2 - KMC-650 Service Manual - Eng - V1
2 - KMC-650 Service Manual - Eng - V1
2 - KMC-650 Service Manual - Eng - V1
Service Manual
Ver. 1.3
1
KMC-650 Service Manual V1.3
This manual may not be reproduced, in whole or in part, without the written permissions of
GEMSS MEDICAL, Inc.
The material in this manual is provided for informational purposes only and is subject to
change without notice.
KMC-950 is a trademark of GEMSS MEDICAL, Inc. In the USA and other countries. Other product and
company names mentioned herein are the property of their respective owners.
This manual contains descriptions, instructions, and procedures which apply only this product.
2
KMC-650 Service Manual V1.3
1. SPECIFICATION
SYSTEM POWER REQUIREMENTS 6
ENVIRONMENT 6
X – RAY COLLIMATOR 6
TUBE NAME 7
VOLTAGE RANGE
FOCAL SPOT
FILAMENT CURRENT
FILAMENT VOLTAGE
ANODE LOADING
TARGET ANGLE
TARGET MATERIAL
INHERENT FILTRATION
WEIGHT
C-ARM 10
TV CAMERA 11
XTV MONITOR 11
IMAGE INTENSIFIER 13
ACCESSORIES 13
3
KMC-650 Service Manual V1.3
2. SERVICE DATA
SYSTEM CIRCUIT DIAGRAM 14
Board Layout 18
Main board 18
Fuse board layout 21
Psu board layout 23
X-Ray CHECK 24
SETUP 36
SETUP MENU 37
BUZZ select 38
IRIS Value set 39
4
KMC-650 Service Manual V1.3
3. WORKSTATION
HARDWARE OVERVIEW -------------------------------------------------- 112
Location ----------------------------------------------------------------------------------- 112
Parts location ----------------------------------------------------------------- 113
Connecting the Cables ---------------------------------------------------- 114
5
KMC-650 Service Manual V1.3
1. SPECIFICATION
SYSTEM POWER REQUIREMENTS
LINE VOLTAGE : ~220 - 230 VAC 50/60 Hz : for UL
LINE PHASE : SINGLE
INPUT POWER : 3000 VA @ 220 VAC
LINE CODE : 26.3FT
LINE PLUG : 250 VAC, 38A LEGRAND NO. LV-38A-58700
ENVIRONMENT
OPERATIONAL : 10°C~40°C, 30~75% rH
STORGE : 0°C~45°C, 10~85% rH
Extended Storage and Transportation > 2 days: 5 ~ 40°C, 5 ~ 90%RH
Short-term Storage and Transportation < 2 days: 0 ~ 45°C, 5 ~ 90%RH
6
KMC-650 Service Manual V1.3
X-RAY TUBE HEAD ASSEMBLY
TUBE NAME: TOSHIBA DF-151SBR
VOLTALGE RANGE
FLUORO. : 40 - 110 kV
RAD.: 40 - 100 kV
TUBE CURRENT MAXIMUM
LARGE FOCUS: 20 mA
SMALL FOCUS: 4.0mA
FOCAL SPOT
LARGE FOCUS: 0.5 mm
SMALL FOCUS: 1.5 mm
MAXIMUM FILAMENT CURRENT
LARGE FOCUS: 4.3 A
SMALL FOCUS: 3.1 A
FILAMENT VOLTAGE
LARGE FOCUS: 5.0 – 6.4V
SMALL FOCUS: 3.5 – 4.9V
ANODE HEAT STORAGE 45 KHU
ANODE HEAT COOLING 786/SEC
ANODE LOADING
LARGE FOCUS: 3000W @ SINGLE 1.0S EXP.
SMALL FOCUS: 680W @ SINGLE 1.0S EXP.
ANODE RPM STATIONARY
TARGET ANGLE 16°
INHERENT FILTRATION ≥0.8 mm AL @ 50 kV
TUBE WEIGHT 1.25 kg
TUBE ASSEMBLY WEIGHT 24 kg
7
KMC-650 Service Manual V1.3
X-RAY GENERATOR
LINE VOLTAGE: 110 VAC
1 PHASE
LINE FREQUENCY: 50 / 60 Hz
OUTPUT POWER : < 3.0 KW @ 220 VAC
kV RANGE FLUORO: 40 – 110 kV
kV RANGE RAD: 40 – 100 kV
kV ACCURACY : ± 7%
KV INCREMENTS: DIGITAL UP/DOWN 1 kV STEPS
mAs RANGE: 8 mAs – 100 mAs 22 Step
mAs ACCURACY : ± 20% FLUORO. ONLY
mA RANGE FLUOR: 0.5 – 4.0 mA
mA RANGE SNAPSHOT 8.0 mA FIXED
mA RANGE BOOST: 20 mA FIXED MAX. 3 SEC.
mA INCREMENTS MANUAL:0.1 mA STEP
mA INCREMECTS ABC: 0.5 – 4.0 mA @ 40 – 110 kVP
EXP. TIME RANGE: 0.002 – 5.0 SEC.
