expectancy  Electrical
transformer or noise filter is recommended. The noise filter must be attached Over 100,000 (250 V a.c 3 A load resistance)
to a panel which is already connected to a ground and the wire between the Terminal type Socket type 11 Pin Socket type 8 Pin
filter output and power supply terminal must be as short as possible.
• If puttig power cables closely together then It is effective against noise. Ambient
-10 ~ 55 ℃ (With no condensation)
temperature
• Do not connect anything to the unused terminals.
• After checking the polarity of terminal, connect wires at the correct position. Conservation
-20 ~ 65 ℃ (With no condensation)
temperature
• When this product is connected to a panel, use a circuit breaker or switch
approved with IEC60947-1 or IEC60947-3. Ambient humidity 35 ~ 85 %R.H.
• Install the circuit breaker or switch at near place for convenient use.
Weight About 100g (Including fixing bracket)
• Write down on a label that if the circuit breaker or switch is operating then
the power will be disconnected since the circuit breaker or switch is installed.
• F or the continuous and safe use of this product, the periodical maintenance is recommended.
•S  ome parts of this product have limited life span, and others are changed by their
• T he warranty period for this product including parts is one year if this product is properly used.

5
Time range Dimension and panel cutout
[unit : mm]
Time unit
sec min hrs ×10h
Max time
1.2 0.12 ~ 1.2 1.2 ~ 12

Setting 3 0.3 ~ 3 3 ~ 30
range 12 1.2 ~ 12 12 ~ 120

30 3 ~ 30 30 ~ 300

Part name

█ External connection
Please select operation mode by turning of operation mode switch in
front of panel.
User can select 6 types of operation modes Operation mode is
displayed as like
A, B, C, D, E, F or A1, B1, C1, D1, E1, F1.

Connection diagram
█ MA4N-A / MA4N-B

·MA4N-A : Two relay work as Time limit.

·MA4N-B : The relay connected ①, ③,
④work as Instantaneous and othr realys
work as time limit.
※ Please refer to Timing charts for working
of relays

█ Selection of time unit

Please select time by turning of Time range switch
Use can select 16 types of time ranges and it is displayed as like sec,
min, hrs, 10h
█ MA4N-C

·Two relays in Mode A1 and D1 work as

Time limit.
·The relays in Mode B1, C1, E1, F1
connected ①, ③, ④ work as
Instantaneous.
And other realys work as time limit.
※ MA4N-C : According to timing charts,
relays works as Time limit or
Instantaneous.
※ Please refer to Timing charts for
working of relays.

6
Timing charts (MA4N-A, MA4N-B)
※ MA4N-A : Output – Time limit 2c   MA4N-B : Output – Time limit 1c, Instantaneous 1c

A MODE: ON DELAY

Power ②-⑩

Start ②-⑥

Reset ②-⑦

①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

B MODE: FLICKER OFF START

Power ②-⑩

Start ②-⑥

Reset ②-⑦

①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

C MODE: INTERVAL

Power ②-⑩

Start ②-⑥

Reset ②-⑦

①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

D MODE: SIGNAL ON / OFF DELAY

Power ②-⑩

Start ②-⑥

Reset ②-⑦

①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

E MODE: SIGNAL OFF DELAY

Power ②-⑩

Start ②-⑥

Reset ②-⑦
①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

F MODE: FLICKER ON START

Power ②-⑩

Start ②-⑥

Reset ②-⑦

①-④
Time-Limit contact N.C
⑪-⑧
①-③
Time-Limit contact N.O ⑪-⑨

Operation / Conducting display LED

7
Timing charts (MA4N-C)
※ t : Setting time, t-a: Within setting time, Rt: Resetting time

A1 MODE : ON DELAY

Power ②-⑦
①-④
Time-Limit contact N.C
(⑧-⑤)
①-③
Time-Limit contact N.O
(⑧-⑥)

Time-Limit output operation display LED

Operation / Conducting display LED

B1 MODE : ON DELAY 1 (One-shot output)

Power ②-⑦

Time-Limit contact N.C ⑧-⑤

Time-Limit contact N.O ⑧-⑥

Instantaneous contact N.C ①-④

Instantaneous contact N.O ①-③

Time-Limit output operation display LED

Operation / Conducting display LED

※ The Output width of one shot is fixed by 0.5 second

C1 MODE : ON DELAY2

Power ②-⑦

Time-Limit contact N.C ⑧-⑤

Time-Limit contact N.O ⑧-⑥

Instantaneous contact N.C ①-④

Instantaneous contact N.O ①-③

Time-Limit output operation display LED

Operation / Conducting display LED

D1 MODE : FLICKER OFF START

Power ②-⑦

①-④
Time-Limit contact N.C
(⑧-⑤)
①-③
Time-Limit contact N.O
(⑧-⑥)
Time-Limit output operation display LED

E1 MODE : FLICKER ON START

Power ②-⑦

Time-Limit contact N.C ⑧-⑤

Time-Limit contact N.O ⑧-⑥

Instantaneous contact N.C ①-④

Instantaneous contact N.O ①-③

Time-Limit output operation display LED

Operation / Conducting display LED

F1 MODE : INTERVAL

Power ②-⑦

Time-Limit contact N.C ⑧-⑤

Time-Limit contact N.O ⑧-⑥

Instantaneous contact N.C ①-④

Instantaneous contact N.O ①-③

Time-Limit output operation display LED

Operation / Conducting display LED

※ We suggest over 100 ms of Min. setting time for D1, E1 output mode because excessive short setting time may cause of malfunction.