EXP. TIME ACCURACY: ± 20%
INVERTER FREQUENCY : 20 kHz
8
KMC-650 Service Manual V1.3
C-ARM AND STAND MECHANICAL
OVERALL SIZE AND WEIGHT
HEIGHT : 1770mm
WIDTH : 800mm
LENGTH : 1830mm
WEIGHT : 300kg
FREE SPACE : 797mm
DEPTH : 692mm
9
KMC-650 Service Manual V1.3
C-ARM
ORBIT.ROTATION : 135 DEGREES
HORIZ.TRAVEL : 200mm
VERT.TRAVEL : 500mm"
SID Fluoro : 1000mm RAD : 970mm
☞ The size of X-Ray field does not differ from markings by more than 2% from the FOCAL SPOT
PANNING : ± 12.5 DEGREES
ROTATION : ± 180 DEGREES
10
KMC-650 Service Manual V1.3
TV CAMERA
NAME (type): LUNA1K
CCD SCANNING: InterlineTransfer CCD; progressive scan with microlenses
NUMBER OF ACTIVE PIXELS :1024(H) x 1024 (V) pixels
CCD Type 1/2” Interline Anti-blooming CCD sensor
Integrated optical lens High resolution with adjustable focus and diaphragms & iris
A/D converter 14 Bit
SIGNAL PROCESSING 16 Bit Digital signal processing
LIH Image rotating
Image reverse
Circular blanking
Edge enhancement
Noise Reduction
INTERFACES Video output: Camera link
Camera control interface: RS-232
LENS MOUNT C-MOUNT
POWER SUPPLY: 24Vdc ± 20%
OPERATION CONDITIONS
Working temperature -10°C to + 45°C
Store temperature -40°C to + 55°C
Humidity Operating to 95% relative humidity (non-condensing)
XTV MONITOR
MODEL MM-190
MANUFACTURER MEDITECH
TYPE B/W TFT Active Matrix LCD
POWER SUPPLY 230VAC±15%, 115VAC±15%
MONITOR SIZE: 19”
ASPECT: 5:4 (1280 x 1024)
BRIGHTNESS: 1,000cd/ (Center 1-Point, typ)
VIEWABLE ANGLE: R/L/U/D 85/85/85/85 (Min)
11
KMC-650 Service Manual V1.3
Another Type
XTV MONITOR( Conforms to EN60601-1/EN60950, EN60601-1-2 )
MODEL NF17F6AAD
MANUFACTURER NICAL SPA
POWER SUPPLY 230VAC±15%, 115VAC±15%
MONITOR SIZE: 17”
READOUT: FRAME
SCANNING LINES: 525LINE/60Hz
SCANNING SYSTEM: 2 : 1 INTERLACED
PICKUP DEVICE: 1/2 INCH CCD CAMERA
12
KMC-650 Service Manual V1.3
IMAGE INTENSIFER
( Conforms to EN60601-1:1993, EN60601-1-2:, IEC1262-1 to 7 : 1994 )
NAME : THALES TH 9428 HP2
INPUT SCREEN DIAMETER : 230/160/120 mm
OUT SCREEN DIAMETER : 20±0.5 mm
DQE : 65%
(Detective Quantum Efficiency)
RESOLUTION : 56 lp / Cm
CONTRAST : 25 / 1
CONVERSION FACTOR : 120 (cd / m2)
ACCESSORIES
The accessories delivered with the basic configuration of the KMC-650 consist of :
13
KMC-650 Service Manual V1.3
2. SERVICE DATA
System Circuit Diagram
14
KMC-650 Service Manual V1.3
X-RAY Generator Block Diagram
CN103 CN202
+24V
1 +15V 1
2 -15V 2
3 GND 3
4 GND 4
5 5
53258-5 53258-5
TO SYSTEM
15
KMC-650 Service Manual V1.3
Error Code
If there occurs a specific error in the machine, an appropriate error message will be displayed
on the graphic KVP DISPLAY for easy identifiability:
E 04 NOT USED
16
KMC-650 Service Manual V1.3
17
KMC-650 Service Manual V1.3
BOARD LAYOUT
MAIN B/D LAYOUT
CAMERA COM
CN19 JP4,5 SELECTOR
CN15 CN16
SW3
touch
CN4
CN11
CN18
CN3
CN2
CN9
TEMP_JP3
NOT USE
CN20 CN14
CN21 CN5
CN6
CN7
CN22
CN8
18
KMC-650 Service Manual V1.3
Main Board Connector
All connector
PCB point
No. 1 1
#1 CN 1 DC POWER
#2 CN 2 HFG INTERFACE
#4 CN 4 INTERFACE BOARD
#5 CN 5 EMERGENCY S/W
# 10 CN 10 COLLIMATOR
# 11 CN 11 COLLIMATOR SENSOR
# 12 - - -
# 13 - - - -
# 14 CN 14 OP PANEL
# 15 CN 15 RS232 PC
# 16 CN 16 RS232 TOUCH
# 17 CN 17 TUBE OVERHEAT
#18 CN 18 ELEVATOR
#19 CN 19 LASER
19
KMC-650 Service Manual V1.3
DIP switch & JUMP factory setting
[ DIP switch 3 ]
DIP Switch 3
Switch 1 OFF
Switch 2 ON
Switch 3 ON
Switch 4 ON
20
KMC-650 Service Manual V1.3
FUSE B/D LAYOUT
F5 F4 F3 F2 F1
21
KMC-650 Service Manual V1.3
(2). HFG GENATOR DC POWER BOARD(PWR BOARD & DRIVER BOARD)
PSU BOARD
Fuse # 1 FUSE 1 3.15 A/250V
MAIN POWER
WARNING
- When you change fuse
1. You should check the rating, power, part no., and marking according with the manual.
2. It should be performed by an expert or an engineer who is well trained.
22
KMC-650 Service Manual V1.3
PSU B/D LAYOUT
CONNECTOR
SPEC COMMENT REMARK
NO.
1 LIVE(220V) Ac input terminal
CN1 2 NOT USED Ac input terminal
3 GROUND Earth
1 - 12 V DC
2 GND
3 + 24 V DC
4 GND
5 + 12 V DC
CN2 Input main board
6 + 12 V DC
7 GND
8 GND
9 + 5 V DC
10 + 5 V DC
1 - 12 V DC
2 GND
3 + 24 V DC Input Op board
4 GND
5 + 12 V DC
CN3
6 + 12 V DC
7 GND
8 GND
9 + 5 V DC
10 + 5 V DC
23
KMC-650 Service Manual V1.3
X-Ray CHECK
MAIN BOARD REFERENCE SIGNAL
This procedure is the adjustment and check job within Main Board. (KM9EEXT005)
24
KMC-650 Service Manual V1.3
25
KMC-650 Service Manual V1.3
MAIN BOARD SCOPE SIGNAL
26
KMC-650 Service Manual V1.3
27
KMC-650 Service Manual V1.3
X-Ray GENERATOR
This procedure is the adjustment and check job within HFG Control Inverter Unit (KM6EEXT005)
and High Voltage Tank Unit (KM6MEEXT005-4) for X-RAY generation.
There will be few cases in which the following checking and tuning of HFG unit is needed in the field. If you want to
check the details of HFG, you should uncover the back and left side cover of KMC-650 and then uncover the HFG
Inverter unit in the left side. Appropriate measurement devices, such as oscilloscope, DMM (Digital Multi Meter) etc.
are required to check the signals.
WARNING
- To avoid the electrical shock, you should be very cautious in dealing the high voltage
connectors (Anode, Cathode) on tank and tube. Even after the main power is down,
high voltage charge still remains in tank and tube for about a few minutes.
- High voltage connectors should be always tightly fastened before the main power is
turned on.
28
KMC-650 Service Manual V1.3
Functional Blocks for X-RAY generator of KMC-650
CN103 CN202
+24V
1 +15V 1
2 -15V 2
3 GND 3
4 GND 4
5 5
53258-5 53258-5
TO SYSTEM
29
KMC-650 Service Manual V1.3
MONOTANK DRIVE BOARD FEEDBACK SIGNAL OF KMC-650
30
KMC-650 Service Manual V1.3
31
KMC-650 Service Manual V1.3
32
KMC-650 Service Manual V1.3
RADIATION MEASUREMENT DATA
33
KMC-650 Service Manual V1.3
Move the RAD Mask on the x-ray tube to focus X-Ray to center after x-ray calibration.
Method:
1. Set to Fluoro mode of 60KV, 3mA (or RAD mode, 40KV, 30mAs).
2. Stick the fluorescent plate on the I.I.
3. Make environment dark to watch the fluorescent.
Use the protector or black curtain. - Dark room is also useful.
4. Move RAD Mask so that the circle A on the fluorescent plate is
placed to center of X-Ray Beam.
(Fluorescent plate)
34
KMC-650 Service Manual V1.3
X-RAY Filed Size of KMC-650
35
KMC-650 Service Manual V1.3
SETUP
1. SETUP MENU
For the open Setup mode is pushed “kvp up button” and “memory down button”.
36
KMC-650 Service Manual V1.3
BUZZ select
Procedure
37
KMC-650 Service Manual V1.3
Iris value set.(option: only Iris Collimator)
Procedure
4. Selector ZOOM3
5. Adjust value
6. Go to 5. Adjustment(Repeat)
7. And pushed “store button”.(The end)
38
KMC-650 Service Manual V1.3
39
Service Manual
1-40
Service Manual
1-41
Service Manual
2. C-ARM AND I.I. ASSEMBLY
1-42
Service Manual
ITEM NO. PART NO. UNIT NAME QTY. DESCRIPTION
1 KM9MSTA001 STAY 1
2 KM9MCAR001 C-ARM 1
3 Fig. 4 Image Intensifire 1
1-43
Service Manual
3. C-ARM SYAY STOPPER ASSEMBLY
6
5
4
S1
3
8
S3
2
7
S2
1-44
Service Manual
1.
1-45
Service Manual
4. MOTOR, CCU AND HFG PART ASSEMBLY
1-46
Service Manual
1-47
Service Manual
5. IMAGE INTENSIFIER AND CAMERA HEAD ASSEMBLY(9”)
1-48
Service Manual
1-49
Service Manual
6. IMAGE INTENSIFIER POWER SUPPLY ASSEMBLY(9”)
1-50
Service Manual
1-51
Service Manual
7. C-ARM ROTATION LOCK ASSEMBLY
1-52
Service Manual
1-53
Service Manual
8. C-ARM ORBIT REVOLUTION LOCK ASSEMBLY
1-54
Service Manual
1-55
Service Manual
9. C-ARM SLIDING BEARING ASSEMBLY
1-56
Service Manual
1-57
Service Manual
10. TUBE COVER ASSEMBLY
1-58
Service Manual
1-59
Service Manual
1-60
Service Manual
1-61
KMC-650 Service Manual V1.2
11. CART ACCESSORIES ASSEMBLY
62
KMC-650 Service Manual V1.2
63
KMC-650 Service Manual V1.2
12. CART MONITOR & CYLINDER ASSEMBLY
64
KMC-650 Service Manual V1.2
65
KMC-650 Service Manual V1.2
13. CART COVER ASSEMBLY
66
KMC-650 Service Manual V1.2
67
KMC-650 Service Manual
CCD camera
Counterweight
Image intensifier
Service Manual
INTRODUCTION
TH 9428 HP2 H211 VR13 is a triple field X-Ray Image Intensifier for medical applications
with a nominal entrance field size of 230 mm and an output image diameter of 20 mm.
Its main components are:
-X-Ray Image Intensifier tube
-mu metal magnetic shield
-lead radiation shield
-painted housing: Thales color reference: T23
-power supply: HV type TH 7195
Technical Specification ref. TS 4989-161 and
User’s Manual TIV/1M.1166/96
PARTICULAR FEATURES
Environmental data
With the maximum allowed static load on the output flange (see outline drawing) the mechanical
shocks should not exceed 1 g (6 ms duration).
REGULATORY REQUIREMENTS
DHHS 21 CFR 1020-30 IEC 60601-1; IEC 60601-1-2 UL 2601 CSA 22-2 n° 60601-1
Marking: CE, UL
69
KMC-650 Service Manual
70
KMC-650 Service Manual
ELECTRO-OPTICAL TS 61 417 355
CHARACTERISTICS TH 9428 HP2 H211 VR13
X RAY IMAGE INTENSIFIER 2003-11-27 Page 3
Average background luminance
The average background luminance shall be less than 0.02 cd/m² in all modes.
Just after switching on, or after switching modes, the XRII may exhibit some local luminance
fluctuations.These momentary fluctuations should not exceed 0.1 cd/m² and normally disappear after a
few minutes.
Image shift
The center of the entrance field in the magnifying modes should not shift more than 5 mm (typically 2
mm) with respect to the center of the entrance field in the normal mode of operation.
Output screen spectral response
The output screen contains a P20 type phosphor with a peak wavelength between 520 and 540 nm and a
full width at half maximum of less than 100 nm.
Optical
The thickness of the output window is 3.6 ± 0.2 mm.
The index of refraction of the output window is 1.50 ± 0.02 at 587 nm
The distance of the image plane to the pilot plane will be everywhere within ± 30 µm from the value at
the
center of the image.
Rise and decay time
At an exposure rate of 5 mR/s in the normal mode the luminance of the output screen will be more than
50 % and more than 80 % of its final value respectively 1 ms and 10 ms after starting the exposure. After
a continuous exposure rate of 5 mR/s in the normal mode, the luminance of the output screen will be less
than 30 % and less than 10 % of its initial value respectively 1 ms and 10 ms after stopping the exposure.
Minimum pulse width (valid when used with THALES power supplies only) The minimum pulse width
per DSA pulse is typically 20 ms. The minimum pulse width per cine pulse is typically 2 ms.
Blanking mode
The output luminance of the image intensifier can be blanked to a level less than 5 % (typically 1 %)
with respect to the unblanked mode in all fields, by applying a blanking signal to the power supply
unit. The blanking time constant is less than 1 ms.
71
KMC-650 Service Manual
Operating voltage
* for optimum performances U1 and U2 should be adjusted for each mode.
Maximum electrical ratings
XRII maximum input voltages UPC = 1200 V (blanking)
U1 = 350 V
U2 = 1.5 kV
U3 = 13 kV
U4 = 3.5 kV
U5 = 31 kV
Photocathode maximum continuous current IPC = 5 µA
Photocathode maximum pulsed current IPC = 50 µA
Environmental data
The detailed description of the environmental testing conditions is given in TII/4.100/90.
The main characteristics are summarized hereunder :
- climatic
-operating temperature range +5°C to + 40°C
-storage temperature range -10°C to + 55°C
72
KMC-650 Service Manual
73
KMC-650 Service Manual
74
KMC-650 Service Manual
75
KMC-650 Service Manual
1. CCD CAMERA
1.1 Camera power supplay
76
KMC-650 Service Manual
Power board
Remove 3 screws
Camera removal
Camera connections
77
KMC-650 Service Manual
The camera is put onto the output window and is fixed by the mounting ring using 3 screws.
78
KMC-650 Service Manual
Locking screw(3)
for focusing ring
focusing ring
Locking screw(3)
for zoom
79
KMC-650 Service Manual
80
Service Manual
- PARTⅠ. SCHEMATIC -
1-81
Service Manual
1) KMC-650 OP board
1-82
Service Manual
U31F
CN4
U5
AD0 2 19 SA0 SD[ 0.. 7] SD[ 0. .7] 13 12 C CU_FUNCTION 0 1
+12V AD1 3 D0 Q0 18 SA1 74LS07 14
+5V AD2 4 D1 Q1 17 SA2 C CU_FUNCTION 1 2
AD3 5 D2 Q2 16 SA3 U31B 15
AD IN7 AD4 6 D3 Q3 15 SA4 3 4 C CU_FUNCTION 2 3
74HC573
AD5 D4 Q4 SA5 +5V 74LS07 FD_CC U
+5V R6 +5V 7 14 16
R2 AD6 8 D5 Q5 13 SA6 C CU_FUNCTION 3 4
AD7 D6 Q6 SA7 AR4 U31E VD_CCU
U21 4. 7K 1K 9 12 17
2
R4 D7 Q7 1 XU3 U10 11 10 CC U_SUB 0 5
R
2 6 3 VR 1 1 ALE 11 2 SA0 SA0 10 11 SD0 SD0 2 19 74LS07 18
4. 7K RESI N RST 5 D1 1 LE 3 SA1 SA1 9 A0 O0 12 SD1 SD1 3 D1 Q1 18 CC U_SUB 1 6
3 RST LM336_5V 10K VAR OE 4 SA2 SA2 8 A1 O1 13 SD2 SD2 4 D2 Q2 17 U31C 19
1 CT +5V + C14 74ALS573 5 SA3 SA3 7 A2 O2 15 SD3 SD3 5 D3 Q3 16 5 6 CC U_SUB 2 7
REF 8 0. 1uF 0. 1uF 6 SA4 SA4 6 A3 O3 16 SD4 SD4 6 D4 Q4 15 74LS07 20
VCC 10uF A4 O4 D5 Q5
+ C28 4 7 7 SA5 SA5 5 17 SD5 SD5 7 14 CC U_SUB 3 8
GN D SEN +5V SA6 SA6 A5 O5 SD6 SD6 D6 Q6 U31D
10uF 8 4 18 8 13 21
0.1uF C 27 U6 AR6 9 SA7 SA7 3 A6 O6 19 SD7 SD7 9 D7 Q7 12 9 8 9
TL7705A 1 AD8 25 A7 O7 D8 Q8 74LS07 22
R
0. 1uF AD0 2 18 SD0 SD0 2 AD9 24 A8 I OCS1 11 ACK_CCU/FR EEZE-B10
37
1
XU1 AD1 3 A1 B1 17 SD1 SD1 3 6. 8K AD10 21 A9 CLK U32C 23
+5V AD2 4 A2 B2 16 SD2 SD2 4 AD11 23 A10 OUT_EN 1 5 6 11
VPP
VCC
R5 AD3 5 A3 B3 15 SD3 SD3 5 AD12 2 A11 OE 74LS07 ABC 24
A4 B4 A12
74HC245
60 AD0 AD4 6 14 SD4 SD4 6 AD13 26 74HC574 12
+5V P3.0/ AD0 59 AD1 AD5 7 A5 B5 13 SD5 SD5 7 AD14 27 A13 U32D 25
P3.1/ AD1 AD2 AD6 A6 B6 SD6 SD6 A14
80C196KC20
10K 58 8 12 8 9 8 13
C10 U20 C12 3 P3.2/ AD2 57 AD3 AD7 9 A7 B7 11 SD7 SD7 9 SRD 22 74LS07
NMI P3.3/ AD3 AD4 A8 B8 CS_ROM 20 OE
+
22uF 2 1 22uF 56
+V C 1+ P3.4/ AD4 55 AD5 R D- 1 CE U32A CCU_DB25_FEMALE
+
3 16 P3.5/ AD5 54 AD6 19 DI R 6. 8K M27C256B 1 2 CCU_STROBO
C11 6 C1- 4 RESET P3.6/ AD6 53 AD7 OE 74LS07 1K_LP용 CUT
22uF -V C 2+ 22uF P3.7/ AD7 74HC245
+
+
CN16 5 C13 COL_LEAF_ROT_SV( ADIN0) 6 U32F
C2- ADI N1(m A F/ B) 5 ACH0/P0.0 52 AD8 XU4 U11 13 12 CCU _FR EEZE GATE
1 13 12 P2. 1 COL_LEAF_SV(TEMP_SV) 7 ACH1/P0.1 P4.0/ AD8 51 AD9 SA0 10 11 SD0 SD0 2 19 74LS07 1K_LP용 CUT
MWR
2 14 R 1 IN R1 OUT 11 P2. 0 ABC 4 ACH2/P0.2 P4.1/ AD9 50 AD10 SA1 9 A0 D0 12 SD1 SD1 3 D1 Q1 18
3 T1 OUT T1 IN FV++ 11 ACH3/P0.3 P4. 2/ AD10 49 AD11 SA2 8 A1 D1 13 SD2 SD2 4 D2 Q2 17 U32B
XU7
8 9 FV-- 10 P0. 4/ACH4 P4. 3/ AD11 48 AD12 AD9 1 12 SWR SA3 7 A2 D2 15 SD3 SD3 5 D3 Q3 16 3 4 CCU _R OT-CW
7 R 2 IN R2 OUT 10 COL_I RIS_SV 8 P0. 5/ACH5 P4. 4/ AD12 47 AD13 AD10 2 I0 F0 13 SRD SA4 6 A3 D3 16 SD4 SD4 6 D4 Q4 15 KEY _D 0 74LS07
EASY VIEW T2 OUT T2 IN ADI N7 9 ACH6/P0.6 P4. 5/ AD13 46 AD14 +5V AD11 3 I1 F1 14 CS_RAM SA5 5 A4 D4 17 SD5 SD5 7 D5 Q5 14 KEY _D 1
MAX232 ACH7/P0.7 P4. 6/ AD14 45 AD15 AD12 4 I2 F2 15 CS_ROM SA6 4 A5 D5 18 SD6 SD6 8 D6 Q6 13 KEY _D 2 U32E
P2.0 18 P4. 7/ AD15 AD13 5 I3 F3 16 SA7 3 A6 D6 19 SD7 SD7 9 D7 Q7 12 KEY _D 3 11 10 CCU _R OT-CCW
CN15 P2.1 17 P2. 0/TXD(out ) 43 AR7 AD14 6 I4 F4 17 AD8 25 A7 D7 D8 Q8 74LS07
1 VD 15 P2. 1/RXD(in) READY 65 1 AD15 7 I5 F5 18 C S_0 AD9 24 A8 I OCS2 11
R
2 OVER_H 44 P2. 2/EXIN T(in) CLKOUT 41 WR- 2 R D- 8 I6 F6 19 I ORW AD10 21 A9 CLK
3 42 P2. 3/T2CLK(in) BHE 40 WR- 3 WR- 9 I7 F7 AD11 23 A10 OUT_EN 1
HE_P2.5 39 P2. 4/T2RST(iN) WR 61 RD- RD- 4 11 I8 AD12 2 A11 OE
R3 +5V P2.6 33 P2. 5/PWM0(out) RD 62 ALE ALE 5 I9 AD13 26 A12 74HC574
DI S PC P2.7 38 P2. 6/T2Up-dOWM ALE 63 AD14 1 A13 SW3
16V8
P2. 7/T2Capture I NST A14
4.2K
4. 7K ACK_HI0 24 19 P1. 0 SRD 22
C? 25 HSI. 0 P1. 0 20 P1. 1 SWR 27 OE
104 FD_HI2 26 HSI. 1 P1. 1 21 P1. 2 CS_RAM 20 WE FV++
HI3 27 HSI. 2/HSO. 4 P1. 2 22 P1. 3 CS1
C4 HSI. 3/HSO. 5 PWM1/ P1. 3 23 P1. 4 24257AK-15
PWM2/ P1. 4 30 P1. 5
P1. 5
11. 0592
20 68
VCC 36 GND1 28 HO0 U8 1 SW DPDT/SM
R
27pF 1 14 GND0 HSO. 0 29 SA5 1 15 I OCS0 IOCS0 2 IOCS0 IOC S0
+5V RST/VPP Vss HSO. 1 A Y0
C3 2 34 SA6 2 14 I OCS1 IOCS1 3 IOCS1 I OCS1 ADD Part's
4 12 EA HSO. 2 35 +5V SA7 3 B Y1 13 I OCS2 IOCS2 4 IOCS2 I OCS2
XTAL2 ANGND HSO. 3 C Y2
A682G
5 12 I OCS3 IOCS3 5 IOCS3 I OCS3
X1
X2
XTAL1 AR2 AD8 Y3 I OCS4 IOCS4 6 IOCS4 I OCS4
1 6 11
G1 Y4
R
67
66
P1.0/AI N0 G2A Y5
R
3 P1.1 P1.1 13 2 80C 196KC20 ACK_H I0 2 CS_0 5 9 I OCS6 IOCS6 8 IOCS6 I OCS6 R89 +12V
P1.1/AI N1 P3. 0/RXD G2B Y6
6. 8K
1
HE_P2. 5 ACK VD FD
74HC125 SD[0.. 7] SD[0. .7] R87 100
VD FD _H I2 FD_CCU
C38
OVER_H +5V
+5V AR12
101 R86 100
AR1 1 U 14 VD VD_CCU
R
1 2 RTN0 RTN0 2 18 SD 0 C37
R TN 0
R TN 1
R TN 2
R TN 3
R TN 4
R TN 5
R TN 6
R TN 7
SCAN0
SCAN1
SCAN2
SCAN3
A1 Y1
R
10
11
12
13
14
1
2
3
4
5
6
7
8
9
8 A2 9 RTN7 RTN7 9 A7 Y7 11 SD 7
9 OVER_H 7 A8 Y8
WP 1 I OCS6
1K G1 19
6.8K G2
AT24C64 CN 14 74HC541
HI RO-14(OP PAN EL)
SHUTTER
+24V IRIS_COLLIMATOR
PREVIEW 패 턴 수 정
CN11
1
2
3
+12V로 변 경 4 I. I SELECTOR3 TP1
IRIS_COLLIMATOR CUT RED R ED CN3 I. I SELECTOR2 ?
1
+5V 연 결 D? SHUTTER6 R20 XU30A
COL_LEAF_ROT_SV( ADI N0)
3
-
+5V KBL06 D? ADI N0 1 4. 7K
8 1 RLY 1 + 3
5.6V
1 2 COL_IRI S_SV 부품 제거 +24V D2 LM324
5 3 4 1 5 U28 C? R99
1
2
3
4
C19
0.1u
C20
0.1u
+ C5
- + 3 1 16 SHU TTER6 47K
1B 1C
3300uF/ 35V
3300uF/ 35V
R16
1
+12V R95 R96 PA1A-24V 1N4007 R83 22K I. I SELECTOR 3 U12_13 6 5B 5C 11 I .I SELECTOR2 R23 XU30B
1
IRIS_COLLIMATOR CUT PREVIEW CUT 6B 6C
1N49371N4937 3K 3K U12_12 7 10 I .I SELECTOR3 1K - 6 R21
2 R84 22K I. I SELECTOR 2 7B 7C ADIN1(mA F/B) 7 4. 7K
3 U9 9 4.5 6 9 5
4 KSDA02 COM
+
C21
0. 1u
C23
0. 1u
5. 6V
5
+ C6 IRIS COLLIMATOR용 패턴 수정 RLY2 부품 제 거 SD0 2
D1 Q1
19 2 1 0 0 D3 LM324
100uF/ 35V 5 SD1 3 18 ULN2003A 3 1 1 0 C? R100
6 3 1N4007 SD2 4 D2 Q2 17
7 4 SD3 5 D3 Q3 16 0. 1u
47K CN2
1 D13 SD4 6 D4 Q4 15 U16 KVP_DATA 1
CON7 DIPSW2 D5 Q5
C22
0. 1u
C24
0. 1u
8
SDO
C26
0. 1u
C25
0. 1u
4
100uF/ 35V +5V 74HC595 3 + XU30D R27 13
1
1
U23
R19 R37 20K R61 10K 1 12 + 1K Kv 14
1
2
3
4
5
6
7
8
9
2 6 OU T_EN 1 2 - 14 15
4.7K RESIN RST 5 2 LASER
R
R38 20K R62 10K 13 16
SD[ 0. .7]
RST -
3 IRIS_COLLIMATOR U17 LM358 LM324 R_F 17
4
1 CT +5V 패턴수정 AR8 14 15 R39 20K R63 10K 18
11
REF SDI QA
ELEVATOR 패턴 수정 +24V VCC
8 R19 LASER 6.8K 11
SRC LK QB
1 C46 19
+ C29 4 7 4.7K +12V/+5V로 변 경 +12V 12 2 R40 20K R64 10K 20
GND SEN +24V Q1 RC LK QC 3 R 28 20K 100p
10uF QD
0. 1uF +5V 4 R41 20K R65 10K
TL7705A +5V 1 3 +5V_7805 +5V_7805 QE 5
VIN VOUT QF HFG
AR9 A682G 10 6 R42 20K R66 10K C31 100p
D? RLY3 D? R ED 3K XU23 OUT_EN 13 CLR QG 7 TP3
8
R92 연결 16 6 R G QH U38B
1N4007
4
5 9 VBB VCC 2 7805 + C43 9 5 XU30C R29
1
2
3
4
5
6
7
8
9
1
VBB VREF SDO +
3 100uF/ 35V R43 20K R67 10K 7 10 + 1K mA
4 D3 1N4007 74HC595 6 - 8
1 + = CLOSE LEAF 10 1 U12 R44 20K R68 10K 9 -
2 15 OUTA BRAKE 8 U12_19 19 2 SD0 LM358 LM324
4
OUTB EN 7 U12_18 18 Q1 D1 3 SD1 R45 20K R69 10K C?
CN18 +
11
PH U12_17 17 Q2 D2 4 SD2 C45
Q3 D3 ?uF
1 PA1A-24V 3 U12_16 16 5 SD3 R46 20K R70 10K
2 11 RC U12_15 15 Q4 D4 6 SD4 U18 R30 20K 100p
3 SENSE U12_14 14 Q5 D5 7 SD5 14 15 R47 20K R71 10K
4 C40 R10 R11 14 U12_13 13 Q6 D6 8 SD6 11 SDI QA 1
MODE U12_12 12 Q7 D7 9 SD7 12 SRC LK QB 2 R48 20K R72 10K C34 100p
A3952 Q8 D8 RC LK QC 3
HEADER 4 RLY4 D? RED 3K 330p 3K 0.5/2W 11 I OCS4 QD 4 R49 20K R73 10K PR EHEAT
R93 CLK +5V_7805 QE 5 XU47A
1
5 1 OUT_EN 10 QF 6 R50 20K R74 10K +12V LM358
OE CLR QG
3 IRIS COLLIMATOR용 패턴 수정 +12V로 변경 OUT_EN 13
G QH
7 TLP521-4 D23 RED 1.2K
4 D4 1N4007 +24V +5V 74HC574 R51 20K R75 10K 9 8 R98 ERROR_3 4 8
1 9 Q4E 4C
A472G SDO
+
2 CN10 XU24 AR10 R52 20K R76 10K
+12V 16 6 74HC595 10 7 D22 RED 1.2K
SD[ 0..7]
3
9 VBB VCC 2 R R53 20K R77 10K 11 Q4C 4A 6 R97 CHARGE_OK_E2
PA1A-24V 3 1 VBB VREF 74H C541 Q3E 3C
9
8
7
6
5
4
3
2
1
10 2 I OCS3 19 +5V R54 20K R78 10K
R101 7 3 + = CLOSE I RIS 10 1 1 G2 12 5 D21 RED 1.2K + C44
6 4 15 OUTA BRAKE 8
OVER_H G1 13 Q3C 3A 4 R96 FIL_OK_E1
6K 1% OUTB EN Q2E 2C 0.47uF
U34A 2 5 7 SD7 11 9
9 6 PH SD6 12 Y8 A8 8
SD5 Y7 A7 D20
3 + R108 R109 7 3 +12V 13 7 14 3 RED 1.2K
1 8 11 RC SD4 14 Y6 A6 6 15 Q2C 2A 2 R95 ROTOR_OK_E4
C? + C? 2 - +5V SENSE SD3 15 Y5 A5 5 Q1E 1C
R102 R104 10K 1% 50K 1% C41 R12 R13 14 SD2 16 Y4 A4 4 R98
100uF/16V
1
3
SD5 7 D5 Q5 14 6 IN5 OUT5 13 MWR Q3E 3C
D? R103 U34B R106 + = CLOSE LEAF ROT. 10 1 SD6 8 D6 Q6 13 7 IN6 OUT6 12 ELEVATOR UP U35A
OUTA BRAKE D7 Q7 IN7 OUT7 ADD Part's
6K 1% 5K 1% 15 8 R94 SD7 9 12 8 11 ELEVATOR DOWN 12 5 D17 R ED 1.2K CN7
OUTB EN D8 Q8 IN8 OUT8 Q3C 3A
74HC08
CN9 1N4007 6 - R107 7 CN17 1K 13 4 R 91 2
7 PH I OCS7 11 10 Q2E 2C 1 FLUORO
1 5 + 3 1 CLK COM
RC OUT_EN D16
2 10K 1% 11 2 1 ULN2803 14 3 RED 1.2K
C? C? R 111 SEN SE OE 15 Q2C 2A 2 R 90
+ CN5
H_ENABLE 2
1
D? OP490 5K 1% C42 R14 R15 14 74H C574 Q1E 1C EMG. 2
100uF/ 16V MODE
TEMP S 1N4007 0. 1u OVER HEATI NG 1 EMERGENCY
HE_P2.5
A3952 16 1
330p 3K 0.5/ 2W Q1C $PI N0
U26
1-83
KMC-650 Service Manual
84
KMC-650 Service Manual
85
KMC-650 Service Manual
86
KMC-650 Service Manual
87
KMC-650 Service Manual
88
KMC-650 Service Manual
89
KMC-650 Service Manual
- PARTⅡ. DRAWING(PCB) -
90
KMC-650 Service Manual
1) OP board
91
KMC-650 Service Manual
92
KMC-650 Service Manual
93
KMC-650 Service Manual
94
KMC-650 Service Manual
95
KMC-650 Service Manual
96
KMC-650 Service Manual
2) MAIN board
97
KMC-650 Service Manual
98
KMC-650 Service Manual
99
KMC-650 Service Manual
100
KMC-650 Service Manual
3) Fuse board
101
KMC-650 Service Manual
102
KMC-650 Service Manual
103
KMC-650 Service Manual
4) IGBT Drive Board
104
KMC-650 Service Manual
105
KMC-650 Service Manual
106
KMC-650 Service Manual
107
KMC-650 Service Manual
108
KMC-650 Service Manual
109
KMC-650 Service Manual
110
KMC-650 Service Manual
111
KMC-650 Service Manual
3. WORKSTATION
Hardware Overview
Location
Workstation
Standard Option
CART CART
112
KMC-650 Service Manual
Parts location
Remove 4 screws
1 2
4
7
2
The Processing Unit is Composed of:
Number Description
1 Power Supply connector: 220VAC
2 Monitor signal : HDMI + DVI
3 ABS signal to Interface board page:1-133, CN5
4 Camera Link connector page:1-133, CN2
5 RS-232C COM1: Main board connector page:1-133, CN4
6 RS-232C COM2: Camera connector page:1-133, CN3
7 RS-232C COM3: D.A.P Module connector (option)
113
KMC-650 Service Manual
114
KMC-650 Service Manual
115
KMC-650 Service Manual
116
KMC-650 Service Manual
How to Recovery CD
[Selector CDROM]
117
KMC-650 Service Manual
118
KMC-650 Service Manual
First, confirm EWF current states.
1. File in C driver and the patch in order description below first a current state, confirms.
1.1 My Document Batch file.
119
KMC-650 Service Manual
120
KMC-650 Service Manual
2) HOW TO EWF DISABLE C: for patch
My Documents folder
EWF-Disable Batch [ ] double click.
121
KMC-650 Service Manual
EWF ENABLE functions are NOT executed from live
Condition.
Only at the time of PC Booting, possible !!!
122
KMC-650 Service Manual
1.2 Also with different method to execute a direct command from
COMMAND windows, confirmation
From COMMAND windows which appear EWFMGR C: inputs and confirms a current status.
Type RAM Protected Type.
State ENABLE Current protecting.
Boot Command NO_CMD (current no command)
123
KMC-650 Service Manual
PC restart.
START RESTART.
From COMMAND windows which appear EWFMGR C: inputs and confirms a current status.
CHECK DISABLE
124
KMC-650 Service Manual
125
KMC-650 Service Manual
In future
Embedd xp EWF function HIBERNATE Becoming connection.
The file patch first after, COMMAND window, inputs EWFMGR C: -COMMIT
126
KMC-650 Service Manual
PC restart.
START RESTART.
127
KMC-650 Service Manual
XP Embedded one technical HIBERNATION functions is
FAST START realized.
128
KMC-650 Service Manual
2 EWF ENABLE
3 P.C Re-start
After Booting
4 CXView & StoSCU
(setting first screen)
execution
7 MY DOCUMENTS folder
CLOSE
a Hibernate-off.bat MY DOCUMENTS
b File patch
Network Connection [(TCP/IP) Setting]
c Hibernate-on.bat
d EWF ENABLE
e P.C Re-start
129
KMC-650 Service Manual
■Network Connection
1. Internet Protocol(TCP/IP) Properties Setting.
130
KMC-650 Service Manual
( )
configuration click.
PACS
131
KMC-650 Service Manual
A. Modality setting
Via Change Operator, input the ID and Password enable Machine TAP.
132
KMC-650 Service Manual
133
KMC-650 Service Manual
caution :
1) Sharpness adjust
134
KMC-650 Service Manual
135
KMC-650 Service Manual
ABS X-ray setting:
Mouse right button click[ Feature Setting] selector.
136
KMC-650 Service Manual
2) LUT setting [ ]
- Selector LUT .
EDIT
137
KMC-650 Service Manual
LUT graph application effects.
3) LEVEL setting
LEVEL Selective
138
KMC-650 Service Manual
4) Profile KEY setting
KEYBOARD KEY(F1~F10) SET
Mouse right button click [Profile] selector.
139
KMC-650 Service Manual
5) Profile setting
140
KMC-650 Service Manual
■HOW TO change WorkStation & CXView image, data base
It is not possible to restore all images from new and old PC.
Only available to use image and patient DB from one of PC
□ Restoration of setting
141
KMC-650 Service Manual
□ information of each folder for CXVIEW
▪ This is information of each folder for CXVIEW
Folder information
- CXView folder (the location C&D:\CXView)
User this folder is not necessary to change setting by User or engineer
This folder is involved in running CXView software including CXView.EXE file
142
KMC-650 Service Manual
1023
143